SPECIFICATIONS
Countdown:
99 hours, 59 minutes, 59 seconds
Resolution:
1 second
Count-up:
99 hours, 59 minutes, 59 seconds
Resolution: 1 second
BUTTONS
H - Hours
C - Clear
M - Minutes
S - Seconds
S/S - Start/Stop
CLEARING THE DISPLAY
If the timer is running, press the S/S button to stop
the timer. To clear the display to zero, press the C
button. Clearing the display will also clear the previous
countdown time from memory.
COUNTDOWN ALARM TIMING
1. Clear the display to zero.
2. Press the H button to advance the hours digits.
Press the M button to advance the minutes digits.
Press the S button to advance the seconds digits.
Press and hold the H, M, or S button to rapidly
advance the display.
3. Once the desired time is on the display, press the
S/S button to begin countdown timing.
4. When the timer reaches zero, an alarm will sound and
the timer will begin counting up.
The alarm will sound for one minute and then turn off
automatically to preserve battery life while the timer
continues counting up.
While the alarm is sounding, pressing any button will
silence the alarm and stop the count-up timing. After one
minute, pressing the S/S button will stop the count-up
timing.
MEMORY RECALL
When timing repetitive intervals, the memory function will
recall the last countdown time.
Once the count-up timing has been stopped, pressing
the H, M, or S buttons will increment the display from
the point that it was stopped and will set the timer into
countdown mode. (This will also clear the previous
countdown time from memory.)
2. Once the count up timing has been stopped, press the
S/S button to recall the original programmed time.
1. Follow steps 1 through 4 in the “Countdown Alarm
Timing” section.
3. Press the S/S button to begin countdown timing.
STOPWATCH (COUNT-UP) TIMING
1. Clear the display to zero.
2. Press the S/S button to begin count-up timing.
3. Press the S/S button to stop count-up timing.
Once timing is completed and the timer has been
stopped, press the C button to clear the display to zero.
TIMEOUT
The timer may be stopped during any running time
(countdown or count-up) by pressing the S/S button.
Timing may be resumed by pressing the S/S button.
CONVERT A TIMEOUT TO A COUNTDOWN TIME
The timer may be stopped during any running time
(countdown or count-up) by pressing the S/S button.
Once the timing has been stopped, pressing the H, M,
or S buttons will increment the display from the point
that it was stopped and will set the timer into countdown
mode. Once the desired time is on the display, press the
S/S button to begin countdown timing.
ALL OPERATIONAL DIFFICULTIES
If this timer does not function properly for any reason,
replace the battery with a new high quality battery (see
“Battery Replacement” section). Low battery power can
occasionally cause any number of “apparent” operational
difficulties. Replacing the battery with a new fresh battery
will solve most difficulties.
BATTERY REPLACEMENT
An incorrect display, no display or operational difficulties
indicate that the battery should be replaced. Slide open
the battery cover on the back of the timer. Remove the
exhausted battery and replace it with a new 1.5 volt
silver-oxide 357 size battery. Make certain the positive (+)
side is visible. Replace the battery cover.
WARRANTY, SERVICE, OR RECALIBRATION
For warranty, service, or recalibration, contact:
CONTROL COMPANY
12554 Old Galveston Rd. Suite B230
Webster, Texas 77598 USA
Ph. 281 482-1714 • Fax 281 482-9448
E-mail [email protected]
www.traceable.com
Control Company is ISO 9001:2008 Quality-Certified
by DNV and ISO/IEC 17025:2005 accredited as a
Calibration Laboratory by A2LA.
Control Company. Cat. No. 5046
Traceable® and Clip-It™ are registered trademarks/trademarks
of
Control Company.
©2016
Control Company. 92-5046-00 Rev. 5 090916
TRACEABLE®
CLIP-IT™ TIMER
INSTRUCTIONS
">
