advertisement
SHINDAIWA OWNER’S/OPERATOR’S MANUAL
T235 TRIMMER
X7722277201
1/16
WARNING!
Minimize the risk of injury to yourself and others! Read this manual and familiarize yourself with the contents. Always wear eye and hearing protection when operating this unit.
Introduction
Shindaiwa hand-held power equipment is designed and built to deliver superior performance and reliability without compromise to quality, comfort, safety or durability. Shindaiwa engines represent the leading edge of high-performance engine technology, delivering exceptionally high power with remarkably low displacement and weight. As an owner/operator, you’ll soon discover for yourself why Shindaiwa is simply in a class by itself!
IMPORTANT!
The information contained in these instructions describes units available at the time of publication.
ECHO, Inc. reserves the right to make changes to products without prior notice, and without obligation to make alterations to units previously manufactured.
WARNING!
The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm.
Table of Contents
PAGE
Safety ................................................... 3
Product Description .............................. 5
Specifications ....................................... 6
Emission Control .................................. 6
Assembly .............................................. 6
Mixing fuel ............................................ 8
Filling the fuel tank................................ 9
Starting the Engine ............................ 10
PAGE
Stopping the Engine ............................11
Checking Unit Condition ..................... 12
Operation ............................................ 12
Maintenance ....................................... 13
Long Term Storage ............................. 19
Troubleshooting Guide ....................... 20
Warranty ............................................ 23
Product Registration .......................... 25
IMPORTANT!
The operational procedures described in this manual are intended to help you get the most from this unit as well as to protect you and others from harm. These procedures are guidelines for safe operation under most conditions, and are not intended to replace any safety rules and/or laws that may be in force in your area. If you have questions regarding your hand-held power equipment, or if you do not understand something in this manual, contact Shindaiwa at the address printed on the back of this
Manual.
Attention Statements
Throughout this manual are special “attention statements”.
IMPORTANT!
A statement preceded by the word “IMPORTANT” is one that possesses special significance.
DANGER!
A statement preceded by the triangular attention symbol and the word “DANGER” contains information that should be acted upon to prevent serious injury or death.
CAUTION!
A statement preceded by the word “CAUTION” contains information that should be acted upon to prevent mechanical damage.
WARNING!
A statement preceded by the triangular attention symbol and the word “WARNING” contains information that should be acted upon to prevent serious bodily injury.
NOTE:
A statement preceded by the word “NOTE” contains information that is handy to know and may make your job easier.
2
Warning and Operational Labels
Read and follow this operator's manual. Failure to do so could result in serious injury..
50 FEET
(15m )
Make sure no one is within
15 M / 50 feet of an operating machine.
Wear eye and hearing protection at all times during operation of this unit. Wear head protection where there is a risk of falling objects.
Beware of thrown or richocheted objects
WARNING: Surface can be hot. Always wear gloves when handling this unit.
Do not use blades.
String line only
Safety
Work Safely
Trimmers and brushcutters operate at very high speeds and can do serious damage or injury if they are misused or abused.
Never allow a person without training or instruction to operate this unit!
WARNING!
Never make unauthorized attachment installations.
Stay Alert
You must be physically and mentally fit to operate this unit safely.
WARNING!
Never operate power equipment of any kind if you are tired or if you are under the influence of alcohol, drugs, medication or any other substance that could affect your ability or judgement.
WARNING!
Use Good Judgment
ALWAYS inspect unit before each use. Replace any damaged parts.
NEVER run the engine when transporting the unit.
NEVER run the engine indoors! Make sure there is always good ventilation. Fumes from engine exhaust can cause serious injury or death.
ALWAYS stop the unit immediately if it suddenly begins to vibrate or shake. Inspect for broken, missing or improperly installed parts or attachments.
NEVER extend trimming line beyond the length specified for your unit.
ALWAYS keep the unit as clean as practical. Keep it free of loose vegetation, mud, etc.
ALWAYS hold the unit firmly with both hands when cutting or trimming, and maintain control at all times.
ALWAYS use the proper cutting tool for the job.
ALWAYS keep the handles clean
ALWAYS disconnect the spark plug wire before performing any maintenance work.
WARNING!
Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects away from all openings.
• ALWAYS stop engine, disconnect spark plug, and make sure all moving parts have come to a complete stop before removing obstructions, clearing debris, or servicing unit.
• DO NOT start or operate unit unless all guards and protective covers are properly assembled to unit.
• NEVER reach into any opening while the engine is running. Moving parts may not be visible through openings.
WARNING!
The ignition components of this machine generate an electromagnetic field during operation which may interfere with some pacemakers. To reduce the risk of serious or fatal injury, persons with pacemakers should consult with their physician and the pacemaker manufacturer before operating this machine. In the absence of such information, ECHO does not recommend the use of ECHO products by anyone who has a pacemaker.
3
Safety Labels
This label indicates the minimum distance between front handle and rear grip per ANSI B175.3.
4
IMPORTANT!
Safety and Operation Information Labels: Make sure all information labels are undamaged and readable.
Immediately replace damaged or missing information labels. New labels are available from your local authorized Shindaiwa dealer.
The Properly Equipped Operator broad-brimmed hat or helmet. A helmet brushcutter to clear small trees.
is fatiguing and could lead to impaired hearing.
Wear close-fitting clothing to protect legs and arms. Gloves offer added protection and are strongly recommended. Do not wear clothing or jewelry that could get caught in machinery or underbrush. Secure long hair
NEVER wear shorts!
Keep a proper footing and times during operation.
do not boots or shoes): do not wear opentoed shoes or sandals. Never work barefooted!
READ THE
OPERATOR’S MANUAL
WEAR HEARING AND ANSI Z87.1
APPROVED EYE PROTECTION
(15m )
KEEP BYSTANDERS AWAY
AT LEAST 50 FEET (15m)
BEWARE OF THROWN OR
RICOCHETED OBJECTS
DO NOT OPERATE THIS
MACHINE WITH A BLADE
Shindaiwa Inc.
19422-00028 goggles or safety glasses to shield against thrown objects.
It adds comfort and helps ensure safety by limiting movement fore and aft. When the harness is adjusted properly, the unit should balance with the cutting attachment parallel to the ground.
shield is correctly installed and in good condition. Do not operate the unit if the cutting attachment shield
Keep away from the rotating trimmer line at all times, and never lift a moving attachment above waist-high.
Be Aware of the Working Environment operation in very hot or very cold weather.
of slippery terrain, weather.
Be constantly alert for objects and debris that could be thrown either from the rotating cutting attachment or bounced from a hard surface.
bystanders or observers outside the
15 meter (50 zone” wear eye protection.
15 METERS (50
FEET)
cutting attachment installed.
Reduce the risk of bystanders being struck by flying debris. Make sure no one is within 15 meters (50 feet)— that’s about 16 paces of an operating attachment. Stop immediately if a child, pet, or person comes within a 15 meter
(50 feet)radius. Outside this radius, objects.
Do not operate the unit if the cutting attachment shield is missing, loose, or broken.
If contact is made with a hard object, attachment for damage.
or hidden debris that could be thrown back at you or toward a bystander.
When operating in rocky terrain or near electric wires or fences, use extreme caution to avoid contacting such items with the cutting attachment.
Product Description
Gearcase
Outer Tube
Ignition
Switch
Throttle
Interlock
Spark plug
Handle
Cutting Attachment
Shield
Trimmer Head
Throttle
Trigger
Fuel
Tank
Grip Using the illustration as a guide, familiarize yourself with your machine and its various components. Understanding your machine helps ensure top performance, long service life and safer operation.
5
Specifications
Engine Name
Engine Type
Dry Weight (Without cutting attachment)
Bore x Stroke
Displacement
Fuel/Oil Ratio
Fuel Tank Capacity
Carburetor Type
Ignition
Spark Plug**
Spark Plug Gap
Torque
Air Cleaner Type
Starting Method
Stopping Method
Transmission Type
Engine Idle Speed
Clutch Engagement Speed
Wide Open Throttle Speed (W.O.T.)
T235
2-cycle, vertical cylinder, air cooled
5.1 kg/12.1 lb.
32.2 x 26.0 mm (1.27 x 1.02 in.)
21.2 cc (1.29 cu. in.)
50:1 Shindaiwa Red Armor® *ISO-L-EGD or JASO FD class engine oil
.44 L (14.9 oz.)
Diaphragm-type carburetor
Flywheel magneto, capacitor discharge
NGK BPMR8Y
0.6 mm (0.024 in)
16.7 - 18.6 N∙m (148-165 in • lbf)
Foam pre-filter; sealed felt main filter
Recoil
Slide switch
Automatic, centrifugal clutch w/bevel gear
2,750 RPM
3,850 RPM
8,400 RPM
Specifications are subject to change without notice.
IMPORTANT!
This spark ignition system complies with the Canadian standard ICES-002.
Emission Control (Exhaust & Evaporative)
EPA 2010 and Later
The emission control system for the engine is EM (engine modification) and, if the second to last character of the
Engine Family on the Emission Control Information label (sample below) is “B”, “C”, “K”, or “T”, the emission control system is EM and TWC (3-way catalyst). The fuel tank/fuel line emission control system is EVAP (evaporative emissions). Evaporative emissions for California models are only applicable to fuel tanks.
An Emission Control Label is located on the engine. (This is an EXAMPLE ONLY, information on label varies by engine FAMILY).
PRODUCT EMISSION DURABILITY (EMISSION COMPLIANCE PERIOD)
The 50 or 300 hour emission compliance period is the time span selected by the manufacturer certifying the engine emissions output meets applicable emissions regulations, provided that approved maintenance procedures are followed as listed in the Maintenance Section of this manual.
Assembly
This unit is factory pre-assembled. Assembly tools are not supplied with this unit.
6
Contents
■
Safety Glasses
■
Operator’s Manual
■
Emission Control Warranty Statement
Cutting attachment shield
CAUTION
Wear Gloves or personal injury may result:
• Cutoff knife is sharp.
• Gearcase and surrounding area may be hot.
NOTE:
The plastic shield is for use with the Nylon Line Head only. Install Metal
Shield when using plastic or metal blades.
1. Remove plastic threaded shaft sleeve and adapter plate (C) from PTO shaft (A).
2. Place the shield on the bottom of the bearing housing flange.
3. Place shield plate (B) on shield, align holes. Install three (3) screws from bottom through plate and shield into gear case.
4. Assemble adapter plate (C) onto PTO shaft.
Install trimmer head
NOTE:
Use the 4 mm hexagonal wrench as a gear housing locking tool.
1. Be sure adapter plate (C) remains on PTO shaft (A).
2. Align locking hole in upper plate with notch in edge of gear housing and insert head locking tool (D).
3. Thread line head (E) onto shaft by turning it counter-clockwise until head is tight against adapter plate (C).
4. Remove locking tool (D).
IMPORTANT!
Semi-automatic nylon line heads must be used only with plastic debris shield with cut-off knife. Using nylon line heads with metal debris shield can result in trimmer damage, caused by operation with excessive line length.
To advance trimmer line
NOTE:
To advance trimmer line, tap trimmer head against the ground while the head is turning at normal operating speed.
Nylon line replacement
See Maintenance Section for Loading Trimmer Line.
Remove nylon line head
NOTE:
Do not disassemble nylon line head.
C
D
C
E
D
B
A
A
1. Align locking hole in upper plate with notch in edge of gear housing and insert head locking tool (D).
2. Remove line head (E) by turning it clockwise until head is completely off of shaft.
3. Remove locking tool (D).
WARNING!
A standard grass trimmer with a loop handle should NEVER be operated with blade-type attachments. For blade use, the trimmer must be fitted with a bicycle-type handlebar or a barrier bar that is located in front of the operator to reduce the risk of the operator from coming in contact with the cutting attachment (per ANSI B175.3). When using a blade, the unit must also be equipped with a harness or strap.
7
8
Front handle installation
NOTE:
Label shows minimum spacing for front handle location.
1. Position front handle for comfortable operation and tighten screw.
Handle
Outer Tube
Screw
Handle Position Label
Mixing Fuel
WARNING!
Diesel fuels and alternative fuels, such as E15 (15% ethanol), E85 (85% ethanol) or any fuels not meeting
Shindaiwa requirements are NOT approved for use in Shindaiwa 2-stroke or Hybrid 4-stroke gasoline engines.
Use of diesel or alternative fuels may cause performance problems, loss of power, overheating, fuel vapor lock, and unintended machine operation, including, but not limited to, improper clutch engagement. Diesel or alternative fuels may also cause premature deterioration of fuel lines, gaskets, carburetors and other engine components.
Fuel Requirements
Gasoline - Use 89 Octane [R+M/2] (mid grade or higher) gasoline known to be good quality. Gasoline may contain up to
10% Ethanol (grain alcohol) or 15% MTBE (methyl tertiary-butyl ether). Gasoline containing methanol (wood alcohol) is NOT approved. ECHO brand Power Fuel™ is 93 octane, ethanol-free fuel premixed with ECHO Red Armor® engine oil at 50:1 ratio. Use of ECHO Power Fuel™ is recommended to extend engine life in all air-cooled 2-stroke and 2/4-stroke hybrid engines.
2 Stroke Mixture Oil - A 2-stroke engine oil meeting ISO-L-EGD (ISO/CD 13738) and J.A.S.O. M345/FD standards must be used. Shindaiwa Red Armor TM 2-Stroke Oil is strongly recommended as it meets this standard and is specifically formulated for use in all Shindaiwa 2-stroke engines. Engine problems due to inadequate lubrication caused by failure to use an ISO-L-EGD (ISO/CD 13738) and J.A.S.O. M345/FD certified oil will void the engine warranty.
IMPORTANT!
Shindaiwa Red Armor TM fied in those manuals.
2-Stroke oil engine oil may be mixed at 50:1 ratio for application in all Shindaiwa engines sold in the past, regardless of ratio speci-
IMPORTANT!
Stored fuel ages. Do not mix more fuel than you expect to use in thirty (30) days, ninety (90) days when a fuel stabilizer is added. Use of unmixed, improperly mixed, or stale fuel, may cause hard starting, poor performance, or severe engine damage and void the product warranty. Read and follow instructions in the Long Term Storage section of this manual.
Examples of 50:1 mixing quantities
Handling Fuel
DANGER
Fuel is VERY flammable. Use extreme care when mixing, storing or handling or serious personal injury may result.
• Use an approved fuel container.
• DO NOT smoke near fuel.
• DO NOT allow flames or sparks near fuel.
• Fuel tanks/cans may be under pressure. Always loosen fuel caps slowly allowing pressure to equalize.
• NEVER refuel a unit when the engine is HOT or RUNNING!
• DO NOT fill fuel tanks indoors. ALWAYS fill fuel tanks outdoors over bare ground.
• DO NOT overfill fuel tank. Wipe up spills immediately.
• Securely tighten fuel tank cap and close fuel container after refueling.
• Inspect for fuel leakage. If fuel leakage is found, do not start or operate unit until leakage is repaired.
• Move at least 3m (10 ft.) from refueling location before starting the engine.
Mixing Instructions
1. Fill an approved fuel container with half of the required amount of gasoline.
2. Add the proper amount of engine oil to gasoline.
3. Close container and shake to mix oil with gasoline.
4. Add remaining gasoline, close fuel container, and remix.
IMPORTANT!
Spilled fuel is a leading cause of hydrocarbon emissions.
Some states may require the use of automatic fuel shutoff containers to reduce fuel spillage.
After use
• DO NOT store a unit with fuel in its tank. Leaks can occur. Return unused fuel to an approved fuel storage container.
Filling the fuel tank
WARNING!
Minimize the Risk of Fire
■
NEVER smoke or light fires near the engine.
■
ALWAYS stop the engine and allow it to cool before refueling.
■
ALWAYS Wipe all spilled fuel and move at least 3 meters (10 feet) from the fueling point and source before starting.
■
NEVER place flammable material close to the engine muffler.
■
NEVER operate the engine without the muffler and spark arrester screen in place and in good working condition.
■
FUEL IS HIGHLY FLAMMABLE.
Storage - Fuel storage laws vary by locality. Contact your local government for the laws affecting your area.
As a precaution, store fuel in an approved, airtight container. Store in a well-ventilated, unoccupied building, away from sparks and flames.
IMPORTANT!
Stored fuel may separate. ALWAYS shake fuel container thoroughly before each use.
■
ALWAYS store gasoline in a container approved for flammable liquids.
■
ALWAYS inspect the unit for fuel leaks before each use. During each refill, check that no fuel leaks from around the fuel cap and/or fuel tank.
If fuel leaks are evident, stop using the unit immediately. Fuel leaks must be repaired before using the unit.
■
ALWAYS move the unit at least 3 meters (10 feet) away from a fuel storage area or other readily flammable materials before starting the engine.
CAUTION!
Slowly remove the fuel cap only after stopping the engine
1. Place the unit on a flat, level surface.
2. Clear any dirt or other debris from around the fuel filler cap.
3. Remove the fuel cap, and fill the tank with clean, fresh fuel.
4. Reinstall the fuel filler cap and tighten firmly.
5. Wipe away any spilled fuel before starting engine.
9
Starting the Engine
WARNING!
The attachment will operate immediately when the engine starts, and could result in possible serious injury. Keep movable parts of the attachment away from objects that could become entangled or thrown, and surfaces that could cause loss of control.
Starting Cold Engine
1. Stop Switch
Move stop switch button (A) forward away from the STOP position.
2. Choke
Move choke lever (B) to Cold Start Position ( ).
3. Purge Bulb
Pump purge bulb (C) until fuel is visible and flows freely in the clear fuel tank return line. Pump bulb an additional 4 or 5 times.
A
4.
Recoil Starter
Lay the unit on a flat area and keep movable attachment parts clear of all obstacles. Firmly grasp right hand grip and throttle trigger lockout with left hand and fully depress throttle trigger to wide open position. Rapidly pull recoil starter handle/rope (D) until engine fires (or maximum five [5] pulls).
5.
Choke
After engine fires (or 5 pulls), move choke lever back to Run ( ) position. Hold throttle trigger and throttle trigger lockout fully depressed, and pull recoil starter handle/rope until engine starts and runs. Release throttle trigger, and allow unit to warm up at idle for several minutes.
NOTE:
If engine does not start with choke in “Run” position after 5 pulls, repeat instructions 2 - 5.
B
C
D
6. Throttle Trigger
After engine warm-up, gradually depress throttle trigger to increase engine RPM to operating speed.
10
Starting Warm Engine
The starting procedure is the same as Cold Start except DO NOT close the choke, and do not hold throttle trigger fully depressed.
WARNING!
The attachment should not move at idle, otherwise serious personal injury may result.
NOTE:
If attachment moves, readjust carburetor according to “Carburetor Adjustment” instructions in this manual or see your ECHO Dealer.
1. Stop Switch
Move stop switch button (A) forward away from the STOP position.
2. Purge Bulb
Pump purge bulb (C) until fuel is visible in the "Clear" fuel return line.
3. Recoil
Lay the unit on a flat area and keep movable attachment parts clear of all obstacles. Rapidly pull the recoil starter handle (D) until the engine fires.
NOTE:
If engine does not start after 5 pulls, use Cold Start Procedure .
B
C
D
Stopping the Engine
1.
Release Throttle.
Allow engine to return to idle before shutting off engine.
2.
Stop Switch
Move stop switch button (A) backward to STOP position.
WARNING!
If engine does not stop when stop switch is moved to STOP position, close choke - COLD START position - to stall engine. Have your
ECHO dealer repair stop switch before using trimmer again.
A
A
11
Checking Unit Condition
NEVER operate the unit with the cutting attachment shield or other protective devices removed!
Use only authorized Shindaiwa parts and accessories with your Shindaiwa trimmer. Do not make modifications to this unit without written approval from
Shindaiwa, Inc.
ALWAYS make sure the cutting attachment is properly installed and firmly tightened before operation.
NEVER use a cracked or warped cutting attachment; replace it with a serviceable one.
ALWAYS make sure the cutting attachment fits properly into the appropriate attachment holder. If a properly installed attachment vibrates, replace the attachment with new one and re-check.
ALWAYS stop the engine immediately and check for damage if you strike a foreign object or if the unit becomes tangled. Do not operate with broken or damaged equipment.
NEVER allow the engine to run at high
RPM without a load. Doing so could damage the engine.
NEVER operate a unit with worn or damaged fasteners or attachment holders.
WARNING!
A cutting attachment shield or other protective device is no guarantee of protection against ricochet. YOU
MUST ALWAYS GUARD AGAINST
FLYING DEBRIS!
Operation
WARNING!
Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects away from all openings. Always stop engine, disconnect spark plug, and make sure all moving parts have come to a complete stop before removing obstructions, clearing debris, or servicing unit.
WARNING!
Engine exhaust IS HOT, and contains Carbon Monoxide (CO), a poison gas. Breathing CO can cause unconsciousness, serious injury, or death. Exhaust can cause serious burns. ALWAYS position unit so that exhaust is directed away from your face and body..
WARNING!
Operation of this equipment may create sparks that can start fires. This unit is equipped with a spark arrestor to prevent discharge of hot particles from the engine. Metal blade use also can create sparks if the blade strikes rocks, metal, or other hard objects. Contact local fire authorities for laws or regulations regarding fire prevention requirements.
IMPORTANT!
The terms “left”, “left-hand”, and “LH”; “right”, “right-hand”, and “RH”; “front” and “rear” refer to directions as viewed by the operator during normal operation.
Cutting grass with a trimmer head
Your Shindaiwa unit may be equipped with one of several Shindaiwa trimmer head models, each with features for specific applications and/or operational requirements.
NOTE:
For proper operation, always refer to the instructions accompanying the trimmer head being used.
12
Trimmer head styles:
Semi-automatic. Trimmer line is indexed when the operator taps the trimmer head on the ground during operation.
Manual. The operator indexes line manually with the grass trimmer stopped.
Fixed. The operator must stop the unit and add new lengths of trimmer line manually.
Flail. This device, designed for clearing weeds and light brush, features three nylon blades attached to the head by pivots.
NOTE:
Additional hardware may be required to mount the Fixed Line or the Flail type trimmer heads.
Engine Operating Speeds
Operate at full throttle while cutting grass.
Trimming and Mowing Grass
Hold the grass trimmer so the trimmer head is angled slightly into the area to be cut.
To ensure maximum trimmer-line service life, cut only with the tip of the trimmer line.
Cut grass by swinging the unit's trimmer head from left to right. Keep the trimmer head horizontal.
CAUTION!
■
Do not push the rotating line into trees, wire fences or any material that could tangle or break line ends.
■
Operation of trimmer without a cutting attachment shield and using excessive line length can lead to premature clutch failure.
■
Operation at low rpm can lead to premature clutch failure.
IMPORTANT!
MAINTENANCE, REPLACEMENT OR REPAIR OF EMISSION CONTROL DEVICES AND SYSTEMS MAY BE PERFORMED
BY ANY REPAIR ESTABLISHMENT OR INDIVIDUAL; HOWEVER, WARRANTY REPAIRS MUST BE PERFORMED BY A
DEALER OR SERVICE CENTER AUTHORIZED BY ECHO,INC. THE USE OF PARTS THAT ARE NOT EQUIVALENT IN PER-
FORMANCE AND DURABILITY TO AUTHORIZED PARTS MAY IMPAIR THE EFFECTIVENESS OF THE EMISSION CON-
TROL SYSTEM AND MAY HAVE A BEARING ON THE OUTCOME OF A WARRANTY CLAIM.
NOTE:
Using non-standard replacement parts could invalidate your Shindaiwa warranty.
WARNING!
Before performing any maintenance, repair, or cleaning work on the unit, make sure the engine and cutting attachment are completely stopped. Disconnect the spark plug wire before performing service or maintenance.
WARNING!
Non-standard accessories, cutting attachment, or replacement parts may not operate properly with your unit and may cause damage and lead to personal injury.
13
This unit must never be operated with a faulty or missing spark arrester or muffler. Make sure the muffler is well secured and in good condition. A worn or damaged muffler is a fire hazard and may also cause hearing loss.
Spark Plug
Keep the spark plug and wire connections tight and clean.
Fasteners
Make sure nuts, bolts, and screws (except carburetor adjusting screws) are tight.
Daily maintenance
Prior to each work day, perform the following:
■
Remove all dirt and debris from the engine, check the cooling fins and air cleaner for clogging, and clean as necessary.
■
Carefully remove any accumulations of dirt or debris from the muffler and fuel tank. Check cooling air intake area at base of crankcase. Remove all debris. Dirt build-up in these areas can lead to engine overheating, fire, or premature wear.
Cooling fins
Cooling fins
Remove all dirt and debris from the engine and check the cooling fins
WARNING!
Always wear gloves when working around the cutter assembly.
■
Clean any debris or dirt from the cutting attachment.
■
■
Check for loose or missing screws or components. Make sure the cutter attachment is securely fastened.
Check the entire unit for leaking fuel or grease.
■
Air intake
Make sure nuts, bolts, and screws
(except carburetor idle speed adjusting screws) are tight.
10-Hour maintenance
(more frequently in dusty conditions)
1. Remove the air filter cover by loosening the cover screw.
2. Remove and inspect the pre-filter.
If the pre-filter is torn or otherwise damaged, replace it with a new one.
3. Clean the pre-filter with soap and water. Let dry before reinstalling.
4. Inspect the air filter element. If the element is damaged or distorted, replace it with a new one.
5. Tap filter gently on a hard surface to dislodge debris from element or use compressed air from the inside to blow debris out and away from the air filter element.
6. Install the air filter element, pre-filter and cover in the reverse order of removal.
14
IMPORTANT!
Direct the air stream at the inside face of the filter only!
CAUTION!
Never operate the unit if the air cleaner assembly is damaged or missing!
Maintenance (continued)
10/15-Hour maintenance
Remove and clean or replace the spark plug.
■
Clean the spark plug. Adjust electrode gap according to the values listed in the ”Specifications” section.
If the spark plug must be replaced, use only the type recommended in
”Specifications” or equivalent resistor type spark plug of the correct heat range.
CAUTION!
Before removing the spark plug, clean the area around the plug to prevent dirt and debris from getting into the engine’s internal parts.
Remove and inspect spark plug
Every 50 hours of operation; more frequently in dusty conditions:
Gear Housing
1. Clean all loose debris from gear box.
2. Remove plug (A) and check level of grease. Grease should fill gear case to bottom of grease plug hole.
3. Add grease if necessary using manual grease gun or squeeze-type tube.
Do not use high pressure grease gun. DO NOT over-fill.
Clean the spark plug and check the gap at the electrode.
0,6 mm
A
50 hour maintenance
Remove and replace the fuel filter element.
■
Use a hooked wire to extract the fuel filter from inside the fuel tank. Inspect the fuel filter element. If it shows signs of contamination, replace with a genuine Shindaiwa replacement fuel filter element.
■
Before reinstalling the new filter element, inspect the condition of all the fuel system components (fuel pick-up line, fuel return line, tank vent line, tank vent, fuel cap and fuel tank).
■
If damage, splitting or deterioration is noted, the unit should be removed from service until it can be inspected or repaired by a Shindaiwa-trained service technician.
CAUTION!
Make sure you do not pierce the fuel line with the end of the hooked wire. The line is delicate and can be damaged easily.
Hooked wire
Fuel filter element
NOTE:
Federal EPA regulations require all model year 2012 and later gasoline powered engines produced for sale in the United
States to be equipped with a special low permeation fuel supply hose between the carburetor and fuel tank. When servicing model year 2012 and later equipment, only fuel supply hoses certified by EPA can be used to replace the original equipment supply hose. Fines up to $37,500 may be enforced for using an un-certified replacement part.
15 spark plug gap--all models
Maintenance (continued)
Muffler and spark arrester maintenance
If the engine becomes sluggish and low on power, check and clean the spark arrester screen.
WARNING!
Never operate the unit with a damaged or missing muffler or spark arrester! Operating with a missing or damaged spark arrester is a fire hazard and could also damage your hearing.
1. Remove the engine cover (A).
2. Remove the muffler (B).
3. Remove the spark arrester screen (C) and cover.
4. Clean the screen with a stiff bristle brush.
5. Inspect the cylinder exhaust port for any carbon buildup.
6. Reassemble in the reverse order of disassembly.
IMPORTANT!
If you note excessive carbon buildup, consult with an authorized servicing dealer.
A
B
C
16
Maintenance (continued)
Carburetor Adjustment
Engine Break-In
New engines must be operated a minimum duration of two tanks of fuel break-in before carburetor adjustments can be made. During the break-in period your engine performance will increase and exhaust emissions will stabilize. Idle speed can be adjusted as required.
High Altitude Operation
This engine has been factory adjusted to maintain satisfactory starting, emission, and durability performance up to
1,100 feet above sea level (ASL) (96.0 kPa). To maintain proper engine operation and emission compliance above
1,100 feet ASL the carburetor may need to be adjusted by an authorized ECHO service dealer.
IMPORTANT!
If the engine is adjusted for operation above 1,100 feet
ASL, the carburetor must be re-adjusted when operating the engine below 1,100 feet ASL, otherwise severe engine damage may result.
NOTE:
Every unit is run at the factory and the carburetor is set in compliance with emission regulations. Carburetor adjustments, other than idle speed, must be performed by an authorized
Shindaiwa dealer..
Adjusting Engine Idle
The engine must return to idle speed whenever the throttle lever is released. Idle speed is adjustable, and must be set low enough to permit the engine clutch to disengage the cutting attachment.
Idle Ajustment
Screw
WARNING!
The cutting attachment must NEVER move at engine idle! If the idle speed cannot be adjusted by the procedure described here, return the unit to your Shindaiwa dealer for inspection.
Idle Speed Adjustment
1. Place the unit on the ground, then start the engine, and then allow it to idle 2-3 minutes until warm.
2. If the attachment moves when the engine is at idle, reduce the idle speed by turning the idle adjustment screw counter-clockwise.
3. If a tachometer is available, adjust idle. Check Specifications page for correct idle speed.
17
Nylon Line Head Disassembly Instructions
NOTE:
For normal use, Speed Feed head disassembly is not necessary. However, if circumstances require disassembly, follow these instructions .
1. Press top of locking tabs (A) on both sides of Speed Feed head to release cover (B) from eyelet carrier(C).
2. Remove cover from eyelet carrier.
Nylon Line Replacement
1. Cut one piece of line to recommended length.
.080 (2.0 mm) dia. – 20’ (6 m)
.095 (2.4 mm) dia. – 20’ (6 m)
2. Align arrows on top of knob with openings in eyelets
3. Insert one end of trimmer line into an eyelet, and push line equal distance through trimmer head.
4. Hold trimmer head while turning knob clockwise to wind line onto spool until about 5” (13 cm) of each line remains exposed.
Trimmer head is now fully loaded and ready for operation.
18
C
A
B
IMPORTANT!
When the wear indicators located at the bottom of the Speed-Feed head are worn smooth, or if holes appear, replacement of the cover or the entire Speed-Feed head is required.
Wear Indicators
Wear Indicators
Long Term Storage
Whenever the unit will not be used for 30 days or longer, use the following procedures to prepare it for storage:
■
Clean external parts thoroughly and apply a light coating of oil to all metal surfaces.
■
Drain all the fuel from the carburetor and the fuel tank.
To do so:
1. Prime the primer bulb until no more fuel is passing through.
2. Start and run the engine until it stops running.
3. Repeat steps 1 and 2 until the engine will no longer start.
CAUTION!
Gasoline stored in the carburetor for extended periods can cause hard starting, and could also lead to increased service and maintenance costs.
IMPORTANT!
All stored fuels should be stabilized with a fuel stabilizer such as STA-BIL™.
NOTE
Damage resulting from stale or contaminated fuel is not covered by the
Shindaiwa warranty policy.
■
Remove the spark plug and pour about 1/4 oz. of engine oil into the cylinder through the spark plug hole.
Slowly pull the recoil starter 2 or
3 times so oil will evenly coat the interior of the engine. Reinstall the spark plug.
■
Before storing the unit, repair or replace any worn or damaged parts.
■
Remove the air cleaner element from the carburetor and clean it thoroughly with soap and water. Let dry and reassemble the element.
■
Store the unit in a clean, dust-free area.
19
Troubleshooting Guide
What To Check
Vaporlock.
ENGINE DOES NOT START OR HARD TO START
Possible Cause Remedy
Engine hot/heat soaked.
Let cool completely and restart.
Low fuel quality.
Refi ll with fresh, clean unleaded gasoline with a pump octane of 89 or higher mixed with an air cooled engine oil that meets or exceeds ISO-L-EGD and/or JASO FD classifi ed oils at 50:1 gasoline/oil ratio.
What To Check
Does the engine crank?
YES
Good compression?
YES
NO
NO
ENGINE DOES NOT START
Possible Cause Remedy
Consult with an authorized Shindaiwa servicing dealer.
Faulty recoil starter.
Fluid in the crankcase.
Internal damage.
Loose spark plug.
Excess wear on cylinder, piston, rings.
Tighten and re-test.
Consult with an authorized Shindaiwa servicing dealer.
Does the tank contain fresh fuel of the proper grade?
YES
NO
Fuel incorrect, stale, or
contaminated; mixture incorrect.
Refi ll with fresh, clean unleaded gasoline with a pump octane of 89 or higher mixed with an air cooled engine oil that meets or exceeds ISO-L-EGD and/or JASO FD classifi ed oils at 50:1 gasoline/oil ratio.
Is fuel visible and moving in the return line when priming?
YES
Is there spark at the spark plug wire terminal?
YES
NO
NO
Check for clogged fuel fi lter and/or vent.
Priming pump not functioning properly.
The ignition switch is in
“O” (OFF) position.
Shorted ignition ground.
Faulty ignition unit.
Replace fuel fi lter or vent as required.
Re-start.
Consult with an authorized Shindaiwa servicing dealer.
Move switch to “I” (ON) position and re-start.
Consult with an authorized Shindaiwa servicing dealer.
Check the spark plug.
If the plug is wet, excess fuel may be in the cylinder.
The plug is fouled or improperly
gapped.
The plug is damaged internally or of the wrong size.
See "Starting a Flooded Engine"
Clean and gap the spark plug. Check the Specifi cations section for the correct plug and gap for your unit. Restart.
Replace the spark plug. Check the Specifi cations section for the correct plug and gap for your unit. Restart.
20
Troubleshooting Guide (continued)
LOW POWER OUTPUT
What To Check
Is the engine overheating?
Possible Cause
Operator is overworking the unit.
Carburetor mixture is too lean.
Improper fuel ratio.
Remedy
Use a lower throttle setting.
Consult with an authorized Shindaiwa servicing dealer.
Refi ll with fresh, clean unleaded gasoline with a pump octane of 89 or higher mixed with an air cooled engine oil that meets or exceeds ISO-L-EGD and/or JASO FD classifi ed oils at 50:1 gasoline/oil ratio.
Fan, fan cover, cylinder fi ns dirty or damaged.
Carbon deposits on the piston or in the muffl er.
Clogged air cleaner element.
Loose or damaged spark plug.
Engine is rough at all speeds. May also have black smoke and/or unburned fuel at the exhaust.
Air leakage or clogged fuel line.
Water in the fuel.
Clean, repair or replace as necessary.
Consult with an authorized Shindaiwa servicing dealer.
Service the air cleaner element.
Tighten or replace the spark plug.
Check the Specifi cations section for the correct plug and gap for your unit.
Repair or replace fuel fi lter and/or fuel line.
Refi ll with fresh, clean unleaded gasoline with a pump octane of 89 or higher mixed with an air cooled engine oil that meets or exceeds ISO-L-EGD and/or JASO FD classifi ed oils at 50:1 gasoline/oil ratio.
Consult with an authorized Shindaiwa servicing dealer.
Engine is knocking.
Piston seizure.
Faulty carburetor and/or diaphragm.
Overheating condition.
Improper fuel.
Carbon deposits in the combustion chamber.
Consult with an authorized Shindaiwa servicing dealer.
Refi ll with fresh, clean unleaded gasoline with a pump octane of 89 or higher mixed with an air cooled engine oil that meets or exceeds ISO-L-EGD and/or JASO FD classifi ed oils at 50:1 gasoline/oil ratio.
Consult with an authorized Shindaiwa servicing dealer.
21
Troubleshooting Guide (continued)
ADDITIONAL PROBLEMS
Symptom Possible Cause
Clogged air fi lter.
Remedy
Clean the air fi lter.
Poor acceleration.
Clogged fuel fi lter.
Replace the fuel fi lter.
Lean fuel/air mixture.
Idle speed set too low.
Consult with an authorized Shindaiwa servicing dealer.
Adjust idle. Check Specifi cations page for correct idle speed.
Engine stops abruptly.
Engine diffi cult to shut off.
Engine will not idle down.
Cutting attachment moves at engine idle.
Excessive vibration.
Cutting attachment will not move.
Ignition switch turned off.
Fuel tank empty.
Water in the fuel.
Clogged fuel fi lter.
Shorted spark plug or loose terminal.
Ignition failure.
Piston seizure.
Ground (stop) wire is disconnected, or switch is defective.
Overheating due to incorrect spark plug.
Overheated engine.
Idle set too high.
Engine has an air leak.
Engine idle too high.
Broken clutch spring or worn clutch spring boss.
Loose attachment holder.
Warped or damaged attachment.
Loose gearcase.
Bent main shaft/worn or damaged bushings.
Shaft not installed in powerhead or gearcase.
Broken shaft.
Damaged gearcase.
Reset the switch and re-start.
Refi ll with fresh, clean unleaded gasoline with a pump octane of 89 or higher mixed with an air cooled engine oil that meets or exceeds ISO-L-EGD and/or JASO FD classifi ed oils at 50:1 gasoline/oil ratio.
Replace fuel fi lter.
Clean or replace spark plug. Check the Specifi cations section for the correct plug and gap for your unit. Tighten the terminal.
Replace the ignition unit.
Consult with an authorized Shindaiwa servicing dealer.
Test and replace as required.
Replace the spark plug. Check the Specifi cations section for the correct plug and gap for your unit. Restart.
Idle engine until cool.
Adjust idle. Check Specifi cations page for correct idle speed.
Consult with an authorized Shindaiwa servicing dealer.
Adjust idle. Check Specifi cations page for correct idle speed.
Replace spring/shoes as required, check idle speed.
Inspect and re-tighten holders securely.
Inspect and replace attachment as required.
Tighten gearcase securely.
Inspect and replace as necessary.
Inspect and reinstall as required.
Consult with an authorized Shindaiwa servicing dealer.
22
SHINDAIWA LIMITED WARRANTY STATEMENT FOR
PRODUCT SOLD IN USA AND CANADA BEGINNING 01/01/2015
ECHO, INC’S RESPONSIBILITY
ECHO Incorporated’s (ECHO, INC.) Limited Warranty, provides to the original purchaser that this Shindaiwa product is free from defects in material and workmanship. Under normal use and maintenance from date of purchase, ECHO, INC. agrees to repair or replace at it’s discretion, any defective product free of charge at any authorized Shindaiwa servicing dealer within listed below application time periods, limitations and exclusions. THIS LIMITED WARRANTY IS ONLY APPLICABLE TO SHINDAIWA PROD-
UCTS SOLD BY AUTHORIZED SHINDAIWA DEALERS. IT IS EXTENDED TO THE ORIGINAL PURCHASER ONLY, AND IS
NOT TRANSFERABLE TO SUBSEQUENT OWNERS EXCEPT FOR EMISSION RELATED PARTS. Repair parts and accessories replaced under this warranty are warranted only for the balance of the original unit or accessory warranty period. Any damage caused by improper installation or improper maintenance is not covered by this warranty. All parts or products replaced under warranty become the property of ECHO, INC. This warranty is separate from the Emission control warranty statement supplied with your new product. Please consult the Emission Control Warranty Statement for details regarding emission related parts. For a list of Authorized Shindaiwa Dealers refer to WWW.SHINDAIWA.COM or call 1-877-986-7783.
OWNER’S RESPONSIBILITY
To ensure trouble free warranty coverage it is important that you register your Shindaiwa equipment on-line at WWW.SHINDAIWA.
COM or by filling out the warranty registration card supplied with your unit. Registering your product confirms your warranty coverage and provides a direct link if we find it necessary to contact you.
The owner shall demonstrate reasonable care and use, and follow preventative maintenance, storage, fuel and oil usage as prescribed in the operator’s manual. Should a product difficulty occur, you must, at your expense, deliver or ship your Shindaiwa unit to an authorized Shindaiwa servicing dealer for warranty repairs (within the applicable warranty period), and arrange for pick-up or return of your unit after the repairs have been made. For your nearest authorized Shindaiwa servicing dealer, call Shindaiwa’s
Dealer Referral Center, at 1-877-986-7783 or you can locate a Shindaiwa servicing dealer at WWW.SHINDAIWA.COM. Should you require assistance or have questions concerning Shindaiwa’s Warranty Statement, you can contact our Consumer Product Support
Department at 1-800-673-1558 or contact us through the web at WWW.SHINDAIWA.COM.
PRODUCT WARRANTY PERIOD
HOMEOWNER APPLICATION
• 5 YEAR WARRANTY - Units for homeowner, or non-income producing use will be covered by this limited warranty for five (5) years from date of purchase.
EXCEPTIONS:
• For engine powered products, the electronic ignition module, flexible drive cable, and solid drive shaft are warranted for the life* of the product on parts only.
• Cutting attachments such as, but not limited to, bars, chains, sprockets, tines, blades, PowerBroom TM , belts, and nylon trimmer heads for homeowner or non-income producing use will be covered for failures due to defects in material or workmanship for a period of 60 days from original product purchase date. Any misuse from contact with concrete, rocks, or other structures is not covered by this warranty.
• Multipurpose Tool Attachments carry the same warranty duration as the units they are designed to fit.
COMMERCIAL APPLICATION
• 1 YEAR WARRANTY - All Chain Saws for commercial, institutional, agricultural, industrial, or income producing use will be covered by this limited warranty for 1 year from the date of purchase.
• 2 YEAR WARRANTY - All other units for commercial, institutional, agricultural, industrial, or income producing use will be covered by this limited warranty for two (2) years from the date of purchase.
EXCEPTIONS:
• For engine powered products, the electronic ignition module, flexible drive cables, and solid drive shafts are warranted for the life* of the product on parts only.
• Cutting attachments such as, but not limited to, bars, chains, sprockets, tines, blades, PowerBroom TM , belts, and nylon trimmer heads for commercial, institutional, agricultural, industrial, rental, or income producing will be covered for failures due to defects in material or workmanship for a period of 30 days from original product purchase date. Any misuse from contact with concrete, rocks, or other structures is not covered by this warranty.
• Multipurpose Tool Attachments carry the same warranty duration as the units they are designed to fit.
RENTAL APPLICATION - 90 DAYS WARRANTY
• Units for rental use will be covered against defects in material and workmanship for a period of 90 days from the date of purchase.
* ECHO INC’s liability under the “Lifetime” coverage is limited to furnishing parts specified under the PRODUCT Warranty
PERIOD section of this warranty statement for “Life” free of charge for a period of ten (10) years after the date of the complete unit’s final production.
23
24
PURCHASED REPAIR PARTS AND ACCESSORIES
• 90-day all applications
ATTENTION ENGINE POWERED PRODUCT OWNERS
This Shindaiwa engine powered product is a quality-engineered unit which has been manufactured to exact tolerances to provide superior performance. To help ensure the performance of the unit, it is required to use engine oil which meets the ISO-L-EGD
Standard per ISO/CD 13738 and JASO M345/FD Standards. Shindaiwa Red Armor TM is a premium engine oil specifically formulated to meet ISO-L-EGD (ISO/CD 13738) and JASO M345/FD Standards. The use of engine oils designed for other applications, such as for outboard motors or lawnmowers can result in severe engine damage, and will void your engine limited warranty.
THIS WARRANTY DOES NOT COVER DAMAGE CAUSED BY:
• Lack of lubrication or engine failure, due to the use of engine oils that do not meet the ISO-L-EGD (ISO/CD 13738) and JASO
M345/FD Standards. Shindaiwa Red Armor TM Engine Oil meets the ISO-L-EGD and JASO M345/FD Standard. Emission related
parts are covered for 5 years homeowner or 2 years commercial use regardless of two-stroke oil used, per the statement listed
in the EPA or California Emission Control Warranty Explanation.
• Damage caused by use of gasohol, containing methanol (wood alcohol), or gasoline containing less than 89 octane. Only use gasoline which contains 89 octane or higher. Gasohol which contains a maximum 10% ethanol (grain alcohol) or 15% MTBE
(methyl/tertiary/butyl/ether) is also approved. The prescribed mixing ratio of gasoline to oil is listed on the Shindaiwa oil label and covered in your operator’s manual.
• Engine damage caused by use of ether or any starting fluids.
• Damage caused by tampering with engine speed governor or emission components, or running engines above specified and recommended engine speeds as listed in your operator’s manual.
• Operation of the unit with improperly maintained/removed cutting shield or removed/damaged air filter.
• Damage caused by dirt, pressure or steam cleaning the unit, salt water, corrosion, rust, varnish, abrasives, and moisture.
• Defects, malfunctions or failures resulting from abuse, misuse, neglect, modifications, alterations, normal wear, improper servicing, or use of unauthorized attachments.
• Incorrect storage procedures, stale fuel, including failure to provide or perform required maintenance services as prescribed in the operator’s manual. Preventative maintenance as outlined in the operator’s manual is the customer’s responsibility.
• Failures due to improper set-up, pre-delivery service or repair service by anyone other than authorized Shindaiwa servicing dealer during the warranty period.
• Certain parts and other items are not warranted, including but not limited to: lubricants, starter cords, and engine tune-ups.
• Use of spark plugs other than those meeting performance and durability requirements of the OEM spark plug listed in the Operator’s Manuals.
• Overheating or carbon scoring failures due to restricted, clogged exhaust port or combustion chamber, including damage to spark arrester screen.
• Adjustments after the first (30) thirty days and beyond, such as carburetor adjustment and throttle cable adjustment.
• Damage to gears or gear cases caused by contaminated grease or oil, use of incorrect type or viscosity of lubricants, and/or failure to comply with recommended grease or oil change intervals.
• Damage caused by pump or sprayer running dry, pumping or spraying caustic or flammable materials, or lack of or broken strainers.
• Additional damage to parts or components due to continued use after operational problem or failure occurs. Should operational problem or failure occur, the product should not be used, but delivered as is to an authorized Shindaiwa servicing dealer.
It is a dealer’s and/or customer’s responsibility to complete and return the warranty registration card supplied with your Shindaiwa product or by visiting WWW.SHINDAIWA.COM. Your receipt of purchase including date, model and serial number must be maintained and presented to an authorized Shindaiwa servicing dealer for warranty service. Proof of purchase rests solely with the customer. Some states do not allow limitations on how long an implied warranty lasts, so the above limitations may not apply to you.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so you may also have other specific legal rights which vary from state to state. This limited warranty is given by ECHO Incorporated, 400 Oakwood Rd., Lake Zurich, IL
60047.
DISCLAIMER OF IMPLIED WARRANTIES
This limited warranty is in lieu of all other expressed or implied warranties, including any warranty of FITNESS FOR A PARTICU-
LAR PURPOSE OR USE and any implied warranty of MERCHANTABILITY otherwise applicable to this product. ECHO, INC. and its affiliated companies shall not be liable for any special incidental or consequential damage, including lost profits. There are no warranties extended other than as provided herein. This limited warranty may be modified only by ECHO, INC.
X7561120400
8/15
P
roduct
r
egistration
Thank you for choosing Shindaiwa Power Equipment
information will never be sold or misused by ECHO, Inc. Registering your purchase enables us to contact you in the unlikely event of a service update or product recall, and verifies your ownership for warranty consideration.
25
NOTES
26
NOTES
27
Servicing Information
Parts/Serial Number
Genuine Shindaiwa Parts and Assemblies for your Shindaiwa products are available only from an Authorized
Shindaiwa Dealer. When you do need to buy parts always have the Model Number, Type and Serial Number of the unit with you. You can find these numbers on the engine. For future reference, write them in the space provided below.
Service
Service of this product during the warranty period must be performed by an Authorized Shindaiwa Service Dealer.
For the name and address of the Authorized Shindaiwa Service Dealer nearest you, ask your retailer or call: 1-877-
986-7783 . Dealer information is also available on WWW.SHINDAIWA.COM. When presenting your unit for Warranty service/repairs, proof of purchase is required.
Consumer Product Support
If you require assistance or have questions concerning the application, operation or maintenance of this product you may call the SHINDAIWA Consumer Product Support Department at 1-877-986-7783 from 8:00 am to 5:00 pm (Central Standard Time) Monday through Friday. Before calling, please know the model and serial number of your unit.
Warranty Registration
To ensure trouble free warranty coverage it is important that you register your SHINDAIWA equipment on-line at
WWW.SHINDAIWA-USA.COMor by filling out the product registration sheet included in this manual. Registering your product confirms your warranty coverage and provides a direct link between you and ECHO if we find it necessary to contact you.
Additional or Replacement Manuals
Replacement Operator and Parts Catalogs are available from your Shindaiwa dealer or at WWW.SHINDAIWA.
COM or by contacting the Consumer Product Support Department (1-877-986-7783). Always check WWW.SHINDAI-
WA.COM for updated information.
ECHO Incorporated.
400 Oakwood Road
Lake Zurich, IL 60047-1564 U.S.A.
Telephone: 1-877-986-7783
Fax: 1-847-540-8416 www.shindaiwa.com
Copyright© 2016 By Echo, Incorporated
All Rights Reserved.
Yamabiko Corporation
7-2 Suehirocho 1-Chome, Ohme,
Tokyo, 198-8760, Japan
Phone: 81-428-32-6118
Fax: 81-428-32-6145
S95713001001/S95713999999
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement