ONKYO TX-NR3030 Owner's manual

TX-NR3030
AV RECEIVER
Basic Manual
Advanced Manual found here
http://www.onkyo.com/manual/txnr3030/adv/en.html
En
Before Start
Advanced Manual
Advanced Manual is always updated with the latest
information and its user friendly interface, which does not
matter whether you access from PC or Smartphone, helps
you to understand more deeply about the AV Receiver.
Advanced Manual is consisted of the following chapters.
r Details on AM/FM Playback
r Playing Music Files on a USB Storage Device
r Listening to Internet Radio
r Playing Music with DLNA
r Playing Music Files in a Shared Folder
r Operating Music Files with the Remote Controller
r Listening Mode
r Advanced Settings
r Operating Other Components with the Remote Controller
r Advanced Connection
r Connecting and Operating Onkyo RI Components
r Control Function between the Unit and External
Component
r Firmware Update
r Troubleshooting
r Reference Information
Advanced Manual found here
http://www.onkyo.com/manual/txnr3030/adv/en.html
2
Supplied Accessories
Indoor FM antenna --- (1)
AM loop antenna --- (1)
Color labels for speaker cable --- (1)
Speaker Cable
1
r Equipped with 11 channel amplifier
r Supports playback in Dolby Atmos format which provides
360-degree placement and movement of sounds
including overhead sound
r Dolby Surround listening mode expands 2 ch, 5.1 ch or
7.1 ch source to available speaker configurations
r THX Select2 Plus certified
r Incorporates Qdeo™ technology for HDMI video
upscaling
r All HDMI jacks support displays of 4K resolution at 60 Hz
r Supports the HDMI Through function which allows
transmission from playback devices to the TV in standby
state
r Supports HDCP2.2, a strict copy-protection for providing
high quality content (HDMI IN3/OUT MAIN only)
r Supports ARC (Audio Return Channel)
r Supports USB storage playback
r Supports variety of network functions such as Internet
Radio, DLNA, etc.
r Supports Wi-Fi, Bluetooth and MHL-enabled mobile
device
r Bi-Amping capability
r A/V Sync function to correct deviation of audio and video
r Multi-zone function which allows you to play a different
source in another room from the main room (Video can
also be played in Zone 2)
r 32 bit DSP (Digital Signal Processor) with excellent
calculation performance
r Music Optimizer™ for Compressed Digital Music files
r Phase Matching Bass System
r Automatic speaker setup available using supplied
calibrated microphone (AccuEQ Room Calibration)
r Supports playback of MP3, FLAC, WAV, Ogg Vorbis,
Apple Lossless, DSD via network and USB storage
device (the supported formats will differ depending on
the use environment)
r ISF (Imaging Science Foundation) Video Calibration
2
Features
The Basic Manual leads you through the fundamental steps
to enjoy the AV Receiver from connections to TV, speaker
system and playback components, to necessary functions
for playback. As well as that, Basic Manual informs you with
the instructions on frequently used functions. Besides, there
is another part of the manual called Advanced Manual to
inform you with more detailed information, which we have
decided to publish on the web from the ecological point of
view.
3
About the Basic Manual
Remote controller (RC-884M) --- (1)
Batteries (AA/R6) --- (2)
Power cord --- (1)
Speaker setup microphone --- (1)
¼
The number in parenthesis indicates the quantity. On packaging, the letter
at the end of the product name indicates the color.
How to use the remote controller
Remote control sensor
AV Receiver
Batteries (AA/R6)
About
|HV
O
¼
If you do not use the remote controller for a long time, remove the
batteries to prevent leakage.
¼
Note that keeping consumed batteries inside may cause corrosion
resulting in damage of the remote controller.
Step 1: Connections
TV
Personal computer
HDMI
IN
HDMI
OUT
To use the ARC function, connect to the ARC
compatible HDMI jack of the TV and make an
appropriate setting on the unit. See "2nd Step :
Source Connection" of "Step 2: Setting Up".
HDMI cable
HDMI
OUT
HDMI
OUT
HDMI
OUT
Game console
1
HDMI
OUT
Set-top box/Digital
video recorder, etc.
Blu-ray Disc/DVD player
Satellite/Cable
set-top box, etc.
For how to make settings, see the Advanced Manual.
Connecting the TV and players
Important: The power cord must be connected only after all
other connections are completed.
HDMI Cable Connection
The unit has many HDMI jacks on its rear panel and each
of them corresponds to an input selector button of the same
name on the front panel. For example, a Blu-ray Disc player
will be connected to the IN 1 jack and the BD/DVD button
on the front panel will be used to listen to the playback
sound (if the player is CEC compliant, input will be switched
automatically). If you add another Blu-ray Disc player, you
can use any other jack than IN 1. It is possible to change
assignment of the input jacks and input selector buttons.
To connect the TV and the unit, connect the HDMI OUT MAIN
jack of the unit and the HDMI IN jack of the TV using an HDMI
cable. With this connection, it becomes possible to display
the setting screen of the unit on the TV or transmit video/
audio signals from the player to the TV. If your TV supports
ARC (Audio Return Channel), it is possible to play the TV
sound with the AV receiver's speakers with this connection
only. If your TV does not support ARC, you need, in addition
to the HDMI OUT MAIN jack connection, a digital optical cable
connection between the digital audio out optical jack of the
TV and the DIGITAL IN OPTICAL jack of the unit or an analog
audio (RCA) cable connection between the audio output jack
of the TV and the TV/CD analog audio input jack of the unit.
z
Audio connection with a TV not supporting ARC
¼ Select an appropriate
connection for your TV.
TV
DIGITAL
OPTICAL
OUT
AUDIO
OUT
Another TV can be connected to the HDMI OUT SUB jack.
In this case, press MONITOR OUT on the main unit several
times to display "SUB" or "MAIN+SUB" and select the
output method. You can also enjoy using Zone function with
the HDMI OUT ZONE 2 jack. For details, see the section 6
"Using the multi-zone function" of "Step 3: Playing Back".
3
Step 1: Connections
The unit supports the HDMI Through function that allows
transmission from players to the TV even if the unit is in
standby. You have to modify the settings to enable the input
selection link with CEC compliant device, connection with
ARC compatible TV, and HDMI Through function. See "2nd
Step : Source Connection" of "Step 2: Setting Up".
r To enjoy HDCP2.2 protected video, connect the player to
the IN3 jack and the TV to the HDMI OUT MAIN jack of
the unit. Your player and TV need to support HDCP2.2.
r To play 4K or 1080p video, use the high speed HDMI cable.
r It is possible to send video and audio of an MHL-enabled
mobile device by connecting the MHL-enabled mobile device
to the AUX INPUT HDMI/MHL jacks on the front panel.
Connecting Components without HDMI
If your AV component does not have HDMI jack, use an
available jack of your component for cable connection with
this unit. Just as the HDMI jacks, other jacks on this unit have
a preassigned input selector button on the front panel. See
the name of the input selector button shown with the jack
when connecting the device.
1
5
4
6
„ Audio signal connection
1 Digital connection: Use a digital optical cable
(OPTICAL) or digital coaxial cable (COAXIAL) for
connection with a player.
Digital optical cable (OPTICAL)
¼
As the digital in optical jack of the unit has a
cover, push in the cable against the cover as it is
turned inside.
Digital coaxial cable (COAXIAL)
2 Analog connection: Use an analog audio (RCA) cable
for connection with a player.
To enjoy multi-zone playback of audio of a CD player
or such other player without HDMI output jack, you
need to use the analog audio (RCA) cable to connect
the corresponding jacks of the player and this unit.
For details on the multi-zone function, see the section
6 "Using the multi-zone function" of "Step 3: Playing
Back".
5 Use a composite video cable to connect a TV with
composite video input jack or a player with composite
video output jack.
Composite video cable
6 Use an analog RGB cable to connect the unit with a PC.
Analog RGB cable
¼
Video signals from the PC connected with the PC IN port will be
output only to a TV connected with the HDMI OUT MAIN/SUB/
<10'|LCEM
Video signals input to the composite video input jack,
the COMPONENT VIDEO input jack, or the PC IN
port will be upconverted to HDMI signals and then
output from the HDMI output jack. Note that it is
not possible to convert digital audio input signals to
analog or vice versa.
Analog audio (RCA) cable
3 Connection with turntable: If it uses an MM type
cartridge and does not have a built-in audio equalizer,
connect it to the 3 PHONO jack. If the connected
turntable has a built-in audio equalizer, connect it to the
2 TV/CD jack.
¼
If it uses an MC type cartridge, install an audio equalizer compatible
with MC type cartridge between the unit and the turntable by
connecting it to the 2 TV/CD jack. For details, refer to the turntable's
instruction manual.
¼
If the turntable has a ground wire, connect it to the GND terminal of
this unit. If connecting the ground wire increases noise, disconnect it.
„ Video signal connection
The unit has a video upconversion function. For details, see
the section on the right.
4 Use a component video cable to connect a TV
3
2
with component video input jacks and a player with
component video output jacks.
Component video cable
¼
Its transmitted video has higher quality than that
of composite video cable.
4
AV Receiver
¼
If multiple video signal inputs are put into one input
system, the output will be made in the order of HDMI,
component video, and composite video.
Step 1: Connections
2
Height speakers 1 and 2: Placing 9F or
GH speakers produce surround effects on
a height plane.
r To enjoy the Dolby Atmos listening
mode, Height 1 speakers or surround
back speakers need to be installed.
r Although Height 1 speakers can
enhance surround effects, we
recommend you to add Height 2
speakers in order to ensure full effects.
r Install Height speakers such as Front
High and Rear High speakers on the
upper part of the front or rear wall. There
are other types of Height speakers.
Connecting speakers
Speaker layout
9
F
"
I
J
#
$
'
&
%
Wide speakers: Placing IJ speakers
makes the front sound field even wider. It
also give smoother transitions between
front and back surround sounds.
H
G
8
7
To enjoy the Dolby Atmos listening mode,
Height 1 speakers or surround back
speakers need to be installed.
" # Front speakers
Center speaker
$
% & Surround speakers
Subwoofer
'
7 8 Surround back speakers
9 F Height 1 speakers (Front High)
G H Height 2 speakers (Rear High)
I J Wide speakers
r GH and IJ share the same speaker
terminals. Select either of the groups.
r To use the multi-zone function, see the
section 6 "Using the multi-zone function"
of "Step 3: Playing Back".
5.1 ch: Connect the speakers
" # $ % & ' to the unit. " # output
front stereo sound. $ outputs center
sounds such as dialogs and vocals. % &
create back sound field. ' reproduces
bass sounds and creates rich sound field.
Up to four subwoofers can be connected to
the unit.
Surround back speakers: Placing
78URGCMGTUCNNQYURNC[DCEMKP|EJ
configuration that improves sense of
envelopment created by back sound field.
It also improves seamlessness of back
sounds and provides more natural sound
experiences in the sound field.
Height speakers arrangements
(Dolby Atmos)
There are several types of Height speakers
other than those mentioned in the previous
section. See the next section "Combination
patterns of Height speakers 1 and 2" and
select the combination pattern from those
specified for Height speakers 1 and Height
speakers 2.
r This unit performs optimal sound field
processing for the type of Height speakers
1 and 2 which is registered in initial
settings (with setup wizard) according to
an actual speaker layout. Note that the
optimal effect cannot be achieved if you
place Height speakers in a combination
pattern other than those specified.
r Dolby recommends to place the speakers
as described on “Installing speakers in
ceiling” to obtain the best Dolby Atmos
effect.
Using Dolby Enabled Speakers
c
ab
cd
ef
a
b
e
f
d
Dolby Enabled Speaker (Front)
Dolby Enabled Speaker (Surround)
Dolby Enabled Speaker (Back)
A Dolby Enabled Speaker is specially designed
to be used as a Height speaker. There are two
types of Dolby Enabled Speakers, the one is to
be placed on the top board of other speakers
such as front speakers and surround speakers,
and the other is integrated type with the normal
speakers. Dolby Enabled Speakers designed
with their output facing toward the ceiling to
create an elevated audio effect in the Dolby
Atmos and Dolby Surround listening modes by
providing sounds echoing off the ceiling.
Installing speakers in ceiling
k
l
i
j
g
gh
ij
kl
h
Top Front
Top Middle
Top Rear
5
Step 1: Connections
Ceiling speakers, etc. are used for maximizing effects in
Dolby Atmos or Dolby Surround listening mode. Install
Top Front speakers midway between the position just
above the listening position and the position just above
the front speakers. Install Top Middle speakers just above
the listening position. Install Top Rear speakers midway
between the position just above the listening position and
the position just above the surround back speakers.
5
Surround R
8
Surround back R
4
Surround L
7
Surround back L
If you use only one surround
back speaker, connect it to
the BACK L terminal.
Combination patterns for Height speakers 1 and 2
Dolby recommends the following combination pattern
to obtain the best effect of Dolby Atmos and Dolby
Surround listening modes.
r Pair 1: Top Middle
r Pair 2: Top Front / Top Rear
The following are the patterns of Height speakers 2 that
can be selected according to the type of Height speakers 1.
Height speakers1: Front High
Height speakers 2: Not Use/Top Middle/Rear High/Dolby
Enabled Speaker (Surround)/Dolby Enabled Speaker (Back)
Height speakers1: Top Front
Height speakers 2: Not Use/Top Rear
Height speakers1: Top Middle
Height speakers 2 cannot be used.
Height speakers1: Dolby Enabled Speaker (Front)
Height speakers 2: Not Use/Dolby Enabled Speaker
(Surround)/Dolby Enabled Speaker (Back)
Height speakers1: Dolby Enabled Speaker (Surround)
Height speakers 2 cannot be used.
Height speakers1: Dolby Enabled Speaker (Back)
Height speakers 2 cannot be used.
r When front speakers are bi-amp connected, you can select
a pattern for Height speakers 2 from the following options.
Not use/Front High/Top Front/Top Middle/Dolby Enabled
Speaker (Front)/Dolby Enabled Speaker (Surround)/Dolby
Enabled Speaker (Back)
6
F
Height 1 R
H
Height 2 R/
J
Wide R
1
Front R
2
Front L
Instructions on how to connect speakers
Important%QPPGEVURGCMGTUYKVJŝVQŝKORGFCPEG
You have to change the setting if any of the speakers have
ŝQTOQTGVQNGUUVJCPŝKORGFCPEG;QWECPUGVWRD[
viewing the guidance displayed on the TV screen. Press
RECEIVER and then HOME on the remote controller.
Select "Setup" - "2.Speaker Setup" - "Speaker Settings" "Speaker Impedance" and change the default value from
"6ohms" to "4ohms".
r Select the item with the cursor buttons of the remote
controller and press ENTER to confirm your selection. To
return to the previous screen, press RETURN.
G
Height 2 L/
I
Wide L
9
Height 1 L
3
Center
1/2"-5/8"(12-15 mm)
Cut and remove the plastic coating from the end of the
speaker cable, twist the core and connect it to the terminal.
Make correct connection between the unit's jacks and
speaker's jacks (+ to + and - to -) for each channel. If
connection is wrong, a bass sound may become poor
due to reverse phase. Attaching the supplied colored
speaker cable labels to the + side on the both ends of each
channel's cable will help correct connection.
Connecting the Subwoofer
Up to four subwoofers with built-in power amplifier can
be connected to the subwoofer jacks. Set the cut-off
filter selection switch of the subwoofer to DIRECT. If the
subwoofer does not have a cut-off filter selection switch
Step 1: Connections
but has a cut-off frequency adjusting dial, turn it to the
maximum frequency. If your subwoofer does not have builtin power amplifier, you can connect a power amplifier
between the unit and the subwoofer.
3
Network Connection
Other connections
AM/FM Antenna Connections
Connect the antennas to listen to AM/FM broadcast. When
listening to the broadcast for the first time, adjust the
antenna position and orientation to get the best reception.
You can enjoy Internet radio and DLNA by connecting
the unit to LAN. The unit can be connected to the router
with an Ethernet cable or to the wireless LAN router with
Wi-Fi connection. In case of wired connection, connect
the Ethernet cable to the Ethernet port. See "4th Step :
Network Connection" of "Step 2: Setting Up".
Internet radio
AM loop
antenna
(supplied)
Subwoofer with built-in
power amplifier
r The speaker setting is 7.2 ch at the time of purchase. You
can change it manually or by using automatic speaker
setting.
r Short-circuiting the + cable and - cable or contacting the
cable core to the rear panel of the unit may cause failure.
Also do not connect two or more cables to one speaker
terminal or one speaker to several terminals.
r Using a speaker with less impedance than the setting
may result in failure.
Router
Indoor FM antenna
(supplied)
PC
NAS
Fix with a tack on
the wall.
(North American models)
(European and Asian
models)
Assemble the AM loop antenna (supplied).
Headphones Connection
%QPPGEVUVGTGQJGCFRJQPGUYKVJCUVCPFCTFRNWI
|KPEJ
QTÔ|OOVQVJG2*10'5LCEMQPVJGHTQPVRCPGN
Sound from the speakers will be off while you are using the
headphones.
r If you selected any other listening mode than Pure Audio,
Stereo, Mono and Direct, connecting headphones will
switch the listening mode to Stereo.
When using commercially available banana plugs:
tighten the speaker terminals to the end and then insert the
banana plugs. Do not insert the cable core directly into the
hole for banana plug of speaker terminal. (North American
model)
7
Step 2: Setting Up
Important: When the unit is turned on for the first time, the
setup wizard of the section 2 will automatically be launched.
If you use the setup wizard to make the initial setup,
connect a TV to the HDMI OUT MAIN or SUB jack of the
unit via HDMI connection.
1
Turning the power on
Connect the power cord to the outlet. Press zON/
STANDBY on the main unit or zRECEIVER on the remote
controller to turn the unit on or to standby mode.
2
Making the Initial Setup with the Setup Wizard
Read before starting the procedure: Set up by
answering the guidance displayed on the TV screen.
Select the item with the cursor buttons of the remote
controller and press ENTER to confirm your selection.
To return to the previous screen, press RETURN.
r If you terminate the procedure on the way or
change the setting made in the initial setup and
want to call up the setup wizard again, press
RECEIVER and then HOME on the remote
controller, select "Setup" - "7.Hardware Setup" "Initial Setup", and press ENTER.
r You cannot return to the previous screen during speaker
setup, even if you press RETURN.
r You cannot setup the wide speaker setting in the setup
wizard. For details on setting up the wide speakers, see
the Advanced Manual.
Initial Setup
AccuEQ Room Calibration
This step you can automatically calibrate
your room to get correct surround sound.
Would you like to cailbrate your room now
or later?
Do it Now
Do it Later
HOME
Select the language first. In the next screen, the summary
of the setup wizard as below will be displayed. Select "Yes"
in this screen and press ENTER on the remote controller.
Initial Setup
Language Select
English
Deutsch
Français
Español
Italiano
Nederlands
Svenska
HOME Exit
Initial Setup
Exit
1. Place the speaker setup microphone.
When the start screen above is displayed, before
starting the procedure, place the supplied speaker setup
microphone at the measurement position  by referring
to the figure below.
Welcome to initial setup. Have you connected all the speakers and devices?
Before starting, please connect speakers and sources.
Now, would you like to start initial setup?
TV
1st Step : AccuEQ Room Calibration
2nd Step : Source Connection
3rd Step : Remote Mode Setup
4th Step : Network Connection
¼
This unit includes a removable power cord. Connect the power
cord to AC INLET of the unit and then connect to the outlet. Always
disconnect the outlet side first when disconnecting the power cord.
When the unit is turned on, a large instantaneous current may
flow affecting functionality of the computer and other devices. It is
recommended to use a separate outlet from that for the computer or
such other sensitive devices.
Firmware update notification: If the unit is connected
via LAN and there is firmware update available, the
"Firmware Update Available" message will appear. To
execute updating, select "Update Now" with the cursor
buttons of the remote controller and press ENTER. When
"Completed!" appears, press zON/STANDBY on the main
unit to turn the unit into standby mode. Then updating will
be completed.
r The unit automatically turns itself into standby mode 3
minutes after "Completed!" appears on the display. In this
case also, updating will be completed.
8
Yes
No
HOME
Exit
The setup wizard proceeds in the four steps as below.
„ 1st Step : AccuEQ Room Calibration
„ 2nd Step : Source Connection
„ 3rd Step : Remote Mode Setup
„ 4th Step : Network Connection
„ 1st Step : AccuEQ Room Calibration
The test tone coming from each speaker will be measured to
enable setting of the number of speakers, volume level, each
speaker's optimum crossover frequencies, and distance from
the primary listening position, and also enable correction of
distortion caused by the room acoustic environment.
Listening area
Measurement position
with microphone
¼
Correct measurement will not be possible if the microphone is held
by hand. Measurement is not possible if headphones are being used.
¼
The subwoofer sound may not be detected since it is extremely low
frequencies. Raise the subwoofer volume to around the half of its
maximum volume and make its frequency to the maximum level.
¼
A loud test tone will be heard during measurement. Measurement
may be interrupted if there is ambient noise or radio frequency
interference. Close the window and turn off the home appliance and
fluorescent light.
Step 2: Setting Up
2. After placing the microphone at the measurement
position, select "Do it Now" with the cursors and
press ENTER.
3. Connect the microphone to the SETUP MIC jack of
the unit.
SETUP MIC jack
Speaker
setup
microphone
4. Follow the guidance displayed on the TV screen.
6. When the measurement is completed, the
measurement result is displayed.
Press W/X on the remote controller to check the
settings. Press ENTER with "Save" selected. In the next
screen showing that "AccuEQ Room Calibration" is
"On", press ENTER on the remote controller.
r If there is an error message, follow the on-screen
instruction to remove the error cause.
About THX playback
THX recommends setting the speakers manually if
you use THX-certified speakers or playing back with
THX listening modes.
r THX recommends setting the crossover frequency to
“80Hz(THX)” manually.
r Due to the electrical complexities and the
interaction with the room, you may notice irregular
results when setting the level or distance of each
speaker. If this happens, THX recommends setting
the speakers and the subwoofer manually.
r If you select "No" and press ENTER, the error cause
will be displayed. Follow the guidance to remove the
error cause and check the connection again.
4. Select "Yes" with the cursors and press ENTER
on the remote controller to check the connection
of other inputs or select "No, Done Checking" and
press ENTER to skip.
If you select "Yes", you will return to the screen of step 2.
If you select "No, Done Checking", you will proceed to step 5.
5. Enabling HDMI Linked Operation and Other Functions
In the next screen, you can enable the HDMI linked
operation with CEC compliant device, connection with ARC
compatible TV, and HDMI Through function. Select "Yes"
with the cursors to enable them or "No, Done Checking" to
skip, and press ENTER on the remote controller.
6. Select "Yes" with the cursors and press ENTER to
enable the CEC link function or select "No" and
press ENTER to keep it disabled.
AccuEQ Room Calibration
Source Connection
Normal
Front Speakers Type
Height 1 Speakers Type
Not Use
Height 2 Speakers Type
Not Use
7. When "Please unplug setup microphone." is
displayed, disconnect the microphone.
The following CEC-compatible devices are found;
Do you wish to turn on the CEC link?
Integra DHS-8.8
REAR PANEL
SURROUND
R
WIDE
R
BACK
R
FRONT R
FRONT L
BACK
L
WIDE
L
„ 2nd Step : Source Connection
SURROUND
L
Set bi-amp only if you use 2 channel amp for each front speaker.
ENTER
Yes
Next
When the screen above is displayed, set the items with the
cursors on the remote controller. Select the types for height
1/2 speakers if the height speakers are used. After front and
height speakers types are selected, switch the screen using
cursor l to select the type of subwoofer. After setting the
items, press ENTER on the remote controller. Press ENTER
again in the next screen to start automatic speaker setting.
r Speaker terminals and settings description display
at the bottom of the screen as you move the cursor
to each item. Please refer to this information on the
screen.
5. The test tones sound from the connected speakers
and automatic speaker setting starts.
Measurement will be made twice for each speaker. It takes
several minutes to be completed. Keep the room as quiet
as possible during measurement. If any of the speakers
do not produce the test tone, check for disconnection.
r During measurement, each speaker outputs the test
tones at a high volume. Be careful of sound leak
that may disturb your neighbors, or be careful not to
frighten young children.
You can check whether or not each input source is
connected correctly.
1. When the Source Connection start screen is displayed,
select "Yes, Continue" with the cursors and press ENTER.
No
HOME
Exit
If you select "Yes", the connection with ARC compatible TV
and HDMI Through function will be set to "Auto" and enabled.
Initial Setup
„ 3rd Step : Remote Mode Setup
Source Connection
This step will start to check if the
connections were made correctly.
Would you like to continue?
Initial Setup
Remote Mode Setup
Preprograming remote will give you control
of other devices from AV receiver remote
Yes, Continue
Would you like to setup your remote to
No. Skip
HOME
Exit
control your devices? This may take a while
depending on what and how many you have
connected. You can always come back to remote
setup from setup “8-2 Remote Mode Setup”.
2. Select the desired input to check the connection and
press ENTER.
Start playback of the selected device. If connection is
correct, video/audio of the input source selected on the
unit will be played.
3. After checking the connection, select "Yes" with the
cursors and press ENTER.
Yes
No. Skip
HOME
Exit
In this step, you can enable operation of the other components
using the remote controller of the unit. When the Remote
Mode Setup start screen is displayed, select "Yes" with the
9
Step 2: Setting Up
cursors and press ENTER on the remote controller. Follow
the guidance to select the desired REMOTE MODE button
and in the keyboard screen, enter the first three characters of
the brand name of the device you are going to program (e.g.,
"ONK" for ONKYO) and search for the remote control code.
The guidance will also explain how to set the remote controller.
2. Select and set the authentication method.
The "Enter Password" screen may be displayed, instead
of the screen shown below, if the access point device
does not have an automatic setting button.
Wi-Fi Setup
Select the authentication method.
„ 4th Step : Network Connection
Initial Setup
Network Connection
Enter Password
Do you want to connect network connection?
Push Button
It gives you network services that our AV
PIN code
receiver support. If you wish to skip this step.
select “No. Skip”.
Yes
No. Skip
HOME
Exit
You can check the network connection and make the WiFi setting. When the Network Connection start screen is
displayed, select "Yes" with the cursors and press ENTER
on the remote controller. If you select "Wired" in the next
screen, you can view the Ethernet cable connection status.
To make the Wi-Fi setting, select "Wireless", press ENTER
on the remote controller and follow the sections below.
Make the following preparations.
Wi-Fi connection requires an access point such as
wireless LAN router (¼). Write down the SSID and
password (key) of the access point if they are shown
in the label of the main body. If the access point has
an automatic setting button (may be called differently
according to the manufacturer), you can set up
without inputting the password. For how to use the
automatic setting button of the access point, refer to
its instruction manual.
¼
The unit supports Wi-Fi connection with 2.4 GHz
access point.
1. Select the SSID of the access point to be connected
with the cursor buttons and press ENTER.
When the SSID of the access point appears on the TV
screen, select the desired access point.
r If you changed the initial setting of the access point to
skip password entry, step 3 starts automatically.
r If you changed the initial setting of the access point
to hide the SSID, see "When the access point is not
displayed".
10
When the screen above is displayed, select and set one
of the three authentication methods: "Enter Password",
"Push Button" and "PIN code". See below for details of
and how to set each method.
Enter Password: Enter the password of the access point to
establish connection.
1 Select "Enter Password" with the cursor buttons and
press ENTER.
2 Enter the password (¼) on the keyboard screen, select
"OK" with the cursor buttons and press ENTER.
¼
Select "Shift" and press ENTER to toggle between upper and lower
case. Select "" or "" and press ENTER to move the cursor to the
selected direction. Select "Back Space" and press ENTER to delete
the character at the left of the cursor position. To select whether to
mask the password with "¼" or display it in plain text, press D on the
remote control. Press + 10 on the remote controller to enable the
"Shift" function and CLR to delete all the input characters.
3 If the security method of the access point to be
connected is WEP, select "Default Key ID", select "OK"
and press ENTER.
Push Button: Use the automatic setting button of the
access point to establish connection.
1 Select "Push Button" with the cursor buttons and press
ENTER.
2 Hold down the automatic setting button of the access
point for the necessary seconds, select "OK" with the
cursor buttons and press ENTER.
PIN code: Select this method when the automatic setting
button of the access point is beyond the reach. Select "PIN
code" with the cursor buttons and press ENTER to display
the 8-digit PIN code. Register the displayed PIN code to the
access point, select "OK" with the cursor buttons and press
ENTER. For how to register the PIN code to the access
point, refer to its instruction manual.
3. Establish connection.
The connection process starts and the Wi-Fi indicator
on the left of the unit's display starts flashing. When
connection has been established, the Wi-Fi indicator
changes from flashing to staying lit. If the Wi-Fi indicator
does not stay lit, connection has not been established.
Make the setting again. If "Push Button" does not work,
try "Enter Password".
When the access point is not displayed
Select "Other..." with the c cursor on the remote
controller and press ENTER to display the keyboard
screen. Input the SSID and password. Make the
following settings according to the router setting.
„ WPA/WPA2 method
Select "WPA" or "WPA2" in "Security Method", select
"OK" and press ENTER.
„ WEP method
Select "WEP" in "Security Method" and select
"Default Key ID". Then select "OK" and press ENTER.
r If encryption setting has not been made on the
wireless LAN router, select "None" in "Security
Method", select "OK" and press ENTER.
„ Exiting the setup wizard
After finishing the initial setup, keep "Finished" selected
and press ENTER on the remote controller. Connection and
setting of the unit is now completed. See Step 3 and enjoy
your home theater.
Step 3: Playing Back
1
Playing the player and TV
2 RED
RECEIVER SOURCE
ZONE 3 GREEN
1
SLEEP
7
8
Remote Controller Parts Name
1 zRECEIVER button: Turns the unit on or into standby
mode.
2 RED
RECEIVER SOURCE
ALL OFF
ZONE 3 GREEN
SLEEP
ALL OFF
MY MOVIE
MY TV
CBL/SAT
STB/DVR
GAME
PC
AUX
TV/CD
PHONO
USB
BLUETOOTH
RECEIVER
MUTING
NET
TUNER
TV
TV
VOL
MY TV
2 REMOTE MODE/INPUT SELECTOR button: Switches
MY MUSIC
REMOTE MODE / INPUT SELECTOR
REMOTE MODE
MODE
MY MOVIE
MY MUSIC
REMOTE MODE / INPUT SELECTOR
BD/DVD
BD/DVD
CBL/SAT
STB/DVR
GAME
PC
AUX
TV/CD
PHONO
TUNER
NET
USB
BLUETOOTH
RECEIVER
MUTING
the input to be played.
3 Cursor buttons and ENTER button: Moves the cursor
CH
DISC
VOL
ALBUM
INPUT
TOP MENU
RECEIVER
MENU
PREV CH
GUIDE
PLAYLIST
ENTER
PLAYLIST
Q
SETUP
HOME
2
RETURN
9
and confirms the selection.
4 Q SETUP button: Displays the Quick Setup menu that
REMOTE MODE
z To control the unit: The remote controller of this unit has
the remote mode function for controlling other devices. You
cannot control this unit when the remote controller is in the
remote mode other than RECEIVER mode (for controlling
this unit). Be sure to press 9 RECEIVER to select the
RECEIVER mode before starting operation.
1. Turning the power on
Press 1 zRECEIVER on the remote controller to turn
the power on.
r Switch the input on the TV to that assigned to the
unit. Use the TV's remote controller.
2. Select the input of the unit and start playback on the
player or TV.
r Press 2 INPUT SELECTOR to which the desired
player has been assigned. Press TV/CD to play the
TV's sound. You can also use the input selector
buttons on the main unit.
r Input will automatically be selected if the TV or player
is CEC compliant and connected to the unit with
HDMI cable.
3. Select the desired listening mode.
Press 5 listening mode buttons to switch the mode so
that you can enjoy different listening modes. For details
about the listening modes, see "Listening modes" on the
next section.
4. Adjust the volume with G.
MODE
TV
TV
VOL
F
CH
DISC
VOL
ALBUM
INPUT
TOP MENU
3
4
G
5
6
MENU
GUIDE
7
PREV CH
PLAYLIST
PLAYLIST
ENTER
H
Q
SETUP
RETURN
HOME
I
8
9
F
G
H
5
SEARCH
REPEAT
RANDOM
MODE
MOVIE/TV
MUSIC
GAME
THX
1
2
3
4
5
6
7
6
8
10
+10
I
J
r The buttons other than 1 to J are for operating other
devices.
9
11
0
D.TUN
DIMMER
12
CLR
allows you to set the frequently used functions including
input selection and volume adjustment.
Listening mode buttons: Allows you to select the
listening mode.
DIMMER button: Switches the brightness of the display.
This button also turns MASTER VOLUME indicator on
and off.
ZONE button: For use when the unit is connected with
an integrated amplifier in a separate room and sound is
played there.
SLEEP button: Sets the time until the unit enters
standby mode automatically.
RECEIVER button: Switches the remote controller to
the mode for operating this unit.
MUTING button: Temporarily mutes audio.
VOLUME buttons: Allows you to adjust the volume. This
button also cancels the muting.
RETURN button: Returns the display to the previous
state.
HOME button: Displays the Home menu that allows you
to make advanced settings and use Internet radio and
DLNA.
DISPLAY button: Switches the information on the
display.
J
DISPLAY
RC-884M
11
Step 3: Playing Back
Listening Modes
You can select a listening mode from various options such
as Dolby Digital, Dolby Atmos and DTS. Select the desired
mode by switching and listening actual sound in different
modes. The selectable listening modes depend on the
format of the input signals.
MOVIE/TV: You can select a listening mode suitable for
movies and TV programs.
MUSIC: You can select a listening mode suitable for music.
GAME: You can select a listening mode suitable for games.
THX: You can select a THX listening mode.
PURE AUDIO (main unit only): The display and analog
video circuits are cut off to provide purer sound.
r For details on the listening modes, see the Advanced
Manual.
"Direct" for playing the input signals as-is
Selecting this mode allows the input signals to be
played as they are. For example, 2 ch signals of music
CD will be played in stereo, 5.1 ch signals in 5.1 ch,
and Dolby Digital signals of blu-ray disc or DVD in the
Dolby Digital sound field according to the specified
number of channels.
Other Useful Functions
„ Playing Video and Audio from Different Sources: It is
possible to play audio and video from different sources. For
example, you can play audio from the CD player and video
from the BD/DVD player. In this case, press BD/DVD and
then TV/CD. Then start playback on the BD/DVD player and
CD player. This function is effective when an input with audio
only has been selected (TV/CD, TUNER or PHONO in the
initial setting).
12
„ Adjusting Sound Quality: It is possible to enhance
or moderate the low and high pitched ranges of front
speakers. Press TONE on the main unit several times to
select the desired setting from "Bass", "Treble", and "Phase
Matching Bass" and adjust with +/-.
r It cannot be set if the listening mode is Pure Audio, Direct
or THX.
"Bass": Allows you to enhance or moderate the low
pitched range.
"Treble": Allows you to enhance or moderate the high
pitched range.
"Phase Matching Bass": Allows you to keep the clear
midrange and effectively enhance the low pitched range.
„ Muting Temporarily: Press MUTING on the remote
controller. To cancel the muting, press MUTING again, or
press VOL j/l.
„ Changing the Display Brightness: Press DIMMER on
the remote controller. The display brightness changes each
time you press the button.
2
Listening to AM/FM Radio
The Basic Manual explains the method using automatic
tuning. For manual tuning, see the Advanced Manual.
1. Press TUNER on the main unit several times to
select either "AM" or "FM".
2. Press TUNING MODE on the unit, so that the "AUTO"
indicator on the display lights.
on the unit.
The automatic tuning to a radio station starts. Searching
stops when one is tuned. When tuned into a radio
station, the " TUNED " indicator on the display lights.
The "FM STEREO" indicator lights if the radio station is
an FM radio station.
3. Press TUNING
TUNED
AUTO
„ Checking the Input Format: Press DISPLAY on the
remote controller several times to switch the display of the
main unit in order of:
FM STEREO
Input source &
Listening mode
Signal format & Sampling
frequency
Input signal resolution & Output
resolution
r If "Dolby D 5.1" is displayed in signal format, the Dolby
Digital 5.1 ch signals are being input. When listening to
AM/FM radio, the band, frequency and preset number
are displayed.
(Actual display depends on the country.)
Registering an AM/FM Radio Station
It allows you to register up to 40 of your favorite AM/FM
radio stations.
1. Tune into the AM/FM radio station you want to
register.
2. Press MEMORY on the unit.
The preset number on the display flashes.
3. Repeatedly press PRESET
on the unit to select
a number between 1 and 40 while the preset number
is flashing (about 8 seconds).
4. Press MEMORY on the unit again.
When registered, the preset number stops flashing.
To select a preset radio station, press PRESET
QPVJGOCKPWPKVQT%*ŨQPVJGTGOQVGEQPVTQNNGT
Step 3: Playing Back
3
Connecting and playing the Bluetoothenabled device
You can wirelessly enjoy music files stored in a smartphone
or other Bluetooth-enabled device. The coverage area is
|HGGV
|OGVGTU
Playing Sound of the Bluetooth-enabled Device
If the unit is on and the Bluetooth-enabled device is
connected, the input will be automatically switched to
BLUETOOTH. Play music in this state.
r It may take about a minute until connection is established
when the unit is on since the Bluetooth function takes
some time to start up.
r If the volume setting on the Bluetooth-enabled device is
low, the sound will not be output from this unit.
r Due to the characteristics of Bluetooth wireless
technology, the sound produced on this unit may slightly
be behind the sound played on the Bluetooth-enabled
device.
4
Using the Home menu
In the Home menu, you can make advanced setup and
use Internet radio and DLNA function. For details on the
operation, see the Advanced Manual.
1. After pressing RECEIVER, press HOME on the
remote controller.
The Home menu is displayed on the TV screen. You can
also use the HOME button on the main unit.
HOME
r The Bluetooth-enabled device needs to support the
A2DP profile.
r This unit is compatible with SCMS-T copy protection
scheme. It is possible to playback the music of Bluetoothenabled devices that support SCMS-T protection
scheme.
r Note that connection is not always guaranteed with all
Bluetooth-enabled devices.
2. Select the item with the cursor buttons of the
Pairing
„ Sleep Timer: Select to turn the unit into standby mode
automatically when the specified time elapses.
Pairing is necessary when using the Bluetooth-enabled
device for the first time. Before starting the procedure, learn
how to enable the Bluetooth setting function and to connect
with other devices on the Bluetooth-enabled device.
1. Press BLUETOOTH on the remote controller.
The unit enters the pairing mode and the BLUETOOTH
indicator starts flashing.
2. While the BLUETOOTH indicator is flashing (about
|OKPWVGUEQORNGVGEQPPGEVKQPQPVJG$NWGVQQVJ
enabled device in the nearby area.
If the name of this unit is displayed on the Bluetoothenabled device's display, select this unit. Paring will be
completed after a short time.
r If a password is requested, enter "0000".
r When connecting the unit to any other Bluetoothenabled device, start pairing by holding down
BLUETOOTH until the BLUETOOTH indicator starts
flashing. This unit can store the data of up to ten
paired devices.
Setup
remote controller and press ENTER to confirm your
selection.
To return to the previous screen, press RETURN. To
return to the Home menu, press HOME.
„ InstaPrevue: Select to preview videos input from the
HDMI input jacks collectively in a single screen. The screen
has a main window (current input video) and sub windows
(other input videos). To switch the current input, select the
desired sub window with the cursor buttons and press
ENTER.
r A black sub window is shown for the input with no video
signals.
r "InstaPrevue" cannot be selected if the video is being
input from HDMI IN 5, 6 or 7 or if there is no signal from
the input currently selected.
r "InstaPrevue" cannot be selected if "Zone 2 Monitor Out"
is set to "Use" and Zone 2 is on.
r Depending on video signals, the picture may not be
properly rendered on the preview thumbnails.
„ Setup: You can change the assignment of input
terminals and input selector buttons and also make various
speaker settings and other advanced settings.
13
Step 3: Playing Back
„ Network Service: Select to use Internet radio services
and the DLNA function. When you connect the unit to the
network and press ENTER, the network service screen will
be displayed on the TV. On the TV screen, select the desired
service or music file with the cursors of the remote controller
and press ENTER to confirm and start playback.
Internet radio service: You can listen to TuneIn or such
other Internet radio stations registered in advance.
DLNA : You can play music files stored in the PC or
NAS device connected to the network. Select the server
with the cursors, select the desired music file and press
ENTER to start playback.
Home Media: You can play music files in a shared folder
on the PC or NAS device connected to the network.
Select the server with the cursors, select the desired
music file and press ENTER to start playback.
r "Network Service" becomes selectable after the network
starts up even if it cannot be selected first. It may take
about a minute to start up.
r When "Network Service" is selected for the first time,
the "DISCLAIMER" screen will appear on the TV. Select
"Agree" if you agree the content. If you do not agree the
content, you cannot use the network service.
¼
You cannot use the function unless the TV is connected via HDMI
since selecting "Agree" in the "DISCLAIMER" screen is not possible.
r Layout of the icons in the "Network Service" top menu
can be changed. Press NET on the remote controller
and press D. Select the source icon with the cursors and
press ENTER, and then select the destination icon and
press ENTER. The positions of the icons are switched
each other.
„ USB: Select "USB" in the TV screen and connect a
USB storage device to the USB port on the front panel. On
the TV screen, select the desired folder or music file with
the cursors of the remote controller and press ENTER to
confirm and start playback.
r "USB" becomes selectable after the USB function starts
up even if it cannot be selected first. It may take about a
minute to start up.
5
Using Quick Setup menu
In the Quick Setup menu, you can set frequently used
functions including input selection and volume adjustment.
1. Press Q SETUP on the remote controller.
The Quick Setup menu is displayed on the connected
TV's screen.
CBL/SAT
Input
BD DVD
Audio
CBL/SAT
Video
STB DVR
Information
GAME
Listening Mode
PC
AUX
2. Select the item with the cursor buttons of the
remote controller and press ENTER to confirm your
selection.
r To return to the previous screen, press RETURN.
„ Input: Select the input and check the assignment of
input selector buttons.
„ Audio: You can perform various audio settings including
audio quality and speaker level adjustment.
r You cannot select this item when audio is output from the
TV's speakers.
A/V Sync: If the video is behind the audio, you can
delay the audio to offset the gap. Different settings can
be set for each input.
r It cannot be set if the input is "NET", "USB" or
"BLUETOOTH".
r It cannot be set if the listening mode is Pure Audio or
Direct.
Bass, Treble: Adjust volume of the front speaker.
r It cannot be set if the listening mode is Pure Audio,
Direct or THX.
Phase Matching Bass: Suppress phase shift in the
midrange to enhance bass sound. Thus smooth and
powerful bass sound can be obtained.
r It cannot be set if the listening mode is Pure Audio,
Direct or THX.
14
Subwoofer 1/2 Level, Center Level: Adjust the speaker
level while listening to the sound. The adjustment you
made will be reset to the previous status when you turn
the unit to standby mode.
r The speakers cannot be adjusted if they have been
set to "No" or "None" in "Speaker Configuration".
r "Subwoofer 2 Level" cannot be adjusted if
"Subwoofer" have been set to "1ch" in "Speaker
Configuration".
AccuEQ Room Calibration: Disable the sound field
set in the automatic speaker setting. The setting can be
separately set to each input.
r This setting cannot be selected if the automatic
speaker setting has not been performed.
r It cannot be set if headphones are connected or the
listening mode is Pure Audio or Direct.
Late Night: Make small sounds to be easily heard. It
is useful when you need to reduce the volume while
watching a movie late night. You can enjoy the effect on
Dolby Digital and Dolby Digital Plus only.
r Turning the unit to standby mode will set the setting
to "Off".
r This function cannot be used if "Loudness
Management" is set to "Off".
Music Optimizer: Improve the quality of the
compressed audio. Playback sound of lossy
compressed files such as MP3 will be improved. The
setting can be separately set to each input.
r The setting is effective in the signals of 48 kHz or
less. The setting is not effective in the bitstream
signals.
r It cannot be set if the listening mode is Pure Audio or
Direct.
Re-EQ, Re-EQ (THX): Adjust the soundtrack that was
processed to enhance its high pitch range, in order to
make it suitable for home theater.
r In Re-EQ, the following listening modes can be used:
Dolby Digital, Dolby Digital Plus, Dolby TrueHD,
Multichannel, DTS, DTS-HD High Resolution Audio,
DTS-HD Master Audio, DTS Express, DSD, and DTS
Neo:X Cinema.
r In Re-EQ (THX), the following listening modes can
be used: THX Cinema, THX Surround EX, and THX
Select2 Cinema.
Step 3: Playing Back
Screen Centered Dialog: Height speakers are used to
move acoustic images such as dialogs from the center
speakers upward according to the height of the TV
screen. Acoustic images of the center speakers move
up as the set value is increased.
r This item may not be available depending on the
selected listening mode.
r This function cannot be used if headphones are
connected.
r This function cannot be used if "Height 1 Speakers
Type" is not set to "Front High".
„ Listening Mode: Select the listening mode from the
categories of "MOVIE/TV", "MUSIC", "GAME" and "THX".
r It cannot be set when audio is played from the TV's
speakers.
„ Video:
Monitor Out: The video input signals input to the unit
will be converted by the unit when they are output from
the HDMI OUT jack to the TV so that their resolution can
match that of the TV used. Select the HDMI OUT jack to
be used for output.
Control Monitor: Select the main room TV or the
separate room TV for which the CEC link function is
enabled when HDMI connection between the unit and
the separate room TV is established by Zone function.
r For details on Zone function, see the next section
"Using the multi-zone function".
Wide Mode: You can set the aspect ratio.
Picture Mode: You can adjust the image quality.
"Cinema" will automatically adjust the image to be
suitable to watch movie and "Game" suitable to play
game. In "Standard", the resolution will be changed but
the image quality will not be adjusted. In "Custom", "ISF
Day" and "ISF Night", you can adjust the brightness,
contrast, hue and saturation as desired. If you do not
adjust the resolution and image quality, select "Bypass".
r "Video" cannot be selected if the input is "NET", "USB" or
"BLUETOOTH".
„ Information:
Audio: Displays the audio input source, format, number of
channels, sampling frequency, listening mode, number of
output channels, and other audio information.
Video: Displays the video input source, resolution, signal
format, color tone, 3D information, Aspect, Picture Mode,
output, and other Video information.
Tuner: Displays the band, frequency, preset number, and
other tuner (radio) information.
15
Step 3: Playing Back
6
Using the multi-zone function
The function allows you to connect the unit with a TV or audio
equipment placed in a separate room so that you can enjoy audio
and video of the connected equipment even if you are staying in a
different room. It is possible to perform playback in the main room
and a separate room at the same time, for example by playing
the Blu-ray Disc player in the main room where the unit is placed
while playing Internet radio in a separate room. It is also possible to
perform playback only in a separate room. There are four methods
to configure multi-zone connection as described in "a" to "d" in the
right. Simultaneous playback in all zones is also possible.
the analog audio input jacks (¼) of the unit, the "NET", "USB" or
"BLUETOOTH" source, and the AM/FM broadcasting.
¼ When you connect a CD player or such other player without HDMI
output jack, connect it to the analog audio input jacks of the unit.
Multi-zone output is not possible if the connection is only with digital
optical cable or digital coaxial cable. In case of analog connection,
analog audio output setting may be necessary on the player.
r As for HDMI input and analog audio input, it is possible to play
the same source or different sources in the main room and
separate room.
r As for the "NET", "USB" and "BLUETOOTH", you cannot select
different audio sources for the main room and separate room.
For example, if "NET" has been selected in the main room and
then "USB" is selected as playback source in the separate room,
the input in the main room will change to "USB" accordingly.
r When listening to AM/FM broadcasting, you cannot select
different stations for the main room and separate room.
Therefore broadcasting of the same station will be heard in the
both rooms.
r If you play the same HDMI connected player for the main room
and a separate room, the sound field processing for 2 ch PCM
signals will be made in the main room.
Change the setting: Press RECEIVER and then HOME
on the remote controller, select "Setup" - "1.Input/Output
Assign" - "Monitor Out" - "Zone 2 Monitor Out" and set the
setting to "Use".
r You can view the information of the connected device on
the TV of Zone 2 by pressing DISPLAY during Zone 2
playback.
„ b. Connecting a TV in a separate room using
composite video cable
Video from the player without HDMI out jack can be
displayed on the TV in a separate room. First, connect
the player to composite video input jack of the unit. Then,
connect the TV in the separate room to ZONE 2 OUT V
jack of the unit using a composite video cable.
Outputting Video/Audio to a Separate Room
„ a. Connecting a TV in a separate room using
HDMI cable
You can play video and audio of the HDMI connected
player on the TV in a separate room. With an HDMI cable,
connect between the HDMI OUT ZONE 2 jack of the unit
and the HDMI IN jack of the TV in a separate room.
Main room
Zone 2
Zone 2
r It is not possible to output video from the player to the
TV in the separate room if the player is connected to the
HDMI IN jack or COMPONENT VIDEO IN jack.
r In this connection method, audio from the player cannot
be output from the TV. To output audio in the separate
room, see the next section "Listening to Music in a
Separate Room" and connect the unit to the integrated
amplifier or speakers located in the room where the TV is
placed.
Zone 3
z The sources from which you can enjoy the sound in a
separate room: For Zone 2, any can be selected from among
an external device connected to the HDMI input jack or the
analog audio input jacks (¼) of the unit, the "NET", "USB" or
"BLUETOOTH" source, and the AM/FM broadcasting. For Zone 3,
any can be selected from among an external device connected to
16
Zone 2
Step 3: Playing Back
To turn off the multi-zone function: Press ZONE on the
remote controller repeatedly to select Zone 2 or Zone 3.
Press zRECEIVER. To control on the main unit, press
ZONE2 or ZONE3 and within 8 seconds, press OFF.
Listening to Music in a Separate Room
„ c. Connecting an Integrated Amplifier in a
Separate Room
It is possible to play 2 ch source in a separate room while
11.2 ch source is being played in the main room. Connect
the PRE/LINE OUT ZONE 2 jacks or PRE/LINE OUT ZONE
3 jacks of the unit and the line-in jacks of the pre-main
amplifier in a separate room with an analog audio (RCA)
cable.
To adjust the volume: Press ZONE on the remote
controller a repeatedly to select Zone 2 or Zone 3. Adjust
the volume using VOL j/l. To do this on the main unit,
press ZONE2 or ZONE3, and adjust the volume using the
MASTER VOLUME control within 8 seconds.
To temporally mute the audio: Press ZONE on the remote
controller repeatedly to select Zone 2 or Zone 3. Then,
press MUTING to mute the audio.
Zone 2
Zone 3
Required setting: Press RECEIVER and then HOME on
the remote controller. Select "Setup" - "2. Speaker Setup" "Speaker Settings" and set "Powered Zone 2" or "Powered
Zone 3" to "Yes".
r Volume adjustment can be performed only from the unit.
Zone 2
Zone 3
r Volume can be adjusted with both the unit and the premain amplifier used in a separate room. To adjust it with
the unit, press RECEIVER and then HOME on the remote
controller, select "Setup" - "7. Hardware Setup" - "Multi
Zone" - "Zone 2 Out" or "Zone 3 Out" and set the setting
to "Variable". If you connect a power amplifier, be sure to
make the setting and adjust the volume in the main room.
„ d. Connecting Speakers in a Separate Room
It is possible to directly connect the speakers in another
room without an amplifier. Connect the speakers in the
separate room to ZONE2 or ZONE3 speaker terminals
of the unit using speaker cables. Note that 9.2 ch will be
the maximum in the main room during Zone 2 or Zone 3
playback. When both Zone 2 and Zone 3 playbacks are
performed at the same time, 7.2 ch will be the maximum in
the main room.
Performing Multi-zone Playback
1. Press ZONE on the remote controller a repeatedly to
select Zone 2 or Zone 3. Point the remote controller
at the unit and press zRECEIVER.
"Z2" or "Z3" lights on the main unit display and Zone
function is enabled.
r The Zone button stays lit red when Zone 2 is selected
and green when Zone 3 is selected.
2. Press INPUT SELECTOR of the input source to be
played in a separate room.
If you turn the unit to standby during multi-zone playback,
the Z2/Z3 indicators are dimmed and the playback
mode is switched to playback in a separate room only.
Performing steps 1 and 2 while the unit is in standby also
switches the playback mode to playback in a separate
room only.
To adjust the sound quality for the separate room: Press
ZONE2 on the main unit. Press TONE a few times to display
"Bass", "Treble" or "Balance" on the display. When the
desired item appears on the display, adjust the value with +
or - button.
r If "Zone 2 Out" is set to "Fixed", sound quality adjustment
are not effective.
r If Zone 2 or Zone 3 is on, power consumption during
standby becomes larger than normal.
r If Zone 2 or Zone 3 is turned on when the listening mode
of the main room is Pure Audio, it will automatically
switch to Direct.
r While Zone 2 or Zone 3 is on, the RI linked system function
(interlink between Onkyo components) is disabled.
WHOLE HOUSE MODE: If you press WHOLE
HOUSE MODE while playback is being performed in
the main room, the WHOLE HOUSE MODE is turned
on, "Z2" and "Z3" on the display light at the same
time and the playback sources of all the rooms are
switched to the same source at once.
r WHOLE HOUSE MODE is effective only for playback
of the external player connected to the analog audio
input jacks.
r This function cannot be used if headphones are
connected or audio is output from the speakers of
the TV.
To control on the main unit: Press ZONE2 or ZONE3 and
within 8 seconds, press the input selector button of the input to
be played in a separate room. To play the same source in the
main room and separate room, press ZONE2 or ZONE3 twice.
17
1
2
3
456
7
8
9
F
(European and
Asian models
G
H
I
J
K L
M
N O
PQ R S T
U
V
W
X
Front Panel
1 zON/STANDBY button: Turns the unit on or into
2
3
4
5
6
7
standby mode.
PURE AUDIO button and indicator: Switches to the
Pure Audio mode.
Remote control sensor: Receives signals from the
remote controller.
BLUETOOTH indicator: Flashes while pairing with a
Bluetooth-enabled device is in progress and stays lit
when pairing is completed.
Wi-Fi indicator: Stays lit while the unit is connected to
the wireless LAN router.
DOLBY ATMOS indicator: Stays lit when the Dolby
Atmos listening mode is selected with Height speakers
or surround back speakers enabled.
Input selector buttons: Switches the input to be
played.
18
8 Display
9 MASTER VOLUME control and indicator: Allows you
F
G
H
I
J
to adjust the volume.
HYBRID STANDBY indicator: Lights if the unit enters
standby mode when the HDMI Through, network
standby or Wakeup from Bluetooth function is enabled.
PHONES jack: Stereo headphones with a standard plug
are connected.
ZONE 2 button, ZONE 3 button and OFF button:
Controls the multi-zone function.
TONE and Tone Level buttons: Adjusts the high tone
and low tone.
MONITOR OUT button: Allows you to select the HDMI
jack to output the video input signals that are input to
the unit.
K DISPLAY button: Switches the information on the
display.
L QUICK SETUP button: Displays the Quick Setup menu.
M HOME button: Displays the Home menu.
N Cursor buttons, TUNINGl j button, PRESETd c
button and ENTER button: Moves the cursor and
confirms the selection. When listening to AM/FM
broadcasting, tune into the station with TUNINGl j or
select the registered station with PRESETd c.
O RETURN button: Returns the display to the previous
state.
P DIMMER button (North American models): Switches
Q
R
S
T
U
V
W
X
the brightness of the display.
RT/PTY/TP button (European and Asian models):
Can be used when receiving the station transmitting text
information.
MEMORY button: Registers or deletes a station.
TUNING MODE button: Switches the tuning mode.
USB port: A USB storage device is connected so that
music files stored in it can be played.
LISTENING MODE buttons: Allows you to select the
listening mode.
AUX INPUT HDMI/MHL jacks: An HD video camera or
MHL-enabled mobile device is connected. It is possible
to send video and audio of an MHL-enabled mobile
device.
AUX INPUT AUDIO/VIDEO, DIGITAL jacks: A video
camera or such other device is connected.
WHOLE HOUSE MODE button: Controls the WHOLE
HOUSE MODE function to play the same source in all
the multi-zone connected rooms.
SETUP MIC jack: The supplied speaker setup
microphone is connected.
Front flap
2.
1
8
2
3 4 5
9
6
F
7
G
Display
1 Speaker/Channel display: Displays the output channel
2
3
4
5
6
1.
7
that corresponds to the selected listening mode.
Z2/Z3: Lights when the output to Zone 2/Zone 3 is set to
on.
Lights according to the type of input digital signals and
the listening mode.
Stays lit when Music Optimizer is enabled.
Lights when NET or USB is controlled.
NET: Stays lit when the "NET" input is selected and the
unit is connected to the home network (LAN). It will flash
if the connection is not correct.
USB: Stays lit when the "USB" input is selected and a
USB storage device (e.g. USB memory) is connected. It
will flash if the connection is not correct.
HDMI: Stays lit when HDMI signals are input and the
HDMI input is selected.
DIGITAL: Stays lit when digital signals are input and the
digital input is selected.
MUTING: Flashes when MUTING on the remote
controller is pressed and audio is temporarily muted.
ANALOG: Stays lit when analog signals are input and
the analog input is selected. Or, it stays lit when HDMI
and digital signal inputs are not assigned.
SLEEP: Stays lit when the sleep timer is set.
Tuning indicators
RDS (European and Asian models): Stays lit when RDS
broadcasting is being received.
AUTO: Stays lit when the tuning mode is auto.
TUNED: c d flashes while tuning is automatically
performed. When tuned into a radio station, the
"c|670'&|d" on the display lights.
FM STEREO: Stays lit when an FM broadcasting is
being received.
8 Bi AMP: Stays lit when "Front Speakers Type" is set to
"Bi-Amp".
9 Stays lit when headphones are connected.
F Displays various information of the input signals.
Pressing DISPLAY displays the type of input digital
signals and the listening mode.
G Displays the volume level.
19
3
1 2
4
5
K L
J
6
7
M
89
F
4
N
G
H
I
O
P
Rear Panel
1 DIGITAL IN COAXIAL/OPTICAL jacks: Digital audio
signals are input.
2 RI REMOTE CONTROL jack: An Onkyo product with RI
jack can be connected and synchronized with this unit.
3 ETHERNET port: Used for LAN connection
4 Wireless antenna: Used for Wi-Fi connection or when
using a Bluetooth-enabled device. Adjust their angles
according to the connection status.
90°
180°
90°
180°
5 HDMI IN/OUT jacks: Digital video signals and audio
6
7
8
9
F
G
H
I
20
signals are transmitted between the unit and the
connected devices.
MONITOR OUT V jack: Video signals are output to the
connected monitor or TV.
COMPONENT VIDEO IN and OUT jacks: Component
video input/output jacks
ZONE 2 OUT V jack: Video signals of the player are
output to the connected TV in the separate room.
IR IN/OUT jack: Connected to the multiroom remote
control kit. (¼)
12V TRIGGER OUT ZONE2/ZONE3 jack: Allows you
to connect a device with trigger input jack in a separate
room to enable power link operation between the device
and the unit. (¼)
PC IN jack: PC is connected via an analog RGB cable.
AC INLET: The power cord is connected.
(/#06'00#LCEM
ŝCPF#/#06'00#
terminal: The supplied antennas are connected.
J RS232 port: Connected to the home control system. (¼)
K GND terminal: The ground wire of the turntable is
connected.
L Composite video and analog audio jacks: Analog
video signals and audio signals are input.
M PRE OUT jacks: A power amplifier or subwoofer with
built-in amplifier is connected.
N PRE/LINE OUT ZONE 2 and PRE/LINE OUT ZONE
3 jacks: Audio output jacks connected to the pre-main
amplifier for multi-zone playback in a separate room.
O SPEAKERS terminals: Speakers are connected. To
use the Multi-zone function, connect the speakers in the
separate room to the ZONE2 speaker terminals.
P PRE OUT BALANCE jacks: An amplifier with balancetype XLR input jacks is connected.
¼
Special devices or cable connections are necessary to use the
control functions 9, F and J. Contact the specialized stores for
more information.
Troubleshooting
Before starting the procedure
Problems may be solved by simply turning the power
on/off or disconnecting/connecting the power cord,
which is easier than working on the connection,
setting and operating procedure. Try the simple
measures on both the unit and the connected
device. If the problem is that the video or audio is not
output or the HDMI linked operation does not work,
disconnecting/connecting the HDMI cable may solve
it. When reconnecting, be careful not to wind the
HDMI cable since if wound the HDMI cable may not fit
well. After reconnecting, turn off and on the unit and
the connected device.
HDMI control does not function correctly.
r Set the CEC link function of the unit to on. It is also
necessary to make the HDMI linked system setting on
the TV. See the TV's instruction manual for details.
The remote controller does not work.
r Be sure to press RECEIVER first before operating the
unit with the remote controller.
There is no sound for multi-zone function.
r The AV receiver will automatically enter standby mode
when Auto Standby is set and launched.
r When you connect a CD player or such other player
without HDMI output jack, connect it to the analog audio
input jacks of the unit. Multi-zone output is not possible if
the connection is only with digital optical cable or digital
coaxial cable. In case of analog connection, analog audio
output setting may be necessary on the player.
There’s no sound, or it’s very quiet.
Cannot access to network.
r A wrong input selector button has been selected. Select
a correct input for the player. Also check that muting is
not on.
r Not all listening modes use all speakers.
r Try plugging/unplugging the unit or the wireless LAN
router or check their power-on status. This will work well
in many cases.
r If the desired wireless LAN router is not in the access
point list, it may be set to hide SSID or the ANY
connection may be off. Change the setting and try again.
The AV receiver turns off unexpectedly.
There’s no picture.
r A wrong input selector button has been selected.
r Video is not displayed if the listening mode is Pure Audio.
r To display video from the connected player on the TV
screen while the unit is in standby, you need to enable
HDMI Through function.
r When the TV image is blurry or unclear, power cord or
connection cables of the unit may have interfered. In
that case, keep distance between TV antenna cable and
cables of the unit.
r If you connect a player supporting HDCP2.2, be sure to
connect it to the HDMI IN3 jack of the unit. At the time,
connect the TV to the HDMI OUT MAIN jack.
Bluetooth
r Try plugging/unplugging the unit and the Bluetoothenabled player. After that, check that the Bluetooth
function is enabled on the Bluetooth-enabled device and
the connection with the unit has been established.
„ Resetting the unit
Resetting the unit to the status at the time of shipment may
solve the problem. If the measures above do not solve the
problem, reset the unit with the following procedure. If you
reset the unit status, your preferences will be reset to the
defaults. Note them down before starting reset.
z How to reset:
1. While holding down CBL/SAT on the main unit (note
that step 2 must be performed with this button
pressed down)
2. Press zON/STANDBY on the main unit ("Clear"
appears on the display and the unit returns to standby)
Clear
2. Press zON/STANDBY
holding down
1. While
CBL/SAT,
z How to reset the remote controller:
1. While holding down RECEIVER on the remote
controller, press HOME (about 3 seconds) until
RECEIVER lights.
2. Within 30 seconds, press RECEIVER again.
NET
TUNER
USB
BLUETOOTH
RECEIVER
MUTING
REMOTE MODE
MODE
TV
RECEIVER
CH
DISC
TV
VOL
VOL
ALBUM
INPUT
TOP MENU
MENU
GUIDE
PLAYLIST
PREV CH
ENTER
PLAYLIST
Q
SETUP
HOME
RETURN
HOME
21
Specifications
Amplifier Section
Network Section
Rated Output Power
All channels: 135 watts minimum continuous power per channel, 8
ohm loads, 2 channels driven from 20 Hz to 20 kHz, with a maximum
total harmonic distortion of 0.08% (FTC)
(North American)
11 ch × 185 W at 6 ohms, 1 kHz, 1 ch driven of 1% (IEC) (Others)
Maximum Effective Output Power
11 ch × 230 W at 6 ohms, 1 kHz, 1 ch driven (JEITA) (Asian)
Dynamic Power (¼)
¼
IEC60268-Short-term maximum output power
9
ŝ(TQPV
9
ŝ(TQPV
9
ŝ(TQPV
THD+N (Total Harmonic Distortion+Noise)
0.08% (20 Hz - 20 kHz, half power)
Damping Factor
(TQPVM*\ŝ
Input Sensitivity and Impedance (Unbalance)
O8Mŝ
.+0'
O8Mŝ
2*101//
Rated RCA Output Level and Impedance
O8ŝ
24'176
Maximum RCA Output Level and Impedance
8ŝ
24'176
Rated XLR Output Level and Impedance
O8ŝ
24'176
Maximum XLR Output Level and Impedance
8ŝ
24'176
Phono Overload
70 mV (MM 1 kHz 0.5% Direct)
Frequency Response
5 Hz - 100 kHz/+1 dB, –3 dB (Direct mode)
Tone Control Characteristics
±10 dB, 50 Hz (BASS)
±10 dB, 20 kHz (TREBLE)
Signal to Noise Ratio
110 dB (LINE, IHF-A)
80 dB (PHONO MM, IHF-A)
Speaker Impedance
ŝŝQTŝŝ
Ethernet LAN
10BASE-T/100BASE-TX
Wireless LAN
IEEE 802.11 b/g/n standard
(Wi-Fi® standard)
2.4 GHz band: 1 - 11 ch (North American)
10 - 11 ch (Spain)
10 - 13 ch (France)
1 - 13 ch (Others)
(Wi-Fi® standard)
Video Section
Input Sensitivity/Output Level and Impedance
8RRŝ
%QORQPGPV;
8RRŝ
%QORQPGPV2B/CB, PR/CR)
8RRŝ
%QORQUKVG
Component Video Frequency Response
5 Hz - 100 MHz/+0 dB, –3 dB
Tuner Section
FM Tuning Frequency Range
87.5 MHz - 107.9 MHz (North American)
87.5 MHz - 108.0 MHz, RDS (Others)
AM Tuning Frequency Range
522/530 kHz - 1611/1710 kHz
Preset Channel
40
22
Bluetooth Section
Communication system
Bluetooth Specification version 2.1 +EDR (Enhanced Data Rate)
Maximum communication range
Line of sight approx. 15 m (¼)
Frequency band
2.4 GHz band (2.4000 GHz - 2.4835 GHz)
Modulation method
FHSS (Freq Hopping Spread Spectrum)
Compatible Bluetooth profiles
A2DP 1.2 (Advanced Audio Distribution Profile)
AVRCP 1.3 (Audio Video Remote Control Profile)
Supported Codecs
SBC
Transmission range (A2DP)
20 Hz - 20,000 Hz (Sampling frequency 44.1 kHz)
¼
The actual range will vary depending on factors such as obstacles
between devices, magnetic fields around a microwave oven, static
electricity, cordless phone, reception sensitivity, antenna’s performance,
operating system, software application, etc.
General
Power Supply
AC 120 V, 60 Hz (North American)
AC 220 - 240 V, 50/60 Hz (Others)
Power Consumption
10.7 A (North American)
1105 W (Others)
0.1 W (Stand-by, North American)
0.13 W (Stand-by, Others)
145 W (No-sound, North American)
155 W (No-sound, Others)
Dimensions (W × H × D)
435 mm × 199 mm × 466.5 mm
17-1/8" × 7-13/16" × 18-3/8"
Weight
22 kg (48.5 lbs.)
z HDMI
Input
IN1 (BD/DVD), IN2 (CBL/SAT), IN3 (STB/DVR, HDCP2.2), IN4 (GAME),
IN5 (PC), IN6, IN7, AUX INPUT (HDMI/MHL) (front)
Output
OUT MAIN (ARC, HDCP2.2), OUT SUB, OUT ZONE2
Video Resolution
Pass through: 4K 60Hz (YCbCr 4:2:0)
Upscaling: 4K 30Hz
Audio Format
Dolby Atmos, DTS-HD Master Audio, DTS-HD High Resolution Audio,
Dolby TrueHD, Dolby Digital Plus, DSD, Multichannel PCM
Supported
3D, Audio Return Channel, DeepColor, x.v.Color, LipSync, CEC (RIHD),
4K (Upscaling and Passthrough)
z Video Inputs
Component
IN1 (BD/DVD), IN2 (CBL/SAT)
Composite
IN1 (CBL/SAT), IN2 (STB/DVR), IN3 (GAME), AUX INPUT (front)
Analog RGB inputs
PC IN
z Video Outputs
Component
MONITOR OUT
Composite
MONITOR OUT, ZONE2 OUT
z Audio Inputs
Digital
OPTICAL 1 (GAME), 2 (TV/CD), AUX INPUT DIGITAL (front)
COAXIAL 1 (BD/DVD), 2 (CBL/SAT), 3 (STB/DVR)
Analog
BD/DVD, CBL/SAT, STB/DVR, GAME, PC, TV/CD, PHONO, AUX INPUT
(front)
z Audio Outputs
Analog
PRE/LINE OUT ZONE2, ZONE3
Balance Pre Outputs
PREOUT FRONT L, FRONT R
Analog Multichannel Pre Outputs
FRONT L/R, CENTER, SURROUND L/R, BACK L/R,
HEIGHT 1 L/R, HEIGHT 2 or WIDE L/R, SW1 x 2, SW2 x 2
Speaker Outputs
FRONT L/R, CENTER, SURR L/R, BACK L/R, HEIGHT 1 (or ZONE3 or
Bi-AMP) L/R, HEIGHT 2/WIDE (or ZONE2) L/R
Phones
PHONES (Front, ø 6.3)
z Others
Setup Mic 1 (Front)
RS232 1
Ethernet 1
IR IN 1/OUT 1
12V TRIGGER OUT 2 (ZONE2/ZONE3)
USB 1 (Front)
RI 1
Specifications and features are subject to change without notice.
License and Trademark Information
DISCLAIMER
Manufactured under license from Dolby Laboratories. Dolby, Dolby Atmos,
Dolby Surround, Surround EX and the double-D symbol are trademarks of
Dolby Laboratories.
For DTS patents, see http://patents.dts.com. Manufactured under license from
DTS Licensing Limited. DTS, DTS-HD, the Symbol, & DTS and the Symbol
together are registered trademarks, and DTS-HD Master Audio and DTS Neo:X
| 11.1 are trademarks of DTS, Inc. © DTS, Inc. All Rights Reserved.
Qdeo and QuietVideo are trademarks of Marvell or its affiliates.
The Wi-Fi CERTIFIED® Logo is a certification mark of the Wi-Fi Alliance.
Wi-Fi certified® logo shows international association certifying interoperability
“Wi-Fi alliance” ensures the product has passed the test for compatibility with
other Wi-Fi certified equipment.
The Bluetooth® word mark and logos are registered trademarks owned by
Bluetooth SIG, Inc. and any use of such marks by Onkyo is under license.
Other trademarks and trade names are those of their respective owners.
Onkyo does not guarantee Bluetooth compatibility between the AV receiver and
all Bluetooth-enabled devices.
For compatibility between the AV receiver and another device with Bluetooth
technology, consult the device’s documentation and dealer. In some countries,
there may be restrictions on using Bluetooth devices. Check with your local
authorities.
Re-Equalization and the “Re-EQ” logo are trademarks of THX Ltd.
Manufactured under license from THX Ltd. THX and the THX logo are
registered in the U.S. and other jurisdictions. All rights reserved. Surround EX is
a trademark of Dolby Laboratories. Used with permission.
U.S. Pat. nos. 7,254,239 & 7,593,533 & 7,974,425 & 8,452,028 & 8,509,457
Taiwan Pat. I238671 European Pat. 1,360,874
THX Select2 Plus
Before any home theater component can be THX Select2 Plus certified, it
must pass a rigorous series of quality and performance tests. Only then can
a product feature the THX Select2 Plus logo, which is your guarantee that
the Home Theater products you purchase will give you superb performance
for many years to come. THX Select2 Plus requirements define hundreds of
parameters, including power amplifier performance, and pre-amplifier
performance and operation for both digital and analog domains. THX Select2
Plus receivers also feature
proprietary THX technologies (e.g., THX Mode) which accurately translate
movie soundtracks for home theater
playback.
AccuEQ, Music Optimizer, RIHD and WRAT are trademarks of Onkyo
Corporation.
“RIHD” and “RIHD (logo)” are trademarks of Onkyo Corporation.
®
The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI
Logo are trademarks or registered trademarks of HDMI Licensing LLC in the
United States and other countries.
“MHL, the MHL Logo, and Mobile High-Definition Link are trademarks or
registered trademarks of MHL LLC in the United States and other counties.”
InstaPrevue and the InstaPrevue logo are trademarks or registered trademarks
of Silicon Image, Inc. in the United States and other countries.
Apple, iPod and iPhone are trademarks of Apple Inc., registered in the U.S. and
other countries.
Apple TV is a trademark of Apple Inc., registered in the U.S. and other
countries.
SIRIUS, XM and all related marks and logos are trademarks of Sirius XM Radio
Inc. and its subsidiaries. All rights reserved.
DLNA®, the DLNA Logo and DLNA CERTIFIED® are trademarks, service
marks, or certification marks of the Digital Living Network Alliance.
This product is protected by certain intellectual property rights of Microsoft. Use
or distribution of such technology outside of this product is prohibited without a
license from Microsoft.
Through this device you are able to link to other services or websites which
are not under the control of any company which has designed, manufactured
or distributed/have distributed this device, and its affiliates (collectively,
“Company”). We have no control over the nature, content and availability
of those services. The inclusion of any links does not necessarily imply a
recommendation or endorse the views expressed within them.
All information, content and services available through this device belong to
third parties and are protected by copyright, patent, trademark and/or other
intellectual property laws of applicable countries.
The information, content and services provided through this device are for your
personal, noncommercial use only. Any information, content or services may
not be used in any manner other than previously approved by the appropriate
content owner or service provider.
You may not modify, copy, republish, translate, exploit, create derivative works,
upload, post, transmit, sell or distribute in any manner any information, content
or services available through this device, unless expressly permitted by the
appropriate copyright, patent, trademark and/or other intellectual property
owner, including, without limitation, content owner or service provider.
THE CONTENT AND SERVICES AVAILABLE THROUGH THIS DEVICE ARE
PROVIDED “AS IS”.
COMPANY DOES NOT WARRANT INFORMATION, CONTENT OR
SERVICES SO PROVIDED, EITHER EXPRESSLY OR IMPLIEDLY, FOR ANY
PURPOSE.
COMPANY EXPRESSLY DISCLAIMS ANY WARRANTIES, EXPRESS
OR IMPLIED, INCLUDING BUT NOT LIMITED TO, WARRANTIES OF
TITLE, NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE.
Company makes no representation or warranty of any kind, express or implied,
about the completeness, accuracy, validity, legality, reliability, suitability or
availability with respect to the information, content or services available through
this device. Company shall not be liable, whether in contract or tort, including
negligence and strict liability, for any direct, indirect, special, incidental or
consequential damages or any other damages arising out of, or in connection
with, any information contained in, or as a result of the use of any content or
service by you or any third party, even if Company has been advised of the
possibility of such damages, nor shall Company be liable for any third party
claims against users of this device or any third party.
In no event shall Company be responsible nor liable for, without limiting the
generality of the foregoing, any interruption or suspension of any information,
content or service available through this device. Company is neither responsible
nor liable for customer service related to the information, content and services
available through this device. Any question or request for service relating to
the information, content or services should be made directly to the appropriate
content owners and services providers.
Windows and the Windows logo are trademarks of the Microsoft group of
companies.
QR Code is a registered trademark of DENSO WAVE INCORPORATED.
Safari is a trademark or registered trademark of Apple Computer, Inc. in the
United States.
“x.v.Color” is a trademark of Sony Corporation.
MPEG Layer-3 audio coding technology licensed from Fraunhofer IIS and
Thomson.
“Xantech” is a registered trademark of Xantech Corporation.
“Niles” is a registered trademark of Niles Audio Corporation.
“All other trademarks are the property of their respective owners.”
23
Precautions
–
For European Models
–
Declaration of Conformity
We declare, under our sole responsibility, that
this product complies with the standards:
– Safety
– Limits and methods of measurement of
radio disturbance characteristics
– Limits for harmonic current emissions
– Limitation of voltage changes, voltage
fluctuations and flicker
– RoHS Directive, 2011/65/EU
– Hereby, Onkyo Corporation, declares that
this TX-NR3030 is in compliance with the essential requirements and other
relevant provisions of Directive 1999/5/EC.
– µÑÄÕÖÒãÝÉÖÒ2QN\R&RUSRUDWLRQÈÉÎÏÄÔÌÔÄÛÉ7;15ÉÆ
ÕÞÒÖÆÉÖÕÖÆÌÉÕÞÕÕÞÝÉÕÖÆÉÑÌÖÉÌËÌÕÎÆÄÑÌãÌÈÔ×ÇÌÖÉÓÔÌÏÒÊÌÐÌ
ÔÄËÓÒÔÉÈÅÌÑĨÌÔÉÎÖÌÆÄ(&
– 1PM[Q%QTRQTCVKQPVÉOVQRTQJNCwWLGzG6:04URNĢWLG\½MNCFPÉ
RQzCFCXM[CXwGEJPCRįÉUNWwP½WUVCPQXGPK5OøTPKEG'5
– Undertegnede Onkyo Corporation erklærer herved, at følgende udstyr TXNR3030 overholder de væsentlige krav og øvrige relevante krav i direktiv
1999/5/EF.
– Hiermit erklärt Onkyo Corporation, dass sich das Gerät TX-NR3030 in
Übereinstimmung mit den grundlegenden Anforderungen und den übrigen
einschlägigen Bestimmungen der Richtlinie 1999/5/EG befindet.
–
–
–
–
–
–
–
–
–
Käesolevaga kinnitab Onkyo Corporation seadme TX-NR3030 vastavust
direktiivi 1999/5/EÜ põhinõuetele ja nimetatud direktiivist tulenevatele
teistele asjakohastele sätetele.
ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ Ο ΚΑΤΑΣΚΕΥΑΣΤΗΣ Onkyo Corporation ΔΗΛΩΝΕΙ
ΟΤΙ TX-NR3030 ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ
ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕΚ
Por la presente, Onkyo Corporation, declara que este TX-NR3030 cumple
con los requisitos esenciales y otras exigencias relevantes de la Directiva
1999/5/EC.
Par la présente, Onkyo Corporation déclare que l’appareil TX-NR3030 est
conforme aux exigences essentielles et aux autres dispositions pertinentes
de la directive 1999/5/CE.
Con la presente Onkyo Corporation dichiara che questo TX-NR3030 è
conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite
dalla direttiva 1999/5/CE.
#TwQ1PM[Q%QTRQTCVKQPFGMNCTðMC6:04CVDKNUV&KTGMVĈXCU
'-DĿVKUMCLÞORTCUĈDÞOWPEKVKGOCTVQUCKUVĈVCLKGOPQVGKMWOKGO
Šiuo Onkyo Corporation deklaruoja, kad šis TX-NR3030 atitinka esminius
reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas.
A Onkyo Corporation ezzennel kijelenti, hogy a TX-NR3030 típusú berenFG\ÅUVGNLGUÉVKC\CNCRXGVĩMÒXGVGNOÅP[GMGVÅUO½U'-KT½P[GNXDGP
OGIJCV½TQ\QVVXQPCVMQ\ÏTGPFGNMG\ÅUGMGV
Hierbij verklaart Onkyo Corporation dat het toestel l TX-NR3030 in
overeenstemming is met de essentiële eisen en de andere relevante
bepalingen van richtlijn 1999/5/EG.
0KPKGLU\[O1PM[Q%QTRQTCVKQPFGMNCTWLGŏG6:04LGUV\IQFP[
\\CUCFPKE\[OKY[OCICPKCOKKKPP[OKYĜCıEKY[OKRQUVCPQYKGPKCOK
Dyrektywy 1999/5/EC.
Eu, Onkyo Corporation, declaro que o TX-NR3030 cumpre os requisitos
essenciais e outras provisões relevantes da Directiva 1999/5/EC.
The Americas
18 Park Way, Upper Saddle River, N.J. 07458, U.S.A.
For Dealer, Service, Order and all other Business Inquiries:
Tel: 201-785-2600 Fax: 201-785-2650
http://www.us.onkyo.com/
For Product Support Team Only:
1-800-229-1687
–
–
–
–
–
–
–
2TKPRTG\GPVC1PM[Q%QTRQTCVKQPFGENCTàEàCRCTCVWN6:04GUVG
ÊPEQPHQTOKVCVGEWEGTKPķGNGGUGPķKCNGĵKEWCNVGRTGXGFGTKRGTVKPGPVGCNG
Directivei 1999/5/CE.
1PM[Q%QTRQTCVKQPVÙOVQX[JNCUWLGzG6:04CURĔĢC\½MNCFPÅ
RQzKCFCXM[CXwGVM[RTÉUNWwPÅWUVCPQXGPKC5OGTPKEG'5
Onkyo Corporation izjavlja, da je ta TX-NR3030 v skladu z bistvenimi
\CJVGXCOKKPFTWIKOKTGNGXCPVPKOKFQNQêKNKFKTGMVKXG'5
Onkyo Corporation vakuuttaa täten että TX-NR3030 tyyppinen laite on
direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin
muiden ehtojen mukainen.
*ÀTOGFHÒTMNCTCT1PM[Q%QTRQTCVKQPCVVFGPPC6:04HÒNLGTFG
väsentliga kraven och andra relevanta stadgar i Direktiv 1999/5/EC.
Hér með lýsir Onkyo Corporation því yfir að varan TX-NR3030 er í
UCOTÂOKXKÌITWPPMTÒHWTQICÌTCTMTÒHWTUGOIGTÌCTGTWÉVKNUMKRWP
EC.
Onkyo Corporation erklærer herved at denne TX-NR3030 er i
overensstemmelse med vesentlige krav og andre relevante bestemmelser i
direktiv 1999/5/EC.
1XKOG1PM[Q%QTRQTCVKQPRQVXTîWLGFCLG6:04WUWINCUPQUVKUC
osnovnim zahtjevima i ostalim relevantnim odredbama Direktive 1999/5/EC.
(Mainland)
Europe
Kitahama Chuo Bldg, 2-2-22 Kitahama, Chuo-ku,
OSAKA 541-0041, JAPAN
http://www.onkyo.com/
–
Liegnitzerstrasse 6, 82194 Groebenzell, GERMANY
Tel: +49-8142-4401-0 Fax: +49-8142-4208-213
http://www.eu.onkyo.com/
1301, 555 Tower, No.555 West NanJing Road, Jing’an District,
Shanghai, China 200041,
Tel: 86-21-52131366 Fax: 86-21-52130396
http://www.cn.onkyo.com/
Meridien House, Ground floor, 69 - 71 Clarendon Road,
Watford, Hertfordshire, WD17 1DS, United Kingdom
Tel: +44 (0)8712-00-19-96 Fax: +44 (0)8712-00-19-95
Asia, Oceania, Middle East, Africa
Please contact an Onkyo distributor referring to Onkyo
SUPPORT site.
http://www.intl.onkyo.com/support/
China
(Hong Kong)
Unit 1033, 10/F, Star House, No 3, Salisbury Road,
Tsim Sha Tsui Kowloon, Hong Kong.
Tel: 852-2429-3118 Fax: 852-2428-9039
http://www.hk.onkyo.com/
The above-mentioned information is subject to change
without prior notice.
Visit the Onkyo web site for the latest update.
D1406-0
SN 29401675
(C) Copyright 2014 Onkyo Corporation Japan. All rights reserved.
* 2 9 4 0 1 6 7 5 *
">