Tripp Lite RV1250ULHW Datasheet

Tripp Lite

1111 West 35th Street

Chicago, IL 60609 USA

Telephone: +(773) 869 1234

E-mail: [email protected]

Model #: RV1250ULHW

PowerVerter RV Inverter/Charger - Quiet Mobile Power for RV, Camping & Boating Applications

Highlights

12V DC or 120V AC input; 120V AC output (hardwired)

1250 watts continuous and 2500 watts DoubleBoost inverter output

3 stage, 14/55 amp selectable wet/dry cell battery charger

Built-in Isobar® premium AC surge protection and Auto Transfer Switching option for battery backup / UPS operation

Tested to power inverter standards UL458 (USA) and CSA (Canada)

High reliability large-transformer design with protected DC and AC wiring terminals

Description

Tripp Lite RV1250ULHW Inverter/Charger is the quiet alternative to gas generators with no fumes, fuel or noise to deal with! It provides equipment with utility- or generator-supplied AC electricity filtered through premium ISOBAR surge protection. This DC-to-AC inverter with automatic line-to-battery transfer and integrated charging system serves as an extended run UPS, a standalone power source or an automotive inverter suitable for rugged RV applications. Supplies up to 1250 watts of continuous 120V AC power from any 12V DC battery or automotive DC source.

OverPower TM inverter output feature temporarily provides up to 150% of the continuous output for 1-60 minutes, and DoubleBoost TM inverter output feature delivers up to 200% of the continuous output for up to 10 seconds, providing the extra power needed to cold start heavy-duty tools and motorized equipment. When hardwire AC input is energized, commercial power passes through to connected equipment and the battery set is recharged via 3 stage, selectable 14/55 amp charging system. In UPS mode, the APS system responds to blackouts and voltage fluctuations with a near instantaneous automatic transfer to battery-derived AC output. Includes a set of high current DC input terminals for simple installation (user supplies batteries and cabling - see owner's manual for recommendations). Passes sine wave utility or generator power during battery charging and

UPS line power operation, plus efficient PWM sine wave AC output in inverter and UPS backup modes. Reliable large transformer design, with frequency control powers resistive electronic loads or large inductive motors, compressors and other items with high current needs on startup.

Optional APSRM4 wired remote power switch with full status LEDs provides remote power inverter on/off switching and continuous status information (APSRM4 sold separately). Supports an unlimited amount of runtime with any number of user-supplied batteries connected. Highly adaptable to a variety of applications and site conditions with adjustable charger settings for wet/gel battery types and selectable line to battery power transfer voltages.

Applications

Versatile inverter/charger system with auto-transfer switching serves as an automotive inverter for RVs, over-the-road trucking, conversion vans and fleet service vehicles; a standalone alternative power source for off-grid, alternative energy or export applications and as an uninterruptible power supply (UPS) for items compatible with a 16.6 millisecond transfer time.

Package Includes

RV1250ULHW Inverter/Charger

Instruction manual with warranty information

Features

RV1250ULHW serves as an automotive or stationary DC-to-AC inverter with automatic line-to-battery transfer and integrated battery charger

RV1250ULHW serves as an automotive or stationary DC-to-AC inverter with automatic line-to-battery transfer and integrated battery charger

Supports 120V AC output from a 120V AC line power source or 12V DC battery source

16.6 millisecond automatic transfer between line and battery power supports UPS protection during blackouts and voltage fluctuations for equipment compatible with a one cycle transfer time

1250 watts continuous AC output in inverter mode, 2400 watts continuous AC output in AC mode

Double Boost inverter output supports momentary startup loads up to 200% of the continuous rating for up to 10 seconds

OverPower inverter output supports longer duration overloads to 150% for 1-60 minutes under ideal battery and temperature conditions.

(For best results, utilize OverPower usage for as short of a duration as possible, ensure battery bank and cabling is able to provide full nominal DC voltage under load and allow inverter/charger to fully cool before and after OverPower usage.)

3 stage, selectable 14/55 amp battery charger with adjustable settings for wet/gel battery types offers fast, reliable battery recharging

Protected hardwire bolt-down input lugs safely accept heavy gauge input wiring from attached battery bank

Protected hardwire output passes 120V line power or inverter output through to connected equipment

Reliability enhanced large-transformer design tested to UL (USA) and CSA (Canada) standards

Moisture-resistant construction enables vehicular or marine operation in high humidity environments

3 position operating mode switch supports "AUTO" mode to enable automatic transfer between DC and AC modes, CHARGE-ONLY to maintain a full battery charge when AC is present without auto transfer and SYSTEM OFF settings

Set of six front panel LEDs display AC/DC operational modes, overload status, DC voltage level, shutdown status and system fault status

Set of 4 configuration dipswitches support wet/gel battery charging profiles, adjustable 135/145V high voltage auto transfer during overvoltages and selectable 75/85/95/105V AC low voltage auto transfer during brownouts

Set of 4 additional configuration dipswitches support 4 levels of charger limiting relative to output load size, a battery equalization program and battery charger low/high settings

Resettable 12A charger AC input breaker and resettable 20A AC output breaker and automatic 2 speed cooling fan protect the inverter from load and temperature related failures

Grounding lug properly connects the inverter/charger system to earth ground or vehicle grounding system

Automatic overload and thermal shutoff safely turns off inverter as excessive loads or overheating conditions develop

Front panel remote control connector enables remote off/on switching (requires APSRM4 switch accessory). Optional APSRM4 accessory also includes user configurable jacks to support inverter shutoff or startup as a vehicle ignition is engaged

Front panel remote control connector enables remote off/on switching (requires APSRM4 switch accessory). Optional APSRM4 accessory also includes user configurable jacks to support inverter shutoff or startup as a vehicle ignition is engaged

Load sensing control dial enables adjustable load threshold required to automatically turn the inverter on and off in DC mode as load conditions change

Includes battery temperature sensor with 20 foot cable to prolong battery life by adjusting the charge level based on battery temperature

Automatic Generator Starter jack enables user configuration of automatic generator startup as inverter batteries drop to 11.5VDC and generator shutoff as inverter batteries are recharged to 14.1VDC

Specifications

OVERVIEW

Intended Application RV/Fleet/Alternative Power

OUTPUT

Frequency compatibility

60 Hz

Output watts 1250

1250 Continuous output capacity (watts)

Peak output capacity (watts)

2500

120V Output nominal voltage

Output voltage regulation

Output frequency regulation

Overload protection

LINE POWER (AC): Maintains 120V nominal sine wave output from line power source. INVERTER POWER (AC):

Maintains PWM sine wave output voltage of 120 V AC (+/-5%).

60 Hz (+/- 0.3 Hz)

Includes 12A input breaker dedicated to the charging system and 20A output breaker for AC output loads

Outlet quantity / type Hardwire

INPUT

Recommended

Electrical Service

DC INPUT: Requires 12V DC input source capable of delivering 95A for the required duration (when used at full continuous capacity - DC requirements increase during Over-Power and Double-Boost operation). For automotive applications, professional hardwire

Maximum input amps / watts

DC INPUT: Full continuous load - 95A at 12V DC. AC INPUT: 20 amps at 120V AC with full inverter and charger load

(12A max charger-only / combined input load to support charger and AC output is automatically controllable to

66%-33%-0% based on AC output lo

DC INPUT: Set of 2 DC bolt-down terminals. AC INPUT: hardwire Input connection type

Input cord length details

DC INPUT: User supplies cabling. 4 gauge or larger (see manual). AC INPUT: hardwire

Voltage compatibility (VAC)

120

Voltage compatibility (VDC)

BATTERY

Expandable battery runtime

DC system voltage

(VDC)

Battery Pack

Accessory (optional)

12

Runtime is expandable with any number of user supplied wet or gel type batteries

12

98-121 sealed lead acid battery (optional)

Battery recharge rate 14A / 55A (selectable)

LEDS ALARMS & SWITCHES

Switches 3-position on/off/remote switch enables simple on/off power control plus auto/remote setting that enables distant on/off control of the inverter system when used in conjunction with APSRM4 accessory (sold separately) in inverter mode.

Front panel LEDs Set of 6 LEDs offer continuous status information on load percentage (6 levels reported) and battery charge level (7 levels reported). See manual for sequences.

SURGE / NOISE SUPPRESSION

AC suppression joule rating

600

PHYSICAL

Shipping weight (lbs) 24.9

Shipping weight (kg) 11.3

Multi-speed fan

7 x 8.75 x 9

Cooling method

Unit Dimensions

(HWD/in)

Unit Dimensions

(HWD/cm)

Shipping

Dimensions

(HWD/in)

17.78 x 22.23 x 22.86

12.5 x 11 x 10.75

Shipping

Dimensions

(HWD/cm)

31.75 x 27.94 x 27.31

Unit weight (lbs)

Unit weight (kg)

Material of construction

23.3

10.57

Polycarbonate

Style

Low voltage transfer to battery power

Heavy-duty with built-in battery charger

Form factors supported

Transfer time from line power to battery mode

Mounting slots enable permanent placement of inverter on any horizontal surface (see manual for additional mounting information)

ENVIRONMENTAL

Relative Humidity 0-95% non-condensing

LINE / BATTERY TRANSFER

16.6 milliseconds (typical - compatible with many computers - verify transfer time compatibility of loads for UPS applications)

In AC "auto" mode, inverter/charger switches to battery mode as line voltage drops to 75V (user adjustable to 85, 95,

105V - see manual)

In AC "auto" mode, inverter/charger switches to battery mode as line voltage increases to 135V (user adjustable to

145 - see manual)

High voltage transfer to battery power

SPECIAL FEATURES

Appearance Attractive gray color scheme

Load Sensing Optional load sense function enables automatic inverter shutoff and startup as connected equipment is powered off and on. Front panel load sense potentiometer can be set to shutoff or turn on inverter power in response to loads of any level.

Yes Remote control capability

CERTIFICATIONS

Certifications

WARRANTY

Product Warranty

Period (U.S., Canada

& Puerto Rico)

Tested to UL458 (USA) and CSA (Canada)

30-month limited warranty

Related Items

Optional Products

Product Type Related Model

External Battery Housings BP-260

Audio Cables

Audio Cables

98-121

APSRM4

Description

Ideal battery housing for use with Tripp Lite PowerVerter APS inverter/charger systems with a 12 or 24V DC system voltage.

12V DC Sealed, Maintenance-Free Battery

Remote Control Module - for Tripp Lite Inverters and Inverter/Chargers

More information, including related products, owner's manuals, and additional technical specifications, can be found online at www.tripplite.com/en/products/model.cfm?txtModelID=3718 .

Qty.

-

-

-

Copyright © 2011 Tripp Lite. All rights reserved. All trademarks are the sole property of their respective owners. Tripp Lite has a policy of continuous improvement. Specifications are subject to change without notice. Photos may differ slightly from final products.