advertisement
Operating and installation instructions
Ceramic hobs with induction
To avoid the risk of accidents or damage to the appliance it is essential to read these instructions before it is installed and used for the first time.
en-GB M.-Nr. 09 055 450
Contents
2
Contents
3
Warning and Safety instructions
This hob complies with all relevant safety requirements. Inappropriate use can, however, lead to personal injury and damage to property.
To avoid the risk of accidents and damage to the hob, please read these instructions carefully before installation and before using it for the first time. They contain important notes on installation, safety, use and maintenance.
Miele cannot be held liable for damage caused by non-compliance with these instructions.
Keep these instructions in a safe place and ensure that new users are familiar with the content. Pass them on to any future owner.
4
Warning and Safety instructions
Correct application
This hob is intended for domestic use and use in other similar environments.
This hob is not intended for outdoor use.
It is intended for domestic use only to cook food and keep it warm. Any other use is not supported by the manufacturer and could be dangerous.
People with reduced physical, sensory or mental capabilities, or lack of experience and knowledge who are not able to use the hob safely on their own must be supervised whilst using it. They may only use it unsupervised if they have been shown how to use it safely and recognise and understand the consequences of incorrect operation.
5
Warning and Safety instructions
Safety with children
Children under 8 years of age must be kept away from the hob unless they are constantly supervised.
Children 8 years and older may only use the hob unsupervised if they have been shown how to use it in a safe way and can recognise and understand the consequences of incorrect operation.
Children must not be allowed to clean the hob unsupervised.
Please supervise children in the vicinity of the hob and do not let them play with it.
The hob gets hot when in use and remains hot for a while after being switched off. Keep children well away from the hob until it has cooled down and there is no danger of burning.
Danger of burning.
Do not store anything which might arouse a child's interest in storage areas above or next to the hob. Otherwise they could be tempted into climbing onto the appliance.
Danger of burning or scalding.
Place pots and pans on the cooking zone in such a way that children cannot pull them down and burn themselves.
Danger of suffocation. Packaging, e.g. plastic wrappings, must be kept out of the reach of babies and children. Whilst playing, children could become entangled in packaging or pull it over their head and suffocate.
Activate the system lock to ensure that children cannot switch on the hob inadvertently.
6
Warning and Safety instructions
Technical safety
Unauthorised installation, maintenance and repairs can cause considerable danger for the user. Installation, maintenance and repairs must only be carried out by a Miele authorised technician.
Do not use a damaged appliance. It could be dangerous. Check the hob for visible signs of damage.
Reliable and safe operation of this hob can only be assured if it has been connected to the mains electricity supply.
The electrical safety of this hob can only be guaranteed when correctly earthed. It is essential that this standard safety requirement is met. If in any doubt please have the electrical installation tested by a qualified electrician.
To avoid the risk of damage to the hob, make sure that the connection data on the data plate (voltage and frequency) match the mains electricity supply before connecting it to the mains.
Consult a qualified electrician if in doubt.
Do not connect the hob to the mains electrical supply by a multisocket adapter or extension lead. These are a fire hazard and do not guarantee the required safety of the appliance.
For safety reasons, this hob may only be used after it has been built in.
This hob must not be used in a non-stationary location (e.g. on a ship).
Never open the casing of the hob.
Touching or tampering with electrical connections or components and mechanical parts is highly dangerous to the user and can cause operational faults.
While the hob is under guarantee, repairs should only be undertaken by a Miele authorised service technician. Otherwise the guarantee is invalidated.
7
Warning and Safety instructions
Miele can only guarantee the safety of the appliance when genuine original Miele replacement parts are used. Faulty components must only be replaced by Miele spare parts.
The hob is not intended for use with an external timer switch or a remote control system.
If the plug is removed from the connection cable or if the cable is supplied without a plug, the appliance must be connected to the electrical supply by a suitably qualified electrician.
If the connection cable is damaged, it must be replaced by a suitably qualified electrician with a special connection cable of type H
05 VV-F (pvc insulated). See "Electrical connection".
The hob must be disconnected from the mains electricity supply during installation, maintenance and repair work. Ensure that power is not supplied to the appliance until after it has been installed or until any maintenance or repair work has been carried out.
Danger of electric shock.
Do not use the hob if it is faulty, or if the ceramic surface is cracked, chipped or damaged in any way. Switch it off immediately, disconnect it from the mains electricity supply and contact Miele.
If the hob is installed behind a furniture panel (e.g. a door), ensure that the door is never closed whilst the hob is in use. Heat and moisture can build up behind a closed furniture panel and cause subsequent damage to the hob, the housing unit and the floor. Do not close the door until the residual heat indicators have gone out.
8
Warning and Safety instructions
Correct use
The hob gets hot when in use and remains hot for a while after being switched off. There is a danger of burning until the residual heat indicators go out.
Oil and fat can overheat and catch fire. Do not leave the hob unattended when cooking with oil and fat. If it does ignite do not attempt to put the flames out with water.
Disconnect the hob from the mains and use a suitable fire blanket, saucepan lid, damp towel or similar to smother the flames.
Flames could set the grease filters of a cooker hood on fire. Do not flambé under a cooker hood.
Spray canisters, aerosols and other inflammable substances can ignite when heated. Therefore do not store such items or substances in a drawer under the hob. Cutlery inserts must be heat-resistant.
Do not heat an empty pan.
Do not heat up food in closed containers e.g. tins or sealed jars on the hob, as pressure can build up in the container, causing it to explode.
Do not cover the hob, e.g. with a hob cover, a cloth or protective foil. The material could catch fire, shatter or melt if the hob is switched on by mistake or if residual heat is still present.
When the appliance is switched on either deliberately or by mistake, or when there is residual heat present, there is the risk of any metal items left on the hob heating up, with the danger of burning.
Depending on the material, other items left on the hob could also melt or catch fire. Damp pan lids might adhere to the ceramic surface and be difficult to dislodge. Do not use the appliance as a resting place. Switch the cooking zones off after use.
9
Warning and Safety instructions
You could burn yourself on the hot hob. Protect your hands with heat-resistant pot holders or gloves when handling hot pots and pans. Do not let them get wet or damp, as this causes heat to transfer through the material more quickly with the risk of scalding or burning yourself.
When using an electrical appliance, e.g. a hand-held food blender, near the hob, ensure that the cable of the electrical appliance cannot come into contact with the hot hob. The insulation on the cable could become damaged.
Grains of salt, sugar and sand (e.g. from cleaning vegetables) can cause scratches if they get under pan bases. Make sure that the ceramic surface is clean before placing pans on it.
Even a light object can cause damage in certain circumstances.
Do not drop anything on the ceramic surface.
Do not place hot pans on the display as this could cause damage to the electronics underneath. Do not place hot pans on the area around the display.
Do not allow solid or liquid sugar, or pieces of plastic or aluminium foil to get onto the cooking zones when they are hot, as they can damage the ceramic surface when it cools down. If this should occur, switch off the appliance and scrape off all the sugar, plastic or aluminium residues whilst still hot, using a shielded scraper blade.
Wear oven gloves. Allow the cooking zones to cool down and clean them with a suitable ceramic hob cleaning agent.
Pans which boil dry can cause damage to the ceramic glass. Do not leave the hob unattended whilst it is being used.
Only use pots and pans with smooth bases. Rough bases will scratch the ceramic glass.
Lift pans into position on the hob. Sliding them into place can cause scuffs and scratches.
10
Warning and Safety instructions
Induction heating works extremely quickly and so the base of the pan could heat up to the temperature at which oil or fat self-ignites within a very short time. Do not leave the hob unattended whilst it is being used.
Heat oil or fat for a maximum of one minute. Do not use the
Booster function to heat oil or fat.
For people fitted with a heart pacemaker: Please note that the area immediately surrounding the hob is electromagnetically charged. It is very unlikely to affect a pacemaker. However, if in any doubt, consult the manufacturer of the pacemaker or your doctor.
To prevent damage to items which are susceptible to electromagnetic fields, e.g. credit cards, digital storage devices, pocket calculators, etc, do not leave them in the immediate vicinity of the hob.
Metal utensils stored in a drawer under the hob can become hot if the appliance is used intensively for a long time. Do not store any metal items or utensils in a drawer under the hob.
This hob is fitted with a cooling fan. If a drawer is fitted directly underneath the hob, ensure that there is sufficient space between the drawer and its contents and the underside of the appliance in order to ensure sufficient ventilation of the hob. Do not store pointed or small items or paper in the drawer. They could get in through the ventilation slots or be sucked into the housing by the fan and damage the fan or impair cooling.
Do not use two pans on a cooking zone or extended zone at the same time.
If the pan only partially covers the cooking zone, the handle could become very hot.
Ensure that you always place the pan in the middle of the cooking zone.
11
Warning and Safety instructions
Where several CombiSets are installed side by side:
Hot objects can damage the seal of the cover strip between the appliances. Do not place hot pans near or on the cover strip.
12
Warning and Safety instructions
Cleaning and care
Do not use a steam cleaning appliance to clean this hob.
The steam could reach electrical components and cause a short circuit.
If the hob is built in over a pyrolitic oven, the hob should not be used whilst the pyrolitic process is being carried out, as this could trigger the overheating protection mechanism on the hob (see relevant section).
13
Caring for the environment
Disposal of the packing material
The packaging is designed to protect the appliance from damage during transportation. The packaging materials used are selected from materials which are environmentally friendly for disposal and should be recycled.
Recycling the packaging reduces the use of raw materials in the manufacturing process and also reduces the amount of waste in landfill sites.
Disposing of your old appliance
Electrical and electronic appliances often contain valuable materials. They also contain specific materials, compounds and components, which were essential for their correct function and safety. These could be hazardous to human health and to the environment if disposed of with your domestic waste or if handled incorrectly. Please do not, therefore, dispose of your old appliance with your household waste.
Please dispose of it at your local community waste collection / recycling centre for electrical and electronic appliances, or contact your dealer or
Miele for advice. You are also responsible (by law, depending on country) for deleting any personal data that may be stored on the appliance being disposed of. Please ensure that your old appliance poses no risk to children while being stored prior to disposal.
14
Hob
CS 1212-1
Guide to the appliance a Cooking zone with TwinBooster b Cooking zone with Booster c Cooking zone display d Cooking zone symbols e Indicators f Control for the rear cooking zone g Control for the front cooking zone
15
Guide to the appliance
CS 1221-1 a Cooking zone with TwinBooster b Cooking zone display c Indicators d Cooking zone controls
16
CS 1222
Guide to the appliance a Extended zone with TwinBooster b Cooking zone with Booster c Cooking zone display d Cooking zone symbols e Indicators g Control for the front cooking zone h Control for the rear cooking zone
Indicators
B
l In-operation indicator m Booster indicator n Residual heat indicator
17
Guide to the appliance
Control symbols
Symbol
0
1 – 9
B I
B I/II
Description
Cooking zone off
Keeping warm setting
Power levels
Booster level 1
TwinBooster with 2 levels
Display
Symbol
/
Description
No pan on cooking zone or pan unsuitable (see "Induction")
Auto heat-up activated
Booster / TwinBooster level 1 activated
TwinBooster level 2 activated
The system lock has been activated
Safety switch-off (see "Safety features")
Overheating protection (see "Safety features")
Cooking zones
Cooking zone
Ø in cm*
10–16
16–23
CS 1212-1
Rating in watts for 230 V**
Normal
Booster
Normal
TwinBooster, level 1
TwinBooster, level 2
Total
1400
2200
2300
3000
3700
3700
* Pans with a base diameter within the given range may be used.
** The wattage quoted may vary depending on the size and material of the pans used.
18
Guide to the appliance
Ø in cm*
18–28
CS 1221-1
Rating in watts for 230 V**
Normal
TwinBooster, level 1
TwinBooster, level 2
2600
3000
3700
* Pans with a base diameter within the given range may be used.
** The wattage quoted may vary depending on the size and material of the pans used.
Cooking zone
Ø in cm*
10–16
14–20
CS 1222
Rating in watts for 230 V**
Normal
Booster
Normal
TwinBooster, level 1
TwinBooster, level 2
1400
2200
1850
2500
3000
20 x 30 Normal
TwinBooster, level 1
TwinBooster, level 2
Total
* Pans with a base diameter within the given range may be used.
** The wattage quoted may vary depending on the size and material of the pans used.
2300
3000
3700
3700
19
Using for the first time
Please stick the extra data plate for the appliance supplied with this documentation in the space provided in the "After sales service, data plate, guarantee" section of this booklet.
Remove any protective wrapping and stickers.
Cleaning the hob for the first time
Before using for the first time, clean the hob with a damp cloth only and then wipe dry.
Switching on the hob for the first time
When the hob is first connected, or after an interruption to the power supply, all of the indicators in the display will light up for approx. 1 second for testing. As soon as they go out, the hob is ready for use.
The metal components have a protective coating which may give off a slight smell when heated up for the first time.
The induction coils may also give off a slight smell for the first few hours of operation. This smell will be less noticeable with each subsequent use before dissipating completely.
The smell and any vapours given off do not indicate a faulty connection or appliance and they are not hazardous to health.
Please note that the heating up time on induction hobs is very much shorter than on conventional hobs.
20
The induction principle
An induction coil is located under each cooking zone. When a cooking zone is switched on, this coil creates a magnetic field which impacts directly on the base of the pan and heats it up. The cooking zone itself is heated up indirectly by the heat given off by the pan.
An induction cooking zone only works when a ferromagnetic pan is placed on it (see "Pans"). The induction cooking zone automatically recognises the size of the pan.
will appear in the cooking zone display,
– if the zone has been switched on without a pan in place, or if the pan is unsuitable (non-magnetic base),
– if the diameter of the base of the pan is too small,
– if the pan is taken off the cooking zone when it is switched on.
If a suitable pan is placed on the cooking zone within 3 minutes, the will go out and you can continue as normal.
If no pan or an unsuitable pan is placed on the cooking zone, the cooking zone will switch off automatically after 3 minutes. and will flash alternately in the cooking zone display.
Induction
When the appliance is switched on either deliberately or by mistake, or when there is residual heat present, there is the risk of any metal items placed on the hob (e.g. cutlery) heating up.
Danger of burning.
Do not use the hob as a resting place for items. Switch the cooking zones off after use by turning the control to "0".
21
Induction
Noises
When using an induction cooking zone, the following noises can occur in the pan, depending on what it is made of and how it has been constructed.
On the higher power settings, it might buzz. This will decrease or cease altogether when the power setting is reduced.
If the pan base is made of layers of different materials (e.g. in a sandwiched base), it might emit a cracking sound.
Whistling might occur if linked zones
(see "Booster") are being used at the same time, and the pans also have bases made of layers of different materials.
You might hear a clicking sound from the electronic switches, especially on lower power settings.
You might hear a whirring sound when the cooling fan switches on. It switches on to protect the electronics when the hob is being used intensively. The fan may continue to run after the appliance has been switched off.
22
Induction
Pans
The following pan types are suitable:
– stainless steel with a base that can be magnetised,
– enamelled steel,
– cast iron.
The following pan types are not suitable:
– stainless steel pans without a magnetic base,
– aluminium and copper pans,
– glass, ceramic or earthenware pots and pans.
To test whether a pot or pan is suitable for use on an induction hob, hold a magnet to the base of the pan. If the magnet sticks, the pan is suitable.
If an unsuitable pan is used, the symbol will appear in the cooking zone display.
The composition of the pan base can affect the evenness of the cooking results (e.g. when making pancakes).
– To make optimum use of the cooking zones, choose a pan with a suitable base diameter (see "Guide to the appliance - Cooking zones"). If the pan is too small, it will not be recognised and the symbol will appear in the cooking zone display.
– Only use pots and pans with smooth bases. Rough bases will scratch the ceramic glass.
– Lift pans into position on the hob.
Sliding them into place can cause scuffs and scratches.
– Often the maximum diameter quoted by manufacturers refers to the diameter of the top rim of the pot or pan. The diameter of the base (generally smaller) is the more important one.
23
Tips on saving energy
– Use a lid whenever possible to minimise heat loss.
– Select a smaller pan when cooking small quantities. A smaller pan uses less energy than a larger pan with very little in it.
– Cook with as little water as possible.
– Once food has come to the boil or the oil in the pan is hot enough for frying, reduce the heat to a lower setting.
– Use a pressure cooker to reduce cooking times.
24
Settings
Keeping warm
Melting butter
Dissolving gelatine
Melting chocolate
Making milk puddings
Warming small quantities of liquid
Cooking rice
Defrosting frozen vegetables
Making porridge
Warming liquid and semi-solid food
Making omelettes or lightly frying eggs
Steaming fruit
Cooking dumplings
Steaming vegetables and fish
Defrosting and reheating frozen food
Gently frying eggs (without overheating the fat)
Bringing large quantities of food to the boil, e.g. casseroles.
Thickening custard and sauces, e.g. hollandaise
Gently frying meat, fish and sausages (without overheating the fat)
Frying pancakes, potato fritters etc.
Braising meat
Boiling large quantities of water
Bringing to the boil
Setting range
1-2
2
3
3
3
4
4
5
5
6
6-7
6-7
7
8
9
These settings should only be taken as a guide. The power of the induction coils will vary depending on the size and material of the pan. For this reason, it is possible that the settings will need to be adjusted slightly to suit your pans. As you use the hob, you will get to know which settings suit your pans best. When using new pans that you are not familiar with, set the power level below the one specified.
25
Operation
Cooking zone controls
The cooking zone controls must not be turned past B I or B I/II to 0.
Switching on
Fire hazard.
Do not leave the hob unattended whilst it is being used.
Please note that the heating up time on an induction hob is very much shorter than on a conventional hob.
Turn the cooking zone control clockwise to the setting you want.
The in-operation indicator will light up.
The residual heat indicator will light up after a certain temperature has been reached.
Switching off
Turn the cooking zone control anticlockwise to 0.
When all cooking zones are switched off the in-operation indicator will go out.
Residual heat indicator
If a cooking zone is hot, the residual heat indicator will light up when it has been switched off. The residual heat indicator will only go out when the cooking zone is safe to touch.
Danger of burning. Do not touch the cooking zones whilst the residual heat indicators are lit up.
26
Auto heat-up
When Auto heat-up has been activated, the cooking zone switches on automatically at the highest power setting and then switches to the continued cooking setting. The heat-up time depends on which continued cooking setting has been chosen (see chart).
Activating
Turn the cooking zone control anticlockwise and hold until appears in the cooking zone display.
Now turn the cooking zone control clockwise to the continued cooking setting you want.
The continued cooking level must be set within 5 seconds of activating Auto heat-up.
You can change the continued cooking level up to approx. 10 seconds after activating Auto heat-up.
If you hold down the cooking zone control for too long the system lock will be activated and will appear in the cooking zone display.
lights up in the cooking zone display during the heat-up time (see chart).
Deactivating
Select a different power level.
Operation
Continued cooking setting
1
4
5
2
3
8
9
6
7
Heat-up time
[min : sec] approx. 0 : 15 approx. 0 : 15 approx. 0 : 25 approx. 0 : 50 approx. 2 : 00 approx. 5 : 50 approx. 2 : 50 approx. 2 : 50
–
27
Operation
Booster
The cooking zones are equipped with a
Booster with one level or a TwinBooster with two levels (see "Guide to the appliance - Hob").
When activated, the power is boosted for a maximum of 10 minutes so that large quantities can be heated quickly, e.g. when boiling water for cooking pasta. The cooking zone will automatically revert to power level 9 at the end of the Booster duration.
Hobs with 2 cooking zones: the booster function cannot be used on both cooking zones at the same time.
Hobs with 4 cooking zones: the booster function can only be used on a maximum of two cooking zones at the same time.
Cooking zones are linked in pairs to supply the power for the booster function.
When the booster function is selected, a proportion of energy is taken away from the linked cooking zone and the following happens within the pairs:
– Auto heat-up is deactivated
– the power level is reduced
– the linked cooking zone is switched off.
If the power level is reduced, the reduced power level and will flash alternately in the cooking zone display.
If the linked cooking zone is switched off, and will flash alternately in the cooking zone display.
28
Operation
To switch on the Booster
Turn the cooking zone control clockwise past 9 to B I and back again to 9.
will appear in the cooking zone display, the "B" Booster indicator will light up.
To switch on the TwinBooster, level 1
Turn the cooking zone control clockwise past 9 to B I/II and back again to 9.
will appear in the cooking zone display, the "B" Booster indicator will light up.
To switch on the TwinBooster, level 2
Turn the cooking zone control clockwise past 9 to B I/II and back again to 9.
will appear in the cooking zone display, the "B" Booster indicator will light up.
Turn the cooking zone control once more clockwise past 9 to B I/II and back again to 9.
will appear in the cooking zone display.
To switch off the Booster / Twin-
Booster
Select a different power level.
The Booster symbol and "B" will go out.
29
Operation
Keeping warm
The keeping warm function is for keeping food that has just been cooked warm, i.e. food that is still hot.
It is not for reheating food that has gone cold.
If the keeping warm function has been activated, the cooking zone will switch off automatically after a maximum of 2 hours.
– Keep food warm in the pan it was cooked in and cover with a lid.
– You do not have to stir food while it is being kept warm.
– Nutrients are lost when food is cooked, and continue to diminish when food is kept warm. The longer food is kept warm for, the greater the loss of nutrients. Try to ensure that food is kept warm for as short a time as possible.
Setting the keeping warm function
Turn the control clockwise to .
30
Safety features
System lock
The system lock can only be activated if all the cooking zones are switched off.
Your hob is equipped with a system lock to prevent the cooking zones being switched on inadvertently.
If a power level is selected when the system lock is activated, appears in the display for approx. 3 seconds.
Activating
Turn the (outer) right cooking zone control anti-clockwise to the point of resistance and hold it until appears in the display.
Deactivating
Turn the (outer) right cooking zone control anti-clockwise to the point of resistance and hold it until goes out in the display.
Safety switch-off
The safety switch-off mechanism is triggered automatically if one of the cooking zones is heated for an unusually long period of time. This period of time depends on the power level selected. Once exceeded, the cooking zone switches off and and flash alternately in the cooking zone display. The cooking zone can be operated again after it has been switched off and back on.
31
Safety features
Overheating protection
All the induction coils and cooling elements for the electronics are fitted with an overheating protection mechanism.
Before the induction coils or cooling elements get too hot, the overheating protection mechanism cuts in in one of the following ways:
– Any Booster function in operation will be switched off.
– The set power level will be reduced.
– The cooking zone will switch off automatically. will flash in the cooking zone display.
– Further cooking zones switch off automatically.
Switch off the affected cooking zone.
If the cooking zone is not switched off,
and will flash alternately in the cooking zone display.
You can use the cooking zones again as usual when the fault code has gone out.
The overheating protection mechanism can be triggered by:
– heating up an empty pan.
– fat or oil being heated on a high power level.
– insufficient ventilation to the underside of the hob.
– a hot cooking zone being switched on after an interruption to the power supply.
If, despite removing the cause, the overheating protection mechanism triggers again, contact Miele.
32
Cleaning and care
Danger of burning.
The cooking zones must be switched off. The hob must have cooled down.
Danger of injury.
The steam from a steam cleaning appliance could reach electrical components and cause a short circuit.
Do not use a steam cleaner to clean the hob.
The use of unsuitable cleaning agents can cause the surfaces to discolour or alter.
All surfaces are susceptible to scratching.
Remove any cleaning agent residues immediately.
Allow the CombiSet to cool down before cleaning.
The CombiSet and accessories should be cleaned after each use.
Dry the CombiSet after using water to clean it. This helps prevent limescale deposits.
Unsuitable cleaning agents
To avoid damaging the surfaces of your appliance, do not use:
– washing-up liquid,
– cleaning agents containing soda, alkalines, ammonia, acids or chlorides,
– cleaning agents containing descaling agents,
– stain or rust removers,
– abrasive cleaning agents, e.g.
powder cleaners and cream cleaners,
– solvent-based cleaning agents,
– dishwasher cleaner,
– grill and oven cleaners,
– glass cleaning agents,
– hard, abrasive brushes or sponges, e.g. pot scourers, or sponges which have been previously used with abrasive cleaning agents,
– melamine eraser blocks.
33
Cleaning and care
Ceramic surface
Do not clean the area between the glass-ceramic surface and the frame or the frame and the worktop with sharp, pointed objects.
This could damage to the seals.
Danger of burning.
Protect your hands with oven gloves before using a shielded scraper blade to remove sugar, plastic or aluminium residues from the hot hob.
Do not use washing-up liquid to clean the appliance as washing-up liquid will not remove all soiling and deposits.
It will form an invisible coating which will cause permanent discolouration of the ceramic surface.
Clean the hob regularly with a suitable ceramic hob cleaning agent.
Wipe all coarse soiling off using a damp cloth. Stubborn soiling may need to be removed with a shielded scraper blade.
Then clean the hob with Miele ceramic and stainless steel hob cleaner (see
"Optional accessories") or a suitable proprietary ceramic hob cleaning agent applied with kitchen paper or a clean cloth. Do not apply cleaner whilst the hob is still hot, as this could result in marking. Please follow the manufacturer's instructions.
Finally wipe the hob with a damp cloth, then dry with a soft, dry cloth. Residues can burn onto the appliance the next time it is used and cause damage to the ceramic surface. Ensure that all cleaning agent residues are removed.
Spots caused by limescale, water and aluminium residues (spots with a metallic appearance) can be removed using
Miele's ceramic and stainless steel hob cleaner.
Should any sugar, plastic or aluminium foil spill or fall onto a hot cooking zone while it is in use, first switch off the appliance. Then carefully scrape off all the sugar, plastic or aluminium residues from the hob immediately whilst they are still hot, using a shielded scraper blade. Allow the appliance to cool down, and then clean as described above.
34
Stainless steel frame/control panel
Clean the frame and the control panel with a solution of warm water and a little washing-up liquid applied with a soft sponge.
You can also use a ceramic and stainless steel cleaning agent. We recommend also using a stainless steel conditioning agent to help prevent resoiling
(see "Optional accessories).
Do not use ceramic and stainless steel cleaner or stainless steel conditioning agent on the printing.
This would rub the printing off.
These areas should be only cleaned with a solution of warm water and a little washing-up liquid applied with a soft sponge.
Operating controls
Clean the control(s) with a solution of warm water and a little washing-up liquid applied with a soft sponge.
Stubborn soiling should be soaked first.
Dry the control(s) with a clean cloth.
Cleaning and care
35
What to do if ...
With the aid of the following guide, minor problems can be easily corrected without contacting Miele.
If having followed the suggestions below, you still cannot resolve the problem, please contact Miele (see end of this booklet for contact details).
Danger of injury. Installation, maintenance and repairs may only be carried out by a suitably qualified and competent person.
Repairs and other work by unqualified persons could be dangerous. Miele cannot be held liable for unauthorised work.
Do not attempt to open the casing of the CombiSet yourself.
Problem
The cooking zones do not heat up.
A smell and vapours are given off when the new appliance is being used.
is flashing in a cooking zone display.
Cause and remedy
There is no power to the hob.
Check if the mains fuse has tripped. If it has, contact a qualified electrician or Miele (minimum fuse rating - see data plate).
There may be a technical fault.
Turn the cooking zone control to 0.
Disconnect the appliance from the electricity supply for approx. 1 minute. To do this:
– switch off at the isolator, or
– disconnect the mains fuse.
If, after resetting the trip switch in the mains fuse box and switching the appliance back on, the appliance will still not heat up, contact a qualified electrician or Miele.
The metal components have a protective coating.
When the appliance is used for the first time, this causes a smell and possibly also vapour. The material from which the induction coils are made also gives off a smell in the first few hours of operation. This smell will be less noticeable with each subsequent use before dissipating completely. The smell and any vapour given off do not indicate a faulty connection or appliance and they are not hazardous to health.
There is no pan on the cooking zone, or the pan is unsuitable.
Use a suitable pan (see "Pans").
36
What to do if ...
Problem
flashes alternately with the power level in a cooking zone display.
Cause and remedy
The power level set has been reduced because the
Booster function on the linked cooking zone has been activated (see "Booster").
flashes alternately with in a cooking zone display. The cooking zone has switched off automatically.
There has been no pan, or an unsuitable pan, on the cooking zone for more than 3 minutes.
Use pans that are suitable for induction (see
"Pans") or switch off the cooking zone if it is no longer needed.
The overheating protection mechanism has been activated.
See "Overheating protection".
appears in the cooking zone display.
TwinBooster level II has been activated on the linked cooking zone.
The overheating protection mechanism has been activated.
See "Overheating protection".
The system lock has been activated.
You need to deactivate the system lock (see "System lock").
appears in the display for several seconds after a cooking zone has been switched on.
appears in the display for several seconds after a cooking zone has been switched on.
The cooking zone does not heat up.
Demonstration mode is activated.
Turn the right-hand (outer) cooking zone control twice briefly anti-clockwise to the point of resistance then once again, holding it for approx.
3 seconds.
37
Optional accessories
Miele offer a comprehensive range of useful accessories as well as cleaning and conditioning products for your
Miele appliances.
These products can be ordered through the Miele Webshop.
These can also be ordered from Miele
(see end of this booklet for contact details) or from your Miele dealer.
Ceramic and stainless steel hob cleaner 250 ml
Removes heavy soiling, limescale deposits and aluminium residues
Stainless steel conditioning agent 250 ml
Removes water marks, flecks and finger prints. Helps keep the appliance looking good for longer.
Microfibre cloth
Removes finger marks and light soiling
38
Safety instructions for installation
The CombiSet must only be installed and connected to the electricity supply by a suitably qualified and competent person in strict accordance with current national and local safety regulations.
Fit the wall units and cooker hood before fitting the CombiSet to avoid damaging it.
The veneer or laminate coatings of worktops (or adjacent kitchen units) must be treated with 100 °C heat-resistant adhesive which will not dissolve or distort. Any backmoulds must be of heat-resistant material.
The CombiSet must not be installed over a fridge, fridge-freezer, freezer, dishwasher, washing machine, washer-dryer or tumble dryer.
This CombiSet must not be installed above an oven unless it has a built-in cooling fan.
The electrical cable of the CombiSet must not come into contact with any moving kitchen component (e.g. a drawer) or be subject to any mechanical action which could damage it.
Observe carefully the safety clearances listed on the following pages.
All dimensions are given in mm.
39
Safety distances
Safety distance above the
CombiSet
A minimum safety distance must be maintained between the CombiSet and the cooker hood above it. See the cooker hood manufacturer's operating and installation instructions for details.
If the manufacturer's instructions are not available for the cooker hood a minimum safety distance of at least
760 mm must be maintained, or if any flammable objects (e.g. utensil rails, wall units etc) are installed above the
CombiSet, a minimum safety distance of at least 760 mm must be maintained between them and the CombiSet below.
When two or more CombiSets which have different safety distances are installed together below a cooker hood, you should observe the greatest safety distance.
40
Safety distances
Safety distances to the sides and back of the hob
The CombiSet may be installed with a wall at the rear and a tall unit or wall to one side (right or left) (see illustrations).
Minimum distance between the back of the worktop cut-out and the rear edge of the worktop:
50 mm
Minimum distance between the worktop cut-out and a tall unit or wall to the right or left of it:
40 mm
50 mm
CS 1212 / CS 1212-1
CS 1221 / CS 1221-1
CS 1234 / CS 1234-1
CS 1223
CS 1222
CS 1112
CS 1122
CS 1134
CS 1326
CS 1327
CS 1411
100 mm CS 1012 / CS 1012-1
150 mm CS 1421
CS 1312
CS 1322
200 mm CS 1034 / CS 1034-1
250 mm CS 1011 / CS 1021
Not allowed
Recommended
Not recommended
Not recommended
41
Safety distances
Minimum safety distances underneath the hob
To ensure sufficient ventilation to the hob, a certain gap must be left between the underside of the hob and any oven, interim shelf or drawer.
The minimum gap between the underside of the hob and
– the top of an oven is 15 mm.
– the top of an interim shelf is 15 mm.
– the base of a drawer is 75 mm.
Interim shelf
It is not necessary to fit an interim shelf underneath the hob but one may be fitted if you wish.
Leave a gap of 10 mm at the back of the shelf to accommodate the cable.
We recommend a gap at the front of the shelf of 20 mm to ensure good ventilation.
42
Safety distances
Safety distance when installing the appliance near a wall with additional niche cladding
A minimum safety distance must be maintained between the worktop cut-out and any niche cladding to protect it from heat damage.
If the niche cladding is made from a combustible material (e.g. wood) a minimum safety distance of 50 mm must be maintained between the cut-out and the cladding.
If the niche cladding is made from a non-combustible material (e.g. metal, natural stone, ceramic tiles) the minimum safety distance between the cut-out and the cladding will be 50 mm less the thickness of the cladding.
Example: 15 mm niche cladding
50 mm - 15 mm = minimum safety distance of 35 mm a Masonry b Niche cladding dimension x = thickness of the niche cladding material c Worktop d Worktop cut-out e Minimum distance to combustible materials 50 mm non-combustible materials 50 mm - dimension x
43
Installation notes
Seal between the CombiSet and the worktop
Tiled worktop
Do not use sealant between the
CombiSet and the worktop. This could result in damage to the
CombiSet or the worktop if the
CombiSet ever needs to be removed for servicing.
The sealing strip under the edge of the top part of the appliance provides a sufficient seal for the worktop.
Grout lines and the hatched area underneath the CombiSet frame must be smooth and even. If they are not the
CombiSet will not sit flush with the worktop and the sealing strip underneath the top part of the appliance will not provide a good seal between the appliance and the worktop.
44
CS 1212-1
Building-in dimensions a Spring clamps b Front c Casing depth d Casing depth including mains connection box with mains connection cable, L =
2000 mm
45
Building-in dimensions
CS 1221-1 / CS 1222 a Spring clamps b Front c Casing depth d Casing depth including mains connection box with mains connection cable, L =
2000 mm
46
Example: 3 CombiSets
Building-in several CombiSets a Spring clamps b Spacer bars c Gaps between spacer bars and worktop d Cover strips e CombiSet width minus 8 mm f CombiSet width g CombiSet width minus 8 mm h Worktop cut-out
47
Building-in several CombiSets
Calculating the worktop cut-out
The frames of the CombiSets overlap the worktop at the outside right and left by
8 mm on each side.
Add up the widths of the CombiSets and subtract 16 mm from this figure.
Example:
288 mm + 288 mm + 380 mm = 956 mm - 16 mm = 940 mm
The CombiSets are 288 mm, 380 mm or 576 mm wide depending on model (see
"Building-in dimensions").
Spacer bars
When building-in several CombiSets a spacer bar must be fitted between each
CombiSet. The position for securing the spacer bar will depend on the width of the
CombiSet.
Installation with a downdraft extractor
Please refer to the separate "Downdraft extractor with CombiSet" instruction manual for details about worktop cut-out dimensions and fitting spacer bars.
48
Installation
Preparing the worktop
Make the worktop cut-out as shown in "Building-in dimensions" or as calculated (see Building-in several
CombiSets). Observe the safety distances (see "Safety distances").
Wooden worktops
Seal the cut surfaces with a suitable sealant to avoid swelling caused by moisture. The sealant must be heatresistant.
Make sure that the sealant does not come into contact with the top of the worktop.
Position the spring clamps and spacer bars on or at the top edge of the cut-out in the positions shown.
Secure the spring clamps and spacer bars with the 3.5 x 25 mm wood screws supplied.
49
Installation
Natural stone worktops
You will need heavy duty double-side tape (not supplied) to secure the spring clamps and spacer bars.
Stick the tape to the top edge of the cut-out in the positions shown in the diagram.
Position the spring clamps and spacer bars on or at the top edge of the cut-out and press them firmly into place.
Apply silicone to the side and lower edges of the spring clamps and the spacer bars .
Then fill gap between spacer bar and the worktop with silicone.
50
Installation
Installation with a downdraft extractor
Please refer to the separate "Downdraft extractor with CombiSet" instruction manual for details about installing a downdraft extractor with a CombiSet appliance.
Installing the CombiSet
Feed the mains connection cable down through the cut-out.
Starting at the front, position the
CombiSet in the worktop cut-out.
Using both hands, press down evenly on the edges of the CombiSet until it clicks into position. When doing this make sure that the seal underneath the appliance sits flush with the worktop. This is important to ensure an effective seal with the worktop.
Do not use sealant (e.g. silicone).
Building in several CombiSets
Push the built-in CombiSet to the side until the holes in the spacer bar can be seen.
Fit cover strip into the holes in spacer bar .
Starting at the front, position the next
CombiSet in the worktop cut-out.
Proceed as described previously.
If the seal does not meet the worktop correctly on the corners, the corner radius (≤ R4) can be carefully scribed to suit.
51
Installation
Connecting the CombiSet
Connect the CombiSet(s) to the mains.
Check that each CombiSet works.
Removing the CombiSet
If the CombiSet cannot be accessed from below, you will need a special tool to remove it.
If the CombiSet can be accessed from below, push it out from below.
Push the rear side out first.
52
Electrical connection
All electrical work should be carried out by a suitably qualified and competent person in strict accordance with current local and national safety regulations
(e.g. BS 7671 in the UK). Connection should be made via a switched socket.
This will make it easier for service technicians should the appliance need to be repaired. The electrical socket must be easily accessible after installation.
Danger of injury.
Miele cannot be held liable for unauthorised installation, maintenance and repair work as this can be dangerous to users.
Miele cannot be held liable for damage or injury caused by incorrect installation, maintenance or repair work, or by an inadequate or faulty earthing system (e.g. electric shock).
If the plug is removed from the connection cable or if the cable is supplied without a plug, the appliance must be connected to the electrical supply by a suitably qualified electrician.
If the switched socket is not accessible after installation, or if the appliance is to be hard-wired, an additional means of disconnection must be provided for all poles. When switched off, there must be an allpole contact gap of at least 3 mm in the switch (including switch, fuses and relays). Connection data is shown on the data plate. It must match the mains electrical supply.
After installation ensure that all electrical components are shielded and cannot be accessed by users.
Total power rating
See data plate
Connection
AC 230 V, 50 Hz
The connection data is quoted on the dataplate. It must match the household supply.
Residual current device
For extra safety, it is advisable to protect the CombiSet with a suitable residual current device (RCD) with a trip range of 30 mA.
53
Electrical connection
Disconnecting from the mains
Danger of electric shock.
After disconnection, ensure the appliance cannot be switched back on by mistake.
Replacing the mains cable
Danger of electric shock.
The mains connection cable must be replaced by a suitably qualified and competent person in accordance with current local and national safety regulations. (e.g. BS 7671 in the UK).
To disconnect the appliance from the mains power supply, do one of the following depending on installation:
Safety fuses
Completely remove fuses
Automatic circuit breakers
Press the (red) button until the middle
(black) button springs out.
Built-in circuit breakers
Circuit breakers, type B or C: switch the on-off switch from 1 (on) to 0 (off).
Residual current device (RCD)
Switch the main switch from 1 (on) to
0 (off) or press the test button.
If the mains cable needs to be replaced it must be replaced with a special connection cable, type H 05 VV-F (PVC-insulated), available from Miele.
The connection data is quoted on the data plate.
54
After sales service, data plate, guarantee
After sales service
In the event of any faults which you cannot easily remedy, please contact
– your Miele Dealer, or
– Miele Service.
See end of this booklet for contact details.
Please note that telephone calls may be monitored and recorded for training purposes.
N.B. A call-out charge will be applied to service visits where the problem could have been resolved as described in these instructions.
When contacting your Dealer or Miele, please quote the model and serial number of your appliance.
Data plate
Space in which to stick the extra data plate supplied with the appliance. Ensure that the model number is the same as the one on the back page of these instructions.
Guarantee: UK
The appliance is guaranteed for 2 years from the date of purchase.
In the UK, you must activate your cover by calling 0330 160 6640 or registering online at www.miele.co.uk.
Guarantee: Other countries
For information on the appliance guarantee specific to your country please contact
Miele. See end of this booklet for contact details.
55
Product data sheets
The following data sheets apply to the models described in this operating instruction manual.
Information for domestic electric hobs
In acc. with regulation (EU) No. 66/2014
MIELE
Model name / identifier
Number of cooking zones and/or areas
CS 1212-1
2
For circular cooking zones: diameter of useful surface area/cooking zone
For non-circular cooking zones or areas: length and width of useful surface area per electric cooking zone or area
1. = Ø 100-160 mm
2. = Ø 160-230 mm
3. =
4. =
5. =
6. =
Energy consumption per cooking zone or area calculated per kg (EC electric cooking
)
1. = 185,2 Wh/kg
2. = 168,9 Wh/kg
Energy consumption for the hob calculated per kg
(EC electric hob
)
177,1 Wh/kg
Information for domestic electric hobs
In acc. with regulation (EU) No. 66/2014
MIELE
Model name / identifier
Number of cooking zones and/or areas
For circular cooking zones: diameter of useful surface area/cooking zone
For non-circular cooking zones or areas: length and width of useful surface area per electric cooking zone or area
CS 1221-1
1
1. = Ø 180-300 mm
2. =
3. =
4. =
5. =
6. =
Energy consumption per cooking zone or area calculated per kg (EC electric cooking
)
1. = 170,3 Wh/kg
Energy consumption for the hob calculated per kg
(EC electric hob
)
170,3 Wh/kg
56
Product data sheets
Information for domestic electric hobs
In acc. with regulation (EU) No. 66/2014
MIELE
Model name / identifier
Number of cooking zones and/or areas
CS 1222
2
For circular cooking zones: diameter of useful surface area/cooking zone
For non-circular cooking zones or areas: length and width of useful surface area per electric cooking zone or area
1. = Ø 100-160 mm
2. = Ø 200 / 200x300 mm
3. =
4. =
5. =
6. =
Energy consumption per cooking zone or area calculated per kg (EC electric cooking
)
1. = 185,2 Wh/kg
2. = 188,7 Wh/kg
Energy consumption for the hob calculated per kg
(EC electric hob
)
187,0 Wh/kg
57
United Kingdom
Miele Co. Ltd.
Fairacres, Marcham Road
Abingdon, Oxon, OX14 1TW
Customer Contact Centre Tel: 0330 160 6600
E-mail: [email protected]
Internet: www.miele.co.uk
Australia
Miele Australia Pty. Ltd.
ACN 005 635 398
ABN 96 005 635 398
1 Gilbert Park Drive, Knoxfield, VIC 3180
Tel: 1300 464 353
Internet: www.miele.com.au
China
Miele (Shanghai) Trading Ltd.
1-3 Floor, No. 82 Shi Men Yi Road
Jing' an District
200040 Shanghai, PRC
Tel: +86 21 6157 3500, Fax: +86 21 6157 3511
E-mail: [email protected], Internet: www.miele.cn
Miele (Hong Kong) Limited
41/F - 4101, Manhattan Place
23 Wang Tai Road
Kowloon Bay, Hong Kong
Tel: (852) 2610 1025, Fax: (852) 3579 1404
Email: [email protected]
Website: www.miele.hk
India
Miele India Pvt. Ltd.
Ground Floor, Copia Corporate Suites
Plot No. 9, Jasola, New Delhi - 110025
Tel: 011-46 900 000, Fax: 011-46 900 001
E-mail: [email protected], Internet: www.miele.in
Ireland
Miele Ireland Ltd.
2024 Bianconi Avenue
Citywest Business Campus, Dublin 24
Tel: (01) 461 07 10, Fax: (01) 461 07 97
E-Mail: [email protected], Internet: www.miele.ie
Manufacturer: Miele & Cie. KG
Carl-Miele-Straße 29, 33332 Gütersloh, Germany
Malaysia
Miele Sdn Bhd
Suite 12-2, Level 12
Menara Sapura Kencana Petroleum
Solaris Dutamas No. 1, Jalan Dutamas 1
50480 Kuala Lumpur, Malaysia
Phone: +603-6209-0288
Fax: +603-6205-3768
New Zealand
Miele New Zealand Limited
IRD 98 463 631
Level 2, 10 College Hill
Freemans Bay, Auckland 1011, NZ
Tel: 0800 464 353
Internet: www.miele.co.nz
Singapore
Miele Pte. Ltd.
163 Penang Road
# 04 - 03 Winsland House II
Singapore 238463
Tel: +65 6735 1191, Fax: +65 6735 1161
E-Mail: [email protected]
Internet: www.miele.sg
South Africa
Miele (Pty) Ltd
63 Peter Place, Bryanston 2194
P.O. Box 69434, Bryanston 2021
Tel: (011) 875 9000, Fax: (011) 875 9035
E-mail: [email protected]
Internet: www.miele.co.za
United Arab Emirates
Miele Appliances Ltd.
Gold & Diamond Park
Office No. 6-217, Sheikh Zayed Road
P.O. Box 11 47 82 - Dubai
Tel. +971 4 3044 999
Fax. +971 4 3418 852
800-MIELE (64353)
E-Mail: [email protected]
Website: www.miele.ae
CS 1212-1 I / CS 1221 I / CS 1222 I
en-GB M.-Nr. 09 055 450 / 06
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement