MESSOA Maven Indoor Dome Network Camera, Outdoor IR Dome Network Camera, Fixed Network Camera, IR Bullet Network Camera, Flat Mini Dome Network Camera network camera User Manual

Network Camera

Maven Series

User

Manual

201407 A2

Table of Contents

1 Network Deployment

1.1

Network Topology

1.2

Connection

1.2.1 Checking Appearance

1.2.2 Default IP address

1.2.3 Connecting from a computer & Viewing Preparation

1.3

IP Finder

2 Administration and Configuration

2.1

Live View

2.1.1 Model Reference Table

2.2

Configuration

2.2.1 Information

2.2.2 Image Parameter

2.2.3 Network Settings

2.2.4 Account Management

2.2.5 Event Settings

2.2.6 Record Settings

2.2.7 System Settings

2.2.8 Event Log

Appendix A: Specifications of Indoor Dome Network Camera (Manual Focus Model)

Appendix B: Specifications of Indoor Dome Network Camera (Motorized Lens Model)

Appendix C: Specifications of Outdoor IR Dome Network Camera

Appendix D: Specifications of Fixed Network Camera

Appendix E: Specifications of IR Bullet Network Camera

Appendix F: Specifications of Flat Mini Dome Network Camera

10

10

12

13

13

13

20

24

25

28

30

32

33

35

37

39

41

43

5

5

5

5

9

4

4

1

WARNING

● The unit operates at DC 12V/AC 24V/ PoE (for Indoor Dome Network Camera & Fixed Network Camera), AC 24V/ PoE (for

Outdoor IR Dome Network Camera & IR Bullet Network Camera).

● Installation and service should be performed only by qualified and experienced technicians and comply with all local codes and rules to maintain your warranty.

● To reduce the risk of fire or electric shock, do not expose the product to rain or moisture.

● Wipe the camera with a dry soft cloth. For tough stains, slightly apply with diluted neutral detergent and wipe with a dry soft cloth.

● Do not apply benzene or thinner to the camera, which may cause the surface of unit to be melted or lens fogged.

● Avoid aligning the lens to very bright objects (example, light fixtures) for long periods of time.

● Avoid operating or storing the unit in the following locations:

• Extremely humid, dusty, or hot/cold environments [ Recommended operating temperature: -10°C to +50°C, (for Indoor

Dome Network Camera & Fixed Network Camera), -40°C to +50°C (for Outdoor IR Dome Network Camera & IR Bullet

Network Camera)]

• Close to sources of powerful radio or TV transmitters

• Close to fluorescent lamps or objects with reflections

• Under unstable or flickering light sources

WEEE (Waste Electrical and Electronic Equipment). Correct disposal of this product (applicable in the

European Union and other European countries with separate collection systems). This product should be disposed of, at the end of its useful life, as per applicable local laws, regulations, and procedures.

Get Started

This user manual is designed as a reference for the installation and manipulations of the unit including the camera’s features, functions, and detailed explanation of the menu tree. Please read this manual thoroughly and save it for future use before attempting to connect or operate the unit. The reader is supposed to be able to get the following information in this manual.

● Product Overview: the main functions and system requirements of the unit.

● Installation and Connection: instructions on unit installation and wire connections.

● Administration and Configuration: the main menu navigation and controls explanations.

2

FCC Compliance Statement

Information to the user: This unit has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This unit generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this unit does cause harmful interference to radio or television reception, which can be determined by turning the unit off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

● Reorient or relocate the receiving antenna.

● Increase the separation between the unit and receiver.

● Connect the unit to an outlet on a circuit different from that to which the receiver is connected.

● Consult the dealer or an experienced radio/TV technician for help.

Caution

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the unit.

CE Statement

Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The manufacturer declares that the unit supplied with this guide is compliant with the essential protection requirements of EMC directive and General Product Safety Directive GPSD conforming to requirements of standards EN55022 for emission, EN 55024 for immunity, EN 300 and EN 328 for WIFI.

3

1 Network Deployment

1.1

Network Topology

The unit, which is equipped with Ethernet RJ-45 network interface, can deliver video images and audio in real time via either

Internet or Intranet. Please refer to the skeleton drawings shown below for understanding. (Here takes Indoor Dome Network

Camera as the example in the illustration.)

Figure 1 - 1: Network Topology Type 1

Figure 1 - 2: Network Topology Type 2

4

1.2

Connection

1.2.1 Checking Appearance

Below table lists the minimum requirement to implement and operate the unit. No hardware/software component inferior to the requirements is recommended.

Table 1 - 1: System Requirements

System Hardware

CPU

RAM

Display

System Software

Operating System

Browser

Unit

Intel Pentium 4 2.4GHz or equivalent

1 GB or above

NVIDIA GeForce 6 Series or ATI Mobility Radeon 9500

Microsoft Windows XP, Windows Vista, or Windows 7

Microsoft Internet Explorer 8 or above, Chrome, Firefox

Power Supply

DC 12V / AC 24V / PoE(for Indoor Dome Network Camera & Fixed Network Camera)

AC 24V/ PoE (for Outdoor IR Dome Network Camera & IR Bullet Network Camera)

Networking

Wired** 10/100BASE-T Ethernet (RJ-45 connector)

*a switch is required for surveillance on multiple units.

Note

Caution

All the installation and operations should comply with your local electricity safety rules.

To avoid damage to the unit, never connect more than one type of power supply (PoE IEEE802.3

Ethernet Class 0, DC 12V / AC 24V or AC24V power plug) at the same time. If using PoE, this unit must be connecting only to PoE networks without routing to heterogeneous devices.

1.2.2 Default IP address

Since this is a network-based unit, an IP address must be assigned at the very first. The unit’s default IP address is

192.168.1.30 and sub mask is 255.255.255.0. However, if you have a DHCP server in your network, the unit would obtain an IP address automatically from the DHCP server so that you don’t need to change the camera’s IP address. But be sure to enable DHCP in "Network Settings".

1.2.3 Connecting from a computer & Viewing Preparation

Connecting from a computer

1. Make sure the unit and your computer are in the same subnet.

2. Check whether if the networking available between the unit and the computer by executing ping the default

IP address. To do this, simply start a command prompt (Windows: from the Start Menu, select Program.

Then select Accessories and choose Command Prompt.), and type “Ping 192.168.1.30”. If the message

“Reply from…” appears, it means the connection is available.

3. Start Internet Explorer and enter IP address: 192.168.1.30. A login window should pop up. In the window,

enter the default user name: admin and password: 1234 to log in.

Further administration on the unit can be found in “2. Administration and Configuration".

5

Figure 1 - 3: Login Window

Viewing Preparation

Images of the unit can be viewed through Microsoft Internet Explorer 8 or above. Before viewing, follow these steps to enable the display.

1. Enable Cookies as instructions below

 In Internet Explorer, click Internet Options on the Tools menu.

 On the Privacy tab, move the settings slider to Low or Accept All Cookies.

 Click OK.

2. When a proxy server is used, click Internet Options on the Tools menus of Internet Explorer, select Connect

tab, click LAN button, and set proxy server.

3. Change Security in Internet options as instructions below

 On tool menu, click Internet Option.

 Press the Security tab.

 If the camera operates inside of the intranet, click the Intranet icon.

 If the camera operates outside of the intranet, click the Internet icon.

 Click Custom Level. This will open the Security Settings – Internet Zone screen.

Figure 1 - 4: Security Settings 1/4

6

 Scroll down to the ActiveX controls and plug-ins radio buttons and set as follows:

【

Download signed ActiveX controls】 Prompt (recommended)

【

Download unsigned ActiveX controls】 Prompt

【

Initialize and script ActiveX not marked as safe for scripting】 Prompt

Figure 1 - 5: Security Settings 2/4

【

Automatic prompting for ActiveX controls】Enable

Figure 1 - 6: Security Settings 3/4

7

【

Run ActiveX controls and plug-ins】 Enable

【

Script ActiveX controls marked safe for scripting*】Enable

Figure 1 - 7: Security Settings 4/4

 Press OK to save the settings.

 Close all Microsoft Internet Explorer Windows and restart a new window. This will allow the new settings taking effect.

 Type your setting IP address into the browser.

 Then you should be able to see the camera image screen.

8

1.3

IP Finder

IP Finder is a utility program that helps users locate the unit in the local area network which the computer is connected to.

Please note that IP Finder works only on Microsoft Windows XP, Microsoft Windows Vista, and Microsoft Windows 7. Steps to get the utility program running are listed below.

1. Download IP Finder from MESSOA Website to the computer.

2. Double click on IPFinder.exe in the IP Finder folder, and the IP Finder window should pop out.

3 The window would list information of units in operation at present. Press FIND CAMERA to find more units.

4. Locate and double-click one of the cameras in the list you want to configure the network settings. If you have multiple

cameras connected to your local network, locate the MAC address on the camera to distinguish the target camera from

others.

5. Configure the following settings as needed.

• NAME: Enter a descriptive name for the camera.

• NETWORK SETTINGS: If you have a DHCP server on your network to assign IP addresses to network devices, enable the

DHCP option. Otherwise, manually enter the IP ADDRESS, NET MASK and GATEWAY values.

• USERNAME & PASSWORD: Manually setup preferred username and password.

• SET: Whenever you make revision of camera settings, click “SET” to take effect.

• SW DEFAULT: To perform the factory defaults excluding network settings of the selected camera.

• HW DEFAULT: To perform the factory defaults of the selected camera.

• RESET: To reboot the selected camera.

Click Save to enable the settings and click Exit to exit the utility.

Figure 1 - 8: IP Camera Finder

9

2 Administration and Configuration

2.1

Live View

Figure 2 - 1: First Login Page

After accessing and login to the IP address of the unit, the screen will be shown as the above screenshot. There are 2 main options on the upper left side: “Live View” and “Configuration”. While the upper right side indicates your current login user level with “Logout” option which enables you to log out after pressing. We mainly focus on “Live View” functionalities in this chapter and will detail “Configuration” in the “2.2 Configuration” later.

Figure 2 - 2: Live View

After clicking “Live View”, you will be led to real-time live view screen, the left dropdown menu is for user interface language changing and the “Stream” lets users toggle among each stream settings for better adaptation in different network condition, for which you may refer to “Edit Profiles & Streams” for more details.

The following icons within the table, which are on the top of live view screen, are for some functions activating and alarm warning status. Please refer to the detailed definitions below for more understanding (Flat Mini Dome Series have some differences with other network cameras).

10

Icon Definition

The “Snapshot” button is for taking a snapshot saved in a user-preferred file path.

The “Fixed” button is for users to display a fixed size live view screen.

The “Real” button is for users to display a real size streaming live view screen.

The “Full Screen” button is for users to display a full screen live view display. (Press Esc to back)

The “Audio Input” button is for users to toggle on/off the audio input function.

(1M Flat Mini Dome Network Camera Excluding)

The “Audio Output” button is for users to toggle on/off the audio output function.

(1M Flat Mini Dome Network Camera Excluding)

The vibration-like icon indicates motion(s) being detected in camera coverage.

The siren-like icon indicates that alarm input event is triggered.

(1M/3M Flat Mini Dome Network Camera Excluding)

Table 2 - 1: Live View Icon Definition

Figure 2 - 3: Live View Right-Clicking Controls

Right clicking on the live view screen can pop up more functions to select.

● Version

Click to view the version details.

● Full screen

Click to display a full screen live view display. (Press Esc to back)

● Start Record

Click to record the live view into video file at a preferred file path.

Note

Keep the zoom level of IE as 100% to display normal live view.

11

2.1.1 Model Reference Table

Below table tells the model differences that can be seen on the home page. “√” indicates functions which can be found on the model. “A-F” each indicates a model type, “a-d” indicates different lens as shown below:

A. 1MP/3MP/5MP Indoor Dome Network Camera

B. 3MP/5MP Outdoor IR Dome Network Camera

C. 3MP/5MP Fixed Network Camera

D. 3MP/5MP IR Bullet Network Camera

E. 1MP Flat Mini Dome Network Camera

F. 3MP Flat Mini Dome Network Camera

(*) a. Manual Focus Lens; b. Motorized Lens; c. CS Mount; d. Fixed Focal Lens

Model

Function

Snapshot

Motion Detection

Alarm I/O

Edge Recording

Audio

Remote Lens

Control

Power

Requirement

Zoom Control

Focus Control

DC 12V

Operating

Temperature

AC 24V

PoE

-10ºC ~ 50ºC

(-14ºF ~ 122ºF)

-40ºC ~ 50ºC

(-40ºF ~ 122ºF)

Defrost -

-

√

√

√

√

-

-

√

√

√

√ a

√

A

-

-

√

√

√

√

√

√

√

√

√

√ b

√

√

√

√

√

-

√

-

-

-

√

√

√ a

√

B

√

√

√

√

-

√

√

√

-

√

√

√ b

√

-

-

√

-

-

√

√

√

C c

√

√

√

√

√

√

-

√

√

-

√

-

-

-

√

√

√ a

√

D

√

-

√

√

-

√

√

√

-

√

√

√ b

√

√

-

-

-

-

-

√

√

E d

-

-

-

√

-

√

-

√

-

-

√

√

√

F d

-

√

-

√

-

12

2.2

Configuration

After clicking the “Configuration” option, the screen will be shown as below with several menu options for users to configure on the left side. We will thoroughly introduce them one by one in the following chapters.

Figure 2 - 4: Configure

2.2.1 Information

Users can view, after clicking “Information”, the detailed information related to the unit including Firmware Version, MAC

Address and Model Name in the middle of the screen.

Figure 2 - 5: Information

2.2.2 Image Parameter

The Image Parameter contains several basic display settings like resolution, codec, FPS, GOP and so on. In addition, it has some extending settings including exposure, color, and white balance for the unit. Also, users can set preferred privacy zone under this menu tree as well.

Codec

● Edit Profiles & Streams:

Basically, this unit offers two choices of video codec for real-time viewing: H.264 or MJPEG. By default, there are up to

6 profiles, which have own respective sub settings including Resolution, Codec, Frame Rate, GOP Length, QoS (DSCP)

Codepoint, Rate Control and Bit Rate, can be chosen. And each profile contains up to 3 streams arrangement depending on your settings: Stream1, Stream2, and Stream3, which can be configured separately to send video signals for simultaneous triple streams with optimized quality and bandwidth based on your network environment. After setting up, please be sure to click “Save” to have the desired settings take effect.

• Current Profile: To choose one of the 6 profiles for implementing, click “Save Profile” after selecting.

• Edit Profile: Select one of 6 profiles for editing the sub options.

• MJPEG: While selecting this codec, you can then select sub menu including Frame Rate & Quality.

• H.264: If choosing this codec, there will be more sub menu for you setting. Frame Rate, GOP Length, QoS (DSCP)

Codepoint, Rate Control, which contains 2 kinds including CBR & VBR, and each has its specific Bit Rate value control.

For more details in terms of sub settings under Codec, please refer to the tables listed below.

13

Figure 2 - 6: Basic Parameter

Item

Video Codec

Resolution

Frame Rate (fps)

GOP (Group Of

Pictures) Length

QoS (DSCP)

Codepoint

Bit Rate Mode

Table 2 - 2: Edit Profile Options

MJPEG

H.264

Option Description

MJPEG: Each video frame is individually compressed as single jpeg image with full-scale contents itself and can be retouched freely with ease. However, due to completeness of each frame, it brings about larger file size and thus easily tends to lose frames under limited network bandwidth.

H.264: The latest best-renowned video compression format, it adopts intelligent technology to record variation in each frame rather than record each full frame. As a result, less network bandwidth it requires and file size is prone to be smaller compared with MJPEG.

5M Model: 5M(2592x1944), 3M(2048×1536) ,

1080P(1920×1080) , SXGA(1280×960) , 720P(1280×720),

SVGA(800×600), VGA(640×480), VGA (640x360),

QVGA(320x240), QVGA (320x180)

5M Model:

5M(2592x1944) is the highest resolution

QVGA (320x180) is the lowest resolution.

3M Models: 3M(2048×1536) , 1080P(1920×1080) ,

SXGA(1280×960) , 720P(1280×720), SVGA(800×600),

VGA(640×480), VGA (640x360), QVGA(320x240), QVGA

(320x180)

1M Model: 720P(1280×720), SVGA(800×600),

VGA(640×480), VGA (640x360), QVGA(320x240), QVGA

(320x180)

3M Models:

3M(2048×1536) is the highest resolution

QVGA (320x180) is the lowest resolution.

1M Model:

720P(1280×720) is the highest resolution

QVGA (320x180) is the lowest resolution.

Note: 5M (2592x1944) can be only selected under H.264 codec mode.

NTSC: 1~30

PAL: 1~25

NTSC: 1~60

PAL: 1~50

0 ~ 63

CBR: Constant Bit Rate

VBR: Variable Bit Rate

The utmost fps settings for 2 systems varies as the following:

NTSC: H.264 single stream: 2592×1944@12fps; H.264/MJPEG single stream:

2048×1536@15fps; H.264/MJPEG single stream: 1920×1080 to 320x180@30fps

PAL: H.264 single stream: 2592×1944@12fps; H.264/MJPEG single stream: 2048×1536@15fps;

H.264/MJPEG single stream: 1920×1080 to 320x180@25fps

Select the GOP length number from NTSC: 1 to 60 / PAL: 1 to 50. Less number means the distance between 2 I-frames is smaller, which needs more network bandwidth with better image. By contrast, larger number consumes less bandwidth but is hard to be recovered. The available length number options of GOP will vary based on frame rate settings.

To classify and manage network traffic and provide quality of service (QoS) on modern IP networks, Differentiated Services Code Point (DSCP) is a computer networking architecture that specifies resources allocation to each device on a priority-based pattern for ideal bandwidth management. The bigger value, the higher priority it will be.

Choose the bit rate control selection based on user requirements. Higher bit rate values will result in better quality with bigger file size and thus consume more network bandwidth.

CBR stands for constant mode with certain fixed rate by user definition, while VBR means variable mode in which users can set a range of upper and lower limits respectively for bit rate control.

14

Resolution

2592x1944

(for 5M Models)

2048×1536

(for 3M/5M Models)

1920x1080

(for 3M/5M Models)

1280×960

(for 3M/5M Models)

1280×720

(for 1M/ 3M/5M Models)

Single stream

Table 2 - 3: Correlations of Resolution/Streams/FPS/Codecs – NTSC

2592x1944 @ 12fps

(H.264)

2048×1536 @ 15fps

(H.264/MJPEG)

1920x1080 @ 30fps

(H.264/MJPEG)

1280x960 @ 30fps

(H.264/MJPEG)

1280x720 @ 30fps

(H.264/MJPEG)

Double stream

2592x1944 @ 12fps, 800x600 @ 12fps

2592x1944 @ 12fps, 640x480 @ 12fps

2592x1944 @ 12fps, 640x360 @ 12fps

2592x1944 @ 12fps, 320x240 @ 12fps

2592x1944 @ 12fps, 320x180 @ 12fps

(H.264, H.264/MJPEG)

2048x1536 @ 15fps, 1280x720 @ 15fps

2048x1536 @ 15fps, 800x600 @ 15fps

2048x1536 @ 15fps, 640x480 @ 15fps

2048x1536 @ 15fps, 640x360 @ 15fps

2048x1536 @ 15fps, 320x240 @ 15fps

2048x1536 @ 15fps, 320x180 @ 15fps

(H.264/MJPEG, H.264/MJPEG)

1920x1080 @ 30fps, 640x480 @ 30fps

1920x1080 @ 30fps, 320x240 @ 30fps

1920x1080 @ 30fps, 352x180 @ 30fps

(H.264/MJPEG, H.264/MJPEG)

1280x960 @ 30fps, 1280x720 @ 30fps

1280x960 @ 30fps, 800x600 @ 30fps

1280x960 @ 30fps, 640x480 @ 30fps

1280x960 @ 30fps, 640x360 @ 30fps

1280x960 @ 30fps, 320x240 @ 30fps

1280x960 @ 30fps, 320x180 @ 30fps

(H.264/MJPEG, H.264/MJPEG)

1280x720 @ 30fps, 1280x720 @ 30fps

1280x720 @ 30fps, 800x600 @ 30fps

1280x720 @ 30fps, 640x480 @ 30fps

1280x720 @ 30fps, 640x360 @ 30fps

1280x720 @ 30fps, 320x240 @ 30fps

1280x720 @ 30fps, 320x180 @ 30fps

(H.264/MJPEG, H.264/MJPEG)

Triple stream

2592x1944 @ 12fps, 800x600 @ 12fps, 640x480 @ 12fps

2592x1944 @ 12fps, 640x480 @ 12fps, 640x480 @ 12fps

2592x1944 @ 12fps, 640x360 @ 12fps, 640x480 @ 12fps

2592x1944 @ 12fps, 320x240 @ 12fps, 640x480 @ 12fps

2592x1944 @ 12fps, 320x180 @ 12fps, 640x480 @ 12fps

(H.264, H.264/MJPEG, MJPEG)

2048x1536 @ 15fps, 1280x720 @ 15fps, 640x480 @ 15fps

2048x1536 @ 15fps, 800x600 @ 15fps, 640x480 @ 15fps

2048x1536 @ 15fps, 640x480 @ 15fps, 640x480 @ 15fps

2048x1536 @ 15fps, 640x360 @ 15fps, 640x480 @ 15fps

2048x1536 @ 15fps, 320x240 @ 15fps, 640x480 @ 15fps

2048x1536 @ 15fps, 320x180 @ 15fps, 640x480 @ 15fps

(H.264/MJPEG, H.264/MJPEG, MJPEG)

1920x1080 @ 30fps, 640x480 @ 30fps, 640x360 @ 10fps

1920x1080 @ 30fps, 320x240 @ 30fps, 640x360 @ 10fps

1920x1080 @ 30fps, 352x180 @ 30fps, 640x360 @ 10fps

(H.264/MJPEG, H.264/MJPEG, MJPEG)

1280x960 @ 30fps, 1280x720 @ 30fps, 640x480 @ 10fps

1280x960 @ 30fps, 800x600 @ 30fps, 640x480 @ 10fps

1280x960 @ 30fps, 640x480 @ 30fps, 640x480 @ 10fps

1280x960 @ 30fps, 640x360 @ 30fps, 640x480 @ 10fps

1280x960 @ 30fps, 320x240 @ 30fps, 640x480 @ 10fps

1280x960 @ 30fps, 320x180 @ 30fps, 640x480 @ 10fps

(H.264/MJPEG, H.264/MJPEG, MJPEG)

1280x720 @ 30fps, 1280x720 @ 30fps, 640x360 @ 10fps

1280x720 @ 30fps, 800x600 @ 30fps, 640x360 @ 10fps

1280x720 @ 30fps, 640x480 @ 30fps, 640x360 @ 10fps

1280x720 @ 30fps, 640x360 @ 30fps, 640x360 @ 10fps

1280x720 @ 30fps, 320x240 @ 30fps, 640x360 @ 10fps

1280x720 @ 30fps, 320x180 @ 30fps, 640x360 @ 10fps

(H.264/MJPEG, H.264/MJPEG, MJPEG)

Resolution

2592x1944

(for 5M Models)

2048×1536

(for 3M/5M Models)

1920x1080

(for 3M/5M Models)

1280×960

(for 3M/5M Models)

1280×720

(for 1M/ 3M/5M Models)

Single stream

2592x1944 @ 12fps

(H.264)

2048×1536 @ 15fps

(H.264/MJPEG)

1920x1080 @ 25fps

(H.264/MJPEG)

1280x960 @ 25fps

(H.264/MJPEG)

1280x720 @ 25fps

(H.264/MJPEG)

Table 2 - 4: Correlations of Resolution/Streams/FPS/Codecs – PAL

Double stream

2592x1944 @ 12fps, 800x600 @ 12fps

2592x1944 @ 12fps, 640x480 @ 12fps

2592x1944 @ 12fps, 640x360 @ 12fps

2592x1944 @ 12fps, 320x240 @ 12fps

2592x1944 @ 12fps, 320x180 @ 12fps

(H.264, H.264/MJPEG)

2048x1536 @ 15fps, 1280x720 @ 15fps

2048x1536 @ 15fps, 800x600 @ 15fps

2048x1536 @ 15fps, 640x480 @ 15fps

2048x1536 @ 15fps, 640x360 @ 15fps

2048x1536 @ 15fps, 320x240 @ 15fps

2048x1536 @ 15fps, 320x180 @ 15fps

(H.264/MJPEG, H.264/MJPEG)

1920x1080 @ 25fps, 640x480 @ 25fps

1920x1080 @ 25fps, 320x240 @ 25fps

1920x1080 @ 25fps, 352x180 @ 25fps

(H.264/MJPEG, H.264/MJPEG)

1280x960 @ 25fps, 1280x720 @ 25fps

1280x960 @ 25fps, 800x600 @ 25fps

1280x960 @ 25fps, 640x480 @ 25fps

1280x960 @ 25fps, 640x360 @ 25fps

1280x960 @ 25fps, 320x240 @ 25fps

1280x960 @ 25fps, 320x180 @ 25fps

(H.264/MJPEG, H.264/MJPEG)

1280x720 @ 25fps, 1280x720 @ 25fps

1280x720 @ 25fps, 800x600 @ 25fps

1280x720 @ 25fps, 640x480 @ 25fps

1280x720 @ 25fps, 640x360 @ 25fps

1280x720 @ 25fps, 320x240 @ 25fps

1280x720 @ 25fps, 320x180 @ 25fps

(H.264/MJPEG, H.264/MJPEG)

Triple stream

2592x1944 @ 12fps, 800x600 @ 12fps, 640x480 @ 12fps

2592x1944 @ 12fps, 640x480 @ 12fps, 640x480 @ 12fps

2592x1944 @ 12fps, 640x360 @ 12fps, 640x480 @ 12fps

2592x1944 @ 12fps, 320x240 @ 12fps, 640x480 @ 12fps

2592x1944 @ 12fps, 320x180 @ 12fps, 640x480 @ 12fps

(H.264, H.264/MJPEG, MJPEG)

2048x1536 @ 15fps, 1280x720 @ 15fps, 640x480 @ 15fps

2048x1536 @ 15fps, 800x600 @ 15fps, 640x480 @ 15fps

2048x1536 @ 15fps, 640x480 @ 15fps, 640x480 @ 15fps

2048x1536 @ 15fps, 640x360 @ 15fps, 640x480 @ 15fps

2048x1536 @ 15fps, 320x240 @ 15fps, 640x480 @ 15fps

2048x1536 @ 15fps, 320x180 @ 15fps, 640x480 @ 15fps

(H.264/MJPEG, H.264/MJPEG, MJPEG)

1920x1080 @ 25fps, 640x480 @ 25fps, 640x360 @ 12.5fps

1920x1080 @ 25fps, 320x240 @ 25fps, 640x360 @ 12.5fps

1920x1080 @ 25fps, 352x180 @ 25fps, 640x360 @ 12.5fps

(H.264/MJPEG, H.264/MJPEG, MJPEG)

1280x960 @ 25fps, 1280x720 @ 25fps, 640x480 @ 12.5fps

1280x960 @ 25fps, 800x600 @ 25fps, 640x480 @ 12.5fps

1280x960 @ 25fps, 640x480 @ 25fps, 640x480 @ 12.5fps

1280x960 @ 25fps, 640x360 @ 25fps, 640x480 @ 12.5fps

1280x960 @ 25fps, 320x240 @ 25fps, 640x480 @ 12.5fps

1280x960 @ 25fps, 320x180 @ 25fps, 640x480 @ 12.5fps

(H.264/MJPEG, H.264/MJPEG, MJPEG)

1280x720 @ 25fps, 1280x720 @ 25fps, 640x360 @ 12.5fps

1280x720 @ 25fps, 800x600 @ 25fps, 640x360 @ 12.5fps

1280x720 @ 25fps, 640x480 @ 25fps, 640x360 @ 12.5fps

1280x720 @ 25fps, 640x360 @ 25fps, 640x360 @ 12.5fps

1280x720 @ 25fps, 320x240 @ 25fps, 640x360 @ 12.5fps

1280x720 @ 25fps, 320x180 @ 25fps, 640x360 @ 12.5fps

(H.264/MJPEG, H.264/MJPEG, MJPEG)

15

Exposure

Figure 2 - 7: Exposure

Exposure Mode

It controls the light intensity of picture. There are 2 modes, Manual Exposure and Auto Exposure for adjustment depending on different conditions. When in Manual mode, Shutter Speed is adjustable.

Advanced Exposure

Advanced exposure section is for users to modify more detailed options related to exposure.

• EV Compensation: It is the exposure compensation telling the unit by setting value from -2.0 to 2.0 with intervals of per 0.5 for scenes to be either darker or brighter. (Unavailable when exposure mode is manual)

• Day & Night: Set DAY/NIGHT function by selecting Auto/Color/BW mode. If selected Color mode, the unit is forced to stay in

DAY (COLOR) mode all day and BW for Black & White (Night) mode.

• Noise Reduction: It is the process of removing noises from a signal and be set from 0-255 to decrease noise on the screen.

• BLC: Set an area for Backlight Compensation. Backlight Compensation is a function that achieves the brightness of a selected area to optimal image level. This function is necessary when an auto iris lens tends to close due to an intense light coming from back of object in the area wished to view so that the area is too dark and difficult to see. In this case, users may set the area corresponding to the portion wished to see. (Unavailable when exposure mode is manual)

• WDR: It is intended to provide clear images even under backlight circumstances where intensity of illumination can vary excessively, namely where there are both very bright and very dark areas simultaneously in the field of view. WDR enables the capture and display of both bright and dark areas in the same frame, in a way that there are details in both areas, i.e. bright areas are not saturated, and dark areas are not too dark.

Note

Settings will be restored to the factory defaults if pressing “Reset to default”.

16

White Balance

To set the white balance values to meet ambience condition for best color rendition with 2 modes:

Figure 2 - 8: White Balance Settings

● Auto

It automatically controls color temperature ranging from 2500°K to 10000°K

● Manual

To manually set preferred gain values including the following:

• R (Red) Gain: It allows users to adjust red color in the image ranging from 0 to 255.

• G (Green) Gain: It allows users to adjust green color in the image ranging from 0 to 255.

• B (Blue) Gain: It allows users to adjust blue color in the image ranging from 0 to 255.

Note

Settings will be restored to the factory defaults if pressing “Reset to default”.

Basic Color

Figure 2 - 9: Basic Settings

● Brightness

Set image brightness from level -255 to 255. The 255 indicates the brightest image.

● Contrast

Set image contrast from level 0 to 255. The 255 provides the highest contrast

● Hue

Set picture hue from level -15 to 15. Selecting 15 provides the deepest hue.

● Saturation

It describes the difference of a color from the gray of the same lightness. Increasing saturation deepens the colors of your images, making reds redder and blues bluer. Users can adjust picture saturation level from 0 to 255. Decreasing saturation brings the image closer to a grayscale (that is, monochrome or black-and-white) image. Selecting 255 provides the highest image saturation.

17

● Sharpness

Increasing the sharpness value will sharpen the edges and small feature of viewing images. If the edges appear too smooth or blurred, increase the sharpness; otherwise, decrease the sharpness. Sharpness value can be set from 0 to 15.

The 15 offers the sharpest image.

● Gamma Correction

Set gamma correction between 1 and 0.45.

● Video Orientation

Set image to be left right reversal, upside down or both by selecting “Mirror”, “Flip” and “Both” individually. Selecting “OFF” will deactivate video orientation function.

Note

Settings will be restored to the factory defaults if pressing “Reset to default”.

Remote Lens Control

(Motorized Lens Model Exclusive)

Figure 2 - 10: Remote Lens Control

● Zoom Control

• Zoom Limit could be set between x3 and x30

• Zoom speed could be selected among High, Medium and Low

• By clicking “Start”, users can zoom in/out the lens continuously for a close-up or a wide view, while clicking “Stop” to end zoom in/out actions.

● Focus Control

• The “Manual Focus Continuous” lets users start Focus Near/Focus Far to adjust the focus for better plainness of image. Click

“Start” to carry out action continuously and “Stop” to end the action.

• The “Manual Focus Stepping” has the fine-tuning ability for focus control. The “Normal Step” for Focus Near/Focus Far enables users to manually control desired focus step by step with one click each time differing from Manual Focus Continuous.

• The “Fine Step”, compared with Normal Step, allows users to exert much slighter manual adjustment on focus control even more subtly.

• Click “Start Focus” after selecting “One-Push AF” to have the lens focus automatically immediately.

• Click “Start Calibration” after selecting “One-Push AF” to have the lens calibrate and focus auto simultaneously at once.

18

Privacy Zone

Privacy Zone enables users to black out a specific portion of the screen for privacy concern. There are up to 8 sets of privacy zones for users to define. After setting up a privacy zone, the live view screen will appear a frame, whose color, size and position can be customized by users’ preference.

Figure 2 - 11: Privacy Zone Setting

To set up a privacy mask, you need first to turn ON one of the eight privacy zones (multiple available) and adjust the privacy mask size by pressing with left click and dragging to outline a desired privacy frame. Also, users can select a desired color

(Black, Grey or White) for privacy zone. Press “Save Mask zone” to make settings take effect. If you intend to delete settings, click “Clean Mask zone” to wipe out privacy zone settings.

Note

It is recommended to set the privacy zone slightly larger than the actual area to ensure that privacy area is not revealed during movement.

19

2.2.3 Network Settings

Network

This section for users to set detailed settings related to wired network condition for the unit.

Figure 2 - 12: Network

● Network Settings

• View current network settings: Click “View” to see your current network related settings.

Figure 2 - 13: Current Network Settings

• Camera Name: Input your preferred camera name here.

• HTTP Port: This protocol allows for TCP protocol quality without having to open specific ports for streaming. Users inside a firewall can utilize this protocol to allow streaming data through. It is recommended to use the default port number 80; however, if it is required to change the port number, please contact your system administrator with options ranging from

1025 to 65535.

• HTTPS Port: More secured than HTTP, HTTPS is based on HTTP with SSL/TLS protocol, therefore increasing the security capabilities of SSL/TLS on standard HTTP communications. By default, it’s recommended to adopt 443 as the initial port number. Nevertheless, please also contact your system administrator for other port number ranging from 1025 to 65535 if required.

● IPv4 Address Configure

To set your IP address with further settings under IPv4 here.

• DHCP: If enabled, the unit will automatically obtain an available dynamic IP address from the DHCP server each time it connects to the LAN.

• IPv4 Address: To manually set an IP address under IPv4.

• Subnet Mask: Please use default address: 255.255.255.0. If subnet mask is not properly configured, the unit may not be able to communicate with other devices.

• Default Gateway: Leave blank as default setting. No Default Gateway address required if not used. Ask your network administrator for further information.

• Primary DNS: Same as the above.

• Secondary DNS: Same as the above.

20

● UPnP

• When UPnP (Universal Plug & Play) is set to “ON”, the unit can be detected automatically by any computer in the LAN to skip the installation of the IP Finder utility.

● OSD

• “Camera Name” and “Date & Time” can be set ON to show on screen separately.

FTP

(1M Flat Mini Dome Network Camera Excluding)

In this page, users can set FTP connection related settings.

Figure 2 - 14: FTP Settings

● Action

Simply click “ON” to activate the FTP function or “OFF” to disable it.

● Login ID

Enter a login ID to be allowed to connect with FTP.

● Password

Enter a password associated with the login ID.

● Max Simultaneous Connection

Determine the number of maximum connections by inputting a number in the Max Simultaneous Connections field.

Please note that it is the maximum of FTP Client connections, not the maximum of IE Window’s connections.

To log on the FTP, simply enter ftp://<Login ID>:<Password>@<ip address> in the location field of Microsoft’s Internet

Explorer and the recordings will be shown up. The default setting is ftp://admin:[email protected]. Refer to the names of file and the folder for date and time of recordings.

Note

Please click “Save” button to save your settings. Users can also click “Reset to Default” to set all the settings back to the factory defaults.

21

RTSP

To enable RTSP, simply enter the Login ID, Password and Port (554 by default) with selecting “ON” in Authentication.

Figure 2 - 15: RTSP Settings

● URL

Input a preferred name for representing each RTSP Stream URL. Please note that there’re 2 transferring types of each stream: Unicast and Multicast, and the URL name for each will be as the example below:

• Unicast: stream1

• Multicast: stream1m

● Multicast Address

The IP address for multicasting ought to be from 224.0.1.1 to 239.255.255.254. The RTSP URLs for RTSP Stream 1, RTSP

Stream 2, and RTSP Stream3 are as following respectively:

• rtsp://(ip address)/(stream 1)

• rtsp://(ip address)/(stream 2)

• rtsp://(ip address)/(stream 3)

For example: rtsp://224.0.1.1/stream1

● Audio Multicast Address

Similar to the above, IP address of audio multicast, responsible for audio transmitting, should be defined from 224.0.1.1 to

239.255.255.254 as well.

Note

Please click “Save” button to save your settings. Users can also click “Reset to Default” to set all the settings back to the factory defaults.

22

SNMP

SNMP (Simple Network Management Protocol) is an Internet standard protocol on top of application layer that restructures the exchange of management information among network-attached nodes, which helps administrators to remotely manage network devices and master network problems with ease.

Figure 2 - 16: SNMP Settings

● SNMP V1

Tick “ON” or “OFF” to enable or disable.

● SNMP V2

Tick “ON” or “OFF” to enable or disable.

● SNMP V3

Tick “ON” or “OFF” to enable or disable. Enter password corresponding to User Name. SNMPv3 provided more security features than SNMP V1/SNMP V2.

● Read/Write Community String

Enter the names of Read Community String and Write Community String.

● Trap

Trap under SNMP allows an agent to notify the management station of significant events by way of an unsolicited SNMP message, the asynchronous notification. Tick “ON” or “OFF” to enable or disable trap function here. Input IP address of Trap

Host.

● Heartbeat

To ensure a network free from delayed message, Heartbeat, this communications protocol sends back a message in a given interval to properly confirm message is alive and in fact with a periodic heartbeat. Tick “ON” or “OFF” to enable or disable heartbeat function here. Input IP address & Interval of Heartbeat Host.

● Download MIB

Click “Download” to get specifics of MIB (Management Information Base). MIBs describe the structure of the management data of a device subsystem; which uses a hierarchical namespace containing object identifiers (OID). Each OID identifies a variable that can be read or set via SNMP.

Note

Please click “Save” button to save your settings. Users can also click “Reset to Default” to set all the settings back to the factory defaults.

23

802.1X

802.1X is an IEEE Standard for Port-based Network Access Control and defines the encapsulation of the Extensible

Authentication Protocol (EAP) over IEEE 802 which is known as EAP over LAN. Simply click “ON” to activate it and further select its related EAP protocol types.

Figure 2 - 17: 802.1X Settings

● EAP-MD5

It is the only IETF Standards Track based EAP method and offers the minimal security.

● EAP-TLS

Transport Layer Security (TLS) is an IETF open standard and is well-supported among wireless vendors. Still, it is considered one of the most secure EAP standards available

● EAP-TTLS

Tunneled Transport Layer Security (TTLS) is an EAP protocol that extends TLS and is widely supported across platforms.

● EAP-PEAP

The Protected Extensible Authentication Protocol (PEAP) was jointly developed by Cisco Systems, Microsoft, and RSA

Security and provides unique security for users.

Note

Please click “Save” button to make your settings take effect.

2.2.4 Account Management

Account Settings

Figure 2 - 18: Account Settings

● Admin:

The unit privileged control can be defined under Admin level right here.

The default settings for system Login ID and Password are:

• Username: admin

• Password: 1234

24

● User:

Other than admin, Guest level can only access to unit under authorization from system administrator. At most 5 users are allowed to view live view. No operation will be granted without authorization. The default user’s login name and password are “user1” (user1~5) and “0000”.

To add/delete/change admin/user settings, please refer to the details below.

• New User: To add a new user, simply click “New User” and then input a desired username with password (reenter for reconfirm). Finally click “Save” to take effect.

• Delete User: Choose one of the users from the list and then click “Delete User” to remove it.

• Change Password: Choose admin or one of the users from the list first, and enter an updated password (reenter for reconfirm). Finally click “Save” to take effect.

Caution

• The login ID and Password is supported within 16 characters with the valid alphanumeric value merely including '0' to '9', 'a' to 'z', 'A' to 'Z', '.','-','+','_'and '@'.

• It is NOT allowed to add or delete Admin Level user, which is only one by default.

Note

Please click “Save” button to save your settings. Users can also click “Reset to default” to set all the settings back to the factory defaults.

2.2.5 Event Settings

Motion Detection

This function is designed to trigger a corresponding action when the unit detects motion(s).

Figure 2 - 19: Motion Detection Settings

● Enable

Set “ON” to activate motion detection function.

● Sensitivity

Choose different 3 levels of detecting sensitivity. “High”: Motion is activated with slight changes in brightness or motion.

“Low”: Motion is activated with big changes in brightness or motion.

● Detect Zone

Adjust the detect zone by pressing with left click and dragging on the live view screen to outline a desired size of detected frame.

● Clean

Click “Clean” to erase detect zone settings.

Note

Please click “Save” button to save your settings. Users can also click “Reset to default” to set all the settings back to the factory defaults.

25

Alarm I/O

(1M/3M Flat Mini Dome Network Camera Excluding)

Connecting an alarm input device with the camera can largely extend warning functions. For example, when an infrared detector connected with the camera detects motion based on heat emission, an alarm message would be displayed on the

Web-Client screen for notification. On the other hand, by connecting with an alarm output device such as siren, the camera will send signal to notify siren and thus make it activated when detecting an alarm either by motion detection or signals from alarm input devices.

● Alarm Input

• Enable: Set Alarm Input as “ON” or “OFF”.

Figure 2 - 20: Alarm Input / Output Settings

• Type: Choose NO for normally open or NC for normally close. NO (Normally Opened): An alarm will be triggered when the external contact closes. NC (Normally Closed): An alarm will be triggered when the external contact opens.

● Alarm Output

• When set to “On”, external devices such as sirens or flashing lights that connected to the alarm output connector will signal for alarm activation. And duration can be defined among 0/5/10 seconds, in which 5 seconds is the default settings. 0 second indicates unlimitedly continuous triggering while 5 and 10 seconds mean there’s a time interval between triggering for respective settings.

Note

Please click “Save” button to save your settings. Users can also click “Reset to default” to set all the settings back to the factory defaults.

Email Notification

Figure 2 - 21: Email Notification

26

● SMTP Recording Condition

Simple Mail Transfer Protocol (SMTP) is an Internet standard for e-mail service across networking. Users can receive Alarm or Motion triggered event via email notification by setting here.

● SMTP Server

• SMTP Server: Input a server name or address.

• Login ID: Input a user name with privilege to access the server.

• Password: Input the password associated with Login ID.

• Sender Mail Address: Enter the mail address of the sender

• Port: Set “25” as default or change to dedicated number.

• Authentication: Select an authentication type as following details:

» No_Auth: No restriction

» SMTP_Plain: PLAIN is the name of a registered SASL authentication mechanism which serves as a parameter to the

AUTH command. The PLAIN authentication mechanism is described in RFC 2595. Plain is the least secure of all the SASL authentication mechanisms since the password is sent unencrypted across the network.

» Login: The Login mechanism is supported by Microsoft's Outlook Express and by some other clients.

» TLS_TTLS: TLS is usually implemented on top of any of the Transport Layer protocols encapsulating the applicationspecific protocols such as HTTP, FTP, SMTP, NNTP and XMPP. The TLS protocol allows client-server applications to communicate across a network in a way designed to prevent eavesdropping and tampering. TLS can also be used to tunnel an entire network stack to create a VPN as is the case with OpenVPN.

● Email Notification Triggered

Either Motion detection or Alarm input is enabled; users can edit the related sending mail settings below:

• Subject: To preset a subject of sending email.

• Message: To preset message contents of sending email.

• Attach Image: Select “On” to enable attach the detected image to the sending email.

● E-mail Address List:

This function is designed to notify multiple users via email when alarm in or motion detection functions are set.

• Tick “Enable” and input the assigned email address accordingly.

• Address: Input an email address to which alarm and motion events will be sent. There’re maximum 10 email addresses can be defined here.

• Select either detection (Alarm, Motion) or both for sending email.

Note

Please click “Save” button to save your settings. Users can also click “Reset to default” to set all the settings back to the factory defaults.

27

2.2.6 Record Settings

FTP Recording

Users can save image files via FTP server by setting FTP recording condition beforehand.

Figure 2 - 22: FTP Recording

● FTP Recording Conditions

You can store the image files by either mode including scheduled recording, alarm input triggered recording or motion detection triggered recording.

● FTP Server

FTP (File Transfer Protocol) is used as a service component to transfer files by simply entering the FTP IP address or hostname with the Login ID and password.

• FTP Sever: Input a FTP server name.

• Login ID: Input a user name with privilege to access the server.

• Password: Input the password associated with Login ID.

• Port: Set “21” as default or change to dedicated number.

● Scheduled Recording to FTP

Determine the scheduled recording condition: OFF, All Day, Schedule 1, or Schedule 2 during 24/7.

Figure 2 - 23: Scheduled Recording to FTP Settings

• Recording cycle: Set a time interval from 5 to 120 seconds for recording images.

• File Name Prefix: Set a prefixed name for recording file.

• Server Path: Set the desired path where the data is to be stored on the server.

● Alarm/Motion Event Recording to FTP

These functions are to define the way to record video once a motion/alarm event is detected by the unit (1M/3M Flat Mini

Dome Network Camera do not support alarm event recording).

28

Figure 2 - 24: Alarm/Motion Event Recording to FTP Settings

• Pre Recording Frame: Set the number of frame to be recorded immediately before an event occurs.

• Pre Recording Cycle: Set a time interval before recording.

• Recording Frame: Set the number of frame while recording.

• Recording Cycle: Set a time interval for recording.

• File Name: Set file name to be stored for motion/alarm events separately.

• Sever Path: Set the desired path on the server to store data for motion/alarm events.

Note

Please click “Save” button to save your settings. Users can also click “Reset to default” to set all the settings back to the factory defaults.

Edge Recording

(1M Flat Mini Dome Network Camera Excluding)

Image files can be saved onto the SD card through well setting in this section. Please make sure to insert SD card prior to enabling this function.

Figure 2 - 25: Edge Recording

● Edge Recording Conditions

Choose one of the conditions to enable the SD card recording: Alarm, Motion, or Network Lose.

● System Information

• Alarm/Motion Recording Time: Set a time interval for SD card recording of alarm or motion event triggered.

• Auto Overwrite: Set “OFF” or “ON” to disable or enable overwriting SD card automatically when SD card is full of recording files.

● SD Card Information

• Usage: Information of memory card usage.

• SD Format: To execute memory card format process.

29

2.2.7 System Settings

Date & Time

Figure 2 - 26: Date & Time

● Current Server Time

The server current date/time is displayed here.

● Synchronization Mode

There’re 3 modes for users to set date/time.

• Manual: Select it to manually set your date/time.

• Synchronize with PC Date: Select it to simply synchronize date/time with computer.

• Synchronize with NTP Server: Select it to synchronize date/time with the assigned NTP server.

● NTP

Set up your NTP related settings here if NTP Server enabled.

• NTP Server: Please input desired NTP server in the field.

• Synchronizing Period: Select sync period between 1 and 24 by 6 of each interval.

• NTP Test: Click it to test if your assigned NTP server is workable.

● Time Zone

Choose one of the time zones based on your located country/area

Note

Please click “Save” button to save your settings. Users can also click “Reset to default” to set all the settings back to the factory defaults.

30

Audio

(1M Flat Mini Dome Network Camera Excluding)

Figure 2 - 27: Audio Settings

● Type

Two audio codecs G711-Alaw/G711-Ulaw can be chosen from. (Audio Input only)

● Enable

Set "ON" to activate audio input/output when audio input/output devices are plugged.

● Level

The sound levels are selectable for audio input/output: Low/Mid/High for audio input/output.

Note

Please click “Save” button to save your settings. Users can also click “Reset to default” to set all the settings back to the factory defaults.

Firmware Update

Users can manually update System Firmware if available. All unit motions will be stopped during firmware update. Please close any other screens before firmware update. Never disconnect power or LAN cable during the updating process. It takes approximately 3 minutes for the unit to reboot after firmware update process. Please reboot the computer as well after firmware updated. Again, power can’t be lost when updating firmware since it will cause the update failure and manufacturer maintenance will be required.

Figure 2 - 28: Firmware Update

● Click Browse to choose a corresponding firmware version and click Upload to proceed.

31

Initialize

Figure 2 - 29: Initialize Settings

● Video Type

Select “NTSC” or “PAL” as required. Flickering by fluorescent light can be reduced by selecting “PAL” for the power frequency

50Hz, “NTSC” for the power frequency 60Hz

● Import User Configuration

Press “Browse” to select the file and then click “Import” to upload configuration settings from local to the unit.

● Export User Configuration

Press “Export” to download configuration settings to local computer.

● Reboot Camera

Press “Reboot Camera” to reboot the unit.

● Software Factory Default

Press it to reset all configuration settings back to factory defaults excluding network settings.

● Remote Hardware Factory Default

Press it to reset all configuration settings back to factory defaults.

2.2.8 Event Log

Figure 2 - 30: System Log

● Click “Download Log” to save the log file of unit to your local computer.

32

Appendix A: Specifications of Indoor Dome Network

Camera (Manual Focus Model)

Video

Model Type

Sensor Type

Active Pixels

Compression

Streaming

1M Manual Focus Model 3M Manual Focus Model

1/4" progressive scan CMOS sensor

1280 x 800 (HxV)

H.264 / MJPEG

Triple simultaneous streams with multiple video profile

1/3" progressive scan CMOS sensor

2304 x 1536 (HxV)

Resolution

Max. Frame Rate

Day/Night

Day/Night Mode

Shutter Time

Minimum Illumination

720P, SVGA(800x 600), VGA(640x480), 640x360,

QVGA(320x240), 320x180

QXGA(2048x1536), 1080P, 1280x960, 720P, 800x600,

VGA(640x480), 640x360, QVGA(320x240), 320x180

HDTV 720p (1280x720) at 30/25fps (NTSC/PAL)

3MP 4:3 (2048x1536) at 15fps;

2MP Full HD 16:9 (1920x1080) at 30/25fps (NTSC/PAL)

Mechanical (ICR) D/N Control

Auto/ BW/ Color

1/10,000s to 1/7.5s Selectable (60Hz);

1/10,000s to 1/6.25s Selectable (50Hz)

Color: 0.1 lux at 50 IRE, 0.02 lux at 10 IRE, F1.4;

B/W: 0.02 lux at 50 IRE, 0.004 lux at 10 IRE, F1.4

(Shutter speed: 1/15 sec)

NTSC: 720x480 @30fps; PAL: 720x576 @25fps

CBR, VBR

Video Output

Bit Rate Control

Lens

Lens Type

Focal Length

Focus / Zoom

View Angle

IRIS Control

Ethernet Detection

Others

Events

Event Actions

Built-in; Varifocal f=2.8~10mm, F1.4

Manual

H: 68°(Wide)~23°(Tele)

DC IRIS

Audio

Audio Communication

Compression

Audio In/Out

Image Enhancement

Two-way Audio

G.711 PCM 8kHz, a/μ-law support

External microphone and speaker

Image Settings

WDR

DNR

Privacy Zone

Image Orientation

AES, AWB, AGC

Exposure Mode: AES / ALC / Flickerless / Manual;

White Balance: Auto / Manual;

Backlight Compensation

Configurable Brightness, Contrast, Hue, Saturation, and Sharpness

Gamma Correction

Enhanced Digital WDR

Configurable 3DNR setting

Yes, up to 8 privacy zones

Mirror, Flip

Frequency Control

Date & Time Stamp

NTSC(60Hz)/ PAL(50Hz)

Yes

Intelligent Video & Event Management

Motion Detection Yes, 3-level sensitivity

Network loss detection

Optimized i-frame (GOP) setting

Motion detection, ethernet detection, external alarm

Event snapshot to remote FTP storage / email recipients;

Edge recording to SD card;

HTTP event query, HTTP event client pulling f=3~9mm, F1.2

H: 78°(Wide)~28°(Tele)

Event snapshot, Edge recording, Manual Snapshot, Manual Recording Store Category

Local Storage

Memory Card Slot

Memory Card Overwrite

SDXC/SDHC card support

Yes

33

Network

Protocol

Ethernet

ONVIF

Browser

Security

ARP, DHCP, DNS, FTP, HTTP, HTTPS, ICMP, IGMP, IPv4, IPv6, NTP, RTSP/RTCP/RTP, QoS, SMTP, SNMP, TCP, UDP,

UPnP, IEEE802.1X

10Base-T/100Base-TX Ethernet connection for LAN / WAN, RJ-45

Yes

Internet Explorer, Chrome, Firefox, Safari

Multiple user access levels with password protection; IP address filtering;

IEEE 802.1X network access control, HTTPS encryption, and digest authentication

I/O & Controls

Power

Power LED Indicator

Alarm In/Out

Network

Audio In/Out

Analog Video

System Reboot

Factory Default

Power

Power Requirement

Power Consumption (Max.)

Mechanical

Dimensions(ΦxH)

Weight

3-Axis

Pan/Tilt Adjustment

Environmental

Operating Temperature

Operating Humidity

Storage Temperature

Regulatory

Approvals

2-pin Terminal block/ Female RJ-45 10BASE-T/100BASE-TX PoE

System power and status indicator

Terminal block 1 in / 1 relay out(30V, 1A)

RJ-45 with LED Indicator

Terminal block 1 in / 1 out

1 x composite video out, micro JST

Reset x 1

Default x 1, pressing 5 sec for loading factory default

DC 12V & AC 24V ± 10% / PoE (IEEE 802.3af, class 0)

6W

Φ125mm x 106mm (Φ4.92" x 4.18")

500g (1.1 lb)

Yes

Pan: 0°-350°, Tilt: 15°-90°, Rotate: 0°-350° (Max.)

-10ºC ~ 50ºC (-14ºF ~ 122ºF)

90% RH, non-condensing

-40°C ~ 60°C (-40°F ~ 140°F)

CE, FCC, RoHS

Note: Product specifications and pictures are subject to change without notice.

6.5W

34

Appendix B: Specifications of Indoor Dome Network

Camera (Motorized Lens Model)

Video

Model Type

Sensor Type

Active Pixels

Compression

Streaming

3M Motorized Lens Model

1/3" progressive scan CMOS sensor

2304 x 1536 (HxV)

H.264 / MJPEG

5M Motorized Lens Model

1/3.2" progressive scan CMOS sensor

2592x1944 (HxV)

Resolution

Max. Frame Rate

Triple simultaneous streams with multiple video profile

QXG A ( 2 0 4 8 x 1 5 3 6 ) , 1 0 8 0 P, 1 2 8 0 x 9 6 0 , 7 2 0 P,

S V G A ( 8 0 0 x 6 0 0 ) , V G A ( 6 4 0 x 4 8 0 ) , 6 4 0 x 3 6 0 ,

QVGA(320x240), 320x180

2592x1944, QXGA(2048x1536), 1080P, 1280x960,

720P, SVGA(800x 600), VGA(640x480), 640x360,

QVGA(320x240), 320x180

3MP 4:3 (2048x1536) at 15fps;

2MP Full HD 16:9 (1920x1080) at 30/25fps (NTSC/PAL)

5MP 4:3 (2592x1944) at 12 fps

3MP 4:3 (2048x1536) at 15 fps

2MP Full HD 16:9 (1920x1080) at 30/25fps (NTSC/PAL)

Mechanical (ICR) D/N Control Day/Night

Day/Night Mode

Shutter Time

Minimum Illumination

Auto/ BW/ Color

1/10,000s to 1/7.5s Selectable (60Hz);

1/10,000s to 1/6.25s Selectable (50Hz)

Color: 0.1 lux at 50 IRE, 0.02 lux at 10 IRE;

B/W: 0.02 lux at 50 IRE, 0.04 lux at 10 IRE;

F1.2, (Shutter speed: 1/15 sec)

NTSC: 720x480 @30fps; PAL: 720x576 @25fps

CBR, VBR

Color: 0.15 lux at 50 IRE, 0.03 lux at 10 IRE,

B/W: 0.03 lux at 50 IRE, 0.006 lux at 10 IRE,

F1.2 (Shutter speed: 1/15 sec)

Video Output

Bit Rate Control

Lens

Lens Type

Focal Length

Focus / Zoom

View Angle

Built-in; Varifocal f=3~9mm, F1.2

Autofocus, motorized / Remote

H: 78°(Wide)~28°(Tele)

DC IRIS

Autofocus, motorized / Remote

IRIS Control

Audio

Audio Communication

Compression

Audio In/Out

Image Enhancement

Two-way Audio

G.711 PCM 8kHz, a/μ-law support

External microphone and speaker

Image Settings

WDR

DNR

Privacy Zone

AES, AWB, AGC

Exposure Mode: AES / ALC / Flickerless / Manual;

White Balance: Auto / Manual;

Backlight Compensation

Configurable Brightness, Contrast, Hue, Saturation, and Sharpness

Gamma Correction

Enhanced Digital WDR

Configurable 3DNR setting

Yes, up to 8 privacy zones

Image Orientation

Frequency Control

Mirror, Flip

NTSC(60Hz)/ PAL(50Hz)

Date & Time Stamp Yes

Intelligent Video & Event Management

Motion Detection

Ethernet Detection

Others

Events

Event Actions

Yes, 3-level sensitivity

Network loss detection

Optimized i-frame (GOP) setting

Motion detection, ethernet detection, external alarm

Event snapshot to remote FTP storage / email recipients;

Edge recording to SD card;

HTTP event query, HTTP event client pulling

Event snapshot, Edge recording, Manual Snapshot, Manual Recording Store Category

Local Storage

Memory Card Slot

Memory Card Overwrite

SDXC/SDHC card support

Yes

35

Network

Protocol

Ethernet

ONVIF

Browser

Security

ARP, DHCP, DNS, FTP, HTTP, HTTPS, ICMP, IGMP, IPv4, IPv6, NTP, RTSP/RTCP/RTP, QoS, SMTP, SNMP, TCP, UDP,

UPnP, IEEE802.1X

10Base-T/100Base-TX Ethernet connection for LAN / WAN, RJ-45

Yes

Internet Explorer, Chrome, Firefox, Safari

Multiple user access levels with password protection; IP address filtering;

IEEE 802.1X network access control, HTTPS encryption, and digest authentication

I/O & Controls

Power

Power LED Indicator

Alarm In/Out

Network

Audio In/Out

Analog Video

System Reboot

Factory Default

Power

Power Requirement

Power Consumption (Max.)

Mechanical

Dimensions(ΦxH)

Weight

3-Axis

Pan/Tilt Adjustment

Environmental

Operating Temperature

Operating Humidity

Storage Temperature

Regulatory

Approvals

2-pin Terminal block/ Female RJ-45 10BASE-T/100BASE-TX PoE

System power and status indicator

Terminal block 1 in / 1 relay out(30V, 1A)

RJ-45 with LED Indicator

Terminal block 1 in / 1 out

1 x composite video out, micro JST

Reset x 1

Default x 1, pressing 5 sec for loading factory default

DC 12V & AC 24V ± 10% / PoE (IEEE 802.3af, class 0)

7W

Φ125mm x 106mm (Φ4.92" x 4.18")

500g (1.1 lb)

Yes

Pan: 0°-350°, Tilt: 15°-90°, Rotate: 0°-350° (Max.)

-10ºC ~ 50ºC (-14ºF ~ 122ºF)

90% RH, non-condensing

-40°C ~ 60°C (-40°F ~ 140°F)

CE, FCC, RoHS

Note: Product specifications and pictures are subject to change without notice.

36

Appendix C: Specifications of Outdoor IR Dome Network

Camera

Video

Model Type

Sensor Type

Active Pixels

Compression

Streaming

Resolution

Max. Frame Rate

Day/Night

Day/Night Mode

Shutter Time

Minimum Illumination

Video Output

Bit Rate Control

Lens

Lens Type

Focal Length

Focus / Zoom

View Angle

IRIS Control

IR LEDs

LED Quantity

IR Distance

IR Turn on Status

LED Life

3M Manual Focus Model

1/3" progressive scan CMOS sensor

3M Motorized Lens Model 5M Motorized Lens Model

1/3.2" progressive scan CMOS sensor

2592x1944 (HxV) 2304 x 1536 (HxV)

H.264 / MJPEG

Triple simultaneous streams with multiple video profile

QXGA(2048x1536), 1080P, 1280x960, 720P, SVGA(800x600), VGA(640x480),

640x360, QVGA(320x240), 320x180

3MP 4:3 (2048x1536) at 15fps;

2MP Full HD 16:9 (1920x1080) at 30/25fps (NTSC/PAL)

2592x1944, QXGA(2048x1536),

1080P, 1280x960, 720P, SVGA(800x

600), VGA(640x480), 640x360,

QVGA(320x240), 320x180

5MP 4:3 (2592x1944) at 12 fps

3MP 4:3 (2048x1536) at 15 fps

2MP Full HD 16:9 (1920x1080) at

30/25fps (NTSC/PAL)

Mechanical (ICR) D/N Control

Auto/ BW/ Color

1/10,000s to 1/7.5s Selectable (60Hz);

1/10,000s to 1/6.25s Selectable (50Hz)

IR LED OFF:

Color: 0.1 lux at 50 IRE, 0.02 lux at 10 IRE;

F1.2 (Shutter speed: 1/15 sec)

IR LED ON: 0 lux

IR LED OFF:

Color: 0.15 lux at 50 IRE,

0.03 lux at 10 IRE;

F1.2(Shutter speed: 1/15 sec)

IR LED ON: 0 lux

NTSC: 720x480 @30fps; PAL: 720x576 @25fps

CBR, VBR

Built-in; Varifocal f=3~9mm, F1.2

Manual

H: 78°(Wide)~28°(Tele)

DC IRIS

Auto Focus / Motorized remote focus control

20 pcs(850nm)

20 meters (65ft)

Under 5 lux by auto control

More than 10,000 hours

25 meters (82ft)

Audio

Audio Communication

Compression

Audio In/Out

Image Enhancement

Two-way Audio

G.711 PCM 8kHz, a/μ-law support

External microphone and speaker

Image Settings

WDR

DNR

Privacy Zone

Image Orientation

AES, AWB, AGC

Exposure Mode: AES / ALC / Flickerless / Manual;

White Balance: Auto / Manual;

Backlight Compensation

Configurable Brightness, Contrast, Hue, Saturation, and Sharpness

Gamma Correction

Enhanced Digital WDR

Configurable 3DNR setting

Yes, up to 8 privacy zones

Mirror, Flip

Frequency Control

Date & Time Stamp

NTSC(60Hz)/ PAL(50Hz)

Yes

Intelligent Video & Event Management

Motion Detection Yes, 3-level sensitivity

Ethernet Detection Network loss detection

37

Others

Events

Event Actions

Optimized i-frame (GOP) setting

Motion detection, ethernet detection, external alarm

Event snapshot to remote FTP storage / email recipients;

Edge recording to SD card;

HTTP event query, HTTP event client pulling

Event snapshot, Edge recording, Manual Snapshot, Manual Recording Store Category

Local Storage

Memory Card Slot

Memory Card Overwrite

Network microSDXC/SDHC card support

Yes

Protocol

Ethernet

ONVIF

Browser

Security

ARP, DHCP, DNS, FTP, HTTP, HTTPS, ICMP, IGMP, IPv4, IPv6, NTP, RTSP/RTCP/RTP, QoS, SMTP, SNMP, TCP, UDP,

UPnP, IEEE802.1X

10Base-T/100Base-TX Ethernet connection for LAN / WAN, RJ-45

Yes

Internet Explorer, Chrome, Firefox, Safari

Multiple user access levels with password protection; IP address filtering;

IEEE 802.1X network access control, HTTPS encryption, and digest authentication

I/O & Controls

Power

Power LED Indicator

Alarm In/Out

Network

Audio In/Out

Analog Video

System Reboot

Factory Default

Power

2-pin Terminal block/ Female RJ-45 10BASE-T/100BASE-TX PoE

System power and status indicator

Terminal block 1 in / 1 relay out(30V, 1A)

RJ-45 with LED Indicator

Terminal block 1 in / 1 out

1 x composite video out, micro JST

Reset x 1

Default x 1, pressing 5 sec for loading factory default

Power Requirement

Power Consumption (Max.)

Mechanical

Dimensions(ΦxH)

Weight

3-Axis

Pan/Tilt Adjustment

Protection

IK10 Compliant

Operating Temperature

Operating Humidity

Storage Temperature

Regulatory

Approvals

Heater Drive: AC 24V ± 10% / PoE (IEEE 802.3af)

*Arctic power-on support by PoE at -50°C

Defrost Drive: AC 24V ± 10%

26W

Φ147mm x 140mm (Φ5.79" x 5.5")

1250g (2.76 lb)

Yes

Pan: 0°-350°, Tilt: 15°-90°, Rotate: 0°-350° (Max.)

IP66 Certified, IP67/IP68 Compliant, IK10 Compliant

-50ºC ~ 50ºC (-58ºF ~ 122ºF)

90% RH, non-condensing

-20°C ~ 60°C (-4°F ~ 140°F)

CE, FCC, RoHS

Note: Product specifications and pictures are subject to change without notice.

38

Appendix D: Specifications of Fixed Network Camera

Video

Model Type

Sensor Type

Active Pixels

Compression

Streaming

Resolution

Max. Frame Rate

3M Fixed Network Camera 5M Fixed Network Camera

1/3" progressive scan CMOS sensor

2304 x 1536 (HxV)

H.264 / MJPEG

Triple simultaneous streams with multiple video profile

1/3.2" progressive scan CMOS sensor

2592x1944 (HxV)

QXG A ( 2 0 4 8 x 1 5 3 6 ) , 1 0 8 0 P, 1 2 8 0 x 9 6 0 , 7 2 0 P,

S V G A ( 8 0 0 x 6 0 0 ) , V G A ( 6 4 0 x 4 8 0 ) , 6 4 0 x 3 6 0 ,

QVGA(320x240), 320x180

2592x1944, QXGA(2048x1536), 1080P, 1280x960,

720P, SVGA(800x 600), VGA(640x480), 640x360,

QVGA(320x240), 320x180

3MP 4:3 (2048x1536) at 15fps;

2MP Full HD 16:9 (1920x1080) at 30/25fps (NTSC/PAL)

5MP 4:3 (2592x1944) at 12 fps

3MP 4:3 (2048x1536) at 15 fps

2MP Full HD 16:9 (1920x1080) at 30/25fps (NTSC/PAL)

Mechanical (ICR) D/N Control Day/Night

Day/Night Mode

Shutter Time

Minimum Illumination

Auto/ BW/ Color

1/10,000s to 1/7.5s Selectable (60Hz);

1/10,000s to 1/6.25s Selectable (50Hz)

Color: 0.1 lux at 50 IRE, 0.02 lux at 10 IRE;

B/W: 0.02 lux at 50 IRE, 0.04 lux at 10 IRE;

F1.2, (Shutter speed: 1/15 sec)

NTSC: 720x480 @30fps; PAL: 720x576 @25fps

CBR, VBR

Color: 0.15 lux at 50 IRE, 0.03 lux at 10 IRE,

B/W: 0.03 lux at 50 IRE, 0.006 lux at 10 IRE,

F1.2 (Shutter speed: 1/15 sec)

Video Output

Bit Rate Control

Lens

IRIS Control

Lens Mount

Audio

Audio Communication

Compression

Audio In/Out

Image Enhancement

DC IRIS

CS Mount; External back-focus adjustment

Two-way Audio

G.711 PCM 8kHz, a/μ-law support

External microphone and speaker

Image Settings

WDR

DNR

Privacy Zone

Image Orientation

Frequency Control

Date & Time Stamp

AES, AWB, AGC

Exposure Mode: AES / ALC / Flickerless / Manual;

White Balance: Auto / Manual;

Backlight Compensation

Configurable Brightness, Contrast, Hue, Saturation, and Sharpness

Gamma Correction

Enhanced Digital WDR

Configurable 3DNR setting

Yes, up to 8 privacy zones

Mirror, Flip

NTSC(60Hz)/ PAL(50Hz)

Yes

Intelligent Video & Event Management

Motion Detection Yes, 3-level sensitivity

Ethernet Detection

Others

Events

Network loss detection

Optimized i-frame (GOP) setting

Motion detection, ethernet detection, external alarm

Event Actions

Event snapshot to remote FTP storage / email recipients;

Edge recording to SD card;

HTTP event query, HTTP event client pulling

Event snapshot, Edge recording, Manual Snapshot, Manual Recording Store Category

Local Storage

Memory Card Slot

Memory Card Overwrite

Network

SDXC/SDHC card support

Yes

Protocol

Ethernet

ONVIF

Browser

ARP, DHCP, DNS, FTP, HTTP, HTTPS, ICMP, IGMP, IPv4, IPv6, NTP, RTSP/RTCP/RTP, QoS, SMTP, SNMP, TCP, UDP,

UPnP, IEEE802.1X

10Base-T/100Base-TX Ethernet connection for LAN / WAN, RJ-45

ONVIF

Internet Explorer, Chrome, Firefox, Safari

39

Security

Multiple user access levels with password protection; IP address filtering;

IEEE 802.1X network access control, HTTPS encryption, and digest authentication

I/O & Controls

Power

Power LED Indicator

Alarm In/Out

Network

Audio In/Out

Analog Video

System Reboot

Factory Default

Power

Power Requirement

Power Consumption (Max.)

Mechanical

Dimensions(WxDxH)

Weight

Environmental

Operating Temperature

Operating Humidity

Storage Temperature

Regulatory

Approvals

3-pin spring terminal/ Female RJ-45 10BASE-T/ 100BASE-TX PoE

System power and status indicator

Terminal block 1 in / 1 relay out(30V, 1A)

RJ-45 with LED Indicator

Terminal block 1 in / 1 out

BNC X1, 1.0Vp-p, 75Ω

Reset x 1

Default x 1, pressing 5 sec for loading factory default

DC 12V & AC 24V ± 10% / PoE (IEEE 802.3af, class 0)

6W

125 x 69 x 56 mm (4.9" x 2.7" x 2.2")

400g (0.88 lb) w/o lens

-10ºC ~ 50ºC (-14ºF ~ 122ºF)

90% RH, non-condensing

-40°C ~ 60°C (-40°F ~ 140°F)

CE, FCC, RoHS

Note: Product specifications and pictures are subject to change without notice.

40

Appendix E: Specifications of IR Bullet Network Camera

Video

Model Type

Sensor Type

Active Pixels

Compression

Streaming

Resolution

Max. Frame Rate

Day/Night

Day/Night Mode

Shutter Time

Minimum Illumination

3M Motorized Lens Model 5M Motorized Lens Model

1/3" progressive scan CMOS sensor

2304 x 1536 (HxV)

H.264 / MJPEG

Triple simultaneous streams with multiple video profile

1/3.2" progressive scan CMOS sensor

2592x1944 (HxV)

QXG A ( 2 0 4 8 x 1 5 3 6 ) , 1 0 8 0 P, 1 2 8 0 x 9 6 0 , 7 2 0 P,

S V G A ( 8 0 0 x 6 0 0 ) , V G A ( 6 4 0 x 4 8 0 ) , 6 4 0 x 3 6 0 ,

QVGA(320x240), 320x180

2592x1944, QXGA(2048x1536), 1080P, 1280x960,

720P, SVGA(800x 600), VGA(640x480), 640x360,

QVGA(320x240), 320x180

3MP 4:3 (2048x1536) at 15fps;

2MP Full HD 16:9 (1920x1080) at 30/25fps (NTSC/PAL)

5MP 4:3 (2592x1944) at 12 fps

3MP 4:3 (2048x1536) at 15 fps

2MP Full HD 16:9 (1920x1080) at 30/25fps (NTSC/PAL)

Mechanical (ICR) D/N Control

Auto/ BW/ Color

1/10,000s to 1/7.5s Selectable (60Hz);

1/10,000s to 1/6.25s Selectable (50Hz)

IR LED OFF:

Color: 0.1 lux at 50 IRE, 0.02 lux at 10 IRE,

F1.2; (Shutter speed: 1/15 sec)

IR LED ON: 0 Lux

NTSC: 720x480 @30fps; PAL: 720x576 @25fps

CBR, VBR

IR LED OFF:

Color: 0.15 lux at 50 IRE, 0,03 lux at 10 IRE,

F1.2; (Shutter speed: 1/15 sec)

IR LED ON: 0 lux

Video Output

Bit Rate Control

Lens

Lens Type

Focal Length

Focus / Zoom

View Angle

IRIS Control

IR LEDs

LED Quantity

IR Distance

IR Turn on Status

LED Life

Audio

Audio Communication

Compression

Audio In/Out

Image Enhancement

Built-in; Varifocal f=3~9mm, F1.2

Autofocus, motorized / Remote

H: 78°(Wide)~28°(Tele)

DC IRIS

48 pcs (850nm)

30 meters (98ft)

Under 5 lux by auto control

More than 10,000 hours

Two-way Audio

G.711 PCM 8kHz, a/μ-law support

External microphone and speaker

Image Settings

WDR

DNR

Privacy Zone

Image Orientation

Frequency Control

AES, AWB, AGC

Exposure Mode: AES / ALC / Flickerless / Manual;

White Balance: Auto / Manual;

Backlight Compensation

Configurable Brightness, Contrast, Hue, Saturation, and Sharpness

Gamma Correction

Enhanced Digital WDR

Configurable 3DNR setting

Yes, up to 8 privacy zones

Mirror, Flip

NTSC(60Hz)/ PAL(50Hz)

Date & Time Stamp Yes

Intelligent Video & Event Management

Motion Detection

Ethernet Detection

Yes, 3-level sensitivity

Network loss detection

Others

Events

Event Actions

Store Category

Optimized i-frame (GOP) setting

Motion detection, audio detection, ethernet detection, external alarm

Event snapshot to remote FTP storage/ email recipients, Edge recording to SD card,

HTTP event query, HTTP event client pulling

Event snapshot, Edge recording, Manual Snapshot, Manual Recording

41

Local Storage

Memory Card Slot

Memory Card Overwrite

Network microSDXC/SDHC card support

Yes

Protocol

Ethernet

ONVIF

Browser

Security

ARP, DHCP, DNS, FTP, HTTP, HTTPS, ICMP, IGMP, IPv4, IPv6, NTP, RTSP/RTCP/RTP, QoS, SMTP, SNMP, TCP, UDP,

UPnP, IEEE802.1X

10Base-T/100Base-TX Ethernet connection for LAN / WAN, RJ-45

Yes

Internet Explorer, Chrome, Firefox, Safari

Multiple user access levels with password protection; IP address filtering;

IEEE 802.1X network access control, HTTPS encryption, and digest authentication

I/O & Controls

Power

Power LED Indicator

Alarm In/Out

Network

Audio In/Out

Analog Video

System Reboot

Factory Default

Power

All-in-one tail cable out, 2-pin Terminal block/ Female RJ-45 10BASE-T/100BASE-TX PoE

System power and status indicator

Terminal block 1 in / 1 relay out(30V, 1A)

RJ-45 with LED Indicator

Terminal block 1 in / 1 out

1 x composite video out, micro JST

Reset x 1

Default x 1, pressing 5 sec for loading factory default

Power Requirement

Power Consumption (Max.)

Mechanical

Dimensions(WxDxH)

Weight

Protection

Environmental

Operating Temperature

Operating Humidity

Storage Temperature

Regulatory

Approvals

AC 24V ± 10% / PoE (IEEE 802.3af)

*Arctic power-on support by PoE at -40°C

11.5W

115 x 264 x 110 mm (4.53” x 10.39” x 4.33”)

1600g (3.44 lb)

IP67 Certified, IP68 Compliant, IK10 Compliant

(On-board heating device) -40ºC ~ 50ºC (-40ºF ~ 122 ºF)

90% RH, non-condensing

-20ºC ~ 60ºC (-4ºF ~ 140ºF)

CE, FCC, RoHS

Note: Product specifications and pictures are subject to change without notice.

42

Appendix F: Specifications of Flat Mini Dome Network

Camera

Video

Model Type

Sensor Type

Active Pixels

Compression

Streaming

1M Fixed Lens Model 3M Fixed Lens Model

1/4" progressive scan CMOS sensor

1280 x 800 (HxV)

H.264 / MJPEG

Triple simultaneous streams with multiple video profile

1/3" progressive scan CMOS sensor

2304 x 1536 (HxV)

Resolution

Max. Frame Rate

Day/Night

Day/Night Mode

Shutter Time

Minimum Illumination

720P, SVGA(800x 600), VGA(640x480), 640x360,

QVGA(320x240), 320x180

QXGA(2048x1536), 1080P, 1280x960, 720P, SVGA(800x

600), VGA(640x480), 640x360, QVGA(320x240),

320x180

HDTV 720p (1280x720) at 30/25 fps (NTSC/PAL)

3MP 4:3 (2048x1536) at 15 fps

2MP Full HD 16:9 (1920x1080) at 30/25 fps (NTSC/PAL)

Mechanical (ICR) D/N Control

Auto/ BW/ Color

1/10,000s to 1/7.5s Selectable (60Hz); 1/10,000s to 1/6.25s Selectable (50Hz)

Color: 0.3 lux at 50 IRE, 0.06 lux at 10 IRE,

B/W: 0.2 lux at 50 IRE, 0.04 lux at 10 IRE,

F1.8 (Shutter speed: 1/15 sec)

Color: 0.4 lux at 50 IRE,0.08 lux at 10 IRE,

B/W: 0.3 lux at 50 IRE, 0.07 lux at 10 IRE,

F1.8 (Shutter speed: 1/35 sec)

NTSC: 720x480 @30fps; PAL: 720x576 @25fps

CBR, VBR

Video Output

Bit Rate Control

Lens

Lens Type

Focal Length

View Angle

Audio

Audio Communication

Compression

Audio In/Out

Ethernet Detection

Others

Events

Event Actions

-

-

-

Built-in; Varifocal f=3.6mm, F1.8

H: 63° H: 83°

Image Enhancement

Image Settings

WDR

DNR

Privacy Zone

Image Orientation

AES, AWB, AGC

Exposure Mode: AES / ALC / Flickerless / Manual;

White Balance: Auto / Manual;

Backlight Compensation

Configurable Brightness, Contrast, Hue, Saturation, and Sharpness

Gamma Correction

Enhanced Digital WDR

Configurable 3DNR setting

Yes, up to 8 privacy zones

Mirror, Flip

Frequency Control

Date & Time Stamp

NTSC(60Hz)/ PAL(50Hz)

Yes

Intelligent Video & Event Management

Motion Detection Yes, 3-level sensitivity

Network loss detection

Optimized i-frame (GOP) setting

Motion detection, ethernet detection

Event snapshot to remote FTP storage/ email recipients, HTTP event query, HTTP event client pulling

Event snapshot to remote FTP storage/ email recipients, Edge recording to SD card,

HTTP event query, HTTP event client pulling

Event snapshot, Manual Snapshot, Manual Recording

Two-way Audio

G.711 PCM 8kHz, a/μ-law support

1 in / 1 out for external microphone/speaker;

Built-in Microphone

Store Category

Local Storage

Memory Card Slot

Memory Card Overwrite

Network

-

microSDXC/SDHC card support

Yes

Protocol

Ethernet

ONVIF

ARP, DHCP, DNS, FTP, HTTP, HTTPS, ICMP, IGMP, IPv4, IPv6, NTP, RTSP/RTCP/RTP, QoS, SMTP, SNMP, TCP, UDP,

UPnP, IEEE802.1X

10Base-T/100Base-TX Ethernet connection for LAN / WAN, RJ-45

ONVIF

43

Browser

Security

Internet Explorer, Chrome, Firefox, Safari

Multiple user access levels with password protection; IP address filtering;

IEEE 802.1X network access control, HTTPS encryption, and digest authentication

I/O & Controls

Power

Power LED Indicator

Network

Audio In/Out

Analog Video

System Reboot

Factory Default

Power

Power Requirement

Power Consumption (Max.)

Mechanical

Dimensions(ΦxH)

Weight

Protection

Pan/Tilt Adjustment

Environmental

Operating Temperature

Operating Humidity

Storage Temperature

Regulatory

Approvals

All-in-one tail cable out, Female RJ-45 10BASE-T/100BASE-TX PoE

System power and status indicator

Female RJ-45

Terminal block 1 in / 1 out

1 x composite video out, micro JST

Reset x 1

Default x 1, pressing 5 sec for loading factory default

PoE (IEEE 802.3af), class 0

7.7W

Φ110mm x 47mm (Φ4.33" x 1.85")

340g (0.75 lb)

IP66 Certified, IP67/IP68 Compliant, IK10 Compliant

3-dimensional spherical lens angle adjustment

-40ºC ~ 50ºC (-40ºF ~ 122 ºF)

90% RH, non-condensing

-40°C ~ 60°C (-40°F ~ 140°F)

CE, FCC, RoHS

Note: Product specifications and pictures are subject to change without notice.

DC12V/ PoE (IEEE 802.3af, class 0)

8.5W

44