HORIZON KRONOS C3, C3+ GNSS Receiver User Guide
إعلان
إعلان
KRONOS C3 Receiver
User Guide
Copyright
Copyright 2015-2016 HORIZON | Survey
Instruments Services Pte Ltd. All rights reserved.
The KRONOS are trademark of Survey Instruments
Services Pte Ltd. All other trademarks are the property of their respective owners.
Trademarks
All product and brand names mentioned in this publication are trademarks of their respective holders.
Safety Warnings
The Global Positioning System (GPS) is operated by the U.S. Government, which is solely responsible for the accuracy and maintenance of the GPS network. Accuracy can also be affected by poor satellite geometry and obstructions, like buildings and heavy canopy.
FCC interference statement
This equipment has been designed to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules in the Portable Mode.
These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation.
C3 GNSS Receiver User Guide – Revision 1.0 August 2016
CONTENTS
2. Getting started
1. I
NTRODUCTION
The C3 GNSS Receiver User Guide describes how to set up and use the
KRONOS® C3 GNSS receiver.
In this manual, “the receiver” refers to the C3 GNSS receiver unless otherwise stated.
Even if you have used other Global Navigation Satellite Systems (GNSS) products before, HORIZON recommends that you spend some time reading this manual to learn about the special features of this product. If you are not familiar with GNSS, go to www.horizon.sg
for an interactive look at Horizon and GNSS.
1.1. S
AFETY INFORMATION
1.1.1. W
ARNINGS AND CAUTIONS
An absence of specific alerts does not mean that there are no safety risks involved.
A Warning or Caution information is intended to minimize the risk of personal injury and/or damage to the equipment.
WARNING - A Warning alerts you to a potential misused or wrong setting of the equipment.
CAUTION - A Caution alerts you to a possible risk of serious injury to your person and/or damage to the equipment.
1.1.2. R
EGULATIONS AND SAFETY
The receivers contain a built-in wireless modem for signal communication through Bluetooth® wireless technology or through external communication datalink. Regulations regarding the use of the wireless modem vary greatly from country to country. In some countries, the unit can be used without obtaining an end-user license. However, in some countries, the administrative permissions are required. For license information, consult your local dealer. Bluetooth® operates in license-free bands.
Before operating a C3 GNSS receiver, determine if authorization or a license to operate the unit is required in your country. It is the responsibility of the end-user to obtain an operator's permit or license for the receiver for the location or country of use.
C3 GNSS Receiver User Guide Page
4
1. Introduction
1.1.3. U
SE AND
C
ARE
This receiver is designed to withstand the rough environment that typically occurs in the field. However, the receiver is high-precision electronic equipment and should be treated with reasonable care.
CAUTION - Operating or storing the receiver outside the specified temperature range will cause irreversible damage.
1.2. T
ECHNICAL SUPPORT
If you have a problem and cannot find the information you need in this manual or HORIZON website (www.horizon.sg), contact your local HORIZON dealer from which you purchased the receiver(s).
1.3. D
ISCLAIMER
Before using the receiver, please make sure that you have read and understood this User Guide, as well as the safety information. HORIZON holds no responsibility for the wrong operation by users and for the losses incurred by the wrong understanding about this User Guide. However,
HORIZON reserves the rights to update and optimize the contents in this guide regularly. Please contact your local dealer for new information.
1.4. Y
OUR COMMENTS
Your feedback about this user guide will help us to improve it in future revision. Please email your comments to [email protected]
.
C3 GNSS Receiver User Guide Page 5
2. Getting started
2. G
ETTING STARTED WITH
C
3
2.1. A
BOUT THE RECEIVER
The C3 GNSS receiver incorporates a GNSS engine, GNSS antenna, internal radio, optional 4G cellular modem(only for C3+), Bluetooth, Wi-Fi, and dual-battery in a ruggedized and miniature unit that is easy for you to set up an all-in-one RTK rover or mobile base station.
The receiver can be used as the part of a RTK GNSS system with HORIZON
K-COM software. And you can download the GNSS data that recorded in the internal memory of receiver to a computer.
To configure the receiver for performing a wide variety of functions, you can use the web interface by connecting the receiver with PC or smart phone through Wi-Fi.
2.2. P
ARTS OF THE RECEIVER
Battery compartment is on the backside. Serial ports and connectors are located on the bottom of the unit.
2.2.1. F
RONT PANEL
The following figure shows a front view of the receiver.
The front panel contains five indicator LEDs, and two buttons.
C3 GNSS Receiver User Guide Page
6
2. Getting started
Power LED
Satellite LED
Correction LED
Wifi LED Record LED
Switch Button
Power & Enter button
Name
Power LED
Satellite LED
Correction LED
Wifi LED
Record LED
Static Button
Description
Shows the C3 GNSS is on or off
Shows the number of satellites that the receiver has tracked.
When the receiver is searching satellites, the blue
LED flashes once every 5 seconds.
When the receiver has tracked N satellites, the blue
LED will flash N times every 5 seconds.
Indicates whether the receiver is transmitting/receiving differential data.
The green LED flashes once per second when
As a Base station: successfully transmitting differential data.
As a Rover station: successfully receiving differential data from Base station.
Shows the Wifi of C3 GNSS is on or off
The record LED only flashes under 2 situations
A. In the static mode
The interval of flashing shows the sample interval of collecting data.
B.RTK mode
When the receiver is connecting to Controller and
Receiving commands or just communicating with
Controller.
The function of switch button is to switch C3 GNSS from RTK mode to static mode. The procedure can be divided into 2 steps.
Step 1: Switching
Long press the button until the Record LED off.
Step 2: Checking
Press the switch button, if the correction LED turns
C3 GNSS Receiver User Guide Page 7
2. Getting started
Power Button on, it means the switching succeed.
To Turn on C3 GNSS, long press the button until the power LED lights up.
2.2.2. L
OWER HOUSING
The lower housing contains one SIM card slot, one battery compartments, one TNC radio antenna connector, two communication and power ports.
TNC radio antenna connector
SIM card slot (only for C3+ )
IO serial communication and power in port
USB communication and power in port
Battery compartment
Port Name
IO port
USB port
Radio antenna connector
Description
This port is a 7-pin Lemo connector that supports RS-232 communications and external power input.
Users can use GPS to PC Data Cable supplied with the system to realize RS-232 communications between the receiver and computer or controller. Also, users can use a
7-pin cable to transmit differential data to an external radio.
This port is a 7-pin Lemo connector that supports USB communications and external power input.
Users can USB Cable supplied with the system to download the logged data to a computer.
The OTG Cable supplied with the system can be used to upgrade the receiver firmware by connecting the receiver to a USB flash disk, or directly log the static data to a USB flash disk.
Connect a radio antenna to internal radio of the receiver. And this connector is not used if you are using an external radio.
C3 GNSS Receiver User Guide Page 8
2. Getting started
2.3. B
ATTERIES AND POWER
2.3.1. I
NTERNAL BATTERIES
The receiver has two rechargeable Lithium-ion batteries, which can be removed for charging.
2.3.1.1. Charging the battery
The rechargeable Lithium-ion battery is supplied partially charged. Charge the battery completely before using it for the first time. To charge the battery, first remove the battery from the receiver, and then place it in the battery charger, which is connected to AC power.
WARNING - Charge and use the rechargeable Lithium-ion battery only in strict accordance with the instructions. Charging or using the battery in unauthorized equipment can cause an explosion or fire, and can result in personal injury and/or equipment damage.
To prevent injury or damage:
• Do not charge or use the battery if it appears to be damaged or leaking.
• Charge the Lithium-ion battery only in a Horizon product that is specified to charge it. Be sure to follow all instructions that are provided with the battery charger.
• Discontinue charging a battery that gives off extreme heat or a burning odor.
• Use the battery only in Horizon equipment that is specified to use it.
• Use the battery only for its intended use and according to the instructions in the product documentation.
2.3.1.2. Battery safe
WARNING - Do not damage the rechargeable Lithium-ion battery. A damaged battery can cause an explosion or fire, and can result in personal injury and/or property damage.
To prevent injury or damage:
• Do not use or charge the battery if it appears to be damaged. Signs of damage include, but are not limited to, discoloration, warping, and leaking battery fluid.
• Do not expose the battery to fire, high temperature, or direct sunlight.
• Do not immerse the battery in water.
• Do not use or store the battery inside a vehicle under hot weather condition.
C3 GNSS Receiver User Guide Page 9
• Do not drop or puncture the battery.
• Do not open the battery or short-circuit its contacts.
2. Getting started
WARNING - Avoid contact with the rechargeable Lithium-ion battery if it appears to be leaking. Battery fluid is corrosive, and contact with it can result in personal injury and/or property damage.
To prevent injury or damage:
• If the battery leaks, avoid with the battery fluid.
• If battery fluid gets into your eyes, immediately rinses your eyes with clean water and seek medical attention. Please do not rub your eyes!
• If battery fluid gets onto your skin or clothing, immediately use clean water to wash off the battery fluid.
2.3.2. E
XTERNAL POWER SUPPLY
Two methods are available for providing the external power to the receiver by the GPS to PC Data Cable/USB Cable+ Power Adapter, or GPS to PC Data
Cable/USB Cable + external power cable (option purchase)+ vehicle battery.
In the office:
The Power Adapter is connecting with AC power of 100-240V, the output port of the Power Adapter connects with the Power Port of the GPS to PC
Data Cable/USB Cable.
In the field:
The external power cable is connecting with a vehicle battery, the output port of the external power cable connects with the Power Port of the GPS to
PC Data Cable/USB Cable.
WARNING - Use caution when connecting external power cable's clip leads
C3 GNSS Receiver User Guide Page 10
2. Getting started to a vehicle battery. Do not allow any metal object to connect (short) the battery's positive (+) terminal to either the negative (-) terminal or the metal part of the vehicle battery. This could result in high current, arcing, and high temperatures, exposing the user to possible injury.
2.4. I
NSERTING BATTERY AND
SIM
CARD
To open the cover, push inward the spring-loaded button on both side of the battery cover .
To remove the battery, directly take it out.
Battery cover
SIM Card Slot
Insert the SIM card with the contacts facing downward, as indicated by the
SIM card icon next to the SIM card slot(For C3+).
To eject the SIM card, slightly pull it out.
Tip – The SIM card is provided by your cellular network service provider.
2.5. P
RODUCT BASIC SUPPLY ACCESSORIES
2.5.1. B
ASE KIT BASIC SUPPLY
Item
C3 GNSS Receiver
Picture
C3 GNSS Receiver User Guide Page 11
UHF Bar Antenna (450-470 MHz)
OTG Cable
USB Cable
GPS to PC Data Cable
Lithium Battery
H.I. Tape
Extension Pole
Tribrach with Optical Plummet
Auxiliary H.I. Tool
Tribrach Adaptor
Transport Hard Case
2. Getting started
C3 GNSS Receiver User Guide Page 12
2.5.2. R
OVER KIT BASIC SUPPLY
Item
C3 GNSS Receiver
Picture
UHF Bar Antenna (450-470 MHz)
OTG Cable
USB Cable
2. Getting started
GPS to PC Data Cable
Battery Charger
Power Adapter with Cord
Lithium Battery
2M Range Pole w/bag
Auxiliary H.I. Tool
Transport Hard Case
C3 GNSS Receiver User Guide Page 13
2. Getting started
2.6. C
ONNECTING TO AN OFFICE COMPUTER
The receiver can be connected to an office computer for serial data transfer or settings via a GPS to PC Data Cable. Before you connect to the office computer, ensure that the receiver is powered on by internal battery or external power.
The following figure shows how to connect to the computer for serial data transfer or settings:
GPS to PC Data Cable
2.7. C
ONNECTING TO A CONTROLLER
2.7.1. C
ONNECTING VIA
W
I
-F
I WITH
K-
COM
SOFTWARE
1. Turn on the controller → tap Start button → tap Settings → select
Connection tab → tap Wireless Manager → turn on the Wi-Fi function
→ tap Menu button → tap Wi-Fi Settings.
2. In the Configure Wireless Network Settings screen, tap the wireless network named as the SN of your receiver.
3. In the pop-up screen, tap Next button to enter Configure Network
Authentication screen → enter the Network Key →tap Next button.
C3 GNSS Receiver User Guide Page 14
2. Getting started
Tip – The Wi-Fi key of the receiver is 12345678 by default.
4. Tap Finish button in the pop-up screen, and then you can check that the controller system has connected to the Wi-Fi of the receiver.
5. Go back to the main screen → run K-COM → create a new project or open an existing project.
6. In the Main Menu, tap Device →tap Connection.
7. Select Horizon for the Manufacture field, Smart GNSS for Device Type field, WIFI for Connect field, Kronos C3 for Antenna Type field → select
C3 GNSS Receiver User Guide Page 15
2. Getting started
Base or Rover as Connection Type according to the your needs → tap
in the lower right corner to connect the software with the receiver via Wi-Fi.
2.7.2. C
ONNECTING VIA
B
LUETOOTH WITH
K-
COM
SOFTWARE
1. Turn on the controller →run K-COM → create a new project or open an existing project.
2. In the Main Menu, tap Device → tap Connection.
3. Select Horizon for the Manufacture field, Smart GNSS for Device Type field, Bluetooth for Connection field.
4. Tap icon next to Connection field → tap Search Device in the pup-up Bluetooth Binding screen → select the Bluetooth device named as the SN of your receiver → tap
C3 GNSS Receiver User Guide in the lower right corner to go
Page 16
2. Getting started back to Connection screen.
5. Select COM Port that you want to be used to connect the controller with the receiver for the Port field → Kronos C3 for Antenna Type field
→ select Base or Rover as Connection Type according to the your needs
→ tap in the lower right corner to connect the software with the receiver via Bluetooth.
2.8. C
ONNECTING TO A
USB
DRIVE
The receiver can log data directly to a USB drive using the supplied OTG cable. Also, users can use USB drive to upgrade the firmware for your receiver using the OTG cable.
The following figure shows how to connect to a USB drive:
OTG Cable
C3 GNSS Receiver User Guide Page 17
2. Getting started
2.8.1. F
OR DATA LOGGING
The receiver can log data directly to a USB drive; however, the logged
(existing) data cannot be downloaded directly from the receiver memory to a USB drive.
To log data directly to a USB drive:
1. Connect the USB device (or other external storage device, such as portable hard drive) with receiver through USB port using the OTG cable.
2. Configure the data logging settings through a web browser (see
for instruction).
Notes
Select a data logging session, and then select “External Storage” as the store location.
Make sure the data logging session selected is switched on after the configuration. Also, user need to verify the Log Status is “Recording” before leave the web browser.
3. The receiver will log static data to the USB drive.
Note – To download the data logged in the USB driver, connect the USB driver to the computer, find a folder named as “repo” in the USB drive, and then locate the logged static data according to procedure illustrated as follows:
C3 GNSS Receiver User Guide Page 18
2. Getting started
2.8.2. F
OR FIRMWARE UPGRADE
1. Copy the firmware file (xxx.bin file) to the root directory of external storage device such as USB drive, portable hard drive.
2. Connect the external storage device with receiver through USB port using the OTG cable.
3. Start up the receiver. All the five satellite lights will be blinking together.
4. Press Switch button to upgrade the firmware. The five satellite lights will be blinking by turns.
5. When the upgrading is completed, the receiver will be restarted.
6. Remove the OTG cable.
Note – You can also use Wi-Fi to upgrade the firmware for your receiver
using the web browser (see
6.11.3. Firmware update submenu
for instruction).
2.9. D
OWNLOADING LOGGED DATA
Data logging involves the collection of GNSS measurement data over a period of time at a static point or points, and subsequent post-processing of the information to accurately compute baseline information. Data logging using receivers requires access to suitable GNSS post-processing software such as the Kronos Processor Software.
The following figure shows how to connect to the computer for downloading logged data:
USB Cable
C3 GNSS Receiver User Guide Page 19
2. Getting started
The procedures of downloading logged data in the receiver are as follows:
1. Switch on the receiver and connect it with a computer by USB Cable.
After the successful connection, a removable disk named as the Serial
Number (SN) of the receiver will appear on the computer.
2. Double click the removable disk and you will see the folder named as
“repo”. Double click this folder, you will see 9 folders. The “push_log” folder is used to save the log files, and the other 8 folders represent different logging session and are used for store static data.
3. Double click the folder that you has configured to store the static data, you will see the folder(s) created by the C3 system automatically and named by the date which is decide by GPS time when you start to log data.
4. Select the destination folder and double click it, and then two folders named as different data format (hcn and rinex) will be displayed.
5. Select the data format that you has configured to save the static data, you will find the static raw data.
Tip – For hcn files, the name of the file is represented as XXXXXXDDDNN, where XXXXXX is the SN of the receiver, DDD is day of year, and NN is the recording session.
WARNING – The static data will be saved in the first logging session, the
“record_1” folder, by default. Old files will be deleted if the storage space is full. If you configure not to auto delete old files when the memory is low, the receiver will stop data logging.
C3 GNSS Receiver User Guide Page 20
3. Base station setup and operation
3. B
ASE STATION SETUP AND OPERATION
Real-Time Kinematic (RTK) operation provides centimeter-level precision by eliminating errors that are present in the GNSS system. For all RTK operations, you require both a rover receiver and a source of corrections from a base station or network of base stations.
A base station consists of a receiver that is placed at a known point. The receiver tracks the same satellites that are being tracked by the rover receiver simultaneously. Errors in the GNSS system are monitored at the base station, and a series of position corrections are computed. The messages are sent through a radio link to the rover receiver, where they are used to correct the real time positions of the rover.
This chapter provides the information to help you identify good setup locations, outlines basic precautions that you need to take to protect the equipment, and describes the conventional process to set up the base station and the configuring procedure that required for transmitting correction data.
3.1. B
ASE STATION SETUP GUIDELINES
For good performance, the following base station setup guidelines are recommended:
Place the GNSS receiver in a location on the worksite where equal range in all directions provides full coverage of the site.
Place the GNSS antenna in a location that has a clear line of sight to the sky in all directions. Do not place the antenna near vertical obstructions such as buildings, deep cuttings, site vehicles, towers, or tree canopy.
The GNSS antenna must have a dear line of sight to the sky at all times during operation.
Place the GNSS and radio antennas as high as practical. This minimizes multipath from the surrounding area, and enables the radio to broadcast to the maximum distance.
Choose the most appropriate radio antenna for the size of the worksite.
The higher the gain on the antenna, the longer the range.
Make sure that the GNSS receiver does not lose power. To operate continuously for more than a few hours without loss of power at the base station, provide external power. When you use an external power supply, the integrated battery provides a backup power supply, enabling you to maintain continuous operation through a mains power failure.
Do not locate a GNSS receiver, GNSS antenna, or radio antenna within
C3 GNSS Receiver User Guide Page
21
3. Base station setup and operation
400 meters (about 1,300 feet) of transmitters, such as a power radar or cellular communications tower.
Do not set up the base station close to the sources of electromagnetic interference, include alternators and generators, electric motors, equipment with DC-to-AC converters, etc.
Do not operate the receiver outside the specified operating temperature range -40°C to +60°C (-40°F to +140°F).
Take reasonable care to keep the GNSS receiver equipment dry, which could prolong their life and reduce the effects of corrosion on ports and connectors.
3.2. O
UTPUTTING CORRECTIONS USING INTERNAL RADIO
MODEM
3.2.1. B
ASE STATION SETUP
1. Connect the radio antenna ontoC3 receiver. Screw the receiver onto extension pole.
2. Screw the extension pole with auxiliary H.I. tool onto tribrach adaptor.
3. Mount the tribrach onto the tripod.
4. Insert the tribrach adaptor into the tribrach.
5. Level and plumb the receiver over the known (control) point.
6. Measure the height of the base station GNSS antenna by measuring the slant height from the known (control) point to the auxiliary H.I. tool.
Note – Select “Bottom” as the measurement method, select “Kronos C3” as antenna type, and then enter the vertical height from the known (control) point to the bottom of receiver that you calculated by adding the height of
the extension pole to the height from the known (control) point to the auxiliary H.I. tool, the Horizon K-COM will calculate the height to the Antenna
Phase Center (APC) automatically.
7. If required, connect the receiver to an external 12 V power supply.
C3 GNSS Receiver User Guide Page 22
3. Base station setup and operation
3.2.2. C
ONFIGURING THE BASE STATION
3.2.2.1. Configuring via K-COM software
1. Power on the receiver.
2. Turn on the controller → run K-COM → create a new project or open an existing project → establish the connection with receiver via Bluetooth or Wi-Fi (see
2.7. Connecting to a controller
for the operations).
3. After successful connection, tap Communication Mode in the Device screen.
4. In Communication Mode screen, select Radio for Mode field.
5. Configure the related parameters from the dropdown list: Protocol,
Freq, Baud and Power.
6. Tap to confirm and save the settings → tap right corner to back to Device screen.
7. Tap Base Config → select Start Base Station tab.
8. Configure the GNSS antenna related parameters as follows: in the lower
Type field: tap next to Type field to select Kronos C3 as antenna type.
Measure To field: select Bottom from the dropdown list.
Height field: enter the vertical height (in meters) you calculated from the known (control) point to the bottom of receiver for
Height field.
9. Configure the coordinates of base station.
C3 GNSS Receiver User Guide Page 23
3. Base station setup and operation
There are three methods available to configure the base station coordinates: a) Tap next to Name field to select an existing point.
b) Manually enter the coordinates of the known point in B, L and H.
c) Tap Get Current Position button to obtain the current position of the base receiver.
10. Go to Base Parameters tab → select Inner Radio for Transmit COM field
→ configure the Data Format field, Baud Rate field and Elevation Mask field according to your need.
11. Tap in the lower right corner to save the settings, and then the
K-COM will disconnect with the receiver automatically.
3.3. O
UTPUTTING CORRECTIONS USING EXTERNAL RADIO
3.3.1. B
ASE STATION SETUP
For base receiver part:
1. Screw the C3 receiver onto extension pole.
2. Screw the extension pole with auxiliary H.I. tool onto tribrach adaptor.
3. Mount the tribrach onto the tripod.
4. Insert the tribrach adaptor into the tribrach.
5. Level and plumb the receiver over the known (control) point.
6. Measure the height of the base station GNSS antenna by measuring the slant height from the known (control) point to the auxiliary H.I. tool.
Note – Select “Bottom” as the measurement method, select “Kronos C3” as antenna type, and then enter the vertical height from the known (control) point to the bottom of receiver that you calculated by adding the height of the extension pole to the height from the known (control) point to the auxiliary H.I. tool, the Horizon K-COM will calculate the height to the
Antenna Phase Center (APC) automatically.
7. If required, connect the receiver to an external 12 V power supply.
For external radio part (take the Horizon HR35 Datalink for example):
8. Connect the Datalink Antenna to the 3 meter Cable for Datalink
Antenna.
9. Connect 3 meter Cable for Datalink Antenna to Datalink Antenna
Mounting Pole.
10. Screw the Datalink Antenna Mounting Pole onto the tribrach adapter.
11. Mount the tribrach onto the tripod.
C3 GNSS Receiver User Guide Page 24
3. Base station setup and operation
12. Insert the tribrach adaptor into the tribrach.
13. Set up the Datalink Antenna nearby the base receiver.
14. Fix the HR35 Datalink onto the tripod.
15. Place the car battery at an appropriate location.
For connection between the receiver part and external radio part:
16. Connect Datalink Antenna to the Datalink Antenna Slot of HR35
Datalink via 3 meter Cable for Datalink Antenna.
17. Connect the base receiver with HR35 Datalink via GPS to Datalink Cable.
18. Connect the car battery with HR35 Datalink via Datalink External Power
Cable.
CAUTION – The Datalink Antenna must be connected to the Datalink before the Datalink is powered on; otherwise, the Datalink can be damaged.
3.3.2. C
ONFIGURING THE BASE STATION
3.3.2.1. Configuring via K-COM software
1. Power on the receiver.
2. Turn on the controller → run K-COM → create a new project or open an existing project → establish the connection with receiver via Bluetooth or Wi-Fi (see
2.7. Connecting to a controller
for the operations).
3. After successful connection, tap Communication Mode in the Device
C3 GNSS Receiver User Guide Page 25
3. Base station setup and operation screen.
4. In Communication Mode screen, select External Radio for Mode → tap in the lower right corner to back to Device screen.
5. Tap Base Config → select Start Base Station tab.
6. Configure the GNSS antenna related parameters as follows:
Type field: tap next to Type field to select Kronos C3 as antenna type.
Measure To field: select Bottom from the dropdown list.
Height field: enter the vertical height (in meters) you calculated from the known (control) point to the bottom of receiver for
Height field.
7. Configure the coordinates of base station.
There are three methods available to configure the base station coordinates: a) Tap next to Name field to select an existing point.
b) Manually enter the coordinates of the known point in B, L and H.
c) Tap Get Current Position button to obtain the current position of the base station.
8. Go to Base Parameters tab → select Outer Radio for Transmit COM field
→ configure the Data Format field, Baud Rate field and Elevation Mask field according to your need.
9. Tap in the lower right corner to save the settings, and then the
K-COM will disconnect with the receiver automatically.
10. After the receiver is successfully transmitting correction data (with the
Correction Green LED flashing once per second), power on the external radio, and then configure the external radio from its panel.
C3 GNSS Receiver User Guide Page 26
2. Rover station setup and operation
4. R
OVER STATION SETUP AND OPERATION
Real-Time Kinematic (RTK) operation provides centimeter-level precision by eliminating errors that are present in the GNSS system. For all RTK operations, you require both a rover receiver and a source of corrections from a base station or network of base stations.
The second part of the RTK GNSS system is the rover receiver. The rover receiver is moved between the points that require measurement or stakeout.
The rover receiver is connected to a base station or to a source of RTK corrections such as a CORS (Continuous Operational Reference System) . The connection is provided by:
an integrated radio
an integrated cellular modem
a cellular modem in the controller
This chapter provides the information to help you identify good setup locations, describes the conventional process to set up the rover station and the configuring procedure that required for receiving correction data.
4.1. R
OVER STATION SETUP GUIDELINES
For good rover operation, observe the following setup guidelines:
Place the GNSS antenna in a location that has a clear line of sight to the sky in all directions. Do not place the antenna near vertical obstructions such as buildings, deep cuttings, site vehicles, towers, or tree canopy.
GNSS rovers and the base station receive the same satellite signals from the same satellites. The system needs five common satellites to provide RTK positioning.
WARNING – Take care not to touch overhead power lines with the Kronos C3
GNSS receiver or the range pole when moving the equipment into position.
Touching overhead power lines may cause electrocution, leading to serious injury.
GNSS satellites are constantly moving. Because you cannot measure at a specific location now does not mean that you will not be able to measure there later, when satellite coverage at the location improves.
To get a fixed position solution with centimeter precision, initialize the
RTK rover receiver. For initialization to take place, the receiver must track at least five satellites that the base station is also tracking. In a dual-satellite constellation operation, for example, GPS and GLONASS,
C3 GNSS Receiver User Guide Page
27
4. Rover station setup and operation the receiver must track at least six satellites.
To continue to survey at centimeter precision, the rover must continuously track at least four satellites that the base station is also tracking. The radio link between the base and rover receivers must also be maintained.
Loss of the satellite signals will result in a loss of centimeter position precision.
4.2. R
OVER STATION SETUP
1. If required, connect the radio antenna onto C3 receiver.
2. Screw the receiver on top of the range pole.
3. Fix the controller bracket on the range pole.
4. Fit the controller in the controller bracket.
5. Level and plumb the receiver over the target measuring point.
4.3. C
ONFIGURING THE ROVER STATION VIA
K
-
COM
SOFTWARE
4.3.1. R
ECEIVING CORRECTIONS USING INTERNAL RADIO MODEM
1. Power on the receiver.
2. Turn on the controller → run K-COM → create a new project or open an existing project → establish the connection with receiver via Bluetooth or Wi-Fi (see
2.7. Connecting to a controller
for the operations).
3. After successful connection, tap Rover Config in the Device screen.
4. In Rover Config screen, configure the related parameters from the dropdown list or enter the value with the soft keyboard: Data Format,
Elevation Mask, PDOP Limit, Safe Mode and Iono Condition.
Note – Select the Data Format the same as that of base receiver.
5. Configure the antenna parameters as follows:
Type field: tap next to Type field to select Kronos C3 as antenna type.
Measure To field: select Bottom from the drop-down list.
Height field: enter the height (in meters) of the range pole you are using.
6. If required, tick Warning when base changed option → tap in the lower right corner to save the settings and go back to Device screen.
C3 GNSS Receiver User Guide Page 28
4. Rover station setup and operation
7. Tap Communication Mode → select Radio for Mode field.
8. Configure the radio parameters as follows:
Protocol field: select the protocol the same as that of base station.
Freq field: select the frequency the same as that of base station.
Tip – Users can select a radio channel from the dropdown list. The frequency of channel 1 to 9 is predefined; however, the frequency of channel 0 is editable.
Baud field: select the baud rate the same as that of base station.
Power field: select the power from the dropdown list according to your need.
9. Tap to confirm and save the settings of the radio.
C3 GNSS Receiver User Guide Page 29
4. Rover station setup and operation
10. After the radio parameters are successfully configured, tap in the lower right corner to back to Device screen.
11. Users can conduct surveying work after the rover receiver receives correction data (with correction LED flashes once per second) and gets fixed solution.
4.3.2. R
ECEIVING CORRECTIONS USING INTERNAL CELLULAR MODEM
(O
NLY
APPLY TO
C3+)
1. Insert a SIM card into SIM card slot of the receiver (please see
Inserting battery and SIM card
for instruction) and the power on the receiver.
2. Turn on the controller → run K-COM→ create a new project or open an existing project → establish the connection with receiver via Bluetooth or Wi-Fi (see
for the operations).
3. After successful connection, tap Rover Config in the Device screen.
4. In Rover Config screen, configure the related parameters from the dropdown list or enter the value with the soft keyboard: Data Format,
Elevation Mask, PDOP Limit, Safe Mode and Iono Condition.
Note – Select the Data Format the same as that of base receiver.
5. Configure the antenna parameters as follows:
Type field: tap next to Type field to select Kronos C3 as antenna type.
Measure To field: select Bottom from the dropdown list.
Height field: enter the height (in meters) of the range pole you are using.
C3 GNSS Receiver User Guide Page 30
4. Rover station setup and operation
6. If required, tick Warning when base changed option → tap in the lower right corner to save the settings and go back to Device screen.
7. Tap Communication Mode → select Network for Mode field.
8. Configure the network parameters as follows:
Protocol field: select the protocol according to your need.
IP Addr field: enter the IP address and the Port with the soft keyboard, or tap service.
Source field: tap next to this field to select the predefined next to this field to get the source table list, and then tap to select the suitable source table.
User Name field: enter the user name of the network (such as NTRIP network), if required.
Password field: enter the user name of the network (such as NTRIP network), if required.
9. Tap to confirm and save the settings.
C3 GNSS Receiver User Guide Page 31
4. Rover station setup and operation
10. After the service is successfully logged on, tap in the lower right corner to back to Device screen.
11. Users can conduct surveying work after the rover receiver receives correction data (with correction LED flashes once per second) and gets fixed solution.
Note – Before switch to other communication mode, please tap
Communication Mode screen to break the connection to the network.
4.3.3. R
ECEIVING CORRECTIONS USING CELLULAR MODEM IN THE
CONTROLLER
(O
NLY APPLY TO
C3+)
in
1. Power on the receiver.
2. Insert a SIM card into SIM card slot of your controller, and then turn on the controller to establish network connection (please refer to corresponding user guide of the controller that you are using for
C3 GNSS Receiver User Guide Page 32
4. Rover station setup and operation instruction).
3. Run K-COM on the controller → create a new project or open an existing project → establish the connection with receiver via Bluetooth or Wi-Fi
(see
2.7. Connecting to a controller
for the operations).
4. After successful connection, tap Rover Config in the Device screen.
5. In Rover Config screen, configure the related parameters from the dropdown list or enter the value with the soft keyboard: Data Format,
Elevation Mask, PDOP Limit, Safe Mode and Iono Condition.
Note – Select the Data Format the same as that of base receiver.
6. Configure the antenna parameters as follows:
Type field: tap next to Type field to select Kronos C3 as antenna type.
Measure To field: select Bottom from the dropdown list.
Height field: enter the height (in meters) of the range pole you are using.
7. If required, tick Warning when base changed option → tap in the lower right corner to save the settings and go back to Device screen.
8. Tap Communication Mode → select PDA Network for Mode field.
9. Configure the network parameters as follows:
Protocol field: select the protocol according to your need.
IP Addr field: enter the IP address and the Port with the soft keyboard, or tap service.
next to this field to select the predefined
C3 GNSS Receiver User Guide Page 33
4. Rover station setup and operation
Source field: tap next to this field to get the source table list, and then tap to select the suitable source table.
User Name field: enter the user name of the network (such as NTRIP network), if required.
Password field: enter the user name of the network (such as NTRIP network), if required.
10. Tap to log-in the network service.
11. After the successful login, tap in the lower right corner to back to
Device screen.
12. Users can conduct surveying work after the rover receiver receives correction data (with correction LED flashes once per second) and gets fixed solution.
C3 GNSS Receiver User Guide Page 34
4. Rover station setup and operation
Note – Before switch to other communication mode, please tap
Communication Mode screen to break the connection to the network.
in
C3 GNSS Receiver User Guide Page 35
6. Survey with K-COM software
5. S
URVEY WITH K
-
COM SOFTWARE
The Horizon K-COM Software is a field survey software which developed based on more than ten years of development experience of Horizon and feedback of surveyors from different fields of application. K-COM provides with a complete set of features for any survey projects, including data collection, stakeout, COGO (Coordinate Geometry) function, and more, which makes this software an ideal option for everyday field work.
This chapter briefly introduces the basic survey workflows of K-COM, combining with C3 GNSS receiver.
5.1. N
EW PROJECT
Turn on the controller, run K-COM software and establish the connection with receiver via Bluetooth or Wi-Fi (see
2.7. Connecting to a controller
for the operations), and then create a new project or open an existing project before measuring any points, or making any calculations.
To create a new project:
1. Tap button on the lower left corner of the initial interface that the
K-COM starts with.
2. Enter the Project name and Create by (operator), select Time zone from the dropdown list, and then tap button.
C3 GNSS Receiver User Guide Page
36
5. Survey with K-COM software
Note – Also, users can configure other parameters, such as Create By
(operator) and time zone, according to your need.
3. Select one coordinate system from the template list, or tap default
(from template) if there is no suitable template, and then tap
button.
4. Confirm the ellipsoid information or select one ellipsoid from the dropdown list for Name field, and then tap button.
C3 GNSS Receiver User Guide Page 37
5. Survey with K-COM software
5. In DatumWidget screen, select one Model from the dropdown list.
There are three model options available: a)
NONE: No transformation parameters are needed to be entered.
b)
Bursa 7 Parameter: Users need to enter seven parameters for
local transformation, including translation, rotation and scale.
c)
Molodensky 3 Parameter: Users need to enter three translation
parameters for local transformation.
Note – To configure the parameters for Bursa 7 Parameter option and
Molodensky 3 Parameter option, users need to tap editing function.
button to unlock the
Tip – The default login values of editing function are “admin” for Name and
C3 GNSS Receiver User Guide Page 38
5. Survey with K-COM software
“123456” for Password.
6. Select one projection from the dropdown list, configure the projection related parameters, and then tap button to save the new project.
7. The project name appears in the title area of the main menu.
5.2. K
EY IN POINTS
1. In the main menu, tap Data → tap Point Management.
2. Tap button in the lower left corner of Point Data Management screen, and then configure the related parameters of the new point as follows:
Name field: enter the point name.
C3 GNSS Receiver User Guide Page 39
5. Survey with K-COM software
Code field: enter the code of the point, if required.
CRS field: select the coordination system from the dropdown list. The available options are: Local and WGS84.
Role field: select the role of the point from the dropdown list. The available options are: Null, To Stake Out and Control.
X, Y, H field: enter the local grid coordinate of the point.
3. Tap the point.
button in the lower right corner of New point screen to save
5.3. M
EASURE POINTS
Note – To ensure the accuracy of the coordinates measured, please perform measurements after the rover receiver receives correction data (with correction LED flashes once per second) and gets fixed solution.
5.3.1. M
EASURE POINTS IN CONVENTIONAL MODE
1.
In the main menu, tap Survey → tap Point Survey.
2.
Enter the point name in the input frame on the top left corner.
Notes
The system will automatically increment the numeric component of the measured point name.
The measured points will be automatically incremented from “P1”, by default.
3.
If necessary, enter the feature code in the input frame on the top right corner.
4.
Tap window.
button to select a measurement mode in the pop-up
Notes
Users can tap button to configure the settings of each
C3 GNSS Receiver User Guide Page 40
5. Survey with K-COM software
measurement method in the pop-up Survey Option screen.
The auto measure function is available for three measurement modes: Topo Mode, Rapid Mode and Compensated Mode (require the calibration of tilt sensor beforehand, see
6.3.2. Survey with tilt sensor
for reference).
When untick Auto measure in the Survey Option screen:
5.
If the settings of the selected measurement method have been changed, tap button in the lower right corner of the Survey Option screen to save the change and go back to the Point Survey screen.
6.
Tap button, hold the range pole until the countdown timer disappears, and then move to next point to continue.
When tick Auto measure in the Survey Option screen:
C3 GNSS Receiver User Guide Page 41
5. Survey with K-COM software
Note – Users can configure the Tilt Tolerance option to define the maximum radius that the receiver can tilt and be considered in tolerance. The allowable range is 0.001m to 1.000m. And the maximum tilt angle is calculated by
arctan(Tilt Tolerance/antenna height).
5.
If the settings of the selected measurement method have been
6.
changed, tap button in the lower right corner of the Survey Option screen to save the change and go back to the Point Survey screen.
Tap
C3+) .
button in the tool bar to display the eBubble (Only Apply to
7.
Tap button → a “Waiting to move” message appears over the eBubble → tilt the range pole (exceeding the specified tilt tolerance).
8.
A “Waiting for level” message appears over the eBubble → move the receiver to the target measuring point → level the range pole.
C3 GNSS Receiver User Guide Page 42
5. Survey with K-COM software
9.
When the range pole is within the tilt tolerance, a “Waiting for stable” message appears.
10. Hold the range pole for more than 2 seconds and the point will automatically begin measuring.
11. When the countdown timer disappears, tilt the range pole outside of the tilt tolerance, and then move to next point to continue.
12. To exit the Auto Measure mode, tap button.
5.3.2. S
URVEY WITH TILT SENSOR
(
ONLY APPLY TO
C3+)
The C3 receiver is integrated with tilt sensor, which allows the use of eBubble (electronic bubble) and tilt compensation. The tilt compensation allows the collection of points even when the receiver is tilted up to 30 degrees off plumb. When the terrain or structures around the point do not allow full plumbing of the receiver, the built-in tilt sensor will compensate
C3 GNSS Receiver User Guide Page 43
5. Survey with K-COM software for the tilt of the range pole. The eBubble can be displayed in the lower left corner of any survey window within the Horizon K-COM software.
To bring the eBubble and tilt compensation into full play, it is very important to ensure the integrated tilt sensor is correctly calibrated. When calibrating the integrated tilt sensor, users need to make sure that a range pole or a tripod with tribrach have been well calibrated. The quality of the integrated tilt sensor calibration is directly related to the quality of the mechanic bubble and its calibration.
The integrated tilt sensor calibration is performed within the K-COM software. To calibrate the integrated tilt sensor, place the receiver on a stable range pole or tripod with tribrach. Level the receiver using the mechanical bubble on the range pole or tribrach.
5.3.2.1. Calibrating the tilt sensor
1.
In the main menu, tap Settings → tap Survey Options → select
Ebubble Option tab.
2.
Configure the Sensitivity, Response and Age Limit from the dropdown lists.
3.
Tap button in the lower left corner → a message will pop up asking user to confirm that the device is level → tap Yes button.
4.
A progress message will appear to indicate that the calibration is in progress.
C3 GNSS Receiver User Guide Page 44
5. Survey with K-COM software
5.
Once the calibration is complete, the green electronic bubble will be centered in the inner circle.
6.
Tap button in the lower left corner → a pop-up message will prompt user rotate the device follow the illustration during the compass calibration → tap Yes button.
7.
Perform the calibration according to the graphic displayed on the screen.
8.
Once the calibration is complete, tap
C3 GNSS Receiver User Guide button in the lower right
Page 45
5. Survey with K-COM software corner.
5.3.2.2. Measure points in compensated mode
9.
Go back to the main menu, tap Survey → tap Point Survey.
10. Enter the point name in the input frame on the top left corner.
Notes
The system will automatically increment the numeric component of the measured point name.
The measured points will be automatically incremented from “P1”, by default.
11. If necessary, enter the feature code in the input frame on the top right corner.
12. Tap button → select Compensated Mode in the pop-up window.
Notes
Users can tap button to configure the settings of the
Compensated Mode in the pop-up Survey Option screen.
The auto measure function is available for the Compensated Mode.
When untick Auto measure in the Survey Option screen:
C3 GNSS Receiver User Guide Page 46
5. Survey with K-COM software
13. If the settings of the Compensated Mode have been changed, tap button in the lower right corner of the Survey Option screen to save the change and go back to the Point Survey screen.
14. Tilt the range pole within 30 degrees off plumb → Tap button, hold the range pole until the countdown timer disappears → move to next point to continue.
Tip: The color of eBubble indicates different tilt status of the range pole. Red means the tilt of the range pole exceeds 30 degrees; however, yellow or green means the tilt is within 30 degrees or 24 degrees.
When tick Auto measure in the Survey Option screen:
C3 GNSS Receiver User Guide Page 47
5. Survey with K-COM software
13. If the settings of the Compensated Mode have been changed, tap button in the lower right corner of the Survey Option screen to save the change and go back to the Point Survey screen.
14. Tap button → a “Waiting to move” message appears over the eBubble → tilt the range pole to more than 30 degrees.
15. A “Waiting for level” message appears over the eBubble → move the receiver to the target measuring point → tilt the range pole within 30 degrees.
C3 GNSS Receiver User Guide Page 48
5. Survey with K-COM software
16. When the range pole is within 30 degrees, a “Waiting for stable” message appears → hold the range pole for more than 2 seconds and the point will automatically begin measuring.
17. When the countdown timer disappears, tilt the range pole by more than 30 degrees, and then move to next point to continue.
18. To exit the Auto Measure mode, tap button.
5.4. P
OINT ADJUST
(S
ITE CALIBRATION
)
Point adjust, also known as “site calibration”, is used to transform WGS-84 coordinates into local grid coordinates.
Notes
General speaking, if a three- or seven-parameter datum transformation has been configured for project, users can skip the
C3 GNSS Receiver User Guide Page 49
5. Survey with K-COM software
site calibration and the coordinates measured will be transformed
automatically into local grid coordinates.
If a projection and datum transformation have already been specified, users can reduce any discrepancies between the WGS-84 coordinates and the local grid coordinates by performing a site calibration.
To perform the site calibration, users need to measure the control points with GNSS receiver first.
To perform site calibration:
1.
In the main menu, tap Survey → tap Point Adjust.
2.
Tap button in the lower left corner to add point pair(s).
3.
In the pop-up screen, tap button on the upper side of the screen to add the existing GNSS point or key in a GNSS point.
4.
Tap button on the lower side of the screen to add the existing known point or key in a known point.
5.
Tap button to go down to the bottom of the page.
6.
Select the adjustment method from the dropdown list next to Method field.
C3 GNSS Receiver User Guide Page 50
5. Survey with K-COM software
Note – Users can determine whether this point pair is involved in the
computation of either horizontal or vertical adjustment, or both.
7.
Tap button in the lower right corner to save the point pair.
8.
Continue the Step 2 to Step 7 to add all the point pairs.
9.
If necessary, select the fit method for vertical adjustment from the dropdown list next to Fit Method field.
Notes
The fit methods of horizontal and vertical adjustment are “TGO” and “Fixed difference” respectively, by default.
There are four available fit methods for vertical adjustment: Fixed difference, Plane fitting, Curved surface fitting and TGO.
1. The “Fixed difference” fit method is used when the measuring surface is almost horizontal, and it requires at least 1 point pair with elevation information to be involved in the computation.
C3 GNSS Receiver User Guide Page 51
5. Survey with K-COM software
2. The “Plane fitting” fit method is used when the measuring surface is level, and it requires at least 3 point pair with elevation information to be involved in the computation.
3. The “Curved surface fitting” fit method is used when the measuring surface is uneven, and it requires at least 6 point pair with elevation information to be involved in the computation.
4. The “TGO” fit method is almost the same with “Fixed difference”, except that this method is more convenient for computation using computer.
10. Tap button to perform the calibration, and then the “HError” and
“VError” information related to each point pair will be displayed.
Note – For best results, make sure that the control points are evenly distributed to the extent of the job area.
11. Tap button → a message will pop up asking user whether to replace parameters of current project.
C3 GNSS Receiver User Guide Page 52
5. Survey with K-COM software
12. If tap YES button, the parameters calculated by this calibration will be applied to the coordinate system of the current project. Also, the Point
Adjust screen will skip to the CRS Params screen to help user check the horizontal and vertical adjustments in Plane Adjust tab and Height
Adjust tab.
Note – To check the horizontal and vertical adjustments in Plane Adjust tab and Height Adjust tab, users need to tap
function first.
button to unlock the display
C3 GNSS Receiver User Guide Page 53
5. Survey with K-COM software
Tip – The default login values of display function are “admin” for Name and
“123456” for Password.
5.5. B
ASE SHIFT
Typically, the Real-time kinematic (RTK) operation requires a data link to send observations or corrections from the base station to the rover, and then the rover will calculates its position in real time.
Within a project, when the base receiver is restarted or moved, the base coordinated system will shift each time the position of base station is changed. Normally, the coordinates determined by the base station that set up on a control point should be in the same coordinate system. However, coordinates determined by the base station that set up on an autonomous point should be carried out a base shift, which provided by Horizon K-COM software, to keep their base station coordinate the same as the initial coordinate system.
Notes – To perform the base shift, make sure that the two base stations have been linked together by at least one common point that sharing with the same position, which means that the common point not only has the coordinate determined by the initial coordinate system, but also own the coordinate surveyed from another base coordinate system that need to be shifted.
To perform a base shift:
1.
In the main menu, tap Survey → tap Base Shift.
2.
Tap button next to the GNSS Point field to select the common point surveyed from the base coordinate system that need to be
C3 GNSS Receiver User Guide Page 54
5. Survey with K-COM software shifted.
3.
Tap button next to the Known Point field to select that common point determined by the initial coordinate system.
4.
The offset information of base coordinate system that need to be shifted will be displayed automatically.
5.
Tap button → a message will pop up asking user whether to translate the coordinates determined by the current base coordinate system to the initial one.
6.
If tap YES button, all the coordinates determined by the current base coordinate system will be translated. Also, the Point Data Management screen will pop up to help user check whether the coordinates determined by the current base coordinate system have changed.
C3 GNSS Receiver User Guide Page 55
5. Survey with K-COM software
Note – The coordinates translated are local grid coordinates rather than
WGS-84 coordinates.
5.6. D
ATA EXPORT
1.
In the main menu, tap Project → tap Export.
2.
Select one data format (for example, Custom Format) according to your requirement.
3.
Tick the point type(s) → enter the File Name → select the File Type from the dropdown list → select the path that used to store the file.
4.
Tap button → the software will prompt whether the file has been successfully exported.
C3 GNSS Receiver User Guide Page 56
5. Survey with K-COM software
Notes
When select custom format, users can tap button next to File
Tpye field to define the file format according to your requirement.
After the file has been successfully exported in the controller, connect the controller to the office computer for file transfer (please refer to corresponding user guide of the controller that you are using for instruction) and post-processing.
5.7. R
ECEIVER REGISTRATION
When the software prompt that the receiver is overdue, users need to contact your local dealer to get the registration code.
To register the receiver:
1.
In the main menu, tap Device → tap Device Info.
2.
Tap button in the lower left corner.
3.
Enter the registration code in the pop up window.
C3 GNSS Receiver User Guide Page 57
5. Survey with K-COM software
4.
Tap Finish button to complete the registration, and then the software will show the expire date.
C3 GNSS Receiver User Guide Page 58
6. C
ONFIGURING THROUGH A WEB BROWSER
Supported browsers:
Google Chrome
Microsoft Internet Explorer version 10, or higher
To connect to the receiver through a web browser:
1. Turn on the Wi-Fi of the receiver.
2. Search the wireless network named as GNSS-XXXXXXX (the SN of your receiver) on your computer, and then establish the connection.
3. After the successful connection between your computer and the receiver, enter the IP address of the receiver into the address bar of the web browser on your computer:
4. The web browser prompts you to enter a login account and password:
The default login account for the receiver is:
Login Account: admin
Password: password
Note – Tick remember me option, and then the browser will remember the
Login Account and Password you entered for the next time you enter this login screen.
5. Once you are logged in, the web page appears as follows:
C3 GNSS Receiver User Guide Page
59
6. Configuring through a web browser
This web page shows the configuration menus on the left of the browser window, and the setting on the right. Each configuration menu contains the related submenus to configure the receiver and monitor receiver performance.
This chapter describes each configuration menu.
To view the web page in another language, select the corresponding language name from the dropdown list on the upper right corner of the web page.
Currently, three languages are available:
6.1. S
TATUS MENU
This menu provides a quick link to review the receiver's position information, satellites tracked, runtime, current data log status, current outputs, available memory, and more.
C3 GNSS Receiver User Guide Page 60
6. Configuring through a web browser
6.1.1. P
OSITION SUBMENU
This page shows the relevant position information about the receiver's position solution which including the position, DOP values, satellites used and tracked, and the receiver clock information.
6.1.2. O
PERATION SUBMENU
Lists several important items to help you understand how the receiver is being used and its current operating condition. Items include the identities of currently tracked satellites, internal and external storage usage rate, how long the receiver has been operational, state of the internal battery, power source state, files being logged, and data streams being output. With this information, it is easy to tell exactly what functions the receiver is performing:
C3 GNSS Receiver User Guide Page 61
6. Configuring through a web browser
6.1.3. G
OOGLE
M
AP SUBMENU
Tap this submenu to show the location of the receiver on Google map.
C3 GNSS Receiver User Guide Page 62
6. Configuring through a web browser
6.2. S
ATELLITES MENU
Use the Satellites menu to view satellite tracking details and enable/disable
GPS, SBAS, GLONASS, BDS and Galileo constellations. These menus include tabular and graphical displays to provide all required information on satellite tracking status.
6.2.1. S
ATELLITE
T
RACK
T
ABLE SUBMENU
Provides the status of satellites tracked in general, such as the satellite ID, satellite type, attitude angle, azimuth angle, L1 SNR, L2 SNR, L5 SNR and enable/disable status of each one.
C3 GNSS Receiver User Guide Page 63
6. Configuring through a web browser
6.2.2. S
ATELLITE
T
RACK
D
IAGRAM SUBMENU
The following figure is an example of satellite track diagram page. Users can determine the satellite types and the corresponding SNR of L-band carriers to be displayed in any combination.
6.2.3. S
KY
P
LOT SUBMENU
The following figure is an example of Skyplot page.
6.3. R
ECEIVER
S
ETTINGS MENU
C3 GNSS Receiver User Guide Page 64
6. Configuring through a web browser
Use this menu to configure settings such as the antenna type and height, elevation mask and PDOP setting, the reference station coordinates, receiver resetting and web interface language:
6.3.1. I
NTRODUCTION SUBMENU
This submenu shows the receiver information and reference station information, including antenna related information, elevation mask angle, reference station work mode and position, etc.
6.3.2. A
NTENNA
P
ARAM
S
ETTINGS SUBMENU
Use this screen to configure all of the items relating to the GNSS antenna.
You must enter the correct values for all antenna-related fields, as the choices you make significantly affect the accuracy for logged data and broadcast correction data:
C3 GNSS Receiver User Guide Page 65
6. Configuring through a web browser
6.3.3. R
EFERENCE
S
TATION
S
ETTINGS SUBMENU
Use this screen to configure settings such as the station coordinates and the broadcast station identifiers. You must enter accurate information in these fields, as this data significantly affects the accuracy of logged data files and broadcast correction data:
C3 GNSS Receiver User Guide Page 66
6. Configuring through a web browser
For Reference Station Mode:
There are three modes available: a) Auto Rover: The receiver will serve as a rover after this mode is enabled, and then receive correction data through the working mode set last time.
b) Auto Base: The receiver will serve as a base after this mode is enabled, and then broadcast correction data based on coordinate inputted by user, or obtained through autonomous positioning automatically.
c) Manual Base: The receiver will serve neither as a base or a rover after this mode is enabled. Users need to configure the receiver manually.
For Reference Latitude and Reference Longitude:
There are mainly three methods to enter the reference coordinates and shown as follows: a) Acquire Current Position: Click this button to acquire current position obtained through autonomous positioning automatically.
b) Manual Input: Manually input the coordinate of a control point.
c) From CORS: After the receiver logging in CORS, the software can record the coordinate of current position based on fix solution.
For Sample for Average:
C3 GNSS Receiver User Guide Page 67
6. Configuring through a web browser
Users can determine the positioning limit and sampling amount. The positioning limit falls into two types: a) Single Solution Coordinates: Collect the coordinates of receiver obtained through autonomous positioning.
b) Fixed Solution Coordinates: Only collect coordinates of receiver with a fixed solution.
After the configuration of positioning limit and sampling amount, click to carry out sampling and averaging → the progress bar will show the progress → the result will be served as the coordinate of current positon.
If users need to save the changes, please tap button.
6.3.4. R
ECEIVER
R
ESET SUBMENU
Use this screen to completely or partially reset the receiver:
6.3.5. L
ANGUAGES SUBMENU
Use this screen to select the web interface language:
6.4. D
ATA
R
ECORDING MENU
Use the Data Logging menu to set up the receiver to log static GNSS data and to view the logging settings. You can configure settings such as observable rate, recording rate, continuous logging limit, and whether to auto delete old
C3 GNSS Receiver User Guide Page 68
6. Configuring through a web browser files if memory is low. This menu also provides the controls for the FTP push feature:
6.4.1. L
OG
S
ETTINGS SUBMENU
Shows the data logging status, internal and external storage usage and data logging status of each session. Also, users can configure the data logging settings for each session, including recording name, store location, storage limit, store formats, start time, etc.
To edit the settings of each session, click the Modify button to the right of the required session, and then the Recording Edit screen appears:
C3 GNSS Receiver User Guide Page 69
6. Configuring through a web browser
In this screen, you can configure all the data logging parameters, and determine whether the recording files will be affected by the FTP Push.
The parameters are mainly as follows:
Recording Name: The name of this logging session.
Sample Interval: Select the observable rate from the dropdown list.
Store Location: Determine whether to store at internal storage or
external storage.
Start Time: Set the start time of data logging in UTC. Select Yes or
No option below to determine whether to start data logging from
the start time defined, or immediately after this session is switched on.
Duration Time: Set the duration of data logging.
Storage: Set the storage space of this session.
Recycle Storage: Select Yes or No option to determine whether to
auto delete old files if the storage space is full.
Storage Format: Set the data format of the logged data.
FTP Push: Decide whether to push the stored files to the FTP server
of your choice.
Tap button to save the settings and back to the Log Settings screen. Also, users can click and back to Log Settings screen.
to abandon the changed settings
Note – To modify data logging parameters, make sure the data logging
C3 GNSS Receiver User Guide Page 70
6. Configuring through a web browser
session is switched off.
To switch on or off ANY data logging session, tap the ON or OFF button to the right of the required session.
To delete the recorded files of ANY data logging session, tap the Clear button to the right of the required session.
To delete the recorded files of ALL data logging sessions, tap the Clear ALL
Accounts button.
6.4.2. FTP P
USH
S
ETTINGS SUBMENU
Use this screen to configure the receiver to push stored files to the FTP server of your choice. Only files that are configured to use FTP push are transmitted.
Tap Modify button to the right of the required FTP server and the FTP Push
Settings screen appears:
6.4.3. FTP P
USH
R
ECORDING SUBMENU
Shows the related information about the recorded filed that be pushed. And users can tap Clear Ftp Send Log button in the upper right corner to clear the log of FTP Push operations.
C3 GNSS Receiver User Guide Page 71
6. Configuring through a web browser
6.4.4. D
ATA
D
OWNLOAD SUBMENU
In this submenu, users can download the data files that recorded in the internal storage through the internal FTP site.
1. Click this submenu, and then the log on dialogue box will prompt you to enter a user name and password:
The default logon account for the internal FTP site is:
User name: ftp
Password: ftp
2. Click the directory named as “repo” to view and download the files currently stored on the receiver:
3. To find the file need to be downloaded, click the name of data logging session → the date of file that be recorded → the format of the file → the name of the target file.
C3 GNSS Receiver User Guide Page 72
6. Configuring through a web browser
4. To download a file, left-click the name of the target file → download the file according to the prompts.
6.5. IO S
ETTINGS MENU
Use the IO Settings menu to set up all receiver outputs and inputs. The receiver can output CMR, RTCM, Raw data, Ephemeris data, GPGGA, GPGSV, on TCP/IP, UDP, serial port, or Bluetooth ports.
6.5.1. IO S
ETTINGS SUBMENU
The following figure shows an example of the screen that appears when you select this submenu.
C3 GNSS Receiver User Guide Page 73
6. Configuring through a web browser
In this submenu, users can configure 6 types of input and output settings.
1. RTK Client
After configuring the settings of RTK client, users can log on CORS or APIS.
Tap the Connect button to the right → the IO Settings screen will appear → choose one of the connection protocols among the NTRIP, APIS_BASE and
APIS_ROVER → configure the related parameters → click log on CORS or APIS.
to
Connection Protocol: NTRIP
Connection Protocol: APIS_BASE
Connection Protocol: APIS_ROVER
C3 GNSS Receiver User Guide Page 74
6. Configuring through a web browser
2. TCP/UDP Client
Tap the Connect button to the right of required TCP/UDP Client → the IO
Settings screen will appear → select the connection protocol between TCP and UDP → enter the IP and Port of the target server → configure messages that you want to output to the target server → click and complete the connection.
to save
3. TCP Server/NTRIP Caster
Tap the Connect button to the right of required TCP Server/NTRIP Caster → the IO Settings screen will appear → select one of the connection protocols between NTRIP and TCP → configure the other related parameters → click to save the settings and open the server.
Connection Protocol: NTRIP
C3 GNSS Receiver User Guide Page 75
6. Configuring through a web browser
Connection Protocol: TCP
4. COM Port
Tap the Settings button to the right of COM Port → the Serial Port Setup screen will appear → select Baud Rate used to transmit data → configure the messages that you want to output through the serial port → click to save the settings and start to transmit.
C3 GNSS Receiver User Guide Page 76
6. Configuring through a web browser
5. Bluetooth
Tap the Settings button to the right of Bluetooth → the Bluetooth Set screen will appear → configure the messages that you want to transmit through
Bluetooth → click to save the settings and start to transmit.
6. Radio
Tap the Settings button to the right of Radio → the Radio Settings screen will appear → select the format of differential data that you want to transmit through radio from the dropdown list → click
C3 GNSS Receiver User Guide to save the
Page 77
settings and start to transmit.
6. Configuring through a web browser
6.6. GPRS
MENU
Use this menu to check and configure the network settings:
6.6.1. N
ETWORK
I
NFO SUBMENU
The following figure shows an example of the screen that appears when you select this submenu:
6.6.2. N
ETWORK
S
ET SUBMENU
Use this submenu to configure network settings, including GPRS model status, network mode, dialing status, APN, etc.
C3 GNSS Receiver User Guide Page 78
6. Configuring through a web browser
6.7. W
IFI MENU
Use this menu to check and configure the Wifi settings:
6.7.1. W
IFI
I
NFO SUBMENU
The following figure shows an example of the screen that appears when you select this submenu:
C3 GNSS Receiver User Guide Page 79
6. Configuring through a web browser
6.7.2. W
IFI
S
ETTINGS SUBMENU
Use this submenu to configure the related parameters of the Wi-Fi settings, including power status, wifi mode, encrypt type, password, etc.
6.8. B
LUETOOTH
S
ET MENU
Use this menu to configure Bluetooth settings.
6.8.1. B
LUETOOTH
S
ET SUBMENU
The following figure shows an example of the screen that appears when you select this submenu:
6.9. R
ADIO
S
ETTINGS MENU
Use this menu to check and configure radio related settings, including protocol, OTA baud rate, frequency, etc.
C3 GNSS Receiver User Guide Page 80
6. Configuring through a web browser
6.9.1. R
ADIO
I
NFO SUBMENU
The following figure shows an example of the current configuration information about the internal radio:
6.9.2. R
ADIO
S
ETTINGS SUBMENU
Use this submenu to configure radio settings, including radio status, whether to switch on auto start or not, protocol, transmitting power, radio frequency, etc.
6.10. N
ETWORK
S
ERVICE MENU
Use this menu to configure the receiver’s HTTP port, and the username and
C3 GNSS Receiver User Guide Page 81
password of internal FTP site:
6. Configuring through a web browser
6.10.1. HTTP
SUBMENU
The following figure shows an example of the screen that appears when you select this submenu:
6.10.2. FTP S
ERVICE SUBMENU
The following figure shows an example of the screen that appears when you select this submenu:
6.11. F
IRMWARE MENU
Use this menu to check the current firmware information, download the system log, update the receiver firmware, download or update the configuration file and register the receiver, and more:
C3 GNSS Receiver User Guide Page 82
6. Configuring through a web browser
6.11.1. F
IRMWARE
I
NFO SUBMENU
Use this submenu to check the current firmware information. The following figure shows an example of the firmware information.
6.11.2. S
YSTEM
L
OG SUBMENU
Use this submenu to download the system log of the receiver.
6.11.3. F
IRMWARE
U
PDATE SUBMENU
Use this submenu to load new firmware to the receiver across the network.
Tap the Browse button to locate the upgrade file → tap Confirm button to confirm the selected upgrading file and start upgrading.
C3 GNSS Receiver User Guide Page 83
6. Configuring through a web browser
Notes
It may take about 3 or 4 minutes to complete the firmware upgrading. Do not touch the power button or unplug the power until the upgrading process is finished, or damage will be caused to the receiver.
The receiver will restart after the firmware upgrading is done, so users need to reconnect the receiver with your computer via Wi-Fi, and then log-in the receiver through a web browser to continue the configuration.
6.11.4. C
ONFIG
F
ILE SUBMENU
In this submenu, users can download the configuration file by tapping button and determine a saving path to download the configuration file (.cfg file). Also, users can tap the Browse button to locate the existing configuration file → tap Confirm button to confirm the selected file and start updating.
6.11.5. GNSS R
EGISTRATION SUBMENU
Use this submenu to register the receiver. Paste or enter the registration code to the Registration Code field → tap Registration button to complete the registration.
6.11.6. T
HE
H
ARDWARE
V
ERSION SUBMENU
Use this submenu to check the hardware information, including main board version and core board version:
C3 GNSS Receiver User Guide Page 84
6. Configuring through a web browser
C3 GNSS Receiver User Guide Page 85
A. C
OMMUNICATION PORTS DEFINITION
A.I.
KRONOS C
3
RECEIVER
IO
PORT
(7-
PIN
L
EMO PORT
)
DEFINITION
5
6
7
PIN FUNCTION
1 Ground ( - )
2
3
4
Ground ( - )
RS232-TX (Output)
Not Used
Not Used
VIN
RS232-RX (Input)
A.II.
KRONOS C
3
RECEIVER
USB
PORT
(7-
PIN
L
EMO PORT
)
DEFINITION
5
6
7
PIN FUNCTION
1 Ground ( - )
2
3
4
Ground ( - )
VBUS
DM
DP
VIN
ID
C3 GNSS Receiver User Guide Page
86
C3 GNSS Receiver User Guide Page
87
تنزيل
تم تحديث الرابط العام
رابط عام للمستند
إعلان
