Pentax Optio 550 Operating Manual

e01_kb338_OFC_IFC_41e.qk 3/17/03 3:31 PM Page 1
Digital Camera
Operating Manual
To ensure the best performance from
your camera, please read the Operating
Manual before using the camera.
e01_kb338_OFC_IFC_41e.qk 3/17/03 3:31 PM Page 2
Thank you for buying the Pentax Optio 550 Digital Camera. Please
read this manual before using the camera in order to get the most
out of all the features and functions. Keep this manual safe, as it
can be a valuable tool in helping you to understand all the camera’s capabilities.
Regarding copyrights
Images taken using the Optio 550 that are for anything other than personal
enjoyment cannot be used without permission according to the rights as
specified in the Copyright Act. Please take care, as there are even cases
where limitations are placed on taking pictures even for personal enjoyment
during demonstrations, industrial enterprise or as items for display. Images
taken with the purpose of obtaining copyrights also cannot be used outside
the scope of use of the copyright as laid out in the Copyright Act, and care
should be taken here also.
Regarding trademarks
•
•
•
•
The SD logo
is a trademark.
PENTAX is a trademark of PENTAX Corporation.
Optio is a trademark of PENTAX Corporation.
All other brands or product names are trademarks of registered trademarks of their respective companies.
• This product supports PRINT Image Matching II.
When used in combination, PRINT Image Matching II enabled digital still
cameras, printers and software help photographers to produce images
more faithful to their intentions.
Copyright 2001 Seiko Epson Corporation. All Rights Reserved.
PRINT Image Matching is a trademark of Seiko Epson Corporation.
e02_kb338_001_023_41e.qk 3/17/03 3:33 PM Page 1
FOR SAFE USE OF YOUR CAMERA
Sufficient attention has been paid to the safety of this product but please
pay particular attention to the warnings indicated by the following symbols
during use.
Warning These symbols indicate that it is possible that the
user may experience serious difficulties
if the warnings are not heeded.
Caution These symbols indicate that it is possible that the
user may experience minor or middling difficulties or
physical difficulties if the warnings are not heeded.
Warning:
• Do not attempt to take the camera apart or remodel the camera. High voltages are
present within the camera, and there is therefore a danger of electric shocks.
• If the inside of the camera should become exposed as a result of, for example, the
camera being dropped, please do not under any circumstances touch such exposed
portions, as there is a danger of receiving an electric shock.
• Wrapping the strap of the camera around your neck is also dangerous, please take
care that small children do not hang the strap around their necks.
• To avoid the risk of it being swallowed by mistake, keep the SD Memory Card out of
the reach of small children. Seek medical attention immediately if accidentally swallowed.
• Use an AC adapter that are of the power and voltage specified for exclusive use with
this product. The use of an AC adapter other than that specified exclusively for use
with this product may cause fire or electric shocks.
• If the camera emits smoke or a strange smell, or in the event of any other irregularity,
stop using the camera immediately, remove the battery or disconnect the AC adapter
and contact your nearest Pentax service center. Continued use of the camera may
result in fire or electric shock.
• Discontinue use of the AC adapter during thunderstorms. This can cause a fire or
electrical shock.
Caution:
• Never try to disassemble, short the battery. Also, do not dispose of the battery in fire,
as it may explode.
• Remove the battery from the camera immediately if it becomes hot or begins to smoke.
Be careful not to burn yourself during removal.
• Some portions of the camera heat up during use, so please take care, as there is a risk
of low temperature burns if such portions are held for long periods of time.
• Do not place your finger on the flash when it is discharging as there is a risk of burns.
• If any of the battery leakage should come in contact with your eyes, do not rub them.
Flush your eyes with clean water and get medical attention immediately.
• If any of the battery leakage should come in contact with skin or clothes, wash the
affected areas thoroughly with water.
1
e02_kb338_001_023_41e.qk 3/17/03 3:33 PM Page 2
Care to be Taken During Handling
• Do not clean the product with organic solvents such as thinner or alcohol benzene.
• Places of high temperature and humidity should be avoided. Particular care should be
taken regarding vehicles, which can become very hot inside.
• Storing the camera where pesticides and chemicals are handled should be avoided.
Remove from case and store in a well-ventilated place to prevent the camera from
becoming moldy during storage.
• Do not use the camera where it may come in contact with rain, water or any other
liquid, because the camera is not weather, water, or liquid resistant. Should the camera get wet from rain, splashing water, or any other liquid, wipe it off immediately with
a dry soft cloth.
• Ensure that the camera is not subjected to substantial vibrations, shocks or pressure.
Place the camera on a cushion for protection when the camera is subjected to the
vibrations of a motorbike, car, or ship, etc.
• The liquid crystal display will become black at temperatures of approximately 60°C
(140°F) but will return to normal when normal temperatures are returned to.
• The response speed of the liquid crystal display becomes slow at low temperatures.
This is due to the properties of the liquid crystal and is not a fault.
• Remove dust from the lens and viewfinder using a blower or clean off dust using a
lens brush.
• Periodic checks are recommended every 1 to 2 years in order to maintain highperformance.
• When the camera has not been used for a long time, confirm that it is still working
properly, particularly prior to taking important pictures (such as at a wedding or during travelling). Pentax is not responsible for consequential damages (costs incurred as
a result of taking pictures, loss of benefits that were to be obtained through taking pictures) arising from failure of this product.
• If the camera is subjected to rapid temperature changes, condensation may form on
the inside and outside of the camera. Therefore put the camera in a bag or plastic
bag, and take the camera out when the difference in temperature has subsided.
• The temperature range in which the camera can be used is 0°C to 40°C (32°F to
104°F).
• Avoid contact with garbage, dirt, sand, dust, water, toxic gases, salt, etc. as this may
cause damage to the camera. If rain or drops of water get onto the camera, please
wipe dry.
• Refer to “Precautions When Using an SD Memory Card/MultiMediaCard” (p.17) regarding the SD Memory Card/MultiMediaCard.
• Be sure to use the rechargeable lithium-ion battery D-LI7 provided for this camera. If
you use any other battery the camera may be damaged or malfunction.
2
e02_kb338_001_023_41e.qk 3/17/03 3:33 PM Page 3
To users of this camera
• There is a possibility that recorded data may be erased or that the camera may
not function correctly when used in surroundings such as installations generating
strong electromagnetic radiation or magnetic fields.
• The liquid crystal panel used in the LCD display is manufactured using extremely high precision technology. Although the level of functioning pixels is 99.99% or
better, you should be aware that 0.01% or fewer of the pixels may not illuminate
or may illuminate when they should not. However, this has no effect on the
recorded image.
• There is a possibility that the illustrations and the display screen of the LCD
monitor in this manual are different form the actual product.
3
e02_kb338_001_023_41e.qk 3/17/03 3:33 PM Page 4
Contents
FOR SAFE USE OF YOUR CAMERA ·····················································1
Care to be Taken During Handling ···························································2
Contents ···································································································4
Contents of the Operating Manual ···························································7
Checking the Contents of the Package ····················································8
Name of Parts ··························································································9
Names of Operating Parts ····································································10
Getting Started ············································································11
Attaching the Strap ··························································································11
Powering the Camera ······················································································12
Charging the Battery ··············································································12
Installing the Battery ··············································································13
Using the AC Adapter (optional) ····························································15
Installing the SD Memory Card/
MultiMediaCard ·······························································································16
Turning the Camera On and Off ······································································18
Adjusting the Viewfinder ··················································································19
Initial Settings ··································································································20
Setting the Display Language ································································20
Setting the Home Town ··········································································21
Setting the D.S.T. Mode ··········································································21
Setting the Date and Time ·····································································22
Quick Start ····················································································24
Taking Still Pictures ·························································································24
Playing Back Still Pictures ···············································································26
Playing Back Images ··············································································26
Playing Back Previous or Next Images ··················································26
How to View the Recorded Images ·································································28
Common Operations ···································································30
Changing the Mode ··························································································30
Using the Button Functions ··············································································31
Capture Mode ························································································31
Playback Mode ·······················································································33
Using the Menus ·····························································································34
How to Set the Menus ············································································34
Menu List ································································································36
Taking Pictures ············································································38
4
Displaying Shooting Information (Capture Mode) ············································38
Setting the Shooting Functions ········································································40
Selecting the Focus Mode ·····································································40
Selecting the Flash Mode ······································································42
Selecting the Recorded Pixels ·······························································43
Selecting the Quality Levels ···································································44
Adjusting the Color Balance according to Lighting (White Balance) ·····45
Changing the AF Area (Focusing Area) ·················································47
Setting the Light Metering Range to Determine the Exposure
(AE Metering) ·························································································48
e02_kb338_001_023_41e.qk 3/17/03 3:33 PM Page 5
Setting the Sensitivity ·············································································49
Setting the Instant Review time (Instant Review) ··································50
Setting the Image Sharpness (Sharpness) ············································51
Setting the Color Saturation (Saturation) ···············································52
Setting the Image Contrast (Contrast) ···················································53
Taking Pictures ·································································································54
Letting the Camera Set the Exposure (Program Mode) ························54
Setting the Aperture Value (Aperture Priority Mode) ·····························55
Setting the Shutter Speed (Shutter Priority Mode) ································56
Setting the Exposure Manually (Manual Exposure Mode) ·····················57
Selecting the Picture Mode According to the Shooting ························59
Scene (Picture mode) ············································································59
Taking Movie Pictures (Movie Picture Mode) ·········································61
Taking Panorama Pictures (Panorama Assist Mode) ·····························63
Taking Stereo Pictures (3D Image Mode) ··············································65
Taking Pictures with Digital Filters (Digital Filter Mode) ·························70
Using Preset Function Settings (User Mode) ········································72
Recording Sound (Voice Recording Mode) ············································73
Using the Zoom ······················································································74
EV Compensation ··················································································76
Using the Self-Timer ··············································································77
Using the Remote Control Unit (optional) ··············································78
Continuous Shooting ··············································································79
Taking Pictures at Fixed Intervals (Interval Shooting) ····························80
Superimposing One Picture on Top of Another
(Multiple Exposure Mode) ······································································82
Automatically Changing the Shooting Conditions (Auto bracket) ··········84
Taking Fast Forward Movie Pictures (Fast Fwd Movie) ·························86
Saving the Settings (Memory) ··········································································87
Saving the Menu Items (Memory) ··························································87
Registering Functions in User Mode ······················································88
Playback/Erasing ·········································································89
Playing Back Images and Sound ····································································89
Playing Back Still Pictures ······································································89
Zoom Display ·························································································89
Adding a Voice Memo ············································································90
Playing Back Movie Pictures ··································································91
Playing Back Sound ···············································································92
Playing back Shooting Information (Playback Mode) ·····························93
Nine-image Display ················································································94
Slideshow ·······························································································95
Erasing Images ·······························································································96
Erasing a Single Image or Sound ··························································96
Erasing All Images ·················································································98
Protecting Images from Deletion (Protect) ·············································99
Viewing Images on a TV ················································································100
Setting the Printing Service (DPOF) ·····························································101
Printing Single Image ···········································································101
Printing All Images ···············································································103
5
e02_kb338_001_023_41e.qk 3/17/03 3:33 PM Page 6
Viewing Images with your PC ·······································································104
About the included software ·································································104
System environment ············································································104
Installing the software ··········································································105
Displaying and copying images using ACDSee™ ·······························112
Joining panorama images using ACD photostitcher ····························113
Disconnecting the camera from your computer ···································116
Viewing Images with your Macintosh ····························································118
About the included software ·································································118
System environment ············································································118
Installing the software ··········································································118
Displaying and copying images using ACDSee™ ·······························120
Disconnecting the camera from your Macintosh ··································121
Editing/Settings ·········································································123
Editing Images ·······························································································123
Changing the Image Size ·····································································123
Trimming Images ··················································································125
Camera Settings ····························································································126
Formatting a SD Memory Card/MultiMediaCard ··································126
Changing the Sound Settings ······························································127
Setting the Date Style ··········································································129
Changing the Date/Time ······································································130
Setting the World Time ·········································································130
Changing the Display Language ··························································132
Changing the Video Output Format ·····················································132
Changing the Start-up Screen ·····························································133
LCD Power Saving (Sleep Timeout) ····················································134
Setting Auto Power Off ·········································································134
Setting the Quick Delete Function ·······················································135
Setting the Quick Zoom Function ·························································135
Registering Functions ··········································································136
Adjusting the Focus Limit ·····································································138
Resetting to Default Settings (Reset) ···················································138
Setting the Alarm ···························································································139
Checking the Alarm ··············································································139
Setting the Alarm ·················································································139
Turning the Alarm Off ···········································································140
Appendix ····················································································141
List of City Names ·························································································141
List of Menu Default Settings ········································································142
Adjustable [Rec.Mode] Menu Items by Shooting Mode ································144
Messages ······································································································145
Troubleshooting ·····························································································147
Optional Accessories ·····················································································150
WARRANTY POLICY ····················································································151
Main Specifications ·······················································································152
6
e02_kb338_001_023_41e.qk 3/17/03 3:33 PM Page 7
Contents of the Operating Manual
This Operating manual contains the following chapters.
Getting Started
This chapter explains what you need to do after purchasing the camera
before you start taking pictures. Be sure to read it and follow the instructions.
Quick Start
This chapter explains the simplest way to take pictures and play back images.
Use it if you want to start taking pictures straightaway. It also tells you how to
use the SD Memory Card/MultiMediaCard.
Common Operations
This chapter explains common operations such as the functions of the mode
dial and buttons, and how to use the menus. For more details, refer to the
respective [Taking Pictures], [Playback/Erasing] and [Editing/Settings] chapters.
Taking Pictures
This chapter explains the various ways of capturing images and
how to set the relevant functions.
Playback/Erasing
This chapter explains how to play back images on the camera or
on a TV and how to delete images.
Editing/Settings
This chapter explains how to edit images and set the camera-related functions.
Appendix
This tells you about the messages displayed on the LCD monitor and what
to do in the event of trouble.
The meanings of the symbols used in this Operating manual are
explained below.
☞
memo
Caution
indicates the reference page number for an
explanation of the related operation.
indicates information that is useful to know.
indicates precautions to be taken when
operating the camera.
The icons above the title show the Capture
modes, that can activate the function.
Contents of the Package
7
e02_kb338_001_023_41e.qk 3/17/03 3:33 PM Page 8
Checking the Contents of the Package
Camera
Optio 550
Lithium-ion battery
D-LI7
(Rechargeable) (∗)
Battery charger
(D-BC7) (∗)
USB cable
I-USB7 (∗)
AV cable
I-AVC7 (∗)
AC plug cord
D-C02 (∗)
3D Image Viewer
O-3DV1
Software (CD-ROM)
S-SW7
Strap
O-ST5 (∗)
Digital Camera
Operating Manual
To ensure the best performance from
your camera, please read the Operating
Manual before using the camera.
Operating Manual
this manual
8
About items marked with (∗)
∗ Items marked with (∗) are also available as optional accessories. For other optional accessories, refer to the list on page 150.
✽ Type of AC plug cord
D-CO2A Australia / D-CO2B United Kingdom / D-CO2E Europe / D-CO2H
Hong Kong / D-CO2J Japan / D-CO2K Korea / D-CO2U North America,
Canada
e02_kb338_001_023_41e.qk 3/17/03 3:33 PM Page 9
Name of Parts
Front
Remote control receiver
Shutter release button
Self-timer lamp
Power switch
Autofocus window
Speaker
Viewfinder
Built-in flash
Microphone
Lens
Back
Viewfinder
LCD monitor
Strap lug
Terminal cover
USB/AV output
terminal
DC input terminal
Battery lock lever
Battery chamber/card cover
Tripod socket
9
e02_kb338_001_023_41e.qk 3/17/03 3:33 PM Page 10
Names of Operating Parts
Diopter adjustment lever
/
button
/DPOF button
Power switch
Shutter release button
Mode dial
Zoom /
/
/
button
button
Playback button
OK button
Four-way controller
()
Display button
Status lamp (green)
Flash lamp (red)
Menu/Fn button
Guide indications
A guide to available button operation is displayed on the LCD monitor during
operation. The buttons are indicated as shown below.
Four-way controller ()
Four-way controller ()
Zoom / /
button (Only
for digital zoom and magnified playback)
DISPLAY button
Four-way controller ()
DPOF button
Four-way controller ()
Menu/Fn button
Shutter release button
10
button
button
OK button
e02_kb338_001_023_41e.qk 3/17/03 3:33 PM Page 11
Getting Started
Attaching the Strap
Getting Started
Pass the narrow end of the strap through the strap lug and pass
the other end through the loop.
11
e02_kb338_001_023_41e.qk 3/17/03 3:33 PM Page 12
Powering the Camera
Charging
indicator
Battery
To power outlet
c
x
Getting Started
Battery charger
z
AC plug cord
Charging the Battery
When using the camera for the first time or when the [Battery
depleted.] message is displayed, charge the battery.
z
x
c
v
memo
Caution
12
Connect the AC plug cord to the battery charger.
Plug the AC plug cord into the power outlet.
Place the battery in the charger with the label facing up.
The charging indicator lights red while the battery is charging
and changes to green when charging is completed.
When charging is completed, remove the battery from the
battery charger.
• The time required for full charge is about 180 minutes maximum.
The appropriate ambient temperature range for charging the
battery is 0°C-40°C (32°F to 104°F).
• The charging time may vary depending on the ambient temperature and charging conditions.
• When the battery reaches the end of its service life, the time
that the camera can be operated becomes shorter even when
the battery is fully charged. In this event, replace the battery.
• Always charge the battery after purchasing or when it has
not been used for a long time.
• Use the Battery charge D-BC7 to charge the rechargeable
Lithium-ion battery D-LI7 only as the charger may overheat
or be damaged.
• If the battery is inserted correctly but the charging indicator fails
to light, the battery may be faulty. Replace with a new battery.
e02_kb338_001_023_41e.qk 3/17/03 3:33 PM Page 13
x
z
Battery chamber
card cover
Battery
x
Installing the Battery
Getting Started
Battery
lock lever
Install the battery provided. When using the camera for the first
time, charge the battery before installing.
z
x
c
memo
Caution
Slide the battery chamber/card cover in the direction indicated by the arrow to open the battery chamber/card
cover.
Insert the battery with the label facing towards the lens
while using the side of the battery to press the battery
lock lever in the direction indicated by the arrow.
When you have inserted the battery, check that it is firmly
secured by the battery lock lever.
Close the battery chamber cover.
To remove the battery, release the battery by using your finger
to press the battery lock lever in the same direction as when
you inserted the battery, and pull the battery out.
If you intend to use the camera continuously for a long period, use
of the AC adapter D-AC7 (optional) is recommended. (☞ p.15)
• The rechargeable lithium-ion battery D-LI7 is exclusively for
powering this camera. If you use any other battery the
camera may be damaged or malfunction.
• Do not remove the battery when the camera is turned on.
• If you do not intend to use the camera for a long time,
remove the battery.
• If the camera is left without the battery for a long time, the
date setting will be reset.
• Insert the battery correctly. If the battery is incorrectly oriented, it may cause malfunction.
13
e02_kb338_001_023_41e.qk 3/17/03 3:33 PM Page 14
● Approximate Operating Time (when the D-LI7 battery is fully
charged)
Number of recordable images : Approx. 400 (when 50% shooting
uses flash, LCD monitor ON)
Playback time
: Approx. 210 min.
* The description above is based on Pentax measuring conditions and
may vary depending on capture mode and shooting conditions.
Getting Started
Caution
Generally, battery performance is temporarily deteriorate as
temperature decreases. When the camera is used in a cold
environment, keep this product warm by holding it in some
protection against cold or inside the clothes. Battery performance once deteriorated due to low temperature will be
recovered when the batteries are returned to room temperature.
● Battery Level Indicator
You can check the battery level by the
the LCD monitor.
symbol displayed on
(lit green)
: Adequate power remains.
(lit green)
: Battery is running low.
(lit yellow)
: Battery is running very low.
↓
↓
↓
(lit red)
: Battery is exhausted.
↓
[Battery depleted.] : After the message is displayed,
the camera will turn off.
14
e02_kb338_001_023_41e.qk 3/17/03 3:33 PM Page 15
AC adapter
To power outlet
v
z
x
AC plug cord
Using the AC Adapter (optional)
Getting Started
c
Terminal cover
If you intend to use the LCD monitor for a long time or connect the
camera to a PC, use of the AC adapter D-AC7 (optional) is recommended.
z
x
c
v
Caution
Make sure that the camera is turned off and opening the
terminal cover.
Connect the DC terminal on the AC adapter to the DC
input terminal on the camera.
Connect the AC plug cord to the AC adapter.
Plug the AC plug cord into the power outlet.
• Make sure that the camera is turned off when connecting
or disconnecting the AC adapter.
• Make sure that the AC plug cord and connecting cord are
inserted securely. If the cord becomes disconnected while
you are taking pictures, the data may be lost.
• When using the AC adapter D-AC7, be sure to read the
operating manual accompanying the AC adapter.
15
e02_kb338_001_023_41e.qk 3/17/03 3:33 PM Page 16
Installing the SD Memory Card/
MultiMediaCard
SD Memory Card/
MultiMediaCard
Battery chamber/
card cover
Getting Started
MultiMediaCards and the SD Memory Card can be used with this
camera. Captured images or recorded voice are recorded on the
SD Memory Card/MultiMediaCard. Make sure that the camera is
turned off before inserting or removing the SD Memory Card/
MultiMediaCard.
z Open the battery chamber/card cover.
x Rotate the card with the surface of the card having the symbol facing towards the lens and with the pin-connector edge of
the card towards the slot and insert fully until it clicks.
c
If the card is not inserted correctly, images and voice memos
may not be recorded properly.
Close the battery chamber/card cover.
To remove the card, eject the card by pressing it in the direction indicated by the arrow, and pull it out.
Approximate Number of Recordable Images and
Recorded pixels/Quality levels
Quality levels
Best
Better
Good
Movie images
voice
()
()
()
(320 × 240) recording
Recorded pixels
2592 × 1944
Approx. 4 Approx. 8 Approx. 14
16
2048 × 1536
Approx. 7 Approx. 12 Approx. 18
1600 × 1200
Approx. 11 Approx. 20 Approx. 27
1024 × 0768
Approx. 25 Approx. 45 Approx. 56
0640 × 0480
Approx. 53 Approx. 82 Approx. 100
Approx.
40sec.
Approx.
30min.
• The above table indicates the number of images when using a 16MB
SD Memory Card.
• As TIFF data is uncompressed, it cannot be stored on a 16MB SD
Memory Card/MultiMedia card. To take pictures in TIFF format, use a
card with a capacity of 32MB or more.
• The above table is based on standard shooting conditions specified by
PENTAX and may vary depending on the subject, shooting conditions,
capture mode, SD Memory Card, etc.
e02_kb338_001_023_41e.qk 3/17/03 3:33 PM Page 17
Precautions When Using a SD Memory Card/MultiMediaCard
• Make sure that the camera is turned off before opening the battery chamber/card cover.
Write-pro• The SD Memory Card is equipped with a write-protect switch.
tect switch
Setting the switch to [LOCK] protects the existing data by prohibiting recording of new data, deletion of existing data or formatting of the card.
Getting Started
• The SD Memory Card/MultiMediaCard formatted by the other equipment than
this camera cannot be used for PC, etc. Formatting must be done by this
camera.
• Care should be taken if you remove the SD Memory Card/MultiMediaCard
immediately after using the camera, as the card may be hot.
• Do not remove the SD Memory Card/MultiMediaCard or turn the camera off
while data is being recorded on the card or transferred to PC using USB
cable as this may cause the data to be lost or the card to be damaged.
• Do not bend the SD Memory Card/MultiMediaCard or subject it to violent
impact. Keep it away from water and store away from high temperature.
• Be sure to format unused SD Memory Card/multimedia cards or SD Memory
Card/multimedia cards that have been used on another camera. Refer to
“Formatting a SD Memory Card/MultiMediaCard” (p.126) for instructions on
formatting.
• Never remove the SD Memory Card/MultiMediaCard during formatting as this
may cause the card to be damaged and become unusable.
• The data on the SD Memory Card/MultiMediaCard may be erased in the following circumstances. Pentax does not accept any liability for data that is
erased
• when the SD Memory Card/MultiMediaCard is mishandled by the user.
• when the SD Memory Card/MultiMediaCard is exposed to static electricity or
electrical interference.
• when the card has not been used for a long time.
• when the card is ejected, the AC adapter is disconnected or the battery is
removed while the data on the card is being accessed.
• The SD Memory Card/MultiMediaCard has a limited service life. If it is not
used for a long time, the data on the card may become unreadable. Be sure
to make a backup of important data on a PC.
• Avoid using or storing the card where it may be exposed to static electricity or
electrical interference.
• Avoid using or storing the card in direct sunlight or where it may be exposed
to rapid changes in temperature or to condensation.
17
e02_kb338_001_023_41e.qk 3/17/03 3:33 PM Page 18
Turning the Camera On and Off
z Power switch
Getting Started
z
Press the power switch.
The camera will turn on.
When the camera is turned on the lens cover opens and
the lens extends.
Press the power switch again to turn the camera off.
Card Check
When the camera is turned on, it automatically performs a card check. If no SD
Memory Card/MultiMediaCard has been
inserted,
appears on the LCD monitor.
1/250
F2.8
And if the write-protect switch is set to
LOCK,
will be displayed instead of
, and the images or sound cannot be recorded.
18
000
02/20/2003
11:19
e02_kb338_001_023_41e.qk 3/17/03 3:33 PM Page 19
Adjusting the Viewfinder
z
Viewfinder
z
Getting Started
If the subject through the viewfinder are hard to see, you can
adjust the diopter in the range of –3 m–1 to +1 m–1 (per meter).
Aim the camera at the bright subject. While looking
through the viewfinder, move the diopter adjustment
lever to the left or right until the subject appears in the
sharpest focus.
For easy adjustment, point the camera at a subject with
clearly defined outlines.
19
e02_kb338_001_023_41e.qk 3/17/03 3:33 PM Page 20
Initial Settings
Power switch
Getting Started
Four-way controller
OK button
Display button
Menu button
If the initial settings screen appears when you turn the camera
on, follow the procedure below to set the display language,
Home Town, DST, video output format and current date and
time. If the date and time that appear at the bottom right of the
LCD monitor when you turn the camera on for the first time is
not the current time, follow the instructions for “Changing the
Date/Time” (p.130) to set the correct date and time.
Setting the Display Language
You can choose the language in which the menus, error messages, etc. are displayed from the following: English, French,
German, Spanish, Italian and Japanese.
z
x
c
memo
20
Turn the camera on.
Use the four-way controller ()
to select the display language.
The default setting is English.
Press the four-way controller ().
The screen for setting the next item
will be displayed.
Initial settings
Language/
City
DST
MENU
Exit
English
NYC
OK
• You can change the setting after it has been made. Refer to
“Changing the Display Language” (p.132).
Ok
e02_kb338_001_023_41e.qk 3/17/03 3:33 PM Page 21
Setting the Home Town
You can choose the city (Home Town) in
which you will use the camera.
Language/
English
City
DST
NYC
z
Press the four-way controller ()
to select the desired city (Home
Town).
x
Press the four-way controller ().
The screen for setting the next item will be displayed.
MENU
Exit
OK
Ok
• See p.141 for the list of cities and corresponding code names.
• You can change the setting after it has been made. Refer to
“Setting the World Time” (p.130).
Getting Started
memo
Initial settings
Setting the D.S.T. Mode
You can choose whether or not to display the
Saving Time) mode.
z
x
Use the four-way controller ()
to select
or
.
The default setting is
(Off).
Initial settings
Language/
Press the four-way controller ().
The screen for setting the next item
will be displayed.
City
DST
MENU
memo
(Daylight
Exit
English
NYC
OK
Ok
• You can change the setting after it has been made. Refer to
“Setting the World Time” (p.130).
21
e02_kb338_001_023_41e.qk 3/17/03 3:33 PM Page 22
Setting the Date and Time
Set the current date and time.
z
Use the four-way controller ()
to change the month.
Date Adjust
01 / 01 / 2003
Getting Started
0 : 00
MENU
x
Press the four-way controller ().
and will be displayed above
and below the day.
Use the four-way controller ()
to change the day and press the
four-way controller ().
and will be displayed above
and below the year.
Repeat Step c to change the
[year] [hour] and [minutes].
12/24
OK
Ok
OK
Ok
OK
Ok
OK
Ok
OK
Ok
02 / 01 / 2003
0 : 00
Exit
DISP
12/24
Date Adjust
02 / 20 / 2003
0 : 00
MENU
v
DISP
Date Adjust
MENU
c
Exit
Exit
DISP
12/24
Date Adjust
02 / 20 / 2003
0 : 00
MENU
b
Use the Display button to select
the 12-hour or 24-hour display
format.
DISP
12/24
Date Adjust
02 / 20 / 2003
11 : 19
MENU
22
Exit
Exit
DISP
PM
12/24
e02_kb338_001_023_41e.qk 3/17/03 3:33 PM Page 23
n
• For an accurate time setting, when you have finished the settings, press the OK button when the clock reaches 00 seconds.
• When the initial settings screen is displayed, you can cancel
the settings operation and switch to Capture mode by pressing the MENU/Fn button. If this is done, the initial settings
screen will be displayed next time you turn the camera on.
• You can change the settings after they have been made.
Refer to “Changing the Date/Time” (p.130).
Getting Started
memo
When you have finished the settings, press the OK button when the clock reaches 00 seconds.
The camera is ready to take a picture.
When you set date and time except the initial settings,
press the OK button again after pressing the OK button
when the clock reaches 00 seconds to return to capture
mode.
23
e03_kb338_024_037_41e.qk 3/17/03 3:37 PM Page 24
Quick Start
Taking Still Pictures
Shutter
release button
Mode dial
Power switch
Viewfinder
Zoom /
/
button
Quick Start
LCD monitor
For the simplest procedure to take still pictures:
The flash fires automatically depending on the light conditions.
z
x
c
Press the power switch.
The camera will turn on.
Set the mode dial to
200
.
Confirm the subject and shooting information on the LCD
monitor.
The focus area in the middle of
the LCD monitor indicates the
zone of automatic focusing. You
can change the size of the subject by pressing the Zoom button.
1/250
F2.8
02/20/2003
11:19
Focus Area
: makes the subject bigger.
: makes the subject smaller.
You can check the size of the subject by looking through
the viewfinder.
memo
24
As there is no focus area in the viewfinder, be sure to
check the focusing area on the LCD monitor.
e03_kb338_024_037_41e.qk 3/17/03 3:37 PM Page 25
v
Press the shutter release button.
The image will be displayed on the LCD monitor for 2
seconds (Instant Review) and recorded on the SD
Memory Card/MultiMediaCard. (The green and red
lamps on the right of the viewfinder blink alternately
while the image is being recorded on the SD Memory
Card/MultiMediaCard.)
Using the Shutter Release Button
status
lit
blink
Focus status lamp (green)
Subject is in focus
Subject is out of focus
Quick Start
The shutter release button works in a two-step action.
Press halfway
When the shutter release button is pressed lightly
(halfway), the focus and exposure are locked.
They remain locked while the button is pressed halfway,
and the shutter speed and aperture are displayed on the
LCD monitor.
You can find the following information on the LCD monitor,
the status lamp and the flash lamp.
Autofocus area
If the subject is in focus, the frame will light green. If the
subject is out of focus, the frame will not appear.
Focus status lamp & Flash status lamp
Flash status lamp (red)
Flash is charged
Flash is charging
You cannot take a picture while the flash is charging.
Pressed down fully
The picture is taken.
Instant Review
The Instant Review default setting is 2 seconds. During this
time you can delete the image by pressing the
button
(The [Delete] menu will be displayed.), and selecting
[Delete], and then pressing the OK button. To start recording
a voice memo, press the OK button during Instant Review.
Press the OK button again to stop recording.
Setting the Instant Review Time ☞ p.50
25
e03_kb338_024_037_41e.qk 3/17/03 3:37 PM Page 26
Quick Start
Playing Back Still Pictures
LCD monitor
Playback button
Four-way controller
Quick Start
Playing Back Images
You can display the still picture.
z
Press the Playback button after taking a picture.
The image taken will be displayed on the LCD monitor.
Playing Back Previous or Next Images
Still images can be played back one at a time, proceeding
either forward or backward.
z
x
Press the Playback button after taking a picture.
An image will be displayed on the LCD monitor.
Press the four-way controller ().
displays the previous image.
displays the next image.
26
e03_kb338_024_037_41e.qk 3/17/03 3:37 PM Page 27
Erasing the image displayed on the LCD monitor
memo
File No.
100-0020
Delete
Cancel
MENU
Exit
OK
Ok
• When you turn the camera on while pressing the Playback
button, the camera turns on in Playback Only mode. As
the lens does not extend in Playback Only mode, this feature is useful when you want to pass the camera to someone and show them the picture you have just taken. To
switch to the Capture mode, turn the camera off and then
turn it on again.
• You can enlarge the image displayed on the LCD monitor
by pressing the Zoom/ / button.
• When the screen is changed to the playback screen, the
image with the largest file number will be displayed first.
• In the case of movie pictures, the first frame will be displayed.
• If there are no images stored, the [No image] message
will be displayed.
Quick Start
While the image is displayed, you
can erase it by pressing the
button (The Delete screen will be displayed.), press the four-way controller
() to select [Delete], and then
pressing the OK button.
Press the Playback button or press
the shutter release button halfway to
return to shooting status.
Zoom Display ☞ p.89
Adding a Voice Memo ☞ p.90
27
e03_kb338_024_037_41e.qk 3/17/03 3:37 PM Page 28
Quick Start
How to View the Recorded Images
Images taken with the Optio 550
camera are recorded on the SD
Memory Card/MultiMediaCard. You
can view the images recorded on
the card on the camera itself, transfer them to your PC and print them
out.
Quick Start
Viewing images on the camera
One of the advantages of a digital
camera is that it enables you to view
your pictures immediately after you
have taken them. You can check the
composition and focus and take the
picture again if you are not satisfied.
Playing Back Images and Sound
☞ p.89~p.95
Viewing images on a TV
If you want to show your pictures to friends, you can display
them on your TV monitor. To view images on your TV, connect the camera to the TV with the AV cable.
Viewing Images on a TV
28
☞ p.100
e03_kb338_024_037_41e.qk 3/17/03 3:37 PM Page 29
Viewing images on a PC
☞
p.104
Viewing Images with your PC
p.118
Viewing Images with your Macintosh
☞
Quick Start
You can view recorded images and edit them on the PC just
by connecting the camera to the PC with the USB cable and
downloading the images (you need to install the USB driver if
you are using Windows 98). Or you can remove the SD
Memory Card/MultiMediaCard from the camera and transfer
the data to your PC using a card reader. If you use a laptop
computer, you can transfer the image data by fitting the SD
Memory Card/MultiMediaCard into the card adapter and
inserting the card adapter into the card slot.
Printing images by a printing service
Prints of images recorded on the SD Memory
Card/MultiMediaCard can be ordered in the same way as
with conventional photographs by taking the SD Memory
Card/MultiMediaCard to a store that performs printing.
The number of prints can be specified and dates can be included in the prints if DPOF (Digital Print Order Format) is set before
taking the SD Memory Card/MultiMediaCard to a store that performs DPOF printing.
Setting the Printing Service
☞ p.101
29
e03_kb338_024_037_41e.qk 3/17/03 3:37 PM Page 30
Common Operations
Changing the Mode
Capture mode is for taking pictures and voice recording.
Playback mode is for playing back or erasing images and
sound.
Switching Between Capture Mode and Playback Mode
• To change from Capture mode to Playback mode, press the
Playback button.
• To change from Playback mode to Capture mode, press the
Playback button or the shutter release button halfway.
Selecting the Capture Mode
Common Operations
z
Turn the mode dial so that the mark is on
or .
Manual exposure
Shutter priority
Aperture priority
Program
Picture
You can set the aperture manually, and
the shutter speed is set automatically.
The shutter speed and aperture are set
automatically when taking still pictures.
You can select a shooting mode from 9
modes according to the scene you are taking.
p.57
p.56
p.55
p.54
p.59
This mode is for taking moving
images. (Sound can also be recorded.)
This mode is for taking panorama
pictures.
p.61
3D
This mode is for taking 3D pictures.
p.65
Digital filter
This mode is for taking pictures using a variety of filters such as red, blue and green.
The functions are set in advance and the settings
are enabled whenever the camera is turned on.
This mode is for recording sound.
p.70
Movie picture
Panorama
User mode
Voice recording
30
You can set the shutter speed and
aperture manually.
You can set the shutter speed manually,
and the aperture is set automatically.
p.63
p.72
p.73
e03_kb338_024_037_41e.qk 3/17/03 3:37 PM Page 31
Using the Button Functions
Diopter adjustment lever
Adjusts the viewfinder for optimum clarity. (☞ p.19)
button
Changes the flash mode. (☞ p.42)
button
Changes the shooting mode as follows.
Using the self-timer (☞ p.77)
Using the remote control unit (☞ p.78)
Continuous shooting (☞ p.79)
Multiple exposure shooting (☞ p.82)
Interval shooting (☞ p.80)
*When the Capture mode is set to
, continuous
shooting, multiple exposure shooting and Interval shooting
mode will be skipped.
button
Changes the focus mode. (☞ p.40)
Zoom button
Changes the size of the subject. (☞ p.74)
Common Operations
Capture Mode
31
e03_kb338_024_037_41e.qk 3/17/03 3:37 PM Page 32
Playback button
Switches to Playback mode. (☞ p.30)
Four-way controller ()
Common Operations
32
Changes the EV compensation in modes other than
and
. (☞ p.76)
Changes the shutter speed in
mode. (☞ p.57)
Four-way controller ()
Adjusts the focus in
mode. (☞ p.41)
Sets the aperture value in
mode. (☞ p.57, 55)
and
Sets the shutter speed in
mode. (☞ p.56)
Selects the type of filter in
mode. (☞ p.70)
Selects Picture mode in
mode. (☞ p.59)
OK button
Sets the selected menu item. (☞ p.34)
When pressed in
mode, the function on the four-way
controller () reverts to the function set by the mode dial.
Display button
Changes the information displayed on the LCD monitor.
(☞ p.38)
Menu/Fn button
Displays the active menus in Capture mode and retrieves the
functions registered on the four-way controller. (☞ p.34, 137)
e03_kb338_024_037_41e.qk 3/17/03 3:37 PM Page 33
Playback Mode
button
Protects the image from erasure. (☞ p.99)
DPOF button
Sets the DPOF data for printing pictures. (☞ p.101)
button
Deletes the image. (☞ p.96)
Zoom / /
button
displays nine images at once. (☞ p.94)
Press –
in normal mode to change the size of the Zoom
Display image, displayed on the LCD monitor. (☞ p.89)
Playback button (☞ p.30)
Switches to Capture mode.
Four-way controller ()
Displays images one by one. (☞ p.26)
OK button
Saves the function selected by the menu item. (☞ p.34)
When pressed in Normal Playback mode, the voice memo
starts, and when pressed again, the voice memo stops.
(☞ p.90)
When pressed in Zoom Display or Nine-image Display mode,
changes to Normal Playback mode. (☞ p.89, 94)
Display button
Changes the information displayed on the LCD monitor. (☞ p.93)
Menu/Fn button
Displays the active menus in Playback mode. (☞ p.34)
Common Operations
33
e03_kb338_024_037_41e.qk 3/17/03 3:37 PM Page 34
Using the Menus
When you press the Menu/Fn button, the menus are displayed on the
LCD monitor. You can set functions, save the settings, and change the
camera settings on these menus.
How to Set the Menus
When you are making settings from a menu, a guide to operation is displayed on the LCD monitor.
z
Common Operations
x
Press the four-way controller ().
Use the four-way controller () to select the menu screen.
c
Use the four-way controller () to select an item.
Use the four-way controller () to move the frame up or
down.
v
v’
b
Caution
34
Press the Menu/Fn button.
The menu screen will be displayed. The selected area will
be underlined in green.
Use the four-way controller () to change the setting.
If there is a select screen, use the four-way controller ()
to move to the select screen.
Press the OK button.
The settings will be saved and the screen will return to capture or playback status.
If the menu screen is not exited, press the OK button again.
• If you press any buttons except the OK button before
press the OK button and leave the menu screen, any
changes to setting will not be saved.
• Even if you press the OK button and leave the menu
screen, if you remove the battery before turning off the
camera or do not otherwise turn off the camera correctly,
any changes to setting will not be saved.
e03_kb338_024_037_41e.qk 3/17/03 3:37 PM Page 35
Example of menu operation
z Menu/Fn button
x
[
[
Rec.Mode] menu
Playback] menu
1/3
MENU
[
Set-up] menu
Playback
Rec. Mode
Recorded Pixels
Quality Level
White Balance
Focusing Area
AE Metering
Sensitivity
Resize
Trimming
Alarm
Slideshow
2592 1944
AWB
Wide
Set-up
Format
Sound
Date Style
Date Adjust
World Time
Language/
Off
3sec
Auto
Exit
OK
MENU
Ok
Exit
OK
Ok
1/3
MENU
Exit
mm/dd/yy
1/ 1/2003
Off
English
OK
Ok
c
Rec. Mode
1/3
MENU
2592 1944
Common Operations
Recorded Pixels
Quality Level
White Balance
Focusing Area
AE Metering
Sensitivity
AWB
Wide
Auto
Exit
OK
Ok
v
c
Rec. Mode
Rec. Mode
Recorded Pixels
Quality Level
White Balance
Focusing Area
AE Metering
Sensitivity
1/3
MENU
Recorded Pixels
Quality Level
White Balance
Focusing Area
AE Metering
Sensitivity
2592 1944
AWB
Wide
Auto
Exit
OK
1/3
Ok
MENU
2592 1944
AWB
Wide
Auto
Exit
OK
Ok
v’
c
Select screen
Interval Shoot
Rec. Mode
Auto Bracket
Digital Zoom
Instant Review
Interval Shoot
Fast Fwd Movie
3D Mode
2/3
MENU
Exit
Interval
On
2sec
1min 10sec
Number of Shot
02
Off
Parallel
OK
Start Time
0hr 0min
Ok
MENU
Exit
OK
Ok
c
To the next screen
•
memo
•
If you press the shutter release button halfway and move the camera to
Capture mode, any changes to the setting will not be saved.
When you display the menu from Capture mode, the [
Rec. Mode] menu
will be displayed, and when you display the menu from Playback mode, the
[
Playback] menu will be displayed.
35
e03_kb338_024_037_41e.qk 3/17/03 3:37 PM Page 36
Menu List
[
Rec.Mode] Menu
Item
Description
Reference
Common Operations
Recorded Pixels
For selecting the size of recorded pixels.
p.43
Quality Level
For selecting the image compression rate.
p.44
White Balance
For adjusting the color balance according to lighting.
p.45
Focusing Area
For changing the Area of the autofocus.
p.47
AE Metering
For setting the metering method to determine the exposure.
p.48
Sensitivity
For setting the sensitivity.
p.49
Auto Bracket
For setting the shooting conditions such as exposure, saturation and
sharpness.
p.84
Digital Zoom
For taking digital zoom pictures.
p.75
Instant Review
For setting the instant review time.
p.50
Interval Shoot
For taking pictures specified interval of time.
p.80
Fast Fwd Movie
For delaying the frame rate when taking movie pictures (so that the
movie appears speeded up when played back)
p.86
3D Mode
For taking 3D pictures.
p.65
Memory
For saving the shooting function settings when the camera is turned
off.
p.87
Sharpness
For setting the sharpness.
p.51
Saturation
For setting the saturation.
p.52
Contrast
For setting the contrast.
p.53
USER
For setting the functions registered in User mode.
p.88
Please refer to pages 142 to 144 for List of Menu Default settings and the adjustable
[Rec. mode] menu items by shooting mode.
36
e03_kb338_024_037_41e.qk 3/17/03 3:37 PM Page 37
[
Playback] Menu
Item
Description
Reference
Resize
For changing the size of images
p.123
Trimming
For trimming images
p.125
Alarm
For setting the alarm to ring at specified time
p.139
Slideshow
Recorded images are played successively.
p.95
[
Set-up] Menu
Item
Description
Reference
For formatting the SD Memory Card/MultiMediaCard
p.126
Sound
For adjusting the beep sound when a button is pressed
For setting the button operation, start-up, shutter sounds and volume.
p.127
Date Style
For setting the date style
p.129
Date Adjust
For adjusting the date and time
p.130
World Time
For setting the world time
p.130
Language/
For changing the language in which menus and messages are displayed
p.132
Start-up screen
For setting the Start-up screen when the camera is turned on
p.133
Video Out
For setting the video output format
p.132
Sleep Timeout
For setting the power saving function
p.134
Auto Power Off
For turning off the power automatically.
p.134
Quick Delete
When this option is turned on, the Delete screen is displayed with
[Delete] or [All Images] selected.
p.135
Quick Zoom
For playing back images at the maximum zoom size with the Zoom
button pressed only once.
p.135
Fn Setting
For registering a function on the four-way controller.
p.136
Focus Limiter
For switching between limiting and not limiting lens movement during normal shooting and macro shooting.
p.138
Reset
For returning the camera settings to defaults
p.138
Common Operations
Format
37
e04_kb338_038_088_41e.qk 3/17/03 5:22 PM Page 38
Taking Pictures
Displaying Shooting Information (Capture Mode)
You can display information on the LCD monitor when shooting.
The display mode can be changed by pressing the Display button.
123 4 5
Display On
Shooting information is displayed.
q Flash mode w Drive mode
e Focus mode r Capture mode
t AF area
y Number of images can be taken
u Data & time i Battery indicator
6
198
02/20/2003
11:19
8
➞
Taking Pictures
1 23
035
2592
AWB
AUTO
6 54
➞
Histogram Display
The brightness distribution of the image is displayed.
The x-axis shows the brightness (darkest at the left end and brightest at the
right end) and the y-axis shows the
pixel numbers.
q Recorded pixels w Quality level
e White balance r AE metering
t Sensitivity y Histogram
• When the focus mode is set to
Autofocus mode, the AF area
frame is displayed.
7
Grid Display
The grid is displayed. This is useful for
composing detailed pictures.
• When the focus mode is set to
Autofocus mode, the AF area
frame is displayed.
➞
Go to next page
38
e04_kb338_038_088_41e.qk 3/17/03 5:23 PM Page 39
➞
Display Off
No shooting information is displayed.
• The AF area in autofocus mode is
displayed.
• If any of the modes are changed
such as Flash mode, the mode you
have changed is displayed for a
few seconds.
LCD Monitor Off
Turn off the LCD monitor.
(The LCD monitor is not turned off in
Playback mode.)
➞
Caution
The LCD monitor does not turn off in
Saving the Display Mode
☞ p.87
mode.
Taking Pictures
Display On
39
e04_kb338_038_088_41e.qk 3/17/03 5:23 PM Page 40
Setting the Shooting Functions
z
Selecting the Focus Mode
Focus Mode
(No icon) Autofocus mode
Taking Pictures
The camera is focused on the subject in the autofocus area when the shutter release button is pressed
halfway. Use this mode when the distance to the
subject is more than 60 cm (1.97 ft).
Macro mode
This mode is used when the distance to the subject
is approx. 15 cm – 65 cm (0.5 ft – 2.13 ft).
Super macro mode
This mode is used when the distance to the subject
is approximately 2 cm – 65 cm (0.8 inch – 2.13 ft).
Infinity-landscape mode This mode is used for taking distant objects.
Move focusing area
The position of the autofocus area is changed.
Manual focus mode
Adjust focus manually by the four-way controller
().
z
Press the
or
button in Capture mode.
The focus mode changes each time the button is pressed
and the set focus mode is displayed on the LCD monitor.
The camera is ready to take the picture in the set focus
mode.
• The default setting of the focus mode is [Autofocus mode].
memo • When the Movie picture mode is selected, (
☞ p.61) the posi-
40
tion of the autofocus area cannot be changed.
• The zoom is fixed in the wide-angle position in Super Macro
mode.
• If you use the flash in Macro mode, the image may be overexposed or a dark area may appear at the bottom right of the
picture.
• The flash does not discharge in Super macro mode.
e04_kb338_038_088_41e.qk 3/17/03 5:23 PM Page 41
Caution
If you take a picture while looking through the viewfinder
when the focus mode is set on Macro or Super Macro, the
range of the resulting picture will differ from what was seen
in the viewfinder.
Be sure to check the image on the LCD monitor.
Manual Focus
When the mode is set on
and press the four-way controller
(), the central portion of the picture is enlarged to full screen
on the LCD monitor. Adjust the focus with the four-way controller
while looking at the image on the monitor.
For distant focus
For closer focus
memo
• Keep pressing the four-way controller () will move the
focusing position rapidly.
• The central portion of picture is also enlarged in the Digital
zoom mode except at maximum magnification.
Saving the Focus Mode
☞ p.87
Taking Pictures
After the focus is set, press any buttons except the four-way controller () or take a finger off from the four-way controller ( ),
the screen returns to the normal display two seconds later.
41
e04_kb338_038_088_41e.qk 3/17/03 5:23 PM Page 42
z
Selecting the Flash Mode
(No icon) Auto flash
Taking Pictures
Flash Off
The flash will not discharge.
Flash On
The flash discharges.
Auto flash + Red-eye
Reduction
This mode reduces the phenomenon of red eyes caused
by the light from the flash being reflected in the subject’s
eyes. The flash discharges automatically.
Flash On + Red-eye Reduction This mode reduces the phenomenon of red eyes
caused by the light from the flash being reflected in the
subject’s eyes. The flash will discharge regardless of
lighting conditions.
memo
• The [Auto flash] and [Auto flash + Red-eye Reduction] modes
cannot be selected when the Capture mode is set to
.
• The flash is off when the Capture mode is set to
,
continuous shooting, infinity-landscape, fireworks in picture
mode or super macro mode.
• The flash discharges once before the main flash as supplementary light for AE metering.
• In [Auto flash + Red-eye Reduction] and [Flash On + Red-eye
Reduction] modes, the flash discharges once to make the
pupils of the subject’s eyes smaller shortly before the main
flash discharges to take the picture.
z
42
The flash discharges automatically depending on the
light conditions.
Press the
button in Capture mode.
The flash mode changes each time the button is pressed
and the icon is displayed on the LCD monitor.
The camera is ready to take the picture in the set flash mode.
Status of the Focus Status Lamp and Flash Status Lamp
☞ p.25
Saving the Flash Mode ☞ p.87
e04_kb338_038_088_41e.qk 3/17/03 5:23 PM Page 43
Rec. Mode
Recorded Pixels
Quality Level
White Balance
Focusing Area
AE Metering
Sensitivity
x
c
1/3
MENU
2592 1944
AWB
Wide
Auto
Exit
Ok
OK
z
Selecting the Recorded Pixels
You can choose the number of recorded pixels from [2592 ×
1944], [2048 × 1536], [1600 × 1200], [1024 × 768] and [640 ×
480].
c
Select [Recorded Pixels] on the [
Use the four-way controller ()
to change the size.
Press the OK button.
The camera is ready to take the
picture.
Rec.Mode] menu.
Rec. Mode
Recorded Pixels
Quality Level
White Balance
Focusing Area
AE Metering
Sensitivity
1/3
memo
MENU
Exit
2592 1944
AWB
Wide
Auto
OK
Ok
Taking Pictures
z
x
• The recorded pixels is fixed at 320 × 240 pixels in the movie
picture mode.
• If you select a large size, the picture may appear distinct
when it is printed out.
• Selecting a small size reduces the volume of data. This is
useful for attaching images to E-mail or posting them on a
website.
43
e04_kb338_038_088_41e.qk 3/17/03 5:23 PM Page 44
Rec. Mode
Recorded Pixels
Quality Level
White Balance
Focusing Area
AE Metering
Sensitivity
x
c
1/3
MENU
2592 1944
AWB
Wide
Auto
Exit
OK
Ok
z
Selecting the Quality Levels
You can choose the image compression rate.
TIFF
Taking Pictures
z
x
c
TIFF
The image is recorded as uncompressed data.
BEST
The quality is better and there is a high volume of
image data.
BETTER
Standard level
GOOD
The quality is good and there is a low volume of
image data.
Select [Quality Level] on the [
Use the four-way controller ()
to change the image quality.
Press the OK button.
The camera is ready to take the
picture.
Rec.Mode] menu.
Rec. Mode
Recorded Pixels
Quality Level
White Balance
Focusing Area
AE Metering
Sensitivity
1/3
memo
44
MENU
Exit
2592 1944
AWB
Wide
Auto
OK
Ok
• If you selected TIFF, the recorded pixels is fixed at 2592 ×
1944.
• If you select TIFF when the recorded pixels has been set to
other than [2592 × 1944], the size is automatically changed to
[2592 × 1944].
• 3D image mode, multiple exposure mode and auto bracket
mode are not available when TIFF is selected.
e04_kb338_038_088_41e.qk 3/17/03 5:23 PM Page 45
Rec. Mode
Recorded Pixels
Quality Level
White Balance
Focusing Area
AE Metering
Sensitivity
xc
v
1/3
MENU
2592 1944
AWB
Wide
Auto
Exit
OK
Ok
z
Adjusting the Color Balance according to Lighting (White Balance)
You can take pictures in natural colors by adjusting the white
balance according to the light conditions at the time of shooting.
The camera adjusts the white balance automatically.
Daylight
Use this mode when taking pictures outside in sunlight.
Shade
Tungsten
Light
Use this mode when taking pictures outside in the shade.
Fluorescent
Light
Use this mode when taking pictures under fluorescent light.
Choose the type of fluorescent light from W (white (4200°K)*),
N (neutral white (5000°K)*) and D (daylight (6500°K)*).
Use this mode when taking pictures under electric or
other tungsten light.
Manual
Use this mode when taking pictures by adjusting the
white balance manually.
*The color temperature (°K) is approximate and does not indicate the precise
color.
z
x
c
v
Select [White Balance] on the [
Press the four-way controller ().
The white balance screen will be
displayed.
Taking Pictures
Automatic
Rec.Mode] menu.
White Balance
AWB
Use the four-way controller ()
to select the setting.
-D
MENU
Exit
OK
Ok
Press the OK button twice.
The camera is ready to take the picture.
Saving the White Balance ☞ p.87
45
e04_kb338_038_088_41e.qk 3/17/03 5:23 PM Page 46
Selecting the Type of Fluorescent Light
z
x
c
Select [
screen.
] on the White Balance
White Balance
AWB
Use the four-way controller () to
choose “W”, “N” or “D”.
Press the OK button twice.
The camera is ready to take the
picture.
D
MENU
Exit
OK
Ok
OK
Ok
Manual Setting
z
x
Taking Pictures
46
c
v
Select [ ] (manual) on the white
balance screen.
White Balance
AWB
Point your camera at a blank sheet
of paper so that it fills the screen.
Press the Display button.
The white balance is automatically
adjusted, [Complete] is displayed
on the LCD monitor and the display
returns to the menu screen.
-D
1/3
Press the OK button.
The camera is ready to take the picture.
MENU
Exit
DISP
Adjust
e04_kb338_038_088_41e.qk 3/17/03 5:23 PM Page 47
Rec. Mode
Recorded Pixels
Quality Level
White Balance
Focusing Area
AE Metering
Sensitivity
x
c
1/3
MENU
2592 1944
AWB
Wide
Auto
Exit
Ok
OK
z
Changing the AF Area (Focusing Area)
You can change the angle of the autofocus area.
Wide
Spot
x
c
Select [Focusing Area] on the
[
Rec.Mode] menu.
Use the four-way controller ()
to change the setting.
Press the OK button.
The camera is ready to take the
picture.
Rec. Mode
Recorded Pixels
Quality Level
White Balance
Focusing Area
AE Metering
Sensitivity
1/3
MENU
Exit
2592 1944
AWB
Wide
Auto
OK
Ok
Taking Pictures
z
Normal range
The autofocus range becomes smaller.
The AF area does not appear in the viewfinder. Always check
memo the focusing area on the LCD monitor.
47
e04_kb338_038_088_41e.qk 3/17/03 5:23 PM Page 48
Rec. Mode
Recorded Pixels
Quality Level
White Balance
Focusing Area
AE Metering
Sensitivity
x
c
1/3
MENU
2592 1944
AWB
Wide
Auto
Exit
OK
Ok
z
Setting the Light Metering Range to Determine the Exposure (AE Metering)
You can choose which part of the screen to use to measure the
brightness and determine the exposure.
Taking Pictures
z
x
c
Multi segment
Center-weighted
The exposure is determined by the entire screen.
The exposure is determined mainly by the center of the screen.
Spot
The exposure is determined by the small area in the center of
the screen only.
Select [AE Metering] on the
[
Rec.Mode] menu.
Rec. Mode
Recorded Pixels
Quality Level
White Balance
Focusing Area
AE Metering
Sensitivity
Use the four-way controller ()
to change the metering mode.
Press the OK button.
The camera is ready to take the
picture.
1/3
Saving the AE Metering Method ☞ p.87
48
MENU
Exit
2592 1944
AWB
Wide
Auto
OK
Ok
e04_kb338_038_088_41e.qk 3/17/03 5:23 PM Page 49
Rec. Mode
Recorded Pixels
Quality Level
White Balance
Focusing Area
AE Metering
Sensitivity
x
c
1/3
MENU
2592 1944
AWB
Wide
Auto
Exit
OK
Ok
z
Setting the Sensitivity
You can select the Sensitivity to suit the brightness of the surroundings.
Sensitivity
Auto
100
200
400
z
x
c
The camera sets the speed automatically.
• As the lower Sensitivity produces sharp images with little or
no noise, but the shutter speed will be slower in low light conditions.
• As the higher Sensitivity uses faster shutter speed in low light
conditions to reduce camera shake.
Select [Sensitivity] on the [
Rec.Mode] menu.
Use the four-way controller ()
to change the Sensitivity.
Press the OK button.
The camera is ready to take the
picture.
Rec. Mode
Recorded Pixels
Quality Level
White Balance
Focusing Area
AE Metering
Sensitivity
1/3
memo
Taking Pictures
64
MENU
Exit
2592 1944
AWB
Wide
Auto
OK
Ok
[Auto] cannot be selected in manual exposure mode.
Saving the Sensitivity ☞ p.87
49
e04_kb338_038_088_41e.qk 3/17/03 5:23 PM Page 50
Rec. Mode
Recorded Pixels
Quality Level
White Balance
Focusing Area
AE Metering
Sensitivity
x
c
1/3
MENU
2592 1944
AWB
Wide
Auto
Exit
OK
Ok
z
Setting the Instant Review time (Instant Review)
You can choose the Instant Review time from 0.5sec., 1sec.,
2sec., 3sec., 4sec., 5sec. or OFF (no display).
Taking Pictures
50
z
x
c
Select [Instant Review] on the [
Use the four-way controller ()
to change the display time.
Press the OK button.
The camera is ready to take the
picture.
Rec.Mode] menu.
Rec. Mode
Auto Bracket
Digital Zoom
Instant Review
Interval Shoot
Fast Fwd Movie
3D Mode
2/3
MENU
Exit
On
2sec
Off
Parallel
OK
Ok
e04_kb338_038_088_41e.qk 3/17/03 5:23 PM Page 51
Rec. Mode
Recorded Pixels
Quality Level
White Balance
Focusing Area
AE Metering
Sensitivity
x
c
1/3
MENU
2592 1944
Exit
AWB
Wide
Auto
OK
Ok
z
Setting the Image Sharpness (Sharpness)
You can choose whether you want the image to have sharp or
soft outlines.
c
Select [Sharpness] on the [
Rec.Mode] menu.
Use the four-way controller ()
to change the setting from
[Normal] to [Hard (+)] or [Soft (–)].
Press the OK button.
The camera is ready to take the
picture.
Rec. Mode
Memory
Sharpness
Saturation
Contrast
USER
3/3
MENU
Exit
OK
Ok
Taking Pictures
z
x
51
e04_kb338_038_088_41e.qk 3/17/03 5:23 PM Page 52
Rec. Mode
Recorded Pixels
Quality Level
White Balance
Focusing Area
AE Metering
Sensitivity
x
c
1/3
MENU
2592 1944
Exit
AWB
Wide
Auto
OK
Ok
z
Setting the Color Saturation (Saturation)
You can set the color saturation.
z
x
Taking Pictures
52
c
Select [Saturation] on the [
Rec.Mode] menu.
Use the four-way controller ()
to change the setting from
[Normal] to [Hard (+)] or [Soft (–)].
Press the OK button.
The camera is ready to take the
picture.
Rec. Mode
Memory
Sharpness
Saturation
Contrast
USER
3/3
MENU
Exit
OK
Ok
e04_kb338_038_088_41e.qk 3/17/03 5:23 PM Page 53
Rec. Mode
Recorded Pixels
Quality Level
White Balance
Focusing Area
AE Metering
Sensitivity
x
c
1/3
MENU
Exit
2592 1944
AWB
Wide
Auto
OK
Ok
z
Setting the Image Contrast (Contrast)
You can set the image contrast.
z
x
Rec.Mode] menu.
Use the four-way controller ()
to change the setting from
[Normal] to [Hard (+)] or [Soft (–)].
Press the OK button.
The camera is ready to take the
picture.
Rec. Mode
Memory
Sharpness
Saturation
Contrast
USER
3/3
MENU
Exit
OK
Ok
Taking Pictures
c
Select [Contrast] on the [
53
e04_kb338_038_088_41e.qk 3/17/03 5:23 PM Page 54
Taking Pictures
z
x
Letting the Camera Set the Exposure (Program Mode)
Taking Pictures
The camera automatically sets the shutter speed and aperture
for taking still pictures. However, you can select other functions
such as the flash mode or continuous shooting mode.
z
x
Set the mode dial to
.
200
Press the shutter release button.
The picture will be taken.
1/250
F2.8
02/20/2003
11:19
Aperture Shutter speed
Using the Shutter Release Button ☞ p.25
Playing back images ☞ p.26
54
e04_kb338_038_088_41e.qk 3/17/03 5:23 PM Page 55
z
c
x
Setting the Aperture Value (Aperture Priority Mode)
z
x
c
Set the mode dial to
.
Use the four-way controller () to
change the aperture value.
Makes the aperture larger.
(Reduces the aperture value.)
1/250
F2.8
Makes the aperture smaller.
(Increases the aperture value.)
Aperture value
02/20/2003
11:19
Taking Pictures
In this mode the aperture value is set manually and the camera
automatically sets the shutter speed.
Press the shutter release button.
The picture will be taken.
Playing Back Still Pictures ☞ p.26
The aperture value will be saved when the camera is turned off.
memo
Caution
• When the focus mode is set to manual, the four-way controller () becomes the manual focus button and cannot
be used to change the aperture value. To change the aperture value, press the OK button once and then use the fourway controller () to change the value.
• The exposure is not appropriate when the shutter speed is
displayed in orange on the LCD monitor.
55
e04_kb338_038_088_41e.qk 3/17/03 5:23 PM Page 56
z
c
x
Setting the Shutter Speed (Shutter Priority Mode)
In this mode the shutter speed is set manually and the camera
automatically sets the aperture value.
Taking Pictures
z
x
c
Set the mode dial to
.
Use the four-way controller () to
change the shutter speed.
Increases the shutter speed.
Reduces the shutter speed.
Press the shutter release button.
The picture will be taken.
1/250
F2.8
02/20/2003
11:19
Shutter speed
Playing Back Still Pictures ☞ p.26
The set shutter speed will be saved when the camera is turned
memo off.
Caution
56
• When the focus mode is set to manual, the four-way controller () becomes the manual focus button and cannot
be used to change the shutter speed. To change the shutter
speed, press the OK button once and then use the four-way
controller () to change the value.
• The exposure is not appropriate when the aperture value is
displayed in orange on the LCD monitor.
e04_kb338_038_088_41e.qk 3/17/03 5:23 PM Page 57
z
c
x
Setting the Exposure Manually (Manual Exposure Mode)
You can set the shutter speed and aperture value manually.
Set the mode dial to
.
Use the four-way controller to
change the shutter speed and
aperture value.
Increases the shutter speed.
Reduces the shutter speed.
Makes the aperture larger.
(Reduces the aperture value.)
Makes the aperture smaller.
(Increases the aperture value.)
198
1/250
F2.8
Aperture
02/20/2003
11:19
Taking Pictures
z
x
Shutter speed
If the combination of shutter speed and aperture value do
not give an appropriate exposure, a warning will be displayed.
(Lit)
If the deviation from the appropriate exposure is between
–0.3 EV and –2.0 EV,
will light, and if between +0.3 EV
and +2.0 EV
will light, and the value will be displayed.
(Blinking)
If the picture is underexposed at a setting lower than –2.0 EV,
blinks, and if overexposed at a setting higher than +2.0 EV,
blinks.
(Lit)
Metering is not possible.
57
e04_kb338_038_088_41e.qk 3/17/03 5:23 PM Page 58
c
Press the shutter release button.
The picture will be taken at the set shutter speed and aperture value.
Playing Back Still Pictures ☞ p.26
memo
Caution
Taking Pictures
58
The shutter speed and aperture value will be saved when the
camera is turned off.
• EV compensation is not available in this mode.
• When the focus mode is set to manual, the four-way controller () becomes the manual focus button and cannot
be used to change the aperture value. To change the aperture value, press the OK button once and then use the fourway controller () to change the value.
• The [Auto flash] and [Auto flash + Red-eye Reduction] flash
modes cannot be selected.
e04_kb338_038_088_41e.qk 3/17/03 5:23 PM Page 59
z
c
x
Selecting the Picture Mode According to the Shooting
Scene (Picture mode)
You can select the Picture mode according to the shooting scene.
Picture mode
There are nine available modes in Picture mode.
Night-Scene Enables you to take dark scenes such as night views.
Mode
z
x
c
Flower
Enables to take flower photos bright in color.
Portrait
Enables to take portraits with spatial effect, by emphasizing the person.
Surf &
Snow
Enables to take clear photos at dazzling places like beaches and snow covered mountains.
Autumn
Colors
Enables you to take colorful photos of trees in autumn.
Sunset
Enables to reproduce beautiful colors for sunrise and
sunset photos.
Fireworks
Enables you to take bright photos of fireworks.
Text
Enables you to take clear photos of text.
Set the Mode dial to
.
Press the four-way controller
() to select the required mode.
Press the shutter release button.
The picture will be taken.
Taking Pictures
Landscape Enables to take landscape photos with bright colors.
200
02/20/2003
11:19
Playing Back Still Pictures ☞ p.26
59
e04_kb338_038_088_41e.qk 3/17/03 5:23 PM Page 60
memo • The picture mode will be saved when the camera is turned
off.
• The flash is disabled in Fireworks mode and the focus is fixed
at infinity.
Caution
• When the focus mode is set to manual, the four-way controller () becomes the manual focus button and cannot be used to change the picture mode. To change the
picture mode, press the OK button once and then use the
four-way controller () to change the mode.
• To avoid camera movement in Night-scene, Sunset and
Fireworks mode, you are recommended to fix the camera
on a tripod.
Taking Pictures
60
e04_kb338_038_088_41e.qk 3/17/03 5:23 PM Page 61
z
xc
Taking Movie Pictures (Movie Picture Mode)
This mode enables you to take moving images. The maximum
length of one motion picture is approximately 10 minutes. Sound
can be recorded at the same time.
x
Set the mode dial to
.
The following information will be
displayed on the LCD monitor.
1
Flash OFF
Movie Picture mode icon
Remaining shooting time
Remaining number of sets
2
34
5
•12SEC
02/20/2003
11:19
Taking Pictures
z
Press the shutter release button.
Shooting will start.
You can change the size of the image using the Zoom button.
: makes the image bigger.
: makes the image smaller.
c
Press the shutter release button.
Shooting will end.
The remaining shooting time will be displayed.
61
e04_kb338_038_088_41e.qk 3/17/03 5:23 PM Page 62
Keeping the shutter release button pressed
If you keep the shutter release button pressed for more than
one second, pictures will be taken for as long as you keep the
button pressed. Shooting stops when you take a finger off from
the shutter release button.
Playing Back Movie Pictures ☞ p.91
Caution
Taking Pictures
62
• The flash will not discharge in Movie Picture mode.
• Continuous shooting, interval shooting and multiple exposure shooting are not possible in Movie Picture mode.
• The LCD monitor cannot be turned off in Movie Picture
mode.
• Focusing Area mode is not available in Movie Picture
mode.
• When shooting in Movie Picture mode, only the digital
zoom can be operated.
e04_kb338_038_088_41e.qk 3/17/03 5:23 PM Page 63
z
cv
x
b
Taking Panorama Pictures (Panorama Assist Mode)
The ACD photostitcher is only for the English version and the
Japanese version.
You can take a number of images and join them together to
form a panorama picture. The panorama software (ACD photostitcher) provided with the camera is necessary for joining the
images.
Set the mode dial to
.
Use the four-way controller to
choose the direction in which the
images will be joined.
Joins the images at the left.
Joins the images at the right.
Joins the images at the top.
Joins the images at the bottom.
Set shift direction
Taking Pictures
z
x
The example shows the images
when is selected.
c
v
Take the first picture.
Press the shutter release button to
take the first image. The right edge
of the image is displayed in transparent form on the left of the LCD monitor.
Move the camera to the right and
take the second picture.
Repeat the above procedure to take
the third and subsequent pictures.
02/20/2003
11:19
02/20/2003
11:19
63
e04_kb338_038_088_41e.qk 3/17/03 5:23 PM Page 64
b
memo
Caution
Taking Pictures
64
Press the OK button.
The screen returns to Step z.
To cancel Panorama assist mode, change to another mode.
• The camera cannot join the images. Use the panorama
software (ACD photostitcher) provided with the camera.
• Continuous shooting, Multiple Exposure mode and interval shooting are not possible in Panorama assist mode.
• A computer running Windows is necessary for joining
images. (The ACD photostitcher software provided with
the camera is not supported by Macintosh.)
e04_kb338_038_088_41e.qk 3/17/03 5:23 PM Page 65
b
n,
xc
z
v.
Taking Stereo Pictures (3D Image Mode)
You can take 3D pictures using the LCD monitor and view them
by the parallel method or cross method (p.67). If you print out
the 3D pictures and look at them through the 3D image viewer
provided, the image will appear in three dimensions.
Taking Pictures
Select the 3D mode
The default setting is [Parallel]. If you do not need to switch to
[Cross], go to Step b.
z
x
c
v
Press the Menu/Fn button.
The [
Rec. Mode] menu will be displayed.
Press the four-way controller ()
to select [3D Mode].
Rec. Mode
Auto Bracket
Digital Zoom
Instant Review
Interval Shoot
Fast Fwd Movie
3D Mode
Use the four-way controller ()
to select [Parallel] or [Cross].
To view the picture with the 3D image
2/3 MENU Exit
viewer,
select [Parallel].
You can also view it without the image viewer.
On
2sec
Off
Cross
OK
Ok
Press the OK button.
The 3D image mode screen appears again.
65
e04_kb338_038_088_41e.qk 3/17/03 5:23 PM Page 66
Taking pictures
b
n
Set the Mode dial to
.
The screen for taking the first picture appears in the middle
of the LCD monitor.
Take the first picture.
14
Hold the camera so that the subject
is in the middle of the screen, and
press the shutter release button.
02/20/2003
11:19
m
,
Taking Pictures
.
memo
66
The picture is displayed in the left
half screen of the LCD monitor. The
right half screen is for taking the
second picture.
Move the camera to right without
changing your stance.
14
Take the second picture.
Make sure that the subject is in the middle of the right half
of the screen and press the shutter release button.
When you have taken the second picture, the screen
returns to Step n.
Press the Playback button.
The LCD monitor displays both the left and right images.
• The 3D image mode is not available when TIFF is selected
for the image quality.
• To cancel the 3D image mode, press the Menu/Fn button or
change the 3D image mode to another Capture mode.
• A clear three-dimensional effect will not be achieved if the two
images are taken in widely different positions (heights) or are
not straight. When taking a person, you are recommended to
ask your model to stay as still as possible and to take the
second picture as quickly as you can. It is easier to take the
pictures if you use a tripod or appropriate base.
• As a guide, the camera should be moved about 1/40 of the
distance between the camera and the subject. For example, if
the subject is 3m away, the distance the camera should be
moved will be 3m÷40=7.5cm.
However, as the way people see three-dimensional images
differs from person to person, there is no need to be too concerned. Refer to the table below for a simple guide to how far
to move the camera.
Distance to subject
0.1 m
0.3 m
0.5 m
1m
3m
5m
Camera movement
0.5 cm
1 cm
1.5 cm
2.5 cm
7.5 cm
13 cm
e04_kb338_038_088_41e.qk 3/17/03 5:23 PM Page 67
Viewing 3D pictures by the parallel method and cross
method
As our eyes are positioned about 6 – 7 cm apart, there is a very
slight deviation between what we see with our right eye and
what we see with our left eye. The difference is processed by
our brain to produce a three-dimensional image. This principle is
applied to taking and viewing 3D pictures.
3D pictures can be viewed by the parallel method where the left
and right lines of vision are virtually parallel, as when looking at
a distant scene, or the cross method where the left and right
lines of vision are crossed, as when you cross your eyes. A certain amount of practice may be necessary to view 3D pictures
without using the viewer.
How to Assemble the 3D Image Viewer
Assemble the 3D image viewer supplied with the camera as
shown below.
Taking Pictures
67
e04_kb338_038_088_41e.qk 3/17/03 5:23 PM Page 68
How to view 3D pictures using the 3D image viewer
Print out the pictures so that they are about 11cm or 12cm wide
and place the divider of the 3D image viewer in the middle of
the two.
As the distance between the left and right eyes differs from per-
Taking Pictures
memo son to person, some people may have difficulty obtaining a
three-dimensional effect even when looking at prints that are the
same size. It may be especially difficult if the pictures are very
large or very small. Try different sizes until the right effect is
achieved.
Caution
68
• Never look at the sun through the 3D image viewer.
• Do not leave the 3D image viewer where it is exposed to
direct sunlight as this may lead to fire.
e04_kb338_038_088_41e.qk 3/17/03 5:23 PM Page 69
Example of a 3D picture
Taking Pictures
69
e04_kb338_038_088_41e.qk 3/17/03 5:23 PM Page 70
z
c
x
Taking Pictures with Digital Filters (Digital Filter Mode)
You can take pictures using digital filters. The filters consist of
color filters such as red, blue and green, a soft filter that produces a fuzzy effect.
Taking Pictures
● Color filters
Eight colors, black-and-white, sepia, red, pink, violet, blue, green
and yellow, are provided for the color filters. When you select a
color filter in the Digital Filter mode, the display on the LCD monitor
is filtered with the selected color, and the pictures are taken in that
color.
● Soft Filter
Pictures taken with the soft filter have a fuzzy effect.
70
e04_kb338_038_088_41e.qk 3/17/03 5:23 PM Page 71
z
x
c
Set the Mode dial to
.
Use the four-way controller () to select a digital filter
you want to use.
Press the shutter release button.
The picture will be taken.
Playing back still pictures ☞ p.26
Caution
When the focus mode is set to manual, the four-way controller () becomes the manual focus button and cannot be
used to change the filter. To change the filter, press the OK
button once and then use the four-way controller () to
change the filter.
Taking Pictures
71
e04_kb338_038_088_41e.qk 3/17/03 5:23 PM Page 72
z
x
Using Preset Function Settings (User Mode)
By setting the mode dial to
, the preset shooting mode and
functions are activated, enabling you to take pictures immediately with your own camera settings.
Taking Pictures
z Set the mode dial to
.
1/250
F2.8
x Press the shutter release button.
The picture will be taken.
Registering Functions in User Mode ☞ p.88
Playing back images ☞ p.26
72
02/20/2003
11:19
e04_kb338_038_088_41e.qk 3/17/03 5:23 PM Page 73
z
xc
Recording Sound (Voice Recording Mode)
You can record sound. The recordable time is displayed on the
LCD monitor according to how much space is available on the
SD Memory Card/MultiMediaCard.
.
The recordable time is displayed on
the LCD monitor.
Remaining time
Recording time
x Press the shutter release button.
Recording starts. The self-timer lamp
and flash status lamp blink during
recording.
2 1
0 : 29 : 55
00 : 00
Start
02/20/2003
11:19
Taking Pictures
z Set the mode dial to
c Press the shutter release button.
Recording stops. The remaining recordable time is displayed.
Playing back sound ☞ p.92
memo
Sound is saved in WAVE monaural files.
73
e04_kb338_038_088_41e.qk 3/17/03 5:23 PM Page 74
z
Using the Zoom
You can use the zoom to take pictures in tele or wide mode.
z
Press the Zoom button in Capture
mode.
198
Taking Pictures
(Wide): makes the subject larger
(Tele): makes the subject smaller
When the digital zoom function is
disabled, you can take pictures at
up to 5× magnification using the
optical zoom.
When the digital zoom is enabled,
you can further enlarge the subject
to a maximum magnification equivalent to 20×.
Zoom bar Digital
zoom range
198
Digital Zoom
Saving the Zoom Position ☞ p.87
74
e04_kb338_038_088_41e.qk 3/17/03 5:23 PM Page 75
Enabling the Digital Zoom Function
z
x
c
v
Press the Menu button in Capture mode.
The [
Rec.Mode] menu will be displayed.
Press the four-way controller ()
to select [Digital Zoom].
Use the four-way controller () to
select [On].
Press the OK button.
The camera is ready to take a picture.
Rec. Mode
Auto Bracket
Digital Zoom
Instant Review
Interval Shoot
Fast Fwd Movie
3D Mode
2/3
MENU
Exit
On
2sec
Off
Parallel
OK
Ok
Saving the Digital Zoom Function Setting ☞ p.87
Caution
Taking Pictures
• When you turn the LCD monitor off, the digital zoom is disabled even if the digital zoom function is set to On.
• When shooting an image using the digital zoom function,
the image will be blurred.
• When using the digital zoom function, the camera movement may occur due to high magnification. Use the tripod to
prevent it.
75
e04_kb338_038_088_41e.qk 3/17/03 5:23 PM Page 76
z
EV Compensation
You can take pictures that are intentionally over exposed or
under exposed.
z
Taking Pictures
Press the four-way controller ()
in Capture mode.
Four-way controller ()
decreases the EV compensation to a negative (–) level
Four-way controller ()
increases the EV compensation to a positive (+) level
198
1/250
F2.8
–1.0
02/20/2003
11:19
EV compensation level
The set level is displayed on the LCD monitor.
Saving the EV Compensation ☞ p.87
memo
76
• If you press or one time, or set to ± 0, the set level displayed on the LCD monitor will go off after two seconds.
e04_kb338_038_088_41e.qk 3/17/03 5:23 PM Page 77
z
x
Using the Self-Timer
The picture will be taken 10 seconds after the shutter release
button is pressed.
z
Press the shutter release button.
The self-timer is engaged and the self-timer lamp lights. The
picture is taken approximately three seconds after the selftimer lamp starts to blink.
Playing Back Images and Sound ☞ p.89
memo
Taking Pictures
x
Press the
button in Capture mode to display
on the LCD monitor.
• If you turn the LCD monitor on, the second count will be displayed.
• To cancel the self-timer, press the shutter release button
halfway while the second count is displayed.
77
e04_kb338_038_088_41e.qk 3/17/03 5:23 PM Page 78
z
Using the Remote Control Unit (optional)
You can take pictures using the remote control F (optional).
z
Taking Pictures
x
Press the
button in Capture
mode to display
on the LCD
monitor.
The self-timer lamp will blink and the
camera is ready to take pictures.
198
1/250
02/20/2003
11:19
F2.8
Press the shutter release button on
the remote control unit.
The self-timer lamp will blink rapidly and the picture will be
taken after approximately three seconds.
Playing Back Images and Sound
☞ p.89
• The buttons on the camera can be used in the same way.
memo • Please ensure that the remote control unit is no more than 5
meters away from the front of the camera.
• When taking pictures against the light, the distance at which the
remote control unit operates may be reduced.
• To take a picture immediately after pressing the shutter release
button on the remote control unit, press the
button in
step z to display
on the LCD monitor.
Life of the Battery for the Remote Control Unit
A signal can be sent from the remote control unit to the camera
approximately 30,000 times. If the battery needs changing, contact your nearest Pentax customer service center. (A charge is
made for replacing the battery.)
78
e04_kb338_038_088_41e.qk 3/17/03 5:23 PM Page 79
z
x
Continuous Shooting
Pictures are taken continuously while the shutter release button is
pressed.
z
198
1/250
F2.8
02/20/2003
11:19
Press the shutter release button.
Pictures will be taken continuously while the shutter release
button is pressed. Shooting stops when you take a finger off
from the shutter release button.
Playing Back Still Pictures
Taking Pictures
x
Press the
button in Capture
mode to display
on the LCD
monitor.
The mode will change to Continuous
Shooting mode.
☞ p.26
The interval will vary according to the [Recorded Pixels] and
memo [Quality Level] setting.
Caution
• The flash will not discharge in Continuous Shooting mode.
• Continuous shooting is not available for Movie Picture,
Panorama assist mode and 3D Image modes.
79
e04_kb338_038_088_41e.qk 3/17/03 5:23 PM Page 80
z
x
Taking Pictures at Fixed Intervals (Interval Shooting)
In this mode still pictures are taken automatically at a fixed interval.
z
Taking Pictures
x
Press the
button in Capture mode to display
on the LCD monitor.
Press the shutter release button.
Interval shooting will start with the following settings.
• Interval
0min 10sec
• Number of shot 02
• Start time
0hr 0min
When shooting is finished, the camera turns off automatically.
Setting the interval, number of shot, and start time
z
x
c
Press the Menu/Fn button in Capture mode.
The [
Rec.Mode] menu will be displayed.
Press the four-way controller () to select [Interval
Shoot].
Press the four-way controller ().
The Interval Shooting menu will be
displayed and [Interval] will be
framed.
Interval Shoot
Interval
1min 10sec
Number of Shot
02
Start Time
0hr 0min
MENU
80
Exit
OK
Ok
e04_kb338_038_088_41e.qk 3/17/03 5:23 PM Page 81
v
b
n
Use the four-way controller () to select the number of
pictures, then press ().
The frame will move to [Start Time].
Set the time to start shooting.
1. Press the four-way controller ().
will be displayed above and below the hours.
2. Use the four-way controller () to change the hours,
then press .
will be displayed above and below the minutes.
3. Use the four-way controller () to change the minutes, then press .
Press the OK button twice.
Playing Back Still Pictures ☞ p.26
memo
Caution
Taking Pictures
m
Set the interval time.
1. Press the four-way controller ().
will be displayed above and below the minutes.
2. Use the four-way controller () to change the minutes, then press ().
will be displayed above and below the seconds.
3. Use the four-way controller () to change the seconds, then press ().
4. Press the four-way controller ().
The frame will move to [Number of shoot].
• Interval shooting can be set at intervals of 10 seconds to 4 minutes
in units of 1 second, and intervals of 4 minutes to 99 minutes in
units of 1 minute. Intervals of less than 10 seconds cannot be set.
• The number of pictures can be set in the range of 2 to 99 pictures.
• The start time can be set between 0 min. and 23 hr. 59 min.
in units of 1 minute.
• If the start time is set to 0 min., the first picture will be taken
as soon as the shutter release button is pressed.
• If you press the power switch on during standby, the remaining number of pictures and interval time will be displayed on
the LCD monitor. If you press the Menu/Fn button, the message “Stop interval shooting?” will be displayed. To cancel
interval shooting, press the OK button.
• If the SD Memory Card/MultiMediaCard runs out of memory space,
interval shooting stops and the camera turns off automatically.
Interval shooting is not possible in
mode.
81
e04_kb338_038_088_41e.qk 3/17/03 5:23 PM Page 82
zz
vc
xc
x
Superimposing One Picture on Top of Another (Multiple Exposure Mode)
You can superimpose a new image on top of an image already
recorded.
When images have been recorded
z
Taking Pictures
x
c
v
82
Press
in Capture mode to
switch to Multiple Exposure
mode.
The screen for selecting the base
image will be displayed.
Use the four-way controller ()
to choose the base image and
press the OK button.
The selected image will appear in
transparent form on the LCD monitor.
100-0038
Choose Base Image
MENU
Exit
OK
Ok
Aim the camera at your subject
198
and choose the exposure method
with the four-way controller ().
Priority is given to the brighter
image.
1/250
02/20/2003
11:19
F2.8
Priority is given to the darker
image.
Exposure method
The average exposure is obtained.
Press the shutter release button.
The Instant Review screen will be displayed and you will be
asked whether you want to continue shooting.
If you select [Continue] and press the OK button, the picture
you have just created will be played back enabling you to
add another image. The combined picture will be saved as
a new file.
e04_kb338_038_088_41e.qk 3/17/03 5:23 PM Page 83
When there are no recorded images
z
x
Aim the camera at your subject
and choose the exposure method
with the four-way controller ().
Priority is given to the brighter
image.
Priority is given to the darker
image.
The average exposure is
obtained.
Base Image Shooting
198
1/250
F2.8
02/20/2003
11:19
Exposure method
Press the shutter release button.
The Instant Review screen will be displayed and you will be
asked whether you want to continue shooting.
If you select [Continue] and press the OK button, the picture
you have just created will be played back enabling you to
add another image. The combined picture will be saved as
a new file.
Taking Pictures
c
Press
in Capture mode to
switch to Multiple Exposure
mode.
A message will appear on the LCD
monitor informing you that the camera is ready to take the base
image.
Take the base image. When you
have taken the base image, it will
appear in transparent form on the
LCD monitor.
Playing Back Still Pictures ☞ p.26
Caution
• Multiple exposure is not possible in Movie Picture mode,
Panorama assist mode or 3D mode.
• Continuous shooting is not possible in Multiple Exposure
mode.
• The LCD monitor cannot be turned off in Multiple Exposure
mode.
83
e04_kb338_038_088_41e.qk 3/17/03 5:23 PM Page 84
,
xcvbn
m
z
Rec. Mode
Recorded Pixels
Quality Level
White Balance
Focusing Area
AE Metering
Sensitivity
1/3
MENU
Exit
2592 1944
AWB
Wide
Auto
OK
Ok
Automatically Changing the Shooting Conditions (Auto bracket)
You can take pictures automatically with three different exposure, white balance, sharpness, saturation and contrast settings.
z
Taking Pictures
Press the Menu/Fn button in Capture mode.
The [
Rec. Mode] menu will be displayed.
x
c
Press the four-way controller () to select [Auto Bracket].
v
Use the four-way controller ()
to select the conditions for bracket shooting.
If you selected [Sharpness],
[Saturation] or [Contrast], skip to
step m.
Press the four-way controller ().
[Applied Photo] screen to select the bracket setting will be
displayed.
Auto Bracket
Applied Photo
Bracket Amount
MENU
b
n
Press the four-way controller ()
to select [Exp. Bracket] or [White
Balance].
Go to [Bracket Amount].
OK
Ok
Auto Bracket
Applied Photo
Bracket Amount
Exp.Bracket
± 0.3
Use the four-way controller ()
to set the bracketing steps.
MENU
84
Exit
Exp.Bracket
± 0.3
Exit
OK
Ok
e04_kb338_038_088_41e.qk 3/17/03 5:23 PM Page 85
m
,
Press the OK button.
The Bracket mode is set.
Press and hold down the shutter release button.
Auto bracket shooting starts.
When shooting is finished, a message will be displayed
asking whether you want to continue shooting or not. To
continue shooting in auto bracket mode, select [Continue]
and press the OK button.
Playing Back Still Pictures ☞ p.26
• Check the pictures you have taken using the Playback mode.
memo • If you set auto bracket when you set the Continuous shooting
Taking Pictures
mode, continuous shooting will be canceled.
• The auto bracket setting will be canceled by pressing the
Menu/Fn button or OK button.
• Auto bracket mode is not available when TIFF is selected for
the image quality.
85
e04_kb338_038_088_41e.qk 3/17/03 5:23 PM Page 86
bn
xc
v
z
Taking Fast Forward Movie Pictures (Fast Fwd Movie)
This mode lets you take movie pictures at a delayed frame rate
so that when you play the movie back, the action appears
speeded up.
z
Taking Pictures
x
c
v
b
n
Press the Menu/Fn button in Capture mode.
The [
Rec.Mode] menu will be displayed.
Press the four-way controller () to select [Fast Fwd
Movie].
Use the four-way controller ()
Rec Mode
Auto Bracket
to choose [Off (×1)], [×2], [×5],
Digital Zoom
On
[×10], [×50] or [×100].
Instant Review
2sec
Interval Shoot
Press the OK button.
Fast Fwd Movie
x2
3D Mode
Parallel
Press the shutter release button.
OK
2/3 MENU Exit
Shooting in Fast Forward Movie
mode starts.
Press the shutter release button.
Shooting in Fast Fwd Movie mode ends.
Ok
Playing Back Movie Pictures ☞ p.91
memo
86
• Off (×1) is the normal setting for movie pictures (15 frames
per second). Each time ×2 or ×5 is selected, the number of
frames taken per second is reduced to 1/2 or 1/5.
• As movie pictures are normally played back at the rate of 15
frames per second, movies taken at ×2 are played back twice
as fast and movies taken at ×5 are played back five times as
fast.
• Sound cannot be recorded.
e04_kb338_038_088_41e.qk 3/17/03 5:23 PM Page 87
Saving the Settings (Memory)
Saving the Menu Items (Memory)
You can choose whether you want the set values to be saved when the
camera is turned off. If you select [On], the settings will be saved in
the status they were in immediately before the camera was turned off. If
you select [Off], the settings will be reset to the defaults when the camera is turned off.
Item
Flash
White Balance
EV Compensation
Digital Zoom
AE Metering
Focus Mode
Zoom Position
MF Position
DISPLAY
File No.
memo
Default Setting
On
The focus position set by Manual Focus is saved.
The LCD monitor display mode is saved.
The file number is saved. If a new SD Memory Card/
MultiMediaCard is inserted, the sequential file number
is assigned.
Off
Off
On
Off
Off
Off
Off
Off
Off
On
Taking Pictures
Sensitivity
Description
The flash mode setting on the button is saved.
The [White Balance] setting on the [
Rec.Mode]
menu is saved.
The set EV compensation value is saved.
The [Digital Zoom] setting on the [
Rec.Mode] menu
is saved.
The [AE Metering] setting on the [
Rec.Mode] menu
is saved.
The [Sensitivity] setting on the [
Rec.Mode] menu is
saved.
The focus mode setting is saved.
The zoom position setting is saved.
• Menu items not included in [Memory] will also be saved in the
settings selected on the menus for each function when the
camera is turned off.
• The zoom position setting in the digital zoom range will not
be saved even if [Zoom Position] is set to On in [Memory].
• The Auto Bracket setting is not saved.
• [Memory] can be set separately in User mode and other
shooting modes.
87
e04_kb338_038_088_41e.qk 3/17/03 5:23 PM Page 88
z
x
Press the Menu/Fn button in
Capture mode.
Rec. Mode
Press the four-way controller
() to select [Memory].
c
Press the four-way controller ().
[Memory] menu will be displayed.
v
Use the four-way controller () to
select the item.
b
Use the four-way controller () to
switch [On] and [Off].
n
Press the OK button twice.
The camera is ready to take the
picture.
Memory
Sharpness
Saturation
Contrast
USER
3/3
MENU
Exit
OK
Ok
OK
Ok
Memory
Flash
White Bal.
EV Compensation
Digital Zoom
AE Metering
Sensitivity
1/2
MENU
Exit
On
Off
Off
On
Off
Off
Registering Functions in User Mode
Taking Pictures
By setting the mode dial to
and setting the shooting
functions, the functions and shooting mode are registered in
User mode.
● Functions that can be set in User mode
Function
Default
Setting
Instant Review*
Quality Level
Focusing Area
Sensitivity
Default
Setting
Ref.
2s (2 sec) p.50
p.44
Interval Shoot*
—
AWB
(Auto)
p.45
Fast Fwd Movie
[Off]
p.86
Parallel
p.65
Wide
p.47
Memory
—
p.87
p.48
Sharpness
Normal
p.51
AE Metering
88
Function
Recorded Pixels 2592×1944 p.43
White Balance
memo
Ref.
3D Mode*
p.80
Auto
p.49
Saturation
Normal
p.52
Auto Bracket*
—
p.84
Contrast
Normal
p.53
Digital Zoom
[On]
p.75
USER
—
• For the USER mode, you can choose from the following six
modes: program, manual exposure, aperture priority, shutter
priority, picture or digital filter mode.
• Settings made for functions marked with an asterisk (*) are
reflected in other modes as well as User mode.
e05_kb338_089_122_41e.qk 3/17/03 5:21 PM Page 89
Playback/Erasing
Playing Back Images and Sound
x
z
c
Playing Back Still Pictures
See “Playing Back Still Pictures” (p.26, 27).
Zoom Display
You can display images magnified up to 8 times. A guide to operation is displayed on the LCD monitor during magnification.
x
Enter the Playback mode and choose the image you
want to magnify with the four-way controller ().
Press /
on the Zoom/ /
button.
The image will be magnified (1× to
8×).
1.1X
Playback/Erasing
z
The following operations can be performed while the magnified image is displayed.
Four-way controller ()
Zoom /
/
button (
Zoom /
/
button (
Display button
)
: Moves the position to be magnified
: Makes the image larger
)
: Makes the image smaller
: Turns the guide marks on/off
89
e05_kb338_089_122_41e.qk 3/17/03 5:21 PM Page 90
c
If you set [Quick Zoom] in the [ Set-up] menu to On, when
the Zoom/
/
button ( /
) is pressed in Step x, the
image will be magnified eight times.
memo
Caution
Press the OK button.
Zoom playback will end.
Movie pictures cannot be magnified.
Adding a Voice Memo
You can add a voice memo to a recorded image.
z
Playback/Erasing
x
c
memo
90
Enter the playback mode and
choose the image to which you
want to add a voice memo with the
four-way controller ().
If the image has no voice memo, the
screen for recording a voice memo is
displayed on the LCD monitor.
100-0038
100-0019
02/20/2003
11:19
Press the OK button.
Recording starts. You can record for up to 30 seconds.
Press the OK button.
Recording stops.
v
Press the four-way controller ().
Play back the recorded voice memo.
b
Press the four-way controller ().
Playback stops.
• A voice memo cannot be added to protected (
) images.
•
is displayed on the LCD monitor next to images with a
voice memo.
e05_kb338_089_122_41e.qk 3/17/03 5:21 PM Page 91
v
zxc
Playing Back Movie Pictures
You can play back Movie pictures. A guide to operation is displayed on the LCD monitor during playback. The sound is
played back at the same time.
z
Enter the Playback mode and choose the movie picture
you want to play back with the four-way controller ( ).
x
Four-way controller ():
Reverse
playback
Forward
playback
Pause
Four-way controller ():
Four-way controller ():
Zoom/
/
button (
Zoom/
/
button (
Display button:
):
100-0019
02/20/2003
11:19
Increases the volume
Playback/Erasing
Press the four-way controller ().
Playback will start.
The following operations can be performed during playback.
): Reduces the volume
Changes the Display mode
The following operations can be performed while Pause is
engaged.
Four-way controller ():
Four-way controller ():
Four-way controller ():
Display button:
c
v
Frame reverse
Frame forward
Releases the Pause function
Changes the Display mode
Press the four-way controller ().
Movie playback will end.
Press the Playback button.
The camera will return to Capture mode.
91
e05_kb338_089_122_41e.qk 3/17/03 5:21 PM Page 92
v
zxc
Playing Back Sound
You can play back the recording you made in Voice Recording
mode.
z
x
Enter the Playback mode and choose the recording you
want to play back with the four-way controller ().
Press the four-way controller ().
Playback will start.
100-0001
Playback/Erasing
00 : 00: 0 0
00 : 12: 3 5
02/20/2003
11:19
Recording time
The following operations can be performed during playback.
Four-way controller ():
Four-way controller ():
Zoom/
Zoom/
c
v
92
playback time
/
/
button ( ):
button (
):
Rewinds and plays back the
recorded sound
Advances and plays back
the recorded sound
Increases the volume
Reduces the volume
Press the four-way controller ().
Sound playback will end.
Press the Playback button.
The camera will return to the Capture mode.
e05_kb338_089_122_41e.qk 3/17/03 5:21 PM Page 93
Playing back Shooting Information (Playback Mode)
You can display shooting information on the LCD monitor. Use
the Display button to change the information displayed.
Display On
Playback information is displayed.
Folder No.
File name
Protect icon
Four-way controller operation guide
Date & time
Battery indicator
1 23
100-0020
100-0019
02/20/2003
11:19
6
2 3 4
100-0021
2592
AWB
100
6
5
Playback/Erasing
02/20/2003
11:19
➞
➞
Display Off
No playback information is displayed.
➞
Histogram Display
The brightness distribution of the image
1
is displayed.
The x-axis shows the brightness (darkest at the left end and brightest at the
right end) and the y-axis shows the
number of pixels.
1/125
F2.6
Histogram
Recorded pixels
87
Quality level
White balance
AE metering
Sensitivity
Aperture value
Shutter speed
5 4
Display On
93
e05_kb338_089_122_41e.qk 3/17/03 5:21 PM Page 94
x
z
c
Nine-image Display
You can display nine images at the same time.
z
x
Playback/Erasing
c
memo
94
Enter the Playback mode and choose an image with the
four-way controller ().
Press
/
on the Zoom button
/
.
Nine images will be displayed with
the selected image in the center.
Choose an image with the four-way
controller ().
When ten or more images have
Selected image
been recorded, if you press the fourway controller () while the bottom right image is selected,
the next nine images will be displayed, and if you press the
four-way controller () while the top left image is selected,
the previous nine images will be displayed. Similarly, if you
press the four-way controller () while an image on the top
row is selected, the previous nine images will be displayed,
and if you press the four-way controller () while an image
on the bottom row is selected, the next nine images will be
displayed.
Press the OK button.
The screen will return to single-image display of the selected image.
Sound files are displayed in
.
e05_kb338_089_122_41e.qk 3/17/03 5:21 PM Page 95
zcv
b
x
Slideshow
You can play back all the images on the SD Memory
Card/MultiMediaCard continuously.
z
x
v
b
memo
Press the Menu/Fn button.
The [
Playback] menu will be
displayed.
Select [Slideshow] with the fourway controller ().
Use the four-way controller ()
to change the playback interval.
Choose from the following: 3 sec, 5
sec, 10 sec, 20 sec, 30 sec.
Playback
Resize
Trimming
Alarm
Slideshow
MENU
Exit
Off
3sec
OK
Ok
Playback/Erasing
c
Enter the Playback mode and choose the image with
which to start the slideshow with the four-way controller
().
Press the OK button.
Playback will start at the set interval.
• If you press the four-way controller, or any buttons such as
the Menu/Fn button during continuous playback, the
slideshow will stop.
• The slideshow will continue until you press any button.
• Movie pictures and pictures with a voice memo will be played
through to the end before the next picture is played back,
regardless of the set playback interval.
95
e05_kb338_089_122_41e.qk 3/17/03 5:21 PM Page 96
Erasing Images
x
zc
v
Erasing a Single Image or Sound
z
x
Playback/Erasing
96
c
v
Enter the Playback mode and choose the image or
sound you want to erase with the four-way controller
().
Press the
button.
The Delete screen will be displayed.
100-0020
Select [Delete] with the four-way
controller ().
Delete
Cancel
MENU
Press the OK button.
Exit
All images
ima & sounds OK Ok
• You can also delete images from Instant Review (p.25).
symbol).
• If [Quick Delete] is set to On in the [ Set-up] menu, Step c
can be omitted.
memo • You cannot erase protected images (with the
e05_kb338_089_122_41e.qk 3/17/03 5:21 PM Page 97
Erasing a Voice Memo
If an image has a voice memo, you can erase the voice memo
without erasing the image.
z
x
c
v
Enter the Playback mode and choose the image with the
voice memo that you want to erase with the four-way
controller ().
Press the
button.
The Delete screen will be displayed.
100-0020
Select [Sound Delete] with the
four-way controller ().
Press the OK button.
Sound Delete
Delete
Cancel
MENU
Exit
All images & sounds OK Ok
Select [Delete] in step c above to erase both the image and
memo the voice memo.
Playback/Erasing
97
e05_kb338_089_122_41e.qk 3/17/03 5:21 PM Page 98
z
x
c
Erasing All Images
You can erase all the images/sound at once.
• Once erased, images/sound cannot be restored.
• Protected images/sound cannot be erased.
Caution
z
Playback/Erasing
98
x
c
Enter the Playback mode and
press the
button twice.
The Delete screen will be displayed.
Select [Delete All] with the fourway controller ().
100-0020
Delete all images & sounds
on the memory card?
Delete All
Cancel
MENU
Exit
OK
Ok
Press the OK button.
If [Quick Delete] is set to On in the [Set-up] menu, step x can
memo be omitted.
e05_kb338_089_122_41e.qk 3/17/03 5:21 PM Page 99
x
z
c
Protecting Images from Deletion (Protect)
You can protect images/sound from being accidentally erased.
z
x
c
Press the four-way controller ().
The frame will move to [Protect].
Press the OK button.
Protect
Unprotect
MENU
Exit
All images & sounds OK Ok
• Select [Unprotect] in step c to release the Protect setting.
symbol is displayed when the
image/sound is played back.
memo • If the image is protected, the
Protecting All Images/Sound
You can protect all the images/sound.
z
x
c
v
Playback/Erasing
v
Enter the Playback mode and choose the image/sound
you want to protect with the four-way controller ().
Press the
button.
100-0020
The Protect screen will be displayed.
Enter the Playback mode.
Press the
button twice.
The protect all images & sounds screen will be displayed.
Press the four-way controller ().
The frame will move to [Protect].
Press the OK button.
Select [Unprotect] in step c above to cancel the Protect setting
memo on all the images.
Caution
Even protected images/sound will be erased by formatting
the SD Memory Card/MultiMediaCard.
99
e05_kb338_089_122_41e.qk 3/17/03 5:21 PM Page 100
Viewing Images on a TV
By using the AV cable, you can capture and play back images
on a TV or other equipment with a video IN jack. Make sure that
both the TV and the camera are turned off before connecting
the cable.
z
x
Playback/Erasing
c
Open the terminal cover and connect the AV cable.
Connect the sound terminal (white) and image terminal
(yellow) of the AV cable to the sound terminal (white) and
image input terminal (yellow) of the TV.
Turn the TV and camera on.
Changing the Video Output Format ☞ p.132
The LCD monitor is always turned off when the camera is con-
memo nected to a TV.
If you intend to use the camera for a long time, use of the AC
adapter (optional) is recommended. Refer to the operating manual for the TV or equipment to which the camera is connected.
100
e05_kb338_089_122_41e.qk 3/17/03 5:21 PM Page 101
Setting the Printing Service (DPOF)
You can print the images on the SD Memory Card/MultiMediaCard
using a DPOF (Digital Print Order Format) compatible printer or at a
printing service.
x
zcv
b
Printing Single Image
z
x
Enter the Playback mode and use the four-way controller
() to choose the image for which you want to make
DPOF settings.
Press the DPOF button.
The DPOF screen will be displayed.
100-0020
Copies
Date
MENU
Exit
DISP
Playback/Erasing
Set the following items for each image.
Copies
Set the number of prints up to a maximum of 99.
Date
Specify whether you want the date imprinted on the print or
not.
01
All Images
OK
Ok
101
e05_kb338_089_122_41e.qk 3/17/03 5:21 PM Page 102
c
Use the four-way controller () to
select the number of prints, then
press the four-way controller ().
The frame will move to [Date].
v
Use the four-way controller () to
select whether to insert the date or
not.
100-0020
Copies
Date
MENU
Exit
DISP
03
All Images
OK
Ok
: The date will be printed
: The date will not be printed
b
memo
Caution
Playback/Erasing
102
Press the OK button.
Prints can be made according to the settings.
• If DPOF settings have already been made for an image, the
previously set number of prints and On/Off date setting will
be displayed.
• To cancel DPOF settings, set the number of prints to 00 and
press the OK button.
• You cannot set the printing service for movie pictures.
• Depending on the printer or printing equipment at the
photo processing lab., the date may not be imprinted on
the pictures even if the DPOF setting was made.
e05_kb338_089_122_41e.qk 3/17/03 5:21 PM Page 103
z
xcv
b
Printing All Images
z
x
c
b
Use the four-way controller () to
select the number of prints.
You can print up to 99 copies.
100-0020
DPOF settings
for all images
Press the four-way controller ().
The frame will move to [Date].
Use the four-way controller () to
select
(On) or
(Off).
The date will be printed.
The date will not be printed.
Copies
Date
MENU
Exit
01
OK
Ok
Press the OK button.
Prints can be made according to the settings.
Playback/Erasing
v
Enter the Playback mode and press the DPOF button
twice.
The [All Images] screen will be displayed.
• The setting for a single image will be cancelled.
memo • When you specify the number of prints in the DPOF setting,
the number applies to all the images. Before printing, check
that the number is correct.
• The setting is not possible for movie pictures.
103
e05_kb338_089_122_41e.qk 3/17/03 5:21 PM Page 104
Viewing Images with your PC
By using the provided USB cable (I-USB7) or card reader and
image-browser software, you can transfer images recorded with
the camera to your PC and edit them or print them out.
This section explains how to view images on your PC using the
provided USB driver and software.
About the included software
The included CD-ROM (S-SW7) contains the following software:
- USB driver
- Image viewing software (ACDSee™)
- ACD Photostitcher
ACD photostitcher is only for the English and the Japanese
version.
System environment
OS:
Playback/Erasing
Windows 98/98 SE/2000/Me
Windows XP Home Edition/Professional
CPU:
Pentium or later recommended
Memory: 64MB or more
Hard disk space: 15MB or more
Standard equipped USB port
To view movie pictures on your PC, Direct X 8.0 or later and
Media Player pre-installed on system, or QuickTime 3.0 or later
are required. For Windows Me/XP, Media Player pre-installed on
system, QuickTime 3.0 or later is required.
Caution
104
• Not compatible with Windows 95/NT.
• When you connect the camera to your PC, you are recommended to use the AC adapter kit D-AC7.
If the battery power runs out while image data is being
transferred, the data may be lost.
e05_kb338_089_122_41e.qk 3/17/03 5:21 PM Page 105
Installing the software
This section describes the procedures for installing the necessary software.
Installing the USB driver ☞ p.105
Installing the image processing software (ACDSee™ and
ACD photostitcher) ☞ p.110
Installing the USB driver on Windows 98/98 SE only
If you are using Windows 2000, Windows Me or Windows XP,
you do not need to install the USB driver. When you connect the
camera to your computer with the USB cable, your computer will
automatically detect the camera as [Removable Disk].
z
x
c
Turn your computer on.
Insert the CD-ROM (S-SW7) into the CD-ROM drive.
Make sure the camera is turned off and connect it to
your computer with the USB cable.
Make sure that there is an SD Memory Card/MultiMedia
Card in the camera.
Playback/Erasing
v
Turn your camera on.
Your computer will automatically detect the camera as new
hardware and the Wizard screen will appear.
105
e05_kb338_089_122_41e.qk 3/17/03 5:21 PM Page 106
b
n
m
Playback/Erasing
106
,
Click [Next].
Select [Search for the best
driver for your device] and
click [Next].
Select [Specify a location]
in the box on the left and
click [Browse].
If another item has been
selected, click the box to
deselect it.
Click the CD-ROM drive
icon and click [OK].
The figure on the right is displayed when the CD-ROM is
set as the F drive.
e05_kb338_089_122_41e.qk 3/17/03 5:21 PM Page 107
.
⁄0
⁄1
⁄3
Make sure that
[PENSSTOR.INF] is displayed and click [Next].
Installation of the driver
starts.
Click [Finish].
When installation is finished,
installation of the driver for
the new hardware starts.
Click [Next].
Playback/Erasing
⁄2
Make sure that the specified
drive is displayed and click
[Next].
Select [Search for the best
driver for your device] and
click [Next].
107
e05_kb338_089_122_41e.qk 3/17/03 5:21 PM Page 108
⁄4
⁄5
⁄6
Playback/Erasing
108
⁄7
Select [Specify a location]
and click [Browse].
If another item has been
selected, click the box to
deselect it.
Click the CD-ROM drive
icon and click [OK].
The figure on the right is displayed when the CD-ROM is
set as the F drive.
Make sure that the specified
drive is displayed and click
[Next].
Make sure that
[PENSPDR.INF] is displayed
and click [Next].
e05_kb338_089_122_41e.qk 3/17/03 5:21 PM Page 109
⁄8
⁄9
Click [Finish].
When installation is finished,
the Wizard window is exited.
Double-click [My Computer]
on the desktop.
A removable disk will be
added.
Playback/Erasing
109
e05_kb338_089_122_41e.qk 3/17/03 5:21 PM Page 110
Installing the image processing software
This section describes the procedures for installing ACDSee™
which lets you view recorded images on your computer and
ACD photostitcher which lets you create panorama pictures.
• The ACD photostitcher is only for the English version and
the Japanese version.
• If you are using Windows 2000 or Windows XP, login by
the authority of the administrator before installing the
software. See the operating manual for your computer for
instructions on how to login.
Caution
Installing the ACDSee™
When installing the ACDSee™, recorded images can be viewed
and edited on your computer.
z
x
Turn on your computer.
Insert the CD-ROM (S-SW7) into your CD-ROM drive.
The PENTAX Software Installer screen will appear.
If the PENTAX Software Installer screen is not displayed
Playback/Erasing
110
Follow the procedure below to display the screen.
1) Double click the [My Computer] icon on the desktop.
2) Double click the [CD-ROM Drive (S-SW7)] icon.
3) Double click the [Setup.exe] icon.
c
v
Click your applicable language.
You can choose the language from the following: English,
French, German, Spanish, Italian and Japanese.
Click the [ACDSee™].
The Setup screen will appear. Follow the on-screen guidance and enter the registration information. Reboot your PC
after installation finish.
e05_kb338_089_122_41e.qk 3/17/03 5:21 PM Page 111
Installing the ACD photostitcher
The ACD photostitcher is only for the English and Japanese version. If you have installed ACDSee™ and ACD photostitcher in
your computer, you can join the images you have taken in
Panorama assist mode.
Make sure that the ACDSee™ has been installed.
z
x
Turn on your computer.
Insert the CD-ROM (S-SW7) into your CD-ROM drive.
The PENTAX Software Installer screen will appear.
If the PENTAX Software Installer screen is not displayed
Follow the procedure below to display the screen.
1) Double click the [My Computer] icon on the desktop.
2) Double click the [CD-ROM Drive (S-SW7)] icon.
3) Double click the [Setup.exe] icon.
c
v
Playback/Erasing
Click your applicable language.
You can choose the language from the following: English,
French, German, Spanish, Italian and Japanese.
Click the [ACD Photostitcher].
The Setup screen will appear. Follow the on-screen guidance and enter the registration information.
The screen will return to PENTAX Software Installer. Click
the [Exit] to finish.
111
e05_kb338_089_122_41e.qk 3/17/03 5:21 PM Page 112
Displaying and copying images using ACDSee™
z
x
c
Playback/Erasing
112
v
Turn your computer on.
Make sure the camera is turned off and connect it to
your computer with the USB cable.
Make sure that there is an SD Memory Card/MultiMedia
Card in the camera.
Turn your camera on.
ACDSee starts up automatically and the list of images is
displayed. Go to Step b.
If ACDSee fails to start
up automatically, double-click the [ACDSee]
icon on the desktop.
Your camera can be
found in the [My
Computer] window as
[Removable Disk].
Camera images can be
found in [My Computer]
→ [Removable Disk (or the name on the volume label on
the SD Memory Card/MultiMedia Card, if there is one)] →
[DCIM] → [XXXPENTX]. (XXX is a 3-digit number.)
A list of the images will be displayed.
e05_kb338_089_122_41e.qk 3/17/03 5:21 PM Page 113
b
n
Select the image you want to view from the list.
Double-click the selected image to enlarge it to full-screen
display.
Copy the image to your computer.
Select an image from the list and copy it to the desired folder in your computer. Refer to the operating manual for your
computer for copying instructions.
You can also copy images using Internet Explorer for Windows.
If you are using Windows XP and there is a volume label on the
memo SD Memory Card/MultiMedia Card, the name on the volume label
will be displayed instead of [Removable Disk]. If the card is unformatted, the manufacturer and type of card may be displayed.
Joining panorama images using ACD photostitcher
The ACD photostitcher is only for the English and the Japanese
version.
When you have installed ACDSee™ and ACD photostitcher, you
can join images recorded in Panorama Assist mode to make
panorama pictures.
The folder names and image names displayed on the screen for
explanation purposes may vary depending on your operating
system.
x
Start up ACDSee™.
See p.112 for instructions on how to start up ACDSee™.
Select the images you want to join from the list.
To select more than one image at a time, click on the
images while pressing the [Ctrl] key on the keyboard.
When you have selected the images, click the [ACD photostitcher] button on the tool bar.
If no images have been selected, the [ACD photostitcher]
button is disabled.
Playback/Erasing
z
Click the [ACD photostitcher] button
Select the images
113
e05_kb338_089_122_41e.qk 3/17/03 5:21 PM Page 114
c
Adjust the position of the images.
ACD photostitcher starts up and the selected images are
displayed in panorama format.
If you move the mouse pointer onto an image, the pointer
changes to a
symbol. Adjust the position of the images
by pressing the left mouse button and moving the images
one by one to the desired position.
When you have finished correcting the position, click the
[STITCH] button.
Click the [STITCH]
button
Adjust the position
while pressing the
left mouse button
v
Playback/Erasing
114
Select the type of panorama picture you want to create.
There are two types of panorama picture: [Flat] and
[Cylindrical]. As the former type is used in this explanation,
click the [Flat] button.
A dialog box will appear. Click [OK].
Click [Flat]
e05_kb338_089_122_41e.qk 3/17/03 5:21 PM Page 115
b
Trim the picture.
If you move the mouse pointer onto the dotted line around
the picture, the pointer changes to a symbol. Trim the picture by pressing the left mouse button and moving the dotted line.
When you have finished trimming, click the [TRIMMING]
button.
Click the [TRIMMING] button.
Trim the picture.
n
Click the [SAVE] button.
[CANCEL] button
Playback/Erasing
Save the picture.
When you are satisfied with the trimmed picture, click the
[SAVE] button to save the picture.
To cancel trimming, click the [CANCEL] button.
After saving the picture, if you have finished creating
panorama pictures, exit [ACD photostitcher] and [ACDSee].
115
e05_kb338_089_122_41e.qk 3/17/03 5:21 PM Page 116
Disconnecting the camera from your computer
Disconnecting your camera from your PC (Windows 2000/Me)
z
x
Double-click the
(Hot Plug)
icon on the status bar at the
bottom right of the desktop.
The [Unplug or Eject Hardware]
screen will appear.
Make sure that [PENTAX USB
DISK Device] is selected and
click [Stop].
The [Stop a Hardware device]
screen will appear.
PENTAX USB DISK Device at PENTAX OPTIO 550
c
Playback/Erasing
116
v
b
Make sure that [PENTAX USB
DISK Device] is selected and
click [OK].
A message will appear.
Click [OK].
Unplug the USB cable from
your computer and camera.
e05_kb338_089_122_41e.qk 3/17/03 5:21 PM Page 117
Disconnecting your camera from your PC (Windows XP)
z
x
Double-click [Safely Remove
Hardware] on the task bar.
Click [PENTAX USB DISK
Device] and click [Stop].
PENTAX USB DISK Device at PENTAX OPTIO 550
c
A message permitting removal
of the hardware will appear.
Turn the camera off and unplug
the USB cable from your computer and camera.
Playback/Erasing
v
Click [PENTAX USB DISK
Device] and click [OK].
Disconnecting your camera from your PC (Windows 98/98 SE)
Windows 98 and 98 SE have no Hot Plug icon. To disconnect
the camera, turn the camera off and unplug the USB cable.
117
e05_kb338_089_122_41e.qk 3/17/03 5:21 PM Page 118
Viewing Images with your Macintosh
By using the provided USB cable (I-USB7) or card reader and
image-browser software, you can transfer images recorded with
the camera to your Macintosh and edit them or print them out.
This section explains how to view images on your Macintosh
using the provided USB driver and software.
About the included software
The included CD-ROM (S-SW7) contains the following software:
• Image-browser software (ACDSee™)
System environment
OS:
Mac OS 8.6 or later (QuickTime 4.0 or later required)
CPU:
Power PC 266MHz or higher
Memory: 8MB or more
Hard disk space: 6MB or more
Standard equipped USB port
Playback/Erasing
Caution
• When you connect the camera to your Macintosh, you
are recommended to use the AC adapter. If the battery
power runs out while image data is being transferred,
the data may be lost.
Installing the software
Installing the USB Driver and the ACDSee™ on your
Macintosh
The procedures for installing the necessary software are
explained.
Many current and recent Macintosh computers will automatically
recognize the camera and load their own USB mass storage
drivers. When you attach the camera to your Mac, the camera
should automatically appear on your desktop as an “untitled”
disk drive, which you can double click to access.
118
e05_kb338_089_122_41e.qk 3/17/03 5:21 PM Page 119
Installing the image processing software
z
x
c
v
b
n
Turn your Macintosh on.
Insert the CD-ROM (S-SW7) into the CD-ROM drive.
Double-click the CD-ROM (S-SW7) icon.
Double-click the [Master Installer] icon.
Double-click the [Master Installer] alias icon.
The PENTAX Software Installer screen will appear.
Click the applicable language.
The screen for selecting the software you want to install will be
displayed.
Install ACDSee™
When you have installed ACDSee™, you can edit recorded
images on your Macintosh.
m
Playback/Erasing
Click [ACDSee™].
The Setup screen will appear.
Follow the on-screen instructions to enter the registration
information and install the software.
When installation is finished, reboot your Macintosh.
119
e05_kb338_089_122_41e.qk 3/17/03 5:21 PM Page 120
Displaying and copying images using ACDSee™
z
x
Playback/Erasing
c
v
b
n
m
120
Turn your Macintosh on
Make sure the camera is turned off and connect it to
your Macintosh with the USB cable.
Make sure that there is an SD Memory Card/MultiMedia
Card in the camera.
Turn your camera on.
Your camera can be found on the
desktop as [untitled]. You can
change the folder name.
Click the [ACDSee™] folder on the hard drive.
Double-click the [ACDSee™] program icon.
Open the camera folder.
Camera images can be found in [untitled (or the name on
the volume label on the SD Memory Card/MultiMedia Card,
if there is one)] → [DCIM] → [XXXPENTX]. (XXX is a 3-digit
number.)
Select the image you want to view from the list.
Double-click the selected image to enlarge it to full-screen
display.
e05_kb338_089_122_41e.qk 3/17/03 5:21 PM Page 121
,
Copy the image to your Macintosh.
Refer to the operating manual for your Macintosh for instructions
on copying or moving files.
Before editing an image, copy it to your Macintosh first.
If there is a volume label on the SD Memory Card/MultiMedia
memo Card, the name on the volume label will be displayed instead of
[untitled]. If the card is unformatted, the manufacturer and type
of card may be displayed.
Disconnecting the camera from your Macintosh
z
x
Drag the [untitled (or the name on the volume label on
the SD Memory Card/MultiMedia Card, if there is one]
folder on the desktop to Trash.
Unplug the USB cable from your Macintosh and camera.
Playback/Erasing
121
e05_kb338_089_122_41e.qk 3/17/03 5:21 PM Page 122
MEMO
122
e06_kb338_123_157_41e.qk 3/17/03 4:10 PM Page 123
Editing/Settings
Editing Images
Four-way controller
OK button
Menu/Fn button
Changing the Image Size
By changing the size and quality of a selected image, you can
make the file smaller than the original. After changing the size,
the image can be saved as a new image or written over the
original image.
z
x
c
v
Press the Menu/Fn button.
Press the four-way controller ().
The [
Playback] menu will be displayed.
Press the four-way controller () to select [Resize].
Press the four-way controller ().
The Resize screen will be displayed.
100-0020
b
Exit
OK
Use the four-way controller ( ) to choose the image
you want to resize.
Ok
Editing/Settings
MENU
123
e06_kb338_123_157_41e.qk 3/17/03 4:10 PM Page 124
n
Press the OK button.
100-0020
Select resolution
and quality
Recorded Pixels
Quality Level
MENU
m
,
.
⁄0
⁄1
⁄2
640×480
Exit
OK
Ok
Press the four-way controller () to select [Recorded
pixels].
Press the four-way controller ().
The frame will move to [Quality Level].
Press the four-way controller () to select [Quality
Level].
Press the OK button.
Press the four-way controller () to select [Overwrite]
or [Save as].
Press the OK button.
The image will be resized.
• Movie pictures cannot be resized.
memo • You cannot select a larger size than that of the original
image.
• You cannot select a higher quality level than that of the original image.
• TIFF images cannot be resized.
Editing/Settings
124
e06_kb338_123_157_41e.qk 3/17/03 4:10 PM Page 125
Trimming Images
You can trim part of a picture and save it as a separate image.
z
x
c
v
b
n
m
Press the Menu/Fn button.
Press the four-way controller ().
The [
Playback] menu will be displayed.
Press the four-way controller () to select [Trimming].
Press the four-way controller ().
The image that can be trimmed.
Choose the image you want to trim with the four-way
controller ().
Press the OK button.
The trimming screen will be displayed.
100-0020
Trim the image.
Operations available on the Trimming
screen.
Zoom/
Size
Exit
DISP
OK
Rotate
OK
⁄0
button
Press the OK button.
Select the quality level after trimming with the four-way controller
().
Press the OK button.
The trimmed image will be saved as
a separate image.
100-0020
Select image quality
Editing/Settings
: Changes the size of the
image
Display button
: Switches between horizontal
and vertical
Four-way controller () : Moves the trimming position
up, down, right and left
Menu/Fn button
: Returns to the screen for
selecting an image to be
trimmed
,
.
/
MENU
Quality Level
MENU
Exit
OK
Ok
• Movie pictures cannot be trimmed.
memo • You cannot select a higher quality than that of the original
image.
• TIFF images cannot be trimmed.
125
e06_kb338_123_157_41e.qk 3/17/03 4:11 PM Page 126
Camera Settings
How to recall [
Set-up] menu
Rec. Mode
Recorded Pixels
Quality Level
White Balance
Focusing Area
AE Metering
Sensitivity
Four-way controller
1/3
MENU
2592 1944
Exit
AWB
Wide
Auto
OK
Ok
OK button
Menu button
Formatting a SD Memory Card/MultiMediaCard
Formatting will delete all the data on the SD Memory
Card/MultiMediaCard.
• Do not remove the SD Memory Card/MultiMediaCard
while the card is being formatted. The card may be damaged and become unusable.
• SD Memory Cards/MultiMedia Cards formatted on a PC
or device other than the camera cannot be used. Be sure
to format the card with the camera.
• Formatting will delete protected data too.
Caution
Editing/Settings
126
z
x
c
v
Select [Format] on the [
Set-up] menu.
Press the four-way controller ().
The Format screen will be displayed.
Select [Format] with the four-way controller ().
Press the OK button.
Formatting will start. When formatting is completed,
the camera is ready to capture or play back images.
e06_kb338_123_157_41e.qk 3/17/03 4:11 PM Page 127
Set-up
Twice
Format
Sound
Date Style
Date Adjust
World Time
Language/
1/3
MENU
mm.dd.yy
1/ 1/2003
Off
English
Exit
OK
Ok
Changing the Sound Settings
You can change the volume of the start-up sound, shutter sound
and operation sounds. You can also change the type of each
sound.
Changing the volume
z
x
v
Set-up] menu.
Press the four-way controller ().
The Sound screen will be displayed.
Use the four-way controller () to
change the volume.
Press the OK button twice.
The camera is ready to capture or
play back images.
Sound
Volume
Start-up Sound
Shutter Sound
Operation Sound
MENU
Exit
1
1
1
OK
Ok
Editing/Settings
c
Select [Sound] on the [
127
e06_kb338_123_157_41e.qk 3/17/03 4:11 PM Page 128
How to recall [
Set-up] menu
Rec. Mode
Recorded Pixels
Quality Level
White Balance
Focusing Area
AE Metering
Sensitivity
Four-way controller
1/3
MENU
2592 1944
AWB
Wide
Auto
Exit
OK
Ok
OK button
Menu/Fn button
Changing the type of start-up, shutter or operation sound
z
x
c
v
b
Editing/Settings
128
Select [Sound] on the [
Set-up] menu.
Press the four-way controller ().
The Volume screen will be displayed.
Press the four-way controller () to select [Startup
Sound] and choose [1], [2], [3] or [off] with the four-way
controller ().
Change the [Shutter sound] and [Operation Sound] in
the same way.
Press the OK button twice.
The camera is ready to capture or play back images.
e06_kb338_123_157_41e.qk 3/17/03 4:11 PM Page 129
Set-up
Twice
Format
Sound
Date Style
Date Adjust
World Time
Language/
1/3
MENU
Exit
mm.dd.yy
1/ 1/2003
Off
English
OK
Ok
Setting the Date Style
You can set the style in which the date is displayed on the camera. Choose [mm/dd/yy], [dd/mm/yy] or [yy/mm/dd].
z
x
c
memo
Select [Date Style] on the [
Set-up] menu.
Use the four-way controller () to change the date
style.
Press the OK button.
The camera is ready to capture or play back images with
the selected date style.
The style in which the time is displayed is set by [Date Adjust].
Editing/Settings
129
e06_kb338_123_157_41e.qk 3/17/03 4:11 PM Page 130
How to recall the [
Set-up] menu
Rec. Mode
Recorded Pixels
Quality Level
White Balance
Focusing Area
AE Metering
Sensitivity
1/3
Four-way controller
MENU
Exit
2592 1944
AWB
Wide
Auto
OK
Ok
OK button
Menu/Fn button
Changing the Date/Time
You can change the initial date and time settings.
z
x
Select [Date Adjust] on the [
Set-up] menu.
Press the four-way controller ().
The date screen will be displayed.
See “Setting the Date and Time” (p.22) for the setting procedure.
Setting the World Time
Editing/Settings
The city and time selected in “Initial Settings” (p.20) serve as the
Home Time setting.
You can display the time in a city other than the Home Time city
(World Time) when shooting or playing back.
z
x
Select [World Time] on the [
Set-up] menu.
Press the four-way controller ().
The World Time screen will be displayed.
World Time
NYC
TYO
MENU
130
Exit
04:18
17:18
OK
Ok
e06_kb338_123_157_41e.qk 3/17/03 4:11 PM Page 131
Set-up
Twice
Format
Sound
Date Style
Date Adjust
World Time
Language/
1/3
c
MENU
Exit
Switch
(On) and
troller ( ).
On
Off
mm.dd.yy
1/ 1/2003
Off
English
OK
Ok
(Off) with the four-way con-
: The time in the country selected in World Time will be
displayed.
: The time in the country selected in Home Time will be
dis-played.
v
Press the four-way controller ().
If New York is selected as the world time city, then the
cross-shaped line is located in New York on the world map,
and then
indicates the current time in New York (NYC).
b
Use the four-way controller () to select the World Time
city and press the four-way controller ().
Select [DST] On (
().
) or Off with the four-way controller
m
Press the four-way controller ().
Tokyo (TYO) is selected as the Home Time city [
,
Repeat steps b and n to change the Home Time city
and DST setting.
.
] at first.
Editing/Settings
n
Press the OK button twice.
The camera is ready to capture or play back images with
the time in the selected city.
memo See p.141 for the list of cities and code names.
131
e06_kb338_123_157_41e.qk 3/17/03 4:11 PM Page 132
How to recall the [
Set-up] menu
Rec. Mode
Recorded Pixels
Quality Level
White Balance
Focusing Area
AE Metering
Sensitivity
Four-way controller
1/3
MENU
Exit
2592 1944
AWB
Wide
Auto
OK
Ok
OK button
Menu/Fn button
Changing the Display Language
You can change the language in which the menus, error messages, etc. are displayed.
z
x
c
Select [Language] on the [
Set-up] menu.
Use the four-way controller () to select the language.
The menus will be displayed in selected language.
Press the OK button.
The camera is ready to take or play back images.
Changing the Video Output Format
Editing/Settings
132
You can select the output format (NTSC or PAL) for taking or
playing back images on a TV monitor.
z
x
c
Select [Video Out] on the [
Set-up] menu.
Use the four-way controller () to change the video
output format.
Press the OK button.
The camera is ready to take or play back images.
e06_kb338_123_157_41e.qk 3/17/03 4:11 PM Page 133
Set-up
Twice
Format
Sound
Date Style
Date Adjust
World Time
Language/
1/3
MENU
Exit
mm.dd.yy
1/ 1/2003
Off
English
OK
Ok
Changing the Start-up Screen
You can display an image recorded with the camera as the
welcome screen when the camera is turned on.
z
x
Select [Start-up Screen] on the [
Press the four-way controller ().
The Start-up screen will be displayed.
Set-up] menu.
Start-up Screen
Opening screen
MENU
c
n
Use the four-way controller () to select
(Off).
The start-up screen is displayed.
The start-up screen is not displayed.
DPOF
Image
OK
Ok
(On) or
Press the DPOF button.
Use the four-way controller () to choose the image
you want to display as the start-up screen.
Editing/Settings
v
b
Exit
Press the OK button three times.
The camera is ready to take or play back images.
Once the start-up screen has been set, it will not be erased
memo even if the original image is deleted or the SD Memory
Card/MultiMediaCard is formatted. To delete the start-up screen,
reset the setting. (☞ p.138)
133
e06_kb338_123_157_41e.qk 3/17/03 4:11 PM Page 134
How to recall the [
Set-up] menu
Rec. Mode
Recorded Pixels
Quality Level
White Balance
Focusing Area
AE Metering
Sensitivity
Four-way controller
1/3
MENU
2592 1944
AWB
Wide
Auto
Exit
OK
Ok
OK button
Menu/Fn button
LCD Power Saving (Sleep Timeout)
You can set the LCD monitor to turn off automatically when no
operation is performed for a fixed time.
z
x
c
memo
Editing/Settings
134
Select [Sleep Timeout] on the [
Set-up] menu.
Use the four-way controller () to select [30 sec], [1
min], [2 min] or [Off].
Press the OK button.
The camera is ready to take or play back images.
• This function will not work in Playback mode and using the
USB cable and when the camera is operated by optional AC
adapter.
Setting Auto Power Off
You can set the camera to turn off automatically when no operation is performed for a fixed time.
z
x
Select [Auto Power Off] on the [
Set-up] menu.
Use the four-way controller () to select [3 min],
[5 min] or [Off].
e06_kb338_123_157_41e.qk 3/17/03 4:11 PM Page 135
Set-up
Twice
Format
Sound
Date Style
Date Adjust
World Time
Language/
1/3
c
MENU
mm.dd.yy
1/ 1/2003
Off
English
Exit
OK
Ok
Press the OK button.
The camera is ready to capture or play back images.
• The menu screen turns off 1 minute after the last operation.
memo • The Auto Power Off function will not work when the USB
cable is connected.
Setting the Quick Delete Function
When the Quick Delete function is set to On, the Delete screen
will be displayed when [Delete] or [Delete All] is selected.
Select [Quick Delete] on the [
Set-up] menu.
Use the four-way controller () to select [On] or [Off].
Press the OK button.
The camera is ready to capture or play back images.
Setting the Quick Zoom Function
When the Quick Zoom function is set to On, images can be displayed at maximum magnification simply by pressing the Zoom
button once during zoom playback.
z
x
c
Select [Quick Zoom] on the [
Editing/Settings
z
x
c
Set-up] menu.
Use the four-way controller to () select [On] or [Off].
Press the OK button.
The camera is ready to capture or play back images.
135
e06_kb338_123_157_41e.qk 3/17/03 4:11 PM Page 136
How to recall the [
Set-up] menu
Rec. Mode
Recorded Pixels
Quality Level
White Balance
Focusing Area
AE Metering
Sensitivity
Four-way controller
1/3
MENU
2592 1944
AWB
Wide
Auto
Exit
OK
Ok
OK button
Menu/Fn button
Registering Functions
You can register the functions you use most frequently on the
four-way controller. The functions can then be set directly by
pressing the four-way controller, without displaying the
[Rec.Mode] menu.
Registering a function
z
x
c
Editing/Settings
v
b
memo
136
Select [Fn Setting] on the [
Set-up] menu.
Press the four-way controller ().
The Fn Setting screen will be displayed.
Use the four-way controller () to choose the key
where you want to register a function.
Use the four-way controller () to choose the function
you want to register.
If you do not want to register a function, select Off.
Press the OK button twice.
The camera is ready to capture or play back images.
• Only one function can be registered on each key of the fourway controller.
• You can choose from the following 11 functions: Recorded
Pixels, Quality Level, White Balance, Focusing Area, AE
Metering, Sensitivity, Digital Zoom, Instant Review,
Sharpness, Saturation and Contrast.
e06_kb338_123_157_41e.qk 3/17/03 4:11 PM Page 137
Twice
Set-up
Format
Sound
Date Style
Date Adjust
World Time
Language/
1/3
MENU
mm.dd.yy
1/ 1/2003
Off
English
Exit
OK
Ok
Retrieving a function
z
x
c
Enter the Capture mode and press
the Menu/Fn button and the fourway controller key () on
which a function is registered at
the same time.
White Balance
AWB
Press the four-way controller
() while pressing the Menu/Fn button to change
the setting.
Release the Menu/Fn button.
The setting is saved and the camera is ready to take the
picture.
Checking the status
Press the Menu/Fn button and the
Display button at the same time.
The function settings will be displayed.
Recorded Pixels
Quality Level
White Balance
Focusing Area
2592 1944
AWB
Wide
Editing/Settings
z
137
e06_kb338_123_157_41e.qk 3/17/03 4:11 PM Page 138
How to recall the [
Set-up] menu
Rec. Mode
Recorded Pixels
Quality Level
White Balance
Focusing Area
AE Metering
Sensitivity
1/3
Four-way controller
MENU
2592 1944
AWB
Wide
Auto
Exit
OK
Ok
OK button
Menu/Fn button
Adjusting the Focus Limit
You can choose whether or not to limit the movement of the
lens when shooting normally and in macro mode.
z
x
c
Select [Focus Limiter] on the [
Set-up] menu.
Press the four-way controller () to select [On] or [Off].
Press the OK button.
The camera is ready to capture or play back images.
Resetting to Default Settings (Reset)
You can reset all the settings other than the date and time, language, Video output format, world time and date style.
Editing/Settings
138
z
x
c
v
Select [Reset] on the [
Set-up] menu.
Press the four-way controller button ().
The Reset screen will be displayed.
Use the four-way controller () to select [Reset].
Press the Playback/OK button.
The camera is ready to capture or play back images.
e06_kb338_123_157_41e.qk 3/17/03 4:11 PM Page 139
Setting the Alarm
You can set the alarm to ring at a specified time and display a
selected image.
DPOF button
Four-way controller
OK button
Menu/Fn button
Checking the Alarm
z
x
c
v
Press the Menu/Fn button.
Press the four-way controller ().
The [
Playback] menu will be displayed.
Press the four-way controller () to select [Alarm].
Press the four-way controller ().
The list of alarms will be displayed.
Active alarms are indicated by
.
Alarm
Once
2
Everyday
3
Off
5:30AM
7:30AM
12:00PM
Exit
OK
Ok
Press the OK button twice.
If any alarms are enabled, the camera will be turned off and
the alarms will be set.
Editing/Settings
MENU
b
1
Setting the Alarm
z
x
c
Press the Menu/Fn button.
Press the four-way controller ().
The [
Playback] menu will be displayed.
Press the four-way controller () to select [Alarm].
139
e06_kb338_123_157_41e.qk 3/17/03 4:11 PM Page 140
v
Press the four-way controller ().
The list of alarms will be displayed.
Alarm
MENU
b
n
m
,
.
⁄0
1
Once
2
Everyday
3
Off
5:30AM
7:30AM
12:00PM
Exit
OK
Ok
Press the four-way controller () to select alarm 1-3.
Press the four-way controller ().
The screen for setting the alarm
mode and time will be displayed.
Four-way controller ()
Selects the item.
Four-way controller ()
Changes the setting.
1
Alarm
5:30AM
Once
MENU
Exit
DPOF
Image
OK
Ok
Press the DPOF button.
Press the four-way controller () to select the image to
be displayed when the alarm rings.
Press the OK button.
Press the OK button 3 times.
The camera will turn off.
Turning the Alarm Off
Editing/Settings
When the camera is turned off and the set time is reached, the
alarm will ring for one minute .
The camera will turn off automatically when the alarm has finished ringing.
• To stop the alarm ringing, press any button.
memo • If the Snooze function is set to On, the alarm will ring 5 times
at 5-minute intervals.
• To cancel the Snooze function, press the Menu/Fn button and
OK button at the same time.
Caution
140
The alarm will not ring when the camera is turned on.
e06_kb338_123_157_41e.qk 3/17/03 4:11 PM Page 141
Appendix
List of City Names
Refer to following list of city and code names for setting the world time.
City names
Pagopago
Honolulu
Anchorage
Vancouver
San Francisco
Los Angeles
Calgary
Denver
Mexico City
Chicago
Miami
Toronto
New York
San Diego
Caracas
Halifax
Buenos Aires
Sao Paulo
Rio de Janeiro
Madrid
London
Paris
Milan
Rome
Berlin
Johannesburg
Istanbul
Cairo
Jerusalem
Moscow
Jeddah
Code
THR
DXB
KHI
KBL
MLE
DEL
CMB
KTM
DAC
RGN
BKK
KUL
VTE
SIN
PNH
SGN
JKT
HKG
PER
BJS
SHA
MNL
TPE
SEL
ADL
TYO
GUM
SYD
NOU
WLG
AKL
City names
Tehran
Dubai
Karachi
Kabul
Male
Delhi
Colombo
Kathmandu
Dacca
Rangoon
Bangkok
Kuala Lumpur
Vientiane
Singapore
Phnom Penh
Ho chi Minh
Jakarta
Hong Kong
Perth
Beijing
Shanghai
Manila
Taipei
Seoul
Adelaide
Tokyo
Guam
Sydney
Noumea
Wellington
Auckland
Appendix
Code
PPG
HNL
ANC
YVR
SFO
LAX
YYC
DEN
MEX
CHI
MIA
YTO
NYC
SCL
CCS
YHZ
BUE
SAO
RIO
MAD
LON
PAR
MIL
ROM
BER
JNB
IST
CAI
JRS
MOW
JED
141
e06_kb338_123_157_41e.qk 3/17/03 4:11 PM Page 142
List of Menu Default Settings
[
Rec.Mode] Menu
Item
Recorded Pixels
Quality Level
White Balance
Focusing Area
AE Metering
Sensitivity
Auto Bracket
Digital Zoom
Instant Review
Interval Shooting
Fast Fwd Movie
3D Mode
Memory
Sharpness
Saturation
Contrast
USER
[
Playback] Menu
Item
Resize
Trimming
Alarm
Slideshow
Appendix
142
Default Setting
2592×1944 ( : 320×240)
AWB (Auto)
Wide
Auto
—
On
2 sec
—
Off
Parallel
—
Normal
Normal
Normal
Default Setting
—
—
[Off]
3 sec (3 sec. intervals)
e06_kb338_123_157_41e.qk 3/17/03 4:11 PM Page 143
[
Set-up] Menu
Item
Format
Sound
Date Style
Date Adjust
World Time
Language/
Start-up Screen
Video Out
Sleep Timeout
Auto Power Off
Quick Delete
Quick Zoom
Fn Setting
Focus Limit
Reset
Default Setting
—
—
mm/dd/yy
2003/01/01
Off
English
On
NTSC
1 min
3 min.
Off
Off
—
On
—
Appendix
143
e06_kb338_123_157_41e.qk 3/17/03 4:11 PM Page 144
Adjustable [Rec.Mode] Menu Items by Shooting Mode
: Changes are reflected in all camera operations
: Only default setting is reflected in camera operations;
changes are invalid
Item
Recorded Pixels
Quality Level
White Balance
Focusing Area
AE Metering
Sensitivity
Auto Bracket
Digital Zoom
Instant Review
Interval Shoot
Fast Fwd Movie
3D Mode
Memory
Sharpness
Saturation
Contrast
USER
memo
Appendix
144
320×240 • Settings for items marked with an [] can be changed on the
menu screen, but the change will not be reflected in camera
operations.
• In
mode, only the settings marked with an [] can be
changed in the registered mode.
e06_kb338_123_157_41e.qk 3/17/03 4:11 PM Page 145
Messages
Messages such as the following may be displayed on the LCD monitor
during camera operation.
The SD Memory Card/MultiMediaCard
memory is full and no more images and
sound can be saved. Insert a new SD
Memory Card/MultiMediaCard or delete
unwanted images. (p.16, p.96)
Change the quality/size and try again. (p.43,
p.44)
No image & sound
There are no images and sound on the SD
Memory Card/MultiMediaCard to playback.
Camera can not display
this image.
You are trying to play back an image in a
format not supported by this camera. You
may be able to display it on another brand
of camera or PC.
No card in camera.
There is no SD Memory
Card/MultiMediaCard in the camera. (p.16)
Battery depleted.
The battery is exhausted. Charge the NiMH
batteries using a battery charger or replace
with new batteries. (p.12, p.13)
Memory card error.
Shooting and playback are impossible due
to a problem with SD Memory Card/
MultiMediaCard. Try displaying on a PC.
This card is not formatted.
The SD Memory Card/MultiMediaCard you have inserted is unformatted or has been formatted on a PC or
other device and is not compatible with the camera.
Image recording.
The image/voice recording is being recorded
on the SD Memory Card/MultiMediaCard.
Data being recorded.
The movie picture is being recorded on the
SD Memory Card/MultiMediaCard.
Changing setting
The protect setting or DPOF setting is
being changed.
Formatting
The SD Memory Card/MultiMediaCard is being
formatted.
Appendix
Memory card full
145
e06_kb338_123_157_41e.qk 3/17/03 4:11 PM Page 146
Appendix
146
Deleting
The image is being deleted.
Image folder could not be
created.
The largest file number is assigned to an
image and no more images can be saved.
Insert a new SD Memory
Card/MultiMediaCard or format the SD
Memory Card/MultiMediaCard. (p.126)
This card is not formatted.
The SD Memory Card/MultiMedia Card you
have inserted is unformatted, or has been
formatted on a PC or other device and is
not compatible with this camera. (p.126)
Compression error
Compression of the image you captured
has failed. Change the recorded pixels or
quality levels, and take a picture again.
Data being recorded
The movie picture is being recorded.
Image protected
The image you are trying to delete is a protected image. (p.99)
Alarm set
The alarm has been enabled.
e06_kb338_123_157_41e.qk 3/17/03 4:11 PM Page 147
Troubleshooting
Problem
Power will not
come on
No image on the
LCD monitor
Shutter will not
be released
Remedy
Check battery is installed.
If not, install battery.
Battery is installed
incorrectly
Check orientation of battery.
Reinsert battery with the label
towards front of camera. (p.13)
Battery power is low
Insert a charged battery or use the
AC adapter.
LCD monitor is set to
OFF
Press Display button to turn LCD
monitor on. (p.38)
Connected to PC by
USB cable.
When connecting to PC, LCD
monitor is always On.
Camera is connected
to TV
LCD monitor remains off while
camera is connected to TV.
Image is displayed but
is hard to see
Image on LCD monitor may be
hard to see when taking pictures
outside in sunlight.
Flash is charging
When flash lamp blinks red, flash
is charging and no pictures can be
taken. Lamp lights red when
charging is completed.
No available space on
SD Memory
Card/MultiMediaCard
Insert SD Memory Card/
MultiMediaCard with available
space or delete unwanted images.
(p.16, 96)
Recording
Wait until recording is finished.
Super Macro mode has
been set.
The zoom is disabled in this
modes.
Appendix
Zoom does not
work
Cause
Battery is not installed
147
e06_kb338_123_157_41e.qk 3/17/03 4:11 PM Page 148
Problem
Subject is not in
focus
Picture is dark
Appendix
148
Cause
Remedy
Subject difficult to
focus on
Subjects difficult to focus on using
autofocus: objects with little contrast (blue sky, white walls, etc.),
dark objects, finely patterned
objects, fast-moving objects,
scenery through window or net,
etc. Lock focus on another object
located at same distance (press
shutter release button halfway),
then aim at target and press shutter release button fully.
Subject is not in focusing area
Position subject in AF frame
(focusing area) in middle of LCD
monitor. If the subject is outside
the focusing area, aim the camera
at the subject and lock focus
(press shutter release button
halfway), then compose picture
and press the shutter release button fully.
Subject is too close
Set focus mode on
Focus mode is set on
Normal pictures will be out of
focus if taken with focus mode set
on .
Subject is too far away
in a dark environment,
such as a night scene.
Picture becomes dark if subject is
too far away. Take picture within
range of flash.
Background is dark
When taking a picture of a person
against dark background, such as
night scene, the person may
appear dark if the flash does not
reach background even with correct exposure. Set to
mode to
ensure both person and background are clear. (p.59)
. (p.40)
e06_kb338_123_157_41e.qk 3/17/03 4:11 PM Page 149
Problem
Flash does not
fire
Cause
Flash mode is set to
Off
The Capture mode is
set to
, super
macro, continuous
shooting or infinitylandscape mode, or
the Picture mode is
set to Fireworks
mode.
Remedy
Set to Auto or
. (p.42)
Flash will not fire in these modes.
Appendix
149
e06_kb338_123_157_41e.qk 3/17/03 4:11 PM Page 150
Optional Accessories
A number of dedicated accessories are available for this camera.
•
•
•
•
•
•
•
•
•
Appendix
150
Lithium-ion battery D-LI7 (Rechargeable) (included)
Battery charger D-BC7 (included)
AC adapter D-AC7
AC Plug Cord (included)
D-CO2A Australia
D-CO2B United Kingdom
D-CO2E Europe
D-CO2H Hong Kong
D-CO2J Japan
D-CO2K Korea
D-CO2U North America, Canada
USB Cable I-USB7 (included)
AV Cable I-AVC7 (included)
Camera Case O-CC7
Strap O-ST5 (included)
Remote Control Unit F
e06_kb338_123_157_41e.qk 3/17/03 4:11 PM Page 151
WARRANTY POLICY
All Pentax cameras purchased through authorized bona fide photographic distribution channels are guaranteed against defects of material or workmanship for
a period of twelve months from date of purchase. Service will be rendered, and
defective parts will be replaced without cost to you within that period, provided
the equipment does not show evidence of impact, sand or liquid damage, mishandling, tampering, battery or chemical corrosion, operation contrary to operating instructions, or modification by an unauthorized repair shop. The manufacturer or its authorized representatives shall not be liable for any repair or alterations
except those made with its written consent and shall not be liable for damages
from delay or loss of use or from other indirect or consequential damages of any
kind, whether caused by defective material or workmanship or otherwise; and it
is expressly agreed that the liability of the manufacturer or its representatives
under all guarantees or warranties, whether expressed or implied, is strictly limited to the replacement of parts as hereinbefore provided. No refunds will be
made on repairs by non-authorized Pentax service facilities.
Appendix
Procedure During 12-month Warranty Period
Any Pentax which proves defective during the 12-month warranty period should
be returned to the dealer from whom you purchased the equipment or to the
manufacturer. If there is no representatives of the manufacturer in your country,
send the equipment to the manufacturer, with postage prepaid. In this case, it
will take a considerable length of time before the equipment can be returned to
you owing to the complicated customs procedures required. If the equipment is
covered by warranty, repairs will be made and parts replaced free of charge,
and the equipment will be returned to you upon completion of servicing. If the
equipment is not covered by warranty, regular charges of the manufacturer or of
its representatives will apply. Shipping charges are to be borne by the owner. If
your Pentax was purchased outside of the country where you wish to have it
serviced during the warranty period, regular handling and servicing fees may be
charged by the manufacturer's representatives in that country. Notwithstanding
this, your Pentax returned to the manufacturer will be serviced free of charge
according to this procedure and warranty policy. In any case, however, shipping
charges and customs clearance fees to be borne by the sender. To prove the
date of your purchase when required, please keep the receipt or bills covering
the purchase of your equipment for at least a year. Before sending your equipment for servicing, please make sure that you are sending it to the manufacturer's authorized representatives or their approved repair shops, unless you are
sending it directly to the manufacturer. Always obtain a quotation for the service
charge, and only after you accept the quoted service charge, instruct the service
station to proceed with the servicing.
• This warranty policy does not affect the customer's statutory rights.
• The local warranty policies available from Pentax distributors in some
countries can supersede this warranty policy. Therefore, we recommend
that you review the warranty card supplied with your product at the time of
purchase, or contact the PENTAX distributor in your country for more
information and to receive a copy of the warranty policy.
151
e06_kb338_123_157_41e.qk 3/17/03 4:11 PM Page 152
Main Specifications
Type
Fully automatic compact-type digital still camera with built-in
zoom lens
Effective Pixels
5.0 megapixels
Sensor
5.25 megapixels (total pixels) 1/1.8 inch interline transfer CCD with
a primary color filter
Recorded Pixels
Still
Movie
2592 × 1944 pixels, 2048 × 1536 pixels, 1600 × 1200 pixels,
1024 × 768 pixels, 640 × 480 pixels
320 × 240 pixels
Sensitivity
Auto, manual (equivalent to ISO 64, 100, 200, 400)
File Format
Still
JPEG (Exif2.2), TIFF, DCF, DPOF, PRINT Image Matching II
Movie Mov (Quick Time Motion), 15fps
Quality Level
Storage Medium
“TIFF”, “Good”, “Better”, “Best”
SD Memory Card, MultiMediaCard
Image Storage Capacity
Quality levels
Recorded pixels
Best
()
Better
()
Good
()
2592 × 1944
Approx. 4
Approx. 8
Approx. 14
2048 × 1536
Approx. 7
Approx. 12
Approx. 18
1600 × 1200
Approx. 11
Approx. 20
Approx. 27
1024 × 768
Approx. 25
Approx. 45
Approx. 56
640 × 480
Approx. 53
Approx. 82
Approx. 100
Movie images
(320 × 240)
Voice
recording
Approx. 40
Approx. 30
Exposure capacity when using a 16MB SD Memory Card
Auto, Daylight, Shade, Tungsten Light, Fluorescent Light (W),
Fluorescent Light (N), Fluorescent Light (D), Manual
Lens
Focal Length
Digital Zoom
Capture mode
Max. 4× (Combines with 5× optical zoom to give
zoom magnification equivalent to 20×)
Viewfinder
Type
Real-image zoom viewfinder
(Diopter adjustment in the range of –3 to +1m–1)
Wide 0.37×, Tele 1.66×
Appendix
White Balance
7.8 mm – 39 mm (Equivalent to 37.5 mm –
187.5 mm in 35 mm format)
Aperture
f/2.8 – f/4.6
Lens Composition 9 elements in 7 groups (two aspherical elements)
Zoom type
Electrically driven
33.7 mm × 24.7 mm (screen is filled) (using super
Picture Range
macro mode or manual focus at max, WIDE position)
Lens Barrier
Electrically driven
Magnification
152
e06_kb338_123_157_41e.qk 3/17/03 4:11 PM Page 153
LCD Monitor
1.5 inch low-sound polysilicon TFT color LCD monitor (113
Kilopixels) (with backlight)
Playback
Single-frame, 9-frame index, enlargement (max. 8×), scroll, slideshow,
Function
movie playback, voice playback, histogram display, trimming, resize
Focusing System Type
TTL contrast detection system by sensor with
external passive sensor
Focusing Range Normal: 0.6 m (1.97 ft) to infinity (full zoom range)
(From lens front)
Macro: 0.15 m (0.50 ft) – 0.65 m (2.13 ft) (full zoom range)
Super macro: 0.02 m (0.8 in.) – 0.65 m (2.13 ft) (Wide only)
Landscape:
Infinity (full zoom range)
Focus Lock
By half-pressing shutter release button
Manual Focus
0.15 m (0.50 ft) to infinity (full zoom range), 0.02 m (0.8 in.) to infinity (Wide only)
Exposure
Mechanism
AE Metering
Exposure Compensation
Movie
Auto Bracket
Exposure Modes
Shutter
Type
Speed
Flash
Type
Flash Modes
Drive Modes
Self-timer
TTL metering by sensor (Multi-segment,
Center-weighted, Spot)
±2 EV (Set in 1/3 EV steps)
Recording time approx. 1 sec – max. 10 min.
Possible
Program, Av, Tv, M, PICT, Movie, Panorama
Assist, 3D, Digital Filter, USER, Voice Recording
Electronic/mechanical shutter
Approx. 1/4000 sec. – 4 sec.
Auto flash with red-eye reduction function
Auto, Flash Off, Flash On, Auto + Red-eye
reduction, Flash On + Red-eye Reduction
Working Range Wide: Approx. 0.4 m – 5.2 m (1.31 ft – 17.1 ft)
(ISO/AUTO)
Tele: Approx. 0.15 m – 3.2 m (0.50 ft – 10.5 ft)
Single-frame, Self-timer, Remote Control after 3 Seconds, Remote Control, Continuous, Interval, Multiple Exposure
Electronic control type, delay time: approx. 10 sec.
Remote Control Unit Pentax Remote Control Unit F (optional)
Exposure 3 seconds after receipt of signal or instant exposure
Time function
World Time setting for 62 cities (28 time zones)
Rechargeable lithium-ion battery D-LI7, AC adapter (optional)
Approx. 400 with 50% of shooting uses flash, LCD monitor ON in
accordance with Pentax measuring conditions.
In/Out Port
USB/AV terminal (PC communication type USB1.1), external power
supply terminal
Appendix
Power Supply
Battery life w/fully
charged
Video Output Format NTSC, PAL
100 (W) × 59 (H) × 39.5 (D) mm (excluding operating members)
Size
Weight
205 g (excluding battery and SD Memory Card/MultiMediaCard)
Weight when shooting 250 g (including battery and SD Memory Card/MultiMediaCard)
Accessories
Rechargeable lithium-ion battery, battery charger, USB cable, AV cable,
3D image viewer, software (CD-ROM), strap, operating manual
153
e06_kb338_123_157_41e.qk 3/17/03 4:11 PM Page 154
For customers in USA
STATEMENT OF FCC COMPLIANCE
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Changes or modifications not approved by the party responsible for
compliance could void the user's authority to operate the equipment.
This equipment has been tested and found comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
* Consult the dealer or an experienced radio/TV technician for help.
For customers in Canada
This Class B digital apparatus meets all requirements of the
Canadian Interference - Causing Equipment Regulations.
Appendix
Pour les utilisateurs au Canada
Cet apareil numérique de la classe B respecte toutes les exigences du
Règlement sur le matériel brouilleur du Canada.
The CE Mark is a Directive conformity mark of the European
Community.
The CE Mark is a Directive conformity mark of the European
Community.
154
e06_kb338_123_157_41e.qk 3/17/03 4:11 PM Page 155
Declaration of Conformity
According to 47CFR, Parts 2 and 15 for
Class B Personal Computers and Peripherals
We:
PENTAX U.S.A., Inc.
Located at: 35 Inverness Drive East
Englewood, Colorado 80112 USA
Phone: 303-799-8000 FAX: 303-790-1131
Declare under sole responsibility that the product identified herein, complies with 47CFR Parts 2 and 15 of the
FCC rules as a Class B digital device. Each product marketed, is identical to the representative unit tested and
found to be compliant with the standards. Records maintained continue to reflect the equipment being produced
can be expected to be within the variation accepted, due
to quantity production and testing on the statistical basis
as required by 47CFR §2.909. Operation is subject to the
following two conditions: (1) This device may not cause
harmful interference, and (2) This device must accept
any interference received, including interference that may
cause undesired operation. The above named party is
responsible for ensuring that the equipment complies
with the standards of 47CFR §15.101 to §15.109.
Model Number: Optio 550
Appendix
Product Name: PENTAX Digital Still Camera
Contact person: Customer Service Manager
Date and Place: February, 2003, Colorado
155
e06_kb338_123_157_41e.qk 3/17/03 4:11 PM Page 156
MEMO
e06_kb338_123_157_41e.qk 3/17/03 4:11 PM Page 157
e07_kb338_OBC_41e.qk 3/17/03 4:12 PM Page 158
2-36-9,Maeno-cho, Itabashi-ku, Tokyo 174-8639,
JAPAN
(http://www.pentax.co.jp/)
PENTAX Europe GmbH (European Headquarters)
Julius-Vosseler-Strasse, 104, 22527 Hamburg,
GERMANY
(HQ - http://www.pentaxeurope.com)
(Germany - http://www.pentax.de)
PENTAX U.K. Limited
Pentax House, Heron Drive, Langley, Slough, Berks
SL3 8PN, U.K.
(http://www.pentax.co.uk)
PENTAX France S.A.S.
12/14, rue Jean Poulmarch, 95106 Argenteuil Cedex,
FRANCE
PENTAX Benelux B.V.
(for Netherlands)
Spinveld 25, 4815 HR Breda, NETHERLANDS
(http://www.pentax.nl)
(for Belgium & Luxembourg)
Weiveldlaan 3-5, 1930 Zaventem, BELGIUM
(http://www.pentax.be)
PENTAX (Schweiz) AG
Widenholzstrasse 1 Postfach 367 8305 Dietlikon,
SWITZERLAND (http://www.pentax.ch)
PENTAX Scandinavia AB P.O. Box 650, 75127 Uppsala, SWEDEN
(http://www.pentax.se)
PENTAX U.S.A., Inc.
35 Inverness Drive East, Englewood, Colorado
80112, U.S.A.
(http://www.pentax.com)
PENTAX Canada Inc.
3131 Universal Drive, Mississauga, Ontario L4X 2E5,
CANADA
(http://www.pentaxcanada.ca)
PENTAX Corporation
http://www.digital.pentax.co.jp
• Printed on recycled paper
• Specifications and external dimensions are subject to change without notice.
57227
Copyright © PENTAX Corporation 2003
02-200304 Printed in Japan
">