advertisement
TECSUN TECSUN
PL-680
PLL SYNTHESIZED RECEIVER
FM STEREO / MW / LW / SW-SSB / AIR BAND
OPERATION MANUAL
TECSUN ELECTRONIC IND. LTD.
Address: Rm 11, 13/F, Block A, Hoi Luen Ind. Ctr.,
55 Hoi Yuen Road, Kwun Tong, Kowloon, Hong Kong.
E-mail: [email protected]
Website: www.tecsun.com.cn
20150116
TECSUN ELECTRONIC IND. LTD.
FEATURES
FM-stereo/MW/LW/SW/SW SSB/AIR band with high sensitivity, selectivity and user-friendliness
FM band coverage: 76 – 108 MHz
Shortware Single Side Band (SSB) with upper sideband (USB) and lower sideband (LSB)
Equipped with Synchronous Detector and Dual Conversion technology for MW band; this greatly enhances the receiver’s sensitivity, selectivity, image rejection, and interference from adjacent stations
FM/SW external antenna jack sensitivity selector: DX/Normal/
Local antenna gain
Multiple tuning methods
Store up to 2000 stations (manually, semi-automatic and fully automatic)
Equipped with a high-sensitivity acoustic speaker with treble/bass tone control switch (FM-stereo via earphone)
Auto Alarm-Off Timer: when the alarm goes off, the preset radio station will play for 1-90 minutes
Sleep timer (1-120 minutes) to turn off the radio automatically
User-friendly interface
Built-in charging function
Powered by 4 x AA (R6) size batteries, DC 6V
Luxury carrying case
Dimensions: 188 x 116 x 31 mm
SPECIFICATIONS
8. Station Memory 2000M in total
800 memories for each band:
FM: 100M
MW: 100M
LW: 100M
SW: 200M
SSB: 200M
AIR: 100M
1200 memories for 12 memory pages (each page 100 memories)
9. Alarm Mode: alarm by radio only (2 presettings)
10. Quiescent Current
FM < 50mA
MW/LW < 70mA
SW < 70mA
SSB < 70mA
AIR < 70mA
Standby < 80uA
11. Speaker: Φ77 mm / 16 Ohm / 1W Cone speaker
12. Earphone Jack: Φ3.5mm, 32 Ohm, Stereo type
13. Power supply:
Battery: UM3 or AA X 4
External adaptor: DC 6V, ≥ 300mA
14. Unit Dimensions: approx. 188(W) X 116(H) X 31(D) mm
15. Weight: 475g (Batteries not included)
PL-680 25
TABLE OF CONTENTS
CONTROL LOCATIONS...................................................................................... 2
LCD DISPLAY .......................................................................................................
4
HOW TO TURN ON/OFF THE RADIO.................................................................5
TUNING INTO STATIONS....................................................................................6
Manual Station Tuning
Auto Browse Station
Direct Keypad Entry
WORKING WITH STATION MEMORIES.............................................................8
Storing Stations Manually
Semi-Automatic Station Storage
ATS (Auto Tuning Storage)
Memory Tuning Manually
Auto Browse Memory
Direct Key in Memory Address
Delete Single Memory Manually
Semi-Auto Delete Memory
Delete ALL Memories within a Page
LISTENING TO STORED STATIONS................................................................12
SLEEP FUNCTION............................................................................................13
TIME SETTING..................................................................................................13
ALARM SETTING..............................................................................................14
SETTING ALARM STATION
SETTING THE ALARM TIME
SNOOZE FUNCTION........................................................................................15
INTELLIGENT LIGHT FUNCTION.....................................................................15
TUNING STEP SETTINGS................................................................................16
FM ST. (FM STEREO).......................................................................................16
AM BW (BANDWIDTH) ......................................................................................17
ANT. GAIN..........................................................................................................17
TONE CONTROL...............................................................................................17
KEY-LOCK FUNCTION......................................................................................17
INTELLIGENT CHARGING FUNCTION ............................................................18
SINGLE SIDE BAND (SSB)...............................................................................18
SYNCHRONOUS DETECTOR ..........................................................................19
HOW TO IMPROVE FM / SW RECEPTION......................................................19
SYSTEM SETTINGS ......................................................................................... 20
RESET PROCEDURE........................................................................................21
IMPORTANT MATTERS FOR USING BATTERIES...........................................21
TROUBLE SHOOTING......................................................................................22
SPECIFICATIONS..............................................................................................23
PL-680 1
CONTROL LOCATIONS
2 PL-680
1
2
3
4
5
Power / Sleep button
Time set button
Timer A Alarm set button
Timer B Alarm set button
FM & SW Telescopic Antenna
6
7
8
Light / Snooze / Step button
VF / VM / SCAN
-/+ PAGE buttons
9
10
Air Band button
Single Side Band (SSB) button
11
12
Synchronous (SYNC) button
FM. ST & AM BW select button
13
14
FM / AM (MW, LW) / SW Band & ATS buttons
Delete / Enter button
15 Key lock button
16
17
Memory / Battery button
Hand Carry Strap
18 FM / SW Antenna Jack
19 ANT. Gain (DX / Normal / Local) switch
20 Treble / Bass Tone Control
21 Earphone Jack
22 DC 6V Jack
23
24
Metal Stand
Tuning Knob
25 SSB BFO knob
26 Volume knob
27 Reset button
Note: For the silk-printing in red or orange on radio with brackets,
it means that you can only operate it when radio is off.
PL-680 3
LCD DISPLAY
4
19
18
17
1 2 3 4 5 6 7
Ni-MH
Battery
0 1 2 3 4 5
SL EEP
Timer A
Timer B
Charge
AIR
FM MW LW Shortwave BW
PAGE
FAST
SLOW kHz
MHz
A
PRESET
SYNC
B mb
8
9
10
11
16 15 14 13 12
1
2
Battery Consumption indicator
“ ” : Full
“ ” : Empty
Signal Strength indicator
1 2 3 4 5
1 2 3 4 5
6
7
4
5
10
11
12
13
3
8
9
14
15
16
17
18
19
Digital Number Display:
With radio off: Time & System settings
With radio on: Frequency or Error display
Sleep timer indicator
Alarm Timer A or B – Timer indicator
Charging Indicator
Digital Number Display:
With radio off: preset alarm time and charging time
With radio on: time, page & memory address, SW meter band displays.
SW meter band indicator
PAGE: Memory Page number
PRESET: Memory Address number
Alarm Timer A or B - On/Off indicator
Key-Lock indicator
Synchronous band detection
Single Side Band (SSB) indicator
USB: Upper Side Band
LSB: Lower Side Band
Tuning Speed:
Slow: Slow Tuning
Fast: Fast Tuning
KHz: frequency unit for MW, LW & SW
MHz: frequency unit for FM
AM Band width indicator
: AM Wide band
: AM Narrow band
FM, MW,LW and SW Band indicator
FM Stereo indicator
Air Band indicator
Ni-MH Rechargeable Battery indicator
PL-680
HOW TO TURN ON/OFF THE RADIO
1. Open the battery compartment located on the back of the unit; install 4 x UM3 AA size batteries observing the battery polarity diagram on the back of the radio. Close the battery door.
Connect the unit to the regulated power supply.
+
2. Press the [POWER] button to turn on the radio.
Press
Note:
If the radio is unable to power on, please check if the batteries are installed correctly, battery capacity is sufficient, and the key lock function is turned off; to deactivate the key lock function press & hold the [ ] button.
Long press the power button to adjust the sleep timer setting.
PL-680 5
TUNING INTO STATIONS
Press the [POWER] button to turn on your radio, then select your desired band by pressing [FM], [AM], SW [ ] / [ ], or [AIR] button.
In case of receiving FM/AIR/SW broadcasting, fully extend the telescopic antenna for a better reception. When receiving MW and
LW broadcasting, please rotate the radio or change its location to achieve optimum reception. You can rotate the [VOLUME] knob to adjust to an appropriate volume.
Now, you can turn into your favorite stations with any of the below tuning methods:
METHOD 1: MANUAL STATION TUNING
Press the [VF/VM] button to enter the frequency mode (VF), the frequency display flashes twice. Now rotate the
[TUNING] knob to select your desired station.
Ni-MH
Battery
0 1 2 3 4 5
FM
SL EEP flashing
MHz
Frequency mode
METHOD 2: AUTO BROWSE STATION
1. Press the [VF/VM] button to enter the
frequency mode (VF), the frequency
display flashes twice.
2. Press & hold the [VF/VM] button to
browse to the next available station,
pre-listening the station for five
seconds before continuing to browse.
3. To stop the auto browse function,
simply rotate the [TUNING] knob or
press on the [VF / VM] button again
to confirm on your desired station.
Searching
Frequency
Ni-MH
Battery
0 1 2 3 4 5
SL EEP flashing
FAST
MHz
FM
Auto browse station
Notes:
1. While operating the “Auto Browse Station” function, you can press
the [MEMORY] button anytime to store the station into memory,
and the radio will keep on auto browsing the next available
station.
2. The "Auto Browse Station" function is not available for Air Band
and SW SSB frequencies.
6 PL-680
TUNE IN STATIONS
METHOD 3: DIRECT KEYPAD ENTRY
1. Press the [VF/VM] button to enter the frequency mode (VF), the
frequency display flashes twice.
2. Press the numeric keys [0] - [9] to enter the station frequency
directly.
Notes:
1. Ignore the decimal point for FM band when inputting the
frequency numbers. For example, FM 89.3 MHz, just enter
8 9 3 .
2. If the entered frequency is not within the covered range, an error
symbol " " is displayed.
PL-680 7
WORKING WITH STATION MEMORIES
The PL-680 has 2000 station memories, which are organized over
12 memory pages.
1. Memory PAGE 0, noted as [P0], consists of 800 memories, 100
assigned for FM/MW/LW, 200 for SW & SSB and 100 for AIR
BAND.
2. Memory PAGE 1~12, noted as P1, P2, etc., each page consists of
100 memories, in total 2000 memories.
BAND
MEMORY
FM
MW
LW
SW
SSB
AIR
Memory for each Band ( 800)
PAGE P0
100
100
100
200
200
100
ATS
Memory among all Band (1200)
PAGE 01 -12
Each Memory
Page can store
100 Memories.
ATS
ATS is available for all Memory
Pages (except
Air Band)
METHOD 1: STORING STATIONS MANUALLY
1. Press the [FM], [AM] (for MW and LW) or [SW] button for band
selection, then tune into your desired station.
2. Press the [MEMORY] button; the next available memory position
flashes.
3. Rotate the [TUNING] knob to specify your preferred memory
position.
4. Press the [MEMORY] button again to confirm. You can also wait
for 3 seconds to auto store the station into memory.
NOTE: To store the station in a different memory page, press the
[ - PAGE + ] button.
METHOD 2:
SEMI-AUTOMATIC STATION STORAGE
While operating the “Auto Browse
Station” (refer to page 06) function, you can simply press the [MEMORY] button to store the station into memory to avoid unwanted stations.
Ni-MH
Battery
0
Searching
Frequency
FM
1 2 3 4 5 flashing
FAST
MHz
Auto browse station
8 PL-680
WORKING WITH STATION MEMORIES
METHOD 3: ATS (AUTO TUNING STORAGE)
FM ATS:
1. Fully extend the telescopic antenna
and press the [FM] button to select
FM band.
2. To automatically store all available
stations, press & hold the [FM] button;
Ni-MH
Battery
0 1 2 3 4 5
SL EEP
PAGE
"PRESET" will flash in the top right
corner of the display while the frequency
FM
starts running. The frequency stops running once the ATS
MHz flashing
PRESET
operation has completed. Rotate the [TUNING] knob to browse
all stored FM stations.
MW/LW ATS:
1. Press the [AM] button to select MW/LW band.
2. Press & hold the [AM] button to perform ATS on the MW or LW
band.
SW ATS:
Fully extend the telescopic antenna and press the SW [ ] or [ ] button to select SW band. There are two modes for SW ATS tuning:
Mode A: Press & hold the [ ] button to ATS the stations within all
meter bands
Mode B: Press & hold the [ ] button to ATS the stations within
present meter band only.
Notes:
1. While performing ATS in FM, MW/LW or SW (mode A) bands,
previously stored stations are replaced by the newly found
stations.
2. While performing ATS in SW (mode B) band, previously stored
stations are not replaced. Instead, all newly found stations are
stored in blank memory positions.
3. If the surrounding area has too much interference or many
mirror/blank stations are stored during ATS, try to contract the
telescopic antenna (for FM and SW) or rotate the radio (for MW
and LW). Also try to push the [ANT. GAIN] switch into "NORMAL"
or "LOCAL" position. Then perform ATS again.
PL-680 9
WORKING WITH STATION MEMORIES
DELETE MEMORY
Press the [VF/VM] button to enter the memory mode; the memory address shows in the upper right corner of the display.
METHOD 1: DELETE SINGLE MEMORY
Rotate the [TUNING] knob to select the memory that you want to delete, press & hold the [DELETE] button with “ ” flashing; then press the
[DELETE] button to remove the unwanted memory address.
Ni-MH
Battery
0 1 2 3 4 5 flashing
PAGE PRESET
Note: Delete Single Memory
If “ " is flashing more than 3 seconds without confirmation, it will exit the delete function automatically.
METHOD 2: SEMI-AUTO DELETE MEMORY
Press and hold the [VF / VM] to auto browse stations, then you can press the [DELETE] button anytime to direct delete the unwanted station; the radio will keep on auto browsing the next available station until you press any other button to stop this function.
METHOD 3: DELETE ALL MEMORIES WITHIN A PAGE
Press & hold the [DELETE] button for
3 seconds and notice both “Memory flashing address” & “ ” flashing, then follow with “Memory Page” and “ ” flashing on the upper right corner of display.
Press the [DELETE] button again to delete all memory within the selected
Ni-MH
Battery
0 1 2 3 4 5
PAGE PRESET page.
Delete ALL Memory
Note:
If the [DELETE] button has not been pressed within 3 seconds to confirm, it will exit the delete function automatically.
10 PL-680
WORKING WITH STATION MEMORIES
AUTO SORTING MEMORY
To sort all stored stations automatically, turn the device off, then press and hold the [ ] button for 2 seconds until the memory page number in the upper right corner starts running.
This function is able to:
1. Remove duplicate stations. Especially useful after storing stations manually, as you might store a station more than once.
2. Sorting the sequence of stored stations.
– In page P0, select your desired band to find all stored stations in
sequence of frequency (from low to high).
– In page 01-12, all stored stations are sorted in band sequence
(FM, SW, MW, Air band, LW) and placed in sequence of frequency
(from low to high).
PL-680 11
LISTENING TO STORED STATIONS
Select the band of your desired station, then press the [VF/VM] button to enter the memory mode; the memory address shows in the upper right corner of the display. Press the [- PAGE +] button to select the memory page in which to search for stored stations using any of the below memory tuning methods.
Ni-MH
Battery
0 1 2 3 4 5
MW
SL EEP
BW flashing
PAGE kHz
PRESET
Changing memory pages
METHOD 1: MANUAL MEMORY TUNING
Rotate the [TUNING] knob to tune around the stored stations.
METHOD 2: AUTO BROWSE MEMORY
Press & hold the [VF/VM] button to browse to the next stored station, pre-listening each station for five seconds before continuing to browse.
Ni-MH
Battery
While browsing, "PRESET" flashes on the display. To stop browsing, rotate the [TUNING] knob or press the
[VF/VM] button again.
0
FM
1 2 3 4 5
SL EEP
PAGE
MHz
Auto browse memory
PRESET flashing
METHOD 3: DIRECT KEY IN MEMORY ADDRESS
Press the numeric keys [0] - [9] to enter the memory address directly, and then press the button to confirm.
Note: If the display shows “ ” symbol after entering the number, it means the entered memory page/address does not exist.
12 PL-680
SLEEP FUNCTION
1. In POWER OFF mode, press &
hold the [POWER] button untill
SL EEP the sleep timer symbol " "
flashes on the display.
flashing
Ni-MH
Battery
0 1 2 3 4 5
SL EEP
2. Rotate the [TUNING] knob
immediately to select a sleep
timer from 1 - 120 minutes or
select " " for POWER ON
mode (the radio will be turned
on after 1 second).
Time selection for sleep timer
Note: The default setting of the sleep timer is "ON ".
TIME SETTING
1. Press & hold the [TIME] button until
the hours indicator starts flashing.
Rotate the [TUNING] knob to adjust
the hours, or directly input the time
by pressing the [ 0 – 9 ] numeric keys.
2. While the hours indicator is flashing,
press the [TIME] button again to
select the minutes indicator.
Rotate the [TUNING] knob to adjust
the minutes, or directly enter it by
pressing the [0 – 9] numeric keys.
3. Short press the [TIME] button to confirm,
or wait for 3 seconds to automatically
confirm the time setting.
Ni-MH
Battery flashing
Timer A
Time setting
PL-680 13
ALARM SETTING (By Radio only)
SETTING THE ALARM STATION:
1. Turn on the radio, then tune into your favorite station and adjust
your desired alarm volume level.
2. Press the [MEMORY] button and then immediately press the
flashing on the display to confirm the preset alarm station.
SETTING THE ALARM TIME
1. Press & hold the [TIMER A] button
until the hours indicator starts
flashing in the upper right corner of
the display. Rotate the [TUNING]
knob to adjust the hours, or directly
enter the alarm time by pressing the
[ 0 – 9 ] numeric keys.
2. While the hours indicator flashes,
press the [TIMER A] button to select
the minutes indicator. Rotate the
[TUNING] knob to adjust the minutes,
or directly enter it by pressing the
[ 0 – 9 ] numeric keys.
3. Press the [TIMER A] button again,
then rotate the [TUNING] knob to
select from 1 - 90 minutes to set the
"Alarm Off Timer". This is the time
duration after which the radio will be
turned off automatically.
Ni-MH
Battery flashing
SL EEP
Timer A
A
Setting timer for alarm off
4. Press the [ALARM] button to confirm
the setting or wait for 3 seconds, the
unit will automatically confirm the
alarm setting.
Note: Follow the above instructions using the [TIMER B] button to
set a second alarm.
14 PL-680
SNOOZE FUNCTION
When the alarm goes off, press the [LIGHT/SNOOZE] button to temporarily turn off the alarm. The alarm will go off again after 5 minutes.
Notes:
1. To turn off/on the alarm, press the [TIMER A] or [TIMER B] button;
2. When the alarm goes off, press the [POWER] button once to
deactivate the "Alarm Off Timer"; press it twice to turn off the
radio.
3. If the preset alarm is activated when you are listening to the radio,
it will automatically switch to that station when the alarm goes off.
INTELLIGENT LIGHT FUNCTION
This device has an intelligent backlight function, meaning the backlight is lid for about 5 seconds after operating any keys or knobs.
TURN ON/OFF THE BACKLIGHT:
Press the [LIGHT/SNOOZE] button to illuminate the LCD for 30 seconds. Press it again to turn off the backlight.
Notes:
1. When the unit is powered by batteries, to reduce power
consumption, please try to avoid setting the backlight to 30-
seconds illumination.
2. When the unit is turned off, the 30-seconds illumination function is
turned off as well.
PL-680 15
TUNING STEP SETTINGS
There are three tuning step speed settings: slow, fast, and intelligent (slow & fast). In Frequency Mode (VF), press & hold the [STEP] button to select your preferred setting. flashing
The intelligent tuning step notices when you rotate the [TUNING] knob in a slow or fast way. When rotating fast, the tuning steps will be larger.
NOTE: intelligent tuning step is not available for Air Band.
Long-press
BAND
TUNING
STEP
FM
MW
LW
SW
AIR
SLOW TUNING STEPS
Slowly rotate the [TUNING] knob
0.01 MHz
1kHz
1kHz
1kHz
1kHz
FAST TUNING STEPS
Quickly rotate the [TUNING] knob
0.1MHz
9kHz / 10kHz
9kHz
5kHz
25kHz
FM ST. (FM STEREO)
1. When listening to radio broadcastings through stereo earphones,
press the [FM.ST] button to activate the stereo function; the " "
symbol appears on the display. If the FM signal is too weak, it is
advised to turn off the stereo function by pressing the [FM ST.]
button again; the " " symbol disappears.
2. When listening to FM stereo through a speaker, it is advised to
turn off the stereo function to improve sound quality.
3. The stereo function will not be activated and the " " symbol
will not appear if the FM station is not in stereo broadcasting.
16 PL-680
AM BW (BANDWIDTH)
Press the [AM BW] button to select your desired bandwidth for MW,
LW, SW, and SSB.
Wide Band
It has better audio fidelity when receiving strong signals or local stations.
Narrow Band
It is suitable to receive weak and long distance stations as the narrow band is able to limit the interference from adjacent strong signals and reduce background noise.
ANT. GAIN
Ni-MH
Battery
0 1 2 3 4 5
SL EEP
Shortwave BW kHz
AM Bandwidth Indicator
While listening to SW, push the
[ANT.GAIN] switch to "DX" position for normal listening. For stations with a strong signal or strong electrical interference, push the [ANT.GAIN] switch to either
"NORMAL" or "LOCAL" to achieve better sensitivity.
TONE CONTROL
ANT. GAIN
DX
NORMAL
LOCAL
TONE
TREBLE
BASS
Push the [TONE] switch upward for “TREBLE” listening, downward or “BASS” tone.
KEY LOCK FUNCTION
To activate the key lock function, press & hold the [ ] button; the " " symbol appears on the display.
Press & hold the [ ] button again to unlock.
PL-680 17
INTELLIGENT CHARGING FUNCTION
In power off mode, install 4 x UM3 (AA size) rechargeable (Ni-MH) batteries to activate the built-in charging function. Connect the external adaptor to start charging the batteries. The symbol " " will advance from down to up while charging. It stops when the batteries are fully charged.
When using non-rechargeable batteries, please turn off the charging function; press & hold the [BATTERY] button, the " " symbol disappears from the display.
Notes:
1. Before using new Ni-MH rechargeable batteries for the first time,
please charge them overnight. This will increase battery life.
2. Do not use batteries of different capacities at the same time.
3. Do not try to charge non-rechargeable batteries. This will damage
both the batteries and the device.
4. Please do not use an external adaptor with a different voltage, this
will damage the device.
5. When charging, if the external power adapter and the battery cover
become hot, this is normal.
SINGLE SIDE BAND (SSB)
1. In Shortwave mode, press the [SSB] button repeatedly to select
Upper Side Band (USB) or Lower Side Band (LSB).
“ USB” showing on the display indicates USB selection.
“ USB” and “LSB” disappearing means switching to SW.
2. Enter the SSB frequency directly by pressing the numeric keys
[0 – 9].
3. Then fine tune the [SSB BFO] knob to achieve better sound fidelity.
18 PL-680
SYNCHRONOUS DETECTOR
When receiving AM broadcasting, if there is interference from adjacent strong signals, you can activate the SYNC function to improve the reception.
optimum reception.
2. To deactivate the SYNC function, press the [SYNC] button until
Notes: If the "SYNC" symbol keeps flashing, this indicates that the
radio signal is too weak or the frequency is deviant. It is
recommended to deactivate synchronous detection as it is
unable to function properly.
HOW TO IMPROVE FM / SW RECEPTION
Use the external wire antenna to plug into the [FM & SW ANTENNA] jack, then position the opposite end outside the window for better FM and SW reception.
external antenna for FM & SW
Window wall
FM & SW ANTENNA
Caution: Do not place the external antenna outdoors during a thunderstorm!
PL-680 19
SYSTEM SETTINGS (In Power Off Mode)
SETTING FM FREQUENCY RANGE:
Press & hold the [FM SET] button until 88-108MHz, 76-108MHz or 87-108MHz appears on the display. Press the [FM SET] button to select a suitable frequency range for FM.
TURN ON/OFF THE LW:
To turn ON/OFF LW, press & hold the [LW ON/OFF] button until "LW
ON" or "LW OFF" appears on the display.
SETTING MW (AM) TUNING STEP:
To select your desired AM tuning steps, press & hold the [9/10kHz] button until "9kHz" or "10kHz" appears on the display.
TURN ON/OFF THE INTELLIGENT LIGHT FUNCTION
The Intelligent Light Function is activated by default, which will illuminate the backlight for 5 seconds after operating any button or knob. To deactivate, press & hold the [LIGHT SET] button until "OFF" appears on the display; repeat the operation to reactivate.
Note: After deactivating the Intelligent Light Function, the
[LIGHT/SNOOZE] button can still be used to turn on/off the
back light.
TURN ON/OFF THE CHARGING FUNCTION
Using Regular Batteries for power supply:
In radio off mode, press & hold the [BATTERY] button until "CHA
OFF" is shown on the display. When the charging mode is deactivated, "Ni-MH Battery" does not appear below the battery consumption indicator.
Using Rechargeable Batteries for power supply:
In radio off mode, press & hold the [BATTERY] button until "CHA ON" is shown on the display. When the charging mode is activated,
“Ni-MH Battery" appears below the battery consumption indicator.
Note: The default setting is for using rechargeable batteries. For a
correct battery power indication when using regular batteries,
deactivate the charging function.
20 PL-680
RESET PROCEDURE
If not functioning properly, you can reset the device by sticking a pointed object (such as a straightened paper clip) into the reset hole and gently press the [RESET] button.
Note: Resetting the device will not delete any station memories.
IMPORTANT MATTERS FOR USING BATTERIES
1. When the device is not powered by batteries or the adaptor for a
long time, the clock setting is lost, but the stored radio stations
are saved.
2. When battery power is low, the " " symbol starts flashing to
alert you to charge the batteries or change to new ones. The
device turns off automatically when all power is gone.
3. Do not mix new and used batteries, this may damage the radio
and display an incorrect power capacity.
4. In order to avoid leakage, always remove the batteries when the
unit will not be used for a long period of time.
PL-680 21
TROUBLE SHOOTING
QUESTIONS ANSWERS SOLUTIONS
Cannot turn on the radio.
- Batteries have no
power
- Batteries are installed
incorrectly.
- Key lock function is
activated.
- Replace all batteries with new ones.
- Take note of the correct
polarity direction, then
reinstall the batteries.
- Press the [ ] button
to deactivated it.
Radio turns off while listening.
- Batteries have no
power
- Sleep timer is
activated.
- Replace or charge all
batteries.
-Turn the radio on again.
During ATS, some stations cannot be stored.
Some stored stations have noise.
- Frequency of stations
is too weak.
- There is interference
near by your area.
- Search the station
manually.
- Contract the antenna or
move to other location
and try again.
Only few FM stations can be received.
- FM frequency may
have been set to
76 - 90MHz
accidentally.
- Turn off the radio, press
& hold the [FM SET]
button to select the
accurate FM frequency
range.
Poor AM reception in
USA.
- USA uses 10kHz AM
tuning steps, the
device may still be set
to 9kHz.
- Turn off the radio
press the [9/10kHz]
button to select
accurate tuning step.
The sound of SW
SSB broadcasting is too low.
The default bandwidth is Narrow band.
Press the [AM BW] button to select the Wide band.
22 PL-680
TROUBLE SHOOTING
QUESTIONS ANSWERS SOLUTIONS
When the alarm goes off, there is only noise in the broadcasting.
-Did not set the proper radio station for the alarm.
-Or there is no
broadcasting at that
frequency.
-Preset your alarm
station properly
-Make sure it is possible
to receive radio
broadcastings at your
location.
The charging time becomes shorter and shorter.
The rechargeable batteries are getting old.
Replace the old rechargeable batteries with new ones.
Radio malfunction.
There may be some form of interference, causing the microchip to not function properly.
Remove the batteries.
Reinstall the batteries once the device's display has turned off completely.
If the device is still not working, please press the reset button with a pointed object.
PL-680 23
SPECIFICATIONS
1. Frequency Range:
FM: 76~108 / 87~108 MHz Step: 0.01MHz /0.1 MHz
MW: 522~1620 / 520~1710 kHz
Tuning Step: 9K for North America or other countries/10K for South America
LW: 100~519 kHz Step: 1 kHz/ 9 kHz
SW: 1711~29999 kHz Step: 1 kHz/ 5 kHz
AIR:118~137MHz Step: 1kHz / 25 kHz
2. Sensitivity
FM (S/N=30dB) Less than 3uV
MW (S/N=26dB) Less than 1mV/m
LW (S/N=26dB) Less than 5mV/m
SW (S/N=26dB) Less than 20uV
SSB(S/N=10dB) Less than 1uV
AIR (S/N=10dB) Less than 5uv
3. Selectivity
FM > 30 dB (±200kHz)
MW/LW > 40 dB (±9kHz )
SW > 40 dB (±5kHz
4. S/N Ratio
FM Less than 60dB
MW/LW Less than 45dB
SW Less than 50dB
5. AM Frequency
SSB, AM 1st IF: 55.845MHz
2nd IF: 455 kHz
FM: 10.7MHz
6. FM Stereo crosstalk Less than 20 dB
7. Output Power
Speaker ≥ 450 mW
Earphone ≥ 10 mW
24 PL-680
advertisement
Related manuals
advertisement
Table of contents
- 7 HOW TO TURN ON/OFF THE RADIO
- 8 TUNING INTO STATIONS
- 10 WORKING WITH STATION MEMORIES
- 14 LISTENING TO STORED STATIONS
- 15 SLEEP FUNCTION
- 15 TIME SETTING
- 16 ALARM SETTING
- 17 SNOOZE FUNCTION
- 17 INTELLIGENT LIGHT FUNCTION
- 18 SETTINGS
- 18 FM ST. (FM STEREO)
- 19 ANT. GAIN
- 19 TONE CONTROL
- 19 KEY-LOCK FUNCTION
- 20 SINGLE SIDE BAND (SSB)
- 21 HOW TO IMPROVE FM / SW RECEPTION
- 23 RESET PROCEDURE
- 24 TROUBLE SHOOTING
- 25 SPECIFICATIONS