Palo Alto Networks M-100 Appliance Hardware Reference Guide
Below you will find brief information for Appliance M-100. The M-100 is a multi-function appliance that can be configured as either a dedicated log collector or a central management system. It provides the ability to manage and collect logs from multiple Palo Alto Networks firewalls, simplifying security operations.
Advertisement
Advertisement
M-100 Appliance
Hardware Reference Guide
Contact Information http://www.paloaltonetworks.com/contact/contact/
About this Guide
This guide describes the M-100 appliance, provides instructions on installing the hardware and performing maintenance procedures, and provides product specifications. This guide is intended for system administrators responsible for installing and maintaining the M-100.
All M-100 devices run Panorama, a purpose-built operating system with extensive functionality. Please refer to the Palo Alto Networks Panorama Administrator’s Guide for information on using Panorama.
• For information on the additional capabilities and for instructions on configuring the features on the firewall, refer to https://www.paloaltonetworks.com/documentation.
• For access to the knowledge base, complete documentation set, discussion forums, and videos, refer to https://live.paloaltonetworks.com.
• For contacting support, for information on the support programs, or to manage your account or devices, refer to https://support.paloaltonetworks.com.
• For the latest release notes, go to the software downloads page at
https://support.paloaltonetworks.com/Updates/SoftwareUpdates .
To provide feedback on the documentation, please write to us at:
[email protected].
Palo Alto Networks, Inc.
www.paloaltonetworks.com
© 2007–2016 Palo Alto Networks, Inc. Palo Alto Networks is a registered trademark of Palo Alto Networks. A list of our trademarks can be found at http://www.paloaltonetworks.com/company/trademarks.html
. All other marks mentioned herein may be trademarks of their respective companies.
Revision Date: September 2, 2016
September 2, 2016 - Palo Alto Networks COMPANY CONFIDENTIAL
Table of Contents
10
Connecting Cables to the Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15
16
Service the Hardware. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
17
17
Replace an M-100 Appliance Disk Drive . . . . . . . . . . . . . . . . . . . . . . . . . . .
18
22
23
23
24
24
24
Compliance Statements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
25
25
26
Palo Alto Networks Table of Contents • 3
General Safety Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
27
Other Regulatory Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
29
4 • Table of Contents Palo Alto Networks
Chapter 1
Overview
The Palo Alto Networks M-100 appliance is a multi-function appliance that you can configure for one of the following two modes:
• Panorama mode —Performs both central management and log collection for Palo Alto
Networks firewalls. This is the default mode.
• Log Collector mode —Functions as a dedicated Log Collector, which either an M-100 or
M-500 appliance in Panorama mode or a Panorama virtual appliance can manage.
Note: The minimum Panorama version that you can install on a M-500 appliance is 7.0.
Use the following topics to learn about the front and back panel components.
•
“Front Panel” in the next section
•
Palo Alto Networks Overview • 5
Front Panel
Front Panel
Figure 1 shows the front panel of the M-100 appliance and Table 1 describes the front panel
features.
M-100
1
2
3
4
5
6
7
A1 / A2 B1 / B2 C1 / C2 D1 / D2
8
Figure 1. Front Panel
9 10 11
Table 1. Front Panel Features
Item Description
1) Disk Drives/Bays
2) System Health
3) Internal HDD Activity
4) LAN Activity
5) UID Button (LED)
6) Power Button/LED
The M-100 has 8 disk drive bays. Starting from left to right, the bays are labeled A1/A2, B1/B2 C1/C2, and D1/D2.
Indicates overall system health. Green indicates healthy, red indicates a system error.
Blinks if there is disk drive activity.
Blinks if there is network activity.
The Unique Identification (UID) feature is a combination LED/button that is used to assist a technician in locating a device when moving from the back of a rack to the front of a rack. When you push the button, the rear
UID LED and the front panel LEDs will illuminate bright blue, assisting the technician in identifying the device in a rack. Push the button again to stop the LED from flashing.
Note that the UID button is very small and is located slightly to the left of the UID port hole. Use a small object, such as a paper clip, to press the button.
Used to power on and off the M-100 device. To power off the system, hold
down the button until the system shuts down.
Note: When the system in initially plugged in, it will automatically power on.
7) NMI Button The Non-Maskable Interrupt button is currently disabled on the M-100 device.
8)Drive LEDs
9) Console
• Top LED — Blinks green when there is drive activity.
• Right LED —Illuminates red when a drive failure occurs.
DB-9 serial port for console access.
6 • Overview Palo Alto Networks
Front Panel
Table 1. Front Panel Features (Continued)
Item Description
10) MGT
11) 1
RJ-45 10/100/1000 management port used for management, log collection, and log collector to log collector communication.
RJ-45 10/100/1000 Ethernet Port 1 used for log collection and collector group communication. You can configure ports 1 and 2 to perform one or both of these functions, but you cannot configure both ports to perform the same function.
Palo Alto Networks Overview • 7
Back Panel
Back Panel
Figure 2 shows the back panel of the M-100 and Table 2 describes the back panel features.
1 2 3
4
UID
5
Figure 2. Back Panel
Table 2. Back Panel Features
Item Description
1) Power Port
2) 2
AC power inlet.
RJ-45 10/100/1000 Ethernet Port 2 used for log collection and collector group communication. You can configure ports 1 and 2 to perform one or both of these functions, but you cannot configure both ports to perform the same function.
Note: This port functionality is available in version 6.1 and later. Prior to
6.1, this port is not functional.
3) 3
4) USB Ports
5) UID Button
RJ-45 10/100/1000 Ethernet Port 3. (Reserved for future use)
USB ports for future use.
The Unique Identification feature is a combination LED/button that is used to assist a technician in determining which device is being worked on when moving from the front of a rack to the back of a rack. When the button is pushed (either front or rear), both the front and rear UID LEDs will flash blue, assisting the technician in identifying the device in a rack. When either button is pushed again, the flashing LEDs stop flashing.
8 • Overview Palo Alto Networks
Tamper Proof Statement
Chapter 2
Installing the Hardware
This chapter describes how to install the M-100. For more information, refer to the following topics:
•
“Tamper Proof Statement” on page 9
•
“Before You Begin” in the next section
•
“Equipment Rack Installation” on page 10
•
“Connecting Cables to the Device” on page 15
•
Tamper Proof Statement
To ensure that products purchased from Palo Alto Networks have not been tampered with during shipping, verify the following upon receipt of each product:
• The tracking number provided to you electronically when ordering the product matches the tracking number that is physically labeled on the box or crate.
• The integrity of the tamper-proof tape used to seal the box or crate has not been compromised.
• The warranty seals on the device itself do not show evidence of tampering.
Before You Begin
• It is recommended that two people be available to mount the M-100 in a 19-inch rack.
• Have a Phillips head screwdriver available and a small pliers or nut wrench.
• Verify that the intended location has adequate air circulation and meets the temperature
requirements. Refer “Environmental Specifications” on page 24.
• Unpack the device.
• Verify that power is not connected to the appliance.
• Allow clear space on both sides of the appliance.
Palo Alto Networks Installing the Hardware • 9
Equipment Rack Installation
Equipment Rack Installation
The M-100 rack mount kit is ordered separately and can be used to mount the M-100 on a 2post or 4-post 19” rack.
The following safety guidelines apply to rack installation:
• Elevated ambient operating temperature —If the M-100 is installed in a closed or multiunit rack assembly, the ambient operating temperature of the rack environment may be greater than the ambient room temperature. Verify that the ambient temperature of the rack assembly meets the maximum rated ambient temperature requirements listed in
“Environmental Specifications” on page 24.
• Reduced air flow —Ensure that the airflow required for safe device operation is not compromised by the rack installation.
• Mechanical loading —Ensure that the rack-mounted device does not cause hazardous conditions due to uneven mechanical loading.
• Circuit overloading —Ensure that the circuit that supplies power to the device is sufficiently rated to avoid circuit overloading or excess load on supply wiring. Refer to
“Electrical Specifications” on page 24.
• Reliable earthing —Maintain reliable earthing of rack mounted equipment. Pay special attention to supply connections other than direct connections to the branch circuit (such as the use of power strips).
To install the M-100 in a grounded 19-inch rack:
10 • Installing the Hardware Palo Alto Networks
Equipment Rack Installation
1.
Unpack the rail kit and then remove the inner rail from the outer rail and attached the inner rail to both sides of the M-100. To do this, place the inner rail over the mounting posts and then slide forward to lock in place. The mounting screw holes will be exposed at which time you can use the provided screws to secure the inner rail to the M-100 as
Figure 3. Attaching the Inner Rail to the M-100
Press the latch to disconnect the inner rail from the outer rail.
1
2
2
Attach the inner rail on both sides of the M-100.
Palo Alto Networks Installing the Hardware • 11
Equipment Rack Installation
2.
If this is a 4-post rack install, continue to Step 3. If this is a 2-post install, attached the 2-
post brackets to the outer rail as shown in Figure 4.
Figure 4. Attaching the 2-post Bracket for 2-post Rack Installation
Bracket for 2-post installation.
Bracket for 2-post installation.
12 • Installing the Hardware Palo Alto Networks
Equipment Rack Installation
3.
Attach the outer rail to the rack. The 2-post install will use the two inner mounting brackets to attach to the rack and the 4-post install will use the two outer brackets. Both
install methods are shown in Figure 5.
Note: If you are using a non-threaded rack, install the threaded brackets behind
each rack mount point as shown in Figure 5.
Figure 5. Installing the Outer Rail on a 2-post and 4-post Rack
2-post
Install
4-post
Install
Two threaded mounting brackets for non-threaded racks.
Two threaded mounting brackets for non-threaded racks.
Palo Alto Networks Installing the Hardware • 13
Equipment Rack Installation
4.
Lift the M-100 in place and align the inner rail that is mounted on the M-100 with the outer rail that is now mounted on the rack and slide the M-100 into place. The illustration
in Figure 6 shows the M-100 being installed in a 2-post and 4-post rack.
Figure 6. Installing the M-100 Into a 2-post or 4-post Rack
2-post Rack
4-post Rack
14 • Installing the Hardware Palo Alto Networks
Connecting Cables to the Device
5.
Tighten the thumb screws on the front of the M-100 to secure it to the rail as shown in
Figure 7. It is recommended that you tighten the thumb screws with a Phillips head or
flat-head screwdriver after tightening by hand.
Figure 7. Tightening the Thumb Screws on the M-100.
Connecting Cables to the Device
Figure 8 shows the front M-100 cable connections. Refer to Table 1 for descriptions of the front
panel interfaces and Table 2 for descriptions of the back panel interfaces.
CAUTION: Shielded interface cables which are grounded shall be used to ensure agency compliance with electromagnetic emissions (EMC).
Figure 8. Cable Connections for the Front of the M-100
Front
A1 / A2 B1 / B2 C1 / C2 D1 / D2
Palo Alto Networks
Serial
Console Management
Installing the Hardware • 15
Connecting Power
Connecting Power
To power the M-100, attach a power cable to the device and plug it into a grounded wall outlet. The device will power on automatically.
16 • Installing the Hardware Palo Alto Networks
Cautions and Warnings
Chapter 3
Service the Hardware
This chapter describes how to replace disk drives, interpret LEDs, and troubleshoot hardware problems. For more information, refer to the following topics:
•
“Cautions and Warnings” in the next section
•
“Replace an M-100 Appliance Disk Drive” on page 18
•
“Interpreting the Port LEDs” on page 22
Cautions and Warnings
CAUTION: Disconnect all power cords before servicing the M-100.
WARNING: Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the battery manufacturer’s instructions.
WARNING: Removal of the equipment’s top cover is to be done only by Palo Alto Networks trained service person(s).
Palo Alto Networks Service the Hardware • 17
Replace an M-100 Appliance Disk Drive
Replace an M-100 Appliance Disk Drive
The M-100 appliance has eight drive bays and each drive pair (A1 and A2 and B1 and B2 for example) is in a separate RAID 1 array. This configuration provides redundancy so if a disk drive in a RAID 1 array fails there is no service interruption or loss of log data.
For information on how to increase log storage capacity, refer to the Panorama
Administrator’s Guide version 7.1 or later located on the Technical Documentation Portal .
CAUTION: Do not attempt to replace a drive with a third-party drive. Also, do not mix drive models within a RAID 1 array (for example, the drive model must be the same for both drives in the A1/A2 RAID 1 array). You can, however, mix drive models in different RAID 1 arrays. For example, the drives in the A1/A2 array can both be model
ST91000640NS and the drives in the B1/B2 array can both be model ST1000NX0423.
1.
Place an anti-static wrist strap around your wrist and connect it to ground.
2.
Identify the failed drive and note the drive model by running the following operational command and viewing the status and model fields: admin@M-100> show system raid detail
For example, the following output shows that disk drive A2 failed and the drive model is
ST91000640NS.
Disk Pair A Available
Status clean, degraded
Disk id A1 Present
model : ST91000640NS
size : 953869 MB
status : active sync
Disk id A2 Present
model : ST91000640NS
size : 953869 MB
status : failed
3.
Remove the failed drive from the RAID 1 array. In this example, run the following command to remove drive A2 from the array: admin@M-100> request system raid remove A2
18 • Service the Hardware Palo Alto Networks
Replace an M-100 Appliance Disk Drive
4.
Press the ejector button on the carrier of the failed drive (A2 in this example) to release the carrier handle and gently pull the handle toward you and slide the carrier out of the
appliance. Figure 9 shows how to remove a drive carrier (A1 in the illustration) from the
appliance.
Figure 9. Remove or Install an M-100 Appliance Disk Drive Carrier
5.
Remove the replacement drive from the packaging and compare the drive model written on the label with the drive model of the failed drive. Proceed as follows based on your findings:
– If the replacement drive is the same model number of the failed drive that you
removed, then continue to Step 6.
– If the replacement drive is a different model number than the drive that you removed,
6.
Install a replacement disk drive that is the same model as the other drive in the RAID 1 array:
Palo Alto Networks Service the Hardware • 19
Replace an M-100 Appliance Disk Drive a.
Remove the four screws that hold the failed drive in the drive carrier and then remove the drive from the carrier.
Note: If you are using an empty carrier that does not have a drive installed, you may have to remove the blank drive insert by removing the four screws that attach the insert to the carrier.
b.
Put the new drive in the carrier and secure it to the carrier using the four screws you removed from the failed drive.
c.
Ensure that the drive carrier lever is in the open position; if it is not, press the ejector button on the drive carrier to release the lever and pull it out until it is fully open.
d.
Slide the drive and carrier assembly into the drive bay on the appliance until it is about
1/4” from being fully inserted. You can do this by pressing the ejector button on the carrier which will cause the lever to close part way. After the drive is almost fully inserted, close the lever to seat the drive in place.
e.
Add the replacement drive to the RAID 1 array. In this example, run the following command to add drive A2 to the array: admin@M-100> request system raid add A2
The system will automatically configure the new drive to mirror the other drive in the
RAID 1 array.
f.
Continue to view RAID status until you see that the disk pair (Disk Pair A in this example) shows Available and both drives show the status active sync. To view
RAID status, run the following command: admin@M-100> show system raid detail
The following output shows that the RAID 1 array is functioning properly:
Disk Pair A Available
Status clean
Disk id A1 Present
model : ST91000640NS
size : 953869 MB
status : active sync
Disk id A2 Present
model : ST91000640NS
size : 953869 MB
status : active sync
7.
Install a replacement disk drive that is a different model than the other drive in the
RAID 1 array:
Note: When you initiate the copy command as described in the following steps, logging and log query will not be available on the disk pair until the copy is complete and the disk pair shows Available. If the other drive pairs (B1/B2, C1/
C2, and D1/D2 in this example) are low on disk during the copy process, older logs are deleted to make room for new logs.
a.
Remove the four screws that hold the drive in the drive carrier and then remove the failed drive (A2 in this example) from the carrier.
Note: If you are using an empty carrier that does not have a drive installed, you may have to remove the blank drive insert by removing the four screws that attach the insert to the carrier.
20 • Service the Hardware Palo Alto Networks
Replace an M-100 Appliance Disk Drive b.
Put the new drive in the carrier and attach it to the carrier using the four screws you removed from the failed drive.
c.
Ensure that the drive carrier lever is in the open position; if it is not, press the ejector button on the drive carrier to release the lever and pull it out until it is fully open.
d.
Slide the drive carrier into the drive bay on the appliance until it is about 1/4” from being fully inserted. You can do this by pushing on the ejector button which will cause the lever to close part way. After the carrier is almost fully inserted, close the lever to seat the drive in place.
e.
Copy the data from the existing drive in the RAID 1 array to the replacement drive. In this example, run the following command to copy the data from drive A1 to drive A2: admin@M-100> request system raid copy from A1 to A2 f.
Run the following CLI command to view the status of the copy:
admin@M-100> show system raid detail
Continue to view RAID status until the copy is complete and the disk pair shows
Available . In this example, the output shows that Disk Pair A is Available.
Note: At this point, drive A1 will show not in use because there is a drive model mismatch.
Palo Alto Networks
Disk Pair A Available
Status clean, degraded
Disk id A1 Present
model : ST91000640NS
size : 953869 MB
status : not in use
Disk id A2 Present
model : ST1000NX0423
size : 953869 MB
status : active sync g.
Install the second replacement drive. In this example, physically remove the drive from bay A1, install it in the carrier, and then install the second replacement drive— one that is the same model as you installed in bay A2—into bay A1.
h.
Add the second replacement drive to the RAID 1 array. In this example, run the following command to add drive A1 to the array: admin@M-100> request system raid add A1
The system will automatically configure the new drive to mirror the other drive (A2 in this example) in the RAID 1 array.
i.
Continue to view the RAID status until you see that the disk pair (Disk Pair A in this example) shows Available and both drives show the status active sync. admin@M-100> show system raid detail
The following output shows that the RAID 1 array is functioning properly:
Disk Pair A Available
Status clean
Disk id A1 Present
model : ST1000NX0423
size : 953869 MB
status : active sync
Disk id A2 Present
model : ST1000NX0423
size : 953869 MB
status : active sync
Service the Hardware • 21
Interpreting the Port LEDs
Interpreting the Port LEDs
Each Ethernet port on the M-100 has two LEDs. Table 3 describes the LEDs.
Table 3. Port LEDs
LED Description
Left
Right
Shows green if there is a network link.
Blinks if there is network activity.
22 • Service the Hardware Palo Alto Networks
Physical Specifications
Chapter 4
Specifications
This chapter provides specifications for the M-100. For more information, refer to the following topics:
•
“Physical Specifications” in the next section
•
“Interface Specifications” on page 24
•
“Electrical Specifications” on page 24
•
“Environmental Specifications” on page 24
Physical Specifications
Table 4 lists the physical specifications for the M-100.
Table 4. Physical Specifications
Specification Description
Height
Depth
Width
Weight
Mounting
Fans
1.75 inches (1 RU).
23 inches.
17.2 inches.
26.7 lb
Standard 19-inch rack.
Four fans.
Palo Alto Networks Specifications • 23
Interface Specifications
Interface Specifications
Table 5 describes the interfaces for the M-100.
Table 5. Interface Specifications
Specification Description
Ethernet ports
MGT port
Console port
USB ports
3 x RJ-45 10/100/1000 ports for network traffic. (Port 3 is reserved for future use)
1 RJ-45 Ethernet port
1 DB-9 serial port for connecting a serial console. Use these settings:
• Data rate: 9600
• Data bits: 8
• Parity: none
• Stop bits: 1
• Flow control: none
4 USB port for future use.
Electrical Specifications
Table 6 lists the electrical specifications for the M-100.
Table 6. Electrical Specifications
Specification
Maximum internal power dissipation
AC voltage
Description
500W
100-240 VAC
Environmental Specifications
Table 7 lists the environmental specifications for the M-100.
Table 7. Environmental Specifications
Specification Description
Operating temperature range 5° to 40° C
Storage temperature range -40° to 65° C
System air flow
Operating humidity
Storage humidity
Front to rear
10% to 80% non-condensing
5% to 95% non-condensing
24 • Specifications Palo Alto Networks
VCCI Statement
Chapter 5
Compliance Statements
This topic lists the M-100 appliance hardware compliance statements.
•
•
VCCI Statement
This section provides the compliance statement for the Voluntary Control Council for
Interference by Information Technology Equipment (VCCI), which governs radio frequency emissions in Japan.
The following information is in accordance to VCCI Class A requirements:
Translation: This is a Class A product. In a domestic environment this product may cause radio interference, in which case the user may be required to take corrective actions.
Palo Alto Networks Compliance Statements • 25
BSMI Statement
BSMI Statement
26 • Compliance Statements Palo Alto Networks
Appendix A
General Safety Information
CAUTION
Please Note the Following:
1.
The M-100 should not be used in a home, school or other public area where the general population would have access to it.
2.
The manufacturer specifies that the thumbscrew should be tightened with a screwdriver.
Use of a thumbscrew is not to compromise the basic principles of safety.
WARNING
To prevent the potential for personal injury, property damage, or death, please observe the following instructions:
• Do not use damaged equipment, including exposed, frayed or damaged power cords. Use only the approved power cable that is rated for the equipment. The voltage and current rating of the cable should be greater than the ratings marked on the equipment.
• Plug the power cables into properly grounded electrical outlets. Do not use adapter plugs or
remove the grounding prong from a cable.
• Observe extension cable and power strip ratings to ensure that the total ampere rating of all equipment plugged into the extension cable or power strip does not exceed 80 percent of the ampere ratings limit for the extension cable or power strip.
• The power supplies in the M-100 may produce high voltages and potential energy hazards. By opening the cover of the M-100 you may be exposed to a risk of electric shock.
The components inside the M-100 housing should only be serviced by Palo Alto
Networks.
• The M-100 should not be operated with the cover removed.
• Components inside the M-100 housing may become extremely hot during normal operation. These components include the memory and CPU modules. Allow sufficient time for components to cool before handling.
• The M-100 should not be operated in environments that can get wet. Protect the M-100 at all times from liquid intrusion.
• If your M-100 gets wet, turn off the AC power at the circuit breaker before attempting to remove the power cables from the electrical outlet. Then disconnect power to the equipment and to any attached devices.
Palo Alto Networks • 27
28 •
• Avoid obstructing the air vents on the M-100 or pushing objects into the openings. This could lead to fire or electric shock.
CAUTION
To prevent hardware damage or loss of data, observe the following precautions:
• Follow installation instructions carefully.
• Do not attempt to service the equipment yourself.
• You should operate this equipment from the type of external power source indicated on the electrical ratings label.
• Wait 30 seconds after turning off the equipment before removing a component from the system or disconnecting a peripheral device from the M-100.
• Always leave at least 4 inches (10.2cm) of physical clearance on all vented sides of the M-
100. This permits the airflow required for proper ventilation.
• Avoid placing equipment too close together such that it is subject to re-circulated (preheated) air. Avoid placing equipment too close to an appliance or exhaust vent.
• Ensure that cables are connected to the M-100 without stress and that nothing rests on the cables.
• If the equipment is located in a rack, move it with caution. Ensure that all casters and/or stabilizers are firmly connected. While moving the equipment, avoid uneven surfaces and sudden stops.
• Do not place other equipment, monitors, or other devices on top of the M-100.
• To protect the M-100 from fluctuations in electrical power, use a surge suppressor, line conditioner or uninterruptible power supply (UPS).
CAUTION
Please observe the following additional precautions for rack-mounted systems:
• Slide rail mounted equipment is not to be used as a shelf or a work space.
• Elevated Operating Ambient – If the M-100 is installed in a closed or multi-unit rack assembly, the operating ambient temperature in the rack environment may be greater than the room ambient temperature. Therefore, consideration should be given to the
maximum operating temperature specified in “Environmental Specifications” on page 24.
• Reduced Air Flow – Installation of the M-100 in a rack should be such that the amount of air flow required for safe operation is not compromised.
• Mechanical Loading – Mounting of the M-100 in the rack should not create a hazardous condition from uneven mechanical loading.
• Circuit Overloading – Connection of the equipment to the supply circuit should not create an overloaded situation. Pay close attention to equipment nameplate ratings.
Palo Alto Networks
Other Regulatory Information
• Reliable Grounding – Devices mounted in racks should be grounded properly. If using power strips to connect the M-100 to the supply circuit, make certain that the power strips are also grounded properly.
• It is your responsibility to ensure that the rack and the provided rail system are compatible with each other before installing the M-100.
• Install the front and side stabilizers on the rack prior to installing equipment. Failure to install stabilizers may cause a rack to tip over.
• Load racks from the bottom up, loading the heaviest items near the bottom of the rack.
• Do not stand or step on components in the rack.
WARNING
Grounding Instructions for Qualified Electricians Only:
• Grounding techniques may vary. However, a positive connection to a safety (earth) ground is required.
• Make the ground connection first and disconnect it last to prevent hazards.
• Never defeat the ground conductor or operate the equipment in the absence of a suitably installed ground conductor.
• If the system is installed in a rack, ensure that the system chassis is securely grounded to the rack cabinet frame. Do not connect power to the system until grounding cables are connected.
Other Regulatory Information
Export Regulations
Customer acknowledges that these Products, which may include technology and software, are subject to the customs and export control laws and regulations of the United
States (“U.S.”) and may also be subject to the customs and export laws and regulations of the country in which the Products are manufactured and/or received. Customer agrees to abide by those laws and regulations. Further, under U.S. law, the Products may not be sold, leased or otherwise transferred to restricted end-users or to restricted countries. In addition, the Products may not be sold leased or otherwise transferred to, or utilized by an end-user engaged in activities related to weapons of mass destruction, including without limitation, activities related to the design, development, production or use of nuclear weapons, materials or facilities, missiles or the support of missile projects, and chemical or biological weapons.
Palo Alto Networks • 29
30 • Palo Alto Networks
Download
Public link updated
The public link to your chat has been updated. You may view and manage your chat links after registration here.
Document public link
Advertisement
Key features
Central management
Log collection
Log collector
Redundant disk drives
High performance
Scalable
Easy to install
Easy to configure
Management interface
Frequently asked questions
The M-100 is a multi-function appliance that can be configured as either a dedicated log collector or a central management system for Palo Alto Networks firewalls. It can perform both central management and log collection for Palo Alto Networks firewalls, or function as a dedicated Log Collector.
The M-100 appliance can be configured for either Panorama mode for central management and log collection or Log Collector mode for functioning as a dedicated Log Collector.
The minimum Panorama version that you can install on an M-100 appliance is 7.0.
