Pentax Optio Optio 60 User manual

FCC STATEMENT (For customers in USA)
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired
operation.
Note:
This equipment has been tested and found to comply with the limits for Class B digital devices, pursuant to Part 15
of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation.This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Use of shielded cable is required to comply with Class B limits in Subpart B of Part 15 of the FCC rules.
Do not make any changes or modifications to the equipment unless otherwise specified in the manual.
If such changes or modifications should be made, you could be required to stop operation of the
equipment.
For customers in Canada
This Class B digital apparatus meets all requirements of the Canadian Interference - Causing Equipment
Regulations.
Pour les utilisateurs au Canada
Cet apareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du
Canada.
EN-1
READ THIS FIRST
Trademark Information
PENTAX and Optio are trademarks of PENTAX Corporation.
QuickTime and QuickTime logo are trademarks used under license. The QuickTime logo is registered
in US and other countries.
This product supports PRINT Image Matching III. PRINT Image Matching enabled digital still cameras,
printers and software help photographers to produce images more faithful to their intentions. Some
functions are not available on printers that are not PRINT Image Matching III compliant. Copyright
2001 Seiko Epson Corporation. All Rights Reserved. PRINT Image Matching is a trademark of Seiko
Epson Corporation.
The PRINT Image Matching logo is a trademark of Seiko Epson Corporation.
) is a trademark.
SD logo (
All other brands or product names are trademarks or registered trademarks of their respective owners.
Product Information
Product design and specifications are subject to change without notice. This includes primary product
specifications, software, software drivers, and user’s manual. This User Manual is a general reference
guide for the product.
The product and accessories that come with your digital camera may be different from those described
in this manual. This is due to the fact that different retailers often specify slightly different product
inclusions and accessories to suit their market requirements, customer demographics, and geographical
preferences. Products very often vary among retailers especially with accessories such as batteries,
chargers, AC adapters, memory cards, cables, carrying cases/pouches, and language support.
Occasionally a retailer will specify a unique product color, appearance, and internal memory capacity.
Contact your dealer for precise product definition and included accessories.
The illustrations in this manual are for the purpose of explanation and may differ from the actual
design of your digital camera.
The manufacturer assumes no liability for any errors or discrepancies in this user manual.
For user manual and driver updates, refer to our website or contact your dealer.
EN-2
SAFETY INSTRUCTIONS
Read and understand all Warnings and Cautions before using this product.
Warnings
If foreign objects or water have entered the camera, turn the power off and remove the
batteries and the AC power adapter.
Continued use in this state might cause fire or electric shock. Consult the store of purchase.
If the camera has fallen or its casing has been damaged, turn the power off and remove the
batteries and the AC power adapter.
Continued use in this state might cause fire or electric shock. Consult the store of purchase.
Do not disassemble, change or repair the camera.
This might cause fire or electric shock. For repair or internal inspection, ask the store of
purchase.
Use the supplied AC adapter only with the indicated power supply voltage.
Use with any other power supply voltage might cause fire or electric shock.
Do not use the camera in areas near water.
This might cause fire or electric shock. Take special care during rain, snow, on the beach, or
near the shore.
Do not place the camera on inclined or unstable surfaces.
This might cause the camera to fall or tilt over, causing injury.
Keep the batteries out of the reach of children.
Swallowing batteries might cause poisoning. If the battery is accidentally swallowed, immediately
consult a physician.
Do not use the camera while you are walking, driving or riding a motorcycle.
This might cause you to fall over or result in traffic accident.
EN-3
Cautions
Insert the batteries paying careful attention to the polarity (+ or –) of the terminals.
Inserting the batteries with its polarities inverted might cause fire and injury, or damage to the
surrounding areas due to the battery rupturing or leaking.
Do not fire the flash close to anyone’s eyes.
This might cause damage to the person’s eyesight.
Do not subject the LCD monitor to impact.
This might damage the glass on the screen or cause the internal fluid to leak. If the internal fluid
enters your eyes or comes into contact with your body or clothes, rinse with fresh water. If the
internal fluid has entered your eyes, consult a physician to receive treatment.
A camera is a precision instrument. Do not drop it, strike it or use excessive force when
handling the camera.
This might cause damage to the camera.
Do not use the camera in humid, steamy, smoky, or dusty places.
This might cause fire or electric shock.
Do not remove the battery immediately after long period of continuous use.
The battery becomes hot during use. Touching a hot battery might cause burns.
Do not wrap the camera or place it in cloth or blankets.
This might cause heat to build up and deform the casing, resulting in fire. Keep the camera in
a well-ventilated place.
Do not leave the camera in places where the temperature may rise significantly, such as
inside a car.
This might adversely affect the casing or the parts inside, resulting in fire.
Before you move the camera, disconnect cords and cables.
Failure to do this might damage cords and cables, resulting in fire and electric shock.
EN-4
Notes on Battery Usage
When you use the battery, carefully read and strictly observe the Safety Instructions and the notes
described below:
Different battery types and surrounding temperatures may affect the battery performance.
Avoid using batteries in extremely cold environments as low temperatures can shorten the battery life
and reduce camera performance. This low temperature will also influence Alkaline battery performance,
therefore Ni-MH rechargeable battery is highly recommended.
Using new rechargeable batteries for the first time, or rechargeable batteries that have not been used
for an extended period of time might affect the number of pictures that can be taken. Therefore, to
maximize their performance and lifetime, we recommend that you fully charge such batteries and
discharge them for at least one complete cycle before use. Nevertheless, batteries whose expiry date
has passed could not be restored by this procedure.
The battery may feel warm when using the camera for an extended period of time or using the flash
continuously. This is normal and not a malfunction.
The camera may feel warm when being used continuously or for an extended period of time. This is
normal and not a malfunction.
If you will not be using the batteries for an extended period of time, remove them from the camera to
prevent leakage or corrosion.
Never use batteries of different types (together) or mix old and new batteries.
Always keep the terminals in a clean state.
Never use manganese batteries.
Risk of explosion if battery is replaced by an incorrect type.
Dispose of used batteries according to the instructions.
EN-5
CONTENTS
INTRODUCTION ................................................ 8
PHOTOGRAPHY MODE................................... 24
Package Contents............................................ 9
Shooting Images - The Basics..........................24
GETTING TO KNOW YOUR CAMERA.............. 10
Setting Image Resolution and Quality ................ 25
Using the Zoom Function................................... 26
Front View...................................................... 10
Rear View......................................................... 11
Mode Dial ...................................................... 12
Using the Flash............................................... 27
Setting Focus...................................................28
LCD Monitor Information..................................... 13
Using the Self-Timer.........................................29
Adjusting the Exposure (EV Compensation)......... 30
PREPARING THE CAMERA............................. 15
Setting White Balance...................................... 31
Installing the Batteries (Optional Accessory) ....... 15
Using the AC Power Adapter
(Optional Accessory)..........................................16
Inserting and Removing an SD Memory Card
(Optional Accessory) ........................................17
Attaching the Camera Strap.............................. 18
LED Indicators..................................................18
GETTING STARTED........................................... 19
Turning the Power On/Off ................................. 19
Choosing the Screen Language......................... 20
Setting the Date and Time ................................21
Formatting an SD Memory Card or Internal
Memory............................................................ 22
Using the LCD Monitor....................................... 23
EN-6
USING THE MODE DIAL.................................... 32
Simple Mode.....................................................32
Program Mode ................................................. 32
Picture Mode..................................................... 33
Aperture Priority Mode....................................... 33
Shutter Speed Priority Mode...............................34
Manual Mode..................................................... 34
ADVANCED SHOOTING................................... 35
High Speed Continuous..................................... 35
Auto Bracket ................................................... 36
Selecting the Metering Mode ............................. 37
PLAYBACK MODE - THE BASICS..................... 38
EDITING SOFTWARE INSTALLATION..............58
Viewing Images ............................................... 38
Installing ACDSee for PENTAX...........................58
Magnifying Images .......................................... 39
Thumbnail Display .......................................... 40
USING THE DIGITAL CAMERA AS A PC CAMERA...59
Slideshow Display ........................................... 41
Resizing an Image ........................................... 42
MOVIE MODE.................................................... 43
Recording Movie Clips ...................................... 43
Playing Back Movie Clips ................................. 44
PLAYBACK MODE – ADVANCED FEATURES...45
Step 1: Install the PC camera driver..................59
Step 2: Connect the digital camera to your
computer.............................................60
Step 3: Run your application software
(i.e. Windows NetMeeting)......................60
MENU OPTIONS...............................................61
Playing Back Still Images/Movie Clips on TV ........45
Camera Menu.................................................... 61
Movie Menu ................................................... 65
Deleting Images/Movie Clips.............................. 46
Protecting Images/Movie Clips ........................... 47
Playback Menu............................................... 66
Setup Menu.................................................... 68
Setting the DPOF............................................. 48
Connecting to a PictBridge-Compatible Printer......50
CONNECTING THE DIGITAL CAMERA TO
OTHER DEVICES............................................. 71
TRANSFERRING FILES FROM YOUR DIGITAL
CAMERA TO COMPUTER...................................54
SPECIFICATIONS............................................ 72
Step 1:
Install the USB driver .........................55
APPENDIX........................................................ 73
Step 2:
Connect the digital camera to your
computer...........................................56
WARRANTY POLICY..........................................76
Step 3:
Download images or movie clips............57
EN-7
INTRODUCTION
Thank you for purchasing this new digital camera!
Equipped with a 6.0 Megapixels CCD sensor, your camera delivers high quality, 2848 x 2136 resolution
images. Other features provided by the camera include the following:
6.0 Megapixels
A high-resolution CCD sensor provides 6.0
megapixels for high quality of images.
Auto flash
An auto flash sensor automatically detects
the shooting (lighting) conditions and
determines whether the flash should be used.
2.0” LTPS color image LCD monitor
Optical zoom: 1x~3x
Digital zoom: 1x~4x
Approx. 12MB internal (built-in) memory
Images can be captured without using a
memory card.
Support for SD memory card for memory
expansion
You may wish to expand the memory capacity
(up to 1GB capacity) by using an additional
memory card.
EN-8
USB connection (USB 2.0 Full Speed)
Still images or movie clips that you have
recorded can be downloaded to your computer
using the USB cable (A USB driver is required
for Win 98 and Win98SE).
DPOF functionality
DPOF can be used to print your images on a
DPOF compatible printer by simply inserting
the memory card.
PictBridge support
You can connect the camera directly to printer
that supports PictBridge and perform image
selection and printing using the camera monitor
screen and controls.
Provided editing software: ACDSee for PENTAX
You can enhance and retouch your images on
your computer by using the provided editing
software.
Package Contents
Carefully unpack your kit box and ensure that you have the following items. In the event that any item is
missing or if you find any mismatch or damage, promptly contact your dealer.
Common Product Components:
Digital Camera
Operating manuals
Quick Start Guide
USB Cable
Software CD-ROM (S-SW38)
AV Cable
Camera Strap
Two AA alkaline batteries (for checking the camera's functionality)
************************************************************************************
Common (Optional) Accessories (not included with the camera):
AC power adapter (supplied by PENTAX)
SD memory card (commercially available)
Battery Charger (commercially available)
Accessories and components may vary by retailer.
EN-9
GETTING TO KNOW YOUR CAMERA
Front View
1
2
3
4
5
6
7
8
9
10
EN-10
1. Shutter button
6. Viewfinder window
2. Flash
7. Self-timer LED
3.
8. PC (USB) / AV terminal
Power button
4. Mode dial
9. DC IN 3V terminal
5. Microphone
10.Lens
Rear View
1
2
3
4
5
6
7
8
9
10
11
12
13
16
1. Viewfinder
15
14
9.
2. Diopter adjustment dial
3. Viewfinder LED
4.
/
10. Zoom in (telephoto) button
Zoom out (wide-angle) button
Exposure compensation button
Delete button
12.
OK button
6. Strap holder
13. MENU
Menu button
7. Arrow button (Up)
14. Battery / SD card cover
Macro button
15. Tripod socket
Arrow button (Left)
16. LCD monitor
8. Playback button
Arrow button (Down)
11. DISPLAY Display button
Thumbnail button
5.
Arrow button (Right)
Self-timer button
Flash button
EN-11
Mode Dial
You can select from seven shooting modes and setup mode according to shooting conditions to achieve
the desired effect.
1
2
3
8
4
5
7
Mode
1.
Program
2.
Picture
3.
Aperture priority
4.
Shutter speed priority
5.
Manual
6.
7.
8.
Setup
Movie
Simple
EN-12
6
Description
Select this mode to permit the shutter speed and aperture
to be set automatically.
Select this mode to select the Picture mode according to the
shooting scene.
Select this mode to specify the aperture value while the camera
sets the corresponding shutter speed.
Select this mode to specify the shutter speed while the camera
sets the corresponding aperture.
Select this mode to permit full manual control over exposure,
aperture and other settings.
Select this mode to adjust the camera settings.
Select this mode to record movie clips.
Select this mode for point-and-shoot action.
LCD Monitor Information
Camera Mode
1
1. Flash mode
] Auto
[
] Auto + Red-eye reduction
[
[
] Flash on
[
] Flash off
2. Mode indication
[
2
3
4
5
6M
52
6
7
8
9
13
10
11
] Simple mode
]
]
]
]
]
Setup mode
Movie mode
Aperture priority mode
[
Program mode
[
Shutter speed priority
mode
] Picture mode
[
[
] Manual mode
3. Image quality
] Best
[
] Better
[
[
] Good
4. Recorded Pixels
[ 6 ] 2848 x 2136
[ 4 ] 2272 x 1704
[ 2 ] 1600 x 1200
[ 0.3 ] 640 x 480
[
[
[
M
M
M
M
01.07.2005
5. Possible number of shots
6. Memory status
: Built-in memory (without card)
: SD Memory Card
7. Remaining battery status
[
] Full battery power
] Medium battery power
[
] Low battery power
[
[
] No battery power
8. Self-timer mode
[ 2 ] 2 sec. delay
[ 10 ] 10 sec. delay
[
] 10+2 sec. delay
[
] Timer off
12
9. White balance
[No icon] Auto
[
]
Daylight
]
Cloudy
[
[
]
Tungsten light
[
]
Fluorescent light
10.Drive mode
]
Standard
[
[
]
HS Continuous
]
Auto Bracket
[
11.Focus area
12.Date
13.Focus mode
]
Macro
[
[
]
Infinity
[ Std.] Auto focus
EN-13
1
2
3
4
Movie Mode
1.
2.
3.
4.
5.
6.
7.
Movie mode
Recordable movie time available
Memory status
Battery power indicator
Focus area
Flash mode
Date
00:49
6
5
01.07.2005
1
2
7
3
Image Playback
1.
2.
3.
4.
Playback mode
Memory status
Battery power indicator
Playback information
100-0001
Size
EV
01.07. '05
2848X2136
4
0.0
05:22
1
1
2
3
4
Movie Playback
1.
2.
3.
4.
5.
6.
Playback mode
Movie mode
Memory status
Battery power indicator
Playback information
Playback indicator
6
100-0001
Size
EV
01.07. '05
320X240
5
0.0
05:22
1
EN-14
PREPARING THE CAMERA
Installing the Batteries (Optional Accessory)
You can use 2 AA size batteries (alkaline or Ni-MH rechargeable) to power the camera. Make sure that
the power of the digital camera is off before inserting or removing the batteries.
1
1
2
2
DISPLAY
MEMU
1. Make sure the camera is turned off.
2. Open the battery cover.
3. Insert the batteries in the correct orientation as shown in the
illustration.
4. Close the battery cover.
To remove the batteries,turn the camera off before removing
batteries and hold the camera with the battery cover facing
upward, then open the battery cover.
Be careful not to drop the batteries when opening or closing the battery cover.
Due to the characteristics of AA alkaline battery, camera performance may deteriorate. AA alkaline battery is not
recommended except in emergencies and checking the camera's functionality.
EN-15
Using the AC Power Adapter (Optional Accessory)
Use of the AC power adapter is recommended if you intend to use the LCD monitor for a long time or
connect the camera to a PC.
1. Make sure your camera is turned off.
2. Connect one end of the AC power adapter to the camera jack labeled "DC IN 3.0V".
3. Connect the other end to an electrical outlet.
DC terminal
AC adapter
DC IN 3.0V
To power outlet
AC power cable
Make sure to use only the AC power adapter specified for the camera. Damage caused by the use of an incorrect
adapter is not covered under the warranty.
To prevent unexpected auto power off resulting from no battery power left during the process of transferring your
images to the computer, use the AC power adapter as a power supply.
The AC power adapter can only be used to power the camera. Batteries cannot be charged inside the camera.
EN-16
Inserting and Removing an SD Memory Card (Optional Accessory)
The digital camera comes with approx. 12MB of internal memory, allowing you to store captured still
images or movie clips in the digital camera. Moreover, you can also expand the memory capacity by using
an optional SD (Secure Digital) memory card so that you can store more files.
1. Make sure your camera is turned off before inserting or removing
an SD card.
2. Open the SD card cover.
3. Insert an SD card in the correct orientation as shown in the
illustration.
4. Close the SD card cover.
To remove the SD card, make sure the camera is turned off.
Press lightly on the edge of the memory card and it will eject.
DISPLAY
MEMU
Be sure to format an SD memory card with this digital camera before
using it. Refer to section in the manual titled “Formatting an SD Memory
Card or Internal Memory”. (Refer to EN-22 for further details.)
To prevent valuable data from being accidentally erased from an SD card,
you can slide the write protect tab (on the side of the SD memory card)
to “LOCK”.
To save, edit, or erase data on an SD memory card, you must unlock the card.
Write-protect switch
EN-17
Attaching the Camera Strap
Attach the strap as shown in the illustration.
1
ME
MU
DISP
LA
Y
LED Indicators
Indicator
LED indicator
LED indicator
LED indicator
LED indicator
Self-timer indicator
EN-18
State
Solid red
Solid green
Blinking red
Blinking red
Blinking green
Description/Activity
The digital camera is powered up.
The digital camera is ready to record images (or movies).
USB communication/transfer in progress.
Charging the flash.
The self-timer function is activated.
2
GETTING STARTED
Turning the Power On/Off
Press the
button until the digital camera turns on.
To turn the power off, press the
button again.
Power button
PEN
TAX
DISPLA
Y
EN-19
Choosing the Screen Language
Follow the steps below to choose the desired language.
and turn your camera on by pressing
1. Rotate the mode dial to
the
button.
The [Set-up1] menu is displayed.
PEN
TAX
DISPL
AY
2. Use to select [Language], then press the
button.
Set-up1
Set-up2
Set-up3
Format
Sound
Date Adjust
Language
OK :
3. Use or to select the language you want.
button to confirm.
4. Press the
EN-20
Off
d/m/y
English
4/4
Setting the Date and Time
Follow the steps below to set the date display style, current date and time.
and turn your camera on by pressing
1. Rotate the mode dial to
the
button.
The [Set-up1] menu is displayed.
button.
2. Use to select [Date Adjust], then press the
You may press or to switch the date types.
Set-up1
Set-up2
Set-up3
Format
Off
Sound
Date Adjust
Language
d/m/y
English
OK :
3. Press or to select Year, Month, Day and Time fields.
To increase a value, press .
To decrease a value, press .
The time is displayed in 24-hours format.
button after all fields are set.
4. Press the
3/4
Date Adjust
01 /07 / 2005
04:00
OK :
Select :
The date illustration shown is for the purpose of explanation and may differ from the actual setting of your camera.
EN-21
Formatting an SD Memory Card or Internal Memory
The term “Formatting” means preparing an “SD Memory Card” to record images; this process is also called
“initialization”. This utility formats the internal memory (or memory card) and erases all stored images and
data.
and turn your camera on by pressing
1. Rotate the mode dial to
the
button.
The [Set-up1] menu is displayed.
button.
2. Use to select [Format], then press the
Set-up1
Set-up2
Off
Sound
d/m/y
Date Adjust
English
Language
OK :
3. Use or to select [OK], then press the
Set-up3
Format
1/4
button to confirm.
Format
OK
Cancel
OK :
When you format an SD memory card, be aware that all data will be
permanently erased. Protected images are also erased.
To format the internal memory, do not insert a memory card into the camera. Otherwise, you will format the
memory card.
Formatting is an irreversible action and data cannot be recovered at a later time.
An SD memory card having any problem cannot be properly formatted.
EN-22
Using the LCD Monitor
Your camera is equipped with a 2.0" full color TFT LCD monitor to help you compose images, replay
recorded images/movie clips or adjust menu settings. The mode icons, text and numbers displayed on
the monitor may vary according to the current settings.
1.
2.
3.
4.
,
,
,
,
,
Rotate the mode dial to
Press the
button to turn on the power.
Compose your scene on the LCD monitor.
Press the shutter button.
or
.
MENU
DISPLAY
The LCD monitor darkens in strong sunlight or bright light. This is not a malfunction.
To prevent your images from being blurred while pressing the shutter button, always hold it carefully. This is
especially important when you are shooting under low lighting conditions, since your camera may decelerate the
shutter speed to ensure your images are properly exposed.
EN-23
PHOTOGRAPHY MODE
Shooting Images - The Basics
1. Rotate the mode dial to
,
,
,
,
or
and turn your
camera on by pressing the
button.
2. Compose the image on the monitor screen so that the main
subject is within the focus frame.
3. Press the shutter button down half way to focus the image.
When you press the shutter button down half way, the
camera’s Auto Focus feature automatically focuses the
image. Proper exposure is determined and locked at the
same time.
4. Press the shutter button the rest of the way down to capture the
image.
PEN
TAX
DISPLAY
The actual captured image appears to be larger than the one displayed by the LCD after the image has been
captured.
Pressing the DISPLAY button switches the LCD monitor display mode. Each time you press the DISPLAY button,
the display changes in the following order: Focus Frame On Indicators Off Composition Line On LCD Off.
EN-24
Setting Image Resolution and Quality
As you get to know the digital camera, you can set the image resolution (number of vertical and
horizontal pixels) and image quality (compression ratio) based on the types of images you want to shoot.
These settings affect the number of images that can be stored in the internal memory, or on a memory card.
Higher resolution and higher quality images provide finer detail but cause the images’ file size to be larger.
To change image resolution or image quality, perform these steps below:
,
,
, ,
or
and turn your
1. Rotate the mode dial to
button.
camera on by pressing the
2. Press the MENU button.
The [Mode1] menu is displayed. In the
mode, [Simple]
menu is displayed.
button.
3. Use to select [Recorded pixels], then press the
Mode1
Mode2
Mode3
Recorded pixels
6M
Quality Level
WB
Auto
White Balance
I S O Sensitivity
OK :
Auto
Exit :
1/4
Recorded pixels
4. Use or to select the desired setting, then press the
button to confirm.
5. Follow the step 3 and 4 above to set the [Quality Level].
6 M 2848x2136
4 M 2272x1704
2 M 1600x1200
0.3
M 640x480
OK :
Exit :
4/4
The possible number of shots and recording time depend on the storage size, resolution and quality settings and
the subject of the image to be captured.
You can resize the images later. Please refer to the section in this manual titled “Resizing an Image”. (Refer to EN42 for further details.)
EN-25
Using the Zoom Function
This camera is equipped with 3x optical zoom. The lens moves during the optical zoom photography,
allowing you to capture telephoto and wide-angle shots. By using the optical zoom function; images
button.
appear closer by pressing the button, or smaller away by pressing the
Moreover, you can further enlarge the subjects with 4x digital zoom by pressing continuously the
button. It is activated after your camera reaches its maximum optical zoom factor (3x). A useful feature
as it is, however, the more the image is enlarged, the more pixelated the image will appear.
To capture a zoomed image, perform the following steps:
,
,
, ,
or
and turn your
1. Rotate the mode dial to
camera on by pressing the
button.
button.
2. Adjust the magnification ratio by using the /
To access the optical zoom function, press the button as
far as it can go. Press it again to activate the digital zoom.
To exit the zoom photography, press continuously the
button.
The status of digital magnification is displayed on the LCD
monitor.
3. Compose your scene and press the shutter button.
To enable digital zoom feature, set the [Mode2- Digital Zoom] to [On] in the
to EN-63 for further details.)
EN-26
MENU
DISPLAY
,
,
,
or
mode. (Refer
Using the Flash
The flash is designed to function automatically when lighting conditions warrant the use of flash. You
can take an image using a desired flash mode to suit your circumstances.
1.
2.
3.
4.
5.
,
,
, ,
or .
Rotate the mode dial to
button to turn on the power.
Press the
Press / .
Use or to select the desired flash mode.
Compose your scene and press the shutter button.
6M
2
01.07.2005
The table below will help you to choose the appropriate flash mode:
Flash mode
Auto
Auto + Red-eye
reduction
Flash on
Flash off
Description
The flash fires automatically according to suit the photographic conditions.
Use this mode to reduce the red-eye phenomenon when you want to take
natural-looking photographs of people and animals in low-light conditions.
When taking photographs, the red-eye phenomenon can be reduced by asking
the subject (person) to look at the digital camera or get as close to the digital
camera as possible.
The flash will always fire regardless of the surrounding brightness. Select this
mode for recording images with high contrast (backlighting) and deep shadows.
Use this mode where the flash use is prohibited or when the distance to the
subject is too far away for the flash to have any effect.
EN-27
Setting Focus
Images can be captured with the focus determined automatically using auto focus. You may over-ride
the auto focus and specify [
] macro or [
1. Rotate the mode dial to
2. Press / .
,
,
,
] infinity.
,
or
.
6M
2
3. Use or to select the desired focus mode.
4. Compose your scene and press the shutter button.
Std.
01.07.2005
The table below will help you choose the appropriate focus mode:
Focus mode
Description
Macro
Infinity
Std. Auto Focus
EN-28
Select macro to capture close-up images. When the lens is zoomed to its widest
position you may focus objects as close as 5 cm.When the lens is zoomed to its
telephoto position (3x zoom) you may focus objects as close as 30 cm.
Select the infinity-focus setting when you want to capture images of subject at a
distance of infinity.
Select auto focus for most occasions when you want the camera to automatically
determine the focus setting.
Using auto focus any object at a range of focus is 50 cm or greater can be in
focus.
Using the Self-Timer
The self-timer can be used in situations such as group shots. When using this option, you should either
mount the camera on a tripod (recommended) or rest it on a flat, level surface.
1.
2.
3.
4.
5.
6.
Secure the camera to a tripod or place it on a stable surface.
Rotate the mode dial to
,
,
,
,
or .
button to turn on the power.
Press the
Press / .
Use or to select the desired self-timer mode.
Compose your scene and press the shutter button.
The self-timer function is activated.
The photograph is then taken after the preset time.
To cancel the self-timer at any time, press the shutter button.
6M
2
2
10
01.07.2005
The table below will help you choose the appropriate self-timer mode:
Self-timer mode Description
2
10
Timer off
The self-timer is off.
2 seconds
The image is captured about 2 seconds after the shutter is pressed. This mode is
useful for preventing camera shake.
10 seconds The image is captured about 10 seconds after the shutter is pressed. This mode is
suitable for the shots in which the photographer has to be included.
10+2 seconds The first image is captured about 10 seconds after the shutter button is pressed,
and then the second image is captured 2 seconds later. This mode is convenient
when capturing group images in succession.
After one shot is taken, the self-timer mode is turned off.
If you wish to take another image using the self-timer, repeat these steps.
EN-29
Adjusting the Exposure (EV Compensation)
You can manually adjust the exposure determined by the digital camera. Use this mode when the proper
exposure cannot be obtained, for example, when the contrast (difference between bright and dark
areas) between the subject and the background is extremely high. The EV compensation value can be
set in the range from –2.0EV to +2.0EV.
1.
2.
3.
4.
,
,
,
or .
Rotate the mode dial to
Press the
button to turn on the power.
Press .
Use or to set the range of EV compensation value from
–2.0EV to +2.0EV.
5. To exit the menu, press the
EV
+0.3
button.
Select:
EN-30
OK :
Setting White Balance
This feature lets you make adjustments to compensate for different lighting types according to your
shooting conditions.
1.
2.
3.
4.
,
,
,
or .
Rotate the mode dial to
Press the
button to turn on the power.
Press the MENU button.
Use to select [White Balance], then press the
Mode1
Mode2
Mode3
Recorded pixels
button.
6M
Quality Level
White Balance
Auto
Sensitivity
OK :
5. Use or to select the desired setting, then press the
button to confirm.
6. To exit the menu, press the MENU button.
Auto
Exit :
3/4
White Balance
Auto
Daylight
Cloudy
Tungsten Light
OK :
Exit :
1/5
White Balance
Fluorescent Light
OK :
Exit :
5/5
EN-31
USING THE MODE DIAL
Simple Mode [
]
(Simple) mode is the simplest way which allows you to take still pictures without having to set special
functions or manual adjustments. The camera sets the optimal focusing and exposure.
and turn your camera on by pressing
1. Rotate the mode dial to
button.
the
2. Compose your subject within the focus frame.
3. Press the shutter button down halfway to focus the image.
When you press the shutter button down half way, the
camera’s Auto Focus feature automatically focuses the image.
Proper exposure is determined and locked at the same time.
4. Press the shutter button the rest of the way down to capture the
image.
Program Mode [
PEN
TAX
DISPLAY
]
In the
(Program) mode, the camera automatically sets the shutter speed and aperture for taking still
images. You can adjust other functions, such as flash mode or continuous shooting mode.
1. Rotate the mode dial to
and turn your camera on by pressing
the
button.
2. Compose your subject within the focus frame.
3. Press the shutter button to capture the image.
PEN
TAX
DISPLAY
EN-32
Picture Mode [
]
You can select the Picture mode according to the shooting scene. There are 4 available modes in
Picture mode.
] Night scene: This mode allows you to take photographs of people against a dusk or night-time background.
[
[
] Landscape: This mode allows you to take photographs of distant scenery or landscapes.
[
] Portrait: Select this mode to make people stand out with the background out-of-focus.
] Sport: This mode allows you to shoot fast moving objects.
[
and turn your camera on by pressing
1. Rotate the mode dial to
the
button. A guide appears for a few seconds.
2. Press the
button.
3. Use or to select the desired scene mode.
button to confirm the selection.
4. Press the
5. Compose your subject within the focus frame.
6. Press the shutter button to capture the image.
Aperture Priority Mode [
Night Scene
Select:
OK :
]
In this mode, images are captured with the priority given to aperture. The shutter speed is automatically
set according to the aperture. The aperture will affect the depth-of-field of the picture.
If you set a large aperture (lower F value), you can capture portrait images with an out-of-focus background.
Alternatively, if you set a small aperture (higher F value), both close objects and distant objects will be in
focus, for example when capturing subjects in the foreground together with landscape images.
and turn your camera on by pressing
1. Rotate the mode dial to
button. A guide appears for a few seconds.
the
2. Press the
button.
button.
3. Set the aperture value with or , and press the
4. Compose your subject within the focus frame.
5. Press the shutter button to capture the image.
Av
F2.8
Select:
OK :
EN-33
Shutter Speed Priority Mode [
]
If you set a fast shutter speed, you can capture images of moving subjects that look as if they are still. If
you set a slow shutter speed, you can capture images that give the impression that the subject is in motion.
and turn your camera on by pressing
1. Rotate the mode dial to
button. A guide appears for a few seconds.
the
button.
2. Press the
3. Set the aperture value with or , and press the
Tv
button.
4. Compose your subject within the focus frame.
5. Press the shutter button to capture the image.
1/125S
Select:
Manual Mode [
OK :
]
In manual mode, the aperture value and the shutter speed can be varied individually. This can be useful
for compensating tricky lighting conditions, for getting creative results or for capturing night-time scenes.
1. Rotate the mode dial to and turn your camera on by pressing
the
button. A guide appears for a few seconds.
button.
2. Press the
3. Use or to select aperture/shutter speed item.
4. Adjust the value with or , and press the
button.
5. Compose your subject within the focus frame.
6. Press the shutter button to capture the image.
Av/Tv
F2.8
2s
Select:
Press the shuter button halfway to confirm if the exposure is set correctly on the LCD monitor.
EN-34
OK :
ADVANCED SHOOTING
High Speed Continuous
This mode is used for continuous shooting. 3 pictures are taken continuously once the shutter button is
pressed.
,
,
,
,
or and turn your
1. Rotate the mode dial to
camera on by pressing the
button.
2. Press the MENU button, then use to select the [Mode2] menu.
In the
mode, press the MENU button.
button.
3. Use to select [Drive Mode], then press the
Mode1
Mode2
Drive Mode
Digital Zoom
On
Instant Review
Off
OK:
4. Use or to select [HS Continuous], then press the
5. To exit the menu, press the MENU button.
Mode3
AE Metering
Exit :
2/4
Exit :
2/3
button.
Drive Mode
The
indicator is displayed on the monitor screen.
6. Press the shutter button halfway to lock the focus.
7. Press the shutter button to capture a sequence of images.
Standard
HS Continuous
Auto Bracket
OK :
In High Speed Continuous mode, the flash mode will be set to OFF automatically.
EN-35
Auto Bracket
In this mode, the camera automatically changes the exposure within a set range to take three shots after
you press the shutter button once. Auto Bracket settings can be combined with exposure compensation
settings to extend the adjustment range.
,
,
,
or
and turn your
1. Rotate the mode dial to ,
camera on by pressing the
button.
2. Press the MENU button, then use to select the [Mode2] menu.
mode, press the MENU button.
In the
3. Use to select [Drive Mode], then press the
button.
4. Use or to select [Auto Bracket], then press the
button.
5. To exit the menu, press the MENU button.
indicator is displayed on the monitor screen.
The
6. Press the shutter button to capture the three images.
In Auto Bracket mode, the flash mode will be set to OFF automatically.
EN-36
Drive Mode
Standard
HS Continuous
Auto Bracket
OK :
Exit :
3/3
Selecting the Metering Mode
You can select the metering mode that sets which part of the subject to measure to determine the
exposure.
,
,
,
or
and turn your
1. Rotate the mode dial to
button.
camera on by pressing the
2. Press the MENU button, then use to select the [Mode2] menu.
button.
3. Use to select [AE Metering], then press the
Mode1
Mode2
Drive Mode
Digital Zoom
On
Instant Review
Off
OK:
4. Use or to select the desired metering mode, then press the
button.
[
Center-Weighted]: Averages the light metered from the
entire frame, but gives greater weight to the subject matter
at the center.
[
Spot]: The exposure is determined by the small area in
the center of the screen only.
5. To exit the menu, press the MENU button.
6. Compose your subject within the focus frame.
7. Press the shutter button to capture the image.
Mode3
AE Metering
Exit :
1/4
AE Metering
Center-Weighted
Spot
OK :
Exit :
1/2
EN-37
PLAYBACK MODE - THE BASICS
Viewing Images
You can display the still images one by one.
1. Rotate the mode dial to
, ,
, , , or
and turn your
button.
camera on by pressing the
2. Press the
button.
The last recorded image appears on the LCD monitor.
3. Use or to select the desired images.
To view the previous image, press .
To view the next image, press .
100-0001
Size
EV
01.07. '05
2848X2136
+1.7
05:22
1
The playback information displayed on the LCD monitor will disappear after 2 seconds.
mark will be displayed. (Refer to EN-47 for further details.)
For protected images/movie clips,
mark will be displayed. (Refer to EN-48,49 for further
For images selected for printing with DPOF setting,
details.)
If there is no image stored in the internal memory or on the memory card. [No Image] message will appear on the
monitor.
EN-38
Magnifying Images
While reviewing your images, you may enlarge a selected portion of an image. This magnification allows
you to view fine details. The zoom factor displayed on the screen shows the current magnification ratio.
button.
1. Press the
The last recorded image appears on the LCD monitor.
To view the previous image, press .
To view the next image, press .
/
button.
2. Adjust the zoom ratio by using the Zoom
To enlarge the selected image, press the button.
button.
To return to the normal image, press the
The magnification factor is displayed on the LCD monitor.
3. To view different portions of the images, press / / / to
adjust the display area.
1.5X
The magnification factors range from 1x to 4x (within 7 stages: 1.0x, 1.5x, 2.0x, 2.5x, 3.0x, 3.5x and 4.0x).
EN-39
Thumbnail Display
This function allows you to view 9 thumbnail images on the LCD monitor simultaneously so you may
search for a particular image.
button.
1. Press the
The last recorded image appears on the LCD monitor.
/
button once.
2. Press the
Nine thumbnail images are displayed simultaneously.
movie mode icon will be
For recorded movie clips, the
displayed.
3. Use / / / to move the cursor to select the image to be
displayed at regular size.
4. Press the
button to display the selected image on full screen.
EN-40
1
2
5
7
Slideshow Display
The slide show function enables you to play your images back automatically in sequential order. This is
very useful and entertaining feature for reviewing recorded images and for presentations.
button.
1. Press the
The last recorded image appears on the LCD monitor.
2. Press the MENU button, then use to select [Slideshow] and
button.
press the
PlayBack2
PlayBack1
Slideshow
Protect
DPOF
OK :
3. Use or to set the playback interval, then press the
button.
The slide show starts.
The movie clips are displayed the first frame image, and not
played back.
To stop slide show, press the
button.
Exit :
1/3
Slideshow
3sec
5sec
10sec
OK :
Return :
You can adjust the slide show display interval within the range of 3 sec., 5 sec., 10 sec..
EN-41
Resizing an Image
You can change the image size of a captured image to one of the following sizes: 2848 x 2136 pixel,
2272 x 1704 pixel, 1600 x 1200 pixel and 640 x 480 pixel.
button.
1. Press the
The last recorded image appears on the LCD monitor.
mode, use or to select the desired images.
2. In the
To view the previous image, press .
To view the next image, press .
3. Press the MENU button, and press to select [PlayBack2].
button.
4. Use or to select [Resize] and press the
PlayBack1
Quality Change
Image Copy
OK :
5. Use or to select the desired setting, then press the
to confirm.
PlayBack2
Resize
Exit :
1/3
button
Resize
6 M 2848x2136
4 M 2272x1704
2M 1600x1200
0.3
M 640x480
OK :
EN-42
Return :
MOVIE MODE
Recording Movie Clips
This mode allows you to record movie clips with sound via built-in microphone.
1. Rotate the mode dial to
and turn your camera on by pressing
button.
the
2. Press the shutter button to start recording.
3. To stop recording, press the shutter button again.
1
PEN
TAX
DISPL
AY
00:49
01.07.2005
The zoom function of optical zoom (3x) can be activated before you start recording the movie clips.
To enable digital zoom feature, set the [Digital Zoom] to [On] on the movie menu.
Pressing the DISPLAY button switches the LCD monitor display mode. Each time you press the DISPLAY button,
the display changes in the following order: Focus Frame On Indicators Off Composition Line On LCD Off.
EN-43
Playing Back Movie Clips
You can play back the recorded movie clips on the LCD monitor. However, the sound recorded with
movie clips can only be played back on TV or computers.
button.
1. Press the
2. Use or to go through the images until the movie clip you
want to play back is displayed.
To view the previous image, press .
To view the next image, press .
button to start playing back the movie clips.
3. Press the
To pause or resume movie playback, press the
button
again.
100-0001
Size
EV
01.07. '05
320X240
0.0
05:22
1
The playback information displayed on the LCD monitor will disappear after 2 seconds.
The zoom function cannot be activated for movie clips.
To playback the movie clips on the computer, we recommend you to use Windows Media Player 9.0 (WMP 9.0).
You can download WMP version from the website at www.microsoft.com.
EN-44
PLAYBACK MODE – ADVANCED FEATURES
Playing Back Still Images/Movie Clips on TV
You can also playback your images on a TV screen. Before connecting to any device, make sure to
select NTSC/PAL system to match the video output system of the video equipment you are going to
connect to the digital camera, then turn off all devices to be connected.
PC/AV terminal
DC IN 3.0V
1. Connect one end of the AV cable to the AV terminal of the
digital camera.
2. Connect the other end to the AV input socket of the TV set.
3. Turn the TV and digital camera on.
4. Playback the images/movie clips.
The method of operation is the same as playing back still
images and movie clips on the digital camera.
The sound recorded with movie clips can only be played back on TV or computers.
EN-45
Deleting Images/Movie Clips
Use this function to delete one or all images/movie clips stored in the internal memory or memory card. Please
note that the deleted images or movie clips cannot be recovered. Exercise caution before deleting a file.
, ,
, , , or
and turn your
1. Rotate the mode dial to
button.
camera on by pressing the
2. Press the
button.
The last recorded image appears on the LCD monitor.
3. Use or to select the image you want to delete.
4. Press the
Delete
This Image
Delete All
Cancel
button.
5. Use or to select [This Image] or [Delete All] by your
preference, then press the
button.
6. When the delete message appears, use or to select [OK],
then press the
button to confirm the deletion.
If you wish to cancel the deletion, select [Cancel].
OK :
Delete
OK
Cancel
OK :
Protected images cannot be deleted with the delete function.
EN-46
Protecting Images/Movie Clips
Set the data to read-only to prevent images from being erased by mistake.
1. Press the
button.
The last recorded image appears on the LCD monitor.
mode, use or to select the desired images.
2. In the
To view the previous image, press .
To view the next image, press .
3. Press the MENU button.
button.
4. Use to select [Protect] and press the
5. Use or to choose the desired setting, then press the
button.
PlayBack1
PlayBack2
Slideshow
Protect
DPOF
OK :
Exit :
2/3
Protect
[This Image]: Protect one image/movie.
[All Imagesl]: Protect all images/movies (at once).
This Image
All Images
OK :
6. Use or to select [Protect], then press the
confirm.
Return :
button to
This Image
Protect
mode.
Press the MENU button to return to the
The
indicator appears on the selected image.
If you wish to cancel the protect function, select [Unprotect].
Unprotect
OK :
Return :
EN-47
Setting the DPOF
DPOF (Digital Print Order Format) allows you to embed printing information on your memory card. By
using DPOF, you can select an image to be printed and then specify how many prints or which image you
would like. Take your memory card to a DPOF enabled printer that accepts memory cards. The DPOF/
card-compatible printer will read the embedded information on the memory card and print your images as
specified.
To configure print settings for a single image / all images.
Step
Figure
1
Procedure
Press the
.
to mark
100-0001
Size
2848X2136
EV
* The playback information displayed on the LCD monitor will disappear
+1.7
01.07. '05
05:22
1
PlayBack2
PlayBack1
Slideshow
2
button, then use or to select the desired image you want
Protect
after 2 seconds.
Press the MENU button. Use or to select [DPOF], then press the
button.
DPOF
OK :
Exit :
3/3
Use or to select by your preference, then press the
button.
DPOF
Single image
All lmages
3
Reset All
OK :
EN-48
Return :
[Single image]: To configure print settings for a single image.
[All Images]:
To configure print settings for all images.
[Reset All]:
Returns all basic settings to the digital camera’s default
settings.
Step
Figure
Procedure
Use or to select by your preference, then press the
Single Image
Copies
2
Date
Allows you to select image quantity (0~10). Use or to
set the image quantity.
The date of recording can be printed directly on the images.
Select [OK] or [Cancel] with or .
To exit the mark function, use or to select [Return],
button.
then press the
[Copies]:
Cancel
Return
4
OK :
Exit :
1/3
[Date]:
Single Image
Copies
[Return]:
2
OK
Date
Return
OK :
Exit :
button.
2/3
Press the MENU button to return to the image playback mode.
* The
is marked on the displayed image.
5
To unmark the
DPOF
mark, go back to step 3 to select [Reset All] with or .
Single image
All Images
Reset All
OK :
Return :
Before you perform the DPOF settings on your camera, always remember to copy your images from the internal
memory to an SD memory card first.
The
print icon will appear on the monitor indicating images selected for printing.
You cannot print movies.
EN-49
Connecting to a PictBridge-Compatible Printer
Even if you do not have a computer, you can connect the camera directly to a printer that supports PictBridge
to perform image selection and printing using the camera monitor screen and controls. DPOF support also
lets you specify which images you want to print and how many copies of each should be printed.
Connecting the camera to the printer
1. Rotate the mode dial to
and turn your camera on by pressing
button.
the
2. Press to select the [Set-up2] menu, then use to select
button.
[USB Con.]. Press the
3. Use or to select [PictBridge], then press the
button.
4. Connect your camera and the printer via a supplied USB cable.
The screen turns off automatically and the setting screen will
appear on the monitor after 2 seconds.
USB Con.
PC
PictBridge
PC Camera
OK :
2/3
On Windows 98/98SE/ME/2000, if the camera is connected to your computer and you unintentionally set the camera's
USB connection to PictBridge, the "Install Driver" message will appear. Ignore this message and click "Cancel".
Printing images
When the camera is properly connected to a PictBridge-compatible printer, the [Select Printing Mode]
screen is displayed on the monitor. Use or to select the print mode.
In [Print] Mode: Lets you print the specified image with PictBridge.
Step
1
Figure
Procedure
Select Printing Mode
Print
Print w/DPOF setting
Select :
EN-50
OK :
Use or to select the [Print] mode, then press the
button.
Step
2
Procedure
Figure
Use or to access the paper selection setting, then press the
button to confirm.
[Paper Size]: You may select the desired item depending on the type of
printer being used.
[Borderless]:
You may select the desired item depending on the type
of printer being used.
[Cancel]:
To cancel the setting, use or to select [Cancel].
Paper Setting
Paper Size
Standard
Borderless
Standard
Cancel
Select :
OK :
100-0008
Use or to select the image you want to print, then press to set more
detailed settings.
3
Select :
Print :
Cancel :
Info. :
OK
Use or to select by your preference, then press the
[Copies] :
Print Setting
Copies
4
8
Date
With
File Name
With
[Date]:
[File Name]:
[Cancel]:
Cancel
Select :
OK :
100-0009
5
Select :
Print :
Cancel :
Info. :
button.
Specifies the number of prints. You can select the number
up to 10.
If you select [With], images are printed with the date.
If you select [With], images are printed with the file name.
To cancel the print settings, use or to select [Cancel].
After the step 4 is finished, you can still use or to change the image
by your preference, then press the
button to print.
OK
EN-51
Step
Figure
Procedure
Use or to select [Print], then press the
Print
button to confirm.
Print
6
Cancel
Total 2
Select :
OK :
This starts printing and displays the message “Printing now” on the monitor
screen.The message will disappear after the printing is finished.
Cancel :
7
* To cancel printing:
button during print data transfer displays the screen for
Pressing the
selecting whether to [Continue] or [Cancel] printing.
Print
Continue
Cancel
Select :
OK :
In [Print w/DPOF setting] Mode:
Step
Procedure
Figure
Select Printing Mode
Print
Print w/DPOF setting
1
Select :
EN-52
This function only lets you print the specified image based on
the previous DPOF settings.
OK :
Use or to select the [Print w/DPOF setting] mode, then press the
button.
Step
Procedure
Figure
Paper Setting
2
Paper Size
Standard
Borderless
Cancel
Standard
Select :
Use or to access the paper selection setting, then press the
button to print.
[Paper Size]: You may select the desired item depending on the type of
printer being used.
[Borderless]:
You may select the desired item depending on the type of
printer being used.
[Cancel]:
To cancel the setting, use or to select [Cancel].
OK :
Use or to select [Print], then press the
button to confirm.
Print
Print
Cancel
3
Total 2
Select :
OK :
This starts printing and displays the message “Printing now” on the monitor
screen. The message will disappear after the printing is finished.
Cancel :
4
* To cancel printing:
Print
Continue
button during print data transfer displays the screen for
Pressing the
selecting whether to [Continue] or [Cancel] printing.
Cancel
Select :
OK :
EN-53
TRANSFERRING FILES FROM YOUR DIGITAL
CAMERA TO COMPUTER
After using USB cable to establish a USB connection between the camera and your computer, you can use
your computer to share recorded images or movie clips with your family or friends via e-mail or post them on
the Web. In order to do this, you must install the USB driver onto your computer first. Note that before you
begin to install the software, you need to check your system according to the table as shown below.
System Requirements (Windows)
System Requirements (Macintosh)
CPU
Pentium III 600 MHz processor or higher
PowerPC G3/G4/G5
Operating System
Windows 98/98SE/ME/2000/XP
OS 9.2 or higher
RAM
32MB
(64MB RAM recommended)
32MB
(64MB RAM recommended)
Hard Disk Space
128MB hard disk space
128MB hard disk space
Required Devices
A CD-ROM drive
A CD-ROM drive
An available USB port
An available USB port
Display
EN-54
Color Monitor (800x600, 24-bit or higher
Color Monitor (800x600, 24-bit or
recommended)
higher recommended)
Step 1: Install the USB driver
Installation on Windows 98 & 98SE
The USB driver on the supplied CD-ROM (S-SW38) is exclusively for Windows 98 and 98SE. Windows
2000/ME/XP users don't need to install the USB driver.
1. Insert the enclosed CD-ROM (S-SW38) into your CD-ROM drive.
2. Connect the camera to the PC with the USB cable.
3. The "Add New Hardware Wizard" will appear on screen as shown
on the right. Click on "Next".
6
4. Select "Search for the best driver for your device". Click on "Next".
5. Select "CD-ROM drive" and "Specify a location" as shown on the
right. Click on "Next".
Follow the on-screen instructions to complete the installation.
6. After the USB driver has been installed, restart your computer.
Installation on MAC OS 9.2
For Mac OS 9.2 or higher, the computer will automatically recognize
the digital camera and load its own USB drivers.
EN-55
Step 2: Connect the digital camera to your computer
1. Rotate the mode dial to
and turn your camera on by pressing
the
button.
2. Press to select the [Set-up2] menu, then use to select [USB
Con.].
button.
3. Press the
Set-up1
USB
Set-up2
Set-up3
USB Con.
PC
Video Out
PAL
Brightness
0
Auto Power Off
OK :
2min
1/4
button.
4. Use to select [PC], then press the
5. Turn off your camera.
6. Connect your camera and the computer via a supplied USB
cable.
USB Con.
PC
PictBridge
PC Camera
OK :
EN-56
PC/AV terminal
DC IN 3.0V
button.
7. Turn your camera on by pressing the
8. There will be a new “Removable Disk” icon detected in “My
Computer”, which contains your recorded images or movie clips.
(For Mac users, double-click [untitled] or [unlabeled] disk drive
icon on our desktop.)
1/3
Step 3: Download images or movie clips
When the digital camera is turned on and connected to your computer, it is considered to be a disk drive,
just like a floppy disk or CD. You can download (transfer) images by copying them from the “Removable
disk” (“untitled” or “unlabeled” disk on a Macintosh) to your computer hard drive.
Windows
Open the “removable disk” and double click on the DCIM folder to open it to find more folders. Your
images are inside these folder(s). Select the desired still images or movie clips and then choose “Copy”
from the “Edit” menu. Open the destination location (folder) and choose “Paste” from the “Edit” menu.
You may also drag and drop image files from the digital camera to a desired location.
Macintosh
Open the “untitled” disk icon, and the destination location on your hard disk. Drag and drop from the
digital camera to the desired destination.
Memory card users may prefer to use a memory card reader (highly recommended).
Movie playback application is not included with the package. Make sure that movie playback application has
been installed in your computer.
EN-57
EDITING SOFTWARE INSTALLATION
Installing ACDSee for PENTAX
With ACDSee for PENTAX, you can find, organize, and preview images and media files on your
computer, and efficiently acquire images from digital cameras, scanners, and other devices. ACDSee
for PENTAX's full-featured image viewer and media player quickly generates high-quality displays of
your images and media files.
Also, ACDSee for PENTAX includes a wide variety of image editing tools you can use to create, edit,
and touch-up your digital images. Use tools such as red-eye reduction, crop, sharpen, blur, and emboss
to enhance or correct your images. Image management tools, such as exposure adjustment, convert,
resize, rename, and rotate, can be used to adjust multiple files at the same time.
1. Insert the enclosed CD-ROM (S-SW38) into your CD-ROM drive.
2. When the welcome screen appears, select "Application
Software".
3. Select the desired language.
Follow the on-screen instructions to complete the installation.
For more information about the operation of ACDSee for PENTAX
application software, refer to its respective help documentation.
For Windows 2000/XP users, please make sure to install and use the
ACDSee for PENTAX in “Administrator” mode.
EN-58
USING THE DIGITAL CAMERA AS A PC CAMERA
Your digital camera can act as a PC camera, which allows you to videoconference, or have a real-time
conversation with friends or family. To use the digital camera for videoconferencing, your computer
system must include the items as below:
Microphone
Sound card
Speakers or headphones
Network or Internet connection
Video conferencing (or video editing) software is not included with the digital camera.
This mode is not supported for Mac.
Step 1: Install the PC camera driver
The PC-camera driver included in the CD-ROM (S-SW38) is exclusively
for Windows. The PC camera function is not supported for Mac platforms.
1. Insert the enclosed CD-ROM (S-SW38) into your CD-ROM drive.
2. When the welcome screen appears, select "PC Camera Driver".
3. Select the desired language.
Follow the on-screen instructions to complete the installation.
4. After the driver installation is completed, restart your computer.
EN-59
Step 2: Connect the digital camera to your computer
1. Rotate the mode dial to
and turn your camera on by pressing
button.
the
2. Press to select the [Set-up2] menu, then use to select [USB
Con.].
button.
3. Press the
4. Use or to select [PC Camera], then press the
button.
5. Connect your camera and the computer via a supplied USB
cable.
6. Position the digital camera steadily on top of your computer
monitor or use a tripod.
USB Con.
PC
PictBridge
PC Camera
OK :
3/3
When using this digital camera as a PC camera, it is necessary to install the battery into the digital camera.
Step 3: Run your application software (i.e. Windows NetMeeting)
To use Windows NetMeeting for videoconferencing:
1. Go to Start Programs Accessories Communications NetMeeting to launch the NetMeeting
program.
2. Click the Start Video button to view live video.
3. Click the Place Call button.
4. Type the e-mail address or the network address of the computer that you are calling.
5. Click Call. The person that you are calling must also have Windows NetMeeting running and be
willing to accept your call to start the videoconference.
The video resolution for videoconferencing applications is generally 320 x 240.
For more information about the operation of videoconference application software, refer to its respective help
documentation.
EN-60
MENU OPTIONS
Camera Menu
This menu is for the basic settings to be used when capturing still images.
Simple
Mode1
Recorded pixels
6M
Mode2
Mode3
Recorded pixels
Mode1
Mode2
Mode3
Mode1
AE Metering
6M
Mode2
Mode3
Color
Quality Level
Quality Level
Sharpness
Medium
Drive Mode
White Balance
Auto
Digital Zoom
On
Saturation
Medium
Sensitivity
Auto
Instant Review
Off
Date Imprint
OK :
Exit :
1/3
OK :
Drive Mode
Exit :
0/4
OK :
Exit :
0/4
OK :
Off
Exit :
0/4
,
,
,
,
or and turn your camera on.
1. Rotate the mode dial to
2. Press the MENU button, then use or to select the [Mode1] / [Mode2] / [Mode3] menu.
Mode, press the MENU button to access the [Simple] menu directly.
In
3. Use or to select the option item, then press the
button.
4. Press or to select the desired setting, then press the
button.
In the
Item
Mode
Recorded pixels
Functional Description
Sets the size of the image that will be captured. (Refer to EN-25 for
further details.)
2848x2136
* 6
2272x1704
* 4
* 2
1600x1200
* 0.3 640x480
M
M
M
M
Quality Level
Sets the quality (compression rate) at which the image is captured.
Best
*
*
Better
*
Good
EN-61
Item
Drive Mode
Functional Description
Sets the recording method at the time of taking pictures. (Refer to EN35,36 for further details.)
In the
Mode1
EN-62
,
,
,
or
*
Standard
*
HS Continuous
*
Auto Bracket
Mode
Item
Functional Description
Recorded pixels Refer to the Camera Menu's option item (the
EN-61 for further details.)
Mode). (Refer to
Quality Level
Refer to the Camera Menu's option item (the
EN-61 for further details.)
Mode). (Refer to
White Balance
Sets the white balance when shooting under a variety of lighting
conditions and permits photographs to be taken that approach the
conditions that are seen by the human eye. (Refer to EN-31 for
further details.)
* [No icon] Auto
*
Daylight
Cloudy
*
*
Tungsten Light
*
Fluorescent Light
Sensitivity
Sets the sensitivity for taking pictures. When the sensitivity is raised (and
the ISO figure is increased), photography will become possible even in
dark locations, but the more pixilated (grainier) the image will appear.
*Auto / 64 / 100 / 200
Mode2
Item
AE Metering
Drive Mode
Functional Description
Refer to the section in this manual titled “Selecting the Metering
Mode”. (Refer to EN-37 for further details.)
Refer to the Camera Menu's option item (the
35, 36, 61 for further details.)
Mode). (Refer to EN-
Digital Zoom
This sets whether or not to use digital zoom at the time of shooting.
* On / Off
Instant Review
Set to display a photographed image on LCD monitor immediately
after you have taken the shot.
* On / Off
EN-63
Mode3
Item
Color
Sharpness
Saturation
Functional Description
Sets the color of the image that will be captured.
*
Full Color
*
B&W
*
Sepia
Sets the level of image sharpness.
*
High
*
Medium
*
Low
To capture an image, your camera offers you three different degrees
of color to match with your preference.
Your images will demonstrate different impression by selecting
different degrees of color. This is called “Saturation”.
High
*
Medium
*
*
Low
Date Imprint
The date of recording can be printed directly on the still images. This
function must be activated before the image is captured. The date
appears on the right bottom of the captured picture. When images
are shot with date imprint feature, the date cannot be removed later.
* On / Off
01/07/2005
EN-64
Movie Menu
This menu is for the basic settings to be used when recording movie clips.
Movie
Color
Digital Zoom
OK :
On
Exit :
1. Rotate the mode dial to
1/2
and turn your camera on.
2. Press the MENU button.
3. Use or to select the option item, then press the
button.
4. Use or to select the desired setting, and press the
button.
5. To exit the movie menu, press the MENU button.
Item
Color
Functional Description
Refer to the Camera Menu's option item (the
64 for further details.)
,
,
,
or
Mode). (Refer to EN-
Digital Zoom Refer to the Camera Menu's option item (the
63 for further details.)
,
,
,
or
Mode). (Refer to EN-
EN-65
Playback Menu
In the
menu, set which settings are to be used for playback.
PlayBack1
PlayBack2
PlayBack1
Slideshow
Resize
Protect
Quality Change
DPOF
OK :
PlayBack2
Image Copy
Exit :
0/3
OK :
Exit :
0/3
button.
1. Press the
The last recorded image appears on the LCD monitor.
2. Press the MENU button, then use or to select the [PlayBack1] / [PlayBack2] menu.
3. Use or to select the option item, then press the
button.
4. Use or to select the desired setting, and press the
button.
5. To exit the playback menu, press the MENU button.
[PlayBack1] settings
Item
Functional Description
Slideshow
Protect
DPOF
EN-66
You can play back recorded images in order with a selected interval time.
This function is useful for checking your images or for presentations, etc.
Refer to the section in this manual titled “Slideshow Display”. (Refer to EN-41 for
further details.)
* 3 sec. / 5 sec. / 10 sec.
Set the data to read-only to prevent images from being erased by mistake.
Refer to the section in this manual titled “Protecting Images/Movie clips”. (Refer to EN-47
for further details.)
Allows you to select the desired pictures to be printed and set the number of prints
and date displayed in DPOF format. You can print images easily just by inserting the
memory card to a DPOF-compatible printer or taking it to a print shop. Refer to the
section in this manual titled “Setting the DPOF”. (Refer to EN-48 for further details.)
[PlayBack2] settings
Item
Functional Description
Resize
Changes the size of a recorded image.
Resizing replaces the original image with the changed image. Only resizing to the
smaller size is available. (Refer to EN-42 for further details.)
* 6
M
2848x2136
* 4
M
2272x1704
*
2M
1600x1200
*
0.3
M
640x480
Quality Change Change the quality (compression rate) of a recoded image.
Compresses images down to half of their size or more, overwrites an old size images
with a newly compressed image. Only quality changing to the lower quality level is
available.
Image Copy
*
Best
*
Better
*
Good
Allows you to copy your files from the digital camera’s internal memory to a memory
card. Of course, you can only do this if you have a memory card installed and some
files in internal memory.
* OK / Cancel
EN-67
Setup Menu
This feature allows you to set up the default settings by preference for using your camera.
Set-up1
Set-up2
Set-up3
Sound
Date Adjust
Language
OK :
Set-up1
Set-up2
Set-up3
USB Con.
PC
Off
Video Out
PAL
d/m/y
Brightness
0
USB
Format
Auto Power Off
English
0/4
Set-up1
Set-up3
Reset
Ver.
Version
2min
OK :
0/4
mode and turn your camera on.
1. Rotate the mode dial to
2. Press or to select the [Set-up1] / [Set-up2] / [Set-up3] menu.
button.
3. Use or to select the option item, then press the
4. Use or to select the desired setting, and press the
button.
5. To exit the setup menu, rotate the mode dial to another mode.
EN-68
Set-up2
Reset No.
OK :
0/3
[Set-up1] settings
Item
Format
Sound
Date Adjust
Language
Functional Description
Erases all images and reformats the SD card loaded in your camera. Protected
images are also erased. SD card cannot be formatted if it is write-protected.
Refer to the section in this manual titled “Formatting an SD Memory Card or Internal
Memory”. (Refer to EN-22 for further details.)
* OK / Cancel
This sets whether or not to mute the startup sound, and the camera sound each
time you press a camera button.
* Loud / Soft / Off
This sets the date and the time.
Refer to the section in this manual titled “Setting the Date and Time”. (Refer to EN21 for further details.)
* y/m/d
* d/m/y
* m/d/y
Sets the language that is displayed on the LCD monitor.
Refer to the section in this manual titled “Choosing the Screen Language”. (Refer to
EN-20 for further details.)
* English / Français / Deutsch / Español / Italiano / Svenska / Nederlands /
EN-69
[Set-up2] settings
Item
Functional Description
USB Connection Selects to choose one of the following modes for further settings. (Refer to EN-50,
56, 60 for further details.)
* PC / PictBridge / PC Camera
Video Out
Sets video output of the camera for matching the video output system of the
equipment that you are going to connect to the camera.
* PAL / NTSC
Brightness
This sets the brightness of the LCD monitor.
The adjustment range is from -5 to +5.
Auto Power Off
If no operation is performed for a specific period of time, the power to the camera
is automatically turned off. This feature is useful to reduce battery wear.
* 2 min. / 3 min. / 5 min. / Off
[Set-up3] settings
Item
Reset No.
Functional Description
Sets whether or not to reset the file number when you take photographs. This
creates a new folder. The captured images are recorded to the newly created
folder from number 0001. If you want to reset the file number, be sure that no
images are recorded in the internal memory or the SD memory card.
* OK / Cancel
Reset
Returns all basic settings to the digital camera’s default settings. The time setting
will not be reset.
* OK / Cancel
Version
This displays the current firmware version of the camera.
Ver.
EN-70
CONNECTING THE DIGITAL CAMERA TO OTHER
DEVICES
EN-71
SPECIFICATIONS
Item
Image Sensor
Effective pixels
Image size
Description
CCD
6.0 Mega pixels
Still image: 2848 x 2136, 2272 x 1704, 1600 x 1200, 640 x 480
Movie clip: 320 x 240
Image quality
Still image: Best, Better, Good
Movie image: Good
Recording media
Approx. 12MB internal memory
SD memory card (Optional, up to 1GB)
File format
Motion JPEG (AVI); PictBridge support;
PC-CAM support (QVGA around 24 f/s)
Lens
F-no.: Wide: 2.8 / Tele: 4.8
Focal length: 7.5mm-22.5mm (Equivalent to 35mm Camera: 36~108 mm)
Focus range
Normal : 0.5 m to infinity
Macro : 0.05 m to infinity (Wide)
: 0.3 m to infinity (Tele)
Flash effective range Wide: Approx. 0.5 m - Approx. 3.8 m (at the standard output sensitivity of 200)
Tele: Approx. 0.5 m - Approx. 2.0 m (at the standard output sensitivity of 200)
LCD monitor
2.0” TLT color LCD
High-resolution 130K pixels display
Self-timer
10 sec delay, 2 sec delay, 10+2 sec delay
Exposure compensation -2.0EV~ +2.0EV (in 0.3EV increments)
White balance
Auto, Daylight, Cloudy, Tungsten, Fluorescent
ISO
Auto, 64, 100, 200
Interface
DC-IN jack, USB/AV terminal
Power
2 x AA (alkaline or Ni-MH rechargeable) batteries
(Two alkaline batteries allow approximately 80 shots to be taken*)
(Two Ni-MH rechargeable batteries (2500mAh) allow approximately 270 shots
to be taken*)
AC-DC Adapter (3V/2.5A) (Optional)
Dimension
Approx. 91 x 61 x 38 mm
Weight
Approx. 150g (without batteries and the SD memory card)
*
Recording capacity shows approximate number of shots recorded during CIPA-compliant testing. Actual performance
may vary according to operating conditions.
Design and specifications are subject to change without notice.
EN-72
APPENDIX
Troubleshooting Guide
Symptom
Possible causes
Power does not
turn on.
*
*
*
*
Camera suddenly
powers down.
* The function of [Auto Off] in the
has been activated.
* The battery has run out.
Image is not captured
when the shutter
button is pressed.
* The camera is in the
Flash does not fire.
Continuous shooting
is not possible.
Cannot transfer files
over a USB connection.
The battery has run out.
The battery is not oriented correctly.
The battery cover is not closed properly.
The AC power adapter (optional)
is disconnected.
or
mode
mode.
* Memory is full.
Solutions / Corrective Actions
* Load new or fully charged battery.
* Load the battery in the correct direction.
* Close the battery cover correctly.
* Properly connect the AC power
adapter.
* Turn the power back on and set the
option of [Auto Off] to [Off].
* Load new or fully charged battery.
,
,
,
* Rotate the mode dial to
,
or .
* Transfer the desired files to your
computer and then delete unnecessary
files, or use a different memory card.
* Flash off is selected in flash mode.
* Select a different flash mode.
* The [Drive Mode] is set to [HS Continuous] * Select [Standard ] in the [Drive Mode].
or [Auto Bracket].
(movie) mode.
* The camera is in the
* The capacity of the built-in memory or
SD memory card is full.
* Switch the mode dial to another mode.
* Insert a new SD memory card.
* USB cable is not connected securely.
* USB driver is not installed.
* Camera is turned off.
* Check all connections.
* Install the USB driver on your computer.
* Turn on the camera.
EN-73
Possible Number of Recordable Images
The frame counter indicates the approximate number of images that can be stored on the internal
memory and the SD memory card. The number of recordable images may vary depending on the
recorded subject, the capacity of the memory card, if there are files other than images or when the
recording is made while switching the picture quality or resolution.
Resolution
2848 x 2136
6M
2272 x 1704
4M
1600 x 1200
2M
640 x 480
0.3
M
Quality
(Compression
Ratio)
Best (1/4)
Better (1/8)
Good (1/16)
Best (1/4)
Better(1/8)
Good (1/16)
Best (1/4)
Better (1/8)
Good (1/16)
Best (1/4)
Better (1/8)
Good (1/16)
SD Memory Card
Internal
Memory
32MB
64MB
128MB
256MB
512MB
1GB
3
7
14
5
11
22
10
21
42
63
127
254
8
17
35
13
27
55
26
53
106
166
333
667
18
36
73
28
56
113
54
107
215
322
645
1291
36
73
147
57
115
230
110
217
435
652
1305
2610
73
147
294
114
229
458
219
433
866
1300
2600
5201
148
296
593
231
462
924
442
873
1724
2620
5240
10480
285
570
1140
444
889
1778
851
1679
3358
5038
10076
20152
The above data shows the standard testing results. The actual capacity varies according to the
shooting conditions and settings.
EN-74
Approximate Duration of Recording Time
The table below indicates the approximate duration of recording time depending on the capacity of the
internal memory and the SD memory card.
SD Memory Card
Image size
Internal Memory
320 x 240
00:55
32MB
64MB
128MB
256MB
02:19
04:47
09:42
19:20
512MB
39:00
1GB
1:15:01
The values for the recording time may vary depending on the shooting conditions and settings.
EN-75
WARRANTY POLICY
All PENTAX cameras purchased through authorized bona fide photographic distribution channels are
guaranteed against defects of material or workmanship for a period of twelve months from date of
purchase. Service will be rendered, and defective parts will be replaced without cost to you within that
period, provided the equipment does not show evidence of impact, sand or liquid damage,
mishandling, tampering, battery or chemical corrosion, operation contrary to operating instructions, or
modification by an unauthorized repair shop. The manufacturer or its authorized representatives shall
not be liable for any repair or alterations except those made with its written consent and shall not be
liable for damages from delay or loss of use or from other indirect or consequential damages of any
kind, whether caused by defective material or workmanship or otherwise; and it is expressly agreed
that the liability of the manufacturer or its representatives under all guarantees or warranties, whether
expressed or implied, is strictly limited to the replacement of parts as hereinbefore provided. No
refunds will be made on repairs by non-authorized PENTAX service facilities.
Procedure during 12-month Warranty Period
Any PENTAX which proves defective during the 12-month warranty period should be returned to the
dealer from whom you purchased the equipment or to the manufacturer. If there is no representative of
the manufacturer in your country, send the equipment to the manufacturer, with postage prepaid. In this
case, it will take a considerable length of time before the equipment can be returned to you owing to
the complicated customs procedures required. If the equipment is covered by warranty, repairs will be
made and parts replaced free of charge, and the equipment will be returned to you upon completion of
servicing. If the equipment is not covered by warranty, regular charges of the manufacturer or of
its representatives will apply. Shipping charges are to be borne by the owner.
EN-76
If your PENTAX was purchased outside of the country where you wish to have it serviced during the
warranty period, regular handling and servicing fees may be charged by the manufacturer’s representatives
in that country. Notwithstanding this, your PENTAX returned to the manufacturer will be serviced free of
charge according to this procedure and warranty policy. In any case, however, shipping charges and
customs clearance fees to be borne by the sender. To prove the date of your purchase when required,
please keep the receipt or bills covering the purchase of your equipment for at least a year. Before
sending your equipment for servicing, please make sure that you are sending it to the manufacturer’s
authorized representatives or their approved repair shops, unless you are sending it directly to the
manufacturer. Always obtain a quotation for the service charge, and only after you accept the quoted
service charge, instruct the service station to proceed with the servicing.
* This warranty policy does not affect the customer’s statutory rights.
* The local warranty policies available from PENTAX distributors in some countries can
supersede this warranty policy. Therefore, we recommend that you review the warranty
card supplied with your product at the time of purchase, or contact the PENTAX distributor
in your country for more information and to receive a copy of the warranty policy.
The CE Mark is a Directive conformity mark of the European Union.
EN-77
Declaration of Conformity
According to 47CFR, Parts 2 and 15 for
Class B Personal Computers and Peripherals
We:
PENTAX IMAGING COMPANY
A Division of PENTAX of America, Inc.
Located at:
600 12 Street, Suite 300
Golden, Colorado 80401 U.S.A.
Phone: 303-799-8000 FAX: 303-790-1131
Declare under sole responsibility that the product identified herein, complies with 47CFR Parts 2 and 15
of the FCC rules as a Class B digital device. Each product marketed is identical to the representative unit
tested and found to be compliant with the standards.
Records maintained continue to reflect the equipment being produced can be expected to be within the
variation accepted, due to quantity production and testing on the statistical basis as required by 47CFR
§2.909. Operation is subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) This device must accept any interference received, including interference that may
cause undesired operation. The above named party is responsible for ensuring that the equipment
complies with the standards of 47CFR §15.101 to §15.109.
Product Name: PENTAX Digital Still Camera
Model Number: Optio 60
Contact person: Customer Service Manager
Date and Place: July, 2005, Colorado
EN-78
An information on Disposal for users
1. In the European Union
If your product is marked with this symbol, it means that used electrical/electronic
products should not be mixed with general household waste. There exists a separate
collection system for these products.
Used electric/electronic equipment must be treated separately and in accordance with
legislation that requires proper treatment, recovery and recycling of these products.
Following the implementation by member states, private households within the EU states
may return their used electrical/electronic equipments to designated collection facilities
free of charge*. In some countries your local retailer may also take back your old product
free of charge if you purchase a similar new one.
*Please contact your local authority for further details.
By disposing of this product correctly you will help ensure that the waste undergoes the
necessary treatment, recovery and recycling and thus prevent potential negative effects
on the environment and human health which could otherwise arise due to inappropriate
waste handling.
2. In other countries outside the EU
If you wish to discard this product, please contact your local authorities and ask for the
correct method of disposal.
For Switzerland: Used electrical/electronic equipment can be returned free of charge to
the dealer, even when you don’t purchase a new product. Further collection facilities are
listed on the home page of www.swico.ch or www.sens.ch.
EN-79
">