KOAMTAC KDC300M-SR User manual
Anuncio
Anuncio
1
KDC User Manual
Rev 2.85.R8 / 2.86.R8 / 3.05.R8 (Rev0.3)
June 2014
2
KDC User Manual
I NTRODUCTION
Table of Contents
1.
INTRODUCTION ......................................................................................... 16
1.1
KDC Package ............................................................................................................... 17
1.2
KDC Characteristics..................................................................................................... 19
1.3
Keypad (KDC350) ........................................................................................................ 22
1.4
Input data by using a keypad (KDC350) ..................................................................... 23
1.5
Turn on the power of KDC20/30/400 ......................................................................... 24
2.
INSTALLATION ............................................................................................ 25
2.1
Bluetooth Pairing ......................................................................................................... 25
Preparing for Pairing .............................................................................................................. 25
Pairing ..................................................................................................................................... 27
2.2
KOAMTAC Installation Wizard ................................................................................... 30
Windows 7 and 8 .................................................................................................................... 30
Android ................................................................................................................................... 32
Blackberry ............................................................................................................................... 32 iPad/iPhone/iPod touch ........................................................................................................ 32
2.3
Manual Installation ...................................................................................................... 33
Windows 7/8 ........................................................................................................................... 33
3.
OPERATING YOUR KDC ............................................................................ 34
3.1
Getting Started ............................................................................................................ 34
Attach Lanyard/Hand Strap to KDC ..................................................................................... 34
Charge KDC Battery .............................................................................................................. 35
Configure KDC ....................................................................................................................... 35
3.2
Basics ............................................................................................................................ 37
Read barcodes ....................................................................................................................... 37
Read barcodes with GPS coordinates (KDC350G) ............................................................. 38
Read NFC Tag (KDC350N/400N) ......................................................................................... 38
Read HF RFID Tag (KDC450) ................................................................................................ 39
Input data by using a keypad (KDC350) .............................................................................. 39
Synchronizing data to the host device ................................................................................. 39
3.3
KDC Menu ................................................................................................................... 40
KDC Mode Menu ................................................................................................................... 56
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
3
KDC User Manual
I NTRODUCTION
View Data Menu ..................................................................................................................... 56
Set Barcodes Menu ............................................................................................................... 56
Code Options Menu .............................................................................................................. 56
Scan Options Menu ............................................................................................................... 56
Data Process Menu ................................................................................................................ 59
BT Config Menu – KDC20/30/200/250/300/400 ................................................................. 64
BT Service – KDC20/30/200/250/300/350/400 .................................................................... 66
GPS Config - 350G ................................................................................................................. 67
USB DISK - 100M/200M/250M/300M/350 ........................................................................... 68
NFC Config – KDC350N/KDC400N ..................................................................................... 69
System Menu .......................................................................................................................... 69
Pair and connect KDC20i/30i/200i/250i/300i/350i/400i and iOS4.0+ in HID iOS mode . 71 iOS Soft Keyboard toggling using BT Toggle option ........................................................ 72
3.4
LED Status .................................................................................................................... 73
KDC100/200/250/300/350 ..................................................................................................... 73
KDC20/30/400 ........................................................................................................................ 73
3.5
Empty Battery .............................................................................................................. 74
KDC100/200/250/300/350 ..................................................................................................... 74
KDC20/30/400 ........................................................................................................................ 74
3.6
Buffer Full ..................................................................................................................... 74
3.7
Reset Feature (100/200/250/300/350) or Power-on/off (KDC20/30) ......................... 75
3.8
Replace Battery ........................................................................................................... 76
4.
BLUETOOTH – KDC20/30/200/250/300/350/400 ............................... 77
4.1
Bluetooth Config ......................................................................................................... 77
ConnectDevice ....................................................................................................................... 77
Auto Connect ......................................................................................................................... 78
Auto Reconnect ..................................................................................................................... 78
Auto Power On ....................................................................................................................... 78
PWR ON Time ........................................................................................................................ 78
Auto Power Off ....................................................................................................................... 79
Beep Warning ......................................................................................................................... 79
PWR OFF Time ....................................................................................................................... 79
PowerOFF Msg ....................................................................................................................... 79
MAC Address .......................................................................................................................... 79
FW Version .............................................................................................................................. 79
Wakeup Nulls .......................................................................................................................... 80
Autolock Time ......................................................................................................................... 80
HID Keyboard ......................................................................................................................... 80
HID Initial and Inter-Character Delay .................................................................................... 80
Control character transmission in HID mode ...................................................................... 80
Function key transmission in HID mode .............................................................................. 81
Disconnect/Reconnect/BT(HID) Toggle .............................................................................. 81
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
4
KDC User Manual
I NTRODUCTION
4.2
Bluetooth Service ........................................................................................................ 82
Power ....................................................................................................................................... 82
Pairing ...................................................................................................................................... 82
Discovering .............................................................................................................................. 83
Connect To ............................................................................................................................. 83
HID Sync ................................................................................................................................. 83
5.
SYNCHRONIZATION .................................................................................. 84
5.1
KTSync Menu ............................................................................................................... 84
5.2
File Menu ..................................................................................................................... 87
Connect to KDC ..................................................................................................................... 87
Synchronize ............................................................................................................................ 87
Bluetooth ................................................................................................................................ 88
Configuration ......................................................................................................................... 88
5.3
Synchronization Settings ............................................................................................. 90
Destination of Data ................................................................................................................ 90
Synchronization Methods...................................................................................................... 91
Current KDC Wedge Method ............................................................................................... 92
Synchronization Options ....................................................................................................... 92
Application Options .............................................................................................................. 93
5.4
Barcode & KDC Settings ............................................................................................. 94
Select Symbologies and Symbology Options .................................................................... 95
Data Editing Option .............................................................................................................. 95
5.5
Other Settings ............................................................................................................. 96
5.6
KDC Menu in KTSync (KDC20/30/400) ....................................................................... 97
5.7
Mobile pKTSync .......................................................................................................... 98
5.8
Android aKTSync ......................................................................................................... 99
KDC and Android Pairing...................................................................................................... 99
Launch KTSync ....................................................................................................................... 99
Keyboard Wedge ................................................................................................................. 101
5.9
iPad/iPhone/iPod touch KTSync ............................................................................... 102
KDC20i/30i/200i/250i/300i/350i/400i connection using iPhone mode ........................... 102 iKTSync Settings ................................................................................................................... 103
How to connect and reconnect iPhone mode using UP keys ......................................... 103
5.10
Blackberry bKTSync ................................................................................................... 104
5.11
KTSync for Mac OS X ................................................................................................ 106
Connect Button .................................................................................................................... 106
Disconnect Button ............................................................................................................... 107
Synchronize Button .............................................................................................................. 107
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
5
KDC User Manual
I NTRODUCTION
Clear Button ......................................................................................................................... 107
Settings Button .................................................................................................................... 107
6.
APPLICATION GENERATION ................................................................. 110
6.1
Application Generation ............................................................................................ 111
Generate Application .......................................................................................................... 111
Data Filter Settings .............................................................................................................. 112
Application Download and Execution ............................................................................... 114
6.2
Predefined Applications ........................................................................................... 115
Master/Slave ......................................................................................................................... 115
Pick/Bin ................................................................................................................................. 116
DB Lookup Application ....................................................................................................... 119
Inventory Application .......................................................................................................... 121
7.
TROUBLESHOOTING ............................................................................... 123
8.
WARRANTY .............................................................................................. 125
9.
CONTACT INFORMATION ..................................................................... 126
10.
APPENDIX A – BARCODE & SCAN OPTIONS ................................ 127
10.1
Symbologies .............................................................................................................. 127
Bookland EAN vs. EAN-13 .................................................................................................. 128
Add-on Symbologies .......................................................................................................... 128
10.2
Code Options (KDC20/30/100/200/250/410/415) ................................................... 129
Reverse Direction ................................................................................................................. 129
Symbology Conversion ....................................................................................................... 130
Verification of Optional “Check Digit” .............................................................................. 130
Transmission of “Check Digit” ........................................................................................... 130
Resolution of Inconsistencies ............................................................................................. 131
10.3
Miscellaneous Barcode Information ........................................................................ 132
Height of a Linear Barcode ................................................................................................. 132
Check Characters ................................................................................................................. 132
Prevent Interleave 2 of 5 Partial Reading .......................................................................... 132
Equation to Determining Potential Number of Stored Barcodes ................................... 133
Data Buffer Full .................................................................................................................... 133
11.
APPENDIX B –FAQ ............................................................................... 134
11.1
Symbology ................................................................................................................. 134
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
6
KDC User Manual
I NTRODUCTION
11.2
Host Interface ............................................................................................................ 135
11.3
Battery ........................................................................................................................ 135
11.4
Memory ...................................................................................................................... 136
11.5
Programming ............................................................................................................. 136
12.
APPENDIX C – 1D SPECIAL BARCODES
(KDC20/100/200/250/350L/410/415) ........................................................ 137
12.1
Set Symbologies ........................................................................................................ 137
12.2
Barcode Options ....................................................................................................... 140
12.3
Delete Last Scanned Barcode .................................................................................. 143
12.4
Scan Options ............................................................................................................. 144
12.5
Scan Timeout ............................................................................................................. 145
12.6
Minimum Barcode Length ........................................................................................ 146
12.7
Security Level ............................................................................................................. 149
12.8
Data Process - Wedge/Store & Enter Key ............................................................... 150
12.9
Data Process - Data Edit ........................................................................................... 151
12.10
Data Process - Data Format & Handshake .......................................................... 152
12.11
Data Process - Termination Character & Duplicate Check .................... 153
12.12
Bluetooth ............................................................................................................... 154
12.13
Bluetooth Auto Power On Time ........................................................................... 157
12.14
Bluetooth Power Off Time .................................................................................... 158
12.15
HID Auto Lock Time .............................................................................................. 160
12.16
HID Keyboard ........................................................................................................ 161
12.17
HID Initial Delay ..................................................................................................... 162
12.18
HID Character Delay ............................................................................................. 163
12.19
HID Control Character .......................................................................................... 164
12.20
System .................................................................................................................... 165
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
7
KDC User Manual
I NTRODUCTION
12.21
Sleep Timeout ....................................................................................................... 168
12.22
ETC ......................................................................................................................... 169
12.23
Function ................................................................................................................. 170
12.24
Number .................................................................................................................. 171
12.25
Lower Case Alphabet ............................................................................................ 172
12.26
Upper Case Alphabet ........................................................................................... 174
12.27
Control Character .................................................................................................. 176
12.28
Symbol Character .................................................................................................. 177
12.29
GPS (GPS Model Only) ......................................................................................... 180
12.30
GPS/BT Auto Power Off Timeout(GPS Model Only) .......................................... 181
12.31
NFC (NFC Model Only) ........................................................................................ 182
12.32
USB Disk (M Model Only) ..................................................................................... 183
13.
APPENDIX D – 2D SPECIAL BARCODES (KDC30/300/350C/420
/425/450) ......................................................................................................... 184
13.1
Set Symbologies ........................................................................................................ 184
13.2
Barcode Options ....................................................................................................... 184
13.3
Delete Last Scanned Barcode .................................................................................. 184
13.4
Scan Options ............................................................................................................. 185
13.5
Scan Timeout ............................................................................................................. 186
13.6
Minimum Barcode Length ........................................................................................ 187
13.7
Image Capture ........................................................................................................... 190
13.8
Data Process - Wedge/Store & Enter Key ............................................................... 191
13.9
Data Process - Data Edit ........................................................................................... 192
13.10
Data Process – Data Format & Handshake ......................................................... 193
13.11
Data Process - Termination Character & Duplicate Check ................................ 194
13.12
Bluetooth ............................................................................................................... 195
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
8
KDC User Manual
I NTRODUCTION
13.13
Bluetooth Auto Power On Time ........................................................................... 198
13.14
Bluetooth Power Off Time .................................................................................... 199
13.15
HID Auto Lock Time .............................................................................................. 201
13.16
HID Keyboard ........................................................................................................ 202
13.17
HID Initial Delay ..................................................................................................... 203
13.18
HID Character Delay ............................................................................................. 204
13.19
HID Control Character .......................................................................................... 205
13.20
System .................................................................................................................... 206
13.21
Sleep Timeout ....................................................................................................... 209
13.22
Function ................................................................................................................. 210
13.23
Number .................................................................................................................. 211
13.24
Lower Case Alphabet ............................................................................................ 212
13.25
Upper Case Alphabet ........................................................................................... 214
13.26
Control Character .................................................................................................. 216
13.27
Symbol Character .................................................................................................. 217
13.28
GPS (GPS Model Only) ......................................................................................... 220
13.29
GPS/BT Auto Power Off Timeout(GPS Model Only) .......................................... 221
13.30
NFC (NFC Model Only) ........................................................................................ 222
13.31
USB Disk (M Model Only) ..................................................................................... 223
14.
APPENDIX E - MSR SPECIAL BARCODES (KDC415/425MSR) .... 224
14.1
KDC415MSR .............................................................................................................. 224
14.2
KDC425MSR .............................................................................................................. 227
15.
APPENDIX F – MULTIPLE SPECIAL BARCODES ............................. 230
15.1
KDC20/KDC100/KDC250/KDC350L/KDC410/KDC415 ........................................... 230
15.2
KDC30/KDC300/KDC350C/KDC420/KDC425/KDC450 .......................................... 231
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
9
KDC User Manual
I NTRODUCTION
List of Figures
Figure 1- KDC Package .................................................................................................................................... 18
Figure 2 - KDC20/30 Overview ...................................................................................................................... 19
Figure 3 - KDC100 Overview .......................................................................................................................... 20
Figure 4 - KDC200/250/300/350 Overview ................................................................................................ 21
Figure 5 - KDC400 Overview .......................................................................................................................... 21
Figure 6 - How to turn on the power in KDC20/30/400 ........................................................................ 24
Figure 7 - Selecting a Bluetooth device type from the KDC menu .................................................. 26
Figure 8 - Selecting Pairing mode in KDC................................................................................................. 27
Figure 9 - Pairing mode button in KDC20/30/400 .................................................................................. 27
Figure 10 - Finding Bluetooth MAC Address ........................................................................................... 28
Figure 11 - Connecting KDC with a smart phone by scanning Bluetooth MAC Address
Barcode .................................................................................................................................................................. 29
Figure 12 - Location of KDC Menu and use of buttons (KDC100/200/250/300) .......................... 35
Figure 13 - Location and use of buttons on a keypad (KDC350) ....................................................... 36
Figure 14 - KDC Display ................................................................................................................................... 37
Figure 15 - Scanning barcodes using KTSync .......................................................................................... 37
Figure 16 - Location for reading NFC Tag ................................................................................................ 39
Figure 17 - Delete Function in KDC20/30 .................................................................................................. 56
Figure 18 - Replacing a Battery ..................................................................................................................... 76
Figure 19 - KTSync ® Synchronizer Menu .................................................................................................... 85
Figure 20 - File Menu ........................................................................................................................................ 85
Figure 21 – Setting Menu ................................................................................................................................ 86
Figure 22 - Application Menu ........................................................................................................................ 86
Figure 23 - About Menu ................................................................................................................................... 86
Figure 24 - COM Port Selection for KDC ................................................................................................... 87
Figure 25 - Bluetooth Device Registry ........................................................................................................ 88
Figure 26 – Configuration................................................................................................................................ 89
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
10
KDC User Manual
I NTRODUCTION
Figure 27 - KTSync ® Synchronization Settings ......................................................................................... 90
Figure 28 - Barcode & KDC Settings, Symbologies, Data Editing and Scan Options ............... 94
Figure 29 - KTSync ® Confirmation Settings .............................................................................................. 96
Figure 30 - KDC Menu in KTSync (KDC20/30/400) ................................................................................. 97
Figure 31 - Mobile pKTSync ........................................................................................................................... 98
Figure 32 - Android aKTSync ....................................................................................................................... 100
Figure 33 - iPad/iPhone/iPod touch KTSync ........................................................................................... 103
Figure 34 - Blackberry bKTSync .................................................................................................................. 105
Figure 35 - Application Menu ...................................................................................................................... 110
Figure 36 - Application Warning Window ............................................................................................... 110
Figure 37 - Application Generation Menu .............................................................................................. 111
Figure 38 - Data Filter Settings .................................................................................................................... 112
Figure 39 - Master/Slave Application Settings ...................................................................................... 116
Figure 40 - Master/Slave Application Flow Chart ................................................................................. 116
Figure 41 - Pick/BIN Application Menu .................................................................................................... 117
Figure 42 - Pick/BIN Application Flow Chart .......................................................................................... 118
Figure 43 - DB Lookup Application Menu ............................................................................................... 120
Figure 44 - Inventory Application ............................................................................................................... 122
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
KDC User Manual
I NTRODUCTION
List of Tables
Table 1 - Features of KDC ............................................................................................................................... 16
Table 2 - Number of hours required to fully charge a KDC Battery ................................................. 35
Table 3 - KDC Menu .......................................................................................................................................... 55
Table 4 - KDC350C Minimum Barcode Length ....................................................................................... 58
Table 5 - Explanation of LEDs ........................................................................................................................ 73
Table 6 - Troubleshooting Techniques .................................................................................................... 124
Table 7 - Symbologies Supported by KDC ............................................................................................. 127
Table 8 - Add-on for EAN-13 Symbology ................................................................................................ 128
Table 9 - Add-on for EAN-8 Symbology .................................................................................................. 129
Table 10 - Symbology Conversion ............................................................................................................. 130
Table 11 - Verification of Optional "Check Digit" ................................................................................ 130
Table 12 - Transmission of "Check Digit" ............................................................................................... 131
Table 13 - Resolution of Inconsistencies .................................................................................................. 131
Table 14 – Symbologies supported by KDC .......................................................................................... 134
11
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
12
KDC User Manual
I NTRODUCTION
COPYRIGHT, LICENSE, and WARNING PAGE
Copyright 2002-2014 by KOAMTAC, Inc. All rights reserved.
No part of this publication may be reproduced or used in any form, or by any electrical or mechanical means, without permission in writing from KOAMTAC, Inc.
The material in this manual is subject to change without notice. KOAMTAC reserves the right to make changes to any product to improve reliability, function, or design.
KOAMTAC does not assume any product liability arising out of, or in connection with, the application or use of any product, circuit, or application described herein.
Follow all warnings and instructions marked on manual and units. Use only the power source specified in this manual or marked on the units.
May be covered under the patent laws of the US and other countries. For patent information in the US, see http://www.KOAMTAC.com/corpVis.html. Korea Patent
No. 10-2013-0010827. Patent pending in UK as GB2492615 and in Korea as publication 10-2010-0136194.
KDC ® is a registered trademark and property of KOAMTAC, Inc.
KoamTac
KTSync
® is a registered trademark and property of KOAMTAC, Inc.
® is a registered trademark and property of KOAMTAC, Inc.
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS UNIT TO ANY TYPE OF
MOISTURE. DO NOT LOOK DIRECTLY INTO LASER OR POINT THE LASER INTO ANOTHER
PERSON’S EYES. EXPOSURE TO THE BEAM MAY CAUSE EYE DAMAGE.
CAUTION:
Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the user’s authority to operate the equipment.
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
13
KDC User Manual
I NTRODUCTION
Regulatory Compliance
US
FCC ID: VH9KDC20, VH9KDC100, VH9KDC200, VH9KDC250, VH9KDC300,
VH9KDC350, VH9KDC400, VH9KDC450
This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. It may cause harmful interference to radio communications if not installed and used in accordance with the instructions. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference with one or more of the following measures:
1. Reorient / Relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a different circuit than the receiver.
4. Consult with the dealer or an experienced radio/TV technician for help.
WARNING:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Europe
2200 0983
Certificate No.: EMC15688-07-01
Products intended for sale within the European Union are marked with a CE Mark which indicates compliance to applicable Directives and European Normes (EN), as follows. Amendments to these Directives or ENs are included: Normes (EN), as follows:
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
14
KDC User Manual
I NTRODUCTION
Applicable Directives:
• Radio and Telecommunications Terminal Equipment Directive 1999/5/EC
Scope of Opinion
(Essential Requirements)
Applied Specifications/Standards TCF Identification Results
Article 3.1(a) - Safety
Statement Complies
ESTCS1101-002 Complies
Article 3.1(b) – EMC
EN 60950-1:2006+A11:2009
EN 55022:2006+A1:2007
EN 55024:1998+A1:2001+A2:2003
ETSI EN 301 489-1 V1.8.1 (2008-04)
ETSI EN 301 489-17 V2.1.1 (2009-05)
ESTCE0712-007(1) Complies
Article 3.2 – Radio
Spectrum Use
ETSI EN 300 328:V1.7.1 (2006-10) ESTR0801-018(1) Complies
Japan
003WWA080049, 003WWA090274, 208-120048, 208WW110041,
208-130029, 208-140011
Article 2-1-19, 2.4GHz Wide Band low power data communication system
Korea
MSIP-CMM-A13-KDC20, AI3-KDC100, AI3-KDC200, MSIP-CMM-A13-KDC250,
MSIP-CMM-A13-KDC350, MSIP-CMM-A13-KDC350, MSIP-CMM-A13-KDC400,
MSIP-CMM-A13-KDC450
Laser Compliance
KDC20/100/200/250/350L/410/415/430
Complies with US 21 CFR 1040.10 and 1040.11 except for deviations pursuant to laser notice no. 50, dated June 24,
2007 and IEC 60825-1 (Ed. 2.0)
Complies with IEC60825-1:1993 + A1:1997 + A2:2001
Battery Warning
This device contains a rechargeable NiMH. Never throw the battery into a fire, as that could cause the battery to explode.
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
15
KDC User Manual
I NTRODUCTION
Never short-circuit the battery by bringing the terminals in contact with another metal object. This could cause personal injury, a fire, and/or damage to the battery.
Never dispose of used batteries with other ordinary solid wastes. Batteries contain toxic substances.
Dispose of used batteries in accordance with the prevailing community regulations that apply to the disposal of batteries. Cover the metal terminals with insulating tape (this is to prevent accidental short-circuiting).
Never expose the battery to any liquid.
Always keep the battery out of reach of infants or small children.
Never shock the battery by dropping it or throwing it.
Dispose of a spent or damaged battery promptly.
WARNING: RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT
TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.
Product Disposal
This device should not be placed in municipal waste. Please check local regulations for disposal of electronic products.
Bluetooth
Core Specification: 2.1+EDR
Apple
Made for iPhone, Made for iPod, Made for iPad
Samsung
Compatible with Galaxy Series
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
16
KDC User Manual I NTRODUCTION
1. Introduction
Congratulations on purchasing KOAMTAC’s revolutionary barcode scanner and data collector. Lightweight and compact, with a user-friendly design and superior functionality,
KOAMTAC’s KDC works in a variety of portable applications. Use it independently or as an accessory to a PC, PDA, or smartphone. To find out more about KOAMTAC, Inc. and our family of products, visit us at www.KOAMTAC.com.
FEATURES KDC20 KDC30 KDC100 KDC200 KDC250 KDC300 KDC350 KDC400 KDC450
USB
CONNECTIONS
RECHARGEABLE
BATTERY
SCAN ENGINE
AUTOMATIC
DATA UPLOAD
STORES10,000+
BARCODES
KTSYNC ®
SOFTWARE
SDK
SUPPORTS
WINDOWS
XP, 7, 8 &
MOBILE 5.0+
ANDROID,
BLACKBERRY,
IOS
BLUETOOTH
GPS
NFC/RFID
MSR
USB DISK
1
NO
NO
1
NO
NO
2
NO
NO
1
NO
NO
1
NO
NO
Table 1 - Features of KDC
1
NO
NO
1
YES
NO
2
Laser/
Imager
Imager
YES
YES
2
YES
NO
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
17
KDC User Manual I NTRODUCTION
1.1 KDC Package
The standard KDC package contains:
1. One KDC Barcode Data Collector
2. USB Cable
KDC20/30 (N/A)
KDC100/200/250/300/350 (8pin Ultra mini USB Cable)
KDC400/450 (5pin Micro USB cable)
3. One Lanyard (KDC20/30/100/200/250/300/350) or One Hand Strap
(KDC400/450)
4. KOAMTAC Installation CD with
KTSync © for Microsoft Windows XP, Vista 7 and Mobile 5.0+
KDC Device Driver
User Manual
5. One KDC Protective Rubber Boot (KDC100/200/250/300).
The following KDC accessories are available to purchase from www.koamtacstore.com
or local reseller.
Protective boot for KDC20/30/350.
Smartphone cases for KDC200/250/300/400/450.
Charging cradles for KDC20/30/100/200/250/300/350/411/421/430/450
Finger Trigger Glove and KDC200/350/300 adaptor
KDC350 hardpack battery charging adaptor
KDC battery
Note
KDC400/450 smartphone cases should be purchased separately.
Depending on the region or distributor, package contents may vary.
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
18
KDC User Manual I NTRODUCTION
KDC20/30
KDC350
KDC100/200/250/300
KDC400/450
Figure 1- KDC Package
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
19
KDC User Manual I NTRODUCTION
1.2 KDC Characteristics
Before starting to use the KDC, the user should become familiar with its physical characteristics. Refer to Figure 2, Figure 3, Figure 4, and Figure 5 below that indicate the placement of SCAN, UP, and DOWN buttons, OLED display, LEDs, and ports on the KDC.
Although KDC models consist of similar buttons and LEDs, each model has different characteristics for its own purpose of use. The KDC20/30/100 include a swing-out USB connector and the KDC350 has a keypad.
KDC20/30 Barcode Reader and Data Collector
Green/Red/Orange LEDs
DELETE Button
UP Button
DOWN Button
Green/Red/Orange LEDs
UP Button
DOWN Button
KDC20
KDC30
Figure 2 - KDC20/30 Overview
SCAN Button
Type A USBswings out
DELETE Button
SCAN Button
Type A USBswings out
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
20
KDC User Manual I NTRODUCTION
KDC100 Barcode Reader and Data Collector
Green/Red/Orange LEDs
UP Button
DOWN Button
OLED Display
SCAN Button
Ultra mini USB Port
KDC100
Figure 3 - KDC100 Overview
Type A USBswings out
KDC200/250/300/350 Barcode Reader and Data Collector
Green/Red/Orange LEDs
UP Button
DOWN Button
Green/Red/Orange LEDs
OLED Display
SCAN Button
KDC200
KDC250/300
OLED Display
SCAN Button
Ultra mini USB Port
UP Button
DOWN Button
Ultra mini USB Port
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
KDC User Manual I NTRODUCTION
Green/Red/Orange LEDs
Menu Button
UP Button
Shift Button
Keypad
KDC350
Figure 4 - KDC200/250/300/350 Overview
Function Button
DOWN Button
SCAN Button
Mode Button
Ultra mini USB Port
KDC400/450 Barcode Reader and Data Collector
21
Figure 5 - KDC400 Overview
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
22
KDC User Manual I NTRODUCTION
1.3 Keypad (KDC350)
(Shift button)
Allows the user to change character input mode from capital letters to small letters, and vice versa.
(Mode button)
Allows the user to switch between ABC and number input mode.
(Up button)
While in the KDC menu, press this button to go up on the selection bar. While on the main screen, press this button and the KDC will try to connect to a BT host device.
(Down button)
While in the KDC menu, press this button to go down on the selection bar. While on the main screen, press this button to toggle the iOS soft keyboard (if the KDC is connected in HIDiOS mode).
(Number button)
Input numbers or characters
(Enter button)
Press to finish data input (if “Enter Key” option is disabled).
Press to finish data input and move cursor to next line (if “Enter
Key” option is enabled).
(Delete button) Press to delete the last character or number input
(Function button)
This button can be used in conjunction with a number key to control the KDC settings shown below.
FN + 1 Keypad light On/Off
FN + 2
FN + 3
FN + 4
FN + 5
FN + 6
FN + 0
GPS Power On/Off (KDC350 G series only)
NFC Power On/Off (KDC350 N series only)
Enter Bluetooth Pairing Mode
Bluetooth Power On/Off
Change Bluetooth profile
Factory Default
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
23
KDC User Manual I NTRODUCTION
1.4 Input data by using a keypad (KDC350)
When the KDC350 shows a blank main screen, you can start pressing numbers or characters of the barcode data that needs to be input.
See an example below: How to save the barcode data “123Koamtac”.
123_
Num
Shift Abc
123_
Shift Abc
123K
Press 1@:/ , 2ABC and
3DEF on the keypad.
Press Mode to switch to
Abc mode.
Press 5JKL on the keypad
Abc Abc
Cancel Do you want
To cancel ?
Yes No
Press Menu and select Yes to cancel input.
123K 123Koamtac
Press Shift on the keypad to change to lower case mode.
Press the keys for remaining letters.
Abc
Save
123Koamtac
Press or button to save barcode data.
SCAN
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
KDC User Manual I NTRODUCTION
1.5 Turn on the power of KDC20/30/400
KDC20/30/400 have power on/off switch. Please turn on the power first before using the device.
SCAN Button
Press SCAN and DOWN buttons simultaneously for 5 seconds. The user will hear a beep sound when it is turned on.
DOWN Button
KDC400
Slide POWER button to the right.
Figure 6 - How to turn on the power in KDC20/30/400
24
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
25
KDC User Manual Installation
2. Installation
2.1 Bluetooth Pairing
The KDC can read and store barcode data independently, but it can also be used in combination with a PC, PDA, smartphone, or tablet.
To use the KDC to read barcodes while it is paired with another device, the user should first set up a pairing between the KDC and smart device via Bluetooth. If no changes have been made in the smart device’s Bluetooth settings, the smart device will always recognize the KDC that has previously been paired. However, if changes have been made, the user will need to go through the pairing process again. The user can also refer to Chapter 4.
Bluetooth for more information about Bluetooth pairing.
Preparing for Pairing
Select a Bluetooth profile. There are two ways to set up a Bluetooth profile.
Select and scan the needed Bluetooth profile barcode from the following barcodes.
KDC 20/100/200/250/350L/410/415 (1D)
Bluetooth Profile SPP Bluetooth Profile HID iOS Bluetooth Profile IPHONE
Bluetooth Profile SPP2.0 Bluetooth Profile HID normal
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
26
KDC User Manual Installation
KDC30/300/350C/420/425/450 (2D)
Bluetooth Profile SPP Bluetooth Profile HID iOS
Bluetooth Profile IPHONE Bluetooth Profile SPP2.0
Bluetooth Profile HID normal
Or, for KDCs equipped with an LCD screen (KDC100/200/250/300/350), the user can select a Bluetooth device type from the ConnectDevice menu as shown below.
KDC Menu BT Config Connect Device iPhone Save & Exit
Figure 7 - Selecting a Bluetooth device type from the KDC menu
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
27
KDC User Manual Installation
Pairing
Option One: Connect the KDC from a host (PC, Smartphone, Tablet)
This method is recommended for first-time users or when the user is only connecting a few
KDCs.
1.
Put the KDC into Pairing mode
Select and scan the correct pairing barcode below for your KDC model, or
KDC 20/100/200/250/350L/410/415(1D)
KDC30/300/350C/420/425(2D)
Pairing
Select Pairing from the KDC menu.
From the KDC Menu Select BT Service Select Pairing
Figure 8 - Selecting Pairing mode in KDC
For the KDC20/30, press the Scan button for three seconds in order to enter into
Pairing mode. For the KDC 400, press the Up button immediately after turning the power on in order to enter into Pairing mode.
Press SCAN Button for 3 seconds
Press UP Button on the right side
Figure 9 - Pairing mode button in KDC20/30/400
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
28
KDC User Manual Installation
2.
On the host device, go to Settings -> Bluetooth, and select the KDC that needs to be paired. The KDC and host device will now communicate with each other.
Settings
Tap Bluetooth Tap the KDC
3.
After it has been installed, open KTSync and it will automatically find and connect to the
KDC. (Refer to 2.2 KOAMTAC Installation Wizard for more information about installing
KTSync)
Option Two: Connect the host device from the KDC by scanning a Special
Bluetooth MAC Address barcode
This method is recommended for advanced users or when the application or process requires the pairing of multiple KDCs to multiple host devices on a regular basis.
1.
Find the Bluetooth MAC Address of the host device.
Settings
Tap on General Tap on About Bluetooth address
Figure 10 - Finding Bluetooth MAC Address
2.
Create the Bluetooth MAC Address Barcode according to the format below.
Bluetooth MAC Address: 1234567890AB
Barcode Type (Symbology): Code 128
Contents: For KDC20/200/250/410/415, type ^FNC365 1234567890AB
For KDC30/300/420/425, type SYNMCRKDC65 1234567890AB
Options: includetext parsefnc
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
29
KDC User Manual Installation
3.
Print the Bluetooth MAC Address
Note: 2D image-based barcode readers such as the KDC30, KDC300, KDC350C, and
KDC420 series models can read barcodes that have been printed QR barcodes that are on a LCD screen.
Laser scanners such as the KDC20, KDC100, KDC200, KDC350L, and KDC410 series models are not designed to read barcodes from a LCD screen and will only read printed barcodes.
4.
Connect the KDC to the host device by scanning the Bluetooth MAC Address Barcode.
Settings
Tap on Bluetooth
Scan the BT MAC Address
Barcode
Tap on Pair Complete!
Figure 11 - Connecting KDC with a smart phone by scanning Bluetooth MAC Address Barcode
5.
Open KTSync after it has been installed, and it will automatically find the KDC and connect. (Refer to 2.2 KOAMTAC Installation Wizard for more information about installing
KTSync)
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
30
KDC User Manual Installation
2.2 KOAMTAC Installation Wizard
Windows 7 and 8
Note
WARNING: DO NOT CONNECT KDC TO USB PORT PRIOR TO DRIVER
INSTALLATION
1. Insert KOAMTAC Installation CD into the computer’s CD drive.
2. Click Start icon then My Computer icon. A list of devices on the computer will be displayed, including the disk drive containing the KOAMTAC Installation
CD.
3. Click on the KOAMTAC Installation CD icon, then the Setup directory. Click on the PC_Setup.exe file, which will execute the KTSync Setup Wizard.
If the KTSync Setup Wizard locates an older version of KTSync on the computer, the user will be prompted to remove the older program before installing the new version. Select Remove KTSync then click Finish. When removal is complete, click Close. Go to Step 2 to run KTSync Setup Wizard.
If there are any problems, please refer to 2.3 Manual Installation .
KTSync Setup Wizard
To install KTSync, follow the steps shown in the images below.
1.
In the KTSync Setup Wizard window, click Next.
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
31
KDC User Manual Installation
2.
In the License Agreement window, select “I Agree” and click Next.
3.
In the KTSync Installation Complete window, click Close and wait for the Device Driver
Installation Wizard.
4.
In the Windows Security window, click Install to complete installation.
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
32
KDC User Manual Installation
Connect KDC to Computer
Using the USB cable included with the KDC or built-in swing out US connector, follow the directions below.
1
. Connect KDC to PC.
2 . Wait until the computer beeps and/or displays the message
Found New Hardware.
Verify COM Port Address
The installed COM Port can be verified in Device Manager.
Android
Download and install aKTSync from the Android Play Store. https://play.google.com/store/apps/details?id=com.koamtac.ktsync&hl
Blackberry
Download and install bKTSync from the Blackberry App World. http://appworld.blackberry.com/webstore/content/16861?lang=en
iPad/iPhone/iPod touch
Download and install iKTSync from the Apple App Store. http://itunes.apple.com/us/app/ktsync/id372916602?mt=8
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
33
KDC User Manual Installation
2.3 Manual Installation
Windows 7/8
1. Insert the KOAMTAC Installation CD into the computer’s disk drive.
2.
Create a directory named KOAMTAC on the computer.
3. Copy XP.Vista.7 directory from the KOAMTAC CD to the KoamTac directory.
XP.Vista.7 directory contains KTSync ® programs for Microsoft ® Windows XP,
Vista, Windows 7, and user manuals.
4. Connect the KDC cable to the ultra mini USB connector on the KDC.
5. Connect the KDC cable to the Type A USB connector on the computer. Wait until the computer beeps and/or displays the message
New Hardware Found
.
The user will be prompted to search for a device driver for the KDC.
6. Browse and select the
KTReader.inf
file from the KoamTac directory (created in Step 2). Follow screen prompts to continue with the device driver installation.
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
34
KDC User Manual O PERATING YOUR KDC
3. Operating your KDC
3.1 Getting Started
Attach Lanyard/Hand Strap to KDC
To prevent possible damage to the KDC, we STRONGLY recommend wearing it around the neck or hand, using the included Lanyard/Hand Strap. In addition, the user should not swing the KDC by its Lanyard/Hand Strap. Impact with another object may cause the KDC to malfunction or become damaged.
To attach the Lanyard:
1
Fit the thin end of the Lanyard through the pillar of the
KDC.
KDC20/30 KDC100/200/300/350/400
2
Guide the thick end of strap through the thin loop.
3
Pull the strap tight to secure.
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
35
KDC User Manual O PERATING YOUR KDC
Charge KDC Battery
Prior to using the KDC, the user should charge its battery by following the below instructions.
1. Connect the KDC cable to the mini USB connector on the KDC.
2. Connect the KDC cable to the Type A USB connector on the computer.
3.
The KDC battery will begin charging. Within a few minutes, the two small LEDs on the front panel will illuminate orange. When the battery is fully charged, the LEDs will illuminate green.
KDC100
2 Hours
KDC20/200
2 Hours
KDC30/250/300
4 Hours
KDC350
5 Hours
Table 2 - Number of hours required to fully charge a KDC Battery
KDC400
5 Hours
Configure KDC
The KDC is designed to meet the data collection requirements of many different industries in a variety of dynamic situations. To deliver the best performance in these diverse environments, the KDC is designed to be configured quickly and easily.
However, to perform at its optimum level, the KDC must be configured properly. Until the user is familiar with the KDC configuration settings, it is recommended that the user
DOES NOT modify the KDC settings. The KDC can be configured by using three different methods, which are explained in Section 3.3 – KDC Menus , Chapter 5 –
Synchronization , and Appendix C/D – Special Barcodes .
CONFIGURATION METHODS FOR THE KDC100/200/250/300/350
KDC Menu
KTSync ® Software
Special Barcodes
Press the Up and DOWN
Buttons simultaneously to access the KDC menu.
Move the menu bar up and down by pressing Up and
Down Buttons.
Select one of the menus by pressing the Scan Button.
Figure 12 - Location of KDC Menu and use of buttons (KDC100/200/250/300)
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
KDC User Manual O PERATING YOUR KDC
Press the Button to access the KDC menu.
Move the menu bar up and down by pressing the
and Buttons, and configure the KDC by pressing the SCAN Button to select a menu.
Figure 13 - Location and use of buttons on a keypad (KDC350)
CONFIGURATION METHODS FOR THE KDC20/30/400
KTSync ® Software
Special Barcodes
36
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
37
KDC User Manual O PERATING YOUR KDC
3.2 Basics
Read barcodes
To read a barcode using the KDC, simply point the KDC at a barcode and press the scan button. Be sure to point the scan engine window at the barcode, not at the user’s face, and make sure to position the light beam on the barcode.
If a barcode has been successfully scanned, the user will hear one short beep and the
LEDs will illuminate green. The scanned barcode data will be displayed on the KDC screen, along with the scan time and battery level.
Depending on the configuration of the
KDC, other information may also be displayed.
Figure 14 - KDC Display
Figure 15 - Scanning barcodes using KTSync
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
38
KDC User Manual O PERATING YOUR KDC
If scanning was unsuccessful, the user will hear two short beeps, the LEDs will illuminate red, and the message
Failed reading…
will display. If this is the case, the user should point the KDC at the barcode and press the scan button while trying the following suggestions:
Modify the angle of the KDC in relation to the barcode, making the angle more wide or narrow as needed.
Modify the distance between the barcode and the KDC, moving closer or further away as needed.
Check the option settings defined in the KDC menu section and change options as needed.
Check to see that the barcode’s width does not exceed the light beam’s width, and vice versa.
Read barcodes with GPS coordinates (KDC350G)
The KDC350G can add GPS coordinates after the barcode data. To do so, the user can follow the below instructions.
Note
Because of the characteristics of GPS, this function is only available when outdoors.
1. Go to GPS Power in GPS Menu and select Enable.
2. Check to see if the KDC is successfully acquiring GPS data by selecting Acquire
Test in GPS Menu.
When the user selects the Acquire Test, an within 90 seconds of acquiring GPS signal.
‘Acquiring’
message will appear on the screen. If this is the first test, check to make sure the ‘Acquired’ message appears
3. Go to System Config in the KDC Menu and select GPS data in Display Format.
4.
After finishing the configuration, scan a barcode as explained in 3.2.1 Reading
Barcodes.
When the user has successfully scanned a barocde, the barcode data and GPS coordinate will appear on the KDC screen.
For more information, refer to 3.3 Menu - GPS Config (350G).
Read NFC Tag (KDC350N/400N)
1 . Enable the NFC Power option in the NFC Config menu.
2 . Touch the NFC tag to the back of the KDC350N/450N case, and make sure the tag and case are within 5cm of each other.
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
KDC User Manual O PERATING YOUR KDC
39
Figure 16 - Location for reading NFC Tag
3.
The KDC will show the NFC tag UID and the user will hear a short beep if it has been read successfully.
4.
The KDC350N/450N can process “Mifare Ultra Light” and “Mifare Ultra Light C” data only. Other types of tags should be processed in the host application.
Read HF RFID Tag (KDC450)
The KDC450 can virtually read any ISO/IEC 14443 A or B compliant smartcards, or ISO/IEC
15693 compliant HF RFID tags.
To read a HF RFID tag, touch the RFID card to the back of the KDC450 case, and make sure the tag and case are within 5cm of each other. The user will hear a short beep if it has been read successfully.
Input data by using a keypad (KDC350)
The KDC350 allows users to input barcode data by using its keypad. The user can switch between Num mode and Abc mode by using the Mode button.
To switch between uppercase and lowercase letters, the user can press the Shift button while in Abc mode. To save the data input, press the Enter or SCAN button. To cancel the data input, press the Menu button. Refer to 1.4 Input data by using a keypad (KDC350) for more detailed information about the process.
Synchronizing data to the host device
Use the KTSync ® program to synchronize barcode data from the KDC to the host device.
Please refer to Chapter 6. Synchronization for details.
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
40
KDC User Manual O PERATING YOUR KDC
3.3 KDC Menu
Options Top
Menu
KDC
Mode
Sub
Menu
Normal
Applicati on
View
Data
Set
Barcode s
(20/100
/200/25
0
/350L/K
DC410/
KDC415
)
Set
Barcode s
(300/35
0C/420/
425/450
)
2D
1D
Symbolo gy
View/Del ete
EAN13
EAN8
UPCA
UPCE
CODE39
ITF14
CODE128
I2of5
CODABA
R
GS1-128
CODE93
CODE35
Bookland
EAN
EAN13wit hAddon
EAN8with
Addon
UPCAwit hAddon
UPCEwith
Addon
Code 11
Code 32
Code 39
Code 93
Code 128
EAN-8
EAN-13
GS1 Composit
I2of5
Matrix 2of5
MSI
Plessey
PosiCode
GS1 Omni
GS1 Limited
GS1 Expanded
S2of5 Ind
S2of5 IATA
TCL39
Telepen
Trioptic
UPCA
UPCE0
UPCE1
AztecCode
Enabled/Disabled
Enabled/Disabled
Enabled/Disabled
Enabled/Disabled
Enabled/Disabled
Enabled/Disabled
Enabled/Disabled
Enabled/Disabled
Enabled/Disabled
Enabled/Disabled
Enabled/Disabled
Enabled/Disabled
Enabled/Disabled
Enabled/Disabled
Enabled/Disabled
Enabled/Disabled
Enabled/Disabled
Codabar
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
KDC20 KDC100 KDC200
Default
N/A
N/A
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Default
Custom
Applicati on
View/Del ete Data
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Default
Custom
Applicati on
View/Del ete Data
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Default
Custom
Applicati on
View/Del ete Data
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
KDC250 KDC300
Default
Custom
Applicati on
View/Del ete Data
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
KDC350L
(opticon)
Default
Custom
Applicatio n
View/Dele te Data
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
KDC350L
(N4303/SE9
60)
Default
Custom
Application
View/Delete
Data
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
KDC350
C
Default
Custom
Applicati on
View/Del ete Data
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Enabled
Enabled
Enabled
Disabled
Enabled
Enabled
Enabled
Disabled
Enabled
Enabled
Enabled
Disabled
Enabled
Enabled
Enabled
Disabled
N/A
N/A
N/A
N/A
Enabled
Enabled
Enabled
Disabled
Enabled
Enabled
Enabled
Disabled
N/A
N/A
N/A
N/A
Disabled Disabled
Disabled Disabled
Disabled Disabled
Disabled Disabled
Disabled Disabled Disabled Disabled
Disabled Disabled Disabled Disabled
N/A N/A N/A N/A
N/A
N/A
N/A
N/A
Enabled
Disabled
Disabled
Disabled
Disabled
N/A
Disabled
Disabled
Disabled
Disabled
N/A
N/A
N/A
N/A
N/A
Enabled
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
41
KDC User Manual O PERATING YOUR KDC
Barcode
Options
(20/100
/200/25
0
/350L/4
10/415)
OCR
CodaBar_
NoStartSt opChars
UPCE_as_
UPCA
EAN8_as_
EAN13
UPCE_as_
EAN13
ReturnCh eckDigit
VerifyChe ckDigit
UPCA_as_
EAN13
I2of5_Ver ifyCheck
Digit
Code39_
VerifyChe ckDigit
I2of5_Ret urnCheck
Digit
Code39_
ReturnCh eckDigit
UPCE_Ret urnCheck
Digit
UPCA_Re turnChec kDigit
EAN8_Ret urnCheck
Symbolo gy
Postal
Codes
Enabled/Disabled
Enabled/Disabled
Enabled/Disabled
Enabled/Disabled
Enabled/Disabled
Enabled/Disabled
AztecRunes
CodablockF
Code16K
Code49
DataMatrix
MaxiCode
MicroPDF
PDF417
QRCode
HanXin Code
Postnet
PlanetCode
UK Post
Canada Post
Kix Post
Australia Post
Japan Post
China Post
Korea Post
OCR Off
OCR A
OCR B
OCR USC
OCR MICR
OCR SEMI
Enabled/Disabled
Enabled/Disabled
Enabled/Disabled
Enabled/Disabled
Enabled/Disabled
Enabled/Disabled
Enabled/Disabled
Enabled/Disabled
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Disabled
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Disabled
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Disabled
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Disabled Disabled Disabled Disabled
Disabled Disabled Disabled Disabled
Disabled Disabled Disabled Disabled
Disabled Disabled Disabled Disabled
Disabled Disabled Disabled Disabled
Disabled Disabled Disabled Disabled
Disabled Disabled Disabled Disabled
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Disabled
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Disabled Disabled Disabled Disabled
Disabled Disabled Disabled Disabled
Disabled Disabled Disabled Disabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Disabled
Disabled
Disabled
Disabled
Disabled
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Disabled
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Disabled
Disabled
Disabled
Disabled
Disabled
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Disabled
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Enabled
Enabled
Enabled
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
42
KDC User Manual O PERATING YOUR KDC
Barcode
Options
(300/35
0C/420/
425/450
)
Digit
EAN13_R eturnChe ckDigit
Codabar
Enabled/Disabled
Code39
UPCE
Tx
StartStop(Enabled/Dis abled)
Check
Digit(DoNotVerify/Ver fyDONotTX/VerifyDoT x)
Concatenate(Disabled
/Enabled/Required)
Tx
StartStop(Enabled/Dis abled)
Check
Digit(DoNotVerify/Ver fyDONotTX/VerifyDoT x)
Append(Enabled/Disa bled)
I2of5
Full
ASCII(Enabled/Disable d)
Check
Digit(DoNotVerify/Ver fyDONotTX/VerifyDoT
Code11 x)
Check Digit(2 digits/1 digit)
Code128 Concatenate(Disabled
Telepen
UPCA
/Enabled)
Output(Original/AIM)
VerifyChkDgt(Enabled
/Disabled)
NumberSys(Enabled/
Disabled)
2DgtAddenda(Enable d/Disabled)
5DgtAddenda(Enable d/Disabled)
Req.
Addenda(Enabled/Dis abled)
Sep.
Addenda(Enabled/Dis abled)
Coupon
Code(Enabled/Disable d)
Expand(Enabled/Disa bled)
Req.
Addenda(Enabled/Dis abled)
Sep.
Addenda(Enabled/Dis abled)
Check
Digit(Enabled/Disable d)
NumberSys(Enabled/
Disabled)
Enabled
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Enabled Enabled
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Enabled
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Disabled
DoNotVe rify
Enabled
Disabled
DoNotVe rify
Disabled
Disabled
DoNotVe rify
2 digits
Disabled
AIM
Enabled
Enabled
Disabled
Disabled
Disabled
Enabled
Enabled
Disabled
Disabled
Enabled
Enabled
Enabled
Enabled
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Enabled
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Disabled
DoNotVe rify
Enabled
Disabled
DoNotVe rify
Disabled
Disabled
DoNotVe rify
Enabled
Enabled
Disabled
Disabled
Enabled
Enabled
Enabled
2 digits
Disabled
AIM
Enabled
Enabled
Disabled
Disabled
Disabled
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
43
KDC User Manual O PERATING YOUR KDC
Scan
Options
EAN-13
EAN-8
MSI
PosiCode
GS1
PostNet
PlanetCo de
Scan Ang le
Filter
Time Out
2DgtAddenda(Enable d/Disabled)
5DgtAddenda(Enable d/Disabled)
VerifyChkDgt(Enabled
/Disabled)
2DgtAddenda(Enable d/Disabled)
5DgtAddenda(Enable d/Disabled)
Req.
Addenda(Enabled/Dis abled)
Sep.
Addenda(Enabled/Dis abled)
ISBN
Trans.(Enabled/Disabl ed)
VerifyChkDgt(Enabled
/Disabled)
2DgtAddenda(Enable d/Disabled)
5DgtAddenda(Enable d/Disabled)
Req.
Addenda(Enabled/Dis abled)
Sep.
Addenda(Enabled/Dis abled)
Tx
CheckChar(Enabled/D isabled)
A and B/A&B
LimitedA/A&B
LimitedB
UPCEAN
Ver.(Enabled/Disabled
)
GS1 Emulation(No
Emulate/GS1 128
Emul/GS1 Emulate)
Tx
CheckChar(Enabled/D isabled)
Tx
CheckChar(Enabled/D isabled)
Narrow/Wide
Normal/High
.5 seconds to 10 seconds
2 to 36 characters
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Wide
Normal
2 second(s
)
4 chars Min.
Barcode
Length
Min.
Barcode
Length
Security L evel
Image
2 to 48 characters
1 to 4 level
Enabled/Disabled
N/A
2 level
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Wide
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Wide
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Wide
A&B
LimitedB
Disabled
No
Emulate
Normal
2 second(s
)
4 chars
Normal
2 second(s
)
4 chars
Normal
2 second(s
)
4 chars
N/A
2 second(s
)
N/A
N/A
2 level
N/A
N/A
2 level
N/A
N/A
2 level
N/A
Disabled
Disabled
Enabled
Disabled
Disabled
Disabled
Enabled
Disabled
Enabled
Disabled
Disabled
Disabled
Enabled
Disabled
Disabled
Disabled
N/A
4 chars
N/A
Disabled
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Wide
A&B
LimitedB
Disabled
No
Emulate
Normal
2 second(s)
4 chars
N/A
2 second(s)
4 chars
N/A
2 second(s
)
N/A
N/A
2 level
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
2 level
N/A
Disabled
Disabled
Enabled
Disabled
Disabled
Disabled
Enabled
Disabled
Enabled
Disabled
Disabled
Disabled
Enabled
Disabled
Disabled
Disabled
N/A
4 chars
N/A
Disabled
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
44
KDC User Manual O PERATING YOUR KDC
Data
Process
BT
Config
Capture
Auto
Trigger
Reread
Delay
Finger
Trigger
Partial
Display
Wedge /
Store
Chk
Duplicate
Enter Key
Connect
Device
(Non Mfi mode)
Connect
Device
(Mfi mode )
Auto
Connect
Auto
Reconnec t
Auto
Enabled/Disabled
Continuous, Short,
Medium, Long, Extra
Long
Enabled/Disabled
Start Position
No. of Char(s)
Action
Wedge Only
HID iOS
SPP2.0
HID normal
SPP
Enabled
1
Data For mat
Data
Editor/Pr efix
Data
Editor/Su ffix
Data
Editor/AI
M ID
Data
Editor/Pa rtial Data
Handsha ke
Terminat or
Wedge & Store
Always
Store Only
Save if Sent
Save if Not Sent
Barcode only
Packet Data
Delete
Delete
None/In Prefix/In
Suffix
Start Position
No. of Char(s)
Action
Enable/Disabled
None, CR, LF, CR+LF,
Tab, Right Arrow, Left
Arrow,Down Arrow,
Up Arrow
Enabled/Disabled
Default
Default
Delete
Delete
None
1
0 chars
Select
Disabled
CR+LF
Disabled
Enabled/Disabled
SPP iPhone
Enabled/Disabled
Enabled/Disabled
Enabled/Disabled
Disabled
Medium
0 chars
Select
N/A
Default
Default
Disabled
Disabled
Disabled
Disabled Disabled Disabled Disabled
Medium
Enabled
1
0 chars
Select
Default
Default
Delete
Delete
None
1
0 chars
Select
Disabled
CR+LF
Disabled
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Medium
Enabled
1
0 chars
Select
Default
Default
Delete
Delete
None
1
0 chars
Select
Disabled
CR+LF
Disabled
N/A
Default
Default
Disabled
Disabled
Disabled
Medium
Enabled
1
0 chars
Select
Default
Default
Delete
Delete
None
1
0 chars
Select
Disabled
CR+LF
Disabled
N/A
Default
Default
Disabled
Disabled
Disabled
Medium
N/A
1
0 chars
Select
Default
Default
Delete
Delete
None
1
0 chars
Select
Disabled
CR+LF
Disabled
N/A
Default
Default
Disabled
Disabled
Disabled
Disabled
Medium
Enabled
1
0 chars
Select
Default
Default
Delete
Delete
None
1
0 chars
Select
Disabled
CR+LF
Disabled
Disabled
Default
Default
Disabled
Disabled
Disabled
Disabled
Medium
Enabled
1
0 chars
Select
Default
Default
Delete
Delete
None
1
0 chars
Select
Disabled
CR+LF
Disabled
Medium
Default
Delete
N/A
1
0 chars
Select
Default
Delete
None
1
0 chars
Select
Disabled
CR+LF
Disabled
Disabled
Default
Disabled
Disabled
Default
Default
Disabled
Disabled
Disabled
Default
Disabled
Disabled
Disabled
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
45
KDC User Manual O PERATING YOUR KDC
USB
Config-
USB
Serial
Mode
(M model)
BT
Service
Auto
Power
Off/Powe r Off
Time
PowerOff
Msg
MAC
Address
BT FW
Version
Wakeup
Nulls
Connect
Alert
BT
Toggle
Power
On
Auto
Power
On/Powe r On
Time
Auto
Power
Off
Auto
Power
Off/Beep
Warning
Disconne ctBtn
HID
AutoLock
HID
Keyboard
HID
Delay/Init ial
HID
Delay/Int er char
HID Ctrl
Char
Power disabled, 1sec to
10second(s)
Enabled/Disabled
Enabled/Disabled
1 to 30 minutes
Enabled/Disabled
12 Characters v1.2.xrt Bluetooth Firmware to |
Bluetooth MAC
Address
Version
Enabled/Disabled
Enabled/Disabled
Enabled/Disabled
Enabled/Disabled disabledd,1,2,3,4,5,10,
15 minutes
US,German,French,Ital ian,Spanish
Disabled, 1,2,3,5,10 secs
Disabled,10, 20, 30,
50, 100msec
Disabled,
Alt+Numpad,
^+Character, Replace
Enabled/Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Enabled
Enabled
1 minutes
US
Disabled
Disabled
Disabled
Enabled
Pairing
Discoveri ng
Connecti ng to
HID Sync
USB
Mode
Pairing neighboring Bluetooth devices
Discovering neighboring Bluetooth devices
View Connect to Bluetooth device
USB Serial/USB Disk USB
Serial
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
USB
Serial
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Disabled Disabled Disabled Disabled
Disabled Disabled Disabled Disabled
Disabled Disabled Disabled Disabled
Disabled Disabled Disabled Disabled
Disabled Disabled Disabled
Disabled Disabled Disabled
Disabled Disabled Disabled
Enabled Enabled Enabled
Disabled
Disabled
Disabled
Enabled
Enabled Enabled Enabled Enabled
USB
Serial
USB
Serial
USB
Serial
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Enabled
Disabled
Disabled
Enabled
USB Serial USB Serial
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Enabled
USB
Serial
Disabled
Disabled
Disabled
Enabled
Enabled Enabled Enabled Enabled
1 minutes
US
1 minutes
US
1 minutes
US
1 minutes
US
Disabled Disabled Disabled Disabled
Enabled
1 minutes
US
Disabled
Enabled
1 minutes
US
Disabled
Disabled Disabled Disabled Disabled
Disabled Disabled Disabled Disabled
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
46
KDC User Manual O PERATING YOUR KDC
USB
Config-
USB
Disk
Mode
(M model)
USB
Mode
Disk
Format
Data
Format
NFC
Config
(N model)
NFC
Power
GPS
Config
(G model)
Data
Format
UID Only
GPS
Power
System
Config
Memory
Size(3.0 only)
Memory
Status
Reset Me mory
Power
Mode
Bypass
Data
Acqurie
Test
Reset
GPS
Auto
Erase
Sleep Ti meout
Date /
Time
Battery
Version
Button L ock
Beep
Alert
/Beep So und
Beep
Alert
/Power
On Beep
Beep
USB Serial/USB Disk
Format KDC USB Disk
Data,DataTime,
DataType,DataTimeTy pe
Enabled/Disabled
Barcode only/Packet
Data
Enabled/Disabled
Enabled/Disabled
Normal/Power Save
Enabled/Disabled
0.5/3.5, 1/3, 2/2, 3/1,
4/0
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
No. of Stored Barcodes
Free Memory Available
Memory(Empties Data)
Application Memory
BT Registry(KDC100 Not use)
Enabled/Disabled
Disabled, 1sec to
10minute(s)
YYYY:MM:DD &
HH:MM:SS
Enabled/Disabled
Enabled/Disabled
Enabled/Disabled
Enabled/Disabled
Disabled
5 second(s
)
% of Battery Charge Available
Firmware Version & Serial No.
N/A
Enabled
Enabled
Enabled
USB Disk
Data
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
0.5M/3.5
M
Disabled
5 second(s
)
Disabled
Enabled
Enabled
Enabled
USB Disk
Data
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
0.5M/3.5
M
Disabled
5 second(s
)
Disabled
Enabled
Enabled
Enabled
USB Disk
Data
N/A
N/A
N/A
Disabled
Normal
Disabled
0.5M/3.5
M
Disabled
5 second(s
)
Disabled
Enabled
Enabled
Enabled
USB Disk
Data
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
0.5M/3.5
M
Disabled
5 second(s
)
Disabled
Enabled
Enabled
Enabled
USB Disk
Data
Enabled
Packet
Data
Disabled
Disabled
Normal
Disabled
0.5M/3.5
M
Disabled
5 second(s)
Disabled
Enabled
Enabled
Enabled
USB Disk
Data
Enabled
Packet Data
Disabled
Disabled
Packet
Data
Disabled
Disabled
Normal
Disabled
0.5M/3.5M
Disabled
5 second(s)
Disabled
Enabled
Enabled
Enabled
USB Disk
Data
Enabled
Normal
Disabled
0.5M/3.5
M
5 second(s
)
Disabled
Disabled
Enabled
Enabled
Enabled
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
47
KDC User Manual O PERATING YOUR KDC
MSR
Config
Alert
/Beep On
Connect
Beep
Alert
/Beep On
Scan
Beep
Volume
Mfi
( i-chip installed)
Auto Exit
Port
Status
Display
Format
Enabled/Disabled
Low/High
Enabled/Disabled
Enabled/Disabled
Enabled/Disabled
Enabled
Low
Enabled
N/A
N/A
Menu
Barcode
Scrolling
Brightnes s
Factory
Default
Time & Battery /
Type & Time / Type
& Battery / Memory
Status / GPS
Data(KDC250 only)/Barcode Only
Enabled/Disabled
Enabled/Disabled
1 to 15 level(8 level)
Restores Default Settings
Data For mat
Use
Track1
Use
Track2
Use
Track3
Beep on error reading
MSR Data Only
Packet Data
Enabled/Disabled
Encrypt
MSR
Data
AES Key
Length
Enabled/Disabled
128bit/192bit/256bit
Card
Type
Track
Separator
ISO/OTHER 1/AAMVA
None/Space/Comma/
Semicolon/CR/LF/CR
&LF/Tab
Attach Start/End Sentinel
Partial Data Start Position
Partial
Data
Action
Partial Data Length
Erase/Select
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Enabled
Low
N/A
Enabled
Enabled
Time &
Battery
N/A
Enabled
8 level
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Enabled
Low
Enabled
Enabled
Enabled
Time &
Battery
N/A
Enabled
8 level
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Enabled Enabled
Low
Enabled Enabled
Enabled
Enabled
Enabled
Enabled
Time &
Battery
N/A
Time &
Battery
Disabled
Enabled
8 level
Enabled
8 level
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Low
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Enabled
Low
Enabled
Enabled
Enabled
Time &
Battery
N/A
Enabled
8 level
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Enabled
Low
Enabled
Enabled
Enabled
Time &
Battery
N/A
Enabled
8 level
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Enabled
Low
Enabled
Enabled
Enabled
Time &
Battery
Disabled
Enabled
8 level
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
48
KDC User Manual O PERATING YOUR KDC
Top
Menu
KDC
Mode
View
Data
Set
Barcode s
(20/100
/200/25
0
/350L/K
DC410/
KDC415
)
Set
Barcode s
(300/35
0C/420/
425/450
)
Sub Menu
Normal
Application
View/Delete
Options KDC410
Default
N/A
N/A
KDC415
Default
N/A
N/A
EAN13
EAN8
UPCA
UPCE
CODE39
ITF14
CODE128
I2of5
CODABAR
GS1-128
CODE93
CODE35
BooklandEAN
Codabar
Code 11
Code 32
Code 39
Code 93
Code 128
EAN-8
EAN-13
GS1 Composit
I2of5
Matrix 2of5
MSI
Plessey
PosiCode
GS1 Omni
GS1 Limited
GS1 Expanded
S2of5 Ind
S2of5 IATA
TCL39
Telepen
Trioptic
UPCA
Enabled/Disable d
Enabled/Disable d
Enabled/Disable d
Enabled/Disable d
Enabled/Disable d
Enabled/Disable d
Enabled/Disable d
Enabled/Disable d
Enabled/Disable d
Enabled/Disable d
Enabled/Disable d
Enabled/Disable d
Enabled/Disable d
Enabled/Disable d
Enabled/Disable d
Enabled/Disable d
Enabled/Disable d
EAN13withAdd on
EAN8withAddo n
UPCAwithAddo n
UPCEwithAddo n
1D Symbology
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Disabled Disabled
Disabled
Disabled
Disabled
Disabled
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Disabled
Disabled
Disabled
Disabled
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
KDC420 KDC425
Default
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Default
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
KDC430 KDC450
Default
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Default
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
49
KDC User Manual O PERATING YOUR KDC
Barcode
Options
(20/100
/200/25
0
/350L/4
10/415)
Barcode
Options
(300/35
0C/420/
425/450
2D Symbology
Postal Codes
OCR OCR Off
OCR A
OCR B
OCR USC
OCR MICR
OCR SEMI
CodaBar_NoSta rtStopChars
Enabled/Disable d
UPCE_as_UPCA Enabled/Disable d
EAN8_as_EAN1
3
UPCE_as_EAN1
3
ReturnCheckDi git
VerifyCheckDig it
UPCA_as_EAN1
3
I2of5_VerifyChe ckDigit
Code39_Verify
CheckDigit
I2of5_ReturnCh eckDigit
Code39_Return
CheckDigit
Enabled/Disable d
Enabled/Disable d
Enabled/Disable d
Enabled/Disable d
Enabled/Disable d
Enabled/Disable d
Enabled/Disable d
Enabled/Disable d
Enabled/Disable d
UPCE_ReturnC heckDigit
UPCA_ReturnC heckDigit
EAN8_ReturnC heckDigit
EAN13_Return
CheckDigit
Codabar
Enabled/Disable d
Enabled/Disable d
Enabled/Disable d
Enabled/Disable d
Tx
StartStop(Enabl ed/Disabled)
Check
Digit(DoNotVeri
UPCE0
UPCE1
AztecCode
AztecRunes
CodablockF
Code16K
Code49
DataMatrix
MaxiCode
MicroPDF
PDF417
QRCode
HanXin Code
Postnet
PlanetCode
UK Post
Canada Post
Kix Post
Australia Post
Japan Post
China Post
Korea Post
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Disabled
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Disabled
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enable
Disabled
Disabled
Disabled
Disabled
Disabled
N/A
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Disabled
Disabled
Disabled
Disabled
Disabled
N/A
Disabled Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Enabled
Enabled
Enabled
Enabled
N/A
N/A
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Enabled
Enabled
Enabled
Enabled
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Disabled
DoNotVe rify
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Disabled
DoNotVe rify
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A DoNotVe rify
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Disabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enable
Disabled
Disabled
Disabled
Disabled
Disabled
N/A
N/A
N/A
N/A
N/A
N/A
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
50
KDC User Manual O PERATING YOUR KDC
)
Code39
I2of5
Code11
Code128
Telepen
UPCA
UPCE
Req.
Addenda(Enable d/Disabled)
Sep.
Addenda(Enable d/Disabled)
Coupon
Code(Enabled/D isabled)
Expand(Enabled
/Disabled)
Req.
Addenda(Enable d/Disabled)
Sep.
Addenda(Enable d/Disabled)
Check
Digit(Enabled/Di sabled)
NumberSys(Ena bled/Disabled)
2DgtAddenda(E nabled/Disabled
)
5DgtAddenda(E nabled/Disabled fy/VerfyDONotT
X/VerifyDoTx)
Concatenate(Dis abled/Enabled/
Required)
Tx
StartStop(Enabl ed/Disabled)
Check
Digit(DoNotVeri fy/VerfyDONotT
X/VerifyDoTx)
Append(Enable d/Disabled)
Full
ASCII(Enabled/D isabled)
Check
Digit(DoNotVeri fy/VerfyDONotT
X/VerifyDoTx)
Check Digit(2 digits/1 digit)
Concatenate(Dis abled/Enabled)
Output(Original
/AIM)
VerifyChkDgt(En abled/Disabled)
NumberSys(Ena bled/Disabled)
2DgtAddenda(E nabled/Disabled
)
5DgtAddenda(E nabled/Disabled
)
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A Enabled Enabled N/A Enabled
N/A Disabled Disabled N/A Disabled
N/A DoNotVe rify
DoNotVe rify
N/A DoNotVe rify
N/A
N/A
Disabled Disabled
Disabled Disabled
N/A
N/A
Disabled
Disabled
N/A DoNotVe rify
DoNotVe rify
N/A DoNotVe rify
N/A
N/A
N/A
N/A
N/A
N/A
2 digits 2 digits
Disabled Disabled
AIM AIM
Enabled Enabled
Enabled Enabled
Disabled Disabled
N/A
N/A
N/A
N/A
N/A
N/A
2 digits
Disabled
AIM
Enabled
Enabled
Disabled
N/A Disabled Disabled N/A Disabled
N/A Disabled Disabled N/A Disabled
N/A Enabled Enabled N/A Enabled
N/A Enabled Enabled N/A Enabled
N/A
N/A
Disabled Disabled
Disabled Disabled
N/A
N/A
Disabled
Disabled
N/A Enabled Enabled N/A Enabled
N/A Enabled Enabled N/A Enabled
N/A
N/A
Enabled Enabled
Disabled Disabled
N/A
N/A
Enabled
Disabled
N/A Disabled Disabled N/A Disabled
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
51
KDC User Manual O PERATING YOUR KDC
Scan
Options
EAN-13
EAN-8
MSI
PosiCode
GS1
PostNet
PlanetCode
Scan Angle
Filter
Time Out
)
A and B/A&B
LimitedA/A&B
LimitedB
UPCEAN
Ver.(Enabled/Di sabled)
GS1
Emulation(No
Emulate/GS1
128 Emul/GS1
Emulate)
Tx
CheckChar(Enab led/Disabled)
Tx
CheckChar(Enab led/Disabled)
Narrow/Wide
Normal/High
.5 seconds to
10 seconds
VerifyChkDgt(En abled/Disabled)
2DgtAddenda(E nabled/Disabled
)
5DgtAddenda(E nabled/Disabled
)
Req.
Addenda(Enable d/Disabled)
Sep.
Addenda(Enable d/Disabled)
ISBN
Trans.(Enabled/
Disabled)
VerifyChkDgt(En abled/Disabled)
2DgtAddenda(E nabled/Disabled
)
5DgtAddenda(E nabled/Disabled
)
Req.
Addenda(Enable d/Disabled)
Sep.
Addenda(Enable d/Disabled)
Tx
CheckChar(Enab led/Disabled)
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Wide
Normal
2 second(s
)
4 chars Min. Barcode
Length
Min. Barcode
Length
2 to 36 characters
2 to 48 characters
Security Level 1 to 4 level
Image Capture Enabled/Disable d
N/A
2 level
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Wide
Normal
2 second(s
)
4 chars
N/A
N/A
2 second(s
)
N/A
N/A
2 level
N/A
Enabled
Disabled
Disabled
Disabled
Enabled
Disabled
Enabled
Disabled
Disabled
Disabled
Enabled
Disabled
A&B
LimitedB
Disabled
No
Emulate
Disabled
Disabled
4 chars
N/A
Disabled
Enabled
Disabled
Disabled
Disabled
Enabled
Disabled
Enabled
Disabled
Disabled
Disabled
Enabled
Disabled
A&B
LimitedB
Disabled
No
Emulate
Disabled
Disabled
N/A
N/A
2 second(s
)
N/A
4 chars
N/A
Disabled
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Enabled
Disabled
Disabled
Disabled
Enabled
Disabled
Enabled
Disabled
Disabled
Disabled
Enabled
Disabled
A&B
LimitedB
Disabled
No
Emulate
Disabled
Disabled
N/A
N/A
2 second(s
)
N/A
4 chars
N/A
Disabled
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
52
KDC User Manual O PERATING YOUR KDC
Data
Process
BT
Config
Auto Trigger
Reread Delay
Finger Trigger
Partial Display
Wedge / Store
Enabled/Disable d
Continuous,
Short, Medium,
Long, Extra
Long
Enabled/Disable d
Start Position
No. of Char(s)
Action
Wedge Only
Wedge & Store
Always
Disabled
Medium
N/A
N/A
N/A
N/A
Default
Data Format
Data
Editor/Prefix
Data
Editor/Suffix
Data
Editor/AIM ID
Data
Editor/Partial
Data
Handshake
Terminator
Store Only
Save if Sent
Save if Not Sent
Barcode only
Packet Data
Delete
Delete
None/In
Prefix/In Suffix
Start Position
Default
Delete
Delete
None
1
Chk Duplicate
Enter Key
ConnectDevice
(Non Mfi mode)
ConnectDevice
(Mfi mode )
HID iOS
SPP2.0
HID normal
SPP
Auto Connect
Auto
Reconnect iPhone
Enabled/Disable d
Enabled/Disable d
Auto Power On Enabled/Disable d
Auto Power
On/Power On disabled, 1sec to 10second(s)
Time
Auto Power
Off
Auto Power
Off/Beep
Enabled/Disable d
Enabled/Disable d
No. of Char(s) 0 chars
Action Select
Enable/Disabled Disabled
CR+LF None, CR, LF,
CR+LF, Tab,
Right Arrow,
Left
Arrow,Down
Arrow, Up
Arrow
Enabled/Disable d
Enabled/Disable d
Disabled
N/A
SPP Default
Default
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Medium
N/A
N/A
N/A
N/A
Default
Default
Delete
Delete
None
1
0 chars
Select
Disabled
CR+LF
Disabled
N/A
Default
Default
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled Disabled
Medium
N/A
N/A
N/A
N/A
Default
Default
Delete
Delete
None
1
Medium
N/A
N/A
N/A
N/A
Default
Default
Delete
Delete
None
1
0 chars
Select
Disabled
CR+LF
0 chars
Select
Disabled
CR+LF
Disabled Disabled
N/A
Default
Default
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
N/A
Default
Default
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
N/A
N/A
N/A
N/A
N/A
N/A
Default
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
CR+LF
N/A
N/A
Default
Default
Disabled
Disabled
Medium
N/A
N/A
N/A
N/A
Default
Default
Delete
Delete
None
1
0 chars
Select
Disabled
CR+LF
Disabled
N/A
Default
Default
Disabled
Disabled Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
53
KDC User Manual O PERATING YOUR KDC
BT
Service
USB
Config-
USB
Serial
Mode
(M model)
USB
Config-
USB
Disk
Mode
(M model)
NFC
Config
(N model)
GPS
Config
(G model)
Warning
Auto Power
Off/Power Off
1 to 30 minutes
Time
PowerOff Msg Enabled/Disable
Disabled
Disabled
MAC Address
Disabled Disabled
Disabled Disabled d
12 Characters Bluetooth MAC Address
BT FW Version
Wakeup Nulls
Connect Alert
BT Toggle
DisconnectBtn
HID AutoLock
HID Keyboard
HID
Delay/Initial
HID
Delay/Inter char
HID Ctrl Char d v1.2.xrt Bluetooth Firmware Version
Enabled/Disable
Enabled/Disable d
Enabled/Disable d
Enabled/Disable d disabledd,1,2,3,
4,5,10,15 minutes
US,German,Fren ch,Italian,Spanis h
Disabled,
1,2,3,5,10 secs
Disabled,10, 20,
30, 50, 100msec
Disabled
N/A
Enabled
Disabled
1 minutes
US
Disabled
Disabled
Disabled
N/A
Enabled
Disabled
1 minutes
US
Disabled
Disabled
Disabled
N/A
Enabled
Disabled
1 minutes
US
Disabled
Disabled
Power
Pairing
Discovering
Disabled,
Alt+Numpad,
^+Character,
Replace to |
Disabled Disabled Disabled
Enabled/Disable d
Enabled Enabled
Pairing neighboring Bluetooth devices
Enabled
Discovering neighboring Bluetooth devices
Connecting to
HID Sync
USB Mode
View Connect to Bluetooth device
USB Serial/USB
Disk
USB
Serial
USB
Serial
USB
Serial
Disabled Disabled
Disabled
Disabled
N/A
Enabled
Disabled
1 minutes
US
Disabled
Disabled
Disabled
Enabled
USB
Serial
Disabled
Disabled
N/A
Enabled
Disabled
1 minutes
US
Disabled
Disabled
Disabled
Enabled
USB
Serial
Disabled
Disabled
Disabled
N/A
Enabled
Disabled
1 minutes
US
Disabled
Disabled
Disabled
Enabled
USB
Serial
USB Mode
Disk Format
Data Format
NFC Power
Data Format
UID Only
GPS Power
Power Mode
USB Serial/USB
Disk
Format KDC
USB Disk
Data,DataTime,
DataType,DataTi meType
Enabled/Disable d
Barcode only/Packet
Data
Enabled/Disable d
Enabled/Disable d
Normal/Power
Save
N/A
N/A
N/A
Enabled
Packet
Data
Disabled Disabled
N/A
N/A
N/A
N/A
N/A
Enabled
Packet
Data
N/A
N/A
N/A
N/A
N/A
Enabled
Packet
Data
N/A
N/A
N/A
N/A
N/A
Enabled
Packet
Data
Disabled Disabled
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
54
KDC User Manual O PERATING YOUR KDC
System
Config
MSR
Config
Bypass Data
Acqurie Test
Reset GPS
Memory Size(3.
0 only)
Memory Status
Reset Memory
Auto Erase
Sleep Timeout
Date / Time
Battery
Enabled/Disable d
N/A
N/A
N/A
0.5/3.5, 1/3, 2/2,
3/1, 4/0
N/A
No. of Stored Barcodes
N/A
N/A
N/A
N/A
Free Memory Available
Memory(Empties Data)
Application
Memory
N/A
BT
Registry(KDC10
0 Not use)
N/A
Enabled/Disable d
Disabled, 1sec to 10minute(s)
Enabled
5 second(s
)
N/A
N/A
Enabled
5 second(s
)
YYYY:MM:DD &
HH:MM:SS
% of Battery Charge Available
Version
Button Lock
Beep Alert
/Beep Sound
Beep Alert
/Power On
Beep
Beep Alert
/Beep On
Connect
Beep Alert
/Beep On Scan
Beep Volume
Mfi
( i-chip installed)
Auto Exit
Firmware Version & Serial No.
Enabled/Disable d
Enabled/Disable d
Low/High
Enabled/Disable d
N/A
Enabled
Enabled/Disabled
Enabled/Disabled
Enabled/Disabled
Low
Enabled
N/A
Enabled
Low
Enabled
Port Status
Display Format
Enabled/Disable d
Enabled/Disable d
Time & Battery
/ Type & Time /
Type & Battery
/ Memory
Status / GPS
Data(KDC250 only)/Barcode
Only
N/A
N/A
N/A
N/A
N/A
N/A
Menu Barcode Enabled/Disable d
Scrolling
Brightness
Factory Default
N/A
Enabled/Disable d
1 to 15 level(8 level)
N/A
N/A
Restores Default Settings
Data Format
Use Track1
Use Track2
Use Track3
Beep on error
MSR Data Only
Packet Data
Enabled/Disable
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Default
Yes
Yes
Yes
Disabled
N/A
N/A
N/A
N/A
N/A
N/A
Enabled
5 second(s
)
N/A
Enabled
Low
Enabled
N/A
N/A
N/A
Disabled
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Enabled
5 second(s
)
N/A
Enabled
Low
Enabled
N/A
N/A
N/A
Disabled
N/A
N/A
Default
Yes
Yes
Yes
Disabled
N/A
N/A
N/A
N/A
N/A
N/A
Enabled
Enabled
Low
Enabled
N/A
N/A
N/A
N/A
N/A
N/A
Default
Yes
Yes
Yes
Disabled
5 second(s
)
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Enabled
5 second(s
)
N/A
Enabled
Low
Enabled
N/A
N/A
N/A
Disabled
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
KDC User Manual O PERATING YOUR KDC reading d
Encrypt MSR
Data
AES Key
Length
Card Type
Enabled/Disable d
128bit/192bit/2
56bit
Track
Separator
ISO/OTHER
1/AAMVA
None/Space/Co mma/Semicolon
/CR/LF/CR&LF/T ab
Attach Start/End Sentinel
Partial Data Start Position
Partial Data Length
Partial Data
Action
Erase/Select
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Disabled
128bit
ISO
None
Enabled
1
0
Select
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Didabled Disabled
128bit
ISO
None
Enabled
1
0
Select
Table 3 - KDC Menu
N/A
ISO
None
Enabled
1
0
Select
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
55
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
56
KDC User Manual O PERATING YOUR KDC
KDC Mode Menu
The KDC Mode Menu has two options – Normal mode and Application mode.
Normal
This is the default mode that provides basic barcode scanning. In Normal mode, barcode data can be manipulated directly through the KDC or through KTSync the synchronization process.
® during
Application
This mode allows you to run the user application created by the Application Generation
Tool, as described in Chapter 7 Application Generation.
View Data Menu
This menu option allows you to view and/or delete barcodes stored in the KDC. In the case of the KDC20/30, you can delete the last scanned barcode by pressing the DELETE button on the right side of the unit.
Press the Delete button to delete the last scanned barcode.
Figure 17 - Delete Function in KDC20/30
Set Barcodes Menu
This menu lists all the barcode symbologies supported by the KDC and allows you to select the barcode symbologies to be scanned. For maximum scan performance, you should select only the symbologies that you will be scanning. Please refer to 11. Appendix
– 11.1 Symbologies for a detailed listing of symbologies supported by the KDC.
Code Options Menu
The KDC supports various Code Options, including Transmission of Start and Stop
Characters, Symbology Conversion, Verification of Optional Check Character, and
Transmission of Check Digit. Please refer to 11. Appendix A – 11.2 Code Options for a detailed explanation of each option.
Scan Options Menu
Scan Angle
(Opticon model only)
This option allows you to configure the laser beam angle to the barcode. There are two options for scan angle: Wide and Narrow. Wide is 54
Wide. o and Narrow is 27 o . The default is
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
57
KDC User Manual O PERATING YOUR KDC
Filter
(Opticon model only)
This menu allows you to change the Filter mode from Normal to High for poor quality barcodes. The default is Normal.
Timeout
In this menu, you can set the interval between scans. The timeout options are from 5 seconds up to 10 seconds. The default is 2 seconds.
Minimum Barcode Length
This option allows you to set a barcode length from 2 characters to 36 characters
(KDC20/100/200/250/350L/410/415) or 2 characters to 48 characters
(KDC30/300/350C/420/450). It is strongly recommended that you maximize the minimum barcode length setting to prevent possible errors.
The default minimum barcode length of KDC20/100/200/250/350L/410/415 is 4 characters.
The default minimum barcode length of KDC30/300/350C/420/450 is as follows:
Minimum (Default) Maximum (Default)
Codabar 2(4) 60(60)
Code 11 1(4) 80(80)
Code 32
Code 39
Code 93
Code 128
0(0)
0(0)
0(0)
48(48)
80(80)
80(80)
EAN-8
EAN-13
GS1 Composite
1D Symbology
Matrix 2of5 1(4) 80(80)
Plessey 4(4) 48(48)
PosiCode 2(4) 80(48)
GS1 Omni
GS1 Limited
GS1 Expanded
S2of5 Ind
S2of5 IATA
TCL39
4(4)
1(4)
1(4)
74(74)
48(48)
48(48)
Telepen 1(1) 60(60)
Trioptic
UPCA
UPCE0
UPCE1
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
58
KDC User Manual O PERATING YOUR KDC
2D Symbology
AztecCode 1(1) 3750(3750)
AztecRunes
CodablockF 1(1) 2048(2048)
Code16K 0(1) 160(160)
Code49 1(1) 81(81)
DataMatrix 1(1) 1500(1500)
MaxiCode 1(1) 150(150)
MicroPDF 1(1) 366(366)
Postal Codes
OCR
HanXin Code
Postnet
PlanetCode
UK Post
Canada Post
Kix Post
Australia Post
Japan Post
China Post
Korea Post
OCR Off
OCR A
OCR B
OCR USC
OCR MICR
OCR SEMI
2(4)
2(4)
Table 4 - KDC350C Minimum Barcode Length
80(80)
80(48)
Image Capture
(KDC30/300/350C/420/425/450)
This option allows you to capture an image in JPEG format in C:\myData folder. You should enable the image capture option first, and then press the Scan button to start the aiming. A green aiming light will illuminate and an image will be taken upon release of the
Scan button. KDC350C will disable the image capture option if the user presses the scan button for 10 seconds.
Security Level
(KDC20/100/200/250/350L/410/415)
This menu allows you to ensure an accurate barcode reading by setting the number of times the KDC will read a barcode. Security Level is set from 1 up to 4. The higher security level means readings are more reliable; however, some performance degradation is likely. For poor quality barcodes, we recommend increasing the security level. The default is 2.
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
59
KDC User Manual O PERATING YOUR KDC
Auto Trigger
Once enabled, Auto Trigger allows users to scan a barcode automatically. You can adjust
Reread delay from Continuous to Extra Long. Auto Trigger mode always enables the duplicate check option.
Note
USB cable insertion requirement is removed from FW2.85/86.O and FW 3.02.
You can exit the auto trigger mode by pressing the scan button for 3 seconds.
Reread Delay
You can adjust the Reread delay from Continuous to Extra Long. Auto Trigger mode always enables the duplicate check option.
Partial Display
This option allows you to display partial data. You can define the start position and number of characters to be displayed.
Data Process Menu
Wedge/Store
The KDC provides five modes of data transmission in keyboard wedging mode.
Wedge Only: Barcode data is NOT stored in memory but transmitted to the host.
Wedge & Store Only: Barcode data is stored in memory and transmitted to the host.
Store Only: Barcode data is stored in memory but NOT transmitted to the host.
Save if Sent: If data transmission is successful, barcode data is stored in memory.
Save if Not Sent: If data transmission is NOT successful, barcode data is stored in memory.
Data Format
The KDC provides two data formats, Barcode Only and Packet Data.
Barcode Only: The KDC transmits scanned barcodes only. You may incorporate appropriate data transmission error detection and correction mechanisms in this mode. KDC supports a selection of various termination characters for Barcode
Only format. You can select <NONE>, <CR>, <LF>, <CR+LF> or <TAB> as the termination character.
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
60
KDC User Manual O PERATING YOUR KDC
Packet Data: KDC transmits packet data with checksum to minimize transmission errors. KTSync ® sets Data Format to Packet Data format upon execution.
Note
You may change Data Format to Barcode Only if you would prefer to use the
Barcode Only mode. However, the KDC would stay in Packet Data mode if
KTSync is aborted abnormally. If this is the case, you may have to change the
KDC back to Barcode Only mode manually.
Barcode Index: KDC20i/30i/200i/250i/300i/350i/400i add 4 bytes barcode index to maintain last synchronized barcode information.
-
This optional index would be added if data format is “Packet Data”.
-
4 bytes index would be added before “@” when responding to “p” command.
-
4 bytes index plus “@” character would be added after checksum byte if the user scans a barcode and wedges to the host.
Data Editor
KDC provides various data editing options.
Prefix - Allows you to add a prefix to scanned data, that can then be stored in the
KDC or wedged to the host. The Prefix format must be defined in the Data
Format menu of KTSync. The maximum length for a Prefix is 11 characters.
Note
Note
This Prefix option is different from the Prefix option in KTSync, which attaches the prefix to data during synchronization.
The user can also define the prefix by scanning characters defined in
Appendix C. between the following special barcodes.
KDC 20/100/200/250/300/350L/410/415
Prefix Enter Start
Prefix/Suffix Enter Finish
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
61
KDC User Manual O PERATING YOUR KDC
KDC30/350C/420/425
Prefix Enter Start
Prefix/Suffix Enter Finish
Note
Users can also delete or display current prefixes by scanning the following special barcodes.
KDC20/100/200/250/300/350L/410/415
Delete Prefix
Display Prefix
KDC30/350C/420/425
Delete Prefix
Display Prefix
Suffix - Allows you to add a suffix to scanned data, which can then be stored in the KDC or wedged to the host. The suffix must be defined in the Data Format menu of KTSync. The maximum length for a suffix is 11 characters.
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
62
KDC User Manual O PERATING YOUR KDC
Note
Note
This Suffix option is different from the Suffix option in KTSync, which appends the suffix to data during synchronization.
The user can also define a suffix by scanning characters defined in Appendix
C.27 ~ C.28 (KDC350L) and Appendix D.27 ~ D.28 (KDC350C) by scanning the following special barcodes:
KDC20/100/200/250/300/350L/410/415
Suffix Enter Start
Prefix/Suffix Enter Finish
KDC30/350C/420/425
Suffix Enter Start
Prefix/Suffix Enter Finish
Note
The user can also delete or display a current suffix by scanning the following special barcodes.
KDC20/100/200/250/300/350L/410/415
Delete Suffix
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
63
KDC User Manual O PERATING YOUR KDC
Display Suffix
KDC30/350C/420/425
Delete Suffix
Display Suffix
AIM ID - Allows you to add AIM ID to scanned data, which can then be stored in the KDC or wedged to the host. AIM ID must be defined in the Data Format menu of KTSync. AIM ID is added to the end of either a Prefix or Suffix.
Partial Data: Allows you to store and/or transfer partial data. The user defines the start position and number of characters to be stored and/or transferred.
Select the
x
characters from
y
position
Set Partial Data Start Position to
Action to Select
y
, Partial Data Length to
x,
Partial Data
Partial Data Length
0
selects all characters from
y
position.
Erase the
x
characters from
y
position
Set Partial Data Start Position to
Action to Erase
y
, Partial Data Length to
x,
Partial Data
Partial Data Length
0
erases all characters from
y
position.
Handshake
KDC provides Handshake mode when Data Format is set to Packet Data.
Handshake Mode will increase the reliability of barcode data transmission.
The default mode for Handshake is Disabled.
Data transmission speed is slower when Handshake Mode is Enabled.
Terminator
The KDC supports various termination characters when the Data Format mode is set to
Barcode Only. This option allows you to select <NONE>, <CR>, <LF>, <CR+LF>, or
<TAB> as the termination character. The default terminator is <CR+LF>. The
Up/Down/Left/Right arrow terminator is also available for HID mode.
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
64
KDC User Manual O PERATING YOUR KDC
Chk Duplicate
This option prevents you from collecting duplicate data.
Enter Key
(KDC350 Only)
This option determines the behavior of the ‘#’ key on the KDC350 keypad.
If this option is enabled, the ‘#’ key acts as a keyboard enter key.
The ‘#’ key finishes the current data input, and stores/sends input data according to the menu settings of Wedge/Store.
The cursor moves to next line after the current data input is complete, regardless of whether there is an data input or not.
The screen is scrolled up one line if the ‘#’ key is pressed on the last line of
KDC screen.
If ‘Shift’ is enabled, remember that the ‘#’ key will input the ‘#’ character.
When the KDC sends input data to the host, it attaches a terminator selected in the menu “Data Process Terminator”. This option can be enabled by scanning a special barcode, as shown in 13.8(KDC350L) and 14.8(KDC350C)
If this option is disabled, the ‘#’ key acts as a scan button (when ‘Shift’ is not enabled).
BT Config Menu – KDC20/30/200/250/300/400
The KDC supports
Bluetooth
Ver2.1+EDR. Before utilizing the advantages of Bluetooth functionality with the KDC, the user should become familiar with Bluetooth connectivity and its impact on the host environment.
To configure your KDC for Bluetooth functionality, you can use the KDC Menus. To access the menus, simultaneously press the UP and DOWN buttons on the side of the KDC. Use the DOWN button to scroll to Bluetooth, then press SCAN button.
Below is a listing of the Bluetooth options and their settings. The default settings for these options have been set to increase the usability of Bluetooth technology without compromising the KDC battery usage.
IMPORTANT: We strongly recommend NOT changing these settings until the user has fully tested the Bluetooth connection between the KDC and the host device.
For more detailed information regarding Bluetooth functionality with the KDC, please refer to Chapter 4. BLUETOOTH.
ConnectDevice
You can choose the Bluetooth device type in this option.
HID normal - KDC20(i)/30(i)/200Ii)/250(i)/300(i)/350(i)/400(i)/450(i)
HID iOS - KDC20(i)/30(i)/200Ii)/250(i)/300(i)/350(i)/400(i)/450(i)
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
65
KDC User Manual O PERATING YOUR KDC
SPP2.0 - KDC20(i)/30(i)/200Ii)/250(i)/300(i)/350(i)/400(i)/450(i)
SPP - KDC20(i)/30(i)/200Ii)/250(i)/300(i)/350(i)/400(i)/450(i)
iPhone (KDC20i/30i/200i/250i/300i/350i/400i/450i)
Auto Connect
Enabled or Disabled
Auto Reconnect
Enabled or Disabled (iPhone, HID iOS, HID normal mode)
Auto Power On
Enabled or Disabled
PWR On Time
Disabled, 1 to 10 seconds
Auto Power Off
Enabled or Disabled (KDC250/350 should use option in system menu)
Beep Warning
Enabled or Disabled
PWR Off Time
1 to 30 Minutes
PowerOff Msg
Enabled or Disabled
MAC Address
When users select this option, KDC displays 12 characters
Bluetooth
MAC Address.
FW Version
This option displays
Bluetooth
Firmware Version
Wakeup Nulls
Enabled or Disabled
Autolock Time
0, 1, 2, 3, 4, 5, 10, 15 minutes
BT Toggle
Enable or Disable HID soft keyboard or iPhone mode connection On/Off toggle.
BT Disconnect Button
Enable or Disable Bluetooth disconnection by pressing down button for 3 seconds.
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
66
KDC User Manual O PERATING YOUR KDC
HID AutoLock
Disabled, 1, 2, 3, 4, 5, 10, 15 minutes
HID Keyboard
Users can select a keyboard language in HID mode. KDC supports five languages:
English, German, French, Spanish, and Italian.
HID Initial Delay
In this menu, users can define the initial delay between 1 second to 10 seconds before data transmission in HID mode
HID Inter-character Delay
This option allows users to define the inter-character delay between 10msec to
100msec in HID mode
HID Control Character
This option helps users to map control characters to either ALT+Numlock or
^+Character.
BT Service – KDC20/30/200/250/300/350/400
Power
Users can choose to turn Bluetooth Power on or off. Select between Enable and Disable.
Pairing Mode
This option allows user to enter pairing mode by simply selecting this menu.
The KDC enters into pairing mode so that the host for it.
Bluetooth
device can search
The KDC can exit pairing mode if the user presses the SCAN button or if it fails to pair with the
Bluetooth
host device within 90 seconds.
Discovering
When users choose this menu, KDC searches for nearby
Bluetooth
devices.
Connecting To
This option allows user to Inquire to registered
Bluetooth
devices.
HID Sync
KDC transmits all stored data to the host over HID profile if HID Sync option is enabled.
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
67
KDC User Manual O PERATING YOUR KDC
GPS Config - 350G
Barcode and GPS data format
The KDC350 adds the GPS coordinate after the barcode data, if GPS data is available. The
GPS data starts with “<G|P/S]” and ends with “:”. For example, the KDC250 would record barcode “1234567890” , GPS coordinate “4354.45275,N;07925.81993,W” and Altitude data “208.7,M”as “1234567890<G|P/S]4354.45275,N;07925.81993,W ,208.7,M:” in the barcode data field.
GPS Menu
GPS Power: Turning GPS Power on or off
Users can enable or disable the GPS Power.
The GPS module consumes extensive battery power. To conserve battery power, it is strongly recommended to turn off the GPS option when the
KDC350 is not being used for an extended period of time.
It is also recommended to use the GPS Auto Power Off option in the System menu. This option automatically turns off the GPS power if a barcode is not scanned for a period of time.
Power Mode: The user can choose the type power consumption for the GPS function.
Users can extend the battery life of the KDC350 in Power Save mode.
Users should use normal mode if accurate GPS data is required.
The KDC350 will last about 15 hours in normal non-bypass data mode and 18 hours in power save non-bypass data mode.
The KDC350 will last about 7 hours in normal bypass data mode and 8 hours in power save bypass data mode.
Bypass Data: Enabled or Disabled
This option should be disabled if users wish to record the GPS data with a scanned barcode data.
The KDC350 will bypass GPS data to the host if the bypass option is enabled.
The KDC350 becomes a Bluetooth GPS receiver if this bypass data option is selected.
Acquire Test: Time test to see how long it takes to acquire GPS signal.
Reset GPS: Reset GPS parameters
GPS Hot Key
The KDC350 provides the following hot keys for convenient GPS operations:
GPS Power Enable
If Auto Power Off is enabled and GPS power is disabled, users can turn on the GPS power by pressing the SCAN button.
Users should hold the SCAN button for more than 3 seconds to turn on the
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
68
KDC User Manual O PERATING YOUR KDC
GPS power.
GPS Bypass mode Enable/Disable
If GPS power is enabled, users can toggle GPS Bypass mode by pressing the
SCAN button.
Users should hold the SCAN button for more than 3 seconds to toggle GPS bypass mode.
GPS Acquire test cancellation
Users can cancel the GPS acquire test by pressing the SCAN button during the test.
GPS Data append cancellation
Users can cancel GPS data append by pressing SCAN button if GPS data is not available immediately.
Users should hold the SCAN button for more than 3 seconds to cancel GPS data append.
USB DISK - 100M/200M/250M/300M/350
USB Mode
KDC100M/200M/250M/300M/350 can be used as USB Disk with 4MB space.
USB Serial
When this option is enabled, KDC enters into USB Serial mode.
USB Disk
This option allows user to change to USB Disk mode and barcode data that KDC scanned is stored into a file in flash disk when this option is selected.
Disk Format
This option is available in USB Disk mode and allows users to format KDC USB Disk.
Data Format
This option is available in USB Disk mode.
Note
Data
Data Time
Data Type
Data Time Type
Changing the “USB Mode” option will erase all data in KDC memory.
Make sure to back up your data before changing this option.
KTSync cannot recognize the KDC if the KDC is in “USB DISK” mode.
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
69
KDC User Manual O PERATING YOUR KDC
It is required for the user to run "Verify Disk" on Disk Utility before using it.
NFC Config – KDC350N/KDC400N
NFC Power
Turning NFC Power on or off
Options: Enable/Disable
Data Format
Options: Data only/Packet data
UID Only
Enable or Disable UID Only menu
The KDC only sends UID data to the host device when the KDC is in UID Only mode. If Data format is ‘Data Only’ or HID mode, the KDC changes the UID hex values to ascii string and sends this data to the host device. If Data format is
‘Packet Data’, the KDC only sends UID hexa values with NFC/RFID packet format.
Note
KDC350N/400N supports the following card types.
1) Mifare Desfile read.
2) Mifare 1K read.
3) Mifare Ultralight / Ultralight C
4) ISO 15693
System Menu
Memory Size (3.0 version only)
The user can select how much memory to divide between normal data memory and application database memory.
The KDC will erase all stored data upon changing the partition size.
The user should enter the following key sequence to change the partition.
UP button + UP button + DOWN button + DOWN button + SCAN button
Memory Status
In this option, users can checks the number of stored barcodes and memory usage.
Reset Memory
In this option, users can reset KDC memory by erasing all stored barcodes, applications, and BT registry.
Auto Erase
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
70
KDC User Manual O PERATING YOUR KDC
If enabled, this feature erases stored barcodes on the KDC once the ‘Buffer Full’ condition is reached.
Sleep Timeout
This option allows users to set the amount of time the KDC waits before going to
(when not being used).
sleep
Auto Power Off (KDC250/350)
Bluetooth: Enabled/Disabled
GPS: Enabled/Disabled
Power Off Time:0(Never), 5, 10, 20, 30, 60, 120 minutes
Date/Time
In this option, users can set the date and time of the KDC, which can also be set using
KTSync ® .
Battery
This option shows the current status of battery power level.
Version
This option shows the KDC firmware version and serial number.
Button Lock
This option allows users to lock or unlock the KDC scan and scroll buttons.
Beep Alert
Beep Sound: Enables or disables KDC beep sound.
Power On Beep: Enables or disables beep sound when KDC power is on.
Beep On Connect: Enables or disables beep sound when KDC is connected to the host.
Beep On Scan: Enables or disables beep sound when KDC is scanning.
Beep Volume
This option allows user to adjust the beep volume from High to Low.
MFi Mode (KDC20i, 30i, 200i, 250i, 300i, 350i, 400i)
This option allows user to enable or disable MFi mode. MFi mode supports SPP and iPhone Bluetooth profiles. Non-MFi mode supports SPP, SPP2.0, HID iOS and HID normal.
Vibrator
Enables or disables KDC vibrator.
Auto Exit
This option enables KDC to automatically exit KDC Menus.
Port Status
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
71
KDC User Manual O PERATING YOUR KDC
This option allows users to enable or disable KDC port messages.
Display Format
There are various selection of display format; Time & Battery, Type & Time, Type &
Battery, Memory Status and Barcode only.
Menu Barcode
This option allows users to enable or disable Honeywell special barcodes (KDC300/350C only).
Scrolling
This option allows users to enable or disable display scrolling for a barcode with more than 40 characters.
Brightness
This option allows users to adjust brightness of display.
Note
Factory Default
By selecting this option, users can reset KDC options to factory default settings.
Pair and connect KDC20i/30i/200i/250i/300i/350i/400i and iOS4.0+ in
HID iOS mode
Users have to disable the MFi option in System > MFi menu and change the
Bluetooth profile to HID-iOS to use HID Bluetooth profiles
.
Users have to RESET the iPhone/iPad/iPod touch in order to change HID to iPhone mode, and vice versa, after removing a previous KDC connection.
KDC with Bluetooth Spec2.1+EDR does not prompt Pin code entry menu.
KDC with Bluetooth Spec. 2.1+EDR stack does not require 4 or 6 digits PIN digits entry
Follow the below steps in order to pair and connect KDC models for MFi and iOS4.0 in HID mode.
1.
Go to the KDC System > MFi menu.
2.
Change MFi option to Disabled.
3.
Change ConnectDevice to HID-iOS
4.
Remove previous KDC connection and RESET the device
5.
Change KDC to Pairing mode.
6.
The iPhone/iPad/iPod touch will find a new device as
Keyboard
.
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
KDC User Manual O PERATING YOUR KDC
7.
Click
Keyboard
device.
iOS Soft Keyboard toggling using BT Toggle option
Users need to select the option to use this feature in BT Config > BT Toggle. Press the
DOWN button to toggle a soft keyboard.
72
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
73
KDC User Manual O PERATING YOUR KDC
3.4 LED Status
KDC100/200/250/300/350
LED Color
Green
Orange
Red
Status
Successful Reading
USB is connected and battery is fully charged.
Low battery
USB is connected and battery is charging.
No reading
Empty battery
KDC20/30/400
LED Color
Green
Orange
Red
Status
T
Successful Reading
USB is connected and battery is fully charged. iPhone mode in pairing mode.
Low battery
USB is connected and battery is charging
HID mode is in pairing mode.
No reading
SPP mode is in pairing mode.
Table 5 - Explanation of LEDs
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
74
KDC User Manual O PERATING YOUR KDC
3.5 Empty Battery
KDC100/200/250/300/350
The KDC will display the message
Empty Battery Connect USB
when the battery is empty.
Please charge the KDC IMMEDIATELY to prevent any interruptions while it is collecting data.
KDC20/30/400
Under 30% - Orange LED flickers at 1-second-intervals for 5 seconds every minute.
Under 20% - Orange LED flickers at 1-second-intervals for 10 seconds every minute.
Under 10% - Red LED flickers in 1- second-interval for 10 seconds every minute, and the user will hear a beeping sound.
3.6 Buffer Full
The KDC will display the message
Buffer Full
when the size of collected data reaches
160KB (85 version) / 60KB (86 version) or the number of collected barcodes reaches 10,240.
To prevent the loss of data, you should synchronize the data then reset the memory when this message is displayed.
The 4MB version KDC reaches the Buffer Full condition in the following situations:
0.5MB Partition - Collected data size reaches 0.5MB or collected number is 25,600
1MB Partition - Collected data size reaches 1MB or collected number is 51,200
2MB Partition - Collected data size reaches 2MB or collected number is 102,400
3MB Partition - Collected data size reaches 3MB or collected number is 153,600
4MB Partition - Collected data size reaches 4MB or collected number is 204,800
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
KDC User Manual O PERATING YOUR KDC
3.7 Reset Feature (100/200/250/300/350) or Poweron/off (KDC20/30)
The Reset feature allows you to restart the KDC100/200/250/300/350/400 if necessary, without losing any stored barcode data or option settings. To reset the KDC, follow the below steps.
1. Press the DOWN and SCAN buttons simultaneously for 5 seconds.
2.
When the LEDs illuminate orange, release the buttons.
3. The KDC initial screen, KoamTac Data Collector KDC, displays when reset is complete.
Note
The KDC stores collected data into flash memory and will not lose data nor the
KDC settings during the reset process.
However, if you are using the KDC20/30, you can turn the power on and off by pressing the DOWN and SCAN button simultaneously for 5 seconds. When the LED light is green, you can release the buttons and the power will be on. When you turn off the KDC20/30, you will hear a beep sound after pressing the DOWN and SCAN buttons simultaneously.
75
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
76
KDC User Manual O PERATING YOUR KDC
3
3.8 Replace Battery
Each KDC comes with a rechargeable, Lithium-polymer (KDC20/30/100/200) or Lithiumion (KDC300/350/400) battery. The battery can be recharged from any USB port or KDC charging cradle, and can be recharged about 300 times before it needs to be replaced. KOAMTAC recommends replacing the battery annually, as a declining battery will cause noticeable performance degradation in the KDC. Replacement batteries can be purchased from a KDC reseller. Batteries should be disposed of properly as according to the WEEE regulation. The steps for replacing a battery are as follows.
1
.
Disassemble the KDC back cover by unscrewing the middle screw.
2.
Remove the old battery and replace with a new battery.
3.
Reassemble the back cover.
1
Unscrew the screw indicated by the arrow.
2
Remove the battery cover by pulling it down.
Remove the battery.
Pull out the 2 pin connecter gently.
Figure 18 - Replacing a Battery
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
77
KDC User Manual B LUETOOTH
4. Bluetooth –
KDC20/30/200/250/300/350/400
The KDC20/30/200/250/300/350/400 supports HID (Human Interface Device) normal, HID iOS, SPP (Serial Port Profile) and SPP2.0 profiles. The KDC20i/30i/200i/250i/300i/350i/400i supports iPhone (Made for iPhone) profiles too. They are compatible with the following
Bluetooth stacks:
BlueSoleil
Broadcom (Widcomm)
Microsoft Windows XP, Vista, 7, and Mobile5.0+
Toshiba
The KDC200/250/300/350’s
Bluetooth
the PC KTSync and special barcodes.
options can be configured by using the KDC menu and special barcodes. The KDC20/30/400’s Bluetooth options can be configured by using
4.1 Bluetooth Config
ConnectDevice
The KDC supports both Serial Port Profile (SPP) and Human Interface Device Profile (HID).
The user can choose amongst SPP2.0, SPP(2.1), HID normal, or HID iOS profiles to communicate with the host device. An additional iPhone (Made for iPhone) option is available for KDC20i/30i/200i/250i/300i/350i/400i models.
If the BT Toggle option in BT Config is enabled, the user can connect and disconnect the
Bluetooth connection with the host device by pressing the UP and DOWN buttons. It normally takes 3 seconds to connect and 1 second to disconnect. This is a very useful feature for iPhone and iPad applications.
The user can also enable and disable the iPhone and iPad soft keyboard instantly by using this BT Toggle option.
The UP button shows the Bluetooth connection status and the DOWN button shows the time when the KDC is connected via SPP profile.
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
78
KDC User Manual B LUETOOTH
Note
The user should first unpair the KDC from the Bluetooth host to change the
Connect Device setting on the scanner to a different Bluetooth profile.
Auto Connect
This feature allows the KDC to automatically connect to the host device when the KDC is powered on.
IMPORTANT: Until the host device and KDC have been fully tested, it is strongly recommended that this feature be set to ‘Disable’, because a host device that does not support this feature could cause problems, such as power loss or upload delays.
Note
The KDC automatically tries to connect to the host 10 times within the duration of two minutes when
Bluetooth
power is ON,
Bluetooth
is disconnected, Auto Connect is enabled, and system Sleep Timeout is set to
5 seconds.
Auto Reconnect
This feature allows the KDC to automatically connect to the host device when the KDC is disconnected from a host.
IMPORTANT: This feature is available when KDC “Connect Device” options are “iPhone”,
“HID iOS”, or “HID Normal”.
Note
The KDC tries to connect automatically to the host 10 times within the duration of two minutes if Bluetooth is disconnected.
Auto Power On
The Auto Power On option allows the KDC to automatically power on Bluetooth when the
SCAN button is pressed. The default setting is Disabled.
Note
Users should press the scan button for the duration defined in the BT Config
Power-on time option. The host program may have to open the COM port again in order to be reconnected with the KDC.
PWR ON Time
The PWR On Time option works in conjunction with the Auto Power On option. The default value is Disabled. If the KDC Bluetooth power is off, you can turn on the Bluetooth power by pressing the SCAN button for the PWR On Time option value.
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
79
KDC User Manual B LUETOOTH
Auto Power Off
The Auto Power Off option works in conjunction with the PWR Off Time option. This option allows the KDC to power off Bluetooth automatically when the KDC is NOT
CONNECTED to the host for the time duration specified in the PWR Off Time option.
The default for this option is Disabled. It is strongly recommended to keep it enabled to maximize the operation time of the KDC. If Auto Power Off is Enabled, Bluetooth can be manually powered off before the specified time in the PWR Off Time option.
Beep Warning
The KDC beeps to acknowledge the status of the Bluetooth connection as follows:
1. One high short beep when Bluetooth is connected.
2. One low short when Bluetooth is disconnected.
3. Five short beeps if:
“Beep Warning is ENABLED”
“Auto Power Off is DISABLED”
“KDC20/30/200/250/300/400 is DISCONNECTED from HOST”
“Bluetooth power is ON”
PWR OFF Time
The PWR Off Time option works in conjunction with the Auto Power Off option. If Auto
Power Off is Enabled, the KDC powers off Bluetooth when the duration of time specified in the PWR Off Time option is met and the KDC is NOT CONNECTED to the host. The time setting for this option is from one (1) minute to 30 minutes. The default is five (5) minutes.
PowerOFF Msg
The KDC sends a Bluetooth power off message “BTOFF” to the host if the PowerOFF message option is enabled.
MAC Address
The user can verify the KDC Bluetooth MAC Address.
FW Version
The user can verify the KDC Bluetooth firmware version in BT FW menu.
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
80
KDC User Manual B LUETOOTH
Wakeup Nulls
The KDC sends three leading Null bytes to wake up the feature can be disabled if the bytes to wake up.
Bluetooth
connected device. This
Bluetooth
connected device does not require additional
Autolock Time
The iPhone/iPad/iPod touch loses incoming Bluetooth data while in sleep mode. To prevent data loss, you can set the KDC Autolock time to the same Autolock time of your iPhone/iPad/iPod touch, to use the automatic wakeup feature in HID mode.
If the Autolock time is set to more than one minute and the barcode scan interval is larger than the auto-lock time, there will be a one second delay of barcode transmission. The autolock time would be set as 0, 1, 2, 3, 4, 5, 10, 15 minutes. 0 means the iPhone/iPad/iPod touch never enters sleep mode.
HID Keyboard
The user can select an international keyboard – English, German, French, Spanish, or
Italian.
HID Initial and Inter-Character Delay
Certain applications cannot process HID input fast enough and may lose some characters during transmission. Users should increase initial and inter-character delay to prevent data loss during HID transmission.
HID Initial Delay: Defines the initial delay between 1 sec to 10 sec before data transmission in HID mode.
HID Inter-character Delay: Defines the inter-character delay between 10msec to 100msec in HID mode.
Control character transmission in HID mode
Control characters between ASCII values 0x00 and 0x1F can be replaced by the
ALT+Numpad or ^+Character.
Disabled Transmit the original control character.
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
81
KDC User Manual B LUETOOTH
Alt+Numpad Transmit Alt+ ASCII value from Numpad.
^+Character Control characters would be substituted as shown in the following table.
Replacement to | Control characters would be substituted as “|”.
Control
Char
0x01
0x02
0x03
0x04
0x05
Transmit
Chars
^A
^B
^C
^D
^E
Control
Char
0x0B
0x0C
0x0E
0x0F
0x10
Transmit
Chars
^K
^L
^N
^O
^P
0x06
0x07
^F
^G
0x11
0x12
^Q
^R
0x19
0x1A
0x09 ^I 0x13 ^S 0x1C
Function key transmission in HID mode
Control
Char
0x14
0x15
0x16
0x17
0x18
Transmit
Chars
^T
^U
^V
^W
^X
^Y
^Z
^\
Control
Char
0x1D
0x1E
0x1F
The user can send F1 to F12 function keys by scanning special barcodes in HID mode.
Disconnect/Reconnect/BT(HID) Toggle
The user can disconnect or reconnect the Bluetooth connection, and toggle the soft keyboard using side buttons.
Bluetooth
Profile
SPP
UP Key
Does nothing
HID iOS Reconnect iPhone
SPP 2.0
Reconnect
Does nothing
HID normal Reconnect
DOWN Key
(DisconnectBTN disabled)
Does nothing
Soft Keyboard Toggle if pressing less than 3sec
Does nothing
Does nothing
Does nothing
DOWN Key
(DisconnectBTN enabled)
Releases BT connection
Soft Keyboard Toggle if pressing less than 3sec,
Releases BT connection
Releases BT connection
Releases BT connection
Releases BT connection
Transmit
Chars
^]
^^
^_
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
82
KDC User Manual B LUETOOTH
4.2 Bluetooth Service
Power
The POWER option allows you to Enable or Disable the Bluetooth functionality of the KDC.
To use Bluetooth, this option must be set to Enable.
However, like all devices enabled for Bluetooth, the KDC will constantly search to connect with a Bluetooth host when set to Enable. Constant searching for Bluetooth devices increases power consumption.
Unless you are using Bluetooth with your KDC, this option should be set to Disable.
IMPORTANT: To prevent unnecessary power problems, it is strongly recommended that the POWER option be set to Disable if the KDC is idle for an extended period of time.
Pairing
Before you are able to use Bluetooth, the KDC must be paired with the host device. This pairing process needs to be completed only once with each host device. After pairing, the host device will always recognize the KDC as a Bluetooth device, unless the Bluetooth configuration is modified. If it is modified, you may need to pair the devices again.
IMPORTANT: The host device must be configured for Bluetooth before it can be paired to the KDC.
Note KDC with Bluetooth Spec2.1+EDR does not prompt Pin code entry menu.
To pair the KDC with the host, follow these instructions:
1. Select Pairing from the Bluetooth menu. The message “Pairing started…” will be displayed.
2. When prompted by the host device, enter the Security PIN “0000”.
3. The “Pairing success” message will display when the Bluetooth connection is successfully established. The connection must be established before the pairing timeout of 60 seconds.
If “Pairing failed...” message displays, the Bluetooth connection with the host device failed. If the message “Connected” displays, a Bluetooth connection is established.
It is possible for the message “Pairing failed...” to display on the KDC while the host device displays the “Connected” message. If this occurs, a
Bluetooth connection has been established.
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
KDC User Manual B LUETOOTH
Discovering
KDC20/30/200/250/300/350/400 starts to search for neighboring
Bluetooth
devices if the
Discovering menu is executed. It will take about 30 seconds to finish searching and to list available neighboring
Bluetooth
devices. Another option is to enter the corresponding
Bluetooth MAC address in the KTSync Bluetooth menu, instead of waiting for the KDC to search for neighborhood
Bluetooth
devices.
Connect To
This option lets you easily connect the KDC to previously registered in KTSync under the File Menu or discovered/connected from the
KDC
Bluetooth
Note
Service menu.
Bluetooth
devices that have been either
There could be an interoperability issue depending on the corresponding device Bluetooth stack. The master Bluetooth device may request that you to follow the master Bluetooth device’s security procedures, if the KDC tries to connect to the master Bluetooth device.
HID Sync
The user can synchronize stored barcode data over HID using the HID Sync option. The
KDC will start to transmit all stored barcode data upon execution of the HID Sync option.
This option is available when KDC MFi Mode option is disabled.
83
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
84
KDC User Manual S YNCHRONIZATION
5. Synchronization
When barcode data is collected, it must be uploaded to your application. KTSync ® , which is bundled with the KDC, is a software that allows barcode data to be uploaded to any PC, PDA, or smartphone running Android 2.1+, Apple iOS3.1.3+, Blackberry, Mac and
Windows XP/Vista/7/Mobile 5.0+. It has three major functions. (Windows XP/Vista/7 version supports all of the following features. Tablet, PDA and Smartphone versions support only limited features of PC KTSync.)
Synchronization - Provides data upload functionality to your applications.
Keyboard Emulator - Allows scanned data to be uploaded directly into your application as if the data were being entered manually with a keyboard.
Application Generation - Allows users to create custom applications or download predefined applications such as Master-Slave, Pick/Bin, DB Lookup and Inventory.
Additional functions include:
Prefix and Suffix add-ons to eliminate manual data entry.
Symbology and Scan Option selections.
Barcode Wedging options.
5.1 KTSync Menu
KTSync ® was installed on your PC during the initial installation process. Before data can be uploaded to any host device, KTSync ® must be launched on the host and configured to recognize the KDC. The following screen displays when KTSync ® is launched:
KDC100/200/250/300/350
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
KDC User Manual S YNCHRONIZATION
85
File Menu
KDC20/30/400
Figure 19 - KTSync ® Synchronizer Menu
Connect: This option displays the Serial port (COM#) assigned to KDC. You can also use this option to manually assign the Serial port. The Serial port assigned to
KDC can be found under Windows Device Manager. The port assignment is used by KTSync ® for synchronizing data from the KDC to the host.
Synchronize: This option manually tells the KDC to synchronize data with the host.
While data is being synchronized, KTSync menu options are unavailable.
Note Please do not use your computer during data synchronization.
Bluetooth: This option is not available on KDC100. Users can register a MAC address to be directly connected by KDC20/30/200/250/300/350/400.
Configuration: This option allows users to set different KDCs with same settings by exporting and importing settings from one KDC to the other.
Exit: This option ends the KTSync program. You must re-run KTSync before you can synchronize data on the KDC.
Figure 20 - File Menu
Settings Menu
Synchronization: Select Synchronize options.
Barcode & KDC: Select Barcode and KDC options.
Others: Select Auto Connection and/or Synchronization Confirmation options.
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
KDC User Manual S YNCHRONIZATION
86
Figure 21 – Setting Menu
Application Menu
Generation: Create user application or download predefined application.
DB Lookup: Allows users to download DB into KDC and display barcode description field.
Master/Slave: The user defines a master barcode for comparison with one or more slave barcodes.
Pick/BIN: The user defines Pick ID and the barcode symbology for comparison with a defined Bin.
Inventory: Users can count inventories. Inventory description will be displayed if inventory DB is downloaded into the KDC.
Figure 22 - Application Menu
About Menu - KTSync ® - Version Information
Figure 23 - About Menu
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
87
KDC User Manual S YNCHRONIZATION
5.2 File Menu
Connect to KDC
The KDC automatically connects to a COM port when connected to the PC’s USB port. If needed, the user can manually assign the KDC COM port by using the KTSync
Connection submenu under the File menu.
®
Figure 24 - COM Port Selection for KDC
The COM port assignment is found in the Windows Device Manager.
KTSync ® will not connect to the KDC if it is in the KDC Menus. You must EXIT from the KDC Menus.
If KTSync ® fails to connect automatically to the KDC, please follow these steps:
Note
1. Exit KTSync ® .
2. Check to make sure that you have connected the KDC to a USB port on your PC.
3. Make sure that the user is using the cable provided with the KDC.
4. Check to make sure that the KDC is not in KDC Mode Menu.
5. Restart KTSync ® .
You can manually assign the COM port using KTSync under the File menu.
® Connect option
Synchronize
Located under the File Menu, this option allows the user to manually synchronize data on
KDC with the host. This option is similar to clicking on the Synchronize button in the
KoamTac Data Synchronizer box.
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
88
KDC User Manual S YNCHRONIZATION
Bluetooth
This menu option allows the user to register up to ten Bluetooth devices, including their
MAC address, PIN #, and optional prefixes or suffixes. This option enables direct
Bluetooth connection between KDC and other Bluetooth devices, such as a
Bluetooth
printer. The user should choose a
Bluetooth
device to be connected in “Connect to” menu in KDC
Bluetooth
Service menu.
Configuration
Figure 25 - Bluetooth Device Registry
This menu is useful for the users who need to configure different KDCs with same settings.
In this menu, you can export settings from a KDC to your computer and import it to other
KDCs.
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
89
KDC User Manual S YNCHRONIZATION
When you select Configuration in File menu, you will need to choose either Export or
Import. First, select Export. You name the settings file, press Open, and it is exported to your computer. Second, connect a different KDC to your computer and import the settings file to the KDC by selecting Import in the Configuration menu. Once configuration has been finished, KDC will restart.
Export
Import
Figure 26 – Configuration
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
90
KDC User Manual S YNCHRONIZATION
5.3 Synchronization Settings
KTSync ® provides several synchronization options for synchronizing data from your KDC to host devices such as your PC, PDA, or smartphone running Windows XP, Vista, Windows 7, or Mobile 5.0+.
Figure 27 - KTSync ® Synchronization Settings
Destination of Data
When barcode data is uploaded to the host device, you must assign a destination for the data. Destination of Data options include:
File - This option means data will be saved in the assigned filename. You can select a different target directory by clicking the New icon. The default directory is
C:\MyData\sn_timestamp.txt. If this directory is not created, you will be prompted to create it before data can be uploaded to a file.
Active Window - This option means scanned barcode data is sent directly to the active program running on your device as if the data is being entered directly from a keyboard.
Microsoft Excel - This option means barcode data is being imported directly into
Microsoft’s Excel. Various parameters can be set when uploading data to Excel.
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
91
KDC User Manual S YNCHRONIZATION
Select from Current Running Application – This option allows you to select a currently running application for data synchronization.
• Data synchronization begins immediately if Automatically After
Connection is selected. If not selected, data synchronization is started manually by the user.
Note
• Users SHOULD NOT operate the PC during the synchronization process.
It can interrupt the process causing unreliable results.
Synchronization Methods
Fast Synchronization in Burst Mode
The KDC can synchronize data to a host device in Burst mode or Sequential mode. Burst mode provides the fastest synchronization process but could result in error in a poor
Bluetooth
environment. Fast synchronization in Burst mode is only recommended with
USB connection.
Synchronize Normal Data
If Synchronize Normal Data option is selected, the KDC will synchronize only Normal Data in KDC memory. If the user wants all data in KDC memory synchronized, the user should select Synchronize Normal Data and Synchronize Application Data.
Synchronize Application Data
If Synchronize Application Data option is selected, the KDC will synchronize only
Application Data in KDC memory. If the user want all data in KDC memory synchronized, the user should select Synchronize Normal Data and Synchronize Application Data.
Clear KDC Memory after Synchronization
If this option is selected, the stored barcode data is cleared from the KDC memory after synchronization. The KDC20/30/100/200/250 can store a total of 10,240 barcodes or 60KB
(86 version)/160KB (85 version) of barcode data.
It is important to clear the KDC memory periodically to prevent a Buffer Full message. Buffer Full prevents the KDC from storing additional data. Stored barcode data can also be deleted using the Reset Memory feature on the KDC.
Automatically Synchronize after Connection
This option lets the user automatically synchronize collected data immediately to the computer when the KDC is connected to the host.
IMPORTANT: Before selecting this option, remember to configure all options properly.
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
92
KDC User Manual S YNCHRONIZATION
Data synchronization can be done manually by clicking the synchronize icon if this option is not selected.
Beep while Synchronization
The user can enable or disable the beep tone during the synchronization process. If this option is selected, a beep is sounded every time barcode data is synchronized. The KDC beeps 5 times when the synchronization process is complete.
Append data to File
If the user has specified a file name and Append data to File option is enabled, KTSync will append data to the existing file instead of creating a new file.
Current KDC Wedge Method
The KDC can be configured in one of five Wedge/Store modes:
Wedge Only - Scanned data is transmitted to the host. The KDC does not store scanned data.
Wedge & Store - Scanned data is stored in the KDC and transmitted to the host.
Store Only - Scanned data is stored in the KDC but NOT transmitted to the host.
Save if Sent - Scanned data is stored in the KDC ONLY if transmission to the host is successful.
Save if Not Sent - Scanned data is stored in the KDC ONLY if transmission to the host is unsuccessful.
Enable Wedge (Handheld Scanner Mode)
This option will be checked if Wedge Only or Wedge & Store option is selected.
Keep Scan Data in KDC
This option will be checked if Store Only or Wedge & Store option is selected.
Synchronization Options
Synchronize KDC Time with PC Time when Connected
This option enables the user to synchronize the KDC date and time with the host date and time. Synchronization of date and time occurs after the data is uploaded to the host device.
Delays
The user can set transmission delays between barcodes and characters during the synchronization process. It is important to set proper delays to prevent errors during the
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
93
KDC User Manual S YNCHRONIZATION transmission of collected barcodes. Some Windows applications, such as Excel, require longer delay times.
Attachments
Timestamp, Barcode Type, and Serial Number can be attached to the scanned barcode by selecting these options. The Serial Number of the KDC can be attached to the Start or End of Record.
Prefix and Suffix
Enter the characters the user wants to attach to the front (Prefix) or back (Suffix) of the barcode in the Prefix and Suffix fields.
The character set is any combination of ASCII characters including alphanumeric, line feed (“\n”), and carriage return (“\r”).
Order and Delimiter
Select Order of Data – Type, Data, and Timestamp
Select the Delimiter between Data – Tab, Space, Comma, and Semicolon
Select the Delimiter between Records – None, LF, CR, Tab, and <LF & CR>
Application Options
Synchronize Non-Compliant Data
The KDC will synchronize both compliant and non-compliant data (filtered data) if
Synchronize Non-Compliant Data option is Enabled.
Consolidate Steps in One Record
KTSync will consolidate the data collected in Step 1 with the data collected in Step 2 and/or Step 3. When Consolidate Steps in One Record is Enabled, data will be consolidated into one record instead of individual data records for each step. If this option is Enabled, non-complete records, i.e. three steps were defined but data was only collected for two steps, will be discarded.
Attach Quantity
If this option is Enabled, quantity will be attached to the left or right of the data.
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
KDC User Manual S YNCHRONIZATION
5.4 Barcode & KDC Settings
KTSync ® allows the user to configure the KDC Scan Options and Barcode Settings. The configuration options for the KDC using KTSync ® are similar to the Set Barcodes, Code
Options, Data Editing and Scan Options on the KDC Menu. Please refer to 11. Appendix
A – Barcode & Scan Options for proper barcode settings for the application.
Note
The user must configure barcode and scan options properly for optimal KDC performance.
94
Figure 28 - Barcode & KDC Settings, Symbologies, Data Editing and Scan Options
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
95
KDC User Manual S YNCHRONIZATION
Select Symbologies and Symbology Options
The process for scanning and reading barcodes is delicate and complicated. Although your KDC is equipped with a high performance scan engine, if configured incorrectly it may not perform at its peak performance level. To ensure its high performance, the KDC comes configured to optimize its scan engine technology. Unless you clearly understand the impact of your changes to the KDC settings, please do not change factory default settings. Please refer to Appendix A for details. Pressing the Default icon will reset all symbology related options to factory default settings.
Data Editing Option
Prefix
- Allows the user to add a prefix to scanned data that can then be stored in KDC or wedged to the host. The Prefix format must be defined in the data format menu of
KTSync. The maximum length for a Prefix is 11 characters.
Note
This Prefix option is different from the Prefix option in KTSync that appends the prefix to data during synchronization.
Suffix
- Allows the user to add a suffix to scanned data, which can then be stored in KDC or wedged to the host. The Suffix must be defined in the data format menu of KTSync.
The maximum length for a Suffix is 11 characters.
Note
This Suffix option is different from the Suffix option in KTSync that appends the suffix to data during synchronization.
AIM ID
- Allows the user to add AIM ID to scanned data, which can then be stored in KDC or wedged to the host. AIM ID must be defined in data format menu of KTSync. AIM ID is either added to the end of Prefix or Suffix.
Partial Data
: Allows the user to display and store partial data. The user defines the start position and number of characters to be displayed and stored.
Select the
x
characters from
y
position
Set Partial Data Start Position to
y
, Partial Data Length to
x,
Partial Data
Action to Select.
Partial Data Length
0
selects all characters from
y
position.
Erase the
x
characters from
y
position
Set Partial Data Start Position to
y
, Partial Data Length to
x,
Partial Data
Action to Erase.
Partial Data Length
0
erases all characters from
y
position.
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
96
KDC User Manual S YNCHRONIZATION
5.5 Other Settings
Other options under the Settings menu allow the user to select four additional settings:
Ask Confirmation before Trying Auto Connection prevents unintentional launch of KTSync.
Ask Confirmation before Starting Auto Synchronization prevents unintentional synchronization of data.
Minimize KTSync on Start will minimize KTSync and send it to the tray upon execution.
Keep Checking
Bluetooth
Connection allows reconnection of KDC once
Bluetooth
signal is detected. This feature is useful when moving to or from
Bluetooth
host device frequently. KTSync will automatically reconnect
Bluetooth
connection when the user enter an effective
Bluetooth
network range.
(Not Available on KDC100)
To select any of these settings, click on the box to the left of the setting. A check mark () will display next to the setting to indicate that it is selected.
Figure 29 - KTSync ® Confirmation Settings
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
97
KDC User Manual S YNCHRONIZATION
5.6 KDC Menu in KTSync (KDC20/30/400)
After connecting KDC 20/30/400 to PC with a USB cable, run KTSync on your PC and you will see KDC Menu on the right side of KTSync window. Click KDC Menu, and you can configure your KDC20/30/400 in KDC Menu window, as shown below.
Figure 30 - KDC Menu in KTSync (KDC20/30/400)
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
98
KDC User Manual S YNCHRONIZATION
5.7 Mobile pKTSync
pKTSync provides limited functionality for Pocket PC 2003 and Mobile 5.0+ users.
1. Synchronization - Provides data upload functionality to your applications.
2.
Keyboard Emulator - Allows scanned data to be uploaded directly into your application as if the data were being entered manually on a keyboard.
For detailed explanations of these functions, please refer to earlier sections of this chapter.
WARNING: The user must assign the correct COM port to KDC before using pKTSync.
Please refer to the mobile device manual for details on Bluetooth pairing and COM port assignment methods.
Figure 31 - Mobile pKTSync
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
99
KDC User Manual S YNCHRONIZATION
5.8 Android aKTSync
The aKTSync provides limited functionality of PC KTSync to Android users.
Note
aKTSync only supports Android devices with 2.1+ OS version and that are compatible with BluetoothChat application.
KDC with Bluetooth Spec2.1+EDR doesn’t prompt Pin code entry menu.
KDC and Android Pairing
1.
Pairing
Select SPP Bluetooth profile from the KDC ConnectDevice submenu in BT
Config menu.
Search KDCxxx from Android and pair the two devices.
If SPP2.0 is selected, KDCxxx PIN code is “0000”.
2. Connection
Click Connect icon in aKTSync.
Android will list paired target KDC.
Bluetooth
devices and the user should select the
3. Synchronization: Provides data upload functionality to the applications.
4. Settings: The user can change various Synchronization options in the settings menu.
5. Wedging: The user can wedge barcode data to any Android application. Press the home key and launch the target application.
Launch KTSync
1. Download and install aKTSync from the Android Play Store.
2.
Change KDC Bluetooth ConnectDevice option to
SPP.
3. Execute Android
Bluetooth
device scan option and KDC
Bluetooth
pairing option.
A. Execute KDC
Bluetooth
Pairing option.
B. Launch Settings on the Android device.
C. Select Wireless and Networks.
D. Click on Bluetooth Settings.
E. Click on Scan devices.
F. The Android device will display the KDC model and 6 digits of the serial number.
4. Press the KDC list entry, enter “0000” PIN code, and press OK.
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
100
KDC User Manual S YNCHRONIZATION
5.
When paired, the Android device will display “
Paired but not connected”
.
6. Launch aKTSync program.
A. Press menu key and select the Connect option on the top left.
B. From the list of paired devices, choose the KDC to use.
C. On the top menu bar of aKTSync, you will see a message “
connecting”
, and then
“
connected”
.
D. On the KDC display, you will see “Pairing Succeeded!!!” and then “Bluetooth
Connected”.
E. Select Settings option on the bottom left to change aKTSync setting.
Figure 32 - Android aKTSync
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
KDC User Manual S YNCHRONIZATION
Keyboard Wedge
1.
Launch Settings on the Android device.
2.
Select Language and Keyboard (or Input method).
3.
Select KTSync Keyboard.
4.
Launch the application and touch the input box to focus.
5.
The barcode will be wedged to the input box upon scanning a barcode.
101
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
102
KDC User Manual S YNCHRONIZATION
5.9 iPad/iPhone/iPod touch KTSync
The KTSync for iPad/iPhone/iPod touch provides limited functionality of PC KTSync for iPad, iPhone and iPod touch users.
1. The KDC supports SPP and iPhone Bluetooth profiles.
2.
The iPhone/iPad/iPod touch should use iPhone Bluetooth profiles. iPhone is the default profile of KDCi models.
3.
Download the KTSync program from the App Store.
4. Enable the iPhone/iPad/iPod touch Bluetooth power from the Setting > General >
Bluetooth menu.
Note
• Users have to disable MFi option in System > MFi menu to use HID
Bluetooth profiles.
• Users have to RESET the iPhone/iPad/iPod touch to change “HID to iPhone mode” or “vice versa” after removing previous KDC connection.
KDC with Bluetooth Spec2.1+EDR does not prompt Pin code entry menu.
KDC20i/30i/200i/250i/300i/350i/400i connection using iPhone mode
1. Download and install iKTSync from the Apple App Store. http://itunes.apple.com/us/app/ktsync/id372916602?mt=8
2. Press the two KDC side buttons simultaneously to enter menu mode.
3. Scroll down to Bluetooth menu using KDC Down button.
4. Press the front middle scan button.
5. Scroll down to Discovering and press the front middle scan button. a. “Discovering Started …” message will be displayed on KDC screen. b. Discovering will take about 30 seconds.
6. Select discovered iPhone/iPod touch device name and press the front middle scan button. a. [Pin Code] User Default/Enter PinCode will be displayed. b. Press the front middle scan button to select the Use Default option. c. The message “Connecting to iPhone/iPod touch device name” will be displayed. d. iPhone/iPad/iPod touch will ask for the PIN number. f. Please enter “0000” and hit “connect” icon. g.“iPhone Connected” message will be displayed.
7. Launch KTSync and configure Settings.
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
103
KDC User Manual S YNCHRONIZATION
iKTSync Settings
iKTSync provides following Settings menu.
Synchronization - The user can configure Synchronization options, such as destination of data, data formation and delimiters.
Other settings - Users can configure KDC350 GPS module, disconnection options and soft trigger button.
Figure 33 - iPad/iPhone/iPod touch KTSync
How to connect and reconnect iPhone mode using UP keys
1. The user needs to select the option to use this feature in the BT Config > BT Toggle.
2.
Press the UP button to connect or reconnect to the iPhone/iPad/iPod touch.
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
104
KDC User Manual S YNCHRONIZATION
5.10 Blackberry bKTSync
The bKTSync provides limited functionality of PC KTSync for Blackberry users.
Note KDC with Bluetooth Spec2.1+EDR does not prompt Pin code entry menu.
1.
Download and install bKTSync from the Blackberry App World. http://appworld.blackberry.com/webstore/search/ktsync?lang=en
2.
Go to Blackberry Options > Applications menu and enable Input Simulation option.
3.
Change KDC Bluetooth profile in ConnectDevice option to SPP.
4 . Execute Blackberry
Bluetooth
manager and KDC
Bluetooth
pairing option:
A. Execute KDC
Bluetooth
Pairing option.
B. Launch the Blackberry
Bluetooth
manager and select “Search”. The KDC model and
6 digits of the serial number will be displayed.
C. Highlight the KDC and press the Enter or Select Key.
D. Enter “0000” PIN code and press the Enter or Select Key.
E.
The Blackberry will display
“Pairing with KDC”
and then
”complete.”
F. Close the Blackberry Bluetooth manager.
5.
Go to Downloads folder and execute KTSync.
6 . The user can configure KDC options in KDC settings and Symbologies Settings menu.
7.
Go to KTSync Synchronization Settings and select Destination. To send collected barcode data as an email attachment, choose Email Attachment as destination and enter in the email address, subject, and body message that the user want to send. The user can enter multiple email addresses using the semicolon (;) separator.
8.
To scan barcodes into any application (like email, notes, worksheet or web browser), press the menu key and select Running in the background option. bKTSync will maintain the connection and place the scanned barcode data wherever the cursor is flashing.
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
KDC User Manual S YNCHRONIZATION
105
Figure 34 - Blackberry bKTSync
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
106
KDC User Manual S YNCHRONIZATION
5.11 KTSync for Mac OS X
The KTSync Mac OS X version provides limited functionality of PC Windows KTSync for
Mac OS X users.
Note
KTSync for Mac OS X version supports both Bluetooth SPP profile and USB connection. The user should pair KDC with Mac before using the KTSync program via Bluetooth connection.
Mac OS X version KTSync is built as a X86 binary application and works with the Intel-based Mac. It is verified on Mac PC running Mac OS X 10.6.5 and later versions.
KTSync Mac OS X version supports the following features:
Keyboard wedge function to a file, internal viewer, active window, and user application.
Synchronization to a file, internal viewer, active window, and user application.
Automatic connection and disconnection on USB port.
The user will see the following initial KTSync screen upon launching the program. KTSync will connect automatically if KDC is plugged in a USB port or if KDC is paired.
Connect Button
The user can connect the Mac with the KDC that is paired or plugged into the USB port by clicking the Connect button. The following screen will be displayed when this button is pressed, and KTSync will start to connect to the selected KDC.
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
107
KDC User Manual S YNCHRONIZATION
Disconnect Button
KTSync changes Connect button to Disconnect button once the KDC is connected. The user can disconnect the KDC manually by selecting connected KDC on the following screen.
Synchronize Button
The user can start the synchronization process by pressing the
Synchronize button. The user can select the destination of barcode data in the settings menu. There are 4 selectable destinations: File, Internal viewer, Active window, and User application.
Clear Button
The user may press this button to clear the KTSync internal viewer.
Settings Button
The user can configure synchronization options on the following screen by pressing the Settings button.
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
108
KDC User Manual S YNCHRONIZATION
Destination of data
The KTSync program wedges or downloads barcode data to one of the following four destinations:
File: The KTSync makes a file name based on 3.11 if file name is specified as an
“sn_timestamp.txt”. The default directory is /Users/Shared/KTSyncData directory. The user can define another directory or another filename by clicking the “New” button. The maximum file path length is 128 characters.
Internal viewer: The KTSync displays barcode data in KTSync internal text viewer.
Active window: The KTSync sends barcode data to current active window if Active window option is selected.
User application: The user can define the target application by pressing the “New” button. The maximum application name path length is 128 characters.
Synchronization Options
Synchronize KDC clock
KTSync will set the KDC’s date and time with Mac PC date and time when the
KDC is connected to Mac, if this option is enabled.
Burst synchronization
KTSync will synchronize barcode data from KDC in burst mode. Otherwise,
KTSync would synchronize barcode data one by one. This option is enabled by default and cannot be disabled.
Synchronization on connection
KTSync will automatically synchronize barcode data from the KDC when the KDC is connected, if this option is enabled.
Clear KDC memory after synchronization
KTSync clears barcode data stored in the KDC’s memory once synchronization has finished, if this option is enabled.
Append data to file
KTSync appends synchronized data to existing file specified on destination. If file does not exist then KTSync creates a new file.
Data Edition
Attach serial number
The KTSync will add a KDC serial number to barcode data. This option is enabled by default and cannot be disabled.
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
109
KDC User Manual S YNCHRONIZATION
Attach time stamp
The KTSync would add timestamp to barcode data. This option is enabled by default and cannot be disabled.
Attached barcode type
The KTSync would add barcode type to barcode data. This option is enabled by default and cannot be disabled.
Serial number
When Attach serial number is enabled, this option determines when to attach serial number. “Start of record” means to attach at the front of record and “End of record” means to attach to the end of record.
Data order
This option specifies the order of data (Barcode Type, Barcode Data and
Timestamp) in the record.
Data delimiter
This option is used to select a character to be added between barcode data, serial number and timestamp and/or barcode type. User can select one of the following: None, Tab, Space, Comma and Semicolon as the data delimiter. The
Comma is selected as the data delimiter by default.
Record delimiter
This option is used to select a character to be added at the end of the barcode record. The user can select one of None, CR, LF, TAB, and CR&LF as the record delimiter. The CR&LF is selected as the record delimiter by default.
Other Options
Non-English keyboard
This option is used when the barcode data has non-English characters and a non-English keyboard.
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
KDC User Manual A PPLICATION G ENERATION
6. Application Generation
Note
KDC FW2.85.200.x does not support the Application Generation feature.
Users should upgrade FW2.85.200.x to FW2.86.200.x to use Application
Generation feature.
When you select the Application menu from the KTSync, youthe user can choose from the following five Applications: Generation, DB Lookup, Master/Slave, Pick/BIN, and Inventory.
Users can also download saved programs using the Import & Download option.
Figure 35 - Application Menu
When the Application tool is selected, the KDC will beep once to acknowledge a connection between the KDC and the Application tool. The following KTSync warning window will pop up if the downloaded application in KDC does not match with KTSync application tool.
110
Figure 36 - Application Warning Window
Note
KDC will wedge barcode data to the host in application mode if “wedge and store always” option in data process menu is selected and KDC firmware version is higher than 2.86.xxx.G.
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
111
KDC User Manual A PPLICATION G ENERATION
6.1 Application Generation
KDC Application Generation tool is a robust feature that allows you to create custom applications for collecting and managing barcode data. To create a custom application, select the Generation submenu from the Application menu in KTSync ® .
Figure 37 - Application Generation Menu
Generate Application
Generate step 1 -
To generate a custom application, click on the Generate Step 1 box.
This enables the user to define the user prompts and data collection settings for Step 1 of the custom application. Below is a description of each field. These prompts are the same when selecting Generate step 2 and Generate step 3.
Note The custom application can include only Step 1.
First line
Enter up to 13 characters; these will display on the first line of the KDC.
Second line
Enter up to 13 characters; these will display on the second line of the KDC.
Starting quantity
Enter a predefined start quantity for each scanned barcode. The start quantity
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
KDC User Manual A PPLICATION G ENERATION
can be defined from 1 to 128. Use the up or down side key to choose the desired quantity.
Waiting to scan
Enter the number of seconds the KDC pauses before the user prompts display.
During this timeout period, the user can modify the quantity. If this field is set to zero, the quantity field cannot be adjusted. This field can be defined from
“-1” to “30” seconds. “-1” second enables infinite waiting of user quantity input.
Enable data filter
Check this box to enable the data filtering option. Data filtering allows the user to predefine different aspects of the barcode data the user are collecting.
Data Filter Settings
When the user select Enable data filtering, the user must click on the Settings button to select the Data filter setting. The options for the Data filter settings are the same for Step1,
Step 2, and Step 3.
112
Figure 38 - Data Filter Settings
Barcode Type
This field allows the user to select the type of barcodes the KDC will collect.
When the user clicks on the box, Select Symbols is enabled. A listing of the
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
113
KDC User Manual A PPLICATION G ENERATION
symbologies supported by the KDC will display. To select a barcode symbology, click on the box associated with the symbology.
Minimum Data Length
This field allows the user to define the minimum length of the scanned barcode.
The length can be between 2 and 36(KDC350L), 2 and 48(KDC350C) characters. If the user scans a barcode that has a length of less than the defined length, the barcode data is not collected.
Note
The default KDC minimum barcode length defined in scan option is 4.
Therefore, users should change KDC minimum barcode length to 2 or
3 to define minimum data length to 2 or 3.
Maximum Data Length
This field allows the user to define the maximum length of a scanned barcode. The defined length can be between 2 and 256 characters. If the user scans a barcode that has a length is greater than the defined length, the barcode data is not collected.
Barcode Collation
This option enables the user to define a data string that the KDC will use to compare scanned barcodes.
Starting Position – This is the start position of the scanned barcode data to be compared with the defined data string.
Data String – This is the defined value to be compared with scanned barcode data. This value can be up to 32 characters.
Collect Partial Data
This option allows the user to define partial barcode data to be collected when a barcode is scanned. Only the partial data will be stored in the KDC.
Start position – This is the starting position that the KDC will use when collecting scanned barcode data.
Data Length – This is the length of partial data to be stored by the KDC.
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
114
KDC User Manual A PPLICATION G ENERATION
Check for Duplicated Data
This option allows the user to prevent the collection of duplicate data.
Previous Scanned Data – This option allows the user to compare the scanned barcode with the previously scanned barcode and treat it as noncompliant data if the user scanned the same barcode twice.
All Stored Data – This option allows the user to compare the scanned barcode with stored barcode data and treat it as non-compliant data if the same barcode already scanned and stored.
Do not Save Non-Compliant Data
This field tells the KDC how to manage non-compliant data based on the defined data filtering fields. If this field is enabled, non-compliant data is NOT stored in the KDC. If this option is not enabled, non-compliant data is stored.
Generate step 2
To include another step in the data collection process, click the box, Generate step 2.
This step has the same options as Step 1. In this step, the user have the option of repeating step 2 by clicking the box, Repeat Step.
Note This field is disabled when the application has three steps.
Generate step 3
To include a third step, click the box, Generate step 3. This step has the same options as step 1 and 2. In this step, the user has the option to repeat steps 2 or 3.
Application Download and Execution
Before running your application, it must be downloaded to KDC.
1 . Click the “Download” icon from Application Generation Window.
2.
Change KDC from Normal mode to Application mode.
A. Press two side buttons simultaneously to enter menu mode.
B. Select KDC mode and enter scan button.
C. Change to Application mode.
D. Save and exit from menu mode.
3.
KDC will run in normal mode if you do not change to Application mode after downloading the application.
4.
If you want to delete the downloaded application in your KDC, select App. Data in
Reset Memory after you go to System Config in KDC Menu.
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
115
KDC User Manual A PPLICATION G ENERATION
6.2 Predefined Applications
KTSync provides four Predefined Applications: Master/Slave, Pick/Bin, DB Lookup and
Inventory.
Master/Slave
Master/Slave predefined application allows you to define a
master
barcode for comparison with one or more
slave
barcodes. The predefined application can be run once or continuously. Within either setting, you can define a substring for comparison of master and slave barcodes.
Master/Slave Onetime
Define one
master
barcode and compare it with one
slave
barcode.
Master/Slave Continuous
Define one
master
barcode and compare it with multiple
slave
barcodes.
Collation Options
Works in either Onetime or Continuous Mode to compare a substring within the master and slave barcodes.
Master start position - Select the numeric position of start substring character in
Pick barcode, 1 to 255.
Slave start position - Select the numeric position of start substring character in
Pick barcode, 1 to 255.
Comparing Barcode Length - Number of characters to be compared, 0 to 255. 0 means all characters.
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
116
KDC User Manual A PPLICATION G ENERATION
Pick/Bin
The Pick/Bin predefined application is a special version of the Master/Slave predefined application. The Pick/Bin application allows you to define the Pick ID and the barcode symbology for comparison with a defined Bin.
Number of ID and Symbology
Define Pick ID characters from 1 to 32 and the barcode symbology.
Figure 39 - Master/Slave Application Settings
Up
Key
Onetime
Scan Master
Barcode
Mismatched
Up or Down
Key ?
Scan Check
Barcode
Down
Key
KDC Mode
Select MS Mode:
(Onetime,
Continuous)
Collation :
Define substring to be compared.
Default is entire barcode
Continuous
Scan Master
Barcode
Yes
Matched
Matched
Up Key?
Scan Check
Barcode
No
Down
Key
Mismatched
Up or Down
Key?
Up
Key
Figure 40 - Master/Slave Application Flow Chart
Pick Start Position and Symbology
Select numeric position of start substring character in Pick barcode from 1 to
255 and the barcode symbology.
Bin Start Position and Symbology
Select the numeric position of start substring character in Bin barcode from 1 to 255 and the barcode symbology.
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
KDC User Manual A PPLICATION G ENERATION
Comparing Barcode Length
Select the number of characters to be compared from 0 to 255. 0 means all characters.
Figure 41 - Pick/BIN Application Menu
117
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
KDC User Manual A PPLICATION G ENERATION
118
Figure 42 - Pick/BIN Application Flow Chart
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
119
KDC User Manual A PPLICATION G ENERATION
DB Lookup Application
The DB Lookup application allows you to download a database to the KDC that can then be utilized for advanced AUTO-ID applications, such as displaying additional data after scanning a barcode. For example, using our DB Lookup application, you can download a product database including information such as description, price, and stock quantity.
With the advanced data functionality built-in to the KDC, you can easily display product price, description, and stock level after the product’s barcode is scanned.
Functionality of DB Lookup Application
The database size cannot exceed 800 records.
The maximum record size is 128 bytes.
Each record can have up to 4 fields, including the barcode, which is the primary key.
The maximum field size is 39 characters.
Quantities can be entered by pressing the UP or DOWN scroll buttons after DB fields are displayed.
Quantity can be 1 to 128.
The user can create a database using Microsoft Excel.
1. Excel file must be saved as .txt.
2. Records should be separated by CR/LF.
3. Fields should be separated by TAB.
4. Database should end with CR/LF.
5. Last 4 bytes of database should be CR/LF/CR/LF.
DB Lookup Fields and Settings
Download DB to KDC - Downloads user created database to KDC.
Starting Quantity - Enter predefined start quantity for each scanned barcode.
The start quantity can be defined from 1 to 128 and can be adjusted using UP or
DOWN buttons.
Barcode Field - Select the position of barcode field in database from 1 to 4.
Stored Barcode Start Position - Select the numeric position of start substring character of barcode in database from 1 to 39.
Scanned Barcode Start Position - Select the numeric position of start substring character of scanned barcode from 1 to 39.
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
120
KDC User Manual A PPLICATION G ENERATION
Comparing Barcode Length - Number of characters to be compared from 0 to
255 where 0 is all characters.
Display on KDC - Define database fields to be displayed on KDC. KDC can display one to three fields. KDC will display one field in two or three lines, if same field is specified in line entering option.
Figure 43 - DB Lookup Application Menu
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
121
KDC User Manual A PPLICATION G ENERATION
Inventory Application
The Inventory application allows the user to count inventories by scanning inventory barcodes. This application will increase inventory item count if the same item is scanned.
Users can also download an inventory database to the KDC. If inventory DB is downloaded, KDC will display inventory description after scanning a barcode.
Functionality of Inventory Application
The inventory cannot exceed 800 items.
The maximum record size is 128 bytes.
Each record can have up to 4 fields, including the barcode, which is the primary key.
The maximum field size is 39 characters.
Quantities 1 to 32786 can be entered by pressing the UP or DOWN buttons after inventory is scanned.
Starting Quantity can be 1 to 128.
Min/Max. Data Length is between 2 to 256 (KDC100/200/250/350L) or 4 to 256
(KDC300/350C).
Barcode Collation Start Position is between 1 to 256.
The length of Collation Data String is between 1 to 30.
Collect Partial Data Start Position is between 1 to 256.
Collect Partial Data Length is between 1 to 256.
Users can create an inventory database using Microsoft Excel.
Excel file must be saved as .txt.
Click User Inventory DB option to display inventory description.
Click Do not add non-existing item into DB if one do not wish to add new items into inventory DB.
The number of Barcode Data Field is between 1 to 4.
The position of Display Filed is between 1 to 4.
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
KDC User Manual A PPLICATION G ENERATION
Figure 44 - Inventory Application
122
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
123
KDC User Manual T ROUBLESHOOTING
7. Troubleshooting
PROBLEM
KDC not working
KDC not charging
Failed reading
KDC reads wrong barcode
Can’t communicate with PC, PDA, or smartphone
LED blinks yellow
Buffer Full
Message
Empty Battery
Message
Abnormal KTSync
Operation on
DELL PC
CAUSE
Dead battery
Hardware failure
Bad battery
Poor USB port
Damaged barcode
Out of scan range
Incorrect angle
Symbology
not supported
Scan options
Dirty scan window
Damaged scan window
Dirty scan window
Damaged scan window
Poor quality barcode
USB cable is not connected properly
Software is not working properly
COM configuration
Low battery power
Full Memory
Empty battery
Quickset Utility
WSED Utility
SOLUTION
Charge battery by connecting KDC to your PC using the included cable
Contact distributor for technical support
Replace battery – Contact Local
Distributor
USB port doesn’t supply proper current to KDC
- Charge KDC using a different
USB port on your PC
Scan a different barcode
Move the scanner closer to barcode
Move scanner farther from the barcode
Change the angle of scanner to barcode
Contact KOAMTAC - www.KOAMTAC.com for possibility of custom symbology support
Check scan option settings
Clean scan window
Replace scan window
Clean scan window
Replace scan window
Select only necessary barcodes
Increase minimum barcode length
Increase security level
Check cable connection between KDC and host device
Reload the software
Check COM port configurations
Charge the battery by connecting KDC to
PC.
KDC will lose collected data if the battery is empty.
Clear the Memory using Synchronization program
Connect USB immediately.
Synchronize the collected data and charge KDC
Disable Quickset Utility before using
KTSync.
Dell Quickset utility interrupts normal
KTSync operation
Disable WSED Wireless enable/disable utility
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
KDC User Manual T ROUBLESHOOTING
delete the folder C:\Program
Files\WSED, which contains a file
WSED.exe, with the same icon as in the taskbar
Delete the registry entry
KEY_LOCAL_MACHINE
\SOFTWARE\Microsoft\Windows\Current
Version\Run\WSED
Table 6 - Troubleshooting Techniques
124
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
125
KDC User Manual W ARRANTY
8. Warranty
LIMITED WARRANTY AND DISCLAIMERS
BY OPENING THE PACKAGE OF THIS PRODUCT YOU AGREE TO BECOME BOUND BY THE
LIABILITY AND WARRANTY CONDITIONS AS DESCRIBED BELOW.
UNDER ALL CIRCUMSTANCES, THIS MANUAL SHOULD BE READ ATTENTIVELY, BEFORE
INSTALLING AND OR USING THE PRODUCT.
Serial Number
A serial number appears on the KDC label. This official registration number is strictly related to the device purchased. Make sure that the serial number appearing on your KDC is not removed.
Removing the serial number will affect the warranty conditions and liability disadvantageously, so please maintain the label with serial number on the KDC. Units with the serial number label removed should not be operated.
Warranty/Warranty Period/Liability
KOAMTAC, Inc. (“KOAMTAC”) manufactures its hardware products in accordance with industrystandard practices. Unless otherwise agreed in a contract, KDC is warranted for a period of one year after purchase, covering defects in material and workmanship except rechargeable battery.
KOAMTAC will repair or, at its opinion, replace products that prove to be defective in material or workmanship under proper use during the warranty period. KOAMTAC will not be liable in cases (i) in which the unit has been repaired or altered unless done or approved by KOAMTAC, (ii) in which the unit has not been maintained in accordance with any operating or handling instructions supplied by KOAMTAC, (iii) in which the unit has been subjected to unusual physical or electrical stress, misuse, abuse, power shortage, negligence or accident or (iv) in which the unit has been used other than in accordance with the product operating and handling instructions. Preventive maintenance is the responsibility of the customer and is not covered under this warranty. Under no circumstance will KOAMTAC be liable for any direct, indirect, consequential or incidental damages arising out of use or inability to use either the hardware or software, even if KOAMTAC has been informed about the possibility of such damages.
Warranty Coverage and Procedure
During the warranty period, KOAMTAC will repair or replace defective products returned to
KOAMTAC warehouse. International customers should contact the local KOAMTAC office or support center. If warranty service is required, KOAMTAC will issue a Return Material Authorization
Number. Products must be shipped in the original or comparable package, shipping and insurance charges prepaid. KOAMTAC will ship the repaired or replacement product freight and insurance prepaid. Customer accepts full responsibility for its software and data including the appropriate backup thereof. Repair or replacement of a product during warranty will not extend the original warranty term.
CAUTION: Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the user’s authority to operate the equipment.
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
126
KDC User Manual C ONTACT I NFORMATION
9. Contact Information
CORPORATE HEADQUARTERS
116 Village Blvd., Suite 305
Princeton, NJ 08540, USA
Phone: 609-256-4700, FAX: 609-228-4373
Email: [email protected]
For more information, visit our website - www.KOAMTAC.com
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
127
KDC User Manual B ARCODE & S CAN O PTIONS
10. Appendix A – Barcode & Scan
Options
The process for scanning and reading barcodes is delicate and complicated. Although the
KDC is equipped with a high performance scan engine, if configured incorrectly, it may not perform at its peak performance level. To ensure its high performance, the KDC comes configured to optimize its scan engine technology. Unless you clearly understand the impact of your changes to the KDC settings, please do not change factory default settings.
10.1 Symbologies
KOAMTAC’s KDC products support most major barcode symbologies including 1D, 2D,
Postal, and OCR-Fonts. Below is the list of the barcode symbologies supported by the
KDC with respect to each model’s particular area of support. To ensure superior scan performance, remember to select only the required symbologies.
KDC30/300/350C/420/425/450
1D
Barcodes
2D
Barcodes
Postal
Barcodes
KDC20/100/200/250/350L/
410/415
EAN13, EAN8, UPCA, UPCE,
Bookland EAN, EAN13 with Addon,
EAN8 with Add-on, UPCA with Addon, UPCE with Add-on, Interleave 2 of 5, ITF14, Code128, Codabar, GS1-
128, Code39, Code93, & Code35
N/A
N/A
Codabar, Code11, Code32, Code39,
Code128, EAN8, EAN13, GS1-128,
I2of5, MSI, Plessey, PosiCode, GS1
DATABAR OMNI, GS1 Limited, GS1
Expanded, S2of5IA, S2of5ID, TLC39,
Telepen, Trioptic, UPCA, & UPCE
AztecCode, AztecRunes,
CodablockF,Code 16K, Code49,
DataMatrix, MaxiCode, MicroPDF,
PDF417, & QRCode and
HanXin Code
AusPost, CanadaPost, ChinaPost,
JapanPost, KoreaPost, KixPost, Planet
Code, Postnet (US), & UKPost
OCR
Fonts
N/A
OCR-A, OCR-B, OCRUSCurrency,
OCRMICRE13B, & OCRSEMIFONT
Table 7 - Symbologies Supported by KDC
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
128
KDC User Manual B ARCODE & S CAN O PTIONS
Bookland EAN vs. EAN-13
Bookland EAN, which includes ISBN, ISSN, and ISMN, is supported by the KDC. This group of symbologies is essentially an EAN-13 barcode with fixed prefixes; 977 for ISSN, 978 for
ISBN, and 979 for ISMN. If EAN-13 and Bookland EAN are both enabled, Bookland EAN takes precedence. Bookland EAN does not have any options. The Bookland EAN barcode does not contain any groupings – that is, there are no hyphens or separators. Thus, the ISBN
957-630-239-0 is transmitted as 9576302390.
Add-on Symbologies
By default, the 2 or 5 digit add-on symbols with a UPCE, UPCA, EAN-8, and EAN-13 barcode are neither decoded nor transmitted. Transmission for these specific symbologies is enabled by setting the appropriate
withAddon
options. There are 4
withAddon
options, one for each symbology:
UPCEwithAddon
UPCAwithAddon
EAN8withAddon
EAN13withAddon
The decoding of add-on symbols are defined by the following table, which explains the process for EAN-13 symbols.
Mode Behavior Value of flags
Autodiscrimination
With add-on
If add-on symbol is present, then it is also decoded; otherwise, only the EAN-13 symbol is decoded.
Only EAN-13 barcodes with 2 or 5 addon symbols are decoded.
Without add-on The add-on symbol is ignored.
Table 8 - Add-on for EAN-13 Symbology true true false true true false
The add-on symbol is appended to the EAN-13 barcode. The process is similar for UPCE,
UPCA, and EAN-8 barcodes. Note that all the UPCE, UPCA, EAN-8, and EAN-13 formatting and conversion options are in effect. The following table should help explain the effect of various options for EAN-8 barcode 12345670 + 12.
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
129
KDC User Manual B ARCODE & S CAN O PTIONS
Barcode EAN8_as_EAN13 EAN8_Return
CheckDigit
EAN13_ReturnCh eckDigit
1234567012
123456712 False
00000123456712
000001234567012 True
Table 9 - Add-on for EAN-8 Symbology
The add-on symbol contains neither a check digit nor a terminating guard band. Every effort has been made to reduce the decoding error; however, it is likely to decode a partial scan of a 5-digit add-on symbol as a 2-digit add-on symbol. It is strongly recommended that the minimum security level be set at 2 while decoding add-on symbols. Since the decoder takes a conservative view on the add-on symbols, it is likely that the add-on symbol will be missed in the auto-discrimination mode. Autodiscrimination mode should then be avoided.
10.2 Code Options
(KDC20/30/100/200/250/410/415)
The KDC supports the following barcode options:
Transmission of start and stop characters
Reverse direction
Symbology conversion
Verification of optional check character
Transmission of check digit
Transmission of Start and Stop Characters
For Codabar symbols, the user can choose not to transmit the start and stop symbols, the
NOTIS Editing. By default, they are transmitted. Setting the field
CodaBar_NoStartStopChars to true disables the transmission.
Reverse Direction
This option may be selected if direction oriented symbologies are designated, such as
Code35.
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
130
KDC User Manual B ARCODE & S CAN O PTIONS
Symbology Conversion
By default the EAN-8, UPCE, and UPCA symbols are transmitted in their native format.
However, it is possible to show them in a different format. The user can choose to display UPCE symbols as either UPC-A or EAN-13 symbols, EAN-8 symbols as EAN-13 symbols, or UPC-A symbols as EAN-13 symbols. The following table shows the effect of setting various options.
Option
EAN8_as_EAN13
UPCA_as_EAN13
UPCE_as_EAN13
UPCE_as_UPCA
EAN-8
Converted to
EAN-13
No effect
UPC-A
No effect
UPC-E
No effect
Converted to
EAN-13
No effect
No effect
No effect Converted to
EAN-13
No effect No effect
Table 10 - Symbology Conversion
Converted to
UPC-A
All others
No effect
Verification of Optional “Check Digit”
Code39 and Interleave 2 of 5 have an optional check digit, which, by default, is not verified. Changing the option VerifyCheckDigit to true can enable their verification, or the user can enable the verification for individual symbologies. If the check digit verification fails, the barcode is not transmitted.
Option Selected
VerifyCheckDigit
Verify Code39 check digit
Yes
Verify I2of5 check digit
Yes
I2of5_VerifyCheckDigit No effect Yes
Table 11 - Verification of Optional "Check Digit"
Transmission of “Check Digit”
By default, the check digit – optional or mandatory – is not transmitted. Its transmission can be enabled for all symbologies by enabling ReturnCheckDigit option.
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
131
KDC User Manual B ARCODE & S CAN O PTIONS
Option Selected
ReturnCheckDigit
EAN13_ReturnCheckDigit Yes
Is the check digit returned?
Yes Yes Yes Yes Yes Yes
EAN8_ReturnCheckDigit
UPCA_ReturnCheckDigit
No effect
No effect
UPCE_ReturnCheckDigit No effect
Code39_ReturnCheckDigit No effect
I2of5_ReturnCheckDigit No effect
No effect
Yes
No effect
No effect
No effect
No effect
No effect
No effect
No effect
No effect
Yes No
No effect
No effect
No effect effect
No effect
No effect
No effect No effect
No effect No effect
No effect No effect effect No effect
Yes No effect
No effect Yes
Table 12 - Transmission of "Check Digit"
Resolution of Inconsistencies
Three types of inconsistencies could arise in the assignment of symbology options. The decoder has pre-defined strategies to resolve these inconsistencies: If UPCE_as_EAN13 is true, then UPCE_as_UPCA is ignored.
If symbology conversion is selected but the target symbology is not enabled, then the decoder still outputs the symbol in the target symbology. For example, suppose UPC-E is enabled and UPCE_as_EAN13 is true but EAN-13 is disabled. All UPC-E symbols will be shown as EAN-13 and EAN-13 options (if specified) will be applied. For the two symbologies that have optional check digits, Code39 and Interleave 2 of 5, the decoder will always transmit the check digit if the verification is disabled.
Verify Check
Digit
Return Check
Digit
Description
Enabled
Enabled
Disabled
Disabled
Enabled
Check digit is verified but is not transmitted
Check digit is verified and is transmitted
Table 13 - Resolution of Inconsistencies
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
132
KDC User Manual B ARCODE & S CAN O PTIONS
10.3 Miscellaneous Barcode Information
Height of a Linear Barcode
Industry standards suggest a height of either 6.5mm or 15% of the symbol length, whichever is greater. Symbols of less than recommended heights may cause recognition problems.
Check Characters
Yes, we recommend the use of check-characters in barcodes. Operating without checkcharacters is not safe and will lead to errors that are costly to correct. Using checkcharacters positively affects data integrity, especially when character density is at the limits and/or image quality is not at its best.
Prevent Interleave 2 of 5 Partial Reading
A partial scan of an Interleave 2 of 5 symbols may decode and cause incorrect data to be read. To prevent partial scans on long symbols, the user should include bearer bars.
These bars run along the top and bottom edges of the barcode in the scanning direction.
If a partial scan of the barcode occurs, the scanning beam will hit the bearer bar and will not decode. The bearer bar must touch the top and bottom of all the bars and must be at least 3 times as wide.
Another solution for the short scanning problem is to fix all Interleave 2 of 5 symbols to a set number of digits. Zeros can be used to pad the data to the set number of digits. The application program would then be set to only accept scans of the correct number of digits.
Finally, a check digit may be used. The Interleave 2 of 5 symbology has an optional check character that uses a weighted Modulo 10 scheme. The check character is the last character in the symbol and should be checked by the decoder and then transmitted with the data. Since Interleave 2 of 5 must always have an even number of digits, the leftmost character may need to be a zero when the check character is added. The standard check digit is calculated by assigning alternating 3,1,3,1… weights to respective data digits.
These weights are then multiplied by their respective data digits and the products are summed. The check digit is the digit that needs to be added to the sum to make it an even multiple of 10. An example would be if the sum of the products was 37, then the check digit would be 3.
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
KDC User Manual B ARCODE & S CAN O PTIONS
Equation to Determining Potential Number of Stored Barcodes
The number of barcodes that can be stored in the KDC memory depends on the size of the barcodes.
Example: If only UPCA barcodes are scanned and the check digit is not transmitted, then each barcode takes up 11 (barcode data) + 2 (added bytes) + 2 (length and type) + 4
(time stamp) = 19 bytes. The maximum number of UPCA barcodes that can be saved is
204,800/19 =10,778. However, KDC has limited the maximum number of barcode to
10,240 and users cannot store more than 10,240 barcodes in 2.85/86 version. 3.0x version allows the user to store maximum 204,800 barcodes.
Data Buffer Full
When the data buffer is full, the KDC displays a message, Buffer Full, ignoring any command to scan barcodes. The user must reset the data buffer to continue data collection.
133
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
134
KDC User Manual FQA
11. Appendix B –FAQ
11.1 Symbology
Q: What barcode symbologies are supported by the KDC?
A: The KDC20/100/200/250/350L/410/415 support 1D barcode only.
KDC30/300/350C/420/425/450 support most major 1D, 2D barcode symbologies and OCR.
KDC30/300/420/425
2D Barcodes
AztecCode, AztecRunes, CodablockF,
Code16K, Code49, DataMatrix,
MaxiCode, MicroPDF, PDF417,
QRCode, and HanXin Code
1D Barcodes
Codabar, Code11, Code32, Code39,
Code128, EAN8, EAN13, GS1-128,
I2of5, MSI, Plessey, PosiCode, GS1
DATABAR OMNI, GS1 Limited, GS1
Expanded, S2of5IA, S2of5ID, TLC39,
Telepen, Trioptic, UPCA, and UPCE
Postal Barcodes
AusPost, CanadaPost, ChinaPost,
JapanPost, KoreaPost, KixPost, Planet
Code, Postnet (US), and UKPost
OCR Fonts
OCR-A, OCR-B, OCRUSCurrency,
OCRMICRE13B, and OCRSEMIFONT
KDC20/100/200/250/410/415
1D Barcodes
EAN13
EAN8
UPCA
UPCE
Bookland EAN
EAN13 with Add-on
EAN8 with Add-on
UPCA with Add-on
UPCE with Add-on
Interleave 2 of 5
ITF14
Code128
Codabar
GS1-128
Code39
Code93
Code35
Table 14 – Symbologies supported by KDC
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
135
KDC User Manual FQA
11.2 Host Interface
Q: What interface ports are supported by the KDC?
A: The KDC100 has two USB ports: Swing-out Type A and ultra mini USB ports that support USB to Serial protocol. KDC200/250/300/350/400 have one ultra mini USB port that supports USB to Serial protocol and Bluetooth that supports HID/SPP/MFi
Bluetooth
profiles. KDC20/30 have one Swing-out Type A USB port which supports USB to Serial protocol and Bluetooth with HID, SPP and MFi
Bluethooth
profiles.
11.3 Battery
Q: How long will the KDC battery last before it needs to be replaced?
A: The battery on the KDC can be charged at least 300 times before it needs to be replaced.
Q: How long does it take to charge the KDC?
A: It takes about 2 hours to charge the KDC20/100/200, 4 hours to charge the
KDC30/250/300, and 5 hours to charge the KDC350/400.
Q: How many barcodes can a fully charged KDC scan?
A: If the user scans a barcode every 1 seconds, KDC100 scans more than 15,000 barcodes,
KDC20 scans more than 9,000 barcodes, KDC200 scans more than 7,500 barcodes,
KDC250 scans more than 25,000 scans, KDC30/300 scans more than 20,000 scans and
KDC350/400 scan more than 40,000.
Q: How long will the KDC battery lasts in the sleep mode?
A: KDC100 lasts more than 75 days. KDC20/200 lasts more than 2 days while connected in
Bluetooth and 60 days if not connected in Bluetooth. KDC250 lasts 7 days while connected in Bluetooth and 120 days if not connected in Bluetooth. KDC30/300 last more than 25 days while connected in Bluetooth and 5 days if not connected in Bluetooth.
KDC350 lasts more than 12 hours while GPS is active and Bluetooth is connected, 7 days while GPS is not active and Bluetooth is connected, and 20 days while GPS is not active and Bluetooth is not connected. KDC410/415/420/425/430 last more than 8 days while connected in Bluetooth and 20 days while if not connected in Bluetooth. KDC450 lasts more than 4 hours while reading RFiD tag continuously every second and Bluetooth is connected, 5 days if reading RFiD tag casually and Bluetooth is connected.
Q: Can I replace the KDC battery?
A: Yes. The KDC has a separate compartment for the battery that can be opened easily with a driver. KDC batteries can be purchased at www.KOAMTACstore.com
or from local
KDC reseller.
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
136
KDC User Manual FQA
11.4 Memory
Q: How many barcodes can be stored in the KDC?
A: KDC100M/200M/250M/300M/350 have 4MB data memory which can store maximum of
204,800 barcodes. KDC20/30 have 160KB data memory which can store maximum 10,240 barcodes. KDC400 has 100KB data memory.
Q: Can I download stored barcodes or wedge barcodes to my application?
A: Yes. KTSync ® is keyboard wedging, application generation, DB look up, and inventory program bundled with the KDC200/250/300/350, which supports host devices running on
Android ® , iPhone/iPad/iPod touch, Blackberry ® , Windows ® XP/Vista/7/Mobile5.0+.
KTSync ® provides keyboard wedging program only for KDC20/30/400 and KDC100 only supports Windows XP/Vista/7 version.
Q: Does the KDC support
Android
Windows
® devices?
® ,
iPhone/iPad/iPod touch
® ,
Blackberry
® , Mac ® and
A: KTSync ® currently supports Android ® , iPhone/iPad/iPod touch, Blackberry ® , Mac ® and
Windows ® devices.
11.5 Programming
Q: Can the KDC be programmed by a KOAMTAC partner?
A: Yes. KOAMTAC’s Application Generation tool provides an enhanced programming environment for developing custom applications for the KDC.
1. KDC supports, at most, three step data collection processes, including the ability to perform various data functionality features.
2. KDC’s database lookup function provides enhanced data processes, enabling the
KDC to display database results with or without scanned barcode data.
3. KDC can display a message from the Host by enabling two-way communications and a messaging application.
Q: Does KOAMTAC provide customization services for the KDC?
A: Yes. Custom applications or projects can be developed by KOAMTAC engineers. This service is provided for an additional fee to KOAMTAC. For more information regarding this service, please contact KOAMTAC.
Q: Can a partner develop a PC or Smartphone application for the KDC?
A: A software development kit for Windows ® XP/Vista/7/Mobile5.0+ and Android is available on KOAMTAC support page. Android ® , iPhone/iPad/iPod touch, Blackberry ® , and Mac ® SDK are available through KOAMTAC authorized distributors.
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
137
KDC User Manual 1D S PECIAL B ARCODES
12. Appendix C – 1D Special Barcodes
(KDC20/100/200/250/350L/410/415)
12.1 Set Symbologies
Enable EAN13 Disable EAN13
Enable EAN8
Enable UPCA
Enable UPCE
Enable Code39
Enable ITF14
Disable EAN8
Disable UPCA
Disable UPCE
Disable Code39
Disable ITF14
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
138
KDC User Manual 1D S PECIAL B ARCODES
Enable Code128 Disable Code128
Enable I2 of 5
Enable Codabar
Disable I2 of 5
Disable Codabar
Enable GS1-128
Enable Code93
Enable Code35
Enable Bookland EAN
Enable EAN13 with Addon
Disable GS1-128
Disable Code93
Disable Code35
Disable Bookland EAN
Disable EAN13 with Addon
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
KDC User Manual 1D S PECIAL B ARCODES
Enable EAN8 with Addon Disable EAN8 with Addon
Enable UPCA with Addon
Enable UPCE with Addon
Disable UPCA with Addon
Disable UPCE with Addon
139
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
140
KDC User Manual 1D S PECIAL B ARCODES
12.2 Barcode Options
Codabar - do NOT transmit start/stop Codabar - transmit start/stop
Convert UPCE to UPCA
Convert EAN8 to EAN13
Convert UPCE to EAN13
Return Check Digit
Verify Check Digit
Convert UPCA to EAN13
Do NOT convert UPCE to UPCA
Do NOT convert EAN8 to EAN13
Do NOT convert UPCE to EAN13
Do NOT Return Check Digit
Do NOT Verify Check Digit
Do NOT Convert UPCA to EAN13
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
141
KDC User Manual 1D S PECIAL B ARCODES
Verify check digit for I2of5 Do NOT verify check digit for I2of5
Verify check digit for Code39
Return check digit for I2of5
Return check digit for Code39
Return check digit for UPCE
Return check digit for UPCA
Do NOT verify check digit for Code39
Do NOT return check digit for I2of5
Do NOT return check digit for Code39
Do NOT return check digit for UPCE
Do NOT return check digit for UPCA
Return check digit for EAN8 Do NOT return check digit for EAN8
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
KDC User Manual 1D S PECIAL B ARCODES
Return check digit for EAN13 Do NOT return check digit for EAN13
142
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
143
KDC User Manual 1D S PECIAL B ARCODES
12.3 Delete Last Scanned Barcode
Delete Last Scanned Barcode
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
144
KDC User Manual 1D S PECIAL B ARCODES
12.4 Scan Options
Wide Scan Angle Narrow Scan Angle
Normal Filter Mode
Enable Auto Trigger
Reread Delay = Continuous
Reread Delay = Medium
Reread Delay = Extra Long
High Filter Mode
Disable Auto Trigger
Reread Delay = Short
Reread Delay = Long
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
145
KDC User Manual 1D S PECIAL B ARCODES
12.5 Scan Timeout
Scan Timeout = 500msec Scan Timeout = 1sec
Scan Timeout = 2sec
Scan Timeout = 4sec
Scan Timeout = 6sec
Scan Timeout = 8sec
Scan Timeout = 10sec
Scan Timeout = 3sec
Scan Timeout = 5sec
Scan Timeout = 7sec
Scan Timeout = 9sec
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
146
KDC User Manual 1D S PECIAL B ARCODES
12.6 Minimum Barcode Length
Minimum Length = 2 Minimum Length = 3
Minimum Length = 4
Minimum Length = 6
Minimum Length = 8
Minimum Length = 10
Minimum Length = 12
Minimum Length = 14
Minimum Length = 5
Minimum Length = 7
Minimum Length = 9
Minimum Length = 11
Minimum Length = 13
Minimum Length = 15
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
147
KDC User Manual 1D S PECIAL B ARCODES
Minimum Length = 16 Minimum Length = 17
Minimum Length = 18
Minimum Length = 20
Minimum Length = 22
Minimum Length = 24
Minimum Length = 26
Minimum Length = 19
Minimum Length = 21
Minimum Length = 23
Minimum Length = 25
Minimum Length = 27
Minimum Length = 28 Minimum Length = 29
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
148
KDC User Manual 1D S PECIAL B ARCODES
Minimum Length = 30 Minimum Length = 31
Minimum Length = 32
Minimum Length = 34
Minimum Length = 36
Minimum Length = 33
Minimum Length = 35
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
149
KDC User Manual 1D S PECIAL B ARCODES
12.7 Security Level
Security level = 1 Security level = 2
Security level = 3 Security level = 4
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
150
KDC User Manual 1D S PECIAL B ARCODES
12.8 Data Process - Wedge/Store & Enter Key
Wedge Only Wedge & Store Always
Store Only
Save if Not Sent
Enable Enter Key (KDC350L Only)
Save if Sent
Disable Enter Key (KDC350L Only)
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
151
KDC User Manual 1D S PECIAL B ARCODES
12.9 Data Process - Data Edit
Start Prefix Enter Start Suffix Enter
Finish Prefix/Suffix Enter
Delete Prefix
Display Prefix
AIM ID None
AIM ID In Suffix
Cancel Prefix/Suffix Enter
Delete Suffix
Display Suffix
AIM ID In Prefix
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
KDC User Manual 1D S PECIAL B ARCODES
12.10 Data Process - Data Format & Handshake
Data format = Barcode only Data format = Packet data
Enable Handshake Disable Handshake
152
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
153
KDC User Manual 1D S PECIAL B ARCODES
12.11 Data Process - Termination Character
& Duplicate Check
Termination Character = None Termination Character = CR
Termination Character = LF
Termination Character = Tab
Enable Duplicate Check
Termination Character = CR+LF
Disable Duplicate Check
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
154
KDC User Manual 1D S PECIAL B ARCODES
12.12 Bluetooth
Enable Bluetooth Power Disable Bluetooth Power
Enter Pairing Mode
Enable Discovering
Connect To Last
Disconnect
HID Sync
Bluetooth Profile = SPP
Disable Discovering
Connecting to
SPP Sync
Bluetooth Profile = HID iOS
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
155
KDC User Manual 1D S PECIAL B ARCODES
Bluetooth Profile = IPHONE Bluetooth Profile = SPP2.0
Bluetooth Profile = HID Normal
Enable Auto Connect
Enable Auto Reconnect
Enable Auto Power On
Enable Auto Power Off
Enable Beep Warning
Enable Power Off Msg
Disable Auto Connect
Disable Auto Reconnect
Disable Auto Power On
Disable Auto Power Off
Disable Beep Warning
Disable Power Off Msg
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
KDC User Manual 1D S PECIAL B ARCODES
Display BT MAC Address Display BT FW Version
Enable Wakeup Nulls Disable Wakeup Nulls
Disable BT Toggle
Disable BT Disconnect Button
Enable BT Toggle
Enable BT Disconnect Button
156
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
157
KDC User Manual 1D S PECIAL B ARCODES
12.13 Bluetooth Auto Power On Time
Auto Power On Time = Disabled Auto Power On Time = 1sec
Auto Power On Time = 2sec
Auto Power On Time = 4sec
Auto Power On Time = 6sec
Auto Power On Time = 8sec
Auto Power On Time = 10sec
Auto Power On Time = 3sec
Auto Power On Time = 5sec
Auto Power On Time = 7sec
Auto Power On Time = 9sec
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
158
KDC User Manual 1D S PECIAL B ARCODES
12.14 Bluetooth Power Off Time
BT Power Off Time = 1min BT Power Off Time = 2min
BT Power Off Time = 3min
BT Power Off Time = 5min
BT Power Off Time = 7min
BT Power Off Time = 9min
BT Power Off Time = 11min
BT Power Off Time = 13min
BT Power Off Time = 4min
BT Power Off Time = 6min
BT Power Off Time = 8min
BT Power Off Time = 10min
BT Power Off Time = 12min
BT Power Off Time = 14min
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
159
KDC User Manual 1D S PECIAL B ARCODES
BT Power Off Time = 15min BT Power Off Time = 16min
BT Power Off Time = 17min BT Power Off Time = 18min
BT Power Off Time = 19min
BT Power Off Time = 21min
BT Power Off Time = 23min
BT Power Off Time = 25min
BT Power Off Time = 27min
BT Power Off Time = 29min
BT Power Off Time = 20min
BT Power Off Time = 22min
BT Power Off Time = 24min
BT Power Off Time = 26min
BT Power Off Time = 28min
BT Power Off Time = 30min
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
160
KDC User Manual 1D S PECIAL B ARCODES
12.15 HID Auto Lock Time
HID Auto Lock Time = 0min (Never) HID Auto Lock Time = 1min
HID Auto Lock Time = 2min
HID Auto Lock Time = 4min
HID Auto Lock Time = 10min
HID Auto Lock Time = 3min
HID Auto Lock Time = 5min
HID Auto Lock Time = 15min
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
KDC User Manual 1D S PECIAL B ARCODES
12.16 HID Keyboard
HID Keyboard = US HID Keyboard = German
HID Keyboard = French
HID Keyboard = Spanish
HID Keyboard = Italian
161
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
KDC User Manual 1D S PECIAL B ARCODES
12.17 HID Initial Delay
HID Initial Delay = Disabled HID Initial Delay = 1second
HID Initial Delay = 2seconds HID Initial Delay = 3seconds
HID Initial Delay = 5seconds HID Initial Delay = 10seconds
162
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
KDC User Manual 1D S PECIAL B ARCODES
12.18 HID Character Delay
HID Character Delay = Disabled HID Character Delay = 10msec
HID Character Delay = 20msec
HID Character Delay = 50msec
HID Character Delay = 30msec
HID Character Delay = 100msec
163
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
KDC User Manual 1D S PECIAL B ARCODES
12.19 HID Control Character
HID Control Character = Disabled HID Control Character = Alt+Numpad
HID Control Character = ^+Character HID Control Character = Replace with ‘|’
164
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
165
KDC User Manual 1D S PECIAL B ARCODES
12.20 System
Memory Size = 0.5M / 3.5M
Memory Size = 1M / 3M
Memory Size = 2M / 2M
Memory Size = 4M / 0M
Memory Status
Erase Memory
Reset BT Registry
Enable Auto Erase
Memory Size = 3M / 1M
Confirm Memory Size Change
Reset Memory
Reset App data
Disable Auto Erase
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
166
KDC User Manual 1D S PECIAL B ARCODES
Date/Time Battery
Display Version
Lock Button
Enable Beep Sound
High Beep Volume
Enable Auto Menu Exit
Enable MFi Mode
Enable Vibrator
Unlock Button
Disable Beep Sound
Low Beep Volume
Disable Auto Menu Exit
Disable MFi Mode
Disable Vibrator
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
167
KDC User Manual 1D S PECIAL B ARCODES
Enable Port Status Disable Port Status
Display Format = Time & Battery Display Format = Type & Time
Display Format = Type & Battery
Display Format = GPS Data (GPS Model)
Display Format = Memory Status
Display Format = Barcode Only
Enable Scrolling
Factory Default
Disable Scrolling
KDC Reset
Enable Backup Battery (KDC20 Only) Disable Backup Battery (KDC20 Only)
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
168
KDC User Manual 1D S PECIAL B ARCODES
12.21 Sleep Timeout
Sleep Timeout = Disable Sleep Timeout = 1sec
Sleep Timeout = 2sec
Sleep Timeout = 4sec
Sleep Timeout = 10sec
Sleep Timeout = 30sec
Sleep Timeout = 2min
Sleep Timeout = 10min
Sleep Timeout = 3sec
Sleep Timeout = 5sec
Sleep Timeout = 20sec
Sleep Timeout = 1min
Sleep Timeout = 5min
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
169
KDC User Manual 1D S PECIAL B ARCODES
12.22 ETC
Enable Reverse Direction Disable Reverse Direction
Enable Verify check digit
Enable Return check digit
Disable Verify check digit
Disable Return check digit
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
170
KDC User Manual 1D S PECIAL B ARCODES
12.23 Function
F1 F2
F3 F4
F5 F6
F7
F9
F8
F10
F11 F12
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
171
KDC User Manual 1D S PECIAL B ARCODES
12.24 Number
0 1
2
4
3
5
6
8
7
9
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
172
KDC User Manual 1D S PECIAL B ARCODES
12.25 Lower Case Alphabet
a b c e g i k m d f h j l n
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
173
KDC User Manual 1D S PECIAL B ARCODES o p q r s u w y t v x z
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
174
KDC User Manual 1D S PECIAL B ARCODES
12.26 Upper Case Alphabet
A B
C
E
G
I
K
M
D
F
H
J
L
N
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
175
KDC User Manual 1D S PECIAL B ARCODES
O P
Q R
S
U
W
Y
T
V
X
Z
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
176
KDC User Manual 1D S PECIAL B ARCODES
12.27 Control Character
BS TAB
LF
CR
Space
Shift + Tab
VT
ESC
DEL
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
177
KDC User Manual 1D S PECIAL B ARCODES
12.28 Symbol Character
! “
#
%
‘
)
+
-
*
,
.
$
&
(
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
178
KDC User Manual 1D S PECIAL B ARCODES
/ :
;
=
?
[
]
<
>
@
\
^
_ `
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
179
KDC User Manual 1D S PECIAL B ARCODES
{ |
}
Start String
~
Stop String
Note
The user can compose a string up to 16 characters.
A string would be composed by scanning the “Start-String”, number/alphabet/special characters, and “Stop-String” special barcodes.
The KDC will abort string composition if the user do not scan
“Stop-String” in one minute after scanning “Start-String” and number/alphabet/special characters.
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
180
KDC User Manual 1D S PECIAL B ARCODES
12.29 GPS (GPS Model Only)
Enable GPS Power Disable GPS Power
Enable GPS Bypass Data Disable GPS Bypass Data
Reset GPS Module GPS Acquire Test
GPS Power Save Mode = Normal GPS Power Save Mode = Power Saving
Enable GPS Auto Power Off Disable GPS Auto Power Off
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
KDC User Manual 1D S PECIAL B ARCODES
12.30 GPS/BT Auto Power Off Timeou
Auto Power Off = 0min (Disabled) Auto Power Off = 5min
Auto Power Off = 10min
Auto Power Off = 30min
Auto Power Off = 120min
Auto Power Off = 20min
Auto Power Off = 60min
181
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
KDC User Manual 1D S PECIAL B ARCODES
12.31 NFC (NFC Model Only)
Enable NFC Power Disable NFC Power
NFC Data Format = Data only
UID Only = Enable
NFC Data Format = Packet data
UID Only = Disable
182
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
183
KDC User Manual 1D S PECIAL B ARCODES
12.32 USB Disk (M Model Only)
USB Serial Mode USB Disk Mode
Format USB Disk
Data Format = Data Data Format = Data, Time
Data Format = Data, Time, Type Data Format = Data, Type
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
184
KDC User Manual 2D S PECIAL B ARCODES
13. Appendix D – 2D Special
Barcodes (KDC30/300/350C/420
/425/450)
13.1 Set Symbologies
Please refer to Honeywell Adaptus ® Technology enabled scanner user manual, such as
4600 or 4820.
13.2 Barcode Options
Please refer to Honeywell Adaptus ® Technology enabled scanner user manual, such as
4600 or 4820.
13.3 Delete Last Scanned Barcode
Delete Last Scanned Barcode
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
KDC User Manual 2D S PECIAL B ARCODES
13.4 Scan Options
Enable Auto Trigger Disable Auto Trigger
Reread Delay = Continuous
Reread Delay = Medium
Reread Delay = Extra Long
Reread Delay = Short
Reread Delay = Long
185
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
186
KDC User Manual 2D S PECIAL B ARCODES
13.5 Scan Timeout
Scan Timeout = 500msec Scan Timeout = 1sec
Scan Timeout = 2sec Scan Timeout = 3sec
Scan Timeout = 4sec Scan Timeout = 5sec
Scan Timeout = 6sec Scan Timeout = 7sec
Scan Timeout = 8sec Scan Timeout = 9sec
Scan Timeout = 10sec
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
187
KDC User Manual 2D S PECIAL B ARCODES
13.6 Minimum Barcode Length
Minimum Length = 2 Minimum Length = 3
Minimum Length = 4
Minimum Length = 6
Minimum Length = 8
Minimum Length = 5
Minimum Length = 7
Minimum Length = 9
Minimum Length = 10
Minimum Length = 12
Minimum Length = 14
Minimum Length = 11
Minimum Length = 13
Minimum Length = 15
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
188
KDC User Manual 2D S PECIAL B ARCODES
Minimum Length = 16 Minimum Length = 17
Minimum Length = 18
Minimum Length = 20
Minimum Length = 22
Minimum Length = 24
Minimum Length = 26
Minimum Length = 28
Minimum Length = 19
Minimum Length = 21
Minimum Length = 23
Minimum Length = 25
Minimum Length = 27
Minimum Length = 29
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
KDC User Manual 2D S PECIAL B ARCODES
Minimum Length = 30 Minimum Length = 31
Minimum Length = 32 Minimum Length = 33
Minimum Length = 34
Minimum Length = 36
Minimum Length = 35
189
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
KDC User Manual 2D S PECIAL B ARCODES
13.7 Image Capture
Capture Now Enable Image Capture
Image Format = JPEG Image Format = BMP
Pixel Depth = 1 bit per pixel Pixel Depth = 8 bit per pixel
190
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
191
KDC User Manual 2D S PECIAL B ARCODES
13.8 Data Process - Wedge/Store & Enter Key
Wedge Only Wedge & Store Always
Store Only
Save if Not Sent
Enable Enter Key (KDC350C Only)
Save if Sent
Disable Enter Key (KDC350C Only)
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
192
KDC User Manual 2D S PECIAL B ARCODES
13.9 Data Process - Data Edit
Start Prefix Enter Start Suffix Enter
Finish Prefix / Suffix Enter
Delete Prefix
Display Prefix
AIM ID None
AIM ID In Suffix
Cancel Prefix / Suffix Enter
Delete Suffix
Display Suffix
AIM ID In Prefix
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
KDC User Manual 2D S PECIAL B ARCODES
13.10 Data Process – Data Format & Handshake
Data format = Barcode only Data format = Packet data
Enable Handshake Disable Handshake
193
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
194
KDC User Manual 2D S PECIAL B ARCODES
13.11 Data Process - Termination Character &
Duplicate Check
Termination Character = None Termination Character = CR
Termination Character = LF
Termination Character = Tab
Enable Duplicate Check
Termination Character = CR+LF
Disable Duplicate Check
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
195
KDC User Manual 2D S PECIAL B ARCODES
13.12 Bluetooth
Enable Bluetooth Power Disable Bluetooth Power
Enter Pairing Mode
Enable Discovering Disable Discovering
Connect To Last Connect To
Disconnect
HID Sync SPP Sync
Bluetooth Profile = SPP Bluetooth Profile = HID iOS
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
196
KDC User Manual 2D S PECIAL B ARCODES
Bluetooth Profile = IPHONE Bluetooth Profile = SPP2.0
Bluetooth Profile = HID Normal
Enable Auto Connect
Enable Auto Reconnect
Enable Auto Power Off
Enable Auto Power On
Enable Beep Warning
Disable Auto Connect
Disable Auto Reconnect
Disable Auto Power Off
Disable Auto Power On
Disable Beep Warning
Enable Power Off Msg Disable Power Off Msg
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
KDC User Manual 2D S PECIAL B ARCODES
Display BT Mac Address Display BT FW Version
Enable Wakeup Nulls
Enable BT Toggle
Enable BT Disconnect Button
Disable Wakeup Nulls
Disable BT Toggle
Disable BT Disconnect Button
197
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
198
KDC User Manual 2D S PECIAL B ARCODES
13.13 Bluetooth Auto Power On Time
Auto Power On Time = Disabled Auto Power On Time = 1sec
Auto Power On Time = 2sec Auto Power On Time = 3sec
Auto Power On Time = 4sec Auto Power On Time = 5sec
Auto Power On Time = 6sec Auto Power On Time = 7sec
Auto Power On Time = 8sec Auto Power On Time = 9sec
Auto Power On Time = 10sec
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
199
KDC User Manual 2D S PECIAL B ARCODES
13.14 Bluetooth Power Off Time
BT Power Off Time = 1min BT Power Off Time = 2min
BT Power Off Time = 3min
BT Power Off Time = 5min
BT Power Off Time = 7min
BT Power Off Time = 9min
BT Power Off Time = 11min
BT Power Off Time = 4min
BT Power Off Time = 6min
BT Power Off Time = 8min
BT Power Off Time = 10min
BT Power Off Time = 12min
BT Power Off Time = 13min BT Power Off Time = 14min
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
200
KDC User Manual 2D S PECIAL B ARCODES
BT Power Off Time = 15min BT Power Off Time = 16min
BT Power Off Time = 17min
BT Power Off Time = 19min
BT Power Off Time = 18min
BT Power Off Time = 20min
BT Power Off Time = 21min
BT Power Off Time = 23min
BT Power Off Time = 25min
BT Power Off Time = 22min
BT Power Off Time = 24min
BT Power Off Time = 26min
BT Power Off Time = 27min BT Power Off Time = 28min
BT Power Off Time = 29min BT Power Off Time = 30min
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
KDC User Manual 2D S PECIAL B ARCODES
13.15 HID Auto Lock Time
HID Auto Lock Time = 0min (Never) HID Auto Lock Time = 1min
HID Auto Lock Time = 2min
HID Auto Lock Time = 4min
HID Auto Lock Time = 10min
HID Auto Lock Time = 3min
HID Auto Lock Time = 5min
HID Auto Lock Time = 15min
201
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
KDC User Manual 2D S PECIAL B ARCODES
13.16 HID Keyboard
HID Keyboard = US HID Keyboard = German
HID Keyboard = French
HID Keyboard = Spanish
HID Keyboard = Italian
202
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
KDC User Manual 2D S PECIAL B ARCODES
13.17 HID Initial Delay
HID Initial Delay = Disabled HID Initial Delay = 1second
HID Initial Delay = 2seconds HID Initial Delay = 3seconds
HID Initial Delay = 5seconds HID Initial Delay = 10seconds
203
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
KDC User Manual 2D S PECIAL B ARCODES
13.18 HID Character Delay
HID Character Delay = Disabled HID Character Delay = 10msec
HID Character Delay = 20msec HID Character Delay = 30msec
HID Character Delay = 50msec HID Character Delay = 100msec
204
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
KDC User Manual 2D S PECIAL B ARCODES
13.19 HID Control Character
HID Control Character = Disabled HID Control Character = Alt+Numpad
HID Control Character = ^+Character HID Control Character = Replace with ‘|’
205
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
206
KDC User Manual 2D S PECIAL B ARCODES
13.20 System
Memory Size = 0.5M / 3.5M
Memory Size = 1M / 3M
Memory Size = 2M / 2M
Memory Size = 4M / 0M
Memory Status
Erase Memory
Reset BT Registry
Enable Auto Erase
Memory Size = 3M / 1M
Confirm memory size
Reset Memory
Reset App data
Disable Auto Erase
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
207
KDC User Manual 2D S PECIAL B ARCODES
Date/Time Battery
Display Version
Lock Button
Enable Beep Sound
High Beep Volume
Enable MFi Mode
Unlock Button
Disable Beep Sound
Low Beep Volume
Disable MFi Mode
Enable Vibrator
Enable Auto Menu Exit
Disable Vibrator
Disable Auto Menu Exit
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
208
KDC User Manual 2D S PECIAL B ARCODES
Enable Port Status Disable Port Status
Display Format = Time & Battery Display Format = Type & Time
Display Format = Type & Battery Display Format = Memory Status
Display Format = GPS Data(GPS Model) Display Format = Barcode Only
Enable Menu Barcode Disable Menu Barcode
Enable Scrolling
Factory Default
Disable Scrolling
KDC Reset
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
209
KDC User Manual 2D S PECIAL B ARCODES
13.21 Sleep Timeout
Sleep Timeout = Disable Sleep Timeout = 1sec
Sleep Timeout = 2sec
Sleep Timeout = 4sec
Sleep Timeout = 10sec
Sleep Timeout = 30sec
Sleep Timeout = 2min
Sleep Timeout = 10min
Sleep Timeout = 3sec
Sleep Timeout = 5sec
Sleep Timeout = 20sec
Sleep Timeout = 1min
Sleep Timeout = 5min
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
210
KDC User Manual 2D S PECIAL B ARCODES
13.22 Function
F1 F2
F3 F4
F5 F6
F7 F8
F9 F10
F11 F12
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
211
KDC User Manual 2D S PECIAL B ARCODES
13.23 Number
0 1
2 3
4 5
6 7
8 9
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
212
KDC User Manual 2D S PECIAL B ARCODES
13.24 Lower Case Alphabet
a b c d e f g h j i k l m n
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
213
KDC User Manual 2D S PECIAL B ARCODES o p q s u w y r t v x z
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
214
KDC User Manual 2D S PECIAL B ARCODES
13.25 Upper Case Alphabet
A B
C D
E F
G H
I J
K L
M N
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
215
KDC User Manual 2D S PECIAL B ARCODES
O P
Q R
S T
U V
W X
Y Z
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
216
KDC User Manual 2D S PECIAL B ARCODES
13.26 Control Character
BS TAB
LF VT
CR ESC
Space DEL
Shift + Tab
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
217
KDC User Manual 2D S PECIAL B ARCODES
13.27 Symbol Character
! “
# $
% &
‘ (
) *
+ ,
- .
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
218
KDC User Manual 2D S PECIAL B ARCODES
/ :
; <
= >
? @
[ \
] ^
_ `
{ |
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
219
KDC User Manual 2D S PECIAL B ARCODES
} ~
Start String
Stop String
Note
The user can compose a string up to 16 characters.
A string would be composed by scanning the “Start-String”, number/alphabet/special characters, and “Stop-String” special barcodes.
The KDC will abort string composition if the user do not scan
“Stop-String” in one minute after scanning “Start-String” and number/alphabet/special characters.
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
220
KDC User Manual 2D S PECIAL B ARCODES
13.28 GPS (GPS Model Only)
Enable GPS Power Disable GPS Power
Enable GPS Bypass Data Disable GPS Bypass Data
Reset GPS Module
GPS Power Save Mode = Normal
Enable GPS Auto Power Off
GPS Acquire Test
GPS Power Save Mode = Power Saving
Disable GPS Auto Power Off
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
221
KDC User Manual 2D S PECIAL B ARCODES
13.29 GPS/BT Auto Power Off Timeot
Auto Power Off = 0min (Disabled) Auto Power Off = 5min
Auto Power Off = 10min
Auto Power Off = 30min
Auto Power Off = 20min
Auto Power Off = 60min
Auto Power Off = 120min
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
222
KDC User Manual 2D S PECIAL B ARCODES
13.30 NFC (NFC Model Only)
Enable NFC Power Disable NFC Power
NFC Data Format = Data only NFC Data Format = Packet data
UID Only = Enable UID Only = Disable
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
KDC User Manual 2D S PECIAL B ARCODES
13.31 USB Disk (M Model Only)
USB Serial Mode USB Disk Mode
Format USB Disk
Data Format = Data
Data Format = Data,Type
Data Format = Data,Time
Data Format = Data,Time,Type
223
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
224
KDC User Manual MSR S PECIAL B ARCODES
14. APPENDIX E - MSR Special Barcodes
(KDC415/425MSR)
14.1 KDC415MSR
Beep On Error
No Beep On Error Beep On Error
MSR Data Only
Data Format
Packet data
Disabled
Encrypt Mode
AES
Enable Track1
Enable Track
Enable Track2
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
225
KDC User Manual MSR S PECIAL B ARCODES
Enable Track3
Disable Track
Disable Track1 Disable Track2
Disable Track3
Track Separator = None
Track Separator
Track Separator = Space
Track Separator = Comma Track Separator = Semi Colon
Track Separator = CR
Track Separator = CR+LF
Track Separator = LF
Track Separator = Tab
AES Key Length
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
226
KDC User Manual MSR S PECIAL B ARCODES
AES Key Length = 128 bits AES Key Length = 192 bits
AES Key Length = 256 bits
MSR Card Type = ISO
MSR Card Type
MSR Card Type = Other 1
MSR Card Type = AAMVA
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
227
KDC User Manual MSR S PECIAL B ARCODES
14.2 KDC425MSR
Beep On Error
No Beep On Error Beep On Error
Data Format
MSR Data Only Packet data
Encrypt Mode
Disabled AES
Enable Track
Enable Track1 Enable Track2
Enable Track3
Disable Track
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
228
KDC User Manual MSR S PECIAL B ARCODES
Disable Track1 Disable Track2
Disable Track3
Track Separator = None
Track Separator
Track Separator = Space
Track Separator = Comma Track Separator = Semi Colon
Track Separator = CR Track Separator = LF
Track Separator = CR+LF
AES Key Length
Track Separator = Tab
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
KDC User Manual MSR S PECIAL B ARCODES
AES Key Length = 128 bits AES Key Length = 192 bits
AES Key Length = 256 bits
MSR Card Type = ISO
MSR Card Type
MSR Card Type = Other 1
MSR Card Type = AAMVA
229
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
230
KDC User Manual M ULTIPLE S PECIAL B ARCODES
15. Appendix F – Multiple Special
Barcodes
This chapter explains how to make a multiple configuration barcode for the KDC to configure multiple KDC settings by scanning one barcode. The KDC provides special barcodes that enable changes to the KDC configuration; but, this current barcode changes only one configuration.
New KDC firmware VersionR_305 introduces a feature to enable the user to make one special barcode to change multiple KDC configurations.
15.1 KDC20/KDC100/KDC250/KDC350L/KDC410/K
DC415
Barcode type Code128 is used to make a single special barcode and its format is as follows:
<FNC3><Barcode String>
Here, the <FNC3> is a Code 128 control character and the <Barcode String> is an ASCII string for each
KDC configuration.
The multiple configuration Code128 barcode format is as follows and has a control character and series of barcode strings.
<FNC3><Barcode String 1>;;;;; <Barcode String N>
Here, the <FNC3> is a Code 128 control character and the <Barcode String 1> and <Barcode String
N> are an ASCII string for each KDC configuration. The ‘;’ is a separator for each configuration’s barcode string. Please see user manual for the <Barcode String> for KDC configuration.
Example: Assume the user is changing the following configurations with one barcode.
Change Wedge/Store to “Wedge Only” <FNC3>82000
Change Termination Character to “None” <FNC3>88000
Change Bluetooth “Auto PowerOff” to “Disabled” <FNC3>64010
<FNC3>82000;88000;64010
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
231
KDC User Manual M ULTIPLE S PECIAL B ARCODES
15.2 KDC30/KDC300/KDC350C/KDC420/KDC425/K
DC450
The following format is for a single configuration barcode format:
<SYN> M <CR> KDC <Barcode String>.
<SYN> is a control character 0x16 in hex format.
M is an ASCII character 0x4D in hex format.
<CR> is a control character 0x0d in hex format.
KDC is an ASCII string 0x4B 0x44 0x43 in hex format.
<Barcode String> is an ASCII string for each configuration
. is an ASCII string 0x2E in hex format that indicates the end of barcode.
The multiple configuration barcode string uses a repeated barcode string of each configuration in the following format:
<SYN>M<CR>KDC<Barcode String 1> ;;;;;; <Barcode String N> .
<SYN> is a control character 0x16 in hex format.
M is an ASCII character 0x4D in hex format.
<CR> is a control character 0x0d in hex format.
KDC is an ASCII string 0x4B 0x44 0x43 in hex format.
<Barcode String1> and <Barcode String N> are an ASCII string for each configuration
; is a separator between each barcode strings.
. is an ASCII string 0x2E in hex format that indicates the end of barcode.
Example: Assume the user is changing the following configurations with one barcode.
Change Wedge/Store to “Wedge Only” <SYN>M<CR>KDC82000.
Change Termination Character to “None” <SYN>M<CR>KDC 88000.
Change Bluetooth “Auto PowerOff” to “Disabled” <SYN>M<CR>KDC 64010.
<SYN>M<CR>KDC82000;88000;64010.
Code 128
QR code
Revision 3.05.R8.
Copyright®2014, KOAMTAC, Inc.
Descargar
Enlace público actualizado
Se ha actualizado el enlace público a tu chat. Puedes ver y gestionar tus enlaces de chat después del registro aquí.
Enlace público del documento
Anuncio