advertisement
USB2.0 to Ethernet adapter
Q u i i c k I I n s s t t a l l l l a t t i i o n G u i i d e
Version 1.0 July, 2006
M u l l t t i i L a n g u a g e s Q I I G i i n D r i i v e r C D
= = = = = = = = = = = = = = = = = = = = = = = = = = = = =
Č e s k ý Anglického průvodce rychlou instalací naleznete na přiloženém CD s ovladači
D e u t t s c h : : Finden Sie bitte das englische QIG beiliegend in der Treiber CD (German)
E s p a ñ o l l: Incluido en el CD el QIG en Ingles.
F r a n ç a i i s : le CD driver
: Veuillez trouver l’anglais QIG ci-joint dans
I I t t a l l i i a n o : : Incluso nel CD il QIG in Inglese.
M a g y a r r : : Az angol telepítési útmutató megtalálható a mellékelt CD-n
N e d e r r l l a n d s bijgesloten CD
De engelstalige QIG treft u aan op de
P o l l s k i i: Skrócona instrukcja instalacji w języku angielskim znajduje się na załączonej płycie CD
P o r t u g u ê s: Incluído no CD o QIG em inglês.
Р у с с к и й : : Найдите QIG на анлийском языке на приложеном CD
T ü r r k ç e : : Ürün ile beraber gelen CD içinde Türkçe Hızlı
Kurulum Kılavuzu'nu bulabilirsiniz
English
Introduction
Thank you for purchasing the USB2.0 10/100Mbps to Fast Ethernet
Adapter. This unique cable adapter allows you to connect your computer into Internet in the fast and easy way.
Specifications
Standards z z
IEEE 802.3 10Base-T and 802.3u 100Base-TX Compliant
USB specification 1.0 /1.1 and 2.0 compliant
Connection Mode z
Full or Half duplex for both 10Mbps and 100Mbps
Media Supported z
Category-3, 4, 5 for 10Base-T and Category 5 for 100Base-TX
LEDs z
Link/Active LED indicator
Feature z z z z z z
USB specification revision 1.0/1.1 and 2.0 full speed compliant
Complies with IEEE 802.3 10Based-T and 802.3u 100Base-TX
USB interface to desktop/notebook PC without power adapter
RJ-45 connector to 10Mbps or 100Mbps Ethernet networks
10/100Mbps Auto-Sense
Full/Half Duplex auto-negotiation for both 10Base-T and 100Base-TX
Compatible with Windows 98SE / ME / 2000 / XP
Device Installation Guide
Follow the steps below on installing the USB2.0 10/100 Fast Ethernet adapter cable:
Step1.
Please connect the male B-connector of 1.5M USB2.0 cable to the female
USB B-connector of USB2.0 Fast Ethernet Adapter and RJ-45 connector of networking cable to another end of USB2.0 Fast Ethernet Adapter.
Step2.
Connect the male A-connector of 1.5M USB2.0 cable to an available
USB2.0 port on the computer or an available USB2.0 port on the USB2.0
HUB plugged into the computer.
D r i i v e r i i n s t a l l l l a t i i o n f f o r W i i n d o w s 9 8 S E / / M e
Step1. Power on the computer. “New Hard Ware Found” window comes up to request you to insert the driver diskette, and click “OK”.
Step2. Select “Search the proper files of driver”, and click “Next”.
Step3. Insert the driver disc into the computer. Select “CD-ROM Devices” or “specify a Location” link D:\Driver\EU-4206, and click “Next”.
Step4. The driver will be found, and click “Next” to proceed.
Step5. The system will ask windows 98SE original disk.
Step6. Please insert the disk, and the system will install driver automatically.
Step7. Click “Finished” completing installation.
Step8. Windows 98SE / Me will find the driver and automatically configure the USB Fast Ethernet Adapter.
Step9. Reboot the computer and remove the driver disc. The driver will take effect.
Step10. Check if the device is complete install in your computer“ My
Computer → (right key on the mouse) content → Hardware →
Device Manager.
D r i i v e r i i n s t a l l l l a t i i o n f f o r W i i n d o w s 2 0 0 0
Step1. Power on the computer. When the “New Hardware Found Wizard” window comes up, click “Next” to install the driver.
Step2. Select “Search the proper files of driver”, and click “Next”.
Step3. Insert the driver disc into the computer. Select “CD-ROM Devices” or “specify a Location” link D:\Driver/EU-4206, and click “Next”.
Step4. The driver will be found, and click “Next” to proceed.
Step5. Click “Finished” to complete installation.
Step6. Windows 2000 will automatically configure the USB Fast Ethernet
Adapter.
Step7. Reboot the computer and remove the driver disc. The driver will take effect.
Step8. Check if the device is complete install in your computer “ My
Computer → (right key on the mouse) content → Hardware →
Device Manager.
D r i i v e r I I n s t a l l l l a t i i o n f f o r W i i n d o w s X P
Step1. Power on the computer. When the “New Hardware Found Wizard” windows comes up, select “install from a list or a specific location
(Advanced)”, and click “Next”.
Step2. Insert the driver disc into the computer. Select “CD-ROM Devices” or “specify a Location” link D:\Driver/EU-4206, and click “Next”.
Step3. Windows XP will find the driver and request to continue installing and copying needed files”.
Step4. Click “Finished” to complete the installation.
Step5. A dialogue box will appear above the taskbar showing “New network device installed”.
Step6. Reboot the computer and remove the driver disc. The driver will take effect.
Step7. Check if the device is complete install in your computer“ Star →
My Computer → (right key on the mouse) content → Hardware →
Device Manager
advertisement
Related manuals
advertisement