Schneider Electric TSX 57 PCX 57, TSX DM 57 40E, TSX P ACC 01, TSX SAY 100, TSX SCY 21601, TSX ETY 110, TSX ETY 410, TSX ETY 510, TSX SCP 111, TSX SCP 112, TSX SCP 114, TSX FPP 20, TSX FPP 10, TSX MBP 100, TSX MDM 10 Installation manual

Premium PLCs
TSX 57/PCX 57
Communication
Network and bus interfaces
Installation manual Volume 4
3500259500
TSX DM 57 40E eng
2
Related Documentation
Related Documentation
At a Glance
TSX DM 57 40E 09.2000
This documentation is made up of 5 Volumes:
l Volume 1
l Racks/Supplies/Processors
l Implementation/Diagnostics/Maintenance
l Standards and operating conditions
l Process supply
l Volume 2
l Discrete interfaces
l Safety
l Volume 3
l Counting
l Movement commands
l Volume 4
l Communication
l Network and bus interfaces
l Volume 5
l Analog
l Weighing
3
Related Documentation
4
TSX DM 57 40E 09.2000
Table of Contents
About the book . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Part I Terminal Port Communication . . . . . . . . . . . . . . . . . . . . 15
At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Chapter 1
1.1
1.2
1.3
Chapter 2
Terminal Port. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Introduction to the terminal port. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Introduction to the terminal port. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Communication with a programming/adjustment terminal . . . . . . . . . . . . . . . . .
Communicating with a man-machine interface console . . . . . . . . . . . . . . . . . . .
UNI-TELWAY master/slave communication . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Character string communication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Programming/Adjustment terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Man-machine interface console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Programming/adjustment terminal and man-machine interface console . . . . . .
Modem on terminal port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Master UNI-TELWAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Slave UNI-TELWAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Inter-PLC UNI-TELWAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Inter-device UNI-TELWAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Master PLC type TSX model 40 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Character string. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Summary table of terminal port connections . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Appendices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Characteristics of the terminal port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Terminal port connector pin configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
17
18
18
19
21
23
24
25
26
26
27
28
30
31
32
34
35
36
38
39
40
43
45
45
46
48
TSX P ACC 01 device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
5
2.1
2.2
2.3
At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Standard functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
External appearance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Hardware installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Dimensions and mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Internal view. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Connection to UNI-TELWAY Buses. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Connecting to Premium and Atrium PLCs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Switch configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
TSX P ACC 01 connector pin configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Example of topologies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Connecting devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
UNI-TELWAY master mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
UNI-TELWAY slave mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Connection between two PLCs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Part II Processor-integrated master FIPIO communication . . . 67
At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Chapter 3
Processor-integrated master FIPIO communication . . . . . . . 69
At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Review of the FIPIO bus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Integrated FIPIO link on Premium/Atrium processors . . . . . . . . . . . . . . . . . . . . . 72
Examples of architecture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Part III AS-i bus interface: TSX SAY 100 module . . . . . . . . . . . . 75
At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Chapter 4
4.1
4.2
6
AS-i bus interface module: TSX SAY 100 . . . . . . . . . . . . . . . . 77
At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Review of the AS-i bus. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Review of the AS-i bus. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Overview of AS-i products from the Schneider catalog . . . . . . . . . . . . . . . . . . . . 80
Introduction to the main constituent elements . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Example of AS-i bus topology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Main characteristics of the AS-i bus. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Description of the TSX SAY 100 module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Physical presentation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Mounting/installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
4.3
4.4
4.5
4.6
Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Displaying module states . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
Specific display panels on the TSX SAY 100 module . . . . . . . . . . . . . . . . . . . . . 96
Technical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
Personnel safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Input/output object addressing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
Addressing input/output objects . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
AS-i Bus diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
Introduction to AS-i Bus diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
Moving between the different display modes . . . . . . . . . . . . . . . . . . . . . . . . . . 104
Display of slaves on the AS-i bus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Viewing the state of input/output bits for each slave . . . . . . . . . . . . . . . . . . . . . 106
Operating modes of the TSX SAY 100 module. . . . . . . . . . . . . . . . . . . . . . . . . 108
Operating modes of the TSX SAY 100 module. . . . . . . . . . . . . . . . . . . . . . . . . 108
Precautions of use. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
24 V auxiliary supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
Multiple addressing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
Part IV Communication: module TSX SCY 21601 and
PCMCIA cards. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
Chapter 5
At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
General communication architecture. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
Operating standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
Chapter 6
6.1
6.2
6.3
6.4
6.5
6.6
6.7
Installing the TSX SCY 21601 module . . . . . . . . . . . . . . . . . . 119
At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Characteristics of the integrated channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Characteristics of the integrated channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Compatibility of reception channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Compatibility of the reception channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Visual diagnostics of the module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Visual diagnostics of the module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
119
120
120
121
121
123
123
124
124
125
125
127
127
128
128
7
6.8
Chapter 7
7.1
7.2
7.3
7.4
7.5
7.6
7.7
7.8
8
Connecting the built-in channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131
Connection to UNI-TELWAY bus. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132
Reminder on adapting the line distributed over RS 485 . . . . . . . . . . . . . . . . . . 134
Example of UNI-TELWAY architecture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136
Connecting to the Jbus/Modbus field bus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
Reminder on single line polarization in RS 485 . . . . . . . . . . . . . . . . . . . . . . . . . 138
Example of Modbus architecture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140
Connecting the TSX SCA 50 device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141
Connection in Character Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142
Consumption of the TSX SCY 21601 module . . . . . . . . . . . . . . . . . . . . . . . . . . 143
Installing PCMCIA cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145
At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145
At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146
At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149
Connecting the PCMCIA card reception channel . . . . . . . . . . . . . . . . . . . . . . . 151
At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151
Precautions when connecting PCMCIA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152
Connecting PCMCIA cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153
Product references for PCMCIA cards and installation . . . . . . . . . . . . . . . . . . . 154
Mounting cards and cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155
PCMCIA card operation display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157
Visual diagnostics of PCMCIA cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 158
Connection of TSX SCP 111 card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161
At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161
Point to point connection in Character Mode (DTE <==> DTE). . . . . . . . . . . . . 162
UNI-TELWAY, Modbus or Character Mode via Modem . . . . . . . . . . . . . . . . . . 163
Connection of the TSX SCP 112 card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164
At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164
Connection of the TSX SCP 112 card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165
Connecting in point to point mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166
Multidrop connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167
Dynamic performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168
TSX SCP 112 connection with April 5000/7000 PLCs. . . . . . . . . . . . . . . . . . . . 171
Connection of the TSX SCP 114 card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 178
At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 178
Connection to the UNI-TELWAY network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 179
Connecting to the Modbus/Jbus bus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 182
Multi-protocol asynchronous link connection RS 422 . . . . . . . . . . . . . . . . . . . . 185
Connection of the TSX FPP 20 card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 187
Connecting the TSX FPP 20 card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 187
Connection of the TSX FPP 10 card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 188
7.9
7.10
7.11
7.12
Connecting the TSX FPP 10 card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 188
Connection of the TSX MBP 100 card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 189
At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 189
Connecting the TSX MBP100 card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 190
General principle for connecting the PCMCIA card. . . . . . . . . . . . . . . . . . . . . . 191
Grounding the TSX MBP CE 030/060 cable . . . . . . . . . . . . . . . . . . . . . . . . . . . 192
Connecting the TSX MBP CE 030/060 cable to Modicon connection device 990 NAD
230 00 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 193
Summary of connection devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 196
Summary of connection devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 196
Precautions when connecting PCMCIA cards. . . . . . . . . . . . . . . . . . . . . . . . . . 198
Precautions for connecting PCMCIA cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . 198
Consumption of PCMCIA cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 199
Consumption of PCMCIA cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 199
Part V Communication: modules TSX ETY 110/410/510 . . . . 201
At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 201
Chapter 8
8.1
8.2
8.3
8.4
8.5
8.6
8.7
8.8
Communication: TSX ETY 110 module. . . . . . . . . . . . . . . . . . 203
At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Characteristics of the Ethernet channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Characteristics of Ethernet channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installing the TSX ETY 110 module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Selecting the type of processor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wiring/Unwiring with power switched on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Station address coding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connection via the AUI interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connection by AUI interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10baseT Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10baseT interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Display panel, diagnostics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Display panel, diagnostics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electrical features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
203
204
204
205
205
206
206
207
207
208
209
210
211
212
212
215
215
217
217
218
218
Chapter 9
Communication: modules TSX ETY 410/510 . . . . . . . . . . . . . 219
9.1
At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 219
At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 220
At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 220
9
9.2
9.3
9.4
9.5
9.6
9.7
9.8
9.9
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 221
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 221
Characteristics of the Ethernet channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 222
Characteristics of the Ethernet channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 222
Installation of modules TSX ETY 410/510 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 223
At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 223
At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 224
Selecting the type of processor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 225
Wiring/Unwiring with power switched on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 226
10/100baseT interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 227
10/100base T interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 227
Display, diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 228
Display panel, diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 228
Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230
Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230
Standards. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 231
Norms and standards. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 231
Operating conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 232
Operating conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 232
Part VI Communication: PCMCIA Modem card . . . . . . . . . . . . . 233
At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 233
Chapter 10
10.1
10.2
10.3
10.4
10.5
10.6
10
Installing the TSX MDM 10 module . . . . . . . . . . . . . . . . . . . . 235
At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 235
At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 236
At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 236
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 237
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 237
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 238
At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 238
Selecting the type of processor and slot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 239
Wiring/Unwiring with power switched on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 240
Connecting to the telephone network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 240
Connecting adapters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 242
Different adapters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 242
Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 243
Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 243
Technical specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 244
At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 244
Communication protocols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 245
Operating characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 246
Maximum operating temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 247
EC labeling. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 248
Index
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 249
11
12
About the book
At a Glance
Document Scope
This manual describes how to install network and bus interfaces on PLCs from the
Premium and Atrium range.
It is made up of 6 sections:
1. Communication on the processor’s terminal port
2. FIPIO communication master integrated into processors
3. AS-i bus interface: moduleTSX SAY 100
4. Communication: module TSX SCY 21601 and PCMCIA cards
5. Communication: modules TSX ETY 110/410/510
6. Communication: PCMCIA Modem cardTSX MDM 10
Validity Note
The update of this document is also valid for the new processors and TSX ETY 410
and ETY 510 modules.
Revision History
User Comments
TSX DM 57 40E 09.2000
Rev. No.
Changes
1
First conversion
We welcome your comments about this document. You can reach us by e-mail at
[email protected]
13
About the book
14
TSX DM 57 40E 09.2000
Terminal Port Communication
I
At a Glance
Aim of this Part
This part introduces the communication function via the Terminal Port for Premium
and Atrium processors
What’s in this
part?
This Part contains the following Chapters:
TSX DM 57 40E 09.2000
Chapter
Chaptername
Page
1
Terminal Port
17
2
TSX P ACC 01 device
49
15
Terminal Port
16
TSX DM 57 40E 09.2000
Terminal Port
1
At a Glance
Aim of this
Chapter
This Chapter introduces the functions of the Terminal Port for Premium and Atrium
processors.
What’s in this
Chapter?
This Chapter contains the following Sections:
TSX DM 57 40E 09.2000
Section
Topic
Page
1.1
Introduction to the terminal port
18
1.2
Connections
26
1.3
Appendices
45
17
Terminal Port
1.1
Introduction to the terminal port
At a Glance
Aim of this
Section
This Section introduces the communication function from the Terminal port of a PLC.
What’s in this
Section?
This Section contains the following Maps:
18
Topic
Page
Introduction to the terminal port
19
Communication with a programming/adjustment terminal
21
Communicating with a man-machine interface console
23
UNI-TELWAY master/slave communication
24
Character string communication
25
TSX DM 57 40E 09.2000
Terminal Port
Introduction to the terminal port
At a Glance
As the terminal port uses master UNI-TELWAY, slave UNI-TELWAY and character
string communication methods; the following documentation must be referred to for
installing the hardware and software for these different methods of communication:
l TSX DG UTW F: UNI-TELWAY Bus communication (user guide).
l TSX DR NET F: X-WAY communication (reference manual).
l TLX DS COM PL7 40F: Micro/Premium PLC communication (software installation manual).
Premium PLCs
The terminal port on Premium processors is a non-insulated RS 485 link made up
of two 8-pin mini-DIN connectors. These two connectors function identically and are
found on the processor. They are marked with TER and AUX and are used to physically connect two pieces of equipment together at the same time, such as a programming/adjustment terminal and a man-machine interface console.
Illustration:
The TER connector also allows power to be supplied to a device which does not
have its own power supply (RS 485/RS 232 connecting cable converter, insulating
device TSX P ACC 01 (See TSX P ACC 01 device, p. 49), etc.
The terminal port functions by default in master UNI-TELWAY mode. Via configuration it is possible to switch to UNI-TELWAY slave or character mode.
Note: The communication mode (e.g. master UNI-TELWAY, UNI-TELWAY slave
or character mode) is the same on both the TER and AUX connectors.
TSX DM 57 40E 09.2000
19
Terminal Port
Atrium PLCs
Atrium processors have one single TER terminal port which is identical in all respects to the TER terminal port on Premium PLCs. This is a non-insulated RS 485
link which is made up of a 8-pin mini DIN connector which is used to physically link
up a device, such as a programming/adjustment terminal or a man-machine interface console.
Illustration:
This connector is used to supply power to a device which does not have its own power supply (connecting cable converter RS 485/RS 232, insulating device
TSX P ACC 01 (See TSX P ACC 01 device, p. 49), etc).
The terminal port functions by default in master UNI-TELWAY mode. Via configuration it is possible to switch to UNI-TELWAY slave or character mode.
Note: Using a TSX P ACC 01 insulating device makes it possible to duplicate the
terminal port in order to use two TER and AUX ports like on the Premium PLC processor
20
TSX DM 57 40E 09.2000
Terminal Port
Communication with a programming/adjustment terminal
General
Configured in master UNI-TELWAY (default function), the terminal port is used to
connect a programming/adjustment terminal.
Premium station:
Programming/adjustment terminal
FT 2010/FTX 517 - PC
Atrium station:
PCX 57
Programming/
adjustment terminal
Host PC
Programming/
adjustment terminal
FT 2010/FTX 517 - PC
TSX DM 57 40E 09.2000
21
Terminal Port
Note: When using an Atrium Station, the programming terminal is generally the PC
which accepts the PCX 57 processor. However, as for a Premium station, the programming terminal can also be a PC type terminal connected to the processor port.
22
TSX DM 57 40E 09.2000
Terminal Port
Communicating with a man-machine interface console
General
Configured in master UNI-TELWAY mode (default function), the terminal port makes
it possible to manage man-machine interface device.
The man-machine interface device uses UNI-TE protocol to communicate with the
local PLC and the other stations on the network architecture.
When using a Premium PLC, the man-machine interface terminal should be connected to the AUX connector in order to free the TER connector for possible connection of a programming/adjustment terminal.
Premium station:
Master Premium
Atrium station:
Host PC
Master Atrium
CCX 17 slave
TSX DM 57 40E 09.2000
23
Terminal Port
UNI-TELWAY master/slave communication
General
The default communication mode for the terminal port is master UNI-TELWAY. It is
mainly used to link up a programming terminal and a slave man-machine interface
console.
Illustration:
Master Premium
Client
Client/Server
Slave
Slave
Client/Server
FT 2010/FTX 517
CCX 17
Note: When using an Atrium PLC or if the processor only has one terminal port,
this type of connection can be made by using a TSX P ACC 01 device. (See
TSX P ACC 01 device, p. 49)
24
TSX DM 57 40E 09.2000
Terminal Port
Character string communication
General
This mode is used to connect up a printer or specialized console (screen control, table controller etc.) to the terminal port of a Premium or Atrium PLC.
Illustration
Premium
TSX RKY
Atrium
or
Control screen
or
or
Loop Controller
Control screen
Printer
or
Loop Controller
Printer
TSX DM 57 40E 09.2000
25
Terminal Port
1.2
Connections
At a Glance
Aim of this
Section
This Section deals with the different connections of the Terminal port.
What’s in this
Section?
This Section contains the following Maps:
26
Topic
Page
Connections
27
Programming/Adjustment terminal
28
Man-machine interface console
30
Programming/adjustment terminal and man-machine interface console
31
Modem on terminal port
32
Master UNI-TELWAY
34
Slave UNI-TELWAY
35
Inter-PLC UNI-TELWAY
36
Inter-device UNI-TELWAY
38
Master PLC type TSX model 40
39
Character string
40
Summary table of terminal port connections
43
TSX DM 57 40E 09.2000
Terminal Port
Connections
General
The connector marked TER is used to connect any device which supports
UNI-TELWAY protocol, in particular devices which do not have their own power supply (RS 485/RS 232 connector cable converters, TSX P ACC 01 (See
TSX P ACC 01 device, p. 49) isolation device, etc.
The connector marked AUX (only on Premium PLCs) only enables devices which
have a power supply to be connected (eg. man-machine interface console, third-party devices, etc).
The terminal port has three function modes:
l Master UNI-TELWAY (default configuration)
l Slave UNI-TELWAY
l Character string
Illustration:
Atrium
Premium
Note: For Premium PLCs with two connectors (TER and AUX), the operating mode
defined in configuration (master UNI-TELWAY, slave UNI-TELWAY, character
mode) is the same for both connectors.
Methods of
connection
According to the operating mode selected in configuration, the terminal port is used
to connect:
l Premium PLC programming and adjustment terminals
l Man-machine interface devices
l Another PLC, using the TSX P ACC 01 connection device
l UNI-TELWAY devices (sensors/actuators, speed controller etc.)
l A printer or a control screen (link in character string mode)
l A modem
Note: Connecting a Premium/Atrium PLC slave to a UNI-TELWAY Bus requires
the use of a TSX P ACC 01 device.
TSX DM 57 40E 09.2000
27
Terminal Port
Programming/Adjustment terminal
General
28
Terminals with their own power supply (FTX 417, FTX 517) can be connected to
both TER and AUX connectors on Premium processors.
If a terminal does not have its own power supply, it must be connected to the processor TER connector.
The programming terminal uses UNI-TE protocol to program, adjust or diagnose the
local PLC and all the station devices.
If the PLC is connected to a network architecture, the transparency network enables
the programming terminal to reach all the devices in the architecture.
The product reference for the different connection cables is given below.
TSX DM 57 40E 09.2000
Terminal Port
Examples of connection:
Atrium
PC/
FT2100
TSX FTX CBF 020
(RS 485)
OU
(RS 485/232)
Programming/adjustment
Host
PC
TSX P CU1030
PC/FT2100
TSX RKY
OU
FTX 517
Programming/adjustment
Programming/adjustment
TSX FTX CBF 020
(RS 485)
TSX P CU1030
(RS 485/232)
Premium
FTX 517
Programming/adjustment
TSX DM 57 40E 09.2000
29
Terminal Port
Man-machine interface console
General
The man-machine interface device uses UNI-TE protocol to communicate with the
local PLC and the other stations in the network architecture.
A man-machine console with its own power supply on a Premium PLC must be connected to the AUX port in order to leave the TER port free for a terminal which needs
a power supply (FTX 117 Adjust for example).
The product references for connector cables between the terminal port and a
CCX 17 man-machine interface console are given below.
Examples of connection:
Premium
TSX RKY
XBT-Z968
T CCX CB10 002
(provided with the CCX 17)
Host PC
CCX 17: MMI
console
XBT-Z968
T CCX CB10 002
(provided with the CCX 17)
CCX 17: MMI
console
30
TSX DM 57 40E 09.2000
Terminal Port
Programming/adjustment terminal and man-machine interface console
General
The terminal port on a Premium processor can manage two devices in multidrop: the
programming/adjustment terminal and an man-machine interface console.
Each of the two connectors on the processor can receive one of these devices.
Examples of connection:
T FTX CBF 020
XBT-Z 968
T CCX CB10 002
(provided with the CCX 17)
FTX 517:
Programming/
adjustment terminal
CCX 17:
MMI
console
Note: Each connected terminal can be disconnected without disrupting the operation of the other. For an Atrium PLC or if the processor only has one terminal port,
this type of connection can be made by using a TSX P ACC01 (See TSX P ACC
01 device, p. 49) device.
TSX DM 57 40E 09.2000
31
Terminal Port
Modem on terminal port
General
The terminal port on Premium PLCs is compatible with a modem connection in all
protocols: Master UNI-TELWAY, Slave UNI-TELWAY and Character string.
Modem
characteristics
The modem which is to be connected must have the following characteristics:
1. Support 10 or 11 bits per character if the terminal port is used in UNI-TELWAY
mode:
l 1 bit for Start
l 8 bits of Data
l 1 bit for Stop
l Odd parity or without parity
2. Operate without any data compression if the terminal port is used in
UNI-TELWAY.
3. Be able to be "forced DTR signal" configured for its RS 232 serial port (if the modem is used in response mode), as this signal is not connected by the cable.
4. Operate without flow control (neither hardware: RTS/CTS, or software: XON/
XOFF) for its RS 232 serial port, as the cable to be used for the terminal port can
only carry TX, RX and GND signals.
5. Operate without data carrier check. Warning: this operating mode also uses RTS
and CTS control signals.
6. Accept an incoming telephone call while characters arrive at its RS 232 serial port
(if a modem/telephone network is used in response mode on a terminal port configured in master UNI-TELWAY).
Note: It is strongly recommended that you check with your dealer that the abovementioned characteristics are offered by the intended modem.
32
TSX DM 57 40E 09.2000
Terminal Port
Examples
Connecting to a Premium PLC:
Note: Connection on an
Atrium is identical.
TSX CTC 09 adapter if
necessary
Modem
TSX PCX 1130
l In Master UNI-TELWAY mode with the terminal port connected to a modem/telephone network in response mode, this modem must have all the above characteristics (1 to 6).
l In character string mode with the terminal port connected to a modem via a specialized line, this modem must have the characteristics of 3 to 5 above.
Configuring the
terminal port
TSX DM 57 40E 09.2000
In UNI-TELWAY mode the following parameters must be observed and set in the
configuration in PL7 software:
l The wait timeout must be between 100 and 250 ms
l In master mode the number of configured slaves must correspond to the actual
number of slaves present on the bus.
l In slave mode the number of addresses must correspond to those used.
33
Terminal Port
Master UNI-TELWAY
General
This is the terminal port default operating mode. It is principally used for:
l Connecting a programming/adjustment terminal and a man-machine interface
console if a Premium PLC is used.
l Connecting a programming/adjustment terminal or man-machine interface console in the case of an Atrium PLC with only one terminal port.
Examples of connection:
Premium master
T FTX CBF 020
XBT-Z 968
Client
Client/Server
T CCX CB10 002
(provided with the
CCX 17)
slave
slave
Client/Server
FTX 517
CCX 17
Note: In the case of an Atrium station where the processor only has one terminal
port, this type of connection can be made by using a TSX P ACC 01
Important
information
34
The master can scan up to eight link addresses:
l Link addresses 1,2 and 3 are reserved for the programming terminal.
l The five other addresses are available for connecting a device such as a manmachine interface, slave PLC, sensors/actuators or any other slave device which
supports UNI-TE protocol. Addresses 4 and 5 are reserved for a man-machine
interface console, it one is used (addresses are forced by using a XBT-Z 968 cable).
This functioning mode is immediately operational. Within the limits of the default
configuration, no installation phase is required to connect a device to this type of link.
TSX DM 57 40E 09.2000
Terminal Port
Slave UNI-TELWAY
General
The UNI-TELWAY slave protocol of the terminal port is used to build a slave Premium or Atrium PLC into a UNI-TELWAY bus managed by a Premium or Atrium PLC
(PCMCIA communication card or terminal port).
For this connection to be possible it is essential to use a TSX P ACC 01 connection
device.
Examples of connection:
Premium master
Communication
card
PCMCIA
TSX SCP 114
TSX SCP CU 4030 cable
S1=ON
S2=ON
S1=ON
S2=ON
UNI-TELWAY bus
TSX P
ACC 01
TSX
SCA 50
TSX
SCA 50
TSX
SCA 62
TSX P
ACC 01
TSX CSC 015
Premium
Slave
ATV 16
Slave
TSX 17-20
Slave
Atrium
Slave
A slave PLC manages up to three consecutive link addresses:
l Ad0 (system address
l Ad1 (client application address)
l Ad2 (listen application address)
TSX DM 57 40E 09.2000
35
Terminal Port
Inter-PLC UNI-TELWAY
General
The terminal port on Premium processors allows two PLCs to be connected, one the
master and the other the slave.
For this connection to be possible it is essential to use a TSX P ACC 01 (See
TSX P ACC 01 device, p. 49) connection device. The different options for connecting
this device are given later.
Example of
connecting two
Premium PLCs
Illustration:
Premium slave
Premium master
TSX PCU 1030
T FTX CB 1020/1050
TSX P ACC 01
FT 2100 slave
36
S1=ON
S2=ON
TSX DM 57 40E 09.2000
Terminal Port
Example of
connecting a
Premium PLC
and an Atrium
PLC
Illustration:
Premium master
TSX RKY
TSX P CU 1030
Atrium slave
FT 2100 slave
T FTX CB 1020/1050
TSX P ACC 01
S1=ON
S2=ON
TSX DM 57 40E 09.2000
37
Terminal Port
Inter-device UNI-TELWAY
General
The terminal port on Premium/Atrium PLCs enables them to be connected to a
UNI-TELWAY bus in order to communicate with devices such as speed controllers,
sensor/actuators or with other PLCs
Connecting a Premium/Atrium (master or slave) PLC to a UNI-TELWAY bus requires the use of a TSX P ACC 01 (See TSX P ACC 01 device, p. 49) device.
Example
Examples of connection:
FTX 417 slave
T FTX CBF 020
Premium master
S1=ON
S2=ON
UNI-TELWAY bus
TSX P ACC 01
TSX SCA 50
TSX SCA 62
CCX 17
ATV 16 slave
The connected devices communicate with the PLC using UNI-TE protocol.
Communication between the different components is allowed.
The programming terminal can directly access all these devices to carry out adjustments and diagnostics functions.
Note: To install TSX SCA 50 and TSX SCA 62 devices, consult the TSX DG UTW
manual: UNI-TELWAY Bus communication.
38
TSX DM 57 40E 09.2000
Terminal Port
Master PLC type TSX model 40
General
A TSX/PMX model 40 PLC can also be configured in master mode on a
UNI-TELWAY bus and can control slave Premium/Atrium PLCs
Example of connection
FT 2... slave
TSX 107-40 master
TSX PCU1030
S1=ON
S2=ON
S1=ON
S2=ON
TSX CSB 015
UNI-TELWAY bus
TSX P ACC 01
TSX SCA 62
Premium slave
TSX P ACC 01
Premium slave
Note: To install TSX SCA 50 and TSX SCA 62 devices, consult the TSX DG UTW
manual: UNI-TELWAY Bus communication
TSX DM 57 40E 09.2000
39
Terminal Port
Character string
General
The terminal port, when configured in character mode, can be used to connect a device such as a printer, display screen or a specialized console (table controller for
example).
Examples of connection:
Premium
TSX RKY
RS485/RS 232
converter cable
Host PC
Control
screen does
not manage
the RTS
signal
OU
RS485/RS 232
converter cable
Atrium
Converter cable RS485/
RS 232 TSX PCX 1030
Control
screen does
not manage
the RTS
Loop Controller signal
OU
OU
RS485/RS 232
converter cable
RS485/RS 232
converter cable
Printer
Loop
OU
RS485/RS 232
converter cable
Printer
40
TSX DM 57 40E 09.2000
Terminal Port
Note: In order to ensure all types of connection TSX PCX 1030 and TSX PCX 1130
cables are delivered with adapters:
l The TSX PCX 1030 cable is delivered with two adapters/converters:
l TSX CTC 07: male 9-pin to female 25-pin.
l TSX CTC 08: male 9-pin to male 25-pin.
l The TSX PCX 1130 cable is delivered with one adapter/converter:
l TSX CTC 09: male 9-pin to male 25-pin.
TSX DM 57 40E 09.2000
41
Terminal Port
Precautions of
use
The TSX P CD 1030 cable ensures RS 485/RS 232 conversion and provides ‘peripheral slave’ information for the printer. It does not function on the AUX port and
the connected device must manage the RTS signal.
Using the TSX PCD 1030 cable means also adjusting the configuration of the TER
port for 8 bits of data only.
TSX PCX 1030 and TSX PCX 1130 cables must only be connected to the TER port
of the PLC to supply RS 485/RS 232 conversion electronics. To avoid signal conflicts it is prohibited to connect a device to the AUX port of the PLC.
42
TSX DM 57 40E 09.2000
Terminal Port
Summary table of terminal port connections
General
Adjustment of
cables
TSX PCX 1030
and
TSX PCX 1130
TSX DM 57 40E 09.2000
The table below can be used to define the cable linking terminal port connectors of
a Premium/Atrium PLC to peripheral devices.
Connection cable TER
Port
AUX
Port
Example of connected devices
TSX CB 1020
TSX CB 1050
X
TSX P ACC 01
X
FTX 517, FTX 417
T FTX CBF 020
X
TSX P CU 1030
X
TSX P CD 1030
X
XBT-Z938
X
TSX P ACC 01
X
Connection to UNI-TELWAY
TSX PCX 1030
X
Devices not managing RTS signal DTE<-->DTE type:
RS 232 programming terminals, printers
TSX PCX 1130
X
Devices not managing RTS signal DTE<-->DCE type:
Modem
FT 2100, RS 232 programming and adjustment terminals
Graphics terminals and printers managing RTS signal
X
CCX 17, XBT
The two cables TSX PCX 1030 and TSX PCX 1130 convert RS 485 and RS 232 signals. They authorize the connection of the terminal port to RS 232 devices which do
not manage RTS.
Both are equipped with a switch which enables the PLC to be positioned in either
Master of Slave mode. The switch is accessible internally by removing the metal
cover containing the electronics.
43
Terminal Port
The management of the switch is as follows:
PL7 Master
UNI-TELWAY
configuration
PL7 Slave
UNI-TELWAY
configuration
PL7 character mode
configuration
Switch
position M
UNI-TELWAY Master
with PL7 configuration
UNI-TELWAY Master
with default configuration
UNI-TELWAY Master
with default configuration
Switch
position S
UNI-TELWAY Slave
with default configuration
UNI-TELWAY Slave
with PL7 configuration
Character Mode with
PL7 configuration
Illustration:
Master mode M
44
Slave mode S
TSX DM 57 40E 09.2000
Terminal Port
1.3
Appendices
At a Glance
Aim of this
Section
This Section contains the appendices relating to the Terminal port.
What’s in this
Section?
This Section contains the following Maps:
TSX DM 57 40E 09.2000
Topic
Page
Characteristics of the terminal port
46
Terminal port connector pin configuration
48
45
Terminal Port
Characteristics of the terminal port
General
The characteristics of the terminal port are given in the table below:
Character mode
Structure
Physical
interface
Non-insulated RS 485
Non-insulated RS 485
Transmission
Protocol
Master/slave multidrop
Without protocol
Binary flow
19200 bits/s by modifiable
default of 1200 to 19200
bits/s (1 start bit; 8 data
bits; even parity, odd parity or without parity; 1 bit
stop).
9600 bits/s by modifiable
default of 1200 to 19200
bits/s (7 or 8 data bits;
even parity, odd parity or
without parity; with or without echo.
Number of
devices
Eight maximum (eight ad- A device (point to point)
dresses managed by the
master). In slave mode
addresses 4, 5, 6 are selected by default. In master mode the reserved
addresses are:
l 1,2, and 3 for the programming terminal
l 4 and 5 if a CCX 17 is
present
The other addresses are
available.
Length
10 meters maximum
Configuration
46
UNI-TELWAY master or
slave mode
10 meters maximum
TSX DM 57 40E 09.2000
Terminal Port
Services
UNI-TELWAY master or
slave mode
Character mode
UNI-TE
Requests in point to point
with report of 128 octets
maximum initiated by any
connected device. There
is nothing broadcast from
the master.
Character string 129 octets maximum. Messages
must end with $OD (carriage return).
Other functions
Transparency of communication with all devices in
a network architecture via
the master.
-
Safety
A character check on each No error indication.
frame, acknowledgment
and repeat option.
Monitoring
Table of bus state, status
of devices, error counters
can be accessed on the
slaves
No flow monitoring
Note: Using a TSX P ACC 01 (See TSX P ACC 01 device, p. 49) connection device enables the RS 485 link to be used in remote mode.
TSX DM 57 40E 09.2000
47
Terminal Port
Terminal port connector pin configuration
General
The terminal port connectors marked TER and AUX are 8-pin mini-DIN which can
be locked.
The signals are given below:
1
2
3
4
5
6
7
8
D (B)
D (A)
not connected
/DE
/DTP (1 = master)
not connected
0 volt
5 volts
1
2
3
4
5
6
7
8
D (B)
D (A)
not connected
/DE
/DTP (1 = master)
not connected
0 volt
not connected
Note: The operation of the terminal port depends on two parameters:
l Signal status/DTP (0 or 1), fixed by cabling accessory (TSX P ACC 01 cable).
l Software configuration of the terminal port defined in PL7.
The table below defines the functioning mode of the terminal port according to these
two parameters:
48
PL7 configuration Signal /DTP = 0
Signal /DTP = 1
Master
UNI-TELWAY
Terminal port in UNI-TELWAY
slave mode (default)
Terminal port in UNI-TELWAY
master mode
Slave
UNI-TELWAY
Terminal port in UNI-TELWAY
slave mode
Terminal port in UNI-TELWAY
master mode (default)
Character mode
Terminal port in character mode
Terminal port in UNI-TELWAY
master mode (default)
TSX DM 57 40E 09.2000
TSX P ACC 01 device
2
At a Glance
Aim of this
Chapter
This Chapter introduces the functions of the TSX P ACC 01 connection device.
What’s in this
Chapter?
This Chapter contains the following Sections:
TSX DM 57 40E 09.2000
Section
Topic
Page
2.1
At a Glance
50
2.2
Hardware installation
53
2.3
Example of topologies
60
49
TSX P ACC 01
2.1
At a Glance
At a Glance
Aim of this
Section
This Section describes the general characteristics of the TSX P ACC 01 device.
What’s in this
Section?
This Section contains the following Maps:
50
Topic
Page
Standard functions
51
External appearance
52
TSX DM 57 40E 09.2000
TSX P ACC 01
Standard functions
General
The TSX P ACC 01 device is a wiring accessory which links up to the TER connector
on Premium/Atrium PLC processors via an integrated cable with a mini-DIN connector at one of its ends.
This is used to:
l Connect several devices to the terminal port on Premium/Atrium PLCs. To do
this, it is equipped with two mini-DIN connectors, marked TER and AUX, which
operate identically to the TER and AUX connectors on Premium PLC processors.
l Insulate UNI-TELWAY signals, in order to extend the link on Premium PLC terminal ports to more than 10 meters for connecting to a UNI-TELWAY bus.
l Adapt the bus when the device is connected to one of the ends of the
UNI-TELWAY bus.
l Fix the functioning mode of the terminal port:
l Master UNI-TELWAY
l UNI-TELWAY slave or character mode
Note: The two TER and AUX ports on the TSX P ACC 01 device are not insulated
from each other nor from the TER port on the PLC which provides the power.
TSX DM 57 40E 09.2000
51
TSX P ACC 01
External appearance
General
This device is made from zamak and of the same type as UNI-TELWAY branching
or connection devices (TSX SCA 50 and TSX SCA 62). It is designed to be mounted in a cabinet. Its protection index is IP20.
Illustration:
Terminal ports
Connection cable to TER port
for Premium PLC (length 1 m)
52
TSX DM 57 40E 09.2000
TSX P ACC 01
2.2
Hardware installation
At a Glance
Aim of this
Section
This Section deals with installing hardware for connection devices TSX P ACC 01.
What’s in this
Section?
This Section contains the following Maps:
TSX DM 57 40E 09.2000
Topic
Page
Dimensions and mounting
54
Internal view
55
Connection to UNI-TELWAY Buses
56
Connecting to Premium and Atrium PLCs
57
Switch configuration
58
TSX P ACC 01 connector pin configuration
59
53
TSX P ACC 01
Dimensions and mounting
General
The TSX P ACC 01 device is installed on a AM1-PA••• perforated board or on a DIN
rail with a LA9 D9976 mounting plate.
Illustration:
AM1-PA...
AM1-DE/DP
54
TSX DM 57 40E 09.2000
TSX P ACC 01
Internal view
Illustration
S1 Selects functioning mode (master or slave),
S2 Adapts the line end,
JA and JB Connection terminals on the UNI-TELWAY Bus.
TSX DM 57 40E 09.2000
55
TSX P ACC 01
Connection to UNI-TELWAY Buses
General
The TSX P ACC 01 device is connected to the UNI-TELWAY Bus using connection
terminals JA and JB as shown below:
Illustration:
Shielding
Insulating sleeve
(essential)
White
Red
White
Blue
56
TSX DM 57 40E 09.2000
TSX P ACC 01
Connecting to Premium and Atrium PLCs
General
When the TSX P ACC 01 device has to be supplied, it must be connected by its
built-in cable to the TER connector on the PLC processor.
The device can be connected and disconnected when the PLC is switched on.
Illustration:
Premium
TSX RKY
Host PC
Atrium
TSX P ACC 01
TSX P ACC 01
Note:
Only one TSX P ACC 01 device can be connected to a Premium/Atrium PLC.
TSX DM 57 40E 09.2000
57
TSX P ACC 01
Switch configuration
General
l Configuring line end adaptation
Line ends are adapted by the S2 switch as indicated below.
l Configuring the operating mode
The operating mode is selected by switch S1 as indicated below.
Illustration:
End of line position
UNI-TELWAY
Other positions
UNI-TELWAY
slave or
character mode
UNI-TELWAY master
Note: The operating mode selected only concerns the connection cable leading to
the TER connector on the PLC processor.
58
TSX DM 57 40E 09.2000
TSX P ACC 01
TSX P ACC 01 connector pin configuration
General
The TSX P ACC 01 device has two parallel connectors, marked TER and AUX.
The signals are given below :
1
2
3
4
5
6
7
8
TSX DM 57 40E 09.2000
D(B)
D(A)
not connected
not connected
not connected
not connected
0V
5V
1
2
3
4
5
6
7
8
D(B)
D(A)
not connected
not connected
not connected
not connected
not connected
not connected
59
TSX P ACC 01
2.3
Example of topologies
At a Glance
Aim of this
Section
This Section introduces examples of how to use the TSX P ACC 01 device.
What’s in this
Section?
This Section contains the following Maps:
60
Topic
Page
Connecting devices
61
UNI-TELWAY master mode
63
UNI-TELWAY slave mode
65
Connection between two PLCs
66
TSX DM 57 40E 09.2000
TSX P ACC 01
Connecting devices
General
The two TER and AUX ports on the TSX P ACC 01 device have the same standard
functions as the TER and AUX connectors on Premium/Atrium PLC station processors.
l The TER connector on the device is used to connect any device which supports
UNI-TELWAY protocol, and in particular link up devices without their own power
supply (RS 485/RS 232 cable converter, etc)
l The AUX connector on the device is only used to connect devices with a power
supply (man-machine interface console, third-party devices etc).
Note: The TSX P ACC 01 device is supplied from the TER connector on the PLC
to which is it connected. As a result, the TER connector on the device enables devices with their own power supply (CCX 17 etc) or without their own power supply
(RS 485/RS 232 cable converter etc) to be supplied.
If the user wants to connect the terminal port of a second PLC to one of the ports
on the TSX P ACC 01 device, AUX connectors (on the device and PLC) must be
used to avoid power supply conflicts on the two PLCs.
Example 1:
Premium master
Premium slave
T FTX CB 1020/1050
TSX P ACC 01
TSX DM 57 40E 09.2000
61
TSX P ACC 01
Example 2:
Premium master
TSX RKY
T FTX CB 1020/1050
Atrium slave
TSX P ACC 01
62
TSX DM 57 40E 09.2000
TSX P ACC 01
UNI-TELWAY master mode
Example
A TSX P ACC 01 device is connected to a UNI-TELWAY link master PLC as in the
example below.
Switches S1 and S2 must be positioned on OFF (master mode).
Example on a Premium station:
FT 2100 slave
Premium master
Addresses 1, 2, 3
TSX P CU 1030
TSX SCA 50
S1=OFF
S2=OFF
UNI-TELWAY bus
TSX P ACC 01
TSX SCA 62
XBT-Z 968
TSX CSC 015
T CCX CB 10 002
ATV 16
slave
Address 6
CCX 17
slave
Addresses 4/5
TSX 17-20
slave
Addresses 7/8
1000 meters maximum
TSX DM 57 40E 09.2000
63
TSX P ACC 01
Example on an Atrium station:
TSX RKY
FT 2100 slave
host PC
Atrium master
S1=OFF
S2=OFF
Addresses 1, 2, 3
UNI-TELWAY bus
TSX P CU 1030
TSX SCA 50
TSX P ACC 01
TSX SCA 62
XBT-Z 968
T CCX CB 10 002
ATV 16
slave
Address 6
CCX 17
slave
Addresses 4/5
TSX CSC 015
TSX 17-20
slave
Addresses 7/8
1000 meters maximum
64
TSX DM 57 40E 09.2000
TSX P ACC 01
UNI-TELWAY slave mode
Example
A TSX P ACC 01 device is connected to a UNI-TELWAY link slave PLC as in the
example below.
Note: Important: For a PLC to be able to operate in slave mode it must be connected to a TSX P ACC 01 device by the cable built into it.
Illustration:
FT 2100
TSX P CU 1030
TSX 107-40 master
S1=ON
S2=ON
TSX CSB 015
S1=ON
S2=ON
UNI-TELWAY bus
TSX P ACC 01
TSX SCA 62
TSX P ACC 01
Premium
XBT-Z 968
TCCX CB10 002
Atrium slave
CCX 17
1000 meters maximum
TSX DM 57 40E 09.2000
65
TSX P ACC 01
Connection between two PLCs
Reminders
If the user wants to connect the terminal port of a second PLC on one of the ports of
the TSX P ACC 01 device, the AUX port must be used to avoid power supply conflicts in the two PLCs.
Note: Important: For a PLC to be able to work in slave mode it must be connected
to a TSX P ACC 01 device by the device’s built-in cable.
In the example given below the TSX P ACC 01 device must therefore be connected
to the UNI-TELWAY slave PLC by the device’s integrated cable. Its S1 switch must
be positioned on ON
If the device if not placed on a UNI-TELWAY bus, the position of the S2 switch does
not matter.
Illustration:
Premium master
Premium slave
FT 2100
XBT-Z 968
T FTX CB1
020/050
TFTX P CU1030
T CCX CB10 002
S1=ON
S2=not significant
CCX 17
TSX P ACC 01
66
TSX DM 57 40E 09.2000
Processor-integrated master
FIPIO communication
II
At a Glance
Aim of this Part
This Part deals with the master FIPIO communication function, which is integrated
into Premium/Atrium processors.
What’s in this
part?
This Part contains the following Chapters:
Chapter
3
TSX DM 57 40E 09.2000
Chaptername
Processor-integrated master FIPIO communication
Page
69
67
Integrated FIPIO
68
TSX DM 57 40E 09.2000
Processor-integrated master
FIPIO communication
3
At a Glance
Aim of this
Chapter
This Chapter deals with the FIPIO communication function integrated into Premium/
Atrium processors.
What’s in this
Chapter?
This Chapter contains the following Maps:
TSX DM 57 40E 09.2000
Topic
Page
Review of the FIPIO bus
70
Integrated FIPIO link on Premium/Atrium processors
72
Examples of architecture
73
69
Integrated FIPIO
Review of the FIPIO bus
General
Main
characteristics
FIPIO is a field bus which is used to centralize inputs/outputs of a PLC station and
its industrial peripherals nearest to the section which is operating.
From a PLC station whose processor has a built-in FIPIO link, the FIPIO bus is used
to connect 1 to 127 devices such as:
l Momentum remote input/output modules (discrete and analog)
l TBX remote input/output modules (discrete and analog)
l CCX 17 command consoles
l ATV 16 variable speed controllers
l Devices which conform to standard profiles
l Agent PLCs, PC
l ...
The FIPIO field bus can be used in a single architecture (mono-station) or in a more
complex architecture (multi-station) where several FIPIO segments can be brought
together by a local network at a higher level such as FIPWAY or Ethernet TCP_IP
for example.
Structure
Nature
Open field bus, conforming to World FIP standards.
Topology
Links devices through chaining or branching.
Access method
Managed by a bus arbiter
Communication
By exchange of variables which can be accessed by the user
in the form of PL7 objects and X-WAY datagrams.
Privileged exchanges
Cyclical exchange of status variables and remote input/output
commands
Transmission
70
Binary flow
1Mb/s.
Medium
Shielded twisted pair (150 Ohms of characteristic impedance).
TSX DM 57 40E 09.2000
Integrated FIPIO
Configuration
Number of connection
points
128 logic connection points for whole architecture
Number of segments
15 maximum (in cascade format) using electrical or optical relays (14 maximum in cascade format).
PLC
One PLC (address connection point 0)
Programming terminal One programming terminal (must be connected to connection
point 63).
Length
TSX DM 57 40E 09.2000
The length of a segment depends on its type of branches:
l 1000 meters maximum without relay.
l 1500 meters maximum between the devices which are the
furthest apart.
71
Integrated FIPIO
Integrated FIPIO link on Premium/Atrium processors
General
Some processors have as standard an integrated master FIPIO link which makes it
possible to connect the PLC station to a FIPIO bus.
Illustration:
Link
FIPIO
Link
FIPIO
Link
FIPIO
Premium processor
Connecting to
the FIPIO bus
Atrium processor
The processor has a SUB D 9-pin connector which is used to link it to the FIPIO bus
using a TSX FP ACC12 connector.
Illustration:
TSX FP
ACC12
TSX FP
ACC12
The complete procedure for installing a FIPIO bus (architecture, type of cable to use,
cabling accessories etc.) is discussed in the FIPIO Bus reference manual.
Note: The master FIPIO link integrated into processors should not be taken into
account when counting the station channels.
72
TSX DM 57 40E 09.2000
Integrated FIPIO
Examples of architecture
Premium station
Illustration:
Premium
TSX RKY
X Bus
TBX
Momentum
CCX 17
ATV
PC
TSX DM 57 40E 09.2000
73
Integrated FIPIO
Atrium station
Illustration:
TSX RKY
PC
Atrium
TBX
Momentum
CCX 17
ATV
PC
74
TSX DM 57 40E 09.2000
AS-i bus interface: TSX SAY 100
module
III
At a Glance
Aim of this Part
This Part deals with the AS-i bus interface module: TSX SAY 100.
What’s in this
part?
This Part contains the following Chapters:
Chapter
4
TSX DM 57 40E 09.2000
Chaptername
AS-i bus interface module: TSX SAY 100
Page
77
75
TSX SAY 100
76
TSX DM 57 40E 09.2000
AS-i bus interface module:
TSX SAY 100
4
At a Glance
Aim of this
Chapter
This Chapter only deals with hardware installation of the TSX SAY 100 interface
module, AS-i bus master on a Premium/Atrium PLC. For the complete installation of
an AS-i bus you must refer to the following manuals:
l AS-i bus reference manual
l AS-i installation section in the Premium PLC Applications Manual - Applications,
Volume 1.
What’s in this
Chapter?
This Chapter contains the following Sections:
TSX DM 57 40E 09.2000
Section
Topic
Page
4.1
Review of the AS-i bus
78
4.2
Description of the TSX SAY 100 module
88
4.3
Input/output object addressing
100
4.4
AS-i Bus diagnostics
101
4.5
Operating modes of the TSX SAY 100 module
108
4.6
Precautions of use
110
77
TSX SAY 100
4.1
Review of the AS-i bus
At a Glance
Aim of this
Section
This Section introduces the main characteristics of the AS-i bus.
What’s in this
Section?
This Section contains the following Maps:
78
Topic
Page
Review of the AS-i bus
79
Overview of AS-i products from the Schneider catalog
80
Introduction to the main constituent elements
81
Example of AS-i bus topology
85
Main characteristics of the AS-i bus
86
TSX DM 57 40E 09.2000
TSX SAY 100
Review of the AS-i bus
General
The AS-i bus is a field bus (level 0) and can be used to connect sensors/actuators.
This allows "Discrete" type information to be routed between a bus master and sensor/actuator slaves.
AS-i is made up of three major basic elements:
l A dedicated power supply providing 30 VDC voltage.
l A bus master.
l Slaves (sensors and actuators).
The main types
of sensors/
actuators
1. Communication sensors/actuators:
With a built-in AS-i function they link up directly to the AS-i bus via a passive distributor or a T-piece connection.
2. The traditional IP65 sensors/actuators:
They connect to the bus via an AS-i interface (active distributor or Telefast IP20
discrete input-output bus interface). These interfaces connect the sensors and
traditional actuators to the AS-i bus and provide them with dialog capacity on the
bus.
Illustration:
Passive distributor
Active distributor
Connection T
AS-i Bus
AS-i function
integrated
AS-i function via
interface
Traditional product
124 products maximum
(124 input information
and 124 output information)
TSX DM 57 40E 09.2000
Communicating product
AS-i function
integrated
Communicating product
31 products (sensors or actuators)
79
TSX SAY 100
Overview of AS-i products from the Schneider catalog
General
Non-exhaustive list of AS-i products from the Schneider catalog:
Man/machine dialog
Sensors
AS-i
Actuators
AS-i
Start-up
motor
Detector
photoelectric
Inductive
proximity
detector
Interface for sensors and actuators
Distributor
active
80
Column
lit
Button
box
Keyboard
12 keys
Distributor
passive
2E/2S
4S
4E
For connection by M12 ports
of sensors/actuators/units of
dialog and signaling standards:
• inductive sensors.
• capacity switches.
• photoelectric barriers.
• end of run.
• LEDs
• relays.
• solenoid valve.
Master
Supply
Bus interface
Telefast
AS-i bus interface/discrete input-output.
•4I
•4O
• 8 I/O (4I + 4O)
4 channels for AS-i
sensors/actuators
connection equipped with
M12 sockets.
For connection by screw or pull-out
terminals of dialog sensors/
actuators/units of dialog and
signaling standards:
• 2 or 3 wire inductive sensors.
• capacity switches.
• end of run.
• LEDs
• relays.
• contactors.
• solenoid valve.
• resistance.
TSX DM 57 40E 09.2000
TSX SAY 100
Introduction to the main constituent elements
Cable
This transmits data and carries the power. It can be made up from:
l either an unshielded, polarized twin-wire AS-i ribbon cable.
l Or a standard round, shielded or unshielded twin-wire cable.
Illustration:
Guiding
ribbon cable
Active
distributors
IP67 sealed interfaces for connecting sensors/actuators using M12 connectors.
These distributors are used to connect "traditional", non-communicating sensors/actuators.
Illustration:
Active distributor
for ribbon cable
Passive
distributors
Active distributor for
round cable
IP67 sealed interfaces for connecting sensors/actuators using M12 connectors.
These distributors do not have any electronics and can therefore be used to connect
the "communicating" sensors/actuators.
Illustration:
Passive distributor
for ribbon cable
TSX DM 57 40E 09.2000
Round cable
Passive distributor
for round cable
81
TSX SAY 100
SB2 Telefast
discrete inputsoutputs/bus
interface
IP20 sealed interface with built-in ASi- function. It enables connection to all types of
"traditional" non-communicating sensors/actuators via screw terminal blocks.
Illustration:
AS-i actuators
The direct motor starters and toggle switches in sealed boxes (IP54 and IP65) ensure electrical motors are controlled and protected up to 4KW at 400 VAC.
Illustration:
AS-i sensors
l Photo-electric detectors:
They ensure that all kinds of objects (opaque, reflective etc) are detected with 5
basic systems: barrier, reflex, polarized reflex, proximity and proximity with background blanked out. They offer an IP67 protection level.
l Inductive proximity detectors:
They detect all metal objects and provide information for the check functions on
whether an object is present or not. They offer an IP67 protection level.
Illustration:
82
TSX DM 57 40E 09.2000
TSX SAY 100
Man-machine
interface
products
l Button boxes:
Signaling
elements
l Illuminated columns:
Bus master
Built into a Premium/Altrium PLC station, the TSX SAY 100 module (AS-i bus master) manages all data exchanges on the AS-i bus.
Illustration:
These are made up of dialog tools, which are perfectly adapted to exchanging information between the operator and machine.
l Keyboards:
Man/machine dialog tools, these have 12 touch sensitive keys. The information
delivered is coded in BCD on 4 bits. They offer an IP65 protection level.
Illustration:
Optical or sound signaling elements.
Premium/Atrium station
TSX DM 57 40E 09.2000
83
TSX SAY 100
AS-i power
supply
AS-i dedicated power supply, designed to supply the components connected to the
AS-i bus.
The distribution of this power supply uses the same medium as that used for data
exchange.
Illustration:
Connecting and
branching
accessories
T-piece connectors are used to make connections to the AS-i bus. These are designed for linking to AS-i ribbon cables or to ribbon/round cable branches.
Illustration:
T for
ribbon cable
84
Branch
ribbon/round cable
TSX DM 57 40E 09.2000
TSX SAY 100
Example of AS-i bus topology
General
Illustration:
Level 1
Premium
AS-i master
Level 0
AS-i Bus
Supply
AS-i
TSX DM 57 40E 09.2000
Sensors/actuators
communicating
Interfaces with
traditional sensors/
actuators
85
TSX SAY 100
Main characteristics of the AS-i bus
General
AS-i is a system in which exchange management is ensured by a single master who
calls in succession, by scanning the bus, each detected slave and awaits a response.
The communication series frame carries:
l 4 data bits (D0 to D3), which are the image of inputs or outputs according to the
nature of the interface.
l 4 parametering bits (P0 to P3), which are used to set the operating modes of the
interface.
P0 to P3 bits are used for "intelligent" devices, including AS-i ASIC (specific integrated circuit). Operation can be modified while it is running.
The address of the slave is coded on 5 bits.
At the request of the AS-i master, outputs are set and the inputs for AS-i devices are
sent in the slave’s response.
Slave addressing
Each slave connected to the AS-i bus must have an address between 1 and 31 (coding on 5 bits).
The slaves delivered from the factory have the address 0 (the address of the slave
is memorized in a non-volatile format).
Addresses are programmed using a terminal specifically for addressing, a XZMC11.
Note: When replacing a faulty slave whose address has been set, the address of
the slave to be replaced can be updated automatically.
Identification of
slaves
All slave devices connected to the AS-i bus are identified by:
l An I/O Code (input/output distribution code).
l An identification code, which completes the functional identification of the slave.
These identifications allow the AS-i master to recognize the configuration which is
present on the bus
These different profiles have been developed by the AS-i Association. They are
used to distinguish modules such as for inputs, outputs, mixed modules, "intelligent"
device families, etc.
Maximum
number of
inputs/outputs
An AS-i bus can support a maximum of 31 slaves.
Each slave can have a maximum of 4 inputs and/or 4 outputs.
This makes it possible to manage a maximum of 124 inputs + 124 outputs, or 240
discrete inputs/outputs when all active devices have 4 inputs and outputs.
86
TSX DM 57 40E 09.2000
TSX SAY 100
AS-i cable
The AS-i cable is a twin-wire link on which communications and power supply for the
connected devises are transmitted.
The link does not need to be twisted.
The cross-section of wires can be from 2 x 0.75 mm2, 2 x 1.5 mm2 or 2 x 2.5 mm2,
according to the current consumed by the devices.
Topology and
maximum length
of AS-i bus
The topology of the AS-I bus is flexible. It can be perfectly adapted to meet the user’s
needs (point to point, on line, tree structure etc.).
In every case, the total length of all the branches of the bus must not exceed 100
meters without a relay.
AS-i bus cycle
time
This is the cycle time between slave(s) and the TSX SAY 100 module.
The AS-i system always transmits information which is the same length to each
slave on the bus. The AS-i cycle time depends on the number of slaves connected
to the bus.
In the presence of 31 functioning slaves, this time period will be a maximum of 5 ms.
Reliability,
flexibility
Reliable operation is ensured by the transmission process used (Manchester current and coding modulation). The master monitors the line supply voltage and the
data sent. It detects transmission errors as well as slave failures, and sends the information to the PLC.
Exchanging or connecting a new slave during operation does not disturb communications between the master and the other slaves.
TSX DM 57 40E 09.2000
87
TSX SAY 100
4.2
Description of the TSX SAY 100 module
At a Glance
Aim of this
Section
This Section deals with hardware installation and the characteristics of the TSX SAY
100 module.
What’s in this
Section?
This Section contains the following Maps:
88
Topic
Page
Physical presentation
89
Mounting/installation
91
Connections
92
Displaying module states
95
Specific display panels on the TSX SAY 100 module
96
Technical characteristics
98
Personnel safety
99
TSX DM 57 40E 09.2000
TSX SAY 100
Physical presentation
General
The TSX SAY 100 module comes as a standard format module.
Illustration:
Front panel
Description of
TSX SAY 100
module
TSX DM 57 40E 09.2000
The module is made up of the following elements:
1. A display panel consisting of 4 LEDs for displaying the operating modes of the
module:
l RUN LED (green): lit indicates normal functioning mode of the module.
l ERR LED (red): lit indicates a module error.
l COM LED (green): lit indicates data exchanges on the AS-i network.
l I/O LED (red): lit indicates an external input/output error on the AS-i bus.
2. Display panel consisting of 32 LEDs (0 to 31) which enable AS-i bus diagnostics,
and display the state of each slave connected to the bus.
3. AS-i LED (red): lit indicates an AS-i power supply error.
4. Bus LED (green): lit indicates that display panel 2 is in BUS display mode (slaves
displayed on the bus).
5. I/O LED (green): lit indicates that display panel 2 is in Slave "SLV" display mode
(displays status of input/output bits for a selected slave).
89
TSX SAY 100
6. Push button "↑↓" designed for local diagnostics of the AS-i bus. You can move
between the different AS-i bus diagnostic modes by pressing this button (long or
quick presses), combined with the "+/-" push button.
7. Push button "+/−" designed for local diagnostics of the AS-i bus. You can move
between the different AS-i diagnostics modes by pressing this button (long or
quick presses), combined with the "↑↓" push button.
8. CANNON SUB D connector for connection to AS-i bus.
90
TSX DM 57 40E 09.2000
TSX SAY 100
Mounting/installation
General
The TSX SAY 100 module can be mounted in any position on the TSX RKY rack,
except for those positions dedicated to processors and power supply.
Note: In the event where the module is mounted on a remote X Bus rack, the maximum allowed distance from the processor must be 175 meters minus the length of
the X Bus (max. 100 m).
Inserting and extracting the module is the same as the general procedure for inserting and extracting modules on Premium PLCs (see the Premium PLC installation
manual.)
Example of mounting a TSX SAY 100 module:
Note: The module can be mounted and removed with both PLC and AS-i bus power switched on.
Number of
modules per
station
TSX DM 57 40E 09.2000
The maximum number of modules per Premium/Atrium PLC station depends on the
type of processor installed:
Processors
Maximum number of AS-i
bus connections
Maximum number of TSX
SAY 100 modules
57-1xx
2
2
57-2xx
4
4
57-3xx/57-4xx
8
8
91
TSX SAY 100
Connections
AS-i bus cables
AS-i bus cables carry the signals and supply the sensors and actuators connected
to the bus with 30 VDC.
Types of AS-i cables:
Cable type
Characteristics
Polarized AS-i ribbon cable
Color: yellow. Wire cross-sec-
Illustration
tion: 1.5 mm2
Standard round cable
(Blue)
(Brown)
(Blue)
(Brown)
Wire cross-section: 1.5 mm2 or
2.5 mm2
Recommended cable: product reference H05VV-F2x1.5, conforms to the DIN VDE
0281standard. Wire cross-section: 1.5 mm2.
Cable routing
The AS-i cable and the power cables carrying higher power levels must be in separate ducts which are protected by a metal screen.
When using a shared route for control cables it is essential that the connections on
these control links should conform to the technology rules (eg. the discharge diode
or limiters on the terminals of self-inductive elements etc.).
Link-up
connector
A set (connector + cover) is delivered with the module, which is used to connect the
module to the AS-i bus. This connector must be linked to the cable of the AS-i bus
and assembled by the user according to the procedure described later.
Illustration:
Connector
92
Cover
TSX DM 57 40E 09.2000
TSX SAY 100
Connection of
module to bus
To connect a module to the bus, follow the procedure below:
1
Connect the 2 wires of the AS-i cable to the connector, taking the polarities into account:
In the special event that a shielded cable is used, this should be connected to the
central terminal.
2 Mount the connector in its cover and fix the cable to it:
3 Click the cover shut:
TSX DM 57 40E 09.2000
93
TSX SAY 100
4 Mount the unit on the module:
94
TSX DM 57 40E 09.2000
TSX SAY 100
Displaying module states
General
This is carried out with 4 LEDs RUN, ERR, COM, I/O which are located on the module. Their state (LED off, flashing or on) provides information on the operating mode
of the module.
LED state:
LEDs
On
Flashing
Off
Module operating normally
Module self-testing (1)
Faulty module, or module switched off
ERR (red) Serious internal fault,
module broken down
Module self-testing (1)
Fault: system OK but:
l application fault or
l AS-i bus error
No internal error
COM
(green)
-
Module self-testing (1) Com- No communication on
munication on AS-i bus
AS-i bus
I/O (red)
Input/output error
Module self-testing (1)
RUN
(green)
Module operating normally
(1) the 4 LEDs flash simultaneously during self-testing mode when the module is
switched on.
TSX DM 57 40E 09.2000
95
TSX SAY 100
Specific display panels on the TSX SAY 100 module
General
3 LEDs: AS-i, Bus and I/O display information specific to the TSX SAY 100 module.
View of the 3 LEDs:
AS-i LED
Bus LED
I/O LED
AS-i display (red)
LED state
Meaning
Module operating normally
LED off
Supply fault on the AS-i bus
LED on
Automatic addressing initialized
Flashing LED
96
TSX DM 57 40E 09.2000
TSX SAY 100
Bus and I/O LEDs
These two LEDs display the view mode selected:
l Bus display mode or
l Slave display mode.
Display module
TSX DM 57 40E 09.2000
LED state
Meaning
Bus LED on, I/O
LED off
The 32 LED display panel located at the
front of the module is in BUS display
mode and displays all the slaves present
on the bus.
Bus LED off, I/O
LED on
The 32 LED display panel located on the
front of the module is in Slave display
mode (SLV) with display of the input/output status for a selected slave.
Bus LED off, I/O
LED off
The 32 LED display panel located on the
front of the module is in Slave display
mode (SLV) with display of the address
of the slave selected.
97
TSX SAY 100
Technical characteristics
AS-i Bus
TSX SAY 100
module
Characteristics
Value
AS-i bus maximum cycle time
5ms
Maximum number of slaves on the AS-i bus
31
Maximum length of AS-i bus (all branches
mixed without relay)
100 meters
Maximum number of inputs/outputs
124 inputs + 124 outputs
Nominal supply voltage for AS-i bus
30 VDC
Characteristics
Value
Programming the TSX SAY 100 module
from PL7 Junior or PL7 Pro software
Response time with 31 slaves (1) for a PLC cy- Typically 27 ms, 37 ms maximum
cle time of 10 ms
Calculation of AS-i scanning time for n slaves
(normal operation)
156 µs x (n+2) if n<31 156 µs x (n+1)
if n=31
PLC current consumed on 5V
Typically 110 mA / 150 mA maximum
AS-i current consumed on 30 V
Typically 50 mA / 60 mA maximum
Dissipated power
2.5 W max.
Protection from polarity inversion on AS-i bus
inputs
Yes
Degree of protection
IP20
Operating temperature
0 to 60 degrees Celsius
AS-i master profile
M2
Standards and service conditions
Conforms to those of Premium PLCs
(see Volume 1)
(1) Logical response time + time between an AS-i input activated on the bus,
processed in the PLC application and applied to an AS-i output.
98
TSX DM 57 40E 09.2000
TSX SAY 100
Personnel safety
General
TSX DM 57 40E 09.2000
To ensure personnel safety it is essential:
l To earth the ground terminal of the PLC.
l To use an AS-i VLSV (very low safety voltage) supply, nominal voltage 30 VDC.
l For PLCs which are connected to an alternating current network, a differentiel circuit breaker must be placed upstream of this network, and this will cut off the PLC
power supply source if ground leakage if detected.
l For PLCs which are connected to a direct current supply source you must ensure
that the supply placed upstream of the PLC is VLVS.
l To use certified AS-i products on the bus.
Due to its type of technology and connection, the TSX SAY 100 module only receives 5 VDC and its 0V is linked to the PLC ground.
99
TSX SAY 100
4.3
Input/output object addressing
Addressing input/output objects
General
Example
Acquisition of inputs and update of slave device outputs connected to the AS-i bus
are carried out automatically. This occurs at the start and end of each cycle respectively of the task in which the TSX SAY 100 module is configured.
The program user has access to these inputs and outputs via the language objects
whose syntax is as follows:
xy.0
\
%
I or Q
Symbol
Type of object
I=input
Q=output
\
Module/channel address
of the TSX SAY 100
x=rack number
y=position number
0=channel 0 of the
module
n
i
.
No. of slave
0 to 31
Rank
of bit
0 to 3
Particular example of rack 0:
%I\2.0\1.3 indicates: input 3 of slave 1, channel 0 of the TSX SAY 100 module, positioned in rack slot 0.
%Q\2.0\31.0 indicates: output 0 of slave 31, channel 0 of the TSX SAY 100 module,
positioned in slot 2 of rack 0.
Illustration:
Addresses
slaves
@1
4E
@3
4S
Slave
0
Addresses
inputs/outputs
of slaves
%I\2.0\1.0
3
0
3
%Q\2.0\3.0
%I\2.0\1.3
%Q\2.0\3.3
AS-i Bus
@5
1S
0
%Q\2.0\5.0
@31
2E & 2S
0
1
0
1
%I\2.0\31.0 %Q\2.0\31.0
%I\2.0\31.1
%Q\2.0\31.1
Note: The physical address of an AS-i slave is programmed by the portable console XZM C11
100
TSX DM 57 40E 09.2000
TSX SAY 100
4.4
AS-i Bus diagnostics
At a Glance
Aim of this
Section
This Section deals with the diagnostics mode carried out by the TSX SAY 100 module.
What’s in this
Section?
This Section contains the following Maps:
TSX DM 57 40E 09.2000
Topic
Page
Introduction to AS-i Bus diagnostics
102
Moving between the different display modes
104
Display of slaves on the AS-i bus
105
Viewing the state of input/output bits for each slave
106
101
TSX SAY 100
Introduction to AS-i Bus diagnostics
General
102
The module display panel is used for:
l Displaying the presence of each slave on the AS-i bus (Bus mode).
l Displaying the state of input/output bits of each slave present on the bus (Slave
mode "SLV").
These modes can be accessed by a combination of actions on the push buttons (↑↓
and +/-) on the TSX SAY 100 module.
Illustration:
TSX DM 57 40E 09.2000
TSX SAY 100
Display modes
Table giving the 2 display modes of the module:
Bus mode
TSX DM 57 40E 09.2000
Slave mode (SLV)
View of AS-i bus image. Each View of selected slave adLED 1 to 31 corresponds to a dress.
slave address on the bus.
l LED on: number of slave
selected.
l LED on: slave present
l flashing LED: slave expected and not detected,
or not expected and detected.
l LED off: slave not expected and not detected.
View of input/output bit state
for slave selected.
l LEDs 0 to 3 display the
state of the input bits.
l LEDs 4 to 7 display the
state of the output bits.
l LED on: bit in state 1.
l LED off: bit in state 0 or
not significant
Illustration:
Illustration:
Illustration:
View mode is displayed with
the Bus LED on and the I/O
LED off.
View mode is displayed by
Bus and I/O LEDs both off.
View mode is displayed by
the Bus LED off and the I/O
LED on.
103
TSX SAY 100
Moving between the different display modes
Illustration
This illustration shows how to move between the different display modes:
Display of image
of the AS-i bus
(default display)
On
Off
Presence
slaves 1 to 31
Hold down
on ↑↓
Number
of slave
Status bits
input
Hold down+/−
Status bits
output
Display of bits
of I/O of the slave
selected
104
Change direction:
Short press on ↑↓
Hold down
on ↑↓
Display of
address of
the selected slave
Change slave:
Short press on +/-
Off
Off
On
Off
TSX DM 57 40E 09.2000
TSX SAY 100
Display of slaves on the AS-i bus
General
This mode is displayed by default when the module is switched on, and is used to
display:
l The expected and detected slaves (LED permanently on).
l The unexpected and undetected slaves (LEDs off).
l The expected and undetected slaves (LEDs flashing).
Illustration:
Display
panels
↑↓
Bus Display
LEDs
showing the
mode
displayed
The image of the AS-i network is displayed on the entire display panel. Each LED
represents an AS-i bus slave address.
You can move between the different modes by a combination of actions on the push
buttons ↑↓ and +/- : see Moving between the different display modes, p. 104.
Two LEDs "Bus" and "I/O" indicate the current display mode.
In the current example, the "BUS" LED is on and the LED "I/O" is off which indicates
that the display is in Bus mode.
In the illustration above, the display panel indicates that:
l Slaves 1, 4, 10 and 20 (LEDs on) are present.
l Slave 11 (flashing LED) is present and not expected, or expected and missing.
TSX DM 57 40E 09.2000
105
TSX SAY 100
Viewing the state of input/output bits for each slave
General
In this mode (Slave "SLV"), the display panel is used to view the state of input/output
bits for each slave present on the bus.
Procedure to be
followed
To access the state of input/output bits for a slave from BUS mode, proceed as follows:
Order Action
Result
1
Press for more than one second on the
button ↑↓
The display switches to Slave "SLV"
mode.
2
Press quickly on the +/- button
The display of the slave address goes
up from 1 to 31.
3
Press quickly on the button ↑↓
The direction of the slave address scan
is reversed.
4
Press quickly on the +/- button
The display of the slave address goes
down from 31 to 1.
5
Pressfor more than one secondon the
button +/−
l
l
LEDs 0 to 3 display the state of input
bits for the slave selected (1).
LEDs 4 to 7 display the state of output
bits for the slave selected (1).
6
Press quickly on the +/- button
The state of inputs-outputs for the following slave is displayed.
7
Press quickly on the button ↑↓
The direction of the slave address scan
is reversed.
8
Press quickly on the +/- button
The state of input-outputs for the previous slave is displayed.
9
Pressfor more than one second on the
button +/−
The display shows again the number of
slave selected.
(1)
LED on = bit on state 1
LED off = bit on state 0 or no input or output
106
TSX DM 57 40E 09.2000
TSX SAY 100
Illustration
Slave Number
(example: 10)
State of bits (example:
%I\2.0\10.0 et %I\2.0\10.1=1)
↑↓
Change direction:
Short press on ↑↓
Change slave:
Short press on +/−
Slave Display
TSX DM 57 40E 09.2000
Status of output bits
(example: %Q\2.0\10.2 and
%Q\2.0\10.3=1
Channel Display
107
TSX SAY 100
4.5
Operating modes of the TSX SAY 100 module
Operating modes of the TSX SAY 100 module
General
For more information, refer to the section on AS-i installation in the Premium PLCs
Applications Manual - Basic Applications, Volume 1.
Output fallback
position
The fallback mode is set in the configuration screen (see Premium PLCs Applications Manual) and can be read in the word %KWxy.0.19:X0:
l %Kwxy.0.19:X0 = 1: fallback to 0
l %KWxy.0.19:X0 = 0: maintain state
(x = rack address, y = module address)
Operation:
When the AS-i channel changes to STOP:
l With fallback to 0 option: outputs are forced to 0, then communication stops on
the medium.
l With maintain state option: outputs are maintained, then communication stops
on the medium.
Automatic slave
addressing
When this function is enabled in the module configuration, it allows the replacement
of a faulty slave with a slave of the same type without stopping the AS-i bus, and
without the need for special action:
l If the replacement slave is programmed with the same address and has the same
profile, it will be automatically inserted in the list of slaves detected, then activated. If this is not the case, the ERR and AS-i LEDs will flash simultaneously.
l If the new slave has never been used (address 0, new slave) and has the same
profile, the slave automatically takes on the address of the replaced slave and is
therefore in the list of detected slaves and the list of active slaves. If this is not the
case, the ERR and AS-i LEDs will flash simultaneously.
These actions are only possible if one and only one slave is faulty in the configuration.
Processor error
If there is a communication break with the processor, the module switches to SAFETY position.
Communication breaks are caused by the following:
l Triggering of the processor watchdog if the TSX SAY 100 module is positioned
in the rack supporting the processor.
l Disconnection of the X Bus cable if the TSX SAY 100 module is positioned in an
extension rack.
108
TSX DM 57 40E 09.2000
TSX SAY 100
Module fault
In the event of a serious fault on the TSX SAY 100 module (faulty component, etc.)
the module stops communicating with the X Bus and with the AS-i Bus. The same
type of behavior occurs when a module is removed with the power on.
Removing a
module with
power switched
on
Should a module be removed with the power switched on, communication with the
X Bus stops and the processor indicates a module fault.
Communication with the AS-i bus is also interrupted without notice. In this case, the
slaves with a watchdog set their outputs in the desired state, and the others remain
in position and cannot be set to 0 since the module cannot guarantee communication.
Inserting a
module with
power switched
on
After switching on the TSX SAY 100 module, it waits to receive configuration from
the processor or for one of the push buttons ↑↓ or +/- to be pressed, otherwise it remains at a stop.
AS-i supply fault
When an AS-i supply module fault occurs, communication stops with:
l Slaves with a watchdog positioning their outputs in the desired state, except if the
slave takes its power from the AS-i.
l Slave commands switch to 0 due to lack of power.
This fault is indicated by the AS-i LED.
Break in the AS-i
medium
There are several ways in which a break in the medium can occur:
1. There is a break in the medium as it exits the module:
Behavior is the same as that for a power outage, with all slaves disappearing and
a supply fault being indicated.
2. There is a break in the medium after the TSX SAY 100 module and the AS-i supply:
All slaves disappear and no indication of supply fault.
3. There is a break in the medium after the TSX SAY 100 module, the AS-i supply
and some slaves:
Slaves located after the break disappear and no indication of supply fault.
TSX DM 57 40E 09.2000
109
TSX SAY 100
4.6
Precautions of use
At a Glance
Aim of this
Section
This Section deals with the precautions to be taken when installing an AS-i bus.
What’s in this
Section?
This Section contains the following Maps:
110
Topic
Page
24 V auxiliary supply
111
Multiple addressing
112
TSX DM 57 40E 09.2000
TSX SAY 100
24 V auxiliary supply
Recommendations
TSX DM 57 40E 09.2000
When slaves use a 24 V auxiliary supply, the disappearance of this supply is not
managed by the TSX SAY 100 module.
Information on the disappearance of this supply can be accessed by using a 24 V
input.
111
TSX SAY 100
Multiple addressing
Recommendations
When one or more slaves are connected, make sure that you do not assign an address which is already being used by a slave on the bus.
If slave address is doubled then two scenarios may occur:
1. The two slaves with identical addresses have the same profile and manage identical I/Os: the AS-i master bus does not detect any error.
2. The two slaves with identical addresses manage different I/Os: the AS-i master
bus can detect transmission errors when accessing the I/O from one of the two
slaves.
112
TSX DM 57 40E 09.2000
Communication: module
TSX SCY 21601 and PCMCIA
cards
IV
At a Glance
Aim of this Part
This Part deals with installing hardware for the TSX SCY 21601 communication
module and PCMCIA communication cards.
What’s in this
part?
This Part contains the following Chapters:
TSX DM 57 40E 09.2000
Chapter
Chaptername
Page
5
At a Glance
115
6
Installing the TSX SCY 21601 module
119
7
Installing PCMCIA cards
145
113
TSX SCY 21601
114
TSX DM 57 40E 09.2000
At a Glance
5
At a Glance
Aim of this
Chapter
This Chapter deals with the general features on the TSX SCY 21601 module and
PCMCIA communication cards.
What’s in this
Chapter?
This Chapter contains the following Maps:
TSX DM 57 40E 09.2000
Topic
Page
General communication architecture
116
Operating standards
117
115
At a Glance
General communication architecture
General
116
Illustration:
TSX DM 57 40E 09.2000
At a Glance
Operating standards
General
TSX DM 57 40E 09.2000
TSX SCY 21601 and PCMCIA module communication cards comply with the following international norms and standards:
l US Standards: UL508, IEC 1131-2
l CANADA Standards: CSA C22.2/1 42
l Compliance with rule: FCC-B
l EC labeling
l PCMCIA mechanical standard type III E
l PCMCIA 2.01
The link built into the TSX SCY 21601 module complies with communication standards:
l UNI-TELWAY
l Modbus
l XWAY
The TSX FPP 20 PCMCIA FIPWAY card and TSX FFP 10 FIPIO agent comply with
communication standards:
l FIP protocol (link, network management)
l PCMCIA
l XWAY
TSX SCP 111, 112, 114 PCMCIA cards comply with communication standards:
l UNI-TELWAY protocols, Modbus
l PCMCIA
l XWAY
117
At a Glance
118
TSX DM 57 40E 09.2000
Installing the TSX SCY 21601
module
6
At a Glance
Aim of this
Chapter
This Chapter deals with installing the hardware for the TSX SCY 21601 module.
What’s in this
Chapter?
This Chapter contains the following Sections:
TSX DM 57 40E 09.2000
Section
Topic
Page
6.1
At a Glance
120
6.2
Description
121
6.3
Characteristics of the integrated channel
123
6.4
Compatibility of reception channel
124
6.5
Installation
125
6.6
Operation
127
6.7
Visual diagnostics of the module
128
6.8
Connecting the built-in channel
130
119
TSX SCY 21601
6.1
At a Glance
At a Glance
General
The TSX SCY 21601 communication module is used to house PCMCIA communication cards.
It comprises two communication channels:
l A built-in channel (channel 0) multi-protocol, insulated RS485 asynchronous series link, supporting UNI-TELWAY, Jbus/Modbus or Character Mode protocols.
l A PCMCIA reception channel (channel 1) can support the following protocols:
l UNI-TELWAY, Jbus/Modbus and Character Mode on a RS 232-D link, Current
loop or RS 485 corresponding to cards TSX SCP 111, 112 and 114.
l FIPWAY cellular network corresponding to the TSX FPP 20 card.
Note: Important: The TSX SCY 21601 module is only compatible with a twin-wire
RS 485 link.
Note: The TSX SCY 21601 communication module is only compatible with Premium/Atrium type processors with software version SV ≥3.0 (indicated on the side label of the processor module).
120
TSX DM 57 40E 09.2000
TSX SCY 21601
6.2
Description
Description
General
The TSX SCY 21601 module is a single (half-size) module which can be inserted
into one of the slots of a Premium/Atrium PLC station rack.
Note: X Bus offset is not authorized for this module.
This module is made up of the following elements:
1. Three signaling LEDs on the front of the Illustration:
module:
l RUN and ERR indicate the state of
the module.
l CH0 displays the state of communication of the built-in series link channel
(channel 0).
2. Built-in channel with a 25-pin SUB-D female connector, base link RS 485 in half
duplex mode (channel 0):
l UNI-TELWAY
l Jbus/Modbus
l Character Mode
3. PCMCIA card reception channel type III
(channel 1).
TSX DM 57 40E 09.2000
Channel 0:
integrated
channel
Channel 1:
reception
channel
121
TSX SCY 21601
Insertable cards
122
Different types of communication cards, which can be inserted into the TSX SCY
21601module reception channel:
Type
Description
TSX SCP 111
Multi-protocol cards (UNI-TELWAY, Modbus/Jbus,
Character Mode), RS 232 D, 9 non-insulated signals.
TSX SCP 112
Multi-protocol cards (UNI-TELWAY, Modbus/Jbus,
Character Mode), current loop (CL 20 mA).
TSX SCP 114
Multi-protocol cards (UNI-TELWAY, Modbus/Jbus,
Character Mode), RS 485 D, insulated RS 422 compatible.
TSX FPP 20
FIPWAY network cards
Illustration
TSX DM 57 40E 09.2000
TSX SCY 21601
6.3
Characteristics of the integrated channel
Characteristics of the integrated channel
General
The TSX SCY 21601module integrated channel includes:
l An RS 485 physical interface.
l A medium double twisted pair.
l UNI-TELWAY, Modbus and Character Mode protocols.
Characteristics
Characteristics of the integrated channel for the 3 protocols:
TSX DM 57 40E 09.2000
UNI-TELWAY
Modbus
Character Mode
Type
Master-slave
Master-slave
Half duplex
Flow
9600 bits/sec. Parameterized from
1200 to 19200 bits/
sec.
9600 bits/sec. Parameterized from
1200 to 19200 bits/
sec.
9600 bits/sec. Parameterized from
1200 to 19200 bits/
sec.
Number of devices
28
28
-
Number of slave addresses
98
98
-
Length of bus without 1000 m
branch
1000 m
1000 m
Size of messages
240 bytes
256 bytes
4 Kb
Services
Master-slave message Slave-slave
UNI-TE Requests
Reading of Words/
Character string
bits Writing of Words/ transmission Characbits Diagnostics
ter string reception
123
TSX SCY 21601
6.4
Compatibility of reception channel
Compatibility of the reception channel
General
The cards supported by the reception channel are:
l PCMCIA cards: TSX SCP 111, 112, 114 which ensure communication with Premium./Atrium PLCs, Series 1000, Modicon and other UNI-TELWAY, Jbus/Modicon and Character Mode compatible products. PCMCIA cards are also Jbus/
Modbus compatible with Series 1000 PLCs.
l The TSX FPP 20 card is compatible with FIPWAY devices:
l Model 40 PLCs (TSX 47-455, TSX 67-455etc.) of a version higher than 5.0.
l TSX 17 PLCs
l Compatible PCs connected with TSX FPC10 and TSX FPC 20 cards.
Note: The TSX FPP 10 card is not supported by the reception channel.
124
TSX DM 57 40E 09.2000
TSX SCY 21601
6.5
Installation
Installation
General
The TSX SCY 21601 module is installed in a Premium/Atrium PLC station rack.
It is included in an X-WAY network architecture based on Series 7, Micro, Premium
and Atrium PLCs.
This communication module accords the PLC station the following:
l An insulated RS 485 multiprotocol communication channel.
l A slot for PCMCIA standard communication card.
The TSX SCY 21601 module can be fixed in any available slot in a Premium/Atrium
PLC station rack.
Maximum
number
The TSX SCY 21601 module supports a maximum of 2 application-specific communication channels, an RS 485 channel built into the module and a channel outlet for
the PCMCIA card to be inserted into the module.
Since the maximum number of channels managed by a PLC station depends on the
type of processor installed, the number of TSX SCY 21601 modules in a station will
therefore depend on:
l The type of processor installed.
l The number of channels already in use, apart from those being used for communication.
The user will therefore have to count the total number of channels in use on the PLC
station and determine the number of TSX SCY 21601 modules which can be used.
Note: How to count the communication channels is described in the Premium PLC
Installation Manual.
Reminder of the number of application-specific channels managed by each processor type:
TSX DM 57 40E 09.2000
Processors
Number of applicationspecific channels
TSX P57103/TSX P57153
8
TSX P57203/TSX P57253 - PCX 57203
24
TSX P303/TSX P57353 - PCX 57353
32
TSX P57453
64
125
TSX SCY 21601
Wiring/Unwiring
The TSX SCY 21601 module can be wired or unwired when switched on. This
device does not have a backup memory function. When the module is disconnected
from the rack, its internal memory is erased. The module re-initializes when it is reconnected.
It is possible to unwire a TSX SCY 21601 module with a PCMCIA card while it is
switched on.
Note: In contrast, PCMCIA cards cannot be removed when switched on.
126
TSX DM 57 40E 09.2000
TSX SCY 21601
6.6
Operation
Operation
General
TSX DM 57 40E 09.2000
The TSX SCY 21601 module manages two independent communication channels,
of which each has its own functionalities:
l Channel 0 deals with UNI-TELWAY, Jbus/Modbus and Character Mode protocols on an isolated physical link, and with standardized RS 485 half duplex with
a speed limited to 19200 bits per second.
l Channel 1 receives one of the following PCMCIA communication cards:
l Field bus: Cards TSX SCP 111 (RS232), TSX SCP 112 (current loop), TSX
SCP 114 (RS 422/RS 485) UNI-TELWAY, Jbus/Modbus and Character Mode.
l Cellular network: FIPWAYTSX FPP 20 card.
The PCMCIA card and protocol is selected during configuration of TSX SCY 21601
communication channels via PL7 Junior and PL7 Pro software.
127
TSX SCY 21601
6.7
Visual diagnostics of the module
Visual diagnostics of the module
General
Three LEDs are placed on the front panel of TSX SCY 21601 modules. These LEDs
are used to display information on the operating state of the module and on the
state of communication of the built-in series link channel.
Illustration:
RUN (green)
ERR (red)
CH0 (yellow)
The state of communication of the reception channel is shown by the ERR and COM
LEDs for the PCMCIA card series link or FIPWAY (See Visual diagnostics of PCMCIA cards, p. 158)
Meaning of LEDs:
RUN
ERR
CH0
Comments
(1)
(1)
Module switched off or module inoperative
No communication on the built-in channel
Communication on the built-in channel
(2)
(1)
Off
On
Serious error on the built-in channel
Flashing, (1) = Indifferent state, (2) = Display of line
activity
128
TSX DM 57 40E 09.2000
TSX SCY 21601
RUN
ERR
CH0
Comments
Error on the built-in channel Configuration Error
No Device OK on the channel
Device error on the built-in channel
Self-tests in progress
Off
On
Flashing, (1) = Indifferent state, (2) = Display of line
activity
TSX DM 57 40E 09.2000
129
TSX SCY 21601
6.8
Connecting the built-in channel
At a Glance
Aim of this
Section
This Section describes the different methods of connecting the built-in channel of the
TSX SCY 21601 module
What’s in this
Section?
This Section contains the following Maps:
130
Topic
Page
At a Glance
131
Connection to UNI-TELWAY bus
132
Reminder on adapting the line distributed over RS 485
134
Example of UNI-TELWAY architecture
136
Connecting to the Jbus/Modbus field bus
137
Reminder on single line polarization in RS 485
138
Example of Modbus architecture
140
Connecting the TSX SCA 50 device
141
Connection in Character Mode
142
Consumption of the TSX SCY 21601 module
143
TSX DM 57 40E 09.2000
TSX SCY 21601
At a Glance
General
The wiring accessories designed for connection of the TSX SCY 21601 module RS
485 base link allow the following connections:
l Connection to UNI-TELWAY network via a TSX SCA 50 device using a TSX SCY
CU6030 cable or via a TSX SCA 62 device using a TSX SCY CU 6530 cable.
l Connection to Jbus/Modbus network via a TSX SCA 50 device using a TSX SCY
CM 6530 cable.
l Connection to RS 485 standard devices using a connector adapted to the link,
using a TSX SCY CU 6030 or TSX SCY CM 6030 cable.
Illustration:
TSX SCY 21601
TSX SCY CU6030 cable for UNI-TELWAY
TSX SCY CM 6030 cable for Jbus/Modbus
Built in RS 485 channel
TSX SCY CU 6530 cable
for UNI-TELWAY
TSX DM 57 40E 09.2000
131
TSX SCY 21601
Connection to UNI-TELWAY bus
General
The communication channel built into the module is connected by the TSX SCY CU
6030 connection cable to the UNI-TELWAY field bus, via the TSX SCA 50 connection device.
Illustration:
25-pin SUB-D connector
UNI-TELWAY cable: TSX SCY CU 6030
UNI-TELWAY cable: TSX SCY CU 6530
Description of
cables
TSX SCY CU 6030 cable:
TSX SCA 50 connection unit
Red
White
White
Blue
132
TSX DM 57 40E 09.2000
TSX SCY 21601
TSX SCY CU 6530 cable:
TSX SCA 62 connection unit
15-pin SUB-D connector
TSX DM 57 40E 09.2000
133
TSX SCY 21601
Reminder on adapting the line distributed over RS 485
General
This is the adaptation used for UNI-TELWAY type networks.
General architecture diagram of a UNI-TELWAY network:
Zc
Connecting
network stations
134
Zc
The network is made up of a single shielded twisted pair. The different network stations are connected in the following way:
1
Connect all outputs marked + (Tx+, Rx+) to the network wire marked: L+.
2
Connect all outputs marked + (Tx-, Rx-) to the network wire marked: L-
3
Adapt the impedance of the network to the average of the two adaptation elements
(Zc) located on the two end stations of the network.
4
For each station, connect the wire L+ to 5 V and the wire L- to 0 V via the two polarization resistances (Rp = 4.7 KΩ) to achieve polarization distributed over the
network. This polarization maintains the idle network in a stable state.
TSX DM 57 40E 09.2000
TSX SCY 21601
Essential
characteristics
TSX DM 57 40E 09.2000
The essential characteristics are:
l Up to 32 stations
l Maximum range: About 1300 m
l Bus topology
l Branch ≤ 15 m
l Half duplex on 2 wires
l End of line adaptation on the end-stations
l Adaptation of distributed line Rp = 4.7 KΩ
135
TSX SCY 21601
Example of UNI-TELWAY architecture
Example
136
TSX DM 57 40E 09.2000
TSX SCY 21601
Connecting to the Jbus/Modbus field bus
General
The built-in channel is connected to the bus via the TSX SCA 50 device, using the
TSX SCY CM 6030 connection cable.
Illustration:
Integrated channel equipped with a
25-pin SUB-D connector
Jbus/Modbus cable: TSX SCY CM 6030
Description of
lead
Description of the TSX SCY CM 6030 lead
Green/White
White/Green
Orange/White
White/Orange
D(A)
D(B)
White/Blue
Blue/White
TSX DM 57 40E 09.2000
137
TSX SCY 21601
Reminder on single line polarization in RS 485
General
Single line polarization is the polarization used for Modbus type networks.
General architecture diagram of a RS 485 network:
The senders are symbolized by:
The receivers are symbolized by:
138
TSX DM 57 40E 09.2000
TSX SCY 21601
Connecting
network stations
The network is made up of a single shielded twisted pair. The different network stations are connected in the following way:
1
Essential
characteristics
TSX DM 57 40E 09.2000
Connect all outputs marked + (Tx+, Rx+) to the network wire marked: L+.
2
Connect all outputs marked + (Tx-, Rx-) to the network wire marked: L-
3
Adapt the impedance of the network to the average of the two adaptation elements
(Rc) located on the two end stations of the network.
4
For each station, connect the wire L+ to 5 V and the wire L- to 0.V via the two polarization resistances (Rp = 470 Ω) to achieve distributed polarization of the network.
This polarization continuously circulates a current in the network.
Adaptation can be anywhere on the network (in practice it is generally done at
master level).
There must be single polarization for the entire network, whatever its range.
The essential characteristics are:
l Up to 32 stations
l Maximum range: About 1300 m
l Bus topology
l Branch ≤ 15 m
l Half duplex on 2 wires
l End of line adaptation on the end-stations
l Adaptation of distributed line Rp = 470 Ω
139
TSX SCY 21601
Example of Modbus architecture
Example
140
TSX DM 57 40E 09.2000
TSX SCY 21601
Connecting the TSX SCA 50 device
Modbus without
line adaptation
Illustration:
TSX SCY CM 6030 cable
TSX SCA 50
nc
nc
Orange/White
White/Orange
D(A)
D(B)
nc
nc
Modbus with line
adaptation
Illustration:
TSX SCY CM 6030 cable
Green/White
White/Green
TSX SCA 50
Orange/White
White/Orange
White/Blue
Blue/White
TSX DM 57 40E 09.2000
141
TSX SCY 21601
Connection in Character Mode
General
The connection cable of the TSX SCY 21601 module to the RS 485 standard is a
TSX SCY CM 6030 cable.
To connect from the built-in channel of the TSX SCY 21601 in Character mode to a
Half duplex RS 485 standard device, the user creates the link by using a TSX SCY
CM 6030 connection cable. An connector adapted to the device for connection
must be added to the free end of the cable, and the necessary signals must be
connected (see cable wiring in Connecting the TSX SCA 50 device, p. 141.
Illustration:
TSX SCY CM 6030 cable
142
RS 485 device
two wires
TSX DM 57 40E 09.2000
TSX SCY 21601
Consumption of the TSX SCY 21601 module
Values
TSX DM 57 40E 09.2000
This table shows the consumption of a TSX SCY 21601 communication module
without PCMCIA card nor connection to the built-in channel:
Voltage
Typical current
Maximum current
Dissipated power
5 Volts
350 mA
420 mA
2.1 W max.
143
TSX SCY 21601
144
TSX DM 57 40E 09.2000
Installing PCMCIA cards
7
At a Glance
Aim of this
Chapter
This Chapter deals with the hardware installation of PCMCIA communication cards
onto Premium/Atrium PLCs.
What’s in this
Chapter?
This Chapter contains the following Sections:
TSX DM 57 40E 09.2000
Section
Topic
Page
7.1
At a Glance
146
7.2
Description
149
7.3
Connecting the PCMCIA card reception channel
151
7.4
Connection of TSX SCP 111 card
161
7.5
Connection of the TSX SCP 112 card
164
7.6
Connection of the TSX SCP 114 card
178
7.7
Connection of the TSX FPP 20 card
187
7.8
Connection of the TSX FPP 10 card
188
7.9
Connection of the TSX MBP 100 card
189
7.10
Summary of connection devices
196
7.11
Precautions when connecting PCMCIA cards
198
7.12
Consumption of PCMCIA cards
199
145
PCMCIA installation
7.1
At a Glance
At a Glance
General
Premium/Atrium PLC stations connect to communication networks, buses and links
through PCMCIA communication cards.
The card to be connected is a metal device whose dimensions comply with PCMCIA
extended type III.
PCMCIA cards are installed in the reception slot of the processor and/or
TSX SCY 21601 module in PLCs from the Premium family.
PCMCIA cards can also be used in devices which have type III reception, such as
CCX 17, FT 2100 terminals or PC-compatible third-party devices, for example.
Illustration:
Micro
Premium
Premium
Atrium
Note: It is prohibited to connect PCMCIA cards when the power is switched on.
PCMCIA cards are installed, operated and maintained using PL7 Junior/PL7 Pro
programming and operation software for all PLCs in the Premium family.
146
TSX DM 57 40E 09.2000
PCMCIA installation
TSX SCP 11
cards
Series link PCMCIA cards.
Each TSX SCP 111, 112, 114 PCMCIA card supports a different physical layer. This
family comprises three products:
Product reference
Physical layer
TSX SCP 111
RS 232-D link.
Illustration
TSX SCP 112
Current loop link (20 mA).
TSX SCP 114
RS 485 link (RS 422 compatible)
All three cards, TSX SCP 111, 112 and 114, support the following communication
protocols:
l Modbus/Jbus protocol
l UNI-TELWAY protocol
l Character Mode asynchronous link
TSX FFP 20 card
FIPWAY network PCMCIA card:
Functions
Illustration
The TSX FPP 20 PCMCIA card supports the FIP
physical layer. It is used to connect a Premium/
Atrium station to a FIPWAY network, as well as to
connect to devices of manufacturers who wish to
connect their products to the FIPWAY network.
The card is fitted with four rotary switches (marked
"1" in the illustration) which make it possible to encode the network number and station.
TSX DM 57 40E 09.2000
147
PCMCIA installation
TSX MBP 100
card
Modbus + network PCMCIA card:
Functions
Illustration
The TSX MPB 100 PCMCIA card is used to connect a Premium/Atrium PLC station to the Modbus+ network.
TSX FPP 10 card
FIPIO bus agent PCMCIA card:
Functions
Illustration
The TSX FPP 10 PCMCIA card is used to connect a Premium/Atrium PLC station to a FIPIO
bus.
It ensures the link with TSX 47-107 PLCs and
April 5000
148
TSX DM 57 40E 09.2000
PCMCIA installation
7.2
Description
Description
General
PCMCIA type III (extended) communication cards are built into a metal device with
the following dimensions:
l Length: 85.5 mm
l Width: 51 mm
l Height: 10 mm
The front of the card is designed to display the functioning of communications as
well as the physical connection to the network.
Mechanical
configuration
The mechanical configuration of the card must be adapted by mounting a removable
cover, depending on the type of installation desired:
Type of installation
Configuration
Installation on a Premium type processor or on
a TSX SCY 21601 communication module.
Removable cover with
wings. Screws are provided to fix it to the reception
module (marked 3 on illustration)
Illustration
Installation on an Atrium Removable cover with
type processor.
wings. Screws are provided to fix it to the Atrium
processor (marked 2 on
illustration).
Installation onto a PC
compatible device.
Removable cover
(marked 1 on illustration).
Note: The covers with wings, mounted on PCMCIA cards, prevent any accidental
removal when switched on and guarantee that the card remains in good working
order.
The two covers (1) and (3) are provided with the PCMCIA card. Cover (2) is provided with the Atrium processor.
TSX DM 57 40E 09.2000
149
PCMCIA installation
Connection to the network is achieved by connecting the linking cable to the front of
the card. A guidance system is used to prevent anything being mounted incorrectly.
The product reference label informs the user of the type of physical layer supported
by the card.
150
TSX DM 57 40E 09.2000
PCMCIA installation
7.3
Connecting the PCMCIA card reception channel
At a Glance
Aim of this
Section
This Section describes the installation of PCMCIA cards in the reception channel of
the TSX SCY 21601 module.
What’s in this
Section?
This Section contains the following Maps:
TSX DM 57 40E 09.2000
Topic
Page
Precautions when connecting PCMCIA
152
Connecting PCMCIA cards
153
Product references for PCMCIA cards and installation
154
Mounting cards and cables
155
PCMCIA card operation display
157
Visual diagnostics of PCMCIA cards
158
151
PCMCIA installation
Precautions when connecting PCMCIA
General
CAUTION
The PCMCIA card must be handled with the power switched off
Failure to observe this precaution can result in injury or equipment damage.
When removing or inserting the card, the unit is not guaranteed to be operational.
There is no procedure for a warm start between the PCMCIA card and the TSX SCY
21601 reception device.
In the event that the operating environment does not allow the application to be
stopped by switching off the PLC processor, you are recommended to remove the
TSX SCY 21601 module with the PCMCIA card.
The PCMCIA card must be equipped with a PLC version cover and be screwed in
the TSX SCY 21601 reception module before the unit is switched on (see Mechanical configuration, p. 149).
152
TSX DM 57 40E 09.2000
PCMCIA installation
Connecting PCMCIA cards
General
Connecting PCMCIA cards requires specific cables and connection devices, depending on the type of models.
Series link cards
Product references of cables and branch devices to be used with series link PCMCIA cards according to the different protocols:
PCMCIA card
UNI-TELWAY
Jbus/Modbus
Character Mode
TSX SCP 111 (RS
232)
TSX SCP CD 1030/1100 in
point to point mode
TSX SCP CD 1030/1100 in
point to point mode
TSX SCP CD 1030/1100
TSX SCP CC 1030 in multidrop mode via a modem
TSX SCP CC 1030 in multidrop mode via a modem
TSX SCP 112 (Current Loop
TSX SCP CX 2030
TSX SCP CX 2030
TSX SCP CX 2030
TSX SCP 114 (RS
422/RS 485
TSX SCP CU 4030 and TSX
SCA 50
TSX SCP CM 4030 and TSX
SCA 50
TSX SCP CU 4030 and TSX
SCP CM 4030
FIPWAY network
card
The TSX FPP 20 FIPWAY card is connected via the reception channel using a TSX
FPCG 10 or TSX FPCG 30 cable.
Modbus+ Card
The TSX MBP 100 Modbus+ card is connected via the reception channel using a
TSX MBP CE 030 (3 m) or TSX MBP CE 060 (6 m).
TSX DM 57 40E 09.2000
153
PCMCIA installation
Product references for PCMCIA cards and installation
Installation
Table showing options for installing PCMCIA cards in processor reception channels
and in the TSX SCM 21601module:
Product references Processor reception channel TSX SCM 21601 reception channel
Applicationspecific
channels and
network
connections
TSX SCP 111
Yes
Yes
TSX SCP 112
Yes
Yes
TSX SCP 114
Yes
Yes
TSX FPP 10
Yes
No
TSX FPP 20
Yes
Yes
TSX MBP 100
Yes
No
Table showing the number of application-specific channels or network connections
used by PCMCIA cards:
Product references Number of application-specific channels
Card in the processor
Card in the TSX SCM
21601 module
Number of
Network
Connections
TSX SCP 111
0
1
-
TSX SCP 112
0
1
-
TSX SCP 114
0
1
-
TSX FPP 10
0
-
-
TSX FPP 20
-
-
1
TSX MBP 100
-
-
1
Reminder of the number of application-specific channels and network connections
managed by the type of processor:
154
Processors
Applicationspecific channels
Network connections
TSX P57103/TSX P57153
8
2
TSX P57203/TSX P57253 - PCX 57203
24
4
TSX P303/TSX P57353 - PCX 57353
32
8
TSX P57453
64
8
TSX DM 57 40E 09.2000
PCMCIA installation
Mounting cards and cables
Details about
PCMCIA cards
Illustration:
PCMCIA cards are made up of the following elements:
TSX DM 57 40E 09.2000
Number Designation
Comments
1
Equipped card
Receives electronic components.
2
Body made of zamac
-
3
PCMCIA connector
Connector with 20 connection points.
4
Upper cover
Houses the product reference label which shows
the type of PCMCIA card
5
Removable cover
Ensures the card is displayed in its slot. The
names of the two LEDs are printed on the front of
the removable cover. This cover is also used to
fix the PCMCIA card on the processor or on the
TSX SCM 21601 module.
6
Linking cable with ferule
The ferule placed on the end of the PCMCIA card
cable side prevents the cable being pinched by
the removable cover. This ferule also eliminates
the risk of causing a bending radius which can
damage the quality of the link.
155
PCMCIA installation
Assembly
To assemble the transmission support for the card first remove the cover which is
screwed on the device then follow the instructions below:
Step
156
Instruction
1
Connect the cable
2
Place the appropriate cover
on the device, taking care to
insert the ferule in the slot
provided in order to fix the cable to the card.
3
Screw on the cover
4
Insert the card in the slot provided in the host device.
5
Screw in the card to stop it
being moved when switched
on, and to ensure it functions
effectively.
Illustration
Receptor
Processor
or
TSX SCM 21601
TSX DM 57 40E 09.2000
PCMCIA installation
PCMCIA card operation display
General
Two diagnostics LEDs are located on the front of the card. They inform the user on
how exchanges between the device supporting the PCMCIA card and the related
device are functioning.
Illustration
Number Description
TSX DM 57 40E 09.2000
1
Error "ERR" LED (normally off) displays errors.
This is red
2
The "COM" communication LED displays
the line activity.
This LED is:
l Yellow on the TSX SCP 111-112-114,
TSX FPP 10 and TSX FPP 20 cards.
l Green on the TSX MBP 100 card.
Diagram
157
PCMCIA installation
Visual diagnostics of PCMCIA cards
General
Depending on their state, LEDs of the PCMCIA card indicate the operating mode for
communication, as well as the card diagnostics.
Cards TSX SCP
111/112/114 and
TSX FPP 10/20
State of LEDs:
ERR
COM
(1)
Key:
Off
Meaning
Corrective actions
Device switched off No dialog
Check supply, Card inoperational
Operating normally
-
Serious error
Change the card
Functional error
Check the configuration and the
connection to the communication bus
Functional error
Check the configuration
On
Flashing
(1) = Indifferent state
Note: The "ERR" LED of the card TSX FPP 20, when flashing, indicates that an
external error has appeared. These errors are:
l Line error
l Station already present on the network
l Incorrect station-network address coding (rotary switch coding)
158
TSX DM 57 40E 09.2000
PCMCIA installation
TSX MBP 100
cards
State of LEDs:
ERR
COM
Meaning
Corrective actions
Device switched off No dialog
Check supply, Card inoperational
Operating normally
-
Serious error
Change the card
Functional error: Card not configured, communication cannot
start on the network.
Configure the card using: PL7
Junior or PL7 Pro
Functional error
Check the configuration and the
connection to the Modbus+ network. The way the COM LED
flashes indicates the type of
problem (see below)
(1)
(2)
Off
On
Flashing
(1) = The way the COM LED flashes indicates the operating state of the network (see
below) - (2) = Indifferent state
Meaning of COM LED flashing:
TSX DM 57 40E 09.2000
State of COM LED
Meaning
6 flashes/second
Node is functioning normally It receives and transmits the network token. All the nodes on a network which are functioning
flash in this way.
1 flash/second
The node is off-line just after power up or after leaving the 4
flashes/sec. mode. In this state, the node monitors the network and establishes a table of active nodes. After remaining
in this state for 5 seconds, the node attempts to switch to a
normal operating state, indicated by 6 flashes per second.
159
PCMCIA installation
State of COM LED
Meaning
2 flashes, followed by a 2
second pause
The node detects the token transmitted among the other
nodes, but never receives the token. Check if there is an open
circuit or a faulty terminator on the network.
3 flashes, followed by a 1.7 The node does not detect any token transmitted among the
second pause
other nodes. It regularly searches for the token but cannot find
another node to pass the token to it. Check if there is an open
circuit or a faulty terminator on the network.
4 flashes, followed by a 1.4 The node has detected a valid node message using a network
second pause
address identical to its own address. The node remains in this
state for as long as it continues to detect the duplicated address. If the duplicated address has not been detected within
5 seconds, the node changes mode and flashes once per second.
160
TSX DM 57 40E 09.2000
PCMCIA installation
7.4
Connection of TSX SCP 111 card
At a Glance
Aim of this
Section
This Section deals with installing hardware for TSX SCP 111 PCMCIA cards.
What’s in this
Section?
This Section contains the following Maps:
TSX DM 57 40E 09.2000
Topic
Page
Point to point connection in Character Mode (DTE <==> DTE)
162
UNI-TELWAY, Modbus or Character Mode via Modem
163
161
PCMCIA installation
Point to point connection in Character Mode (DTE <==> DTE)
General
The TSX SCP 111 RS 232 D physical support card is inserted either in the processor
or in the TSX SCY 21601 module. It is connected to the related device with the TSX
SCP CD 1030/1100 cable.
The devices to be connected are DTE to DTE (Data Terminal Equipment ). For example: terminal, printer, etc.
Illustration:
TSX SCP 111
Printer
TSX SCP CD 1030 (length 3 m)
or TSX SCP CD 1100 (length 10 m)
Description of
TSX SCP CD
1030 cable
Illustration:
The PCMCIA 20-pin mini-connector
supports the signals:
Blue/white rings
White/blue rings
White/orange rings
Orange/white rings
Green/white rings
White/green rings
162
TSX DM 57 40E 09.2000
PCMCIA installation
UNI-TELWAY, Modbus or Character Mode via Modem
General
The PCMCIA card is connected to a UNI-TELWAY, Modbus or Character Mode bus,
via a modem and a telephone link (DTE/DCE type), using a TSX SCP CC 1030 cable.
The connected devices are DCE type, for example a modem or a converter.
Illustration:
TSX SCP 111
Modem
TSX SCP CC 1030 (length 3 m)
Description of
the TSX SCP CC
1030 cable
Illustration:
The PCMCIA 20-pin mini-connector
supports the signals:
Connector
SUB-D 25M
White/blue rings
Blue/white rings
White/orange rings
Orange/white rings
White/green rings
Green/white rings
White/brown rings
Brown/white rings
White/gray rings
Gray/white rings
TSX DM 57 40E 09.2000
163
PCMCIA installation
7.5
Connection of the TSX SCP 112 card
At a Glance
Aim of this
Section
This Section deals with the hardware installation for TSX SCP 112 PCMCIA cards.
What’s in this
Section?
This Section contains the following Maps:
164
Topic
Page
Connection of the TSX SCP 112 card
165
Connecting in point to point mode
166
Multidrop connection
167
Dynamic performance
168
TSX SCP 112 connection with April 5000/7000 PLCs
171
TSX DM 57 40E 09.2000
PCMCIA installation
Connection of the TSX SCP 112 card
General
The PCMCIA TSX SCP 112 card is used to connect a Premium/Atrium PLC station
to a loop link with a current of 20 mA in point to point or multidrop.
Note: In all cases the power supply is: 24 V ± 20%, external to the TSX SCP
112 card, and must provide the current required for the current loop supply .
The TSX SCP CX 2030 cable is used for this type of connection (length 3 m).
Description of the TSX SCP CX 2030 cable:
The PCMCIA 20-pin mini-connector
supports the signals:
White/Blue
Orange/White
White/Green
Green/White
White/Orange
Blue/White
Note: A screw terminal block needs to be installed to connect the TSX SCP 112
card.
TSX DM 57 40E 09.2000
165
PCMCIA installation
Connecting in point to point mode
The diagram below describes the wiring principles for TSX SCP 112 loop current
PCMCIA cards in point to point. Point to point is only carried out according to 20 mA
mode when idle.
Illustration:
Station 1
SCP 112
Junction block 1
Blue/White
Blue/White
White/Orange
Green/White
White/Green
White/Blue
Green/White
White/Green
White/Blue
Station 2
SCP 112
White/Orange
General
Junction block 2
Note: Important: the cable shielding must be connected at the shortest point in the
junction blocks.
166
TSX DM 57 40E 09.2000
PCMCIA installation
Multidrop connection
General
Multidrop is only carried out in 0 mA idle mode. The send cable and receive cable
are set in parallel. The master is set by the software.
Example of connection of n TSX SCP 112 cards:
Station 3
TSX SCP 112
Green/White
White/Blue
White/Green
Orange/White
Green/White
White/Blue
White/Green
Orange/White
Station 2
TSX SCP 112
Green/White
White/Blue
White/Green
Orange/White
Station 1
TSX SCP 112
Rc
Junction block 1
Junction block 2
Rc = resistance of optional load
Junction block n
Note: Important: the cable shielding must be connected at the shortest point in the
junction blocks.
TSX DM 57 40E 09.2000
167
PCMCIA installation
Dynamic performance
General
The flow of a current loop link is limited by the cross-section and the length or the
cable used.
The user should refer to the two charts below to evaluate the performance which can
be obtained using this application.
Point to point
These curves are given for a shielded two pair cable (send through one pair, reception through the other) while observing all the precautions of use.
speed in Kbps
cable 1 mm2 4500 m max.
cable 0.64 mm2 2500 m max.
cable 0.34 mm2 1300 m max.
168
TSX DM 57 40E 09.2000
PCMCIA installation
Multidrop
The chart below is given for a shielded cable with a conductor cross-section of 0.34
mm2. The connection is made according to the parallel multidrop diagram below.
Using conductors with a larger cross-section improves the quality of the signals
transmitted:
Number of connected stations
Multidrop link performance is optimized when there are more connected stations.
The line is busier, which improves the quality of the transmitted signal.
When the connection is made according to the diagram above (See General, p.
167), the number of stations can be increased artificially (to a maximum of 16 stations) by loading the line at one of its ends.
This can be carried out by incorporating a load resistance.
This load resistance can be connected to any junction block providing it is between
pins 17 and 19 of cards TSX SCP 112.
The value of Lr resistance simulating the load of "N" stations is determined by the
formula:
U
Rc = ---------------N × 20
TSX DM 57 40E 09.2000
R in KΩ
U = external supply voltage
N = station number to be simulated
169
PCMCIA installation
Example:
An installation is physically made up of 6 stations connected in multidrop with an external 24 V supply.
The performance of the line is that of 10 stations, simulating the load of 4 additional
stations by a resistance:
24
Rc = --------------- = 0, 3KΩ
4 × 20
Note: The load resistance must not have an inductive effect or there is a risk that
it will not operate.
Use a thick layer of resistance.
170
TSX DM 57 40E 09.2000
PCMCIA installation
TSX SCP 112 connection with April 5000/7000 PLCs
General
PCMCIA card TSX SCP 112 20 mA current loop is used to connect April communication modules JBU0220 and JBU0250. The multidrop connection of PCMCIA
card TSX SCP 112 to modules JBU0220 and JBU0250 is carried out in series
mode. To connect April modules refer to reference manual TEM60000F.
Note: Important: You must configure card TSX SCP 112 in point to point mode
in the PL7 configuration screen, for both the point to point or the multidrop series.
Note: The current loop authorizes a current of 20 mA when idle, in point to point as
well as in multidrop mode.
If a slave is switched off the sender of this slave become active and the line is available.
If the loop supply is offset on one of the slaves, switching this slave off will cause
communication to be interrupted.
Point to point
link: Module
JBU0220 or
active JBU0250
Illustration
White/Blue
White/Green
Green/White
White/Orange
Blue/White
Passive master or slave:
TSX DM 57 40E 09.2000
Master or slave active
171
PCMCIA installation
Point to point
link: active
TSX SCP 112
card
Illustration:
White/Blue
White/Green
Green/White
White/Orange
Blue/White
Master or slave active
172
Master or slave passive
TSX DM 57 40E 09.2000
PCMCIA installation
Mixed terminal
links
Illustration:
White/Blue
White/Green
Green/White
White/Orange
Blue/White
Master or slave:
passive receiving
active sending
Multidrop type
link
Master or slave:
passive receiving
active sending
The following examples describe the different wiring possibilities for card TSX SCP
112 with modules JBU0220/0250.
Note: Important: The 24 V supply of each TSX SCP 112 present on the loop must
be connected, whether passively or actively, otherwise the link will not function.
These supplies must not have any shared (potential) point between them. Do
not connect the -24 V supply to the earth.
TSX DM 57 40E 09.2000
173
PCMCIA installation
Example 1: Active master TSX SCP 112 multidrop
White/Blue
White/Green
Green/White
White/Orange
Blue/White
Slave 1 passive
Master active
Slave 2 passive
174
TSX DM 57 40E 09.2000
PCMCIA installation
Example 2: active send/receive JBU0220/0250 multidrop
Master active
sending/receiving
Slave 1 passive
White/Blue
White/Green
Green/White
White/Orange
Blue/White
Slave 2 passive
TSX DM 57 40E 09.2000
175
PCMCIA installation
Example 3: Multidrop master JBU0220/0250 active send/receive - slaves
TSX SCP 112
White/Blue
White/Green
Green/White
White/Orange
Blue/White
Master active
sending/receiving
Slave 1 passive
White/Blue
White/Green
Green/White
White/Orange
Blue/White
Slave 2 passive
176
TSX DM 57 40E 09.2000
PCMCIA installation
Example 4: Multidrop active master TSX SCP 112
White/Blue
White/Blue
White/Green
White/Green
Green/White
Green/White
White/Orange
Blue/White
Master active
sending/receiving
White/Orange
Blue/White
Slave 1 passive
Slave 2 passive
TSX DM 57 40E 09.2000
177
PCMCIA installation
7.6
Connection of the TSX SCP 114 card
At a Glance
Aim of this
Section
This Section deals with the hardware installation of TSX SCP 114 PCMCIA cards.
What’s in this
Section?
This Section contains the following Maps:
178
Topic
Page
Connection to the UNI-TELWAY network
179
Connecting to the Modbus/Jbus bus
182
Multi-protocol asynchronous link connection RS 422
185
TSX DM 57 40E 09.2000
PCMCIA installation
Connection to the UNI-TELWAY network
General
Card TSX SCP 114, physical support RS 485, connects to the UNI-TELWAY network using cable TSX SCP CU 4030 via the connection device TSX SCA 50, or by
cable TSX SCP CU 4530 (provided with SUB-D 15 pin connector) via device TSX
SCA 62. The card is inserted in the processor or in module TSX SCY 21601.
The TSX SCA 50 is passive and made up of a printed circuit board fitted with 3 sets
of screw terminal blocks. It is used to connect a station by branching on the main
section of a UNI-TELWAY bus.
It ensures continuing operation of electrical signals, shielding and end of line adaptation function.
Type of
connection
The cable of the PCMCIA card has bare wires at its ends which the user must connect to the terminal located inside the device.
Illustration:
TSX SCP 114
TSX SCP CU 4030
Note: The branching device configures the wiring system of the card and a branching type of connection system.
TSX DM 57 40E 09.2000
179
PCMCIA installation
Description of
the TSX SCP CU
4030 cable
Illustration:
The PCMCIA 20-pin mini-connector
supports the signals:
TSX SCA 50 device
Red
White
White
Blue
Connection via a
TSX SCA 62
device
Illustration:
TSX SCP 114
TSX SCP CU 4530
180
TSX DM 57 40E 09.2000
PCMCIA installation
Description of
the TSX SCP CU
4530 cable
Illustration:
The PCMCIA 20-pin mini-connector
supports the signals:
TSX SCA 62 device
Red
White
White
Blue
15-pin SUB-D
TSX DM 57 40E 09.2000
181
PCMCIA installation
Connecting to the Modbus/Jbus bus
General
The TSX SCP 114 PCMCIA card is connected to the Modbus bus using the linking
cable TSX SCP CM 4030. This cable is connected to the branching device TSX SCA
50.
Type of
connection
The cable of the PCMCIA card has bare wires at its ends which the user must connect to the terminal located inside the device.
Illustration:
TSX SCP 114
TSX SCP CM 4030
Note: The length of the cable used (3 m), makes it possible to link a device to a
TSX SCA 50 connection device located within a 3 meter radius of the card. This
length ensures connection inside a standard cabinet
182
TSX DM 57 40E 09.2000
PCMCIA installation
Description of
the TSX SCP CM
4030 cable
Illustration:
The PCMCIA 20-pin mini-connector
supports the signals:
Green/White
White/Green
Orange/White
White/Orange
Brown/White
Note: Important: on a Modbus/Jbus bus you must:
l Polarize the line, in general in only one spot (usually on the master device) with
470 Ω resistance. Connect Rpull-down to EMI- (D(A)) and Rpull-up to EMI+ (D(B)).
l Adapt the line on the two end devices with a resistance of 150 Ω between EMI+
and EMI- (EMI+ is already connected internally by the card).
Important: to connect TSX SCP 114 card to a PLC Series 1000 (S1000), EMI+
must be connected to L-.
TSX DM 57 40E 09.2000
183
PCMCIA installation
Connecting
Modbus to
TSX SCA 50
device
Connection with no line terminator:
TSX SCA 50
Green/White
White/Green
Connection of a SCA 50 with line terminator:
TSX SCA 50
Green/White
White/Green
Orange/White
White/Orange
Brown/White
184
TSX DM 57 40E 09.2000
PCMCIA installation
Multi-protocol asynchronous link connection RS 422
General
Connecting the TSX SCP 114 card in Character Mode does not require any specific
accessories.
The product reference for the RS 485/RS 422 PCMCIA card linking cable is TSX
SCP CX 4030. It is 3 meters in length.
Type of
connection
The TSX SCP 114 PCMCIA card is connected in point to point to an RS 422A standard device VAX station type.
Illustration:
TSX SCP 114
Industrial computer
TSX SCP CX 4030
TSX DM 57 40E 09.2000
185
PCMCIA installation
Description of
the TSX SCP CX
4030 cable
Illustration:
The PCMCIA 20-pin mini-connector
supports the signals:
Green/White
White/Green
White/Orange
Orange/White
Brown/White
See also Connection in Character Mode, p. 142 (TSX SCY 21601 module integrated
link)
186
TSX DM 57 40E 09.2000
PCMCIA installation
7.7
Connection of the TSX FPP 20 card
Connecting the TSX FPP 20 card
General
The TSX FPP 20 PCMCIA card is connected to the FIPWAY network using a connector such as TSX FP ACC4 or TSX FP ACC 12.
To connect the PCMCIA card to the ACC4/ACC12 connector the user has the
choice of:
l Either a 1 m cable, product reference TSX FP CG 010.
l Or a 3 m cable, product reference TSX FP CG 030.
The elements required for connecting a Premium/Atrium PLC to the FIPWAY network are:
TSX FP ACC 4
TSX FPP 20
Receptor
Processor
or
TSX SCY 21601
Note: Important: TSX FP CG 010/030 cables connect and disconnect from the
PCMCIA card only when power is switched off.
TSX DM 57 40E 09.2000
187
PCMCIA installation
7.8
Connection of the TSX FPP 10 card
Connecting the TSX FPP 10 card
General
The TSX FPP 10 PCMCIA card is connected to the FIPWAY bus using a connector
such as TSX FP ACC 4 or TSX FP ACC 12.
To connect the PCMCIA card to the ACC4/ACC12 connector the user has the
choice of:
l Either a 1 m cable, product reference TSX FP CG 010.
l Or a 3 m cable, product reference TSX FP CG 030.
Elements required for connecting a Premium/Atrium PLC to the remote inputs/outputs FIPIO bus:
Receptor
Processor
TSX FPP 10
Note: Important: cables (TSX FP CG 010/030) are connected and disconnected
from the PCMCIA card only when power is switched off.
188
TSX DM 57 40E 09.2000
PCMCIA installation
7.9
Connection of the TSX MBP 100 card
At a Glance
Aim of this
Section
This Section deals with the hardware installation of TSX MPB 100 PCMCIA Modbus
+ cards.
What’s in this
Section?
This Section contains the following Maps:
TSX DM 57 40E 09.2000
Topic
Page
Connecting the TSX MBP100 card
190
General principle for connecting the PCMCIA card
191
Grounding the TSX MBP CE 030/060 cable
192
Connecting the TSX MBP CE 030/060 cable to Modicon connection device
990 NAD 230 00
193
189
PCMCIA installation
Connecting the TSX MBP100 card
General
190
The TSX MBP 100 PCMCIA card is connected to the Modbus+ network using the
TSX MBP CE 030 branch cable, 3 m long, or the TSX MBP CE 060, 3 m long. This
cable is connected to Modicon branch device (local site tap) 990NA23000.
For information on how to install a Modbus Plus network, see the Modicon Manual
" Modbus Plus Network-Installation and Planning Manual" Product Reference 890
USE 100 01".
TSX DM 57 40E 09.2000
PCMCIA installation
General principle for connecting the PCMCIA card
Principle
Illustration:
Branching device
Modicon 990 NAD 230 00
(Local Site Tap)
PCMCIA card
TSX MBP 100
TSX MPB CE 030/060 cable
Description of the TSX MBP CE 030/060 cable:
White
Blue
GND
GND
GND
White
Orange
Screening
braid
External
shielding
Loop
clamp
Note: Important: The cable’s main shielding is grounded using a metal clamp in
contact with the screening braid, which itself is fixed to the frame supporting the
rack.
This cable must be grounded, even if there is no PCMCIA card present.
TSX DM 57 40E 09.2000
191
PCMCIA installation
Grounding the TSX MBP CE 030/060 cable
Procedure
The cable connecting the PCMCIA card to the Modicon branching device must be
grounded as shown below:
1
Clip the loop clamp onto
the cable.
This loop clamp is delivered with the Modicon
branching device (Local
Site Tap), product reference 990 NAD 230 00.
TSX
MBP
Cable
TSX MPB CE
030
Loop
2
192
Fix the clamp + cable unit
to the frame. The frame itself is connected to the
ground.
TSX DM 57 40E 09.2000
PCMCIA installation
Connecting the TSX MBP CE 030/060 cable to Modicon connection
device 990 NAD 230 00
General
TSX MBP CE 030/060 cables are made up of two distinct sets of shielded twisted
pair wires and one external shielded ground wire, which makes a total of seven
wires.
Connection
procedure
To connect the cable to the Modicon device follow the procedure below:
Step
Action
1
Identify the wires:
l A first set of wires marked with the colors White and Orange, with one
stripped shielded wire.
l A second set of wires marked with the colors White and Blue, with one
stripped shielded wire.
l The external shielded wire
Note: It is important to correctly identify the two sets of twisted pairs since the
two white wires are not interchangeable
2
Set up the cable according to the dimensions given in the following illustration.
Illustration:
Blue/White
White/Orange
3
TSX DM 57 40E 09.2000
Insert the cable in the Modicon device and keep it in place using a clip.
193
PCMCIA installation
Step
4
Action
Connect the wires to the device, following the diagram below.
Diagram:
Branching device Modicon 990 NAD 230 00
Terminal
Wire color
O
Orange
W
White
GND
2 set shielding
W
White
BLU
Blue
Ground wire,
external
shielding
Cable clip
TSX MBP CE 030/060 cable
5
194
Remove the plastic hood from the terminal to connect each wire:
TSX DM 57 40E 09.2000
PCMCIA installation
Step
TSX DM 57 40E 09.2000
Action
6
Place each wire in the corresponding terminal slot:
7
Replace the hoods, and using a screwdriver press them to engage the wires in
their slots:
8
Finally, fix an open terminal to the external shielding wire either by soldering or
crimping, and connect it to the ground screw of the device as shown in stage 4
of the drawing.
195
PCMCIA installation
7.10
Summary of connection devices
Summary of connection devices
TSX SCP 111
card
TSX SCP 112
card
TSX SCP 114
card
196
Type of cable
Product reference
Designation
Modem cable
TSX SCP CC 1030
Connection cable via Modem DTE/
DCE 9 signals RS 232D, L=3 m.
Standard cable
TSX SCP CD 1030
TSX SCP CD 1100
Connection cable DTE/DTE RS 232D,
L=3 m or 10 m.
Type of cable
Product reference
Designation
Current loop cable
TSX SCP CX 2030
Current loop cable 20 mA, L=3 m.
Type of cable
Product reference
Designation
Universal cable
TSX SCP CX 4030
Universal cable type RS 485 and RS
422A, L=3 m.
UNI-TELWAY cable
TSX SCP CU 4030
Cable type RS 485, L=3 m.
Modbus cable
TSX SCP CM 4030
Cable type RS 485, L=3 m.
Connection device
TSX SCA 50
Connection device screwed to bus for RS
485 series link.
Connection device
TSX SCA 62
Connection device via connector to bus
for RS 485 series link.
Converter device
TSX SCA 72
RS 232D/RS 485 converter device.
TSX DM 57 40E 09.2000
PCMCIA installation
TSX FPP 10 and
TSX FPP 20
cards
TSX MPB 100
card
TSX DM 57 40E 09.2000
Type of cable
Product reference Designation
FIPWAY/FIPIO cable
TSX FP CG 010
Connection cable, L=1 m.
FIPWAY/FIPIO cable
TSX FP CG 030
Connection cable, L=3 m.
Connection device
TSX FP ACC4
FIPWAY/FIPIO connection device.
Connection device
TSX FP ACC12
FIPWAY/FIPIO connection device.
Type of cable
Product reference
Designation
Modbus+ cable
TSX MBP CE 030
Connection cable, L=3 m.
Modbus+ cable
TSX MBP CE 060
Connection cable, L=6 m.
197
PCMCIA installation
7.11
Precautions when connecting PCMCIA cards
Precautions for connecting PCMCIA cards
Important
Cards must be connected or disconnected in the host device (processor or TSX
SCY 21601) when the device is switched off.
The ferule, placed in direct contact with the PCMCIA card device, is used to handle
electrical interference carried by the link cable braids.
198
TSX DM 57 40E 09.2000
PCMCIA installation
7.12
Consumption of PCMCIA cards
Consumption of PCMCIA cards
TSX SCP 111
TSC SCP 112
TSC SCP 114
TSC FPP 10 and
TSX FPP 20
TSC MBP 100
TSX DM 57 40E 09.2000
Table of consumption:
Voltage
Typical current
Maximum current
Dissipated power
5 volts
140 mA
300 mA
1.5 W max.
Table of consumption:
Voltage
Typical current
Maximum current
Dissipated power
5 volts
120 mA
300 mA
1.5 W max.
Table of consumption:
Voltage
Typical current
Maximum current
Dissipated power
5 volts
150 mA
300 mA
1.5 W max.
Table of consumption:
Voltage
Typical current
Maximum current
Dissipated power
5 volts
280 mA
330 mA
1.65 W max.
Table of consumption:
Voltage
Typical current
Maximum current
Dissipated power
5 volts
220 mA
310 mA
1.55 W max.
199
PCMCIA installation
200
TSX DM 57 40E 09.2000
Communication: modules
TSX ETY 110/410/510
V
At a Glance
Aim of this Part
This part deals with installing ETHERNET network TSX ETY 110 and
TSX ETY 410/510 module hardware into a Premium/Atrium PLC.
What’s in this
part?
This Part contains the following Chapters:
TSX DM 57 40E 09.2000
Chapter
Chaptername
Page
8
Communication: TSX ETY 110 module
203
9
Communication: modules TSX ETY 410/510
219
201
TSX ETY 110/410/510
202
TSX DM 57 40E 09.2000
Communication: TSX ETY 110
module
8
At a Glance
Aim of this
Chapter
This Chapter deals with installing the ETHERNET network module TSX ETY 110, in
a Premium/Atrium PLC.
What’s in this
Chapter?
This Chapter contains the following Sections:
TSX DM 57 40E 09.2000
Section
Topic
Page
8.1
At a Glance
204
8.2
Description
205
8.3
Characteristics of the Ethernet channel
206
8.4
Installing the TSX ETY 110 module
207
8.5
Connection via the AUI interface
212
8.6
10baseT Interface
215
8.7
Display panel, diagnostics
217
8.8
Electrical features
218
203
TSX ETY 110
8.1
At a Glance
At a Glance
General
Communication module TSX ETY 110 is used to communicate in an Ethernet architecture. It is made up of a communication channel which offers two types of connections:
l Connection to an ETHWAY network supporting common words and X-WAY UNITE message-handling services on an ETHWAY profile.
l Connection to a TCP-IP network supporting the X-WAY UNI-TE message-handling service.
This module also ensures transparent routing of X-WAY UNI-TE messages from a
TCP-IP network to an X-WAY network, and vice versa.
Please refer to the Ethernet reference manual for wiring an ETHWAY architecture.
204
TSX DM 57 40E 09.2000
TSX ETY 110
8.2
Description
Description
General
Module TSX ETY 110 is a single (half size) module which is inserted in a rack slot
of a Premium PLC station.
Description:
1. Display panel indicating state of
module.
2. Standard connector for 10baseT
(RJ45) interface.
3. Standard connector for 10base5
(AUI) interface.
4. Thumbwheel to define station number and network number.
Illustration:
1
2
3
4
TSX DM 57 40E 09.2000
205
TSX ETY 110
8.3
Characteristics of the Ethernet channel
Characteristics of Ethernet channel
General
The module is made up of two standard interfaces for connecting to a network:
l One 10baseT interface on front panel of the module, comprising an RJ45 connector, which is used for a point to point link via a linking cable made up of two twisted
pairs of impedance 100 Ω ± 15 Ω.
l A 10base5 or AUI interface on front panel of module comprising a SUB-D 15-pin
connector, used to link to network by branching. This interface is also used to
supply active connection devices (Taps). It complies with the IEC 802 3 standard
and is used to connect any device which complies with this standard.
The type of connection is recognized automatically as soon as connection is made
to the network.
Services and operations supported by the module:
TCP-IP
services
UNI-TE
Ethway
services
UNI-TE
Common words
Application to application
Common
services
l
l
l
l
l
l
l
l
l
l
l
Client/server mode.
Synchronous requests of 256 bytes.
Asynchronous requests of 1 Kbyte.
Client/server mode.
Synchronous requests of 256 bytes.
Asynchronous requests of 1 Kbyte.
Shared database of 256 words
Message exchange in point to point 256 bytes
max.
X-WAY inter-network routing
X-WAY/UNI-TE routing
Module diagnostics
Note: The Ethernet driver supports the Ethernet II and (LCC+SNAP) 802.3 formats
on TCP-IP and LCC 802.3 on Ethway.
206
TSX DM 57 40E 09.2000
TSX ETY 110
8.4
Installing the TSX ETY 110 module
At a Glance
Aim of this
Section
This Section deals with installing module TSX ETY 110 in a PLC.
What’s in this
Section?
This Section contains the following Maps:
TSX DM 57 40E 09.2000
Topic
Page
At a Glance
208
Selecting the type of processor
209
Wiring/Unwiring with power switched on
210
Station address coding
211
207
TSX ETY 110
At a Glance
General
208
The communication module TSX ETY 110 is mounted in the rack slot of a Premium/
Atrium PLC station. It can be installed in any available slot (except in the offset X
Bus racks), on condition that the supply constraints of the rack are observed (see
Electrical characteristics, p. 218).
TSX DM 57 40E 09.2000
TSX ETY 110
Selecting the type of processor
Selection guide
Selecting the processor to control the PLC station will depend on the number of network connections required.
Processors
Number of network connections
Number of ETY 110 modules per station (*)
TSX 57 P 1../2..
PCX 57 253
1
1
TSX P 57 3..
PCX 57 353
3
3
TSX P 57 45.
4
4
(*) on condition of a consumption report on the 5V, compatible with the supply selected.
TSX DM 57 40E 09.2000
209
TSX ETY 110
Wiring/Unwiring with power switched on
The module
Module TSX ETY 110 can be wired or unwired with power switched on without disrupting the operation of the station.
The module does not have a RAM internal backup memory function: this will be
erased when power is switched off.
The module initializes itself when power is switched on. A communication break can
be expected during this intervention.
The link
The SUB-D 15-pin connectors of the AUI interface and the RJ45 connector of the
10baseT interface can be connected or disconnected when power is on. A communication break can therefore be expected in the application in progress.
210
TSX DM 57 40E 09.2000
TSX ETY 110
Station address coding
General
Four thumbwheels, which can be accessed from the front panel, are used to encode
the network number and the station number.
Illustration:
MSB
Number of network
LSB
MSB
Number of station
LSB
LSB = least significant bit
MSB = most significant bit
Values of coding possible in hexadecimal:
Network number
Station number
0 to 7F
0 to 3F
Example of coding:
Network 3: 16#03
Station 27: 16#1B
The thumbwheels are to be adjusted as follows:
0
PF
3
Pf
1
PF
B
Pf
Note: Caution: in an Ethernet network, there must only be one MAC address
for each station. Before modifying these addresses you must check that they
comply with the addressing plan of the carrier.
TSX DM 57 40E 09.2000
211
TSX ETY 110
8.5
Connection via the AUI interface
Connection by AUI interface
General
This interface is used to connect all types of devices which comply with the physical
layer defined in the OSI 802.3 standard (10base5, 10base2, FOIRL, etc.) through a
transceiver.
Module TSX ETY 110 can provide a remote power supply for the transceiver through
the Sub-D connector with the following characteristics:
l Imax = 0.5 mA
l 12 V-6%<Usupply<15 V+15%
The module is connected to the main cable via a transceiver and by the following
branch cables:
l TSX ETY CB 005 - Length 5 m
l TSX ETY CB 010 - Length 10 m
l TSX ETY CB 020 - Length 20 m
The maximum length of a branch may be 50 m. This length can be achieved by connecting several branch cables end to end.
Note: It is essential to use transceivers (TSX ETH ACC2) to connect two modules in point to point.
212
TSX DM 57 40E 09.2000
TSX ETY 110
Connector
pinouts
Topology
Sub-D 15 pins according to the OSI 802.3 standard:
Pin number
Designation according to
ISO 802.3
Use
1
CI-S (Control In Shield)
GND
2
CI-A (Control In A)
COLL+
3
DO-A (Data Out A)
TD+
4
DI-S (Data In Shield)
GND
5
DI-A (Data in A)
RD+
6
VC (Voltage Common)
GND
7
not used
8
not used
9
CI-B (Control In B)
COLL-
10
DO-B (Data Out B)
TD-
11
DO-S (Data Out Shield)
GND
12
DI-B (Date In B)
RD-
13
VP (Voltage Plus)
12 V
14
VS (Voltage Shield)
GND
15
not used
Sub-D connector body
PG (Protective Ground)
Protective ground
Illustration:
Sender/Receiver
TSX ACC2
TSX ETY CBXXX
Station i
TSX DM 57 40E 09.2000
Station j
213
TSX ETY 110
Locking
The Sub-D connector is equipped with a sliding lock system The connector is locked
by sliding the tab to the bottom. To ensure the module works properly in a disturbed
environment it is essential to carry out the locking procedure.
Illustration:
Locking tab
214
TSX DM 57 40E 09.2000
TSX ETY 110
8.6
10baseT Interface
10baseT interface
General
This interface has a standard type RJ45 connector. These connection cables are
widely used in business.
In an industrial environment, you must use a cable with the following characteristics:
l Shielded twisted double pair
l Impedance 100 Ω±15 Ω (from 1 to 16 MHz)
l Maximum attenuation 11.5 dB/100 meters
l Maximum length 100 meters
The 10baseT connection is a point to point connection to form a star-shaped network. The stations are connected to concentrators or switches.
Pinouts
Illustration:
Reminder of pinouts:
TSX DM 57 40E 09.2000
Pin
Signal
1
TD+
2
TD-
3
RD+
4
not connected
5
not connected
6
RD-
7
not connected
8
not connected
215
TSX ETY 110
Topology
This link is used to create a star-shaped network with connections in point to point.
The stations are connected to a concentrator (Hub). The concentrators can also be
connected in cascade to increase network size.
Illustration:
Concentrator 1
Stations
Station 1
Concentrator 2
Station 2
Stations
216
TSX DM 57 40E 09.2000
TSX ETY 110
8.7
Display panel, diagnostics
Display panel, diagnostics
General
The display panel complies with the Premium standard
Diagnostics
RUN
ERR
RUN
ERR
COL
ADR
RX
TX
Meaning of the diagnostics LEDs:
COL
ADR
TX
RX
Meaning
O
P
ns
ns
ns
ns
Module not operational.
O
F
O
O
O
O
Module not configured or configuration error.
F
F
O
O
O
O
Module running self-test.
P
O
O
O
F
O
Ethernet communication sending.
P
O
O
O
O
F
Ethernet communication receiving.
P
O
O
O
F
F
Ethernet communication in sending/receiving.
P
O
F
O
F
O
Module has detected collision.
P
O
O
P
O
O
Duplicate MAC address.
O
O
O
P
O
O
Network address beyond limits.
P = Permanently on, F = flashing, O = Off, ns = not significant
TSX DM 57 40E 09.2000
217
TSX ETY 110
8.8
Electrical features
Electrical characteristics
General
Module TSX ETY 110 can be inserted in any rack slot of a Premium/Atrium station
(except in an X Bus offset rack). The module consumption from the supply depends
on the selection made from the transceiver remote power supply option.
Table of consumption:
Voltage
Current consumed
Dissipated power
5 volts
Typical
Maximum
Typical
Maximum
with remote power supply
(RJ45)
0.8 A
1.2 A
4W
6W
with remote power supply
(AUI)
1.2 A
2.5 A
6W
12.5 W
Note: Caution: Modules TSX ETY 110 on 5 volts have high consumption when the
AUI connection is used. Special attention should therefore be given what sort of devices are in the rack before deciding which kind of supply to choose.
Number of TSX ETY 110 modules which can be connected to a rack:
l 2 modules with AUI connection.
l 4 modules with RJ45 connection.
218
TSX DM 57 40E 09.2000
Communication: modules
TSX ETY 410/510
9
At a Glance
Aim of this
Chapter
This Chapter deals with installing ETHERNET network modules TSX ETY 410 and
TSX ETY 510, in a Premium/Atrium PLC.
What’s in this
Chapter?
This Chapter contains the following Sections:
TSX DM 57 40E 09.2000
Section
Topic
Page
9.1
At a Glance
220
9.2
Description
221
9.3
Characteristics of the Ethernet channel
222
9.4
Installation of modules TSX ETY 410/510
223
9.5
10/100baseT interface
227
9.6
Display, diagnostics
228
9.7
Electrical characteristics
230
9.8
Standards
231
9.9
Operating conditions
232
219
TSX ETY 410 TSX ETY 510
9.1
At a Glance
At a Glance
General
Communication modules TSX ETY 410/510 are used to communicate in an Ethernet
architecture. They are made up of a communication channel whose main characteristics are as follows:
l Connection to a TCP/IP network.
l Communication in Half and Full Duplex mode by automatic recognition.
l Transmission speed from 10 or 100 Mbits/s by automatic recognition.
l Connection to network by copper cable via an RJ45 connector.
These modules are used to carry out the following functions:
X-WAY UNI-TE messaging service and Modbus on TCP/IP.
I/O scanner service.
SNMP service.
Web server.
l
l
l
l
220
TSX DM 57 40E 09.2000
TSX ETY 410 TSX ETY 510
9.2
Description
Description
General
Modules TSX ETY 410 are single format modules which are inserted in a slot on the
main or extension rack of a Premium PLC station.
Description:
Illustration:
1. Display panel indicating module
state:
l One green RUN LED.
l Two red LEDs: ERR and COL.
l Three yellow LEDs: STS, TX and
RX.
2. Standard connector for 10baseT
(RJ45) interface.
1
2
TSX DM 57 40E 09.2000
221
TSX ETY 410 TSX ETY 510
9.3
Characteristics of the Ethernet channel
Characteristics of the Ethernet channel
General
The modules have a standard interface for connecting to a 10/100baseT network
and the front panel, a RJ45 connector for a pin-to-pin link via a link cable comprising
two independent twisted pairs.
Services and functions supported by the modules:
Support
Utility
Protocol
TCP-IP
services
Messaging
UNI-TE
Modbus
I/O scanner
Modbus
Network man- SNMP
agement
Web
HTTP
Functions
l
l
l
l
l
l
l
l
Management BOOTP
of IP addresses
222
l
Client/server mode.
Synchronous requests of 256 bytes.
Asynchronous requests of 1 Kbyte.
Data exchange.
Access to inputs/outputs
SNMP, MIB II agent.
Preset, non-modifiable website on TSX ETY
410.
Website which can be modified and extended
within the limit of 7.5Mb on TSX ETY 510
Client and address server
TSX DM 57 40E 09.2000
TSX ETY 410 TSX ETY 510
9.4
Installation of modules TSX ETY 410/510
At a Glance
Aim of this
Section
This Section deals with installing modules TSX ETY 410 and TSX ETY 510 in a PLC.
What’s in this
Section?
This Section contains the following Maps:
TSX DM 57 40E 09.2000
Topic
Page
At a Glance
224
Selecting the type of processor
225
Wiring/Unwiring with power switched on
226
223
TSX ETY 410 TSX ETY 510
At a Glance
General
224
Communication modules TSX ETY 410/510 are mounted in the rack slot of a Premium/Atrium PLC station. They can be installed in any available slot (except in an
offset X Bus rack), on condition that the supply constraints of the rack are observed
(see Electrical characteristics, p. 230).
TSX DM 57 40E 09.2000
TSX ETY 410 TSX ETY 510
Selecting the type of processor
Selection guide
Selecting the processor to control the PLC station will depend on the number of network connections required.
Processors
Number of network connections
Number of ETY 410/510 per station (*)
TSX 57 P 1../2..
PCX 57 253
1
1
TSX P 57 3..
PCX 57 353
3
3
TSX P 57 45.
4
4
(*) on condition of a consumption report on the 5V, compatible with the supply selected.
TSX DM 57 40E 09.2000
225
TSX ETY 410 TSX ETY 510
Wiring/Unwiring with power switched on
The module
Modules TSX ETY 410/510 can be wired or unwired when switched on without disrupting the operation of the station.
The modules do not have an internal RAM backup memory function: this will be
erased when power is switched off.
The modules reset when switched on. A communication break can be expected during these interventions.
The link
The 10/100baseT interface RJ45 connector can be connected or disconnected
when power is on. A communication break can therefore be expected in the application in progress.
226
TSX DM 57 40E 09.2000
TSX ETY 410 TSX ETY 510
9.5
10/100baseT interface
10/100base T interface
General
This interface has a standard type RJ45 connector.
Refer to the ETHERNET reference manual for the connection accessories which
comply with environmental circumstances the PLC requires in an industrial setting.
Pinouts
Illustration:
Reminder of pinouts:
Pin
Signal
1
TD+
2
TD-
3
RD+
4
not connected
5
not connected
6
RD-
7
not connected
8
not connected
Note: If there is a connection via a shielded cable, the connector casing on the
module is linked up to the ground connection.
TSX DM 57 40E 09.2000
227
TSX ETY 410 TSX ETY 510
9.6
Display, diagnostics
Display panel, diagnostics
General
The display panel conforms to the Premium standard
RUN
ERR
STS
ADR
RX
TX
The COL, RX and TX LEDs are managed by the line’s electronics; they indicate:
l COL: a collision.
l RX: a receive
l TX: a transmission.
Diagnostics
Meaning of the diagnostics LEDs:
RUN
ERR
STS
COL
TX
RX
Meaning
O
O
O
ns
ns
ns
No supply to module.
O
O
P
ns
ns
ns
Module running self-test.
P
O
O
ns
ns
ns
Module ready.
O
P
O
ns
ns
ns
Module not operational.
O
P
P
ns
ns
ns
Software operation error. Temporary state causing module reinitialization.
O
F
P, F
ns
ns
ns
Module not configured or configuration in progress.
P
O
P
ns
ns
ns
Module configured, operational.
P = Permanently on, F = flashing, O = Off, ns = not significant
228
TSX DM 57 40E 09.2000
TSX ETY 410 TSX ETY 510
RUN
ERR
STS
COL
TX
RX
Meaning
ns
ns
F
ns
ns
ns
Module configured. Diagnostics according to how the LEDs are flashing:
l 2 flashes: module has no MAC address.
l 3 flashes: ETHERNET cable not connected on the module or Hub
side
l 4 flashes: the module IP address is duplicated by another IP address on the network. Conflicting remote device flashing in the
same way.
l 5 flashes: module configured as a BOOTP client and is waiting for
a BOOTP server response.
P
O
P
O
F
O
ETHERNET communication sending.
P
O
P
O
O
F
ETHERNET communication receiving.
P
O
P
O
F
F
ETHERNET communication sending/receiving.
P
O
P
F
F
O
Module has detected collision.
P = Permanently on, F = flashing, O = Off, ns = not significant
TSX DM 57 40E 09.2000
229
TSX ETY 410 TSX ETY 510
9.7
Electrical characteristics
Electrical characteristics
General
Modules TSX ETY 410/510 can be inserted in any rack slot of a Premium/Atrium
station (except in the X Bus offset rack).
Table of consumption:
230
Voltage
Current consumed
Dissipated power
5 volts
Typical
Maximum
Typical
Maximum
TSX ETY 410/510
360 mA
400 mA
1.8 W
2.1 W
TSX DM 57 40E 09.2000
TSX ETY 410 TSX ETY 510
9.8
Standards
Norms and standards
Compliance with
standards
TSX DM 57 40E 09.2000
The TSX ETY 410 and TSX ETY 510 modules comply with the following standards:
l UL 508
l CSA
l IEC 1121-2
l Marine classification
231
TSX ETY 410 TSX ETY 510
9.9
Operating conditions
Operating conditions
Applicable
conditions
232
l Configuration software:
l TSX ETY 410: PL7 version V3.4C and TSX ETY 410 update
l TSX ETY 510: PL7 version V4.0
l Conditions of use:
l Temperature between 0 and +60° C
l Relative humidity between 10% and 95% (without condensation) at 60° C
l Altitude between 0 and 4500 meters
l Immunity to vibrations complies with the IEC 68-2-6 standard, Fc test
l Immunity to shocks complies with the IEC 68-2-27 standard, Ea test
l Immunity to free fall, hardware dealt with as per the IEC 68-2-32 standard,
method 1
l Protection index IP 20
l Storage conditions:
l Temperature between -40° C to +85° C
l Relative humidity between 0% and 95% (without condensation) at 60° C
TSX DM 57 40E 09.2000
Communication: PCMCIA Modem
card
VI
At a Glance
Aim of this Part
This part deals with the TSX MDM 10 PCMCIA modem card.
What’s in this
part?
This Part contains the following Chapters:
Chapter
10
TSX DM 57 40E 09.2000
Chaptername
Installing the TSX MDM 10 module
Page
235
233
PCMCIA Modem
234
TSX DM 57 40E 09.2000
Installing the TSX MDM 10 module
10
At a Glance
Aim of this
Chapter
This Chapter describes the hardware installation of the PCMCIA Modem card
TSX MDM 10.
What’s in this
Chapter?
This Chapter contains the following Sections:
TSX DM 57 40E 09.2000
Section
Topic
Page
10.1
At a Glance
236
10.2
Description
237
10.3
Installation
238
10.4
Connecting adapters
242
10.5
Electrical characteristics
243
10.6
Technical specifications
244
235
TSX MDM 10
10.1
At a Glance
At a Glance
General
The TSX MDM 10 card is used to connect to the switched telephone network (STN)
for accessing remote stations following UNI-TELWAY or character mode protocols.
This type of communication is available using the Modem PCMCIA card. It is installed only in the PCMCIA reception slot on a Premium processor version V≥3.3.
236
TSX DM 57 40E 09.2000
TSX MDM 10
10.2
Description
Description
General
The TSX MDM 10 is made up of the following elements:
1. A PCMCIA Modem card
2. A cable for connecting to the dialed-up telephone network
3. An RJ 11 port for connecting to a telephone adapter (4) or
directly to a telephone port.
4. A telephone adapter (in line with country of purchase) enabling a link to the telephone network.
TSX DM 57 40E 09.2000
237
TSX MDM 10
10.3
Installation
At a Glance
Aim of this
Section
This Section deals with installing a PCMCIA Modem card in a Premium PLCTSX
MDM 10.
What’s in this
Section?
This Section contains the following Maps:
238
Topic
Page
Selecting the type of processor and slot
239
Wiring/Unwiring with power switched on
240
Connecting to the telephone network
240
TSX DM 57 40E 09.2000
TSX MDM 10
Selecting the type of processor and slot
General
The TSX MDM 10 card is to be installed onlyin the PCMCIA reception slot of the
processor.
Illustration:
Reception slot
Premium processor
Reception slot
TSX SCY 2106
Reception slot
Atrium processor
Note: Reminder: the TSX MDM 10 card is compatible with all Premium processors
version V≥3.3.
Note: Reminder: Atrium processors and communication modules TSX SCY 21601
do not accept modem card TSX MDM 10
TSX DM 57 40E 09.2000
239
TSX MDM 10
Wiring/Unwiring with power switched on
Precautions
Inserting or removing the TSX MDM 10 communication card is forbidden when the
reception module (processor) is switched on.
Connecting to the telephone network
Procedure
To connect the modem to the telephone network proceed as follows:
Step
240
Action
1
Connect the RJ 11 port to the
telephone adapter if necessary
2
Plug in the RJ 11 port or adapter
of your telephone line.
If a device is already connected
to this port, unplug it then plug in
the telephone adapter instead.
Plug in the device to the port panel at the back of the adapter.
Illustration
TSX DM 57 40E 09.2000
TSX MDM 10
Step
TSX DM 57 40E 09.2000
Action
3
Insert the PCMCIA card in the
processor slot provided for this
purpose.
Caution: The processor must be
switched off while inserting or removing the PCMCIA card
4
Screw the card into the processor to stop it shifting when power
is on.
Illustration
241
TSX MDM 10
10.4
Connecting adapters
Different adapters
At a Glance
242
The telephone adapters, in line with the country of purchase, are used to ensure
connection between an RJ 11 port of PCMCIA card TSX MDM 10 and the wall socket of the telephone network.
To use the TSX MDM 10 card in a different country all you need to do is change the
telephone adapter.
List of adapter product references according to the country:
Country
Product reference
Germany
TSX MDM EDT G
Belgium
TSX MDM EDT B
Spain
TSX MDM EDT S
France
TSX MDM EDT F
Italy
TSX MDM EDT T
TSX DM 57 40E 09.2000
TSX MDM 10
10.5
Electrical characteristics
Electrical characteristics
Consumption
TSX DM 57 40E 09.2000
This table indicates the consumption of a PCMCIA modem card:
Voltage
Typical current
5 volts
195 mA
243
TSX MDM 10
10.6
Technical specifications
At a Glance
Aim of this
Section
This Section deals with the technical specifications for the PCMCIA Modem card
TSX MDM 10.
What’s in this
Section?
This Section contains the following Maps:
244
Topic
Page
Communication protocols
245
Operating characteristics
246
Maximum operating temperature
247
EC labeling
248
TSX DM 57 40E 09.2000
TSX MDM 10
Communication protocols
General
TSX DM 57 40E 09.2000
The TSX MDM 10 card supports the various ITU-T V.32 communication protocols.
245
TSX MDM 10
Operating characteristics
At a Glance
246
The TSX MDM 10 card has the following characteristics:
l Sends AT commands
l Half and Full Duplex communication
l Automatic calls and replies
l Calls by pulses or tones
TSX DM 57 40E 09.2000
TSX MDM 10
Maximum operating temperature
Values
TSX DM 57 40E 09.2000
l Without ventilation module TSX FAN... : 50° C max.
l With ventilation module TSX FAN... : 60° C max.
247
TSX MDM 10
EC labeling
General
Card TSX MDM 10 conforms to the European Telecommunications Directive
DTTC 98/13/EC.
Guaranteed level of immunity to electromagnetic fields: 3 V/m.
Communication faults may appear beyond this threshold (in compliance with Directive CEM 89/336/EEC, applicable in residential and business areas, and areas of
light industry.)
Card TSX MDM 10 also complies with the Low Voltage Directive 73/23 EEC, updated by 93/68/EEC.
248
TSX DM 57 40E 09.2000
B
AC
Index
A
AS-i Bus Diagnostics, 102
C
Characteristics
AS-i bus, 86
Terminal port, 46
TSX SAY 100, 98
Communication
Character string, 25
Man-machine interface console, 23
UNI-TELWAY master/slave, 24
With terminal, 21
Connection
Character Mode, 142
TSX FPP 10, 188
TSX FPP 20, 187
TSX MBP 100, 189
TSX SAY 100, 92
TSX SCA 50, 141
TSX SCP 111, 161
TSX SCP 112, 164
TSX SCP 114, 178
Consumption
TSX ETY 110, 218
TSX ETY 410/510, 230
TSX FPP 10/20, 199
TSX MBP 100, 199
TSX MDM 10, 243
TSX SCP 111, 199
TSX SCP 112, 199
TSX SCP 114, 199
TSX SCY 21601, 143
I
Integrated FIPIO link
Premium/Atrium processors, 72
M
Mounting
PCMCIA, 155
P
PCMCIA
Visual diagnostics, 158
T
Terminal port
Connector pin configuration, 48
on Premium and Atrium, 19
TSX DM 57 40E 09/2000
249
Index
Terminal Port Connections
Summary table, 43
Terminal port connections, 27
Character string, 40
Inter-device UNI-TELWAY, 38
Inter-PLC UNI-TELWAY, 36
Man-machine interface console, 30
Master UNI-TELWAY, 34
Model 40 PLCs, 39
Modem, 32
Programming terminal, 28
Slave UNI-TELWAY, 35
TSX ETY 110
10baseT interface, 215
Connection by AUI interface, 212
Diagnostics, 217
Ethernet channel characteristics, 206
Station address, 211
TSX ETY 410/510
10/100baseT interface, 227
Diagnostics, 228
Ethernet channel characteristics, 222
Operating conditions, 232
TSX MDM 10
Telephone network connection, 240
TSX P ACC 01
Connecting devices, 61
Connecting to Premium/Atrium PLCs, 57
Connection between 2 PLCs, 66
Connector pin configuration, 59
Dimensions, 54
External appearance, 52
Internal view, 55
Master UNI-TELWAY, 63
Slave UNI-TELWAY, 65
Standard functions, 51
Switches, 58
UNI-TELWAY Bus connection, 56
TSX SAY 100
Display, 95
I/O addressing, 100
Operating modes, 108
Physical presentation, 89
250
TSX SCY 21601
Description, 121
Installation, 125
Integrated channel characteristics, 123
Operation, 127
Reception channel compatibility, 124
UNI-TELWAY bus connection, 132
Visual diagnostics, 128
TSX DM 57 40E 09/2000
">