advertisement
input tv cbl dvd aux menu
A B setup
C D
Universal Remote
Instruction Manual
Control Remoto Universal
Manual de Instrucciones
11695
input tv cbl dvd aux menu
A B setup
C D input tv cbl dvd aux menu
A B C setup
D list exit list exit list exit
7252
Table of Contents
Introduction ..................................................................................... 2
Setup .................................................................................................. 3
Button Functions .......................................................................... 4
Programming Your Remote ..................................................... 6
Direct Code Entry................................................................... 6
Auto Code Search ................................................................. 8
Controlling Combo Devices .............................................. 9
Using Your Remote ....................................................................10
Master Volume Feature ....................................................10
Reset to Factory Settings .................................................11
Troubleshooting ..........................................................................12
Warranty ........................................................................................13
FCC Statement .............................................................................14
Introduction
Congratulations on your purchase of the GE Universal
Remote. This remote is capable of operating thousands of audio/video devices including TVs, DVD players, cable, satellite receivers and more!
IMPORTANT: SAVE THIS MANUAL AND CODE LIST
FOR FUTURE REFERENCE
Scan this to view remote setup video
Mira a ver el video de instalación remota http://www.jascoproducts.com/remote
2
Setup
Your universal remote requires two (2) AAA batteries
(not included). Alkaline batteries are recommended.
Battery Installation
1. On the back of the remote, pull back on the tab and lift the cover off.
2. Match the (+) and (-) marks on the batteries to the
(+) and (-) marks inside the battery compartment, then insert two (2) AAA batteries. Be sure to use fresh batteries.
3. Press the battery cover back into place.
NOTE: If your remote stops operating properly, replace the batteries with new ones. The remote will retain the codes you have programmed for up to 10 minutes after the batteries are removed.
Battery Precautions
• Do not mix old and new batteries.
• Do not mix alkaline, standard (carbon-zinc), or rechargeable (Ni-Cd, Ni-MH, etc.) batteries.
• Always remove old, weak or worn-out batteries promptly and recycle or dispose of them in accordance with local and national regulations.
• Remove batteries if product is to be unused for an extended period of time.
Battery Saver
Your remote automatically turns off if the buttons are depressed more than 8 seconds. This will save your batteries should your remote get stuck in a place where the buttons remain depressed (e.g., between the sofa cushions).
Code Saver
You will have up to 10 minutes to change the batteries in your remote without losing codes you have programmed. However, do not press any buttons until batteries are installed in the remote. If buttons are pressed without batteries in the remote, all codes will be lost.
3
input tv cbl dvd aux menu
A B setup
C D list exit
Button Functions
tv cbl menu
A B
TV, CBL, DVD,
AUX
Selects device to control.
input
REW (rewind), FF (fast
dvd aux
Control buttons that operate your DVR even when the remote is set
setup
operates DVD Scan -/+.
C D
Menu on the TV.
A, B, C, D Uses
A, B, C, D functions on supported devices
list
UP, DOWN, LEFT &
RIGHT Navigation
buttons.
exit
VOLUME UP/DOWN
Changes the volume level of the device, normally the TV.
MUTE Turns off the
TV sound while the picture remains.
DOT (•) Used
to select digital channels, e.g., 2.3.
list input tv cbl dvd aux menu
A B C setup
D exit
4
input tv cbl dvd aux menu
A B setup
C D list exit input tv cbl dvd aux menu
A B setup
C D list exit
Button Functions, cont.
ON•OFF
Turns
devices On or Off.
tv cbl dvd aux menu list
A B C input setup
D exit
INPUT Selects the video
inputs from available viewing sources.
GUIDE Displays
satellite or cable on-screen program guide.
SETUP Used to
setup the remote, and for code search function.
INFO Displays/selects
on-screen channel information.
OK Selects menu
items for the device you are controlling.
EXIT Exits On-Screen
Menus.
CHANNEL UP/
DOWN Changes
the channels.
Also controls DVD
CHAPTER +/- track selection,
(Prev. Ch) Returns
to the previously selected channel.
NUMBERS
Enter numbers for direct channel selection. Some devices require
ENTER to be pressed
after channel selection.
5
Programming Your Remote
menu list tv cbl dvd aux
A B C input setup
D tv cbl dvd aux menu
B C tv cbl menu setup list
D
B input dvd aux setup
C D tv input cbl dvd aux menu
A B setup
C D tv cbl dvd menu tv cbl dvd input aux input
A aux
A
B C D menu list
B exit list setup
C D tv cbl exit
Your GE universal remote control is designed to control multiple audio/video devices such as a TV,
DVD, DVR, satellite, cable and audio device using only one remote. To use this remote, you will need to program it to control the devices of your choice. There are two ways to program the remote - direct code entry or auto code search.
Direct Code Entry (Recommended)
dvd tv menu list
A input aux
1. Locate the Remote Code List provided.
Find the
DEVICE CATEGORY you wish
to program (for example
TV, CBL, DVD,
AUX) and then find the BRAND of that
device. Circle all the codes under that brand. Example: For a GE TV, locate the
TV code section then circle all of the
GE TV codes.
2. Manually turn on the device you wish to control.
setup cbl dvd input aux
3. Press and hold the
SETUP button
until the red indicator light stays on
(approximately 2 seconds) and then release the
SETUP button.
D
B C setup
D
4. Press and release the device button on the remote (
TV, CBL, DVD, AUX). The
tv cbl
remain on.
exit
5. Enter the first 4-digit code previously found in the code list using the
menu
code entered is a valid code, the red
B C D
entered is not a valid code, the red indicator light will flash and remain on allowing you to re-enter the code.
Note: If no buttons are pressed for 35 seconds, the remote will exit the SETUP mode and you will have to start over.
list exit list exit list
6. Point the remote at the device. Press
exit
6
input tv cbl dvd aux menu
A B setup
C D list exit input tv cbl dvd aux menu
A B setup
C D list exit
Programming Your Remote, cont.
the
POWER button—if the device
turns off, no further programming is required for that device. If the device and use the next code found in the
tv cbl
code for your device is found.
7. Repeat this process for each device
(for example TV, DVD, CBL, SAT, DVR,
menu
A
system you wish to control.
B C D
Programming Notes
• If your device does not respond to the remote after trying all codes listed or your brand is not listed in the code list, use the Auto Code Search method to program your remote.
• Sometimes the first code that “works” with your device may operate only a few functions of your device. There may be another code in the code list that performs more functions. Try other codes from the code list for more functionality.
• With the Direct Code Entry method, you can program any device button to control any device in your home entertainment system.
For example, you can use the
AUX device button
to control an audio receiver or a DVD, VCR, satellite device, etc.
• For combination devices, you may have to enter a code for each device. For example, for a VCR/DVD device, you may have to enter a code for the DVD under the
DVD button and enter a code for the
VCR using a different device button on the remote.
• Write down the code found to operate your device for future reference.
7
Programming Your Remote, cont.
tv cbl dvd tv cbl aux tv cbl dvd aux input tv cbl dvd menu list
A B menu
C D
A tv
B
B menu list
A B tv cbl list menu list list
A B
C D setup
A
C D setup
C D dvd exit
C input setup
D exit exit
B dvd tv cbl aux tv cbl menu
C D
A tv
B
B menu list
A B tv cbl list menu list list
A B dvd dvd
C D
C input aux input menu setup input
D tv cbl
A
Auto Code Search
The Auto Code Search, searches automatically through all of the codes stored in this remote. Read all the steps prior to starting the auto code search as you will need to be prepared to lock-in the proper code when found.
dvd aux input
1. Manually turn on the device you wish
B C tv cbl
A
2. Press and hold the
SETUP button
B C D menu
A
D tv
release the button.
3. Press and release the device button
B C D
TV, CBL, DVD, AUX) the
C dvd
C setup
D exit setup
D exit exit
red indicator will blink once and then remain on.
menu list
A
4. Point the remote at the device and press and release the
POWER button
B C tv cbl
D
PLAY button (for DVD, VCR,
etc.) to start the search. The red
list menu list list
A
every 2 seconds) as the remote searches.
Note: The remote must be pointed at the device for the duration of this search.
B C
D
#1 button so
you are prepared to lock-in the code.
6. When the device shuts off or begins playing, press the
#1 button to lock-in
the code. The red indicator light will turn off.
Note: You have approximately two seconds after the device shuts off
or begins playing to lock-in the code.
7. Point the remote at the device and check to see if the remote operates the device as desired. If it does, no further programming is required for that device. If it does not, return to step 2 and start the auto code search again.
8
Programming Your Remote, cont.
8. Repeat this process for each device (for example
TV, DVD, SAT, AUX) in your home entertainment system you wish to control.
Programming Notes
• This process may take several minutes as the remote contains many codes.
• When using the Auto Code Search programming method, the device button corresponding to the type of device you want to control must be selected (for example, the
TV device button must
be selected in step 3 if you want to control a TV, the
DVD device button for a DVD player, etc.)
• The
SETUP button can be used during the search
process to reverse the direction of the search of the remote codes. For example, if you miss the code for your device and the remote is continuing to search (as indicated by the blinking red light), press the
SETUP button and the code search will
reverse direction and return to the code.
• Sometimes the first code that “works” with your device may operate only a few functions of your device. There may be another code in the code list that performs more functions. Continue the auto code search as directed above until the best code is found.
Controlling Combo Devices
Some Combo devices (e.g. TV/VCR, TV/DVD, DVD/
VCR, etc.) will require you to set up two different Mode buttons to control both parts of the Combo device.
For example, if you have a TV/DVD Combo, you might need to set up one code under the
TV button to control the TV part AND a separate code (under any other Mode button) to control the DVD part.
9
input input tv cbl dvd aux input tv cbl dvd aux input tv
Master Volume Feature
input menu
A menu
A
B
B menu tv cbl
A tv cbl list dvd
B tv cbl dvd setup input
A setup dvd input
C D aux
C D
C D
B C exit aux tv cbl
A
D menu
A tv cbl
A
B
B menu list dvd
C
B tv cbl dvd setup input
A setup dvd input
C D aux
D
C D
B C exit aux setup menu tv cbl
A
The Master Volume Feature allows you to select a single device (TV or audio receiver) that the volume control always controls. For example, the remote can volume on your audio receiver instead of your TV.
dvd
D
Enabling the Master Volume Feature
D menu
A
A
B C tv cbl list dvd
B C
A setup input
D aux
D
B C D
SETUP button
until the red indicator stays on
(approximately 2 seconds) and then release the button.
2. Press and release desired device button (
TV, CBL, DVD, AUX) for the
device you wish to setup to always control the volume.
3. Press and release the
MUTE button.
4. Press and release the
VOL + button.
The red indicator will blink twice and then go off.
list list exit exit input list list exit exit input list list exit exit input
To test the feature put the remote in another mode such as the TV mode if you programmed the audio receiver to be the Master Volume Device. Point the remote at the audio receiver, press and hold either the
VOL - or the VOL + button.
If the audio receiver volume changes then the remote is programmed correctly. If the TV volume changes and not the audio receiver, you will have to repeat the steps above and test again.
tv cbl dvd aux tv cbl dvd aux tv cbl dvd aux menu
A B tv cbl
C D dvd setup input aux menu
A B tv cbl dvd setup input
C D aux menu
A B C tv cbl dvd setup input
D aux
Disabling the Master Volume Feature
1. Press and hold the
SETUP button
until the red indicator stays on
(approximately 2 seconds) and then release the button.
2. Press and release the device button (
TV, CBL, DVD, AUX) which is
programmed to control the Master
Volume Feature.
10
menu setup menu setup menu setup
A list
B C D exit
A list
B C D exit
A list
B C D exit list exit list exit list exit
input input tv cbl dvd tv cbl aux dvd aux input input tv cbl dvd tv cbl aux dvd aux input input tv cbl dvd tv cbl aux dvd aux tv cbl menu dvd aux menu
A B menu setup tv cbl menu dvd setup aux menu
C
B
D
C D
A B setup setup
C
B
D
C D tv cbl menu dvd aux menu menu
A B C
A B C D
A B C D
A B C tv cbl dvd aux tv cbl dvd aux tv cbl dvd aux setup setup
D menu list
A list
B list setup
C D exit input tv cbl tv dvd dvd exit input aux list
A list
B C list setup
D exit input tv cbl tv dvd dvd exit input aux exit menu list
A list
B C
Using Your Remote, cont.
list setup exit exit
D exit
3. Press and release the
MUTE button.
input
4. Press and release the
VOL - button.
The red indicator light will blink twice and go off.
tv cbl tv dvd dvd aux menu list list
A menu
A
B menu
A setup exit setup
C
B
D
C D tv cbl dvd
B tv cbl menu tv cbl list dvd
C
B dvd menu
A exit input aux list setup
D
C aux
B setup
D exit menu setup
C D list
A aux exit menu
A
B menu tv cbl
B
A tv cbl menu list setup exit tv dvd list menu list setup input cbl dvd setup aux aux exit list
A aux
A
B list setup
Code Identification
dvd input aux menu tv input aux
1. Press and hold the
SETUP button
until the red indicator stays on
exit
C setup
A menu
A
B C setup
D tv cbl tv
2. Press and release the desired device button (
TV, CBL, DVD, AUX) you would
dvd exit menu list menu
A exit
3. Press and release
ENTER button.
4. Press and release the
#1 button.
Count the number of times the remote
B C D dvd
C
B
A B setup
C D exit
C D input aux
D exit list tv cbl exit menu
A
B C input
D
the
#2, #3 and #4 buttons for the
remaining digits.
dvd aux
5. Press and release
ENTER button to exit
this mode.
Reset to Factory Settings
list setup
1. Press and hold the
SETUP button
until the red indicator stays on
list
B C D
release the button.
2. Press and release the
MUTE button.
3. Press and release the number
#0
button. The red indicator light will flash twice.
list exit list exit list exit
11
Troubleshooting
Remote does not operate your device.
• Press the device button of the device you wish to control.
• Program the remote with a new code.
• Install new batteries. (You might have to reprogram your remote after installing new batteries.)
• Remote may not be compatible with your device.
Remote does not operate some features of
your device.
• Sometimes a particular code might operate some features but not all. Try programing remote with a new code.
• Remote may not be able to operate all features of your device or button names might be different than that of your original remote.
Red Indicator blinks and stays on after you program a product code.
• Remote did not accept the code.
• Try to program the code again or try a different code.
Remote Code is not available for a combo device
(e.g. TV/VCR)
• See section for controlling combo devices.
If you have any questions or would like additional information, please visit our web site www.jascoproducts.com, or contact our
Technical Support Group at 1-800-654-8483.
Between 7:30AM—5:00PM CST.
12
90-Day Limited Warranty
Jasco Products Company warrants this product to be free from manufacturing defects for a period of 90 days from the original date of consumer purchase.
This warranty is limited to the repair or replacement of this product only and does not extend to consequential or incidental damage to other products that may be used with this unit. This warranty is in lieu of all other warranties express or implied. Some states do not allow limitations on how long an implied warranty lasts or permit the exclusion or limitation of incidental or consequential damages, so the above limitations may not apply to you. This warranty gives you specific rights, and you may also have other rights which vary from state to state. If unit should prove defective within the warranty period, return prepaid with dated proof of purchase to:
Jasco Products Company
10 East Memorial Road
Oklahoma City, OK 73114 www.jascoproducts.com
Made in China
GE is a trademark of General Electric Company and is under license by Jasco Products Company LLC, 10 E.
Memorial Rd., Oklahoma City, OK 73114.
This Jasco product comes with a 90-day limited warranty. Visit www.jascoproducts.com for warranty details and product registration.
Questions? Contact us at 1-800-654-8483 between
7:30AM—5:00PM CST.
13
FCC Statement
This device complies with part 15 of the FCC rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FCC NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encourage to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This Class B digital apparatus complies with Canadian
ICES-003.
Cet appareil numérique de la classe B est conforme á la norme NMB-003 du Canada
14
15
11695
12/16/13
Manual Version 01
7252
16
input tv cbl dvd aux menu
A B setup
C D
Universal Remote
Instruction Manual
Control Remoto Universal
Manual de Instrucciones
11695
input tv cbl dvd aux menu
A B setup
C D input tv cbl dvd aux menu
A B C setup
D list exit list exit list exit
17
7252
Índice
Introducción ..................................................................................18
Configuración ...............................................................................19
Funciones de los Botones .......................................................20
Programación de su Control Remoto ...............................22
Entrada Directa de Códigos ...........................................22
Búsqueda Automática de Códigos .............................24
Control de Aparatos Combinados ...............................25
Uso de su Control Remoto ....................................................26
Función de Volumen Principal .....................................26
Para Restablecer las Configuraciones
Predeterminadas .................................................................27
Solución de Problemas ...........................................................28
Garantía ..........................................................................................29
Declaración de la FCC ..............................................................30
Introducción
Felicitaciones por su compra del Control remoto universal GE. Este mando a distancia es capaz de operar miles de dispositivos de audio / video incluyendo televisores, reproductores de DVD, cable, satélite y más!
IMPORTANTE: GUARDE ESTE MANUAL Y LA LISTA DE
CÓDIGOS PARA CONSULTARLOS EN EL FUTURO
18
Configuración
Su control remoto universal necesita dos (2) pilas tamaño
AAA (no se incluyen). Se recomiendan pilas alcalinas.
Para Instalar las Pilas
1. Presione la pestaña y levante la tapa en la parte posterior del control remoto.
2. Inserte dos (2) pilas tamaño AAA, de manera que las marcas (+) y (-) de las pilas coincidan con las marcas (+) y (-) en el interior del compartimiento de las pilas.
Asegúrese de usar pilas nuevas.
3. Presione la tapa del compartimiento de las pilas en su lugar.
NOTA: Si su control remoto deja de funcionar correctamente, reemplace las pilas por otras nuevas. El control remoto conservará los códigos que ha programado durante un máximo de 10 minutos después de retirar las pilas.
Precauciones con las Pilas
• No use pilas nuevas con pilas usadas.
• No use pilas alcalinas con pilas estándar (carbono-zinc) o con pilas recargables (Ni-Cd, Ni-MH, etc.).
• Siempre quite las baterías viejas, débiles o descargadas con prontitud y recíclelas o deséchelas de acuerdo con las regulaciones locales y nacionales.
Ahorrador de Pilas
Su control remoto se apaga automáticamente si los botones se presionan durante más de 8 segundos. Esto le ahorrará las pilas si el control remoto se permanece en un lugar donde los botones quedan presionados (por ejemplo, entre los cojines del sofá).
Protección de Ahorros
Usted tendrá hasta 10 minutos para cambiar las pilas del control remoto sin perder los códigos que haya programado. Sin embargo, no presione ningún botón hasta que haya instalado las pilas nuevas en el control remoto.
Si presiona los botones sin haber instalado las pilas en el control remoto, se perderán todos los códigos.
19
input tv cbl dvd aux menu
A B setup
C D list exit
Funciones de los Botones
tv cbl
TV, CBL, DVD, AUX
Selecciona el dispositivo que se va a controlar.
REW (rewind), FF (fast
forward), PAUSE
dvd aux
control que operan su videograbadora digital aun cuando el control
menu
A B
para operar el televisor.
También opera la
C D
(Scan) anterior/siguiente del DVD.
MENU para mostrar el menú en el televisor.
A, B, C, D Usa A,
B, C, D funciones en los dispositivos
list
ARRIBA, ABAJO,
IZQUIERDA y
DERECHA Botones de navegación.
VOLUME ARRIBA/ABAJO
Cambia el nivel de volumen del producto, normalmente el del televisor.
MUTE Apaga el sonido del televisor mientras que la imagen continúa.
DOT (•) Se utiliza para seleccionar los canales digitales, por ejemplo:
2.3.
list input tv cbl dvd aux menu
A B C setup
D exit
20
input tv cbl dvd aux menu
A B setup
C D list exit input tv cbl dvd aux menu
A B setup
C D list exit
Funciones de los Botones, continuación
ON•OFF Enciende y apaga dispositivos.
input tv cbl dvd aux menu list
A B C setup
D exit
21
INPUT Selecciona las entradas de video de las fuentes de visualización disponibles.
GUIDE Visualiza en pantalla la guía de programas de satélite o cable.
SETUP Se utiliza para configurar el control remoto y para la función de búsqueda de códigos.
INFO Visualiza en pantalla la información del canal, etc.
OK Selecciona los elementos del menú para el dispositivo que está controlando
EXIT Sale de los menús en pantalla y/o regresa a la selección previa en pantalla.
CHANNEL ARRIBA/
ABAJO
Cambia los canales.
Tenga en cuenta que los botones de la DVR también controlan el
DVD cuando está en modo DVD.
(Prev. Ch)
Regresa al canal previamente seleccionado o botón de repetición de DVD.
NÚMEROS Introduzca números para la selección directa de canales. Algunos dispositivos necesitan que se presione ENTER después de la selección del canal.
Programación de su Control Remoto
menu list
A B input tv cbl dvd aux setup
C D menu list tv cbl dvd aux
B C tv cbl menu setup list
D exit
B input dvd aux setup tv input cbl dvd aux
C D menu
A B setup
C D tv cbl dvd menu list list
B C exit setup
D tv cbl menu tv cbl input dvd aux input
A
A
B aux list exit
C D exit
Su control remoto universal GE está diseñado para controlar múltiples dispositivos de audio/video como televisores, DVD, videograbadoras digitales, aparatos de satélite, cable y audio con un solo control remoto. Para utilizar este control remoto, tendrá que programarlo para que controle los dispositivos de su elección. Hay dos maneras de programar el control remoto: entrada directa de códigos y búsqueda automática de códigos.
Entrada Directa de Códigos (se Recomienda) dvd list tv menu
A input aux list
1. Localice la lista de códigos para controles remotos que viene en este manual. Busque la
CATEGORÍA DE DISPOSITIVOS que desea programar (por ejemplo
TV, CBL,
DVD, AUX
) y luego encuentre la
MARCA de dicho dispositivo. Encierre dentro de círculos todos los códigos de esa marca.
Por ejemplo: Para un televisor GE, busque la sección de códigos de televisores, luego encierre dentro de círculos todos los códigos para televisores GE.
2. Encienda manualmente el dispositivo que desea controlar.
setup cbl dvd input aux
3. Mantenga presionado el botón
SETUP hasta que el indicador rojo permanezca
D
B C setup
D
encendido (aproximadamente 2 segundos) y luego suelte el botón
SETUP.
4. Presione y suelte el botón del dispositivo
tv cbl
TV, CBL,
DVD, AUX
). El indicador rojo parpadeará una vez y luego permanecerá encendido.
menu exit
5. Introduzca el primer código de 4 dígitos que encontró en la lista de códigos mediante los botones numéricos en el control remoto. Si el código introducido
B C D
Si el código introducido no es válido, el indicador rojo parpadeará y permanecerá encendido, permitiéndole introducir otro código.
Nota: Si no presiona ningún botón durante
35 segundos, el control remoto saldrá del modo de configuración y tendrá que comenzar de nuevo.
6. Apunte al dispositivo con el control
22
input tv cbl dvd aux menu
A B setup
C D list exit input tv cbl dvd aux menu
A B setup
C D list exit
Programación de su Control Remoto, cont.
tv cbl
remoto. Presione el botón de encendido y apagado (
ON – OFF). Si el dispositivo se apaga, el dispositivo no necesita más programación. Si el dispositivo no se apaga, regrese al paso 3 y utilice el código siguiente de la lista de códigos.
dvd aux
dispositivo.
menu
A
7. Repita este proceso con cada dispositivo
(por ejemplo TV, CBL, DVD, AUX) en su sistema de entretenimiento doméstico que desea controlar.
B C D
Notas Sobre la Programación
• Si el dispositivo no responde al control remoto después de probar todos los códigos de la lista o si su marca no aparece en la lista de códigos, utilice el método de búsqueda automática de códigos para programar el control remoto.
• A veces, el primer código que "funciona" con un dispositivo sólo podrá utilizar algunas funciones de su dispositivo. Puede que otro código de la lista de códigos realice más funciones. Pruebe otros códigos de la lista de códigos hasta encontrar una mayor funcionalidad.
• Con el método de entrada directa de códigos, puede programar cualquier botón de dispositivo para controlar cualquier dispositivo de su sistema de entretenimiento doméstico. Por ejemplo, puede usar el botón de dispositivo
AUX para controlar un receptor de audio o un DVD, una videograbadora, equipo de satélite, etc.
• Para aparatos combinados, puede que tenga que introducir un código para cada dispositivo. Por ejemplo, para un dispositivo de videograbadora/DVD, puede que tenga que introducir un código para el DVD en el botón
DVD e introducir un código para la videograbadora en un botón de dispositivo diferente en el control remoto.
• Escriba el código encontrado que funciona en el dispositivo para consultarlo en el futuro
23
Programación de su control remoto, cont.
input tv cbl dvd tv cbl aux tv cbl dvd aux input tv cbl dvd menu list
A B menu
C D
A menu list list menu
A list list
B
B tv cbl
A B
B
C D
C setup
C D dvd aux setup exit
C D exit setup
D exit exit
B tv cbl dvd aux tv cbl
B menu
C D
A B tv cbl menu list list
A B menu list list
A B
Búsqueda Automática de Códigos
La búsqueda automática de códigos busca
input dvd aux input tv cbl dvd
en el control remoto. Antes de comenzar la búsqueda
dvd
cuando lo encuentre.
dvd tv aux cbl aux input tv cbl dvd
C D menu setup input
A
C D dvd aux
C
C setup
D exit setup
D exit exit
B C
A menu
A
D
2. Mantenga presionado el botón
SETUP
B C
encendido (aproximadamente 2 segundos) y luego suelte el botón.
B C tv cbl
D
D
TV, CBL,
DVD, AUX
). El indicador rojo parpadeará una vez y luego permanecerá encendido.
menu list list
A
4. Apunte al dispositivo con el control remoto y presione y suelte el botón de encendido y apagado (
B C D
ON - OFF), para televisor, o el botón
PLAY, para DVD, videograbadora, etc., para iniciar la búsqueda. El indicador
aux
2 segundos) mientras el control remoto está buscando. Nota: El mando a distancia hay que señalar en el dispositivo para la
menu list list
A
5. Coloque el dedo en el botón
# 1 para que
B C D
la reproducción, presione el botón # 1 para bloquear el código. El indicador rojo se apagará.
Nota: Usted tendrá aproximadamente dos segundos después de que el dispositivo se apague o inicie la reproducción para bloquear el código.
7. Apunte al dispositivo con el control remoto y compruebe si el control remoto controla el dispositivo que desea. Si lo hace, el dispositivo ya no necesita más programación. Si no lo controla, regrese al paso 2 y comience la búsqueda automática de nuevo.
8. Repita este proceso con cada dispositivo
24
Programación de su control remoto, cont.
(por ejemplo TV, CBL, DVD, AUX) de su sistema de entretenimiento doméstico que desea controlar. Se pueden programar cuatro dispositivos.
Notas Sobre la Programación
• Este proceso puede tardar varios minutos por cuanto el control remoto contiene muchos códigos.
• Al utilizar el método de programación de búsqueda automática de códigos, el botón de dispositivo que corresponde al tipo de dispositivo que desea controlar debe estar seleccionado (por ejemplo, el botón de dispositivo
TV debe seleccionarse en el paso 3 si desea controlar un televisor, el botón de dispositivo
DVD para un reproductor de DVD, etc.).
• El botón
SETUP se puede utilizar durante el proceso de búsqueda para invertir la dirección de la búsqueda de los códigos del control remoto. Por ejemplo, si pasa por alto el código para su dispositivo y el control remoto sigue buscando (lo indica el parpadeo de la luz roja), presione el botón
SETUP y la búsqueda de códigos invertirá la dirección y regresará al código.
• A veces, el primer código que "funciona" para el dispositivo sólo podrá utilizar algunas funciones de su dispositivo. Puede que otro código de la lista de códigos realice más funciones. Continúe la búsqueda automática de códigos como se indicó anteriormente hasta que encuentre el mejor código.
Control de Aparatos Combinados
Algunos dispositivos combinados (por ejemplo, televisor/ videograbadora, televisor/DVD, DVD/videograbadora, etc.) necesitarán la configuración de dos botones de modo diferentes para el control de las dos partes del aparato combinados. Por ejemplo, si usted tiene una combinación de televisor/DVD, puede que tenga que configurar un código en el botón TV para controlar la parte de televisión y un código separado (en cualquier otro botón de modo) para controlar la parte del reproductor de DVD.
25
A menu
A B tv cbl list setup dvd input
C D aux
B menu
A list list tv cbl dvd input aux menu tv cbl dvd setup tv cbl
A dvd
B input
C D input tv cbl dvd input aux aux menu tv cbl dvd setup tv cbl
A dvd
B input
C D input
Uso de su Control Remoto
tv cbl dvd aux input aux setup
Función de Volumen Principal tv cbl dvd input aux tv menu cbl
A dvd
control de volumen siempre controlará. Por ejemplo, el
B C aux
D
C D
B C D exit exit input tv cbl dvd aux
C D exit
A menu
A B tv cbl list setup dvd input
C D aux
B list
A list
B C D exit exit input tv cbl dvd aux exit menu
A B C tv cbl dvd list
A list list
B C setup input
D aux
D exit exit input tv cbl dvd aux
1. Mantenga presionado el botón SETUP hasta que el indicador rojo permanezca encendido (aproximadamente 2 segundos) y luego suelte el botón.
2. Presione y suelte el botón de dispositivo deseado (
TV, CBL, DVD, AUX) para el dispositivo que desea configurar para controlar el volumen.
3. Presione y suelte el botón MUTE.
exit
4. Presione y suelte el botón
VOL +.
El indicador rojo parpadeará dos veces y después se apagará.
Para poner a prueba la función, ponga el control remoto en otro modo, como el de
TV, si programó el receptor de audio como dispositivo de volumen principal. Apunte al receptor de audio con el control remoto, mantenga presionado el botón
VOL - o el botón
VOL +. Si el volumen del receptor de audio cambia, entonces el control remoto está programado correctamente. Si el volumen del televisor cambia y no el del receptor de audio, tendrá que repetir los pasos anteriores y poner a prueba de nuevo.
menu
A menu
A list
B
B setup
C D tv cbl dvd aux setup
C D menu
A menu
B
B setup
C D tv cbl dvd aux setup
C D menu
A B C tv cbl dvd
Para Desactivar la Función de Volumen Principal setup
1. Mantenga presionado el botón
SETUP hasta que el indicador rojo permanezca encendido (aproximadamente 2 segundos) y luego suelte el botón.
aux
2. Presione y suelte el botón de dispositivo (
TV,
CBL, DVD, AUX) que está programado para controlar la función de volumen principal.
3. Presione y suelte el botón MUTE.
26
menu setup
A list
B C list exit list exit list exit
tv cbl tv cbl tv cbl dvd aux input input aux tv cbl tv cbl tv cbl dvd aux input input aux tv cbl tv cbl tv cbl dvd aux input menu menu setup setup menu menu setup setup menu menu
A B tv cbl
A
C
B
A
D
C
B
D
C D
A dvd aux
B tv cbl
A
C
B
A
C
B
D
C D
D menu
A dvd aux tv cbl
A
B C dvd menu setup aux setup input aux setup
D menu setup menu setup menu setup list
A C list
D exit exit input tv cbl dvd aux list
C list
D exit exit input tv cbl dvd aux exit list
A D exit tv cbl dvd
4. Presione y suelte el botón VOL - .
El indicador rojo parpadeará dos veces y se
aux tv cbl list menu list
A dvd aux
B menu setup
A B exit setup
C D input
C D tv cbl tv dvd cbl dvd list menu input
A aux menu
B menu input setup
A
C
B
D exit
C D exit list tv cbl setup
B menu setup input
A tv cbl dvd aux
B exit setup
C menu
D setup
B input
D
C D tv cbl
A tv dvd cbl dvd menu dvd
B aux menu input list setup exit list
A
C
B
D exit
C D exit tv cbl list menu aux
A
B setup list tv cbl dvd aux
Identificación de códigos dvd input aux setup
C D menu
A
B C tv
1. Mantenga presionado el botón
tv menu
A cbl dvd exit setup aux
B C cbl
B C
D tv
D dvd cbl
D dvd aux
SETUP hasta que el indicador rojo permanezca encendido
(aproximadamente 2 segundos) y luego suelte el botón.
2. Presione y suelte el botón de dispositivo deseado (
TV, CBL, DVD, AUX) para el que le gustaría el código.
3. Presione y suelte el botón
ENTER.
exit list exit menu menu
4. Presione y suelte el botón
# 1. Cuente el número de veces que parpadea la luz del control remoto. Este es el número que corresponde al primer dígito del código.
D
# 2, # 3 y # 4 para los dígitos restantes.
exit input
5. Presione y suelte el botón
ENTER para salir de este modo.
tv cbl dvd aux tv cbl dvd aux menu
A B list
C D exit
A B list
C D exit tv cbl
A list dvd aux
Para Restablecer las Configuración
Predeterminadas
B C D
1. Mantenga presionado el botón
SETUP hasta que el indicador rojo permanezca encendido (aproximadamente 2 segundos) y luego suelte el botón.
2. Presione y suelte el botón
MUTE.
3. Presione y suelte el botón de número # 0. El indicador rojo parpadeará dos veces.
list exit list exit list exit
27
Solución de Problemas
El control remoto no controla el dispositivo.
• Presione el botón de dispositivo del dispositivo que desea controlar.
• Programe el control remoto con un código nuevo.
• Instale pilas nuevas. (Puede que tenga que volver a programar el control remoto después de instalar pilas nuevas.)
• Puede que el control remoto no sea compatible con el dispositivo.
El control remoto no controla algunas funciones del dispositivo.
• A veces un código particular podría utilizar algunas funciones pero no todas. Trate de programar el control remoto con otro código.
• Puede que el control remoto no controle todas las funciones de su dispositivo o que los nombres de los botones sean diferentes a los de su dispositivo
El indicador rojo parpadea y permanece encendido después de programar un código de producto.
• El control remoto no aceptó el código.
• Trate de programar el código nuevamente o pruebe otro código.
El código del control remoto no está disponible para un aparato combinado (por ejemplo, televisor / videograbadora)
• Consulte la sección para controlar aparatos combinados
Si tiene preguntas o le gustaría recibir información adicional, por favor visite nuestro sitio Web, www.jascoproducts.com, o contacte nuestro Grupo de Soporte Técnico el 1-800-654-8483.
entre 7:30AM—5:00PM CST.
28
Garantía Limitada de 90 Días
Jasco Products Company garantiza que este producto está libre de defectos de fabricación durante un periodo de noventa días a partir de la fecha original de compra por el consumidor. Esta garantía se limita a la reparación o sustitución de este producto solamente y no se extiende a daños incidentales o derivados a otros productos que se usen con esta unidad. Esta garantía remplaza a todas las demás garantías expresas o implícitas. Algunos estados no permiten limitaciones en cuanto a la duración de garantías implícitas ni la exclusión o limitación de daños incidentales o derivados; por lo tanto, puede que las anteriores limitaciones no se apliquen en su caso. Esta garantía le otorga a usted derechos específicos y otros derechos que puede tener según el estado en que reside. Si comprueba que la unidad es defectuosa dentro del periodo de garantía, devuélvala con porte prepagado y prueba de compra con fecha a:
Jasco Products Company
10 East Memorial Road
Oklahoma City, OK 73114 www.jascoproducts.com
HECHO EN CHINA
GE es una marca registrada de la companía General
Electric Company y es utilizada bajo licencia a la companía
Jasco Prodcucts Company LLC, 10 E. Memorial Rd.,
Oklahoma City, OK 73114.
Este producto de Jasco Products tiene una garantía limitada de 90 días. Visite www.jascoproducts.com para detalles.
¿Tiene preguntas? Comuníquese al 1-800-654-8483 entre las 7:30 a. m. y las 5:00 p. m. CST (hora central estándar).
29
Declaración de la FCC
Este dispositivo cumple con el artículo 15 de las normas de la Federal Communications Commission (FCC, comisión federal de comunicaciones de EE. UU.). Su funcionamiento está sujeto a las siguientes dos condiciones: (1) este dispositivo no puede causar interferencias perjudiciales, y
(2) este dispositivo debe aceptar las interferencias recibidas, incluidas las interferencias que puedan provocar un funcionamiento no deseado.
NOTA DE LA FCC: El fabricante no es responsable de las interferencias de radio o televisión ocasionadas por modificaciones no autorizadas a este equipo. Tales modificaciones pueden anular la autoridad del usuario para poner en funcionamiento el equipo.
NOTA: Este equipo ha sido probado y cumple con los límites para dispositivos digitales de Clase B, de conformidad con el artículo 15 de las normas de la FCC. Estos límites están diseñados para proporcionar una protección razonable contra interferencias perjudiciales en instalaciones residenciales. Este equipo genera, utiliza y puede irradiar energía de radiofrecuencia y, si no se instala y utiliza de acuerdo con las instrucciones, puede causar interferencias perjudiciales a las radiocomunicaciones. Sin embargo, no hay garantía de que no se produzcan interferencias en una instalación en particular. Si este equipo causa interferencias perjudiciales en la recepción de radio o televisión, lo cual se puede determinar apagando y encendiendo el equipo, se le recomienda al usuario que intente corregir las interferencias mediante una o más de las siguientes medidas:
• Reoriente o reubique la antena receptora.
• Aumente la distancia entre el equipo y el receptor.
• Conecte el equipo a un tomacorriente de un circuito diferente al que está conectado el receptor.
• Consulte al distribuidor o a un técnico experto en radio o televisión para obtener ayuda.
Este aparato digital de clase B cumple con la norma canadiense ICES-003.
Cet appareil numérique de la classe B est conforme á la norme la NMB-003 du Canada
30
31
11695
12/16/13
Manual Version 01
7252
32
advertisement
Related manuals
advertisement
Table of contents
- 2 Introduction
- 3 Setup
- 4 Button Functions
- 6 Programming Your Remote
- 6 Direct Code Entry
- 8 Auto Code Search
- 9 Controlling Combo Devices
- 10 Using Your Remote
- 10 Master Volume Feature
- 11 Reset to Factory Settings
- 12 Troubleshooting
- 13 Warranty
- 14 FCC Statement
- 18 Introducción
- 19 Configuración
- 20 Funciones de los Botones
- 24 Búsqueda Automática de Códigos
- 25 Control de Aparatos Combinados
- 26 Uso de su Control Remoto
- 26 Función de Volumen Principal
- 27 Predeterminadas
- 28 Solución de Problemas
- 29 Garantía
- 30 Declaración de la FCC