EnGenius EP 801 Owner Manual

EP801

Quick Installation Guide

Base station installation

1. Install base station antenna.

2. Plug the transformer end of the base station AC/DC adapter into a standard AC electrical power outlet, plug the other end into the “DC IN” jack on the back of the base station.

3. Plug phone cord into the “LINE” jack.

4. A standard telephone or answering machine can be plugged into the adjacent receptacle on the bottom of the base station marked TEL.

Handset and charger installation (Charger only for EP801 HC)

1. Plug the transformer end of the charger AC/DC adapter into a standard AC electric power outlet, plug the other end into the “DC In” jack on the back of the charger.

2. Install battery pack onto the handset.

3. Install handset antenna.

4. Place handset onto the charger front slot.

5. Fully charge the battery for three hours before use.

6. The phone system is now ready to perform basic functions such as making and receiving phone calls and intercom calls. No base station or handset programming is needed for basic operations.

Handset registration

1. Press MENU-7 to enter the registration mode.

2. Press and hold the base’ registration (REG) button for 2 seconds until and LEDs lighting up and flashing, also the base will emit ringing to remind you the base is in registration mode.

3. Press handset key “1”, this completes the registration process. The base station will assign a handset ID between 12 and 19. The assigned ID will be displayed on the handset LCD, indicating sucessful registration.

Handset features

1. TALK/FLASH a. Places or answers a telephone or intercom call. b. Sends a flash signal to phone line to retrieve a dial tone after the call ends, or to perform the call waiting feature provided by local phone companies during a call.

2. SPEAKERPHONE a. Press the key to enable/disable the speakerphone during incoming, outgoing or intercom call.

3. 2-WAY INTERCOM/TRANSFER a. Places an intercom call to another handset, a group handsets (group paging) or all registred handsets.

b. Intercom calls are digital, full duplex and are conducted without the assistance from the base.

4. BROADCAST a. Half duplex broadcasting to handsets for immediate announcement.

b. Half duplex broadcasting to base stations.

Re-press the key on the side of handsets to activate the broadcast function.

EnGenius Europe | Veldzigt 28, 3454 PW De Meern,

Netherlands | 0900-WIFIABC | www.wifiabc.com

Disclaimer: Information may be subject to changes without prior notification.

Follow us https://www.linkedin.com/company/engeniuseurope https://twitter.com/engeniuseu https://plus.google.com/+EngeniusEuropeBVDeMeern https://www.youtube.com/user/engeniuseuropebv

EP801

Quick Installation Guide

5. LEFT/RIGHT SOFT KEY a. Make menu selection.

6. UP /DOWN SCROLLING KEYS a. Scroll through record and menu selections. b. Adjust receiver voice volume when in Talk-mode. c. Press to adjust ringer volume when in Standby-mode. d. Press to enter phonebook when in Standby-mode.

7. END; On/Off key a. Ends a call. b. Leaves current menu operation, up one level. c. Press for 3 seconds to off the power.

8. CALLER-ID a. Review caller ID list.

b. Including received and missed caller ID.

Base functions

1. RESET button a. Restores base station to factory settings. b. Reset button is indented to prevent accidental system reset. c. All handsets (including administrator) and additional base(s) need to be re-registered after a base station reset.

2. REGISTRATION button (REG)

Enters registration mode along with handset, assigns handset ID (11-19).

3. DIALING-keys a. Enter the phone number after pressing the speakerphone key. b. Enter the handset ID or Group ID when making the intercom call or broadcast. c. Enter the phone number when storing the base speed dial directory.

4. FUNCTION-keys a. TRANSFER : During talk, press the key to transfer the call to a registered handset. b. MEMORY : Store phone number into speed dial memory of base unit. Up to 20 entries. Or retrieve a phone number from the speed dial memory during the talking. c. HOLD : Press the key to put the call on hold. d. FLASH : Press the key to send a flash signal to a phone line to retrieve a dial tone after the call ends, or to perform the call waiting feature provided by local phone companies during a call. e. REDIAL/P : Press the key retrieve the last dialed number. Or store a pause time (1 second) while storing the speed dial memory.

5. VOLUME and

+ a. Increase or decrease the ringer volume during standby mode. b. Increase or decrease the voice volume during talk mode.

6. SPEAKERPHONE key a. Press the key to get a dial tone, followed by a phone number to make an outgoing call. b. Press the key again to hang up to call.

c. When enable the speakerphone, the backlight of the key will be turned on too.

7. INTERCOM/BROADCAST a. Enter handset ID then press the key to enable the 2-way intercom feature. b. Enter handset ID then press and hold the key for over one second to enable the broadcast feature.

Re: Press the key without entering handset ID first, all registered handsets will be enabled.

EnGenius Europe | Veldzigt 28, 3454 PW De Meern,

Netherlands | 0900-WIFIABC | www.wifiabc.com

Disclaimer: Information may be subject to changes without prior notification.

Follow us https://www.linkedin.com/company/engeniuseurope https://twitter.com/engeniuseu https://plus.google.com/+EngeniusEuropeBVDeMeern https://www.youtube.com/user/engeniuseuropebv