Transcend MMCmicro Datasheet

TS128MMCM ~ TS512MMCM
128MB ~ 512MB MMCmicro
Description
Features
TS128MMCM ~ TS512MMCM is a 128MB ~ 512MB
• Storage Capacity: 128MB ~ 512MB
MMCmicro memory card. It’s a fastest, low-power,
• Support Dual Operating Voltage: 2.7~3.6V/1.65~1.95V
highly integration memory card. TS128MMCM ~
• Support clock frequencies: 0~52MHz
TS512MMCM is designed to provide an inexpensive,
• Support different Bus width: x1, x4
mechanically robust storage medium in card form for
• Operating Temperature: -25°C ~ 85°C
multimedia
• Storage Temperature:-40℃~ 85℃
consumer
applications
and
mobile
devices (handheld PCs, digital cameras, MP3
• Data access mode: Byte mode
players, etc.) to store, copy, and move data at
• Data Transfer Rate: up to 6MB/sec
high-speed transfer rate.
•
Fully
specification
Placement
compatible
with
MultiMediaCard
version 4.0 and backwards compatibility with
previous specification
• Form Factor: 12mm x 14mm x 1.1mm
• Endurance: 1,000,000 Program/Erase cycles
• MTBF: 1,000,000 hours
Front
Back
Pin Definition
MMC Mode
SPI Mode
Pin No.
1
2
3
4
5
6
7
8
9
10
Name
DAT2
DAT3
CMD
VSS1
VDD1
VDD2
CLK
VSS2
DAT0
Type
I/O/PP
I/O/PP
I/O/PP/OD
S
S
S
I
S
I/O/PP
Description
Data
Data
Command/Response
Ground
Power supply
Power supply
Clock
Ground
Data
DAT1
I/O/PP
Data
Name
Type
Description
I
I/PP
S
S
S
I
S
O/PP
Chip select
Data in
Ground
Power supply
Power supply
Clock
Ground
Data out
Not used
CS
DI
VSS1
VDD1
VDD2
SCLK
VSS2
DO
Not used
S: Power Supply; I:Input; O:Output; PP:Push-Pull; OD:Open-Drain; NC:Not Connected
Transcend Information Inc.
1
system
TS128MMCM
MMCM ~ TS512MMCM
TS512MMCM
128MB ~ 512MB MMCmicro
MultiMediaCard Architecture
VSS
CMD
VDD
CLK
Card Interface
Controller
Memory Core Interface
Memory Core
Transcend Information Inc.
2
DAT
Power On Detection
DAT
TS128MMCM ~ TS512MMCM
128MB ~ 512MB MMCmicro
Temperature Characteristics
Parameter
Min.
Max.
Unit
Operating temperature
-25
85
℃
Storage temperature
-40
85
℃
95
℃
Junction temperature
Electrical Characteristics
• Absolute Maximum Ratings
Parameter
Symbol
Rating
Unit
Power Supply Voltage
VCC
-0.6~+4.6
V
Input Voltage
VIN
-0.6~+4.6
V
Input/Output Voltage
VI/O
-0.6~+4.6
V
• Recommended Operation Conditions
Parameter
Symbol
Min.
Typ.
Max.
Unit
Power Supply Voltage (High Voltage Range)
VDDH
2.7
3.3
3.6
V
Power Supply Voltage (Low Voltage Range)
VDDL
1.65
1.8
1.95
V
Transcend Information Inc.
3
TS128MMCM ~ TS512MMCM
128MB ~ 512MB MMCmicro
DC Characteristics
• High Voltage Power Supply
(Ta=-25℃ to 85℃,VDDH=2.7V to3.6V)
Parameter
Symbol
Min.
Typ.
Max.
Unit
Condition
0.3
V
IOL =2mA
V
IOH =-100uA
0.125* VDDH
V
IOL =100uA
Output Low Voltage (OD)
VODOL
Output High Voltage (PP)
VOH
Output Low Voltage (PP)
VOL
Input High Voltage
VIH
0.625* VDDH
VDDH +0.3
V
Input Low Voltage
VIL
-0.3
0.25* VDDH
V
Operating Current
ICC
20(TBD)
mA
Stand-by Current
ISB
400(TBD)
uA
Input Leakage Current
ILI
-10/+10
uA
VIN =0 to VDDH
Output Leakage Current
ILO
-10/+10
uA
VOUT =0 to VDDH
Pin Capacitance
CP
7
pF
Power Output Voltage
VF
1.95
V
0.75* VDDH
1.50
1.8
IVCCF =0mA
IF＜＝240mA
• Low Voltage Power Supply
(Ta=-25℃ to 85℃,VDDL=1.65V to 1.95V)
Parameter
Symbol
Min.
Output High Voltage
VOH
VDDL -0.2
Output Low Voltage
VOL
Input High Voltage
VIH
Input Low Voltage
VIL
Operating Current
Typ.
Unit
Condition
V
IOH =-100uA
0.2
V
IOL =100uA
0.7* VDDL
VDDL +0.3
V
-0.3
0.3* VDDL
V
ICC
20(TBD)
mA
Stand-by Current
ISB
400(TBD)
uA
Input Leakage Current
ILI
-10/+10
uA
VIN =0 to VDDL
Output Leakage Current
ILO
-10/+10
uA
VOUT =0 to VDDL
Pin Capacitance
CP
7
pF
Transcend Information Inc.
4
Max.
IVCCF =0mA
TS128MMCM ~ TS512MMCM
128MB ~ 512MB MMCmicro
AC Characteristics
• High Speed Card Interface Timing
(Ta=-25℃ to 85℃,VDDH=2.7V to3.6V)
Parameter
Symbol
Min.
Max.
Unit
Clock Frequency (Data Transfer Mode)
fpp
26
52
MHz
Clock Frequency (Identification Mode)
fOD
0
400
KHz
Clock Low Time
tWL
6.5
Clock Rise Time
tTLH
3
ns
Clock Fall Time
tTHL
3
ns
Input Set-up Time
tISU
3
ns
Input Hold Time
tIH
3
ns
Output Delay Time
tDLY
5
Signal Rise Time
Signal Fall Time
Transcend Information Inc.
Notes
ns
14
ns
CL＜＝30pF
trise
3
ns
CL＜＝30pF
tfall
3
ns
CL＜＝30pF
5
TS128MMCM ~ TS512MMCM
128MB ~ 512MB MMCmicro
• Backwards Compatible Card Interface Timing
(Ta=-25℃ to 85℃,VDDH=2.7V to3.6V)
Parameter
Symbol
Min.
Max.
Unit
Clock Frequency (Data Transfer Mode)
fpp
0
20
MHz
Clock Frequency (Identification Mode)
fOD
0
400
KHz
Clock Low Time
tWL
10
Clock Rise Time
tTLH
10
ns
Clock Fall Time
tTHL
10
ns
Input Set-up Time
tISU
3
ns
Input Hold Time
tIH
3
ns
tDLY
9.7
Output Delay Time
• Command Latch Cycle
Transcend Information Inc.
6
Notes
ns
35
ns
CL＜＝30pF
TS128MMCM ~ TS512MMCM
Parameter
128MB ~ 512MB MMCmicro
Symbol Min.
30
tCLS1
CLE Setup Time
Unit
Notes
ns
CL<=80pF
CLE Hold Time
tCLH1
15
ns
CL<=80pF
CE Setup Time
tCS1
40
ns
CL<=80pF
CE Hold Time
tCH1
90
ns
CL<=80pF
ALE Setup Time
tALS1
90
ns
CL<=80pF
ALE Hold Time
tALH1
75
ns
CL<=80pF
WE Pulse Width
tWP1
45
ns
CL<=80pF
Data Setup Time
tDS1
90
ns
CL<=80pF
Data Hold Time
tDH1
30
ns
CL<=80pF
• Address Latch Cycle
Transcend Information Inc.
7
TS128MMCM ~ TS512MMCM
Parameter
Symbol
128MB ~ 512MB MMCmicro
CLE Setup Time
tCLS2
Min.
90
CE Setup Time
tCS2
195
ns
CL<=80pF
ALE Setup Time
tALS2
30
ns
CL<=80pF
ALE Hold Time
tALH2
15
ns
CL<=80pF
Write Cycle Time
tWC2
150
ns
CL<=80pF
WE Pulse Width
tWP2
45
ns
CL<=80pF
WE High Hold Time
tWH2
105
ns
CL<=80pF
Data Setup Time
tDS2
90
ns
CL<=80pF
Data Hold Time
tDH2
30
ns
CL<=80pF
• Input Data Latch Cycle
Transcend Information Inc.
8
Unit
Remark
ns
CL<=80pF
TS128MMCM ~ TS512MMCM
Parameter
CLE Hold Time
tCLH3
Min.
285
CE Hold Time
tCH3
195
ns
CL<=80pF
ALE Setup Time
tALS3
90
ns
CL<=80pF
Write Cycle Time
tWC3
60
ns
CL<=80pF
WE Pulse Width
tWP3
45
ns
CL<=80pF
WE High Hold Time
tWH3
15
ns
CL<=80pF
Data Setup Time
tDS3
30
ns
CL<=80pF
Data Hold Time
tDH3
30
ns
CL<=80pF
Transcend Information Inc.
Symbol
128MB ~ 512MB MMCmicro
9
Unit
Remark
ns
CL<=80pF
TS128MMCM ~ TS512MMCM
128MB ~ 512MB MMCmicro
• Serial Access Cycle after Read
Parameter
CE Access Time
tCEA4
Min.
285
Read Cycle Time
tRC4
60
ns
CL<=80pF
RE Pulse Width
tRP4
45
ns
CL<=80pF
RE High Hold Time
tREH4
15
ns
CL<=80pF
Data Setup Time
tDS4
5(TBD)
ns
CL<=80pF
Data Hold Time
tDH4
5(TBD)
ns
CL<=80pF
Ready to RE Low
tRR4
285
ns
CL<=80pF
Transcend Information Inc.
Symbol
10
Unit
Remark
ns
CL<=80pF
TS128MMCM ~ TS512MMCM
128MB ~ 512MB MMCmicro
Reliability and Durability
Temperature
Operation: -25°C / 85°C
Storage: -40°C (168h) / 85°C (500h)
Junction temperature: max. 95°C
Moisture and corrosion
Operation: 25°C / 95% rel. humidity
Stress: 40°C / 93% rel. hum./500h
Salt Water Spray: 3% NaCl/35C; 24h acc. MIL STD Method 1009
ESD protection
Contact Pads:
+/-4kV, Human body model according to ANSI EOS/ESD-S5.1-1998
Non Contact Pads area:
+/-8kV(coupling plane discharge)
+/-15kV(air discharge)
Human body model according to IEC61000-4-2
Durability
2,000 mating cycles; test procedure: t.b.d.
Bending
10N
Torque
0.06N.m
Drop test
1.5m free fall
UV light exposure
UV: 200nm, 15Ws/cm² according to ISO 7816-1
Visual inspection
Shape and form
No warp page; no mold skin; complete form; no cavities surface smoothness sigma
-0.1 mm/cm² within contour; no cracks; no pollution (fat, oil dust, etc.)
Above technical information is based on MMC4.0 standard specification and tested to be reliable. However, Transcend
makes no warranty, either expressed or implied, as to its accuracy and assumes no liability in connection with the use of
this product. Transcend reserves the right to make changes in specifications at any time without prior notice.
Transcend Information Inc.
11
">