Oce OP1030 Operation Manual

पीडीएफ

दस्तावेज़

KM-C850 / KM-C850D

Operation Guide

<Set-up Edition>

ALWAYS read this Operation Guide thoroughly before use. After reading, maintain it in good condition and keep it together with the Operation Guide for your copier.

Trademark Information

• Novell and NetWare are registered trademarks of Novell, Inc.

• IBM and IBM PC-AT are trademarks of International Business Machines Corporation.

• PowerPC is a trademark of International Business Machines Corporation of America and other corporations.

• Adobe and Acrobat are trademarks of Adobe Systems Incorporated.

• CompactFlash and CF are trademarks of SanDisk Corporation.

All other company and product names contained in this Operation Guide are trademarks or registered trademarks of their respective companies. The designations ™ and ® will not be used in this Operation Guide.

All rights reserved. No part of this material may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying, recording or by any information storage and retrieval system, without permission in writing from the Publisher.

Legal Restriction On Copying

• It may be prohibited to copy copyrighted material without permission of the copyright owner.

• It is prohibited under any circumstances to copy domestic or foreign currencies.

• Copying other items may be prohibited.

IBM PROGRAM LICENSE AGREEMENT

THE DEVICE YOU HAVE PURCHASED CONTAINS ONE OR MORE SOFTWARE PROGRAMS (“PROGRAMS”) WHICH BELONG TO

INTERNATIONAL BUSINESS MACHINES CORPORATION (“IBM”). THIS DOCUMENT DEFINES THE TERMS AND CONDITIONS

UNDER WHICH THE SOFTWARE IS BEING LICENSED TO YOU BY IBM. IF YOU DO NOT AGREE WITH THE TERMS AND

CONDITIONS OF THIS LICENSE, THEN WITHIN 14 DAYS AFTER YOUR ACQUISITION OF THE DEVICE YOU MAY RETURN THE

DEVICE FOR A FULL REFUND. IF YOU DO NOT SO RETURN THE DEVICE WITHIN THE 14 DAYS, THEN YOU WILL BE ASSUMED

TO HAVE AGREED TO THESE TERMS AND CONDITIONS.

The Programs are licensed not sold. IBM, or the applicable IBM country organization, grants you a license for the Programs only in the country where you acquired the Programs. You obtain no rights other than those granted you under this license.

The term “Programs“ means the original and all whole or partial copies of it, including modified copies or portions merged into other programs. IBM retains title to the Programs. IBM owns, or has licensed from the owner, copyrights in the Programs.

1. License

Under this license, you may use the Programs only with the device on which they are installed and transfer possession of the Programs and the device to another party. If you transfer the Programs, you must transfer a copy of this license and any other documentation to the other party. Your license is then terminated. The other party agrees to these terms and conditions by its first use of the Program.

You may not:

1) use, copy, modify, merge, or transfer copies of the Program except as provided in this license;

2) reverse assemble or reverse compile the Program; or

3) sublicense, rent, lease, or assign the Program.

2. Limited Warranty

The Programs are provided “AS IS.”

THERE ARE NO OTHER WARRANTIES COVERING THE PROGRAMS (OR CONDITIONS), EXPRESS OR IMPLIED, INCLUDING,

BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

Some jurisdictions do not allow the exclusion of implied warranties, so the above exclusion may not apply to you.

SUPPLEMENT TO AGREEMENT FOR SOFTWARE BUNDLING AND DISTRIBUTION FOR ALDC

3. Limitation of Remedies

IBM’s entire liability under this license is the following;

This limitation will not apply to claims for bodily injury or damages to real or tangible personal property for which IBM is legally liable.

IBM will not be liable for any lost profits, lost savings, or any incidental damages or other economic consequential damages, even if

IBM, or its authorized supplier, has been advised of the possibility of such damages. IBM will not be liable for any damages claimed by you based on any third party claim. This limitation of remedies also applies to any developer of Programs supplied to IBM. IBM’s and the developer’s limitations of remedies are not cumulative. Such developer is an intended beneficiary of this Section. Some jurisdictions do not allow these limitations or exclusions, so they may not apply to you.

4. General

1) For any claim (including fundamental breach), in any form, related in any way to this license, IBM’s liability will be for actual damages only and will be limited to the greater of; a) the equivalent of U.S.$25,000 in your local currency; or b) IBM’s then generally available license fee for the Program

You may terminate your license at any time. IBM may terminate your license if you fail to comply with the terms and conditions of this license. In either event, you must destroy all your copies of the Program. You are responsible for payment of any taxes, including personal property taxes, resulting from this license. Neither party may bring an action, regardless of form, more than two years after the cause of action arose. If you acquired the Program in the United States, this license is governed by the laws of the State of New York. If you acquired the Program in Canada, this license is governed by the laws of the Province of Ontario. Otherwise, this license is governed by the laws of the country in which you acquired the Program.

About this Operation Guide

This Operation Guide <Set-up Edition> is meant to be read when the Printer Board is installed in your copier and the copier is to be used as a local printer or network printer. It contains explanations on set-up procedures for using the copier as a printer.

As the required set-up and configurations for the printer may differ depending upon the environment in use in the connected computer, please read those sections related to your specific computer environment and perform the appropriate set-up and configuration explained there.

The Operation Guide <Functions Edition> contains explanations on printing, performing certain settings and configurations, and the procedures required at your computer.

About the On-Line Manual

The On-Line Manual for this Operation Guide is a PDF (Portable Document Format) file and is located on the CD-ROM that is included with this product. The Adobe Acrobat Reader software is required in order to access the On-Line Manual.

The installer for Adobe Acrobat Reader is also included on the CD-ROM so the software can be installed onto your hard disk from there.

iii

Getting connected

When connecting the printer directly to your computer (with a parallel cable or USB cable)…

1 Connecting the printer directly to your computer with a parallel cable or USB cable ..................

Page 4

Parallel cable or USB cable

2 Installing the printer driver into your computer .... Refer to the Functions Edition

CD-ROM

When connecting the printer to a network…

Hub

Network cable

1 Connecting a network cable

(100BASE-TX, 10BASE-T, etc.) to the printer.............................

Page 5

2 Performing network (TCP/IP) settings at the printer ...............

Page 6

3 Installing the printer driver into your computer ... Refer to the Functions Edition

CD-ROM

1. Preparations ............................................................................................................. 2

1-1 Accessories ................................................................................................................................................ 2

1-2 Required items ...........................................................................................................................................2

1-3 Name of parts (main body) ........................................................................................................................ 2

1-4 Name of parts (operation panel) ................................................................................................................ 3

2. Set-up ........................................................................................................................ 4

2-1 Connecting the printer cable ...................................................................................................................... 4

2-2 Connecting the network cable ...................................................................................................................5

2-3 Installing the software ................................................................................................................................5

2-4 Network (TCP/IP) settings .........................................................................................................................6

3. Troubleshooting ....................................................................................................... 8

3-1 Canceling printing ......................................................................................................................................8

3-2 When an error message appears… ......................................................................................................... 9

3-3 Basic troubleshooting chart ..................................................................................................................... 13

4. Specifications ......................................................................................................... 14

1. Preparations

1-1 Accessories

• CD-ROM x 2

• This Operation Guide

1-2 Required items

• When connecting the printer directly to your computer: Parallel cable (IEEE1284 compliant, 1.5 m or shorter) or USB cable (Full-Speed USB2.0

compliant, 5.0 m or shoter)

• When connecting the printer to a network: Ethernet cable (10BASE-T or 100BASE-TX)

*When you use a USB, 10BASE-T or 100BASE-TX cable, make sure it is a shielded cable.

1-3 Name of parts (main body)

1 USB interface connector

This USB interface conforms to Full-Speed USB2.0. Use a USB cable to connect this connector with a USB port of your computer.

2 Memory card (CompactFlash) slot

Insert the optional Memory Card (CompactFlash) here. Optional fonts, macros, and forms can be written into this Memory Card. For details, refer to the Operation Guide <Functions Edition>.

3 Network interface connector

Use a 10BASE-T/100BASE-TX network cable to connect the printer to a network.

4 Parallel interface connector

Use a parallel cable to connect the connector with a parallel port of your computer.

5 Operation panel

Use when performing settings at the printer itself.

6 Power switch

Turn this switch ON ( | ) when using the printer. Turn this switch Off ( ) when connecting the printer cable, etc.

1. Preparations

1-4 Name of parts (operation panel)

1 Printer key (indicator)

Press to switch to the printer mode. The indicator is lit when the mode is engaged.

2 Status indicator

Flashes/lights to indicate printer status.

Lights green while receiving data.

Lights amber when a printing error has occurred.

Flashes amber when an error that does not interrupt printing has occurred.

3 Printer Priority key (indicator)

Press during print out of copies or of a fax reception in order to interrupt that current operation and give priority to print out of a print job from a computer. The indicator is lit when the mode is engaged.

4 Touch panel

Displays printer status and keys for operating various functions.

5 Numeric keys

Use to set enter settings directly.

● Touch panel in the printer mode

6 Printer Menu key

Press to set printer defaults.

7 Cancel key

Press to stop printing or to clear an error message.

8 GO key

Press to restart printing as well as to initiate form feeding. This key is also used to toggle the printer between online and offline.

2. Set-up

2-1 Connecting the printer cable

To connect the printer directly to your computer, use either a parallel cable or USB cable.

CAUTION: ALWAYS turn the main switch to the printer Off BEFORE connecting the printer cable.

Turn the main switch located on the left side of the printer

Off and then turn the power off to your computer as well.

Connect the other end of the printer cable to the parallel interface connector or USB interface connector on your computer.

Turn the main switch to the printer back On.

Connect the printer cable to the parallel interface connector or USB interface connector located at the back of the right side of the printer.

* For details on printer interface setup, see “Functions

Edition”.

2-2 Connecting the network cable

To connect the printer to a network, use an Ethernet cable

(100BASE-TX or 10BASE-T).

Turn the main switch located on the left side of the printer

Off.

2. Set-up

2-3 Installing the software

Perform the following procedure to install into your computer the printer driver and other software that is appropriate to the operating system in use in that computer. For information on installing the required software, refer to the Functions Edition.

Connect the network cable to the Ethernet connector at the back of the right side of the printer.

Connect the other end of the network cable to your hub.

Turn the printer’s main switch back On.

Make network settings. (See “Network settings” on page 6.)

2. Set-up

2-4 Network (TCP/IP) settings

To use the printer as a network printer, it is necessary to set an IP address for the printer.

Notes

• The IP address that should be registered here will differ depending upon your network environment. Check with your network administrator BEFORE performing this setting.

• If you are using a DHCP server to automatically configure the IP address, this setting will not be necessary because DHCP server configuration is already enabled as the factory default setting.

* To cancel the setting midway through it, press the Stop/Clear key.

Press the Printer key. The printer will switch to the printer mode.

Use the “

▲” and “▼” cursor keys to select “TCP/IP” and then touch the “Change” key.

Select “On” under the “TCP/IP” setting and “Off” under the

“DHCP” setting.

Touch the “Printer Menu” key.

Use the “

▲” and “▼” cursor keys to select “IP Address” and then touch the “Change” key.

Touch the “Interface” key.

Use the numeric keys to input the address. Input the first block of 3 digits of the address in the highlighted area.

• Press the sharp (#) key to set the address after inputting each block of 3 digits.

Touch the “Network” tab key.

Enter the next 3 digits and press the sharp (#) key.

• To change an entered address, press the sharp (#) key to select a 3-digit block and use the numeric keys to enter the correct address.

2. Set-up

Use the “

▲” and “▼” cursor keys to select “Gateway” and touch the “Change” key.

Repeat the same procedure for the remaining blocks of the address. Once the input of the IP address is completed, touch the “Close” key. The display will return to the “TCP/IP” screen.

• To cancel the entered address, touch the “Back” key. The address that was shown before you entered a new address will reappear.

Enter the Gateway address in the same way you entered the IP address in steps 8 to 10.

When you are finished making all of the network settings, touch the “Close” key.

Use the “

▲” and “▼” cursor keys to select “Subnet Mask” and touch the “Change” key.

Touch the “Close” key.

Enter the Subnet Mask address in the same way you entered the IP address in steps 8 to 10.

Touch the “Close” key. The printer will switch back to the printer mode.

3. Troubleshooting

3-1 Canceling printing

Perform the following procedure when you want to stop printing or you want to clear data.

IMPORTANT!

• By performing this operation you will be canceling ALL print jobs that are currently waiting in the printer’s memory to be printed.

Touch the “Cancel” key.

Select a printer interface and touch the “Confirm” key.

• To abort the cancel operation, touch the “Cancel” key.

Printing will be canceled.

3. Troubleshooting

3-2 When an error message appears…

If an error message appears on the operation panel, first check the following tables for cause of the trouble and then perform the corresponding procedure. For more detailed information, refer to the Operation Guide for your copier as well as the Operation Guide for any optional equipment that is installed in your machine.

Display message

Add paper in drawer (cassette).

XX size (XXX)

Use alternative? Press GO

Set paper Press GO

Place paper.

Add staples.

Call service.

Department code mismatch

Exceeded print quantity limit.

Exceeded pre-registered printing quantity.

Error in printer mode

RAM Disk error Press GO

Procedure

The size or type of paper selected for printing does not match the size or type of paper in the cassette. Replace the paper in the drawer with that of the correct size and type.

• If you want to switch to and print from a different cassette, select the desired cassette on the touch panel and then touch the “GO” key.

• The following commands will be displayed in the printer mode.

GO: Force-prints onto the current size or type of paper.

Cancel: Cancels the printing operation completely.

Displayed after changing the drawer. Touch the “GO” key.

This mode feeds a stack of multiple sheets one at a time. Every time you want to feed a sheet, touch the “GO” key.

The cassette has run out of paper. Add paper.

The finisher (option) has run out of staples. Refer to the Operation Guide for the finisher and replenish the staples.

Trouble has occurred within the printer. Contact your service representative or an authorized service center.

The department code you entered does not match the registered one. Check the department code that is registered in the printer driver.

The amount of printing accomplished has exceeded the acceptable capacity as set under copy management. In order to print further, change the copy management setting in the printer.

This message will appear when a printer error occurs and the machine is in a mode other than the printer mode. Press the Printer key to switch to the print mode screen and the corresponding error message will be displayed.

Code:##

Check the error code displayed in place of ## and refer to the following.

01: Format error. Turn power Off and On again.

02: The RAM disk mode is Off. Turn it On.

03: A write error has occurred. Turn Off write protection.

04: The RAM disk does not have enough area to store the data. Delete any unnecessary data to make more room.

05: The selected file could not be found. Check the file name and whether it is on the RAM disk or not.

06: There is not enough system memory. Increase memory capacity.

98: Some of the data being collated was not read. Job data is corrupt.

3. Troubleshooting

Display message

Memory card error Press GO

Hard disk error Press GO

KPDL error Press GO

Memory Card error Insert again

Procedure

Code:##

Check the error code displayed in place of ## and refer to the following.

01: Format error. Reformat the memory card.

02: Memory card load error. Correctly load the memory card.

03: A write error has occurred. Turn Off write protection.

04: The memory card does not have enough area to store the data. Delete any unnecessary data to make more room.

05: The selected file could not be found. Check the file name and whether it is on the memory card or not.

Code:##

Check the error code displayed in place of ## and refer to the following.

01: Format error. Reformat the hard disk.

02: Hard disk load error. Correctly load the hard disk.

03: A write error has occurred. Turn Off write protection.

04: The hard disk does not have enough area to store the data. Delete any unnecessary data to make more room.

05: The selected file could not be found. Check the file name and whether it is on the hard disk or not.

06: There is not enough system memory. Increase memory capacity.

20: The hard disk is loaded in the wrong slot. Load the hard disk in the correct slot.

85: An illegal name has been used for the virtual tray. Rename the tray correctly.

86: The wrong password was used for the virtual mailbox. Input the correct password.

88: Some of the data in the virtual mailbox was not read. Job data is corrupt.

97: No more jobs can be saved. The limit has been reached. Increase the number of storable jobs and available area.

98: Some of the data in the job was not read. Job data is corrupt.

Code:##

The current print job cannot continue. A KPDL error report can be printed out from the Printer

Menu. Touching the “GO” key prints out the data that has already been processed. If auto recovery time has been set, printing will resume automatically when the set time elapses.

For more information, see “KPDL Error Report print out” and “Auto Continue On/Off and

Recovery Time” in “Functions Edition”.

The Memory Card (CompactFlash) was removed during operation under the menu for printer-related settings. Reinsert the Memory Card.

* BE SURE to turn the main switch Off BEFORE inserting the Memory Card.

Display message

Insert the same memory card

Format error Memory card

Option interface error

File not found Press GO

Read fonts:Failed

Read macro:Failed

Warning low memory

Warning image adapt

Print overrun Press GO

Memory overflow Press GO

Virtual mailbox full

Interface occupied

3. Troubleshooting

Procedure

The Memory Card (CompactFlash) could not be detected during an operation in which the printer was reading data from that card. Reinsert the Memory Card.

* BE SURE to turn the main switch Off BEFORE inserting the Memory Card.

Initialization of the Memory Card (CompactFlash) currently inserted is necessary.

Code:10

The optional interface board is loaded in the wrong slot. Turn power Off and load the board in the correct slot.

File error. Touch the “GO” key.

The printer failed to read the font data. Try to read the font data again.

The printer failed to read the macro. Try to read the macro again.

There is not enough memory. You can check how much printer memory there is by printing out a status page. Delete any unnecessary font data and macros.

Because there is not enough memory, printing cannot be performed at the set resolution.

Either add more memory to the printer or change the resolution.

A data overrun error has occurred due to insufficient memory.

• Press the Printer key to switch to the printer mode. Following commands will be displayed.

GO: Continues printing.

Cancel: Cancels the printing operation completely.

• If auto recovery time has been set, printing will resume automatically when the set time elapses.

• Once this error message is displayed, “Page Protect” will be turned “On” automatically.

The current print job could not be completed due to insufficient memory in the printer.

• Press the Printer key to switch to the printer mode. Following commands will be displayed.

GO: Continues printing. The data that has already been processed will be printed out and the remaining portion of the print job will be printed onto the following page.

Cancel: Cancels the printing operation completely.

• If you are using a RAM disk, reduce the size of the RAM disk. If this error occurs often, it is recommended that you install additional memory into the printer. For more detailed information on adding memory, contact your service representative or an authorized service center.

• If auto recovery time has been set, printing will resume automatically when the set time elapses.

There is not enough area in the virtual mailbox. Print out data in the virtual mailbox.

The selected interface is currently is use. Wait for a while and then attempt the operation again.

3. Troubleshooting

Display message

Option ROM error Press GO

Format error Hard Disk

Check chad box

Procedure

An error occurred when reading the optional ROM. Press the Printer key to switch to the printer mode and then touch the “GO” key to clear the error.

Initialize the hard disk.

Either the punch waste box is not correctly installed or it is full. Reposition or empty it as necessary.

3. Troubleshooting

3-3 Basic troubleshooting chart

If you experience trouble while you are using this machine as a printer, refer to the table below to perform minor adjustments. If trouble persists, contact your service representative or an authorized service center.

* For information in regard to general mechanical trouble with the machine, refer to the Operation Guide for your copier.

Problem

Nothing is printed out

Text is not printed correctly

Print out is not correct

Check point

Is the power cord loose?

Is the power On to the printer?

Is the printer cable appropriate and is it connected properly?

Did you connect the printer cable

AFTER you turned the power to the printer On?

Is the printer off-line? (Is the Status indicator flashing amber?)

Procedure

Connect the power cord securely to a power source.

Turn the main switch to the printer On.

Be sure to use a compliant printer cable and make sure it is connected properly.

Connect the printer cable BEFORE you turn the power to the printer On.

Is the printer cable appropriate and is it connected properly?

Is the setting configuration in your computer correct?

Is the emulation protocol setting correct?

Perform the appropriate procedure to put the printer on-line.

1 Press the Printer key to switch to the printer mode.

2 Touch the “GO” key.

3 The Status indicator will go out.

Be sure to use a compliant printer cable and make sure it is connected properly.

Confirm the settings in the printer driver as well as in the software application in use.

Check the emulation protocol setting.

Reference page

—

4. Specifications

CPU ................................................................... PowerPC 750CX (400 MHz)

Printing Speed ................................................... Monochrome one-sided print: 31 pages/min. (A4 [11" x 8 1/2"])

Color one-sided print: 8 pages/min. (A4 [11" x 8 1/2"])

Printing Resolution ............................................. 600 dpi x 600 dpi

Maximum Printing Size ...................................... A3 (11" x 17")

RAM Memory Capacity ...................................... Installed: 128 MB

Maximum: 640 MB (with two units of optional 256 MB expansion memory installed)

Interface ............................................................. Parallel interface (IEEE 1284 compliant) x 1

USB interface Full-Speed USB 2.0 x 1

Network interface x 1

Installed Fonts .................................................... PCL: 80

KPDL: 136

* Specifications are subject to change without notice.

MEMO

2003. 5

3H780020A

नमस्ते! मैं एक एआई चैटबॉट हूं जिसे विशेष रूप से Oce OP1030 Operation Manual के साथ आपकी सहायता करने के लिए प्रशिक्षित किया गया है. मैंने दस्तावेज़ की अच्छी तरह से समीक्षा की है और आपको आवश्यक सटीक जानकारी का पता लगाने या स्पष्ट और सरल शब्दों में सामग्री को समझाने में मदद कर सकता हूं. चाहे आप विशिष्ट सुविधाओं, समस्या निवारण चरणों या सामान्य उपयोग पर मार्गदर्शन की तलाश कर रहे हों, अपने प्रश्न पूछने के लिए स्वतंत्र महसूस करें. आप अपनी चिंताओं या जरूरतों के बारे में जितनी अधिक जानकारी प्रदान करेंगे, उतनी ही सटीक और प्रभावी ढंग से मैं आपकी सहायता कर सकता हूं!