Installation and Assembly:
Wall Mount
Model: DS-VW650
Parts List
Description
A wall plate
B lock bracket
C vertical bracket
D M5 x 10 mm socket pin Type F screw
E #14 x 2.5" hex head wood screw
F concrete anchor
G 4 mm allen wrench
H nylon shoulder washer
I M6 x 12 mm phillips screw
J M8 x 15 mm phillips screw
Qty.
1
4
6
6
4
4
2
2
1
1
Part #
145-1199
145-1201
145-1200
520-1164
5S1-015-C03
590-0320
560-9646
590-2233
5201128
520-9257
D E
H I J
F
A B
G
C
Visit the Peerless Web Site at www.peerlessmounts.com
1 of 4 ISSUED: 09-24-10 SHEET #: 125-9146-1
Installation to Wall Stud
WARNING
• Installer must verify that the supporting surface will safely support the combined load of the equipment and all attached hardware and components.
• Tighten wood screws so that wall plate is firmly attac hed, but do not overtighten. Overtightening can damage the screws, greatly reducing their holding power.
• Never tighten in excess of 80 in. • lb (9 N.M.).
• Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud finder is highly recommended.
• Hardware provided is for attachment of mount through standard thickness drywall or plaster into wood studs. Installers are responsible to provide hardware for other types of mounting situations.
1
Use a stud finder to locate the edges of the stud. Use of an edge-to-edge stud finder is highly recommended.
Based on their edges, draw a vertical line down the stud center. Place wall plate ( A) on wall as a template.
Level plate, and mark the center of the six mounting holes. Make sure that the mounting holes are on the stud centerline. Drill six 5/32" (4 mm) dia. holes 2-1/2" (65 mm) deep. Make sure that the wall plate ( A) is level, secure it using six #14 x 2.5" wood screws ( E) as shown below.
Stud
A
E
Visit the Peerless Web Site at www.peerlessmounts.com
2 of 4 ISSUED: 09-24-10 SHEET #: 125-9146-1
Installation to Solid Concrete or Cinder Block
WARNING
• When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" (35 mm) of actual concrete thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid part of the block, generally 1" (25 mm) minimum from the side of the block. Cinder block must meet ASTM
C-90 specifications. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a hammer drill to avoid breaking out the back of the hole when entering a void or cavity.
• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.
• Make sure that the wall will safely support four times the combined load of the equipment and all attached hardware and components.
solid concrete
1
Make sure that wall plate ( A) is level, use it as a template to mark six mounting holes. Drill six 5/16”
(8mm) dia. holes to a minimum depth of 2.5” (64 mm). Insert anchors ( F) in holes flush with wall as shown (right). Place wall plate ( A) over anchors and secure with six #14 x 2.5” screws ( E) as shown.
Level, then tighten all fasteners.
E
F cinder block
WARNING
• Tighten screws so that wall plate is firmly attached, but do not overtighten. Overtightening can damage screws, greatly reducing their holding power.
• Never tighten in excess of 80 in. • lb (9 N.M.).
• Always attach concrete expansion anchors directly to load-bearing concrete.
• Never attach concrete expansion anchors to concrete covered with plaster, drywall, or other finishing material. If mounting to concrete surfaces covered with a finishing surface is unavoidable, the finishing surface must be counter bored as shown below. Be sure concrete anchors do not pull away from concrete when tightening screws. If plaster/drywall is thicker than 5/8" (16 mm), custom fasteners must be supplied by installer wall plate
INCORRECT concrete wall plate
CORRECT concrete plaster/ dry wall plaster/ dry wall
A
1
F concrete surface
Drill holes and insert anchors ( F).
2
A
E F
Place plate ( A) over anchors (E) and secure with screws (F).
3
Tighten all fasteners.
Visit the Peerless Web Site at www.peerlessmounts.com
3 of 4 ISSUED: 09-24-10 SHEET #: 125-9146-1
2 Attach adapter brackets ( C) to display using four M6 x 12 mm phillips screw (I) with nylon shoulder washers (H), or using four M8 x 15 mm phillips screws ( J).
I or J
H
C
DISPLAY
Attaching Adapter Brackets to Wall Plate
3 Hook adapter brackets ( C) to wall plate (A). Slide adapter brackets (C) to position.
Once display is located in desired position, secure with lock bracket ( B) using two M5 x 10 mm socket pin Type F screws ( D) to lock in place as shown in figure 3.2.
DISPLAY
C
B
A
D
Figure. 3.1
BACK FOR WALL PLATE
SUPPORTING SURFACE
NOT SHOWN FOR CLARITY
A
Visit the Peerless Web Site at www.peerlessmounts.com
Figure. 3.1
4 of 4 ISSUED: 09-24-10 SHEET #: 125-9146-1
© 2010 Peerless Industries, Inc. All rights reserved.
All other brand and product names are trademarks or registered trademarks of their respective owners.
