SINGER 3210 Instruction Manual sewing machine Instruction manual

 3210 Instruction Manual
ны но а
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical appliance, basic safety should always be
followed, including the following:
Read all instructions before using this sewing machine.
>
3.
D ANG E R - To reduce the risk of electric shock:
An appliance should never be left unattended when plugged in.
Always unplug this appliance from the electric outlet immediately
after using and before cleaning.
Always unplug before re-lamping. Replace bulb with same type
rated 10 watts (110-120V area) or 15 watts (220-240V area).
WA R N | № С - To reduce the tisk of burns, fire, electric
shock, or injury to persons:
1.
2.
Do not allow to be used as a toy. Close attention is necessary when
this appliance is used by or near children.
Use this appliance only for its intended use as described in this
manual. Use only attachments recommended by the manufacturer
as contained in this manual.
Never operate this appliance if it has a damaged cord or plug, if it is
not working properly, if it has been dropped or damaged, or dropped
into water. Return the appliance to the nearest authorized dealer or
service center for examination, repair, electrical or mechanical
adjustment.
Never operate the appliance with any air openings blocked. Keep
ventilation openings of the sewing machine and foot controller free
from accumulation of lint, dust, and loose cloth,
Keep fingers away from all moving parts. Special care is required
around the sewing machine needle.
Always use the proper needle plate. The wrong plate can cause the
needle to break.
Do not use bent needles.
Do not pull or push fabric while stitching. It may deflect the needle
10.
11.
. Do not use outdoors.
13.
14.
15.
16.
17.
18.
19.
20.
21,
causing it to break.
Switch the sewing machine off ("0") when making any adjustments in
the needle area, such as threading needle, changing needle,
threading bobbin, or changing presser foot, and the like.
Always unplug sewing machine from the electrical outlet when
removing covers, lubricating, or when making any other user
servicing adjustments mentioned in the instruction manual.
Never drop or insert any object into any opening.
Do not operate where aerosol spray products are being used or
where oxygen is being administered.
To disconnect, turn all controls to the off ("O") position, then remove
plug from outlet.
Do not unplug by pulling on cord. To unplug, grasp the plug, not the
cord.
The sound pressure level under normal opsrating conditions is
75dB(A).
Please turn off the machine or unplug when the machine is not
operating properly.
Never place anything on the foot controller.
If the supply cord that is fixed with foot controller is damaged, it must
be replaced by the manufacturer or its service agent or a similar
qualified person in order to avoid a hazard.
This appliance is not intended for use by persons (including children}
with reduced physical, sensory or mental capabilities, or lack of
experience and knowledge, unless they have been given
supervision or instruction concerning use of the appliance by a
person responsible for their safety.
Children should be supervised to ensure that they do not play with
the appliance.
SAVE THESE INSTRUCTIONS
This sewing machine is intended for household use only.
Congratulations
As the owner of a new Singer sewing machine, you are about to begin an exciting adventure in
creativity. From the moment you first use your machine, you will know you are sewing on one
of the easiest to use sewing machines ever made.
May we recommend that, before you start to use your sewing machine, you discover the many
features and the ease of operation by going through this instruction book, step by step, seated
at your machine.
To ensure that you are always provided with the most modern sewing capabilities, the
manufacturer reserves the right to change the appearance, design or accessories of this
sewing machine when considered necessary.
SINGER is the exclusive trademark of The Singer Company Limited S.a.r.l. or its Affiliates.
©2013 The Singer Company Limited S.a.r.}. or its Affiliates. All rights reserved.
[| List of contents
Machine Basics
Principle Parts of the Machine....................-..»m+everre RD Reena near ra ea ercoreorerooneeoarraarrtrereeoe cercano rrccarrECerrecre. 2/3
Connecting Machine to Power Source .................... 2110 ra ere ao eeneeecaararereneenereneeneeea te ear rerererecearartcacerca crees 4
Two Step Presser Foot Lift@r…....…….….…...…....….…resirnimmmennnnnnnnnnnnnnnnnennnnnnnnnnnnmnnnnnnnnnnnnnnnnnnnnnn+nnnnnnenmnnnnn 5
[<A TO 6
Threading the Machine
Winding TNE BON TT een ssns essen essen 7
Inserting the Bobbin ..................-...=+...i e ere eee en e eee cae reneraareneorraa narco eres recenrecErANENenaer eres era rren eee rer e errar rEUUEs 8
TRIBE TENSION A sab aeas esses sree sans aessne sa nenesasenneess es ennre sees sseasanass sere ssnrnnnses 9
Threading the Upper Thread.......................=..———..—. eee recerca enero occocaaarr oe reRee rene cane eo orANON TLCAN ENRCUCeUrereeaeaaeaereneeeeeem. 10
Raising the Bobbin Thread..........................=1... ==... e eeee ee nae ENDE DOC Eer aerea crearan arenO eNUTNANONTOrDEaNaDOFU ereeeEreaeeNINeVerenenerenemas 11
Sewing
How to Choose Your Pattern... .—._ e. reee ner renane erre re ere neeeeac near eno anereerneon ener r ria rr rrCe UEErCOENArExcenrecareEmra 12
Stitch Length Dial ..................-.-....-.r.eeeererer een NN rercre eee ena eee een raDEar rare rar aer reee rne EU ORNATO NNARAOrENAR RE eneoreneace reseca temieaeeces 13
Sewing Straight Stitch ...........................emeee reee eee erre ren anareareeerererer ene reeno erre overeaaneaDenracenemem. RFF TT 14
Reverse Sewing/ Removing the Work/ Cutting the Thr@a0d.....…..…..….....rererersereansneneneerrr rence renaanerrsnae re nren sa nee an aa es a nanas 15
BINA HIM ctr reat TN een nana nana canne 16
Sew 4-Step BUttONNO!E….….….…crrcsssresessannsanssenscasencencansananenrenennentrecenceneaaeneeeranpepan aa eede nas a enr neeeee encens eee ee NES 17
SOWING ON BUÎTONS TT aan data aa tanaansanraaaanne tes deO OAOptAAANenG crane naasam san aaaan aa peAdpa sa AA ana A RAR Can ANA AVES 18
General Information
Installing the Removable Accessory STOFAGE …..….…..….....….......cruecrererersensannenranrsnararananerrnasana pannes care snaancana ca canesae caca career 19
Attaching the Presser Foot Shank...................... ee. eeeeeeee reee RI nee eee ra e eranEre ren eranareareareriseree re ercer UPTCUAUUUrECUATrEEEECCUTa 20
Needle/Fabric/Thread Chart.................— e... eeereer eres narra care eeee ee aero ro ena Area nera eran a ene a TTNFOUUTRNeCOCANRNOCUURRFAVeNTeaneEaCes 21
Darning Plate.................—— e ==mieiee errar neee eN nee reeeLere seee eee eeeenea o eDeLaDr earn ener er nee o eNO eN UtANALeaareneracecaeenaeeree ene recoararee rene 22
Maintenance and Troubleshooting
Inserting á Changing Needle ................———..—.—..—.e-..eremesenieacoee cenar e EeeURrLa na dra aer armmace nace cae ne eceo earErereeaTEDOCELANE Cn rarearreeenes 23
Changing the Bullo.............e.e. ES SES 24
Troubleshooting Guide ...............-—.-—..e=...eeee dre esse testes ene eens saatse ee nnee es eeaneeereneeeamtens reese 25
[]
Principal Parts of the Machine
—
O © © N © U ko NX —
. Thread tension dial
. Thread take-up lever
. Thread cutter
. Presser foot
. Needls plate
. Removable accessory storage
. Reverse sewing lever
. Bobbin stopper
. Stitch length dial
. Pattern selector dial
Principal Parts of the Machine
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
Horizontal spool pin
Bobbin winding spindle
Hole for second spool pin
Handwheel
Power and light switch
Main plug socket
Bobbin thread guide
Upper thread guide
Face plate
Handle
Presser foot lifter
Foot speed control
Power cord
11
[1 Connecting Machine to Power Source
Connect the machine to a power source as illustrated. {1)
This appliance is equipped with a polarized plug which must
be used with the appropriate polarized outlet. (2)
Attention:
Unplug power cord when machine is not in use.
Foot control
The foot control pedal regulates the sewing speed. (3)
Attention:
Consult a jualified electrician if in doubt of how to connect
machine to power source.
Unplug power cord when machine is not in use.
The foot control must be used with the appliance by KD-1902
(110-120V area)/ KD-2902 (220-240V area) ; 4C-316B (110-
120V area}/ 4C-326G (230V area).
Sewing light
Press main switch (A) to " 1" for power and light.
IMPORTANT NOTICE
For appliance with a polarized plug (one blade is wider than
the other). To reduce the risk of electric shock, this plug is
intended to fit in a polarized outlet only one way. If it does
not fit fully in the outlet, reverse the plug. If it still does not
fit, contact a qualified electrician to install the proper outlet.
Do not modify the plug in any way.
a. Polarized attachment piug
b. Conductor intended to be grounded
L] Two Step Presser Foot Lifter
When sewing several layers or thick fabrics, the presser foot
can be raised to a higher position for easy positioning of the
work. (A)
[] Accessories
Standard accessories (1)
em AT IO +0 Loa
. All purpose foot
. Zipper foot
. Buttonhole foot
. Button sewing foot
. Seam ripper/ brush
Edge/ quilting guide
. Pack of needles
. Spool holder
Bobbin (3x)
L-screwdriver
. Darning plate
Soft cover
Optional accessories (2)
(These 10 accessories are not supplied with this machine;
they are however available as special accessories from your
local dealer.)
m.
‚ Satin stitch foot
. Overcasting foot
. Hemmer foot
. Cording foot
“Cr го © с © 5
Auxiliary spool pin
Blind hem foot
. Darning/ embroidery foot
Gathering foot
. Quilting/ straight stitch foot
Even-feed foot
1 Standard accessories
a b с d
006806008 006905008 006909008 005914008
e
= | ; "
о С С ©,
i j k | ===
QA É>
2 Optional accessories
IER 4
006804008 006803008 006800008
006016008
006812008
_—5
[1 Winding the Bobbin
- Place thread and corresponding spool holder on to spool pin.
(1/2)
- Snap thread into thread guide. (3)
- Wind thread clockwise around bobbin winder tension discs.
(4)
- Thread bobbin as illustrated and place on spindle. (5)
- Push bobbin spindle to right. (6)
- Hold thread end. (7)
- Step on foot control pedal. (8)
- Cut thread. (9)
- Push bobbin spindle to left (10) and remove.
Please Note:
When the bobbin winder spindle is in "bobbin winding"
position, the machine will not sew and the hand wheel will
not turn. To start sewing, push the bobbin winder spindle to
the left (sewing position).
LJ Inserting the Bobbin
When inserting or removing the bobbin, the needle must
be fully raised.
- Remove the extension table, then open the hinged cover.
(1)
- Pultthe bobbin case tab (a) and remove the bobbin case. (2)
- Hoid the bobbin case with one hand. Insert the bobbin so
that the thread runs in a clockwise direction (arrow). (3)
- Pull the thread through the slit and under the finger. (4)
Leave a 6 inch tail of thread.
- Hold the bobbin case by the hinged latch. (5)
- Insert it into the shuttle. (6)
Attention:
Turn power switch to off ("O") before inserting or
removing the bobbin.
L] Thread Tension
Upper thread tension
Basic thread tension setting: "4"
To increase the tension, turn the dial to the next number up.
To reduce the tension, turn the dial to the next number down.
A. Normal thread tension for straight stitch sewing.
B. Thread tension too loose for straight stitch sewing. Turn dial
to higher number.
C. Thread tension too tight for straight stitch sewing. Turn dial to
lower number.
D. Normal thread tension for zig zag and decorative sewing.
Correct thread tension is when a small amount of the upper
thread appears on the bottom side of fabric. -
Lower thread tension
To test the bobbin thread tension, remove the bobbin case and
bobbin and hold it by suspending it by the thread. Jerk it once or
twice. If the tension is correct, the thread will unwind by about an
inch or two, 1f the tension is too tight, it does not unwind at all. If
the tension is too loose, it will drop too much. To adjust, turn the
small screw on the side of. the bobbin case.
Please note:
- Proper setting of tension is important to good sewing.
- There is no single tension setting appropriate for all stitch
functions, thread or fabric.
- A balanced tension (identical stitches both top and bottom) is
usually only desirable for straight stitch construction sewing.
- 90% of all sewing will be between "3" and "5".
- For zig zag and decorative sewing stitch functions, thread
tension should generally be less than for straight stitch sewing.
- For all decorative sewing you will always obtain a nicer stitch
and less fabric puckering when the upper thread appears on
the bottom side of your fabric.
OJ Threading the Upper Thread
This is a simple operation but it is important to carry out correctly
as by not doing so several sewing problems could result.
Start by raising the needle to its highest point (1), and continue
turning the handwheel counterclockwise until the needle just
slightly begins to descend. Raise the presser foot to releass
the tension discs.
Note: For safety, it is strongly suggested you turn off the
power before threading.
Lift up the spool pin. Place the spool of thread on the holder
with the thread coming off the spool as shown. For small
thread spools, place small side of spool holder next to spool.
(2)
Draw thread from spool through the upper thread guide (3)
and pulling thread through pre-tension spring as illustrated. (4)
Thread tension module by leading thread down right channel
and up left channel. (5) During this process it is helpful to hold
the thread between the spool and thread guide.
At the top of this movement pass thread from right to left
through the slotted eye of the take-up lever and then
downwards again. (6)
Now pass thread behind the thin wire needle clamp guide (7)
and then down to the needle which should be threaded from
front to back.
- Pull about 6-8 inches of thread to the rear beyond the needle
eye. Trim thread to length with built in thread cutter. (8)
10
[1 Raising the Bobbin Thread
Hold the upper thread with the left hand. Turn the handwheel
(1) towards you (counterclockwise) lowering, then raising
needle.
Note:
If it is difficult to raise the bobbin thread, check to make sure
the thread is not trapped by the hinged cover or the
removable accessory storage.
Gently pull on the upper thread to bring the bobbin thread up
through the needle plate hole. (2)
Lay both threads to the back under the presser foot. (3)
11
[1 Howto Choose Your Pattern
To select a stitch, simply turn the pattern selector dial (c).
The pattern selector dial may be turned in either direction.
The following page shows the recommended range of stitch
lengths.
Adjust the stitch length with the stitch length dial (b)
according to the fabric being used.
a, Reverse lever
b. Stitch length dial
¢. Pattern selector dial
12
[] Stitch Length Dial
Function of stiteh length dial for when straight stitching
For straight stitch sewing, turn the Pattern Selector Dial to
the straight stitch setting. (1) Turn the Stitch Length Dial, and
the length of the individual stitches will decrease as the dia!
approaches "0". The length of the individual stitches will
increase as the dial approaches "4". (2) Generally speaking,
use a longer stitch length when sewing heavier weight
fabrics or when using a thicker needle or thread. Use a
shorter stitch length when sewing lighter weight fabrics or
when using a finer needle or thread.
Function of stitch length dial while zig-zag stitching
Turn the Pattern Selector Dial to " WW". (3)
The density of zig-zag stitches increases as the setting of
stitch length dial approaches "0".
Neat zig-zag stitches are usually achieved at "2.5" or below.
Dense zig-zag stitches are called satin stitches. (4)
13
1 — = №) === он окт она жа == ==
= ng al, носи ин на сн N
у
[J] Sewing Straight Stitch
To begin sewing, set the machine for straight stitch. (1)
Place the fabric under the presser foot with the fabric edge
lined up with the desired seam guide line on the needle plate.
(2)
Lower the presser foot lifter, and then step on the foot
controller to start sewing. (3)
----@
Tie
sal
А
Ne
De,
TREES 2 <
=
©
se
ses
Het,
RAS
> E
Pr
RO
ESS
14
[1 Reverse Sewing
To secure the beginning and the end of a seam, press down
the reverse sewing lever (A). Sew a few reverse stitches.
Release the lever and the machine will sew forward again. (1)
(| Removing the Work
Turn the handwheel toward you (counterclockwise) to bring
the thread take up lever to its highest position, raise the
presser foot and remove work behind the needle and
presser foot, (2)
[1 Cutting the Thread
Pull the threads under and behind the presser foot. Guide
the threads to the side of the face plate and into thread
cutter (B), Pull threads down to cut. (3)
15
[J] Blind Hem
For hems on curtains, trousers, skirts, sfc.
dd Blind hem for stretch fabrics.
AAA Blind hem for firm fabrics,
Set the stitch length dial with the range shown on the
diagram at the right. Blind hems, however, are normally
sewn with a longer stitch length setting. Set the stitch width
dial at a setting appropriate for the weight/type of fabric being
sewn, within the range shown in the diagram on the right of
the page. Generally, a narrower stitch is used for lighter
weight fabrics, and a wider stitch is used for heavier weight
fabrics. Sew a test first to make sure the machine settings
are appropriate for the fabric.
Blind Hem:
Turn up the hem fo the desired width and press. Fold back
(as shown in Fig. 1) against the right side of the fabric with
the top edge of the hem extending about 7 mm (1/4") to the
right side of the foided fabric. |
Start to sew slowly on the fold, making sure the needle
touches slightly the folded top to catch one or two fabric
threads. (2)
Unfold the fabric when hemming is completed and press.
Note:
To make blind hem sewing even easier, use a blind hem
foot, available from your SINGER? retailer. (See page 6
for part number)
16
[0 Sew 4-step buttonhole
Prepare
1. Take off the all purpose foot and attach the buttonhole foot.
2, Measure diameter and thickness of button and add 0.3 cm
(1/8") for bar tacks; mark buttonhole size on fabric. (a)
3. Place fabric under the foot, so that marking on the
buttonhole foot aligns with starting marking on fabric. Lower
the foot, so that the buttonhole center line marked on the
fabric aligns with the center of the buttonhole foot. (b)
density.
Note:
Density varies according to the fabric.
Always test sew d buttonhole on the fabric you are using to
sew the buttonhole.
Follow the 4-step sequence changing from one step to
another with the pattern selector dial. When moving from step
to step through the buttonhole process, be sure that the
needle is raised before turning the pattern selector dial to the
next step. Take care not to sew too many stitches in steps 1
and 3. Use seam ripper and cut buttonhole open from both
ends towards the middle.
Tips:
- Slightly reducing upper thread tension will produce better
results.
- Use a stabilizer for fine or stretchy fabrics.
- It is advisable to use heavy thread or cord for stretch or Knit
fabrics. The zig-zag should sew over the heavy thread or
cord. (A)
17
[1 Sewing on Buttons
Install the darning plate. (1)
Change the all purpose foot to button sewing foot. (2)
Position the work under the foot.
Place the button in the desired position and lower the foot.
Set the pattern selector dial on " | " and sew a few securing
stitches. Select one of the two narrow zig-zag patterns
according to the distance between the two holes of the
button. Turn the handwheel to check if the needle goes into
the right and the left hole of the button without hitting the
button. Slowly sew on the button with about 10 stitches.
? IF
Select pattern " | " and sew a few securing stitches. (3)
If a shank is required, place a darning needle on top of the
button and sew. (4)
For buttons with 4 holes, sew through the front two holes first,
push the work forward and then sew through the back two
holes.
e
хе
E
KOE un S
{> A
o
ao JUN
NE
2
A
Cen NN J E >
ME Е
LN
E
DL
о
RRS |
es .
NN es o.
o 23» at, RRS Br
EEE
: RRR BERR E
FRITAS
=
e
3
E
e
dé
ets
il
+
©
A
и оо
e
chi
ел
Ta L
J
és “я
ee
ete
i
a
ss,
%
18
[I Installing the Removable Accessory Storage
Hold the removable accessory storage horizontally, and push
it in the direction of the arrow. (1)
To remove the accessory storage, pull it foward the left.
W
1
The standard accessories are contained inside the
removable accessory storage compartment.
To open, flip cover down as shown. (2)
2
19
[1 Attaching the Presser Foot Shank
Raise the presser bar (a) with the presser foot lifter. Attach
the presser foot shank (b) as illustrated. (1)
Attaching the presser foot
Install the pin {d) of the presser foot (e) into the cut-out {c) of
the presser foot lifer. (2)
Removing the presser foot
Push the pin (d) of the presser foot forward to separate. (3)
Attaching the edge/quilting guide
Attach the edge/quilting guide (f) in the slot as illustrated.
Adjust as needed for hems, pleats, quilting, etc. (4).
Attention:
Turn power switch to off ("O") when carrying out any of
the above operations!
20
(1 Needle/ Fabric/ Thread Chart
NEEDLE, FABRIC, THREAD SELECTION GUIDE
polyester, shirt & blouse fabrics.
NEEDLE SIZE FABRICS | THREAD
Lightweight fabrics-thin cottons, voile, silk, muslin, | Light:duty thread in cotton, nylon, polyester or
9-11 (70-80) | interlocks, cotton knits, tricots, jerseys, crepes, woven | cotton wrapped polyester.
11-14 (80-90)
Medium weight fabrics-cotton, satin, kettlecloth, sailcloth,
double knits, lightweight woolens.
Medium weight fabrics-cotton duck, woolen, heavier knits,
Most threads sold are medium size and suitable
for these fabrics and needle sizes.
Use polyester threads on synthetic materials
14 (90) terrycloth, denims, and cotton on natural woven fabrics for best
: results.
16 (100 Heavyweight fabrics-canvas, woolens, outdoor tent and
(100 quilted fabrics, denims, upholstery material (light to medium).| AWays use the same thread on top and bottom.
18 (110) Heavy woolen, overcoat fabrics, upholstery fabrics, some | Heavy duty thread.
leathers and vinyls.
IMPORTANT: Match needle size to thread size and weight of fabric.
NEEDLE, FABRIC SELECTION
NEEDLES EXPLANATION TYPE OF FABRIC
SINGER® 2020 | Standard sharp needles. Sizes range | Natural woven fabrics-wool, cotton, silk, etc.
thin to large. 9 (70) to 18 (110). Not recommended for double knits.
SINGER? 2045 | Semi-ball point needie, scarfed. Natural and synthetic woven fabrics, polyester blends.
| 9 (70) to 18 (110). Knits-polyesters, interlocks, tricot, single and double knits.
Also sweater knits, Lycra”, swimsuit fabric, elastic.
SINGER” 2032
Leather needles. 12 (80) to 18 (110). | Leather, vinyl, upholstery. (Leaves smaller hole than standard
large needle.)
Note:
1. For best sewing results always use genuine SINGER® needles.
2, Replace needle often (approximately every other garment ) and/ or at first thread breakage or skipped stitches.
21
(1 Darning Plate
For certain types of work, (e.g. darning or free-hand
embroidery), the darning plate must be used.
Install the darning plate as illustrated.
For normal sewing, remove the darning plate.
For free-motion sewing it is recommended to use a
darning/embroidery foot, available as an optional accessory
from SINGER® retailers. (See page 6 for part number of
darning/embroidery foot )
22
[J] Inserting & Changing Needles
Change the needle regularly, especially if it is showing signs
of wear and causing problems. For best sewing results
always use SINGER® brand needles.
Insert the needle as illustrated as follows:
A. Loosen the needle clamp screw and tighten again after
inserting the new needle. (1)
B. The flat side of the shaft should be towards the back.
C/D.Insert the needle as far up as it will go.
Attention:
Turn power switch to off ("О") before inserting or
removing the needle.
Needles must be in perfect condition. (2)
Problems can occur with:
A. Bent needles
B. Damaged points
C. Blunt needles
23
[1 Changing the Bulb
Disconnect the machine from the power supply by removing
the plug from the electrical socket!
Replace bulb with same type rated 10 watts (110-120V area)
or 15 watts (220-240V area).
- Loosen screw (A) as illustrated. (1)
- Remove the face plate (B).
- Unscrew the bulb and install a new one (C). (2)
- Replace the face plate and tighten screw.
Should there be any problem, consult your SINGER? retailer.
24
D) Troubleshooting Guide
Problem
Upper thread breaks
Lower thread breaks
Skipped stitches
Needle breaks
Loose stitches
Seams gather
or pucker
Uneven stitches,
uneven feed
The machine is
noisy
The machine jams
Cause
1. The machine is not threaded correctly.
2. The thread tension is too tight.
3. The thread is too thick for the needle.
4. The needle is not inserted correctly.
5. The thread is wound around the spool holder pin.
6. The needle is damaged.
1
2
3
. The bobbin case is not inserted correctly.
. The bobbin case is threaded wrong,
. The lower thread tension is too tight.
. The needle is not inserted correctly.
. The needle is damaged.
. The wrong size or type of needle has been used.
. The foot is not attached correctly.
. The needle is damaged.
. The needle is not correctly inserted.
. Wrong needle size for the fabric.
. The wrong foot is attached.
1
2
3
4
1
2
3
4
1. The machine is not correctly threaded.
2. The bobbin case is not correctly threaded.
3. Needle/ fabric/ thread combination is wrong.
4. Thread tension wrong.
i
2
3
1
2
3
. The needle is too thick for the fabric.
. The stitch length is incorrectly adjusted.
. The thread tension is too tight.
. Poor quality thread.
_ The bobbin case is incorrectly threaded.
. Fabric has been pulled.
. The machine must be lubricated.
. Lint or oil have collected on the hook or needle bar.
. Poor quality oil has been used.
. The needle is damaged.
Thread is caught in the hook.
СА) ГО —
Correction
1. Rethread the machine.
> pason
UNI WN- HON LEON BON ON
, Reduce the thread tension. (lower number)
. Select a larger needle.
" Remove and reinsert the needle. (flat side towards the back)
Remove the reel and wind thread onto reel.
Replace the needle.
Remove and reinsert the bobbin case and pull on the thread.
The thread should pull easil
. Check both bobbin and bobbin case.
"Loosen lower thread tension as described.
_ Remove and reinsert needle. (flat side towards the back)
Insert a new needle.
Choose a needle to suit the thread and fabric.
. Check and attach correctly.
. Insert a new needle.
. Insert the needle correctly. (flat side towards the back)
_ Choose a needle to suit the thread and fabric.
. Select the correct foot.
. Check the threading.
Thread the bobbin case as illustrated.
The needle size must suit the fabric and thread.
. Correct the thread tension.
. Select a finer needle.
. Readjust the stitch length.
. Loosen the thread tension.
. Select a better quality thread.
. Remove bobbin case, thread and insert correctly
. Do not pull on the fabric while sewing, let it be drawn through
by the machine.
. Lubricate as described.
Clean the hook and feed dog as described.
. Only use good quality sewing machine ой.
. Replace t
- Remove the upper thread and bobbin case, turn the handwheel
backwards an
e needls,
forwards by hand and remove the thread.
Lubricate as described.
25
This marking indicates that this product should not be disposed ^\
with other household wastes throughout the European Union. To
prevent possible harm to the environment or human health from
uncontrolled waste disposal, recycle it responsibly to promote the
sustainable reuse of material resources. To return your used
device, please use the return and collection systems or contact
the retailer where the product was purchased. They can take this
product for environmental safe recycling. 7
CE - Authorised Representative
VSM Group AB, SVP Worldwide
Drottninggatan 2, SE-56184, Huskvarna, SWEDEN
">