Kodak ULTRA MAX 400 Datasheet
Advertisement
Advertisement
KODAK ULTRA MAX 400 Film
TECHNICAL DATA / COLOR NEGATIVE FILM
KODAK ULTRA MAX 400 Film is a worry-free, easy-to-use high speed film designed for snapshooters. ULTRA MAX
400 Film gives you the flexibility you need to take consistently better pictures in more picture taking situations—better low-light picture quality with fewer underexposures, better results with zoom lenses, greater flash range, better "stop-action" photos, and reduced impact of camera shake.
Even when enlarged, ULTRA MAX 400 Film delivers excellent sharpness and fine grain for crisp, clear pictures.
Optimized color precision technology provides consistently bright, vibrant colors with accurate skin-tone reproduction for natural-looking people pictures.
ULTRA MAX 400 Film is designed for processing in
KODAK FLEXICOLOR Chemicals for Process C-41. It is printing compatible with KODAK GOLD Films.
FEATURES
• Advanced
T-GRAIN Emulsion technology
• Antenna dye sensitization
• Advanced development accelerators
• Optimized color precision technology
ADVANTAGES
• True 400 speed
• Outstanding underexposure latitude
• Long flash range
• Fine grain and high sharpness
• Great skin tones and superb color
BENEFIT
• Better pictures under more conditions (inside, outside, bad light, fast action)
STORAGE AND HANDLING
Load and unload your camera in subdued light.
Store unexposed film at 21
° C (70° F) or lower in the original sealed package. Always store film (exposed or unexposed) in a cool, dry place. Process film as soon as possible after exposure.
Protect negatives from strong light, and store them in a cool, dry place. For more information on storing negatives, see KODAK Publication No. E-30, Storage and Care of
KODAK Photographic Materials—Before and After
Processing.
DARKROOM RECOMMENDATIONS
Do not use a safelight. Handle unprocessed film in total darkness.
EXPOSURE
Film Speed: ISO/DIN 400/27 °
Use these speed numbers in the table below with cameras or meters marked for ISO, ASA, or DIN speeds or exposure
©Eastman Kodak Company, 2007
February 2009 • E-7023 indexes. Do not change the film-speed setting when you use a filter if your camera has through-the-lens metering.
For critical work, make a series of test exposures.
Daylight
Use the exposures in the table below for average frontlit subjects from 2 hours after sunrise to 2 hours before sunset.
Lighting Conditions
Shutter
Speed
(seconds)
Bright/Hazy Sun on Light Sand or
Snow
Bright or Hazy Sun (Distinct
Shadows) *
Weak, Hazy Sun (Soft Shadows)
Cloudy Bright (No Shadows)
Heavy Overcast, Open Shade †
1/500
1/500
1/500
1/500
1/500
* Use f/5.6 for backlit close-up subjects.
† Subject shaded from the sun but lighted by a large area of sky.
Lens
Opening
f/16
f/11
f/8
f/5.6
f/4
Electronic Flash:
Use the appropriate guide number in the table below as a starting point for your equipment. Select the unit output closest to the number given by your flash manufacturer.
Then find the guide number for feet or metres.
To determine the lens opening, divide the guide number by the flash-to-subject distance. If negatives are too dark
(overexposed), use a higher guide number; if they are too light (underexposed), use a lower number.
Unit Output
(BCPS) *
350
500
700
1000
1400
2000
2800
4000
5600
8000
Guide Number
Distance in Feet Distance in Meters
85
100
120
26
30
36
140
170
200
240
42
50
60
70
280
340
400
85
105
120
* BCPS = beam candlepower seconds
Automatic Flash Units: Set ISO / ASA selector to 400.
Fluorescent and High-Intensity Discharge Lights
For best results without special printing, use the color-correction filters in the table below as starting points when you expose these films under fluorescent and high-intensity discharge lamps. Use exposure times of
1/60 second or longer to avoid the brightness and color variations that occur during a single alternating-current cycle.
Though this film is tolerant of mixed-lighting situations, for best color results under uniform fluorescent or high-intensity discharge sources, use the exposure and filter recommendations given below. These recommendations are starting points.
Actual filtration may vary between lamps and lamp manufacturers. Depending on the specific source, additional filtration or special printing may be required to achieve best results.
Type of
Fluorescent
Lamp
Daylight
White
Warm White
Warm White
Deluxe
Cool White
Cool White
Deluxe
KODAK Color
Compensating Filters
40R
20C + 30M
40B
30B + 30C
30M
10C + 10M
Exposure Adjustment
+ 2 ⁄
3
stop
+ 1 stop
+ 1 stop
+ 1 1 ⁄
3
stops
+ 2 ⁄
3
stop
+ 2 ⁄
3
stop
Note: When you do not know the type of fluorescent lamps, try a 10C + 20M filter combination and increase exposure by 2 ⁄
3
stop; color rendition may be less than optimum.
Type of High-Intensity
Discharge Lamp
High Pressure Sodium Vapor
Metal Halide
Mercury Vapor with Phosphor
Mercury Vapor without
Phosphor
KODAK Color
Compensating
Filters
70B + 50C
10R + 20M
20R + 20M
80R
Exposure
Adjustment
+ 3 stops
+ 2 ⁄
3
stop
+ 2 ⁄
3
stop
+ 1 2 ⁄
3
stops
Note: Some primary color filters were used in the tables above to reduce the number of filters and/or to keep the exposure adjustment to a minimum. Red filters were substituted for equivalent filtration in magenta and yellow.
Blue filters were substituted for equivalent filtration in cyan and magenta.
Adjustments for Long and Short Exposures
You do not need to make any exposure or filter adjustments for exposure times of 1/10,000 second to 1 second.
Exposures longer than 1 second may require compensation and filtration.
2 KODAK ULTRA MAX 400 Film • E-7023
PROCESSING
Process in KODAK FLEXICOLOR Chemicals for Process
C-41.
Information on replenishment rates is available online at www.kodak.com/go/photofinishing.
JUDGING NEGATIVE EXPOSURES
You can check the exposure level of the color negative with a suitable electronic densitometer equipped with a filter such as the red filter for Status M Densitometry or a
KODAK WRATTEN Gelatin Filter No. 92. Depending on the subject and the light source used for exposure, a normally exposed color negative measured through the red filter should have the approximate densities listed below. These densities apply for the recommended light sources and correct processing of the negative.
Densities of Properly Exposed and Processed Negatives
Area Measured on the Negative Density
Reading
0.80 to 1.00
The KODAK Gray Card * (gray side) receiving the same illumination as the subject
The lightest step (darkest in the negative) of a
KODAK Paper Gray Scale receiving the same illumination as the subject
Normally lighted forehead of person with light complexion †
Normally lighted forehead of person with dark complexion †
1.20 to 1.40
1.10 to 1.40
0.85 to 1.25
* KODAK Publication No. R-27
† Because of the extreme range in skin color, use these values only as a guide.
For best results, use a KODAK Gray Card (gray side).
PRINTING NEGATIVES
This film is optimized for printing on KODAK EKTACOLOR
EDGE Paper, KODAK ROYAL Digital Color Paper, and
KODAK PROFESSIONAL ENDURA Metallic Paper.
Make color slides and transparencies by printing the negatives on KODAK PROFESSIONAL ENDURA
Transparency Display Material or KODAK
PROFESSIONAL ENDURA Clear Display Material.
You can scan an image to a file and print digitally to
KODAK EKTACOLOR EDGE Paper, KODAK ROYAL Digital
Color Paper, KODAK PROFESSIONAL ENDURA Papers,
KODAK PROFESSIONAL ENDURA Metallic Paper,
KODAK PROFESSIONAL ENDURA Transparency Display
Material, or KODAK PROFESSIONAL ENDURA Clear
Display Material.
Make black-and-white prints on any of the materials mentioned above using the recommendations in KODAK
Publication CIS-274, Printing Black-and-White Images
Without KODAK Black-and-White Papers.
RETOUCHING
Negatives on this film can be retouched on the emulsion side with retouching pencils, after applying a retouching fluid, such as KODAK Retouching Fluid.
IMAGE STRUCTURE
Print Grain Index Magnification Table:
The Print Grain Index number refers to a method of defining graininess in a print made with diffuse-printing illumination. It replaces rms granularity and has a different scale which cannot be compared to rms granularity.
This method uses a uniform perceptual scale, with a change for four units equaling a just noticeable difference in graininess for 90 percent of observers.
A Print Grain Index rating of 25 on the scale represents the approximate visual threshold for graininess. A higher number indicates an increase in the amount of graininess observed.
The standardized inspection (print-to-viewer) distance for all print sizes is 14 inches, the typical viewing distance for a 4 x 6-inch print.
In practice, larger prints will likely be viewed from distances greater than 14 inches, which reduces apparent graininess.
Print Grain Index numbers may not represent graininess observed from more specular printing illuminants, such as condenser enlargers.
The Print Grain Index numbers listed in this publication apply to the following standards:
Negative Size:
Print Size:
Magnification:
Print Grain Index:
24 x 36 mm
(135-size standard format)
4 x 6 inches
(10.2 x 15.2 cm)
4.4X
46
KODAK ULTRA MAX 400 Film • E-7023 3
CURVES
Characteristic Curves
4.0
Exposure: Daylight
Process: C-41
Densitometry: Status M
Log H Ref: -1.44
3.0
2.0
1.0
0.0
-4.0
E7023A
-3.0
-2.0
-1.0
LOG EXPOSURE (lux-seconds)
0.0
1.0
B
G
R
Spectral-Sensitivity Curves
4.0
3.0
Exposure: Daylight
Effective Exposure: 1/100 sec
Densitometry: Status M
Density: 0.2>D-min
2.0
Yellow-
Forming
Layer Magenta-
Forming
Layer
Cyan-
Forming
Layer
1.0
0.0
250
E7023B
300 350 400 450 500 550 600 650 700 750
WAVELENGTH (nm)
2
*Sensitivity = reciprocal of exposure (erg/cm ) required to produce specified density
Spectral-Dye-Density Curves
2.5
2.0
Typical densities for a midscale neutral subject and D-min.
Process: C-41
Midscale Neutral
1.5
1.0
Minimum Density
0.5
0.0
400
E7023C
500 600
WAVELENGTH (nm)
700
NOTICE: The sensitometric curves and data in this publication represent product tested under the conditions of exposure and processing specified. They are representative of production coatings, and therefore do not apply directly to a particular box or roll of photographic material. They do not represent standards or specifications that must be met by Eastman Kodak Company. The company reserves the right to change and improve product characteristics at any time.
KODAK ULTRA MAX 400 Film • E-7023 4
MORE INFORMATION
Kodak has many publications to assist you with information on Kodak products, equipment, and materials.
Additional information is available on the Kodak website.
The following publications are available from Kodak
Customer Service and from dealers who sell Kodak products, or you can contact Kodak in your country for more information.
E-30
E-7022
Storage and Care of KODAK Photographic Materials—
Before and After Processing
KODAK GOLD 100 and 200 Films
E-7024 KODAK ULTRA MAX 800 Film
E-4035 KODAK PROFESSIONAL ULTRA COLOR Films
E-4040 KODAK PROFESSIONAL PORTRA Films
E-7020 KODAK EKTACOLOR EDGE Paper
E-7021 KODAK ROYAL Digital Color Paper
E-4020 KODAK PROFESSIONAL ULTRA ENDURA Paper
E-4021 KODAK PROFESSIONAL PORTRA and SUPRA ENDURA
Papers
E-4038 KODAK PROFESSIONAL ENDURA Transparency and Clear
Display Materials
For the latest version of technical support publications for KODAK
Products, visit Kodak on-line at: http://www.kodak.com
If you have questions about KODAK Products, call Kodak.
In the U.S.A.:
1-800-242-2424, Monday–Friday
9 a.m.–7 p.m. (Eastern time)
In Canada:
1-800-465-6325, Monday–Friday
8 a.m.–5 p.m. (Eastern time)
Note: The Kodak materials described in this publication are available from dealers who supply Kodak products.
You can use other materials, but you may not obtain similar results.
KODAK ULTRA MAX 400 Film • E-7023 5
KODAK ULTRA MAX 400 Film
Kodak, Kodak Professional, Edge, Ektacolor, Endura, Flexicolor, Gold, Max, Portra, Royal,
Supra, T-Grain, Ultra, and Wratten are trademarks.
Revised 2/09
Printed in U.S.A.
KODAK ULTRA MAX 400 Film
KODAK Publication No. E-7023
Film & Photofinishing Systems Group
EASTMAN KODAK COMPANY
• ROCHESTER, NY 14650
Download
Advertisement