QVIS G3-mini keyboard User manual

Keyboard Controller
Users Manual
V2.0 11.14
CATALOGUE
1. Summ ary------------------------------------------------------------------------------------------- --------1
1.1 Notice-------------------------------------------------------------------------------------------------1
1.2 Function and Characteristic-------------------------------------------------------------------------1
1.3 Technical Data----------------------------------------------------------------------------------------1
2. Keyboard Connection------------------------------------------------------------------------------------2
2.1 Keyboard Interface Instruction------------------------------------------------------------- -------2
2.1.1 Rs422 and Rs485-----------------------------------------------------------------------------2
2.1.2 RJ45 Interface--------------------------------------------------------------------------------2
2.3 Matrix Connection-----------------------------------------------------------------------------------3
2.3.1 RJ45 Local Connection---------------------------------------------------------------------3
2.3.2 RS422 Remote Connection------------------------------------------------------------------3
2.4 Connect with The Dome Direct ly-------------------------------------------------------------------4
2.5 The Connection of The Keyboard in The System--------------------------------------------- ----5
3. Keyboard operation manual----- ---- ------------ ---- --------- --- --------- ---- ---- --------- -----6
3.1 Current-carrying to keyboard----------- ---------------------- ---------- --------------- ---------------6
3 .2 LCD----------- ---------------------- ---------- ----------------------------------- ---- ---------6
3.3 Joystick cont rols dome ---------- ---------------- - ------------------------ ------- -----------------------6
3.4 Change object dom e---- ---- -- ------------------ - -- -------- -------- ------- -------- - - -- ---- ---- -----------7
3.5 C ontrol d ome lens- ------------------------------------ ---------------------------- ----------------------7
3.6 Set dome function---------- ---------------------- ------------------------- --- ------------- ------------7
3.6.1 P reset---- -------- --- ----------- ----- ------ ---------------- -------- -------- - --------- ---- - 7
3.6.2 Scan-- -- ----- --------- --------- --------------- --------- ----- ---- ----- ---- - - --------- --7
3.6.3 Pattern--- ---- --- ---- ------- ------- ----------------- ------- ------- ------- ------- ----------8
3.6.4 Tour- --------- ---- ------------------------ --------- -- -- ------- -- -- --------- -- --------- -----8
3.7 Cal l dome main menu---------- ------------------ ------------------------------- ---- ---- -------------8
3.8 Control matrix-------------- --------------------------- - -- ----------------------------------------------8
3.8.1 Switch dome in order-------------------------- -- -------------------- ---------- --- ------------8
3.8.2 Call matrix main menu-- ---------- ------------------------------------------------ ------------ 8
3.8.3 Confirm after pr ogram--------- ----- ------ ---- ------- ---- ----------- ------------- -- --------- -----8
3.8.4 Change object monitor ---------------------------------------------------------------------------8
4. Keyboard control----------------------------------------------------------------------------------------9
4.1 keyboard index setting--------------------------------------------------------------------- --------9
4.1.1 Set ID number--------------------------------------------------------------------------------9
4.1.2 Set the baud rate-----------------------------------------------------------------------------9
4.1.3 Joystick calibration------------------------------------------------------------------------10
4.1.4 Multi keyboard state------------------------------------------------------------------------10
4.1.5 Keyboard message display---------------------------------------------------------------- 10
4.2 Dome setting----------------------------------------------------------------------------------------10
4.2.1 Dome preset setting-------- ----------------------------------------------------------------11
-------------------------------------------11
4.2.2 Dome scan setting---------------------------------4.2.3 Dome patt ern setting------------------------------------------------------------------------12
4.2.4 Dom e tour setting----------------------------------------------------------------------------12
4.3 Protocol setting-------------------------------------------------------------------------------------12
4.3.1 Pelco matrix model---------------------------------------------------------------------------13
4.3.2 Dome control ling mode----------------------------------------------------------------------13
4.4 Exit keyboard menu----------------------------------------------------------------------------------13
5.A ppendix--------------------------------------------------------------------------------------- -----------14
5.1 Rs485 Bus Basic Knowledge------------------------------------------------------------------------ 14
5.2 Keyboard shortcut operation manual--------------------------------------------------------------15
6.Keyboard Menu Index------------------------------------------------------------------------------------16
Summary
1. Summary
This keyboard can be unversally used to control PTZ
cameras within a wide variety of security control room
environments. The keyboard has been equipped with a 2D
& 3D joystick, which can control the movement of the
camera and the zoom magnification lens. It also
incorporates an LCD screen with backlight enabling you to
read the screen details in a variety of locations with
varying light levels. The screen displays the current
operation order, the control protocol's name, the current
PTZ camera's ID, the current monitor's ID, and also what
the current state the joysticks are in. Controlling the your
CCTV with the joystick will make security processes quick
and efficient.
1. 1 Notice
●
Ple ase rea d the manua l ca refully a nd heed
instructions contained within
●
Please do not p lace the key boa rd in a d a m p
environment.
●
Please do not place the keyboard next to sources of
high heat.
1.3 Technical Data
1. 2 Function and Characteristic
◆ E lectrical
●
Inpu t voltage：9 V-12V AC/DC
Rs485 Bus Line, an d a keyboard can conn ect t o
R ate d power ：2.5W
31 d omes in the dire ct c ontrol mode.
●
It can be compatible with all kinds of protocols
.
◆ Co mm unicatio n
Co mmunicatio n in terface ：
RS485×1，R S42 2×1 ,RJ45
●
You can co ntro l the Iris 、L ocus and Zoom.
Co mmunicatio n frequency：
●
You can se t an d ca ll th e prese t, ru n sc an、 pattern
Co mmunicatio n dista nce：
24 00 ,480 0, 9600、19200Bps
a nd tour.
●
You can co ntro l the ma trix,
1.2km （R S485 an d R s422 can achiev e it ）
◆ Operational environment
thr ough w h i c h wh ich can control the dome
Operating temperature：0℃ ～ 50 ℃
indirectly.
Re lative h umidity ：le ss th an 90%
●
It h as b een
equipped w ith the 2D/3D jo ystick a nd a la rge LCD
scree n.
◆ Ph ysical p roperties
L*W*H =218*180*55（ mm ）
W eight：6 30g（N et Weight）
1
Connection
2. Keyboard Connection
2.1 Keyboard Interface Instruction
There is a n interface on the back of the keyboard,
which allows you to either have a direct
connection to the PTZ cameras or a connection
via a network.
2.1.2 RJ45 Interface
This is the standard network interface, which is mainly
used for connecting the keyboard with the control matrix
over short distances (less than 7.6m). For more details
please see "2.3 matrix connection".
2.1.1 RS422 and RS485 interface
Rs422 and Rs485 interface are on the 6bit
ribbon cable connection of the keyboard.RS485
(A+ B-) can connect with the dome when the keyboard controls the dome directly;RS485（A+，B-）
can connect with DVR or other keyboards when
the keyboard controls the dome by matrix; Rs422
(T＋,T－) is sending the signal ,RS422(R ＋,R－)
is receiving the signal , both of which can connect
with matrix, DVR and so on.
Picture 2-1.1
Picture 2-1.2
6Bit Ribbon
Cabl e
2
RJ45
Pow er Sup ply
Port
Connection
2. 2. 2 Rs422 remote connection
2. 2 Matrix Connection
The keyboard can control the PELCO protocols
CM6700 & CM6800. For example the keyboard
connects with the PELCO CM6700 matrix in order to
introduce the connection between the keyboard and
the matrix.
Rs422 connection line, one end connects with
There are two kinds of keyboard connection
interface on the CM6700 matrix back plate. One is
the local keyboard connection interface RJ45
("LOCAL KEYBOARD"), which can control the single
keyboard within the distance of 7.6m. The other is
the remote interface RS422 ("REMOTE
KEYBOARD(s)"), which can connect with the
keyboard's RS422 Iinterface. The maximum distance
is 1200m.
erface Rs422（T+ T-）, the keyboard interface Rs
Rs422 interface（REMOTE KEYBOARD(s)) of
CM6700 back plate, the other end connects with
Rs422 interface of the keyboard, the keyboard interface Rs422（R+ R-）corresponds with matrix in422 （T+ T-）corresponds with matrix interface Rs
422 （R+ R-）.
Rs422 rem ote co nnectio n, the m aximum
di stance b etween the key board a nd the
NOTI CE
m atrix is 1200m.
2. 2. 1 RJ45 Local Connection
Pleas e insert one end of RJ 45 connec tion
line into the R j45 interface of the keybo ard, an d
insert the o ther one into the R J 45 interfac e
(“LO C AL KE YB O ARD ”）of CM67 00 ma trix
1、RJ45 loca l conne ction, t he dista nce between
th e keybo ard and the ma trix is le ss than 7.6m.
Key board 1
2 、RJ45 inte rface h as 12VA C, no other power
NOTICE
Pin8
Pin1
is needed when the keyboard connects to the
CM6700 matrix.
RJ45
RJ-45 Limb
Po wer input
AC /DC 9V-1 2V
Keyboar d 2
Pin1
2
3
4
T+
T-
Pin5
NC
6
7
8
NC
RR+
9V-12VAC/DC
NONPOLAR
ALARMS
(1-9)
RS485
ALARMS
(1-18)
RS422
R+
R-
R+
R-
T+
T-
RR
-+
COM1 ( 1-6 )
COM2 (7-12)
Matrix
T+
T-
RJ45
Rem ote K eybard (S)
TT
+-
A+ B- T+ T- R+ RKeyboard
Loc al Key board
CONTROL
OUTPUTS
CM 6700 Matrix
Picture 2-2.1
3
Connection
2. 3 Connect with The Dome Directly
You can connect to the PTZ camera/dome via the RS485
interface on the keyboard if you want to control it directly.
The RS485 interface of the PTZ camera/dome is on the
switchboard of the pendant hanger found on the upper
cover of the PTZ camera/dome. You will also find the 4
Pin control/power socket and also the RS485 A+ & Bwhen you turn the metal button inside the hanger and
opened the switchboard.
There are different ways to connect to the PTZ camera/
domes depending on the make of them. Please see the
PTZ camera/dome's user manual for more information.
AC24VRS485
A+ B-
RS485 RS422
A+ B- T+ T- R+ R-
Power AC/DC 9V-12V
Keyboard
P icture 2-3.1
4
Dome
Connection
2. 4 The Connection of The Keyboard in
The System
The keybo ard controls the matrix and then control
the domes ind irectly by the matrix（sees to the picture
2.4-1）W hen unconnect with the m atrix, the keyboard
controls the dome directly.
The keyboard and camera connects in parallel with the
RS485 Bus and each keyboard can control each dome. This
way is required because you need to have the keyboard's
(the main keyboard ID is set to '1') Baud rate set to 9600bps
(see picture 2-4-2).
Matrix
Picture 2.4-1
Keyboard
Dome1
NOTICE
Keyboard 1
Dome2
1. A line of Rs485 may control up to 32 main
controlling and under controlling e quipments,
so a keyboard which controls the dome directly
may c onnect up to 31 domes.
2. The system may connect up to 4 k eyboards at
the sa me time, and the fou r keyboards ID are
different.
Keyboard 2
Keyboard 3
Dome1
Dome2
Dome3
Dome4
Dome5
Dome6
Dome7
Dome8
Keyboard 4
Picture 2.4-2
5
Connection
3. Keyboard Operation Manual
LCD
Jo ys tic k
Function
Numeric zone
Lens Controlling
Picture 3-1.1
3. 2 LCD
This section of the manual explains how to operate the
actual keyboard. It needs to be noted that the
systematic platform of the keyboard compared to the
PTZ camera/dome may differ. Please refer to the PTZ
camera/dome's users guide to make sure that both
devices work together successfully.
The LCD display is used to list the keyboard's basic
operational information, which includes camera control,
monitor ID, baud rate, etc. In the last line it shows the
keyboard input commands and joystick operation. As the
image in Picture 3-1-1 shows, when you operate the
keyboard the LCD's backlight will turn on so you are able to
view the screen's information more clearly. The backlight
will switch off after 15 seconds of non use.
3. 1 Electrify to keyboard
When power is provided to the keyboard, the keyboard
will auto-test the baud rate, protocol and the PTZ
cameras/domes (object monitor will be set as '1'). This
information will show on the LCD screen.
Cam ID:001 Mon ID:001
Protocol: Factory
Baudrate: 9600bps
Pictu re 3-1.2
1 .when t he keyb oard is initializ ing, the joystic k
m ust to r eturn 0, can no t to pull or rotat e the
NOTICE
6
joystick.
Connection
● Focus control：
3. 3 Joystick controls the dome
The Joystick has two functions, one is to manually
control the PTZ camera/dome's rotation, and the other
is to help control the set up of the object menu.
Rotate the joystick in any direction, the camera will
rotate in correspondence with the direction of the
joystick at the same time. The LCD will display the
information in the lower right corner as directional
arrows. They respectively show tilt up, tilt down, tilt right,
tilt left. If the joystick tilts to the upper right hand corner,
the image will display the relevant directional arrows.
When the joystick returns to the primary location, the
camera will stop rotating.
●
● You can tilt the joystick up or down to scroll through
the system menu options. When you tilt it to the right
you will select that menu option or reserve the setting
after it has been set. Tilting it left will exit menu or stop
reserving the settings.
By moving the joystick more quickly the more the PTZ
camera/dome pan/tilts in parallel with the speed of
movement.
●
Press 【FAR】manually far focus, to make the
far object more legible, leave to stop.
Press 【NEAR】manually near focus, to make
the near object more legible, leave to stop.
The standard setting for the camera is for it to be in
constant auto focus. The user must manually focus
and run other operations by the two keys, once this is
done the camera will automatically resume to auto
focus.
● Iris control：
Press 【OPEN】manual Iris increase, Iris is
at the maximum, the screen will show white, leave
to stop.
Press 【CLOSE】manual Iris reduction, Iris is
at the minimum, the screen will show black, leave to
stop.
3.6 Dome function operation
3.6.1 Preset
●
Set preset： 【SET】+【N】+【Preset】
●
Call preset： 【N】+【Preset】
【N】means preset number.
3. 4 Change object dome
3.6.2 Scan
【N】 + 【Cam】
【N】means numeric key
Input the dome ID， Press【 Cam】
，
to change object
dome.
●
Set left limit：
●
Set right limit：【SET】+【2】+【Scan】
●
Run scan：
【SET】+【1】+【Scan】
【1】+【Scan】
User should enter into menu setup t o change
the speed of scan.
3. 5 Dome lens control
● Zoom control：
Press【TELE】, the camera's lens will zoom in
to increase the image size by multiple amounts.
Press【WIDE】, the camera's lens will zoom
out to decrease the image size by multiple
amounts.
3.6.3 Pattern
● Set
pattern path：【SET】+【N】+【PATTERN】
+Path+【SET】+【0】+【PATTERN】
Press【SET】, input pattern NO.（1-4）,
Press【PATTERN】to enter tour setup, the
dome records a series of motions, when c o mplete
press【SET】, then press【0】,then press【PATTERN】, the pattern setup finish.
● Run
pattern：【N】+【PATTERN】Input pattern
number（1-4）,press【PATTERN】,run pattern.
7
Connection
3.6.4 Tour
3.8.4 Change object monitor
Run tour： 【N】 + 【TOUR】/【TOUR】
【N】 + 【MON】
Press tour number，press【TOUR】，run tour.
Input the monitor ID, then press【M ON】，the
If system has only a tour, press【TOUR】directly.
image and the menu of the dome that you control
A set tour must b e enter e d i n t o t h e
setup menu.
by keyboard will display in the object monitor.
3. 7 Call the dome main menu
【9】+【5】 + 【Preset】：input 95, then press
【Preset】to call the main menu of object dome.
The menu is displayed in the object monitor.
How to set the dome menu by keyboard,
Please refer to the dome Operation manual.
3. 8 Control the matrix
3.8.1 Switch the domes in order
The matrix connects sixteen domes, and switches
the dome to previous and t h e next dome. The LCD
will display number, date and time.
【PREV】: switch to previous dome. Press
【PREV】, switch to previous dome in a single step；
Press 【PREV】 to hold it for 2s, and jump sixteen
domes of the connection matrix in previous order.
Press【Stop】to stop to switch.
【NEXT 】:switch to next dome. Press【NEXT 】
to switch the next dome in single step; press【NEXT】
to hold it for 2s, and jump the sixteen domes of the
connection matrix.
【Stop】: switch continuously, press 【Stop】to
stop to switch.
3.8.2 Call main menu of matrix
【Shift】+【Set】：
Calls the main menu. The
main menu will be displayed in the object monitor. If
you are unsure how to change settings in the matrix
menu please refer to the matrix's operation manual.
3.8.3 Confirm after program
【ENTER】：after the matrix programmed,
press 【ENTER】, means confirm after program,
for a detail e d explanation, please
refer to the matrix operation manual.
8
Keyboard Parameter Setting
4
The Keyboard Menu Controls
Press【SET】, hold for 2 seconds. Go to the main
menu, the LCD will show the following in Picture 4.1-1.
3. Press 【 1 】 to choose keyboard
Specification. LCD will display the following (See
picture 4.1.1-3)
1、Set KB ID
2、Set balldrate
3、Joy_calibrate
Press the numerical key or move the
joystick up and down to the option t h a t you need
and then m o v e it right after entering the main
menu, which can enter the relevant menu setting.
1、Keyboard setup
2、Dome setup
3、Protocol select
4、Exit menu
Pic ture 4.1.1-3
4. Press 【 1 】 to choose keyboard ID setting.
LCD will display the following (See picture
4.1.1-4)
Input KB ID:
（1-64）
Picture 4.1-1
* Saving Setting
Choose the relevant numerical keys according to the
menu hint. You can the enter the relevant function
settings. Press【ENTER】to save settings; the LCD
will display "Success" after the set up is successfully
complete.
Picture 4.1.1-4
Press the relative numerical key (1-64); press
【ENTER】to confirm. The screen will display the
following (See picture 4.1.1-5). This means that the
operation has been completed successfully.
Success！
* Return to P revious menu
Press 【Prev 】,or move the joystick le ftw ard s,
then retur n t o the previous menu .
Picture 4.1.1-5
The screen will show 'Error' if the inputted numerical
key is in excess of the ID scope (1-64). See picture
4.1.1-6.
Error!
4. 1 Keyboard Parameter Setting
4. 1. 1 Set keyboard ID
1. Enter main menu,LCD display ( See
picture 4.1.1-1 )
1、Keyboard setup
2、Dome setup
3、Protocol select
4、Exit menu
Picture 4.1.1-6
5. Press the 【PREV】button or move the joystick to
the left to go back through the menu stages
gradually.
The fa ctory d efault I D of th e keybo ard is 1 ;
The ID Numb er must be 1 if the sin gle key board
works ; It can connec t up to 4 keybo ard wh en
Picture 4.1.1-1
2. Press 【 1 】 then choose keyboard
setting. LCD will display the following
(See the picture 4.1.1-2)
NO TICE
worki ng on li ne, but make sure there is only a
keybo ard ID set as 1 ,otherwise all the onli ne
keybo ards ca n not w ork nor mally.
1、Set KB Parameter
2、About keyboard
Pict ure 4.1.1-2
9
Keyboard Parameter Setting
The joystic k must be u n t o u c h e d d u r i n g
4. 1. 2 The keyboard baud rate setting
Enter menu (LCD display - see picture
joystic k calibration .
NO TICE
4.1.1-1)
Press
【 1 】 to set the keyboard
LCD display ( sees picture 4.1.1-2)
Press 【2】to set the keyboard ' s baud rate.
LCD display (See picture 4.1.2-1)
Press 【4】 to set multi-keyboard connection
state setting.After you select 【Multi keyboard
The baud rate is divid ed into 2400bps,4800bps,
9600bps and 19200bps,user can choose baud rate
according to the application and then press【Enter】
to save. The screen display success It means the
operation is success . Then Press 【Prev】or move
the joystick t o t h e left to go bac k.
state】, tilt up/down the joystick to set the state
as “ON” or “ OFF”, the default setting of keyboard
is OFF. When it is set to ON, it can support multikeyboard operation, there will be no interference or
confusion between them. One group can support up to 4
keyboards when the Multi-keyboard setting is set. When
there is only one keyboard being used, the address
much be set as 1, or you will not be able to control the
keyboard.
9600 BPS when con nectin g with the
mat rix; and must use
NOTICE
4.1.1-1 shows.
LCD will display as Picture 4.1.1-2 shows.
Pict ure 4.1.2-1
use
Enter into t h e OSD menu, LCD will display as Picture
Press 【1】 to set the keyboard.
2400 bps
4800 bps
9600 bps
19200 bps
Mus t
4. 1. 4 Multi-keyboard Connection state setting
9600BPS or 1 9200b ps
when conne cting the keyb oard o nline.
I n mult i-keybo ard sta te the b aud ra te of ea ch
k eyboa rd shou ld be s et as 96 00bps.
NO TICE
4. 1. 3 Joystick Calibration
User c a n enter into the Joystick calibration menu
andcalibrate the joystick when it can not be controlled.
The joystick must b e i n i t s u n m o v e d state
4.1.5 Keyboard message display
when you do it.
E nter th e main menu.
Enter the main menu
L CD dis play. ( s ee pic ture 4.1.1-1)
Press【2】to check the keyboard message
P res s
【 1 】 to c hoose the key board setting .
LCD display(see picture 4.1.4-1)
L CD dis play. (s ee pic ture 4.1.1-3)
P res s
Version:1.00
KB ID:001
Protocol:Factory
Balldrate:9600bps
【 3 】 to enter Jo y stick C alibra tion.
LCD d isplay (see pic ture 4.1.3-1)
Joystick is free then
Press Enter
Pict ure 4.1.4-1
Pres s 【
】
v
or m ove
Picture 4.1.3-1
Press 【ENTER】to finish the operation. The screen will
display the following (see picture 4.1.3-2)
Success！
Picture 4.1.3-2
10
Press 【PREV】or move the joystick to the left to
return. The keyboard message menu will display the
keyboard's parameter setting,the keyboard model, ID
address, the Keyboard protocol and the keyboard baud
rate.
Keyboard Parameter Setting
4. 2 Dome setting
Press 【PREV】to go back to the former menu.
You will need to refer to the matrix and PTZ
camera/dome manuals to help complete the
setup using the keyboard. Some parameters to
be set my differ depending on the camera/dome
used.
NO TICE
4.2.1 Dome preset setting
En ter the main m enu, as LCD show s t h e
f o l l o w i n g (Pic ture 4.1.1-1)
Press
【 2 】 to e nter dome setting m enu, as
Af ter entering th e c a m e r a ' s prese t menu , the
joystick w ill con trol th e c a m e r a directly,
at th is tim e the k eys in t h e lens co ntrol
area also ca n co ntrol th e c a m e r a lens ,
the ope ration of the j oysti ck and the
key s a r e inva lid for the do me und er the
ge neral m enu mode.
4.2.2 Dome scan setting
Press '2' to enter the calling preset menu, the LCD will
display the following as shown in Picture 4.2.1-5.
LCD shows t h e f o l l o w i n g (Picture 4.2.1-1);
move joys tic k up an d down to separately set
t h e d ome pres et, s can, p attern and tour.
1、Set dome preset
2、Set dome scan
3、Set dome pattern
4、Set dome tour
Picture 4.2.1-1
Press
【 1 】 to en ter dome preset setting,
as LC D shows i n (Pictu re4.2.1-1).
【 1 】
Input corresponding preset number, press
【Enter】 to call preset, LCD will show ( Success )
tilt the joystick left or press【Prev】 to back to the
former menu.
Press 【3 】to enter the clearing preset menu,
As LCD shows (Picture 4.2.1-6)
Preset num:
（1-255）
Pic ture 4.2.1-2
Picture 4.2.1-6
item calls dome preset; the
third item clears the dome preset.
Choose
Picture 4. 2.1-5
1、Save preset
2、Show preset
3、Clear preset
The first item is t o s a v e t h e setting dome
preset; the second
Preset num:
（1-255）
to enter preset setting,
this item requires inputting the preset
number that you want to save, t h e LCD w i l l
d i s p l a y w h a t i s s h o w n i n Picture 4.2.1-3
Preset num:
（1-255）
Press prev to back
Picture 4.2.1-3
After entering the setting dome preset menu, the
joystick will control the dome directly. Input the
Input the preset number that you want to clear,
press 【 E N T E R 】 clear preset, LCD will show
(Success ) and g o back to the former menu.
Enter the menu, as LCD shows (picture 4.1.1-1)
Press【2】 to enter the dome setting menu, as
LCD shows (picture4.2.1-1)
Press【2】again to enter the dome scan setting
menu, as LCD shows (picture4.2.2-1)
1、Set left limit
2、Set right limit
3、Run scan
Picture 4.2.2-1
corresponding preset number, then press 【Enter】
Dome scan setting includes setting dome left li-
to save, LCD will show ( Success ). As picture 4.2.1-4
mit, right limit and running scan.
shows.
Choose 【 1 】 to set dome left limit, as LCD
shows (Picture 4.2.2-2)
Success！
Picture 4.2.1-4
11
Keyboard Parameter Setting
Press enter sure
Press 1 to start
Press 0 to stop
Press prev to back
Press prev to back
Picture 4.2.2-2
Picture 4.2.3-2
After entering the setting dome limit menu, to
move the dome in an appropriate position, then
press 【Enter】to save, LCD will show ( Success )
and w i l l g o back to the former menu.
Choose the second item (Set right limit), i t i s
t h e same operation w h e n s e t t i n g left limit.
Back to scan menu, then press【3】to run scan.
NOTICE
After entering the set ting c a m e r a pat tern
menu, the joystick will cont rol the dome
directly, at this time the keys in l ens
controlling area also can control the dome
lens, th e operation of the joystick and the key
is invalid for the dom e under gen eral me nu
mode.
4.2.4 Tour setting
Press【2 】to enter dome setting menu, as LCD
shows (picture 4.2.1-1)
NOTICE
After en tering t he c a m e r a limi t s e t u p
menu , the jo ystick will co ntrol the c a m e r a
directly, at this ti me the keys in t h e
lens c ontrol are a c a n also control the
c a m e r a lens , the op eration of the
joyst ick and the ke y s a r e inv alid fo r
the c a m e r a un der the general menu .
Then Press【4】to enter the menu of tour, as
LCD shows (picture 4.2.4-1)
1、Tour num:＿
2、Insert preset
3、Run tour
4.2.3 Pattern setting
Enter the menu, as LCD shows (picture 4.1.1-1)
Press 【2】 to enter the dome setting menu, as
LCD shows (Picture 4.2.1-1)
Then Press 【 3】 to enter the pattern setting
menu, as LCD shows (picture 4.2.3-1)
1、Pattern num:＿
2、Set pattern
3、Run pattern
Picture 4.2.3-1
After entering the menu, the system requires y o u
t o input t h e pattern tour that you set in the first
item, the input range is 1-4, press 【Enter】 to
confirm,the cursor will auto-jump to the second
item. To start setting a pattern ( if user has
finished to set pattern already you can jump over this
item) choose 【3】to run pattern directly.
Picture 4.2.4-1
After entering the menu, the system requires y o u
t o input t h e tour that you will set in the first item , the
input range is 1-6, press【Enter】 to confirm, the
cursor will auto-jump to the second row to start tour
setting, if user has finished to set tour already, you
can jump over the second item to run t h e tour
directly, t h e LCD will show ' Success' and back to
the former menu, it means the operation is
successful.
Choose the second item (as picture 4.2.4-2
shows) to input presets that you need to insert in
a tour. Inputting a preset speed in the second item:
Input range i s b e t w e e n 1-127. Input t h e preset
park time in the third item:input range between 1-255
Press 【Enter】 to confirm, LCD will show
Success and w i l l g o back to the former
menu, it means the operation of adding preset is
successful.
1、Preset num:＿
2、speed:
3、dwell:
Pattern setting: after entering the pattern menu,
to move the dome in an appropriate position, press
【1】 to start to record pattern tour. LCD will show
(Start...... ) as picture 4.2.3-2 shows.
Picture 4.2.4-2
Press【3 】 to run tour.
Press (0) to stop recording pattern, LCD will show
( Success) and w i l l g o back to the former menu,
it means the operation w a s successful.
12
NOTICE
I t is vali d to ins ert the preset s in tou r under
theVIDO-B02 pro tocol b ut it is invalid
under o ther protocols.
Keyboard Parameter Setting
4. 3 Protocol setting
4.3.2 Dome controlling mode
Enter the menu, LCD d i s p l a y s a s s h o w n i n
picture 4.1.1-1.
Press 【 3 】 to enter protocol setting, as LCD
shows in picture 4.3-1.
Choose【2】to enter t h e P T Z c a m e r a / dome
direct control mode, as LCD shows in picture
4.3.2-1.
1、Matrix
2、Dome
Picture 4.3-1
4.3.1 Pelco matrix mode
Press【1】to enter PELCO matrix mode
As LCD shows in picture 4.3.1-1)
Press【Enter】to choose protocol and g o back to
the former menu.
1、Pelco matr ix
Picture 4.3.1-1
Choose corresponding protocol according to what
the camera uses, the system will g o back to the
former menu automatically after deciding the
protocol.
1、Factory protocol
2、Pelco-p protocol
3、Pelco-d protocol
4、VIDO-B02
Picture 4.3.2-1
4. 4 Exit to keyboard menu
Enter the menu, as LCD shows in picture
4.2.1-1) Press 【 4 】 to exit the menu
directly.
Appendix
5. 1 RS485 Bus Basic Knowledge
* Problems in practical use
If the user adopts a star configuration d u r i n g
* Characteristic of RS485 Bus line
According to RS485 standards, RS485 Bus
practical connection the termination resistors must be
c o n s i s t s o f half-duplexed data transmission
connected to the two b i t s o f equipment t h a t are
cables with characteristic impedance o f
t h e farthest away from each other, such as
120
Ω. The maximum load capacity is 32 unit
equipment 1# and 15# (refer to picture 4-1.3).
loads (including main controller and controller
Otherwise you may experience signal
equipment)
Transmission distance of RS485 Bus line
*
When user selects the 0.56mm (24AWG) twisted
reflection and loss of signal transmission the
f u r t h e r a w a y t h e e q u i p m e n t a r e . This connection
way not
b e
i n
accord a n c e with the
pair as data transmission cable, the maximum
requirements of RS485 standards in this
theoretical transmitting distances are s h o w n
installation method. I f y o u h a v e t h e
b e l o w according to different baud rate:
equipment too far away you will not be
If user selects thinner cables, or installs the camera
a b l e t o control the dome or continuous l y operate
in an environment with a strong electromagnetic
by itself.
interf erence, or connects lots of equipment to the
The factory will recommend the RS485 distributor. The
RS485 Bus, the maximum transmitting distance
distributor can transfer the star configuration
will be decreased. To increase the maximum
connection to the mode
transmitting distance , do the contrary.
with the RS485 standards. The new connection
of connection accordance
achieves reliable data transmission and avoid s the
Maximum Distance
Baud Rate
2400 bps
1800m
4800 bps
1200m
9600 bps
800m
19200bps
600m
problem. (refer to picture 4-1.4)
120Ω
1#
* Connection and terminal resistance
6#
Mai n Con tr o llo r
The RS485 standards require a daisychain
connec tion betw een the e quipm ent. T here must
be term ination resista nc e with 120
32#
Ωat both
ends of the c onnection (refer to picture 4-1.1).
Please refer to picture 4-1.2 for simple
c onnec tion. And
“ D ”
should not
120Ω
exc eed 7m.
1 20Ω
1#
15#
Picture 4-1.3
2#
3#
4#
12 0Ω
32#
Picture 4-1.1
Rs485 Distributor
A+
B-
120Ω
1#
120Ω
2#
120Ω
3#
A+
D
BA+
1 20Ω
1#
B-
2#
3#
Picture 4-1.2
4#
1 20Ω
32#
Picture 4-1.4
13
Appendix
5. 2 Keyboard shortcut operation manual
Working
Mode
Direct Contr ol
Mode and
PELCO Matr ix
Mode
Shortcut
Operation object
【N】 +【Cam】
High s peed d ome
Input D ome ID, pres s【Ca m】to select object dome .
【Tele】
High s peed d ome
P ress【 Tele】 , incre ase th e mult iple of lens
【Wide】
High s peed d ome
P ress【 Wide】 , reduce the multi ple of lens
【Far】
High s peed d ome
P ress【 Far】 , far fo cus
【Near】
High s peed d ome
P ress【 Near】 , nea r focus
【Close】
High s peed d ome
P ress【 Close 】, red uct the Iris
【Open】
High s peed d ome
P ress【 Open】 , increase th Iris
High s peed d ome
Adjust th e ima ge to o bject p ositio n, press【Se t】to input
pr eset N umbe r, then press 【Pres et】to set preset.
【N】 + 【Preset】
High s peed d ome
I nput p reset N umbe r, pres s【Pr eset】to call the pre set.
【SET】+ 【1】+ 【Scan】
High speed dome
Adjust th e ima ge to o bject p ositio n, press【Se t】to input 1,
th en pre ss【Scan】t o set s can left limit.
【SET】+ 【2】+ 【Scan】
High s peed d ome
Adjust the image to obj ect po sition, press【 Set】 to inp ut 2,
then press 【Sca n】to s et sca n right limit.
【1】+【Scan】
High s peed d ome
Input 1, press 【Sca n】to r un sca n.
【Set】+【N】+【Pattern】
High s peed d ome
P ress【 Set】 to inpu t patte rn num ber, p ress【 Pattern】to
r ecord pattern path.
【Set】+【0】+【Pattern】
High s peed d ome
P ress【 Set】 ,input 0, then press 【Patt ern】t o save patter n
【N】 + 【Pattern】
High s peed d ome
I nput p attern number(1-4), press 【Pat tern】 to run p attern .
【N】 + 【Tour】/【Tour】
High s peed d ome
Input to ur num ber, p ress【 Tour】 or dir ectly press【 Tour】
to run c ruise.
【9】+【5】 + 【Preset】
High speed dome
Input 95 to call main menu of dome
【Shift】+ 【Set】
Ma trix
P ress【 Shift】 and【 Set】 to call main m enu o f matrix
【Prev】
Ma trix
S witch to pre vious d ome. Press【 Prev 】to ju mp the
p reviou s dom e, pre ss【Pr ev】to hold i t for 2s ，con t inuous ly swi tch the sixtee n dom es of connection
m atrix forwar ds.
【Next】
Ma trix
S witch to nex t dome . Pres s【Next】to jump th e nex t dome ,
p ress【 Next】 to hol d it for 2s，continu ously s witch the
s ixteen dome s of co nnecti on ma trix ba ckwards.
【Stop】
Ma trix
S top to switch .
【Enter】
Ma trix
After pro gram, press 【Ent er】 to confir m.
【N】 + 【MON】
Monitor
【Set】+【N】 + 【Preset】
PELCO Matrix
Mo de
14
Function
Input m onitor Numb er, pre ss【C am】to selec t objec t mon itor.
Appendix
6、Keyboard Menu Index
16