- Computers & electronics
- Computer components
- Chassis components
- Computer cases
- Fantec
- 1332
- Data Sheet
advertisement
FANTEC SRC-2180X03
2U STORAGE RACKMOUNT CHASSIS
8x 3.5" SATA/SAS BACKPLANE SLOTS
FANTEC SRC-SERIE
STORAGE RACKMOUNT CHASSIS
I. Specification:
Support SAS interface: for 3G backward compatibility.
Support SATA interface: for 3G backward compatibility.
Support hard disk 29pin female SAS and SATA II compatibility.
Support 4 pcs 7 pin lock male blue connector for host card SAS primary port or SATA II input port.
Support 4 pcs 7 pin lock male black connector for host card SAS secondary port.
Support 4 port hard disk inrush current control and mosfet IC for Hot-swapping.
Support hard disk DC +12V, +5V and +3.3V.
Support 4 pcs 0603 SMD blue LED light on for hard disk insert.
Support 4 pcs 0603 SMD red LED blink for hard disk access.
(SATA ready is high active, and SAS ready is low active)
Support 2 pcs power 180 deg big 4-pin D-type connectors.
Support 4 pcs external FAN speed monitoring and FAN failure buzzer alarm. (Buzzer on board).
Support FAN fail SMD LED active shown and external pin header.
Support FAN fail buzzer alarm external pin header.
Support external 2X2 pin header for FAN fail LED and mute switch.
Minimum Fan Speed Detection: The FAN IC fail frequency is below 40 Hz, which corresponds to a fan speed of approximately 1200 rpm.
The fan remains powered during a locked rotor or an under-speed failure condition.
-01-
2. Pin Assignment:
interface side
D C D C D C
D C A A
B
A
A
Fan1, Fan2, Fan3, Fan4 3 pin wafer for FAN monitor pin out
E
A
3 2 1 3 : Tech
B
JP1,JP2 big 4P pin out
2 : +12V
1
VDD +12V
1 2 3 4
1 : GND
2
GND
3
GND
4
VCC +5V
C J5 ,J7 ,J9 and J11 SAS primary connector Pin Output
7 pin SATA II blue connector.
For HBA SAS primary port or SATA II 3G host card.
1
2 3 5
4
6
7
1
GND
2
RP+
3
RP-
4
GND
5
TP-
6
TP+
7
GND
D
J6 ,J8 ,J10 and J12 SAS secondary connector Pin Output
7 pin SATA II black connector
Only HBA SAS secondary port connector to host card
1
2 3
4
5 6
7
1
GND
2
RS+
3
RS-
4
GND
5
TS-
6
TS+
7
GND
E
S1 DIP Switch pin out
Switch
ON
OFF
SW1 Sw2
55 C Mute enable
60 C Mute disable
-02-
2-1. Pin Assignment:
interface side
F
JP4 External 2 X 2 Pin out
3 Mout switch+ 4 GND
For fail buzzer alarm mute insert pin 3-4.
1 Fan fail LED+ 2 Fan fail LED-
For FAN fail LED insert pin 1-2.
G
F
G
JP3 4 X 4 pin 2.54mm 180deg header pin out.
13 9 5 1
14 10 6 2
15 11 7 3
16 12 8 4
1
2
3
4
13
14
Card acces LED4-
15
16
Card acces LED4+
HDD4 p11 pin
GND
9
10
Card acces LED3-
11
HDD4 p11 pin
12
Card acces LED3+
GND
5
Card acces LED2+
6
Card acces LED2-
7
HDD4 p11 pin
8
GND
1
Card acces LED1+
2
Card acces LED1-
3
HDD4 p11 pin
4
GND
Default setting is insert short jumper to pin 2-3, 6-7, 10-11, 14-15 for
HDD access support.
If you need HBA card in put access LED, please remove short jumper, insert pin 1-2, 5-6, 9-10,13-14.
13 9 5 1
14 10 6 2
15 11 7 3
16 12 8 4
13 9 5 1
14 10 6 2
15 11 7 3
16 12 8 4
If you need HDD motor spin function, please insert short jumper to pin 3-4, 7-8, 11-12, 15-16
13 9 5 1
14 10 6 2
15 11 7 3
16 12 8 4
-03-
2-2. Pin Assignment:
H.D.D side
H H H
H
H
J1, J2, J3, J4 2 29pin female SAS and SATA II connector pin out
S1
S8
P1
P8
P1 5
GND
GND
V33
V5
V12
S2
S9
P2
P9
RP+
RS+
V33
V5
S3
S1 0
P3
P1 0
RP-
RS-
V3C
GND
S4
S1 1
P4
P1
GND
GND
GND
1 LED
S5
S1 2
P5
P1 2
TP-
TS-
GND
V-gate
S6
S1 3
P6
P1 3
TP+
TS+
GND
V12C
S7
S1 4
P7
P1 4
GND
GND
V5C
V12
-04-
-
05
-
Product details
Model no.:
Specification:
Drive bays:
Mainboard type:
Cooling:
Switch:
Controls:
Slot opening:
Riser card:
Backplane:
Speaker:
SRC-2180X 2U 8xSAS&SATA Backplane
2U IPC 660mm black aluminium open: 8x3,5" SATA/SAS hot swap, 1x5,25" Slim, 1x3,5 Slim" internal: 2x 2,5", 1x 3,5"
E-ATX / ATX / M-ATX (12" x 13")
4x 80mm hot-swap fans + 1x 90mm blower fan
ON/OFF switch, system & alarm reset
LED's for ON/OFF switch and HDD-access
3 open slots at rear panel
Riser card with 3 PCI slots
8x SATA 3Gbit / SAS / SATA
0,4W built in
Material/ color of chassis: 1,2mm SGCC zinc-coated steel black
Material/ color of front bezel: anodized aluminium black / blue
Material/ color of handle: steel / silver
Front connectors:
Accessories including:
2x USB connectors
2x Firewire connectors
2x Ethernet RJ45 connectors
USB connector cable with circuit diagram
PCI riser card with 3 PCI slots, 32bit screws
Power supply:
Optional accessories: without power supply (optional) sliding rails package: SRC-SR26"
Consists of 2x 26" mounting rails
Dimensions (w x d x h): 481 x 660 x 89 mm
Certifications:
Weight / piece (kg):
FCC, CE, RoHS
13
Package (piece / carton): 1
Description: 19" industrial PC chassis for installation in 19" rackmount cabinet.
Rugged construction and high-grade processing.
Technical details are subject to changes.
Technical details are subject to changes.
-
06
-
-
07
-
advertisement
Related manuals
advertisement