Always there to help you

Register your product and get support at www.philips.com/welcome

Contact

Philips

AEA7000

User manual

Contents

Contents

1 Important

2

Safety 2

Notice 3

2 Your Wireless Microphone and

Bluetooth

®

Speaker

6

Introduction 6

What's in the box

Overview of the unit

6

6

3 Get started

8

Connect power

Switch on the Bluetooth ® speaker

Install/replace microphone batteries

8

8

8

4 Play

10

Sing along through the wireless microphone 10

Play from a Bluetooth ® enabled device 11

Play and charge your iPad through the dock connector directly

Play from an external device

12

13

5 Product information

14

Specifications 14

6 Troubleshooting

15

EN 1

1 Important

Safety

This 'bolt of lightning' indicates uninsulated material within the device may cause an electrical shock. For the safety of everyone in your household, please do not remove the covering.

The 'exclamation mark' calls attention to features for which you should read the enclosed literature closely to prevent operating and maintenance problems.

WARNING: To reduce the risk of fire or electric shock, the device should not be exposed to rain or moisture and objects filled with liquids, such as vases, should not be placed on the device.

CAUTION: To prevent electric shock, fully insert the plug. (For regions with polarized plugs: To prevent electric shock, match wide blade to wide slot.)

Important Safety Instructions

a Read these instructions.

b Keep these instructions.

c Heed all warnings.

d Follow all instructions.

e Do not use this apparatus near water.

f Clean only with dry cloth.

g Do not block any ventilation openings.

Install in accordance with the manufacturer's instructions.

2 EN h Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. i Do not defeat the safety purpose of the polarized or grounding-type plug.

A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety.

If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

j Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

k Only use attachments/accessories specified by the manufacturer.

l Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer or sold with the apparatus.

When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. m Unplug this apparatus during lightning storms or when unused for long periods of time.

n Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

o Battery usage CAUTION – To prevent battery leakage which may result in bodily injury, property damage, or damage to the unit:

• Install all batteries correctly, + and - as marked on the unit.

• Remove batteries when the unit is not used for a long time.

• Perchlorate Material-special handling may apply. See www.dtsc.ca.gov/ hazardouswaste/perchlorate.

p Apparatus shall not be exposed to dripping or splashing, keep it away from direct sunlight,naked flames or heat.

Warning

• Never remove the casing of this apparatus.

• Never lubricate any part of this apparatus.

• Never place this apparatus on other electrical equipment.

• Keep this apparatus away from direct sunlight, naked flames or heat.

• Ensure that you always have easy access to the power cord, plug or adaptor to disconnect this apparatus from the power.

Risk of overheating! Never install this apparatus in a confined space. Always leave a space of at least four inches around this apparatus for ventilation. Ensure curtains or other objects never cover the ventilation slots on this apparatus.

Information about the use of batteries:

Caution

• Risk of leakage: Only use the specified type of batteries.

Do not mix new and used batteries. Do not mix different brands of batteries. Observe correct polarity.

Remove batteries from products that are not in use for a longer period of time. Store batteries in a dry place.

• Risk of injury: Wear gloves when handling leaking batteries. Keep batteries out of reach of children and pets.

• Risk of explosion: Do not short circuit batteries. Do not expose batteries to excessive heat. Do not throw batteries into the fire. Do not damage or disassemble batteries. Do not recharge non-rechargeable batteries.

Notice

Notice of compliance

Modifications

The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

FCC & RSS compliance statement

This device complies with Part 15 of the FCC

Rules and Industry Canada licence-exempt

RSS standard(s). Operation is subject to the following two conditions: a This device may not cause harmful interference, and b This device must accept any interference received, including interference that may cause undesired operation.

FCC Radiation Exposure Statement

This equipment complies with FCC’s and IC’s

RF radiation exposure limits set forth for an uncontrolled environment. The antenna(s) used for this transmitter must be installed and

EN 3

operated to provide a separation distance of at least 20 cm from all persons and must not be collocated or operating in conjunction with any other antenna or transmitter. Installers must ensure that 20cm separation distance will be maintained between the device (excluding its handset) and users.

FCC rules

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Canada:

This digital apparatus does not exceed the Class

B limits for radio noise emissions from digital apparatus as set out in the Radio Interference

Regulations of the Canadian Department of

Communications. This Class B digital apparatus complies with Canadian ICES-003 and RSS-210 of Industry Canada.

Disposal of your old product and batteries

Your product is designed and manufactured with high quality materials and components, which can be recycled and reused.

Never dispose of your product with other household waste. Please inform yourself about the local rules on the separate collection of electrical and electronic products and batteries.

The correct disposal of these products helps prevent potentially negative consequences on the environment and human health.

Your product contains batteries, which cannot be disposed of with normal household waste.

Please inform yourself about the local rules on separate collection of batteries. The correct disposal of batteries helps prevent potentially negative consequences on the environment and human health.

Please visit www.recycle.philips.com for additional information on a recycling center in your area.

Environmental information

All unnecessary packaging has been omitted.

We have tried to make the packaging easy to separate into three materials: cardboard (box), polystyrene foam (buffer) and polyethylene

(bags, protective foam sheet.)

Your system consists of materials which can be recycled and reused if disassembled by a specialized company. Please observe the local regulations regarding the disposal of packaging materials, exhausted batteries and old equipment.

“Made for iPad” means that an electronic accessory has been designed to connect specifically to iPad, and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the

4 EN

operation of this device or its compliance with safety and regulatory standards. Please note that the use of this accessory with iPad may affect wireless performance.

iPad is a trademark of Apple Inc., registered in the U.S. and other countries.

The Bluetooth ® word mark and logos are registered trademarks owned by Bluetooth

SIG, Inc. and any use of such marks by Philips is under license.

Note

• The type plate is located on the back of the unit.

EN 5

6 EN

2 Your Wireless

Microphone and Bluetooth

®

Speaker

Congratulations on your purchase, and welcome to Philips! To fully benefit from the support that Philips offers, register your product at www.philips.com/welcome.

If you contact Philips, you will be asked for the model and serial number of this apparatus. The model number and serial number are on the back of the apparatus. Write the numbers here:

Model No. __________________________

Serial No. ___________________________

Introduction

With the Philips wireless microphone and

Bluetooth ® speaker, you can:

• dock your iPad onto the speaker to sing along with music from the app

(The Voice: On Stage) through the wireless microphone.

With the Bluetooth ® speaker, you can:

• play music from a Bluetooth

Audio Distribution Profile).

® enabled device that supports A2DP (Advanced

• charge or play music from your iPad directly through the dock connector.

• play music from other audio devices through the AUDIO-IN socket.

What's in the box

Check and identify the contents of your package:

• Wireless microphone

• Bluetooth ® speaker

• AC power cord

• 3 X AAA batteries

• Quick start guide a b a Line out socket

• Safety sheet

Overview of the unit

Wireless microphone

• (To use the microphone separately) connect to the MIC input socket of an existing Hi-Fi system.

b Battery compartment c d c OFF/ON

• Switch the microphone on or off.

d Power indicator

• Light up red when the wireless microphone is switched on.

• Flash red when the battery level is low.

Bluetooth ® speaker a a Power indicator b

• Indicate the power status.

• Turn the unit on/off.

c b i d ef c Bluetooth ® indicator

• Indicate the Bluetooth ® status.

d -/+

• Adjust volume.

h g e

• (Press) pair with a Bluetooth

Audio Distribution Profile).

® enabled device that supports A2DP (Advanced

• (Press and hold) pair with the wireless microphone in case automatic pairing fails.

f Dock for iPad g SOFTWARE UPGRADE (not for use by end users) h AUDIO-IN

• Connect an external audio player through a 3.5mm audio input cable

(not supplied).

i AC MAINS~

• AC power socket.

EN 7

3 Get started

Always follow the instructions in this chapter in sequence.

Connect power

Caution

• Risk of product damage! Make sure that the power supply voltage corresponds to the voltage printed on the back of the unit.

• Risk of electric shock! When you unplug the AC power cord, always pull the plug from the socket. Never pull the cord.

• Before you connect the AC power cord, make sure that you have completed all the other connections.

• Connect the AC power cord to

• the AC MAINS~ socket on the back of the Bluetooth ® speaker.

• the wall power socket.

Switch on the Bluetooth

®

speaker

• Press on the top of the Bluetooth ® speaker.

» The power indicator lights up white.

» The Bluetooth indicator flashes blue slowly.

8 EN

• To switch the unit to standby mode, press

on the top panel.

• To switch the unit on from standby mode, press again.

Tip

• If the speaker stays idle for more than 15 minutes, it switches to standby mode automatically.

Install/replace microphone batteries

Caution

• Risk of explosion! Keep batteries away from heat, sunshine, or fire. Never discard batteries in fire.

• Danger of explosion if batteries are incorrectly replaced. Replace only with the same or equivalent type.

• Batteries contain chemical substances, so they should be disposed of properly.

1

Open the battery compartment and take out the battery cartridge.

2

Insert 3 x AAA batteries (supplied) into the cartridge with correct polarity (+/-) as indicated.

Note

3

Push back the battery cartridge, then close the battery compartment.

• If you are not going to use the microphone for a long time, remove the batteries.

• New batteries installed in the microphone support up to 25 hours of continuous use.

• When the power indicator flashes red, it indicates that the power level is low and you need to replace the batteries.

EN 9

10 EN

4 Play

Sing along through the wireless microphone

Note

• The effective operation range between the wireless microphone and Bluetooth

10 meters (30 feet).

® speaker is approximately

1

Dock your iPad onto the Bluetooth ® speaker.

» A prompt pops up on the iPad screen, asking you to install the relevant app.

If no prompt pops up on your iPad, you can go to Settings -> General ->

About -> AEA7000 -> Find App for

Accessory to install the app.

2

Tap YES on the prompt to install the app

(The Voice: On Stage) from Apple App

Store.

3

After successful installation, run The Voice:

On Stage on the iPad.

4

Slide the OFF/ON switch on the wireless microphone to the ON position, then select a song from the app and tap SING

-> RECORD.

» The wireless microphone starts to pair with the Bluetooth ® speaker automatically.

» After successful pairing and connection, the Bluetooth ® blue.

indicator turns solid

5

Find and download a tutorial from The

Voice: On Stage, then tap SING for how to sing along through the wireless microphone and Bluetooth ® speaker.

6

Select a song from The Voice: On Stage and sing along through the wireless microphone.

7

Use -/+ on the top of the Bluetooth ® speaker to adjust volume.

Tip

• Always update the app to the latest version.

• If automatic pairing fails, press and hold on the speaker for more than 10 seconds to pair the microphone with the speaker manually.

• If the wireless microphone remains disconnected from the Bluetooth ® speaker for more than 15 minutes, it switches to standby mode automatically. To switch it on again, you need to slide the OFF/ON switch on the microphone to theOFF position and then slide back to the ON position.

• You can use controls available on the app to adjust sound effects.

• If you experience howling or echo, try to increase the distance between the microphone and speaker or adjust the angle of the microphone towards the speaker.

Play from a Bluetooth

®

enabled device

Note

• The effective operation range between the Bluetooth ® speaker and your Bluetooth ® enabled device is approximately 10 meters (30 feet).

• To pair with a Bluetooth ® enabled mobile device, make sure that: no iPad is docked; or you have stopped music play and exited The Voice: On Stage on your docked iPad.

• To pair with a new mobile device, you can press to remove the existing Bluetooth ® connection.

• To play from a Bluetooth ® enabled device, make sure that you are not playing music from your iPad docked on the Bluetooth ® speaker.

1

Press on the top of the Bluetooth ® speaker.

» The Bluetooth quickly.

® indicator flashes blue

2

Enable Bluetooth ® on your device that supports A2DP (Advanced Audio

Distribution Profile).

EN 11

12 EN

3

Select 'PHILIPS_AEA7000' on your

Bluetooth ® enabled device and if necessary input '0000' as the paring password.

» After successful pairing and connection, the Bluetooth ® indicator on the speaker turns solid blue and the speaker beeps twice.

4

Start music play on your Bluetooth ® enabled device.

5

Use -/+ on the top of the Bluetooth ® speaker to adjust volume.

Play and charge your iPad through the dock connector directly

Compatible iPad

This unit supports play and charge of the following iPad models:

• New iPad

• iPad 2

To remove the iPad

• iPad

Load the iPad

• Dock your iPad.

• Pull the iPad out of the dock.

Listen to the iPad

1

Make sure that the iPad has been loaded correctly.

2

Start music play on your iPad.

» The connected iPad starts to play.

3

Use -/+ on the top of the Bluetooth ® speaker to adjust volume.

Charge the iPad

The docked iPad begins to charge as soon as the unit is connected to AC power.

You can also listen to an external audio player through the Bluetooth ® speaker.

AUDIO-IN

Play from an external device

1

Connect a 3.5mm audio cable (not supplied) to:

• the AUDIO-IN socket on the back of the Bluetooth ® speaker.

• the headphone socket on an external audio player.

2

Start music play on the external audio player.

3

Use -/+ on the top of the Bluetooth ® speaker to adjust volume.

EN 13

5 Product information

Note

• Product information is subject to change without prior notice.

Dimensions (W x H x D)

• Speaker

• Microphone

Weight

• Speaker

• Microphone

300 x 124 x 156mm

162 x 317 x 162mm

1.3 kg

0.3kg

Specifications

Amplifier

Rated Output Power

Signal to Noise Ratio

Aux-in Link

2 X 5W RMS

>70dB

600 mV RMS, 20 kohm

Speakers

Speaker Impedance

Speaker Driver

Sensitivity

4 ohm

70mm full range

> 84dB/1m/1W

Bluetooth

®

Bluetooth ® version V2.1 + EDR

Frequency band 2.402-2.480 GHzISM

Band

Range 10m (free space)

General information

AC power

Operation Power

Consumption

Standby Power

Consumption

100-240 V~; 50/60 Hz

20 W

<0.5W

14 EN

6 Troubleshooting

Warning

• Never remove the casing of this device.

To keep the warranty valid, never try to repair the system yourself.

If you encounter problems when using this device, check the following points before requesting service. If the problem remains unsolved, go to the Philips Web page (www.

philips.com/support). When you contact Philips, make sure that the device is nearby and the model number and serial number are available.

No power to the Bluetooth ® speaker

• Make sure that the AC power plug of the device is connected properly.

• Make sure that there is power at the AC outlet.

• As a power-saving feature, the speaker switches to standby mode automatically after staying idle for more than 15 minutes.

Switch on the speaker again (see 'Switch

on the Bluetooth ®

speaker' on page 8).

No power to the wireless microphone

• The batteries may be installed incorrectly

or drained. Install or replace the batteries properly (see 'Install/replace microphone batteries' on page 8).

• As a power-saving feature, the microphone switches to standby mode automatically after staying disconnected from the speaker for more than 15 minutes. To switch it on again, you need to slide the

OFF/ON switch on the microphone to the

OFF position and then back to the ON position.

No sound or poor sound

• Adjust volume.

• Check the Bluetooth ® connection.

• Check whether you have started music play on the connected device.

Failed to set up connection between the microphone and speaker

• Check whether both the wireless microphone and Bluetooth are switched on.

® speaker

• Make sure that the wireless microphone and Bluetooth ® speaker are within the the effective operation range, that is, approximately 10 meters

(30 feet).

• Press and hold on the top of the

Bluetooth ® speaker for more than 10 seconds to set up wireless connection manually.

Howling or echo from the wireless microphone

• Adjust volume.

• Increase the distance between the microphone and speaker or adjust the angle of the microphone towards the speaker.

No response from the Bluetooth ® speaker

• Disconnect and reconnect the AC power plug, and then switch on the device again.

EN 15

Specifications are subject to change without notice

© 2012 Koninklijke Philips Electronics N.V.

All rights reserved.

AEA7000_07_UM_EN_V1.0