HUAWEI B2328-42 V100R001C00 LTE CPE User Guide

PDF

Dokument

LTE TDD B2328-42

V100R001C00

User Guide

Issue

Date

2016-07-10

HUAWEI TECHNOLOGIES CO., LTD.

No part of this document may be reproduced or transmitted in any form or by any means without prior written consent of Huawei Technologies Co., Ltd.

Trademarks and Permissions

and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd.

All other trademarks and trade names mentioned in this document are the property of their respective holders.

Notice

The purchased products, services and features are stipulated by the contract made between Huawei and the customer. All or part of the products, services and features described in this document may not be within the purchase scope or the usage scope. Unless otherwise specified in the contract, all statements, information, and recommendations in this document are provided "AS IS" without warranties, guarantees or representations of any kind, either express or implied.

The information in this document is subject to change without notice. Every effort has been made in the preparation of this document to ensure accuracy of the contents, but all statements, information, and recommendations in this document do not constitute a warranty of any kind, express or implied.

Huawei Technologies Co., Ltd.

Address: Huawei Industrial Base

Bantian, Longgang

Shenzhen 518129

People's Republic of China

Website: http://www.huawei.com

Email: [email protected]

Content

Contents ............................................................................................................................................ ii

1 About this Guide ........................................................................................................................... 1

1.1 Prerequisite Skills and Knowledge ............................................................................................................................... 1

1.2 Conventions Used in this Document ............................................................................................................................. 1

2 Introduction.................................................................................................................................... 3

2.1 Product Overview ......................................................................................................................................................... 3

2.2 Product Package............................................................................................................................................................ 3

2.3 Connectors .................................................................................................................................................................... 4

2.4 LED Indicators.............................................................................................................................................................. 5

2.5 Installation .................................................................................................................................................................... 7

2.5.1 Installing LTE Outdoor CPE ...................................................................................................................................... 7

2.5.2 Connecting the Cable ................................................................................................................................................. 9

3 Web Interface ............................................................................................................................... 11

3.1 Login to Web-GUI ...................................................................................................................................................... 11

3.2 Function Button .......................................................................................................................................................... 13

3.3 Status and device information ..................................................................................................................................... 15

3.3.1 Status> Device Status .............................................................................................................................................. 15

3.3.2 Status> Modem Status ............................................................................................................................................. 17

3.3.3 Status> Telephony Status ......................................................................................................................................... 20

3.3.4 Status> About ........................................................................................................................................................... 20

3.3.5 Status> Help............................................................................................................................................................. 21

3.4 Menu Structure ........................................................................................................................................................... 21

4 Reference Manual ....................................................................................................................... 23

4.1 Management ............................................................................................................................................................... 23

4.1.1 Management >Setup Wizard .................................................................................................................................... 23

4.1.2 Management>Modem Setup .................................................................................................................................... 26

4.1.3 Management>WAN Setup ....................................................................................................................................... 28

4.1.4 Management>LAN Setup ........................................................................................................................................ 32

4.1.5 Management>IPv6 ................................................................................................................................................... 35

4.1.6 Management> Telephony......................................................................................................................................... 39

4.1.7 Management>Diagnostics ....................................................................................................................................... 47

Issue 01 (2015-07-10) Huawei Proprietary and Confidential

4.1.8 Management> System Log ...................................................................................................................................... 49

4.2 Personalization ............................................................................................................................................................ 51

4.2.1 Personalization>PIN Management .......................................................................................................................... 51

4.2.2 Personalization>Configuration ................................................................................................................................ 54

4.2.3 Personalization>Device Setup ................................................................................................................................. 55

4.2.4 Personalization>Software ........................................................................................................................................ 58

5 Reference Manual ....................................................................... Error! Bookmark not defined.

5.1 Basic>Firewall ............................................................................................................................................................ 60

5.2 Basic>DMZ ................................................................................................................................................................ 62

5.3 Basic>UPnP ................................................................................................................................................................ 63

5.4 Basic>Dynamic DNS .................................................................................................................................................. 64

5.5 Basic>VPN Passthrough ............................................................................................................................................. 65

6 Reference Manual ....................................................................... Error! Bookmark not defined.

6.1 Advanced>MAC Filtering .......................................................................................................................................... 67

6.2 Advanced>IP Filtering ................................................................................................................................................ 68

6.3 Advanced>Port Forwarding ........................................................................................................................................ 70

6.4 Advanced>Port Trigger ............................................................................................................................................... 71

6.5 Advanced>Layer 7 ...................................................................................................................................................... 73

6.6 Advanced>URL Filtering............................................................................................................................................ 74

6.7 Advanced>ACL Filtering............................................................................................................................................ 75

6.8 Advanced>Static Routing ........................................................................................................................................... 78

7 Reference Manual ....................................................................... Error! Bookmark not defined.

7.1 Wi-Fi> Basic ............................................................................................................................................................... 80

7.2 Wi-Fi> Advanced ........................................................................................................................................................ 81

7.3 Wi-Fi>WPS ................................................................................................................................................................ 83

Issue 01 (2015-07-10) Huawei Proprietary and Confidential

About this Guide

About This Chapter

This document provides information and procedures on the installation and configuration of

LTE Outdoor CPE. You could utilize the information in this guide to set up your device.

1.1 Prerequisite Skills and Knowledge

1.2 Conventions Used in this Document

1.1 Prerequisite Skills and Knowledge

To use this document effectively, you should have a working knowledge of Local Area

Networking (LAN) concepts and wireless Internet access infrastructures. In addition, you should be familiar with the following:



Hardware installers should have a working knowledge of basic electronics and mechanical assembly, and should understand related local building codes.

Network administrators should have a solid understanding of software installation procedures for network operating system and troubleshooting knowledge. LTE Outdoor

CPE has a web GUI which supports http/https protocol; it could be used to configure the

CPE settings through the web browser by user"s PC. Please refer to the following pages for more detail.

1.2 Conventions Used in this Document

The following typographic conventions and symbols are used throughout this document:

Very important information. Failure to observe this may result in damage.

Important information that should be observed.

Additional information that may be helpful but not required.

Issue 01 (2015-07-10) Huawei Proprietary and Confidential

bold

Menu commands, buttons and input fields are displayed in bold

Issue 01 (2015-07-10) Huawei Proprietary and Confidential

Introduction

About This Chapter

2.1 Product Overview

2.2 Product Package

2.3 Connectors

2.4 LED Indicators

2.5 Installation

2.1 Product Overview

LTE Outdoor CPE is an all-in-one device that integrates TD-LTE



Support TD-LTE

Support 3GPP Release 10 compliant

Support 1TX/2RX with TX switched diversity (LTE)

Support LTE UE Category 4

Support 2 LAN ports and 1 VoIP port

Support HTTP/HTTPs Web GUI

2.2 Product Package

Item

LTE ODU CPE

PoE Box

User Manual

Power Adapter

Plug

Q'ty

Issue 01 (2015-07-10) Huawei Proprietary and Confidential

Item

Mount Kit

Ground Cable

Q'ty

If any item of mentioned above is missing or damaged, please contact our customer support immediately.

2.3 Connectors

The Outdoor LTE CPE has following connectors (from left to right):

1. One SIM card slot for inserting SIM card..

2. One RJ-45 connector for connecting to the IDU WAN port.

3. LED indicator inside.

4. A grounding screw on the rear panel.

IDU Rear Panel

IDU Front Panel

Issue 01 (2015-07-10) Huawei Proprietary and Confidential

2.4 LED Indicators

ODU LED Indicators as following:.

LED name

LED list

Location

Main Power

Ethernet Status

SIM status

Color LED Behavior

- -

Blue

Blinking

OFF

Yellow Steady ON

Blinking

OFF

Green

Steady ON

Blinking when On-hook

OFF

Status Indication

Power On

Factory Reset

Power Off

Ethernet connected

Upgrading

No Ethernet action

SIM Detected

PUK / PIN Code

No SIM Detected

Issue 01 (2015-07-10) Huawei Proprietary and Confidential

LED name Location

4G Status LED : Link Status

4G-Signal

4G-1

Color LED Behavior

Blue

Status Indication

When CPE is power on, each LED indicates each link status

Chasing light

Blinking

Steady ON

Searching

Network Entry

SINR < 0dB

4G-2 Blue Steady ON

4G-3 Blue Steady ON

4G-4 Blue

Steady ON

4G-5 Blue

Steady ON

2 System

IDU LED Indicators as following:

Number LED name

1 Main Power

Color LED Behavior

Green

Off

Green

Blinking

Off

LTE Signal

Strength

LAN 1 & 2

WLAN_2G

WLAN_5G

Phone (VoIP)

Green

Off

Blinking

Off

Blinking

Off

Blinking

Off

Blinking

Off

0dB ≦ SINR < 4dB

4dB ≦ SINR < 9dB

9dB ≦ SINR < 16dB

16dB ≦ SINR

Status Indication

Power On

Power Off

System is booting

System is upgrading

System is disabled

Display signal Strength

1 LED: SINR< 0dB

2 LEDs: 0dB <=SINR< 4dB

3 LEDs: 4dB <=SINR< 9dB

4 LEDs: 9dB <=SINR< 16dB

5 LEDs: 16dB <=SINR

No signal

Ethernet connected

No Ethernet connected

Enable 2.4G WiFi

Data transmition

Disable 2.4G WiFi

Enable 5G WiFi

Data transmition

Disable 5G WiFi

Registered

Busy

De-registered

Issue 01 (2015-07-10) Huawei Proprietary and Confidential

2.5 Installation

Before installing the LTE outdoor CPE, verify that you have all the items listed in the package checklist. If any of the items is missing or damaged, contact your service provider.

Only experienced installation professionals who are familiar with local building and safety codes and, where applicable, are licensed by the appropriate government regulatory authorities should install outdoor units and antennas.

2.5.1 Installing LTE Outdoor CPE

Any of the items are missing or damaged, contact your LTE service provider.

Step 1: Selecting a Location

The ODU should be pole-mounted outdoors and aligned so its antenna faces the nearest LTE base station. When selecting a suitable location for the unit, consider these guidelines:

1. Place the ODU as high as possible to achieve the best possible link quality.

2. Place the ODU away from power and telephone lines.

3. Avoid placing the ODU too close to any metallic reflective surfaces.

4. Be sure to ground the ODU with an appropriate grounding wire by attaching it to the grounding screw on the unit and to a good ground connection.

Step 2: Before Mounting the Device

Make sure the ODU is turned off and NO PoE supply connected before you insert SIM card or it may damage your SIM card.

Please check below items before installing the outdoor device.

LED indicator inside and SIM card slot for inserting SIM card.

One RJ-45 connector for connecting to the ODU to IDU

Insert power plug to the power adapter and then plug in power adapter to DC 56V port of

IDU.

Make sure the grounding screw on the rear panel.

Must connect a Grounding cable between the ground terminal of the ODU (marked ) and a ground connection. (Suggest to with Ethernet lighting protector between Ethernet cable and indoor PoE supplier for better lighting and surge protection).

For additional lightning protection, it is recommended to use a lightning arrestor immediately before the Ethernet cable enters the building.

Issue 01 (2015-07-10)

To connect with Grounding cable

Huawei Proprietary and Confidential

Step 3: Connect the cable with waterproof node

1. Remove the sealing gland plug from the gland nut.

2. Open the sealing gland nut and remove it. Do not disassemble the gland base from the bracket.

3. Insert the cable into the sealing gland base and connect it to the RJ-45 connector at the bottom of the ODU, labeled. Make sure that the connector is completely inserted and tightened.

4. Insert the rubber bushing on the cable into the gland base.

5. Gently twist the body into the ODU.

Step 4: Mounting the Device: Installing Pole Mount

1. Lossen the locking mechanism of mental strap by hand or screwdriver. (a)

2. Wrap the metal strap with Pole-Mount Bracket. (a and b)

3. Attach the Pole-Mount bracket to the other side of the pole. (a, b, and d)

4. Tighten the locking mechanism of mental strap by screwdriver. (d)

5. Thread the M8*23mm bolts through a spring washer, flat washer and ODU. Tighten the nuts. (e and f)

Issue 01 (2015-07-10) Huawei Proprietary and Confidential

2.5.2 Connecting the Cable

Step 1: Physical connection as following

1. Insert a USIM in ODU (SIM card slot).

2. Connect the Ethernet cable to the RJ45 ports of IDU and ODU.

Connect the Ethernet cable from the computer to one of the IDU’s Ethernet Ports

4. Connect the supplied power adapter to the IDU. The PWR LED shines a steady green when device ready.

5. Mounting the Device.

Step 2: Installing Pole Mount

1. Lossen the locking mechanism of mental strap by hand or screwdriver. (a)

2. Wrap the metal strap with Pole-Mount Bracket. (a and b)

3. Attach the Pole-Mount bracket to the other side of the pole. (a, b, and d)

4. Tighten the locking mechanism of mental strap by screwdriver. (d)

5. Thread the M8*23mm bolts through a spring washer, flat washer and ODU. Tighten the nuts. (e and f)

Step 3: Connect to the Internet

Physical connection is as following (Refer to Installing Device Instruction).

1. Insert a USIM in ODU(SIM CARD SLOT).

2. Connect IDU(WAN) and ODU(RJ45) via Ethernet cable.

3. Use power adapter to connect IDU(Power)

4. Connect IDU(ETHERNET PORTS) and PC via Ethernet cable.

5. PC will get default IP 192.168.1.xxx (xxx: 2-254). Open a web browser and go to https://192.168.1.1.

Issue 01 (2015-07-10) Huawei Proprietary and Confidential

Use ONLY the PoE Box which supplied with the ODU. Otherwise, LTE

Outdoor CPE may be damaged.

Issue 01 (2015-07-10) Huawei Proprietary and Confidential

Web Interface

About This Chapter

3.1 Login to Web-GUI

3.2 Function Button

3.3 Status and device information

3.4 Menu Structure

3.1 Login to Web-GUI

Step 1:

Open the Web browser and enter the default IP address of the device, which is:

http://192.168.1.1/

Step 2:

Enter the user login credentials to access web management interface.

Default Log-in information:

Username: user

Password: ●●●●●●

Log-in protection:

If you key-in the log-in username or password error more than three times, the device would request addition Identify Code to protect any illegal Hacker attack.

You can press re-fresh button to re-fresh the identify code if it is hard to read.

Issue 01 (2015-07-10) Huawei Proprietary and Confidential

NOTE

We recommend you to change the default Wi-Fi password while the first time log-in, please go Management>Setup Wizard or Management>Wi-Fi setup to change the Wi-Fi password.

Issue 01 (2015-07-10) Huawei Proprietary and Confidential

3.2 Function Button

(Disconnect)

(Reconnect)

Function button is located at each Web UI page Top-Right corner.

REBOOT

Force device to initial a reboot.

LOGOUT

Quickly log out the device, device will back to log-in page

RECONNECT/DISCONNECT

Let the LTE device reconnect or disconnect to WAN.

This reconnect and disconnect is related to connection mode configuration, you can go

Management>

Modem Setup>Connection Mode

to set up.

Issue 01 (2015-07-10) Huawei Proprietary and Confidential

NOTE

If device is on the Auto connection mode, it will display RECONNECT icon

If device is on the Manual connection mode; when the device is connected it will display DISCONNECT icon for you to manual disconnect it; when the device is disconnect it will display RECONNECT icon

Issue 01 (2015-07-10) Huawei Proprietary and Confidential

3.3 Status and device information

3.3.1 Status> Device Status

This page is information only, here displays the current status of the device such as system uptime and WAN information.

You can refer to below column for detail definitions.

Operation Mode

The mode to forward data packets between Internets. There are three options: Gateway/VPN-L2TP(Tunnel Layer 2 or Layer 3)/Router

Please go

Management>WAN Setup

to configure it.

IP Connection

– Single mode

(On/Off) value is depends on if the WAN connection is available or not.

Data/VoIP IP Connection

– Dual mode

(On/Off) value is depends on if the Data or VoIP connection is available or not.

VPN Status

– Layer2

It shows the Layer2 VPN connection status, Connected: VPN is connected/ N/A: VPN is not connected yet.

VPN IP Address

– Layer3

It shows the Layer3 VPN connection status, when connected it will display the VPN client IP address; N/A: VPN is not connected yet.

Connection Mode

The mode to obtain IP address. Available options: DHCP/ Static.

IP Address

– Single mode

For DHCP mode - IP address acquired on the WAN interface is displayed.

Otherwise it is N/A

Data/VoIP IP Address

– Dual mode

For DHCP mode - IP address acquired on the Data/VoIP WAN interface is displayed. Otherwise it is N/A

Issue 01 (2015-07-10) Huawei Proprietary and Confidential

2.4GHz WiFi

DNS Server

The Domain Name Server address, if there is any

5GHz WiFi

Time Server

The NTP (Network Time Protocol) server address.

Firewall

Here displayed your current firewall level; there are three default configurations for you to select: Low/Medium/High or you can select

Custom to configure by your preference. For more detail please refer to

Basic> Firewall

section.

DMZ

DMZ enabled or disabled.

UPnP

UPnP enabled or disabled.

DDNS

DDNS enabled or disabled.

Device Up Time

The duration since the unit is powered on in format "x day(s)

<hour>:<minute>:<second>".

Device Restart Reason

The reason for last device reboot (e.g. Software Upgrade).

− Click the "Refresh" button manual update the current status.

− Click the "Auto" button auto update the current status.

Issue 01 (2015-07-10) Huawei Proprietary and Confidential

3.3.2 Status> Modem Status

The Modem Status displays a summary of the LTE network connection parameters .The information includes:

Network

Current active network mode i.e. LTE

Connection Status

The status of modem connection.

Connection Time

Time during which the unit is connected to the eNB or base station.

Roaming Status

Informs current roaming status.

PLMN

Public Land Mobile Network identity.

Issue 01 (2015-07-10) Huawei Proprietary and Confidential

Operator Name

Current connected operator name.

IMSI

International Mobile Subscriber Identity.

USIM Status

SIM card status information.

PIN Retries

The remained PIN retry count.

PUK Retries

The remained PUK retry count.

Uplink current speed

Uplink data rate.

Downlink current speed

Downlink data rate.

Uplink/Downlink Traffic

Displays the current accumulate Downlink/Uplink traffic. You can reset by press the

”Clear

Traffic” button in right.

SINR

Signal to Interference plus Noise Ratio (dB).

RSSI

Received Signal Strength Indication 1dBm unit. Minimum: -141.

RSRQ

Reference Signal Received Quality 0.5dBm unit. Minimum: -40.

RSRP

Reference Signal Received Power 1dBm unit. Minimum: -141.

PCI

Issue 01 (2015-07-10) Huawei Proprietary and Confidential

Pre-coding Control Indication

CQI

Channel Quality Indication

APN Status

– Single mode

Displayed the connect status(Success /Fail / N/A) of Single APN , you can go

Management>Modem Setup to setup the Single APN

Data / VoIP APN Status

– Dual mode

Displayed the connect status (Success /Fail / N/A) of Dual APN , you can go

Management>Modem Setup to setup the Dual APN.

Current Band

Current connected Band(According to 3GPP defined)

− Click the "Refresh" button manual update the current status.

− Click the "Auto" button auto update the current status.

Issue 01 (2015-07-10) Huawei Proprietary and Confidential

3.3.3 Status> Telephony Status

SIP User IP Address

IP address of the Session Initiation Protocol (SIP), an application-layer control protocol that can establish, modify, and terminate multimedia sessions such as Internet telephony calls (VOIP).

Status

Registered or De-registered in the SIP server. This information also can be observing on the front panel voice line LED.

Account

The SIP Account. The account format depends on the SIP Server.

Call Waiting

Allow the second caller to wait on-line while an existing phone call is on-going.

If you want switch the call please press “flash” key on your telephone.

You can go

Management>Telephony

to change the setting Disable/Enable.

3.3.4 Status> About

This page displays the device default necessary information. Those values are set by the manufacturer as the factory defaults.

Service Provider

Product Name

IMEI

2.4GHz

5 GHz Wi-Fi MAC

Model ID

Hardware Version

Your network and service operator.

Product type.

International Mobile Equipment Identity number.

2.4GHz Wi-Fi MAC address.

5GHz Wi-Fi MAC address.

Device model name.

Device HW version.

Issue 01 (2015-07-10) Huawei Proprietary and Confidential

Software Version

Device SW/FW version.

Indoor device’s serial number.

Indoor Unit Serial

Number

Outdoor Unit Serial

Number

Outdoor device’s serial number.

Chip Version

Device Chip version.

3.3.5 Status> Help

While you press the Help you will be direct to download a .pdf to guide you how to operate this device in detail.

3.4 Menu Structure

After entering "Detailed Configuration Page", the user can quickly jump to the specified Sub Menu. (By clicking

"Quick Panel" at the bottom of the page.)

Users can refer to the menu structure given below:

Status

Device Status

Modem Status

Telephony Status

Management

About

Help

Setup Wizard

Modem Setup

WAN Setup

LAN Setup

IPv6

Telephony

Diagnostics

System Log

Issue 01 (2015-07-10) Huawei Proprietary and Confidential

Personalization

Basic

Advanced

WiFi

PIN Management

Configuration

Device Setup

Software

Firewall

DMZ

UPnP

Dynamic DNS

VPN Passthrough

MAC Filtering

IP Filtering

Port Forwarding

Port Trigger

Layer 7

URL Filtering

ACL Filtering

Static Routing

Basic

Advanced

WPS

Issue 01 (2015-07-10) Huawei Proprietary and Confidential

Reference Manual

About This Chapter

4.1 Management

4.1.1 Management >Setup Wizard

The Setup Wizard will guide you to do the important setting of the device.

− Step 1: By press the “Next” button to start Wizard, we will guide you to set up your Time zone.

− Step 2: 1. Selection your locate country, NTP server and location time zone, and check if your location have daylight saving.

2. Review all your settings, if no problem, please press

“Next”.

− Step 3: Set up your 2.4GHz and 5GHz Wi-Fi network name/Encryption and Wi-Fi Password, then press “Next”.

− Step 4: Check your settings and again then press “Save” button to apply the change.

− Click the "Next" button to launch the Setup Wizard.

− Click the "Previous" button to go back to the previous page

− Click the "Cancel" button to return to the first page.

− Click the "Save" button to save any modified settings.

Issue 01 (2015-07-10) Huawei Proprietary and Confidential

4.1.2 Management>Modem Setup

In this page, you can configure all the network related parameters.



Connection Mode:

Set connection as Auto or Manual.

 Auto Mode: Device will continuously try to connect network automatically.

 Manual Mode: You have to manual press the Reconnect button to re-connect to network every time, if you failed to connect to network.



APN Setting

Setting how APN (Access Point Name) is assigned.

 APN mode: Single/ Dual

You can configure your APN as single or dual, only when you select the dual APN, the second APN (VoIP APN) will be editable.

 Data APN

 APN Setting:

Auto - Device will automatically choose the default APN setting

Manual

–Manually enter the Data APN of your network, which your service provider gave you

 User Name: Key-in the user name for the APN if there is any, this information should provide by your service provider.

 Password: Key-in the password for the APN if there is any, this information should provide by your service provider.

 VoIP APN

 APN Setting:

Auto - Device will automatically choose the default APN setting

Manual

–Manually enter the VoIP APN of your network, which your service provider gave you

 User Name: Key-in the user name for the APN if there is any, this information should provide by your service provider.

 Password: Key-in the password for the APN if there is any, this information should provide by your service provider.

 Roaming Setting

Enable/Disable roaming to other network operator.



Enable - Roaming to other network operator is enabled.



Disable - Roaming to other network operator is disabled.

Issue 01 (2015-07-10) Huawei Proprietary and Confidential

- Click Undo to clear the changes that you have made to this window.

- Click Apply to activate your changes

Single mode

Issue 01 (2015-07-10)

Dual Mode

Huawei Proprietary and Confidential

4.1.3 Management>WAN Setup

 Operation Mode

It displays the mode how to forward data packets between Internet and Intranet.

 Gateway Mode:

The mode to obtain IP address for the device, in the gateway mode the SNAT is enabled.

− MTU Size:

 Enter the value for transmission unit size (Range: 576-1500).

 VPN Mode:

Set the WAN maximum transmission unit (MTU) size in bytes.

VPN Type:

You can select your VPN type, this device support L2TP and GRE

− L2TP



BCP: Enable: You can perform theL2 VPN connection.



Internet IP Address: The VPN server IP address that you want to connect to.



Username: The user name of your VPN account



Password: The password of your VPN account



Host Name: If server requests the item, need to fill in



MTU Size: Enter the value for transmission unit size (Range: 576-1500).

NOTE

If you select the Layer 3 VPN, you need go

Advance->Static Routing to add the routing rule of the VPN section.



BCP: Disable: You can perform the L3 VPN connection



NAT Support:



Enable: Enable to let the inner source IP to do the NAT



Disable: Disable to let the inner source IP bypass the NAT



Internet IP Address: The VPN IP address server that you want to connected to.



Username: The user name of your VPN account



Password: The password of your VPN account



Host Name: If server requests the item, need to fill in



MTU Size: Enter the value for transmission unit size (Range: 576-1500).

− GRE



GRE Type: Layer 2



Tunnel Destination IP: Please input VPN tunnel

’s Destination IP

address



MTU Size: Enter the value for transmission unit size (Range: 576-1500).



GRE Type: Layer 3



NAT Support:



Enable: Enable to let the inner source IP to do the NAT



Disable: Disable to let the inner source IP bypass the NAT



Tunnel Interface IP: Please input the VPN tunnel

’s IP address



Tunnel Interface Mask: Please input the VPN tunnel

’s IP subnet mask



Tunnel Destination IP: Please input VPN tunnel

’s Destination IP address



MTU Size: Enter the value for transmission unit size (Range: 576-1500).

Issue 01 (2015-07-10) Huawei Proprietary and Confidential

 Router Mode:

When device is set as router mode: the SNAT (source NAT) will be disabled, sothatfirewall function

(i.e. DMZ, port forwarding) will not applicable.

− MTU Size:

Sets the WAN maximum transmission unit (MTU) size in bytes.

 Enter the value for transmission unit size (Range: 576-1500).

- Click Undo to clear the changes that you have made to this window.

- Click Apply to activate your changes

Issue 01 (2015-07-10) Huawei Proprietary and Confidential

4.1.4 Management>LAN Setup

In this page, you can change the Web UI and device local IP address distribution range.

−

LAN IP Address: Please input the LAN IP address here, the default value is 192.168.1.1

−

DHCP Service Type: Please select the DHCP service type ,options are :Disable, Server, Relay

 Disable: The device will not assign LAN IP address to PC; you have to manually set static IP address to the connected PC to access the UI.

 DHCP Server:

The unit has a built-in DHCP server that can be used for managing the distribution of

IP addresses for the devices connected to the local LAN port (Ethernet or Wi-Fi) and

Web UI. In the DHCP Server page you set DHCP parameters for dynamic IP assignment.

Enable DHCP Server

Select this check-box dynamically assigns a leased IP address to clients that connect to the device from the local network.

If you select Disable, you need to manually configure the IP addresses of the computers and other

LAN devices.

DHCP Server IP Address

Enter a DHCP server IP address.

DHCP Starting IP Address

Enter the first IP address assigned by the DHCP server.

DHCP Ending IP Address

Enter the last IP address assigned by the DHCP server.

DHCP Lease Time

Set the time, how long you want to renew the IP.

−

DHCP Lease Reservation

The Lease Reservation page displays information on reserved IP addresses for leasing. In this page you assign the specific IP addresses to the specific client device connected to the Ethernet ports and Wi-Fi access point. You can also add, delete, or modify the reservation settings.

Select

Select an IP to delete.

Host Name

Enter a name to the host.

MAC Address

Add a device MAC address.

IP Address

Issue 01 (2015-07-10) Huawei Proprietary and Confidential

Specify a reservation IP address for a specified MAC address.

Enabled

Select if to enable or disable a specified IP setting.

−

DHCP Lease Status

The Lease Status page displays information regarding the leased IP address(es):

Client Host Name

MAC Address

This is display the connected PC name which connected to the

LTE device.

This is display the connected PC MAC address which connected to the LTE device.

IP Address

This is display the IP address that assigned to this LAN device(Host

PC)

This display how many seconds remain for this assigned IP,

Remaining Lease

Duration

Action

Block: To Block the specific PC, after press the

“Block” button the LAN device cannot access this LTE device any more.

Unblock: Press

“Unblock” button to allow the LAN device to back to connect again.

This function is for you to easily manage the LAN devices, to avoid the unexpected device access from your LAN.

Status

This shows the current IP assignment availability.

 DHCP Relay:

DHCP Relay Agent

 DHCP Relay Server IP Address: The device will request IP address from the DHCP

Relay server, please input the DHCP relay Server

’s IP address for obtain the IP address.

If you input wrong DHCP Relay server IP address or Relay server is not working, please manually set static IP address to the connected PC to access the UI.

- Use the Add or Delete buttons to add or clear reserved IPs for leasing, please click Apply button to confirm the Add or Del.

- Click Undo to clear the changes that you have made to this window.

Issue 01 (2015-07-10) Huawei Proprietary and Confidential

- Click Apply to activate your changes.

Issue 01 (2015-07-10) Huawei Proprietary and Confidential

4.1.5 Management>IPv6

Enable IPv6

This is a check box, please checked to enable the IPv6address or un-check to disable it.

WAN Setting:

−

IPv6 Type:

You can assign the how to get IPv6 address here, there are two options: static/auto configuration.

 Auto configuration: The device will get IPv6 address automatically.

Enable DHCP-PD:

Checked the checkbox to enable the DHCP-PD server to allow the server assign the prefix the client

DNS: You can define the DNS as Auto or Manual

DNS1:

Please input the IPv6 DNS server

DNS2:

Please input the IPv6 DNS server if there is any.

LAN Setting:

Auto-configuration type:

Disable, SLAAC DHCPv6, SLAAC RDNSS, Stateful DHCPv6

 Disable:

Disable the IPv6 address assignment for LAN client.

 SLAAC DHCPv6:

(Stateless Address Auto-configuration DHCPv6), Router

Advertisement (RA) will contain the IPv6 Prefix and default gateway information and

DHCP v6 will provide DNS address and other network information. This method of

LAN IP assignment will recommend to use at private area due to it is with lower security level.

-

IPv6 SLAAC DHCPv6 RA Lifetime(seconds):

The IP address will reset after X seconds, default is set as: 3600 sec

Issue 01 (2015-07-10) Huawei Proprietary and Confidential



SLAAC RDNSS:

(Stateless Address Auto-configuration +Recursive DNS

Server),Router Advertisement (RA) will regularly broadcast the multicast package and the Client will get Prefix, default gateway and DNS information, the Client will combine the Prefix and auto-generate the Host ID as the device’s IPv6 address.

-IPv6 SLAAC RDNSS RA Lifetime(seconds):

The IP address will reset after X seconds, default is set as:3600sec



Stateful DHCPv6:

RA only contain the default gateway information, the other information like IPv6 Prefix ,Host ID and DNS IP address is assigned by DHCPv6;

DHCPv6 will record all the LAN IPv6 address, MAC list and regularly maintain the

IPv6 address record. If you are in the public area, we will recommend using stateful

DHCv6.

-IPv6 Address Pool Start:

Defined the IPv6 address start point, default is: 1

-IPv6 Address Pool End:

Defined the IPv6 address end point, default is: 200

-IPv6 Address Lifetime(seconds):

The IP address will reset after X seconds, default is set as:

3600 sec

- Click Undo to clear the changes that you have made to this window.

- Click Apply to activate your changes.

Issue 01 (2015-07-10) Huawei Proprietary and Confidential

4.1.6 Management> Telephony

This chapter describes how to configure VoIP parameters.

Voice over Internet Protocol (VoIP) technology is a way of using the Internet to make phone calls. You can make VoIP calls by connecting a regular phone to the unit's Phone ports.

Before using the VoIP Phone ports on the unit, you must have an account with a SIP service provider. To change the settings below, please always double confirm your service provider.

Attention

VoIP doesn

’t support “flash + number” feature.

Enable VoIP

This is a check box, please checked to enable the VoIP function or un-check to disable VoIP.

− Account

 User account

Username

Password

The SIP (Session Initiation Protocol) User name. Its format depends on the SIP Server.

The SIP user Password.

Password Confirm

Enter the SIP user Password again.

User Account

The SIP Account. Its format depends on the SIP Server.

Display Name

Enter the name that will be displayed as your ID/number, for the outgoing call the receiver will see your Display name as Caller ID (if supported by the SIP server).

 Server account

Enable STUN

(Session Traversal Utilities for NAT)STUN is a standardized, light-weight protocol that allows an application to discover the presence and types of NATs and firewalls between itself and the public Internet.

It also enables the application to determine the public IP addresses allocated to it by the NAT.

IP address or domain name of the STUN Server.

STUN Server

Address

User Domain

This LTEDevice’s domain name.

Registrar Address

SIP server IP address

Registrar Port

Port number of the SIP Server.

Outbound Proxy

Address

A SIP Outbound Proxy acts, like any proxy server. Listening on an unblocked port number and forwarding requests between SIP client and your VoIP provider, it helps bypassing the restrictions imposed by your

Internet provider.

Issue 01 (2015-07-10) Huawei Proprietary and Confidential

If both an Outbound Proxy and a Registrar are configured, the Register message is sent to the Outbound Proxy, which forwards it to the

Registrar.

The number of the Port on which the outbound Proxy listens.

Outbound Proxy

Port

RTP Port Range

Start

RTP Port Range

End

Enter the listening start port number(s) for RTP traffic, if your VoIP service provider gave you this information. Otherwise, keep the default values.

Enter the listening end port number(s) for RTP traffic, if your VoIP service provider gave you this information. Otherwise, keep the default values.

IF you only have one port for listening RTP, please insert the same number in Start/End field.

 Call Feature Settings



Call Waiting

Enables or Disable the second caller can wait on line while you are on the call, you can press the flash key on the telephone to switch the call.



Call Waiting TimeOut

Enter a number of seconds after which the call waiting is timed out.



Call Hold

Enables or Disable the Call Hold function

The Call Hold function is allow you to hold current call by press the flash key on the telephone



Dial Plan

A dial plan is a set of rules used for determining whether a complete set of numbers has been entered for the IP address of SIP server.

The device support two dial plans:

✽ xx : “✽”represent the asterisk key on the phone;” x “represent any number (0~9).This dial plan is for the speed dial

“|” represent or, you can set several dial plan but separate them by |. xx.T : ” x” represent any number(0~9) ; “.” means arbitrary number of digits ; T is just a symbol me ans end number. You didn’t need to key-in anything to end the dial, just wait dial time out (3sec), if you don’t want to wait for 3sec, just set the dial plan as: xx.#. For example, you could dial 1111#, and the phone number 1111 would be dialed immediately.



Max Flash Time

Set the max Flash key press time, if you press the Flash key over x seconds define in the column, the action will be ignored. (Please enter 0.2 ~ 1.5 seconds.



Ring Tone TimeOut

Set how long you want the ring tone exist. (Please enter 15 ~ 60 seconds)



Delay Time After On Hook

Set a really hang up delay time. When you hang up the call for x seconds the call will be really dropped. (Please enter 0 ~ 5 seconds),



Ring Back Tone

You can determine the ring tone sound here



Frequency Quota:

Issue 01 (2015-07-10) Huawei Proprietary and Confidential

You can set the ring tone frequency here, the value should between 300~800 Hz.

The device supports to set 1 or 2 frequency.



Ring Back Tone On:

Set ring back tone continues for how long in a ring tone cycle, please enter 0~4 seconds or asterisk (*) to set continue on)



Ring Back Tone Off

Set ring back tone off for how long-in a ring tone cycle, please enter 0~4 seconds or asterisk (*) to set always off)



Call Waiting Tone

You can determine the call waiting tone sound here



Frequency Quota:

You can set the call waiting tone frequency here, the value should between

300~800 Hz.The device supports to set 1 or 2 frequency.



Ring Back Tone On:

Set ring back tone continues for how long in a ring tone cycle, please enter 0~4 seconds or asterisk (*) to set continue on)



Ring Back Tone Off

Set ring back tone off for how long in a ring tone cycle, please enter 0~4 seconds or asterisk (*) to set always off)



Dial Tone

You can determine the dial tone sound here



Frequency Quota:

You can set the dial tone frequency here, the value should between 300~800 Hz.

The device supports to set 1 or 2 frequency.



Ring Back Tone On:

Set ring back tone continues for how long in a ring tone cycle, please enter 0~4 seconds or asterisk (*) to set continue on)



Ring Back Tone Off

Set ring back tone off for how long in a ring tone cycle, please enter 0~4 seconds or asterisk (*) to set always off)



Busy Tone

You can determine the busy tone sound here



Frequency Quota:

You can set the busy tone frequency here, the value should between 300~800 Hz.

The device supports to set 1 or 2 frequency.



Ring Back Tone On:

Set ring back tone continues for how long in a ring tone cycle, please enter 0~4 seconds or asterisk (*) to set continue on)



Ring Back Tone Off

Set ring back tone off for how long in a ring tone cycle, please enter 0~4 seconds or asterisk (*) to set always off)



Speed dial

Please pre-set the mapping table for speed dial, you can have maximum speed dials.

- Dial Number: Please define the speed dial number, this column is only allow to key-in: numbers

0~9

- Real Number: Please correctly fill-in the real dial number here, this column is only allow to key-in: numbers 0~9,#,*

Issue 01 (2015-07-10) Huawei Proprietary and Confidential

Call Feature

Caller ID

Call Hold

Call Waiting

Cancel Call

Waiting

Caller Name

Max Flash Time

Procedure (Example)

1. Pick up Phone-1. Dial tone should be presented

2. Dial the number of Phone-2. Phone-2 should ring and Phone-1 should present ring back tone.

3. The caller ID(phone number) of Phone-1 should be displayed in the screen of Phone-2.

1. Configure the display Name of Phone-1 on web UI.

2. Pick up Phone-1. Dial tone should be presented.

3. Dial the number of Phone-2. Phone-2 should ring and Phone-1 should present ring back tone.

4. The caller Name (display Name) of Phone-1 should be displayed in the screen of Phone-2.

1. Enable the Call Hold on web UI.

2. Pick up Phone-2. Dial tone should be present.

3. Dial the number of Phone-1. Phone-1 should ring and Phone-2 should present ring back tone.

4. Pick up Phone-1. Ring back tone should be stopped in Phone-2 and bi-directional voice traffic should flow.

5. Press Flash button on Phone-2.

6. Phone-1 should be held. If Phone-2 presses the Flash button again, the call should be retrieved (i.e. Phone-1 is taken off hold)

1. Make sure the Call Hold is enabled.

2. Enable the Call Waiting on web UI.

3. Pick up Phone-1. Dial tone should be presented.

4. Dial the number of Phone-2. Phone-2 should ring and Phone-1 should present ring back tone.

5. Pick up Phone-2. Ring back tone should be stopped in Phone-1 and bi-directional voice traffic should flow.

6. Pick up Phone-3. Dial tone should be presented in Phone-3.

7. Dial the number of Phone-2 from the Phone-3.

8. Phone-2 presents the call waiting tone. Verify that the Phone-3 presents the ring back tone.

Attention.

1. When Phone-2 press Flash button, Call should be established between Phone-2 and Phone-3.

2. Phone-2 could use the Flash button to switch to the other call

1. Disable the call waiting on web UI.

2. Pick up Phone-1. Dial tone should be presented.

3. Dial the number of Phone-2. Phone-2 should ring and Phone-1 should present ring back tone.

4. Pick up Phone-2. Ring back tone should be stopped in Phone-1 and bi-directional voice traffic should flow.

5. Pick up Phone-3. Dial tone should be presented in Phone-3.

6. Dial the number of Phone-2 from the Phone-3.

7. Phone-3 presents the busy tone and there is no disturbances between phones-1 and Phone-2.

1. Set Max Flash Time to 0.9s on Phone-1 UI.

Issue 01 (2015-07-10) Huawei Proprietary and Confidential

Three Way

Conference Call

2. Pick up Phone-1. Dial tone should be presented.

3. Dial the number of Phone-2. Phone2 should ring and Phone-1 should present ring back tone.

4. Pick up Phone-2. Ring back tone should be stopped in Phone-1 and bi-directional voice traffic should flow.

5. Press Flash button on Phone-1

6. Press Flash button on Phone-1 and 0.9 second later, Phone-2 presents the hold tone.

Ring Tone TimeOut

1. Set Ring Tone TimeOut to 30s on Phone-1 UI.

2. Pick up Phone-1. Dial tone should be presented.

3. Dial the number of Phone-2. Phone2 should ring and Phone-1 should present ring back tone.

Don’t pick up Phone-2, Phone-1 will presents the busy tone after 30 seconds.

Delay Time After

On Hook

1. Set Delay Time After On Hook to 1s on Phone-1 UI

2. Pick up Phone-1. Dial tone should be presented.

3. Dial the number of Phone-2. Phone2 should ring and Phone-1 should present ring back tone.

4. Pick up Phone-2. Ring back tone should be stopped in Phone-1 and bi-directional voice traffic should flow.

5. On hook the Phone-1, Phone-2 presents the busy tone after 1 second.

1. Make sure the Call Hold is enabled.

2. Make a phone call from Phone-1 to Phone-2 and make sure the call is established between Phone-1 and Phone-2.

3. Phone-2 presses the Flash button and make a phone call to Phone-3 and make sure the call is established between Phone-2 and Phone-3.

4. Phone-2 presses the Flash button and all three phones will be in conference call.

5. After all three phones in the conference call. Each phone should be able to hear the speech of other phones.

Attention:

If we hang up the Phone-1 or Phone-3, another call (Phone-2 with

Phone-3 or Phone-2 with Phone-1) should still exist.

If we hang up the Phone-2, the all call should be disconnected.

Blind Call Transfer

1. Make sure the Call Hold is enabled.

2. Pick up Phone-1. Dial Tone should be presented.

3. Dial the number of Phone-2. Phone-2 should ring and Phone-1 should present ring back tone.

4. Pick up Phone-2. Ring back tone should be stopped in Phone-1 and two-way voice should be presented.

5. Phone-2 press the Flash button followed by the number of Phone-3.

6. Phone-3 should start ringing and Phone-2 hang up. Pick up Phone-3.

7. There should be a call setup between Phone-1 and Phone-3 with voice pass through.

Attended Call

Transfer

1. Make sure the Call Hold is enabled.

2. Pick up Phone-1. Dial tone should be presented.

3. Dial the number of Phone-2. Phone-2 should ring and Phone-1 should present ring back tone.

Issue 01 (2015-07-10) Huawei Proprietary and Confidential

Dial Plan

Ring Back Tone

Call Waiting Tone

Dial Tone

4. Pick up Phone-2. Ring back should be stopped in Phone-1 and two-way voice should be established.

5. Phone-2 press the Flash button followed by the number of Phone-3.

6. Phone-3 should start ringing and pick up Phone-3. The call is established between Phone-2 and Phone-3

7. Hang up the Phone-2

8. There should be a call setup between Phone-1 and Phone-3.

Every phone number need to follow dial plan’s rule. (page.54)

Example1. <*xx>: *12, *73, *99…

Example2. <xx.T>: 12, 999, 9900, 88888…

1. Set a rule on Phone-1 UI.

2. Pick up Phone-1. Dial tone should be presented.

3. Dial the number of Phone-2. Phone-2 should ring.

4. Phone-1 should present ring back tone, and the tone is depend on your settings.

1. Set a rule on Phone-1 UI.

2. Pick up Phone-1. Dial tone should be presented.

3. Dial the number of Phone-2. Phone-2 should ring and Phone-1 should present ring back tone.

4. Pick up Phone-2. Ring back tone should be stopped in Phone-1 and bi-directional voice traffic should flow.

5. Pick up Phone-3. Dial tone should be presented in Phone-3.

6. Dial the number of Phone-2 from the Phone-3.

7. You can hear Call Waiting Tone from Phone-1, and the tone is depend on your settings.

1. Set a rule on Phone-1 UI.

2. Pick up Phone-1. Dial tone should be presented, the tone is depend on your settings.

Busy Tone

1. Set a rule on Phone-1 UI.

2. Pick up Phone-2.

3. Pick up Phone-1. Dial tone should be presented.

4. Dial the number of Phone-2. Phone-2 present busy tone, the tone is depend on your settings.

Speed Dial

1. Set Dial number to 123 on Phone-1 UI.

2. Set Real Number to 9887872 on Phone-1 UI.

3. Register a phone number is 9887872 for Phone-2.

4. Pick up Phone-1, Dial tone should be presented.

7. Dial the number 123, Phone2 should ring and Phone-1 should present ring back tone.

5. Pick up Phone-2. Ring back tone should be stopped in Phone-1 and bi-directional voice traffic should flow.

 Audio

DTMF Method

You can select different DTMF method here; there are three options InBand / RFC2833/ SIPInfo

Codec Setting

Codec Enable: There are three codecs supported: g711u/g711a/g729. Check the checkbox to enable or uncheck to disable.

Issue 01 (2015-07-10) Huawei Proprietary and Confidential

Priority: You can also set the priority of the codec

Ptime: It defines the length of time in milliseconds represented by the media in a packet. The ptime value tells the length of the speech block in the RTP packets. For the g711 u/a codecs,there are four options: 5/10/20/30ms; for the g729, there are three options: 10/20/30ms.

Issue 01 (2015-07-10) Huawei Proprietary and Confidential

4.1.7 Management>Diagnostics

This Diagnostics page will help you to perform a Ping or the Traceroute to troubleshoot the network connection.

− Diagnostics

 Ping Test

 IP address:

To issue a Test, please enter the destination IP address and Domain name here.

 Sending Count:

Please fill how many times the test need to be performed.

 Sending Buffer:

Please fill how many buffer you want to add in a range of 4~1472byte.

Example

If the CPE fails to access the Internet, run the ping command to preliminarily identify the problem. To do so:

1. Choose Management > Diagnostics. On the Diagnosis Tools, set to

Ping. The Ping page is displayed.

2. Enter the domain name in the IP Address field, for example, www.google.com.

3. Set Sending Count and Sending Buffer.

4. Click Run

5. Wait until the ping command is executed.

The execution results are displayed in the box.

 Traceroute

Issue 01 (2015-07-10) Huawei Proprietary and Confidential

 IP address:

To issue a Test, please enter the destination IP address and Domain name here.

 TTL:

Time To Live value; in the Traceroute test, please fill in a test value for the packet path time and check what is the path time that a packet takes to the specified host.

Example

If the CPE fails to access the Internet, run the traceroute command to preliminarily identify the problem. To do so:

1. Choose Management > Diagnostics. On the Diagnosis Tools, set to

Traceroute. The Traceroute page is displayed.

2. Enter the domain name in the IP Address field, for example, www.google.com.

3. Set TTL

4. Click Run

5. Wait until the traceroute command is executed.

The execution results are displayed in the box.

Ping page

Issue 01 (2015-07-10) Huawei Proprietary and Confidential

Trace route page

4.1.8 Management> System Log

The system log allows you can provide more detail information to your network provider.

System log will not be recorded any individual privacy.

Log level

There are four levels pre-defined: Critical/Error/Warning/Information, Please see below table.

 System Log

System

Information

. Start/Reboot/Reset

Connection

Manager

. WAN Connection

. WAN IP obtained

VoIP

. Started/Stopped

. Register to SIP server

. Call Out/In

. Call session established

Warning

. SIM card is not inserted

. Verify PIN failed

. Failed to register to SIP

. Failed to establish phone call

Error Critical

Issue 01 (2015-07-10) Huawei Proprietary and Confidential

Wi-Fi

FOTA

. Failed to send register message to

SIP server

. AP: started/stopped

. client: associated/disassociated

. client: unauthorized

. Started/Stopped

. Periodic Firmware check/upgrade result

. Starts download firmware

. Start upgrade firmware

. Failed to connect to server

. Failed to download

Packages or firmware

. Failed to upgrade firmware

. Failed to verify firmware

 Operation Log

Information Warning

Operation

. Web login/logout by user

. Web logout due to session timeout

. Web login password is changed

. DHCP server IP is changed

. Firewall level is changed

. Block/Un-block

DHCP client

. FW upgrade from UI

. WiFi SSID is changed

. WiFi security is changed

. Modify each page

. Start/Stop WPS

. Start/Stop Ping

. Start/Stop

Traceroute

. Export/Import

Configuration File

. Web login is failed

. User cancels the upgrade notification

. Firmware upgrade fail

Error

Issue 01 (2015-07-10) Huawei Proprietary and Confidential

Critical

Scroll Auto:

If you checked the Scroll Auto checkbox the syslog will always scroll to the bottom line to display the latest log

If you just want to view the previously log, please un-checked it.

Export:

You can export your syslog out for the further analysis or issue tracking; the export format will be the .txt file with .tar compress.

4.2 Personalization

4.2.1 Personalization>PIN Management

−

USIM status

This column will show current SIM card's status, detail definition as below:

USIM not inserted

Your SIM card is not insert or SIM Card not able to be detected properly.

USIM Ready

SIM card insert properly andbeendetected

Wait PIN /PUK code

SIM card is protected by PIN or PUK code, please go “U/SIM's PIN/PUK

Verification

” verify the code.

Issue 01 (2015-07-10) Huawei Proprietary and Confidential

You can only use your SIM card after verify the PIN or PUK code.

Your SIM card c an’t not use, please check your SIM card/Network provider.

Other Reason

−

USIM's PIN/PUK Verification

Only when your SIM card is locked by PIN/PUK code, the column will becomeactivate.

Please fillyourPINcodehere then press “Verify” button.PINcodeshould be 4-8 digits number.

If PIN retries error over 3 times, SIM card will be blocked and PUK code will be required to unblock the

SIM card. Normally, PUKcodeshould be 8 digits number. After PUK codeis filled, press

“Verify”to begin

PUK verification.

※If you are in the first time use, please check Network Provider to get your PIN/PUK code details.

−

USIM's PIN Management

If you select “enabled’, device will activate SIM PIN Code Lock function which will request you to fill-in the PINcodewhile every time device boot up. Please enter your PIN code (4~8digits number) then press “Apply” button to confirmed the PIN code lock.

If you select “disable”, device would disable the PIN code lock function, please press “Apply” button to confirm the change.

−

USIM's Change PIN

If the PIN Code Lock function isEnable, you can renew your PIN code here.

Please fill yourOld (Original) PIN code and New PIN code then confirm the New PIN code again, press ”Change” button to confirm the change.

Issue 01 (2015-07-10) Huawei Proprietary and Confidential

4.2.2 Personalization>Configuration

 Restore Factory Settings

You can use Reset Factory Settings function to set device to factory default settings. When returning to factory defaults, it will reset all the parameters/settings you had ever done. All the changes different from factory default settings will be lost; you will need to manually change the parameter again.

Restore Factory Settings

To restore settings to factory defaults, click the Restore Factory Settings button. After applying factory defaults, device will reboot.

 Export/Import Configuration File

Import/Export Password

Before export the file or import a file you need to input the password here (Password must contain 2 cases of uppercase letter, lowercase letter, number, space, and special characters(`~!@#$%^&*()-_=+\|[{}];:'",<.>/?).

Export Configuration File

You could export all of user settings in this device to a file.

Import Configuration File

You could browse a configuration file and import it back.

Issue 01 (2015-07-10) Huawei Proprietary and Confidential

4.2.3 Personalization>Device Setup

−

Password

You can change the default Graphical User Interface (GUI) access password here.

Password Maximum Length:

Please define the password maximum length here in a range of 6~128.

Old Login Password:

Input the original /current login password

New Login Password:

Enter a new log-in password you want to change, the new password total digits can

’t more than the value you set on the

”Password Maximum Length”column

Confirm New Login Password:

Enter the new password again for verification.

NOTE

If you don

’t fill any key in the Password field, it means that you don’t modify password.

−

Device Time

The modem uses the Simple Network Time Protocol (SNTP) to set its internal clock based on periodic updates from a time server. Maintaining an accurate time on the device will keep the system log to recording meaningful dates and times for event entries.

The Device Time area displays the following information:

Enable NTP

Allows user to connect what type of time server, if any.

Current Local Time

Displays the current time of the system clock.

Primary NTP Server

You can change the Primary NTP server if the default NTP server is not work.

Secondary NTP Server

You can set the secondary NTP server in case of the Primary NTP server didn’t work in some time.

Issue 01 (2015-07-10) Huawei Proprietary and Confidential

Time Zone

SNTP uses Greenwich Mean Time, or GMT (also known as Universal Time Coordinated, or

UTC) based on the time at the Earth's prime meridian, zero degrees longitude. To display a time corresponding to your local time, select your time zone from the pull-down list. The default is UTC-06.00, for Central Time (US and Canada.)

Auto Adjust for Daylight Saving Time

Select this check-box to set the daylight saving time if the unit operates in a region that observes daylight saving time.

−

Device Name

This area allows you to define a name that identifies your device. Using an easy-to-remember name instead of the default one, this can simplify the access to the device's GUI Setup menu. You can type the device name, followed by a dot symbol (.) in the address bar of the Web browser to login from LAN

(For example: http://huaweilte.).

The Device Name page displays the following information:

Current Device Name

Display current device name.

New Device Name

Enter a new name for your device (limits up to 20 ASCII printable characters) and click Apply.

Click Undo to clear the changes that you have made to this window.

Click Apply to activate your changes

Issue 01 (2015-07-10) Huawei Proprietary and Confidential

4.2.4 Personalization>Software

−

Upgrade From file:

Step 1:

ClickBrowserbutton to select the IPK file. (The IPK is the file with .ipkg, in each release you will get the ipk file release mtn_V100R001C01SPCxxx_arm.ipk)

Step 2:

Click Install Software button to install the selected IPK file.

−

Upgrade From FOTA: (Remote management server):

Please manually press “Check Version” button and device will request the latest update from the remote access server.

After checked,server will return message: Can't connect to Server/Latest Version, if your device SW is not up to date, you can do update or not.

NOTE

While FW is upgrading, please keep your device powering on. D on’t turn off the device to prevent the possible damage.

Issue 01 (2015-07-10) Huawei Proprietary and Confidential

4.3 Basic

4.3.1 Basic>Firewall

The modem provides extensive firewall protection by restricting connection parameters to limit the risk of intrusion and defending against a wide array of common hacker attacks.

This page is to configure and change the firewall settings. The firewall feature can be used to block unauthorized access and allowing only authorized communications from the Internet network. It also allows the device to be managed over the Internet by authorized user.

Current

Firewall Level

Shows the current device firewall level.

Firewall Level

Allows user to change the device firewall level here, there are four options pre-defined:

 Low (filtering disabled)

 Medium (standard)

 High

 Custom (If you chose Custom option, you can customize the MAC Filtering, IP Filtering and

URL Filtering options)

Filtering

Strategy

The filtering rules you set will take over the default inbound and outbound policies.

MAC Filtering

Block or allow the client device’s internet access via

MAC address, you can go Advanced>MAC Filter to edit

backlist or whitelist

IP Filtering

Block or allow the client device’s internet access via IP

address, you can go Advanced>IPFilter to edit backlist or

whitelist

URL Filtering

Block or allow the client device’s internet access via

URL(web address), you can go Advanced>URL Filter to edit backlist or whitelist

Issue 01 (2015-07-10) Huawei Proprietary and Confidential

DoS Attack

Block Denials of Service (DoS) attacks from the LAN and Internet, such as SYN floods and ping floods.

Block Anonymous Internet Requests

Select this check-box to reject anonymous Internet requests.

Filter Multicast

Select this check-box to filter out multicast packets.

Filter Internet NAT Redirection

NAT Redirection is used to block access to the local server from the local PC via unit's WAN IP. If this feature is enabled, local PC can only access the local server via unit's LAN IP.

Filter IDENT (Port 113)

Select this check-box to drop incoming packets from the unit WAN side with destination port 113.

Click Undo to clear the changes that you have made to this

window.

Click Apply to activate your changes.

Issue 01 (2015-07-10) Huawei Proprietary and Confidential

4.3.2 Basic>DMZ

For applications that require unrestricted access to the Internet, you can configure a specific client/server as a demilitarized zone (DMZ).

Enable DMZ

Select this check-box to enable or disable DMZ.

DMZ IP Address

Set a server that acts as a "neutral zone" (DMZ stands for "Demilitarized Zone") and separates an internal network from a public one in order to prevent outside access to private data. The DMZ forwards the network traffic to specific hosts based on the protocol and port number.

- Click Undo to clear the changes that you have made to this window.

- Click Apply to activate your changes.

Issue 01 (2015-07-10) Huawei Proprietary and Confidential

4.3.3 Basic>UPnP

UPnP

Enable UPnP IGD - Select this check-box to enable/disable Universal Plug and Play Internet Gateway

Device - a protocol that simplifies device connection and network implementation. When this option is enabled, certain Windows applications would setup the port forwarding rule dynamically.

- Click Undo to clear the changes that you have made to this window.

- Click Apply to activate your changes.

Issue 01 (2015-07-10) Huawei Proprietary and Confidential

4.3.4 Basic>Dynamic DNS

Dynamic Domain Name System (DNS) is a mechanism used for translating host names for network nodes into IP addresses in real-time. This page allows enabling the Dynamic DNS and selecting the service provider. The Dynamic DNS page includes the following parameters:

Enable DDNS

Select this check-box if the unit has a non-static IP address to keep the domain name associated with an ever-changing IP address.When DDNS is enabled, configure the following parameters:



Username



Password



Domain Name



Host Name

Service Provider

Select the DDNS service provider from the drop-down list.

- Click Undo to clear the changes that you have made to this window.

- Click Apply to activate your changes.

Issue 01 (2015-07-10) Huawei Proprietary and Confidential

4.3.5 Basic>VPN Passthrough

Enable IPSecPassthrough

Internet Protocol Security. IPSec provides encrypted security services at the IP layer, and enables to use encrypted tunnels/traffic between two hosts.

Enable PPTP Passthrough

Point to Point Tunneling Protocol; This protocol enables the transfer of data packets of TCP / IP through a foreign network that is not based on these protocols (by marking the packet with an address suited to the foreign network).

Enable L2TP Passthrough

Layer 2 Tunneling Protocol, an open standard with multivendor interoperability and acceptance.

- Click Undo to clear the changes that you have made to this window.

- Click Apply to activate your changes.

Issue 01 (2015-07-10) Huawei Proprietary and Confidential

4.4 Advanced

4.4.1 Advanced>MAC Filtering

You can block access to the Internet from clients on the local network by MAC addresses. In the MAC

Filter page you set MAC addresses to be filtered out by the security system. You can add addresses to the filtered group or delete them, and also enable or disable filtering at different times. The following configuration parameters are available:

Current MAC filtering status

Shows the MAC filtering function is disable or enable.

To enable or disable, you need to go to the Basic>Firewall level to change the firewall setting.

Low: Filtering disable

Medium: Filtering enable, you can set filtering by blacklist or whitelist on MAC filtering mode.

High: Filtering enable, you can set filtering by blacklist or whitelist on MAC filtering mode.

Custom: You can customize if you want to Disable or set Blacklist/Whitelist

MAC filtering mode

Select MAC filtering by Whitelist or Blacklist

 Blacklist: Block internet access which listed on the blacklist.

 Whitelist: Will ONLY allow the units listed on the list to access the network.

Select

Selecting this check-box and press Del button to delete this row.

MAC address:

Please key-in the client device which you want to do the MAC filtering MAC address.

Enabled

Select this check-box to enable/disable filter for the specific client device’s MAC address

Issue 01 (2015-07-10) Huawei Proprietary and Confidential

4.4.2 Advanced>IP Filtering

You can block access to the Internet from clients on the local network by specifying IP addresses and

TCP/UDP port numbers. You can configure up to five IP filters on the unit. In the IP Filter page you set IP addresses to be filtered out by the security system. You can add addresses to the filtered group or delete them. You can also enable or disable filtering at different times. The following configuration parameters are available:

Current IP filtering status

Shows the IP filtering function is disable or enable.

To enable or disable, you need to go to the Basic>Firewall level to change the firewall setting.

Low: Filtering disable

Medium: Filtering enable, you can set filtering by blacklist or whitelist on IP filtering mode.

High: Filtering enable, you can set filtering by blacklist or whitelist on IP filtering mode.

Custom: You can customize if you want to Disable or set Blacklist/Whitelist

IP filtering mode

Select IP filtering by Whitelist or Blacklist

 Blacklist: Block internet access which listed on the Blacklist.

 Whitelist: Will ONLY allow the unit listed on the Whitelist to access the network.

Select

Issue 01 (2015-07-10) Huawei Proprietary and Confidential

Selecting this check-box and press Del button to delete this row.

IP Range

Specify an IP address or range on the local network.

Port Range

Enter the port range to be filtered.

Protocol

Set the protocol to be filtered: TCP or UDP.

Enabled

Select this check-box to enable or disable filtering for the specific table entry.

- Use the Add or Del buttons to add the rule to the group or clear it from the group, please click Apply button to confirm the Add or Del.

- Click Undo to clear the changes that you have made to this window.

- Click Apply to activate your changes.

Issue 01 (2015-07-10) Huawei Proprietary and Confidential

4.4.3 Advanced>Port Forwarding

Port Forwarding instructs the router to which computer on the local area network to send data. According to the port forwarding rules or setup, the router sends the data from the external IP address: port number to an internal IP address: port number. Port Forwarding rules are created per port. The Port Forwarding page enables managing and setup of the rules for Port Forwarding. The following configuration parameters are available:

Select

Select this check-box and press Del button to delete this row.

Protocol

Set the protocol for port forwarding: TCP, UDP or Both.

WAN Port

Enter the port number for WAN side.

LAN Port

Enter theport number for LAN side.

LAN IP

Enter the IP address that identifies the IP subnet of the remote network.

Enabled

Select this check-box to enable/disable port forwarding for the specific IP.

- Use the Add or Del buttons to add the rule to the group or clear it from the group, please click Apply button to confirm the Add or Del.

- Click Undo to clear the changes that you have made to this window.

- Click Apply to activate your changes.

Issue 01 (2015-07-10) Huawei Proprietary and Confidential

4.4.4 Advanced>Port Trigger

Port triggering is a way to automate port forwarding: outbound traffic on predefined ports ('triggering ports') causes inbound traffic to specific incoming ports to be dynamically forwarded to the initiating host, while the outbound ports are in use. This allows computers behind a NAT-enabled router on a local network to provide services that would normally require the computer to have a fixed address on the local network. Port triggering can open an incoming port when a client on the local network makes an outgoing connection on a predetermined port or range of ports. In the Port Trigger page you can specify up to 15 rules with parameters for Port Triggering. The following configuration parameters are available:

Select

Select this check-box and press Del button to delete this row.

No.

Display the number of the port trigger rule.

Application Name

Enter a name for identifying this port trigger protocol.

Protocol

Set the protocol for port trigger: TCP, UDP or BOTH.

Triggered Range

Enter the trigger range (1~65535).

Forwarded Range

Enter the forwarded range (1~65535).

Enabled

Select this check-box to enable/disable port trigger for the specific application.

Issue 01 (2015-07-10) Huawei Proprietary and Confidential

- Use the Add or Del buttons to add the rule to the group or clear it from the group, please click Apply button to confirm the Add or Del.

- Click Undo to clear the changes that you have made to this window.

- Click Apply to activate your changes.

Issue 01 (2015-07-10) Huawei Proprietary and Confidential

4.4.5 Advanced>Layer 7

Select

Select this check-box and press Del button to delete this row.

No.

Display the number of the layer 7 rule.

Blocked Content

Enter the keywords that need to be filtered on layer 7. (Please double check your Capital and Lower case letters, it matters to the filtering result)

- Use the Add or Del buttons to add the rule to the group or clear it from the group, please click Apply button to confirm the Add or Del.

- Click Undo to clear the changes that you have made to this window.

- Click Apply to activate your changes.

Issue 01 (2015-07-10) Huawei Proprietary and Confidential

4.4.6 Advanced>URL Filtering

Current URL filtering status

Shows the URL filtering function is disable or enable.

To enable or disable, you need to go to the Basic>Firewall level to change the firewall setting.

Low: Filtering disable

Medium: Filtering enable, you can set filtering by blacklist or whitelist on IP filtering mode.

High: Filtering enable, you can set filtering by blacklist or whitelist on IP filtering mode.

Custom: You can customize if you want to Disable or set Blacklist/Whitelist

URL filtering mode

Select URL filtering by Whitelist or Blacklist

 Blacklist: Block internet access which listed on the Blacklist.

 Whitelist: Will ONLY allow the unit listed on the Whitelist to access the network.

Select

Select this check-box and press Del button to delete this row.

No.

Display the number of the URL filtering rule.

URL

Enter the URL or URL’s keywords that needs to be filtered. (Please double check your Capital and Lower case letters, it matters to filtering)

- Use the Add or Del buttons to add the rule to the group or clear it from the group, please click Apply button to confirm the Add or Del.

- Click Undo to clear the changes that you have made to this window.

- Click Apply to activate your changes.

Issue 01 (2015-07-10) Huawei Proprietary and Confidential

Select

4.4.7 Advanced>ACL Filtering

Select this check-box and press Del button to delete this row.

Name

Enter a name for identifying this ACL filter rule

; it is free defining with 10 units’ characters.

Direction

Define which direction for the filter

 LAN to Device

 LAN to WAN

 WAN to LAN

 WAN to Device

Src IP

Please define the start and end source IP address that the filter rule applies.

Src Port

Please fill in the source port number range.

Dst IP

Please define the start and end destination IP address that the filter rule applies.

Dst Port

Issue 01 (2015-07-10) Huawei Proprietary and Confidential

Please fill in the destination port number range.

Protocol

Please select which type of package for filtering.

 TCP

 UDP

 BOTH

Policy

Please define what action to do for the filtering.

 DROP

 ACCEPT

- Use the Add or Del buttons to add the rule to the group or clear it from the group, please click Apply button to confirm the Add or Del.

- Click Undo to clear the changes that you have made to this window.

- Click Apply to activate your changes.

Issue 01 (2015-07-10) Huawei Proprietary and Confidential

4.4.8 Advanced>Static Routing

Select

Select this check-box and press Del button to delete this row.

No.

Display the number of the Static Routing rule.

Destination IP Address

Please fill-in the destination IP address for the route.

Subnet Mask

Please fill-in the subnet mask of the destination IP network.

Gateway Interface

The gateway may be a router or switch on the same network segment as the device's

LAN/WAN/Tunnelinterface. Please indicate the interface for setting the route rule.

NOTE

This feature is supported under Gateway, Router andVPN modes. If it is enabled, the Static Routing setting page can be configured. If you set VPN for WAN operation mode the

“tunnel” option will show up for configuration.

- Use the Add or Del buttons to add the rule to the group or clear it from the group, please click Apply button to confirm the Add or Del.

- Click Undo to clear the changes that you have made to this window.

- Click Apply to activate your changes.

Issue 01 (2015-07-10) Huawei Proprietary and Confidential

4.5 WiFi

4.5.1 Wi-Fi>Basic

Enable Wi-Fi

Enables / disables the Wi-Fi radio.

 2.4GHz WiFi

Enable 2.4GHz WiFi

Enables / disables the 2.4GHz Wi-Fi radio.

Network Name(SSID)

The Service Set ID (SSID) that identifies the Wi-Fi network. The SSID is case sensitive and can consist of up to 32 alphanumeric characters.

Following characters is valid for Network Name (SSID).

' ( ) * - . / 0 1 2 3 4 5 6 7 8

9 : < = > @ A B C D E F G H I J

K L M N O P Q R S T U V W X Y Z

[ ] ^ _ ` a b c d e f g h i j k l m n o p q r s t u v w x y z {

| } ~

Hide SSID

This function is to allow you to hide the SSID to prevent the unexpected connection request, please checked the checkbox to hide the SSID and unchecked it to broadcast the SSID.

Encryption

Data passing between the unit and clients must be protected from interception and eavesdropping.

For a more secure network, the modem can implement one of several security mechanisms. The security mechanism employed depends on the level of security required, the network and management resources available, and the software support provided on wireless clients.

There are security options available. When you select the security type from the list, the required settings are displayed. The option "Open System" together with encryption disabled is equivalent to no security; all clients will be able to immediately connect to the Wi-Fi network.

The following security options are available for the Wi-Fi network.

-Open System

-Shared Key

-WPA2 PSK

Issue 01 (2015-07-10) Huawei Proprietary and Confidential

-WPA-WPA2-Mixed PSK

 5GHz WiFi

Enable 5GHz WiFi

Enables / disables the 2.4GHz Wi-Fi radio.

Network Name(SSID)

The Service Set ID (SSID) that identifies the Wi-Fi network. The SSID is case sensitive and can consist of up to 32 alphanumeric characters.

Following characters is valid for Network Name (SSID).

Hide SSID

This function is to allow you to hide the SSID to prevent the unexpected connection request, please checked the checkbox to hide the SSID and unchecked it to broadcast the SSID.

Encryption

Data passing between the unit and clients must be protected from interception and eavesdropping.

The following security options are available for the Wi-Fi network.

-Open System

-Shared Key

-WPA2 PSK

-WPA-WPA2-Mixed PSK

4.5.2 Wi-Fi>Advanced

 2.4GHz WiFi

Working mode

It shows what Wi-Fi standard protocol is supported 802.11 b/g/n is supported.

Radio Channel

The radio channel is used by the unit and its clients to communicate with each other. This channel must be the same on the unit and all of its wireless clients. The available channel settings are limited by local regulations.

Power Level

The power level High/Middle/Low stands for WiFiTx power, you can adjust it base on your environment condition.

AP Isolation

Issue 01 (2015-07-10) Huawei Proprietary and Confidential

When the AP isolation is set to OFF: All the connected Wi-Fi clients can ping each other.When the

AP isolation is set to ON: The Wi-

Fi clients can’t ping each other

ACL Settings

In this section you can add MAC addresses of clients which are allowed to access the system, or denied from accessing.

Step 1: Select either of Disable, Allow or Deny.

Step 2:

For the Allow and Deny lists, click Insert to add a MAC address to the list, and specify the details.

 5GHz WiFi

Working mode

It shows what Wi-Fi standard protocol is supported 802.11 a/n/ac is supported.

Radio Channel

Power Level

The power level High/Middle/Low stands for WiFiTx power, you can adjust it base on your environment condition.

AP Isolation

When the AP isolation is set to OFF: All the connected Wi-Fi clients can ping each other.When the

AP isolation is set to ON: The Wi-

Fi clients can’t ping each other

ACL Settings

In this section you can add MAC addresses of clients which are allowed to access the system, or denied from accessing.

Step 1: Select either of Disable, Allow or Deny.

Step 2:

For the Allow and Deny lists, click Insert to add a MAC address to the list, and specify the details.

- Click Undo to clear the changes that you have made to this window.

- Click Apply to activate your changes.

Issue 01 (2015-07-10) Huawei Proprietary and Confidential

4.5.3 Wi-Fi>WPS

PBC

User may connect multiple devices to the network and enable data encryption by pushing a button.

Users should be aware that during the two-minute setup period which follows the push of the button, unintended devices could join the network if they are in range.