advertisement
EVID Compact Sound Speaker System
EVID-C44, EVID-C2.1, EVID-40C, EVID-S44, EVID-S44W, EVID-2.1, EVID-2.1W, EVID-40S, and
EVID-40SW
en | Installation Manual
1
2
3
4
5
6
7
8
Table of contents
Safety
Introduction
System overview
Installation
Ceiling mount satellite speaker installation
Ceiling mount subwoofer installation
Surface mount satellite speaker installation
Surface mount subwoofer installation
Removing subwoofer from the wall
Wiring
8 ohm Stereo Surface Mount Subwoofer Only
Troubleshooting
Technical data
Notes
en
3
15
7
4
6
31
32
34
26
Electro-Voice Installation Manual 2015.12 | 07 | F.01U.310.295
EVID Compact Sound Speaker System
1
!
Safety
Warning!
Suspending any object is potentially dangerous and should only be attempted by individuals who have a thorough knowledge of the techniques and regulations of suspending objects overhead. Electro-Voice strongly recommends all loudspeakers be suspended taking into account all current national, federal, state, and local laws and regulations. It is the responsibility of the installer to ensure all loudspeakers are safely installed in accordance with all such requirements. When loudspeakers are suspended, Electro-Voice strongly recommends the system be inspected at least once per year or as laws and regulations require. If any sign of weakness or damage is detected, remedial action should be taken immediately. The user is responsible for making sure the wall, ceiling, or structure is capable of supporting all objects suspended overhead. Any hardware used to suspend a loudspeaker not associated with Electro-Voice is the responsibility of others.
Surface mount speakers
Safety Agency Compliance
The EVID 2.1 and EVID 40S bracket systems have successfully passed EIA-636 at a safety factor of 8:1. The bracket systems are intended to support only the EVID 2.1 and EVID 40S respectively. Do not use either bracket system for any other purpose. Never set anything on or hang anything from the EVID 2.1 or EVID 40S enclosures when using the brackets.
Redundant safety point
As an added safety measure, it is suggested the user install an extra suspension point back to the building structural supports. This redundant safety point should have as little slack as possible (less than 1-inch is preferable).
!
Figure 1.1: Surface mount satellite speaker (left) and surface mount subwoofer (right) with safety cable
Ceiling mount speakers
Caution!
The seismic tab (auxiliary support ring) is not intended for primary suspension of the loudspeaker. The seismic tab should only be used as a secondary safety point.
2015.12 | 07 | F.01U.310.295
Installation Manual Electro-Voice
!
en
5
Caution!
Ceiling mount speaker’s safety cable
The safety cable should be installed with a minimum of 3-inches (76.2 mm) of slack.
Old electrical and electronic appliances
Electrical or electronic devices that are no longer serviceable must be collected separately and sent for environmentally compatible recycling (in accordance with the European Waste
Electrical and Electronic Equipment Directive).
To dispose of old electrical or electronic devices, you should use the return and collection systems put in place in the country concerned.
Electro-Voice Installation Manual 2015.12 | 07 | F.01U.310.295
EVID Compact Sound Speaker System
2
2.1
Introduction
The EVID Compact Sound Speaker System is a very compact full-range loudspeaker ideal for applications requiring high-quality sound. Its shape flexibility and size make it nearly invisible for use in background/foreground music systems for restaurants, bars, patios, retail, and other applications. The system consists of a high performance 8-inch subwoofer module with a crossover network to support the included four (4) 2-inch satellite speakers. The system provides for easy signal connections at the subwoofer and can support either 4/8 ohm or
70/100v signal connections. Its high power handling allows the system to be used in a wide variety of environments and spaces to provide high quality background or foreground music.
Read through this manual to familiarize yourself with the safety information, features, and applications before you use these products.
System features
Common system features:
▪
Available as a complete pre-packaged systems in either Ceiling mount or Surface mount configurations.
▪
Components can be combined in any mix of 4 satellite speakers to a single subwoofer to meet décor or installation requirements.
▪
Supports up to 100 W, 70/100 V, and 8 ohm audio connections.
Ceiling version features:
▪ Quick-install design with captive mounting tabs to fit nearly any ceiling construction.
▪
Four-pin Phoenix connectors on ceiling satellite speakers support pass-thru wiring.
▪
UL 2043/1480 ratings allow for use in signaling applications and plenum air spaces.
▪
Ceiling cutout templates and all mounting accessories included.
▪
Available in white finish.
Surface-mount version features:
▪
Simplified mounting design for satellites—concept provides secure mounting while allowing for significant articulation and range of motion.
▪
Attractive subwoofer design with full-face grille—install it anywhere, no need to hide!
▪
Supports stereo operation with 8-ohm audio connections.
▪ Quick-mount slide-on wall bracket included.
▪
Available in black or white finishes.
2015.12 | 07 | F.01U.310.295
Installation Manual Electro-Voice
en
7
3
3.1
System overview
Packing lists
Ceiling mount speakers
The EVID C44 speaker system package contains four (4) satellite speakers and one (1) subwoofer. When you open the box for the full system you will find three (3) main boxes inside; two (2) boxes for the satellite speakers and one (1) box for the subwoofer.
The major components included in one (1) box for the EVID C2.1 ceiling mount satellite speaker.
Item
A
B
C
D
Quantity
2
2
2
1
Description
EVID C2.1 ceiling mount satellite speakers
Grilles
C-ring supports
Cutout template
E
F
1
2
Engineering data sheet
Paint shields
Table 3.1: Ceiling Mount Satellite Speaker
Figure 3.1: Components in kit
Electro-Voice Installation Manual 2015.12 | 07 | F.01U.310.295
EVID Compact Sound Speaker System
The major components included in the box for the EVID 40C ceiling mount subwoofer:
Item
A
B
C
D
Quantity Description
1
2
1
1
EVID 40C ceiling mount subwoofer
Tile rails
C-ring support
Grille
E
F
1
2
Installation manual screws
G 1 Cutout template
H 1 Paint shield
Table 3.2: Ceiling Mount Subwoofer
Figure 3.2: Components in kit
2015.12 | 07 | F.01U.310.295
Installation Manual Electro-Voice
en
9
Surface mount speakers
The EVID S44 speaker system package contains four (4) satellite speakers and one (1) subwoofer. When you open the box for the full system you will find three (3) main boxes inside; two (2) boxes for the satellite speakers and one (1) box for the subwoofer.
The major components included in one (1) box for the EVID 2.1 surface mount satellite speaker.
C
D
E
Item
A
B
Quantity Description
2 EVID 2.1 surface mount satellite speakers
2
2
1
2
Wall brackets
Speaker brackets
Engineering Data Sheet
M6 hex drive pan-head screws
F
G
4
2
M5 pan-head screws
Screw sockets
H 1 Hex wrench
Table 3.3: Surface Mount Satellite Speaker (1 box)
Figure 3.3: Components in kit
Electro-Voice Installation Manual 2015.12 | 07 | F.01U.310.295
EVID Compact Sound Speaker System
The major components included in the box for the EVID 40S surface mount subwoofer:
Item
A
B
C
D
Quantity
1
1
1
4
Description
EVID 40S surface mount subwoofer
Wall bracket, assembled in box
Installation Manual
M6 hex drive pan-head screw
E
F
4
1
Rubber feet
Hex wrench
Table 3.4: Surface Mount Subwoofer
Figure 3.4: Components in kit
2015.12 | 07 | F.01U.310.295
Installation Manual Electro-Voice
3.2
Product information
Ceiling mount speakers
en
11
Figure 3.5: EVID C2.1 Product Information
Figure 3.6: EVID 40C Product Information
Electro-Voice Installation Manual 2015.12 | 07 | F.01U.310.295
EVID Compact Sound Speaker System
Surface mount speakers
Figure 3.7: EVID 2.1 Product Information
Figure 3.8: EVID 40S Product Information
2015.12 | 07 | F.01U.310.295
Installation Manual Electro-Voice
3.3
Dimensions
Ceiling mount speakers
en
13
Figure 3.9: Dimensions EVID C2.1
Electro-Voice
Figure 3.10: Dimensions EVID 40C
Installation Manual 2015.12 | 07 | F.01U.310.295
EVID Compact Sound Speaker System
Surface mount speakers
Figure 3.11: Dimensions EVID 2.1 and mounting bracket
Figure 3.12: Dimensions EVID 40S and mounting bracket
Notice!
The mounting bracket dimension drawings are not to scale. Drawing sizes increased for readability.
2015.12 | 07 | F.01U.310.295
Installation Manual Electro-Voice
4
4.1
4.1.1
en
15
Installation
Ceiling mount speakers
Ceiling mount satellite speaker installation
For safety, ensure the ceiling tiles or building structure supports more than the weight of the speaker. Consult an expert if you are unsure.
Installing a ceiling mount satellite speaker
To install a ceiling mount satellite speaker, do the following:
1.
Trace the cutout template.
2.
Cut the hole.
3.
Attach the C-Ring.
Electro-Voice Installation Manual 2015.12 | 07 | F.01U.310.295
EVID Compact Sound Speaker System
4.
Install the wire conduit into the speaker.
5.
Install wires into the Phoenix connector.
6.
Tighten the two (2) screws to secure the conduit clamp.
7.
Attach the safety cable.
The safety cable should be installed with a minimum of a 3-inch (76.2 mm) slack.
2015.12 | 07 | F.01U.310.295
Installation Manual Electro-Voice
8.
Push the speaker up into the ceiling.
en
17
9.
Tighten the mounting tabs.
10. Attach the grille.
11. Installation complete.
Electro-Voice
For more information, see Safety.
Installation Manual 2015.12 | 07 | F.01U.310.295
EVID Compact Sound Speaker System
4.1.2
Ceiling mount subwoofer installation
For safety, ensure the ceiling tiles or building structure supports more than the weight of the speaker. Consult an expert if you are unsure.
Installing a ceiling mount subwoofer
To install a ceiling mount subwoofer, do the following:
1.
Trace the cutout template.
2.
Cut the hole.
3.
Secure rails to the C-Ring.
2015.12 | 07 | F.01U.310.295
Installation Manual Electro-Voice
4.
Attach the safety cable to the auxiliary support tab.
en
19
5.
Route wires through the ceiling to the conduit clamp.
6.
Connect the wires to the Phoenix connectors.
Electro-Voice Installation Manual 2015.12 | 07 | F.01U.310.295
EVID Compact Sound Speaker System
7.
Plug the phoenix connector into the socket.
8.
Tighten the two (2) screws to secure the conduit clamp.
9.
Push the speaker up into the ceiling.
2015.12 | 07 | F.01U.310.295
Installation Manual Electro-Voice
10. Tighten mounting tabs.
11. Attach the grille.
12. Attach the auxiliary support line to the structure.
The safety cable should be installed with a minimum of a 3-inch (76.2 mm) slack.
en
21
13. Installation complete.
Electro-Voice
For more information, see Safety.
Installation Manual 2015.12 | 07 | F.01U.310.295
EVID Compact Sound Speaker System
4.2
4.2.1
Surface mount speakers
Surface mount satellite speaker installation
For safety, ensure the mounting surface supports more than the weight of the speaker. Use only industry-accepted fasteners and mounting methods when mounting the wall bracket.
Consult an expert if you are unsure.
Installing a surface mount satellite speaker
To install a surface mount satellite speaker, do the following:
1.
Using a Phillips head screwdriver (not supplied), tighten two (2) M5 pan-head screws
(not supplied) to attach the wall bracket to a secure mounting surface.
2.
Using a Philips screwdriver, tighten two (2) M5 pan-head screws (supplied) to attach the speaker bracket to the rear of the cabinet.
3.
Place the speaker bracket onto the wall bracket.
4.
Using the hex wrench (supplied), tighten the M6 hex drive pan-head screw to secure the speaker bracket to the wall bracket.
For more information, see Safety, page 4.
2015.12 | 07 | F.01U.310.295
Installation Manual Electro-Voice
4.2.2
Wall bracket range of motion
The speaker can be adjusted from side to side or up and down.
en
23
4.2.3
!
Figure 4.1: Horizontal range is 160° and the vertical range is 60°.
Surface mount subwoofer installation
For safety, ensure the mounting surface supports more than the weight of the speaker. Use only industry-accepted fasteners and mounting methods when mounting the wall bracket.
Consult an expert if you are unsure.
Caution!
Only mount the wall bracket in the vertical V-shape position.
Do not mount the V-bracket or wall bracket side ways or upside down.
Electro-Voice
Figure 4.2: Wall bracket correct and incorrect mounting positions
Installation Manual 2015.12 | 07 | F.01U.310.295
EVID Compact Sound Speaker System
!
Caution!
Do not mount the surface mount subwoofer on the ceiling.
The surface mount subwoofer is not designed to mount on the ceiling.
Installing a surface mount subwoofer
To install a surface mount subwoofer, do the following:
1.
Using a Phillips head screwdriver (not supplied), tighten six (6) M5 pan-head screws
(not supplied) to attach the wall bracket to a secure mounting surface.
2.
Using the hex wrench (supplied), tighten the three (3) M6 hex drive pan head screws to attach the V-bracket.
2015.12 | 07 | F.01U.310.295
Installation Manual Electro-Voice
3.
Slide the V-bracket into the wall bracket.
The locking detents engage.
en
25
4.2.4
For more information see, Safety, page 4.
Removing subwoofer from the wall
To remove the subwoofer from the wall, do the following:
1.
Pull the subwoofer slightly out from the wall.
2.
Lift the subwoofer up.
The locking detents disengage.
Electro-Voice Installation Manual 2015.12 | 07 | F.01U.310.295
EVID Compact Sound Speaker System
5
5.1
5.1.1
Wiring
Ceiling mount speakers
Wattage tap
Prior to wiring your system, select the mode of operation (100V/70V/4 ohm) by selecting power taps using the rotary switch on the subwoofer input panel. The power taps are 100 W,
50 W, 25 W, and 12.5 W at 70V or 100 W, 50 W, and 25 W 100V. The power selector switch is located on the baffle behind the grille.
Figure 5.1: EVID 40C Wattage Tap
2015.12 | 07 | F.01U.310.295
Installation Manual Electro-Voice
5.1.2
en
27
70v/100v/4 ohm Mono
The amplifier and EVID Compact Sound Speaker System product family is wired for MONO mode. It is highly advisable to support the unit while these connections are being made.
Connect all wires to the speaker at the back terminal plate observing proper polarity of the connections. After all connections are made, test the complete system operation.
OR
OR
EVID 2.1
OR
+
LEFT
IN -
+
SAT1
OUT -
+
SAT3
OUT -
GND
LOOP
THRU
+ -
+
SAT2
OUT -
+
SAT4
OUT -
OR
EVID 2.1
EVID P2.1
EVID C2.1
EVID C2.1
EVID P2.1
EVID 2.1
EVID P2.1
OR
OR
EVID 40C
EVID 2.1
OR
OR
EVID C2.1
EVID C2.1
EVID P2.1
Notice!
Any combination of four satellites (surface mount, ceiling or pendant speakers) is allowed.
The system is designed for operation with only four (4) satellite speakers. Operation with less than four (4) satellite speakers is not recommended.
Electro-Voice Installation Manual 2015.12 | 07 | F.01U.310.295
EVID Compact Sound Speaker System
5.2
5.2.1
Surface mount speakers
Wattage tap
Prior to wiring your system, select the mode of operation (100V/70V/4 ohm or 8 ohm stereo) by setting the slider switch to the appropriate setting. Select taps using the rotary switch on the subwoofer input panel. The power taps are 100 W, 50 W, 25 W, and 12.5 W at 70.7V and
100V, as well as a 4 ohm transformer bypass setting. A guide on the input panel shows which switch positions to use for the power settings at 70V and 100V.
Figure 5.2: EVID 40S wattage tap
2015.12 | 07 | F.01U.310.295
Installation Manual Electro-Voice
5.2.2
en
29
70v/100v/4 ohm Mono
The amplifier and EVID Compact Sound Speaker System is wired for MONO mode. It is highly advisable to support the unit while these connections are being made. Connect all wires to the speaker at the back terminal plate observing proper polarity of the connections. After all connections are made test the complete system operation.
Electro-Voice
Notice!
Any combination of four satellites (surface mount, ceiling or pendant speakers) is allowed.
The system is designed for operation with only four (4) satellite speakers. Operation with less than four (4) satellite speakers is not recommended.
Installation Manual 2015.12 | 07 | F.01U.310.295
EVID Compact Sound Speaker System
5.2.3
8 ohm Stereo Surface Mount Subwoofer Only
The amplifier and EVID Compact Sound Speaker System is wired for STEREO mode. It is highly advisable to support the unit while these connections are being made. Connect all wires to the speaker at the back terminal plate observing proper polarity of the connections after all connections are made test the complete system operation.
Notice!
Any combination of four satellites (surface mount, ceiling or pendant speakers) is allowed.
The system is designed for operation with only four (4) satellite speakers. Operation with less than four (4) satellite speakers is not recommended.
Notice!
A standard low impedance (4/8 ohm) amplifier source is required when operating the unit in
STEREO mode.
100/70v operation is not supported in STEREO mode.
2015.12 | 07 | F.01U.310.295
Installation Manual Electro-Voice
en
31
6
Problem
No Sound
Poor Low-
Frequency
Response
Troubleshooting
Possible Causes
Amplifier
Wiring
Action
Connect a known working test speaker to the amplifier outputs. If there is no sound, check all electronics are on, the signal routing is correct, the source is active; the volume is turned up, and so on.
Correct/Repair/Replace as necessary. If there is sound, the problem is in the wiring.
Verify you have connected the correct wire pairs to the amplifier. Play something at low level through the amplifier (for example, from a CD player or tuner). Connect the test speaker in parallel with the malfunctioning line. If the sound has gone or is very weak, the line has a short in it (possibly a severe scrape, pinch, or staple puncture). If the sound level is normal the wire is open (possibly a cut wire or missed connection). Using the test speaker, move down the line and test each connection/junction until you find the problem and correct it. Observe proper polarity.
Speakers Wired Outof-Polarity
When two (2) speakers are connected out of polarity (out of phase), the low frequencies will cancel each other acoustically. Carefully observe the wire markings or tracers on your speaker wires. Verify the amplifier (+) terminal is connected to the red speaker terminals and the amplifier (-) terminal is connected to the black speaker terminals.
Improperly Wired
Subwoofer Panel
Verify you have the inputs and outputs connected to the correct wires.
If the subwoofer input panel is not correctly wired, there will be little or no sound. Observe proper polarity.
Faulty Connection
Using a test speaker as described above, verify all amplifier and speaker wires are connected to their proper terminals with the correct polarity. Reversing just one (1) set of amplifier wires can cut out all bass output from the subwoofer.
Check all connections at amplifier and speakers to ensure they are clean and tight. If the problem persists, it may be in the amplifier or wiring. See other actions above.
Intermittent
Output such as,
Crackling or
Distortion
Constant Noise such as Buzzing,
Hissing, Humming
Defective Amplifier or other Electronic
Device
If the noise is present but no program material is playing, the likely cause is the signal chain in the electronics. Evaluate each component as necessary to isolate the problem.
Poor System
Grounding or
Ground Loop
Check and correct the system grounding, as required.
If these suggestions do not solve your problem, contact your nearest Electro-Voice dealer or
Electro-Voice distributor.
Electro-Voice Installation Manual 2015.12 | 07 | F.01U.310.295
EVID Compact Sound Speaker System
7 Technical data
7.1
Ceiling mount speakers
EVID C2.1 and EVID 40C
7.1.1
EVID C2.1
Freq. Response (-10 dB): 180 Hz - 20 kHz
1
Power Handling: 30 W
2
Sensitivity: 84 dB
1
Impedance: 16 ohms
Maximum SPL: 102 dB
EVID 40C
45 Hz - 300 Hz
1
200 W
2
88 dB
1 mono 4 ohm
114 dB
Voice Coverage (H x V): 150° x 150°
3
Music Program Coverage (H x V): 100° x 100°
4
Transducer: 50 mm (1.97 in)
Omnidirectional
Omnidirectional
200 mm (7.87 in)
Connectors: Phoenix (4-pin)
Enclosure: Steel & ABS (fire rated)
Phoenix (2-pin)
Steel & ABS (fire rated)
Transformer Taps: N/A 100 W, 50 W, 25 W, 12.5W
Dimensions (H x Dia): 119 mm x 135 mm (4.7 in x 5.3 in) 316 mm x 373 mm (12.44 in x
14.69 in)
Cutout Size: 114 mm (4.49 in)
Net Weight:
(each)
0.82 kg (1.8 lb)
Shipping Weight:
(pair)
346 mm (13.6 in)
9.52 kg (21 lb)
1 sub and 4 satellites: 19.05 kg (42 lb)
Included Accessories: C-Ring C-Ring, Tile Rails
1
Half space.
2
Long Term Program Rating, 3 dB greater than continuous noise pink noise rating.
3 Average 1 kHz – 4 kHz.
4
Average 1 kHz – 8 kHz.
Frequency response
100
90
80
70
60
50 100 1000
Frequency (Hz)
EVID C2.1 Half Space
EVID 40C Half Space
10000 20000
2015.12 | 07 | F.01U.310.295
Installation Manual Electro-Voice
en
33
7.2
Surface Mount Speakers
EVID 2.1 and EVID 40S
7.2.1
EVID 2.1
Freq. Response (-10 dB): 180 Hz - 20 kHz 1
Power Handling: 30 W
2
EVID 40S
42 Hz - 300 Hz 1
200 W
2
Sensitivity: 84 dB
1
Impedance: 16 ohms
Maximum SPL: 102 dB
1
Voice Coverage (H x V): 150° x 150°
Music Program Coverage (H x V): 100° x 100°
3
4
Transducer: 50 mm (1.97 in)
Bracket Adjustment Range (H x V): 160° x 60°
Connectors: Phoenix (2-pin)
Enclosure: ABS (fire rated)
88 dB
1
Dual 8 ohm / mono 4 ohm
114 db
1
Omnidirectional
Omnidirectional
200 mm (7.87 in)
Fixed
Phoenix (2-pin)
Wood (MDF)
Transformer Taps: NA
Dimensions (H x W x D): 115 mm x 85 mm x 95 mm
(4.53 in x 3.35 in x 3.75 in)
100 W, 50 W, 25 W, 12.5 W
400 mm x 400 mm x 230 mm
(15.75 in x 15.75 in x 9.06 in)
Net Weight: (each) 0.5 kg (1.1 lb)
Shipping Weight:
12.05 kg (26.55 lb)
1 sub and 4 satellites: 18.26 kg (40.25 lb)
Included Accessories: Wall bracket; hex wrench Wall bracket; hex wrench
1
Half space (wall mounting).
2 Long Term Program Rating, 3 dB greater than continuous noise pink noise rating.
3
Average 1 kHz – 4 kHz.
4
Average 1 kHz – 8 kHz.
Frequency response
Electro-Voice Installation Manual 2015.12 | 07 | F.01U.310.295
EVID Compact Sound Speaker System
8 Notes
2015.12 | 07 | F.01U.310.295
Installation Manual Electro-Voice
en
35
Electro-Voice Installation Manual 2015.12 | 07 | F.01U.310.295
Bosch Sicherheitssysteme GmbH
Robert-Bosch-Ring 5
85630 Grasbrunn
Germany
www.boschsecurity.com
© Bosch Sicherheitssysteme GmbH, 2015
Bosch Security Systems, Inc
12000 Portland Avenue South
Burnsville MN 55337
USA
www.electrovoice.com
© Bosch Security Systems, Inc, 2015
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 1 Title Page
- 3 Table of Contents
- 4 Safety
- 6 Introduction
- 6 System features
- 7 System overview
- 7 Packing lists
- 11 Product information
- 13 Dimensions
- 15 Installation
- 15 Ceiling mount speakers
- 15 Ceiling mount satellite speaker installation
- 18 Ceiling mount subwoofer installation
- 22 Surface mount speakers
- 22 Surface mount satellite speaker installation
- 23 Wall bracket range of motion
- 23 Surface mount subwoofer installation
- 25 Removing subwoofer from the wall
- 26 Wiring
- 26 Ceiling mount speakers
- 26 Wattage tap
- 27 70v/100v/4 ohm Mono
- 28 Surface mount speakers
- 28 Wattage tap
- 29 70v/100v/4 ohm Mono
- 30 8 ohm Stereo Surface Mount Subwoofer Only
- 31 Troubleshooting
- 32 Technical data
- 32 Ceiling mount speakers
- 32 Frequency response
- 33 Surface Mount Speakers
- 33 Frequency response
- 34 Notes
- 36 Backpage