advertisement
Camera User Guide
ENGLISH
•
Make sure you read this guide, including the “Safety
Precautions” ( = 6 ) section, before using the camera.
• Reading this guide will help you learn to use the camera properly.
• Store this guide safely so that you can use it in the future.
• Click the buttons in the lower right to access other pages.
: Next page
: Previous page
: Page before you clicked a link
• To jump to the beginning of a chapter, click the chapter title at right.
From chapter title pages, you can access topics by clicking their titles.
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
© CANON INC. 2016 CT0-D050-000-F101-B 1
Package Contents
Before use, make sure the following items are included in the package.
If anything is missing, contact your camera retailer.
Camera Battery Pack
NB-11L*
Battery Charger
CB-2LF/CB-2LFE
Printed Matter
Wrist Strap
* Do not peel off the adhesive covering from a battery pack.
• A memory card is not included (
).
Compatible Memory Cards
The following memory cards (sold separately) can be used, regardless of capacity.
• SD memory cards*
• SDHC memory cards*
• SDXC memory cards*
* Cards conforming to SD standards. However, not all memory cards have been verified to work with the camera.
Preliminary Notes and Legal
Information
• Take and review some test shots initially to make sure the images were recorded correctly. Please note that Canon Inc., its subsidiaries and affiliates, and its distributors are not liable for any consequential damages arising from any malfunction of a camera or accessory, including memory cards, that result in the failure of an image to be recorded or to be recorded in a way that is machine readable.
• Images recorded by the camera shall be for personal use. Refrain from unauthorized recording that infringes on copyright law, and note that even for personal use, photography may contravene copyright or other legal rights at some performances or exhibitions, or in some commercial settings.
• The camera warranty is valid only in the area of purchase. In case of camera problems while abroad, return to the area of purchase before contacting a Canon Customer Support Help Desk.
• Although the screen (monitor) is produced under extremely highprecision manufacturing conditions and more than 99.99% of the pixels meet design specifications, in rare cases some pixels may be defective or may appear as red or black dots. This does not indicate camera damage or affect recorded images.
• When the camera is used over an extended period, it may become warm.
This does not indicate damage.
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
2
Part Names and Conventions in This Guide
Microphone
Lens
Speaker
Zoom lever
Shooting: [ (telephoto)] /
[ (wide angle)]
Playback: [ (magnify)] /
[ (index)]
Shutter button
Lamp
Power button
Flash
(N-Mark)*
Tripod socket
Memory card/battery cover
Strap mount
* Used with NFC features (
• Shooting modes and on-screen icons and text are indicated in brackets.
• : Important information you should know
• : Notes and tips for expert camera use
• =xx : Pages with related information (in this example, “xx” represents a page number)
• The tabs shown above titles indicate whether the function is used for still images, movies, or both.
Still Images
: Indicates that the function is used when shooting or
Movies viewing still images.
: Indicates that the function is used when shooting or viewing movies.
Screen (monitor)
AV OUT (Audio/video output) /
DIGITAL terminal
[ (Playback)] button
[ (Auto)] /
[ (Single-image erase)] /
Up button
[ (Auto zoom)] / Left button
Indicator
[ (Wi-Fi)] button
Movie button
FUNC. (Function) / SET button
[ (Flash)] / Right button
[ (Information)] / Down button
[ ] button
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
• In this guide, icons are used to represent the corresponding camera buttons on which they appear, or which they resemble.
• The following camera buttons and controls are represented by icons.
[ ] Up button on back
[ ] Left button on back
[ ] Right button on back
[ ] Down button on back
• Instructions in this guide apply to the camera under default settings.
• For convenience, all supported memory cards are simply referred to as the “memory card”.
3
Table of Contents
Package Contents .........................
Compatible Memory Cards ............
Information .....................................
Part Names and Conventions in This Guide ..................................
Table of Contents ...........................
Common Camera Operations ........
Safety Precautions .........................
Basic Guide ......................
Initial Preparations .......................
Trying the Camera Out ................
Camera Basics ...........................
On/Off ..........................................
Shutter Button ..............................
Shooting Display Options ............
Using the FUNC. Menu ................
Using the Menu Screen ...............
On-Screen Keyboard ...................
Indicator Display ..........................
Auto Mode ..................................
Shooting with Camera-Determined
Settings ........................................
Common, Convenient Features ...
Image Customization Features ....
Operation .....................................
Other Shooting Modes ..............
Specific Scenes ...........................
Applying Special Effects ..............
Purposes ......................................
P Mode ........................................
([P] Mode) ....................................
Image Brightness (Exposure) ......
Adjusting White Balance ..............
Shooting Range and Focusing ....
Flash ............................................
Other Settings ..............................
Playback Mode...........................
Viewing ........................................
Browsing and Filtering Images ....
Image Viewing Options ................
Protecting Images ........................
Erasing Images ............................
Rotating Images ...........................
Tagging Images as Favorites .......
Editing Still Images ......................
Wi-Fi Functions ..........................
Available Wi-Fi Features ..............
Sending Images to a Smartphone ..............................
Saving Images to a Computer .....
Sending Images to a Registered
Web Service .................................
Printing Images Wirelessly from a Connected Printer .....................
Camera ........................................
Image Sending Options ...............
(Image Sync)................................
Camera Images and Control the Camera ..................................
Settings ........................................
Setting Menu ..............................
Functions .....................................
Accessories .............................
System Map ...............................
Optional Accessories .................
Using Optional Accessories .......
Using the Software ....................
Printing Images ..........................
Appendix ..................................
Troubleshooting .........................
On-Screen Messages ................
On-Screen Information ..............
Functions and Menu Tables .......
Handling Precautions .................
Specifications .............................
Index ..........................................
Precautions ................................
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
4
Common Camera Operations
Shoot
z z
Shooting people well
Portraits
)
Matching specific scenes
Low Light
)
Applying special effects
Fireworks
(
Vivid Colors
Miniature Effect
Poster Effect
)
Toy Camera Effect
)
Fish-Eye Effect
)
Monochrome
) z z
z z
z z
z z
View
z z
z z
z z
z z
z z
z z
Record/View Movies
z z
z z
z z
Save
z z
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
5
Safety Precautions
• Before using the product, ensure that you read the safety precautions described below. Always ensure that the product is used correctly.
• The safety precautions noted here are intended to prevent you and other persons from being injured or incurring property damage.
• Be sure to also check the guides included with any separately sold accessories you use.
Warning
Denotes the possibility of serious injury or death.
• Do not trigger the flash in close proximity to people’s eyes.
Exposure to the intense light produced by the flash could damage eyesight.
In particular, remain at least 1 meter (3.3 feet) away from infants when using the flash.
• Store this equipment out of the reach of children and infants.
A strap wound around a child’s neck may result in asphyxiation.
If your product uses a power cord, mistakenly winding the cord around a child’s neck may result in asphyxiation.
• Use only recommended power sources.
• Do not disassemble, alter, or apply heat to the product.
• Avoid dropping or subjecting the product to severe impacts.
• Do not touch the interior of the product if it is broken, such as when dropped.
• Stop using the product immediately if it emits smoke or a strange smell, or otherwise behaves abnormally.
• Do not use organic solvents such as alcohol, benzine, or thinner to clean the product.
• Avoid contact with liquid, and do not allow liquid or foreign objects inside.
This could result in electrical shock or fire.
If the product gets wet, or if liquid or foreign objects get inside, remove the battery pack/batteries or unplug immediately.
• If your model has a viewfinder or interchangeable lens, do not look through the viewfinder or lens at bright light sources (such as the sun on a clear day, or a bright artificial light source).
This may damage your eyesight.
• If your model has an interchangeable lens, do not leave the lens (or the camera with the lens attached) in the sun without the lens cap on.
This could result in a fire.
• Do not touch the product during thunderstorms if it is plugged in.
This could result in electrical shock or fire. Immediately stop using the product and distance yourself from it.
• Use only the recommended battery pack/batteries.
• Do not place the battery pack/batteries near or in direct flame.
This may cause the battery pack/batteries to explode or leak, resulting in electrical shock, fire, or injuries. If leaking battery electrolyte comes into contact with eyes, mouth, skin, or clothing, immediately flush with water.
• If the product uses a battery charger, note the following precautions.
- Remove the plug periodically and, using a dry cloth, wipe away any dust and dirt that has collected on the plug, the exterior of the power outlet, and the surrounding area.
- Do not insert or remove the plug with wet hands.
- Do not use the equipment in a manner that exceeds the rated capacity of the electrical outlet or wiring accessories. Do not use if the plug is damaged or not fully inserted in the outlet.
- Do not allow dust or metal objects (such as pins or keys) to contact the terminals or plug.
- Do not cut, damage, alter, or place heavy items on the power cord, if your product uses one.
This could result in electrical shock or fire.
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
6
• Turn the camera off in places where camera use is prohibited.
The electromagnetic waves emitted by the camera may interfere with the operation of electronic instruments and other devices. Exercise adequate caution when using the product in places where use of electronic devices is restricted, such as inside airplanes and medical facilities.
• Do not allow the camera to maintain contact with skin for extended periods.
Even if the camera does not feel hot, this may cause low-temperature burns, manifested in redness of the skin or blistering. Use a tripod in hot places, or if you have poor circulation or insensitive skin.
Caution
Denotes the possibility of injury.
• When carrying the product by the strap, be careful not to bang it, subject it to strong impacts or shocks, or let it get caught on other objects.
• Be careful not to bump or push strongly on the lens.
This could lead to injury or damage the camera.
• Be careful not to subject the screen to strong impacts.
If the screen cracks, injury may result from the broken fragments.
• When using the flash, be careful not to cover it with your fingers or clothing.
This could result in burns or damage to the flash.
• Avoid using, placing, or storing the product in the following places:
- Places subject to direct sunlight
- Places subject to temperatures above 40 °C (104 °F)
- Humid or dusty places
These could cause leakage, overheating, or an explosion of the battery pack/batteries, resulting in electrical shock, fire, burns, or other injuries.
Overheating and damage may result in electrical shock, fire, burns, or other injuries.
• The slideshow transition effects may cause discomfort when viewed for prolonged periods.
• When using optional lenses, lens filters, or filter adapters (if applicable), be sure to attach these accessories firmly.
If the lens accessory becomes loose and falls off, it may crack, and the shards of glass may lead to cuts.
• On products that raise and lower the flash automatically, make sure to avoid pinching your fingers with the lowering flash.
This could result in injury.
Caution
Denotes the possibility of property damage.
• Do not aim the camera at intense light sources, such as the sun on a clear day or an intense artificial light source.
Doing so may damage the image sensor or other internal components.
• When using the camera on a sandy beach or at a windy location, be careful not to allow dust or sand to enter the camera.
• On products that raise and lower the flash automatically, do not push the flash down or pry it open.
This may cause the product to malfunction.
• Wipe off any dust, grime, or other foreign matter on the flash with a cotton swab or cloth.
The heat emitted from the flash may cause foreign matter to smoke or the product to malfunction.
• Remove and store the battery pack/batteries when you are not using the product.
Any battery leakage that occurs may cause product damage.
• Before you discard the battery pack/batteries, cover the terminals with tape or other insulators.
Contacting other metal materials may lead to fire or explosions.
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
7
• Unplug any battery charger used with the product when not in use.
Do not cover with a cloth or other objects when in use.
Leaving the unit plugged in for a long period of time may cause it to overheat and distort, resulting in fire.
• Do not leave any dedicated battery packs near pets.
Pets biting the battery pack could cause leakage, overheating, or explosion, resulting in product damage or fire.
• If your product uses multiple batteries, do not use batteries that have different levels of charge together, and do not use old and new batteries together. Do not insert the batteries with the + and – terminals reversed.
This may cause the product to malfunction.
• Do not sit down with the camera in your pant pocket.
Doing so may cause malfunctions or damage the screen.
• When putting the camera in your bag, ensure that hard objects do not come into contact with the screen. Also close the screen (so that it faces the body), if your product’s screen closes.
• Do not attach any hard objects to the product.
Doing so may cause malfunctions or damage the screen.
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
8
Basic Guide
Basic information and instructions, from initial preparations to shooting and playback
Initial Preparations ...........................................
Attaching the Strap ................................................
Holding the Camera ..............................................
Charging the Battery Pack ....................................
Inserting the Battery Pack and Memory Card .......
Setting the Date and Time .....................................
Display Language .................................................
Trying the Camera Out .....................................
Shooting (Smart Auto) ...........................................
Viewing ..................................................................
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
9
Initial Preparations
Prepare for shooting as follows.
Attaching the Strap
z z strap mount ( ), and then pull the other end of the strap through the loop on the threaded end ( ).
Holding the Camera
z z z z your body and hold the camera securely to prevent it from moving. Do not rest your fingers on the flash.
g
Charging the Battery Pack
Before use, charge the battery pack with the included charger. Be sure to charge the battery pack initially, because the camera is not sold with the battery pack charged.
1
Insert the battery pack.
z z pack and charger, insert the battery pack by pushing it in ( ) and down ( ).
CB-2LF
CB-2LFE
2
Charge the battery pack.
z z the charger into a power outlet ( ).
z z charger, then plug the other end into a power outlet.
z z charging begins.
z z green.
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
3
Remove the battery pack.
z z remove the battery pack by pushing it in
( ) and up ( ).
10
• To protect the battery pack and keep it in optimal condition, do not charge it continuously for more than 24 hours.
• For battery chargers that use a power cord, do not attach the charger or cord to other objects. Doing so could result in malfunction or damage to the product.
• For details on charging time and the number of shots and recording time
possible with a fully charged battery pack, see “Number of Shots/Recording
Time, Playback Time” ( = 137 ).
• Charged battery packs gradually lose their charge, even when they are not used. Charge the battery pack on (or immediately before) the day of use.
• The charger can be used in areas with 100 – 240 V AC power (50/60 Hz). For power outlets in a different format, use a commercially available adapter for the plug. Never use an electrical transformer designed for traveling, which may damage the battery pack.
Inserting the Battery Pack and Memory Card
Insert the included battery pack and a memory card (sold separately).
Note that before using a memory card that is new or has been formatted in another device, you should format the memory card with this camera
(
).
1
Open the cover.
z z
Terminals Battery
Lock
Label
2
Insert the battery pack.
z z direction of the arrow, insert the battery pack as shown and push it in until it clicks into the locked position.
3
Check your card’s write-protect switch and insert the memory card.
z z cards with a write-protect switch when the switch is in the locked position. Slide the switch to the unlocked position.
z z z until it clicks into the locked position.
z right way when you insert it. Inserting memory cards facing the wrong way may damage the camera.
4
Close the cover.
z z you slide it, until it clicks into the closed position ( ).
z z inserted the battery pack facing the right way in step 2.
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
11
• For guidelines on how many shots or hours of recording can be saved on one
memory card, see “Number of Shots per Memory Card” ( = 137 ).
Removing the Battery Pack and Memory Card
Remove the battery pack.
z z lock in the direction of the arrow.
z z
Remove the memory card.
z z and then slowly release it.
z z
Setting the Date and Time
Set the current date and time correctly as follows if the [Date/Time] screen is displayed when you turn the camera on. Information you specify this way is recorded in image properties when you shoot, and it is used when you manage images by shooting date or print images showing the date.
You can also add a date stamp to shots, if you wish (
1
Turn the camera on.
z z z z
2
Set the date and time.
z z z item.
z date and time.
z z
3
Specify your home time zone.
z z home time zone.
4
Finish the setup process.
z z setting. The setting screen is no longer displayed.
z z button.
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
• Unless you set the date, time, and home time zone, the [Date/Time] screen will be displayed each time you turn the camera on. Specify the correct information.
• To set daylight saving time (1 hour ahead), choose [ ] in step 2 and then choose [ ] by pressing the [ ][ ] buttons.
12
Changing the Date and Time
Adjust the date and time as follows.
1
Access the menu screen.
z z ] button.
2
Choose [Date/Time].
z z tab.
z z
[Date/Time], and then press the [ ] button.
3
Change the date and time.
z z
Time” ( = 12 ) to adjust the settings.
z z menu screen.
] button to close the
• Date/time settings can be retained for about 3 weeks by the camera’s built-in date/time battery (backup battery) after the battery pack is removed.
• The date/time battery will be charged in about 4 hours once you insert a charged battery pack, even if the camera is left off.
• Once the date/time battery is depleted, the [Date/Time] screen will be displayed when you turn the camera on. Set the correct date and time as
described in “Setting the Date and Time” ( = 12 ).
Display Language
Change the display language as needed.
1
Enter Playback mode.
z z
2
Access the setting screen.
z z press the [ ] button.
3
Set the display language.
z z a language, and then press the [ ] button.
z z the setting screen is no longer displayed.
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
• You can also change the display language by pressing the [ and choosing [Language ] on the [ ] tab.
] button
13
Trying the Camera Out
Still Images Movies
Follow these instructions to turn the camera on, shoot still images or movies, and then view them.
Shooting (Smart Auto)
For fully automatic selection of the optimal settings for specific scenes, simply let the camera determine the subject and shooting conditions.
1
Turn the camera on.
z z z z
2
Enter [ ] mode.
z z z
[ z
] is displayed.
Aim the camera at the subject. The camera will make a slight clicking noise as it determines the scene.
z z stabilization mode are displayed in the upper right of the screen.
z z subjects indicate that they are in focus.
3
Compose the shot.
z z the zoom lever toward [ ] (telephoto), and to zoom away from the subject, move it toward [ ] (wide angle).
4
Shoot.
Shooting Still Images
Focus.
z z down. The camera beeps twice after focusing, and AF frames are displayed to indicate image areas in focus.
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
Shoot.
z z down.
z z is played, and in low-light conditions, the flash fires automatically.
z z sound ends.
z z revert to the shooting screen.
14
Elapsed Time
Recording Movies
Start recording.
z z beeps once as recording begins, and
[ Rec] is displayed with the elapsed time.
z z bottom edges of the screen, and the subject is slightly enlarged. The black bars indicate image areas not recorded.
z z faces indicate that they are in focus.
z z off the movie button.
Finish recording.
z z recording. The camera beeps twice as recording stops.
Viewing
After shooting images or movies, you can view them on the screen as follows.
1
Enter Playback mode.
z z z z
2
Choose images.
z z button. To view the next image, press the
[ ] button.
z z browse through images quickly.
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index z z
To play movies, go to step 3.
] icon.
15
3
Play movies.
z z buttons to choose [ ], and then press the
[ ] button again.
z z is finished, [ ] is displayed.
z z buttons during playback.
• To switch to Shooting mode from Playback mode, press the shutter button halfway.
Erasing Images
You can choose and erase unneeded images one by one. Be careful when erasing images, because they cannot be recovered.
1
Choose an image to erase.
z z
2
Erase the image.
z z z z
[ ][ ] buttons to choose [Erase], and then press the [ ] button.
z z z z buttons to choose [Cancel], and then press the [ ] button.
• You can choose multiple images to erase at once (
).
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
16
Advanced Guide
Camera Basics
Other basic operations and more ways to enjoy your camera, including shooting and playback options
On/Off ................................................................
Power-Saving Features (Auto Power Down) ........
Shutter Button ..................................................
Shooting Display Options ...............................
Using the FUNC. Menu ....................................
Using the Menu Screen ...................................
On-Screen Keyboard .......................................
Indicator Display ..............................................
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
17
On/Off
Shooting Mode
z z camera on and prepare for shooting.
z z button again.
Playback Mode
z z z on and view your shots.
z button again.
• To switch to Playback mode from Shooting mode, press the [ ] button.
• To switch to Shooting mode from Playback mode, press the shutter button
• The lens will be retracted after about one minute once the camera is in
Playback mode. You can turn the camera off when the lens is retracted by pressing the [ ] button.
Power-Saving Features (Auto Power Down)
As a way to conserve battery power, the camera automatically deactivates the screen (Display Off) and then turns itself off after a specific period of inactivity.
Power Saving in Shooting Mode
The screen is automatically deactivated after about one minute of inactivity.
In about two more minutes, the lens is retracted and the camera turns itself off. To activate the screen and prepare for shooting when the screen is off
but the lens is still out, press the shutter button halfway ( = 19 ).
Power Saving in Playback Mode
The camera turns itself off automatically after about five minutes of inactivity.
• You can deactivate Auto Power Down and adjust the timing of Display Off, if
• Power saving is not active while the camera is connected to a computer
(
).
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
18
Shutter Button
To ensure your shots are in focus, always begin by holding the shutter button halfway down, and once the subject is in focus, press the button all the way down to shoot.
In this manual, shutter button operations are described as pressing the button halfway or all the way down.
1
Press halfway. (Press lightly to focus.)
z z camera beeps twice, and frames are displayed around image areas in focus.
2
Press all the way down. (From the halfway position, press fully to shoot.)
z z is played.
z z sound ends.
• Images may be out of focus if you shoot without initially pressing the shutter button halfway.
• Length of shutter sound playback varies depending on the time required for the shot. It may take longer in some shooting scenes, and images will be blurry if you move the camera (or the subject moves) before the shutter sound ends.
Shooting Display Options
Press the [ ] button to view other information on the screen, or to hide
the information. For details on the information displayed, see “On-Screen
Information is displayed No information is displayed
• Screen brightness is automatically increased by the night view function when you are shooting under low light, making it easier to check how shots are composed. However, on-screen image brightness may not match the brightness of your shots. Note that any on-screen image distortion or jerky subject motion will not affect recorded images.
•
For playback display options, see “Switching Display Modes” ( = 57 ).
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
19
Using the FUNC. Menu
Configure commonly used functions through the FUNC. menu as follows.
Note that menu items and options vary depending on the shooting mode
(
–
).
1
Access the FUNC. menu.
z z
Options
Menu Items
2
Choose a menu item.
z z menu item, and then press the [ ] or [ ] button.
z z can be specified simply by pressing the
[ ] or [ ] button, or another screen is displayed for configuring the function.
3
Choose an option.
z z z option.
z button.
] icon can be configured by pressing the [ z z
[ ] button.
]
4
Finish the setup process.
z z z z
[ ] button in step 1 is displayed again, showing the option you configured.
• To undo any accidental setting changes, you can restore the camera’s default
).
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
20
Using the Menu Screen
Configure a variety of camera functions through the menu screen as follows.
Menu items are grouped by purpose on tabs, such as shooting [ ], playback
[ ], and so on. Note that available menu items vary depending on the
selected shooting or playback mode ( = 132
–
).
1
Access the menu screen.
z z ] button.
2
Choose a tab.
z z z z buttons to choose a tab initially, you can switch between tabs by pressing the
[ ][ ] buttons.
3
Choose a menu item.
z z z item.
z first press the [ ] or [ ] button to switch screens, and then press the [ ][ ] buttons to select the menu item.
z z the [ ] button.
4
Choose an option.
z z option.
5
Finish the setup process.
z z
[
] button to return to the screen displayed before you pressed the
] button in step 1.
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
• To undo any accidental setting changes, you can restore the camera’s default
).
21
On-Screen Keyboard
Use the on-screen keyboard to enter information for Wi-Fi connections
(
). Note that the length and type of information you can enter varies depending on the function you are using.
Entering Characters
z z a character, and then press the [ ] button to enter it.
Moving the Cursor
z z button.
Deleting Characters
z z
The previous character will be deleted.
Confirming Input and Returning to the Previous Screen
z z ] button.
Indicator Display
The indicator on the back of the camera ( = 3 ) blinks in green at these
times.
- Connected to a computer ( = 110
)
)
- Starting up, recording, or reading
- Communicating with other devices
- Shooting long exposures (
)
- Connecting/transmitting via Wi-Fi
• When the indicator blinks green, do not turn the camera off, or open the memory card/battery cover, or shake or hit the camera.
This may corrupt images or damage the camera or memory card.
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
22
Auto Mode
Convenient mode for easy shots with greater control over shooting
Shooting with Camera-Determined
Settings ............................................................
Shooting (Smart Auto) ...........................................
Scene Icons ..........................................................
Image Stabilization Icons ......................................
On-Screen Frames ................................................
Common, Convenient Features ......................
Zooming In Closer on Subjects (Digital Zoom) .....
Auto Zooming in Response to Subject Movement
(Auto Zoom) ..........................................................
Using the Self-Timer..............................................
Deactivating the Flash ...........................................
Adding a Date Stamp ............................................
Continuous Shooting .............................................
Image Customization Features .......................
Changing the Number of Recording Pixels
(Image Size) ..........................................................
Changing Movie Image Quality .............................
Customizing Camera Operation .....................
Deactivating the Lamp ..........................................
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
23
Shooting with Camera-Determined
Settings
For fully automatic selection of the optimal settings for specific scenes, simply let the camera determine the subject and shooting conditions.
Movies Still Images
Shooting (Smart Auto)
1
Turn the camera on.
z z z z
2
Enter [ ] mode.
z z
[ ] is displayed.
z z camera will make a slight clicking noise as it determines the scene.
z z stabilization mode are displayed in the upper right of the screen (
,
).
z z subjects indicate that they are in focus.
Zoom Bar
3
Compose the shot.
z z the zoom lever toward [ ] (telephoto), and to zoom away from the subject, move it toward [ ] (wide angle). (A zoom bar showing the zoom position is displayed.)
4
Shoot.
Shooting Still Images
Focus.
z z camera beeps twice after focusing, and
AF frames are displayed to indicate image areas in focus.
z z multiple areas are in focus.
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
24
Elapsed Time
Shoot.
z z z down.
z is played, and in low-light conditions, the flash fires automatically.
z z sound ends.
z z revert to the shooting screen.
Recording Movies
Start recording.
z z beeps once as recording begins, and
[ Rec] is displayed with the elapsed time.
z z bottom edges of the screen, and the subject is slightly enlarged. The black bars indicate image areas not recorded.
z z z faces indicate that they are in focus.
z off the movie button.
Resize the subject and recompose the shot as needed.
z z
operations in step 3 ( = 24 ). However,
note that the sound of camera operations will be recorded. Note that movies shot at zoom factors shown in blue will look grainy.
z z focus, brightness, and colors will be automatically adjusted.
Finish recording.
z z recording. The camera beeps twice as recording stops.
z z the memory card becomes full.
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
25
Still Images/Movies
• If the camera makes no operating sounds, it may have been turned on while holding down the [ ] button. To activate sounds, press the
[ ] button, choose [Mute] on the [ ] tab, and then press the
[ ][ ] buttons to choose [Off].
Still Images
• A blinking [ ] icon warns that images are more likely to be blurred by camera shake. In this case, mount the camera on a tripod or take other measures to keep it still.
• If your shots are dark despite the flash firing, move closer to the
subject. For details on the flash range, see “Camera” ( = 135 ).
• The subject may be too close if the camera only beeps once when you press the shutter button halfway. For details on the range of
focus (shooting range), see “Shooting Range” ( = 137 ).
• To reduce red-eye and to assist in focusing, the lamp may be lit when shooting in low-light conditions.
• A blinking [ ] icon displayed when you attempt to shoot indicates that shooting is not possible until the flash has finished recharging.
Shooting can resume as soon as the flash is ready, so either press the shutter button all the way down and wait, or release it and press it again.
• Although you can shoot again before the shooting screen is displayed, your previous shot may determine the focus, brightness, and colors used.
•
You can change how long images are displayed after shots ( = 53
).
Movies
Microphone
• Keep your fingers away from the microphone while recording movies.
Blocking the microphone may prevent audio from being recorded or may cause the recording to sound muffled.
• Avoid touching camera controls other than the movie button when recording movies, because sounds made by the camera will be recorded.
• Once movie recording begins, the image display area changes and subjects are enlarged to allow for correction of significant camera shake. To shoot subjects at the same size shown before shooting,
adjust the image stabilization setting ( = 54 ).
• Audio recording is monaural.
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
26
Still Images Movies
Scene Icons
In [ ] mode, shooting scenes determined by the camera are indicated by the icon displayed, and corresponding settings are automatically selected for optimal focusing, subject brightness, and color.
Subject
People Other Subjects
In
Motion* 1
Shadows on Face* 1
In
Motion* 1
At Close
Range
Icon
Background
Color
Background
Bright
Gray
Backlit –
With Blue Sky
Light Blue
Backlit
Sunsets –
–
– Orange
Spotlights
Dark
Tripod Used * 2 – * 2 –
Dark Blue
*1 Not displayed for movies.
*2 Displayed in dark scenes when the camera is held still, as when mounted on a tripod.
• Try shooting in [ ] mode (
) if the scene icon does not match actual shooting conditions, or if it is not possible to shoot with your expected effect, color, or brightness.
Still Images Movies
Image Stabilization Icons
[
Optimal image stabilization for the shooting conditions is automatically applied (Intelligent IS). Additionally, the following icons are displayed in
] mode.
Image stabilization for still images
(Normal)
Image stabilization for still images when panning* (Panning)
Image stabilization for angular camera shake and shift-shake in macro shots (Hybrid IS).
For movies, [
[ applied.
] is displayed and
] image stabilization is also
Image stabilization for movies, reducing strong camera shake, as when recording while walking
(Dynamic)
Image stabilization for slow camera shake, such as when recording movies at telephoto
(Powered)
No image stabilization, because the camera is mounted on a tripod or held still by other means.
However, during movie recording,
[ ] is displayed, and image stabilization to counteract wind or other sources of vibration is used
(Tripod IS).
* Displayed when you pan, following moving subjects with the camera. When you follow subjects moving horizontally, image stabilization only counteracts vertical camera shake, and horizontal stabilization stops. Similarly, when you follow subjects moving vertically, image stabilization only counteracts horizontal camera shake.
•
To cancel image stabilization, set [IS Mode] to [Off] ( = 54
). In this case, an
IS icon is not displayed.
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
27
Still Images Movies
On-Screen Frames
A variety of frames are displayed once the camera detects subjects you are aiming the camera at.
• A white frame is displayed around the subject (or person’s face) determined by the camera to be the main subject, and gray frames are displayed around other detected faces. Frames follow moving subjects within a certain range to keep them in focus.
However, if the camera detects subject movement, only the white frame will remain on the screen.
• When you are pressing the shutter button halfway and the camera detects subject movement, a blue frame is displayed, and the focus and image brightness are constantly adjusted (Servo AF).
• Try shooting in [ ] mode (
) if no frames are displayed, if frames are not displayed around desired subjects, or if frames are displayed on the background or similar areas.
Common, Convenient Features
Still Images Movies
Zooming In Closer on Subjects (Digital Zoom)
When distant subjects are too far away to enlarge using optical zoom, use digital zoom for up to about 40x enlargement.
Zoom Factor
1
Move the zoom lever toward
[ ].
z z z z before the image becomes noticeably grainy, which is then indicated on the screen.
2
Move the zoom lever toward
[ ] again.
z z subject.
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
28
• Moving the zoom lever will display the zoom bar (which indicates the zoom position). The zoom bar is color-coded to indicate the zoom range.
- White range: optical zoom range where the image will not appear grainy.
- Yellow range: digital zoom range where the image is not noticeably grainy (ZoomPlus).
- Blue range: digital zoom range where the image will appear grainy.
Because the blue range will not be available at some recording pixel settings (
), the maximum zoom factor can be achieved by following step 1.
• Zoomed images may look grainy under some recording pixel settings (
) and zoom factors. In this case, the zoom factor is shown in blue.
Auto Zooming in Response to Subject
Movement (Auto Zoom)
Still Images
The camera automatically zooms in and out to keep a detected face
(
= 24 ) at a constant size. If the person moves closer, the camera
automatically zooms out, and vice versa.
1
Enter Auto Zoom mode.
z z z z ] is displayed.
z z detected face, and the camera zooms in and out to keep the subject on the screen.
z z white frame is displayed around the main subject’s face and up to two gray frames around other faces, as the camera zooms to keep these subjects on the screen.
2
Shoot.
z z shoot, and the frames are still displayed.
z z button again. [ ] is displayed.
• Faces may not be detected at some zoom factors, or if the subject’s head is tilted or facing the camera indirectly.
• Auto zooming is deactivated in the following situations.
- When you change the shooting mode
- When you press the [
- When you press the [ ] button
] button, movie button, or [ ] button
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
29
• When a detected subject moves toward the edge of the screen, the camera zooms out to keep the subject on the screen.
• The zoom factor cannot be changed after you press the shutter button all the way down in self-timer mode (
).
• The camera prioritizes zooming to keep subjects on the screen. For this reason, it may not be possible to maintain a constant face display size, depending on subject movement and shooting conditions.
• When no face is detected, the camera zooms to a certain level and stops zooming until a face is detected.
Still Images Movies
Using the Self-Timer
With the self-timer, you can include yourself in group photos or other timed shots. The camera will shoot about 10 seconds after you press the shutter button.
1
Configure the setting.
z z z
menu, and then choose [ ] ( = 20
).
z displayed.
2
Shoot.
z z halfway to focus on the subject, and then press it all the way down.
z z
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
30
z z will blink and the camera will play a self-timer sound.
z z and sound will speed up. (The lamp will remain lit in case the flash fires.) z z
[ triggered the self-timer, press the
] button.
z z in step 1.
Still Images Movies
Using the Self-Timer to Avoid Camera Shake
This option delays shutter release until about two seconds after you have pressed the shutter button. If the camera is unsteady while you are pressing the shutter button, it will not affect your shot.
z z
(
) and choose [ ].
z z displayed.
z z
(
) to shoot.
Still Images Movies
Customizing the Self-Timer
You can specify the delay (0 – 30 seconds) and number of shots (1 – 10).
1
Choose [ ].
z z
[
( = 30 ), choose [ ] and press the
] button.
2
Configure the setting.
z z
[Delay] or [Shots].
z z value, and then press the [ ] button.
z z displayed.
z z
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
• For movies shot using the self-timer, [Delay] represents the delay before recording begins, but the [Shots] setting has no effect.
• When you specify multiple shots, image brightness and white balance are determined by the first shot. More time is required between shots when the flash fires or when you have specified to take many shots. Shooting will stop automatically when the memory card becomes full.
• When a delay longer than two seconds is specified, two seconds before the shot, the lamp blinking and self-timer sound will speed up. (The lamp will remain lit in case the flash fires.)
31
Deactivating the Flash
Prepare the camera for shooting without the flash as follows.
Still Images z z
[ ] is displayed.
z z z z again. ([ ] is displayed.) The flash will automatically fire in low-light conditions.
• If a blinking [ ] icon is displayed when you press the shutter button halfway in camera-shake inducing, low-light conditions, mount the camera on a tripod or take other measures to keep it still.
Still Images
Adding a Date Stamp
The camera can add the shooting date to images, in the lower-right corner.
However, note that date stamps cannot be edited or removed, so confirm beforehand that the date and time are correct (
).
1
Configure the setting.
z z ] button, choose [Date
Stamp ] on the [ ] tab, and then choose the desired option (
z z displayed.
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
2
Shoot.
z z shooting date or time to the lower-right corner of images.
z z
[Off] in step 1.
• Date stamps cannot be edited or removed.
32
• Shots taken without adding a date stamp can be printed with one as follows.
However, adding a date stamp this way to images that already have one may cause it to be printed twice.
- Print using printer functions (
)
- Use camera DPOF print settings (
) to print
-
Use the software downloaded from the Canon website ( = 109 ) to print
Still Images
Continuous Shooting
Hold the shutter button all the way down to shoot continuously.
For details on the continuous shooting speed, see “Camera” ( = 135 ).
1
Configure the setting.
z z menu, and then choose [ ] (
).
z z displayed.
2
Shoot.
z z to shoot continuously.
•
Cannot be used with the self-timer ( = 30 ).
• Shooting may stop momentarily or continuous shooting may slow down depending on shooting conditions, camera settings, and the zoom position.
• As more shots are taken, shooting may slow down.
• Shooting may slow down if the flash fires.
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
33
Image Customization Features
Still Images
Changing the Number of Recording Pixels
(Image Size)
Choose the image’s number of recording pixels from 5 levels, as follows.
For guidelines on how many shots at each recording pixel setting can fit on
a memory card, see “Number of Shots per Memory Card” ( = 137 ).
z z menu, and choose the desired option
(
).
z z z displayed.
z process but choose [ ].
Guidelines for Choosing Recording Pixel Setting Based on Paper Size
A2 (16.5 x 23.4 in.) z z
A3 – A5 (11.7 x
16.5 – 5.8 x 8.3 in.)
5 x 7 in.
Postcard
3.5 x 5 in.
z z
HDTVs or similar display devices, on a
16:9 screen.
Movies
Changing Movie Image Quality
Two image quality settings are available. For guidelines on the total recording time for movies at each level of image quality that will fit on a
memory card, see “Recording Time per Memory Card” ( = 137 ).
z z menu, and choose the desired option
z z displayed.
z z process but choose [ ].
Image
Quality
Number of
Recording Pixels
1280 x 720
640 x 480
Frame Rate
25 fps
30 fps
Details
For shooting in HD.
For shooting in standard definition.
• In [ ] mode, black bars displayed on the top and bottom edges of the screen indicate image areas not recorded.
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
34
Customizing Camera Operation
Customize shooting functions on the [ ] tab of the menu screen as follows.
For instructions on menu functions, see “Using the Menu Screen” ( = 21 ).
Still Images
Deactivating the Lamp
You can deactivate the lamp that normally lights up to help you focus in low-light conditions when you press the shutter button halfway, or that lights up to reduce red-eye when you shoot in low-light conditions with the flash.
z z
[Off] (
).
] button, choose [Lamp
Setting] on the [ ] tab, and then choose z z process but choose [On].
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
35
Other Shooting Modes
Shoot more effectively in various scenes, and take shots enhanced with unique image effects or captured using special functions
Specific Scenes ................................................
Applying Special Effects .................................
Shooting with a Fish-Eye Lens Effect
(Fish-Eye Effect) ...................................................
Shots Resembling Miniature Models
(Miniature Effect) ...................................................
Shooting with a Toy Camera Effect
(Toy Camera Effect) ..............................................
Shooting in Monochrome ......................................
Special Modes for Other Purposes ................
Auto Shooting after Detecting New Person
(Face Self-Timer) ..................................................
Shooting Long Exposures (Long Shutter) .............
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
36
Specific Scenes
Choose a mode matching the shooting scene, and the camera will automatically configure the settings for optimal shots.
1
Choose a shooting mode.
z z z
[ ] is displayed.
z menu, and choose the desired option
(
).
2
Shoot.
Still Images Movies
Shooting Portraits (Portrait)
z z effect.
Still Images
Shooting under Low Light
(Low Light)
z z shake even in low-light conditions.
Still Images Movies
Shooting Fireworks (Fireworks)
z z
• In [ ] mode, mount the camera on a tripod or take other measures to keep it still and prevent camera shake.
• Set [IS Mode] to [Off] when using a tripod or other means to secure the camera (
).
• [ ] mode recording pixel setting is [ ] (2560 x 1920) and cannot be changed.
• In [ ] mode, although no frames are displayed when you press the shutter button halfway, optimal focus is still determined.
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
37
Applying Special Effects
Add a variety of effects to images when shooting.
1
Choose a shooting mode.
z z
(
) to choose a shooting mode.
2
Shoot.
Still Images Movies
Shooting in Vivid Colors
(Super Vivid)
z z
Still Images Movies
Posterized Shots (Poster Effect)
z z illustration.
Shooting with a Fish-Eye Lens Effect
(Fish-Eye Effect)
Shoot with the distorting effect of a fish-eye lens.
Still Images
1
Choose [ ].
z z
2
Choose an effect level.
z z buttons to choose an effect level, and then press the [ ] button.
z z look with the effect applied.
3
Shoot.
• Try taking some test shots first, to make sure you obtain the desired results.
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
• In [ ] and [ ] modes, try taking some test shots first, to make sure you obtain the desired results.
38
Still Images
Shots Resembling Miniature Models
(Miniature Effect)
Movies
Creates the effect of a miniature model, by blurring image areas above and below your selected area.
You can also make movies that look like scenes in miniature models by choosing the playback speed before the movie is recorded. People and objects in the scene will move quickly during playback. Note that sound is not recorded.
1
Choose [ ].
z z
(
) and choose [ ].
z z image area that will not be blurred.
2
Choose the area to keep in focus.
z z z z and press the [ ][ ] buttons to move it.
3
For movies, choose the movie playback speed.
z z ] button, and then press the [ ][ ] buttons to choose the speed.
4
Return to the shooting screen and shoot.
z z ] button to return to the shooting screen, and then shoot.
Playback Speed and Estimated Playback Time
(for One-Minute Clips)
Speed Playback Time
Approx. 12 sec.
Approx. 6 sec.
Approx. 3 sec.
• The zoom is not available when shooting movies. Be sure to set the zoom before shooting.
• Try taking some test shots first, to make sure you obtain the desired results.
• To switch the orientation of the frame to vertical, press the [ ][ ] buttons in step 2. To return the frame to horizontal orientation, press the [ ][ ] buttons.
• To move the frame when it is in horizontal orientation, press the [ ][ ] buttons, and to move the frame when it is in vertical orientation, press the
[ ][ ] buttons.
• Holding the camera vertically will change the orientation of the frame.
• Movie image quality is [ ] when a still image recording pixel setting of [ ] is selected and [ ] when a still image recording pixel setting of [ ] is selected
(
= 34 ). These quality settings cannot be changed.
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
39
Still Images
Shooting with a Toy Camera Effect
(Toy Camera Effect)
This effect makes images resemble shots from a toy camera by vignetting
(darker, blurred image corners) and changing the overall color.
1
Choose [ ].
z z
(
) and choose [ ].
2
Choose a color tone.
z z buttons to choose a color tone, and then press the [ ] button.
z z look with the effect applied.
3
Shoot.
Standard Shots resemble toy camera images.
Warm Images have a warmer tone than with [Standard].
Cool Images have a cooler tone than with [Standard].
• Try taking some test shots first, to make sure you obtain the desired results.
Still Images
Shooting in Monochrome
Shoot images in black and white, sepia, or blue and white.
B/W
Sepia
Blue
Movies
Black and white shots.
Sepia tone shots.
Blue and white shots.
1
Choose [ ].
z z
2
Choose a color tone.
z z buttons to choose a color tone, and then press the [ ] button.
z z look with the effect applied.
3
Shoot.
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
40
Special Modes for Other Purposes
Still Images
Auto Shooting after Detecting New Person
(Face Self-Timer)
The camera will shoot about two seconds after detecting that the face of another person (such as the photographer) has entered the shooting area
(
). This is useful when including yourself in group photos or similar shots.
1
Choose [ ].
z z
(
) and choose [ ].
2
Compose the shot and press the shutter button halfway.
z z around the face you focus on and white frames around other faces.
3
Press the shutter button all the way down.
z z mode, and [Look straight at camera to start count down] is displayed.
z z is played.
4
Join the subjects in the shooting area and look at the camera.
z z lamp blinking and self-timer sound will speed up. (When the flash fires, the lamp will remain lit.) About two seconds later, the camera will shoot.
z z
[ triggered the self-timer, press the
] button.
• Even if your face is not detected after you join the others in the shooting area, the camera will shoot about 15 seconds later.
• To change the number of shots, press the [ ] button, press the [ ][ ] buttons to choose the number of shots, and then press the [ ] button.
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
41
Still Images
Shooting Long Exposures (Long Shutter)
Specify a shutter speed of 1 – 15 seconds to shoot long exposures. In this case, mount the camera on a tripod or take other measures to prevent camera shake.
1
Choose [ ].
z z
(
) and choose [ ].
2
Choose the shutter speed.
z z menu, and choose the desired shutter
3
Check the exposure.
z z the exposure for your selected shutter speed.
4
Shoot.
• On-screen image brightness in step 3, when you pressed the shutter button halfway, may not match the brightness of your shots.
• With shutter speeds of 1.3 seconds or slower, there will be a delay before you can shoot again, as the camera processes images to reduce noise.
• Set [IS Mode] to [Off] when using a tripod or other means to secure
• If the flash fires, your shot may be overexposed. In this case, set the flash to
).
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
42
P Mode
More discerning shots, in your preferred shooting style
• Instructions in this chapter apply to the camera when set to [ ] mode.
• [ ]: Program AE; AE: Auto Exposure
•
).
Shooting in Program AE ([P] Mode) ...............
Image Brightness (Exposure) .........................
(Exposure Compensation) ....................................
Changing the Metering Method .............................
Changing the ISO Speed ......................................
Correcting Image Brightness (i-Contrast) ..............
Adjusting White Balance .................................
Shooting Range and Focusing .......................
Shooting Close-Ups (Macro) .................................
Shooting Distant Subjects (Infinity) .......................
Changing the AF Frame Mode ..............................
Magnifying the Area in Focus ................................
Changing the Focus Setting ..................................
Flash ..................................................................
Changing the Flash Mode .....................................
Other Settings ..................................................
Displaying Grid Lines ............................................
Deactivating the Digital Zoom ...............................
Changing the Image Display Style after Shots ......
Changing the IS Mode Settings ............................
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
43
Still Images Movies
Shooting in Program AE ([P] Mode)
You can customize many function settings to suit your preferred shooting style.
1
Enter [ ] mode.
z z
(
) and choose [ ].
2
Customize the settings as
desired (
–
), and then shoot.
• If the optimum exposure cannot be obtained when you press the shutter button halfway, the shutter speed and aperture value are displayed in orange. In this case, try adjusting the ISO speed (
= 45 ) or activating the flash (if subjects
), which may enable optimum exposure.
• Movies can be recorded in [ ] mode as well, by pressing the movie button.
However, some FUNC. (
) settings may be automatically adjusted for movie recording.
•
For details on the shooting range in [ ] mode, see “Shooting Range”
Image Brightness (Exposure)
Still Images
Adjusting Image Brightness
(Exposure Compensation)
Movies
The standard exposure set by the camera can be adjusted in 1/3-stop increments, in a range of –2 to +2.
z z in the menu. As you watch the screen, press the [ ][ ] buttons to adjust
z z exposure compensation bar displayed.
z z
[ ] button to display the set exposure compensation amount, and then shoot.
• You can also shoot still images with exposure compensation bar displayed.
• While recording a movie, [ ] is displayed, and the exposure is locked.
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
44
Still Images
Changing the Metering Method
Adjust the metering method (how brightness is measured) to suit shooting conditions as follows.
z z menu, and choose the desired option
(
z z displayed.
Evaluative
Center
Weighted Avg.
For typical shooting conditions, including backlit shots.
Automatically adjusts exposure to match the shooting conditions.
Determines the average brightness of light across the entire image area, calculated by treating brightness in the central area as more important.
Spot
Metering restricted to within the [ displayed in the center of the screen.
] (Spot AE Point frame),
Still Images
Changing the ISO Speed
Set the ISO speed to [AUTO] for automatic adjustment to suit the shooting mode and conditions. Otherwise, set a higher ISO speed for higher sensitivity, or a lower value for lower sensitivity.
z z menu, and choose the desired option
z z displayed.
• To view the automatically determined ISO speed when you have set the ISO speed to [AUTO], press the shutter button halfway.
• Although choosing a lower ISO speed may reduce image graininess, there may be a greater risk of subject and camera shake in some shooting conditions.
• Choosing a higher ISO speed will increase shutter speed, which may reduce subject and camera shake and increase the flash range. However, shots may look grainy.
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
45
Still Images
Correcting Image Brightness (i-Contrast)
Before shooting, excessively bright or dark image areas (such as faces or backgrounds) can be detected and automatically adjusted to the optimal brightness. Insufficient overall image contrast can also be automatically corrected before shooting to make subjects stand out better.
z z ] button, choose
[i-Contrast] on the [ ] tab, and then choose [Auto] (
).
z z displayed.
• Under some shooting conditions, correction may be inaccurate or may cause images to appear grainy.
• You can also correct existing images (
Movies
By adjusting white balance (WB), you can make image colors look more natural for the scene you are shooting.
z z menu, and choose the desired option
z z displayed.
Still Images
Adjusting White Balance
Auto
Day Light
Cloudy
Tungsten
Fluorescent
Automatically sets the optimal white balance for the shooting conditions.
For shooting outdoors in fair weather.
For shooting in cloudy conditions, in the shade, or at twilight.
For shooting under ordinary incandescent (tungsten) lighting and similarly colored fluorescent lighting.
For shooting under warm-white (or similarly colored) or cool-white fluorescent lighting.
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
Custom
For manually setting a custom white balance ( = 47
).
46
Still Images Movies
Custom White Balance
For image colors that look natural under the light in your shot, adjust white balance to suit the light source where you are shooting. Set the white balance under the same light source that will illuminate your shot.
z z z
].
z so that the entire screen is white. Press the [ ] button.
z z white balance data has been recorded.
• Colors may look unnatural if you change camera settings after recording white balance data.
Shooting Range and Focusing
z z z menu, and then choose [ ] (
).
Once the setting is complete, [ ] is displayed.
Still Images
Shooting Close-Ups (Macro)
To restrict the focus to subjects at close range, set the camera to [ ]. For
details on the range of focus, see “Shooting Range” ( = 137 ).
• If the flash fires, vignetting may occur.
• In the yellow bar display area below the zoom bar, [ ] will turn gray and the camera will not focus.
• To prevent camera shake, try mounting the camera on a tripod and shooting
with the camera set to [ ] ( = 31 ).
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
47
Still Images
Shooting Distant Subjects (Infinity)
To restrict the focus to distant subjects, set the camera to [ ]. For details
on the range of focus, see “Shooting Range” ( = 137 ).
z z z menu, and then choose [ ] (
Once the setting is complete, [ ] is displayed.
Still Images
Changing the AF Frame Mode
Movies
Change the AF (auto focus) frame mode to suit the shooting conditions as follows.
z z ] button, choose [AF
Frame] on the [ ] tab, and then choose
Still Images Movies
Face AiAF
• Detects people’s faces, and then sets the focus, exposure (evaluative metering only), and white balance ([ ] only).
• After you aim the camera at the subject, a white frame is displayed around the person’s face determined by the camera to be the main subject, and up to two gray frames are displayed around other detected faces.
• When the camera detects movement, frames will follow moving subjects, within a certain range.
• After you press the shutter button halfway, up to nine green frames are displayed around faces in focus.
• If faces are not detected, or when only gray frames are displayed
(without a white frame), up to nine green frames are displayed in the areas in focus when you press the shutter button halfway.
•
If faces are not detected when Servo AF ( = 49
) is set to [On], the
AF frame is displayed in the center of the screen when you press the shutter button halfway.
• Examples of faces that cannot be detected:
- Subjects that are distant or extremely close
- Subjects that are dark or light
- Faces in profile, at an angle, or partly hidden
• The camera may misinterpret non-human subjects as faces.
• No AF frames are displayed if the camera cannot focus when you press the shutter button halfway.
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
48
Still Images
Choosing Subjects to Focus On (Tracking AF)
Shoot after choosing a subject to focus on as follows.
1
Choose [Tracking AF].
z z
Frame Mode” ( = 48 ) to choose
[Tracking AF].
z z screen.
2
Choose a subject to focus on.
z z z desired subject.
z changes to a blue [ ], which follows the subject as the camera continues to adjust the focus and exposure (Servo AF)
(
).
3
Shoot.
z z to shoot.
•
) is set to [On] and cannot be changed.
• Tracking may not be possible when subjects are too small or move too rapidly, or when subject color or brightness matches that of the background too closely.
• [AF-Point Zoom] on the [ ] tab is not available.
• [ ] and [ ] are not available.
Still Images Movies
Center
One AF frame is displayed in the center. Effective for reliable focusing.
• A yellow AF frame is displayed with [ ] if the camera cannot focus when you press the shutter button halfway.
• To compose shots so that subjects are positioned at the edge or in a corner, first aim the camera to capture the subject in an AF frame, and then hold the shutter button halfway down. As you continue to hold the shutter button halfway, recompose the shot as desired, and then press the shutter button all the way down (Focus Lock).
Still Images
Shooting with Servo AF
This mode helps avoid missing shots of subjects in motion, because the camera continues to focus on the subject and adjust the exposure as long as you press the shutter button halfway.
1
Configure the setting.
z z
] button, choose [Servo
AF] on the [ ] tab, and then choose [On]
2
Focus.
z z where the blue AF frame is displayed while you are pressing the shutter button halfway.
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
49
• Focusing may not be possible in some shooting conditions.
• In low-light conditions, Servo AF may not be activated (AF frames may not turn blue) when you press the shutter button halfway. In this case, the focus and exposure are set according to the specified AF frame mode.
• If optimum exposure cannot be obtained, the shutter speed and aperture value are displayed in orange. Release the shutter button, and then press it halfway again.
• [AF-Point Zoom] on the [ ] tab (
) is not available.
•
Not available when using the self-timer ( = 30 ).
Still Images
Magnifying the Area in Focus
You can check the focus by pressing the shutter button halfway, which will enlarge the portion of the image in focus in the AF frame.
1
Configure the setting.
z z ] button, choose [AF-
Point Zoom] on the [ ] tab, and then choose [On] (
).
2
Check the focus.
z z detected as the main subject is magnified when the shutter button is pressed halfway. In [Center] AF mode, the AF frame in the center is magnified.
• The area in focus is not magnified in the following cases when the shutter button is pressed halfway.
- [Face AiAF]: When a face was not detected, or when the person is too close to the camera and their face is too large for the screen
- [Center]: When the camera cannot focus on the subject
- [Tracking AF]: Not magnified in this mode
- When digital zoom is used (
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
50
Still Images
Changing the Focus Setting
You can change default camera operation of constantly focusing on subjects it is aimed at, even when the shutter button is not pressed. Instead, you can limit camera focusing to the moment you press the shutter button halfway.
z z ] button, choose
[Continuous AF] on the [ ] tab, and then
On
Off
Helps avoid missing sudden photo opportunities, because the camera constantly focuses on subjects until you press the shutter button halfway.
Conserves battery power, because the camera does not focus constantly.
Flash
Still Images
Changing the Flash Mode
You can change the flash mode to match the shooting scene. For details on
the flash range, see “Camera” ( = 135 ).
[ ] Auto
Fires automatically in low-light conditions.
[ ] On
Fires for each shot.
z z buttons to choose a flash mode, and then press the [ ] button.
z z displayed.
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
[ ] Slow Synchro
Fires to illuminate the main subject (such as people) while shooting at a slower shutter speed to illuminate backgrounds out of flash range.
• In [ ] mode, mount the camera on a tripod or take other measures to keep it still and prevent camera shake.
• In [ ] mode, even after the flash fires, ensure that the main subject does not move until the shutter sound is finished playing.
• Set [IS Mode] to [Off] when using a tripod or other means to secure the camera (
).
51
[ ] Off
For shooting without the flash.
• If a blinking [ ] icon is displayed when you press the shutter button halfway in camera-shake inducing, low-light conditions, mount the camera on a tripod or take other measures to keep it still.
Other Settings
Still Images Movies
Displaying Grid Lines
Grid lines can be displayed on the screen for vertical and horizontal reference while shooting.
z z
).
] button, choose [Grid
Lines] on the [ ] tab, and then choose z z are displayed on the screen.
• Grid lines are not recorded in your shots.
Still Images
Deactivating the Digital Zoom
Movies
If you prefer not to use the digital zoom (
), you can deactivate it as follows.
z z ] button, choose
[Digital Zoom] on the [ ] tab, and then choose [Off] (
).
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
52
Still Images
Changing the Image Display Style after Shots
You can change how long images are displayed and what information is displayed immediately after shooting.
Changing the Image Display Period after Shots
1
Access the [Review image after shooting] screen.
z z ] button, choose
[Review image after shooting] on the
[ ] tab, and then press the [ ] button
(
).
2
Configure the setting.
z z
Quick Displays images only until you can shoot again.
2 sec., 4 sec.,
8 sec.
Displays images for the specified time. Even while the shot is displayed, you can take another shot by pressing the shutter button halfway again.
Hold
Off
Displays images until you press the shutter button halfway.
No image display after shots.
Changing the Screen Displayed after Shots
Change the way images are displayed after shots as follows.
Off
Detailed
1
Set [Display Time] to [2 sec.],
[4 sec.], [8 sec.], or [Hold]
(
).
2
Configure the setting.
z z the desired option (
).
Displays only the image.
Displays shooting details ( = 128 ).
• When [Display Time] (
= 53 ) is set to [Off] or [Quick], [Display Info] is set to
[Off] and cannot be changed.
• By pressing the [ ] button while an image is displayed after shooting, you can switch the display information. Note that the settings of [Display Info] are not changed. You can also erase images by pressing the [ ] button, or protect images (
= 60 ) by pressing the [ ] button.
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
53
Still Images
Changing the IS Mode Settings
Movies
1
Access the setting screen.
z z ] button, choose [IS
Settings] on the [ ] tab, and then press the [ ] button (
).
2
Configure the setting.
z z
Continuous
Optimal image stabilization for the shooting conditions is automatically
applied (Intelligent IS) ( = 27
).
Shoot Only* Image stabilization is active only at the moment of shooting.
Off Deactivates image stabilization.
* The setting is changed to [Continuous] for movie recording.
• If image stabilization cannot prevent camera shake, mount the camera on a tripod or take other measures to hold it still. In this case, set [IS Mode] to [Off].
Movies
Recording Movies with Subjects at the Same Size Shown before Shooting
Normally, once movie recording begins, the image display area changes and subjects are enlarged to allow for correction of significant camera shake. To shoot subjects at the same size shown before shooting, you can choose not to reduce significant camera shake.
z z
Mode Settings” ( = 54 ) to access the
[IS Settings] screen.
z z
[2] (
).
• When the movie quality is [ ] (
), Dynamic IS is [1] and cannot be changed.
• You can also set [IS Mode] to [Off], so that subjects are recorded at the same size shown before shooting.
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
54
Playback Mode
Have fun reviewing your shots, and browse or edit them in many ways
• To prepare the camera for these operations, press the [ ] button to enter Playback mode.
• It may not be possible to play back or edit images that were renamed or already edited on a computer, or images from other cameras.
Viewing ..............................................................
Switching Display Modes ......................................
Browsing and Filtering Images .......................
Navigating through Images in an Index.................
Finding Images Matching Specified Conditions ....
Image Viewing Options ....................................
Magnifying Images ................................................
Viewing Slideshows ..............................................
Protecting Images ............................................
Using the Menu .....................................................
Choosing Images Individually ...............................
Selecting a Range .................................................
Protecting All Images at Once ...............................
Erasing Images .................................................
Erasing Multiple Images at Once ..........................
Rotating Images ...............................................
Using the Menu .....................................................
Deactivating Auto Rotation ....................................
Tagging Images as Favorites ..........................
Using the Menu .....................................................
Editing Still Images ..........................................
Resizing Images ....................................................
Correcting Image Brightness (i-Contrast) ..............
Correcting Red-Eye ...............................................
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
55
Still Images Movies
Viewing
After shooting images or movies, you can view them on the screen as follows.
1
Enter Playback mode.
z z z z
2
Browse through your images.
z z button. To view the next image, press the
[ ] button.
z z browse through images quickly.
z z
To play movies, go to step 3.
] icon.
3
Play movies.
z z press the [ ][ ] buttons to choose [ ], and then press the [ ] button again.
Volume Indicator
4
Adjust the volume.
z z volume.
z z indicator is no longer displayed, press the
[ ][ ] buttons.
5
Pause playback.
z z
[ ] button.
z z displayed.
] is
• To switch to Shooting mode from Playback mode, press the shutter button halfway.
• To have the most recent shot displayed when you enter Playback mode,
) ► [ ] tab ► [Resume] ► [Last shot].
• To change the transition shown between images, access MENU (
choose your desired effect on the [ ] tab ► [Transition].
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
56
Still Images Movies
Switching Display Modes
Press the [ ] button to view other information on the screen, or to hide
the information. For details on the information displayed, see “Playback
(Detailed Information Display)” ( = 128 ).
No Information
Display
Simple
Information
Display
Detailed
Information
Display
Still Images Movies
Overexposure Warning (for Image Highlights)
Washed-out highlights in the image flash on the screen in detailed
).
Still Images Movies
Histogram
z z
(
) is a histogram showing the distribution of brightness in the image.
The horizontal axis represents the degree of brightness, and the vertical axis, how much of the image is at each level of brightness. Viewing the histogram is a way to check exposure.
Browsing and Filtering Images
Still Images
Navigating through Images in an Index
Movies
By displaying multiple images in an index, you can quickly find the images you are looking for.
1
Display images in an index.
z z ] to display images in an index. Moving the lever again will increase the number of images shown.
z z lever toward [ ]. Fewer images are shown each time you move the lever.
2
Choose an image.
z z an image.
z z selected image.
z z image in single-image display.
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
57
Still Images
Finding Images Matching Specified
Conditions
Movies
Find desired images quickly on a memory card full of images by filtering image display according to your specified conditions. You can also protect
(
) or delete (
) these images all at once.
Shot Date
Favorites
Displays the images shot on a specific date.
Displays images tagged as favorites ( = 66
).
Still image/Movie Displays only still images or movies.
1
Choose the first condition for image display or navigation.
z z ] in the menu, and choose a condition (
).
2
Choose the second condition for image display or navigation.
z z a condition, and then press the [ ] button.
3
View the filtered images.
z z displayed in yellow frames. To view only these images, press the [ ][ ] buttons.
z z step 1.
• When the camera has found no corresponding images for some conditions, those conditions will not be available.
• To show or hide information, press the [ ] button in step 3.
•
Options for viewing the images found (in step 3) include “Navigating through
Images in an Index” ( = 57 ), “Magnifying Images” (
Slideshows” ( = 59 ). You can protect, erase, or print all images found or add
them to a photobook by choosing [Select All Images in Search] in “Protecting
Images” ( = 60 ), “Erasing Multiple Images at Once” (
Images to the Print List (DPOF)” ( = 116 ), or “Adding Images to a Photobook”
•
If you edit images and save them as new images ( = 67
is displayed, and the images that were found are no longer shown.
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
58
Image Viewing Options
Still Images
Magnifying Images
Approximate Position of
Displayed Area
1
Magnify an image.
z z zoom in and magnify the image. You can magnify images up to about 10x by continuing to hold the zoom lever.
z z toward [ ]. You can return to singleimage display by continuing to hold it.
2
Move the display position and switch images as needed.
z z z
[ ][ ][ ][ ] buttons.
z ] is displayed, you can switch to [ ] by pressing the [ ] button. To switch to other images while zoomed, press the [ ][ ] buttons. Press the [ ] button again to restore the original setting.
• You can return to single-image display from magnified display by pressing the
[ ] button.
Still Images Movies
Viewing Slideshows
Automatically play back images from a memory card as follows. Each image is displayed for about three seconds.
z z menu, and choose the desired option
z z image] is displayed for a few seconds.
z z slideshow.
] button to stop the
•
The camera’s power-saving functions ( = 18
) are deactivated during slideshows.
• To pause or resume slideshows, press the [ ] button.
• You can switch to other images during playback by pressing the [ ][ ] buttons. For fast-forward or fast-rewind, hold the [ ][ ] buttons down.
• In filtered display (
= 58 ), only images matching search conditions are
played.
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
59
Changing Slideshow Settings
You can set up slideshows to repeat, and you can change the transitions between images and the display duration of each image.
1
Access the setting screen.
z z
(
).
] button, and then choose [Slideshow] on the [ ] tab
2
Configure the settings.
z z then choose the desired option (
).
z z choose [Start] and press the [ ] button.
z z
[ ] button.
Still Images
Protecting Images
Protect important images to prevent accidental erasure ( = 63 ).
Movies z z
[
] in the menu ( = 20 ). [Protected]
is displayed.
z z and choose [ the [ ] button.
] again, and then press
• Protected images on a memory card will be erased if you format the
).
• Protected images cannot be erased using the camera’s erasure function. To erase them this way, first cancel protection.
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
60
Using the Menu
1
Access the setting screen.
z z ] button and choose
[Protect] on the [ ] tab (
).
2
Choose a selection method.
z z z desired (
).
z
[ ] button.
Choosing Images Individually
1
Choose [Select].
z z
(
), choose [Select] and press the
[ ] button.
2
Choose an image.
z z image, and then press the [ ] button.
[ ] is displayed.
z z again. [ ] is no longer displayed.
z z images.
3
Protect the image.
z z ] button. A confirmation message is displayed.
z z and then press the [ ] button.
• Images will not be protected if you switch to Shooting mode or turn the camera off before finishing the setup process in step 3.
Selecting a Range
1
Choose [Select Range].
z z
( = 61 ), choose [Select Range] and
press the [ ] button.
2
Choose a starting image.
z z
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index z z image, and then press the [ ] button.
61
3
Choose an ending image.
z z image], and then press the [ ] button.
z z image, and then press the [ ] button.
z z selected as the last image.
4
Protect the images.
z z and then press the [ ] button.
• To cancel protection for groups of images, choose [Unlock] in step 4.
Protecting All Images at Once
1
Choose [Protect All Images].
z z
( = 61 ), choose [Protect All Images]
and press the [ ] button.
2
Protect the images.
z z and then press the [ ] button.
• To cancel protection for groups of images, choose [Unprotect All Images] in step 1.
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
62
Still Images Movies
Erasing Images
You can choose and erase unneeded images one by one. Be careful when erasing images, because they cannot be recovered. However, protected images (
) cannot be erased.
1
Choose an image to erase.
z z image.
2
Erase the image.
z z z z
[ ][ ] buttons to choose [Erase], and then press the [ ] button.
z z z z buttons to choose [Cancel], and then press the [ ] button.
Erasing Multiple Images at Once
You can choose multiple images to erase at once. Be careful when erasing images, because they cannot be recovered. However, protected images
(
Choosing a Selection Method
1
Access the setting screen.
z z ] button, and then
choose [Erase] on the [ ] tab ( = 21
).
2
Choose a selection method.
z z selection method, and then press the [ ] button.
z z
[ ] button.
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
63
1
Choose [Select].
z z
Method” (
press the [ ] button.
2
Choose an image.
z z step 2 in “Choosing Images Individually”
(
), [ ] is displayed.
z z z again. [ ] is no longer displayed.
z images.
3
Erase the images.
z z ] button. A confirmation message is displayed.
z z and then press the [ ] button.
Selecting a Range
1
Choose [Select Range].
z z
), choose [Select
Range] and press the [ ] button.
2
Choose images.
z z
3
Erase the images.
z z and then press the [ ] button.
1
Choose [Select All Images].
z z
), choose [Select All
Images] and press the [ ] button.
2
Erase the images.
z z and then press the [ ] button.
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
64
Rotating Images
Change the orientation of images and save them as follows.
1
Choose [ ].
z z
[ ] in the menu (
).
Still Images
2
Rotate the image.
z z on the desired direction. Each time you press the button, the image is rotated
90°. Press the [ ] button to complete the setting.
Using the Menu
1
Choose [Rotate].
z z ] button and choose
[Rotate] on the [ ] tab ( = 21 ).
2
Rotate the image.
z z image.
z z press the [ ] button.
z z
[ ] button.
• Rotation is not possible when [Auto Rotate] is set to [Off] (
).
Deactivating Auto Rotation
Follow these steps to deactivate automatic image rotation, which rotates images based on the current camera orientation.
z z
] button, choose [Auto
Rotate] on the [ ] tab, and then choose
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
• Images cannot be rotated (
= 65 ) when you set [Auto Rotate] to
[Off]. Additionally, images already rotated will be displayed in the original orientation.
65
Still Images
Tagging Images as Favorites
Movies
You can organize images by tagging them as favorites. By choosing a category in filtered playback, you can restrict the following operations to all of those images.
•
), “Viewing Slideshows” ( = 59 ), “Protecting Images”
= 63 ), “Adding Images to the Print List
(DPOF)” ( = 116 ), “Adding Images to a Photobook” (
z z z
[ ] in the menu (
[Tagged as Favorite] is displayed.
z z and choose [ ] again, and then press the [ ] button.
Using the Menu
1
Choose [Favorites].
z z ] button and choose
[Favorites] on the [ ] tab ( = 21
).
2
Choose an image.
z z image, and then press the [ ] button.
[ ] is displayed.
z z z again. [ ] is no longer displayed.
z images.
3
Finish the setup process.
z z ] button. A confirmation message is displayed.
z z and then press the [ ] button.
• Images will not be tagged as favorites if you switch to Shooting mode or turn the camera off before finishing the setup process in step 3.
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
66
Editing Still Images
•
–
) is only available when the memory card has sufficient free space.
Still Images
Resizing Images
Save a copy of images at a lower number of recording pixels.
1
Choose [Resize].
z z ] button and choose
[Resize] on the [ ] tab (
).
2
Choose an image.
z z image, and then press the [ ] button.
3
Choose an image size.
z z z size, and then press the [ ] button.
[Save new image?] is displayed.
4
Save the new image.
z z z and then press the [ ] button.
The image is now saved as a new file.
5
Review the new image.
z z ] button. [Display new image?] is displayed.
z z z and then press the [ ] button.
The saved image is now displayed.
• Editing is not possible for images shot at a recording pixel setting of
[ ] or [ ] (
).
• Images cannot be resized to a higher number of recording pixels.
Still Images
Correcting Image Brightness (i-Contrast)
Excessively dark image areas (such as faces or backgrounds) can be detected and automatically adjusted to the optimal brightness. Insufficient overall image contrast is also automatically corrected, to make subjects stand out better. Choose from four correction levels, and then save the image as a separate file.
1
Choose [i-Contrast].
z z
] button, and then choose [i-Contrast] on the [ ] tab
2
Choose an image.
z z image, and then press the [ ] button.
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
67
3
Choose an option.
z z option, and then press the [ ] button.
4
Save as a new image and review.
z z
(
).
• For some images, correction may be inaccurate or may cause images to appear grainy.
• Images may look grainy after repeated editing using this function.
• If [Auto] does not produce the expected results, try correcting images using
[Low], [Medium], or [High].
Still Images
Correcting Red-Eye
Automatically corrects images affected by red-eye. You can save the corrected image as a separate file.
1
Choose [Red-Eye Correction].
z z
] button, and then choose [Red-Eye Correction] on the [ ]
2
Choose an image.
z z image.
3
Correct the image.
z z z z corrected, and frames are displayed around corrected image areas.
z z
Follow the steps in “Magnifying Images”
4
Save as a new image and review.
z z
[New File], and then press the [ ] button.
z z z z
• Some images may not be corrected accurately.
• To overwrite the original image with the corrected image, choose
[Overwrite] in step 4. In this case, the original image will be erased.
• Protected images cannot be overwritten.
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
68
Wi-Fi Functions
Send images wirelessly from the camera to a variety of compatible devices, and use the camera with Web services
•
Before using Wi-Fi, be sure to read “Wi-Fi (Wireless LAN) Precautions” ( = 141 ).
Available Wi-Fi Features ..................................
Sending Images to a Smartphone ..................
Sending Images to an NFC-Compatible
Smartphone ...........................................................
Adding a Smartphone ...........................................
Using Another Access Point ..................................
Previous Access Points .........................................
Saving Images to a Computer .........................
Preparing to Register a Computer ........................
Saving Images to a Connected Computer ............
Sending Images to a Registered Web
Service .............................................................
Registering Web Services .....................................
Uploading Images to Web Services ......................
Printing Images Wirelessly from a Connected Printer ........................................
Sending Images to Another Camera ..............
Image Sending Options ...................................
Sending Multiple Images .......................................
Notes on Sending Images .....................................
Choosing the Number of Recording Pixels
(Image Size) ..........................................................
Adding Comments .................................................
(Image Sync) ...................................................
Initial Preparations ................................................
Sending Images ....................................................
Using a Smartphone to View Camera Images and Control the Camera .................................
Geotagging Images on the Camera ......................
Shooting Remotely ................................................
Editing or Erasing Wi-Fi Settings ...................
Editing Connection Information .............................
Changing the Camera Nickname ..........................
Returning the Wi-Fi Settings to Default .................
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
69
Available Wi-Fi Features
You can send and receive images and control the camera remotely by connecting it to these devices and services via Wi-Fi.
• Smartphones and Tablets
Send images to smartphones and tablet computers that have Wi-Fi functions. You can also shoot remotely and geotag your shots from a smartphone or tablet. For convenience in this manual, smartphones, tablets, and other compatible devices are collectively referred to as
“smartphones”.
• Computer
Use software to save camera images to a computer connected via Wi-Fi.
• Web Services
Add your account information to the camera for CANON iMAGE
GATEWAY online photography service or other Web services to send camera images to the services. Unsent images on the camera can also be sent to a computer or Web service via CANON iMAGE GATEWAY.
• Printers
Send images wirelessly to a PictBridge-compatible printer (supporting
DPS over IP) to print them.
• Another Camera
Send images wirelessly between Wi-Fi-compatible Canon cameras.
Sending Images to a Smartphone
There are several ways to connect the camera to a smartphone and send images.
•
)
Simply touch an NFC-compatible Android smartphone (OS version 4.0 or later) against the camera to connect the devices.
• Connect via the Wi-Fi menu (
)
You can connect the camera to a smartphone as you would connect it to a computer or other device. Multiple smartphones can be added.
Before connecting to the camera, you must install the free dedicated
Camera Connect app on the smartphone. For details on this application
(supported smartphones and included functions), refer to the Canon website.
• Canon Wi-Fi-compatible camera users who connect their camera to a smartphone via Wi-Fi should consider switching from the CameraWindow mobile app to the Camera Connect mobile app.
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
70
Sending Images to an NFC-Compatible
Smartphone
Use an Android (OS version 4.0 or later) smartphone’s NFC to simplify the process of installing Camera Connect and connecting to the camera.
Operation when devices are initially connected via NFC varies depending on the camera mode when the devices are touched together.
• If the camera is off or in Shooting mode when the devices are touched together, you can choose and send images on the image selection screen. Once the devices are connected, you can also shoot remotely and geotag your shots (
). It’s easy to reconnect to recent devices, which are listed in the Wi-Fi menu.
• If the camera is in Playback mode when the devices are touched together, you can choose and send images from the index display shown for image selection.
Follow the instructions in the following section for NFC-initiated connection to a camera that is off or in Shooting mode.
Connecting via NFC When Camera Is Off or in Shooting
Mode
1
Install Camera Connect.
z z touch the devices’ N-Marks ( ) together to start Google Play on the smartphone automatically. Once the Camera Connect download page is displayed, download and install the app.
2
Establish the connection.
z z z
Shooting mode.
z with Camera Connect installed against the camera’s N-Mark.
z z z z displayed, press the [ ][ ] buttons to choose [OK], and then press the [ ] button.
z z z smartphone.
The devices are connected automatically.
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index 3
Adjust the privacy setting.
z z
[ ][ ] buttons to choose [Yes], and then press the [ ] button.
z z browse, import, or geotag images on the camera or shoot remotely.
71
4
Send an image.
z z
[Select and send], and then press the [ ] button.
z z
[Select], and then press the [ ] button.
z z an image to send, press the [ ] button to mark it as selected ([ ]), and then press the [ ] button.
z z z and then press the [ ] button.
z
[Send], and then press the [ ] button.
z z the image is sent, and the image transfer screen is displayed again.
z z
[ ] button, press the [ ][ ] buttons on the confirmation screen to choose
[OK], and then press the [ ] button. You can also use the smartphone to end the connection.
• When using NFC, keep the following points in mind.
- Avoid strong impact between the camera and smartphone. This may damage the devices.
- Depending on the smartphone, the devices may not recognize each other immediately. In this case, try holding the devices together in slightly different positions. If connection is not established, keep the devices together until the camera screen is updated.
- If you attempt connection when the camera is off, a message may be displayed on the smartphone reminding you to turn on the camera. If so, turn the camera on and touch the devices together again.
- Do not place other objects between the camera and smartphone.
Also, note that camera or smartphone covers or similar accessories may block communication.
• All images in the camera can be viewed from the connected smartphone when you choose [Yes] in step 3. To keep camera images private, so that they cannot be viewed from the smartphone, choose [No] in step 3.
• Once you have registered a smartphone, you can change privacy
settings for it on the camera ( = 94 ).
• Connections require that a memory card be in the camera.
• You can also change the camera nickname on the screen in step 2 (
• Not all NFC-compatible smartphones have an N-Mark ( ). For details, refer to the smartphone user manual.
• You can also send multiple images at once and change the image size before sending (
).
• You can send the current image by choosing [Send this image] on the screen in step 4.
•
To disable NFC connections, choose MENU ( = 21
) ► [ ] tab ► [Wireless settings] ► [Wi-Fi Settings] ► [NFC] ► [Off].
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
72
Connecting via NFC When Camera Is in Playback Mode
z z ] button to turn the camera on.
z z
Connect installed ( = 71 ) against the
camera’s N-Mark ( ).
z z an image to send, and then press the [ ] button. [ ] is displayed.
z z z again. [ ] is no longer displayed.
z images.
z z the [ z
] button.
z Press the [ ][ ] buttons to choose [OK], z and then press the [ ] button.
z
[Send], and then press the [ ] button.
z z
• If during connection a message on the camera requests you to enter
the nickname, follow step 2 in “Sending Images to an NFC-Compatible
Smartphone” ( = 71 ) to enter it.
• The camera does not keep a record of smartphones you connect to via NFC in
Playback mode.
• You can preset images to transfer at your desired size (
Adding a Smartphone
These steps show how to use the camera as an access point, but you can also use an existing access point (
).
1
Install Camera Connect.
z z
Connect in the App Store and download and install the app.
z z
Connect in Google Play and download and install the app.
2
Access the Wi-Fi menu.
z z z z displayed, choose [OK] (
).
3
Choose [ ].
z z
[ ], and then press the [ ] button.
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
4
Choose [Add a Device].
z z a Device], and then press the [ ] button.
73
z z displayed.
5
Connect the smartphone to a network.
z z choose the SSID (network name) displayed on the camera to establish a connection.
z z displayed on the camera.
6
Start Camera Connect.
z z smartphone.
7
Select the camera to connect to.
z z displayed on the smartphone, choose the camera to begin pairing.
8
Adjust the privacy setting.
z z z and then press the [ ] button.
You can now use the smartphone to browse, import, or geotag images on the camera or shoot remotely.
9
Send an image.
z z
[Select and send], and then press the [ ] button.
z z z
[Select], and then press the [ ] button.
Press the [ ][ ][ ][ ] buttons to choose an image to send, press the [ ] button to mark it as selected ([ ]), and then press the [ ] button.
z z and then press the [ ] button.
z z Press the [ ][ ][ ][ ] buttons to choose
[Send], and then press the [ ] button.
z z z the image is sent, and the image transfer screen is displayed again.
z ] button, press the [ ][ ] buttons on the confirmation screen to choose [OK], and then press the [ ] button. You can also use the smartphone to end the connection.
z z above procedure starting from step 1.
• All images in the camera can be viewed from the connected smartphone when you choose [Yes] in step 8. To keep camera images private, so that they cannot be viewed from the smartphone, choose [No] in step 8.
• Once you have registered a smartphone, you can change privacy
settings for it on the camera ( = 94 ).
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
74
• Connections require that a memory card be in the camera.
• Once you have connected to devices via the Wi-Fi menu, recent destinations will be listed first when you access the Wi-Fi menu. You can easily connect again by pressing the [ ][ ] buttons to choose the device and then pressing the [ ] button. To add a new device, display the device selection screen by pressing the [ ][ ] buttons, and then configure the setting.
• If you prefer not to display recent target devices, choose MENU (
[ ] tab ► [Wireless settings] ► [Wi-Fi Settings] ► [Target History] ► [Off].
•
To connect without entering a password in step 5, choose MENU ( = 21
)
► [ ] tab ► [Wireless settings] ► [Wi-Fi Settings] ► [Password] ► [Off].
[Password] is no longer displayed on the SSID screen (in step 4).
• You can also send multiple images at once and change the image size before
).
• You can send the current image by choosing [Send this image] on the screen in step 9.
Using Another Access Point
When connecting the camera to a smartphone through the Wi-Fi menu, you can also use an existing access point.
1
Prepare for the connection.
z z
by following steps 1 – 4 in “Adding a
2
Connect the smartphone to the access point.
3
Choose [Switch Network].
z z
[Switch Network], and then press the [ ] button.
z z displayed.
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
75
4
Connect to the access point.
z z connect to the access point as described
in steps 5 – 8 in “Using WPS-Compatible
z z
2 – 4 in “Connecting to Listed Access
Points” ( = 80 ) to connect to the
access point.
5
Select the camera to connect to.
z z displayed on the smartphone, choose the camera to begin pairing.
6
Configure the privacy settings and send images.
z z
Smartphone” ( = 73 ) to configure the
privacy settings and send images.
Previous Access Points
You can reconnect to any previous access points automatically by following
step 4 in “Adding a Smartphone” ( = 73 ).
• To use the camera as an access point, choose [Switch Network] on the screen displayed when you establish a connection, and then choose
[Camera Access Point Mode].
• To switch access points, choose [Switch Network] on the screen displayed when you establish a connection, and then follow the
procedure in “Using Another Access Point” ( = 75 ) from step 4.
Saving Images to a Computer
Preparing to Register a Computer
For details on computers that you can connect the camera to via Wi-Fi, system requirements, and other compatibility information (including support in new operating systems), visit the Canon website.
• Windows 7 Starter and Home Basic editions are not supported.
• Windows 7 N (European version) and KN (South Korean version) require a separate download and installation of Windows Media
Feature Pack. For details, check the following website. http://go.microsoft.com/fwlink/?LinkId=159730
Installing the Software
Windows 7 and Mac OS X 10.8 are used here for the sake of illustration.
1
Download the software.
z z access http://www.canon.com/icpd/.
z z z z
2
Install the files.
z z on-screen instructions to complete the installation process.
z z depending on computer performance and the Internet connection.
z z after installation.
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
76
• Internet access is required, and any ISP account charges and access fees must be paid separately.
• To uninstall the software, follow these steps.
- Windows: Select [Start] menu ► [All Programs] ► [Canon Utilities], and then choose the software for uninstallation.
- Mac OS: In the [Canon Utilities] folder within the [Applications] folder, drag the folder of the software for uninstallation to the Trash, and then empty the
Trash.
Configuring the Computer for a Wi-Fi Connection
(Windows Only)
On a computer running Windows, configure the following settings before connecting the camera to the computer wirelessly.
1
Confirm that the computer is connected to an access point.
z z connection, refer to the computer user manual.
2
Configure the setting.
z z
► [All Programs] ► [Canon Utilities] ►
[CameraWindow] ► [Wi-Fi connection setup].
z z on-screen instructions and configure the setting.
• The following Windows settings are configured when you run the utility in step 2.
- Turn on media streaming.
This will enable the camera to see (find) the computer to access via Wi-Fi.
- Turn on network discovery.
This will enable the computer to see (find) the camera.
- Turn on ICMP (Internet Control Message Protocol).
This allows you to check the network connection status.
- Enable Universal Plug & Play (UPnP).
This will enable network devices to detect each other automatically.
• Some security software may prevent you from completing the settings as described here. Check the settings of your security software.
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
77
Saving Images to a Connected Computer
Connect to your access point via Wi-Fi as follows.
Also refer to the access point user manual.
Confirming Access Point Compatibility
Confirm that the Wi-Fi router or base station conforms to the Wi-Fi
standards in “Camera” ( = 135 ).
Connection methods vary depending on whether the access point supports
Wi-Fi Protected Setup (WPS,
) or not (
). For non-WPS access points, check the following information.
• Network name (SSID/ESSID)
The SSID or ESSID for the access point you use. Also called the “access point name” or “network name”.
• Network authentication / data encryption (encryption method / encryption mode)
The method for encrypting data during wireless transmission. Check which security setting is used: WPA2-PSK (AES), WPA2-PSK (TKIP),
WPA-PSK (AES), WPA-PSK (TKIP), WEP (open system authentication), or no security.
• Password (encryption key / network key)
The key used when encrypting data during wireless transmission. Also called the “encryption key” or “network key”.
• Key index (transmit key)
The key set when WEP is used for network authentication / data encryption. Use “1” as the setting.
• If system administrator status is needed to adjust network settings, contact the system administrator for details.
• These settings are very important for network security. Exercise adequate caution when changing these settings.
• For information on WPS compatibility and for instructions on checking settings, refer to the access point user manual.
• A router is a device that creates a network (LAN) structure for connecting multiple computers. A router that contains an internal Wi-Fi function is called a “Wi-Fi router”.
• This guide refers to all Wi-Fi routers and base stations as “access points”.
• If you use MAC address filtering on your Wi-Fi network, be sure to add the camera’s MAC address to your access point. You can check your camera’s
MAC address by choosing MENU (
= 21 ) ► [ ] tab ► [Wireless settings]
► [Wi-Fi Settings] ► [Check MAC Address].
Using WPS-Compatible Access Points
WPS makes it easy to complete settings when connecting devices over Wi-
Fi. You can use either Push Button Configuration Method or PIN Method for settings on a WPS supported device.
1
Confirm that the computer is connected to an access point.
z z connection, refer to the device and access point user manuals.
2
Access the Wi-Fi menu.
z z
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index z z displayed, press the [ ][ ] buttons to choose [OK], and then press the [ ] button.
78
3
Choose [ ].
z z
[ ], and then press the [ ] button.
4
Choose [Add a Device].
z z a Device], and then press the [ ] button.
5
Choose [WPS Connection].
z z
[WPS Connection], and then press the
[ ] button.
6
Choose [PBC Method].
z z
Method], and then press the [ ] button.
7
Establish the connection.
z z connection button for a few seconds.
z z z go to the next step.
z and lists devices connected to it on the
[Select a Device] screen.
8
9
Choose the target device.
z z target device name, and then press the
[ ] button.
Install a driver (first Windows connection only).
z z camera, click the Start menu on the computer, click [Control Panel], and then click [Add a device].
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
79
z z z z z z the camera and computer connection is enabled, the AutoPlay screen will be displayed. Nothing will be displayed on the camera screen.
10
Display CameraWindow.
z z clicking [Downloads Images From Canon
Camera].
z z displayed when a Wi-Fi connection is established between the camera and computer.
11
Import images.
z z then click [Import Untransferred Images].
z z folder on the computer, in separate folders named by date.
z z after image import is complete.
z z use preinstalled or commonly available software compatible with images captured by the camera.
• Once you have connected to devices via the Wi-Fi menu, recent destinations will be listed first when you access the Wi-Fi menu. You can easily connect again by pressing the [ ][ ] buttons to choose the device and then pressing the [ ] button. To add a new device, display the device selection screen by pressing the [ ][ ] buttons, and then configure the setting.
•
If you prefer not to display recent target devices, choose MENU ( = 21
) ►
[ ] tab ► [Wireless settings] ► [Wi-Fi Settings] ► [Target History] ► [Off].
• You can also change the camera nickname on the screen in step 2 (
• When the camera is connected to a computer, the camera screen is blank.
• Mac OS: If CameraWindow is not displayed, click the [CameraWindow] icon in the Dock.
• To disconnect from the camera, turn off the camera.
• If you chose [PIN Method] in step 6, a PIN code will be displayed on the screen. Be sure to set this code in the access point. Choose a device in the
[Select a Device] screen. For further details, refer to the user manual included with your access point.
Connecting to Listed Access Points
1
View the listed access points.
z z
as described in steps 1 – 4 of “Using
2
Choose an access point.
z z network (access point), and then press the [ ] button.
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
80
3
Enter the access point password.
z z keyboard, and then enter the password
(
).
z z
[Next], and then press the [ ] button.
4
Choose [Auto].
z z z
[Auto], and then press the [ ] button.
z follow the procedure from step 8 in
“Using WPS-Compatible Access Points”
• To determine the access point password, check on the access point itself or refer to the user manual.
• If no access points are detected even after you choose [Refresh] in step 2 to update the list, choose [Manual Settings] in step 2 to complete access point settings manually. Follow on-screen instructions and enter an SSID, security settings, and a password.
• When you use an access point that you have already connected to for connecting to another device, [*] is displayed for the password in step 3. To use the same password, press the [ ][ ] buttons to choose [Next], and then press the [ ] button.
Previous Access Points
You can reconnect to any previous access points automatically by following
step 4 in “Using WPS-Compatible Access Points” ( = 78 ).
• To connect to a device via an access point, confirm that the target device is already connected to the access point, and then follow the procedure
from step 8 in “Using WPS-Compatible Access Points” ( = 78 ).
• To switch access points, choose [Switch Network] on the screen displayed when you establish a connection, and then either follow the
procedure in “Using WPS-Compatible Access Points” ( = 78 ) from
step 5 or the procedure in “Connecting to Listed Access Points” ( = 80 )
from step 2.
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
81
Sending Images to a Registered Web
Service
Registering Web Services
Use a smartphone or computer to add to the camera Web services that you want to use.
• A smartphone or computer with a browser and Internet connection is required to complete camera settings for CANON iMAGE GATEWAY and other Web services.
• Check the CANON iMAGE GATEWAY website for details on browser
(Microsoft Internet Explorer, etc.) requirements, including settings and version information.
• For information on countries and regions where CANON iMAGE GATEWAY is available, visit the Canon website (http://www.canon.com/cig/).
• You must have an account with Web services other than CANON iMAGE
GATEWAY if you desire to use them. For further details, check the websites for each Web service you want to register.
• Separate ISP connection and access point fees may be applicable.
• CANON iMAGE GATEWAY also provides user guides for downloading.
Registering CANON iMAGE GATEWAY
Link the camera and CANON iMAGE GATEWAY by adding CANON iMAGE
GATEWAY as a destination Web service on the camera. Note that you will need to enter an email address used on your computer or smartphone to receive a notification message for completing linkage settings.
1
Access the Wi-Fi menu.
z z
2 z z displayed, press the [ ][ ] buttons to choose [OK], and then press the [ ] button.
Choose [ ].
z z
[ ], and then press the [ ] button.
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
3
Accept the agreement to enter an email address.
z z
[ ][ ] buttons to choose [I Agree], and then press the [ ] button.
82
4
Establish a connection with an access point.
z z
in steps 5 – 7 in “Using WPS-Compatible
Access Points” ( = 78 ) or in steps 2 – 4
in “Connecting to Listed Access Points”
5
Enter your email address.
z z iMAGE GATEWAY via the access point, a screen is displayed for entering an email address.
z z
[ ][ ] buttons to choose [Next], and then press the [ ] button.
6
Enter a four-digit number.
z z press the [ ][ ] buttons to choose
[Next], and then press the [ ] button.
z z when setting up linkage with CANON iMAGE GATEWAY in step 8.
7
Check for the notification message.
z z
CANON iMAGE GATEWAY, you will receive a notification message at the email address entered in step 5.
z z which indicates that notification has been sent.
z z ] now changes to [ ].
8
Access the page in the notification message and complete camera link settings.
z z access the page linked in the notification message.
z z settings on the camera link settings page.
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
83
9
Complete CANON iMAGE
GATEWAY settings on the camera.
z z z
[ ], and then press the [ ] button.
z
) and CANON iMAGE
GATEWAY are now added as destinations.
z z as needed. In this case, follow the
instructions from step 2 in “Registering
• Make sure initially that your computer or smartphone mail application is not configured to block email from relevant domains, which may prevent you from receiving the notification message.
•
You can also change the camera nickname on the screen in step 1 ( = 82
).
• Once you have connected to devices via the Wi-Fi menu, recent destinations will be listed first when you access the menu. Press the [ ][ ] buttons to access the device selection screen and then configure the setting.
Registering Other Web Services
You can also add Web services besides CANON iMAGE GATEWAY to the camera.
1
Log in to CANON iMAGE
GATEWAY and access the camera link settings page.
z z http://www.canon.com/cig/ to visit
CANON iMAGE GATEWAY.
2
Configure the Web service you want to use.
z z the Web service settings screen.
z z complete settings for Web services you want to use.
3
Choose [ ].
z z z z z
[ ], and then press the [ ] button.
z updated.
• If any configured settings change, follow these steps again to update the camera settings.
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
84
Uploading Images to Web Services
1
Access the Wi-Fi menu.
z z
2
Choose the destination.
z z the icon of the Web service to connect to, and then press the [ ] button.
z z are used with a Web service, choose the desired item on the [Select Recipient] screen by pressing the [ ][ ] buttons, and then press the [ ] button.
3
Send an image.
z z
[Select and send], and then press the [ ] button.
z z
[Select], and then press the [ ] button.
z z an image to send, press the [ ] button to mark it as selected ([ ]), and then press the [ ] button.
z z z and then press the [ ] button.
z
[Send], and then press the [ ] button.
z z terms of service, choose [I Agree], and press the [ ] button.
z z playback screen once [OK] is displayed after the image is sent.
• Connections require that a memory card with saved images be in the camera.
• You can also send multiple images at once, resize images, and add comments before sending (
• You can send the current image by choosing [Send this image] on the screen in step 3.
• To view images uploaded to CANON iMAGE GATEWAY on a smartphone, try the dedicated Canon Online Photo Album app. Download and install the
Canon Online Photo Album app for iPhones or iPads from the App Store or for
Android devices from Google Play.
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
85
Printing Images Wirelessly from a
Connected Printer
Connect the camera to a printer via Wi-Fi to print as follows.
These steps show how to use the camera as an access point, but you can
also use an existing access point ( = 75 ).
1
Access the Wi-Fi menu.
z z
2
Choose [ ].
z z
[ ], and then press the [ ] button.
3
Choose [Add a Device].
z z a Device], and then press the [ ] button.
z z displayed.
4
Connect the printer to the network.
z z choose the SSID (network name) displayed on the camera to establish a connection.
z z displayed on the camera.
5
Choose the printer.
z z printer name, and then press the [ ] button.
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
86
6
Choose an image to print.
z z z image.
z press the [ ] button again.
z z z
[Print], and then press the [ ] button.
z
z z button, press the [ ][ ] buttons on the confirmation screen to choose [OK], and then press the [ ] button.
• Connections require that a memory card with saved images be in the camera.
• Once you have connected to devices via the Wi-Fi menu, recent destinations will be listed first when you access the Wi-Fi menu. You can easily connect again by pressing the [ ][ ] buttons to choose the device and then pressing the [ ] button. To add a new device, display the device selection screen by pressing the [ ][ ] buttons, and then configure the setting.
• If you prefer not to display recent target devices, choose MENU (
[ ] tab ► [Wireless settings] ► [Wi-Fi Settings] ► [Target History] ► [Off].
•
To connect without entering a password in step 4, choose MENU ( = 21
)
► [ ] tab ► [Wireless settings] ► [Wi-Fi Settings] ► [Password] ► [Off].
[Password] is no longer displayed on the SSID screen (in step 3).
•
To use another access point, follow steps 3 – 4 in “Using Another Access
Sending Images to Another Camera
Connect two cameras via Wi-Fi and send images between them as follows.
• Only Canon-brand cameras equipped with a Wi-Fi function can be connected to wirelessly. You cannot connect to a Canon-brand camera that does not have a Wi-Fi function, even if it supports Eye-Fi/FlashAir
Cards.
1
Access the Wi-Fi menu.
2 z z
Choose [ ].
z z
[ ], and then press the [ ] button.
3
Choose [Add a Device].
z z z a Device], and then press the [ ] button.
z too.
z z added when [Start connection on target camera] is displayed on both camera screens.
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
87
4
Send an image.
z z
[Select and send], and then press the [ ] button.
z z z
[Select], and then press the [ ] button.
z an image to send, press the [ ] button to mark it as selected ([ ]), and then press the [ ] button.
z z and then press the [ ] button.
z z
[Send], and then press the [ ] button.
z z the image is sent, and the image transfer screen is displayed again.
z z
[ ] button, press the [ ][ ] buttons on the confirmation screen to choose
[OK], and then press the [ ] button.
• Connections require that a memory card be in the camera.
• Once you have connected to devices via the Wi-Fi menu, recent destinations will be listed first when you access the Wi-Fi menu. You can easily connect again by pressing the [ ][ ] buttons to choose the device and then pressing the [ ] button. To add a new device, display the device selection screen by pressing the [ ][ ] buttons, and then configure the setting.
•
If you prefer not to display recent target devices, choose MENU ( = 21
) ►
[ ] tab ► [Wireless settings] ► [Wi-Fi Settings] ► [Target History] ► [Off].
• You can also send multiple images at once and change the image size before sending (
).
• You can send the current image by choosing [Send this image] on the screen in step 4.
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
88
Image Sending Options
You can choose multiple images to send at once and change the image recording pixel setting (size) before sending. Some Web services also enable you to annotate the images you send.
Sending Multiple Images
On the image transfer screen, specify a range of images to send, or send only images tagged as favorites.
1
Choose [Select and send].
z z
[ ][ ] buttons to choose [Select and send], and then press the [ ] button.
2
Choose a selection method.
z z selection method.
Selecting a Range
1
Choose [Select Range].
z z
Images” ( = 89 ), choose [Select
Range] and press the [ ] button.
2
Choose images.
z z
z z
[ ][ ][ ][ ] buttons to choose [Incl.
Movies], and then press the [ ] button to mark the option as selected ( ).
z z
[OK], and then press the [ ] button.
3
Send the images.
z z
[Send], and then press the [ ] button.
Sending Favorite Images
Send only images tagged as favorites (
).
1
Choose [Favorite Images].
z z
Images” (
), choose [Favorite
Images] and press the [ ] button.
z z displayed. If you prefer not to include an image, choose the image and press the
[ ] button to remove [ ].
z z z z
] button.
Press the [ ][ ] buttons to choose [OK], and then press the [ ] button.
2
Send the images.
z z
[Send], and then press the [ ] button.
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
89
• In step 1, [Favorite Images] is not available unless you have tagged images as favorites.
Notes on Sending Images
• Depending on the condition of the network you are using, it may take a long time to send movies. Be sure to keep an eye on the camera battery level.
• Web services may limit the number of images or length of movies you can send.
• When sending movies to smartphones, note that the supported image quality varies depending on the smartphone. For details, refer to the smartphone user manual.
• On the screen, wireless signal strength is indicated by the following icons.
[ ] high, [ ] medium, [ ] low, [ ] weak
• Sending images to Web services will take less time when resending images you have already sent that are still on the CANON iMAGE
GATEWAY server.
Choosing the Number of Recording Pixels
(Image Size)
On the image transfer screen, choose [ ] by pressing the [ ][ ] buttons, and then press the [ ] button. On the screen displayed, choose the recording pixel setting (image size) by pressing the [ ][ ] buttons, and then press the [ ] button.
• To send images at original size, select [No] as the resizing option.
• Choosing [ ] will resize images that are larger than the selected size before sending.
• Movies cannot be resized.
•
Image size can also be configured in MENU ( = 21
) ► [ ] tab ► [Wireless settings] ► [Wi-Fi Settings] ► [Resize for Sending].
Adding Comments
Using the camera, you can add comments to images that you send to e-mail addresses, social networking services, etc. The number of characters and symbols that can be entered may differ depending on the Web service.
1
Access the screen for adding comments.
z z
[ ] by pressing the [ ][ ][ ][ ] buttons, and then press the [ ] button.
2
Add a comment (
).
3
Send the image.
• When a comment is not entered, the comment set in CANON iMAGE
GATEWAY is automatically sent.
• You can also annotate multiple images before sending them. The same comment is added to all images sent together.
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
90
Sending Images Automatically
(Image Sync)
Images on the memory card that have not been transferred already can be sent to a computer or Web services via CANON iMAGE GATEWAY.
Note that images cannot be sent only to Web services.
Initial Preparations
Preparing the Camera
Register [ ] as the destination. On the destination computer, you will install and configure Image Transfer Utility, free software compatible with Image
Sync.
1
Add [ ] as a destination.
z z
“Registering CANON iMAGE GATEWAY”
z z destination, log in to CANON iMAGE
GATEWAY (
), select your camera model, access the Web service settings screen, and choose the destination
Web service in Image Sync settings.
For details, refer to CANON iMAGE
GATEWAY Help.
2
Choose the type of images to send (only when sending movies with images).
z z ] button, choose
[Wireless settings] on the [ ] tab, and then choose [Wi-Fi Settings] (
).
z z
[Image Sync], and then press the [ ][ ] buttons to choose [Stills/Movies].
Preparing the Computer
Install and configure the software on the destination computer.
1
Install Image Transfer Utility.
z z z
connected to the Internet ( = 76
).
Image Transfer Utility can also be downloaded from the Image Sync settings page of CANON iMAGE
2
Register the camera.
z z z and then click [Add new camera].
z then click [Add new camera].
z z
GATEWAY is displayed. Choose the camera from which images are to be sent.
z z computer is ready to receive images, the icon changes to [ ].
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
91
Sending Images
Images sent from the camera are automatically saved to the computer.
If the computer that you intend to send images to is turned off, the images will be stored temporarily on the CANON iMAGE GATEWAY server. Stored images are regularly erased, so make sure to turn on the computer and save the images.
1
Send images.
z z
to Web Services” ( = 85 ) and choose
[ ].
z z
2
Save the images to the computer.
z z computer when you turn it on.
z z services from the CANON iMAGE
GATEWAY server, even if the computer is off.
• When sending images, you should use a fully charged battery pack.
• Even if images were imported to the computer through a different method, any images not sent to the computer via CANON iMAGE GATEWAY will be sent to the computer.
• Sending is faster when the destination is a computer on the same network as the camera, because images are sent via the access point instead of
CANON iMAGE GATEWAY. Note that images stored on the computer are sent to CANON iMAGE GATEWAY, so the computer must be connected to the
Internet.
Viewing Images Sent via Image Sync on a Smartphone
By installing the Canon Online Photo Album (Canon OPA) app, you can use your smartphone to view and download images sent via Image Sync while they are stored temporarily on the CANON iMAGE GATEWAY server.
In preparation, enable smartphone access as follows.
•
Make sure you have completed the settings described in “Preparing the
• Download and install the Canon Online Photo Album app for iPhones or iPads from the App Store or for Android devices from Google Play.
• Log in to CANON iMAGE GATEWAY (
), select your camera model, access the Web service settings screen, and enable viewing and downloading from a smartphone in the Image Sync settings. For details, refer to CANON iMAGE GATEWAY Help.
• Once images stored temporarily on the CANON iMAGE GATEWAY server have been deleted, they can no longer be viewed.
• Images you sent before enabling smartphone viewing and downloading in Image Sync settings cannot be accessed this way.
• For Canon Online Photo Album instructions, refer to Canon Online Photo
Album Help.
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
92
Using a Smartphone to View Camera
Images and Control the Camera
You can do the following with the dedicated smartphone app Camera
Connect.
• Browse images on the camera and save them to the smartphone
• Geotag images on the camera (
)
•
• In camera settings, the smartphone must be allowed to view camera
Geotagging Images on the Camera
GPS data recorded on a smartphone using the dedicated Camera Connect application can be added to images on the camera. Images are tagged with information including the latitude, longitude, and elevation.
• Before shooting, make sure the date and time and your home time zone are
set correctly, as described in “Setting the Date and Time” ( = 12 ). Also follow
the steps in “World Clock” ( = 99 ) to specify any shooting destinations in
other time zones.
• Others may be able to locate or identify you by using location data in your geotagged still images or movies. Be careful when sharing these images with others, as when posting images online where many others can view them.
Shooting Remotely
As you check a shooting screen on your smartphone, you can use it to shoot remotely.
1
Secure the camera.
z z camera lens will come out. Lens motion from zooming may also move the camera out of position. Keep the camera still by mounting it on a tripod or taking other measures.
2
Connect the camera and smartphone (
).
z z
3
Choose remote shooting.
z z choose remote shooting.
z z your fingers away from the lens, and make sure no objects will obstruct it.
z z shooting, a live image from the camera will be displayed on the smartphone.
z z the camera, and all operations except pressing the power button are disabled.
4
Shoot.
z z
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
93
• The camera works in [ ] mode during remote shooting. However, some FUNC. and MENU settings you have configured in advance may be changed automatically.
• Movie shooting is not available.
• Any jerky subject motion shown on the smartphone due to the connection environment will not affect recorded images.
• No AF frames are displayed. Capture a test image to check the focus.
• Captured images are not transferred to the smartphone. Use the smartphone to browse and import images from the camera.
Editing or Erasing Wi-Fi Settings
Edit or erase Wi-Fi settings as follows.
Editing Connection Information
1
Access the Wi-Fi menu and choose a device to edit.
z z z z the device selection screen, press the
[ ][ ][ ][ ] buttons to choose the icon of a device to edit, and then press the
[ ] button.
2
Choose [Edit a Device].
z z a Device], and then press the [ ] button.
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
3
Choose a device to edit.
z z device to edit, and then press the [ ] button.
94
Configurable Items
[Change Device Nickname] (
)
[Erase Connection Info] (
4
Choose an item to edit.
z z the item to edit, and then press the [ ] button.
z z device or service.
Connection
O
–
O
O
O
O
O
–
O
O
–
O
Web
Services
–
–
–
O : Configurable – : Not configurable
Changing a Device Nickname
You can change the device nickname (display name) that is displayed on the camera.
z z
Information” ( = 94 ), choose [Change
Device Nickname] and press the [ ] button.
z z button. Use the keyboard displayed to enter a new nickname (
).
Erasing Connection Information
Erase connection information (information about devices that you have connected to) as follows.
z z
Information” ( = 94 ), choose [Erase
Connection Info] and press the [ ] button.
z z
[ ][ ] buttons to choose [OK], and then press the [ ] button.
z z
Changing the Camera Nickname
Change the camera nickname (displayed on connected devices) as desired.
1
Choose [Wireless settings].
z z
] button and choose
[Wireless settings] on the [ ] tab
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
2
Choose [Nickname].
z z
[Nickname], and then press the [ ] button.
95
3
Change the nickname.
z z keyboard (
nickname.
• A message is displayed if the nickname you enter begins with a symbol or space. Press the [ ] button and enter a different nickname.
• You can also change the nickname from the [Nickname] screen displayed when you first use Wi-Fi. In this case, select the text box, press the [ ] button to access the keyboard, and then enter a new nickname.
Returning the Wi-Fi Settings to Default
Return the Wi-Fi settings to default if you transfer ownership of the camera to another person, or dispose of it.
Resetting the Wi-Fi settings will also clear all Web service settings. Be sure that you want to reset all Wi-Fi settings before using this option.
1
Choose [Wireless settings].
z z
(
).
] button and choose
[Wireless settings] on the [ ] tab
2
Choose [Reset Settings].
z z
[Reset Settings], and then press the [ ] button.
3
Restore the default settings.
z z z and then press the [ ] button.
The Wi-Fi settings are now reset.
• To reset other settings (aside from Wi-Fi) to defaults, choose [Reset All] on the
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
96
Setting Menu
Customize or adjust basic camera functions for greater convenience
Adjusting Basic Camera Functions ................
Silencing Camera Operations ...............................
Adjusting the Volume ............................................
Hiding Hints and Tips ............................................
Date and Time .......................................................
World Clock ...........................................................
Lens Retraction Timing .........................................
Using Eco Mode ..................................................
Power-Saving Adjustment ...................................
Screen Brightness ...............................................
Hiding the Start-Up Screen .................................
Formatting Memory Cards ..................................
File Numbering ....................................................
Date-Based Image Storage .................................
Metric / Non-Metric Display .................................
Checking Certification Logos ..............................
Display Language ...............................................
Adjusting Other Settings .....................................
Restoring Default Camera Settings .....................
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
97
Adjusting Basic Camera Functions
Basic camera functions are configured on the [ ] tab of the MENU
(
). Customize commonly used functions as desired, for greater convenience.
Silencing Camera Operations
Silence camera sounds and movies as follows.
z z
Adjusting the Volume
Adjust the volume of individual camera sounds as follows.
z z z button.
z
[ ][ ] buttons to adjust the volume.
• Operation can also be silenced by holding down the [ ] button as you turn the camera on.
•
Sound is not played during movies ( = 56 ) if you mute camera sounds. To
restore sound during movies, press the [ ] button. Adjust volume with the
[ ][ ] buttons, as needed.
Hiding Hints and Tips
Hints and tips are normally shown when you choose FUNC. ( = 20 )
items. If you prefer, you can deactivate this information.
z z
[Off].
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
98
Date and Time
Adjust the date and time as follows.
z z z
[ ] button.
z item, and then press the [ ][ ] buttons to adjust the setting.
World Clock
To ensure that your shots will have the correct local date and time when you travel abroad, simply register the destination in advance and switch to that time zone. This convenient feature eliminates the need to change the Date/
Time setting manually.
Before using the world clock, be sure to set the date and time and your
home time zone, as described in “Setting the Date and Time” ( = 12 ).
1
Specify your destination.
z z
[ ] button.
z z
[ World], and then press the [ ] button.
z z destination.
z z choose [ ] by pressing the [ ][ ] buttons, and then choose [ ] by pressing the [ ][ ] buttons.
z z
2
Switch to the destination time zone.
z z
[ World], and then press the [ button.
] z z
• Adjusting the date or time while in [ ] mode (
update your [ Home] time and date.
Lens Retraction Timing
The lens is normally retracted for safety about one minute after you press the [ ] button in Shooting mode (
). To have the lens retracted immediately after you press the [ ] button, set the retraction timing to
[0 sec.].
z z choose [0 sec.].
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
99
Using Eco Mode
This function allows you to conserve battery power in Shooting mode. When the camera is not in use, the screen quickly darkens to reduce battery consumption.
1
Configure the setting.
z z
[On].
z z ] is now shown on the shooting
).
z z is not used for approximately two seconds; approximately ten seconds after darkening, the screen turns off.
The camera turns off after approximately three minutes of inactivity.
2
Shoot.
z z shooting when the screen is off but the lens is still out, press the shutter button halfway.
Power-Saving Adjustment
Adjust the timing of automatic camera and screen deactivation (Auto Power
Down and Display Off, respectively) as needed (
).
z z the [ ] button.
z z buttons to adjust it as needed.
• To conserve battery power, you should normally choose [On] for
[Auto Power Down] and [1 min.] or less for [Display Off].
• The [Display Off] setting is applied even if you set [Auto Power Down] to [Off].
• These power-saving functions are not available when you have set Eco mode
(
) to [On].
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
100
Screen Brightness
Adjust screen brightness as follows.
z z press the [ ][ ] buttons to adjust the brightness.
• For maximum brightness, press and hold the [ ] button for at least one second when the shooting screen is displayed or when in single-image display.
(This will override the [Disp. Brightness] setting on the [ ] tab.) To restore the original brightness, press and hold the [ ] button again for at least one second or restart the camera.
Hiding the Start-Up Screen
If you prefer, you can deactivate display of the start-up screen normally shown when you turn the camera on.
z z choose [Off].
Formatting Memory Cards
Before using a new memory card or a card formatted in another device, you should format the card with this camera.
Formatting erases all data on a memory card. Before formatting, copy images on the memory card to a computer, or take other steps to back them up.
1
Access the [Format] screen.
z z button.
2
Choose [OK].
z z
[Cancel], press the [ ][ ] buttons to choose [OK], and then press the [ ] button.
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
3
Format the memory card.
z z the [ ][ ] buttons to choose [OK], and then press the [ ] button.
z z card formatting complete] is displayed.
Press the [ ] button.
• Formatting or erasing data on a memory card only changes file management information on the card and does not erase the data completely. When transferring or disposing of memory cards, take steps to protect personal information if necessary, as by physically destroying cards.
101
• The total card capacity indicated on the formatting screen may be less than the advertised capacity.
Low-Level Formatting
Perform low-level formatting in the following cases: [Memory card error] is displayed, the camera is not working correctly, card image reading/writing is slower, continuous shooting is slower, or movie recording suddenly stops.
Low-level formatting erases all data on a memory card. Before low-level formatting, copy images on the memory card to a computer, or take other steps to back them up.
z z
), press the
[ ][ ] buttons to choose [Low Level
Format], and then press the [ ][ ] buttons to select this option. A [ ] icon is displayed.
z z
) to continue with the formatting process.
•
Low-level formatting takes longer than “Formatting Memory Cards” ( = 101 ),
because data is erased from all storage regions of the memory card.
• You can cancel low-level formatting in progress by choosing [Stop]. In this case, all data will be erased, but the memory card can be used normally.
File Numbering
Your shots are automatically numbered in sequential order (0001 – 9999) and saved in folders that store up to 2,000 images each. You can change how the camera assigns file numbers.
Continuous
Auto Reset z z choose an option.
Images are numbered consecutively (until the 9999th shot is taken/ saved) even if you switch memory cards.
Image numbering is reset to 0001 if you switch memory cards, or when a new folder is created.
• Regardless of the option selected in this setting, shots may be numbered consecutively after the last number of existing images on newly inserted memory cards. To start saving shots from 0001, use an empty (or formatted,
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
102
Date-Based Image Storage
Instead of saving images in folders created each month, you can have the camera create folders each day you shoot to store shots taken that day.
z z
[Daily].
z z created on the shooting date.
Metric / Non-Metric Display
Change the unit of measurement shown in GPS elevation information
(
), the zoom bar (
), and elsewhere from m/cm to ft/in as needed.
z z
Checking Certification Logos
Some logos for certification requirements met by the camera can be viewed on the screen. Other certification logos are printed in this guide, on the camera packaging, or on the camera body.
z z then press the [ ] button.
Display Language
Change the display language as needed.
z z the [ ] button.
z z a language, and then press the [ ] button.
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
• You can also access the [Language] screen in Playback mode by pressing and holding the [ ] button and immediately pressing the [ ] button.
103
Adjusting Other Settings
The following settings can also be adjusted on the [ ] tab.
• [Video System] (
• [Wireless settings] (
)
Restoring Default Camera Settings
If you accidentally change a setting, you can restore default camera settings.
1
Access the [Reset All] screen.
z z
[ ] button.
2
Restore default settings.
z z z and then press the [ ] button.
Default settings are now restored.
• The following functions are not restored to default settings.
-
[ ] tab settings [Date/Time] ( = 99 ), [Time Zone] ( = 99
), [Language
), and [Video System] ( = 109 )
-
Custom white balance data you have recorded ( = 47
)
- Shooting mode (
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
104
Accessories
Enjoy the camera in more ways with optional Canon accessories and other compatible accessories sold separately
System Map ....................................................
Optional Accessories.....................................
Power Supplies ...................................................
Flash Unit ............................................................
Other Accessories ...............................................
Printers ................................................................
Photo and Movie Storage ....................................
Using Optional Accessories..........................
Playback on a TV ................................................
Using the Software .........................................
Checking Your Computer Environment ...............
Installing the Software .........................................
Saving Images to a Computer .............................
Printing Images ..............................................
Easy Print ............................................................
Configuring Print Settings ...................................
Printing Movie Scenes ........................................
Adding Images to the Print List (DPOF) ..............
Adding Images to a Photobook ...........................
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
105
System Map
Included Accessories
Wrist Strap Battery Pack
NB-11L
Battery Charger
CB-2LF/CB-2LFE* 1
USB Cable (camera end: Mini-B)* 2
Memory Card Card Reader
Cables
Computer
Connect Station
CS100* 3
AV Cable AVC-DC400
Flash Unit
TV/Video
System
PictBridge-Compatible Printers
High-Power Flash
HF-DC2
*1 Also available for purchase separately.
*2 A genuine Canon accessory is also available (Interface Cable IFC-400PCU).
*3 Use the latest firmware.
Use of genuine Canon accessories is recommended.
This product is designed to achieve excellent performance when used with genuine
Canon accessories.
Canon shall not be liable for any damage to this product and/or accidents such as fire, etc., caused by the malfunction of non-genuine Canon accessories (e.g., a leakage and/or explosion of a battery pack). Please note that any repairs your Canon product may require as a result of such malfunction are not covered under warranty and will incur a fee.
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
106
Optional Accessories
The following camera accessories are sold separately. Note that availability varies by area, and some accessories may no longer be available.
Power Supplies
Battery Pack NB-11LH
z z
Battery Charger CB-2LF/CB-2LFE
z z
NB-11L.
• The battery pack includes a convenient cover which you can attach to know the charge status at a glance. Attach the cover so that is visible on a charged battery pack, and attach it so that is not visible on an uncharged battery pack.
• Battery Pack NB-11L is also supported.
• Battery Charger CB-2LD is also supported.
• The battery charger can be used in areas with 100 – 240 V AC power (50/60 Hz).
• For power outlets in a different format, use a commercially available adapter for the plug. Never use an electrical transformer designed for traveling, which may damage the battery pack.
Flash Unit
Other Accessories
Printers
High-Power Flash HF-DC2
z z that are out of range of the built-in flash.
Interface Cable IFC-400PCU
z z or printer.
AV Cable AVC-DC400
z z playback on the larger TV screen.
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
Canon-Brand
PictBridge-Compatible Printers
z z print images by connecting the camera directly to a printer.
For details, visit your nearest Canon retailer.
107
Photo and Movie Storage
Connect Station CS100
z z viewing on a connected TV, printing wirelessly on a Wi-Fi-compatible printer, sharing over the Internet, and more.
Still Images
Using Optional Accessories
Movies
Still Images Movies
Playback on a TV
Connecting the camera to a TV with the AV Cable AVC-DC400 (sold separately) enables you to view your shots on the larger screen of the TV as you control the camera.
For details on connection or how to switch inputs, refer to the TV manual.
• Some information may not be displayed when viewing images on a TV
(
).
Yellow
Yellow
Black or white
Black
1
Make sure the camera and TV are off.
2
Connect the camera to the TV.
z z the video inputs as shown.
z z and insert the cable plug fully into the camera terminal.
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
108
3
Turn the TV on and switch to video input.
z z you connected the cable to in step 2.
4
Turn the camera on.
z z on.
z z displayed on the TV. (Nothing is displayed on the camera screen.) z z
TV before disconnecting the cable.
• Correct display is not possible unless the camera video output format (NTSC or PAL) matches the TV format. To change the video output format, press the [ ] button and choose [Video System] on the [ ] tab. (For Japan, choose [NTSC].)
Using the Software
To utilize the features of the following software, download the software from the Canon website and install it on your computer.
• CameraWindow
- Import images to your computer
• Image Transfer Utility
- Set up Image Sync (
) and receive images
• Map Utility
- Use a map to view GPS information that has been added to images
• To view and edit images on a computer, use preinstalled or commonly available software compatible with images captured by the camera.
Checking Your Computer Environment
For detailed software system requirements and compatibility information
(including support in new operating systems), visit the Canon website.
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
109
Installing the Software
Windows 7 and Mac OS X 10.8 are used here for the sake of illustration.
1
Download the software.
z z
Internet, access http://www.canon.com/ icpd/.
z z z z
2
Install the files.
z z on-screen instructions to complete the installation process. Installation may take some time, depending on computer performance and the Internet connection.
z z after installation.
• Internet access is required, and any ISP account charges and access fees must be paid separately.
• To uninstall the software, follow these steps.
- Windows: Select [Start] menu ► [All Programs] ► [Canon Utilities], and then choose the software for uninstallation.
- Mac OS: In the [Canon Utilities] folder within the [Applications] folder, drag the folder of the software for uninstallation to the Trash, and then empty the
Trash.
Saving Images to a Computer
Using a USB cable (sold separately; camera end: Mini-B), you can connect the camera to the computer and save images to the computer.
1
Connect the camera to the computer.
z z cover ( ). With the smaller plug of the
USB cable in the orientation shown, insert the plug fully into the camera terminal ( ).
z z in the computer’s USB port. For details about USB connections on the computer, refer to the computer user manual.
2
Turn the camera on to access
CameraWindow.
z z on.
z z when a connection is established between the camera and computer.
z z below.
z z change program link of [ ].
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
110
z z
Camera] and then click [OK].
z z ].
3
Save the images to the computer.
z z then click [Import Untransferred Images].
z z folder on the computer, in separate folders named by date.
z z
CameraWindow, press the [ ] button to turn the camera off, and unplug the cable.
z z use preinstalled or commonly available software compatible with images captured by the camera.
• Windows 7: If the screen in step 2 is not displayed, click the [ ] icon in the taskbar.
• Mac OS: If CameraWindow is not displayed after step 2, click the
[CameraWindow] icon in the Dock.
• Although you can save images to a computer simply by connecting your camera to the computer without using the software, the following limitations apply.
- It may take a few minutes after you connect the camera to the computer until camera images are accessible.
- Images shot in vertical orientation may be saved in horizontal orientation.
- Image protection settings may be cleared from images saved to a computer.
- Some problems may occur when saving images or image information, depending on the operating system version, the software in use, or image file sizes.
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
111
Still Images Movies
Printing Images
Your shots can easily be printed by connecting the camera to a printer. On the camera, you can specify images to set up batch printing, prepare orders for photo development services, and prepare orders or print images for photobooks.
A Canon SELPHY CP series compact photo printer is used here for the sake of illustration. Screens displayed and available functions vary by printer. Also refer to the printer manual for additional information.
Still Images
Easy Print
Easily print your shots by connecting the camera to a PictBridge-compatible printer (sold separately) with the USB cable.
1
Make sure the camera and printer are off.
2
Connect the camera to the printer.
z z smaller cable plug in the orientation shown, insert the plug fully into the camera terminal.
z z printer. For other connection details, refer to the printer manual.
3
Turn the printer on.
4
Turn the camera on.
z z on.
5
Choose an image.
z z image.
6
Access the printing screen.
z z press the [ ] button again.
7
Print the image.
z z z
[Print], and then press the [ ] button.
Printing now begins.
z z procedures starting from step 5 after printing is finished.
z z camera and printer off and disconnect the cable.
• For Canon-brand PictBridge-compatible printers (sold separately), see
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
112
Still Images
Configuring Print Settings
Cropping
Paper
Settings
1
Access the printing screen.
z z
(
= 112 ) to access the screen at left.
2
Configure the settings.
z z item, and then press the [ ][ ] buttons to choose an option.
Default
Date
File No.
Both
Off
Default
Off
Matches current printer settings.
Prints images with the date added.
Prints images with the file number added.
Prints images with both the date and file number added.
–
Matches current printer settings.
–
On
Uses information from the time of shooting to print under optimal settings.
Red-Eye1 Corrects red-eye.
No. of Copies Choose the number of copies to print.
– Specify a desired image area to print (
).
– Specify the paper size, layout, and other details (
Still Images
Cropping Images before Printing
By cropping images before printing, you can print a desired image area instead of the entire image.
1
Choose [Cropping].
z z
Settings” (
= 113 ) to access the printing
screen, choose [Cropping] and press the
[ ] button.
z z indicating the image area to print.
2
Adjust the cropping frame as needed.
z z z lever.
z
[ ][ ][ ][ ] buttons.
z z z z ] button, press the
[ ][ ] buttons to choose [OK], and then press the [ ] button.
3
Print the image.
z z
) to print.
• Cropping may not be possible at small image sizes, or at some aspect ratios.
• Dates may not be printed correctly if you crop images shot with
[Date Stamp ] selected.
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
113
Still Images
Choosing Paper Size and Layout before Printing
1
Choose [Paper Settings].
z z
) to access the printing screen, choose [Paper Settings] and press the [ ] button.
2
Choose a paper size.
z z option, and then press the [ ] button.
3
Choose a type of paper.
z z option, and then press the [ ] button.
4
Choose a layout.
z z z option.
z buttons to specify the number of images per sheet.
z z
5
Print the image.
Available Layout Options
Default Matches current printer settings.
Bordered
Borderless
N-up
ID Photo
Fixed Size
Prints with blank space around the image.
Borderless, edge-to-edge printing.
Choose how many images to print per sheet.
Prints images for identification purposes.
Only available for images with a recording pixel setting of L.
Choose the print size.
Choose from 3.5 x 5 in., postcard, or wide-format prints.
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
114
Still Images
Printing ID Photos
1
Choose [ID Photo].
z z
Paper Size and Layout before Printing”
(
= 114 ), choose [ID Photo] and press
the [ ] button.
2
Choose the long and short side length.
z z item. Choose the length by pressing the
[ ][ ] buttons, and then press the [ ] button.
3
Choose the printing area.
z z
Printing” (
= 113 ) to choose the printing
area.
4
Print the image.
Movies
Printing Movie Scenes
1
Access the printing screen.
z z
) to choose a movie. The screen at left is displayed.
2
Choose a printing method.
z z and then press the [ ][ ] buttons to choose the printing method.
3
Print the image.
Movie Printing Options
Single Prints the current scene as a still image.
Sequence
Prints a series of scenes, a certain interval apart, on a single sheet of paper. You can also print the folder number, file number, and elapsed time for the frame by setting [Caption] to [On].
• To cancel printing in progress, press the [ ] button, choose [OK], and then press the [ ] button again.
• After displaying a scene to print as described in steps 2 – 5 of “Viewing”
(
= 56 ), you can also access the screen in step 1 here by pressing the
[ ][ ] buttons to choose [ ] in the movie control panel and then pressing the
[ ] button.
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
115
Adding Images to the Print List (DPOF)
Still Images
) and ordering prints from a photo development service can be set up on the camera. Choose up to 998 images on a memory card and configure relevant settings, such as the number of copies, as follows. The printing information you prepare this way will conform to
DPOF (Digital Print Order Format) standards.
Still Images
Configuring Print Settings
Specify the printing format, whether to add the date or file number, and other settings as follows. These settings apply to all images in the print list.
z z ] button, and then choose [Print Settings] on the [ ] tab.
Choose and configure items as desired
(
).
Print Type
Date
File No.
Clear DPOF data
Standard
Index
Both
On
Off
On
Off
On
Off
One image is printed per sheet.
Smaller versions of multiple images are printed per sheet.
Both standard and index formats are printed.
Images are printed with the shooting date.
–
Images are printed with the file number.
–
All image print list settings are cleared after printing.
–
• Not all of your DPOF settings may be applied in printing by the printer or photo development service, in some cases.
• [ ] may be displayed on the camera to warn you that the memory card has print settings that were configured on another camera.
Changing the print settings using this camera may overwrite all previous settings.
• Setting [Date] to [On] may cause some printers to print the date twice.
• Specifying [Index] will prevent you from choosing [On] for both [Date] and [File
No.] at the same time.
• Index printing is not available on some Canon-brand PictBridge-compatible printers (sold separately).
• The date is printed in a format matching setting details in [Date/Time] on the
).
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
116
Still Images
Setting Up Printing for Individual Images
1
Choose [Select Images & Qty.].
z z ] button, choose
[Select Images & Qty.] on the [ ] tab, and then press the [ ] button.
2
Choose an image.
z z image, and then press the [ ] button.
z z copies.
z z image, it is labeled with a [ ] icon. To cancel index printing for the image, press the [ ] button again. [ ] is no longer displayed.
3
Specify the number of prints.
z z number of prints (up to 99).
z z specify the number of prints, repeat steps
2 – 3.
z z z index prints. You can only choose which images to print, by following step 2.
z to return to the menu screen.
] button
Still Images
Setting Up Printing for a Range of Images
z z for Individual Images” (
[Select Range] and press the [ ] button.
z z
z z
[Order], and then press the [ ] button.
Still Images
Setting Up Printing for All Images
z z for Individual Images” (
[Select All Images] and press the [ ] button.
z z and then press the [ ] button.
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
Still Images
Clearing All Images from the Print List
z z for Individual Images” (
[Clear All Selections] and press the [ ] button.
z z and then press the [ ] button.
117
Still Images
Printing Images Added to the Print List (DPOF)
z z
), the screen at left is displayed after you connect the camera to a PictBridge-compatible printer.
Press the [ ][ ] buttons to choose [Print now], and then simply press the [ ] button to print the images in the print list.
z z stop will be resumed from the next image.
Still Images
Adding Images to a Photobook
Photobooks can be set up on the camera by choosing up to 998 images on a memory card and importing them into the software on your computer, where they are stored in their own folder. This is convenient when ordering printed photobooks online or printing photobooks with your own printer.
Choosing a Selection Method
z z ] button, choose
[Photobook Set-up] on the [ ] tab, and then choose how you will select images.
• [ ] may be displayed on the camera to warn you that the memory card has print settings that were configured on another camera.
Changing the print settings using this camera may overwrite all previous settings.
Still Images
Adding Images Individually
1
Choose [Select].
z z
a Selection Method” ( = 118 ), choose
[Select] and press the [ ] button.
2
Choose an image.
z z image, and then press the [ ] button.
z z z z press the [ ] button again. [ ] is no longer displayed.
z z images.
z z to return to the menu screen.
] button
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
118
Still Images
Adding All Images to a Photobook
z z
a Selection Method” ( = 118 ), choose
[Select All Images] and press the [ ] button.
z z and then press the [ ] button.
Still Images
Removing All Images from a Photobook
z z
a Selection Method” ( = 118 ), choose
[Clear All Selections] and press the [ ] button.
z z and then press the [ ] button.
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
119
Appendix
Helpful information when using the camera
Troubleshooting .............................................
On-Screen Messages .....................................
On-Screen Information ..................................
Shooting (Information Display) ............................
Playback (Detailed Information Display) .............
Functions and Menu Tables ..........................
Functions Available in Each Shooting Mode .......
FUNC. Menu .......................................................
Shooting Tab .................................................
Set Up Tab .....................................................
Playback Tab .................................................
Print Tab ........................................................
Playback Mode FUNC. Menu ..............................
Handling Precautions ....................................
Specifications .................................................
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
120
Troubleshooting
If you think there is a problem with the camera, first check the following.
If the items below do not solve your problem, contact a Canon Customer
Support Help Desk.
Power
Nothing happens when the power button is pressed.
•
Confirm that the battery pack is charged ( = 10
).
•
Confirm that the battery pack is inserted facing the correct way ( = 11
).
• Confirm that the memory card/battery cover is fully closed (
).
• Dirty battery terminals reduce battery performance. Try cleaning the terminals with a cotton swab and reinserting the battery pack a few times.
The battery pack runs out of power quickly.
• Battery performance decreases at low temperatures. Try warming the battery pack a little by putting it in your pocket, for example, ensuring that the terminals do not touch any metal objects.
• If these measures do not help and the battery pack still runs out of power soon after charging, it has reached the end of its life. Purchase a new battery pack.
The lens is not retracted.
• Do not open the memory card/battery cover while the camera is on. Close the cover,
turn the camera on, and then turn it off again ( = 11 ).
The battery pack is swollen.
• Battery swelling is normal and does not pose any safety concerns. However, if battery swelling prevents the battery pack from fitting in the camera, contact a Canon
Customer Support Help Desk.
Display on a TV
Camera images look distorted or are not displayed on a TV ( = 109 ).
Shooting
Cannot shoot.
•
), press the shutter button halfway (
Strange display on the screen under low light ( = 19 ).
Strange display on the screen when shooting.
Note that the following display problems are not recorded in still images but are recorded in movies.
• The screen may darken under bright light.
• The screen may flicker under fluorescent or LED lighting.
• Purplish banding may appear on the screen if you compose a shot that includes a bright light source.
No date stamp is added to images.
•
Configure the [Date Stamp ] setting ( = 12 ). Note that date stamps are not
added to images automatically, merely because you have configured the [Date/Time]
•
Date stamps are not added in shooting modes ( = 133
) in which [Date Stamp ] cannot be configured (
[ ] flashes on the screen when the shutter button is pressed, and
shooting is not possible ( = 26
).
[ ] is displayed when the shutter button is pressed halfway ( = 26 ).
• Set the flash mode to [ ] (
•
).
• Mount the camera on a tripod or take other measures to keep it still.
•
Set [IS Mode] to [Continuous] ( = 54 ). However, you should set [IS Mode] to [Off]
when using a tripod or other means to secure the camera (
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
121
Shots are out of focus.
• Press the shutter button halfway to focus on subjects before pressing it all the way down to shoot (
•
Make sure subjects are within focusing range ( = 137 ).
•
Set [Lamp Setting] to [On] ( = 35
).
• Confirm that unneeded functions such as macro are deactivated.
• Try shooting with focus lock (
No AF frames are displayed and the camera does not focus when the shutter button is pressed halfway.
• To have AF frames displayed and the camera focus correctly, try composing the shot with higher-contrast subject areas centered before you press the shutter button halfway. Otherwise, try pressing the shutter button halfway repeatedly.
Subjects in shots look too dark.
•
Set the flash mode to [ ] ( = 51
).
•
Adjust brightness by using exposure compensation ( = 44
).
• Adjust contrast by using i-Contrast (
•
).
Subjects look too bright, highlights are washed-out.
• Set the flash mode to [ ] (
•
Adjust brightness by using exposure compensation ( = 44
).
•
).
• Reduce the lighting on subjects.
Shots look too dark despite the flash firing (
).
•
Shoot within flash range ( = 135 ).
• Increase the ISO speed (
Subjects in flash shots look too bright, highlights are washed-out.
•
Shoot within flash range ( = 135 ).
• Set the flash mode to [ ] (
White spots appear in flash shots.
• This is caused by light from the flash reflecting off dust or airborne particles.
Shots look grainy.
•
).
• High ISO speeds in some shooting modes may cause grainy images (
Subjects are affected by red-eye.
• Set [Lamp Setting] to [On] (
= 35 ) to light the red-eye reduction lamp (
flash shots. Note that while the red-eye reduction lamp is lit (for about one second), it is not possible to shoot, because the lamp is counteracting red-eye. For best results, have subjects look at the red-eye reduction lamp. Also try increasing the lighting in indoor scenes and shooting at closer range.
• Edit images using red-eye correction (
Recording to the memory card takes too long, or continuous shooting is slower.
•
Use the camera to perform low-level formatting of the memory card ( = 102
).
Shooting settings or FUNC. menu settings are not available.
• Available setting items vary by shooting mode. Refer to “Functions Available in Each
Shooting Mode”, “FUNC. Menu”, and “Shooting Tab” (
).
Shooting Movies
The elapsed time shown is incorrect, or recording is interrupted.
• Use the camera to format the memory card, or switch to a card that supports highspeed recording. Note that even if the elapsed time display is incorrect, the length
of movies on the memory card corresponds to the actual recording time ( = 101 ,
[ ] is displayed and shooting stops automatically.
The camera’s internal memory buffer filled up as the camera could not record to the memory card quickly enough. Try one of the following measures.
•
Use the camera to perform low-level formatting of the memory card ( = 102
).
• Lower the image quality (
•
Switch to a memory card that supports high-speed recording ( = 137 ).
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
122
Playback
Playback is not possible.
• Image or movie playback may not be possible if a computer is used to rename files or alter the folder structure.
Playback stops, or audio skips.
• Switch to a memory card that you have performed low-level formatting on with the camera (
).
• There may be brief interruptions when playing movies copied to memory cards that have slow read speeds.
• When movies are played on a computer, frames may be dropped and audio may skip if computer performance is inadequate.
Sound is not played during movies.
• Adjust the volume (
= 56 ) if you have activated [Mute] (
) or the sound in the movie is faint.
Memory Card
The memory card is not recognized.
• Restart the camera, with the memory card in it (
Computer
Cannot transfer images to a computer.
When attempting to transfer images to the computer via a cable, try reducing the transfer speed as follows.
• Press the [ ] button to enter Playback mode. Hold the [ ] button down as you press the [ ] and [ ] buttons at the same time. On the next screen, press the
[ ][ ] buttons to choose [B], and then press the [ ] button.
Wi-Fi
Cannot access the Wi-Fi menu by pressing the [ ] button.
• The Wi-Fi menu cannot be accessed while the camera is connected to a printer or computer via a cable. Disconnect the cable.
Cannot add a device/destination.
• A total of 20 items of connection information can be added to the camera. Erase unneeded connection information from the camera first, and then add new devices/ destinations (
•
Use a computer or smartphone to register Web services ( = 82
).
• To add a smartphone, first install the dedicated application Camera Connect on your
).
• To add a computer, first install the software CameraWindow on your computer. Also
check your computer and Wi-Fi environment and settings ( = 76
,
).
• Do not use the camera near sources of Wi-Fi signal interference, such as microwave ovens, Bluetooth devices, or other equipment operating on the 2.4 GHz band.
• Bring the camera closer to the other device you are trying to connect to (such as the access point), and make sure there are no objects between the devices.
Cannot connect to the access point.
• Confirm that the access point channel is set to a channel supported by the camera
(
). Note that instead of auto channel assignment, it is advisable to specify a supported channel manually.
Cannot send images.
• The destination device has insufficient storage space. Increase the storage space on the destination device and resend the images.
• The write-protect switch of the memory card in the destination camera is set to the locked position. Slide the write-protect switch to the unlocked position.
• Images cannot be sent to CANON iMAGE GATEWAY or other Web services if you move or rename image files or folders on the computer that received images sent using Image Sync via an access point (
= 91 ). Before moving or renaming these
image files or folders on the computer, make sure the images have already been sent to CANON iMAGE GATEWAY or other Web services.
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
123
Cannot resize images for sending.
• Images cannot be resized to be bigger than the recording pixel setting of their original size.
• Movies cannot be resized.
Images take a long time to send./The wireless connection is disrupted.
• Multiple images may take a long time to send. Try resizing the image to reduce sending time (
).
• Movies may take a long time to send.
• Do not use the camera near sources of Wi-Fi signal interference, such as microwave ovens, Bluetooth devices, or other equipment operating on the 2.4 GHz band. Note that images may take a long time to send even when [ ] is displayed.
• Bring the camera closer to the other device you are trying to connect to (such as the access point), and make sure there are no objects between the devices.
No notification message is received on a computer or smartphone after adding CANON iMAGE GATEWAY to the camera.
• Make sure the email address you entered is correct, and try adding the destination again.
• Check the email settings on the computer or smartphone. If they are configured to block email from certain domains, you may not be able to receive the notification message.
Want to erase Wi-Fi connection information before disposing of the camera or giving it to someone else.
• Reset the Wi-Fi settings (
On-Screen Messages
If an error message is displayed, respond as follows.
Shooting or Playback
No memory card
• The memory card may be inserted facing the wrong way. Reinsert the memory card
facing the correct way ( = 11 ).
Memory card locked
• The write-protect switch of the memory card is set to the locked position. Switch the
write-protect switch to the unlocked position ( = 11
).
Cannot record!
• Shooting was attempted without a memory card in the camera. To shoot, insert a
memory card facing the correct way ( = 11
).
)
• If the same error message is displayed even after you have formatted a supported memory card (
) and have inserted it facing the correct way (
a Canon Customer Support Help Desk.
Insufficient space on card
•
There is not enough free space on the memory card to shoot ( = 23
,
or edit images (
68 ). Either erase unneeded images (
memory card with enough free space ( = 11
).
)
No Image.
• The memory card does not contain any images that can be displayed.
Protected! (
)
Unidentified Image/Incompatible JPEG/Image too large./Cannot play back MOV/Cannot play back MP4
• Unsupported or corrupt images cannot be displayed.
• It may not be possible to display images that were edited or renamed on a computer, or images shot with another camera.
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
124
Cannot magnify!/Cannot rotate/Cannot modify image/Cannot modify/
Unselectable image.
• The following functions may be unavailable for images that were renamed or already edited on a computer, or images shot with another camera. Note that starred (*) functions are not available for movies.
), Print List* (
Photobook Set-up* (
Exceeded selection limit
• More than 998 images were selected for Print List (
) or Photobook Set-up
(
). Choose 998 images or less.
•
Print List ( = 116 ) or Photobook Set-up (
= 118 ) settings could not be saved
correctly. Reduce the number of selected images and try again.
• You attempted to choose more than 500 images in Protect (
),
Favorites ( = 66 ), Print List (
), or Photobook Set-up (
).
Naming error!
• The folder could not be created or images could not be recorded, because the highest supported folder number (999) for storing images on the card has been reached and the highest supported image number (9999) for images in folders has been reached.
On the [ ] tab, change [File Numbering] to [Auto Reset] (
), or format the
).
Lens Error
• This error may occur if the lens is held while it is moving, or when the camera is used in dusty or sandy locations.
• Frequent display of this error message may indicate camera damage. In this case, contact a Canon Customer Support Help Desk.
A camera error was detected (error number)
• If this error message is displayed immediately after a shot, the image may not have been saved. Switch to Playback mode to check for the image.
• Frequent display of this error message may indicate camera damage. In this case, write down the error number (Exx) and contact a Canon Customer Support Help
Desk.
File Error
•
Correct printing ( = 112 ) may not be possible for photos from other cameras or
images that have been altered using computer software, even if the camera is connected to the printer.
Print error
• Check the paper size setting (
). If this error message is displayed when the setting is correct, restart the printer and complete the setting on the camera again.
Ink absorber full
• Contact a Canon Customer Support Help Desk to request assistance with ink absorber replacement.
Wi-Fi
Connection failed
• No access points were recognized. Check the access point settings (
• A device could not be found. Turn the camera off and on again, and retry the connection.
• Check the device you want to connect to and make sure it is ready for connection.
Cannot determine access point
• The WPS buttons on numerous access points were pressed simultaneously. Try reconnecting again.
No access points found
• Check to make sure that the access point is turned on.
• When connecting to an access point manually, make sure that you entered the correct SSID.
Incorrect password/Incorrect Wi-Fi security settings
•
Check the access point security settings ( = 78 ).
IP address conflict
• Reset the IP address so that it does not conflict with another.
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
125
Disconnected/Receiving failed/Sending failed
• You may be in an environment where Wi-Fi signals are obstructed.
• Avoid using the camera’s Wi-Fi function around microwave ovens, Bluetooth devices, and other devices that operate on the 2.4 GHz band.
• Bring the camera closer to the other device you are trying to connect to (such as the access point), and make sure there are no objects between the devices.
• Check the connected device to make sure it is not experiencing errors.
Sending failed
Memory card error
• If the same error message is displayed even when you have inserted a formatted memory card facing the correct way, contact a Canon Customer Support Help Desk.
Receiving failed
Insufficient space on card
• There is not enough free space on the memory card in the target camera to receive images. Erase images to create space on the memory card, or insert a memory card with sufficient space.
Receiving failed
Memory card locked
• The write-protect switch of the memory card in the camera to receive the images is set to the locked position. Slide the write-protect switch to the unlocked position.
Receiving failed
Naming error!
• When the highest folder number (999), and the highest image number (9999) have been reached on the receiving camera, images cannot be received.
Insufficient space on server
• Delete unnecessary images uploaded to CANON iMAGE GATEWAY to create space.
•
Save the images sent via Image Sync ( = 91
) to your computer.
Check network settings
• Check to make sure your computer can connect to the Internet with the current network settings.
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
126
On-Screen Information
Shooting (Information Display)
Battery level
)
White balance
Drive mode
)
Self-timer (
)
Camera shake warning (
Metering method
(
)
Recording pixel setting (
)
Recordable shots
(
)
Movie quality
(
)
Remaining time
(
)
Digital zoom magnification
(
)
Spot AE point frame
(
)
Focus range
(
,
)
IS mode icon
(
)
Shooting mode
(
icon (
)
Flash mode
(
,
)
Date stamp
(
)
i-Contrast (
)
Grid lines (
)
Shutter speed
Aperture value
Exposure compensation level
Image stabilization
Battery Level
An on-screen icon or message indicates the battery charge level.
Display Details
Sufficient charge
Slightly depleted, but sufficient
(Blinking red)
[Charge the battery]
Nearly depleted—charge the battery pack soon
Depleted—charge the battery pack immediately
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
127
Playback (Detailed Information Display)
Movies
Shooting mode
)
ISO speed
Exposure compensation level
White balance
Histogram (
)
Image editing
)
Recording pixel setting (
),
MP4 (movies)
Image Sync
(
)
Battery level
(
)
Metering method
(
)
Folder number - File number (
Current image no. /
Total no. of images
Shutter speed (still images), Image quality / Frame rate
(movies) (
)
Aperture value
Focus range
(
,
)
File size
Still images:
Recording pixel setting (
Movies: Playback
)
Red-eye correction
(
)
i-Contrast
(
,
)
Shooting date/time
(
• Some information may not be available when using a TV as the display
(
).
Summary of Movie Control Panel in “Viewing” (
)
Exit
Play
Slow Motion (Press the [ ][ ] buttons to adjust the playback speed. No sound is played.)
Skip Backward* (To continue skipping backward, keep holding down the [ ] button.)
Previous Frame (For fast-rewind, keep holding down the [ ] button.)
Next Frame (For fast-forward, keep holding down the [ ] button.)
Skip Forward* (To continue skipping forward, keep holding down the [ ] button.)
Shown when the camera is connected to a PictBridge-compatible printer
(
* Displays the frame approx. 4 sec. before or after the current frame.
• To skip forward or back during movie playback, press the [ ][ ] buttons.
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
128
Functions and Menu Tables
Functions Available in Each Shooting Mode
Shooting Mode
Function
Flash (
O
–
* 1
O
)
No Information Display
Information Display
*1 Not available, but switches to [ ] in some cases.
O
O
O
O
O
O
O
O
O
O
–
O
O
O
O
O
–
O
O
O
O
–
–
O
O
O
O
O
–
O
O
O
–
O
O
O
–
O
O
O
–
O
O
O
–
O
O
O
–
O
–
–
–
O
–
O
–
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O Available or set automatically. – Not available.
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
129
FUNC. Menu
Function
Light Metering (
)
White Balance (
)
Exposure Compensation (
)
)
)
Focus Range (
Drive Mode (
AUTO
100, 200, 400, 800, 1600
Delay*
1
Shots* 2
Shooting Mode
*1 Cannot be set to 0 seconds in modes without selection of the number of shots.
*2 One shot (cannot be modified) in modes without selection of the number of shots.
O
–
O
–
–
O
–
O
O
O
–
O
O
O
O
O
–
O
O
O
O
O
O
O
O
O
–
O
O
–
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
–
O
–
O
O
O
–
–
O
–
O
–
O
–
O
–
O
O
O
O
O
O
O
O
O
–
O
O
O
O
–
O
–
O
–
O
–
O
–
O
–
O
–
O
–
O
–
O
O
–
O
O
O
O
O
–
O
O
–
O
O
O
O
O
–
O
O
–
O
O
O
O
O
–
O
–
O
O
O
O
O
O
–
O
–
O
O
O
O
O
O
–
O
–
–
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
–
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
–
O Available or set automatically. – Not available.
–
O
–
O
O
O
O
O
O
O
–
O
O
–
O
O
O
O
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
130
Function
Recording pixels (
Movie Quality (
*1 Synchronizes with the recording pixel setting and is automatically set ( = 39
).
Shooting Mode
O
O
–
O
O
O
O
–
O
O
O
O
–
O
O
O
O
–
O
O
O
–
–
–
O
–
–
O
–
O
–
O
O
–
* 1
O
–
–
–
O
O
–
–
–
O
O
–
–
–
O
O
–
–
–
O
O
O
–
O
O
O Available or set automatically. – Not available.
O
O
–
O
O
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
131
Shooting Tab
Function
)
Face AiAF
Tracking AF
Center
,
On
Off
)
On
Off
Servo AF (
On
Off
Continuous AF (
On
Off
)
On
Off
Auto
Off
Review image after shooting (
Display Time Off/Quick/2 sec./4 sec./8 sec./Hold
Display Info
Off
Detailed
*1 [On] when subject movement is detected.
Shooting Mode
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
–
O
O
O
O
O
O
–
* 1
O
–
–
O
O
–
O
O
O
–
O
–
–
O
O
–
–
O
O
O
O
O
O
–
O
O
O
O
O
O
–
O
–
–
–
O
O
O
O
O
O
O
O
–
O
O
O
O
–
O
O
O
–
O
–
O
O
O
–
–
O
–
O
–
O
–
O
O
O
–
–
–
–
O
O
–
O
–
O
–
O
–
O
O
O
O
O
O
–
O
O
O
O
O
O
O
O
O
O
–
O
O
O
O
O
O
O
O
O
O
–
O
O
O
O
O
O
O
–
–
O
O
O
–
O
–
O
–
O
–
O
O
O
O
O
–
O
O
O
–
O
O
O
–
O
O
O
–
O
O
O
–
O
–
O
–
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O Available or set automatically. – Not available.
–
O
O
O
–
O
O
O
O
O
O
O
O
O
O
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
132
Function
)
On
Off
IS Settings (
IS Mode
Dynamic IS
Off
Date / Date & Time
Off/Continuous
Shoot Only
1
2
Shooting Mode
O
O
O
–
O
O
–
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
–
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
–
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
–
O
–
O
–
O
–
O
–
O
–
O
O
O
O
O Available or set automatically. – Not available.
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
133
Item
Mute
Volume
Hints & Tips
Date/Time
Time Zone
Lens Retraction
Eco Mode
Power Saving
Disp. Brightness
Start-up Image
Set Up Tab
Reference
Page
Item
Format
File Numbering
Create Folder
Units
Video System
Wireless settings
Certification Logo Display
Language
Reset All
Reference
Page
Playback Tab
Item
Slideshow
Erase
Protect
Rotate
Favorites
Photobook Set-up
Reference
Page
Item i-Contrast
Red-Eye Correction
Resize
Transition
Auto Rotate
Resume
Reference
Page
Print Tab
Item
Select Images & Qty.
Select Range
Reference
Page
–
Item
Select All Images
Clear All Selections
Print Settings
Playback Mode FUNC. Menu
Rotate
Protect
Favorites
Item
Reference
Page
Item
Play Movie
Image Search
Slideshow
Reference
Page
Reference
Page
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
134
Handling Precautions
• The camera is a high-precision electronic device. Avoid dropping it or subjecting it to strong impact.
• Never bring the camera near magnets, motors, or other devices that generate strong electromagnetic fields, which may cause malfunction or erase image data.
• If water droplets or dirt adheres to the camera or screen, wipe with a dry soft cloth, such as an eyeglass cloth. Do not rub hard or apply force.
• Never use cleaners containing organic solvents to clean the camera or screen.
• Use a blower brush to remove dust from the lens. If cleaning is difficult, contact a Canon Customer Support Help Desk.
• To prevent condensation from forming on the camera after sudden temperature changes (when the camera is transferred from cold to warm environments), put the camera in an airtight, resealable plastic bag and let it gradually adjust to the temperature before removing it from the bag.
• If condensation does form on the camera, stop using it immediately.
Continuing to use the camera in this state may damage it. Remove the battery pack and memory card, and wait until the moisture has evaporated before resuming use.
• Store unused battery packs in a plastic bag or other container. To maintain battery performance if you will not use the battery pack for some time, about once a year charge it and then use the camera until it runs out of power before storing the battery pack.
Specifications
Camera
Image Sensor
Camera Effective Pixels
(Image processing may cause a decrease in the number of pixels.) ..........Approx. 20 megapixels
Total Pixels ..........................................Approx. 20.5 megapixels
Image Size ..........................................1/2.3 type
Lens
Focal Length
(35mm film equivalent) ............................. 4.3 – 43.0 mm (24 – 240 mm)
Zoom Magnification .............................10×
Digital Zoom
Magnification .......................................Approx. 4×
Max. Magnification
(digital x optical zoom) .........................Approx. 40×
Focal Length
(max. telephoto, 35mm film equivalent) .......Equivalent to approx. 960 mm
Screen (Monitor)
Type .....................................................TFT color liquid crystal
Screen Size .........................................2.7 type
Effective Pixels ....................................Approx. 230,000 dots
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
135
Continuous Shooting (CIPA compliant)
Speed
(Varies depending on the subject, zoom position, and other shooting factors, as well as memory card brands.) ............... Normal Continuous Shooting in
Auto/P modes:
Approx. 0.8 shots/sec.
Normal Continuous Shooting Low
Light mode: Approx. 2.2 shots/sec.
Built-in Flash
Flash Range (Wide angle end) ............ 50 cm – 4.0 m (1.6 – 13 ft.)
Flash Range (Telephoto end) .............. 1.0 – 2.0 m (3.3 – 6.6 ft.)
Shutter Speed
Auto Mode (automatic settings) ...........1 – 1/2000 sec.
Range in all shooting modes
Max. .....................................................15 sec.
Min. ......................................................1/2000 sec.
Speed (unit: sec.) ................................ Long Shutter Mode
15, 13, 10, 8, 6, 5, 4, 3.2, 2.5, 2,
1.6, 1.3, 1
Aperture
F Number ............................................ 3.0 / 9.0 (W)
6.9 / 20 (T)
AF
AF Frame ............................................ Face Detect AiAF (number of AF frames: max. 9), Tracking AF,
Center
File Format .............................................. Design rule for Camera File system (DCF) compliant; DPOF
(version 1.1) compatible
Data Type (Still Images)
Image File Format ...............................Exif 2.3 (DCF 2.0)
Image Type .......................................... JPEG
Data Type (Movies)
Recording Format ................................MP4
Video ...................................................MPEG-4 AVC/H.264
Audio ...................................................MPEG-4 AAC-LC (Monaural)
Power Supply
Battery Pack ........................................NB-11L
Interface
Wired ................................................... Hi-Speed USB (Mini-B)
Analog Audio Output (Monaural)
Analog Video Output (NTSC/PAL)
Wireless ............................................... Wi-Fi
Specifications: IEEE 802.11b/g/n
Frequency: 2.4 GHz
Channels: 1 – 11
Security: WEP, WPA-PSK (AES/
TKIP), WPA2-PSK (AES/TKIP)
NFC
Operating Environment
Temperatures ......................................0 – 40 °C (32 – 104 °F)
Dimensions (CIPA compliant)
(WxHxD) .................................................. 95.3 x 56.8 x 23.6 mm
(3.75 x 2.24 x 0.93 in.)
Weight (CIPA compliant)
Including Battery Pack,
Memory Card .......................................Approx. 138 g (Approx. 4.87 oz.)
Camera Body Only ..............................Approx. 123 g (Approx. 4.34 oz.)
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
136
Number of Shots/Recording Time, Playback Time
Number of Shots (CIPA compliant) Approx. 190 shots
Number of Shots in Eco Mode Approx. 245 shots
Movie Recording Time
(CIPA compliant)* 1
Movie Recording Time
(Continuous Shooting)* 2
Playback Time* 3
Approx. 50 minutes
Approx. 1 hour, 30 minutes
Approx. 4 hours
*1 Total time when shooting repeatedly under the following conditions:
- In [ ] mode, with all other settings set to defaults
- With recording, stopping, zooming, and turning the camera on and off
*2 Total time when shooting repeatedly under the following conditions:
- In [ ] mode, with all other settings set to defaults
- Automatically stop/resume after the time or capacity per recording is reached
*3 Time when playing back a slideshow of still images.
Shooting Range
Shooting
Mode
Focus Range
–
Other modes
Maximum Wide Angle
( )
1 cm (0.4 in.) – infinity
5 cm (2.0 in.) – infinity
1 – 50 cm
(0.4 in. – 1.6 ft.)
3.0 m (9.8 ft.) – infinity
Maximum Telephoto
( )
1.0 m (3.3 ft.) – infinity
1.0 m (3.3 ft.) – infinity
–
3.0 m (9.8 ft.) – infinity
Number of Shots per Memory Card
Number of shots per 16 GB memory card (approx. shots)
3017
5925
16755
10798
80988
4015
• The values in the table are based on Canon measurement conditions and may change depending on the subject, memory card and camera settings.
Recording Time per Memory Card
Pixels
Recording Time per 16 GB
Memory Card (Approx.)
(1280 x 720) 2 hr. 35 min. 37 sec.
(640 x 480) 8 hr. 25 min. 48 sec.
Single Clip Recording Time
(Approx.)
29 min. 59 sec.
1 hr.
• The values in the table are based on Canon measurement conditions and may change depending on the subject, memory card and camera settings.
• Recording times for individual movies are based on memory cards rated at an SD speed class of 10. Recording may stop when cards rated at lower speed classes are used. Recording will also stop automatically when the file size reaches 4 GB, or when the card becomes full.
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
137
Battery Pack NB-11L
Type:
Nominal Voltage:
Nominal Capacity:
Charging Cycles:
Rechargeable lithium-ion battery
3.6 V DC
680 mAh
Approx. 300 times
Operating Temperatures: 0 – 40 °C (32 – 104 °F)
Battery Charger CB-2LF/CB-2LFE
Rated Input:
Rated Output:
100 – 240 V AC (50/60 Hz)
4.2 V DC, 0.41 A
Charging Time: Approx. 2 hours
Operating Temperatures: 5 – 40 °C (41 – 104 °F)
• Size, weight, and number of shots available are based on measurement guidelines of the Camera & Imaging Products Association (CIPA).
• Under some shooting conditions, the number of shots and recording time may be less than mentioned above.
• Number of shots/time with a fully charged battery pack.
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
138
Index
A
Accessories ....................................... 107
AE lock ................................................ 44
AF frames ............................................ 48
AUTO mode (shooting mode) ........ 14, 24
AV cable .................................... 107, 108
B
Batteries → Date/time (date/time battery)
Battery charger .............................. 2, 107
Battery pack
Charging ........................................ 10
Eco mode .................................... 100
Level ............................................ 127
Power saving ................................. 18
C
Camera
Reset all ...................................... 104
Camera access point mode ................. 76
Camera Connect ................................. 70
CameraWindow ................................... 76
CANON iMAGE GATEWAY ........... 70, 82
Center (AF frame mode)...................... 49
Color (white balance)........................... 46
Connecting via an access point ........... 78
Continuous shooting ............................ 33
Cropping .............................................113
Custom white balance ......................... 47
D
Date/time
Adding date stamps ...................... 32
Changing ....................................... 13
Date/time battery ........................... 13
Settings ......................................... 12
World clock .................................... 99
Defaults → Reset all
Digital zoom ................................... 28, 52
Display language ................................. 13
DPOF ..................................................116
Drive mode .......................................... 33
E
Eco mode .......................................... 100
Editing
i-Contrast ....................................... 67
Red-eye correction ........................ 68
Resizing images ............................ 67
Editing or erasing connection
information ........................................... 94
Erasing ................................................ 63
Error messages ................................. 124
Exposure
Compensation ............................... 44
Eye-Fi cards .......................................... 2
F
Face AiAF (AF frame mode) ................ 48
Face self-timer (shooting mode) .......... 41
Favorites .............................................. 66
File numbering ................................... 102
Fireworks (shooting mode) .................. 37
Fish-eye effect (shooting mode) .......... 38
Flash
Deactivating flash .................... 32, 52
On ................................................. 51
Slow synchro ................................. 51
Focusing
AF frames ...................................... 48
AF-point zoom ............................... 50
Servo AF ....................................... 49
Focus lock ........................................... 49
Focus range
Infinity ............................................ 48
Macro ............................................ 47
FUNC. menu
Basic operations ............................ 20
Table .................................... 130, 134
G
Grid lines ............................................. 52
I
i-Contrast ....................................... 46, 67
Images
Display period ............................... 53
Erasing .......................................... 63
Playback → Viewing
Protecting ...................................... 60
Image stabilization ............................... 54
Image Sync.......................................... 91
Indicator ............................................... 22
Infinity (focus range) ............................ 48
ISO speed............................................ 45
L
Lamp.................................................... 35
Long shutter (shooting mode).............. 42
Low light (shooting mode) ................... 37
M
Macro (focus range) ............................ 47
Magnified display ................................. 59
Memory cards ........................................ 2
Recording time ............................ 137
Menu
Basic operations ............................ 21
Table ............................................ 129
Metering method.................................. 45
Miniature effect (shooting mode) ......... 39
Monochrome (shooting mode)............. 40
Movies
Recording time ............................ 137
P
P (shooting mode) ............................... 44
Package contents .................................. 2
Photobook set-up ...............................118
PictBridge ...................................107, 112
Playback → Viewing
Portrait (shooting mode) ...................... 37
Poster effect (shooting mode) ............. 38
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
139
Power ................................................ 107
→ Battery pack
→ Battery charger
Power saving ....................................... 18
Printing ...............................................112
Program AE ......................................... 44
Protecting ............................................ 60
R
Recording pixels (image size) ............. 34
Red-eye correction .............................. 68
Remote shooting ................................. 93
Reset all............................................. 104
Resizing images .................................. 67
Rotating ............................................... 65
S
Saving images to a computer .......76, 110
Screen
Display language ........................... 13
Icons .................................... 127, 128
Menu → FUNC. menu, Menu
SD/SDHC/SDXC memory cards
→ Memory cards
Searching ............................................ 58
Self-timer ............................................. 30
2-second self-timer ........................ 31
Sending images ................................... 89
Sending images to a computer ............ 76
Sending images to another camera..... 87
Sending images to a printer................. 86
Sending images to a smartphone ........ 70
Sending images to Web services ........ 82
Servo AF .............................................. 49
Shooting
Shooting date/time → Date/time
Shooting information ................... 127
Slideshow ............................................ 59
Software
Installation ..............................76, 110
Saving images to
a computer .............................76, 110
Sounds ................................................ 98
Strap ................................................ 2, 10
Super vivid (shooting mode) ................ 38
T
Terminal ......................................108, 112
Toy camera effect (shooting mode) ..... 40
Tracking AF ......................................... 49
Traveling with the camera ................... 99
Troubleshooting ................................. 121
TV display .......................................... 108
V
Viewing .......................................... 15, 56
Image search ................................ 58
Index display ................................. 57
Magnified display .......................... 59
Single-image display ............... 15, 56
Slideshow ...................................... 59
TV display ................................... 108
W
White balance (color)........................... 46
Widescreen (recording pixel setting) ... 34
Wi-Fi functions ..................................... 69
Wi-Fi menu .......................................... 73
World clock .......................................... 99
Wrist strap → Strap
Z
Zoom ....................................... 14, 24, 28
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
140
Wi-Fi (Wireless LAN) Precautions
• Countries and Regions Permitting WLAN Use
Use of WLAN is restricted in some countries and regions, and illegal use may be punishable under national or local regulations. To avoid violating WLAN regulations, visit the Canon website to check where use is allowed.
Note that Canon cannot be held liable for any problems arising from
WLAN use in other countries and regions.
• Doing any of the following may incur legal penalties:
Altering or modifying the product
Removing the certification labels from the product
• According to foreign exchange and foreign trade law regulations, export permission (or service transaction permission) from the Japanese government is necessary to export strategic resources or services
(including this product) outside Japan.
• Because this product includes American encryption software, it falls under U.S. Export Administration Regulations, and cannot be exported to or brought into a country under U.S. trade embargo.
• Be sure to make notes of the wireless LAN settings you use.
The wireless LAN settings saved to this product may change or be erased due to incorrect operation of the product, the effects of radio waves or static electricity, or accident or malfunction. Be sure to make notes of wireless LAN settings as a precaution. Please note that Canon accepts no responsibility for direct or indirect damages or loss of earnings resulting from a degradation or disappearance of content.
• When transferring this product to another person, disposing of it, or sending it for repair, be sure to note the wireless LAN settings and reset the product to its default settings (erase settings) if necessary.
• Canon will not make compensation for damages resulting from loss or theft of the product.
Canon accepts no responsibility for damages or loss resulting from unauthorized access or use of target devices registered on this product due to loss or theft of the product.
• Be sure to use the product as directed in this guide.
Be sure to use the wireless LAN function of this product within the guidelines noted in this guide. Canon accepts no responsibility for damages or loss if the function and product are used in ways other than as described in this guide.
• Do not use the wireless LAN function of this product near medical equipment or other electronic equipment.
Use of the wireless LAN function near medical equipment or other electronic equipment may affect operation of those devices.
Radio Wave Interference Precautions
• This product may receive interference from other devices that emit radio waves. To avoid interference, be sure to use this product as far away as possible from such devices, or avoid using the devices at the same time as this product.
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
141
Security Precautions
Because Wi-Fi uses radio waves to transmit signals, security precautions more stringent than when using a LAN cable are required.
Keep the following points in mind when using Wi-Fi.
• Only use networks you are authorized to use.
This product searches for Wi-Fi networks in the vicinity and displays the results on the screen. Networks you are not authorized to use (unknown networks) may also be displayed. However, attempting to connect to or using such networks could be regarded as unauthorized access. Be sure to use only networks you are authorized to use, and do not attempt to connect to other unknown networks.
If security settings have not been properly set, the following problems may occur.
• Transmission monitoring
Third parties with malicious intent may monitor Wi-Fi transmissions and attempt to acquire the data you are sending.
• Unauthorized network access
Third parties with malicious intent may gain unauthorized access to the network you are using to steal, modify, or destroy information.
Additionally, you could fall victim to other types of unauthorized access such as impersonation (where someone assumes an identity to gain access to unauthorized information) or springboard attacks (where someone gains unauthorized access to your network as a springboard to cover their tracks when infiltrating other systems).
To prevent these types of problems from occurring, be sure to thoroughly secure your Wi-Fi network.
Only use this camera’s Wi-Fi function with a proper understanding of
Wi-Fi security, and balance risk and convenience when adjusting security settings.
The camera can print to PictBridge-compatible printers via Wi-Fi. PictBridge technical standards make it easy to connect digital cameras, printers, and other devices directly. Additionally, a new standard called DPS over IP enables PictBridge connections in network environments, and the camera is also compatible with this standard.
Trademarks and Licensing
• Microsoft and Windows are trademarks or registered trademarks of
Microsoft Corporation in the United States and/or other countries.
• Macintosh and Mac OS are trademarks of Apple Inc., registered in the
U.S. and other countries.
• App Store, iPhone, and iPad are trademarks of Apple Inc.
• The SDXC logo is a trademark of SD-3C, LLC.
• Wi-Fi ® , Wi-Fi Alliance ® , WPA™, WPA2™ and Wi-Fi Protected Setup™ are trademarks or registered trademarks of the Wi-Fi Alliance.
• The N-Mark is a trademark or registered trademark of NFC Forum, Inc. in the United States and in other countries.
• All other trademarks are the property of their respective owners.
• This device incorporates exFAT technology licensed from Microsoft.
• This product is licensed under AT&T patents for the MPEG-4 standard and may be used for encoding MPEG-4 compliant video and/or decoding
MPEG-4 compliant video that was encoded only (1) for a personal and non-commercial purpose or (2) by a video provider licensed under the
AT&T patents to provide MPEG-4 compliant video. No license is granted or implied for any other use for MPEG-4 standard.
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
142
Disclaimer
• Unauthorized reproduction of this guide is prohibited.
• All measurements based on Canon testing standards.
• Information subject to change without notice, as are product specifications and appearance.
• Illustrations and screenshots in this guide may differ slightly from the actual equipment.
• The above items notwithstanding, Canon cannot be held liable for any loss arising from the use of this product.
Before Use
Basic Guide
Advanced Guide
Camera Basics
Auto Mode
Other Shooting
Modes
P Mode
Playback Mode
Wi-Fi Functions
Setting Menu
Accessories
Appendix
Index
143
advertisement
Key Features
- Compact camera 20 MP CCD Blue
- Image sensor size: 1/2.3"
- Image stabilizer
- Optical zoom: 10x Digital zoom: 4x
- TTL
- ISO sensitivity (min): 100 ISO sensitivity (max): 1600 Fastest camera shutter speed: 1/2000 s Slowest camera shutter speed: 15 s ± 2EV (1/3EV step)
- Video recording 1280 x 720 pixels HD
- Built-in microphone PictBridge Mini-USB B Wi-Fi Near Field Communication (NFC)
- Lithium-Ion (Li-Ion)
Related manuals
advertisement