Kaiser Fototechnik MonoCR-C2 Datasheet

PDF

Έγγραφο

Διαφήμιση

9084_DigitalZub_GB_1012_DigitalZub_9084_GB_0812 23.10.12 11:31 Seite 2

TWIN1: Not

TWIN1 R3/R4

The Wireless and

Wired Remote Release for Your Camera

Twin1 R4 Infrared Transmitter/Receiver Kit

Transmitter

- Applicable as an IR remote shutter release and cable release (for exceptions see survey below)

- Working range up to 100 m (330 ft.) with separate receiver, 50 m (165 ft.) (Nikon, Pentax, Samsung) or 25 m

(82 ft.) (Canon) with cameras with built-in receiver

- Two-step release button, delay shot

(wireless) and bulb shot mode

- Built-in flashlight LED

- Includes 1 m (39 in.) release cable

TWIN1 R4 receiver

(except for 6167)

- Streamlined design

- Two red LEDs for release control

- Size: 30 x 40 x 25 mm (1.2 x 1.6 x 1 in.)

TWIN1 R4N receiver

(6167)

- Extremely small and light-weight (6 g / 0.2 oz.)

- Red LED for release control

- Powered by camera, needs no extra battery

- Size: 15 x 15 x 22 mm (0.6 x 0.6 x 0.9 in.)

R4N

6167

Twin1 R3

Transmitter only (similar to R4) for cameras which are already equipped with a build-in IR receiver. Release cable included.

Working range up to 50 m (165 ft.) with Nikon,

Pentax and Samsung cameras, up to 25 m (82 ft.) with Canon cameras.

Product Survey

Canon: 1D, 1D Mark II, 1D Mark IIN, 1D Mark III, 1D Mark IV, 1DS, 1DS Mark II,

1 DS Mark III, 5D, 5D Mark II, 5D Mark III, 7D, 10D, 20D, 30D, 40D, 50D, D30, D60

Canon: 1000D, 1100D, G12, Samsung: NX 5, NX 10, NX 11, NX 100, Sigma: SD14

Canon: 300D, 350D, 400D, 450D, 500D, 550D, 600D, 650D, 60D, Samsung: GX-1L,

GX-1S, GX-10, GX-20, Pentax: *istD, *istDs, *istDs2, *istDL, *istDL2, K-5, K-7, K10D, K20D,

K30D, K100D, K110D, K200D

Canon (IR only, no accessory terminal): EOS M, Pentax (IR only, no accessory terminal): K-m, K-x, K-r

Nikon: D1, D1X, D1H, D2, D2H(s), D2X, D2Xs, D3(s), D3X, D4, D200, D300, D300s,

D700, D800, D800E, Fuji: S5pro, S3pro

Nikon: D90, D3200, D5000, D5100, D7000

Nikon (IR only, no accessory terminal): D40(x), D50, D60, D70, D70s, D80, D3000, V1, J1,

Coolpix P7100

Nikon: D3100

Sony: Alpha 33, 35, 37, 55, 65, 77, 100, 200, 300, 350, 450, 500, 550, 580, 700, 850, 900,

Minolta: 5D, 7D

Panasonic: G1, GH1, GF1, G2, GH2, G3, G5, GX1, G10, FZ 20, FZ 30, FZ 50, FZ 100,

FZ 150, FZ200, LC1, L10, L1, Leica: Digilux 2/3, V-Lux 1/2/3

Olympus: Pen E-P1, Pen E-P2, Pen E-PL2, Pen E-P3, Pen E-PL3, Pen E-PM1; E-30, E-620,

E-520, E-510, E-420, E-410, SP-510UZ, SP-550UZ, SP-560UZ, SP-565UZ, SP-570UZ,

SP-590UZ, SP-810UZ, XZ-1, SZ-30MR, SZ-20, SZ-11, OM-D E-M5

Twin1 R3

System

6161

6162

Twin1 R4

System

6169

6168

6167

(R4N)

6171

6161

Twin1 RF

System

6178

6177

MonoCR

System

6188

6187

6177

6179

(RFN)

6180

6181

6187

6189

6190

6191

6192

6193

9084_DigitalZub_GB_1012_DigitalZub_9084_GB_0812 23.10.12 11:31 Seite 3

t Only for Immediate Release

TWIN1 RF

The Radio-Controlled

Wireless and Wired

Remote Release

Twin1 RF transmitter

- Applicable as an RC remote shutter release and cable release

- Working range up to 100 m

(330 ft.)

- Two-step release button, delay shot

(wireless) and bulb shot mode

- Built-in flashlight LED

- Operation frequency: 2.4 GHz

- Size: 88 x 26 x 17 mm, 19 g

(3.5 x 1 x 0.7 in, 0.7 oz.)

- Includes 1 m (39 in.) release cable

6177

Twin1 RFN receiver

(6179)

- Extremely small and light-weight

(6 g / 0.2 oz.)

- Red LED for release control

- Powered by camera, needs no extra battery

- Size: 15 x 15 x 22 mm (0.6 x 0.6 x 0.9 in.)

RFN

Twin1 RF receiver

(except for 6179)

- Streamlined design

- Two red LEDs for release control

- Size: 30 x 40 x 25 mm (1.2x1.6x1 in.)

6179

Product survey: see table on previous page.

6178

MonoCR – The Cable Release for

Your Camera

This compact and ergonomically shaped cable release is very similar to your camera’s release button. Most useful in macro photography, when using large telephoto lenses or for long exposures, a cable release ensures vibration-free shooting.

Two-step release: At the first pressure point TTL metering and auto focus is activated, the second triggers the shutter.

For bulb shots the button can be locked

(color indicator).

The release cable can be detached and extended using the 2 m (6.6 ft.) extension cable (code no. 6185).

Length of coiled cord (extended): approx. 90 cm (35.4 in.)

Dimensions: approx. 105 x 34 x 23 mm

(4.1 x 1.3 x 0.9 in.)

Weight: approx. 30 g (1.1.oz.)

Product survey: see table on previous page.

6187-93

6180 6181

9084_DigitalZub_GB_1012_DigitalZub_9084_GB_0812 23.10.12 11:31 Seite 4

TWIN1 ISR -

The Multifunctional

Remote Shutter Release

• for interval exposure

• for long exposure

• for timer-controlled exposure

• for continuous shooting

Release button lock

Set up button Illumination button

Navigation button

Enter button

Release button

Display panel

Cable connection port

Battery cover

Interval timer icon

Timer icon

Operation run indicator

Battery-low icon

Hold indicator

Display mode

Delayed start is supported. Timer and interval time ranges from 1 second to 99 hours,

59 minutes, 59 se conds. Exposure numbers range from 1 to 9.999. 4-way-operation button. All buttons can be locked to prevent unintentional operation. Beep sound can be switched off. Low battery warning. Normal shutter release can be used without a battery fitted, all other functions require a battery.

- Battery: 3V (CR 2032)

- Operating time: approx. 2 months

- Release cable length: approx. 1 m (39 in.)

- Size: 23 x 16 x 100 mm (0.9 x 0.6 x 3.9 in.)

- Weight: 26 g / 0.9 oz. (incl. batteries)

Exposure count icon

Exposure time icon

Beep sound On/Off icon

Time indicator

Product Survey

6131 Twin1 ISR iC, for Canon 1000D,

1100D, 650D 600D, 550D, 500D,

450D, 400D, 350D, 300D, 50D,

40D, 60D, 30D, 20D,10D, 7D, 5D

(Mark II/III), 1Dx, 1D(s) Mark

II(N)/III/IV, 1D(s), G12, D30, D60,

Pentax K200D, K110D, K100D, istD..., K20D, K10D, K7, K5,

Samsung GX-.., NX 5, NX 10,

NX 11, NX 100, Sigma SD14

6133 Twin1 ISR iN, for Nikon D7000,

D3200 , D3100, D5100, D5000,

D90, D80, D70s, D700, D800,

D800E, D300(s), D200, D4, D3(x),

D3(s), D2, D2H(s), D2X(s), D1,

D1H, D1X, Fuji S3Pro, S5Pro

6134 Twin1 ISR i04, for Sony Alpha 33,

35, 37, 55, 65, 77, 100, 200, 300,

350, 450, 500, 550, 580, 700, 850,

900, Minolta 5D, 7D

6135 Twin1 ISR i07, for Leica Digilux 2/3,

V-Lux1, V-Lux2/3, Panasonic GX1, G1,

G2, G3, G10, GH2, FZ100, FZ150,

FZ20, FZ30, FZ50, L1, L10, LC1

Exposure count icon

Set up icon

Illuminated triple-spaced LCD.

Three types of display mode.

Easy user interface for all settings.

9084_DigitalZub_GB_1012_DigitalZub_9084_GB_0812 23.10.12 11:31 Seite 5

More to Release!

TWINLINK T2D:

A Combined

Radio Frequency and Infrared

Flash Trigger

• two simultaneous triggering sig nals for high operational reliability

• for studio and camera flash systems

Set comprising transmitter and receiver for wireless triggering of studio and camera flashguns.

Simultaneous triggering via 2.4 GHz radio frequency and infrared signals using eight high performance LEDs. 16 user selectable channels.

Transmitter and receiver with LED panels that can be illuminated and external aerials. Automatic power off after pre-determined time.

Transmitter can be attached using the camera's hot shoe or with an adhesive accessory shoe mount attached in a convenient location. Recei ver with tripod thread and mounting magnets for attachment to metal surfaces or via an adhesive metal plate supplied with the set. Receiver has a hot shoe and trigger cable terminals for PC and

2.5 mm jack-plug. Battery or mains operation.

- Max working range: approx. 50 m (165 ft.) indoors, approx. 200 m (660 ft.) outdoors.

- Max. sync. speed: 1/250 sec. (depending on camera and flash)

- Batteries: Transmitter: 2x CR 2032, receiver:

3 x AAA (primary or rechargeable)

- External power supply: Mains adapter/charger for receiver only (will also charge rechargeables).

- Dimensions: Transmitter: 40 x 68 x 35 mm

(1.6 x 2.7 x 1.4 in.), Receiver: 50 x 80 x 25 mm (2 x 3.1 x 1 in.)

- Weight: Transmitter: 35 g (1.2 oz.), Receiver:

53 g (1.9 oz.)

Remote Flash Trigger

Product survey

6140 TwinLink T2D

Receiver and transmitter. Includes

PC cable, 2.5/3.5 receiver cable,

3.5/6.3 adapter plug, adhesive accessory shoe, adhesive metal plate, AC power adapter, 3 AAA batteries, 2 CR 2032 batteries, receiver fixture clip

6141 TwinLink T2RxD

Additional receiver for TwinLink T2D

1503

1504

For wireless lag-free firing of a second flash unit. Range up to 20 m (65.6 ft.) depending on the guide number of the flash unit and room brightness. 1/4" tripod bush. Features an additional PC flash terminal to connect another flash unit.

1503: For flash units with standard ISO foot

1504: For flash units with 4-pin Sony/Minolta foot

9084_DigitalZub_GB_1012_DigitalZub_9084_GB_0812 23.10.12 11:31 Seite 6

Simply More

Options – Flash

Accessories

Flash Adapter

For firing flash units with standard ISO foot and center contact mounted on a

Sony/Minolta DSLR camera with proprietary 4-pin foot.

Features an additional PC flash terminal to connect another flash unit.

1304

1000

Flash Bracket

Light metal bracket with resilient contact surface.

Length: 16.5 cm (6.5 in.)

1107

Angle Bracket

Collapsible. Stable threepoint rest.

1200

Bounce Flash Shoe

For indirect flash illumination. Steplessly adjustable.

Height: 45 mm (1.8 in.).

Mounting Foot

With accessory shoe for lighting units, flash guns etc. Tripod thread

1/4" for attachment on tripods. Dimensions:

94 x 63 x 11 mm (3.7

x 2.5 x 0.4 in.)

6040

1300

Flash Shoe Adapter

For cameras with hot flash shoe and flash equipment without hot flash shoe.

With synchro flash socket.

1301

Flash Shoe Adapter

For cameras without hot flash contact and flash equipment with hot flash contact. With synchro cable.

1303

Flash Adapter

For connecting flash guns to receivers of RC remote releases, e.g.

Kaiser TwinLink, Pocket

Wizard, Skyport etc.

1407

PC-PC Flash Cable

With male PC plug at both ends to connect flashguns. Length: 5 m

(16.4 ft.)

1420: 0,5 m

1423: 2 m

1405

PC-PC Spiral Cord

With male PC plug at both ends to connect flashguns. Length:

65 cm (25.6 in.)

1322

Triple PC Flash Outlet

For simultaneous use of up to three flash units with standard PC plugs.

1409

Flash Cable

With pull relief. 10 m

(33 ft.). PC plug and jack plug ø 6.35 mm.

1450

Spiral Cord

For connecting flash equip ment and as extension cord. 2 m

(6.6 ft.), PC plug - PC socket.

1424: 3 m

1425: 5 m

1426: 10 m

Extension Cord

For connecting flash equipment. With right-angle plug and socket (PC).

1215

Accessory Shoe Adapter

For cameras with Sony/

Minolta flash shoe.

Sony/Minolta c Standard/ISO

9084_DigitalZub_GB_1012_DigitalZub_9084_GB_0812 23.10.12 11:31 Seite 7

This? . . .or That?

„digiShield“ LCD Glare Shield

• digiShield shields lateral and angular incidence of light from the LCD monitor and improves the visibility of the monitor image.

• digiShield folds down completely and serves also as a cover and a screen protector.

• digiShield fits almost all digital compacts and is attached to the tripod socket.

• digiShield is available for 2.7” (digiShield

) and 3.0” LCDs (digiShield

) in silver and in black.

• digiShield has coil spring supported side flaps which open automatically.

• digiShield

3 flips up completely to ease the operation of touch screen LCDs.

6074 6054

Screen size

(diag.):* 2.7” (6.9 cm) 2.7” (6.9 cm)

Designation: digiShield 2 digiShield 2

Colour: silver black

* eventually minor border covering with 6.9 cm (2.7”)

6075 6055

3.0” (7.6 cm) 3.0” (7.6 cm) digiShield 3 digiShield 3 silver black

6054

6074

6075

. . .or This!

SL3 LCD Loupe

The SL3 LCD loupe has been designed for DSLRs and CSCs with 3” LCD. It is not only a perfect shield against incident light, but enables, in any ambient light situation, an optimal examination of frame and focus while shooting and during playback. The built-in loupe has a double-side coated lens element with 2.3 magnification and diopter adjustment.

Attaches to the camera via selfadhesive mounting frame where the hood clicks into place.

Eyecup can be positioned for left or right eye viewing.

6084

9084_DigitalZub_GB_1012_DigitalZub_9084_GB_0812 23.10.12 11:31 Seite 8

Lens Hoods

Designed for the lenses of digital SLRs. Fits onto the matching lens facing either forward for normal use or rearwards for storage (except 6887, mounts onto filter thread). Made of impactresistant plastic.

NEW 6866: CT67, for Canon

EF 100/2.8 USM/Macro USM

NEW 6868: CT73, for Canon

EF 100/2.8 L Macro IS USM

NEW

6869: CT73B, for Canon EF 70-

300/4-5.6 L IS USM, white

NEW

6870: CT74, for Canon EF 70-

200/4.0 L (IS) USM, white

NEW 6871: CT83C, for Canon EF 100-

400/4.5-5.6 L IS USM, white

NEW 6873: CT87, for Canon EF 70-

200/2.8 L IS II USM, white

NEW

6874: CW83F, for Canon

EF 24-70/2.8 L USM

NEW

6875: CW83G, for Canon EF 28-

300/3.5-5.6 L IS USM, white

NEW 6876: CW83H, for Canon

EF 24-105/4.0 L IS USM

NEW

6878: CW88, for Canon

EF 16-35/2.8 L II USM

You

Must

Have This!

NEW

6879: C78E, for Canon EF-S 15-

85/3.5-5.6 IS USM

6880: C60, for Canon

EF 28-90/4.0-5.6 II (USM),

EF 28-80 (II/USM),

EF-S 18-55/3.5-5.6 IS (USM/II),

EF 22-55/4.0-5.6

6881: C73, for Canon

EF 24-85/3.5-4.5 (USM)

6882: C78, for Canon

EF 28-135/3.5-5.6 IS USM

6883: C71, for Canon

EF 50/1.4 USM

6884: C65III, for Canon

EF 85/1.8 (USM),

EF 100/2.0 USM,

EF 135/2.8 soft focus,

EF 70-210/3.5-4.5 USM,

EF 100-300/4.5-5.6 (USM)

6885: C65B, for Canon EF 70-

300/4.5-5.6 DO IS USM,

EF 70-300/4.0-5.6 IS USM

6886: C67B, for Canon

EF-S 60/2.8 Macro USM

6887: C62, for Canon EF 50/1.8 II

6888: C60T, for Canon EF 75-

300/4.0-5.6 III (USM),

EF 90-300/4.5-5.6 (USM),

EF-S 55-250/4.0-5.6 IS

6889: C73B, for Canon EF-S 17-

85/4.0-5.6 IS USM,

EF-S 18-135/3.5-5.6 IS (STM)

6890: C78D, for Canon

EF-S 18-200/3.5-5.6 IS,

EF 28-200/3.5-5.6 (USM)

6891: C83, for Canon

EF-S 10-22/3.5-4.5 USM,

EF 17-40/4.0L USM,

EF 16-35/2.8L USM (old version)

6892: C83J, for Canon

EF-S 17-55/2.8 IS USM

6893: N32, for Nikon AF-S DX 18-

70/3.5-4.5G IF-ED,

AF-S 18-105/3.5-5.6 G ED VR,

AF-S 18-135/3.5-5.6 IF-ED

6894: N45, for Nikon AF-S DX 18-

55/3.5-5.6G ED/EDII/VR

6895: N37, for Nikon AF-S NEW

DX 55-200/4.0-5.6G ED VR

6899: SH108, for Sony DT

18-55/3.5-5.6 SAM

NEW

Lens Hoods for Pancake Lenses

3-in-1

Lens Hoods

for lenses with 28 to 200 mm focal length (35 mm equivalent).

Made of matte black rubber, foldable. With light baffles. Metal screw-in mount. Filter thread.

Wide angle

6820: ø 49 mm

6821: ø 52 mm

6822: ø 55 mm

Standard

6823: ø 58 mm

6824: ø 62 mm

6825: ø 67 mm

Telephoto

6826: ø 72 mm

6827: ø 77 mm

Made of matte black rubber. Rotating connecting ring with metal mount and locking screw.

Includes lens cap for use with mounted lens hood.

6829: For Panasonic Lumix G with 1.7/20 mm or 2.5/14 mm

Pancake lens, also for JVC and Panasonic camcorders with

46 mm filter thread.

6831: For Olympus Pen with M.Zuiko Digital 2.8/17 mm Pancake lens, M.Zuiko Digital 3.5-5.6/14-42- mm II, Panasonic

Lumix G X Vario PZ 14-42 mm 3.5-5.6, also for Canon,

JVC and Sony camcorders with 37 mm filter thread.

9084_DigitalZub_GB_1012_DigitalZub_9084_GB_0812 23.10.12 11:32 Seite 9

Protective Shield:

Screen Protectors for the

Camera LCD

Anti-Reflective Screen Protective Film

High-quality film for use with digital cameras. Protects the screen from scratches, dirt and fingerprints. Glare-free by

anti-reflective layer. Has UV protection and hard coating, optimized for touch-screens.

Attaches by adhesion due to silicon coating.

Easy to apply, no bubbling. Can be removed without residues. 1 piece.

6085: for 6,4 cm (2,5“) screens

6086: for 6,9 cm (2,7“) screens

6087: for 7,6 cm (3,0“) screens

6090: for 8,9 cm (3,5“) screens

6092: for 10,2 cm (4,0“) screens

Format 16:9

6095: for 7,6 cm (3,0“) screens

6097: for 8,9 cm (3,5“) screens

Also available custom-fit for these digital SLRs and CSCs:

6615: for Canon 50D / 40D *

6616: for Canon 7D *

6618: for Canon 60D / 600D

6619: for Canon 1100D

6623: for Nikon D300(s) *

6625: for Nikon D3100

6626: for Olympus E450 / E420 / E520

6627: for Olympus E620

6628: for Panasonic G3 / GF3 / GF5 / GX1

6629: for Panasonic TZ18 / 22 / 25 / 31,

Leica V-Lux 30 / 40, Nikon P510

6630: for Panasonic GH1 / G1

6631: for Panasonic GF1 / GF2 / FZ45 /

LX5 / LX7, Leica D-Lux 5

6632: for Panasonic GH2 / G2 / FZ100,

FZ150, Leica V-Lux 2 / 3

6634: for Sony Alpha 230 / 290 / 450

6636: for Sony Alpha 500 / 550

6637: for Sony Alpha 580

6638: for Sony Alpha 33 / 35 / 55 und

NEX 3 / C3 / 5 / 5N / 7 / F3

6640: for Sony Alpha 57 / 65 / 77,

DSC-HX200 NEW

6642: for Olympus OM-D E-M5

6644: for Nikon D3200

6645: for Nikon D7000 *

6646: for Nikon D5100

6647: for Nikon 1 J1

NEW

6648: for Nikon 1 V1, Fujifilm HS 30

6649: for Nikon D800 *

NEW

6650: for Canon 5D Mark III

6651: for Canon 650D

NEW

UV protection

No color tint

Scratch resistent

Touch optimised

Effective adhesion

Removable, no residues

Bubble-free application

„Standard“ LCD Screen Protective Film

Antireflection

Hardcoat

UV filter

PET

Silicon

Backing layer

* includes protective film for control panel

„Crystal Clear“ Screen Protective Film

High-quality clear film for use with digital cameras. Protects the screen from scratches, dirt and fingerprints. High level of transpa-

rency, hardly visible. Has UV protection and hard coating, optimized for touch-screens. Attaches by adhesion due to silicon coating.

Easy to apply, no bubbling. Can be removed without residues.

1 piece.

6079: for 6,9 cm (2,7“) screens

6080: for 7,6 cm (3,0“) screens

6081: for 8,9 cm (3,5“) screens

6082: for 10,2 cm (4,0“) screens

Format 16:9

6093: for 7,6 cm (3,0“) screens

6094: for 8,9 cm (3,5“) screens

6078

For use with digital cameras, mobile phones and PDA's

(6076 also for GPS). Protects the screen from scratches, dirt and fingerprints. Also for touch-screens. Can be removed without residues

6076: Set with three 4 x 3" (10 x 8 cm) sheets each, with cutting lines for required size. Comes with cleaning cloths and a squeegee card to apply the film.

6078: For 3" LCD screens. Can be cut to fit smaller screens. Rounded corners. 3 pieces.

9084_DigitalZub_GB_1012_DigitalZub_9084_GB_0812 23.10.12 11:32 Seite 10

Even More for Your Lens

ø 34 mm

ø 37 mm

ø 39 mm

ø 40,5 mm

ø 43 mm

ø 46 mm

ø 49 mm

ø 52 mm

ø 55 mm

ø 58 mm

ø 62 mm

ø 67 mm

ø 72 mm

ø 77 mm

ø 82 mm

ø 86 mm

ø 95 mm

Rodenstock „HR Digital super MC“ and

„Digital pro MC“ Filters

Both these Rodenstock filter series are made from tempered glass with highest possible surface quality and are also highly scratch-resistant.

Their flat slimline mounts prevent vignetting with wide-angle lenses. The front thread allows the use of a lens hood or of the lens cap with the filter in place.

The filter mount of the less expensive Digital pro MC series is made from tempered, black anodized aluminum and is quite lightweight.

The filter mount of the HR Digital super MC series is made from robust brass for optimum smooth movement of both threads. An additional water and oil repellent coating provide for the so-called lotus effect.

Rodenstock UV Filters

Rodenstock UV blocking filters block out the

UV radiation exactly at the border to visible light. This is extremely efficient and they are perfectly color neutral.

17734

17737

17740

17743

17746

17749

17752

17755

17758

17762

17767

17772

17777

17782

17937

17939

17940

17943

17946

17949

17952

17955

17958

17962

17967

17972

17977

17982

17986

17995

Due to the perfect color neutrality Rodenstock

UV blocking filters are also ideal protective filters that can be left on the lens at all times.

Rodenstock Circular Polarizing Filters

Circular Polarizers reduce or eliminate reflections on surfaces, reduce the diffuse blue cast in landscape photographs and produce an improved color saturation.

17855

17858

17862

17867

17872

17877

17882

17849

17852

18049

18052

18055

18058

18062

18067

18072

18077

18082

18086

18095

NEW

18249

18252

18255

18258

18262

18267

18272

18277

18282

NEW

18449

18452

18455

18458

18462

18467

18472

18477

18482

Rodenstock Neutral Density Filters ND 2x, 4x, 8x

They allow the extension of exposure times by a factor of 2, 4 or 8 for impressive smear effects or a further opening of the aperture for a con sider ably reduced depth of field.

Rodenstock Variable Neutral Density Filter

If more than the fixed 2x, 4x and 8x ND levels or a finer graduation is required, the Digital

Vario MC variable neutral density filter is the right solution.

NEW

18849

18852

18855

18858

18862

18867

18872

18877

18882

NEW

18949

18952

18955

18958

18962

18967

18972

18977

18982

Camera Body Caps Lens Rear Caps „Snap-On” Lens Caps

6521: for Canon EOS

6522: for Minolta MD

6523: for Sony/Minolta AF

6525: for Nikon

6527: for Pentax K-Bajonett

6528: for Micro Four Thirds NEW

6531: for Canon EOS

6532: for Minolta MD

6533: for Sony/Minolta AF

6535: for Nikon

6536: for Olympus OM

6537: for Pentax K-Bajonett

6538: for Micro Four Thirds

NEW

Reliable hold by clamp-on design. Includes loss protection. Can also be used with lens hood mounted.

6845: ø 37 mm

6847: ø 43 mm

6848: ø 46 mm

6833: ø 49 mm

6835: ø 55 mm

6836: ø 58 mm

6837: ø 62 mm

6838: ø 67 mm

6840: ø 77 mm

6841: ø 82 mm

6842: ø 86 mm

6834: ø 52 mm 6839: ø 72 mm

9084_DigitalZub_GB_1012_DigitalZub_9084_GB_0812 23.10.12 11:32 Seite 11

You Should

Have This!

ProDisk

Combination of white balance, grey card and colour reference in a slim, foldable plastic housing. Colour card and grey card located in lower and upper covers. Translucent, white balance filter with special surface pattern in centre.

Includes neck strap.

6601: ProDisk mini

White balance filter for lenses up to 6 cm

(2.4 in.) diameter.

Dimensions

(folded down):

103 x 73 x 10 mm

(4.1 x 2.9 x 0.4 in.), weight: 75 g (2.6 oz.)

6602: ProDisk II

White balance filter for lenses up to 9 cm

(3.5 in.) diameter.

Dimen sions

(folded down):

145 x 101 x 11 mm

(5.7 x 4.0 x 0.4 in.), weight: 135 g (4.8 oz.)

„Vivicap“ White Balance Filter

Snap-on filter with specially designed prism structured surface for white-balancing of digital cameras and camcorders. Easy to use clamping mechanism provides for quick installation and removal. Serves also as a lens cap and can also be attached when a lens hood is used.

6605: ø 52 mm

6606: ø 55 mm

6607: ø 58 mm

6608: ø 62 mm

6609: ø 67 mm

6610: ø 72 mm

6611: ø 77 mm

Digital Slide Duplicator

Suitable for digital cameras with filter thread. Connecting thread 52 mm.

With detachable achromatic macro lens. Full size copy can be obtained using it with a lens with focal length of 80 – 120 mm, details with higher focal length. Includes holder for two slides and 58-52 mm adapter ring.

Film Strip Carrier

For six 35mm negatives or unmounted slides. For use with

Slide Duplicator

6506.

6507

6506

9084_DigitalZub_GB_1012_DigitalZub_9084_GB_0812 23.10.12 11:32 Seite 12

Modern Tripods with a History:

T iltall tripods have been on the market since 66 years – but this is another story, that can not be told now.

Here are the facts for today’s Tiltall tripods.

• 180 degrees reversible legs for reduced pack size

• One tripod leg is detachable and can be converted to a monopod by adding the removable center column.

• Reversible center column for macro shots. Center column can also be removed for close-to-ground level-setting.

• Four-section tripod legs with anti-twist protection and twist locks for fast and easy operation.

• Spread angle of legs can be individually adjusted and locked in three positions, covered ratchet toothing with release button.

• Extendable center column with anti-twist device, twist lock and spring loaded hook.

• Rubber feet with retractable metal spikes made from stainless steel.

• 1/4” – 3/8” interchangeable thread.

• Eight-layer carbon fibre, reduced weight, very good vibration absorption

(6069-6071) or aircraft aluminum respectively.

• Padded carrying case with adjustable and detachable shoulder strap, carry handle and inside tool pocket.

• All tripod legs with leg warmers for isolation against cold.

Code no.

6066 6067 6068

Type TE-224 TE-254 TE-284

Material Alu

Tube-ø, max. (mm) 22

Max. height (cm) 140

Min. height (cm) 14

Pack size (cm) 40

Alu

25,5

147

Alu

162

Monopod height 65-142 71-152 78-169

Weight (kg) 1,1 1,4 1,8

Max. load (kg) 8 8 12

Recommended BH-10 BH-20 BH-30 ball head (6001) (6002) (6003)

6069 6070 6071

TC-224 TC-254 TC-284

Carbon Carbon Carbon

22 25,5 29

140

147

162

65-142 71-152 78-169

0,9 1,1 1,4

8 8 12

BH-10 BH-20 BH-30

(6001) (6002) (6003)

Tiltall Ball Heads

• Solid ball head with dovetail clamping for quick-release plates.

• Quick-release plate with non-slip surface, detachable slide-off protection and 1/4" D-ring screw with coin slot.

• Two spirit levels for exact alignment.

• Adjustable friction.

• 360 degree panning socket with blocking screw and graduated scale.

• 3/8” tripod bush.

• Quick-release plates are also available individually.

Code no.

6001 6002 6003

Typ BH-10 BH-20 BH-30

Ball diameter (mm) 30 36 44

Socket diam. (mm) 45 51 60

Height (mm)

Weight (g)

Max. load (kg)

360

440

107

570

Monopod

Compact and sturdy Tiltall monopod made from aircraft aluminum.

Quick set-up by simultaneous opening of all three twist locks. Four sections with anti-twist protection, rubber foot with retractable metal spike, foam rubber leg warmer protects against cold, convenient wrist strap. Carry bag included.

Max. height: 160 cm

Pack size / min. height: 51 cm

Exchangeable threads: B 1/4 / B 3/8

Max. load: 11 kg

Code no. 6060

9084_DigitalZub_GB_1012_DigitalZub_9084_GB_0812 23.10.12 11:32 Seite 13

Fits All!

5534

Camera Mounting Platform

For precise camera adjustment for close-up, macro and copying.

6020

Quick-Release Connector

For quick mounting of camera on tripod.

6011

Pro Ball-and-Socket Head

With adjustable friction brake and pa norama base. Weight 650 g

(1.4 lbs.), height 123 mm (4.8 in.), base diameter 56 mm (2.2 in.), max. load 8 kg (17.6 lbs.).

6017 6018 6013

Ball-and-Socket Head

Rotating panorama base.

Weight 300 g (10.6 oz.), height 98 mm (3.9 in.), base diameter 45 mm (1.8 in.), max. load 4 kg (8.8 lbs.).

Ball-and Socket Head

Weight 110 g (3.9 oz.), height 67 mm (2.6 in.), base diameter 30 mm

(1.2 in.), max. load

2 kg (4.4 lbs.).

Ball-and Socket Head

Weight 45 g (1.6 oz.), height 50 mm (2 in.), base diameter 24 mm

(1 in.), max. load 1 kg

(2.2 lbs.).

6024

Quick Release Connector

Plate

Fits 6020.

High-Level Meeting: Spirit Levels:

Analogue and Digital

6386

Spirit Level with circular bubble, self-adhesive. Can also be screwed on.

6380

Duplex Screw-In

Spirit Level

Mounts in between camera and tripod.

6385

Spirit Level

One level each for vertical and horizontal shooting position. With moun ting shoe and 1/4” tripod bush.

6387

Duplex Spirit Level

With twin levels and mounting feet for landscape and portrait position.

Action Level

Digital spirit levels for use in portrait and landscape formats using

LEDs of different colors for indication. Especially useful for levelling the camera at night, at a high position for over-head shots and in all situations where a traditional spirit level would be difficult or impossible to see.

Brightness and sensitivity can be adjusted (from +/- 0.2°). Fits into standard hot shoe.

Supplied with additional magnetic pedestal for attaching on other flat surfaces.

Action Level Sound

With beep sounds for indication (can be switched off). Compact design.

Does not interfere with most camera´s pop-up flash. 32 x 25 x 17 mm

(1.3 x 1 x 0.7 in.), weighs only 5 grams.

6383

Action Level Cross

Cross indicator with 13

LEDs for simultaneous two-dimensional indication. Additional 7 LED side level indicator. Diameter approx. 32 mm (1.3 in.), weighs only 6 grams.

6378

9084_DigitalZub_GB_1012_DigitalZub_9084_GB_0812 23.10.12 11:32 Seite 14

Quik Pod - for Snapshots at Arm’s

Y our arm is too short? Quik Pod can help – no matter whether you will take a picture of yourself or just want to shoot over the head of crowds. Quik Pod will give your arm 46 cm (18 in.) of additional length,

Length

will convert to a table top tripod and is ready to become your all-time companion.

Quik Pod is an extendable hand-held tripod for cameras and camcorders. It has a lockable ball head, a camera support with 1/4” tripod thread and a small mirror showing you roughly what the camera will see. It is easy to extend and to retract.

Specifications

Length (extended): approx.

46 cm (18 in.) (retracted): approx. 19 cm (7.5 in.)

Weight: approx. 100 g

(3.5 oz.)

Max. load: 450 g (16 oz.)

Kit includes pocket clip, hiking clip, wrist strap, tripod legs and carrying bag.

Code no. 6046

Quik Pod DSLR

Q uik Pod DSLR is a handheld tripod and a monopod. It extends your reach even more and takes a higher load.

Small – But

Going Strong

T able top tripods are extremely compact, but provide a firm support.

• Made of high quality polycarbonate and aluminium • Extends up to

135 cm (53 in.) • For digital SLRs, camcorder and lights • Retracted size 47 cm (18.5 in.) • Weight 270 g

(8.9 oz.) • Quik release platform

• 1/4“ tripod thread • Max. load: 2 kg / 4.4 lbs.

(handheld tripod), 3.5 kg /7.7 lbs. (monopod).

Kit includes monopod foot, belly pad, hiking clip, wrist strap and carrying bag. Code no. 6047

6045

6043

DSLR Table Top Tripod

With three-section telescopic legs and extendable center column. 3-way pan head with tiltable camera platform.

Height: 18-30 cm (7.1-11.8 in.), folded length: 21 cm (8.3 in.).

6044

Multi-Level Table Top Tripod

Height continuously adjustable, three-section telescopic feet, folds-down to compact size. Ball head with locking screw (6043) or with pan and tilt head (6044).

Small Table Top Tripod

Extendable telescopic feet, folds down flat. Ball and socket head with locking screw. Titanium coloured.

6037

9084_DigitalZub_GB_1012_DigitalZub_9084_GB_0812 23.10.12 11:32 Seite 15

Keep It Clean

702002

K inetronics’ SpeckGRABBER Pro SGP (702002) removes individual particles of dust and dirt from sensitive surfaces without damaging them. Suitable for cleaning camera sensors (manufacturers instructions must be followed), SLR mirrors, lenses and oculars, films, slides, etc. With rubber-coated handle.

702004

SpeckGRABBER Pro Kit SGL

With integrated mini lamp, three tips, cleaning solution and anti-static cloth in robust box.

702005

SpeckGRABBER Pro Kit SGK

With SpeckGRABBER Pro handle, three tips, cleaning solution and anti-static cloth in robust box.

702001

SpeckGRABBER SG

With standard handle.

706518 700010

700001

Anti-Static Micro-Fibre Cloth

Specially conductive fibres,

700001 for dry cleaning,

706518 for wet cleaning.

700030

Anti-Static-Brushes

For sensitive surfaces.

700010: width 10 mm

700020: width 20 mm

700030: width 30 mm

6309/10

6301

Lens Brush

In plastic tube. Lipstick twist mechanism.

6308

"Clear Gear" Compressed Air

For touch-free dust removal.

707025

ECK Optical Cleaning Set

With anti-static cloth 13 x

14.5 cm (5.1 x 5.7 in.) and

6 ml (0.2 oz.) of cleaning solution in a drop bottle.

707001

Outdoor Photographer's

Optical Cleaning Kit

Cleaning solution, antistatic cloth and brush,

SpeckGRABBER SG, Swabs.

„Typhoon Blower“

Blower Bellows

Large rubber bulb for strong blowing effect. Rugged front air nozzle, rear air duct valve.

Easy to handle. Environmentfriendly. Cleaning brush included.

6316

„Mini“ Blower

Bellows

Compact rubber bulb. Fine, short front air nozzle, rear air duct valve. Easy to handle.

6305

6314

Blower Brush

Flat brush with large rubber blower bulb.

6328

Micro Fibre Cleaning Cloth

Fluff-free, grease-absor bing. Hemmed edges.

6662

Display and Optics Cleaning Kit

Pump spray and a micro fibre cleaning cloth.

6699

Cleaning Set

Lens cleaning paper, cleaning leather and blower brush

6663

Cleaning Set

Cleaning pen and micro fibre cloth.

6697

Cleaning Set

Optical-glass cleaning fluid, cleaning paper and blower brush.

9084_DigitalZub_GB_1012_DigitalZub_9084_GB_0812 23.10.12 11:32 Seite 16

8818

Portable Protection

„EasyLoader“

Camera Bag

With accessory pockets inside the outer lid and on both sides. Internal lid can be connected via a Velcro closure. Spacious front pocket with organizer pouches and zipper. This camera bag allows quick access, as the top opens away from the body and stays open in a fixed position. With carrying handle and detachable, adjustable and padded shoulder strap. Inside dimensions: 15.5 x 15 x 10 cm (6.1 x 5.9 x 3.9

in.)

„SmartLoader“

Camera Bag

Lid opens away from the body and stays open in a fixed position thus providing quick access to the camera. Three mesh pockets. Zipped front pocket with overlapping cover and inside card pocket.

Main compartment with divider.

Padded handle. Adjustable carrying strap and shoulder pad. Belt loops.

8825

SmartLoader S, for megazoom cameras and camcorders.

Inside dimensions (WxHxD):

10 x 13 x 8 cm (3.9 x 5.1 x 3.1 in.).

8826

SmartLoader M, for bridge cameras, mirror-less interchangeable-lens cameras and camcorders. Inside dimensions (WxHxD):

16 x 10 x 9 cm (6.3 x 3.9 x 3.5 in.).

8827

SmartLoader L, for DSLR cameras. With lens support divider.

Inside dimensions (WxHxD): 17.5 x 13 x 10 cm (6.9 x 5.1 x 3.9 in.).

8827

Battery Box

For 4 AA or

AAA batteries.

2 pieces. Stackable.

Color: grey and blue.

Memory Card Box

Slim plastic box for secure storage of two SD or CompactFlash memory cards.

Shaped rubber insert. Protects against shock, dirt and moisture. With secure latch.

6495: grey

6496: neon yellow

„digiShell“ Hard Shell

Camera Bags

Compact camera bags with hard shell exterior and two-way zipper. Interior accessory pocket.

With belt loop, detachable carrying strap and snap hook.

digiShell 1,

9.5 x 6 x 2.5 cm*

(3.7 x 2.4 x 1 in.)

8281 black

8282 blue

8283 grey

*inside dimensions (WxHxD) digiShell 2,

10.5 x 6.5 x 3.3 cm*

(4.1 x 2.6 x 1.3 in.)

8287 black

8288 blue

8289 grey

6497

6494

Memory Card Box

Flat metal box for three SD/

Multimedia / xD / Memory

Stick cards. Dimensions: approx. 9.5 x 6 x 0.5 cm

(3.7 x 2.4 x 0.2 in.)

9084_DigitalZub_GB_1012_DigitalZub_9084_GB_0812 23.10.12 11:33 Seite 17

Handy Stuff

Photo Functional Gloves

Half finger gloves with mitten cover and thumb cover provide for perfect mobility, secure grip and ideal protection against cold. Mitten and thumb cover can be folded back and fastened with a Velcro strip.

Made of breathable, skin-friendly fleece with anti-slip coating.

6370: Size M

6372: Size L

6374: Size XL

6376: Size XXL NEW

6701: „Profi“ professional camera hand strap

6702: „Profi 2.0“ professional camera hand strap with additional safeguard belt around the wrist for more safety and stability.

NEW

6702

Professional Camera Hand Strap

Suitable for larger compacts,

(D)SLRs and system cameras. Soft padded genuine leather hand support with adjustable fixtures.

Camera mounting plate with tripod thread and foldable legs providing a secure stand when put on table or floor.

6701

6791

6778

6779

6737 black

6752 black

6738 red

6753 red

6739 olive-green

6754 olive-green

6740 brown

6755 brown

6735/6745

6736/6746

6747 silver/black 6748 silver/red

6742

6780

Carrying Straps and Wrist Straps

For com pacts with one fastening eye. Also suitable for mobile phones, MP3 players etc.

6737-40 Wrist Strap, genuine leather, Length: approx. 22 cm (8.7 in.)

6752-55 Carrying Strap, genuine leather,

Length: approx. 46 cm (18.1 in.)

6735

6745

Silver chain with clear plastic cover

Wrist Strap, Length: approx. 24 cm (9.4 in.)

Neck Chain, Length: approx. 46 cm (18.1 in.)

6736

Soft elastic textile fabric

Wrist Strap, Length: approx. 26 cm (10.2 in.)

6746 Carrying Strap, Length: approx. 49 cm (19.3 in.)

6747/48 Reflective Carrying Strap, with quick release lock,

Length: approx. 47 cm (18.5 in.)

6742 Neoprene Camera Strap. High carrying comfort, quick release lock for camera, Length: approx. 53 cm (20.9 in.)

Camera Shoulder Straps

For cameras with two fastening eyes. Length adjustable.

6780 Neoprene strap. Detachable end sections, can be reconnected to serve as a wrist strap. Length: max. 140 cm

(55.1 in.).

6791 Professional camera strap. Heavy-duty strap with nonslip protection. Length: approx. 110 cm (43.3 in.).

6778/79 „Adventure“ camera strap. Heavy-duty strap with nonslip protection. Detachable end sections can be reconnected to serve as a wrist strap. Length: max. 145 cm

(57.1 in.)

6778: Denim

6779: Khaki

NEW

9084_DigitalZub_GB_1012_DigitalZub_9084_GB_0812 23.10.12 11:33 Seite 18

Light – Compactly Sized

V ideo needs light – permanently – that is continuous light. Nowadays digital cameras can shoot videos. Small add-on lights, portable and battery-powered, provide adequate illumination in a close-up range when lighting conditions are bad.

StarCluster and Co. use up-to-date LED technology, provide energy-saving operation with long-life light sources and can be mounted on all camcorders and movie-making digital camera with standard accessory shoe.

Kaiser StarCluster

This compact soft light works for both, stills and video filming and is perfect for use with D-SLRs and CSCs.

It features 96 continuously dimmable white LEDs on a panel of 8.5 x 6 cm (3.3 x 2.4 in.) and provides approx. 600 lux of illumination at one meter (3 feet) and 60° angle of radiation (half-value angle). The colour temperature of 5600 Kelvin relates to daylight.

It is powered by five AA batteries fitted in the rear battery compartment or by a Canon LP-E6 battery, that can be placed in an adapter on the battery cover. The

LP-E6 is the standard battery for Canon’s 5D Mk II, 7D and 60D. There is also a connector for a mains adaptor (optional). The light comes with an diffusion screen and an artificial light filter (3200 Kelvin) which attach to the front of the light by magnetic attachments. The package also contains a swivel joint for mounting to a standard hot shoe.

Specifications:

Operating time with fully charged batteries: up to 2.5 hours

Colour temperature: 5600 Kelvin

Operating voltage: 5.8 - 16.8 V

Dimensions: 127 x 77 x 45 mm (5 x 3 x 1.8 in.)

Weight: 195 g / 6.9 oz. (without batteries)

Tripod thread: A 1/4

Accessories: 3271 mains adapter

3270

Several lights can be combined side by side or on top of each other using a clever catching system.

9084_DigitalZub_GB_1012_DigitalZub_9084_GB_0812 23.10.12 11:33 Seite 19

More Light: Video Lights with Three-chip-LEDs

3 Chip LEDs are LEDs that only require the space of a single “common” LED. This allows for a particularly compact design, but makes high demands on an effective heat dissipation. Technical characteristics of the L2S-5K and L10S-5K lights are similar with respect to lighting, otherwise they have differing concepts.

The similarities

• 7.5 x 5 cm (3 x 2 in.) panel with 96 three-chip LEDs.

• Color temperature: 5400 Kelvin.

• Continuously dimmable.

• Extremely wide angle of radiation: 110 degrees (half-value angle).

• Electronically stabilized light output keeping the illuminance constant when supply voltage goes down.

• Automatic shutdown when batteries are exhausted to prevent deep discharge and battery defects.

• Rear LCD displays dimmer position.

• Battery compartment for standard Sony L-type battery.

• Connection for external power source.

• Illuminance: 380 lux at 3 ft. (1 m) and 110 degrees angle of radiation.

• 1/4" tripod thread.

• Honey comb filter for more directional light, 7.2 V / 2200 mAh lithium-ion-battery, charger, swivel/tilt joint for mounting the light to the accessory shoe and Sony/Minolta hot shoe adapter are supplied with the light.

• Mains adapter (3263) is an optional accessory.

3260

3255

3248

The differences

L2S-5K LED Video Light

• Built-in blower cooling.

• Blower speed controlled automatically and temperature-dependent.

• Blower speed can be controlled manually in five levels.

• Rear LCD displays blower speed level.

• Modular design: LED panel can be removed and exchanged for a 3200 Kelvin panel (3261, optional accessory).

• Operating time: up to 45 minutes

(depends on battery condition).

• Weight without battery: approx. 200 g

(0.4 lbs).

• Dimensions of light head: 93 x 75 x

43 mm (3.7 x 3 x 1.7 in.)

• Code no. 3260

L10S-5K LED Video Light

• Convective cooling via large built-in heat sink.

• Integrated LED panel.

• Operating time: up to 50 minutes

(depends on battery condition).

• Weight without battery: approx. 190 g (0.4 lbs).

• Dimensions of light head: 93 x 83 x 25 mm

(3.7 x 3.3 x 1 in.)

• Code no. 3255

3261

9084_DigitalZub_GB_1012_DigitalZub_9084_GB_0812 23.10.12 11:34 Seite 20

Even More Light . . .

R 48 Ring Light

providing shadowless illumination for macro work and close-up shots. Colour temperature is at 6000

Kelvin. Mounting on the lens is easy as the unit slides and locks on the suitable adapter ring. Six adapter rings from 49 to 67 mm are included. The light is powered by two AA rechargeable batteries (not included) housed in a separate battery compartment or by a mains adapter 3271 (optional accessory). The 24

LEDs on the left or on the right can be switched on separately.

Specifications:

Minimum working distance: 3 cm (1.2 in.)

Operating time with 2 NiMH rechargeables: approx. 2.5 hours

Colour temperature: 6000 K +/- 500 K

Dimensions: Ring light: 11 x 13 x 3 cm

(4.3 x 5.1 x 1.2 in.)

Battery compartment: 5 x 9 x 5 cm

(2 x 3.5 x 2 in.)

Weight: Ring light: approx. 140 g (4.9 oz.)

Battery compartment: approx. 55 g

(1.9 oz.)

3248

KR 90 Ring Light

Professional ring light with 30 three-chip high performance LEDs. The light intensity corresponds to that of a

30 watt fluorescent light. extremely wide angle of radiation on 110°. A rechargeable lithium-ion battery and the complete circuitry are integrated in the main body made of highly durable duralumin. The light can be dimmed down to 50 %. The basic connection thread is 77 mm, several adapter rings from 55 to 72 mm are included. Light can also be mounted on a tripod. No light loss due to battery consumption. A quick charger is included. Tripod thread: 1/4"

Specifications:

Min. working distance: 3 cm (1.2 in.)

Operating time (continuous lighting and fully charged battery): 2 hours

Battery capacity: 1500 mAh

Colour temperature: 5500 K +/- 500 K

Dimensions: ø 142 x 34 mm (ø 5.6 x 1.3 in.)

Weight: 300 g /10.6 oz.

3250

9084_DigitalZub_GB_1012_DigitalZub_9084_GB_0812 23.10.12 11:34 Seite 21

. . . and Useful Things

Camlight Nova

Hand Grip

Compact camcorder light with 20 watt halogen lamp. Specially designed reflector for even illumination. 3200 K colour temperature. Slide-in foot for upright or horizontal mounting, with blocking screw and 1/4“ tripod thread. Powered by NiMH rechargeables (5 x AA, not in cluded). Operating time up to 40 minutes. Battery compartment inside light housing. On/Off switch. Incl. 1108 Uni ver sal Accessory Bracket.

Dimensions: (WxHxD): 55 x 98 x 72 mm (2.2 x 3.9 x 2.8 in.)

Weight: 110 g (without batteries)

For lighting units, cameras, etc.

With foam shell and grip shape. Connection thread 1/4" and tripod thread 1/4".

Includes snap-hook with key-ring and fixture for tripod thread.

Height: approx. 120 mm (4.7 in.)

3272

3288

Accessory

Bracket

Universal Accessory Bracket

For camcorders and digital

SLRs/CVCs and compacts.

Allows for right side or left side mounting of accessories such as lights or microphones. The bracket can be aligned to the camera in different ways.

Angle piece with accessory shoe

3273

Light metal bracket for mounting two accessories with tripod thread on a tripod, hand grip or swivel joint. Especially suitable for attaching two „StarCluster“ LED lights.

Two relocatable 1/4" tripod screws with soft washers. Center placed 1/4" tripod bush.

Length: approx.

15.5 cm (6.1")

Width: approx.

2.5 cm (1.0")

Plug-in bracket with detachable anti-twist protection and tripod adapter screw

1108

Mounting Foot

Accessory

Bracket

For raised mounting of a light, microphone etc. next to the camcorder lens. Folding. With antitwist pin for exact right-angled mounting on camcorder. Widened three-point rest on bottom side. Camera with mounted bracket stands firmly on all flat surfaces.

1/4“ tripod thread.

6040

With accessory shoe for lighting units, flashguns etc. Tripod thread 1/4" for attachment on tripods. Dimensions: 94 x 63 x 11 mm

(3.7 x 2.5 x 0.4 in.)

93296

9084_DigitalZub_GB_1012_DigitalZub_9084_GB_0812 23.10.12 11:34 Seite 22

Enough Light

T he lights of the „studiolight“ line are absolutely suitable for the small home studio. They are compact, sturdy and can be combined with various light modelling accessories. They are easy to use, and the lighting situation is the same for set-up and shooting.

3157

„studiolight H“ Lighting Unit

1000 watt studio light with dimmer and built-in blower cooling. Front section with bayonet attachment for accessories. Swivel joint and umbrella mount. Supplied with 1000 watt halogen lamp, safety glass bulb dome, lamp protector and 180 mm (7 in.) metal reflector. Code no. 3152

„studiolight H Kit“ Lighting Kit

Comprised of 2 „studiolight H“ lighting units (3152), 2 heat-resistant soft box es 60 x 60 cm (23.5 x 23.5 in.) and 2 air cushioned light stands, 70-

230 cm (27.5 - 90.5 in.). In carrying bag 94 x 30 x 27 cm (37 x 11.8 x

10.6 in.). Code no. 3155

„studiolight H Trio“ Lighting Kit

Comprised of 3 „studiolight H“ lighting units (3152), 2 heat-resistant soft boxes 60 x 60 cm (23.5 x 23.5 in.) and 3 air cushioned light stands (setting height 70-230 cm / 27.5-90.5 in.). Set comes in a rugged trolley with plastic wheels and bumpers, telescopic handle, two carrying handles and adjustable carrying strap with shoulder pod for easy carrying and safe storage. Customisable interior with removable dividers. Outside dimensions:

88 x 46 x 35 cm (34.6 x 18.1 x 13.8 in.). Code no. 3157

3154

„studiolight C“ Lighting Unit

With screw-in fixture E 27 for photofloods up to 500 watts. Built-in blower cooling. Front section with bajonet attachment for accessories, swivel joint and umbrella mount. Includes 150 W lamp, lamp protector, and 180 mm (7 in.) metal reflector. Code no. 3150

„studiolight C Kit“ Lighting Kit

Comprised of 2 „studiolight C“ lighting units (3150), 1 reflector umbrella, silver, 100 cm (39.5 in.), 1 transmitted light um brella, 100 cm (39.5 in.),

2 air cushioned light stands, 70 - 230 cm (27.5 - 90.5 in.). In carrying bag

94 x 30 x 27 cm (37 x 11.8 x 10.6 in.). Code no. 3154

Additional accessories for „studiolight H”, „studiolight C” and „studiolight 1010”

3177-78

Soft Boxes

Heat-resistant, with ventilation flaps. 60 x 60 cm / 23.5 x

23.5 in. (3177) and 100 x 100 cm / 39.5 x 39.5 in. (3178).

3160

3159

Reflectors

3159: narrow beam, 3160: wide beam, with deflector.

3170

Background Reflector

Rotatable, position lockable.

„studiolight C Trio“ Lighting Kit

Comprised of 3 „studiolight C“ lighting units

(3150), 1 reflector umbrella, silver (100 cm / 39.5

in. diameter), 1 studio umbrella, white (100 cm diameter) and 3 air cushioned light stands (setting height 70-230 cm / 27.5-90.5 in.). Set comes in a rugged trolley with plastic wheels and bumpers, telescopic handle, two carrying handles and ad justable carrying strap with shoulder pod for easy carrying and safe storage. Cus tomisable interior with removable dividers. Outside dimensions: 88 x

46 x 35 cm (34.6 x 18.1 x 13.8 in.). Code no. 3156

9084_DigitalZub_GB_1012_DigitalZub_9084_GB_0812 23.10.12 11:34 Seite 23

„studiolight 1010” Halogen Studio Lighting Unit

With 1000 Watt halogen lamp and protective lamp cover made of safety glass. Brightness can be adjusted via step-up/step-down buttons, two-digit display. Light can be switched from set brightness to full brightness and back. Low-noise blower cooling for unlimited operation in every position. Bayonet attachment with quick locking device for accessories (reflectors, soft boxes), swivel joint with locking lever, umbrella mount. Mounts on suitable tripods/stands with 16 mm standard spigot.

Includes halogen lamp, exchangeable reflector (180 mm / 7 in. diameter) and protective lamp cover.

Code no. 3164

3164

3165

„studiolight 1010 Kit” Lighting Kit

Comprised of 2 „studiolight 1010“ halogen lighting units (3164),

2 heat resistant soft boxes 60 x 90 cm (23.6 x 35.4 in.) and 2 aircushioned light stands (setting height 65-225 cm / 25.5-88.5 in.) in a sturdy carrying case. Outside dimensions: 73 x 28 x 44 cm

(28.7 x 11 x 17.3 in.). Code no. 3165

300 W Portable Lighting Kit

Complete light-stand-umbrella combination.

Comprises „videolight 8 S“ 300 W safety light ing unit (93307), light stand (5031), joint with umbrella mount (5041), and white studio umbrella (3080). In carrying bag with handle and adjustable shoulder strap.

1000 W Portable Lighting Kit

Complete light-stand-umbrella combination.

Comprises „videolight 6“ 1000 W safety light ing unit (93304), light stand (5031), joint with umbrella mount (5041) and white studio umbrella (3080). In carrying bag with handle and adjustable shoulder strap.

Light Stands

Sturdy matt black light stands with 1/4" / 3/8” reversible thread pin, that can be attached either vertically or horizontally. The center column is air cushioned and thus provides secure use.

3195: „Small“ Light Stand.

Four section center column. Setting height: approx. 75 - 230 cm (29.5 – 90.6 in.)

Length closed: approx. 70 cm (27.6 in.)

Max. load: 3 kg (6.6 lbs.)

Weight: approx. 1650 g (3.6 lbs.)

3196: „Large“ Light Stand.

Three section center column

Setting height: approx. 110 -

290 cm (43.3 - 114.2 in.)

Length closed: approx.

105 cm (41.3 in.)

Max. load: 10 kg (22 lbs.)

Weight: approx.

2200 g (4.9 lbs.)

3195

3196

3047 3049

9084_DigitalZub_GB_1012_DigitalZub_9084_GB_0812 23.10.12 11:34 Seite 24

Desktop Studios

5911

D esktop studios can be set up on your desk, on your dining or living room table or wherever you like to take your pictures. They are most suitable for small object photography resulting in pictures you may need for your website, for internet auctions, for online shops or for documentation of valuables or collectables.

Studio-out-of-the-Box

Compact foldable studio for digital photography. Comprises table, background support, background material and trapeze stand for cameras up to

500 g (1.1 lbs.). On the trapeze stand the camera can be positioned in many different positions and at different heights and distances from the object. The camera platform is pivotable and relocatable and can be locked in a vertical shooting position. Table can be extended up to 30 cm (11.8 in.), background can be positioned at different heights. Background roll included, approx. 40 cm (15.7 in.) wide and 130 cm (4.25 ft.) long. To support wider backgrounds a clip-on rail is included. Dimensions (folded): 59 x 6 x 33 cm (23.2 x 2.4 x

13 in.). Supplied with carrying box: 60,5 x 10 x 48,5 (23.8 x 3.9 x 19.1 in.).

A suitable Lighting Set (2 x 8 W, 4000 K) is available as an accessory (5914).

5876

5875

5883

"Open Tube 1" Shooting Table

The evenly curved background ("open tube" outline) improves the distribution of light on the subject.

5884

This shooting table is assembled by the user. The background made of flexible plastic material is inserted into the assembled table and fixed by

Velcro fittings. Dimensions 77 x 60 x 85 cm (30.3 x 23.6 x 33.5 in.). Side frames of the table provide attachment points for one or more lighting modules in vertical or horizontal position.

Suitable lighting module, high frequency operated: 5884 (36 W, 5400 K).

"ConCave" Background

Flexible plastic plate, can be bent into the desired shape and then be fixed by means of two ”beads” and choice of respective holes. Dimensions of flat plate: approx. 60 x 30 cm (23.6 x 11.8 in.).

5875: opaque plate for shooting with reflected light

5876: transparent plate, for shooting with reflected light and backlight

9084_DigitalZub_GB_1012_DigitalZub_9084_GB_0812 23.10.12 11:35 Seite 25

5891 5863

„Dome-Studio“ Light Tent

White translucent surfaces provide even and soft illumination.

Umbrella-type construction makes set-up and fold-down easy.

Equipped with „snow flaps“ for outdoor use to prevent it from blow ing away in strong winds.

Supplied with reversible textile background (blue / grey) and protective cover with carrying straps.

5891: Floor size: 62x62 cm (24.5x24.5 in.), height: 51 cm (20 in.)

5892: Floor size: 75x75 cm (29.5x29.5 in.), height: 65 cm (25.5 in.)

Table-Top-Studio digital

5994/96

Complete desktop studio, consisting of Small Product Table 5931 and lighting Unit. Product table with white translucent concave shaped acrylic background. Required desk space approx. 50 x 50 cm (20 x 20 in.). Lighting unit consists of two small soft lights for even and smooth illumination and holding rods with multiple orientation possibilities, screw-on clamps for attachment.

Table-Top-Studio digital SN-HF (5993) with RB 218N HF daylight lighting system (5464) with two compact fluorescents, 18 W each, 5400 K, CRI = 90 - 100. Table-Top-Studio digital SN-HF plus (5994) with additional camera clamp holder comprising a swan-neck arm, a ball head and a desk clamp.

Also available with RB 5020 DS LED daylight lighting system

(5465) with 192 white high-CRI LEDs on each side: Table-

Top-Studio digital LED (5995) and Table-Top-Studio digital

LED plus (5996). Lights can be dimmed individually or synchronized, 5600 K, CRI > 85, angle of radiation: 60°.

„Cube-Studio“ Light Tent

This cube-shaped light tent allows for even and soft illumination. Detachable front cover with slot for camera lens. Easy to set up, folds up automatically. Highly flexible frame, can be folded down to compact size. Includes reversible textile backdrops white/grey and black/blue and carrying pouch with wrist strap.

5893: 50 x 50 x 50 cm (19.5 x 19.5 x 19.5 in.)

5894: 90 x 90 x 90 cm (35.5 x 35.5 x 35.5 in.)

Desktop Lighting

5861: Desktop Lighting Kit 1: reflector light, consisting of lamp holder 5860, reflector (27 cm / 10.6 in. diameter) with removable diffusing cover and light stand

5859. Without lamp.

5862: Desktop Lighting Kit 2, comprises two sets 5861

5860: Lamp Holder with E 27 ceramic socket, for photofloods up to 250 watts. With ON/OFF switch and swivel joint with umbrella mount. Mounts on suitable tripods/stands with 16 mm standard spigot. Mains lead approx. 3,80 m (12.5 ft). 1 piece. Without lamp and reflector.

5858: Desktop Light Stand, height 22-38 cm (8.7-15 in.)

5859: Desktop Light Stand, height 35-70 cm (13.8-27.6 in.)

3110: Energy Saving Lamp, 25 W, 6400 K, E27

5860

Desktop Shooting Kit

Comprehensive Kit for object photography. Consists of a „Cube-Studio“ light tent for even and soft light distribution and two reflector lights on desktop stands

(Desktop Lighting Kit 2, code no. 5862).

5863: with Cube-Studio 50 x 50 x 50 cm (19.5 x 19.5 x 19.5 in.) (5893)

5864: with Cube-Studio 90 x 90 x 90 cm (35.5 x 35.5 x 35.5 in.) (5894)

Mini Magic Arm

To mount and individually align cameras, lights and accessories. 1/4” mounting thread. Central locking knob.

Comes with multiple mounting adapters. Max imum load in horizontal position: 1 kg (2.2 lbs.)

5055: Mini Magic Arm 1, total length approx. 18 cm (7.1 in.)

5056: Mini Magic Arm 2, total length approx. 29 cm (11.4 in.)

Universal Clamp

Attaches on tubes and boards. Span width max. 42 mm (1.7 in.). Two threaded holes 1/4” and 3/8”. Includes spigot with 1/4” and 3/8” threaded pins.

5023

More accessories available: Holding

Frame (5934) and

„prolite basic 2“

Soft Light Source

(2425)

9084_DigitalZub_GB_1012_DigitalZub_9084_GB_0812 23.10.12 11:35 Seite 26

For Everything that

Won’t Fit Your Scanner!

J ust in case something would not fit on your scanner – too big, too bulky, too wide etc. – here is where it belongs. Combine these stands with your camera and enjoy a perfect image capturing tool for all

“awkward” items that need to be photographed from above: the vintage LP cover, grandfather’s precious pocket watch or just a section out of a large-sized road map.

Suitable lights – now also available with LEDs – for even illumination, can easily be added.

RS 2 XA Camera Stand

Non-reflective matt grey baseboard with printed fine grid and cm/inch scale. Matt-black anodised aluminium-section tube column with cm/inch scale. Hand-cranked height adjustment. Horizontally adjustable camera arm. 1/4” mounting thread. Baseboard (WxHxD): approx.

40 x 2.5 x 50 cm (15.7 x 1 x 19.7 in.). Column height: approx. 76 cm

(30 in.). Maximum load: 1.5 kg (3.3 lbs.). Code no. 5411

RB 5020 DS LED Lighting Unit

With two small light banks, each with 192 white high-CRI LEDs,

5600 K, angle of radiation: 60°.

Lights can be dimmed individually or synchronized. Lights are tiltable and adjustable in height. Angle of vertical arms adjustable by lock joint. Mounted with strong diecast clamp bases. Code no. 5465

RB 218N HF Lighting Unit

With two small light banks with in terior reflector and 18 W, 5400 K daylight fluorescent lamp. High fre quency operating system. Lights are tiltable and adjustable in height.

Angle of vertical arms adjustable by lock joint. Mounted with strong diecast clamp bases. Code no. 5464

RB 2 Lighting Unit

With four tiltable and adjustable reflectors on mounting arms which are in turn tiltable and adjustable in height. Lights can be switched on separately. Suitable lamps:

4 x 150 W max. Supplied without lamps. Code no. 5450

„reprokid“ Camera Stand

Super-compact camera stand for small, lightweight cameras.

Non-reflective, matt-black baseboard. Column with cm/inch scale. Height-adjustable camera arm. 1/4” mounting thread. Baseboard

(WxHxD): 32 x 1.9 x 38 cm (12.6 x 0.7 x 15 in.). Column height:

59 cm (23.2 in.). Max. load: 1 kg (2.2 lbs.). Includes lighting unit with two E 27 screw-in mounts for lamps up to 250 Watt (supplied without lamps). Code no. 5360

5411 with 5464

9084_DigitalZub_GB_1012_DigitalZub_9084_GB_0812 23.10.12 11:35 Seite 27

Pixel-Perfect Cut?

T his is not required. But it would be nice to have all the things “produced” on your printer with a neat and precise cut. This makes a trimmer a PC peripheral – it is very useful anyway.

"easy cut" Safety Trimmer

4306-07

Easy and safe cutting with ground circular blade. Automatic paper clamping at cutting position. Sturdy metal base board with scales, format and angle markings.

4306: easy cut 1 cutting length: 32 cm (12.6 in.) cutting thickness: 1.0 mm (0.04 in.)

4307: easy cut 2 cutting length: 45 cm (17.7 in.) cutting thickness: 0.8 mm (0.03 in.)

„hobby cut“ Safety Trimmer

4314

4313

Self-sharpening circular blade in closed plastic housing. Automatic paper clamping at cutting position. Transparent paper-holding strip. Two angle stops with cm and inch scales. Sturdy metal base board with printed fine grid, scales, format and angle markings.

4313: hobby cut 3

Cutting length: 33 cm (13.0 in.),

Cutting thickness: 1 mm (0.04 in.)

4314: hobby cut 4

Cutting length: 46 cm (18.1 in.),

Cutting thickness: 1 mm (0.04 in.)

Hand-Held

Magnifier

Stylish magnifier with

LED illumination.

Ergonomically designed handle.

Lens edge mattfinished and rounded off.

Batteries included.

2368: Lens diameter: 65 mm (2.6 in.), magnification: 3x

2369: Lens diameter: 80 mm (3.2 in.), magnification: 2.2x

Pocket

Magnifier

Flat magnifier with LED light. The LED lights up when loupe slides out.

Magnification: 2.4x

Lens size: 52/34 mm (2/1.3 in.)

2371

9084_DigitalZub_GB_1012_DigitalZub_9084_GB_0812 23.10.12 11:35 Seite 28

Worth Watching!

T oday's digital cameras and flashguns offer an almost endless number of features and settings. Manuals covering every detail require several hundred pages.

To get the most out of your digital SLR or flashgun quickly and easily you should try these video tutorials from Blue Crane Digital. All you need now is a

DVD player and about two hours of your time. Then you will learn how to create the images you want.

You can closely follow settings and procedures, basic knowledge will be explained and sample images will show the results. All topics are arranged in chapters, so you can move at your own pace and return later to individual subjects.

These German language DVDs are produced specifically for the European market and are distributed exclusively by Kaiser Foto technik.

Available titles:

6432: Nikon D800 NEW

6434: Canon 5D Mark III, Grundlagen

NEW

6439: Nikon D90, Erweiterte Funktionen

6440: Canon 50D

6445: Canon 500D

6447: Canon 7D, Grundlagen

6449: Perfekte Videos mit Canon-DSLR-Kameras

6450: Canon 60D, Grundlagen

6451: Nikon D7000

6452: Nikon D3100

6453: Canon 600D

6454: Canon 1100D

6455: Nikon D5100

6456: Nikon Speedlight SB-910

6457: Nikon Speedlight SB-700

NEW

6458: Nikon Speedlight SB-900/800/600

6459: Canon Speedlite 580 EX II / 430 EX II

Please note: Tutorials are

German language only.

USA

HP Marketing Corp.

P.O., Box 715

Pine Brook, NJ 07058

Tel (+1) 973-8089010

Fax (+1) 973-8089004 www.hpmarketingcorp.com [email protected]

United Kingdom

Fotospeed Distribution

Jay House Ltd.

6B Park Lane Industrial Estate

Park Lane, Corsham

SN13 9LG

Tel (+44) 1249-714555

Fax (+44) 1249-714999 www.fotospeed.com

[email protected]

Canada

Nadel Enterprises Inc.

425 Attwell Drive

Rexdale, Ontario

M9W 5C4

Tel (+1) 416-7452622

Fax (+1) 416-7422616 www.nadel.ca

[email protected]

New Zealand

Photo Warehouse Ltd.

175 GT North Rd.

Ponsonby-Auckland

Tel (+64) 9-3032148

Fax (+64) 9-3099721 www.photowarehouse.co.nz

[email protected]

Kaiser Fototechnik GmbH & Co. KG

Im Krötenteich 2 · 74722 Buchen · Germany

Tel.: +49(0)6281 407- 0

Fax: +49(0)6281 40755 www.kaiser-fototechnik.de

[email protected]

Γεια σας! Είμαι ένα AI chatbot ειδικά εκπαιδευμένο για να σας βοηθήσει με το Kaiser Fototechnik MonoCR-C2 Datasheet. Έχω εξετάσει διεξοδικά το έγγραφο και μπορώ να σας βοηθήσω να εντοπίσετε τις ακριβείς πληροφορίες που χρειάζεστε ή να εξηγήσω το περιεχόμενο με σαφείς και απλούς όρους. Είτε ψάχνετε για καθοδήγηση σχετικά με συγκεκριμένες λειτουργίες, βήματα αντιμετώπισης προβλημάτων ή γενική χρήση, μη διστάσετε να κάνετε τις ερωτήσεις σας. Όσο περισσότερες λεπτομέρειες παρέχετε σχετικά με τις ανησυχίες ή τις ανάγκες σας, τόσο πιο ακριβή και αποτελεσματικά μπορώ να σας βοηθήσω!

Πληκτρολογεί ο βοηθός

Ο βοηθός δεν είναι διαθέσιμος. Παρακαλώ, προσπαθήστε ξανά αργότερα.

Διαφήμιση