Simrad GO XSE Getting Started
Simrad GO XSE is a fully integrated navigation system that combines charts, radar, sonar, and autopilot control into one easy-to-use display. With its simple and intuitive interface, you can quickly access all of the information you need to navigate safely and confidently. Whether you're a seasoned pro or a first-time boater, the GO XSE has everything you need to make your time on the water more enjoyable.
Hirdetés
Hirdetés
GO XSE
Getting Started
ENGLISH
www.simrad-yachting.com
Contents
6
Introduction
6
7
9
Basic operation
9
9
10
10
11
11
Creating a Man Overboard waypoint
13 Charts
13
14
14
14
15
Positioning the vessel on the chart panel
16
Displaying information about chart items
17
17
18 Waypoints, Routes, and Tracks
18
19
20
21 Navigating
21
22
22
23 TripIntel
23
24 Autopilot
24
Safe operation with the autopilot
Contents | GO XSE Getting Started 3
4
24
24
Switching from automatic mode to manual steering
25
Autopilot indication on the pages
26
27 Radar
27
28
28
29
29
30 Echosounder
30
31
31
32 StructureScan
32
33
34 ForwardScan
34
35
35
37 Instrument panels
37
38 Wireless connection
38
Connect and disconnect from a wireless hotspot
39 Audio
39
40
40
41 Alarms
41
Contents | GO XSE Getting Started
41
42 Tools
42
42
42
42
42
43
43
43
43
43
Contents | GO XSE Getting Started 5
1
Introduction
This manual provides an overview of the product and its features.
For more detailed information about the features, functions and options, refer to the Operator manual. You can access the Operator
manual from the Files option in the Tools panel, refer to "Files" on page 43.
The Home page
The Home page is accessed from any operation by selecting the
Home button in the upper left corner of a panel.
6
1 Tools
Select a button to access dialogs used for carrying out a task, or for browsing stored information.
2 Applications
Select a button to display the application as a full page panel. Press and hold a button to display pre-configured split page options for the application.
3 Close button
Select to exit the Home page and return to the previous active page.
Introduction | GO XSE Getting Started
4 Favorites
Select a button to display the panel combination.
Press and hold a favorite button to enter edit mode for the
Favorites panel.
5 Man Over Board (MOB) button
Select to save a Man Over Board (MOB) waypoint at the current vessel position.
Application pages
Each application connected to the system is presented on panels.
The application can be presented as a full page, or in combination with other panels in a multiple panel page.
All application pages are accessed from the Home page.
1 Application panel
2 Instrument bar
Navigation and sensor information. The bar can be turned off and it can be configured by the user.
3 System controls dialog
Quick access to basic system settings.
Display the dialog by a short press on the Power key or by swiping down from top of the screen.
4 Status bar
5 Dialog
Information to or input from the user.
Introduction | GO XSE Getting Started 7
6 Alarm message
Displayed if dangerous situations or system faults occur.
7 Menu
Panel specific menu.
Display the menu by selecting the MENU panel button.
Pre-configured split pages
Each full screen application has several pre-configured split pages, featuring the selected application combined with each of the other panels.
Ú Note: The number of pre-configured split pages cannot be changed, and the pages cannot be customized or deleted.
Access a pre-configured split page by pressing and holding the main panel button.
8 Introduction | GO XSE Getting Started
2
Basic operation
System Controls dialog
The System Controls dialog provides quick access to basic system settings. You display the dialog by making a short press on the
Power key or by swiping down from the top of the screen.
The icons displayed on the dialog can vary. For example, the adjust splits option is only available if you are viewing a split page when you open the System Controls dialog.
Activating functions
Select the icon of the function you want to set or toggle on or off.
For those functions that toggle on and off, a highlighted icon indicates the function is activated, as shown in the Instrument bar icon above.
Turning the system on and off
You turn the system on and off by pressing and holding the Power key. You can also turn the unit off from the System Controls dialog.
If the Power key is released before the shut-down is completed, the power off process is cancelled.
Basic operation | GO XSE Getting Started 9
Selecting pages and panels
Selecting a page
• Select a full page panel by selecting the relevant application button on the Home page
• Select a favorite page by selecting the relevant favorite button
• Select a predefined split panel by pressing and holding the relevant application icon
Select active panel
In a multiple panel page, only one panel can be active at a time. The active panel is outlined with a border.
You can only access the page menu of an active panel.
You activate a panel by tapping it.
Adjusting panel size
You can change the panel size for an active split page. The panel size can be adjusted for both favorite pages and for predefined split pages.
1.
Activate the System Controls dialog
2.
Select the adjust splits option in the dialog
3.
Adjust the panel size by dragging the adjustment icon
4.
Confirm your changes by tapping one of the panels or selecting the save option in the menu.
10
The changes are saved to the active favorite or split page.
Basic operation | GO XSE Getting Started
Adding new favorite pages
1.
Select the New icon in the favorite panel on the Home page to open the page editor dialog
2.
Drag and drop page icons to set up a new page
Ú Note: 5" unit favorite pages can have a maximum of 2 applications.
3.
Change the panel arrangement (only possible for 2 or 3 panels), if required
4.
Save the page layout.
The system displays the new favorite page, and the new page is included in the list of favorite pages on the Home page.
Creating a Man Overboard waypoint
If an emergency situation should occur, you can create a Man
Overboard (MOB) waypoint at the vessel’s current position by selecting the MOB button on the Home page.
When you activate the MOB function the following actions are automatically performed:
• a MOB waypoint is created at the vessel’s position
• the display switches to a zoomed chart panel, centered on the vessel's position
Basic operation | GO XSE Getting Started 11
• the system displays navigation information back to the MOB waypoint
Multiple MOB waypoints are saved by repeatedly pressing the MOB buttons. The vessel continues to show navigation information to the initial MOB waypoint. Navigation to subsequent MOB waypoints needs to be done manually.
Delete a MOB waypoint
1.
Select the MOB waypoint to activate it
2.
Select the MOB waypoint's pop-up to display the MOB waypoint dialog
3.
Select the delete option in the dialog.
A MOB waypoint can also be deleted from the menu when it is activated.
12 Basic operation | GO XSE Getting Started
3
Charts
The chart function displays your vessel’s position relative to land and other chart objects. On the chart panel you can plan and navigate routes, place waypoints, and display AIS targets.
The Chart panel
1 Waypoint*
2 Vessel with extension line (extension line is optional)
3 Route*
4 North indicator
5 Grid lines*
6 Range rings*
7 Track*
8 Chart range scale
9 Range rings interval (only displayed when Range rings are turned on)
* Optional chart items. You turn the optional chart items on/off individually from the Chart settings dialog.
Charts | GO XSE Getting Started 13
14
Showing dual chart types
If you have different chart types available - embedded or in the card slot - you can show two different chart types simultaneously on a page with two chart panels.
You can select a dual chart panel by pressing and holding the Chart application button on the Home page, or by creating a favorite page with two chart panels.
Panning the chart
You can move the chart in any direction by dragging your finger on the screen.
Select the Clear cursor menu option to remove the cursor and cursor window from the panel. This also centers the chart to the vessel position.
Using the cursor on the panel
The cursor can be used to measure a distance, to mark a position, and to select items.
By default, the cursor is not shown on the panel.
Position the cursor by tapping the desired location on the screen.
When the cursor is active, the cursor position window is displayed.
To remove the cursor and cursor elements from the panel, select the Clear cursor option.
GoTo cursor
You can navigate to a selected position on the image by positioning the cursor on the panel, then using the Goto Cursor option in the menu.
The Cursor assist function
The cursor assist function allows for fine tuning and precision placement of the cursor without covering details with your finger.
Press and hold your finger on the screen to switch the cursor symbol to a selection circle, appearing above your finger.
Without removing your finger from the screen, drag the selection circle over the desired item to display item information.
Charts | GO XSE Getting Started
When you remove your finger from the screen the cursor reverts to normal cursor operation.
Measuring distance
The cursor can be used to measure the distance between your vessel and a selected position, or between 2 points on the chart panel.
1.
Position the cursor on the point from where you want to measure the distance. Start the measure function from the menu
- The measuring icons appear with a line drawn from the vessel center to the cursor position, and the distance is listed in the cursor information window.
2.
You can reposition the measuring points by dragging either icon as long as the measuring function is active
Ú Note: The bearing is always measured from the grey icon to the blue icon.
You can also start the measuring function without an active cursor.
Both measuring icons are then initially located at the vessel position.
The grey icon follows the vessel as the vessel moves, while the blue icon remains at the position given when you activated the function.
You terminate the measuring function by selecting the Finish
measuring menu option.
Positioning the vessel on the chart panel
Charts | GO XSE Getting Started 15
Chart orientation
Several options are available for how the chart is rotated in the panel. The chart orientation symbol in the panel’s upper right corner indicates the north direction.
16
North up Heading up Course up
North up
Displays the chart with north upward.
Heading up
Displays the chart with the vessel’s heading directed upward.
Heading information is received from a compass. If heading is not available, then the COG from the GPS is used.
Course up
Displays the chart with the direction the vessel is ACTUALLY traveling directed upward, which in some cases is not the direction the vessel is headed.
Look ahead
Moves the vessel icon closer to the bottom of the screen so that you can maximize your view ahead.
Displaying information about chart items
When you select a chart item, a waypoint, a route, or a target, basic information for the selected item is displayed. Select the chart item's pop-up to display all available information for that item. You can also activate the detailed information dialog from the menu.
Ú Note: If you are viewing applicable C-MAP charts on your system, you can select marine objects to display information about services and available multimedia (photos) associated with the location or object.
Charts | GO XSE Getting Started
Ú Note: Pop-up information has to be enabled in chart settings to see basic item information.
Find objects on chart panels
You can search for other vessels or various chart items from a chart panel.
Activate the cursor on the panel to search from the cursor position.
If the cursor is not active, the system searches for items from the vessel's position.
Ú Note: You must have a SIRIUS data package subscription to search for fueling stations and an AIS receiver connected to search for vessels. SIRIUS is not available on 5" and 7" units.
3D charts
The 3D option provides a three dimensional graphical view of land and sea contours.
Ú Note: All chart types work in 3D mode, but without 3D cartography for the appropriate area the chart appears flat.
When 3D chart option is selected, the Pan and the Rotate icons appear on the right side of the chart panel.
Charts | GO XSE Getting Started 17
4
Waypoints, Routes, and Tracks
Waypoints
A waypoint is a user generated mark positioned on a chart, or on the Echosounder image. Each waypoint has an exact position with latitude and longitude coordinates. A waypoint positioned on the
Echosounder image has a depth value, in addition to position information. A waypoint is used to mark a position you later may want to return to. Two or more waypoints can also be combined to create a route.
Saving waypoints
You can save a waypoint at a selected location by positioning the cursor on the panel, and then selecting the new waypoint option in the menu.
18
In the Chart and Nav panels, you can save a waypoint at the vessel position, when the cursor is not active, by selecting the new waypoint option in the menu.
Moving a waypoint
1.
Select the waypoint you want to move. The waypoint icon expands to indicate that it is active.
2.
Activate the menu and select the waypoint in the menu
3.
Select the move option
4.
Select the new waypoint position
5.
Select Finish in the menu.
The waypoint is now automatically saved at the new position.
Waypoints, Routes, and Tracks | GO XSE Getting Started
Edit a waypoint
You can edit all information about a waypoint from the Edit
Waypoint dialog.
This dialog is activated by selecting the waypoint's pop-up, or from the menu when the waypoint is activated.
The dialog can also be accessed from the Waypoints tool on the
Home page.
Routes
A route consists of a series of routepoints entered in the order that you want to navigate them.
When you select a route on the chart panel it turns green, and the route name is displayed.
The system includes support for Navionics Autorouting and C-MAP
Easy Routing. This feature automatically suggests routepoints between the first and last routepoint of a route, or between selected routepoints in a complex route. You can use the feature when you create a new route, or you can use it to edit already saved routes.
Creating a new route on the chart panel
1.
Activate the cursor on the chart panel
2.
Select the new route option from the menu
3.
Position the first waypoint on the chart panel
4.
Continue positioning new routepoints on the chart panel until the route is completed
5.
Save the route by selecting the save option in the menu.
Waypoints, Routes, and Tracks | GO XSE Getting Started 19
Edit a route from the chart panel
1.
Select the route to make it active.
2.
Select the route edit option in the menu.
3.
Position the new routepoint on the chart panel:
- If you set the new routepoint on a leg, a new point is added between existing routepoints.
- If you set the new routepoint outside the route, the new routepoint is added after the last point in the route.
4.
Drag a routepoint to move it to a new position.
5.
Save the route by selecting the save option in the menu.
Ú Note: The menu changes depending on the selected edit option. All edits are confirmed or cancelled from the menu.
Tracks
Tracks are a graphical presentation of the historical path of the vessel, allowing you to retrace where you have travelled. Tracks can be converted to routes from the Edit dialog.
From the factory, the system is set to automatically track and draw the vessel's movement on the chart panel. The system continues to record the Tracks until the length reaches the maximum points, and then automatically begins overwriting the oldest points.
The automatic tracking function can be turned off from the Tracks dialog.
Creating new Tracks
You can start a new track from the Tracks dialog, activated by using the Tracks tool on the Home page.
20 Waypoints, Routes, and Tracks | GO XSE Getting Started
5
Navigating
The navigation function included in the system allows you to navigate to the cursor position, to a waypoint, or along a predefined route.
If autopilot functionality is included in your system, the autopilot can be set to automatically navigate the vessel.
For information about positioning waypoints and creating routes,
refer to "Waypoints, Routes, and Tracks" on page 18.
Navigation panels
The Nav panels can be used to display information when you are navigating.
The Nav panel
The Nav panel is activated from the Home page, either as a full page panel or as part of a multiple panel page.
1 Data fields
2 Route information
3 Vessel heading
Navigating | GO XSE Getting Started 21
4 Bearing to next routepoint
5 Bearing line with allowed off course limit
When travelling on a route the bearing line shows the intended course from one waypoint towards the next.
When navigating towards a waypoint (cursor position, MOB or an entered lat/lon position), the bearing line shows the intended course from the point at which navigation was started towards the waypoint.
6 Vessel symbol
Indicates distance and bearing relative to the intended course. If the XTE (Cross Track Error) exceeds the defined XTE limit, this is indicated with a red arrow including the distance from the track line.
Navigate to cursor position
You can start navigating to a cursor position on any chart, or
Echosounder panel.
Position the cursor at the selected destination on the panel, and then select the Goto Cursor option in the menu.
Ú Note: The Goto Cursor menu option is not available if you are already navigating.
Navigate a route
You can start navigating a route from the chart panel or from the
Route dialog.
When route navigation is started, the menu expands and shows options for canceling the navigation, for skipping a waypoint, and for restarting the route from current vessel position.
22 Navigating | GO XSE Getting Started
6
TripIntel
TripIntel lets you store and recall information on trips. You can use the information to make informed decisions prior to commencing a trip, or when a trip is underway.
Ú Note: For best results, it is recommended to run software version 2.4.0 or newer in your EP-85R Storage Device.
Select the TripIntel button on the Tool panel to display the TripIntel page.
Current trip statistics
The Information tab on the TripIntel page shows current trip statistics:
• Distance traveled
• Time traveled
• Average speed
• Maximum speed
• Fuel economy
• Fuel used
TripIntel | GO XSE Getting Started 23
7
Autopilot
If a compatible autopilot computer is connected to the system, autopilot functionality is available in the system.
The system does not allow for more than one autopilot computer on the network.
The display unit automatically detects the autopilot computer available on the network and presents settings, configuration and user options for the connected computer.
For details about installing and configuring an autopilot computer, refer to the separate manuals that come with the autopilot computer.
Safe operation with the autopilot
Warning: An autopilot is a useful navigational aid, but DOES NOT replace a human navigator.
Warning: A physical standby key should be available for the autopilot.
Activating the autopilot
You activate the autopilot from any panel by selecting the autopilot tile in the Instrument bar, followed by selecting a mode in the
Autopilot Controller.
Switching from automatic mode to manual steering
You switch the autopilot to STBY mode from any automatic operation mode from the autopilot pop-up or using a physical standby key.
24 Autopilot | GO XSE Getting Started
Autopilot indication on the pages
1 Autopilot indication in Status bar
2 Autopilot pop-up
3 Autopilot tile in Instrument bar
Autopilot mode indication in the Status bar
The Status bar shows autopilot information as long as an autopilot computer is connected to the network.
Icons are included if the autopilot is passive or locked by another autopilot control unit.
Autopilot pop up
You control the autopilot from the autopilot pop-up. The pop-up has a fixed position on the page, and it is available for all pages except when an Autopilot panel is active.
As long as the autopilot pop-up is active, you cannot operate the background panel or its menu. You remove the pop-up from a page by selecting the X in the upper right corner. You turn it on again by selecting the autopilot tile in the instrument bar.
The following pop-ups are available:
Autopilot | GO XSE Getting Started 25
Autopilot controller Mode selection Turn pattern selection
Autopilot tile in Instrument bar
You can select to show the autopilot tile in the Instrument bar.
If the autopilot pop-up is turned off you can turn it on by selecting the tile in the Instrument bar.
The Autopilot panel
The autopilot panel is used to display navigation data. It can be shown as a full screen panel, or in a multi-panel page.
The number of data fields included in the autopilot panel is dependent on available panel size.
26 Autopilot | GO XSE Getting Started
8
Radar
Radar is not available on the 5" and 7" units.
The radar panel can be set up as a full screen view or combined with other panels.
Using the chart menu, the radar image can also be displayed as an overlay on a chart panel.
Ú Note: Radar overlay requires data from a heading sensor or compass to ensure proper orientation with the chart.
The radar panel
1 Range
2 Orientation
3 Motion
4 Compass*
5 Heading line*
6 Rotary controls
7 Range rings*
Radar | GO XSE Getting Started 27
8 Range markers*
9 Data bar
* Optional radar symbology.
Radar symbology can be turned ON/OFF collectively from the Radar
menu, or individually as described in "Radar settings panel" on page 29.
Radar menu options
Use the Radar menu to set up EBL/VRM, guard zones, set the radar in standby and access the Adjust, Advanced and View options.
• EBL/VRM - The electronic bearing line (EBL) and variable range marker (VRM) allows quick measurements of range and bearing to vessels and landmasses within radar range.
• Guard zones - A guard zone is an area (either circular or a sector) that you can define on the radar image. When activated, an alarm alerts you when a radar target enters or exits the zone.
• Standby - The power to the radar scanner is on, but the radar is not transmitting.
Adjust the radar image
From the radar menu use the Adjust options to set the mode, gain,
Sea clutter and Rain clutter. By adjusting these settings, you may be able to improve the radar image by adjusting the radar sensitivity, and by filtering out the random echoes from sea and weather conditions.
28 Radar | GO XSE Getting Started
View and Advanced options
Use the menu View and Advanced options to refine the radar image to meet your needs.
View menu
Radar settings
Advanced menu
Radar | GO XSE Getting Started 29
9
Echosounder
The Echosounder function provides a view of the water and bottom beneath your vessel, allowing you to detect fish and examine the structure of the sea floor.
The Echosounder image
1 Depth
2 Temperature
3 Frequency and Zoom scale
4 Bottom
5 Zoom buttons
6 Depth range scale
7 Instrument panel
8 Zoom column
9 Fish arches
30 Echosounder | GO XSE Getting Started
Viewing Echosounder history
You can view echosounder history by panning the image. To resume normal scrolling, select the Clear cursor menu option.
Setting up the image
Use the Echosounder menu options to set up the image. When the cursor is active, some options on the Echosounder menu are replaced with cursor mode features. Select Clear cursor to return to the normal Echosounder menu.
Main menu Advanced menu View menu
Ú Note: The A-scope and Zoom bars options are not available on the 5" units.
Echosounder | GO XSE Getting Started 31
10
StructureScan
StructureScan HD uses high frequencies to provide a high resolution, picture-like image of the seabed.
The StructureScan image
The view
The StructureScan panel can be set up as a DownScan image, or showing left/right side scanning.
The DownScan image can also be added as an overlay to the traditional Echosounder image.
32
1 Depth
2 Temperature
3 Frequency
4 Bottom
StructureScan | GO XSE Getting Started
5 Zoom (downscan) / Range (sidescan) icons
6 Range scale
Setting up the image
Use the StructureScan menu options to set up the image. When the cursor is active, some options on the StructureScan menu are replaced with cursor mode features. Select Clear cursor to return to the normal StructureScan menu.
Main menu Advanced menu View menu
StructureScan | GO XSE Getting Started 33
11
ForwardScan
ForwardScan sonar is a navigational aid that helps you monitor the underwater environment in front of your vessel while carrying out slow speed maneuvers.
To use the ForwardScan feature you must have a ForwardScan transducer mounted on your vessel. For installation instructions, refer to the ForwardScan transducer installation manual.
Ú Note: Do not rely on this equipment as your principle source of navigation or hazard detection.
Ú Note: Do not use this equipment to gauge depth or other conditions for swimming or diving.
The ForwardScan image
34
1 Transducer location shown as the origin on the page
2 Depth range scale and vessel position
3 Forward range scale
4 Point data
ForwardScan | GO XSE Getting Started
5 Bottom
6 Depth history
Setting up the image
Use the ForwardScan menu options to set up the image. When the cursor is active, some options on the ForwardScan menu are replaced with cursor mode features. Select Clear cursor to return to the normal ForwardScan menu.
Main menu View menu
Heading extension
You can use the heading extension to monitor ForwardScan on the chart panel. Heading extension colors are based on the
ForwardScan alarm values.
ForwardScan | GO XSE Getting Started 35
ForwardScan extension
1 Red - Critical
2 Yellow - Warning
3 Green - Safe
Select ForwardScan in the Chart Settings dialog to view the
ForwardScan heading extension on the chart panel.
36 ForwardScan | GO XSE Getting Started
12
Instrument panels
The Instruments panels consist of multiple gauges - analog, digital and bar - that can be customized to display selected data. The
Instruments panel displays data on dashboards, and you can define up to ten dashboards within the Instruments panel.
Ú Note: To include fuel/engine information, engine and tank information has to be configured from the Settings panel.
Dashboards
A set of dashboard styles are predefined to display vessel, navigation, and angler information.
You switch between the panel’s dashboards by selecting the left and right arrow buttons on the panel. You can also select the dashboard from the menu.
Vessel dashboard Navigation dashboard Angler dashboard
Ú Note: Additional dashboards can be activated from the menu if other systems (e.g. CZone) are present on the network.
Instrument panels | GO XSE Getting Started 37
13
Wireless connection
GoFree wireless connectivity gives you the ability to:
• Use a wireless device to remotely view (smartphone and tablet) and control the system (tablet only).
• Access the GoFree Shop.
• Upload your Sonar logs to create custom maps at Insight
Genesis.
• Download software updates
• Connect to third party applications
The unit includes Built-in wireless functionality for connecting to the internet and wireless devices such as smartphones and tablets.
Ú Note: Maps, charts, software updates, and other data files can be large. Your insternet service provider may charge you based on the amount of data you transfer. If you are unsure, contact your service provider to confirm rates and restrictions.
Connect and disconnect from a wireless hotspot
To connect to a wireless hotspot, select the Wireless option in the
System Controls dialog and then select Not Connected. This opens the Wireless Devices dialog. Use this dialog to select the desired hotspot, enter the login information and then select Connect.
Connecting to a wireless hotspot changes the wireless mode to
Client mode. In this mode, you can access the GoFree Shop.
To disconnect from a wireless hotspot, select the Wireless option in the System Controls dialog, then select Connected hotspot_name, and then Disconnect. This changes the wireless mode to Access point
mode. In this mode, you can connect a wireless device so that Apps such as GoFree Controller & Viewer can access the vessel's navigation information.
38 Wireless connection | GO XSE Getting Started
14
Audio
If a SonicHub server, a FUSION marine entertainment system, or
NMEA 2000 audio system is connected to the NMEA 2000 network, you can use the GO XSE to control and customize the audio system on your vessel.
You can connect a SiriusXM radio/tuner to your FUSION server to receive SiriusXM radio on your system. The SiriusXM channels available vary depending on your selected subscription package.
SiriusXM radio is only available in certain locations. For more information refer to www.siriusXM.com. SiriusXM audio is not available on 5" and 7" units.
Before you can start using your audio equipment, it must be installed according to the GO XSE Installation manual and to the documentation included with the audio device.
Enabling audio
A compatible audio device connected to the NMEA 2000 network should automatically be identified by the system. If not, enable the feature from the Advanced Settings dialog.
Audio | GO XSE Getting Started 39
The Audio panel
You activate the audio panel by activating the audio tile in the
Instrument bar.
The control buttons, tools and options vary from one audio source to another as described later in this chapter.
40
1 Audio source
2 Audio control buttons
3 Audio tile
4 Audio tools
Operating the audio system
1.
Select the Audio tile in the Instrument bar to activate the Audio overlay.
2.
Select the options icon and then select the audio server.
3.
Select the source icon and then select the audio source.
- Number of sources depends on the active audio server.
4.
Use the panel buttons to control your audio system.
For available options, refer to the documentation following your audio equipment.
Audio | GO XSE Getting Started
15
Alarms
Alarm system
The system continuously checks for dangerous situations and system faults while the system is running. When an alarm situation occurs, an alarm message pops up on the screen.
If you have enabled the siren, the alarm message is followed by an audible alarm, and the switch for external alarm becomes active.
The alarm is recorded in the alarm listing so that you can see the details and take the appropriate corrective action.
Alarms dialog
All alarms are setup in the Alarms Settings dialog.
Alarms | GO XSE Getting Started 41
42
16
Tools
By default, the Tools panel includes icons used for accessing options and tools that are not specific to any panel.
When external equipment is integrated to the unit, new icons might be added to the Tools panel. These icons are used for accessing the external equipment's features.
Waypoints/routes/tracks
List of waypoints, routes, and tracks with details.
Select the waypoint, route, or track you wish to edit or delete.
Tides
Displays tide information for the tide station nearest to your vessel.
Select the arrow panel buttons to change the date, or select the date field to access the calendar function.
Available tide stations can be selected from the menu.
Alarms
Active alarms
List of active alarms.
Alarm history
List of all alarms with time stamp.
Alarm settings
List of all available alarm options in the system, with current settings.
Settings
Provides access to application and system settings.
Vessels
Status listing
List of all AIS and DSC vessels with available information.
Tools | GO XSE Getting Started
Message listing
List of all messages received from other AIS vessels with time stamp.
Sun, Moon
Displays sunrise, sunset, moonrise and moonset for a position based on entered date and the position’s latitude/longitude.
TripIntel
Provides trip management functionality and trip information. For more information, refer to the Operator manual
Files
File management system for Files, Waypoints, Routes, Trails, and
Settings.
To view files, select a file in the Files panel and then the view file option in the Details dialog. You can copy screen captures and logs to a card in the card reader.
You can also export System Settings, Waypoints, Routes, and Trails to a memory card.
To view recorded sonar logs, use the view sonar log option in the
Sonar settings dialog.
Find
Search function for chart items (waypoints, routes, tracks, etc.).
GoFree Shop
Ú Note: The built-in wireless functionality must be connected to an external wireless hotspot in order to access the GoFree Shop.
Refer to "Connect and disconnect from a wireless hotspot" on page 38.
Opens the GoFree Shop web site. At the GoFree Shop you can browse, purchase, and download compatible charts for your system.
You can also upload your Echosounder logs to be shared on Social
Map charts. When you log on, the system automatically gives you a notification if a new software version is available for your system. If an update is available, you can download it to a card slot or defer the download until later.
Tools | GO XSE Getting Started 43
0980
Letöltés
A nyilvános link frissítve
A csevegés nyilvános linkje frissítve lett. You may view and manage your chat links after registration here.
Dokumentum nyilvános linkje
Hirdetés