- Computers & electronics
- Networking
- Telephone switching equipment
- Patch panels
- Tyco Electronics
- AMP NETCONNECT MRJ21 Series
- User manual
advertisement
▼
Scroll to page 2
Instruction Sheet AMP NETCONNECT* 408-8974 MRJ21* 24-Port 10/100/1000BASE-T Straight Patch Panels 1777029-[ ] 19 JUN 08 Rev D Front of Patch Panel Blank Label Pad (24 Places) 12-24 Screw (4 Places) Port Identification 1 (24 Places) Assembly (4 Places) 6 RJ45 Connector EIA Rack (Ref) AMP NETCONNECT* AMPTRAC* Printed Circuit (PC) Board Subassembly (Patch Panel -2 Only) Back of Patch Panel HDP-22 Connector Port Identification (Patch Panel -2 Only) (4 Places) AMPTRAC Port Identification MRJ21 Receptacle (Patch Panel -2 Only) (4 Places) Figure 1 1. INTRODUCTION MRJ21 24–Port 10/100/1000BASE–T Straight Patch Panels 1777029–[ ] are designed to be mounted onto a standard 483–mm [19–in.] Electronic Industries Alliance (EIA) rack or equipment cabinet as shown in Figure 1. Patch Panel –2 is designed for use with the AMP NETCONNECT AMPTRAC system. Read these instructions thoroughly before starting installation. To obtain information on AMP NETCONNECT products, call PRODUCT INFORMATION at the number at the bottom of this page, or visit the AMP NETCONNECT website at www.ampnetconnect.com. Reasons for reissue of this instruction sheet are provided in Section 6, REVISION SUMMARY. 2. DESCRIPTION NOTE All numerical values in this instruction sheet are in metric units [with U.S. customary units in i NOTE brackets]. Dimensions are in millimeters [and inches]. Figures are not drawn to scale. For Patch Panel -2, these instructions assume that the reader understands the operation of i equipment and software used with the AMPTRAC system. AMPTRAC Retrofit Kit 1479894–1 can be installed onto Patch Panel –1 to enable the patch panel to be connected to the AMP NETCONNECT AMPTRAC system. Back Cable Manager Kits 1933352–[ ] or Wiring Distribution Bracket Kit 557548–1 must be used to support the cable. E 2007 Tyco Electronics Corporation, Harrisburg, PA All International Rights Reserved Each patch panel contains four MRJ21 receptacles (one per 1 6 RJ45 connector assembly). The ports are identified by numbers printed on the front and on the back of the patch panel, and blank label pads are provided on the front for identifying connecting ports. Four 12–24 screws are included to mount the patch panel to the rack. In addition, Patch Panel –2 has a pc board subassembly and HDP–22 connector to enable the patch panel to connect to the AMP NETCONNECT AMPTRAC system. 3. INSTALLATION 1. Using the screws, mount the patch panel onto the rack. Refer to Figure 1. TOOLING ASSISTANCE CENTER 1-800-722-1111 This controlled document is subject to change. PRODUCT INFORMATION 1-800-522-6752 For latest revision and Regional Customer Service, TE logo and Tyco Electronics are trademarks. *Trademark. Other products, logos, and company names used are the property of their respective owners. visit our website at www.tycoelectronics.com 1 of 2 LOC B 408-8974 MRJ21 24-Port 10/100/1000BASE-T Straight Patch Panels 1777029-[ ] 2. Plug a connector (from the trunk cable) into each MRJ21 receptacle (at the back of the patch panel). Refer to Figure 2. Make sure to align the keying features of the connector and receptacle. Ensure that the connector is fully seated, then using a small cross–recessed tipped screwdriver, turn the jack screws of the connector clockwise and tighten to a maximum torque of 0.23 Nm [2 lbf–in.]. CAUTION To avoid damage to the connector, DO NOT 1 1 2 13 14 6 RJ45 Connector Assembly 3 4 5 6 7 8 9 10 11 12 15 16 17 18 19 20 21 22 23 24 over-tighten the jack screws. DO NOT use an ! (Front of Patch Panel) MRJ21 Receptacle automatic screwdriver. (Back of Patch Panel) Note: For Reference, Ports Labeled 1 Through 6 Are Shown 3. Using the blank label pads, identify the connecting ports. Pair 4 5 4. For Patch Panel –2, plug the connector of the I/O cable assembly (PN 1499507–[ ]) from the analyzer into the HDP–22 connector (at the back of the patch panel). See Figure 2. 5. Install the bracket onto the rack. Using cable ties or similar fasteners, attach the cables to the bracket. It is recommended to maintain a minimum bend radius of 50.8 mm [2 in.] when securing and routing cables. See Figure 2. NOTE 6 Pair 7 3 4 back cable manager, refer to Instruction Sheet 408-10170. 4. TROUBLESHOOTING For port–to–cable pair cross–reference, refer to Figure 3. Connector Plugged Cable into MRJ21 Connector Bracket (4 Places) (Ref) Trunk Tie Cable Pair 1 Pair 2 1 2 Pair 8 For installation procedure for the wiring Pair 6 Pair 5 CABLE PAIRS PORT distribution bracket, refer to Figure 2; for the i Pair 3 (4 Pairs Per Port) 1 13 1, 2, 3, 4 2 14 5, 6, 7, 8 3 15 9, 10, 11, 12 4 16 13, 14, 15, 16 5 17 17, 18, 19, 20 6 18 21, 22, 23, 24 7 19 1, 2, 3, 4 8 20 5, 6, 7, 8 9 21 9, 10, 11, 12 10 22 13, 14, 15, 16 11 23 17, 18, 19, 20 12 24 21, 22, 23, 24 Figure 3 5. REPLACEMENT AND REPAIR Patch panels are not repairable. DO NOT use a patch panel with damaged or defective connectors. Connector Plugged EIA Rack Front of (Ref) Patch Panel into HDP-22 Connector (Patch Panel -2 Only) Figure 2 2 of 2 6. REVISION SUMMARY Revisions to this instruction sheet include: S Added text to Steps 2 and 5 and CAUTION of Section 3 Tyco Electronics Corporation Rev D
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project