advertisement
INSTALLATION INSTRUCTIONS FOR PART 99-8224
APPLICATIONS
Toyota Matrix 2009-10
Pontiac Vibe 2009-10
(Excluding Factory Navigation Models)
99-8224
KIT FEATURES
• DIN Radio Provision With Pocket
• ISO Mount Radio Provision With Pocket
KIT COMPONENTS
• A) Rading Housing • B) ISO Brackets • C) Trim Plate
A
B C
Harness & Antenna Connections (sold separately)
• 70-1761 - Toyota Harness 87-up
TOOLS REQUIRED:
Small Flat Blade Screwdriver/ Panel Removal Tool
• Socket Set
99-8224 DASH DISASSEMBLY
Toyota Matrix/Pontiac Vibe 2009-10
A
1 Disconnect the negative battery terminal to prevent an accidental short circuit.
2 Unclip and remove the radio trim panel including the a/c vent. (Figure A)
3 Remove (4) 10 MM bolts securing the radio. Unplug and remove the radio.
(Figure B)
Continue to kit preparation.
B
99-8224 KIT ASSEMBLY
DIN RADIO PROVISION WITH POCKET
* Note: Refer also to the instructions included with the aftermarket radio.
1 Slide the DIN cage into the Radio
Housing and secure by bending the metal locking tabs outward. (Figure A)
2 Slide the aftermarket radio into the cage until it snaps into place. (Figure B)
Continue to final assembly.
A
B
STACKED MOUNT RADIO PROVISION WITH POCKET
* Note: Refer also to the instructions included with the aftermarket radio.
1 Mount the ISO Brackets to the Radio using the screws supplied with the radio. (Figure A)
2 Slide the Radio into the Radio Housing until the side clips snap into place.
(Figure B)
3 Snap the Trim plate into the Radio
Housing. (Figure B)
Continue to final assembly.
A
B
99-8224 FINAL ASSEMBLY
FINAL ASSEMBLY
A
B
(A) Strip wire ends back 1/2"
B) Twist ends together
C) Solder
D) Tape
C
D
1
2
3
Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.)
Re-connect the negative battery terminal and test the unit for proper operation.
Reassemble radio and dash assemblies in reverse order of disassembly.
FINAL WIRING CONNECTIONS
Make wiring connections using the EIA color code chart shown below and the instructions included with the head unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and individually tape off ends of any unused wires to prevent electrical short circuit.
METRA / EIA WIRING CODE
12V Ignition / Acc. . . . . . . . . . Red
12V Batt / Memory. . . . . . . . . Yellow
Ground. . . . . . . . . . . . . . . . . . Black*
Power Antenna. . . . . . . . . . . . Blue
Amp Turn-On . . . . . . . . . . . . . Blue / White
Amp Ground. . . . . . . . . . . . . . Black / White
Illumination . . . . . . . . . . . . . . Orange
Dimmer . . . . . . . . . . . . . . . . . Orange / White
Right Front (+) . . . . . . . . . . . . Gray
Right Front (-). . . . . . . . . . . . . Gray/ Black
Left Front (+) . . . . . . . . . . . . . White
Left Front (-). . . . . . . . . . . . . . White / Black
Right Rear (+) . . . . . . . . . . . . Violet
Right Rear (-) . . . . . . . . . . . . . Violet / Black
Left Rear (+) . . . . . . . . . . . . . Green
Left Rear (-) . . . . . . . . . . . . . . Green / Black
*NOTE: When a Black wire is not present, ground radio to vehicle chassis.
All colors may not be present on all leads due to manufacturer’s specifications.
METRA ACCESSORIES STEREO DASH KITS
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project