Mattel Disney/Pixar Cars 2 Bubble Mater Instruction Sheet
Add to My manuals6 Pages
Mattel Disney/Pixar Cars 2 Bubble Mater is a toy car that blows bubbles as it is pushed along. It is suitable for children and requires adult assembly. No tools are needed for assembly. The toy comes with bubble solution, and the bubble dispenser can be refilled when the solution runs out. The bubble chamber should not be overfilled to avoid leaking. To use the bubble dispenser, remove the cap and seal and insert it back into the engine. Slide the engine cover to access the bubble dispenser and attach the cap to the top of the bubble dispenser. Twist the dispenser to secure it to the cap.
advertisement
V7599
Please keep this instruction sheet for future reference, as it contains important information.
Adult assembly is required.
No tools needed for assembly.
www.fisher-price.com
IMPORTANT!
• Your toy includes bubble solution in the bubble dispenser. Once bubble solution is gone, do not remove or throw away the bubble dispenser that comes with this toy. Simply refill the bubble dispenser with bubble solution.
• Use only bubble solution in this toy.
• Make sure your child understands that bubble solution is not for drinking and that it should be kept away from the eyes.
• While filling or cleaning this toy, try to avoid spilling bubble solution on the floor. It may create slippery floor conditions.
• Bubble solution used in this product may stain or stick to some surfaces.
• Water toys sometimes get messy.
Protect play surfaces before use.
• To avoid bubble solution leaking from this toy, do not over-fill the bubble chamber.
Assembly
Lower Handle
11
• Insert and "snap" the lower handle into the socket in Mater, as shown.
Handlebar
2
• Fit the handlebar into the socket on one side of the lower handle.
• Push to "snap" the handlebar in place.
Using the Bubble Dispenser
IMPORTANT! Before use, remove the cap and seal from the bubble dispenser and throw it away.
Engine Cover
Cap
Bubble
Dispenser
11
• Slide the engine cover to access the bubble dispenser.
• Locate the cap in the engine.
• Attach the cap to the top of the bubble dispenser. Twist the dispenser to secure it to the cap.
• Turn the bubble dispenser over so that the cap is down and insert it back into the engine.
• Replace the engine cover over the bubble dispenser and press down for about 15 seconds to fill the bubble chamber inside Mater.
3
Bubblin
'
Fun
• Make sure all four wheels contact the ground when pushing this toy.
• Bubbles will begin to blow after about 15-20 walking steps and keep blowing as long as the toy is being pushed!
• When bubbles stop, press the bubble dispenser again for 15 seconds to refill the fun!
Note: We do not recommend the use of silicones or oily lubricants on this toy. As with any bubble producing toy, when even a very small amount of silicone or oily lubricants are put into or used near the bubble chambers, bubbles will not form.
©Disney/Pixar
Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, NY 14052 U.S.A. ©2011 Mattel, Inc.
All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc., unless otherwise indicated.
PRINTED IN MEXICO V7599pr-0920
4
Let
'
s Clean Up
11
• Slide the engine cover to the side and lift to remove the bubble dispenser from the engine.
• Turn the bubble dispenser upright and twist to remove the cap.
• Tip this toy forward to empty all the water.
Cap End Up
For Storage
Rinse Here Rinse Here
• Thoroughly rinse the bubble chamber on the side of this toy and the opening in the engine with clean water from a garden hose or faucet.
• Replace the cap on the bubble dispenser and place the it back into the engine, cap end up.
IMPORTANT! Do not remove or throw away the bubble dispenser that comes with this toy. Simply refill the bubble dispenser with bubble solution.
5
No bubbles
Problem
Problems and Solutions
Bubble solution is leaking
Bubble solution is foaming
Cause
Not enough bubble solution in bubble chamber
Bubble chamber is clogged and dirty
You have not walked far enough to produce bubbles
You are walking too quickly
The rear wheels do not contact the ground
Silicone or oily lubricants got into the bubble chamber
Bubble chamber over-filled
This toy is being pushed uphill
Bubble chamber is clogged
Solution
Press down on bubble dispenser for 15 seconds to refill.
Follow instructions in “Let’s
Clean Up” section to clean bubble chamber thoroughly.
This toy needs to be pushed a minimum of 15-20 walking steps before bubbles will begin to blow.
Walk at a slow, steady pace.
Push this toy so that the rear wheels always contact the ground.
Never use silicone or oily lubricants on this product (the wheels). Bubbles will not form if even a very small amount of these substances get into the bubble chamber.
Fill only by using the attached bubble dispenser.
Use only on flat, level ground.
Follow instructions in "Let's
Clean Up" section to clean bubble chamber thoroughly.
CONSUMER ASSISTANCE
1-800-432-5437 (US & Canada)
1300 135 312 (Australia)
Fisher-Price, Inc., 636 Girard Avenue, East Aurora, NY 14052.
Hearing-impaired consumers: 1-800-382-7470.
Outside the United States:
Canada: Mattel Canada Inc., 6155 Freemont Blvd.,
Mississauga, Ontario L5R 3W2; www.service.mattel.com.
Great Britain: Mattel UK Ltd, Vanwall Business Park,
Maidenhead SL6 4UB. Helpline: 01628 500303. www.service.mattel.com/uk
Mattel Europa, B.V., Gondel 1, 1186 MJ Amstelveen, Nederland.
Australia: Mattel Australia Pty. Ltd., 658 Church Street,
Locked Bag #870, Richmond, Victoria 3121 Australia.
New Zealand: 16-18 William Pickering Drive,
Albany 1331, Auckland.
6
advertisement
Related manuals
advertisement