Huawei LTE CPE Online Help
Oglas
Oglas
Online Help
Welcome to the LTE CPE!
Online Help
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
Online Help
Copyright © Huawei Technologies Co., Ltd. 2014. All rights reserved.
No part of this document may be reproduced or transmitted in any form or by any means without prior written consent of Huawei Technologies Co., Ltd.
The product described in this manual may include copyrighted software of Huawei Technologies Co., Ltd and possible licensors. Customers shall not in any manner reproduce, distribute, modify, decompile, disassemble, decrypt, extract, reverse engineer, lease, assign, or sublicense the said software, unless such restrictions are prohibited by applicable laws or such actions are approved by respective copyright holders under licenses.
Trademarks and Permissions
, , and are trademarks or registered trademarks of Huawei Technologies Co., Ltd.
Other trademarks, product, service and company names mentioned are the property of their respective owners.
Notice
Some features of the product and its accessories described herein rely on the software installed, capacities and settings of local network, and may not be activated or may be limited by local network operators or network service providers, thus the descriptions herein may not exactly match the product or its accessories you purchase.
Huawei Technologies Co., Ltd reserves the right to change or modify any information or specifications contained in this manual without prior notice or obligation.
NO WARRANTY
THE CONTENTS OF THIS MANUAL ARE PROVIDED "AS IS". EXCEPT AS REQUIRED BY APPLICABLE
LAWS, NO WARRANTIES OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT
LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, ARE MADE IN RELATION TO THE ACCURACY, RELIABILITY OR
CONTENTS OF THIS MANUAL.
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, IN NO CASE SHALL HUAWEI
TECHNOLOGIES CO., LTD BE LIABLE FOR ANY SPECIAL, INCIDENTAL, INDIRECT, OR
CONSEQUENTIAL DAMAGES, OR LOST PROFITS, BUSINESS, REVENUE, DATA, GOODWILL OR
ANTICIPATED SAVINGS.
Import and Export Regulations
Customers shall comply with all applicable export or import laws and regulations and will obtain all necessary governmental permits and licenses in order to export, re-export or import the product mentioned in this manual including the software and technical data therein.
Copyright Notice
To view more details about the copyright notice of this product, please visit URL: http://consumer.huawei.com/minisite/copyright_notice/ or contact: [email protected].
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
Online Help Contents
Contents
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd i
Online Help Contents
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd ii
Online Help Contents
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd iii
Online Help 1 Getting Started
1
Getting Started
1.1 Welcome to the CPE
In this document, the LTE (Long Term Evolution) CPE (customer premises equipment) will be replaced by the CPE. Carefully read the following safety symbols to help you use your
CPE safely and correctly:
Additional information
Optional methods or shortcuts for an action
Potential problems or conventions that need to be specified
1.2 Computer Configuration Requirements
For optimum performance, make sure your computer meets the following requirements.
Item
CPU
Memory
Hard disk
Operating system
Display resolution
Browser
Requirement
Pentium 500 MHz or higher
128 MB RAM or higher
50 MB available space
Microsoft: Windows XP, Windows Vista, or Windows 7
Mac: Mac OS X 10.5 or higher
1024 x 768 pixels or higher
Internet Explorer 7.0 or later
Firefox 3.6 or later
Opera 10 or later
Safari 5 or later
Chrome 9 or later
1.3 Logging In to the Web Management Page
Use a browser to log in to the web management page to configure and manage the CPE.
The following procedure describes how to use a computer running Windows XP and Internet
Explorer 7.0 to log in to the web management page of the CPE.
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
1
Online Help 1 Getting Started
1. Connect the CPE properly.
2. Launch Internet Explorer, enter http://192.168.1.1 in the address bar, and press Enter.
3. Enter the user name and password, and click Log In.
You can log in to the web management page after the password is verified.
To protect your CPE from unauthorized access, change the password after your first login.
The CPE supports diagnostic function. If you encounter problems, please contact customer service for the specific using method.
Please change the default WiFi password as soon as possible.
To ensure your data safety, it is recommended that you turn on the firewall, and conserve your login, WiFi and FTP password carefully.
---End
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
2
Online Help 2 Home
2
Home
2.1 Overview
2.1.1 Viewing the Internet Status
To view the Internet connection status, perform the following steps:
1. Choose Home > Overview.
2. In the Internet Status area, view the Internet status, such as USIM card status, Network
mode, and IP address.
----End
2.1.2 Viewing the Internet Usage
To view the network data usage, perform the following steps:
1. Choose Home > Overview.
2. In the Internet Usage area, view the network data usage, including total traffic, uplink and downlink traffic volumes, uplink and downlink rates, and time spent online.
----End
2.1.3 Viewing the Wi-Fi Status
To view the Wi-Fi network connection status, perform the following steps:
1. Choose Home > Overview.
2. In the Wi-Fi Status area, view the following information.
View the Wi-Fi network connection status, including the SSID, IP Address, MAC Address,
Broadcast mode, and Wireless Encryption mode.
View the statistics of the Wi-Fi network, including the total traffic, packets, erroneous packets, and discarded packets transmitted and received over the Wi-Fi network.
----End
2.1.4 Viewing the LAN Usage
To view the local area network (LAN) connection status, perform the following steps:
1. Choose Home > Overview.
2. In the LAN Usage area, view the following information.
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
3
Online Help 2 Home
View the LAN status, such as IP address, MAC address, DHCP server.
View the statistics of the LAN, including the total traffic, packets, erroneous packets, and discarded packets transmitted and received over the LAN.
----End
2.1.5 Viewing the Antenna Status
To view the antenna status, perform the following steps:
1. Choose Home > Overview.
2. In the Antenna area, view the antenna status.
----End
2.2 Product Information
2.2.1 Viewing the Product Information
To view the basic product information, perform the following steps:
1. Choose Home > Product Information.
2. In the Product Information area, view the basic information about the CPE.
For example, the name, serial number (SN), international mobile equipment identity (IMEI).
----End
2.2.2 Viewing the Device List
To view the device list, perform the following steps:
1. Choose Home > Product Information.
2. In the Device List area, view the information about the devices, such as Computer Name,
MAC Address, IP Address, and Lease Time.
Lease Time indicates the remaining lease duration of the dynamic DHCP server. If a static IP address is bundled with the device, Lease Time and Computer Name are N/A and Unknown respectively.
----End
2.3 Quick Setup
The setup wizard guides you to configure the most important settings of the CPE. After the configurations are complete, the CPE can access the Internet.
To configure the CPE, perform the following steps:
1. Choose Home > Quick Setup.
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
4
Online Help 2 Home
2. Click Next to view and set Internet connection parameters.
3. Click Next to view and set Wi-Fi-related parameters, including Wi-Fi, Country/Region,
Mode, Channel, SSID, and Hide SSID broadcast.
4. Click Next to view and set Wi-Fi security-related parameters, such as Security.
The displayed parameters vary depending on the Security setting. For example, if Security is set to WPA-PSK&WPA2-PSK, then WPA-PSK and WPA encryption are displayed and must be set.
5. Click Next to view the settings you just configured.
6. Click Submit for the settings to take effect.
----End
2.4 Update
This function enables you to upgrade the software version of the CPE to the latest version. It is recommended that you update the software because in the new version, certain bugs have been fixed and the system stability is usually improved.
2.4.1 Updating on Local
To perform a local upgrade successfully, connect the CPE to your computer through Wi-Fi or a network cable, save the upgrade file on the computer, and make sure the CPE is not connected to anything other than a power adapter and the computer.
To perform a local upgrade, perform the following steps:
1. Choose Home > Update.
2. In the Local Update area, click Browse.
In the displayed dialog box, select the target software version file.
3. Click Open.
The dialog box closes. The save path and name of the target software version file are displayed in the Update file field.
4. Click Update.
During an upgrade, do not power off the CPE or disconnect it from the computer.
5. Click OK.
The software upgrade starts. After the upgrade, the CPE automatically restarts and runs the new software version.
----End
2.4.2 Updating Online
To perform an online upgrade successfully, make sure the CPE is connected to the Internet.
To perform an online upgrade, perform the following steps:
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
5
Online Help 2 Home
1. Choose Home > Update.
2. Click Check to detect the latest version.
After updates are found, the CPE retains the server address and informs you if any subsequent updates are found on the server.
If...
Then...
Updates are found.
Go to step 3.
Updates are not found.
The upgrade ends.
3. Click Update to download the updates.
After downloading the updates, the CPE automatically upgrades and restarts.
A message is displayed, indicating that the upgrade is complete. Then, the login dialog box is displayed.
During an upgrade, do not disconnect the power supply or operate the CPE.
---End
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
6
Online Help
3.1 Network Connection
3.1.1 Selecting a Network Mode
To select a network mode for the CPE, perform the following steps:
3 Internet
3
Internet
Insert a valid USIM card into the CPE.
Power on the CPE, and then log in to the web management page as the admin user.
1. Choose Internet > Network Connection.
2. Set Network mode to one of the following values:
Value
Auto
Description
The CPE automatically selects its working mode, with an order of preference of 4G, 3G and 2G.
4G
3G
The CPE accesses 4G networks only.
The CPE accesses 3G networks only.
2G
3. Click Submit.
----End
The CPE accesses 2G networks only.
3.1.2 Selecting a Connection Mode
To select a network connection mode, perform the following steps:
1. Choose Internet > Network Connection.
2. Set Connection mode.
Value
Always on
Description
If the conditions permit, the CPE automatically connects to the Internet.
Manual
When roaming, accessing the network automatically may incur additional charges.
The CPE disconnects from the Internet upon startup. You can connect or disconnect the CPE to or from the Internet manually.
3. Click Submit.
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
7
Online Help
----End
3.1.3 Selecting an APN Profile
You can select an APN profile for the CPE to access the Internet.
To set the APN profile, perform the following steps:
1. Choose Internet > Network Connection.
2. Select a profile from the Profile drop-down list.
3. Click Submit.
----End
3 Internet
3.1.4 Selecting PDP Type
You can select a PDP (Packet Data Protocol) to set the dial-up type, perform the following steps:
1. Choose Internet > Network Connection.
2. Set PDP type to one of the following values described in the following table:
Value
IPv4
Description
Internet Protocol version 4 (IPv4) that is the foundation for current Internet technologies. Because IP resources are limited, an IP address is shared by different persons in different time periods, that is, an IP address is not allocated to only one network subscriber. Thus, the real-name system cannot be implemented over the IPv4-based networks.
IPv4-to-IPv6 transition technology that is used when IPv4 and IPv6 coexist.
IPv4v6
3. Click Submit.
----End
3.1.5 Setting Data Roaming
To turn roaming on or off, perform the following steps:
1. Choose Internet > Network Connection.
2. Do as follows:
Select the Enable check box behind the Data Roaming to turn it on.
Clear the Enable check box behind the Data Roaming to turn it off.
3. Click Submit.
----End
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
8
Online Help
3.2 APN Management
To create an APN profile, perform the following steps:
1. Choose Internet >APN Management.
2. Click Add.
3. Set Profile name, APN, User Name and Password.
4. Set Authentication to None, PAP, CHAP or Auto.
5. Click Submit.
----End
To modify an APN profile, perform the following steps:
1. Choose Internet >APN Management.
2. Choose the APN profile item to be modified, and click Edit.
3. Modify Profile name, APN, User Name or Password.
4. Set Authentication to None, PAP, CHAP or Auto.
5. Click Submit.
----End
To delete an APN profile, perform the following steps:
1. Choose Internet >APN Management.
2. Choose the APN profile item to be deleted, and click Delete.
3. Click OK.
----End
3 Internet
3.3 PIN Management
To manage the PIN, You can perform the following operations on the PIN Management page:
Enable or disable the PIN verification
Verify the PIN
Chang the PIN
Set automatic verification of the PIN
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
9
Online Help
3.3.1 Viewing the Status of the USIM Card
To view the status of the USIM card, perform the following steps:
1. Choose Internet > PIN Management.
2. View the status of the USIM card in the USIM card status field.
----End
3.3.2 Enabling PIN Verification
To enable PIN verification, perform the following steps:
1. Choose Internet > PIN Management.
2. Set PIN verification to Enable.
3. Enter the PIN (4 to 8 digits) in the Enter PIN box.
4. Click Submit.
----End
3.3.3 Disabling PIN Verification
To disable PIN verification, perform the following steps:
1. Choose Internet > PIN Management.
2. Set PIN verification to Disable.
3. Enter the PIN (4 to 8 digits) in the Enter PIN box.
4. Click Submit.
----End
3 Internet
3.3.4 Verifying the PIN
If PIN verification is enabled but the PIN is not verified, the verification is required.
To verify the PIN, perform the following steps:
1. Choose Internet > PIN Management.
2. Enter the PIN (4 to 8 digits) in the PIN box.
3. Click Submit.
----End
3.3.5 Changing the PIN
The PIN can be changed only when PIN verification is enabled and the PIN is verified.
To change the PIN, perform the following steps:
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
10
Online Help 3 Internet
1. Choose Internet > PIN Management.
2. Set PIN verification to Enable.
3. Set Change PIN to Enable.
4. Enter the current PIN (4 to 8 digits) in the PIN box.
5. Enter a new PIN (4 to 8 digits) in the New PIN box.
6. Repeat the new PIN in the Confirm PIN box.
7. Click Submit.
----End
3.3.6 Setting Automatic Verification of the PIN
You can enable or disable automatic verification of the PIN. If automatic verification is enabled, the CPE automatically verifies the PIN after restarting. This function can be enabled only when PIN verification is enabled and the PIN is verified.
To enable automatic verification of the PIN, perform the following steps:
1. Choose Internet > PIN Management.
2. Set PIN verification to Enable.
3. Set Remember my PIN to Enable.
4. Click Submit.
----End
3.3.7 Verifying the PUK
If PIN verification is enabled and the PIN fails to be verified for three consecutive times, the
PIN will be locked. In this case, you need to verify the PUK and change the PIN to unlock it.
To verify the PUK, perform the following steps:
1. Choose Internet > PIN Management.
2. Enter the PUK in the PUK box.
3. Enter a new PIN in the New PIN box.
4. Repeat the new PIN in the Confirm PIN box.
5. Click Submit.
----End
3.4 Setting the Internet MTU
A maximum transmission unit (MTU) is defined as the maximum packet size (in bytes) at a communication protocol layer. It relates to communication ports, for example, network interface cards and serial ports.
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
11
Online Help
To set the MTU, perform the following steps:
1. Choose Internet > Internet MTU.
2. Set Internet MTU to a value in the range of 1280 to 1500.
3. Click Submit.
----End
3 Internet
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
12
Online Help 4 LAN
4
LAN
A local area network (LAN) is a shared communication system to which multiple devices are attached.
When correctly configured, devices on the LAN can use the CPE to share data.
4.1 DHCP Settings
4.1.1 Setting LAN Host Parameters
By default, the IP address is 192.168.1.1 with a subnet mask of 255.255.255.0. You can change the host IP address to another individual IP address that is easy to remember. Make sure that IP address is unique on your network. If you change the IP address of the CPE, you need to access the web management page with the new IP address.
To change the IP address of the CPE, perform the following steps:
1. Choose LAN > DHCP Settings.
2. In the LAN Host Settings area, set IP address.
3. Set the DHCP server to Enable.
4. Click Submit.
----End
4.1.2 Configuring the DHCP Server
DHCP enables individual clients to automatically obtain TCP/IP configuration when the server powers on.
You can configure the CPE as a DHCP server or disable it when the CPE is working in the routing mode.
When configured as a DHCP server, the CPE automatically provides the TCP/IP configuration for the LAN clients that support DHCP client capabilities. If DHCP server services are disabled, you must have another DHCP server on your LAN, or each client must be manually configured.
To configure DHCP settings, perform the following steps:
1. Choose LAN > DHCP Settings.
2. Set the DHCP server to Enable.
3. Set Start IP address.
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
13
Online Help 4 LAN
This IP address must be different from the IP address set on the LAN Host Settings area, but they must be on the same network segment.
4. Set End IP address.
This IP address must be different from the IP address set on the LAN Host Settings area, but they must be on the same network segment.
5. Set Lease time.
Lease time can be set to 1 to 10,080 minutes. It is recommended to retain the default value.
6. Click Submit.
----End
4.1.3 Bundled Address List
You can bind an IP address to a device based on its MAC address. The device will receive the same IP address each time it accesses the DHCP server. For example, you can bind an IP address to an FTP server on the LAN.
After you change the settings, click Submit for the changes to take effect. The
DHCP server may need to restart.
To add an item to the setup list, perform the following steps:
1. Choose LAN > DHCP Settings.
2. Click Edit List.
3. Click Add.
4. Set the MAC address and IP Address.
5. Click Submit.
----End
To modify an item in the setup list, perform the following steps:
1. Choose LAN > DHCP Settings.
2. Click Edit List.
3. Choose the item to be modified, and click Edit.
4. Set the MAC address and IP Address.
5. Click Submit.
----End
To delete an item in the setup list, perform the following steps:
1. Choose LAN > DHCP Settings.
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
14
Online Help 4 LAN
2. Click Edit List.
3. Choose the item to be deleted, and click Delete.
4. Click OK.
----End
To delete all items from the setup list, perform the following steps:
1. Choose LAN > DHCP Settings.
2. Click Edit List.
3. Click Delete All.
4. Click OK.
----End
4.2 Static Routing
If cascaded routers are used on the LAN, add static routing rules to ensure that the devices connected to the cascaded routers can be accessed. Static routing is similar to dynamic routing.
However, manual configuration is required and the router must always be available.
If the IP address of the cascaded router is fixed, static routing is recommended.
If the IP address of the cascaded router is changeable, dynamic routing is recommended.
To configure static routing settings, perform the following steps:
1. Choose LAN > Static Routing.
2. Click Add.
3. Set Destination IP address.
4. Set Subnet mask.
5. Set Router IP address.
This IP address is obtained from the CPE and used for data transmission to the cascading devices. This IP address must be reachable.
6. Click Submit.
----End
4.3 Dynamic Routing
This function is enabled when cascaded routers are used on the LAN and the cascaded routers comply with the Routing Information Protocol (RIP). This page allows you to enable or disable RIP and set its version and operation mode.
To configure dynamic routing settings, perform the following steps:
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
15
Online Help 4 LAN
1. Choose LAN > Dynamic Routing.
2. Set RIP to Enable.
3. Set Operation.
If it is set to Active, the CPE actively makes route changes and notifies surrounding routers of the changes. If it is set to Passive, the CPE does not make route changes until it is notified.
4. Set Version to RIP v1, RIP v2, or RIP v1/RIP v2.
5. Click Submit.
----End
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
16
Online Help 5 Wi-Fi
5
Wi-Fi
5.1 Wi-Fi Settings
This function enables you to configure the Wi-Fi parameters.
5.1.1 Setting General Parameters
To configure the general Wi-Fi settings, perform the following steps:
1. Choose Wi-Fi > Wi-Fi Settings.
2. In the General Settings area, set Wi-Fi to Enable.
3. Set Mode to one of the values described in the following table:
Parameter Value Description
802.11b/g The Wi-Fi client can connect to the CPE in 802.11b or 802.11g mode.
802.11g
802.11b
802.11b/g/n
The Wi-Fi client can connect to the CPE in 802.11g mode.
The Wi-Fi client can connect to the CPE in 802.11b mode.
The Wi-Fi client can connect to the CPE in 802.11b, 802.11g, or
802.11n mode. If the client connects to the CPE in 802.11n mode, the Advanced Encryption Standard(AES) encryption mode is required.
4. Click Submit.
----End
5.1.2 Setting SSID Profile
After you configure the CPE on the SSID Profile page, the Wi-Fi client connects to the CPE based on preset rules, improving access security.
To configure the CPE on the SSID Profile page, perform the following steps:
1. Choose Wi-Fi > Wi-Fi Settings.
2. Set SSID.
The SSID can contain 1 to 32 ASCII characters. It cannot be empty and the last character cannot be a blank character. In addition, the SSID cannot contain the following special characters: / ' = " \ &
The Wi-Fi client connects to the CPE using the found SSID.
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
17
Online Help 5 Wi-Fi
3. Set Maximum number of devices.
This parameter indicates the maximum number of Wi-Fi clients that connect to the
CPE.
A maximum of 32 clients can connect to the CPE.
4. Set Hide SSID broadcast to Enable.
If the SSID is hidden, the client cannot detect the CPE's Wi-Fi information.
5. Set AP isolation to Enable.
The clients can connect to the CPE but cannot communicate with each other.
6. Set Security.
If Security is set to NONE(not recommended), Wi-Fi clients directly connect to the CPE. This security level is low.
If Security is set to WEP, Wi-Fi clients connect to the CPE in web-based encryption mode.
If Security is set to WPA-PSK, Wi-Fi clients connect to the CPE in WPA-PSK encryption mode.
If Security is set to WPA2-PSK, Wi-Fi clients connect to the CPE in WPA2-PSK encryption mode. This mode is recommended because it has a high security level.
If Security is set to WPA-PSK & WPA2-PSK, Wi-Fi clients connect to the CPE in
WPA-PSK&WPA2-PSK encryption mode.
7. Set the encryption mode.
If…
WEP
Sets to
Authentication mode
Encryption password length
Description
Shared authentication: The client connects to the CPE in shared authentication mode.
Open authentication: The client connects to the CPE in open authentication mode.
Both: The client connects to the CPE in shared or open authentication mode.
128bit: Only 13 ASCII characters or 26 hex characters can be entered in the Key 1 to
Key 4 boxes.
64bit: Only 5 ASCII characters or 10 hex characters can be entered in the Key 1 to
Key 4 boxes.
Current password index
WPA-PSK WPA-PSK
WPA encryption
This value can be set to 1, 2, 3, or 4. After a key index is selected, the corresponding key takes effect.
Only 8 to 63 ASCII characters or 8 to 64 hex characters can be entered.
This value can be set to TKIP+AES, AES, or
TKIP.
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
18
Online Help
If…
WPA2-PSK(recom mended)
Sets to
WPA-PSK
WPA-PSK &
WPA2-PSK
5 Wi-Fi
Description
Only 8 to 63 ASCII characters or 8 to 64 hex characters can be entered.
WPA encryption This value can be set to TKIP+AES, AES, or
TKIP.
WPA-PSK Only 8 to 63 ASCII characters or 8 to 64 hex characters can be entered.
WPA encryption This value can be set to TKIP+AES, AES, or
TKIP.
8. Click Submit.
----End
5.2 Access Management
5.2.1 Setting the Access Policy
This function enables you to set access restriction policies for each SSID to manage access to the CPE.
To configure Wi-Fi MAC control settings, perform the following steps:
1. Choose Wi-Fi > Access Management.
2. In the Settings area, set SSID's MAC Access.
The MAC access of each SSID can be set to Disable, Blacklist or Whitelist.
If SSID's MAC Access is set to Disable, access restrictions do not take effect.
If SSID's MAC Access is set to Blacklist, only the devices that are not in the blacklist can connect to the CPE.
If SSID's MAC Access is set to Whitelist, only the devices in the whitelist can connect to the CPE.
3. Click Submit.
----End
5.2.2 Managing the Wi-Fi Access List
This function enables you to set the SSID access policies based on MAC addresses.
To add an item to the Wi-Fi access list, perform the following steps:
1. Choose Wi-Fi > Access Management.
2. Click Edit MAC List.
3. Click Add.
4. Set MAC address.
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
19
Online Help
5. Set one of the SSID to Enable to make the MAC address take effect for the SSID.
6. Click Submit.
----End
5 Wi-Fi
To modify an item in the Wi-Fi access list, perform the following steps:
1. Choose Wi-Fi > Access Management.
2. Click Edit MAC List.
3. Choose the item to be modified, and click Edit.
4. Set MAC address.
5. Set one of the SSID to Enable to make the MAC address take effect for the SSID.
6. Click Submit.
----End
To delete an item from the Wi-Fi access list, perform the following steps:
1. Choose Wi-Fi > Access Management.
2. Click Edit MAC List.
3. Choose the item to be deleted, and click Delete.
4. Click OK.
----End
To delete all items from the Wi-Fi access list, perform the following steps:
1. Choose Wi-Fi > Access Management.
2. Click Edit MAC List.
3. Click Delete All.
4. Click OK.
----End
5.3 WPS Settings
Wi-Fi Protected Setup (WPS) enables you to simply add a wireless client to the network without needing to specifically configure the wireless settings, such as the SSID, security mode and passphrase. You can use either the WPS button or PIN to add the wireless client.
To configure Wi-Fi WPS settings, perform the following steps:
1. Choose Wi-Fi > WPS Settings.
2. Set WPS to Enable.
3. Set WPS Mode.
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
20
Online Help 5 Wi-Fi
If WPS Mode is set to PBC, the client can connect to the CPE after you press the
WPS button on the CPE and the client.
If WPS Mode is set to Route PIN, the client can connect to the CPE after you enter the Router PIN on the client.
If WPS Mode is set to Client PIN, the client can connect to the CPE after you enter the correct PIN and click Connect to Client.
4. Click Submit.
----End
5.4 Wi-Fi Multi-SSID Settings
The SSID List page shows information about the SSIDs to be configured.
To configure an SSID, perform the following steps:
1. Choose Wi-Fi > Wi-Fi Multi-SSID.
2. Choose an SSID to be configured, and click Edit.
3. Set Status to Enable.
4. Set SSID.
The SSID can contain 1 to 32 ASCII characters. It cannot be empty and the last character cannot be a blank character. In addition, the SSID cannot contain the following special characters: / ' = " \ &
5. Set Maximum number of devices.
This parameter indicates the maximum number of Wi-Fi clients that connect to the
CPE.
A maximum of 32 clients can connect to the CPE.
6. Set Hide SSID broadcast to Enable.
If the SSID is hidden, the client cannot detect the CPE's Wi-Fi information.
7. Set AP isolation to Enable.
The clients can connect to the CPE but cannot communicate with each other.
8. Set Security.
If Security is set to WPA-PSK, WPA2-PSK or WPA-PSK & WPA2-PSK, you can set
WPA encryption and WPA-PSK.
WPA-PSK can contain 8 to 63 ASCII characters or 64 hex characters.
If Security is set to WEP, set Authentication mode, Password length and Current
password index, and configure the corresponding keys.
If Password length is set to 128-bit, the 128-bit encryption key must contain 13 ASCII characters or 26 hex characters.
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
21
Online Help
If Password length is set to 64-bit, the 64-bit encryption key must contain 5 ASCII characters or 10 hex characters.
9. Click Submit.
5 Wi-Fi
----End
5.5 Advanced Settings
Advanced Settings affect Wi-Fi performance. The settings help you to obtain the maximum rate through optimal access performance.
To configure the advanced settings, perform the following steps:
1. Choose Wi-Fi > Advanced Settings.
2. Set Country/Region.
3. Set Channel.
Auto indicates that the channel with the best signal quality is selected.
The value 1 to 13 indicates the selected channel.
4. Set 802.11n bandwidth.
If this parameter is set to 20MHz, 802.11n supports only 20 MHz bandwidth.
If this parameter is set to 20/40MHz, 802.11n supports 20 MHz or 40 MHz bandwidth.
5. Set Transmit power.
If this parameter is set to 100%, the Wi-Fi client transmits at full power.
If this parameter is set to 80%, 60%, or 40%, the Wi-Fi client transmits signals at low power. The Wi-Fi client located far away from the CPE may fail to access the
CPE.
6. Set WMM to Enable.
Wi- Fi Multimedia (WMM) is a Wi-Fi Alliance interoperability certification based on the
IEEE 802.11e standard. It provides basic quality of service (QoS) features for IEEE 802.11 networks. WMM prioritizes traffic according to four access categories (AC): voice, video, best effort, and background. However, WMM does not provide guaranteed throughput. WMM applies to simple applications that require QoS, such as Voice over IP (VoIP) on Wi-Fi phones.
7. Click Submit.
----End
5.6 WDS
The CPE supports the wireless distribution system
(
WDS
)
. All Wi-Fi devices in a WDS must be configured to use the same radio channel, encryption mode, SSID, and encryption key. You
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
22
Online Help 5 Wi-Fi can set the WDS encryption mode to NONE or WPA/WPA2. If you set the WDS encryption mode to NONE, the Wi-Fi clients can use NONE or WEP encryption mode. If you set the
WDS encryption mode to WPA/WPA2-PSK, the Wi-Fi clients can use WPA/WPA2-PSK encryption mode. After WDS is enabled, disable DHCP on CPEs that are not directly connected to the WAN port.
If WDS is enabled, the WPS function will not take effect. If the channel is set to
Auto, go to the Advanced Settings page to set the channel.
To configure the WDS, perform the following steps:
1. Choose Wi-Fi > WDS.
2. Set WDS to Enable.
3. Click Scan.
4. From the search results, choose the SSID of the networking device.
5. Set Security.
WPA-PSK can contain 8 to 63 ASCII characters or 64 hex characters.
6. Click Submit.
----End
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
23
Online Help 6 Security
6
Security
6.1 Setting Firewall Level
This page describes how to set the firewall level. If Firewall level is set to Custom, you can modify the configuration.
To set the firewall level, perform the following steps:
1. Choose Security > Firewall Level.
2. Set Firewall level from the drop-down list.
3. Set DoS attack to Enable.
To block Denial of Service (DoS) attacks from the LAN and Internet.
4. Click Submit.
----End
To set filtering functions of the firewall, perform the following steps:
1. Choose Security > Firewall Level.
2. Set Firewall level to Custom.
3. Set MAC filtering.
4. Set IP filtering.
5. Set URL filtering.
6. Click Submit.
----End
6.2 MAC Filtering
This page enables you to configure the MAC address filtering rules.
6.2.1 Managing MAC Address Whitelist
To add a MAC address whitelist rule, perform the following steps:
1. Choose Security > MAC Filtering.
2. Set MAC filtering mode to Whitelist.
3. Click Add Item.
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
24
Online Help 6 Security
4. Set the MAC address.
5. Click Submit.
----End
To modify a MAC address rule, perform the following steps:
1. Choose Security > MAC Filtering.
2. Set MAC filtering mode to Whitelist.
3. Choose the rule to be modified, and click Edit.
4. Set MAC address.
5. Click Submit.
----End
To delete a MAC address whitelist rule, perform the following steps:
1. Choose Security > MAC Filtering.
2. Set MAC filtering mode to Whitelist.
3. Choose the rule to be deleted, and click Delete.
4. Click OK.
----End
To delete all MAC address whitelist rules, perform the following steps:
1. Choose Security > MAC Filtering.
2. Set MAC filtering mode to Whitelist.
3. Click Delete All.
4. Click OK.
----End
6.2.2 Managing MAC Address Blacklist
Choose Security > MAC Filtering, and then set MAC filtering mode to Blacklist.
The other steps are the same as those for managing the MAC address whitelist. For details, see section "Managing MAC Address Whitelist".
6.3 URL Filtering
Data is filtered by uniform resource locator (URL). This page enables you to configure URL filtering rules.
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
25
Online Help
6.3.1 Managing URL Whitelist
To add a URL whitelist rule, perform the following steps:
1. Choose Security > URL Filtering.
2. Set URL filtering mode to Whitelist.
3. Click Add Item.
4. Set URL.
5. Click Submit.
----End
To modify a URL whitelist rule, perform the following steps:
1. Choose Security > URL Filtering.
2. Set URL filtering mode to Whitelist.
3. Choose the rule to be modified, and click Edit.
4. On the displayed page, set URL.
5. Click Submit.
----End
To delete a URL whitelist rule, perform the following steps:
1. Choose Security > URL Filtering.
2. Set URL filtering mode to Whitelist.
3. Choose the rule to be deleted, and click Delete.
4. Click OK.
----End
6 Security
To delete all URL whitelist rules, perform the following steps:
1. Choose Security > URL Filtering.
2. Set URL filtering mode to Whitelist.
3. Click Delete All.
4. Click OK.
----End
6.3.2 Managing URL Blacklist
Choose Security > URL Filtering, and then set URL filtering mode to Blacklist.
The other steps are the same as those for managing the URL address whitelist. For details, see section "Managing URL Whitelist".
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
26
Online Help 6 Security
6.4 IP Filtering
Data is filtered by IP address. This page enables you to configure the IP address filtering rules.
6.4.1 Managing IP Address Whitelist
To add an IP address whitelist rule, perform the following steps:
1. Choose Security > IP Filtering.
2. Set IP filtering mode to Whitelist.
3. Click Add Item.
4. Set Service.
5. Set Protocol.
6. In the Source IP Address Range box, enter the source IP address or IP address segment to be filtered.
7. In the Source port range box, enter the source port or port segment to be filtered.
8. In the Destination IP Address Range box, enter the destination IP address or IP address segment to be filtered.
9. In the Destination port Range box, enter the destination port or port segment to be filtered.
10. Click Submit.
----End
To modify an IP whitelist rule, perform the following steps:
1. Choose Security > IP Filtering.
2. Set IP filtering mode to Whitelist.
3. Choose the rule to be modified, and click Edit.
4. Repeat steps 4 through 9 in the previous procedure.
5. Click Submit.
----End
To delete an IP address whitelist rule, perform the following steps:
1. Choose Security > IP Filtering.
2. Set IP filtering mode to Whitelist.
3. Choose the rule to be deleted, and click Delete.
4. Click OK.
----End
To delete all IP whitelist rules, perform the following steps:
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
27
Online Help 6 Security
1. Choose Security > IP Filtering.
2. Set IP filtering mode to Whitelist.
3. Click Delete All.
4. Click OK.
----End
6.4.2 Managing IP Blacklist
Choose Security > IP Filtering, and then set IP filtering mode to Blacklist.
The other steps are the same as those for managing the IP address whitelist. For details, see section "Managing IP Address Whitelist".
6.5 Setting Service Access Control
This function enables you to control the number of users connecting to the CPE.
The access control list shows the types of services that are controlled by the CPE. By default, the access control rules are not in effect.
To set the access control list, perform the following steps:
1. Choose Security > Service Access Control.
2. Choose the item to be configured, and click Edit.
3. Set IP address range.
If Access Source is set to LAN, the IP address must be on the same network segment as the IP address set on the LAN Host Settings page.
If Access Source is set to Internet, the IP address must be on different network segments from the IP address that is set on the LAN Host Settings page.
4. Set Status.
5. Click Submit.
----End
6.6 Setting ALG
To enable ALG(Application Layer Gateway), perform the following steps:
1. Choose Security > ALG.
2. Set SIP ALG to Enable.
3. Set SIP port.
It is recommended to retain the default port 5060. If you use another port, you cannot use VoIP software.
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
28
Online Help 6 Security
4. Click Submit.
----End
6.7 Setting Port Forwarding
When network address translation (NAT) is enabled on the CPE, only the IP address on the
WAN side is open to the Internet. If a computer on the LAN is enabled to provide services for the Internet (for example, work as an FTP server), port forwarding is required so that all accesses to the external server port from the Internet are redirected to the server on the LAN.
To add a port forwarding rule, perform the following steps:
1. Choose Security > Port Forwarding.
2. Click Add Item.
3. Set Type.
4. Set Protocol.
5. (Optional) Set Remote host.
6. Set Remote port range.
The port number ranges from 1 to 65535.
7. Set Local host.
This IP address must be different from the IP address that is set on the LAN Host
Settings page, but they must be on the same network segment.
8. Set Local port.
The port number ranges from 1 to 65535.
9. Set Status to Enabled or Disabled.
10. Click Submit.
----End
To modify a port forwarding rule, perform the following steps:
1. Choose Security > Port Forwarding.
2. Choose the item to be modified, and click Edit.
3. Repeat steps 3 through 9 in the previous procedure.
4. Click Submit.
----End
To delete a port forwarding rule, perform the following steps:
1. Choose Security > Port Forwarding.
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
29
Online Help 6 Security
2. Choose the item to be deleted, and click Delete.
3. Click OK.
----End
To delete all port forwarding rules, perform the following steps:
1. Choose Security > Port Forwarding.
2. Click Delete All.
3. Click OK.
----End
6.8 Setting UPnP
On this page, you can enable or disable the Universal Plug and Play (UPnP)function.
To enable UPnP, perform the following steps:
1. Choose Security > UPnP.
2. Set UPnP to Enable.
3. Click Submit.
----End
6.9 Setting DMZ
If the demilitarized zone (DMZ) is enabled, the packets sent from the WAN are directly sent to a specified IP address on the LAN before being discarded by the firewall.
To set DMZ, perform the following steps:
1. Choose Security > DMZ.
2. Set DMZ to Enable.
3. Set Host address.
This IP address must be different from the IP address set on the LAN Host Settings page, but they must be on the same network segment.
4. Click Submit.
----End
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
30
Online Help 7 Services
7
Services
7.1 Setting DDNS
Dynamic Domain Name Server (DDNS) service is used to map the user's dynamic IP address to a fixed DNS service.
To configure DDNS settings, perform the following steps:
1. Choose Services > DDNS.
2. In Service provider, choose DynDNS.org.
3. Set DDNS to Enable.
4. Enter Domain name and Host name.
For example, if the domain name provided by your service provider is
test.customtest.dyndns.org, enter customtest.dyndns.org as Domain name, and test as
Host name.
5. Enter User name and Password.
6. Click Submit.
----End
7.2 SMS Management
7.2.1 Viewing SMS Messages
You can check the messages in your inbox, drafts, and outbox folders.
To view a message, perform the following steps:
1. Choose Services > SMS Messages.
2. Do as follows:
Click Inbox to view received messages.
Click Drafts to view draft messages.
Click Outbox to view sent messages.
----End
7.2.2 Sending SMS Messages
To send a message, perform the following steps:
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
31
Online Help 7 Services
1. Choose Services > SMS Messages.
2. In Phone number, enter the recipient's phone number.
If you want to send a message to multiple recipients, use semicolons (;) to separate the phone numbers.
3. In Content, edit a message.
4. Click Send.
----End
7.2.3 Saving SMS Messages
To save a message, perform the following steps:
1. Choose Services > SMS Messages.
2. In Phone number, enter the recipients' phone numbers.
3. In Content, edit a message.
4. Click Save.
----End
7.2.4 Forwarding SMS Messages
To forward a message, perform the following steps:
1. Choose Services > SMS Messages.
2. Choose the message to be forwarded, and click Forward.
3. In Phone number, enter the recipients' phone numbers.
4. Click Send.
----End
7.2.5 Replying to SMS Messages
To reply to a message, perform the following steps:
1. Choose Services > SMS Messages.
2. Choose the message to be replied, and click Reply.
3. In Content, edit a message.
4. Click Send.
----End
7.2.6 Deleting SMS Messages
To delete one or more SMS messages, perform the following steps:
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
32
Online Help 7 Services
1. Choose Services > SMS Messages.
2. Do as follows:
Choose the message to be deleted, and click Delete.
To delete all messages on a page, click Delete Page.
----End
7.3 Setting SMS
You can configure SMS settings, such as setting the SMS center number, enabling or disabling an SMS report, and setting whether to save sent messages.
1. Choose Services > SMS Settings.
2. In the Service center address box, enter the SMS center number.
3. Set whether to enable SMS report.
4. Set whether to enable Save sent messages.
A message sent to multiple recipients cannot be saved.
5. Select the save time from the drop-down list.
6. Click Submit.
----End
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
33
Online Help 8 Voice
8
Voice
The CPE supports voice services based on the Session Initiation Protocol (SIP) and enables voice service interworking between the Internet and Public Switched Telephone Networks
(PSTNs).
8.1 Viewing Voice Information
To view the Voice information, perform the following steps:
1. Choose Voice > Voice Information.
2. View the Voice information, such as the SIP account and status of the SIP registration server.
----End
8.2 Configuring a SIP Server
To set the SIP server parameters, perform the following steps:
1. Choose Voice > SIP Server.
2. In the Proxy server address box, enter the address of the proxy server provided by your service provider, for example, 192.168.1.10.
3. In the Proxy server port box, enter the port of the proxy server provided by your service provider, for example, 5060.
The value ranges from 1 to 65535.
4. In the Registration server address box, enter the address of the registration server provided by your service provider, for example, 192.168.1.11.
5. In the Registration server port box, enter the port of the registration server provided by your service provider, for example, 5060.
The value ranges from 1 to 65535.
6. In the SIP server domain name box, enter the domain name of the SIP server.
If you set Secondary server to Enable, you should set the previous parameters again.
7. Click Submit.
----End
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
34
Online Help 8 Voice
8.3 Configuring a SIP Account
Before configuring SIP accounts, make sure that the registration server has been properly configured.
To add a SIP account, perform the following steps:
1. Choose Voice > SIP Account.
2. Click Add Item.
3. In the SIP Account box, enter the SIP account number provided by your service provider.
4. In the User name and Password boxes, enter the user name and password of the SIP account provided by your service provider.
5. Click Submit.
----End
To modify a SIP account, perform the following steps:
1. Choose Voice > SIP Account.
2. Choose the item to be modified, and click Edit.
3. Repeat steps 3 and 4 in the previous procedure.
4. Click Submit.
----End
To delete a SIP account, perform the following steps:
1. Choose Voice > SIP Account.
2. Choose the item to be deleted, and click Delete.
3. Click OK.
----End
To delete all SIP accounts, perform the following steps:
1. Choose Voice > SIP Account.
2. Click Delete All.
3. Click OK.
----End
8.4 Managing Speed Dial
Speed dial enables you to quickly dial a telephone number. Once you assign a speed dial number to a telephone number, you can use the former to dial the latter. You can configure up to 10 speed dial numbers.
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
35
Online Help 8 Voice
To add a speed dial number, perform the following steps:
1. Choose Voice > Speed Dial.
2. Click Add Item.
3. In the Speed Dial Number box, enter an easily remembered number.
4. In the Actual Number box, enter the actual telephone number.
5. In the Description box, enter a description for the speed dial number.
6. Click Submit.
----End
To modify a speed dial number, perform the following steps:
1. Choose Voice > Speed Dial.
2. Choose the item to be modified, and click Edit.
3. Repeat steps 3 through 5 in the previous procedure.
4. Click Submit.
----End
To delete a speed dial number, perform the following steps:
1. Choose Voice > Speed Dial.
2. Choose the number to be deleted, and click Delete.
3. Click OK.
----End
To delete all speed dial numbers, perform the following steps:
1. Choose Voice > Speed Dial.
2. Click Delete All.
3. Click OK.
----End
8.5 Setting Advanced Voice Parameters
On the Advanced Voice page, you can set advanced voice parameters. It is recommended that you retain the default settings.
To set the advanced voice parameters, perform the following steps:
1. Choose Voice > Advanced Voice.
2. Set the following parameters:
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
36
Online Help
8 Voice
DTMF Method: specifies the Dual Tone Multi-Frequency (DTMF) transmission mode.
Fax Option: specifies the Fax over IP mode.
Country/Region: specifies the country or region where the CPE is located.
If you change the Country/Region settings, you must restart the CPE for the settings to take effect.
Primary voice domain: specifies the primary domain.
3. Click Submit.
----End
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
37
Online Help 9 System
9
System
9.1 Maintenance
9.1.1 Restart
This function enables you to restart the CPE. Settings take effect only after the CPE restarts.
To restart the CPE, perform the following steps:
1. Choose System > Maintenance.
2. Click Restart.
3. Click OK.
The CPE then restarts.
----End
9.1.2 Reset
This function enables you to restore the CPE to its default settings.
To restore the CPE, perform the following steps:
1. Choose System > Maintenance.
2. Click Reset.
3. Click OK.
The CPE is then restored to its default settings.
----End
9.1.3 Downloading a Configuration File
You can download the existing configuration file to back it up. To do so:
1. Choose System > Maintenance.
2. Click Download on the Maintenance page.
In the displayed dialog box, select the save path and name of the configuration file to be backed up.
3. Click Save.
The procedure for file downloading may vary with the browser you are using.
----End
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
38
Online Help 9 System
9.1.4 Uploading a Configuration File
You can upload a backed up configuration file to restore the CPE. To do so:
1. Choose System > Maintenance.
2. Click Browse on the Maintenance page.
In the displayed dialog box, select the backed up configuration file.
3. Click Open.
The dialog box closes. In the box to the right of Configuration file, the save path and name of the backed up configuration file are displayed.
4. Click Upload.
5. Click OK.
The CPE uploads the backed up configuration file. The CPE then automatically restarts.
----End
9.2 Changing the Password
This function enables you to change the login password of the admin user. After the password changes, enter the new password the next time you log in.
To change the password, perform the following steps:
1. Choose System > Change Password.
2. Enter the current password, set a new password, and confirm the new password.
New password and Confirm password must contain 8 to 15 ASCII characters.
3. Click Submit.
----End
9.3 Setting the Date and Time
You can set the system time manually or synchronize it with the network. If you select Sync
from network, the CPE regularly synchronizes the time with the specified Network Time
Protocol (NTP) server. If you enable daylight saving time (DST), the CPE also adjusts the system time for DST.
To set the date and time, perform the following steps:
1. Choose System > Date & Time.
2. Select Set manually.
3. Set Local time or click Sync from PC to automatically fill in the current local system time.
4. Click Submit.
----End
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
39
Online Help 9 System
To synchronize the time with the network, perform the following steps:
1. Choose System > Date & Time.
2. Select Sync from network.
3. From the Primary NTP server drop-down list, select a server as the primary server for time synchronization.
4. From the Secondary NTP server drop-down list, select a server as the IP address of the secondary server for time synchronization.
5. Set Time zone.
6. Select Daylight saving time.The CPE automatically provides the default DST time based on the time zone.
7. Click Submit.
----End
9.4 Diagnosis
If the CPE is not functioning correctly, you can use the diagnosis tools on the Diagnosis page to preliminarily identify the problem so that actions can be taken to solve it.
9.4.1 Ping
If the CPE fails to access the Internet, run the ping command to preliminarily identify the problem. To do so:
1. Choose System > Diagnosis.
2. In the Method area, select Ping.
3. Enter the domain name in the Target IP or domain field, for example, www.google.com.
4. Set Packet size and Timeout.
5. Set Do not fragment to Enable.
6. Click Ping.
Wait until the ping command is executed. The execution results are displayed in the Results box.
----End
9.4.2 Traceroute
If the CPE fails to access the Internet, run the Traceroute command to preliminarily identify the problem. To do so:
1. Choose System > Diagnosis.
2. In the Method area, select Traceroute.
3. Enter the domain name in the Target IP or domain field.
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
40
Online Help 9 System
For example, www.google.com.
4. Set Maximum hops and Timeout.
5. Click Traceroute.
Wait until the traceroute command is executed. The execution results are displayed in the
Results box.
----End
9.4.3 System Check
If the CPE malfunctions, you can use the System Check tool to preliminarily identify the problem. To do so:
1. Choose System > Diagnosis.
2. In the Method area, select System check.
3. Click Check.
Wait until the system check is performed. The possible causes of the CPE problem are displayed on the page.
4. Click Export to export the detailed information to the computer.
If necessary, send the detailed information to maintenance personnel.
----End
9.4.4 Checking the Wireless Status
This page displays information about the wireless network status, such as the PLMN, service
status.
To view the wireless status, perform the following steps:
1. Choose System > Diagnosis.
2. In the Method area, select Wireless status check.
The Wireless Status page is displayed.
----End
9.5 Logs
Logs record user operations and key running events. To view logs:
1. Choose System > Logs.
2. Select the corresponding log level from the Log level drop-down list.
The number of logs in this level is displayed to the right of the drop-down list, and all logs are displayed in the output box.
3. Select the operation mode.
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
41
Online Help 9 System
Clear: Clear all logs in the CPE.
Export: Export all logs in the CPE to a file in the computer.
----End
9.6 System Notification
This page enables you to configure the notification methods of key device status changes.
1. Choose System > System Notification.
2. Set Frequency from the drop-down list.
Set Web popup receiving IP. If Web popup receiving IP is left blank, notifications are randomly sent to connected clients.
3. Set Send SMS notification to, and Forward SMS from.
After Send SMS notification to setting takes effect, message test, forwarding, and notification settings can be configured.
4. Configure the notification settings for each Events.
5. Click Submit.
----End
9.7 Setting TR-069
TR-069 is a standard for communication between CPEs and the auto-configuration server
(ACS). If your service provider uses the TR-069 automatic service provision function, the
ACS automatically provides the CPE parameters. If you set the ACS parameters on both the
CPE and ACS, the network parameters on the CPE are automatically set using the TR-069 function, and you do not need to set other parameters on the CPE.
To configure the CPE to implement the TR-069 function, perform the following steps:
1. Choose System > TR-069 Settings.
2. To enable the CPE to send inform packets to the ACS at predefined intervals, set Periodic
inform to Enable.
3. If you set Periodic inform to Enable, set Periodic inform interval.
4. In the ACS URL box, enter the ACS URL address.
5. Enter ACS user name and ACS password for CPE authentication.
To use the CPE to access the ACS, you must provide a user name and password for authentication. The user name and the password must be the same as those defined on the ACS.
6. Click Submit.
----End
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
42
Online Help
9.8 Setting Antenna
To set the antenna type, perform the following steps:
1. Choose System > Antenna Settings.
2. Select the antenna type from the drop-down list.
3. Click Submit.
----End
9 System
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
43
Online Help 10 FAQs
10
FAQs
The POWER indicator does not turn on.
Make sure that the power cable is connected properly and the CPE is powered on.
Make sure that the power adapter is compatible with the CPE.
Fails to Log in to the web management page.
Make sure that the CPE is started.
Verify that the CPE is correctly connected to the computer through Wi-Fi or a network cable.
If the problem persists, contact authorized local service suppliers.
The CPE fails to search for the wireless network.
Check that the power adapter is connected properly.
Check that the CPE is placed in an open area that is far away from obstructions, such as concrete or wooden walls.
Check that the CPE is placed far away from household electrical appliances that generate strong electromagnetic field, such as microwave ovens, refrigerators, and satellite dishes.
If the problem persists, contact authorized local service suppliers.
The power adapter of the CPE is overheated.
The CPE will be overheated after being used for a long time. Therefore, power off the CPE when you are not using it.
Check that the CPE is properly ventilated and shielded from direct sunlight.
The parameters are restored to default values.
If the CPE powers off unexpectedly while being configured, the parameters may be restored to the default settings.
After configuring the parameters, download the configuration file to quickly restore the CPE to the desired settings.
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
44
IP
IPSec
ISP
LAN
LTE
MAC
MTU
NAT
NTP
DoS
DST
FTP
GSM
GUI
HTTP
ICMP
IMEI
ACL
AES
ALG
AP
CPE
CWMP
DDNS
DDoS
DHCP
DMZ
DNS
Online Help 11 Acronyms and Abbreviations
11
Acronyms and Abbreviations
Access Control List
Advanced Encryption Standard
Application Layer Gateway
Access Point
Customer-Premises Equipment
CPE WAN Management Protocol
Dynamic Domain Name Server
Distributed Denial of Service
Dynamic Host Configuration Protocol
Demilitarized Zone
Domain Name Server/Domain Name System
Denial-of-Service
Daylight Saving Time
File Transfer Protocol
Global System for Mobile Communications
Graphical User Interface
Hypertext Transfer Protocol
Internet Control Message Protocol
International Mobile Station Equipment Identity
Internet Protocol
Internet Protocol Security
Internet Service Provider
Local Area Network
Long Term Evolution
Media Access Control
Maximum Transmission Unit
Network Address Translation
Network Time Protocol
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
45
Online Help
SN
SNTP
SSID
SSH
SYN
TKIP
TLS
TTLS
UDP
UPnP
URL
PBC
PIN
PKM
PPPoE
PPTP
RIP
RTSP
QoS
SIM
SIP
VLAN
VoIP
WAN
WCDMA
WEP
WLAN
WPA
WPA-PSK
WPS
Push Button Configuration
Personal Identification Number
Privacy Key Management
Point-to-Point Protocol over Ethernet
Point-to-Point Tunneling Protocol
Routing Information Protocol
Real Time Streaming Protocol
Quality of Service
Subscriber Identity Module
Session Initiation Protocol
Serial Number
Simple Network Time Protocol
Service Set Identifier
Secure Shell
Synchronous Idle
Temporal Integrity Protocol
Transport Layer Security
Tunneled Transport Layer Security
User Datagram Protocol
Universal Plug and Play
Uniform Resource Locator
Virtual Local Area Network
Voice over Internet Protocol
Wide Area Network
Wideband Code Division Multiple Access
Wired Equivalent Privacy
Wireless Local Area Network
Wi-Fi Protected Access
Wi-Fi Protected Access-Pre-Shared Key
Wi-Fi Protected Setup
11 Acronyms and Abbreviations
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
46
Prenesi
Javna povezava posodobljena
Javna povezava do vašega klepeta je bila posodobljena. You may view and manage your chat links after registration here.
Javna povezava do dokumenta
Oglas