advertisement
HARDWARE SPECIFICATION, DV-518GSC-xxx,Rev. A
MODEL DV-518GSC-xxx
DVD-ROM DRIVE
HARDWARE SPECIFICATION
Rev. A
27 sheets in Total
HARDWARE SPECIFICATION, DV-518GSC-xxx,Rev. A
TABLE OF CONTENTS
Title Page
1. SCOPE.................................................................................................................................................................. 3
2. OUTLINE .............................................................................................................................................................. 3
3. CONSTRUCTION ................................................................................................................................................ 4
3.1 External Construction ...................................................................................................................................................................................... 4
3.2 Front Bezel ....................................................................................................................................................................................................... 5
3.3 Installation ......................................................................................................................................................................................................... 6
4. DISC SPECIFICATION ........................................................................................................................................ 7
4.1 Applicable Disc Formats .................................................................................................................................................................................. 7
4.2 Rotational Speed ............................................................................................................................................................................................. 8
4.3 Data Capacity................................................................................................................................................................................................... 9
4.4 Write Methods ................................................................................................................................................................................................ 10
5. PERFORMANCE ............................................................................................................................................... 11
5.1 Operating Performance................................................................................................................................................................................. 11
5.2 Mechanism ..................................................................................................................................................................................................... 12
6. ENVIRONMENTAL CONDITIONS ................................................................................................................... 13
6.1 Ambient Temperature/relative Humidity ....................................................................................................................................................... 13
6.2 Vibration .......................................................................................................................................................................................................... 14
6.3 Shocks ............................................................................................................................................................................................................ 14
6.4 Noise ............................................................................................................................................................................................................... 15
6.5 Transportation Condition ............................................................................................................................................................................... 15
7. RELIABILITY ...................................................................................................................................................... 16
7.1 General ........................................................................................................................................................................................................... 16
7.2 Safety Standard ............................................................................................................................................................................................. 16
7.3 EMC ................................................................................................................................................................................................................ 16
8. INDICATOR AND STRAP FUNCTIONS .......................................................................................................... 17
8.1 Indicator .......................................................................................................................................................................................................... 17
8.1.1 Location ............................................................................................................................................................................................... 17
8.1.2 Indicator function ................................................................................................................................................................................. 17
9. FRAME GROUNDING ...................................................................................................................................... 17
10. POWER INTERFACE ...................................................................................................................................... 18
10.1 Power Supply Used .................................................................................................................................................................................... 18
10.2 Current Consumption .................................................................................................................................................................................. 18
10.3 Power Supply Sequence ............................................................................................................................................................................ 18
10.4 Power Interface Connector ......................................................................................................................................................................... 19
1 / 26
HARDWARE SPECIFICATION, DV-518GSC-xxx,Rev. A
11. SATA HARDWARE INTERFACE ................................................................................................................... 20
11.1 Applicable Standard ..................................................................................................................................................................................... 20
11.2 Electrical Characteristics .............................................................................................................................................................................. 20
11.3 Signal Interface Connector .......................................................................................................................................................................... 20
12. REQUESTS RELATING TO THE FCC RULE PART (15) AND SAFETY LASER PRODUCTS .............. 21
12.1 FCC Rule Part (15) ...................................................................................................................................................................................... 21
12.2 Safety of Laser Products ............................................................................................................................................................................. 22
12.3 Attachment Location .................................................................................................................................................................................... 22
13. ROHS COMPLIANCE ..................................................................................................................................... 23
14. LABEL USED .................................................................................................................................................. 24
15. PACKAGING .................................................................................................................................................... 25
2 / 26
HARDWARE SPECIFICATION, DV-518GSC-xxx,Rev. A
1. SCOPE
This is hardware specification of the TEAC DV-518GSC-xxx DVD-ROM DRIVE (hereinafter referred to as drive).
2. OUTLINE
The outline of this DVD-ROM DRIVE is given in Table 2-1 .
Model name
TEAC Part Number
Applicable Safety standards
Applicable EMC standards
Supported Data transfer rate at the maximum
Maximum Access time at random access
Disc speed
Signal interface
Power source
Power consumption
Disc loading method
Start time
Applicable disc format
Write Methods
Buffer under run prevention function
(Table 2-1) Outline of the specification
DV-518GSC-xxx
1977291x-xx
UL
FCC
CSA
CE
TÜV
RCM
NEMKO
BSMI
CB
KCC
FDA
PIO 4 DMA 2 UDMA 2 UDMA 3 UDMA 4 UDMA 5 S-ATA S-ATA II
Stamped CD-ROM [ms] Stamped DVD-ROM [ms]
140
Stamped CD-ROM [rpm]
Serial ATA
Approx. 9660
160
Stamped DVD-ROM [rpm]
Approx. 10450
+5 [V] DC system +12 [V] DC system
26 [W] Max.
Disc tray
18 [sec] or less
Refer to Table 4.1-1
Refer to Table 4.4-1
Provided
Readable disc
Recordable disc
CD
DVD
CD
DVD
DA
ROM
R
+R
ROM
+R
R RW
+R DL +RW
RW
+R DL +RW -R
-R
-R DL
-R DL -RW
-RW RAM
RAM
Front bezel and door
Eject button
Tray
Front indicator color
Refer to Table 3.2-1
Audio lineout
Default strap setting
Laser class
RoHS directive
Green (Refer to Table 8.1.2-1 )
Audio Line Output [Vrms]
Not provided
NA
Class 1 laser product
Complies with
Impedance [kΩ]
NA
3 / 26
HARDWARE SPECIFICATION, DV-518GSC-xxx,Rev. A
3. CONSTRUCTION
3.1 External Construction
L
170+/-0.5
(Table 3.1-1) External Construction
W
Dimension [mm]
H
148.4+0.4/-0 42.2+/-0.3
Net Weight [kg]
Typical 0.570
Figure
Fig.3.1-1
(Fig. 3.1-1) External view of the drive
4 / 26
HARDWARE SPECIFICATION, DV-518GSC-xxx,Rev. A
3.2 Front Bezel
(1) The color of the front bezel, the door, the tray and eject button are shown in Table 3.2-1 .
(Table 3.2-1) Color and Logo marks
Version
DV-518GSC-xxx
-002
-100
Bezel
PS2
Black
Door
PS2
Black
(2) The logo mark indication is shown in Fig.3.2-1 .
Color
Eject button
PS2
Black
Tray
PS2
Black
TEAC Logo
No
No
(Fig. 3.2-1) Front bezel without the logo marks indicated
5 / 26
HARDWARE SPECIFICATION, DV-518GSC-xxx,Rev. A
3.3 Installation
The drive operation specification shall be satisfied with the installation method described below.
(1) Installation direction
The drive operation specification shall be satisfied using the following two drive positions.
(a) Position where the disc is placed horizontally.
Note: The front indicator shall be in the left side. The tilt shall be10° or less in all directions.
(b) Position where a disc is vertical. The tilt shall be 10° or less in all directions.
(2) Mounting method
The mounting holes at the drive side and bottom shall be used for mounting (Refer to Fig.3.1-1 ).
(a) Screw hole : Left side 4-M3
: Right side 4-M3
: Bottom side 4-M3
(b) Tightening torque
(c) Screw insertion depth
: 3 to 4 [kg-cm]
: 7 [mm] or less (side mount)
4 [mm] or less (bottom mount)
6 / 26
HARDWARE SPECIFICATION, DV-518GSC-xxx,Rev. A
4. DISC SPECIFICATION
4.1 Applicable Disc Formats
The read and write of the following disc formats apply to the drive.
(Table 4.1-1) Applicable disc formats
CD
DVD
Disc format
CD-DA
CD-ROM Mode1
CD-ROM XA Mode2 (Form1,Form2)
CD-I
Mixed mode CD-ROM
PHOTO CD
CD-Extra
Video CD
CD-Text
DVD-Video
DVD-Audio
DVD-R
DVD-R DL
DVD-RW
DVD+R
DVD+R DL
DVD+RW
DVD-RAM
Read capability
Supported
Supported
Supported
Supported
Supported
Supported
Supported
Supported
Supported
Supported
Supported
Supported
Supported
Supported
Supported
Supported
Supported
Supported
Write capability
NA
NA
NA
NA
NA
NA
NA
NA
NA
NA
NA
NA
NA
NA
NA
NA
NA
NA
7 / 26
HARDWARE SPECIFICATION, DV-518GSC-xxx,Rev. A
4.2 Rotational Speed
The rotational speed in each mode shall be in accordance with Table 4.2-1 and Table 4.2-2 As for the rotational speed at the write mode, the speed described in Table 4.2-3 and Table 4.2-4 shall be settable.
CD
DVD
Media
CD-ROM
CD-DAE
Video CD
Finalized CD-R Data
Finalized CD-RW
Un-Finalized CD-R
Un-Finalized CD-RW
DVD-ROM
DVD-ROM DL
DVD-R
DVD-R DL
DVD-RW
DVD+R
DVD+R DL
DVD+RW
DVD-RAM
(Table 4.2-1) Rotational speed (Read mode)
Normal read speed
20x - 48x
20x - 48x
20x - 48x
20x - 48x
16x - 40x
8x
8x
6x - 18x
5x - 8x
6x - 16x
2.5x - 8x
5x - 12x
6x - 16x
2.5x - 8x
5x - 12x
2x - 5x
Method
Full CAV
Full CAV
Full CAV
Full CAV
Full CAV
Full CAV
Full CAV
Full CAV
Full CAV
Full CAV
Full CAV
Full CAV
Full CAV
Full CAV
Full CAV
Full CAV
CD
DVD
(Table 4.2-2) Rotational speed (Playback mode)
Media
CD-DA
Video CD
DVD-ROM
DVD-ROM DL
DVD-R
DVD-RW
DVD+R
DVD+RW
DVD-RAM
Normal playback speed
6.5x - 16x
6.5x - 16x
2.5x - 6x
2.5x - 6x
2.5x - 6x
2.5x - 6x
2.5x - 6x
2.5x - 6x
2x - 5x
Method
Full CAV
Full CAV
Full CAV
Full CAV
Full CAV
Full CAV
Full CAV
Full CAV
Full CAV
8 / 26
HARDWARE SPECIFICATION, DV-518GSC-xxx,Rev. A
(Table 4.2-3) Rotational speed for CD (Write mode)
Media
CD-R
Multi speed CD-RW
High speed CD-RW
Ultra speed CD-RW
Ultra speed plus CD-RW
Selection speed
NA
NA
NA
NA
NA
Write speed
NA
NA
NA
NA
NA
Method
NA
NA
NA
NA
NA
(Table 4.2-4) Rotational speed for DVD (Write mode)
Media
DVD-R
DVD-R DL
DVD-RW
DVD+R
DVD+R DL
DVD+RW
DVD-RAM
Selection speed
NA
NA
NA
NA
NA
NA
NA
Write speed
NA
NA
NA
NA
NA
NA
NA
Method
NA
NA
NA
NA
NA
NA
NA
4.3 Data Capacity
Data capacity shall be in accordance with Table 4.3-1 for each disc format.
CD
DVD
(Table 4.3-1) Data capacity
Disc formats Applicable capacity
CD-ROM Mode 1
CD-ROM XA Mode 2 Form 1
650 [MB]
700 [MB]
650 [MB]
700 [MB]
CD-ROM XA Mode 2 Form 2
738 [MB]
795 [MB]
CD-DA
74 [min]
79 [min]
DVD-ROM, DVD-Video, DVD+/-R, DVD+/-RW 4.7 [GB]/side
DVD-ROM, DVD-Video DL
DVD-RAM
8.5 [GB]/side
4.7 [GB]/side
9 / 26
HARDWARE SPECIFICATION, DV-518GSC-xxx,Rev. A
4.4 Write Methods
CD
DVD
Media
CD-R
CD-RW
DVD-R
DVD-R DL
DVD-RW
DVD+R
DVD+R DL
DVD+RW
DVD-RAM
(Table 4.4-1) Write methods
Write methods
NA
NA
NA
NA
NA
NA
NA
NA
NA
10 / 26
HARDWARE SPECIFICATION, DV-518GSC-xxx,Rev. A
5. PERFORMANCE
5.1 Operating Performance
(1) Access time
The performance specified in Table 5.1-1 applies to the access time of the drive.
Mode
Random access time
Random seek time
1/3 stroke access time
Full stroke access time
(Table 5.1-1) Access time
Media
DVD
CD
DVD
CD
DVD
CD
DVD
CD
Max. [msec]
180
140
180
140
160
140
300
250
(2) Rotational speed
The performance specified in Table 5.1-2 applies to the rotational speed of the drive.
(Table 5.1-2) Rotational speed
Item
Stamped CD-ROM
Stamped DVD-ROM
Rotational speed [rpm]
Approx . 9660
Approx. 10450
(3) Data transfer rate (asynchronous)
The performance specified in Table 5.1-3 applies to the data transfer rate in each mode of the drive.
S-ATA
S-ATA II
Mode
(Table 5.1-3) Transfer rate
Max. [MB/s]
150
300
Support
Supported
Not Supported
(4) Start/stop time
The performance specified in Table 5.1-4 applies to the start/stop time of the drive.
11 / 26
HARDWARE SPECIFICATION, DV-518GSC-xxx,Rev. A
Start/stop time
Start time
Stop time
(Table 5.1-4) Start/stop time
Media
DVD-ROM
12 [cm]
8 [cm]
Photo CD
DVD-ROM
All media
Max. [sec]
18
18
18
18
9
9
Condition
Including Tray in, spin up and read TOC
Including Spin down and tray out
(5) Data buffer capacity
198 [KB] Max. in all operation modes.
5.2 Mechanism
(1) Loading mechanism
(a) TRAY loading method
• Automatic loading with the eject button
• Automatic loading with the press of the tray
• Automatic loading with the interface command
(b) TRAY ejection method
• Automatic ejection with the eject button
• Automatic ejection with the interface command
Manual ejection with the emergency hole (used with the emergency power off).
(2) Disc Loading/ejection Method
(a) When inserting a disc, place it on the tray from the back side first and the front side is pressed to the tray lightly. Or place the front side of it on the tray first, then pull toward the front to set it.
(b) When taking out the disc, pull it toward the top direction without applying excessive force.
(c) An 8cm disc can be used by placing it on the specified center position described in “3.3 Installation” when the drive is in a horizontal position. Then the disc position should not be shifted when ejecting the tray.
It cannot be used when the drive is in a vertical position.
12 / 26
HARDWARE SPECIFICATION, DV-518GSC-xxx,Rev. A
6. ENVIRONMENTAL CONDITIONS
The environmental conditions specified in this item apply to the drive excluding the disc.
The environmental conditions for discs shall be in accordance with the applicable specification.
6.1 Ambient Temperature/relative Humidity
The conditions specified in Table 6.1-1 apply to the drive.
Drive state
During non-operation
(Table 6.1-1) Ambient temperature/ relative humidity conditions
During operation
Item
Ambient temperature
Relative humidity
Wet-bulb temperature
Ambient temperature
Relative humidity
Wet-bulb temperature
Ambient temperature
Relative humidity
Wet-bulb temperature
Min.
5
20
–
–20
10
–
–40
5
–
Typ.
–
–
–
–
–
–
–
–
–
Max.
45
80
29
60
85
32
65
90
32
Unit
°C
%RH
°C
°C
%RH
°C
°C
%RH
°C
Condition
Non-condensation, 10
[°C/hour] or less 10
[%RH/hour] or less during operation
Non-condensation, 10
[°C/hour] or less 10
[%RH/hour] or less
Non-condensation, 20
[°C/hour] or less 20
[%RH/hour] or less
During
Transportation
(in package)
13 / 26
6.2 Vibration
The conditions specified in Table 6.2-1 apply to the drive.
Drive condition
(Table 6.2-1) Vibration condition
Acceleration
Test conditions
Frequency Directions
4.9 [m/s
2
] (0.5G)
During operation
CD/DVD ROM
CD-DA
CD-R/RW
DVD+/-R/RW
DVD-RAM
During non-operation
2.94 [m/s
2
] (0.3G)
19.6 [m/s
2
] (2G)
10 to 500 [Hz] X, Y and Z axes
During transportation 19.6 [m/s
2
] (2G) 10 to 500 [Hz]
HARDWARE SPECIFICATION, DV-518GSC-xxx,Rev. A
X, Y and Z axes
Requirement
Shall be free from any errors during operation.
Shall be free from damage after test.
Shall be free from damage after test.
6.3 Shocks
The conditions described in Table 6.3-1 apply to the drive.
Drive condition
During operation
CD-ROM
CD-DA
CD-R/RW
DVD+/-R/RW
DVD-RAM
During non-operation
(Table 6.3-1) Shock conditions
Test conditions
Pulse wave Number of pulses Acceleration
49.0 [m/s
2
] (5G)
19.6 [m/s
2
] (2G)
19.6 [m/s
2
] (2G)
11 [msec]
(half-sine wave)
5 times in the directions of X, Y and Z axes.
During transportation
490 [m/s
2
] (50G)
Height
Direction
2 [msec]
(half-sine wave)
60 [cm]
1 time per each surface
1 corner, 3 edges, 6 surfaces
Requirement
Shall be free from any errors during operation.
Shall be free from damage after test.
Shall be free from damage after test.
14 / 26
HARDWARE SPECIFICATION, DV-518GSC-xxx,Rev. A
6.4 Noise
The conditions described in Table 6.4-1 apply to the drive.
(Table 6.4-1) Noise conditions
Specification
Measurement position
Condition
Test disc Operation
55 [dBA] or less unbalance at 50 [cm] distance A-BEX SCD-3228, 2.5 [g-mm] Sequential read by playing
6.5 Transportation Condition
The drive package shall conform to the Appropriate Package Test Level 2 specified in JIS-Z0200 when using the specified packing box.
15 / 26
HARDWARE SPECIFICATION, DV-518GSC-xxx,Rev. A
7. RELIABILITY
7.1 General
(Table 7.1-1) Reliability conditions
Item Specification
MTBF
MTTR
Data read error rate
Seek mechanism life
Loading/eject life
Designed life
70000 [POH]
Typical 30 [minutes]
CD-ROM
Block/10
12
[bits]
Block/10
9
[bits]
DVD-ROM Block/10
15
[bits]
1,000,000 [times]
10,000 [times]
5 [years]
7.2 Safety Standard
The drive complies with the following safety standards.
Condition at normal temperature and humidity; duty 25 [%]
MODE1 and MODE2 Form1
MODE2 Form2 and CD-DA
UL
Safety standard
CSA
TÜV
FDA (DHHS)
Nemko
CB-Scheme
(Table 7.2-1) Safety standard
UL60950
CAN/CSA22.2
No.60950-1
EN60950
EN60825-1
21CFR Subchapter J
NA
IEC60950-1
IEC60825-1
Standard No.
7.3 EMC
The drive complies with the following standards.
(Table 7.3-1) EMC
EMC standard
FCC
BSMI
RCM
KCC
CE
Region
USA
Taiwan
Austria
Korea
European
Standard No.
Part 15 Class B, CISPR22
ANSI C63.4 , ICES-003
CNS 13438 Class B
AS/NZS CISPR 22 Class B
KN22, KN24, KN61000
EN55022 Class B
EN55024
EN61000
IEC61000
Provided
Provided
Provided
Provided
Provided
Provided
Not Provided
Provided
Provided
Provided
Provided
Provided
Provided
Provided
Provided
Provided
Provided
Provided
16 / 26
HARDWARE SPECIFICATION, DV-518GSC-xxx,Rev. A
8. INDICATOR AND STRAP FUNCTIONS
8.1 Indicator
8.1.1 Location
The indicator is located below the left side of the disc insertion slot on the front bezel.
8.1.2 Indicator function
The following indicator functions apply to each LED of the drive.
(Table 8.1.2-1) Functions of indicator
Operation mode
During read/Data transfer
During audio play
During seek
At start (Power ON of PC)
When the tray is opened
When the tray is closed
Indicator
Green LED lights.
Green LED blinks.
Green LED blinks.
Green LED lights.
Green LED lights.
Green LED lights.
9. FRAME GROUNDING
The drive frame is electrically connected to 0 [V] dc.
17 / 26
HARDWARE SPECIFICATION, DV-518GSC-xxx,Rev. A
10. POWER INTERFACE
10.1 Power Supply Used
The following specification applies to the power interface connector terminals of the drive. The voltage applied to the power terminal shall be defined in Table 10.1-1 and the drive shall operate normally with the voltage.
Item
Operating voltage range
Allowable ripple
(Table 10.1-1) Power voltage specification
+5 [V] DC system
+/-5 [%] (4.75 ~ 5.25 [V])
100 [mVp-p] or less
+12 [V] DC system
+/-10 [% ] (10.8 ~ 13.2 [V])
200 [mVp-p] or less
10.2 Current Consumption
The following current consumption specifications apply to the drive.
Operation
During read
During seek
During spin up
While idling
During sleep
During loading/ejection
During write
(Table 10.2-1) Current consumption
+5 [V] DC system
Form Value [A]
Average
Peak
Peak
Peak
Average
Peak
Average
0.60
1.50
0.76
1.60
0.09
0.80
NA
+12 [V] DC system
Form Value [A]
Average
Peak
Peak
Peak
Average
Peak
Average
0.92
1.30
2.30
0.52
0.03
1.50
NA
Condition
Excluding pulses of 10 [ms] or less
Excluding pulses of 10 [ms] or less
Excluding pulses of 10 [ms] or less
Excluding pulses of 10 [ms] or less
Excluding pulses of 10 [ms] or less
Excluding pulses of 2 [ms] or less
10.3 Power Supply Sequence
The drive shall operate normally with the power supply sequence specified in Fig.10.3-1 and Table 10.3-1 .
(Fig. 10.3-1) Power supply sequence
(Table 10.3-1) Power supply sequence specifications
Item
T1, T2, T3, T4
Specifications
50 [msec] Max.
18 / 26
HARDWARE SPECIFICATION, DV-518GSC-xxx,Rev. A
10.4 Power Interface Connector
(a) Number of [poles]
(b) Protection method for mis-insertion
(c) Connector terminal diagram
(d) Connector location
(e) Pin assignment
: 15 [pins]
: by the shape of the connector housing
: Refer to Fig.10.4-1
: Refer to Fig.10.4-1
: Refer to Table 10.4-1
(Fig. 10.4-1) External view of the rear
Name
P1
P2
P3
P4
P5
P6
P7
P8
P9
P10
(Table 10.4-1) Power interface connector pin assignment
P11
P12
P13
P14
P15
Type
Gnd
V
5
V
5
V
5
Gnd
V
33
V
33
V
33
Gnd
Gnd
Reserved
Gnd
V
12
V
12
V
12
Description
3.3 [V] Power
3.3 [V] Power
3.3 [V] Power
1 st mate
2 nd
mate
2 nd
mate
5 [V] Power, pre-charge, 2 nd mate
5 [V] Power
5 [V] Power
2 nd
mate
1. The pin corresponding to P11 in the backplane receptacle connector is also reserved.
2. The corresponding pin to be mated with P11 in the power cable receptacle connector shall always be grounded.
1 st
mate
12 [V] power, pre-charge, 2 nd
mate
12 [V] power
12 [V] power
19 / 26
HARDWARE SPECIFICATION, DV-518GSC-xxx,Rev. A
11. SATA HARDWARE INTERFACE
11.1 Applicable Standard
ANSI
SFFC
: ATA-8 Compliant
: SFF-8090i V7 Compliant
11.2 Electrical Characteristics
Refer to Serial ATA Revision 2.6.
11.3 Signal Interface Connector
(1) Signal interface connector
(a) Connector pin diagram
(b) Connector layout
(c) Connector pin-assignment table
: Refer to Fig.10.4-1
: Refer to Fig.10.4-1
: Refer to Table 11.3-1
(Table 11.3-1) Signal interface pin-assignment table
Name
S1
S2
S3
S4
S5
S6
S7
Type
Gnd
A+
A-
Gnd
B-
B+
Gnd
2 nd mate
Description
Differential signal pair A from Phy
2 nd mate
Differential signal pair B from Phy
2 nd mate
20 / 26
HARDWARE SPECIFICATION, DV-518GSC-xxx,Rev. A
12. REQUESTS RELATING TO THE FCC RULE PART (15) AND SAFETY LASER
PRODUCTS
12.1 FCC Rule Part (15)
When selling this unit directly to an end user, print the following text in the instruction manual or enclose the separate sheet on which the following text is printed with the instruction manual.
Model Number
Trade Name
Responsible party
: DV-518GSC-xxx
: TEAC
Declaration of Conformity
: TEAC AMERICA, INC.
Address : 1834 Gage Road, Montebello, California, U.S.A.
Telephone Number : 1-213-726-0303
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions : (1)This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
TO THE USER
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against interference in a residential areas. This device generates and uses radio frequency energy and if not installed and used in accordance with the instructions, it may cause interference to radio or TV reception. If this unit does cause interference with TV or radio reception you can try to correct the interference by one more of the following measures: a) Reorient or relocate the receiving antenna. b) Increase the separation between the equipment and receiver. c) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. d) Consult the dealer or an experienced radio/TV technician for help.
CAUTION:
Changes or modifications to this equipment not expressly approved TEAC CORPORATION for compliance could void the user’s authority to operate this equipment.
21 / 26
HARDWARE SPECIFICATION, DV-518GSC-xxx,Rev. A
12.2 Safety of Laser Products
When selling this unit or a system with this unit to an end user, print the following text in the instruction manual or enclose the separate sheet on which the following text is printed with the instruction manual.
This product has been designed and manufactured according to FDA regulations "title 21.
CFR. chapter1, subchapter J. based on the radiation Control for Health and Safety Act of
1968", and is classified as a class 1 laser product. There is no hazardous invisible laser radiation during operation because invisible laser radiation emitted inside of this product is completely confined in the protective housings. the label required in this regulation is shown bellow.
CAUTION
Use of controls or adjustments or performance of procedures other than those specified here in may result in hazardous radiation exposure.
Type
Manufacturer
Laser output
Wavelength
Optical pickup
: LO-DRH10
: LOOK-TEC
: DVD
: CD
: DVD
: CD
: 0.23 [mW]
: 0.20 [mW]
: 660 [nm]
: 790 [nm]
12.3 Attachment Location
Location of TEAC Nameplate on the Bottom cover is shown in Fig.12.3-1 .
(Fig. 12.3-1) Nameplate Location on the Bottom Cover
22 / 26
13. ROHS COMPLIANCE
The drive complies with European directive “2011/65/EU”.
EU Importer name and address
TEAC EUROPE GmbH
Bahnstrasse12, 65205 Wiesbaden - Erbenheim, Germany
HARDWARE SPECIFICATION, DV-518GSC-xxx,Rev. A
23 / 26
HARDWARE SPECIFICATION, DV-518GSC-xxx,Rev. A
14. LABEL USED
(Fig. 14-1) Nameplate
TEAC Part number
Numerals converted from barcode
Barcode
Month manufactured
Model name
(Fig. 14-2) Serial label
TEAC Model name
TEAC Part number
(10-digits number + L)
Serial number
(1st S/No. + Hyphen + Last S/No. of carton)
Barcode (Code39)
Part No. (10-digits) + Start S/No. (7-digits) +20 (fixed)
Manufacturer
In-house description (for factory)
(Fig. 14-3) Carton label for 20 in 1
24 / 26
HARDWARE SPECIFICATION, DV-518GSC-xxx,Rev. A
15. PACKAGING
(Table 15-1) Aggregate package for 20 in 1
Item
Outline dimensions of carton
Packed quantity in one package
Gross Weight for one package
① Cushion PMP in a Carton
② PE Bag, Drive
③ Products
④ Partition
⑤ Carton, Bulk
Specification
L [mm]
560
20 [sets]
Typical 13.06 [kgs]
W [mm]
400
2 [EA]
20 [Pcs]
20 [sets]
4 [EA]
1 [EA]
H [mm]
213
(Fig. 15-1) Aggregate package for 20 in 1
25 / 26
HARDWARE SPECIFICATION, DV-518GSC-xxx,Rev. A
(Fig. 15-2) Label attaching position on the packing box for 20 in 1
26 / 26
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement