- Industrial & lab equipment
- Electrical equipment & supplies
- Batteries & accessories
- Battery chargers
- Skyrc
- E8
- Instruction manual
Skyrc | E8 | instruction manual
Add to my manuals
2 Pages
Skyrc E8 is an economic, high quality 100-240V AC balance charger, designed for charging LiPo and LiFe batteries from 2-8 cells in balance mode. With a circuit power of 100W and a max charge current of 6A, you can select the proper charge current according to battery capacity. It features four different charge current options: 1A, 3A, 5A, and 6A. The charger comes with a built-in power supply and can charge batteries in CV and CC modes, indicated by different LED colors.
advertisement
▼
Scroll to page 2
INSTRUCTION MANUAL SK-100096 INTRODUCTION Thank you for your choice of the SKYRC e8, 100-240V AC balance charger. This unit is simple to use but its operation does require some knowledge on the part of the user. Please read this entire operating manual completely and attentively before using this product, as it covers a wide range of information on operating and safety. SKYRC e8 Charger is an economic, high quality 100-240V AC balance charger, designed for charging LiPo and LiFe batteries from 2-8 cells in balance mode. The circuit power is 100W and max charge current can reach to 6A. There are four different charge current 1A/3A/5A/6A which can be selected. You could select the proper charge current according to battery capacity. when the charge status LED glows constant orange, the charger is charging in CV mode; 8) When the cell LED is flashing, this cell is discharging for balancing. 9) When the battery is fully charged, the charge status LED will glow constant green. 10) Unplug the battery from the charger and the charge status LED will flash green which indicates the charger is ready to charge another battery. Charger Balance Adaptor LiPo Battery CAUTION: This diagram shows the correct way to connect your battery to the e8 charger while charging in balance mode. Failure to connect as shown in this diagram will damage this charger. The main battery leads must be connected along with the balance lead connector as shown before charging your battery. CONNECTION DIAGRAM AC 100-240V PowerJack Cell 4 LED Indicator Cell 3 LED Indicator Cell 2 LED Indicator Cell 1 LED Indicator EXPLANATION OF LED STATUS Cell 5 LED Indicator Cell 6 LED Indicator Cell 7 LED Indicator Battery Type Switch Charge Status LED Cell 8 LED Indicator Cell Status LED Charge Current Switch BatterySocket Charge Status LED Indicator XH BalanceSocket LED green blinking The charger is ready to charge. LED glows constant red The charger is charging in CC mode. LED glows constant orange The charger is charging in CV mode. LED glows constant green. The charging process finishes. LED glows constant red. The cell is charging. LED flashes red The cell is discharging. * Error Message If there is an error, the charge status LED and one of the cell LED will blink in sequence. LED Status Error Message charge status LED + Cell 1 LED The voltage difference among cells is too big (more than 300mV) charge status LED + Cell 2 LED Wrong connection Over current protection Reverse polarity charge status LED + Cell 3 LED CHARGE PROCEDURES charge status LED + Cell 3 LED SKYRC e8 comes with the built in power supply. You can connect the AC power cord to the AC socket (100-240V AC) directly. Note: This charger can charge LiPo and LiFe batteries ONLY in balance mode. In this case, you must use balance board to connect the charger with the battery. Please refer to following steps to charge the battery, 1) Insert the AC power cord into the charger. 2) Insert the AC cord into a wall socket (100-240V). All LEDS will light for 1 second and the charge status LED will flash green which indicates the charger is ready to charge. 3) Select the battery type LiPo/LiFe by the slide switch. 4) Select the proper charging current 1A/3A/5A/6A by the slide switch. 5) Connect the battery to the charger main battery lead to battery socket and balance wires to balance socket. 6) The charger starts charging. The charge status LED and the cell status LED will glow constant red. If the battery pack is 2-cell, Cell 1 and Cell 2 LEDs will glow constant red; if the battery pack is 3-cell, Cell 1, Cell 2 and Cell 3 LEDs will glow constant red; and so on. 7) During the charging progress, when the charge status LED glows constant red, the charger is charging in CC mode; -1- In this case, please disconnect the power cord from the wall socket and unplug the battery from the charger. SPECIFICATION AC Input 100-240VCharger/Cell Status Battery Type LiPo/LiFe Cell Count 2-8 cells Charge Current 1A/3A/5A/6A ± 10% Cell Terminate Voltage LiPo: 4.2V ± 0.02V / LiFe: 3.6V ± 0.02V Circuit Power 100W Current Drain for Balancing 200mA Dimension 150x93x51mm Weight 450g -2- THE SET CONTAINS WARNINGANDSAFETY NOTES SKYRC e8 is suitable for charging rechargeable LiPo/LiFe batteries. Do not attempt to recharge dry cells. Charging other types of batteries may cause fire or explosion. Never leave the charger unattended when it is connected to its power supply. The allowable AC input voltage is 100-240V AC. Never connect it to any other voltage. Protect charger from dust, dirt and damp. Never place the charger and batteries connected to it on any form of flammable surface. Never operate the charger in the vicinity of inflammable material or gas. Ensure that there is an unrestricted airflow to and from the charger's cooling slots. Never place the charger on a carpet or similar surface. Take great care to maintain correct battery polarity, and avoid shot-circuit. Read the battery manufacturer's instructions and adhere to them strictly. SkyRC e8 Charger AC Power Cord 18AWG Wire Charging Cable Balance Adaptor RECOMMENDED ACCESSORIES EH Adaptor XH Adaptor SK-600014-01 SK-600020-04 TP/FP Adaptor SK-600018-02 HP/PQ Adaptor Tamiya charging cable SK-600016-03 5201-0030-01 CONFORMITY DECLARATION SKYRC e8 satisfies all relevant and mandatory CE directives and FCC Part 15 Subpart B: 2014. The product has been tested to meet the following technical standards: Test Standards CE-LVD Futaba RX charging cable EC3 charging cable 5201-0044-01 5201-0034-01 Crocodile clip charging cable Dean charging cable 5203-0012-01 EN60335-2-29 Conform EN61000-3-3 Electromagnetic compatibility (EMC) - Part 3-3: Limits Limitation of voltage changes, voltage fluctuations and flicker in public low-voltage supply systems, for equipment with rated current 16 A per phase and not subject to conditional connection. Conform EN61000-3-2 Electromagnetic compatibility (EMC) – Part 3-2: Limits – Limits for harmonic current emissions (equipment input current ≤16 A per phase) Conform EN61000-6-1 Electromagnetic compatibility (EMC) -- Part 6-1: Generic standards - Immunity for residential, commercial and light-industrial environments. Conform EN61000-6-3 Electromagnetic compatibility (EMC) -- Part 6-3: Genericstandards - Emission standard for residential, commercial andlight-industrial environments. Conform FCCPart 15B Electromagnetic compatibility (EMC), Conduction Emission & Radiation Emission. Conform JST/BEC charging cable 5201-0043-01 5201-0031-01 WARRANTYANDSERVICE We guarantee this product to be free of manufacturing and assembly defects for a period of one year from the time of purchase. The warranty only applies to material or operational defects, which are present at t he time of purchase. During that period, we will repair or replace free of service charge for products deemed defective due to those causes. You will be required to produce proof of purchase (invoice or receipt). This warranty is not valid for any damage or subsequent damage arising as a result of misuse, modification or as a result of failure to observe the procedures outlined in this manual. Note: 1. The warranty service is valid in China only. 2. If you need warranty service overseas, please contact your dealer in the first instance, who is responsible for processing guarantee claims overseas. Due to high shipping cost, complicated custom clearance procedures to send back to China. Please understand SkyRC can't provide warranty service to overseas end user directly. 3. If you have any questions which are not mentioned in the manual, please feel free to send email to [email protected] LIABILITY EXCLUSION This charger is designed and approved exclusively for use with the types of battery stated in these Instruction Manual. SKYRC accepts no liability of any kind if the charger is used for any purpose other than that stated. We are unable to ensure that you follow the instructions supplied with the charger, and we have no control over the methods you employ for using, operating and maintaining the device. For this reason we are obliged to deny all liability for loss, damage or costs which are incurred due to the incompetent or incorrect use and operation of our products, or which are connected with such operation in any way. Unless otherwise prescribed by law, our obligation to pay compensation, regardless of the legal argument employed, is limited to the invoice value of those SKYRC products which were immediately and directly involved in the event in which the damage occurred. -3- CE-EMC FCC-VOC Result Title Household and similar electrical appliances –. Safety –. Part 2-29: Particular requirements for battery chargers. This symbol means that you must dispose of electrical devices from the general household waste when it reaches the end of its useful life. Take your charger to your local waste collection point or recycling centre. This applies to all countries of the European Union, and to other European countries with a separate waste collection system. Manufacturedby SKYRCTECHNOLOGYCO.,LTD. www.skyrc.com -4- 7504-0596-02
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement