Sierra Wireless RV50 AirLink RV50 Gateway User Guide

PDF

Έγγραφο

Διαφήμιση

ALEOS 4.5.2

Software Configuration

User Guide for AirLink RV50

4118967

Rev 4

Important

Notice

Limitation of

Liability

Patents

Copyright

Trademarks

Preface

Due to the nature of wireless communications, transmission and reception of data can never be guaranteed. Data may be delayed, corrupted (i.e., have errors) or be totally lost. Although significant delays or losses of data are rare when wireless devices such as the Sierra Wireless modem are used in a normal manner with a well-constructed network, the Sierra Wireless modem should not be used in situations where failure to transmit or receive data could result in damage of any kind to the user or any other party, including but not limited to personal injury, death, or loss of property. Sierra Wireless accepts no responsibility for damages of any kind resulting from delays or errors in data transmitted or received using the Sierra Wireless modem, or for failure of the Sierra Wireless modem to transmit or receive such data.

The information in this manual is subject to change without notice and does not represent a commitment on the part of Sierra Wireless. SIERRA WIRELESS AND

ITS AFFILIATES SPECIFICALLY DISCLAIM LIABILITY FOR ANY AND ALL

DIRECT, INDIRECT, SPECIAL, GENERAL, INCIDENTAL, CONSEQUENTIAL,

PUNITIVE OR EXEMPLARY DAMAGES INCLUDING, BUT NOT LIMITED TO,

LOSS OF PROFITS OR REVENUE OR ANTICIPATED PROFITS OR REVENUE

ARISING OUT OF THE USE OR INABILITY TO USE ANY SIERRA WIRELESS

PRODUCT, EVEN IF SIERRA WIRELESS AND/OR ITS AFFILIATES HAS BEEN

ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR THEY ARE

FORESEEABLE OR FOR CLAIMS BY ANY THIRD PARTY.

Notwithstanding the foregoing, in no event shall Sierra Wireless and/or its affiliates aggregate liability arising under or in connection with the Sierra Wireless product, regardless of the number of events, occurrences, or claims giving rise to liability, be in excess of the price paid by the purchaser for the Sierra Wireless product.

This product may contain technology developed by or for Sierra Wireless Inc. This product includes technology licensed from QUALCOMM

. This product is manufactured or sold by Sierra Wireless Inc. or its affiliates under one or more patents licensed from InterDigital Group and MMP Portfolio Licensing.

Sierra Wireless

, AirPrime

, AirLink

, and the Sierra Wireless logo are registered trademarks of Sierra Wireless.

Windows

and Windows Vista

are registered trademarks of Microsoft

Corporation.

Macintosh

and Mac OS X

are registered trademarks of Apple Inc., registered in the U.S. and other countries.

QUALCOMM

is a registered trademark of QUALCOMM Incorporated. Used under license.

Other trademarks are the property of their respective owners.

Rev 4 Jun.16

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Contact

Information

Sales information and technical support, including warranty and returns

Corporate and product information

Web: sierrawireless.com/company/contact-us/

Global toll-free number: 1-877-687-7795

6:00 am to 6:00 pm PST

Web: sierrawireless.com

4 4118967

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Sierra Wireless AirLink Products . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

About Documentation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Tools and Reference Documents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Gateway Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Toolbar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Configuring your AirLink Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Saving a Custom Configuration as a Template . . . . . . . . . . . . . . . . . . . . . . 17

Applying a Template. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Update the ALEOS Software and Radio Module Firmware . . . . . . . . . . . . . 22

Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

Step 1—Planning Your Update . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

Recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

Step 2—Update the ALEOS Software and Radio Module Firmware . . . .27

Updating Only the Radio Module Firmware . . . . . . . . . . . . . . . . . . . . . . .32

Enterprise LAN Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Configuring Your Gateway for use in a PCI Compliant System . . . . . . . . . . 35

Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37

Home . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

WAN/Cellular . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

LAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

VPN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

GPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Serial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Rev 4 Jun.16

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

About . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

WAN/Cellular Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

Dual SIM Card Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

SIM Slot 1 Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

SIM Slot 2 Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

SIM PIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

Enable the SIM PIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

Change the SIM PIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

Disable the SIM PIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

Unblocking a SIM PIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

Backup APN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

Bandwidth Throttle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

Reliable Static Routing (RSR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75

Dynamic Mobile Network Routing (DMNR) . . . . . . . . . . . . . . . . . . . . . . . . . 80

LAN Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87

Private and Public Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87

DHCP/Addressing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88

Ethernet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96

USB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99

Installing the USB Drivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102

Host Port Routing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103

Global DNS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105

PPPOE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107

Configure the AirLink gateway to Support PPPoE . . . . . . . . . . . . . . . . 108

Configuring a PPPoE Connection in Windows 7 . . . . . . . . . . . . . . . . . . 109

VLAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112

VRRP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114

Host Interface Watchdog . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118

6 4118967

Contents

VPN Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .121

Split Tunnel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121

IPsec . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122

GRE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129

SSL Tunnel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130

VPN Failover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134

Security Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .137

Solicited vs. Unsolicited . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137

Port Forwarding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137

DMZ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142

Port Filtering—Inbound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143

Port Filtering — Outbound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144

Trusted IPs—Inbound (Friends) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145

Trusted IPs—Outbound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147

MAC Filtering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147

Services Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .149

ALMS (AirLink Management Service) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149

ACEmanager . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152

Power Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154

Additional Power Saving Strategies . . . . . . . . . . . . . . . . . . . . . . . . . . . .161

Dynamic DNS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161

Understanding Domain Names . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .166

Dynamic Names . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .166

SMS Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167

Sending SMS Commands to an AirLink Gateway . . . . . . . . . . . . . . . . .168

SMS Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .169

Password Only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .169

Control Only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .170

Gateway Only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .172

Control and Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .178

Rev 4 Jun.16

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

SMS Wakeup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180

SMS Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181

Inbound SMS Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181

Trusted Phone Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 182

SMS Password Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183

SMS > Advanced . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 185

SMSM2M . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 186

Telnet/SSH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 188

Email (SMTP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 189

Management (SNMP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 192

Time (SNTP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 197

Authentication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 198

LDAP Authentication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 199

RADIUS Authentication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200

TACACS+ Authentication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 201

Device Status Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 203

GPS Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 205

GPS Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 205

ALEOS Supported GPS Report Protocols. . . . . . . . . . . . . . . . . . . . . . . . . 206

Before Configuring GPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 206

Enable GPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 207

Global Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 208

Servers 1 to 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 210

Local/Streaming. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 222

Local/Streaming—Local IP Report . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 224

Events Reporting Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 229

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 229

8 4118967

Configuring Events Reporting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230

Configuring Events Reporting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .230

Email . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .231

SMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .233

Relay Link . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .235

SNMP TRAP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .236

GPS Reports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .236

Events Protocol Reports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .237

Turn Off Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .240

Report Data Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .240

Event Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .243

Serial Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .247

Port Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 247

Port Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .248

Reverse Telnet/SSH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .251

UDP Multiple Unicast . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .253

Advanced . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .254

TCP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .256

UDP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .258

PPP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .260

Modbus Address List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 261

Configuring IP to Serial with Answer and Serial to IP. . . . . . . . . . . . . . . . . 262

LED Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 266

Applications Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .267

Data Usage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 267

Garmin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 274

ALEOS Application Framework . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 276

I/O Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .279

AirLink RV50 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .279

Analog inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .279

Digital inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .280

Relay outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .280

Rev 4 Jun.16

Contents

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Current State . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 280

Pulse Count . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 281

Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 282

Transformed Analog . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 282

Admin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 285

Change Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 285

AAF User Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 286

Advanced. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 287

Radio Passthru . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 295

Log. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 296

Radio Module Firmware. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 299

Windows Dial-up Networking (DUN) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 303

Installing a Device Driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 303

Creating a Dial-Up Networking (PPP) Connection . . . . . . . . . . . . . . . . . . 313

Modbus/BSAP Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 323

Modbus Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 323

Configuring AirLink gateways at the Polling Host for Modbus on UDP . 325

Configuring Remote AirLink gateways for Modbus with UDP . . . . . . . . 326

SNMP: Simple Network Management Protocol . . . . . . . . . . . . . . . . . . . . . 329

Management Information Base (MIB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 329

SNMP Traps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 329

Sierra Wireless MIB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 329

AT Commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 355

AT Command Set Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 355

Reference Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 356

Device Updates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 357

Status. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 357

4118967

Contents

WAN/Cellular . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 362

LAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 377

VPN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 379

Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 384

Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 385

GPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 393

Serial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 400

Standard (Hayes) commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .406

I/O. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 411

Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 411

Admin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 415

SMS Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 419

SMS Command format. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 419

List of SMS Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 420

Rev 4 Jun.16

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Q & A and Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 423

ACEmanager Web UI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 423

Templates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 423

Updating the ALEOS Software and Radio Module Firmware . . . . . . . . 424

Poor Wireless Network Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . 426

Connection not working . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 426

LTE Networks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 427

SIM Card is Blocked . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 428

Remote connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 429

Radio Band Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 429

Low Voltage Standby Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 430

Reliable Static Routing (RSR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 430

Inbound Ports Used by ALEOS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 431

Setting for Band . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 432

Ethernet Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 438

LAN Networks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 438

VPN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 438

Port Forwarding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 440

SMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 440

AirLink Management Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 441

GPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 444

Event Reporting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 444

TCP Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 445

TCP/IP and UDP/IP Auto Answer . . . . . . . . . . . . . . . . . . . . . . . . . . . . 445

ALEOS Application Framework (AAF) . . . . . . . . . . . . . . . . . . . . . . . . . 446

Network Operator Switching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 447

Glossary of Terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 449

Index. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 455

12 4118967

Rev 4 Jun.16

1: Introduction

Note: This user guide is intended for the AirLink RV50. If you have an AirLink

ES450 gateway, refer to the ALEOS Software Configuration User Guide for the AirLInk ES450. If you have an AirLink GX450 gateway, refer to the

ALEOS Software Configuration User Guide for the AirLInk GX450.

Overview

ACEmanager™ is the free, web-based utility used to manage and configure the AirLink

device. It is a web application integrated in the

ALEOS™ software that runs on the AirLink gateway. AirLink

Embedded Operating System (ALEOS) is purpose-built to maintain a wireless connection and to configure the gateway to the needs of the system. ACEmanager provides comprehensive configuration, monitoring, and control functionality to all AirLink gateways and routers.

ACEmanager enables you to:

•

Adjust network settings

•

Change security settings

•

Update events reporting and control outputs

•

Update ALEOS software and radio module firmware

•

Copy configuration settings to other AirLink gateways

Since ACEmanager can be accessed remotely over-the-air as well as locally, the many features of ALEOS can be managed from any location.

An ALEOS configuration template can be created using

ACEmanager, after a single device is configured and installed, to program other AirLink gateways with the same configuration values.

This enables quick, accurate deployment of large pools of devices.

Sierra Wireless AirLink Products

This version of ACEmanager is intended to be used with the following products:

•

AirLink RV50

For more information on specific AirLink products, go to www.sierrawireless.com

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

About Documentation

Each chapter in the ALEOS Configuration User Guide describes a section (a tab in the user interface) of ACEmanager.

Chapters in this user guide explain:

•

Parameter descriptions in ACEmanager

•

Relevant configuration details

•

User scenarios for certain sections in the guide.

Tools and Reference Documents

Document

AirLink gateway

Hardware User Guide

ALMS User Guide

Description

This hardware document describes how to:

•

Install the AirLink gateway hardware

•

Connect the radio antennas

•

Connect a notebook computer and other input/output (I/O) devices

•

Interpret the LEDs and indicators on the AirLink gateway.

This document explains how to use AirLink Management Service for the remote management of Sierra Wireless AirLink gateways.

14 4118967

Rev 4 Jun.16

2: Gateway Configuration

To access ACEmanager:

Insert the SIM card, if applicable. Refer to the AirLink gateway hardware user guide for details.

Power on the AirLink gateway.

Launch your browser and enter the IP address and port number http://192.168.13.31:9191

ACEmanager is supported on the latest versions of Internet

Explorer

and Firefox

· User Name: “user” (entered by default) or “viewer

Use the “user” login for configuring or monitoring your gateway.

Logging in as “viewer” only allows you to view the configuration and connection state. You cannot make any configuration changes.

· Default Password: 12345

Note: ACEmanager has a default session idle timeout of 15 minutes. If there is no activity for the idle timeout period, you are redirected to the login

screen. To change the session idle timeout period, see Session Idle Timeout

(minutes) on page 153.

To prevent others from changing the AirLink gateway settings, you

can change the ACEmanager password (see Change Password on page 285).

Figure 2-1: ACEmanager: Main Login screen

After your initial login to ACEmanager, you have the option of displaying the gateway status parameters on subsequent login screens.

In ACEmanager, go to Services > Device Status Screen.

In the Device Status on Login Screen field, select Enable. (For

details, see Device Status Screen on page 203.)

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Figure 2-2: ACEmanager: Main Login screen with Device Status

If you have GPS fields selected on the Device Status screen, but GPS is disabled, the gateway login screen will show GPS Service Disabled.

Toolbar

The buttons on the ACEmanager toolbar are:

•

Software and Firmware: Updates the ALEOS software and the radio module firmware

•

Template:

· Download and save a configuration as a template

· Upload a saved template to apply settings

•

Reboot: Reboots the gateway

•

Refresh All: Refreshes all ACEmanager pages

Configuring your AirLink Gateway

There are three options for configuring the AirLink gateway:

•

Use your browser-based ACEmanager (as detailed in this guide); or

•

Use a terminal emulator application (e.g., Tera Term, PuTTY, etc.) to enter AT commands for many of the configuration options.

•

Use the cloud-based AirLink Management Service application (see www.sierrawireless.com/products-and-solutions/gateway-solutions/alms/ for more details.)

16 4118967

Gateway Configuration

Saving a Custom Configuration as a

Template

If you have a gateway configured to match your requirements, you can use

ACEmanager to download and save that gateway’s configuration as a template and then apply it to other Sierra Wireless AirLink gateways.

Note: Sierra Wireless recommends that templates be created and applied to AirLink gateways running the same version of ALEOS. If you apply a template created using an older version of ALEOS to a gateway running a newer version of ALEOS, settings for newly added features are not updated.

To download and save a custom configuration as a template:

Connect a laptop to the gateway with the configuration you want to save as a template.

In ACEmanager, click the Template button on the toolbar

Figure 2-3: ACEmanager: Template button

The following window appears:

Rev 4 Jun.16

Figure 2-4: ACEmanager: Template window

Use the bottom half of the window to download and save a template.

If desired, enter a Template Name. The file is saved using this name and a. xml file extension. Spaces and special characters are not supported, and if entered, are deleted from the file name.

If no Template name is entered, the file is saved as SWIApplyTemplate.xml.

Choose whether or not to:

· Include Passwords

When Include Passwords is selected, passwords configured in ACEma-

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50 nager (such as the email password, the SMS ALEOS Command password, the Serial PPP password, etc.) are shown in plain text in the template file.

When the template is uploaded to a gateway, the passwords are included and replace any existing password configured on the gateway.

If Include Passwords is not selected, password fields are not included in the template file, and existing passwords persist when the template is uploaded to a gateway.

Note: The ACEmanager login password is not included when you select the Include

Passwords option.

· Include Device Info (selected by default)

When selected, the template file includes a “snap-shot” of the current

Status tab information with the current settings. This could be useful for troubleshooting.

Click Download. The download status appears at the bottom of the window.

Figure 2-5: Download template complete

Once the download is complete, the following window opens:

Figure 2-6: Open or Save the template file

In most cases, you will want to save the file to your computer for uploading to other AirLink gateways, but you also have the option to open the file.

4118967

Gateway Configuration

· Select Save File and click OK—file is saved to your computer (by default to the Downloads folder). If you entered a template name, the file is saved using that name. Otherwise, it is saved under the default name,

SWIApplyTemplate.xml.

· Select Open and click OK—file opens in a text or XML editor as a human readable file. Use this option if you selected Include Device Info when you saved the file and want to view the device information (the text between the

<devicestatus> and </devicestatus> tags is the snap-shot of the Device

Info), or you want to compare this template with another template.

Warning:

Do not attempt to change settings directly in the template file. Changing settings in the template file could result in unexpected behavior in the AirLink gateway.

Alter the template only if you are specifically directed to do so by your distributor or Sierra

Wireless Technical Support.

Tip:

If you want to compare a new template with the previous one, download and save the old template before applying the new one. You can use any 3rd party text comparison tool to check the differences between two templates.

Applying a Template

Note: Sierra Wireless recommends resetting the gateway to the factory default settings before applying the template.

Note: If you are using Internet Explorer 9 to upload the template, see

Templates on page 423 for instructions on configuring the browser’s Internet options to allow the upload.

To upload and apply a template to an AirLink gateway:

Connect the computer (where the template is saved) to the AirLink gateway you want to upload the template to.

Select the Reset Mode:

· Preserve Cellular Authentication Settings—Recommended if you are applying a template remotely using a remote ACEmanager connection (or

ALMS). For a list of preserved settings, see Reset Mode on page 294.

· Reset All— Recommended if you are applying a template locally (i.e your computer is physically connected to the gateway).

In ACEmanager, click the Template button on the toolbar

Figure 2-7: ACEmanager: Template button

Rev 4 Jun.16

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

The following window appears:

Figure 2-8: ACEmanager: Template window

Use the top half of the window to upload and apply a template to your AirLink gateway.

Click Browse... and navigate to the template you want to upload.

Click Open. The template file name appears beside the Browse... button.

Figure 2-9: Apply Template file opened

Click Upload.

When the upload is complete, a Reboot button appears on the window.

20 4118967

Gateway Configuration

Figure 2-10: Template file uploaded

Click Reboot.

10. To confirm that the new template has been applied or to find out which template is currently on a gateway, go to Status > About and check the

Template Name field.

Note: The Template Name field shows the last template applied and does not indicate any configuration changes made since the last template was applied.

Rev 4 Jun.16

Figure 2-11: ACEmanager: Status > About

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Note: If no template has been applied to the gateway since it was set or reset to the factory default settings, the template field is blank.

Update the ALEOS Software and Radio

Module Firmware

To take advantage of new features available in the latest version of ALEOS, update the ALEOS software and radio module firmware on your AirLink gateways.

You can use ACEmanager to update one gateway at a time or AirLink

Management Service (ALMS) to update one or multiple gateways at the same time.

Note: If the update includes a radio module firmware update, the radio module firmware stored on the gateway is also automatically updated. If there is not enough room in the storage, the radio module firmware update fails, so you may need to remove one of the versions stored on the gateway to free up space. For more information, see

Radio Module

Firmware on page 299.

Before You Begin

Once ALEOS 4.5.2 is installed, Low Voltage Standby mode is enabled by default.

The default setting are:

•

Shutdown Voltage: 9.0 V

•

Shutdown Qualification Period: 30 seconds

•

Resume Immediately at Voltage: 10.5 V

If the input voltage is less than 11 V, prior to starting the ALEOS update:

In ACEmanager, go to Services > Power Management.

22 4118967

Gateway Configuration

Figure 2-12: ACEmanager: ALEOS 4.5.0, Services > Power Management

Set the “Force Standby Mode when low voltage present” field to Always.

Configure the appropriate voltage threshold values. (See table

Table 2-1 .)

Click Apply.

Reboot the gateway.

Table 2-1: ALEOS 4.5.0 — Low Voltage Standby

Field Description

Low Voltage

Force Standby Mode when low voltage present

Use this field to select whether or not the gateway goes into Standby mode when low voltage is present. Options are:

•

Never (default)—Low supply voltage does not cause the gateway to go into standby mode

•

Always—If the supply voltage is low, the gateway goes into standby mode regardless of the configured Shutdown Delay after Ignition off or Timed or I/O standby settings.

Rev 4 Jun.16

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Table 2-1: ALEOS 4.5.0 — Low Voltage Standby

Field Description

Shutdown Voltage

(100 milliVolts)

If the incoming voltage to the gateway is below the value set in this field for the period of time set in the

Shutdown Qualification Period (seconds)

field, the gateway goes into standby mode. Valid range is:

•

70—345 hundreds of milliVolts

•

Default is 115.

Enter the value in tenths of Volts. For example, for 11.5 V, enter 115.

The value in this field must be at least 5 milliVolts less than the value in the

Resume immediately at Voltage (100 milliVolts)

field.

Shutdown

Qualification Period

(seconds)

Resume immediately at Voltage

(100 milliVolts)

Set the time period (in seconds) that the voltage to the gateway is below the value set in the

Shutdown Voltage (100 milliVolts) field before the gateway goes into standby mode.

Valid range is:

•

5—3600 seconds

•

Default is 60.

Set the voltage at which the gateway exits standby mode and resumes normal operation.

Valid range is:

•

75—350 hundreds of milliVolts

•

Default is 125.

Enter the value in tenths of Volts. For example, for 12.5 V, enter 125.

The value in this field must be at least 5 milliVolts greater than the value in the

Shutdown

Voltage (100 milliVolts) field.

Standby

Use Standby Mode

Select the type of Standby mode you want to configure

Options are:

•

Disable (default)

•

Timed

•

I/O

•

I/O + Timed

Changes take effect when you click Apply. No reboot is required.

Note: You cannot set this field to I/O or I/O + Timed if the I/O line is already being used by the

Relay Output 1 or by the

Pull-up for I/O 1

Timed

Mode

Select the Mode:

•

Hourly—

Wake Time and Return to Standby

operate on an hourly basis

•

Daily—

Wake Time and Return to Standby operate on an daily basis

•

Custom—Provides the option set a test period to repeat the Wake/Standby cycle

4118967

Gateway Configuration

Table 2-1: ALEOS 4.5.0 — Low Voltage Standby

Field Description

Wake Time

Return to Standby

Set the time (hours:minutes on a 24 hour clock) at which the gateway wakes up.

If you selected Hourly in the Mode field, set the minutes (the hour portion is ignored) and

the gateway wakes up every hour at the configured time.

If you selected Daily in the Mode field, the gateway wakes up every day at the configured

time.

Set the time (hours:minutes on a 24 hour clock) at which the gateway goes into standby mode.

If you selected Hourly in the Mode field, set the minutes (the hour portion is ignored) and

the gateway goes into standby mode every hour at the configured time.

If you selected Daily in the Mode field, the gateway goes into standby mode every day at

the configured time.

Note: There must be at least 5 minutes between the Wake Time

and the Return to

Standby time.

Repeat Period

This field only appears if you select Custom in the Mode

field.

Use this field to configure how often the

Wake Time

Return to Standby

cycle is repeated.

The options are:

•

2 Hours (default)

•

3 Hours

•

4 Hours

•

6 Hours

•

8 Hours

•

12 Hours

I / O

Wake when I/O is

Select the I/O state that causes the gateway to wake. Options are:

•

High (default)

•

Low

Note: If the I /O line is already configured for another purpose, this I/O option is not available.

Rev 4 Jun.16

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Table 2-1: ALEOS 4.5.0 — Low Voltage Standby

Field Description

Delay return to

Standby (seconds)

Processor Power

Savings Mode

Select the delay between the I/O state change and the gateway entering Standby mode (in seconds).

•

Range is 1–43200 (12 hours)

•

Default is 1 second.

Recommended for customers who require the lowest possible active/idle power consumption, for example, in battery or solar powered applications.

Enabling this feature saves energy by reducing performance where possible. The default setting (Disable) favors performance, but increases power consumption.

Step 1—Planning Your Update

Sierra Wireless recommends that you download a template from the gateway(s) before you begin the update process. For instructions, see

Saving a Custom Configuration as a Template on page 17.

For each of the gateways you want to update, make a note of the:

· Device Model

· Radio Module Type

· Radio Module Identifier

· ALEOS Software Version

This information is available in ALMS and in ACEmanager (Status > About).

Figure 2-13: ACEmanager: Status > About

If you are planning to use ACEmanager to do the update:

Go to source.sierrawireless.com

and select your product and mobile network operator to get to the download page for your gateway.

4118967

Rev 4 Jun.16

Gateway Configuration

b. Download the new ALEOS software version for your system. If new radio module firmware is available, it is included with the ALEOS software in a

.zip file.

Important:

Do not install radio module firmware unless you are prompted to do so.

Note: If time of day reset ( page 288

) are configured, and the following events are likely to coincide with the update:

•

The Time of Day reset occurring

Sierra Wireless recommends that you disable these features before beginning the update.

Recommendations

If you have any questions about the update process, contact your authorized

Sierra Wireless distributor before updating the radio module firmware.

Scheduling the update

The update can take up to 30 minutes to complete, depending on the speed of your network connection. The AirLink gateway being updated will be off-line during the update, so take this into account when scheduling the update.

Important:

BE PATIENT! The firmware update can take up to 30 minutes to complete.

Ignore connection time out messages—the update process is still running.

Waiting for the process to complete is faster than troubleshooting the problems that can be caused by interrupting the process midway. (Interrupting the process may result in having to return the gateway to the factory for repairs.)

Step 2—Update the ALEOS Software and Radio

Module Firmware

Using ACEmanager to Update a Single AirLink gateway

To update the ALEOS software and radio module firmware on one AirLink gateway:

Connect the AirLink gateway you want to update to your laptop, launch your browser and enter the URL for the gateway. The default IP address/port for the Ethernet interface is http://192.168.13.31:9191 . If it is a remote gateway, enter the domain name or public IP (WAN) address.

Note: If you are connected to the gateway remotely, any files transferred to the gateway are transferred over-the-air and you may incur data charges.

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

User name: user

Default password: 12345

Click the Software and Firmware link.

The Software and Firmware update window opens.

Note: These instructions show typical Software and Firmware update windows. Details such as the ALEOS version, device model, radio firmware version, etc. may vary, depending on the gateway you are updating.

Figure 2-14: Software and Firmware Update window

The update window gives you the option to update both ALEOS and the radio module firmware, or update only the radio module firmware.

Unless advised otherwise by Sierra Wireless, select ALEOS software (which updates ALEOS and prompts you to update the radio module firmware if a newer version is available for your gateway).

Click Browse... and navigate to the ALEOS software you downloaded from the Sierra Wireless Web site. This is a .bin files named for the gateway and th

ALEOS Software version. For example, RV50_4.5.2.007.bin.

4118967

Gateway Configuration

Rev 4 Jun.16

Figure 2-15: ALEOS file selected in Software and Firmware update window

Click Update.

The ALEOS software update runs automatically and green check marks appear beside each step as it is completed.

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Figure 2-16: ALEOS software update in progress

Important:

Do not disconnect the AirLink gateway from the computer, and do not power cycle or reset the gateway during the update. If you see any error messages, refer to the

Updating the ALEOS Software and Radio Module Firmware on page 424.

If you see the following error message:

Figure 2-17: Low supply voltage error

Either increase the voltage to the gateway, or complete the procedure outlined in

Before You Begin on page 22, and then retry the update.

Depending on the gateway and your Mobile Network Operator, you may be prompted to update the radio module firmware.

If you do not receive a prompt, the radio firmware is up to date. Proceed to

step 10.

Only if prompted to update the firmware, proceed to step 7.

4118967

Gateway Configuration

Figure 2-18: Prompt for Radio Module Firmware

Under Applying, click Browse... and navigate to the radio module firmware file that was included in the .zip file you downloaded. This is a .iso file named for the gateway’s radio module and the mobile network operator’s network (or

“GENERIC”, if it is intended for more than one operator network). For example, MC7354_GENETIC_2830.iso.

Click Open.

The firmware file name appears beside the Browse button.

Click Upload Radio Firmware.

A message appears on the window indicating that the firmware has been successfully uploaded.

Note: Sierra Wireless recommends that you do NOT skip the radio module firmware update unless advised to do so by Sierra Wireless or an authorized distributor. If you choose to skip the radio module firmware update, you’ll see the following warning.

Rev 4 Jun.16

Once the radio module firmware is uploaded, it begins applying the firmware upgrade. On the AirLink gateway, the LED chase begins to indicate that the firmware is being applied.

As indicated on the window, the radio module firmware may take 10 to 20 minutes to upload and install.

Important:

Do not disconnect the AirLink gateway from the computer or reboot the gateway while the firmware update is in progress. During the radio module firmware update, the gateway LEDs flash rapidly in sequence (an LED chase or caterpillar). When the radio module firmware update is complete, the gateway reboots automatically.

Note: When you update the radio module firmware, the firmware stored on the gateway is also updated. If there is not enough room in the storage, the radio module firmware update fails. In that case, first remove one of the versions stored on the gateway to free up space.

For more information, see Radio Module Firmware on page 299.

10. When the update is complete, the AirLink gateway reboots. The Software

Update process window appears.

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

When the reboot is complete, you are returned to the Login screen.

11. After you log in, go to Status > About.

12. Click Refresh.

13. Check the ALEOS Software Version and the Radio Firmware Version fields to confirm that the ALEOS software and the radio module firmware have been updated.

Using AirLink Management Service (ALMS) to Update One or

Multiple AirLink gateways Over-the-Air

You can use AirLink Management Service to update the ALEOS software and radio module firmware over-the-air on one or multiple AirLink gateways.

If you don’t have an ALMS account:

In ACEmanager, go to the Services tab and ensure that ALMS is enabled and the server URL is https://na.m2mop.net/device/msci/com

If this is not the case, enter the correct URL, click Apply and then click Reboot.

Go to www.sierrawireless.com/ALMS for more information.

Updating to ALEOS software with an ALMS account:

Go to airvantage.net

and log in.

Follow the instructions in the online ALMS documentation to update the

ALEOS software and radio module firmware.

Updating Only the Radio Module Firmware

Important:

This feature should be used only if directed by Sierra Wireless or an authorized reseller.

If Sierra Wireless or your authorized reseller directs you to update only the Radio

Module Firmware:

Select the Radio Module Firmware button.

32 4118967

Gateway Configuration

Select the appropriate firmware file for your gateway and click Update. This is a .iso file named for the gateway’s radio module and the mobile network operator’s network (or “GENERIC”, if it is intended for more than one operator network). For example, MC7354_GENETIC_2830.iso.

If you select a file for radio module firmware that is not supported on your gateway, you will see a warning message similar to the following:

Unless you have been advised by Sierra Wireless to do so, we recommend that you do not install an unsupported version of the radio module firmware.

Click Update.

The radio module firmware update runs automatically and green check marks appear beside each step as it is completed.

When the update is complete, the AirLink gateway reboots. The Software

Update process window appears.

Rev 4 Jun.16

When the reboot is complete, you are returned to the Login screen.

After you log in, go to Status > About.

Check the Radio Firmware Version has been updated.

Enterprise LAN Management

You can use AirLink gateways in the following configurations:

•

Standalone with a connection to a single device

When using the AirLink gateway with a single device, ensure that the device is

DHCP enabled.

host

•

With a router

AirLink gateway

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

The router allows several devices to use the AirLink gateway’s connection to the network. When using the AirLink gateway with a router:

· Configure the router to be DHCP enabled.

And either:

· Configure the router to use Network Address Translation (NAT).

· Configure ALEOS (in ACEmanager) to use Host Port Routing. For information on using ALEOS with a router that is not configured to use NAT, see

Host Port Routing on page 103.

Router

AirLink gateway hosts

Note: Other than for VLANs, ALEOS does not provide DHCP addresses to router connected devices.

Over the Air (OTA) Connections

Access AirLink gateways

You can use an OTA connection to access AirLink gateways that are in either configuration described above (stand alone or with a router).

Access connected devices

To use an OTA connection to access a connected device through the AirLink gateway, configure the device in ALEOS as the DMZ or port forwarding destination. For information on inbound OTA connections to the host, see

DMZ on page 142 and

Port Forwarding on page 137.

34 4118967

Rev 4 Jun.16

Gateway Configuration

Configuring Your Gateway for use in a PCI

Compliant System

The credit card industry requires retailers to comply with Payment Card Industry

(PCI) standard to maintain a secure environment when processing payment card transactions. For these transactions, the AirLink gateway acts as a wireless data conduit for routers and PoSs (point-of-sale-terminals) that have been configured for PCI compliance.

Internet

Cellular WAN

AirLink gateway

LAN

Router configured for

PCI compliance

LAN

WAN

Payment Processor

DSL Gateway

Retail store

Wi-Fi

PoS

Wireless Access Point

Figure 2-19: Sample PCI compliant network

The PCI compliant network must be set up so that:

•

The USBnet is on a different subnet from the point-of-sale-terminal.

•

All security protocols must be established from the point-of-sale terminal to the payment processor.

•

Payment card terminals must be on a dedicated LAN or VLAN.

•

The AirLink gateway must be connected to a router that is configured for PCI compliance.

Note: The serial port on the AirLink gateway has no access to the IP data path and does not need to be disabled.

If you are using the AirLink gateway for a payment card industry application, to meet PCI Data Security Standard compliance requirements the following steps must be done by a PCI certified service company.

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

For each gateway:

Connect the AirLink gateway to a router that has been configured for PCI compliance.

Change the password regularly, in accordance with PCI recommendations.

Go to the Admin tab and change the default password.

Do not share the ACEmanager password.

Go to Applications > ALEOS Application Framework and set the ALEOS

Application Framework field to Disable.

36 4118967

3: Status

All of the fields in the Status group are read-only and provide information about the AirLink gateway. Depending on the individual settings and the onboard radio module, the actual status pages may look different than the screen shot shown here.

Tip:

To be sure you are viewing the current status for all fields, it’s a good idea to first click the Refresh button on the upper right side of the screen.

Home

The Home section of the Status tab is the first page displayed when you login to ACEmanager. It shows basic information about the WAN network connection, the mobile network connection, and important information about the gateway.

Note: The fields displayed vary depending on the gateway, the radio module, the type of network the gateway is connected to, and ACEmanager settings.

For details, see

Table 3-1 on page 42.

Rev 4 Jun.16

Figure 3-1: ACEmanager: Status > Home

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Field

Phone Number

Description

The phone number associated with the Mobile Network Operator account. If the Mobile Network

Operator does not allow the account to display the phone number or there is no Mobile Network account for the gateway, “NA” is displayed.

WAN Network

Active WAN IP

Address

Network State

The current IPv4 WAN IP address for the gateway.

Current state of the WAN network connection

•

Network Ready—Connected to a mobile broadband network and ready to transfer data

•

Network Ready Ethernet—Connected to an Ethernet network with a DHCP server.

Note: This connection type has limited feature support.

•

Connecting To Network—Establishing a network connection; wait until the connection is established

•

Not Connected-Wait for Activity—The

Always on connection

field on the WAN/Cellular tab

(Advanced section) is set to Disabled. The gateway connects to the mobile network only when it needs to send or receive data.

•

Data connection failed. Waiting to retry—ALEOS is attempting to reconnect to the mobile broadband network. Ensure that the APN is correct or the account is activated to the ESN for your gateway. Wait until it is able to connect. If you see this status repeatedly or for an extended period of time, contact your Mobile Network Operator.

•

Network Link Down—Unable to connect to the network. Ensure that the APN is correct or the account is activated to the ESN for your gateway. If the problem persists, contact your

Mobile Network Operator.

•

No SIM or Unexpected SIM Status—Unable to read the SIM information; check that the

SIM card is installed correctly.

•

SIM PIN incorrect x attempts left—Wrong SIM PIN entered; enter the correct PIN. If the correct PIN is not entered in the specified number of attempts, the SIM is blocked. Contact your Mobile Network Operator to unblock the SIM.

•

No Service—Unable to connect to the broadband network. Check that the antenna is connected properly. If the problem persists, contact your Mobile Network Operator for information about coverage in your region.

•

Network Authentication Failed—Unable to connect to the network because of invalid authentication data. If the problem persists, contact your Mobile Network Operator.

Note: Messages displayed depend on the gateway, and the type of network.

Mobile (Cellular) Network

Cell Info

Cell information such as the Base Station Identity Code (BSIC), TCH, Received Signal Strength

Indicator (RSSI), Location Area Code (LAC), and the cell ID

For additional information, including cell info for LTE networks, see

*CELLINFO2?

on page 357

and LTE Networks on page 427.

Network

Operator /

Current Network

Operator

Name of the Mobile Network Operator whose network the AirLink gateway is connected to

Note: The roaming operator is only displayed if the home operator allows this.

4118967

Status

Field Description

Radio Technology

Type of service being used by the gateway (e.g. LTE, HSPA+,1xRTT, EV-DO, UMTS, HSPA,

EDGE or GPRS)

If you are connected to a network other than that of your Mobile Network Operator, the network service type indicates that you are roaming (and additional charges may apply).

Network Service

Type

Signal Strength

(RSSI)

Type of network the gateway is connected to (e.g. 4G, 3G, 2G)

Signal Strength and Quality

Different radio technologies have different ways of reporting signal strength and signal quality. The fields displayed in

ACEmanager depend on the type of network it is connected to. For details, see Reported Signal Strength and Quality

Values on page 42.

Received Signal Strength Indicator

The average received signal power measured in the air interface channel

Indicates if there is a strong signal available for the AirLink gateway to connect to

WAN/Cellular

WAN/Cellular provides specific information about the connection including IP address and how much data has been transmitted or received. Some of the information on this screen is repeated on the Home page for quick reference.

42 4118967

Status

Figure 3-2: ACEmanager: Status > WAN/Cellular

Field Description

Cellular IP Address

IPv4 Cellular WAN IP Address

If there is no mobile network connection, 0.0.0.0 is displayed.

WAN/Cellular Network Information

The fields in ACEmanager depend on the type of network it is connected to. Not all the fields described below appear on all gateways.

ESN/EID/IMEI

SIM ID

Electronic Serial Number for the internal radio

Identification number for the SIM card in use

Rev 4 Jun.16

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Field

APN Status

Description

Current APN in use by the network connection

•

(Configured) is a default APN based on the SIM card in use.

•

(User Entered) is a custom APN entered manually into the configuration.

Note: APN is configured on the WAN/Cellular configuration tab.

Number of SIMs present

Primary SIM

Active SIM

IMSI

Cell ID

LAC / TAC

BSIC

Active Frequency Band

PN Offset

WAN Keepalive IP

Address

Keepalive Ping Time

(minutes)

Cellular Network

Watchdog

DNS Proxy

Indicates the number of SIM cards present in the gateway

Indicates which SIM card slot contains the primary SIM card. If two SIM cards are installed, the Primary SIM card is used for network connections.

Indicates which SIM slot contains the Active SIM card (The SIM card that is used for the current data connection.)

International Mobile Subscriber Identity number

Unique number that identifies each base transceiver station (BTS) or sector of a BTS within an LAC

Location Area Code or Tracking Area Code (LTE)

Base Station Identity Code

Current cellular band being used (LTE BAND 4, WCDMA 2100, GSM 450, etc.)

Base station identifier used in CDMA networks

IP address that WAN Keep Alive uses to test the WAN network connectivity (see

Keepalive IP Address on page 67.)

Amount of time between Keepalive pings in minutes

DNS Override

DNS Server 1 (IPv4)

DNS Server 2 (IPv4)

Status of the Cellular Network Watchdog (Enabled or Disabled)

See

Cellular Network Watchdog on page 60.

Determines which DNS server the connected clients use for domain name resolution

•

Enable—DNS Proxy is activated. Connected DHCP clients acquire the AirLink gateway's IP address as their DNS server. The AirLink gateway performs DNS lookups on behalf of the clients.

•

Disable —Connected DHCP clients acquire the DNS servers used by the gateway.

To set this option, see DNS Proxy on page 106.

Override WAN-granted DNS

•

Enabled—Locally configured DNS servers are used.

•

Disabled—DNS servers provided by the active WAN connection are used.

1st DNS server IP address currently in use by the WAN connection to resolve domain names into IP addresses

2nd DNS server IP address

44 4118967

Status

Field Description

Current WAN Time in Use

(minutes)

The time, in minutes, that the gateway has been connected to the current WAN network.

Note: The value of this field is 0 if the gateway is not connected to a WAN mobile network.

Bytes Sent

Bytes Received

Packets Sent

Packets Received

RSR Active Route

Number of bytes sent to the mobile network since system startup or reboot

Number of bytes received from the network since system startup or reboot

Persisted Bytes Sent

Number of bytes sent

The count starts when the gateway first goes on air and persists over reboot. The field resets to zero on reset to factory default settings.

For the RV50, this value is the cumulative traffic for both SIM cards, if more than one

SIM card is present.

Persisted Bytes Received

Number of bytes received

The count starts when the gateway first goes on air and persists over reboot. The field resets to zero on reset to factory default settings.

For the RV50, this value is the cumulative traffic for both SIM cards, if more than one

SIM card is present.

Number of packets sent to the network since system startup or reboot

Number of packets received from the network since system startup or reboot

RSR Test Result

RSR Test TimeStamp

Active route for Reliable Static Routing

•

Primary—Specified network traffic is currently using the configured primary route.

•

Backup—Specified network traffic is currently using the configured backup route.

•

None—RSR is not enabled.

Result of the most recent Object Tracking test

Time of the most recent Object Tracking test

Dynamic Mobile Network Routing (DMNR) is only supported on the Verizon Wireless network.

DMNR Status

DMNR status:

•

Enabled

•

Disabled

DMNR Foreign Agent

Registration Status

This field only appears if DMNR is enabled.

The status of transactions with the Home agent

•

Pass —Connected subnets registered or de-registered successfully

•

Fail—Unable to register or de-register connected subnets

•

Unknown

DMNR Reverse Tunnelling

Agent Status

This field only appears if DMNR is enabled.

Status of the NEMO tunnel

•

Down

Rev 4 Jun.16

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

LAN

This is the status of the local network. It lists information about the network and connected clients.

Figure 3-3: ACEmanager: Status > LAN

Field

Ethernet 1 Status

DHCP Mode

DHCP Status

USB Mode

Connected Clients

IP/MAC table

Description

Speed and duplex status of the connection on Ethernet port 1 (the main Ethernet port). If there is no connection, the value is None.

Status of DHCP mode

•

Server—The AirLink gateway is acting as a DHCP server for all Ethernet connections.

•

Disable—The AirLink gateway is acting as neither a DHCP server or client. All devices connected to the AirLink gateway must have a static LAN IP or use PPPoE.

•

—Default setting is used by authorized AirLink resellers for initial gateway configuration. See

DHCP Status for more information.

Status of DHCP mode (This field only appears when the DHCP mode is.)

•

Server—ALEOS is acting as a DHCP server.

•

Client—ALEOS is acting as a DHCP client.

Which USB port mode is set (USBnet, USB serial, or Disabled)

Number of connected devices that obtained their IP address through DHCP over Ethernet or USBnet. The value in this field does not include devices connected via PPP or PPPoE.

Local IP Address and the MAC Address of connected devices that obtain their IP address through DHCP.

46 4118967

Field

VRRP Enabled

VLAN table

Status

Description

Configuration of the VRRP feature

Identities (Interface name and ID) of the configured VLANs

VPN

The VPN section gives an overview of the VPN settings and indicates whether a

VPN connection has been made.

Figure 3-4: ACEmanager: Status > VPN

Field Description

Incoming Out of Band

Whether Incoming Out of Band traffic is allowed or blocked

Outgoing Management Out of Band

Whether outgoing ALEOS Out of Band traffic is allowed or blocked

Outgoing Host Out of Band

Whether Outgoing Host Out of Band traffic is allowed or blocked

Rev 4 Jun.16

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Field

VPN 1 to 5 Status

Failover - Primary VPN

Description

Status of each VPN connection:

•

Disabled—VPN is disabled (default)

•

Not Connected—The VPN failed to connect. This could be because of a mismatch in the configuration between the client and the server, no data connection on the gateway, etc.

•

Connected—The VPN is connected and ready to transmit traffic.

•

Configuration Error—This status appears when:

•

Two VPNs have both the same Local Address and the same Remote

Address

•

More than one VPN has the remote address set to “0.0.0.0”

Note: This restriction does not apply to the Additional Remote Subnets.

When either of these errors exist, only the first of the conflicting VPNs is operational.

To determine which VPNs are in conflict:

1. Go to Admin > Configure Log.

2. For the VPN Subsystem, ensure that Display in Log is set to Yes. The

Verbosity can be either Info or Debug.

3. Click View Log.

4. The resulting log shows you which VPNs are in conflict.

ID of the primary VPN (for VPN Failover) i.e. VPN 1, VPN 2, VPN 3, VPN 4, VPN 5, or None (Default is None.) Setting persists over reboot.

Failover - Primary VPN

Status

Status of the primary VPN:

•

Disabled—VPN Failover is disabled. (default)

•

Connecting—The VPN is trying to connect to the responder.

•

Active—The VPN tunnel is ready and transferring traffic.

•

Backup—This is currently the backup VPN connection.

•

Failed—Dead Peer Detection (DPD) has determined that the VPN responder is dead, or a ping sent to the VPN host failed.

•

Out of Service—There have been 5 DPD failures within an hour.

Failover - Secondary VPN

ID of the Secondary VPN (for VPN Failover) i.e. VPN 1, VPN 2, VPN 3, VPN 4,

VPN 5, or None (Default is None.) Setting persists over reboot.

Failover - Secondary VPN

Status

Status of the Secondary VPN:

•

Disabled—VPN Failover is disabled. (default)

•

Connecting—The VPN is trying to connect to the responder.

•

Active—The VPN tunnel is ready and transferring traffic.

•

Backup—This is currently the backup VPN connection.

•

Failed—Dead Peer Detection (DPD) has determined that the VPN responder is dead, or a ping sent to the VPN host failed.

•

Out of Service—There have been 5 DPD failures within an hour.

48 4118967

Status

Field

Failover - Overall VPN

Status

Failover - Number of

Primary VPN Failures

Failover - Number of

Secondary VPN Failures

Failover - Number of

Switches to Primary VPN

Failover - Number of

Switches to Secondary

VPN

Description

Status of the overall VPN:

•

Disabled—VPN Failover is disabled. (default)

•

Connecting—One of the VPNs is trying to connect to the responder.

•

Active—One VPN tunnel is currently in use. The backup VPN is available.

•

Backup_Unavailable —One VPN tunnel is currently in use. The backup VPN is not available.

•

Out of Service—Neither the primary nor secondary VPN is operational.

•

N/A—The overall VPN status is temporarily not available. Click Refresh.

Number of times DPD has failed on the primary VPN since the gateway has been rebooted or the “Set VPN Policy” button was clicked

Number of times DPD has failed on the Secondary VPN since the gateway has been rebooted or the “Set VPN Policy” button was clicked

Number of times traffic was switched to the primary VPN since the gateway has been rebooted or the “Set VPN Policy” button was clicked

Number of times traffic was switched to the Secondary VPN since the gateway has been rebooted or the “Set VPN Policy” button was clicked

Security

The security section provides an overview of the security settings on the AirLink gateway.

Rev 4 Jun.16

Figure 3-5: ACEmanager: Status > Security

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Field

DMZ

Port Forwarding

Port Filtering Inbound

Port Filtering Outbound

Outbound Firewall Mode

Trusted Hosts (Friends)

MAC Filtering

IP Reject Count

DMZ IP in use

Description

Status of DMZ (Automatic, Manual, or Disabled)

DMZ defines a single LAN connected device where all unsolicited data should be routed.

Status of port forwarding (Enabled or Disabled)

Status of inbound port filtering (Allowed Ports, Blocked Ports, or Disabled)

Status of outbound port filtering (Allowed Ports, Blocked Ports, or Disabled)

Status of the outbound firewall (Enabled or Disabled)

Status of the Trusted Hosts (Friends) list (Disabled or Enabled)

When this option is enabled, the AirLink gateway only accepts connections from trusted remote IP addresses.

Status of MAC filtering (Enabled or Disabled)

Number of IP addresses that have been rejected

IP address currently in use for DMZ

Services

This section shows the status of AirLink services, including the ACEmanager access level.

Figure 3-6: ACEmanager: Status > Services

4118967

Status

Field Description

ALMS

Remote Access

Local Access

Status of the connection to the AirLink Management Service

ACEmanager remote access (over the WAN link):

•

Disabled (default)

•

HTTPS Only

•

Both HTTP and HTTPS

ACEmanager local access (Ethernet, USBnet, or Serial/DUN):

•

HTTPS Only

•

Both HTTP and HTTPS (default)

Dynamic DNS Service

Service in use for Dynamic DNS translation

Full Domain Name

If the Dynamic DNS Service is configured to use a 3rd party host, the domain name configured is displayed. If the Dynamic DNS Service is configured to use IP Manager, this field does not display.

Use SNTP to update time

Engine Hours

Daily SNTP updates of the system time

Time the engine has been running. Depending on your configuration, this is based on:

•

Voltage on the Power Pin from the vehicle battery (Engine Hours On Voltage Level)

•

Voltage on the Ignition Sense Pin (Engine Hours Ignition Enable)

LDAP Authentication

Status of the LDAP client:

•

Enabled

•

Disabled (default)

RADIUS

Authentication

Status of the RADIUS client:

•

Enabled

•

Disabled (default)

TACACS+

Authentication

Status of the TACACS+ client:

•

Enabled

•

Disabled (default)

Rev 4 Jun.16

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

GPS

The GPS (Global Positioning System) tab provides AirLink gateway location and movement information for use with tracking applications.

Figure 3-7: ACEmanager: Status > GPS

Field Description

GPS Service

Status of the GPS Service

•

Enabled

•

Disabled

The remainder of the fields only appear if GPS Service is enabled.

GPS Fix

Satellite Count

Latitude

Longitude

Heading

Status of the GPS fix

•

No GPS Fix

•

GPS Fix Acquired

•

GPS WAAS Fix— Wide Area Augmentation System GPS fix

Number of satellites the GPS receiver detects

Latitude of the GPS receiver

Click the Map link to view the current location of the gateway, using Google Maps™.

Longitude of the GPS receiver

Speed (km/h)

Direction in which the AirLink gateway is moving. No configuration is needed for Heading or Speed; these are calculated automatically.

Speed (in kilometers per hour)

52 4118967

Status

Serial

Figure 3-8: ACEmanager: Status > Serial

Field

Serial Port

Serial Reserved by

External

Serial Port Mode

Login reverse telnet

TCP Auto Answer

Description

Status of the serial port:

•

Enabled—The serial port is functional (default).

•

Disabled — The serial port has been manually disabled. To enable the serial port, go to

Port Configuration on page 247.

Reservation status of the serial port:

•

Enabled—The serial port is reserved for ALEOS Application Framework (ALEOS AF), and cannot be used for any other serial-related ALEOS features.

•

Disabled — The serial port is available for non-ALEOS AF, serial-related ALEOS features.

To reserve the serial port for ALEOS AF, go to Applications > ALEOS Application

Framework > Serial Port Reserved. (See

ALEOS Application Framework on page 276.)

Default power-up mode for the serial port. When the AirLink gateway is power-cycled, the serial port enters the mode specified by this command after 5 seconds.

This field only appears when reverse telnet is selected as the Serial Port Mode.

Status of login for reverse telnet. For more information, see

Reverse Telnet/SSH on page 251.

This parameter determines how the AirLink gateway responds to an incoming TCP connection request. The AirLink gateway remains in AT Command mode until a connection request is received. DTR must be asserted (S211=1 or &D0) and the gateway must be set for a successful TCP connection. The AirLink gateway sends a “RING” string to the host. A

“CONNECT” sent to the host indicates acknowledgment of the connection request and the

TCP session is established.

•

Disabled (default)

•

Enabled

Rev 4 Jun.16

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Field

UDP Auto Answer

How UDP auto answer mode is configured

•

Disabled (default)

•

Enabled

Serial bytes sent

Number of bytes sent over serial port to host

Serial bytes received

Number of bytes received over serial port from host

Serial Signal Level

Description

Status of the following parameters related to the host signal level:

•

DCD—Data Carrier Detect—Control signal to the PC

•

DTR—Data Terminal Ready—Used to establish a connection

•

DSR—Data Set Ready—Used to establish a connection

•

CTS—Clear to Send—Data flow control

•

RTS—Request to Send—Data flow control

Each parameter can have a value of LOW (signal not asserted) or HIGH (signal being asserted).

The first three parameters (DCD, DTR, and DSR) may be helpful for troubleshooting. If the values shown for these parameters are not as expected:

Press Refresh to ensure you have the latest values.

Check the cable connections.

Note: ACEmanager does not update dynamically. Press Refresh to view the current values.

Applications

The Applications section of the Status group provides information on the status of the Garmin gateway and data service.

Figure 3-9: ACEmanager: Status > Applications

4118967

Status

Field

Data Service

Available RAM (KB)

Available Flash (KB)

CPU Load

(Last 15 minutes)

Description

Data Service field displays “Available (under usage limit)” if the configured usage limit has not been exceeded.

Available RAM in kilobytes (1000 bytes), updated every 30 seconds

Available Flash on the user partition in kilobytes (1024 bytes), updated every 30 seconds

CPU load, averaged over the last 15 minutes and updated every 30 seconds

The CPU load relates to how many applications are attempting to execute in parallel over the 15-minute period. If the load is greater than 1, some applications are waiting for CPU capacity to become available and may be delayed in launching.

Whether ALEOS Application Framework is enabled or disabled

ALEOS Application

Framework

Serial Port Reserved

Reservation of the serial port:

•

Disable (default)

•

Enable

QCOM DM Port

Resource Reserve

Reservation of the QCOM DM port:

•

Disable (default)

•

Enable

About

The About section of the Status group provides basic information about the

AirLink gateway.

Rev 4 Jun.16

Figure 3-10: ACEmanager: Status > About

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Field

Device Model

Description

Model of the gateway (e.g.,RV50)

Radio Module Type

Radio Module Identifier

Model number of the internal radio module (e.g. MC7304, MC7354)

Identifier for the internal mobile radio module

Radio Firmware Version

Firmware version in the radio module

PRI ID

Product Release Instructions ID number

Global ID

Ethernet Mac Address

Device ID used by ALEOS to identify itself for various management applications

MAC address of the main Ethernet port

ALEOS Software Version

Version of ALEOS software running on the AirLink gateway

ALEOS Build number

Build number for the ALEOS Software

AirLink gateway’s hardware configuration

Device Hardware

Configuration

Boot Version

Version of boot code installed on the gateway

MCU Firmware Version

MSCI Version

Template Name

Version of micro controller unit (MCU) firmware installed on the gateway

MSCI version of the ALEOS internal configuration database

If you have installed a custom-named template, the name appears here. Otherwise, the field is blank.

56 4118967

Rev 4 Jun.16

4: WAN/Cellular Configuration

The WAN/Cellular tab in ACEmanager allows you to view and modify mobile network connection settings. The settings available depend on the gateway model and the radio module.

The first time you power up the gateway on its home network, it automatically begins the activation/provisioning process and attempts to connect to the network. This process typically takes 5–10 minutes. If the gateway does not automatically connect to the

network, see Network Credentials on page 59.

Note: The fields displayed vary depending on the ACEmanager settings.

Dual SIM Card Support

The AirLink RV50 gateway has two SIM card slots and is capable of supporting a primary and secondary SIM card. By default, the SIM card in the upper slot (slot 1) is the primary SIM card. To configure which slot holds the primary SIM card, see

Primary SIM on page 58.

When the RV50 powers up or reboots, it detects how many and which

SIM cards are inserted. It connects to the cellular network using the primary SIM card, if present. If there is no SIM card in the primary

SIM card slot, the RV50 connects to the cellular network using the secondary SIM card.

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Slot 1

Slot 2

Field

Multi SIM

Active SIM

Primary SIM

Figure 4-1: ACEmanager: WAN/Cellular

Description

Indicates which SIM slot contains the Active SIM card (The SIM card account that is used for the current data connection.)

You can also use the

*ACTIVESIM?

to query the SIM card slot that contains the Active

SIM.

Select which SIM card slot contains the primary SIM card. If two SIM cards are installed, the Primary SIM card is used for network connections. Options are:

•

Slot 1—The SIM card in Slot 1 (upper slot) is the primary SIM card. (default)

•

Slot 2—The SIM card in Slot 2 (lower slot) is the primary SIM card.

If there is no SIM card in the primary SIM card slot, the gateway connects to the cellular network using the secondary SIM card.

You can also use the

*PRIMARYSIM

to query or set the primary SIM card slot.

Indicates whether or not a SIM card is inserted in SIM slot 1 (the upper SIM slot)

You can also use the

*SIM1PRESENT?

to query the presence of a SIM card in slot 1.

Indicates whether or not a SIM card is inserted in SIM slot 2 (the lower SIM slot)

You can also use the

*SIM2PRESENT?

to query the presence of a SIM card in slot 2.

4118967

WAN/Cellular Configuration

Field

Description

Network Credentials

RX Diversity

Network Roaming

Preference

Allows two antennas to provide a more consistent connection

•

Disable

•

Enable (default)

If you are not using a diversity antenna, diversity should be disabled.

Allows you to control whether or not roaming (connecting to a mobile broadband network other than that of your Mobile Network Operator). Options are:

•

Automatic—The device connects to the home network if it is available and to another Mobile Network Operator’s network if the home network is not available

(for example you are outside the coverage area).

Note: Roaming charges may apply.

•

Home Only—The device only connects to the home network. If the home network is not available (for example, if you are outside the coverage area) the device does not connect until the home network is available again.

Keep Alive (See

Keepalive on page 66.)

Advanced

Response to Incoming

Ping

When a ping is received by the gateway from a remote location, the Response to

Incoming Ping redirects it to the selected location.

•

No response: The incoming ping is completely ignored

•

ALEOS Responds (default): ALEOS returns to the Ping response.

•

Pass to Host: The ping is forwarded to the DMZ host with any response from the host forwarded back to the OTA location. If no host is connected, there is no ping response.

Note: Some Mobile Network Operators may block all ICMP traffic on their network.

When ICMP is blocked by the operator, a ping sent to the gateway from a remote location is not received.

Network Watchdog

Timer

Network Watchdog (minutes)

If there is no WAN connection for the time configured in this field, the gateway reboots.

Options are:

•

Disable—When this field and the Network Watchdog Timer field are set to Disable,

the gateway never reboots as a result of lack of network connectivity.

•

5 Minutes

•

10 Minutes

•

15 Minutes

•

30 Minutes

•

45 Minutes

•

1 Hour

•

2 Hours (default)

•

3 Hours

•

4 Hours

Rev 4 Jun.16

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Field

Set Carrier (Operator)

Selection

Cellular Network

Watchdog

Description

Manually specify an operator. Enter the desired parameters in the following format: mode[,format[,oper]]

•

mode= 0: Automatic — any affiliated carrier [default]

•

mode= 1: Manual — use only the operator <oper> specified

•

mode= 4: Manual/automatic — if manual selection fails, goes to automatic mode

•

format= 0: Alphanumeric (“name”)

•

format= 2: Numeric

•

oper=”name”

SIM Slot 1 Configuration

To configure the SIM card in slot 1:

In ACEmanager, go to WAN/Cellular > SIM Slot 1 Configuration.

Field

Network Credentials

Figure 4-2: WAN/Cellular > SIM Slot 1 Configuration

Use the information in the following table to configure the SIM card in slot 1.

Description

Note: If the gateway does not automatically connect to the network, you may need to manually configure your APN using the User Entered APN field. You may also need to contact your Mobile Network Operator to confirm the APN and activation status of your gateway.

APN in Use

This field only appears for the Active SIM.

The APN in use for the current mobile network connection.

When you power on the AirLink gateway, the APN the gateway is using for authentication on the mobile network is displayed.

•

If a User Entered APN is configured, the User Entered APN is displayed.

•

If there is no User Entered APN configured, an automatically-selected APN is displayed.

•

When the Backup APN is configured, the APN in Use displays the configured

Backup APN when it is being used for authentication on the mobile network.

If ALEOS is unable to find the appropriate APN to use (No APN found), contact your

Mobile Network Operator for the APN and enter it in the User Entered APN on page 64

field.

Rev 4 Jun.16

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Field

User Entered APN

Description

The APN entered in this field takes priority over the automatically-selected APN.

Enter the APN in this field (maximum 100 characters).

Click Apply.

Click Reboot.

Note: If you reset the gateway to factory defaults, you have the option to preserve the custom APN, if entered. See

Reset Mode on page 294.

SIM PIN

Click this button to configure the PIN for the SIM card in SIM slot 1. For more information, see

SIM PIN on page 68. By default, the gateway does not use a SIM PIN

for the SIM in slot 1.

Advanced

LTE Authentication

Mode

Network User ID

Specifies the authentication method to use when connecting to a mobile network

Options are:

•

NONE

•

CHAP

•

PAP (default)

Network User ID

The login that is used to login to the mobile network, when required.

•

Maximum 128 characters

Network Password

Network Password is the password that, when required, is used to login to the mobile network.

•

Maximum 30 characters

APN Backup (For information on configuring APN Backup for SIM Slot 1, see

Backup APN on page 71.)

64 4118967

WAN/Cellular Configuration

SIM Slot 2 Configuration

To configure the SIM card in slot 2:

In ACEmanager, go to WAN/Cellular > SIM Slot 2 Configuration.

Field

Network Credentials

Figure 4-3: WAN/Cellular > SIM Slot 2 Configuration

Use the information in the following table to configure the SIM card in slot 2.

Description

APN in Use

This field only appears for the Active SIM.

The APN in use for the current mobile network connection.

When you power on the AirLink gateway, the APN the gateway is using for authentication on the mobile network is displayed.

•

If a User Entered APN is configured, the User Entered APN is displayed.

•

If there is no User Entered APN configured, an automatically-selected APN is displayed.

•

When the Backup APN is configured, the APN in Use displays the configured

Backup APN when it is being used for authentication on the mobile network.

If ALEOS is unable to find the appropriate APN to use (No APN found), contact your

Mobile Network Operator for the APN and enter it in the User Entered APN field.

Rev 4 Jun.16

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Field

User Entered APN

Description

The APN entered in this field takes priority over the automatically-selected APN.

Enter the APN in this field (maximum 100 characters).

Click Apply.

Click Reboot.

Note: If you reset the gateway to factory defaults, you have the option to preserve the custom APN, if entered. See

Reset Mode on page 294.

SIM PIN

Click this button to configure the PIN for the SIM card in SIM slot 2. For more information, see

SIM PIN on page 68. By default, the gateway does not use a SIM PIN

for the SIM in slot 2.

Advanced

LTE Authentication

Mode

Network User ID

Specifies the authentication method to use when connection got a mobile network

Options are:

•

NONE

•

CHAP

•

PAP (default)

Network User ID

The login that is used to login to the mobile network, when required.

•

Maximum 128 characters

Network Password

Network Password is the password that, when required, is used to login to the mobile network.

•

Maximum 30 characters

APN Backup (For information on configuring APN Backup for SIM Slot 2, see

Backup APN on page 71.)

Keepalive

If the AirLink gateway does not receive a valid packet for a specified time,

Keepalive tests the connection to the mobile network by pinging a configured IP address. Keepalive is only recommended if you have a remote terminated device that infrequently communicates to the network or if you have experienced issues over time where the device can no longer be reached remotely.

66 4118967

WAN/Cellular Configuration

Figure 4-4: ACEmanager: WAN/Cellular > Keepalive

Field

Keepalive IP

Address

Description

The IP address that the AirLink gateway pings to determine if there is Internet connectivity and to make sure the IP address is accessible.

Enter the IP address or fully qualified domain name for the AirLink gateway to ping to keep itself alive

(online). Options are:

•

IP address

•

Domain name

You can also use

*IPPINGADDR to set this parameter.

Rev 4 Jun.16

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Field

Keepalive

Ping Time

(minutes)

Force

Keepalive

Ping

Description

The amount of time the AirLink gateway goes without receiving a valid packet before the first

Keepalive ping is sent. Options are:

•

0—Disable Keepalive ping (default)

•

1–255 minutes

Most applications work well with an interval of 15 to 60 minutes.

If the first ping fails, the AirLink gateway sends four additional pings. If all five pings fail, the AirLink gateway reboots. After rebooting, the AirLink gateway waits 60 minutes before sending another

Keepalive ping (regardless of the setting in this field). This prevents frequent rebooting (based on the

Keepalive Ping Time setting) if the IP address used for the Keepalive ping is not accessible.

Note: Using Keepalive ping may accrue data charges. Each individual ping is approximately

98 bytes (196 bytes for ping sent plus ping response).

You can also use

*IPPING

to set this parameter.

Determines if the ping should be sent even if IP traffic is received during the Keepalive ping interval.

Options are:

•

Disable (default)

•

Enable

Keepalive ping (regardless of the setting in this field). This prevents frequent rebooting (based on the

Keepalive Ping Time setting) if the IP address used for the Keepalive ping is not accessible.

You can also use

*IPPINGFORCE to configure this parameter.

SIM PIN

If you have a SIM card with a PIN configured, you can configure ALEOS to enter the PIN on reboot, so human intervention is not required.

This feature has two requirements:

•

A PIN-locked SIM card—Contact your Mobile Network Operator to ensure that they support this feature and to obtain a PIN-locked SIM card and PIN.

•

The SIM PIN feature in ACEmanager must be enabled. See

Enable the SIM

If the AirLink gateway has a PIN-locked SIM installed and this feature is not enabled in ACEmanager, the AirLink gateway is unable to go on air and the

Network Status field on the Status > Home screen displays the message “SIM

PIN incorrect, # attempts left”.

Enable the SIM PIN

To enable the SIM PIN in ALEOS:

In ACEmanager, go to WAN/Cellular.

Click the SIM PIN button. The following pop-up window appears.

68 4118967

WAN/Cellular Configuration

Select Enable.

Enter the PIN (obtained from your Mobile Network Operator) twice and click

Save.

Reboot the AirLink gateway.

After rebooting:

•

The AirLink gateway uses the configured PIN on subsequent re-boots.

•

The SIM PIN pop-up window shows the default settings. Don’t change is selected and the SIM PIN fields are blank. “Don’t change” indicates that the

PIN is used in the same way on every boot.

Note: If you enter an incorrect PIN, the AirLink gateway is unable to go on air, and the

Network Status field on the Status > Home screen displays “SIM PIN incorrect, # attempts left”. The failed PIN is not retried on subsequent reboots to prevent exhausting the available number of retries with repeated attempts with an incorrect PIN.

Change the SIM PIN

To change the SIM PIN:

In ACEmanager, go to WAN/Cellular.

Click the SIM PIN button. The following pop-up window appears.

Rev 4 Jun.16

Select Enable.

Enter the new PIN twice and click Save.

Reboot the AirLink gateway.

After rebooting:

•

The AirLink gateway uses the configured PIN on subsequent re-boots.

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

•

The SIM PIN pop-up window shows the default settings. Don’t change is selected and the SIM PIN fields are blank. “Don’t change” indicates that the

PIN is used in the same way on every boot.

Note: If you enter an incorrect PIN, the Network Status field on the Status > Home screen displays “SIM PIN incorrect, # attempts left”. The failed PIN is not retried on subsequent reboots to prevent exhausting the available number of retries with repeated attempts using an incorrect PIN.

Disable the SIM PIN

To disable the SIM PIN:

In ACEmanager, go to WAN/Cellular.

Click the SIM PIN button. The following pop-up window appears.

Select Disable.

Enter the PIN twice and click Save.

If you enter an incorrect PIN or no PIN, the feature will not be disabled.

Reboot the AirLink gateway.

After rebooting:

•

The AirLink gateway no longer uses the stored PIN on subsequent re-boots.

•

The SIM PIN pop-up window shows that the feature is Disabled.

Unblocking a SIM PIN

When you enable, change or disable a SIM PIN, you have a set number of attempts to enter the correct PIN, depending on your Mobile Network Operator. If the correct PIN is not entered in the alloted number of attempts, the SIM PIN becomes blocked and you need a PUK code to unblock it.

To unblock a SIM PIN:

Contact your Mobile Network Operator to obtain a PUK code.

In ACEmanager, go to WAN/Cellular.

Click the SIM PIN button.

When the PIN is blocked, an additional field (Enter SIM Unblock Code) appears.

4118967

WAN/Cellular Configuration

Rev 4 Jun.16

Select Enable.

Enter the new PIN code.

Enter the PUK and click Save.

Be careful when entering the PUK. You have a limited number of attempts to enter the correct PUK (generally 10) before the SIM card is disabled. If the

PUK does not unblock the SIM PIN after the first few attempts, contact your

Mobile Network Operator.

If you have exhausted all the alloted attempts to enter the correct PUK, the

Mobile Network Operator may give you a new SIM card, or a new code to enable your existing SIM card. AirLink products do not support this type of code. To enter the code:

Remove the SIM card from your AirLink gateway (following the instructions in the AirLink gateway Hardware User Guide) and insert it in a cell phone that accommodates a MiniSIM (2FF) card.

b. Enter a new code provided by the Mobile Network Operator and then return the SIM card to the AirLink gateway.

Backup APN

This feature enables you to configure a backup APN to be used as a backup network connection mechanism, only if the primary APN is not available. When it is enabled, the gateway connects to the backup APN only if it is unable to connect to the primary APN.

Note: Switching to the backup APN can take five minutes or more, depending on the gateway. If the gateway is always connecting to the backup APN, check the primary APN to ensure that it is configured correctly.

To configure a backup APN:

Go to WAN/Cellular > APN Backup.

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Figure 4-5: ACEmanager: WAN/Cellular > Slot 1 Configuration > APN Backup

Enter the backup APN (maximum 100 characters).

Select the Network Authentication Mode. The options are:

· PAP (default)

· CHAP

· NONE

Enter the Network User ID and Password, if these are required for the wireless network.

Click Apply.

Bandwidth Throttle

This feature helps you manage your data account by allowing you to configure the

AirLink gateway to restrict the real-time available bandwidth. You can:

•

Place limits on the uplink traffic, downlink traffic, or both

•

Allow for burst of traffic on the uplink, downlink, or both, while still maintaining the over-all desired bandwidth limit

Traffic that exceeds the limits is dropped. Status fields keep running tallies of data sent and received and the number of uplink and downlink packets dropped.

4118967

WAN/Cellular Configuration

Figure 4-6: ACEmanager: WAN/Cellular > Bandwidth Throttle

Field

Bandwidth Throttle

Mode

Description

Downlink Bandwidth

(Kbps)

Allows you to Enable or Disable the feature

Default is Disable.

The maximum downlink bandwidth in Kilobits per second (Kbps)

This is the long-term bandwidth limit. Options are:

•

0–512000 (500 Mbps)

Default is 25600.

0 = feature disabled for downlink traffic

Rev 4 Jun.16

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Field

Maximum Downlink

Burst Size (Kb)

Description

Maximum size for bursts of downlink traffic in Kilobits (Kb)

This field allows the AirLink gateway to handle temporary bursts of downlink traffic without dropping packets. When the actual downlink traffic is less than the value configured in the

Downlink Bandwidth (Kbps)

field, ALEOS collects credits that can be used for bursty traffic. The value in this field is the maximum amount of credit that can be collected.

Options are:

•

64–512000 (500 Mb)

Default is 51200.

Note: Sierra Wireless recommends that the Maximum Downlink Burst Size be set at 2x the value configured in the

Downlink Bandwidth (Kbps)

field. If the Maximum Downlink

Burst Size is set at more than 60x the value configured in the Downlink Bandwidth (Kbps)

field, the bandwidth throttle feature is disabled for downlink traffic.

Maximum Monthly

Downlink Data (MB)

Uplink Bandwidth

(Kbps)

An estimate of the maximum monthly downlink data in Megabytes (MB), based on the

value set in the

Downlink Bandwidth (Kbps) .

Maximum monthly downlink data (MB) = Downlink bandwidth x 2592000 ÷ 8192

Where:

2592000 is the number of seconds in a month (30 days/month)

1 MB = 1024 KB; 1024 x 8 = 8192 Kb/MB

The maximum uplink bandwidth in Kilobits per second (Kbps)

This is the long-term bandwidth limit. Options are:

•

0–204800 (200 Mbps)

Default is 12288.

0 = feature disabled for uplink traffic

Maximum Uplink Burst

Size (Kb)

Maximum size for bursts of uplink traffic in Kilobits (Kb)

This field allows the AirLink gateway to handle temporary bursts of uplink traffic without dropping packets. When the actual uplink traffic is less than the value configured in the

Uplink Bandwidth (Kbps)

field, ALEOS collects credits that can be used for bursty traffic.

The value in this field is the maximum amount of credit that can be collected. Options are:

•

32–204800 (200 Mb)

Default is 24576.

Note: Sierra Wireless recommends that the Maximum Uplink Burst Size be set at 2x the

value configured in the Uplink Bandwidth (Kbps)

field. If the Maximum Uplink Burst Size is

set at more than 60x the value configured in the Uplink Bandwidth (Kbps) field, the

bandwidth throttle feature is disabled for uplink traffic.

Maximum Monthly

Uplink Data (MB)

Downlink Bytes Rcvd

An estimate of the maximum monthly uplink data i in Megabytes (MB), based on the value

set in the

Uplink Bandwidth (Kbps)

Maximum monthly uplink data (MB) = Uplink bandwidth x 2592000 ÷ 8192

Where:

2592000 is the number of seconds in a month (30 days/month)

1 MB = 1024 KB; 1024 x 8 = 8192 Kb/MB

Number of downlink bytes received

The value is updated every 30 seconds, and is reset to zero on gateway reboot or reset to factory default settings.

74 4118967

WAN/Cellular Configuration

Field

Downlink Packets

Rcvd

Downlink Packets

Dropped

Uplink Bytes Sent

Uplink Packets Sent

Uplink Packets

Dropped

Description

Number of downlink packets received

The value is updated every 30 seconds, and is reset to zero on gateway reboot or reset to factory default settings.

Number of downlink packets dropped because the limits set in Downlink Bandwidth

(Kbps)

and Maximum Downlink Burst Size (Kb) have been exceeded

The value is updated every 30 seconds, and is reset to zero on gateway reboot or reset to factory default settings.

Number of uplink bytes sent

The value is updated every 30 seconds, and is reset to zero on gateway reboot or reset to factory default settings.

Number of uplink packets sent

The value is updated every 30 seconds, and is reset to zero on gateway reboot or reset to factory default settings.

Number of uplink packets dropped because the limits set in Uplink Bandwidth (Kbps)

and

Maximum Uplink Burst Size (Kb) have been exceeded

The value is updated every 30 seconds, and is reset to zero on gateway reboot or reset to factory default settings.

Reliable Static Routing (RSR)

Reliable Static Routing enables you to force specified traffic to use different routing rules (rather than the default, which is usually cellular) to direct specified traffic (from or to either the AirLink gateway or a connected device) to a designated primary route. If the primary route fails, the specified traffic uses a backup route.

First, you designate specific traffic to use the primary route, based on the destination IP address and subnet mask. A configured Tracking Object Test verifies the validity of the primary route. If the test fails, the backup route is used.

The Tracking Object Test continues to run and as soon as it returns a “Pass”, traffic is switched back to the primary route.

You can direct the traffic to a network or to an individual host.

Cellular

(Backup route)

Internet

Ethernet

(primary route)

Connected device

AirLink gateway

Figure 4-7: RSR directed to a destination network

Network Management Center

Network IP: 64.100.20.128

64.100.20.129

64.100.20.130

255.255.255.252

Rev 4 Jun.16

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Connected device

Cellular

(Backup route)

Network Management Center

Internet

64.100.20.128

255.255.255.255

Ethernet

(primary route)

AirLink gateway

Figure 4-8: RSR directed to a destination IP address (individual host)

In a business continuity application where the router also has a routable IP

address from a wireline gateway connection (as shown in Figure 4-9

) the IT administrator may prefer to use that lower cost connection for data sourced from the AirLink gateway, such as SNMP or ALMS data. When reliable static routing is configured, the Tracking Object tests the validity of the primary route and data from the AirLink gateway is transmitted through the primary route (in this example, the wireline connection). If the tracking object determines that the primary route is down, data is transmitted through the backup (in this example, the wireless connection).

Private mode

RSR destination IP (e.g. 64.100.20.128)

Internet

Tracking object test IP (e.g. 8.8.8.8)

Wired WAN connection primary route

Wireless WAN connection

Backup route

Wireline Gateway

Tracking object

AirLink gateway

Primary route

Backup route

Tracking object

Figure 4-9: Private Mode with Reliable Static Routing

Sierra Wireless recommends a Private Mode network as the most reliable configuration to use in a business continuity failover application as defined in the

AirLink Hardware User Guide (or

Figure 4-9 ) with Reliable Static Routing and

Reverse Telnet. For more information, see

Private and Public Mode on page 87.

To configure Reliable Static Routing:

Connect the hardware as shown in Figure 4-9

4118967

Rev 4 Jun.16

WAN/Cellular Configuration

Use the Tracking Object to test the connection:

In ACEmanager, go to WAN/Cellular > Reliable Static Route (RSR).

Figure 4-10: ACEmanager: WAN/Cellular > Reliable Static Route (Tracking Object)

b. Under Tracking Object, enter the Test IP address, using a host behind the gateway that has a reliable IP address, such as 8.8.8.8.

From the drop-down menu, select Ethernet 1 as the Test Interface.

d. Leave the default values for the Test Interval, Test Timeout, and

Maximum number of retries.

In the Enable/Disable Tracking Object field, select Enable.

Click Apply.

g. The Tracking Object pings the Test IP address configured in step b

. In

ACEmanager go to Status > WAN/Cellular and note the result in the RSR

Test Result field.

Disable Tracking Object.

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Figure 4-11: ACEmanager: WAN/Cellular > Reliable Static Route (RSR)

Note: Configure all the other fields before setting the Enable/Disable Reliable Static

Routing field. Once you enable RSR, some fields on this page are not editable.

Select the interfaces for the primary and backup routes. The options are:

· Ethernet 1 (default for primary route)

· USB

· Cellular (default for backup route)

If you select Ethernet 1, you are given the option to enter a gateway IP address that is used as the next hop for reaching the destination network.

· If the Tracking Object test completed in

step 2 was successful, leave this

field at the default value (0.0.0.0).

· If the Tracking Object test completed in

step 2 failed, enter the gateway IP

address in this field.

Set the Destination IP/Network and Destination Subnet Mask.

To configure the RSR destination as a network for this example, enter:

· 64.100.20.128 in the Destination IP/Network field.

1. This applies to both the primary and the Backup interface.

4118967

Rev 4 Jun.16

WAN/Cellular Configuration

· 255.255.255.252 in the Destination Subnet Mask field.

To configure the RSR destination as an individual host for this example, enter:

· 64.100.20.128 in the Destination IP/Network field.

· 255.255.255.255 in the Destination Subnet Mask field.

Set the Tracking Object (Tracking Object 1 or No Tracking Object). Normally, you would select Tracking Object 1 from the drop-down menu.

Under Tracking Object, leave the Enable/Disable Tracking Object set at

Disable until you finish configuring the other Tracking Object fields.

Enter the Test IP address (normally an IP address within the Traffic Selection

Criteria Network/Subnet).

From the drop-down menu, select the desired Test Interface (normally the same interface as the primary route). Options are:

· Ethernet 1

· USB

· Cellular

10. Enter the Test Interval in seconds. This is the interval between Tracking

Object Tests.

For most applications, the default values for the Test Interval, Test Timeout, and Maximum number of retries should be fine.

If you want to change these values, be aware of the following:

· Selecting a short test interval increases network traffic and may lead to false failures if the network is busy.

· Selecting a long test interval may mean that traffic does not switch to the secondary route quickly enough when the primary route fails.

· The test interval must be greater than the product of Test Timeout x

Maximum number of Test Retries.

[Test Interval] > [Test Timeout] x [Maximum number of Retries]

11. Enter the Test Timeout in seconds. This is the time to wait for a response. If this time expires before a response is received, the test attempt fails.

12. Enter the Maximum number of Test Retries. If the first Tracking Object Test fails, this is the number of times the gateway sends additional test messages

(without receiving a response) before it declares the test as failed and switches the specified traffic to the backup network.

13. In the Enable/Disable Tracking Object field, select Enable.

14. In the Enable/Disable RSR field, select Enable.

Go to Status > WAN/Cellular to check the RSR Test Result and confirm that traffic is being sent through the primary route. If the RSR Test Result field indicated that the Tracking Object Test has failed, validate the connectivity of the primary path. (The test result of Unknown indicates that the test has not yet run.)

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Dynamic Mobile Network Routing (DMNR)

Note: DMNR is supported only on the Verizon Wireless network.

DMNR provides direct communication between customer sites (for example, between remote subnets and the corporate data center) through a Mobile

Network Operator’s (MNO’s) private network (isolated from Internet traffic).

DMNR creates a tunnel between the home agent on the MNO’s private network and the AirLink gateway.

Primary Access Mode DMNR is supported on Ethernet LANs.

Head Office

MNO

Network

MNO’s Wireless

Private Network

DMNR tunnel

Home Agent

Enterprise to

Home Agent tunnel

AirLink DMNR client

Ethernet

Remote office

Switch

Ethernet

Subnet 1

Router

Up to 8 subnets supported

Ethernet

Subnet 2

Subnet 3

Retail environment

Figure 4-12: DMNR Configuration

Before configuring DMNR:

Go to LAN > DHCP/Addressing and ensure that the Host Connection Mode is set to All Hosts Use Private IPs (default).

Go to LAN > Host Port Routing and set the Primary Gateway field to Disable.

Go to VPN and disable any VPNs you have set up.

Once DMNR is configured, all traffic from the connected LANs goes through the DMNR tunnel.

Go to Security > Port Forwarding and set the DMZ Enabled field to Disable.

4118967

WAN/Cellular Configuration

Reboot the gateway.

Note: For the DMNR registration process to complete successfully, there must be a switch, router, or other device physically connected to the AirLink gateway’s Ethernet port.

To configure DMNR:

Go to WAN/Cellular > DMNR Configuration.

Rev 4 Jun.16

Figure 4-13: ACEmanager: WAN/Cellular >DMNR

Configure the fields as outlined in the following table.

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Field

Dynamic Mobile Network Routing

DMNR Enable

Description

Enables Dynamic Mobile Network Routing. Options are:

•

Enable

•

Disable (default) a

Note: Configure all the other parameters first and then set this field to Enable. When this field is set to Enable, the other fields in this window are read-only.

Home Address

Home Agent Address

N-MHAE-SPI

N-MHAE-KEY

Subnet 1 – 8

Enter a home address for the AirLink gateway. This address is used to distinguish the

AirLink gateway used for DMNR. You can enter any IP address for the Home Address, but if you are using more than one AirLink gateway for DMNR, each must have a different home address. Suggested value is 1.2.3.4. This field cannot be left blank.

IP address of the Home Agent (available from your Mobile Network Operator)

NEMO Authentication Extension Security Parameter Index (available from your Mobile

Network Operator)

NEMO Authentication Extension Key (available from your Mobile Network Operator)

Enter the IP addresses for the subnets you want to include in the DMNR network. You can configure up to 8 subnets.

0.0.0.0 indicates that the subnet is not configured.

Note: If you want to remove a subnet from the DMNR configuration, replace the IP address with 0.0.0.0 rather than deleting it.

Subnet 1 – 8 NetMask

Enter the Subnet Masks for the subnets you want to include in the DMNR network.

0.0.0.0 indicates that the subnet mask is not configured.

Note: If you want to remove a subnet mask from the DMNR configuration, replace the IP address with 0.0.0.0 rather than deleting it.

a. If you disable DMNR when the DMNR tunnel is up, no disconnect message is sent, resulting in a temporary mismatch between the reachability of the (NEMO) subnets on the gateway and the Home Agent.

82 4118967

WAN/Cellular Configuration

Click the + beside Foreign Agent and Reverse Tunnelling Agent.

Configure the Foreign Agent and Reverse Tunnelling Agent.

Field Description

Foreign Agent

Re-registration Timer

(seconds)

Retry Time Interval

(seconds)

Maximum Retry Count

The frequency with which the foreign agent re-registers its subnets

•

If the registration status is Down, the foreign agent re-registers its subnets when the time configured in this field expires.

•

If the registration status is Up, the frequency with which the foreign agent reregisters its subnets is equal to the Registration Response Lifetime minus the value configured in this field.

The Registration Response Lifetime is usually equal to the Registration Request

Lifetime (seconds)

. Once you have enabled DMNR, you can confirm the Registration Response Lifetime in ACEmanager.

Options are:

•

1–60 seconds (Default is 60 seconds.)

The interval (in seconds) between retries if the re-registration fails. Options are:

•

1–5 seconds (Default is 5 seconds.)

Maximum number of re-registration tries allowed. Options are:

•

0–5 (Default is 3.)

Registration Request

Lifetime (seconds)

Reverse Tunnelling Agent

Enter the desired registration lease time (in seconds). Options are:

•

0–65534 seconds (Default is 65534.)

Maximum Transmission

Unit - MTU (bytes)

Use this field to set the tunnel MTU for packets sent over the DMNR/GRE tunnel. Note that the tunnel adds 24 bytes to each packet so the tunnel MTU should be set at least 24 bytes lower than the Mobile Network MTU in order to avoid packet fragmentation.

Options are:

•

576–1500 (Default is 1476.)

Maximum Segment Size

- MSS (bytes)

Use this field to set the TCP maximum segment size for the packets (in bytes). Options are:

•

68–1436 (Default is 1436.)

Force Fragmentation

Allows you to override the “Do not fragment” bit in the incoming packet header and send large packets through the DMNR tunnel

Options are:

•

Enable—The “Do not fragment” bit in incoming packet header is cleared. This setting is useful if you need to send large packets or you do not know the MTU of all the routers in the network path.

•

Disable — The “Do not fragment” bit in the incoming packet header is respected. If the bit is set, packets larger than the MTU are dropped. If the DF bit is clear, packets larger than the MTU are fragmented and sent. (Default)

In the DMNR Enable field, select Enable.

Once DMNR is enabled, the fields are read-only. If you want to change any of the field entries, set the DMNR Enable field to Disable, make the required change, and then set the field to Enable.

Rev 4 Jun.16

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Figure 4-14: ACEmanager: WAN/Cellular > DMNR (enabled)

4118967

WAN/Cellular Configuration

Once DMNR is enabled, additional status fields appear, as described in the following table.

Field Description

Dynamic Mobile Network Routing

Subnet 1 – 8 Accepted

Confirms that the subnet configuration is accepted. Options displayed are:

•

Yes—The subnet is configured and accepted.

•

No—The subnet is not configured or not accepted.

Foreign Agent

Registration Status

Registration Response

Lifetime (seconds)

Foreign agent registration status

Options displayed are:

•

Pass—A response has been received form the Home Agent

•

Fail—No response from the Home Agent

•

Unknown—Initial state

Shows the length of the current lease time (in seconds).

Total RRQ sent

Total RRP received

Number of Registration Requests sent

Number of Registration Responses received

Reverse Tunnelling Agent

Reverse Tunnelling

Agent Status

DMNR tunnel status

This field only appears when DMNR is enabled. Options displayed are:

•

Up—DMNR tunnel is up.

•

Down—DMNR tunnel is down.

Force Fragmentation

Status of the Force Fragmentation field

•

Enabled

•

Disabled

For more information, see

Force Fragmentation on page 83.

TX packets

RX packets

Number of packets transmitted

The counter is reset when:

•

DMNR is disabled.

•

When the DMNR tunnel ( Reverse Tunnelling Agent Status ) is down.

Number of packets received

The counter is reset when:

•

DMNR is disabled.

•

When the DMNR tunnel ( Reverse Tunnelling Agent Status ) is down.

Rev 4 Jun.16

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

86 4118967

Rev 4 Jun.16

5: LAN Configuration

You can use the AirLink gateway to route data between one or more connected devices and the Internet via the mobile network. The

AirLink gateway has two modes you can use for configuring a LAN—

Private Mode and Public Mode.

Private and Public Mode

Private mode

Private Mode and Public Mode are Sierra Wireless terms. In Private

Mode, the router or laptop connected to the AirLink gateway has a

LAN IP address. In Public Mode the AirLink gateway passes the WAN

IP address to the router or laptop.

Public mode

Internet Internet

WAN IP address

AirLink gateway

WAN IP address LAN IP address

Router or laptop

Figure 5-1: Private vs. Public Mode

Router or laptop

Private Mode

Private Mode uses Network Address Translation (NAT) to enable the non-routable device to access the Internet. Data from the connected devices is passed through the AirLink gateway. By default, the first connected Ethernet or USBnet host is the DMZ host.

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Public Mode

Public Mode is similar to IP pass-through. When Public Mode is enabled, by default the Public Mode host becomes the DMZ host. Public Mode is required when the connected device needs a routable IP address and has no other connection to obtain it.

Tip:

When using Public Mode, Sierra Wireless recommends connecting the AirLink gateway directly to the computer or other end device. Using a hub or switch may prevent the AirLink gateway from updating the IP address of the end device when an IP address is received from the mobile network.

Port Use

Applications running on a LAN client such as a router or laptop must use different ports from those used by ALEOS features on the AirLink gateway. For a list of

inbound ports used by ALEOS, see Inbound Ports Used by ALEOS on page 431.

DHCP/Addressing

This page governs the DHCP and addressing for all interfaces.

The LAN Address Summary is a display of the IP addresses assigned to interfaces on their respective configuration pages. To change the addressing for the Ethernet interface, go to the Ethernet side menu. To change the addressing for the USBnet interface, go to the USB side menu.

Note: If the gateway has not been reset since configuration changes were made, the current configuration in use may be different.

88 4118967

LAN Configuration

Rev 4 Jun.16

Figure 5-2: ACEmanager: LAN > DHCP/Addressing

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Field

General

Host Connection

Mode

Description

Sets the Host Interface to use the Public IP address granted by the mobile network or private IP addresses. All host interfaces which are not using the public IP address use private IP addresses. The options are:

•

Ethernet Uses Public IP*

•

All Hosts Use Private IP—(default)

•

USB Uses Public IP*

•

Serial DUN Uses Public IP*

•

First Host gets Public IP*

If you select this option, you do not have to specify the type of connection that uses the Public IP address. The first device to connect uses the Public IP address, regardless of whether it has a USB or Ethernet connection.

* Until the gateway is able to obtain a mobile network connection, it provides private IP addresses in response to DHCP requests.

For more information on Private and Public mode, see

Private and Public Mode on page 87.

Note: If you plan on using

Dynamic Mobile Network Routing (DMNR)

, select Ethernet

Uses Public IP in this field.

Note: The connected computer receives the DHCP address from ALEOS and it also provides a static route (192.168.13.31 by default) that allows you to access ACEmanager from a connected device.

Public Mode Subnet

Mask

This field appears when Ethernet, USB, or Serial (RS232) Uses Public IP is selected in the

Host Connection Mode field. Public Mode subnet mask indicates the range of Public Mode host IP addresses. Options are:

•

255.255.255.0 (24-bit) (default)

•

255.255.255.255 (32-bit)

Choose the option that matches the subnet mask received from the mobile network.

Lease Timer

(seconds)

The amount of time the DHCP client is given for the use of the IP address (in seconds)

Options are:

•

120–4294967295—Number of seconds the IP address is leased for.

If you want to set the value to “infinity”, enter 4294967295 (equivalent to 136 years).

The actual maximum value depends on the maximum supported by your DHCP client.

The default lease time is 3600 seconds (1 hour).

LAN Address Summary

Displays the interfaces which have been enabled. By default, only the Ethernet and USBNET Interfaces are enabled.

This table also includes VLAN if configured.

Interface

Device IP

The physical interface port or VLAN ID

The IP address of the AirLink gateway for the specified interface port. By default, this is set to 192.168.13.31 for Ethernet, and 192.168.14.31 for USB/net.

90 4118967

LAN Configuration

Field

Subnet Mask

Access WAN

Description

Subnet mask indicates the range of device IP addresses that can be reached directly.

Changing this limits or expands the number of clients that can connect to the AirLink gateway. The default of 255.255.255.0 means that 253 clients can connect to the AirLink gateway. Uses 192.168.13. as the first three octets of the IP address if the gateway IP is

192.168.13.31.

Appears if the interface is configured to allow connected device(s) access to the Internet

Note: Internet access cannot be disabled for Ethernet hosts.

DHCP Mode

Indicates whether or not the interface has a DHCP server enabled to provide dynamically allocated IP addresses provided to connected devices

Note: The DHCP server can only be disabled for Ethernet and VLAN.

Starting IP

Ending IP

Ethernet DHCP pool starting IP address (DHCP low address)

The ending IP for the interface (DHCP high address). If the starting and ending IP are the same, there is a single address in the pool and only one connected device receives an IP address from the DHCP server for that interface. Some interfaces, such as USB, can only have a single device connection. For others, statically assigned IP addresses in the same subnet, but outside of the DHCP pool, can still connect and use the gateway in the same way as a DHCP connected device.

Tip:

If you are using Private Mode for all hosts (*HOSTPRIVMODE=1), make sure that device IP, Starting IP, and Ending

IP are on the same subnet defined by the DHCP network mask. If the subnet mask is 255.255.255.0, it is safe to use

192.168.x.y for each as long as the x is the same number (0 in the example screen shot above) and the y is different (1 and 2 in the example) and between 1 and 254.

Rev 4 Jun.16

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Field Description

DHCP Reservation List

Reservation List

Use this list to reserve IP addresses for up to 5 connected devices, based on their MAC addresses. This feature is useful if you have multiple connected devices behind the AirLink gateway where you need to use DHCP addressing and also need to assign a specific IP addresses to some devices.

To reserve an IP address:

Click Add More.

Complete the

MAC Address and IP Address

fields.

The device does not need to be connected when you complete these fields.

Click Apply.

To delete a reserved IP address, click the X beside the reserved IP address.

Note:

•

A reserved IP address must be from a private subnet configured for the applicable interface. For example, 192.168.13.10 for an Ethernet connected device.

•

When Host Connection Mode is set to Public for a particular interface, the DHCP reservations for that interface are overridden. Any device connected to the specified interface (and port for Ethernet) receives the public IP. Any other device connected to the same interface type does not receive any IP from DHCP.

•

The reservation list supports Ethernet hosts.

MAC Address

IP Address

Enter the MAC address of the device you want to reserve an IP address for.

Enter the IP address you want to reserve for the device.

DHCP Options

Enables IT Administrators to configure up to 10 DHCP options, allowing you to push DHCP options to connected devices.

Interface

Select the interface to use:

•

All (default)

•

Ethernet

•

USB

Note: VLAN hosts only receive the DHCP options when the Interface is set to All.

Option Code

Option Value

Choose from the options in the drop-down menu. For a list of supported Option Codes, see

Table 5-1

. For additional information on the option codes, refer to the Internet Engineering

Task Force (IETF) memorandum on Internet Protocols and Standards, RFC-2131.

The format for the option value depends on the

Option Code selected, as formats must

conform with RFC 2132. For a list of accepted formats for each of the supported DHCP

Option Codes, see Table 5-1 .

Use a comma to separate multiple values.

DHCP Vendor Specific Options

Enables IT Administrators to configure up to 5 vendor-specific options

Vendor Class

Enter the vendor class

92 4118967

LAN Configuration

Field Description

Vendor Option Code

Enter the vendor option code. Possible entries are:

•

0–255

Vendor Option Length

This field allows you to specify the DHCP vendor specific option length in order to ensure that the DHCP datagram is correctly formatted for the DHCP client. Options are:

•

Undefined— Use this setting for IP addresses and strings (default)

•

1 byte—Use for decimal values of 255 or less

•

2 bytes—Use for decimal values between 256 and 65535

•

4 bytes—Use for decimal values greater than 65535

Note: If the size used for the data is not correct, the option is ignored by the client.

Vendor Option Value

Enter the vendor option value in one of the following formats:

•

Dotted-quad IPv4 address

•

Decimal number

•

Colon-separated hex digits

•

Text string

Use a comma to separate multiple values.

Table 5-1: Supported DHCP Options

DHCP Option

002 Time Offset

003 Router

007 Log Server

009 LPR Server

013 Boot File Size

015 Domain Name

016 Swap Server

017 Root Path

018 Extension Path

019 IP Forward Enable/Disable

020 Non-Local Source Routing

021 Policy Filter

022 Max Datagram Reassembly Size

023 IP TTL

Rev 4 Jun.16

Type of entry

32-bit unsigned integer

1 or more IP addresses

16-bit unsigned integer

Fully Qualified Domain Name

(FQDN)

1 or more IP addresses

ASCII string

Single octet Boolean

1 or more pairs of IP addresses or

IP address/mask pairs

16-bit unsigned integer

8-bit unsigned integer

Accepted values

(if applicable)

-43200–43200 a

1–65535

0 (Disable) or 1 (Enable)

576–65535

1–255

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Table 5-1: Supported DHCP Options

DHCP Option Type of entry

026 Interface MTU

16-bit unsigned integer

027 All Subnets Are Local

031 Perform Router Discovery

032 Router Solicitation Address

034 Trailer Encapsulation

035 ARP Timeout

036 Ethernet Encapsulation

037 TCP TTL

038 TCP Keepalive

Single octet Boolean

Single IP address

Single octet Boolean

32-bit unsigned integer

Single octet Boolean

8-bit unsigned integer

32-bit unsigned integer

040 NIS Domain

041 NIS Server

042 NTP Server

044 NetBIOS Name Server

ASCII string

Single IP address

1 or more IP addresses

045 NetBIOS Datagram Distribution Server

1 or more IP addresses

046 NetBIOS Node Type

8-bit unsigned integer

047 NetBIOS Scope

048 X Windows System Font Server

ASCII string

1 or more IP addresses

049 X Windows System Display Manager

064 NIS+ Domain

065 NIS+ Server

066 TFTP Server

1 or more IP addresses

Domain name

Single IP address

ASCII string or IP address

067 Bootfile Name

068 Mobile IP Home

069 SMTP Server

070 POP3 Server

ASCII string

1 or more IP addresses

071 NNTP Server

074 IRC Server

1 or more IP addresses

1 or more IP addresses a. The time offset is entered as seconds. See

Table 5-2

for a list of hour/second conversions.

Accepted values

(if applicable)

68–65535 (Default is

1500.)

0 (Disable) or 1 (Enable)

6–65535

0 (Disable) or 1 (Enable)

1–255

0–65535

Domain name

1, 2, 4, or 8

Name, domain name, or

IP address

Name

94 4118967

LAN Configuration

Table 5-2: Time Offset Hour / Second conversions

Hour Seconds Hour

25200

28800

32400

36000

39600

43200

3600

7200

10800

14400

18000

21600

-5

-6

-7

-8

-1

-2

-3

-4

-9

-10

-11

-12

-3600

-7200

-10800

-14400

-18000

-21600

-25200

-28800

-32400

-36000

-39600

-43200

Seconds

Internal DHCP Server

DHCP (Dynamic Host Configuration Protocol) has become a primary component of today’s network environments. DHCP allows one server to automatically and dynamically allocate network IP addresses and other network related settings

(such as subnet masks, routers, etc.) to each computer or device without the need to set up each specifically or keep track of what addresses have already been used.

In a default configuration, the AirLink gateway acts as a DHCP host to any device connected to its ports. This DHCP host provides that device with an IP address that can be used to communicate on the Internet.

Address Assignment in Public Mode

When the AirLink gateway registers on the mobile network, it is assigned an

IP address from the carrier, e.g., 10.1.2.0.

When using a specific interface, the AirLink gateway acts as a DHCP server unless disabled. When the Host Connection Mode is Ethernet Uses Public IP, and the AirLink gateway receives a DHCP request from an Ethernet device connected to its ports, it hands off the assigned address to the device and sets up the default gateway address as 10.1.2.1. If the fourth octet value is already a 1, it assigns 10.1.2.2 as the router address.

Rev 4 Jun.16

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Note: The primary gateway to the mobile network, for any connected device, is enabled by default.

The AirLink gateway also sends a /24 netmask (255.255.255.0 by default) and sets up a static route which maps 192.168.13.31 (or the address configured with *HOSTPEERIP if it is changed) to 10.1.2.1 (or 10.1.2.2 if that was what the gateway address was given as).

Tip:

When PPPoE is used with the AirLink gateway, the DHCP server needs to be disabled. A tunnel is set up connecting a device (such as your computer or a router) with the AirLink gateway. The device then uses the MAC address of the AirLink gateway to send all outgoing packets.

Ethernet

The AirLink gateway is equipped with an Ethernet port that can be enabled or disabled as needed. When the port is disabled, the connected device cannot connect via Ethernet, and ARP queries do not receive responses on the port.

Figure 5-3: ACEmanager: LAN > Ethernet

4118967

LAN Configuration

Field

General

Ethernet Port

Description

Device IP

Starting IP

Enabled or Disabled

Note: When the port is disabled, the device ignores any physical connection to the

Ethernet port.

The Ethernet IP address of the AirLink gateway. By default this is set to 192.168.13.31.

Ethernet DHCP pool starting IP address

Default is 192.168.13.100.

Note: If only one computer or device is connected directly to the Ethernet port, this is the

IP address it is assigned.

Ending IP

DHCP network mask

DHCP Mode

The ending IP address for the Ethernet interface DHCP pool

Default is 192.168.13.150.

The Netmask given to any Ethernet DHCP client

Default is 255.255.255.0.

Determines how DHCP operates on the Ethernet interface

Options are:

•

Server—The AirLink gateway acts as a DHCP server for all Ethernet connections.

•

Disable—The AirLink gateway acts as neither a DHCP server or client. All devices connected to the AirLink gateway must have a static LAN IP or use PPPoE.

•

Auto—When the gateway is powered on or reboots, it attempts to determine if a

DHCP server is present on the Ethernet network. If a DHCP server is found, the gateway obtains an IP address and uses Ethernet for communication with AirLink

Management Service (ALMS). If a DHCP server is not found, the gateway becomes a DHCP server. (default)

Most of the time you can leave this field set to the default value.

Advanced

Link Radio coverage to

Interface

Radio Link Delay

(seconds)

This disables the specified port when there is no cellular coverage. Options are:

•

Disable (default)

•

Ethernet

•

USB

The delay in seconds before the selected interface goes down when there is no cellular coverage

Rev 4 Jun.16

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Field

Interface Disabled

Duration

Turn Off NAT

Ephemeral Port

Description

Sets the period of time (in seconds) that the LAN interface is disabled when linking a LAN port to radio coverage. Either the Ethernet or the USB LAN port can be linked to the radio coverage, but not at the same time. Options are:

•

Interface Disabled when Radio is disconnected (default)

•

5 Sec

•

10 Sec

•

15 Sec

•

20 Sec

•

25 Sec

•

30 Sec

When enabled, ALEOS routes outbound packets from connected devices without performing NAT on them. For example, when a connected device that has an IP address of 192.168.13.100 sends data to a remote destination, the outbound packets have a source IP of 192.168.13.100.

In most cases, it is best to leave this field at the default setting (Disabled), as most mobile network operators do not support this functionality.

Enable or Disable the Ephemeral Port feature

•

Disable—The source port in packets the AirLink gateway receives from a connected device and then sends out is not changed. The source port assigned to the packet when it was created in the customer’s connected device is used. (default)

•

Enable—The AirLink gateway changes the source port on all outgoing NATed UDP packets, using the range configured in the Starting Ephemeral Port field.

98 4118967

LAN Configuration

Field Description

Starting Ephemeral Port

This field appears only when the Ephemeral Port field is set to Enable. It allows you to set the starting port range used by a LAN device as the source port for over-the-air (OTA) destinations using NAT.

Note: This field is intended for advanced users only. In most cases, use the default value.

The NAT for the LAN device uses a range of 1000 ports as source ports for OTA destinations beginning with the configured Ephemeral port. Options are:

•

1024 (default)–64535

If you have a network with multiple LAN devices that are sending data to the same server and the server is not receiving data from one (or more) of the devices, it may be because the Mobile Network Operator has a WAN firewall that is blocking the ports used by the

NAT for over-the-air (OTA) destinations. This field enables you to avoid the blocked ports by changing the source port range used to send the data. For example, some users have found that changing the starting port to 42000 has resolved the issue.

Note: The ephemeral port setting does not affect any outbound traffic initiated by the device such as GPS reports, Events Reporting, Device Initiated ALMS connection, etc.

Ethernet 1 Link Setting

Configures the Ethernet port speed and duplex setting

Most of the time you can leave the default setting and the device you are connecting automatically negotiates the speed and duplex setting with the AirLink gateway.

However, if the connected device has a fixed setting, use this field to change the AirLink gateway setting to match that of the connected device.

Note: If you select 100 Mb Full Duplex or 10 Mb Full Duplex for the gateway, ensure that the same speed is selected on the connected device.

The options are:

•

Auto—The RV50 auto-negotiates with the connected device to use the fastest speed possible—10 Mb, 100 Mb, or 1000 Mb (default). For best results, ensure that the connected device is also set to auto-negotiation.

If your highest priority is power saving, select one of the 100 Mb or 10 Mb settings.

•

100 Mb Full Duplex

•

100 Mb Half Duplex

•

10 Mb Full Duplex

•

10 Mb Half Duplex

You can view the current speed and duplex setting on the Status > LAN page. See

page 46

USB

The AirLink gateway is equipped with a USB port that increases the methods by which you can send and receive data from a connected computer. You can set up the USB port to work as either a virtual Ethernet port or a virtual serial port, or

Rev 4 Jun.16

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50 you can disable it to prevent access by USB. You may need to install a USB driver to use these modes. For more information, see

Installing the USB Drivers on page 102.

By default, the port is set to work as a virtual Ethernet port.

Note: Sierra Wireless recommends that you use a USB 2.0 cable with your AirLink gateway and connect directly to your computer for best throughput.

To change the USB port to allow virtual serial port communication:

In ACEmanager, go to LAN > USB, and choose USB Serial as the USB

Device Mode.

To disable the USB port, select Disable from the same menu.

Figure 5-4: ACEmanager: LAN > USB

100 4118967

LAN Configuration

Field

General

USB Device Mode

Description

The USB mode on gateway startup

•

USB Serial—USB port acts as a virtual Serial port.

•

USBNET—USB port acts as a virtual Ethernet port. (default)

•

Disabled—USB port is disabled.

You can also configure this parameter using the AT Command *USBDEVICE. See

*USBDEVICE on page 378.

Note: A reboot is required to activate the USB mode change.

Note: If you want to stream GPS data to the USB port (

Local/Streaming on page 222), set

this field to USB Serial.

Device USB IP

Host USB IP

USB Network Mask

USB Serial Echo

USBNET Host WAN

Connectivity

The USBNET IP address of the AirLink gateway. By default this is set to 192.168.14.31.

The IP for the computer or device connected to the USB port

Use this field to configure a subnet mask for USBNET

Default is 255.255.255.0

The AT command echo mode when the USB is configured as a virtual serial port

Options:

•

Enable—Echoes commands to the computer (so you can see what you type) (default)

•

Disable—Does not echoes commands to the computer (you cannot see what you type)

Controls access to the WAN over the USB port

Options are:

•

Enable—USB can be used to access the WAN (default)

•

Disable—Access to the WAN over USB is blocked.

Advanced

Link Radio Coverage to Interface

Disables the specified port when there is no cellular coverage. Options are:

•

Disable (default)

•

Ethernet

•

USB

Rev 4 Jun.16

101

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Field

Radio Link Delay

(seconds)

Interface Disabled

Duration

Description

The delay in seconds before the selected interface goes down when there is no cellular coverage

Valid range is 0–65535. Default is 10.

•

Interface Disabled when Radio Disabled (default)

•

5 seconds

•

10 seconds

•

15 seconds

•

20 seconds

•

25 seconds

•

30 seconds

Installing the USB Drivers

A USB driver is required if you want to use the USB port on the gateway as a virtual serial port (USB Serial). If you want to use the USB port as a virtual

Ethernet port (USBnet), a driver is not required as the default Microsoft Windows

7 and Windows 8 drivers are used.

To install the USB Serial drivers for Windows 7 and Windows 8:

Go to source.sierrawireless.com

and download the USB Serial Driver One-

Click Tool.

Double-click the downloaded file (AirLink_Serial_<version number>.exe).

As the drivers installs, a progress box appears in the lower right-hand corner of the monitor.

Figure 5-5: USB Serial One-Click Tool progress window

In ACEmanager, go to LAN > Ethernet and set the USB Device Mode field to

USB Serial.

Connect a gateway to the computer using a USB cable.

The driver installation completes and a window opens indicating the Serial

Port number.

Figure 5-6: USB Serial Driver Installation Complete

102 4118967

LAN Configuration

At any time, you can open Device Manager to check the Serial Port number.

Rev 4 Jun.16

Figure 5-7: Device Manager

Note: USB serial and USBnet drivers available at

source.sierrawireless.com

also work with Linux CDC-ACM drivers.

Note: The COM port number assigned by driver installation is the next port that is available.The port number might vary depending on the number of devices connected

(using serial or virtual serial).

Once the driver is installed, you can use the USB port just like a standard serial port.

Host Port Routing

Host port routing enables the AirLink gateway to handle network communication for up to two non-NATed networks behind the gateway or router connected to the

AirLink gateway. The following illustration shows a typical network configuration.

Note: The AirLink gateway does not handle addressing for devices behind the router or gateway.

103

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Internet

AirLink gateway

Switch

192.168.13.20

Router

Gateway

192.168.10.0/24

Host Network 2

Figure 5-8: Host Port Routing Network Configuration

192.168.20.0/24

Host Network 3

104

Figure 5-9: ACEmanager: LAN > Host Port Routing

4118967

LAN Configuration

Field

Primary Gateway

Host Network 2 and

Host Network 3

Host Network Subnet

Mask 2 and Host

Network Subnet Mask 3

Host Network 2 Route and Host Network 3

Route

Description

When enabled, your AirLink gateway is the primary gateway for connected LANs and responds to Address Resolution Protocol (ARP) requests to resolve WAN addresses for devices on the connected LANs. Default is Enabled.

Enter the IP address for Host Network 2 and 3. These are LAN networks connected to the AirLink gateway behind a router or gateway. They do not have the same IP range as the AirLink gateway LAN network. For example, 192.168.10.0.

The subnet for the applicable network. For example, 255.255.255.0, which would with the setting above define a secondary network of 192.168.10.0/24.

Host Network 2

Gateway and Host

Network 3 Gateway

Indicates whether a router or gateway is being used for the host network. Options are:

•

Ethernet— Select this option if the network uses a router that acts as an ARP proxy for addresses on its subnet.

•

Gateway—Select this option if the network uses a device that does not handle ARP requests. When Gateway is selected, ALEOS handles ARP requests for the connected LAN devices. Any traffic destined for a host on the network behind a gateway is routed, by the device, through the gateway IP.

•

If you selected Gateway in the Host Network Route field, enter the IP address for the gateway.

•

If you selected Ethernet in the Host Network Route field, leave this field as 0.0.0.0.

Global DNS

When the mobile network grants the IP address to the device, it includes the IP addresses of its DNS servers. Global DNS allows you to override the Mobile

Network Operator’s DNS settings for all connected devices. This is useful when the connected devices need to use a private network.

Note: If there are no alternate DNS servers defined, the default is the WAN network DNS server.

Rev 4 Jun.16

105

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Figure 5-10: ACEmanager: LAN > Global DNS

Field

Primary DNS

Secondary DNS

DNS Proxy

DNS Override

106

Description

Primary Mobile Network Operator’s DNS IP Address. This and the secondary DNS are generally granted by the mobile network along with the Network IP.

Secondary Mobile Network Operator’s DNS IP Address

Determines whether or not the AirLink gateway is used as a DNS proxy server.

Note: Using the AirLink gateway as a proxy DNS server can help reduce mobile network data use.

Options are:

•

Enable (default) —All connected DHCP clients (PPP, PPPoE, USBNET, and Ethernet) send their DNS IP address resolution requests to the AirLink gateway. The AirLink gateway performs DNS lookups on behalf of the DHCP client.

•

If the AirLink gateway is able to resolve the request, it sends a response to the

DHCP client.

•

If the AirLink gateway does not have the necessary information to resolve the request, it sends the request to the DNS server configured in the DNS Override field. When the AirLink gateway receives a response, it forwards it to the DHCP client and saves the information so that it can resolve the same request in the future.

•

Disable—All connected DHCP clients send their DNS IP address resolution requests to the DNS server received from the mobile network or the alternate server specified by DNS Override, if enabled. The AirLink gateway is not used as a DNS server.

Overrides the Mobile Network Operator’s DNS address with the DNS server configured in the Alternate Primary DNS and Alternate Secondary DNS fields.

Options are:

•

Disable (default)—Mobile Network Operator’s DNS server is used

•

Enable—Alternate DNS server is used

4118967

LAN Configuration

Field

Alternate Primary

DNS

Alternate Secondary

DNS

Alternate DNS Port

Description

Configure the primary DNS server to use instead of the Mobile Network Operator’s DNS server

Configure the secondary DNS server to use instead of the Mobile Network Operator’s DNS server

If you want to specify the port on the connected device that the AirLink gateway sends IP address resolution responses to:

Ensure that the DNS Override

field is set to Enable.

Enter the desired port number in this field.

Click Apply.

When this field is set to 53 (default) or 0, packets are sent to port 53, the standard DNS port.

PPPOE

PPPoE (Point-to-Point Protocol over Ethernet) allows a point-to-point connection while using Ethernet. Just like the dial up protocol on which it is based, PPPoE can use traditional user name and password authentication to establish a direct connection between two Ethernet devices on a network (e.g., your AirLink gateway and your computer or router).

examples for PPPoE with your AirLink gateway:

•

Backup connectivity solution for your network

•

Individualized Internet connection on a LAN

•

Password restricted Internet connection

Only one computer, router, or other network device at a time can connect to the

AirLink gateway using PPPoE. If you are using the AirLink gateway connected to a router as a back up Internet connection for your network, you should configure the router to use the PPPoE connection and not the individual computers.

Note: To configure a PPPoE connection on some operating systems, you need administrator privileges to the computer you are configuring or access granted by an administrator on the network to add/remove devices to your computer.

Rev 4 Jun.16

107

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Figure 5-11: ACEmanager: LAN > PPPoE

Field

Host Authentication

Mode

Host User ID

Host Password

Description

Host Authentication Mode: Use PAP or CHAP to request the user login and password during PPP or CHAP negotiation on the host connection. The username and password set in *HOSTUID and *HOSTPW is used.

•

NONE (default)

•

PAP and CHAP

•

CHAP

User ID for authentication (up to 64 bytes)

Password for authentication

Configure the AirLink gateway to Support

PPPoE

Note: You must disable the DHCP server for PPPoE to work.

To configure an AirLink gateway to support PPPoE:

In ACEmanager, go to LAN > Ethernet.

Under General, in the DHCP Server Mode field, select Disable.

Note: PPPoE authentication is optional. If you use PPPoE authentication, no other tethered LAN connection will have network access, regardless of whether or not the

PPPoE host is connected. If you are using non-authenticated PPPoE, other tethered LAN connections will have network access until a PPPoE host is connected.

108 4118967

LAN Configuration

If you want to use authenticated PPPoE:

Go to LAN > PPPoE, and in the Host Authentication Mode field, select

PAP and CHAP.

b. In the Host User ID, enter a user ID for the PPPoE connection.

In the Host Password field, enter a password for the PPPoE to connection.

Click Apply.

Reboot the gateway.

Tip:

If you leave Host User ID and Host Password blank, any computer or device can connect to the AirLink gateway using PPPoE.

Note: ACEmanager shows the existing value for the PPPoE password as stars (****).

Optional: Configure the Device Name

In ACEmanager, go to Services > Dynamic DNS.

In the Service field, select IP Manager.

Under Dynamic IP, enter a name in the Device Name field, such as AirLink gateway or the ESN. The name can be up to 20 characters long.

The name you choose for Device Name does not affect the connection, but may need to be configured in PPPoE settings for the router, device, or computer you connect to your AirLink gateway.

Configuring a PPPoE Connection in Windows 7

In Windows 7, go to Start > Control Panel.

Rev 4 Jun.16

Figure 5-12: Windows 7: Control Panel

109

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Select Network and Internet.

Figure 5-13: Windows 7: Control Panel > Network and Internet

Select Network and Sharing Center.

110

Figure 5-14: Windows 7: Control Panel > Network and Sharing Center

In the middle of the page, under Change your networking settlings, select Set up a new connection or network.

4118967

LAN Configuration

Figure 5-15: Set Up an Connection or Network

Select Connect to the Internet and click Next.

Rev 4 Jun.16

Select Broadband (PPPoE).

111

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

112

If you are using authenticated PPPoE, enter the User name and Password you configured in ACEmanager.

If desired, change the Connection name to something such as PPPoE that clearly identifies the connection.

Click Connect.

For subsequent connections, you can click the network icon in the Task bar ( ) and select the PPPoE connection.

VLAN

ALEOS supports up to three Virtual Local Area Networks (VLANs) on its Ethernet port. VLANs are logical groupings of network devices that share the same broadcast domain. All devices on the same VLAN can ping each other without routing. ALEOS does not support routing between VLANs.

Note: The VLANs must also be configured on the switch.

4118967

LAN Configuration

WAN

VLAN Switch

AirLink gateway

Connected device on VLAN 1

Connected device

on VLAN 1

Connected device on VLAN 2

Figure 5-16: VLAN network configuration

Connected device on VLAN 1

Connected device on VLAN 2

Field

Interface

VLAN ID

Device IP

Subnet Mask

Figure 5-17: ACEmanager: LAN > VLAN

Description

Displays the three VLANs you can configure

VLAN ID

•

0—VLAN is disabled (default)

•

1–4094—Valid range for VLAN ID

The IP address of the AirLink gateway for that VLAN interface

The subnet mask indicates the range of host IP addresses that can be reached directly.

Changing the subnet mask limits or expands the number of devices that can connect to the

AirLink gateway.

Rev 4 Jun.16

113

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Field

Access WAN

DHCP Server Mode

Starting IP

Ending IP

Description

Choose whether or not devices on the configured VLAN have access to the WAN.

•

Yes

•

Choose whether or not the AirLink gateway acts as a DHCP server

Options are:

•

Enable—AirLink gateway acts as the DHCP server

•

Disable (default)

VLAN interface DHCP pool starting IP address

VLAN interface DHCP pool ending IP address

VRRP

VRRP (Virtual Router Redundancy Protocol) enables you to configure a backup

WAN connection to be used if the primary connection fails. You can configure

VRRP on the AirLink gateway’s Ethernet port or for VLANs.

You configure a VRRP Master and VRRP Backup device(s) and set their priorities. The device with the highest priority (normally the VRRP Master) becomes the primary route for the data connection.

The VRRP Master and Backups share a common virtual IP.

For information on configuring VLANs, see

VLAN on page 112.

One common scenario is to use a 3rd party router for the primary connection and the AirLink gateway, either with or without VLANs, for the backup connection.

WAN

Backup WAN connection

Primary WAN connection

Router (VRRP Master)

Switch

AirLink gateway

(VRRP Backup)

Connected device

Connected device Connected device Connected device Connected device

Figure 5-18: VRRP Network Configuration without VLANs

Connected device

114 4118967

Rev 4 Jun.16

LAN Configuration

WAN

Backup WAN connection

Primary WAN connection

Router (VRRP Master)

VLAN Switch

AirLink gateway

(VRRP Backup)

Connected device on VLAN 1

Connected device

on VLAN 1

Connected device on VLAN 2

Figure 5-19: VRRP Network Configuration with VLANs

Connected device on VLAN 1

Connected device on VLAN 2

Figure 5-20: ACEmanager: LAN > VRRP (no VLANs)

115

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

116

Figure 5-21: ACEmanager: LAN > VRRP (VLANs)

You can also set up VRRP using two AirLink gateways —one configured as the

VRRP Master and the other as the VRRP Backup. The Backup AirLink gateway provides an alternate route when the Master AirLink gateway loses coverage.

For example, if you have cellular accounts with two different Mobile Network

Operators (MNOs) you might prefer to use MNO A’s connection, but to maintain continuity, you would like traffic to switch to MNO B if A’s network is down and switch back to A’s network once the connection is re-established.

WAN

Wireless connection on MNO A’s network (primary route for data)

Wireless connection on

MNO B’s network

(Backup route for data when the primary route is down)

AirLink gateway on MNO A’s network

(VRRP Master, with priority configured as 100, for example)

Switch

AirLink gateway on MNO B’s network

(VRRP Backup, with priority configured as 75, for example)

Connected device Connected device Connected device

Figure 5-22: VRRP Network Configuration using two AirLink gateways

4118967

LAN Configuration

Field Description

VRRP Enabled

Allows you to activate VRRP. Options are:

•

Enable

•

Disable (default)

VRRP — The VLAN ID, Group ID, and Virtual IP address must be the same on the VRRP Master and

VRRP Backup devices.

Interface

VLAN ID

Group ID

Priority

Virtual IP

Displays Ethernet port on AirLink gateway and the VLAN numbers

Displays the VLAN ID

This value is inherited from the LAN > VLAN screen. (See VLAN on page 112.)

•

0—VLAN is disabled

•

1– 4094—Valid range for VLAN ID

Enter the VRRP Group ID. Configure the VRRP Master (for example, the 3rd party router) and the VRRP Backup (for example the AirLink gateway) with the same Group ID.

Options are:

•

0–255 (Default is 0.)

Use this field to configure the priority for the AirLink gateway.

The device with the highest priority (typically a 3rd party router) provides the primary data traffic route. If the device loses its connection to the WAN, its priority number drops. If the device fails, then when the failure is detected, the next highest priority router becomes the active router.

The priority number configured on the VRRP Backup (typically the AirLink gateway) should be less than the initial priority number on the VRRP Master and greater than the value that the VRRP Master’s priority number would be if it drops as a result of losing its WAN connection.

For example, if the VRRP Master router has an initial priority number of 200 that drops to

80 if it loses its WAN connection, setting the AirLink gateway’s priority to 100 ensures that it becomes the primary route if the VRRP Master loses its WAN connection. When the 3rd party router re-establishes its connection, its priority returns to 200 and it once again becomes the primary route for data.

Options are:

•

1–255 (Default is 100.)

Configure the same virtual IP for the VRRP Backup (typically the AirLink gateway) and the

VRRP Master (typically a 3rd party router). The virtual IP must be unique within the VLAN subnet and cannot be within a pool of addresses assigned via DHCP.

Rev 4 Jun.16

117

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Field

Mode

Interval

Description

Indicates the initial mode for the AirLink gateway

Options are:

•

MASTER

•

BACKUP (default)

Note: Designating a device as “Master” in this field does not make it the primary route for data unless it is also given a higher priority number than the VRRP Backup device. See

Priority .

If the AirLink gateway is acting as VRRP Master, it advertises its Master status at the interval (in seconds) configured in this field. Options are:

•

1–65535 seconds (Default value is 1.)

Host Interface Watchdog

The Host Interface Watchdog provides a way for you to ensure that the LAN connection is alive. You can use this feature to monitor:

•

A host connected to the LAN via an Ethernet or USB connection

When the Host Interface Watchdog is enabled, ALEOS sends a ping to the connected device at configured intervals. You can disable Force Keepalive to only send a ping when there is no traffic on the LAN interface. (See

Force LAN

Keepalive on page 119.)

If there is no response to the ping, the LAN interface is reset.

Note: The network interface is automatically determined from the IP address and the LAN configuration.

After the interface comes back up, ALEOS sends another ping to the connected device. If there is still no response to this ping, the AirLink gateway reboots. After a reboot caused by the LAN Interface Watchdog, ALEOS waits an hour before attempting pings to prevent repeated frequent reboots.

Note: DUN (PPP) is not supported. If the IP address for the host is on a DUN network, the feature is disabled.

Note: The feature is not disabled when the interface uses Public Mode, but it cannot monitor the host interface unless the mobile network provides a static IP.

118 4118967

LAN Configuration

Figure 5-23: ACEmanager: LAN > Host Interface Watchdog

Field

LAN Keepalive IP address

LAN Keepalive

Interval (minutes)

Force LAN Keepalive

Description

Enter the IP address of the device to ping

If a device IP address is not configured, the Host Interface Watchdog is disabled.

The interval (in minutes) at which ALEOS pings the LAN-connected device

Options are: 1–1440

If this field is set to 0, the Host Interface Watchdog is disabled. (default)

To prevent the gateway from rebooting frequently when a connection is not available, if the gateway reboots as a result of a failed keepalive ping, it waits 60 minutes before sending another keepalive ping. Once the ping is successful, the gateway returns to the interval configured in this field.

•

Enabled (default) —The network interface statistics are not monitored and a ping is always sent at the interval configured in the Keepalive Interval field.

•

Disabled—The network interface statistics are monitored and connectivity is assumed when there is traffic received. A ping is only sent when there is no traffic for a period greater than the interval set in the Keepalive Interval field.

Rev 4 Jun.16

119

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

120 4118967

Rev 4 Jun.16

6: VPN Configuration

The AirLink gateway can act as a Virtual Private Network (VPN) device, providing enterprise VPN access to any device connected to the AirLink gateway even when a device has no VPN client capability on its own. The AirLink gateway supports three types of VPN: IPsec,

GRE, and SSL. The AirLink gateway can support up to five VPN tunnels at the same time.

Note: Dynamic Mobile Network Routing (DMNR) is not compatible with VPN tunnels. If you are using DMNR, disable all VPN tunnels.

Split Tunnel

The AirLink gateway supports Global settings with one encrypted tunnel and one open tunnel. A sample server subnet for a Global setting would be 172.16.1.0/24. Global settings VPNs should be set up with care, as a Global settings configuration with both an enterprise VPN and access to the public Internet can inadvertently expose company resources.

Figure 6-1: ACEmanager: VPN > Split Tunnel

121

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

122

Field

Incoming Out of Band

Outgoing Management

Out of Band

Outgoing Host Out of

Band

Description

Controls incoming public Internet traffic

Options are:

•

Blocked—Incoming public Internet traffic is blocked. Only traffic through the VPN tunnel is allowed. (default)

•

Allowed—Incoming public Internet traffic is allowed.

Controls outgoing traffic from the AirLink gateway

•

Blocked—Outgoing traffic from the AirLink gateway to the public

Internet is blocked. Only traffic through the VPN tunnel is allowed.

•

Allowed—Outgoing traffic from the AirLink gateway to the public

Internet is allowed. (default)

Controls of outgoing Host out of band traffic.

Options are:

•

Blocked—Public Internet traffic from the host device is blocked. Only traffic through the VPN tunnel is allowed. (default)

•

Allowed—Public Internet traffic from the host device is allowed.

IPsec

The IP protocol that drives the Internet is inherently insecure. Internet Protocol

Security (IPsec), which is a standards-based protocol, secures communications of IP packets over public networks.

IPsec is a common network layer security control and is used to create a virtual private network (VPN).

The advantages of using the IPsec feature includes:

•

Data Protection: Data Content Confidentiality allows you to protect your data from any unauthorized view, because the data is encrypted (encryption algorithms are used).

•

Access Control: Access Control implies a security service that prevents unauthorized use of a Security Gateway, a network behind a gateway or bandwidth on that network.

•

Data Origin Authentication: Data Origin Authentication verifies the actual sender, thus eliminating the possibility of forging the actual sender’s identification by a third-party.

•

Data Integrity: Data Integrity Authentication allows both ends of the communication channel to confirm that the original data sent has been received as transmitted, without being tampered with in transit. This is achieved by using authentication algorithms and their outputs.

The IPsec architecture model includes the Sierra Wireless AirLink gateway as a remote gateway at one end, communicating through a VPN tunnel with a VPN gateway at the other end. The remote gateway is connected to a remote network and the VPN is connected to the local network. You can configure up to three remote subnets.

4118967

Rev 4 Jun.16

VPN Configuration

The IPsec VPN employs the IKE (Internet Key Exchange) protocol to set up a

Security Association (SA) between the AirLink gateway and a Cisco (or Cisco compatible) enterprise VPN server. IPsec has two phases for setting up an SA between peer VPNs. Phase 1 creates a secure channel between the AirLink gateway VPN and the enterprise VPN, thereby enabling IKE exchanges. Phase 2 sets up the IPsec SA that is used to securely transmit enterprise data.

Note: If you configure custom settings, they are saved and the tunnel can be disabled and re-enabled without needing to re-enter the settings. For a successful configuration, all settings for the VPN tunnel must be identical between the AirLink gateway VPN and the enterprise VPN server.

You can also configure VPN Failover for IPsec VPN tunnels. For more information, see

VPN Failover on page 134.

To configure an IPsec VPN tunnel:

In ACEmanager, go to VPN.

Select the VPN you want to configure (1, 2, 3, 4, or 5).

In the VPN Type field, select IPsec Tunnel. The screen expands to show the

IPsec Tunnel fields.

123

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

124

Figure 6-2: ACEmanager: VPN > VPN 1 > IPsec Tunnel

See the following table for instructions on completing the IPsec Tunnel fields.

Once the configuration is complete:

Click the Set VPN Policy button.

4118967

Field

General

VPN # Type

VPN # Status

Set VPN Policy

VPN Configuration

b. Check the VPN Status field to confirm the status of the VPN connection.

Description

Use this field to select the type of VPN tunnel. If you configure custom settings, they are saved and the tunnel can be disabled and re-enabled without needing to re-enter the settings.

Options are:

•

Tunnel Disabled (default)

•

IPsec Tunnel

•

GRE Tunnel

•

SSL Tunnel (only available for VPN 1)

Status of the VPN connection:

•

Disabled—VPN is disabled (default)

•

Not Connected—The VPN failed to connect. This could be because of a mismatch in the configuration between the client and the server, no data connection on the device, etc.

•

Connected—The VPN is connected and ready to transmit traffic.

•

Configuration Error—This status appears when:

•

Two VPNs have the same Local Address and Remote Address

•

More than one VPN has the remote address set to “0.0.0.0”

When either of these errors exist, only the first of the conflicting VPNs is operational.

To determine which VPNs are in conflict:

1.Go to Admin > Configure Log.

2. For the VPN Subsystem, ensure that Display in Log is set to Yes. The Verbosity can be either Info or Debug.

3. Click View Log.

4. The resulting log shows you which VPNs are in conflict.

After completing the VPN Configuration:

Click this button to apply the new settings.

Check the VPN Status field to confirm the status of the VPN connection. (See

VPN #

Status .)

Rev 4 Jun.16

125

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Field

VPN Gateway

Address

Pre-shared Key 1

My Identity Type

My Identity - IP or

My Identity - FQDN

Peer Identity Type

Description

The IP address or FQDN (Fully Qualified Domain Name) of the server that this VPN client connects to. This address must be open to connections from the AirLink gateway. The default VPN Gateway IP Addresses are static address on Sierra Wireless Servers. They are:

VPN Gateway IP Address

208.81.123.21

208.81.123.22

208.81.123.26

208.81.123.23

208.81.123.24

You can use these default IP addresses to confirm that an IPsec connection can be established with your wireless configuration before making any configuration changes, and as an example to model your VPN configuration after.

The pre-shared key (PSK) is used to initiate the VPN tunnel.

•

Pre-shared key length: Maximum supported length is 128 characters.

•

Valid characters are: 1234567890abcdefghijklmnopqrstuvwxyzABCDEFGHIJKLM

NOPQRSTUVWXYZ!%&-~@#$^*

•

Invalid characters: ><?

Options are:

•

IP (default) — The My Identity - IP field appears with the WAN IP address assigned by the carrier

•

FQDN — The My Identity - FQDN field appears. Enter a fully qualified domain name

(FQDN) e. g., modemname.domainname.com

•

User FQDN — The My Identity - FQDN field appears. Enter a User FQDN whose values should include a username (e.g. [email protected])

•

My Identity - IP appears only when IP is selected from the My Identity Type drop-down menu. The WAN IP address assigned by the carrier appears.

•

My Identity - FQDN appears only when User FQDN or FQDN is selected from the My

Identity Type drop-down menu. Enter an FQDN or User FQDN.

Note: If you are using a FQDN for your device (My Identity) either:

•

Set up a Dynamic DNS on the Services > Dynamic DNS tab. (See

Global DNS on page 105.) or

•

Use a DNS server as your domain host

Required in some configurations to identify the client or peer side of a VPN connection.

Options are:

•

IP (default) — The Peer Identity - IP field appears with the IP address of a VPN server set up by Sierra Wireless for your testing purposes

•

FQDN — The Peer Identity - FQDN field appears. Enter an FQDN

(e. g. modemname.domainname.com)

•

User FQDN — The Peer Identity - FQDN field appears. Enter a User FQDN whose values should include a username (e.g., [email protected])

126 4118967

VPN Configuration

Field

Peer Identity - IP or

Peer Identity - FQDN

Negotiation Mode

IKE Encryption

Algorithm

IKE Authentication

Algorithm

IKE Key Group

IKE SA Life Time

IKE DPD

Description

•

Peer Identity - IP appears only when IP is selected from the Peer Identity Type dropdown menu. The VPN Gateway IP Address appears.

•

Peer Identity - FQDN appears only when User FQDN or FQDN is selected from the

Peer Identity Type drop-down menu. Enter the Peer FQDN or Peer User FQDN.

Enable this configuration to operate the onboard VPN under Aggressive mode. Aggressive mode offers increased performance at the expense of security.

Options are:

•

Main (default)

•

Aggressive

Determines the type and length of encryption key used to encrypt/decrypt ESP

(Encapsulating Security Payload) packets. 3DES supports 168-bit encryption. AES

(Advanced Encryption Standard) supports both 128-bit and 256-bit encryption.

Options are: DES, 3DES, AES-128 (default), and AES-256

MD5 is an algorithm that produces a 128-bit digest for authentication. SHA is a more secure algorithm that produces both 160-bit (SHA1) and 256-bit (SHA256) digests.

Options are: MD5, SHA1 (default), and SHA256

Options are: DH1, DH2 (default), or DH5

Determines how long the VPN tunnel is active in seconds.

Options are: 180 to 86400; Default: 7200

Dead Peer Detection (DPD)

Options are:

•

Disable (default)

•

Enable

When DPD is enabled, the AirLink gateway checks to see if the server is still present if there has been no traffic for a configured interval. If it does not receive an acknowledgment, it retries at 5 second intervals. If there is no acknowledgment after 5 retries, the status of the VPN is set to Not Connected and the device attempts to renegotiate IPSEC security parameters with its peer.

Default is Disabled.

Note: Sierra Wireless recommends that you Enable IKE DPD. Otherwise the AirLink gateway has no way of detecting that the connection to the VPN server is still available.

IKE DPD Interval

(seconds)

Local Address Type

Local Address

Local Address -

Netmask

Use this field to set the DPD interval (in seconds). If there has been no traffic for the period of time set in this field, the AirLink gateway retries checking with the server, as described in

IKE DPD .

Options are: 0 to 3600 (default is 1200)

If this field is set to 0, DPD monitoring is turned off (or disabled as described in the IKE

DPD section), but the AirLink gateway still responds to DPD requests from the server.

The network information of the device. Options are: Use the Host Subnet, Single Address, and Subnet Address (default)

Device subnet address

Device subnet mask information

Default: 255.255.255.0

Rev 4 Jun.16

127

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Field Description

Remote Address Type

The network information of the IPsec server behind the IPsec gateway.

Options are: Subnet Address (default) and Single Address

Remote Address

The IP address or subnet of the device(s) connected to the gateway

If the remote address is 0.0.0.0, the remote address netmask should also be 0.0.0.0.

Note that you can only have one remote address of 0.0.0.0 for all the VPNs.

Default values are:

VPN

Remote Address

10.11.12.0

10.11.13.0

10.11.14.0

10.11.15.0

10.11.16.0

Remote Address -

Netmask

Perfect Forward

Secrecy

IPsec Encryption

Algorithm

IPsec Authentication

Algorithm

Remote subnet mask information

Default: 255.255.255.0

0.0.0.0 is allowed for the remote address subnet mask as long as the remote address is also 0.0.0.0.

Provides additional security through a DH shared secret value. When this feature is enabled, one key cannot be derived from another. This ensures previous and subsequent encryption keys are secure even if one key is compromised. Options are: Yes (default) or

No.

Determines the type and length of encryption key used to encrypt/decrypt ESP

(Encapsulating Security Payload) packets. 3DES supports 168-bit encryption. AES

(Advanced Encryption Standard) supports both 128-bit and 256-bit encryption.

Options are: None, DES, 3DES, AES-128 (default), and AES-256.

Can be configured with MD5 or SHA1. MD5 is an algorithm that produces a 128-bit digest for authentication. SHA is a more secure algorithm that produces both 160-bit (SHA1) and

256-bit (SHA256) digests.

Options are: None, MD5, SHA1 (default), and SHA 256.

IPsec Key Group

IPsec SA Life Time

Determines how the AirLink gateway VPN creates an SA with the VPN server. The DH

(Diffie-Hellman) key exchange protocol establishes pre-shared keys during the phase 1 authentication. The AirLink gateway supports three prime key lengths, including Group 1

(768 bits), Group 2 (1,024 bits), and Group 5 (1,536 bits). Options are: None, DH1, DH2

(default), or DH5.

Determines how long the VPN tunnel is active in seconds

Options are: 180 to 86400; Default: 7200

Additional Remote Subnets

Remote Subnet 2

Address type

Remote Subnet 2

Address

The network information for subnet 2 IPsec server behind the IPsec gateway.

Options are: Subnet Address (default) and Single Address

The IP address for the subnet 2 device behind the gateway

128 4118967

VPN Configuration

Field

Remote Subnet 2

Address - Netmask

Remote Subnet 3

Address type

Remote Subnet 3

Address

Remote Subnet 3

Address - Netmask

Description

Remote subnet 2 mask information

Default: 255.255.255.0

The network information for subnet 3 IPsec server behind the IPsec gateway.

Options are: Subnet Address (default) and Single Address

The IP address for the subnet 3 device behind the gateway

Remote subnet 3 mask information

Default: 255.255.255.0

GRE

The AirLink gateway can act as a Generic Routing Encapsulation (GRE) endpoint, providing a means to encapsulate a wide variety of network layer packets inside IP tunneling packets. With this feature you can reconfigure IP architectures without worrying about connectivity. GRE creates a point-to-point link between routers on an IP network.

To configure GRE:

In ACEmanager, go to VPN.

Select the VPN you want to configure (1, 2, 3, 4, or 5).

In the VPN Type field, select GRE. The screen expands to show the GRE fields.

Rev 4 Jun.16

Figure 6-3: ACEmanager: VPN > VPN1 > GRE Tunnel

See the following table for instructions on completing the GRE fields.

129

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Once the configuration is complete, either:

· Click the Set VPN Policy button.

· Reboot the AirLink gateway.

Field

VPN # Type

VPN # Status

Set VPN Policy

Description

Options are: Tunnel Disabled or GRE Tunnel. Enabling the GRE Tunnel will expose other options for configuring the tunnel.

Indicates the status of the GRE tunnel on the device

Options are: Disabled, Connected or Not Connected

After completing the VPN Configuration:

Click this button to apply the new settings (or reboot the device).

Check the VPN Status field to confirm the status of the VPN connection. (See VPN #

Status

VPN Gateway

Address

The IP address of the device that this client connects to. This IP address must be open to connections from the device.

Remote Address Type

The network information of the GRE server behind the GRE gateway

Remote Address

Remote Address -

Netmask

The IP address of the device behind the gateway

The subnet network mask of the device behind the GRE gateway

Note: Never use a 16-bit subnet mask: GRE tunnel establishment will fail.

GRE TTL

GRE time to live (TTL) value is the upper bound on the time that a GRE packet can exist in a network. In practice, the TTL field is reduced by one on every router hop. This number is in router hops and not in seconds.

SSL Tunnel

Note: SSL Tunnel configuration is only available on VPN 1.

The SSL tunnel is implemented using OpenVPN. OpenVPN uses SSL/TLS to facilitate key exchange and supports up to 256-bit encryption. OpenVPN is capable of crossing network address translators (NATs) and firewalls. Peers can authenticate each other using pre-shared keys, certificates, or username and password.

The AirLink gateway client authenticates the server using a PKI certificate. The server likewise authenticates the client. The Root CA certificate for the server certificate must be loaded on the device.

To configure an SSL VPN tunnel:

In ACEmanager, go to VPN.

Select the VPN 1.

130 4118967

VPN Configuration

In the VPN Type field, select SSL Tunnel. The screen expands to show the

SSL Tunnel fields.

Rev 4 Jun.16

Figure 6-4: ACEmanager: VPN > VPN1 > SSL Tunnel

See the following table for instructions on completing the SSL Tunnel fields.

Once the configuration is complete, either:

· Click the Set VPN Policy button.

· Reboot the AirLink gateway.

131

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Field

General

VPN 1 Type

Description

VPN 1 Status

Set VPN Policy

SSL Role

Tunnel Mode

Protocol

Peer Port

Options are: Tunnel Disabled or SSL Tunnel. Enabling the SSL Tunnel will expose other options for configuring the tunnel.

Indicates the status of the SSL tunnel on the device

Options are: Disabled, Connected or Not Connected

After completing the VPN Configuration:

Click this button to apply the new settings (or reboot the device).

Check the VPN Status field to confirm the status of the VPN connection. (See VPN 1

Status

The AirLink gateway can only be an SSL client. Default: Client

The Tunnel Mode is set to “Routing”.

Displays the protocol used for configuration. Only supports UDP

The Peer Port is the UPD port on the peer device.

Peer Identity

Enter the IP address or Fully Qualified Domain Name (FQDN) of the peer device.

Encryption Algorithm

Options are: DES, Blowfish, DES, Cast128, AES-128, and AES-256

Authentication

Algorithm

Compression

Options are: MD5, SHA-1, and SHA-256

Options are: LZ0 or NONE

Load Root Certificate

Loads the server root CA (Certificate Authority) certificate

When you click the button, a window pops up and enables you to browse and select the file containing the root CA certificate.

Root Certificate Name

Displays the name of the most recently uploaded root certificate

Client Certificate

Enables or disables use of a client certificate.

Load Client

Certificate

This field appears only if Client Certificate is enabled.

Loads the client certificate

When you click the button, a window pops up and enables you to browse and select the file containing the client certificate.

Displays the number of the most recently uploaded client certificate.

Client Certificate

Number

Load Client

Certificate Key

Client Certificate Key

Name

This field appears only if Client Certificate is enabled.

Loads the client certificate key

When you click the button, a window pops up and enables you to browse and select the file containing the client certificate key.

Displays the name of the most recently uploaded client certificate key

User Name

User Password

The user name required for client authentication

The user password required for client authentication

132 4118967

VPN Configuration

Field

Additional TLS

Authentication

Load Client TLS Key

Description

Enables or disables use of Transport Layer Security (TLS) authentication.

This field appears only if Additional TLS Authentication is enabled.

Loads the client TLS key

When you click the button, a window pops up and enables you to browse and select the file containing the client TLS key.

Client TLS Key Name

Displays the name of the most recently uploaded client TLS key

Advanced

Tunnel-MTU

MSS Fix

Fragment

Allow Peer Dynamic

Default: 1500 bytes

Default: 1400 bytes

Default: 1300 bytes

Options are: Enable or Disable

Re-negotiation

(seconds)

Ping Interval

(seconds)

Tunnel Restart

(seconds)

NAT

Default: 86400 (24 hours)

This is the keep-alive sent by the client. Default: 0 seconds

Enter the time for a tunnel restart (unit in seconds)

Options are: Enable or Disable. Note that this is a Mobile Network Operator NAT, not a local NAT

Load Root Certificate

Note: The process is similar for uploading the client certificate, the client certificate key and the client TLS key.

To load a root certificate:

Click Load Root Certificate.

The following dialog-box appears.

Rev 4 Jun.16

Select the appropriate file for your device.

Click Upload File to Device.

133

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

VPN Failover

VPN Failover is only available for IPsec VPN tunnels. To use this feature, configure a primary and a secondary VPN tunnel. Dead Peer Detection (DPD) verifies the status of the primary connection. If the primary VPN goes down (i.e.

DPD detects that the end device is not responding) traffic is automatically switched to the secondary (backup) VPN tunnel. DPD continues to ping the primary VPN responder. If configured to do so, once the primary VPN tunnel is up, traffic automatically reverts to the primary VPN. Status fields in the

ACEmanager UI inform you of the current status of the two VPNs.

Primary VPN

Secondary VPN

Two IPsec VPN tunnels are configured, but only one is active at a time. The primary VPN is active unless DPD determines the responder is dead. In that case, traffic is

AirLink gateway switched to Secondary VPN.

DPD and VPN Failover configured on AirLink gateway

Switch

LAN

Subnet 1

Subnet 2

Figure 6-5: VPN Failover Configuration

To configure VPN Failover:

Configure two IPsec VPN tunnels. The one you want to designate as the primary VPN must have Dead Peer Detection configured. For the Secondary

VPN, you only need to configure the remote gateway address. For other settings, such as the local and remote subnets, the secondary VPN uses the same settings as the primary VPN.

For instructions on configuring IPsec VPN tunnels, see

IPsec on page 122.

Go to VPN > Failover and configure the first three fields. See the table following the screen shot for details.

Click Apply and reboot the AirLink gateway.

134 4118967

VPN Configuration

Figure 6-6: ACEmanager: VPN > Failover

Field

Primary VPN

Secondary VPN

Revertive

Primary VPN Status

Secondary VPN

Status

Description

ID of the primary VPN (for VPN Failover) i.e. VPN 1, VPN 2, VPN 3, VPN 4, VPN 5, or

None (None is the default.)

ID of the Secondary VPN (for VPN Failover) i.e. VPN 1, VPN 2, VPN 3, VPN 4, VPN 5, or

None (Default is None.)

When VPN Failover is configured and this field is set to Enable, traffic automatically switched from the Secondary VPN back to the primary VPN when the failure is resolved and the primary VPN tunnel is up again. Options are

•

Enable (default)

•

Disable

Status of the primary VPN:

•

Disabled—VPN Failover is disabled. (default)

•

Connecting—The VPN is trying to connect to the responder.

•

Active—The VPN tunnel is ready and transferring traffic.

•

Backup—This is currently the backup VPN connection.

•

Failed—Dead Peer Detection (DPD) has determined that the VPN responder is dead, or a ping sent to the VPN host failed.

•

Out of Service—There have been 5 DPD failures within an hour.

Status of the Secondary VPN:

•

Disabled—VPN Failover is disabled. (default)

•

Connecting—The VPN is trying to connect to the responder.

•

Active—The VPN tunnel is ready and transferring traffic.

•

Backup—This is currently the backup VPN connection.

•

Failed—Dead Peer Detection (DPD) has determined that the VPN responder is dead, or a ping sent to the VPN host failed.

•

Out of Service—There have been 5 DPD failures within an hour.

Rev 4 Jun.16

135

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Field Description

Overall VPN Status

Status of the overall VPN:

•

Disabled—VPN Failover is disabled. (default)

•

Connecting—One of the VPNs is trying to connect to the responder.

•

Active—One VPN tunnel is currently in use. The backup VPN is available.

•

Backup_Unavailable —One VPN tunnel is currently in use. The backup VPN is not available.

•

Out of Service—Neither the primary nor secondary VPN is operational.

•

N/A—The overall VPN status is temporarily not available. Click Refresh.

Number of Primary

VPN Failures

Number of times DPD has failed on the primary VPN since the device has been rebooted or the “Set VPN Policy” button was clicked

Number of Secondary

VPN Failures

Number of times DPD has failed on the Secondary VPN since the device has been rebooted or the “Set VPN Policy” button was clicked

Number of Switches to Primary VPN

Number of Switches to Secondary VPN

Number of times traffic was switched to the primary VPN since the device has been rebooted or the “Set VPN Policy” button was clicked

Number of times traffic was switched to the Secondary VPN since the device has been rebooted or the “Set VPN Policy” button was clicked

136 4118967

Rev 4 Jun.16

7: Security Configuration

The security tab covers firewall-type functions. These functions include how data is routed or restricted from one side of the device to the other, i.e., from computers or devices connected to the device

(LAN) and from computers or devices contacting it from a remote source (WAN). These features are set as rules.

Tip:

For additional security, Sierra Wireless recommends that you change the default password for ACEmanager. See

Change Password on page 285.

Solicited vs. Unsolicited

How the device responds to data being routed from one network connection to the other depends on the origin of the data.

•

If a computer on the LAN initiates a contact to a WAN location

(such as a LAN connected computer accessing an Internet web site), the response to that contact is solicited.

•

If, however, a remote computer initiates the contact (such as a computer on the Internet accessing a camera connected to the device), the connection is considered unsolicited.

Port Forwarding

In Port Forwarding, any unsolicited data coming in on a defined

Public Port is routed to the corresponding private port and IP of a host connected to the LAN. You can forward a single port or a range of ports.

Note: Port Forwarding requires Private Mode. See

Private and Public Mode on page 87.

Internet

Figure 7-1: Port Forwarding

AirLink gateway

Host IP/Destination Computer

137

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Note: You can set up a maximum of 48 port forwarding rules, 24 on the Port Forwarding screen and an additional 24 on the Extended Port Forwarding screen.

Single port

To define a port forwarding rule for a single port:

In ACEmanager, go to Security > Port Forwarding.

138

Figure 7-2: ACEmanager: Security > Port Forwarding (Single Port)

In the Port Forwarding field, select Enable.

Click “Add More” to display a rule line.

In the Public Start Port field, enter the desired public network port number.

Values between 1 and 65535 are supported, although Sierra Wireless recommends using a value greater than 1024.

Unsolicited data coming in on this port is forwarded to the port you select in the Private Start Port field.

In the Public End Port field, enter 0.

Select the desired protocol (see

Protocol on page 141):

· TCP

· UDP

· TCP & UDP

Enter the IP address of the computer you want to forward data to.

In the Private Start Port field, enter the number of the port on the destination computer that you want to forward data to.

Click Apply.

You do not need to reboot immediately, if you have additional changes to make, but port forwarding does not take effect until the device is rebooted.

The Port Forwarding screen allows for 24 port forwarding rules.

10. Optional—If you need additional port forwarding rules, click Extended Port

Forwarding on the left menu, and continue adding rules, up to a total over both screens of 48.

4118967

Security Configuration

Figure 7-3: ACEmanager: Security > Extended Port Forwarding

11. Reboot.

Range of ports

To define a port forwarding rule for a range of ports:

In ACEmanager, go to Security > Port Forwarding.

Rev 4 Jun.16

Figure 7-4: ACEmanager: Security > Port Forwarding (Port Range)

In the Port Forwarding field, select Enable.

Click “Add More” to display a rule line.

Set the port range for incoming data:

In the Public Start Port field, enter the desired public network port number. Values between 1 and 65535 are supported, although Sierra

Wireless recommends using a value greater than 1024.

b. In the Public Port End field, enter the last public network port number in the range. The value you enter in the Public Port End field must be greater than the value in the Public Start Port field, or ALEOS rejects the selection.

139

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Unsolicited data coming in on ports in this range are forwarded to a range of ports, starting with the port you select in the Private Start Port field.

Select the desired protocol (see

Protocol on page 141):

· TCP

· UDP

· TCP & UDP

Enter the IP address of the computer you want to forward data to.

To forward a port to a local ALEOS Service, set the Host IP to 127.0.0.1.

In the Private Start Port field, enter the starting port number for the range of ports on the destination computer that you want to forward data to.

If you want to add another range, click Add More to display a new rule line.

Click Apply.

The Port Forwarding screen allows for 24 port forwarding rules.

10. Optional—If you need additional port forwarding rules, click Extended Port

Forwarding on the left menu, and continue adding rules, up to a total over both screens of 48.

140

Figure 7-5: ACEmanager: Security > Extended Port Forwarding

11. Reboot.

You do not need to reboot immediately, if you have additional changes to make, but port forwarding does not take effect until the device is rebooted.

Note: Sierra Wireless recommends that the total number of port forwardings be fewer than

1000 ports, including single port forwarding and port forwarding within a range.

4118967

Rev 4 Jun.16

Security Configuration

Field Description

Port Forwarding

Enables port forwarding rules. Options are Enable and Disable

(default).

Public Start Port

Port on the public network or starting port on the public network for a range of ports.

•

Supported values: 1–65535

(Recommended values: greater than 1024)

Public End Port

Ending port for a range of ports on the public network.

•

For a single port forwarding, this field must be 0.

•

For a range of ports, this value must be greater than the value in the Public Start Port field.

Protocol

The protocol to be used with the forwarded port:

•

TCP—Only those unsolicited data requests using TCP are forwarded

•

UDP—Only those unsolicited data requests using UDP are forwarded

•

TCP & UDP—Unsolicited data requests using either TCP or

UDP are forwarded

Host IP

IP address of the computer (or device) you want to forward data to.

Private Start Port

Port on the destination computer used as the port for single port forwarding rules, or as the start port for a port forwarding range.

Port Forwarding Example

The following example shows you how to configure a port forward rule for a range of 6 ports on an Ethernet-connected device:

In ACEmanager, go to Security > Port Forwarding, and enable Port

Forwarding.

Click “Add More” to display a rule line.

Enter 8080 for the Public Start Port.

Enter 8085 for the Public End Port.

Select TCP & UDP.

Enter 192.168.13.100 as the Host IP.

Enter 80 as the Private Start Port.

141

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

142

Figure 7-6: ACEmanager: Port Forwarding example

Click Apply.

Reboot.

You do not need to reboot immediately, if you have additional changes to make, but port forwarding does not take effect until the device is rebooted.

An unsolicited TCP and UDP data request coming in to the AirLink gateway on port 8080 is forwarded to the LAN connected device, 192.168.13.100, at port 80.

In addition, unsolicited data requests coming in from the Internet on ports 8081,

8082, 8083, 8084, and 8085 are forwarded to ports 81, 82, 83, 84, and 85 respectively.

DMZ

The DMZ is used to direct unsolicited inbound traffic to a specific LAN device such as a computer running a web server or other internal application.

The DMZ with public mode is particularly useful for certain services like VPN, NetMeeting, and streaming video where the remote server may require a WAN connection to the LAN device rather than being NATed by the router. In public mode unsolicited traffic to hosts in the DMZ is permitted by default.

Options for DMZ are Automatic, Manual, and Disable.

Automatic uses the first connected device. If more than one host is available

(multiple Ethernet on a switch connected to the device and/or Ethernet with

USBnet) and you want to specify the host to use as the DMZ, select Manual and enter the IP address of the desired host.

4118967

Security Configuration

Field

DMZ IP

DMZ IP in use

Figure 7-7: ACEmanager: Security > Port Forwarding (DMZ)

Description

This field only appears if Manual is selected for the DMZ Enabled field; this field does not display if the DMZ is disabled. This is the IP address of the private mode host that should be used as the DMZ.

IP address of the host to which inbound unsolicited packets are sent

When the device passes the Network IP to the configured public host, the DMZ IP in Use displays the public IP.

Example of configuring the DMZ on an Ethernet connected device:

Enter 192.168.13.100 for the DMZ IP.

Select Ethernet as the Default Interface.

An unsolicited data request coming in to the AirLink gateway on any port is forwarded to the LAN device, 192.168.13.100, at the same port.

Note: The DMZ settings are independent of the number of Port Forward entries and can be used with port forwarding to pass anything not forwarded to specific ports.

Port Filtering—Inbound

Port Filtering

—

Inbound restricts unsolicited access to the AirLink gateway and all

LAN-connected devices.

You can enable Port Filtering to either block or allow specified ports. When enabled, all ports not matching the rule are allowed or blocked depending on the mode.

You can configure Port Filtering either on individual ports or for a range of ports.

Click Add More for each port filtering rule you want to add.

Rev 4 Jun.16

143

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Note: Inbound restrictions do not apply to responses to outbound data requests. To restrict outbound access, you need to set the applicable outbound filter.

Figure 7-8: ACEmanager: Security > Port Filtering - Inbound

Field Description

Inbound Port Filtering

Mode

Options are:

•

Disable (default)

•

Blocked Ports—ports though which traffic is blocked (Shown in Filtered Ports list)

•

Allowed Ports—ports through which traffic is allowed (Shown in Filtered Ports list)

Filtered Ports

Start Port

End Port

A single port or the first port in a range of ports on the public network (mobile network accessible)

The end of the range on the public network (mobile network accessible).

Warning:

Selecting Allowed Ports will *block* all ports not allowed, and will *prevent remote access* if the management ports are not allowed. To allow remote management, the allowed ports list should include 8088, 17339, 17336, and ACEmanager port 9191 (or the port you selected for ACEmanager).

Port Filtering — Outbound

Port Filtering

—

Outbound restricts LAN access to the external network, i.e., the

Internet.

Port Filtering can be enabled to block ports specified or allow specified ports.

When enabled, all ports not matching the rule will be allowed or blocked depending on the mode.

144 4118967

Security Configuration

Port Filtering can be configured on individual ports or for a range of ports. Click

Add More for each port filtering rule you want to add.

Note: Outbound restrictions do not apply to responses to inbound data requests. To restrict inbound access, you need to set the applicable inbound filter.

Field

Outbound Port

Filtering Mode

Start Port

End Port

Rev 4 Jun.16

Figure 7-9: ACEmanager: Security > Port Filtering - Outbound

Description

Allowed and blocked ports through which traffic is either allowed or blocked (respectively) are listed. Options are:

•

Disable (default)

•

Blocked Ports—ports though which traffic is blocked (Shown in Filtered Port s list)

•

Allowed Ports—ports through which traffic is allowed (Shown in Filtered Port s list)

Note: Outbound IP filter supports up to 9 ports.

The first of a range or a single port on the LAN

The end of the range on the LAN

Trusted IPs—Inbound (Friends)

Trusted IPs

—

Inbound restricts unsolicited access to the AirLink gateway and all

LAN connected devices.

Tip:

Trusted IPs-Inbound was called Friends List in legacy AirLink products.

When enabled, only packets with source IP addresses matching those in the list or range of trusted hosts will have unrestricted access to the AirLink gateway and/ or LAN connected devices.

145

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Note: Inbound restrictions do not apply to responses to outbound data requests. To restrict outbound access, you need to set the applicable outbound filter.

Figure 7-10: ACEmanager: Security > Trusted IPs > Inbound (Friends)

Field

Inbound Trusted IP

(Friends List) Mode

Non-Friends Port

Forwarding

Inbound Trusted IP

List

Inbound Trusted IP

Range

Range Start

Range End

Description

Disables or Enables port forwarding rules. Options are Disable (default) or Enable.

Non-Friends port forwarding is like an allow rule for any of the forwarded ports. If it is enabled, the port forwarding rules apply to all incoming packets. If it is disabled, only

Inbound Trusted List (or Range) IPs get through. Options are Disable (default) or Enable.

Enter a single trusted IP address for example 64.100.100.2. Click Add More to add additional IP addresses to the list.

Use this section of the page to enter a range of trusted IP addresses.

Specify the start and end IP addresses for the trusted IP address range, for example, entering 64.100.10.2 as the Range Start and 64.100.10.15 as the Ranges End would allow

64.100.10.5 but would not allow 64.100.10.16.

146 4118967

Security Configuration

Trusted IPs—Outbound

Trusted IPs

—

Outbound restricts LAN access to the external network (Internet).

When enabled, only packets with the destination IP addresses matching those in the list of trusted hosts will be routed from the LAN to the external location.

Note: Outbound restrictions do not apply to responses to inbound data requests. To restrict inbound access, you need to set the applicable inbound filter.

Figure 7-11: ACEmanager: Security > Trusted IPs - Outbound

Field

Outbound Firewall

Mode

Outbound Trusted IP

List

Description

Disables or enables the Outbound Firewall

Options are:

•

Disable (default)—Allows all outbound traffic

•

Enable—Only outbound traffic destined for an IP address on the Trusted IP list is allowed. All other outbound traffic is blocked.

Each entry can be configured to allow a single IP address (e.g., 64.100.100.2) Click Add

More to add additional IP addresses to the list.

MAC Filtering

MAC filtering restricts LAN connection access. You can create a list of up to 20 devices that are allowed a connection based on their MAC address. When MAC filtering is enabled, devices not on the allowed list are explicitly blocked. Hosts directly connected to the device but not in the Allowed list may show an active physical connection, but are blocked from sending traffic of any kind to the device or any other host connected to the device.

Rev 4 Jun.16

147

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Figure 7-12: ACEmanager: Security > MAC Filtering

Field Description

MAC Filtering

Enable or disable (default) MAC Filtering

MAC Address allowed

List

Allows devices with the MAC Addresses listed to connect to the host and transfer data. Add

MAC addresses by clicking on the Add More button. When adding MAC addresses, use a colon between the digit groups, for example 01:23:45:67:89:ab.

Note: After adding all the desired MAC addresses, reboot the device. The MAC Address allowed List takes effect after the device is rebooted.

MAC Address

This is the MAC Address of the interface adapter on a computer or other device.

Tip:

You can use the Status > LAN page to obtain the MAC addresses of DHCP connected devices.

148 4118967

8: Services Configuration

The Services tab sections allow the configuration of external services that extend the functionality of the AirLink Device.

ALMS (AirLink Management

Service)

Figure 8-1: ACEmanager: Services > ALMS

Field

General

AirLink

Management

Service

Description

Disables or enables ALMS management by disabling or enabling periodic deviceinitiated communication with the ALMS server.

Rev 4 Jun.16

149

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Field

Server URL

Description

The ALMS server URL address. By default, this is: https://na.m2mop.net/device/msci/com, which encrypts network traffic from ALEOS to ALMS.

Using an HTTPS URL enables Secure Socket Layer (SSL). When SSL is enabled

and the SSL Verify Peer Certificate

field is set to Enable, the validity of the server

certificate is checked. For more information, see SSL Verify Peer Certificate on page 151.

Note: The URL from earlier ALEOS versions, http://na.m2mop.net/device/msci, is still valid, but does not use SSL.

Device Initiated

Interval

(minutes)

ALMS Name

Status

This field determines how often the AirLink device checks for software updates and settings changes from ALMS. ALMS can also query the AirLink device at a regular interval if settings allow. Refer to AirLink Management Service documentation for more information. Default: 1440 minutes (24 hours).

Use this field to assign a name of your choice to the AirLink device.This name is used by the ALMS server to identify your device. By default, this field is blank.

You can also use an AT command to assign or query the name. See *AVMS_NAME on page 385.

Displays the status of the ALMS connection:

•

Success— Device successfully contacted ALMS during its latest communication.

•

Disable— ALMS communications are disabled. (Appears when the AirLink

Management Service drop-down menu is set to Disable.)

•

[ALEOS] Waiting for connectivity — This transitory status appears when the device is in Connect-on-traffic mode and is trying to connect to the network for an ALMS check-in. (See

Always on connection on page 62.) When the device

connects to the network, the ALMS check-in is sent and the status changes to

Success or an error message, if there is a problem with the connection.

For a list of error messages, see

page 441 .

Advanced

Auto

Synchronize

Configuration

This field allows you to choose when changes to the configuration are propagated to

ALMS.

•

Enable—Changes to the configuration are propagated as soon as possible and do not wait for the next communication period (as configured in the Device

Initiated Interval field). This may result in more frequent communication with

ALMS. (default)

•

Disable—Changes to the configuration are propagated to ALMS at the device initiated interval rate.

150 4118967

Rev 4 Jun.16

Services Configuration

Field

SSL Verify Peer

Certificate

Connect

Description

This field has no effect unless an HTTPS URL is used for the

Server URL

Using an HTTPS URL (for example, https://na.m2mop.net/device/msci/com ) as the server URL enables Secure Socket Layer (SSL). When SSL is enabled, use this field to set the SSL certificate validation.

•

Enable—The validity of the server certificate is checked during the SSL negotiation. (default)

If the certificate is not valid, communication with the ALMS server is terminated.

For more information, see

[HTTP] SSL peer certificate or SSH remote key was not OK on page 442.

•

Disable—The validity of the server certificate is not checked during the SSL negotiation. The SSL communication proceeds even if the server presents a non-validated certificate.

The Connect button enables you to manually connect an AirLink device to ALMS.

This may be useful for troubleshooting the connection between the platform and the remote device and confirming that AAF scripts or jobs created are executing as expected on ALMS.

AAF

M3DA Protocol

Password

M3DA Protocol Password

This password must be configured on the AirLink device and on ALMS. The default password is 12345.

Displays the current manual connection status.

Manual

Connection

Status

Connect

The Connect button enables you to manually connect an AirLink device to ALMS.

This may be useful for troubleshooting the connection between the platform and the remote device and confirming that AAF scripts or jobs created are executing as expected on ALMS.

151

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

ACEmanager

152

Figure 8-2: ACEmanager: Services > ACEmanager

Field Description

General

Remote Access

Configure ACEmanager remote access (over the WAN link)

Options are:

•

Disable (default)

•

HTTPS Only

•

Both HTTP and HTTPS

Local Access

Configure ACEmanager local access (Ethernet, USBnet, or Serial/DUN)

Options are:

•

HTTPS Only

•

Both HTTP and HTTPS (default)

HTTP Port

HTTPS Port

Configure the HTTP port for ACEmanager access. Reboot the device after applying the port change.

Default value is 9191.

Configure the HTTPS port for ACEmanager access. Reboot the device after applying the port change.

Default is 9443.

4118967

Rev 4 Jun.16

Services Configuration

Field Description

Session Idle

Timeout

(minutes)

Maximum Login

Attempts

Number of failed login attempts allowed before the user account is temporarily locked

Options are:

•

0—The account lock out feature is disabled.

•

1–5—Maximum number of failed login attempts before the user account is locked for the length of time specified in the

Unlock Time (seconds) field

Unlock Time

(seconds)

If ACEmanager is idle for the configured timeout, it automatically logs out and returns you to the login screen. Options are:

•

0–60 (minutes) Default is 15.

If you set the Session Idle Timeout to zero (0), the session remains active until you manually log out.

The length of time (in seconds) that the user account is locked after the maximum number of failed login attempts (configured in

Maximum Login Attempts

)

Options are:

•

1–3600 (1 hour)

Default is 120 (2 minutes)

Advanced

Custom

Certificate

Enabling this feature allows you to load a custom SSL certificate. (Some restrictions apply; see Note below for details.)

Options are:

•

Enable—Additional fields appear that allow you to load a custom SSL certificate and a custom private key. The ACEmanager web server uses this custom certificate for authentication during HTTPS communication, instead of the default certificate.

•

Disable—The ACEmanager web server uses the default SSL certificate for authentication during HTTPS communication. (default)

Note: The custom certificate and private key must meet the following conditions:

•

The certificate must be an X.509

certificate

•

The certificate and the private key must be in .pem format, and they must be in separate files.

•

There is no limit to the size of the private key, but the larger the key, the more the performance is affected. Sierra Wireless recommends that the key does not exceed 2048 bits.

Load Custom

Certificate

Note: The gateway supports pre-defined cipher suites using 128-bit cipher algorithms.

This field only appears when the Custom Certificate field is set to Enable.

To load a custom SSL certificate:

Click Load Custom Certificate.

Click Browse... and navigate to the SSL certificate file.

Click Upload file to device.

Once you have uploaded the custom certificate and the custom private key, click Apply and reboot the device.

153

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Field

Custom

Certificate

Name

Load Custom

Private Key

Description

This field only appears when the Custom Certificate field is set to Enable.

Displays the name of the custom certificate.

Custom Private

Key Name

This field only appears when the Custom Certificate field is set to Enable.

Allows you to enter a custom private key (Some restrictions apply; see Custom

Certificate on page 153 for details.)

To load a custom private key:

Click Load Private Key.

Click Browse... and navigate to the private key file.

Click Upload file to device.

Once you have uploaded the custom certificate and the custom private key, click Apply and reboot the device.

This field only appears when the Custom Certificate field is set to Enable.

Displays the name of the private key.

Power Management

The AirLink RV50 gives you a number of options for managing power usage, depending on your application and hardware configuration. For example, you can use the Services > Power Management screen to configure the RV50 to automatically enter standby mode based on the state of the ignition switch, an I/O input, low voltage input to the gateway, or time of day.

For additional power saving strategies, see

Additional Power Saving Strategies on page 161 or refer to the AirLink RV50 Hardware User Guide.

154 4118967

Services Configuration

Figure 8-3: ACEmanager: Services > Power Management

Field Description

Ignition Shutdown Delay

Shutdown Delay after

Ignition off (seconds)

Set the delay (in seconds) between the time the ignition input goes low and the gateway shuts down.

•

Range: 1–43200 (12 hours)

•

Default is 1.

The timer is reset if the ignition comes on during the delay period.

Rev 4 Jun.16

155

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Field

Low Voltage

Description

Note: Changes to the low voltage settings take effect when you click Apply, but new values are not permanently stored on the gateway until it is rebooted. Also note that, after a change is made, the first reboot may take longer than usual.

Note: Exercise caution when setting the Low Voltage Standby fields. Before setting the Resume immediately at Voltage field, ensure that you have a power source readily available that can supply the configured voltage. The reset button is not available when the gateway is in standby mode, so you cannot use it reset the gateway to factory default settings. If you have inadvertently set the Resume Voltage too high, follow the instructions in

How do I get my gateway out of Low

Voltage Standby mode?

on page 430 to return your gateway to normal operation.

Low Voltage Standby

Mode

Use this field to chose a set of predefined values for low voltage standby mode or to enable the option to configure custom values.

•

Custom—Allows you to configure the values used for low voltage standby mode. For more information on the configurable fields, see

Standby Voltage (100 milliVolts)

Standby Qualification Period (seconds) , and Resume immediately at Voltage (100 milliVolts) . When configuring these fields, the difference between the number in the

Standby Voltage field and the number in the Resume immediately at Voltage field must be greater than 5, with the smaller number in the Low Voltage Standby Mode field. For example, if you enter 120 in the Resume immediately at Voltage field, the highest number you can enter in the Low Voltage Standby mode field is 114.

•

Automatic—The gateway uses preset values. (default)

•

Off —The gateway uses the lowest possible preset values for low voltage standby mode and enters standby mode if the voltage falls below 5.8 V.

Table 8-1: Low Voltage Standby Mode Configurable Ranges and Preset Values

Low Voltage

Standby Mode

Standby Voltage

(100 milliVolts)

Standby Qualification

Period (seconds)

Resume immediately at Voltage

(100 milliVolts)

Custom

Automatic

Off

58–294

Default is 90.

30–3600

Default is 30.

68 –300

Default is 105.

105

156 4118967

Services Configuration

Field

Standby Voltage (100 milliVolts)

Description

If the incoming voltage to the gateway is below the value set in this field for the period of

time set in the Standby Qualification Period (seconds)

field, the gateway goes into standby mode.

This field is read-only if the Low Voltage Standby Mode is set to Automatic or Off. If Low

Voltage Standby Mode is set to Custom, the valid range is:

•

58—294 hundreds of milliVolts

•

Default value depends on the setting in the Low Voltage Standby Mode field. See

Table 8-1

Enter the value in tenths of Volts. For example, for 11.5 V, enter 115.

The difference between the number in the Standby Voltage field and the number in the

Resume immediately at Voltage (100 milliVolts) field must be greater than 5, with the

smaller number in the Low Voltage Standby Mode field. For example, if you enter 120 in the

Resume immediately at Voltage field, the highest number you can enter in the Low Voltage

Standby mode field is 114.

Standby Qualification

Period (seconds)

Set the time period (in seconds) that the voltage to the gateway is below the value set in

the Standby Voltage (100 milliVolts)

field before the gateway goes into standby mode.

This field is read-only if the Low Voltage Standby Mode is set to Automatic or Off. If Low

Voltage Standby Mode is set to Custom, the valid range is:

•

30—3600 seconds

•

Default is 30.

Resume immediately at Voltage

(100 milliVolts)

Set the voltage at which the gateway exits standby mode and resumes normal operation.

This field is read-only if the Low Voltage Standby Mode is set to Automatic or Off. If Low

Voltage Standby Mode is set to Custom, the valid range is:

•

68—300 hundreds of milliVolts

•

Default value depends on the setting in the Low Voltage Standby Mode field. See

Table 8-1

Enter the value in tenths of Volts. For example, for 12.5 V, enter 125.

The difference between the number in the

Standby Voltage (100 milliVolts) field and the

number in the Resume immediately at Voltage field must be greater than 5, with the smaller number in the Low Voltage Standby Mode field. For example, if you enter 120 in the

Resume immediately at Voltage field, the highest number you can enter in the Low Voltage

Standby mode field is 114.

Standby

Use Standby Mode

Select the type of Standby mode you want to configure

Options are:

•

Disable (default)

•

Timed

•

I/O

•

I/O + Timed

Changes take effect when you click Apply. No reboot is required.

Note: You cannot set this field to I/O or I/O + Timed if the I/O line is already being used by

the Relay Output 1

or by the Pull-up for I/O 1 .

Rev 4 Jun.16

157

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Field

Timed

Description

Mode

Wake Time

Return to Standby

Repeat Period

Select the Mode:

•

Hourly—

Wake Time and Return to Standby

operate on an hourly basis

•

Daily—

Wake Time and Return to Standby

operate on an daily basis

•

Custom—Provides the option set a test period to repeat the Wake/Standby cycle

Set the time (hours:minutes on a 24 hour clock) at which the gateway wakes up.

If you selected Hourly in the Mode field, set the minutes (the hour portion is ignored) and

the gateway wakes up every hour at the configured time.

If you selected Daily in the Mode field, the gateway wakes up every day at the configured

time.

Set the time (hours:minutes on a 24 hour clock) at which the gateway goes into standby mode.

If you selected Hourly in the Mode field, set the minutes (the hour portion is ignored) and

the gateway goes into standby mode every hour at the configured time.

If you selected Daily in the Mode field, the gateway goes into standby mode every day at

the configured time.

Note: There must be at least 5 minutes between the Wake Time

and the Return to

Standby time.

This field only appears if you select Custom in the Mode

field.

Use this field to configure how often the

Wake Time

Return to Standby

cycle is repeated.

The options are:

•

2 Hours (default)

•

3 Hours

•

4 Hours

•

6 Hours

•

8 Hours

•

12 Hours

I / O

158 4118967

Services Configuration

Field

Wake when I/O is

Description

Select the I/O state that causes the gateway to wake. Options are:

•

High (default)

•

Low

Note: If the I /O line is already configured for another purpose, this I/O option is not available.

Delay return to

Standby (seconds)

Select the delay between the I/O state change and the gateway entering Standby mode (in seconds).

•

Range is 1–43200 (12 hours)

•

Default is 1 second.

Engine Hours — ALEOS can start and stop counting engine hours based on:

•

Voltage on power connector Pin 1 (Power pin) from the vehicle battery (Engine Hours On Voltage Level)

•

Voltage on power connector Pin 3 (Ignition Sense pin) (Engine Hours Ignition Enable)

If you configure both fields, both conditions must be met before the device begins counting engine hours.

For more information on the power connector pins, refer to the Hardware Configuration User Guide for your AirLink gateway.

Engine Hours On

Voltage Level

(100 milliVolt)

If you want to use this field to trigger counting engine hours, the AirLink gateway must be using the vehicle battery as a power source (i.e. Pin 1 [VCC] and Pin 2 [ground] on the

AirLink gateway’s power connector are connected to the vehicle battery).

Enter the voltage level above which the AirLink gateway starts counting engine hours.

When the voltage from the vehicle battery falls below that value, the device stops counting engine hours. Enter the desired value of the ignition in millivolts. For example, to set the voltage level at 13.0 volts, enter 130.

The default value is 0, which means the feature is disabled. Engine hours are not incremented based on the power pin voltage level.

Engine Hours Ignition

Enable

If Pin 3 (the ignition sense pin) on the AirLink gateway’s power connector is wired to the vehicle’s ignition switch, oil pressure switch, or some other digital input, you can use this field to trigger counting engine hours. The device starts counting engine hours when the voltage on Pin 3 is high and stops counting when the voltage is low (Ground or 0 volts). For more information on the power connector pins, refer to the Hardware User Guide for your

AirLink gateway.

Options are:

•

Disable (default) Engine hours are not incremented based on changes to Pin 3.

•

Enable

Rev 4 Jun.16

159

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Field

Engine Hours Value

(hours)

Description

Displays an estimate of the number of hours the engine has been running, based on either the input voltage from the vehicle battery or the voltage on the ignition sense pin, depending on which of the two previous fields you configured. For more information on the power connector pins, refer to the Hardware User Guide for your AirLink gateway.

You can also set the engine hours value to an initial value. The default value is 0. The maximum allowed value is 65535.

You can also use an AT Command to set this value. For more information, see

*ENGHRS on page 385.

Note: You can configure Events Reporting to send reports based on this value. For more information, see

Events Reporting Configuration on page 229.

Power Saving Modes

LED Power Saving

Mode

Set the LED Power Saving option:

•

Enable—When enabled, the Signal LED Is off when the signal strength is good or average, and the Network LED is off when the RV50 is connected to a network. The

LEDs still indicate:

Signal LED:

•

Poor signal: Flashing Amber

•

No signal: Flashing Red

Network LED:

•

Connecting: Flashing Green

•

No network available: Flashing Red

•

Disable—Signal LED and Network LED indicate all states (default)

Signal LED:

•

Good signal: Solid Green

•

Average signal: Solid Amber

•

Poor signal: Flashing Amber

•

No signal: Flashing Red

Network LED:

•

LTE network: Solid Green

•

3G or 2G network: Solid Amber

•

Connecting: Flashing Green

•

No network available: Flashing Red

Note: For a complete description of LED behavior, refer to the AirLink RV50 Hardware

User Guide.

Processor Power

Savings Mode

Recommended for customers who require the lowest possible active/idle power consumption, for example, in battery or solar powered applications.

Enabling this feature saves energy by reducing performance where possible. The default setting (Disable) favors performance, but increases power consumption.

160 4118967

Rev 4 Jun.16

Services Configuration

Additional Power Saving Strategies

If the following table lists features, that if not used in your application, can be turned off/disabled to minimize power consumption.

Feature Default Setting Location in ACEmanager

GPS

Ethernet port

Off

GPS > Global Settings

See

GPS Service on page 208.

LAN > Ethernet > General

See

Ethernet Port on page 97.

Ethernet Link Setting

(data rate)

Auto 10/100/1000 LAN > Ethernet > Advanced

See

Ethernet 1 Link Setting on page 99.

USB port On

Serial port On

LAN > USB > General

See

USB Device Mode on page 101.

Serial > Port Configuration

See

Serial Port on page 248.

Dynamic DNS

Dynamic DNS allows an AirLink gateway WAN IP address to be published either to a proprietary Sierra Wireless dynamic DNS service called IP Manager, or to an alternate 3rd party Mobile Network Operator.

Whether you have one Sierra Wireless AirLink gateway or multiple devices, it can be difficult to keep track of the current IP addresses especially if the addresses are not static but change every time the devices connect to the mobile network. If you need to connect to a specific gateway, or the device behind it, it is much easier when you have a domain name (car54.mydomain.com, where are you?).

Reasons to Contact or Connect to a Device:

•

Requesting a location update from a delivery truck

•

Contacting a surveillance camera to download logs or survey a specific area

•

Triggering an oil derrick to begin pumping

•

Sending text to be displayed by a road sign

•

Updating the songs to be played on a juke box

•

Updating advertisements to be displayed in a cab

•

Remote accessing a computer, a PLC, an RTU, or other system

•

Monitoring and troubleshooting the status of the device itself without needing to bring it in or go out to it.

A dynamic IP address is suitable for many Internet activities such as web browsing, looking up data on another computer system, for data only being sent out, or for data only being received after an initial request (also called Mobile

Originated). However, if you need to contact the AirLink gateway directly, a device

161

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50 connected to the AirLink gateway, or a host system using your AirLink gateway

(also called Mobile Terminated), a dynamic IP will not give you a reliable address to contact (since it may have changed since the last time it was assigned).

Domain names are often only connected to static IP addresses because of the way most domain name (DNS) servers are set-up. Dynamic DNS servers require notification of IP Address changes so they can update their DNS records and link a dynamic IP address to the correct name.

•

Dynamic IP addresses are granted only when your AirLink gateway is connected and can change each time the gateway reconnects to the network.

•

Static IP addresses are granted the same address every time your AirLink gateway is connected and are not in use when your gateway is not connected.

Since many cellular providers, like wire-based ISPs, do not offer static IP addresses or static address accounts (which can cost a premium as opposed to. dynamic accounts), Sierra Wireless AirLink Solutions developed IP Manager. IP

Manager works with a Dynamic DNS server to receive notification from Sierra

Wireless AirLink gateways to translate the dynamic IP address to a fully qualified domain name. Thus, you can contact your AirLink gateway directly from the

Internet using a domain name.

162

Figure 8-4: ACEmanager: Services > Dynamic DNS

4118967

Services Configuration

Field

Service

Description

Allows you to select a Dynamic DNS Mobile Network Operator.

Options are:

•

Disable (default)

•

dyndns.org

•

noip.org

•

ods.org

•

regfish.com

•

tzo.com

•

IP Manager

3rd party Services

Rev 4 Jun.16

Figure 8-5: ACEmanager: Services > Dynamic DNS Third Party Services

The 3rd party service selected from the Service drop down menu in this example is “dyndns.org.” These same fields will be displayed for all Service selections other than IP Manager and Disable.

163

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Field Description

Service

Allows you to select a Dynamic DNS Mobile Network Operator.

Options are:

•

Disable (default)

•

dyndns.org

•

noip.org

•

ods.org

•

regfish.com

•

tzo.com

•

IP Manager

Dynamic DNS Update

Options are:

•

Only on Change

•

Periodically Update (Not Recommended)

Full Domain Name

Login

The name of a specific AirLink gateway or device

Shows the login name

Password

Update Interval

(hours)

Shows the password in encrypted format

Indicates the time (in hours) between checks for service updates from the selected 3rd party service when periodic is selected.

IP Manager

164

Figure 8-6: ACEmanager: Services > Dynamic DNS > IP Manager

4118967

Rev 4 Jun.16

Services Configuration

Field

Device Name

Domain

Description

The name you want for the device.

If you want to use the current device phone number as part of the

FQDN (for example, 6175551234.eairlink.com) enter #NETPHONE in this field. #NETPHONE is displayed in this field and everywhere else the device name is used, including on the Home > Status page, in SMS messages, in Event reports, as the PPPoE station name, etc.

Using #NETPHONE as the device name is recommended if the account phone number may change and you want the device to continue to use the current phone number as part of the FQDN, or if you are creating a template that will be applied to multiple devices.

To use this feature, you must have IP Manager selected in the Service

field.

The domain name to be used by the device. This is the domain name of the server configured for *IPMANAGER1.

Note: As a service, Sierra Wireless maintains IP Manager servers that can be used with any AirLink gateway. To use one of the free IP

Manager servers, enter eairlink.com in this field.

IP Manager Server 1

(IP Address) /

IP Manager Server 2

(IP Address)

The IP address or domain name of the dynamic DNS server which is running IP Manager.

Note: To use the Sierra Wireless IP Manager server, enter: edns1.eairlink.com (IP Manager Server 1) edns2.eairlink.com (IP Manager Server 2)

IP Manager Server 1

Update /

IP Manager Server 2

Update

IP Manager Server1

Update (mins) /

IP Manager Server2

Update (mins)

IP Manager Server 1

Key /

IP Manager Server 2

Key

Options are:

•

Only on Change

•

Periodic

How often, in minutes, you want the address sent to the IP Manager

User-defined password key used instead of the AirLink secret key when using an IP Manager server other than the one provided by

Sierra Wireless.

Tip:

Some PPPoE connections can use a Service Name to differentiate PPPoE devices.

Use the device name to set a Station Name for the PPPoE connection.

165

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

166

Understanding Domain Names

A domain name is a name of a server or device on the Internet associated with an

IP address. Similar to how the street address of your house or your phone number are ways to contact you, both the IP address and the domain name can be used to contact a server or device on the Internet. While contacting you at your house address or with your phone number employ different methods, using a domain name instead of the IP address uses the same method, just as a word based name is easier for most people to remember than a string of numbers.

Understanding the parts of a domain name can help to understand how IP

Manager works and what you need to be able to configure the device. A fully qualified domain name (FQDN) generally has several parts.

•

Top Level Domain (TLD): The TLD is the ending suffix for a domain name

(.com, .net, .org, etc.)

•

Country Code Top Level Domain (ccTLD): This suffix is often used after the

TLD for most countries except the US (.ca, .uk, .au, etc.)

•

Domain name: This is the name registered with ICANN (Internet Corporation for Assigned Names and Numbers) or the registry for a the country of the ccTLD (i.e., if a domain is part of the .ca TLD, it would be registered with the

Canadian domain registry). A name must be registered before it can be used.

•

Sub-domain or server name: A domain name can have many sub-domain or server names associated with it. Sub-domains need to be registered with the domain, but do not need to be registered with ICANN or any other registry. It is the responsibility of a domain to keep track of its own subs.

car54.mydomain.com

•

.com is the TLD

•

mydomain is the domain (usually noted as mydomain.com since the domain is specific to the TLD)

•

car54 is the subdomain or server name associated with the device, computer, or device registered with mydomain.com

car54.mydomain.com.ca

This would be the same as above, but with the addition of the country code. In this example, the country code (.ca) is for Canada.

Tip:

A URL (Universal Resource Locator) is different from a domain name in that it also provides information on the protocol used by a web browser to contact that address such as

http://www.sierrawireless.com

www.sierrawireless.com is a fully qualified

domain name, but http://, the protocol identifier, is what makes the whole thing a URL.

Dynamic Names

When an IP address is not expected to change, the DNS server can indicate to all queries that the address can be cached and not looked up for a long period of time. Dynamic DNS servers, conversely, have a short caching period for the

4118967

Rev 4 Jun.16

Services Configuration domain information to prevent other Internet sites or queries from using the old information. Since the IP address of a device with a dynamic account can change frequently, if the old information was used (e.g., with a DNS server which indicates the address can be cached for a long period of time) when the IP address changed, the domain would no longer point to the new and correct IP address of the device.

If your AirLink gateway is configured for Dynamic IP when it first connects to the

Internet, it sends an IP change notification to the IP Manager. The IP Manager acknowledges the change and updates the Dynamic DNS server. The new IP address will then be the address for your device’s configured name.

When your device IP address has been updated in IP Manager, it can be contacted by name. If the IP address is needed, use the domain name to determine the IP address.

Note: The fully qualified domain name of your AirLink gateway will be a subdomain of the domain used by the IP Manager server.

SMS Overview

AirLink gateways can:

•

Receive commands via SMS message and send responses, even when the device does not have a data connection (for example, you can provision a device via SMS without having a data connection)

•

Act as an SMS gateway for a device connected to a local interface

Note: To use SMS with your AirLink gateway, you must have an account with SMS enabled.

ACEmanager has four SMS modes. Table 8-2 summarizes the capabilities of

each mode.

Table 8-2: SMS Mode Capabilities

Mode SMS

Command with password

SMS Command without password

Password Only

Control Only

Gateway Only

Yes

Yes*

SMS Gateway

Yes*

167

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Table 8-2: SMS Mode Capabilities

Mode SMS

Command with password

SMS Command without password

SMS Gateway

Control & Gateway

Yes Yes* Yes*

* Provided either:

•

Trusted Phone Number List is disabled.

•

Trusted Phone Number List is enabled and the device’s phone number is in the

Trusted Phone Number List.

For more information on Trusted Phone Number List, see

Inbound SMS Messages on page 181.

Sending SMS Commands to an AirLink

Gateway

Mobile

Network

Remote device

SMS

SMS response

AirLink gateway

Connected device

The format for sending an SMS command varies depending on the mode. See

Table 8-3

for details.

Table 8-3: SMS Command Formats

Mode

Password Only

Control Only (from a number on the

Trusted Phone Number list)

SMS Command Format

PW [Password] [Prefix][Command]

[Prefix][Command] or

PW [Password] [Prefix][Command]

Control Only (from a number not on the

Trusted Phone Number list)

Gateway Only

PW [Password] [Prefix][Command]

Note: Insert a space before and after [Password]; no space between [Prefix] and

[Command].

168 4118967

Rev 4 Jun.16

Services Configuration

Examples:

[Prefix][Command]

“&&&reset”, where:

· &&& is the prefix

If the ALEOS Command Prefix field in ACEmanager (Services > SMS) is blank, the prefix is not required.

· reset is the command

PW [Password] [Prefix][Command]

“PW 1234 &&&reset”, where:

· 1234 is the password

For more information, see SMS Password Security on page 183.

· &&& is the prefix

If the ALEOS Command Prefix field in ACEmanager (Services > SMS) is blank, the prefix is not required.

· reset is the command

For information on sending SMS commands and a list of available commands, see page

419 .

SMS Modes

The following sections provide instructions for configuring each of these modes and sending SMS messages:

•

•

•

•

For a list of available SMS commands, see page 419

. For a list of SMS-related AT commands, see

SMS on page 388.

Password Only

In Password Only mode, you can send SMS commands to a device, provided you use the password. Gateway SMS messaging is not supported in this mode.

Note: In Password Only mode, the password is always required. The Trusted Phone

Number List is not available.

169

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

To configure Password Only mode:

In ACEmanager, go to Services > SMS.

170

Figure 8-7: ACEmanager: Services > SMS > Password Only

In the SMS Mode field, select Password Only.

Enter the desired password in the ALEOS Command Password field or leave the field blank to use the default password.

The password you enter can be any alphanumeric string between 1 and 255 characters long.

For more information see

SMS Password Security on page 183.

If desired, configure SMS Wakeup (see SMS Wakeup on page 180) and

Advanced options (see

SMS > Advanced on page 185).

Click Apply.

For information on the message format, see

Sending SMS Commands to an

AirLink Gateway on page 168.

Control Only

In Control Only mode, you can send SMS commands to an AirLink gateway, but you cannot send non-command (gateway) SMS messages.

You can send an SMS command without a password if:

•

Trusted Phone Number is disabled.

•

Trusted Phone Number is enabled and your phone number is on the Trusted

Phone Number List.

If Trusted Phone Number is enabled and your number is not on the Trusted Phone

Number List, you can still send an SMS command provided you use the password.

4118967

Services Configuration

Configure ALEOS for Control Only mode

In ACEmanager, go to Services > SMS.

Rev 4 Jun.16

Figure 8-8: ACEmanager: Services > SMS > Control Only

In the SMS Mode field, select Control Only.

Enter the desired password in the ALEOS Command Password field or leave the field as is to use the default password.

The password you enter can be any alphanumeric string between 1 and 255 characters long.

For more information see

SMS Password Security on page 183.

Note: If all the SMS commands you send in Control Only mode are from a trusted number, you do not need to include a password when you send the command.

If desired, change the ALEOS Command Prefix or use the default prefix,

&&&.

171

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Note: If you leave the ALEOS Command Prefix field blank, no prefix is required when you send the SMS command. The option to omit the prefix is only available in Control Only mode.

If desired, configure SMS Security options (see

SMS Security on page 181),

SMS Wakeup (see SMS Wakeup on page 180), and Advanced options (see

SMS > Advanced on page 185).

Click Apply.

For information on the message format, see

Sending SMS Commands to an

AirLink Gateway on page 168.

Gateway Only

In Gateway Only mode you can send and receive SMS gateway messages through the AirLink gateway to a local device. SMS messages received by the

AirLink gateway (inbound) are sent on to the configured local device. Messages sent by the local device to a configured port on the AirLink gateway are sent out as SMSs (outbound) to a remote destination. Essentially, the AirLink gateway sends SMS messages between the cellular radio and the connected device.

In Gateway Only mode, you can also send SMS commands provided you include a password. For more information, see

Sending SMS Commands to an AirLink

Gateway on page 168.

To configure ALEOS for Gateway Only mode and format a Gateway message:

In ACEmanager, go to Services > SMS.

172 4118967

Services Configuration

Rev 4 Jun.16

Figure 8-9: ACEmanager: Services > SMS > Gateway Only

In the SMS Mode field, select Gateway Only.

Enter the desired password in the ALEOS Command Password field or leave the field blank to use the default password.

173

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

174

The password you configure can be any alphanumeric string between 1 and

255 characters long.

For more information see

SMS Password Security on page 183.

The SMS destination is the local interface where ALEOS forwards an SMS from the mobile network.

In the SMS destination field, select from the following options:

· Serial—Messages are forwarded to the Serial port on the destination device.

If you want to include the phone number as part of the information sent to the serial port, select Yes in the Include Phone Number on Serial field.

Proceed to step 13.

· IP—Messages are sent using UDP over IP to a designated LAN device.

Proceed to step 5.

Local Device Interface Configuration (Applies to inbound [to the local device] gateway messages when IP is the SMS destination and outbound

[from the local device])

Inbound

Enter the Local Host IP address.

This is the IP address of the LAN device that is used as the destination for all incoming Gateway messages.

Enter the Local Host Port.

This is the UDP port the destination device listens to for incoming messages.

Outbound

Enter the ALEOS port.

This is the UDP port on which the AirLink gateway listens for outbound Gateway messages sent from any local device.

Message Format Configuration (Only applies if you selected IP in the SMS destination field)

In the Start field, enter the start of message delimiter, or use the default

(<<<).

In the Field Delimiter field, enter the delimiter to be used between fields in the

SMS message, or use the default (,).

10. In the End field, enter the end of message delimiter, or use the default (>>>).

11. In the ACK field, enter the desired acknowledgment message, or use the default (ACK). The acknowledgment is sent to the device as a UDP packet on the same port as the device used to send the message.

ALEOS provides a message acknowledgment for every SMS message when it is passed to the radio. If ALEOS does not send an ACK, wait for 30 seconds, and then retry.

Security

12. If desired, configure SMS Security options (see

SMS Security on page 181),

SMS Wakeup (see SMS Wakeup on page 180), and Advanced options (see

SMS > Advanced on page 185).

13. Click Apply.

4118967

Rev 4 Jun.16

Services Configuration

If you are using IP as the destination and you have changed the IPs or port numbers, reboot the device.

For information on the message format for an SMS Command, see

Sending SMS

Commands to an AirLink Gateway on page 168.

Sending a gateway message from a local IP device to a remote destination

Mobile

Network

AirLink gateway unpacks UDP packet and sends SMS to

Remote device

SMS

AirLink gateway

Ethernet or

USB Ethernet connected device

SMS message in UDP packet

The AirLink gateway acts as a gateway to send SMS messages from an IP connected device using AirLink SMS Protocol. The IP device sends a UDP packet to the AirLink gateway, which then sends the SMS to its destination.

Note: Outgoing SMS messages are limited to 140 characters.

To use AirLink SMS Protocol to send an SMS message from a connected device:

Begin with the start field.

Follow with the destination phone number. This number must be in the same format as the phone numbers in the Trusted Phone Number List.

Note: There is no space between the start number and the destination phone number or between any delimiter and the data fields.

Add the field delimiter.

Add the data type for the message:

For: Enter:

ASCII

8-bit

ASCII

8BIT

Unicode UCS-2

Data types are case sensitive.

Add another field delimiter.

Add the number of ASCII characters in your original message (before it is converted to ASCII hex format).

Add another field delimiter.

175

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

176

Add the message to be sent in ASCII hex format. ASCII is case sensitive. Do not use any punctuation, such as a colon, or characters between hex pairs.

Finish with the end field.

Example: You want to send the following message: “Test message” to phone number (510) 555-4200. To use this feature, convert the message to hex:54657374206d657373616765. Then format the message as follows:

<<<15105554200,ASCII,12,54657374206d657373616765>>> where:

· “<<<” is the start delimiter

· “15105554200” is the phone number

· “,” is the delimiter between fields

· “ASCII” is the data type

· “12” is the number of characters in the original message (before it is converted to ASCII hex format)

· “54657374206d657373616765” is the message itself

· “>>>” is the end delimiter

10. Send the UDP packet to the configured ALEOS port.

After your message is sent, you receive an ACK message in the format ACK

Field acknowledgment Code ACK Field. For example, if your message was successfully queued to be sent, you receive the message: ACK0ACK.

If you receive an error message, see

SMS on page 440 for details.

Note: You can also use AT*SMSM2M to send an SMS message to the remote device. For

more information, see SMSM2M on page 186.

Sending a gateway message to the connected device using IP address and port as the SMS destination

Mobile

Network

AirLink gateway encapsulates

SMS into a UDP packet and sends it to the connected device.

Remote device

SMS

AirLink gateway

Ethernet or

USB Ethernet

Connected device

SMS message in UDP packet

Messages from a remote device can be sent to the AirLink gateway. The AirLink gateway encapsulates the message in a UDP packet using AirLink SMS Protocol, and sends it to the configured Local Host IP and Local Host Port on the connected device.

Message example:

Example:

1. An SMS is sent from phone number (640) 555-4200 to the device: “Test message”

4118967

Rev 4 Jun.16

Services Configuration

2. The AirLink gateway receives the SMS and determines it is a gateway message.

3. The AirLink gateway converts the message into a UDP packet using the AirLink

SMS Protocol and sends it to the configured Local Host IP at Local Host Port.

The message as follows:

<<<16045554200,ASCII,12,54657374206d657373616765>>> where:

· “<<<” is the start delimiter

· “16045554200” is the phone number

· “,” is the delimiter between fields

· “ASCII” is the message type*

· “12” is the number of characters in the message

· “54657374206d657373616765” is the message itself

· “>>>” is the end delimiter

* In this example the message is in ASCII, but it could also be in 8-bit or Unicode format:

For: Enter:

ASCII ASCII

8BIT

8-bit

Unicode UCS-2

Data types are case sensitive.

Sending a gateway message to the connected device using Serial or USB Serial as the SMS destination

Mobile

Network

AirLink gateway sends the body of the SMS message to the serial port on the connected device as ASCII text. If the Include Phone

Number on Serial field is set to Yes, it adds the phone number to the beginning of the message.

Remote device

SMS

AirLink gateway

Serial or USB Serial

Connected device

ASCII text

A message can be sent from a remote device to the AirLink gateway. The AirLink gateway sends the body of the message in ASCII text to the connected device. If the Include Phone Number on Serial field is set to Yes, the AirLink gateway prepends the phone number to the message.

177

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Control and Gateway

In Control and Gateway mode you can do both—send commands to the device and send gateway messages to the connected device. When the Trusted Phone

Number List is enabled, all SMS messages from trusted devices that do not begin with the password indicator (PW) or the command prefix are sent to the connected device as a gateway message.

For more information, see

Trusted Phone Number on page 182.

Configure ALEOS for Control and Gateway mode

In ACEmanager, go to Services > SMS.

Select Control and Gateway.

178 4118967

Services Configuration

Rev 4 Jun.16

Figure 8-10: ACEmanager: SMS > Control and Gateway

For more information, see

Control Only

on page 170 and Gateway Only on page 172.

179

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

SMS Wakeup

This feature is supported on International AirLink gateways on the Vodafone network.

When the AirLink gateway is in Connect on traffic mode (for details, see

Always on connection on page 62), you can configure the AirLink gateway to also initiate

a mobile network data connection on receipt of an SMS. After the connection is established, it remains active until the configured timeout expires. The mobile network data connection closes after the specified timeout period. Outgoing traffic sent after the timer is triggered does not reset the timer.

To configure SMS Wakeup:

In ACEmanager go to WAN/Cellular > Advanced and ensure that the Always on connection field is set to Disabled - Connect on traffic.

Go to Services > SMS.

180

Figure 8-11: ACEmanager: Services > SMS

In the SMS Wakeup Trigger field, select the type of SMS that should wake up the device. The options are:

· Feature Disabled

· Any Class 0 message

· Class 0 Wake Command

· Any SMS message

· Wake Command

Note: “Class 0 Wake Command” and “Wake Command” are SMS commands.

Click Apply.

4118967

Rev 4 Jun.16

Services Configuration

In the Connection timeout (minutes) field, enter the number of minutes the mobile network data connection remains active after SMS Wakeup Trigger is received. Accepted values for this field are 2–65535. The default value is 2.

You can also set the Connection timeout using an AT command. For more information, see

*SMSWUPTOUT on page 389.

If you selected Class 0 Wake Command or Wake Command in step 3, you

can specify the SMS command name in the Wake Command field or use the default value, WAKEUP. Sending this SMS to the device will wake it up.

Example: &&&WAKEUP (&&& is the SMS command prefix.)

Click Apply.

SMS Security

Inbound SMS Messages

Incoming SMS messages are received as UDP packets, and forwarded to the local device IP address and port. The UDP packets are in the same format as sent messages.

When Trusted Phone Number security is enabled, incoming messages coming from the phone numbers in the Trusted Phone Number list are the only ones for which commands will be performed (relay, response etc.) or gateway messages forwarded. Incoming messages from all other phone numbers will be ignored.

Commands sent to the device with the correct password are always treated as coming from a trusted number.

All non-alphanumeric characters except a space will be replaced by a dot in

ACEmanager.

181

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Figure 8-12: ACEmanager: Services > SMS > Security

Field Description

SMS Security - Inbound SMS Messages

Trusted Phone

Number

Allows you to Enable or Disable a trusted phone number

Last Incoming Phone

Number

Last Incoming

Message

Trusted Phone

Number List

The last inbound phone number is displayed here. This will only be erased with a reset to defaults.

The last incoming message is the last inbound SMS from the phone number. This will only be erased with a reset to defaults.

Trusted phone numbers are listed here

Trusted Phone Number

Follow the instructions below to add a Trusted Phone Number on the SMS page.

Send an SMS command to the device, and hit Refresh. If Trusted Phone

Number is enabled, and the phone number is not in the Trusted Phone

Number List, no action is performed on the message.

182 4118967

Rev 4 Jun.16

Services Configuration

Once you have the Last Incoming Phone Number that shows up on the SMS window in ACEmanager, note the exact phone number displayed.

Click Add More to add the Trusted Phone Number. The Last Phone Number will continue to display. Additions to the Trusted Phone Number become effective immediately. You do not need to reboot the device.

Note: The Trusted Phone number can be up to 15 characters long and must be comprised of numbers only.

Note: Phone Numbers (both trusted and not trusted) will be displayed in the Last Incoming

Phone Number field.

Enter the Last Incoming Phone Number as the Trusted Phone Number.

Click Apply.

Note: Do not enter any extra digits, and use the Last Incoming display as a guide to type the phone number. Use “1” only if it is used in the beginning of the Last Incoming Phone

Number.

With Trusted Phone Number enabled, only those SMS messages from Trusted

Phone Numbers will receive responses to commands or messages acted on as applicable.

SMS Password Security

The SMS Password feature enables you to use a password to send a command at any time to the device. Even if Trusted Phone Number is enabled, you can send an SMS command from a non-trusted number, provided you include the password.

A default SMS password is generated from the last four characters of the SIM ID

(for all SIM-based devices) or the ESN (for devices without a SIM, such those using EV-DO), or you can configure your own SMS password.

Tip:

If you do not know the SIM ID or ESN number you can find it in ACEmanager

(Status > WAN/Cellular).

Note: The SMS password is not the same as the ALEOS password used to access

ACEmanager or Telnet/SSH.

To configure the SMS password:

Go to Services > SMS > SMS Mode.

183

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

184

Figure 8-13: ACEmanager: Services > SMS > Password

Enter the desired SMS password in the ALEOS Command Password field.

The password can be any alphanumeric string with a length between 1 and

255 characters.

Click Apply.

Note:

•

The SMS password is not displayed in plain text in ACEmanager. If you want to query

it, use the AT command. See *SMS_PASSWORD on page 388.

•

The SMS password is not cleared by a configuration reset.

•

If an SMS command is sent with the wrong SMS password, the device replies with a

“Wrong Password” message, and the command is dropped.

Using the Default SMS Password

You can use the default SMS password (last 4 characters of either the SIM ID number for SIM-based devices, or the ESN for devices without a SIM) with no prior configuration.

Note: The default password:

•

Works with all SMS commands

•

Is not displayed in ACEmanager (If the ALEOS Command Password field is blank, the default password is used.)

•

Is overridden by a user-defined password

•

Changes if the SIM is changed, if no user-defined password is configured

4118967

SMS > Advanced

Services Configuration

Figure 8-14: ACEmanager: Services > SMS > Advanced

Field

SMS Address Type

SMS Address

Numbering Plan

Description

For most networks, use the default setting (International). The address type of the phone number used to send outgoing messages and command responses. Options are:

•

International (default)

•

National

•

Network Specific

•

Subscriber

•

Abbreviated

For most networks, use the default setting (ISDN/Telephone). The address numbering plan of the phone number used to send outgoing messages and command responses. Options are:

•

Unknown

•

ISDN/Telephone (default)

•

Date Numbering

•

Telex

•

National

•

Private

•

ERMES

Rev 4 Jun.16

185

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Field

AT+CGSMS

Quick Test

Destination

Description

Allows you to choose the technology used to send SMS messages. For most networks, use the default setting (Do nothing). Options are:

•

Do nothing (default)

•

Set AT+CGSMS=0—GPRS

•

Set AT+CGSMS=1—Circuit switched

•

Set AT+CGSMS=2—GPRS Preferred (Uses circuit switched if GPRS is not available)

•

Set AT+CGSMS=3—Circuit Switched Preferred (Uses GPRS if circuit switched is not available)

Note: If your gateway is able to receive SMS messages, but is unable to send them, try changing this field to Set AT+CGSMS=1.

Note: This field does not appear on CDMA/EV-DO devices or on LTE devices that fallback to CDMA/EV-DO.

Allows you to send a test message to the destination entered in the Quick Test Destination field.

Enter the phone number to use for the test message. Click Apply before clicking the Quick

Test button.

This field is cleared on reboot.

SMSM2M

SMS messages can be sent from the serial command interface. Enter

AT*SMSM2M=”[phone] [message]”. The phone number needs to be in the same format as numbers entered in the Trusted Phone Number List.

The message must not exceed 140 characters. To send several messages back to back, you must wait for the OK before sending the next message.

186 4118967

Rev 4 Jun.16

Command

*SMSM2M

*SMSM2M_8

*SMSM2M_u

Services Configuration

Description

*SMSM2M is the command for ASCII text.

*SMSM2M_8 is the command for 8-bit data.

*SMSM2M_u is the command for unicode.

Format:

*smsm2m=”[phone][ascii message]”

*smsm2m_8=”[phone][hex message]”

*smsm2m_u=”[phone][hex message]”

•

The phone number can only consist of numbers (NO spaces or other characters). The phone number should be as it appears in the Last

Incoming Phone Number field.

Example 1 (US): 14085551212 (including leading 1 and area code)

Example 2 (US): 4085551212 (ignore leading 1, include area code)

Example 3 (UK): 447786111717 (remove leading 0 and add country code)

Command Examples:

*smsm2m=”18005551212 THIS IS A TEST” sends in ASCII.

*smsm2m_8="17604053757 5448495320495320412054455354" sends the message “THIS IS A TEST” as 8-bit data.

*smsm2m_u="17604053757

000102030405060708090a0b0c0d0e0f808182838485868788898A8b8c8d8e

8f" sends the bytes:

00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f

80 81 82 83 84 85 86 87 88 89 8a 8b 8c 8d 8e 8f

Note: Not all cellular carriers support 8-bit or unicode SMS messages.

187

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Telnet/SSH

Use the Telnet or SSH protocol to connect to any AirLink gateway and send AT commands.

A secure mechanism to connect remote clients is a requirement for many users.

In ACEmanager, Secure Shell (SSH) is supported to ensure confidentiality of the information and make the communication less susceptible to snooping and man-in-the-middle attacks. SSH also provides for mutual authentication of the data connection.

Figure 8-15: ACEmanager: Services >Telnet/SSH

Field

Remote Login Server

Mode

Default Telnet User

Description

Select either Telnet (default) or SSH mode.

Select a default Telnet User name

Options are:

•

None—When you log into a Telnet session, you are prompted for a user name and password.

•

user—When you log into a Telnet session, you are prompted only for a password.

Telnet uses the default user name (user).

Note: The default user name is only for Telnet; not SSH.

188 4118967

Services Configuration

Field

Remote Login Server

Telnet/SSH Port

Description

Sets or queries the port used for the AT Telnet/SSH server.

Default: 2332

Tip:

Many networks have the ports below 1024 blocked. We recommend that you use a higher numbered port.

Remote Login Server

Telnet/SSH Port

Timeout (mins)

Maximum Login

Attempts

Telnet/SSH Echo

Make SSH Keys

SSH Status

Telnet/SSH port inactivity time out.

Default: 2 (minutes)

Sets the maximum number of login attempts.

Default: 6

Enable (default) or disable AT command echo mode.

Creates keys for SSH session applications

Provides the status of the SSH session

Note: When you are connected to SSH locally, you cannot have OTA SSH connected.

Email (SMTP)

For some functions, the device needs to be able to send email. Since it does not have an embedded email server, you need to specify the settings for a relay server for the device to use.

A reboot is required after configuring the email settings.

Note: The SMTP function will only work with a mail server that will allow relay email from the ALEOS device’s Net IP.

Rev 4 Jun.16

189

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Figure 8-16: ACEmanager: Services > Email (SMTP)

Field

General

SMTP Server

Description

Port

Specify the IP address or Fully Qualified Domain Name (FQDN) of the SMTP server to use.

•

d.d.d.d = IP Address

•

name = domain name (maximum: 40 characters)

Server port (Default is 25.)

Encryption method

SSL

StartTLS

465

587

Default port

From Email Address

Sets the email address from which the SMTP message is being sent.

•

email = email address (maximum: 30 characters)

User Name (optional)

Specifies the username to use when authenticating with the server

Password (optional)

Sets the password to use when authenticating the email account (*SMTPFROM) with the server (*SMTPADDR).

•

pw = password

Note: The email server used for the relay may require a user name or password.

190 4118967

Services Configuration

Field

Message Subject

Quick Test

Description

Allows configuration of the default Subject to use if one is not specified in the message by providing a “Subject: xxx” line as the initial message line.

•

subject = message subject

After completing the other fields on this screen, click the Quick Test button to send a test

email. The status of the test appears in the Test status field.

Enter the email address you want the test email sent to.

Quick Test

Destination

Test status

SSL/TLS

After you press the Quick Test button, the status of the email test appears in this field.

Encryption

Choose the encryption method:

•

None—No encryption is used (default)

•

SSL—Use a secure connection directly

•

StartTLS—Transforms an non-secure connection to a secure one

For SSL and StartTLS default ports, see

Port on page 190.

Verify Peer Certificate

Choose whether or not to use a peer certificate

Disable—No certificate is used (default)

Enable—Verifies that the server name used for the connection matches the name and alternative names in the certificate loaded using the

Load Trusted CA Certificate field.

Load Trusted CA

Certificate

To load a certificate:

Click the Load Trusted CA Certificate button.

Click browse and navigate to the certificate you want to load.

Click Upload File to Device.

Note: Because the starting and expiration dates of the certificate are checked, the date used by the device must be correct. Sierra Wireless strongly recommends that you enable

Network Time Protocol (NTP) on the Services > Time (SNTP) tab.

Trusted CA Certificate

Name

The name of the loaded certificate appears in this field.

Rev 4 Jun.16

191

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Management (SNMP)

The Simple Network Management Protocol (SNMP) is designed to allow for remote management and monitoring of a variety of devices from a central location. It is generally used to monitor conditions that may require attention.

The SNMP management system is composed of:

•

One or more managers (administrative computers)

•

SNMP-compliant devices (such as your AirLink gateway, a router, a UPS, a web server, a file server, or other computer equipment)

•

An agent (data collection software running on the SNMP-compliant devices)

•

A Network Management System (NMS) that monitors all the agents on a specific network.

The agent stores information about the device in a Management Information Base

(MIB). The manager can send messages to this database to configure and query the status of the device. In addition, the agent running on the device can send traps (unsolicited messages) to the manager on startup, on status change, or when an error condition occurs.

AirLink gateways supports SNMPv2c and SNMPv3 and you can configure them as SNMP agents.

Authentication ensures SNMP messages coming from the AirLink gateway have not been modified and the device cannot be queried by unauthorized users.

SNMPv3 uses a User-Based Security Model (USM) to authenticate and, if desired or supported, message encryption. USM uses a user name and password specific to each device.

A reboot is required after configuring SNMP.

192 4118967

SNMPv2

Services Configuration

Figure 8-17: ACEmanager: Services > Management (SNMP) Version 2

Field

SNMP Configuration

Enable SNMP

SNMP Version

SNMP Port

SNMP Contact

SNMP Name

SNMP Location

Description

Allows you to enable/disable SNMP

Default: Disable

Allows you to select either SNMP protocol Version 2 (default) or Version 3 communications.

Controls which port the SNMP Agent listens on:

•

1–65535

•

Default is 161.

This is a personal identifier of the contact person you want to address queries to.

This is a customer defined field.

This is the name of the device you want to refer to.

This is a customer defined field.

Location of where your device is stored

Enter a meaningful description of where the AirLink gateway is located.

Rev 4 Jun.16

193

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Field Description

Read Only SNMP User

Community Name

The community name is a text string that acts as a password. It is used to authenticate messages that are sent between the management station and the device.

Default is public.

Read/Write SNMP User

Community Name

The community name is a text string that acts as a password. It is used to authenticate messages that are sent between the management station and the device.

Default is private.

TRAP Server User

TRAP Server IP/FQDN

Identifies the IP address or fully qualified domain name (FQDN) of the trap server that the

AirLink gateway sends SNMP traps to

TRAP Server Port

Identifies the specific port the trap server is on

•

1–65535

•

Default is 162.

Community Name

The community name is a text string that acts as a password. It is used to authenticate messages that are sent between the management station and the device.

There is no default value.

194 4118967

SNMPv3

Services Configuration

Figure 8-18: ACEmanager: Management (SNMP) Version 3

Field

SNMP Configuration

Enable SNMP

Description

SNMP Version

SNMP Port

SNMP Contact

SNMP Name

SNMP Location

Allows you to enable/disable SNMP

Default is Disable.

Allows you to select either SNMP protocol Version 2 (default) or Version 3 communications.

Controls which port the SNMP Agent listens on:

•

1 – 65535

•

Default is 161.

This is a personal identifier of the contact person you want to address queries to. This is a customer defined field.

This is the name of the device you want to refer to. This is a customer defined field.

Location of where your device is stored. This is a customer defined field.

Rev 4 Jun.16

195

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Field

Read Only SNMP

User Name

Security Level

Authentication Type

Authentication Key

Privacy Type

Description

Allows these SNMP users to view, but not change the network configuration

Security types available: None, Authentication Only, and Authentication and Privacy.

Authentication types available: MD5 or SHA

Note: This field is only available when you select either Authentication and Privacy, or

Authentication Only in the Security Level field.

This key authenticates SNMP requests for SNMPv3.

•

Minimum length: 8 ASCII characters

•

Maximum length: 255 ASCII characters

Example: My Key_1234

Note: This field is only available when you select either Authentication and Privacy, or

Authentication Only in the Security Level field.

Privacy types available: AES or DES

Note: This field is only available when you select Authentication and Privacy in the

Security Level field.

Privacy Key

This key ensures the confidentiality of SNMP messages via encryption

•

Minimum length: 8 ASCII characters

•

Maximum length: 255 ASCII characters

Example: My Key_56789

Note: This field is only available when you select Authentication and Privacy in the

Security Level field.

Read/Write SNMP

For a description of the Read/Write SNMP fields, see Read Only SNMP on page 196.

TRAP Server User

TRAP Server IP/FQDN

Identifies the IP address or fully qualified domain name (FQDN) of the trap server that the

AirLink gateway sends SNMP traps to

TRAP Server Port

Identifies the specific port the trap server is on

•

1 – 65535

•

Default is 162.

196 4118967

Services Configuration

Field

Engine ID

User Name

Security Level

Authentication Type

Authentication Key

Privacy Type

Privacy Key

Description

The Engine ID is a mandatory field that uniquely identifies the SNMPv3 agent in the device to the server.

The Engine ID is 5–32 octets long (1 octet is 2 hex characters). That is:

•

Minimum length: 10 hex characters

•

Maximum length: 64 hex characters

Create the engine ID by entering hex characters only, with no leading 0x. For example,

ABCDEF1020

See User Name on page 196.

See Security Level on page 196.

See Authentication Type on page 196.

See Authentication Key on page 196.

See Privacy Type on page 196.

See Privacy Key on page 197.

Time (SNTP)

The device can be configured to synchronize its internal clock with a time server on the Internet using the Simple Network Time Protocol. Normally your device will synchronize with the mobile network or GPS.

Rev 4 Jun.16

Figure 8-19: ACEmanager: Services > Time (SNTP)

197

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Field Description

Enable time update

Enables daily SNTP update of the system time.

Default: Disable

SNTP Server Address

SNTP Server IP address, or fully qualified domain name, to use if *SNTP=1. If blank, time.nist.gov is used.

•

d.d.d.d=IP address

•

name=domain name

Authentication

ALEOS supports ACEmanager login using secure LDAP, RADIUS, and TACACS+ authentication schemes. This enables enterprise IT managers to centrally manage access to AirLink gateways and produce an audit trail showing which users logged into specific devices and when.

Note the following:

•

You can configure any or all of these schemes at the same time. When more than one scheme is configured, the authentication is successful if at least one of the schemes authenticates the user.

•

Successful authentication can take time. For example, if you have all three authentication schemes enabled, ALEOS first attempts to reach the LDAP server. If it is unable to reach the LDAP server in the configured timeout period, it abandons the attempt and tries to reach the RADIUS server. If that server is unreachable after the timeout period, it then tries to reach the

TACACS+ server. If none of the servers are reachable in the configured timeout periods, ALEOS falls back to ACEmanager user name and password authentication.

•

LDAP, RADIUS, and TACACS+ provide authentication (checks the user’s credentials) but do not check authorization (account expiration date, user rights, etc.) All users authenticated using the LDAP, RADIUS, and TACACS+ servers have administrative rights (i.e. a user account, not a viewer account) and can modify the AirLink gateway settings. Ensure that LDAP, RADIUS, and

TACACS+ users are authorized to modify device settings.

•

LDAP, RADIUS, and TACACS+ are supported for ACEmanager logins, but are not supported by other AirLink gateway services such as Telnet, SSH,

PPPoE, etc.

For instructions on configuring these authentication schemes, see:

•

LDAP Authentication on page 199

•

RADIUS Authentication on page 200

•

TACACS+ Authentication on page 201

198 4118967

Services Configuration

LDAP Authentication

Lightweight Directory Access Protocol (LDAP) is a network protocol for accessing and manipulating information stored in a directory. It is suitable for using with information that must be easily available and accessible, and does not change frequently. AirLink gateways support LDAP version 3.

To configure LDAP:

Go to Services > Authentication.

In the LDPA Client field, select Enable.

Rev 4 Jun.16

Figure 8-20: ACEmanager: Services > Authentication > LDAP

Enter:

· The LDAP server IP address or resolvable domain name

· The Port number (default is TCP port 389)

Ensure that the LSDAP server IP address/port is reachable not only from outside the company, but also from inside the mobile network your gateway is on.

You can use a utility such as netcat to test this. If netcat is available, try: nc -z <IP> <port>; echo $?

0 means success; 1 means failure.

199

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Configure the other fields as described in the following table.

Field

Timeout (seconds)

Description

The time limit for the server to respond

•

1–60 seconds

Default is 30 seconds.

Note: If the server does not respond during the timeout (no route to host, server down, network too slow etc.), the authentication fails and the next enabled authentication mechanism checks the credentials.

Encryption

Base DN

Bind DN

Bind DN User

Bind on Password

Select the encryption type

Options are:

•

None

•

SSL—Secure Sockets Layer protocol —Non-standard legacy (pre-LDAPv3) encryption type

•

StartTLS—Secure mechanism integrated into the

LDAPv3 protocol (default)

The Base DN is the path in the LDAP tree to the list of users

(example shown is dc=sierrawireless,dc=com). This is where the LDAP protocol searches for a matching user to authenticate.

Choose how the LDAP search is done

Options are:

•

Anonymous—Bind anonymously (default)

•

Explicit—Use a specific account to bind with

This field only appears if you selected Explicit in the Bind DN field

The full path of the user authorized to perform requests in the

LDAP database (example shown is cn=admin,dc=sierrawireless,dc=com)

This field only appears if you selected Explicit in the Bind DN field

User password to bind with

Click Apply.

RADIUS Authentication

Remote Authentication Dial In User Service (RADIUS) uses UDP and checks authentication credentials, using a shared key.

To configure RADIUS:

Go to Services > Authentication.

In the RADIUS Client field, select Enable.

200 4118967

Services Configuration

Rev 4 Jun.16

Figure 8-21: ACEmanager: Services > Authentication > RADIUS

Configure the other fields as described in the following table.

Field

RADIUS Server

Port

Timeout (seconds)

Description

RADIUS server IP address or resolvable domain name

By default, RADIUS uses UDP port 1812

The time limit for the server to respond

•

1–60 seconds

Default is 30 seconds.

Secret Shared secret for configured server

Click Apply.

TACACS+ Authentication

Terminal Access Controller Access-Control System Plus (TACACS+) uses TCP protocol and encrypts the entire packet, except the header.

To configure TACACS+:

Go to Services > Authentication.

In the TACACS+ Client field, select Enable.

201

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Enter:

· The TACACS+ server IP address or resolvable domain name

· The Port number (default is TCP port 49)

Ensure that the TACACS+ server IP address/port is reachable not only from outside the company, but also from inside the mobile network your gateway is on.

You can use a utility such as netcat to test this. If netcat is available try: nc -z <IP> <port>; echo $?

202

Figure 8-22: ACEmanager: Services > Authentication > TACACS+

Configure the other fields as described in the following table.

Field

Timeout (seconds)

Description

The time limit for the server to respond

•

1–60 seconds

Default is 30 seconds.

4118967

Services Configuration

Field

Authentication service

Description

The type of bind used for authentication

Options are:

•

PAP—Password Authentication Protocol (default)

•

CHAP— Challenge Handshake Authentication Protocol

The stronger of the two protocols. Recommended, provided it is supported by all the client devices.

•

Shared secret for configured server Secret

Click Apply.

Device Status Screen

The Device Status Screen feature, when enabled, allows you to add GPS and network status parameters to the ACEmanager Login screen. Once enabled, subsequent logins to ACEmanager display whatever status parameters have been previously checked on the Device Status Screen.

Figure 8-23: ACEmanager: Services > Device Status Screen

Field

Enable Device Status on Login Screen

Status to display

Description

Enables device status parameters on the login screen

Options are: Disable or Enable (default)

Allows you to display specific GPS and network status parameters on the login screen

Rev 4 Jun.16

203

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

204 4118967

Rev 4 Jun.16

9: GPS Configuration

Most AirLink devices are equipped with a Global Positioning System receiver (GPS) to ascertain its position and track the movements of a vehicle or other devices which move. The AirLink gateway relays the information of its location as well as other data for use with tracking applications.

Note: GPS is disabled by default in the AirLink RV50. To enable it, see

Enable GPS on page 207.

GPS Overview

The Global Positioning System (GPS) is a satellite navigation system used for determining a location and providing a highly accurate time reference.

GPS consists of a “constellation” of 32 satellites in 6 orbital planes.

Each satellite circles the Earth twice every day at an altitude of

20,278 kilometers (12,600 miles). Each satellite is equipped with an atomic clock and constantly broadcasts the time, according to its own clock, along with administrative information including the orbital elements of its motion, as determined by ground-based observatories.

A GPS receiver, such as the AirLink gateway, requires signals from four or more satellites and performs Time Difference of Arrival

(TDoA) calculations in order to determine its own latitude, longitude, and elevation.

The GPS data can then be transmitted to a server with a tracking application to compile information about location, movement rates, and other pertinent data.

Note: Depending on the location of the satellites in relation to the device’s location and how many signals are being received, the AirLink gateway may encounter “GPS drift”, a phenomenon whereby a stationary device is reported as moving by the GPS system. This “drift” is within the location tolerances of the GPS system, but the device may appear to be moving, based on continuous GPS calculations.

Common Uses for GPS

•

Driver navigation—The AirLink gateway provides real time GPS data via the serial or Ethernet port to a local application, including applications that provide mapping and navigation support.

205

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

•

Automatic Vehicle Location (AVL)—The AirLink gateway provides real time

GPS data to the server that tracks the location and other variables of the vehicle or asset.

ALEOS Supported GPS Report Protocols

•

Remote Access Protocol (RAP)

RAP is a proprietary binary message format developed and maintained by

Sierra Wireless and used by many 3rd party applications. Because it is designed and maintained by Sierra Wireless, RAP supports more ALEOS features than other GPS protocols. It is a low-byte-usage protocol that can be used to develop low cost AVL solutions.

The RAP messages are in hex and are referred to by their message ID.

Reports can include GPS data alone, as well as GPS data with the date and time, radio frequency data, radio status information, and I/O state changes, and power state changes. For an example, see

GPS RAP Report Sequence

Example on page 220. For more information, contact your Sierra Wireless

Sales representative for information on how to obtain a copy of the RAP Protocol Guide.

•

National Marine Electronics Association (NMEA

)

NMEA is an ASCII protocol used by many GPS tracking applications.

•

Trimble

ASCII Interface Protocol (TAIP)

TAIP is a digital communication interface based on printable ASCII characters over a serial data link. TAIP was designed specifically for vehicle tracking applications but has become common in a number of other applications, such as data terminals and portable computers, because of its ease of use.

•

Xora

Protocol specific to Xora asset management and tracking applications

Before Configuring GPS

To decide what configuration you need for your AirLink gateway, there are some fundamental considerations you should determine:

•

Protocol—What is the GPS protocol used by your tracking application and what type of reports will you need? (See

GPS Report Type on page 215.)

•

Dynamic IP Address—Does your device have a dynamic IP address and you need to track the specific asset? (See

Device ID in Local Reports on page 227.) You can also associate your device with a dynamic DNS configu-

ration. (See

Dynamic DNS on page 161.)

•

Server locationand type of connection—Will you be using a local server, a remote server, or both? Will you need a serial or local IP connection?

•

Multiple GPS servers—Will you need to have GPS data sent to more than one GPS server?

206 4118967

Rev 4 Jun.16

GPS Configuration

Server Location?

Remote

See

Servers 1 to 4 on page 210.

Serial connection

See Local/Streaming on page 222.

Figure 9-1: Server location and connection type

Local

Streaming report to local IP connection

See

Local/Streaming—Local IP Report on

page 224 or Servers 1 to 4 on page 210.

Note: Most Global settings (described on page 208

) apply to remote and local servers. All

GPS configuration changes go into effect immediately. No reboot of the AirLink gateway is necessary. After you configure any settings there is a short pause in receiving GPS reports while the device is re-initialized with the new configuration.

Enable GPS

To enable GPS:

In ACEmanager, go to GPS.

Figure 9-2: ACEmanager: GPS

In the GPS Service field, select Enable.

Click Apply.

Reboot the gateway.

207

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Global Settings

Note:

Most of the Global settings apply to all GPS Server and Local reports.

These screens are only visible when GPS is enabled. See

GPS Service on page 208.

Figure 9-3: ACEmanager: GPS > Global Settings

Table 9-1: GPS: Global Settings

Field Description

GPS Settings

GPS Service

Sierra Wireless recommends that you disable GPS if you are not using GPS reporting.

Options are:

•

Enable (default)

•

Disable

The change takes effect after you reboot the gateway.

208 4118967

GPS Configuration

Table 9-1: GPS: Global Settings (Continued)

Field Description

General — These fields only appear is GPS Service is enabled.

Odometer Value

(meters)

The odometer value increments based on the GPS distance traveled. You can include this

value in RAP GPS reports. (See

You can set the odometer value to an initial value. Maximum value is 4 294 967 295 meters

(4,294,967 kilometers or 2,668,769 miles).

Default: 0

GPS Report Type on page 215).

Note: The RAP report displays the odometer value in 100s of meters.

TAIP ID

Send SnF Buffer immediately on input

Use Device ID in

Location Reports

You can also use an AT Command to set this value. For more information, see

*PPODOMVAL on page 398.

The four character alphanumeric ID used in all TAIP reports

You can also use an AT Command to set this value. For more information, see *PPTAIPID on page 399.

If this feature is enabled, any pending stored reports are sent if the I/O input changes, a stationary vehicle is moved, or a maximum speed is exceeded, provided those events are enabled on the GPS > Server > Events screen. Options are:

•

Disable (default)

•

Enable

You can also use an AT Command to set this value. For more information, see

*PPFLUSHONEVT on page 395.

Allows use of the IMEI/ESN or phone number in RAP reports configured for Servers 1–4 to identify a device/vehicle. Options are:

•

None (default)

•

Phone Number

•

ESN/IMEI

You can also use an AT Command to set this value. For more information, see *PPDEVID on page 395.

Tip:

Including the device ID is especially useful when your devices have dynamic IP addresses.

Note: The device ID in RAP reports is in hex, not plain text.

Note: This option does not apply to Local IP reports. If you want the device ID included in

local IP GPS reports, see Device ID in Local Reports on page 227.

Note: If you want this Device ID included in the TCP PAD connections, enable the Include

Device ID on TCP Connect field on the Serial screen (Serial > Port Configuration > TCP).

See Port Configuration on page 247.

Rev 4 Jun.16

209

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Table 9-1: GPS: Global Settings (Continued)

Field Description

Advanced — These fields only appear is GPS Service is enabled.

TCP GPS Port

You can obtain a single location snapshot from the device via a TCP session using the

AirLink gateway’s IP address and the device port configured in this field.

•

1–65535 (default 9494)

•

0 = Disable

You can also use an AT Command to set this value. For more information, see

*PPTCPPOLL on page 399.

Note: Access is restricted to the IP address defined for server 1. (See Report Server IP

Address on page 216.)

GPS Fix Mode

Heading Sensitivity

Specifies the GPS fix mode. Options are:

•

Standalone (default)

•

MS Based—(Mobile Station Based fix) Uses assistance GPS data from a remote server over the WAN interface

Sets the sensitivity of the GPS heading reading

•

Normal (default)

•

High

It is recommended that you leave the field set to Normal to avoid showing misleading heading values from poor GPS signal (poor sky view, reflections in urban canyon, etc.), but if your GPS application has its own GPS heading sensitivity algorithms, try changing this setting to High.

Servers 1 to 4

You can configure up to four servers as report destinations. Each server is configured independently and can be configured to report the same or different information. This enables you to simultaneously receive GPS and other information at more than one location, either local or remote.

The configuration fields are the same for each of the four servers, except that

Server 1 has the option to configure one or two redundant servers.

Note: These side tabs only appear if GPS Service (on the Global Settings side tab) is

Enabled.

Note: These screens are only visible when GPS is

enabled. See GPS Service on page 208.

To configure one of the servers:

In ACEmanager, go to GPS.

From the menu on the left side of the screen, select the Server you want to configure.

210 4118967

GPS Configuration

Rev 4 Jun.16

Figure 9-4: ACEmanager: GPS > Server 1

211

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Table 9-2: GPS: Servers 1 – 4

Field Description

Events — Configure when the GPS reports are sent

Report Interval Time

(seconds)

GPS Report Time Interval

The amount of time between GPS reports (in seconds)

Options are:

•

1– 65535

•

0 = Disables GPS reporting based on a time interval (default)

With this option disabled, you can still receive reports based on distance traveled or the vehicle being stationary for a configured time. (See

Report Interval Distance

(meters) on page 212 and

Stationary Vehicle Timer (minutes) on page 213.)

You can also use an AT Command to set this value. For more information, see *PPTIME on page 399.

Note: Your cellular carrier may impose a minimum transmit time.

Report Interval

Distance (meters)

GPS Report Distance Interval in meters

The distance (in meters) that the vehicle (or device) travels between sending GPS reports

Options are:

•

40– 65535

Note that setting the resolution near the low end of the range may result in incorrect reports as a result of GPS jitter (i.e. apparent motion caused by the inherent inaccuracy in GPS measurements).

•

0 = Disables sending GPS reports based on a distance interval (default)

With this option disabled, you can still receive reports based on time passed or the vehicle being stationary for a configured time. (See

Report Interval Time (seconds) on page 212 and

Stationary Vehicle Timer (minutes) on page 213.)

You can also use the AT Command, *PPDISTM , to set this value. For more information,

see

page 395

Note: An an additional AT Command,

*PPDIST , allows you to configure the GPS report

distance interval in 100 meter units. This option is only available through AT Commands.

For more information, see page 394 .

Note: If the report interval time and report interval distance fields are both set, GPS reports are sent when either interval is reached. For example, if the time interval is reached, a

GPS report is sent even if the distance is not reached. Conversely, if the vehicle travels the specified distance, a GPS report is sent even if the time interval was not reached.

212 4118967

GPS Configuration

Table 9-2: GPS: Servers 1 – 4

Field Description

Stationary Vehicle

Timer (minutes)

Maximum Speed

Event Report (km/h)

You can use this field if you want to receive less frequent reports when the vehicle is stationary. A GPS report is sent every x minutes the vehicle (or device) is stationary, where x is the value configured in this field. When the vehicle is stationary, this value overrides the value configured in the Report Interval Time field.

Options are:

•

1–255

•

0 = Disables GPS reporting based on a vehicle being stationary (default)

You can also use an AT Command to set this value. For more information, see *PPTSV on page 399.

A GPS report is sent if the speed (in kilometers per hour) configured in this field is exceeded, and again when the speed goes back down below the configured value.

•

0 = Disable (default)

•

1–255

Note: If you are using one of the RAP GPS report types (see GPS Report Type on page 215) the GPS report triggered by this feature includes:

•

A marker to indicate that it was triggered by the configured speed being exceeded and when the speed is goes back down below the configured value.

•

The standard GPS information for the configured report type

For more information, refer to the RAP Protocol Guide.

If you are not using a RAP GPS report, a standard report is sent.

Send Stationary

Vehicle Event in

Seconds

A GPS report is sent if the vehicle (or device) has been in one location for more than the specified time (in seconds) and again when the vehicle (or device) moves from that location. Options are:

•

1–255

•

0 = Disables sending GPS reports based on a vehicle being stationary (default)

Note: If you are using one of the RAP GPS report types (see GPS Report Type on page 215) the GPS report triggered by this feature includes:

•

A marker to indicate that it was triggered by the vehicle either being stationary or starting to move again

•

The standard GPS information for the configured report type

For more information, refer to the RAP Protocol Guide.

If you are not using a RAP GPS report, a standard report is sent.

You can configure Stationary Vehicle Event in Seconds and Stationary Vehicle Timer together to receive a special report when the device is stationary longer than x seconds, a normal report every x minutes it is stationary (instead of the Report Interval Time) and a special report when the vehicle begins moving again.

Rev 4 Jun.16

213

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Table 9-2: GPS: Servers 1 – 4

Field Description

Enable Digital Input

Event

A GPS report is sent if the configured digital input changes. For example, this could be used to trigger a report being sent when an emergency light or siren is turned on or off, or when a door is opened or closed. The GPS data in the report informs you of where the event took place.

Options are:

•

Disable (default)

•

Enable

Note: If you are using one of the RAP GPS report types (see GPS Report Type on page 215) the GPS report triggered by this feature includes:

•

A marker to indicate that it was triggered by a change in status of the configured digital input

•

The standard GPS information for the configured report type

For more information, refer to the RAP Protocol Guide.

If you are not using a RAP GPS report, a standard report is sent.

You can also use an AT Command to set this value. For more information, see

*PPINPUTEVT on page 396.

214 4118967

GPS Configuration

Table 9-2: GPS: Servers 1 – 4

Field Description

Report Type

GPS Report Type

Sets the type of GPS Report

Options are:

RAP

•

GPS Data—RAP GPS report that contains only GPS data

•

GPS+Date—RAP GPS report that contains GPS data with the UTC time and date

(default)

•

GPS+Date+RF—RAP GPS report that contains GPS data, the UTC time and date, and radio frequency information for the cellular connection

•

GPS+Date+RF+EIO—RAP GPS report that contains GPS data, the UTC time and date, radio frequency information for the cellular connection, and the current I/O state

NMEA

•

NMEA GGA+VTG—NMEA GPS report that contains fix information, vector track, and speed over ground

•

NMEA GGA+VTG+RMC—NMEA GPS report that contains fix information, vector track, speed over ground, and recommended minimum GPS data

•

NMEA GGA+VTG+RMC+GSA+GSV—NMEA GPS report that contains fix information, vector track, speed over ground, the recommended minimum GPS data, overall satellite data, and detailed satellite data

TAIP

•

TAIP data—TAIP GPS report that contains position and velocity

•

Compact TAIP data—TAIP GPS report that contains the compact position

•

TAIP LN report—TAIP GPS report that contains a long navigation message

•

TAIP TM report—TAIP GPS report that contains the time and date

XORA

•

XORA data—GPS report used with Xora asset tracking

Note: Only RAP GPS reports can be configured to include odometer and digital I/O information.

Note: You can also use an AT Command to set this value. For more information, see

*PPGPSR on page 396.

Rev 4 Jun.16

215

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Table 9-2: GPS: Servers 1 – 4

Field Description

Servers

—Configure where the reports are sent

Report Server IP

Address

IP address or FQDN (fully qualified domain name) of the server where GPS reports are sent

Example: 192.100.100.100

The IP address can be for a local host or a remote server that is accessed over-the-air or via a VPN tunnel.

If an IP with the last octet of 255 is configured (i.e. 192.168.13.255), a report would be broadcast to all IPs on that subnet. When configured to a local host subnet, any connected device would receive the report.

Note: If you want to use it as a LAN device, it must have a private IP address. If you want

to use a public IP address, use a Local IP report. (See Local/Streaming—Local IP Report on page 224.)

You can also use an AT Command to set this value. For more information, see *PPIP on page 396.

216 4118967

GPS Configuration

Table 9-2: GPS: Servers 1 – 4

Field Description

Report Server Port

Number

Destination port on the server where GPS reports are sent

The destination port can be the same for all servers or you can configure a different destination port for each server. Options are: 1–65535

Defaults:

•

Server 1 destination port: 22335

•

Server 2 destination port: 22336

•

Server 3 destination port: 22337

•

Server 4 destination port: 22338

You can also use an AT Command to set these values. For more information, see

*PPPORT on page 398.

Note: If the account is behind a firewall (for example, an account that is not Internetroutable), the report may be redirected to come from a different source port when it arrives at the server.

The source ports on the device are not configurable. The following source ports are used:

Protocol

RAP / NMEA

TAIP

XORA

Server

Port

17335

17345

17346

17347

21000

21001

21002

21003

9494

9495

9496

9497

Rev 4 Jun.16

217

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Table 9-2: GPS: Servers 1 – 4

Field Description

Redundant Servers — Only available for Server 1

If the redundant server is configured, anytime a report is sent to server 1, an identical report is sent to any configured redundant server(s). Transport/SNF configuration settings do not apply to redundant servers.

Commands from redundant servers are ignored. Reports originate from port 17335. The redundant servers can be a local host or a remote server that is accessed over-the-air or via a VPN tunnel.

Redundant Server 1

IP Address

IP address or FQDN of the first redundant server

Redundant Server 1

Port Number

Port number of the first redundant server

The port number can be the same as or different from that of other servers.

Redundant Server 2

IP Address

Redundant Server 2

Port Number

IP address or FQDN of the second redundant server

Port number of the second redundant server

The port number can be the same as or different from that of other servers.

Minimum Report Time

(secs)

Specifies the minimum time (in seconds) between partial reports or grouped packets being sent

You can also use an AT Command to set this value. For more information, see

*PPMINTIME on page 397.

Transport / Store and Forward (SNF) — This feature is designed to accommodate periods when the AirLink gateway is outside the area of mobile network coverage or otherwise unable to reach the report server.

Reports are stored and then “forwarded” in a combined packet when the device is again able to contact the server.

Enable SNF for

Unreliable Mode

Store and Forward causes GPS reports to be stored if the AirLink gateway goes out of network coverage. Once the device/vehicle is in coverage the stored GPS reports are sent to the server. Options are:

•

Disable (default)—If there is no mobile network coverage, reports are not stored.

•

Enable—If there is no mobile network coverage, reports are stored until the AirLink gateway can access the server.

Note: You can also use an AT Command to set this value. For more information, see

*PPSNF on page 398.

218 4118967

GPS Configuration

Table 9-2: GPS: Servers 1 – 4

Field Description

SNF Reliable Mode

Store and Forward Reliability: GPS reports are retransmitted if not acknowledged by the server.

Options are:

•

OFF (Unreliable Mode) (default)—If this field is Off, the device does not expect acknowledgment to any GPS report sent to the server.

•

Reliable Mode—A sequence number (1–127) is added to each packet (page). The server acknowledges every 8th packet. If there is no ACK from the server, ALEOS pings the server and re-sends the packets when the server responds. If the server receives packets out of sequence, the server NAKs the first and last missed packets.

ALEOS retransmits the missing packets.

Note: Reliable mode is valid only when a RAP report is select as the

GPS Report Type

•

Simple Reliable Mode—ALEOS attempts to contact the server the configured number of times, after which it stops attempting to contact the server and discards messages that cannot be transmitted or received after the configured number of tries. When contacted, the server responds with the ASCII string UDPACK. For information on configuring the maximum number of retries see

SNF Simple Reliable Max Retries on page 219. For information on configuring the backoff time, see SNF Simple Reliable

Backoff Time (secs) on page 219.)

•

UDP Sequence Mode—A hex sequence number (30–7f) is prepended to the packet.

The server responds with SEQACK and the sequence number. The sequence number is not stored and is re-initialized when the AirLink gateway is reset or power cycled.

Unacknowledged packets are dropped after the configured number of retries.

•

TCP Listen Mode—This mode is the same as UDP Sequence Mode, except that the server initiates the connection using TCP. Use this mode if your server is behind a firewall. If you are using this mode, the AirLink gateway must have a mobile terminated/Internet routable IP address.

•

TCP—By default, GPS reports are sent over UDP. Select this option if you want the

GPS reports sent over TCP. Because TCP is an inherently reliable protocol, no additional headers are added to the report packet. TCP works with all GPS report types.

Note: You can also use an AT Command to set this field. For more information, see

*PPSNFR on page 398.

SNF Simple Reliable

Max Retries

SNF Simple Reliable

Backoff Time (secs)

When the AirLink gateway is configured to use Simple Reliable Mode, use this field to set the maximum number of retries when a report is sent and there is no response. Use the

SNF Simple Reliable Backoff Time (secs) field to set the interval between retries.

Options are:

•

Disabled

•

1–255 retries (Default is 10.)

You can also use an AT Command to set this value. For more information, see

*PPMAXRETRIES on page 397.

When the AirLink gateway is configured to use Simple Reliable Mode, use this field to set the interval for the retries. (Use the

SNF Simple Reliable Max Retries field to set the

maximum number of retries.)

•

(Default is 10.)

You can also use an AT Command to set this value. For more information, see

*PPSIMPLETO on page 398.

Rev 4 Jun.16

219

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Table 9-2: GPS: Servers 1 – 4

Field Description

Additional Data

When configured, these options add additional data to RAP reports (see

GPS Report Type on page 215)

sent in response to any trigger.

Report Odometer

Enables odometer reporting. Options are:

•

Disable (default)

•

Enable

You can also use an AT Command to set this value. For more information, see *PPODOM on page 398.

Report Digital Inputs

Enables digital input reporting. Options are:

•

Disable (default)

•

Enable

You can also use an AT Command to set this value. For more information, see

*PPREPORTINPUTS on page 398.

Redundant Servers

When one or two redundant servers are enabled, each time a message is sent out to the main server a second identical message is sent to the redundant server(s).

The redundant servers can be running the same or different application than the primary server. The messages to the redundant server are independent of the primary server settings or state.

You can configure one or both redundant servers. The messages are sent independently to either or both.

Note: Messages are sent whether or not the server is available and do not use any reliable mode format. Receipt of a message is not acknowledged nor is any message resent.

Messages to redundant servers are in UDP only.

GPS RAP Report Sequence Example

In this example:

The AirLink gateway is installed in a police car.

•

Digital input 2 is connected to the switch that controls the siren.

•

Digital input 3 is connected to the laptop docking station.

ACEmanager has the following configuration:

•

Report Interval Time: 30 seconds

•

Report Interval Distance: 150 meters

•

Stationary Vehicle Timer: 5 minutes

•

Send Stationary Vehicle Event in Seconds: 6 seconds

•

Maximum Speed Event: 100 km/h

•

Enable Digital Input Event: Enable

220 4118967

•

Report Type: GPS + Date (RAP GPS report type 0x12)

GPS Configuration

Figure 9-5: GPS > Server 1—Example

The following table provides a sample scenario for this ALEOS configuration.

Event / Action

The AirLink gateway in the police car is connected to power for the first time.

GPS RAP report sent to the server

A 0x10 (power up) report is sent.

The police car is driving around the patrol area.

The police officer spots a speeding vehicle, switches on the siren, and pursues the vehicle.

The vehicle speeds up, with the police car in pursuit.

A 0x12 (GPS + Date) report is sent every 150 meters or every 30 seconds, whichever is less.

Digital input 2 which is connected to the siren switch is triggered and a

0x27 (DIN 2 changes to 1) report is sent.

The vehicle being pursued and the police car slow down.

When the police car exceeds 100 km/h, a 0x2e (maximum speed exceeded) report is sent. A 0x12 (GPS + Date) report is sent every 150 meters.

When the police car’s speed goes below 100 km/h, a 0x2f (return to normal speed) report is sent.

The speeding vehicle pulls over and stops at the side of the road. The police car pulls in behind it. The officer turns off the siren, leaves the engine idling, gets out of the car, and walks over to the other vehicle.

Digital input 2 which is connected to the siren switch is triggered, and a

0x26 (DIN 2 changes to 0) report is sent. Six seconds after the police car comes to a stop, a 0x2c (stationary vehicle event) report is sent. While the car remains stopped with the engine idling, a 0x12 (GPS + Date) report is sent every 5 minutes.

The officer issues a ticket, returns to the police car and drives away.

When the police car is back in motion, a 0x2d (started moving event) report is sent. A 0x12 (GPS + Date) report is sent every 150 meters or

30 seconds, whichever is less.

Rev 4 Jun.16

221

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Event / Action

The police car stops in front of the police station.

The officer disconnects the laptop from the dock.

GPS RAP report sent to the server

Six seconds after the car stops, a 0x2c (stationary vehicle event) report is sent.

Digital input 3 connected to the docking station is triggered. A 0x28 (DIN

3 changes to 0) report is sent.

Local/Streaming

Some in-vehicle/navigation applications accept GPS reports via a serial connection, generally using either NMEA or TAIP. To configure serial streaming for DB-9 (RS-232) ports and/or USB Serial ports, go to GPS > Local Streaming.

Reports are send as ASCII text.

Note: These screens are only visible when GPS is enabled. See GPS Service on page 208.

Figure 9-6: ACEmanager: GPS > Local/Streaming

222 4118967

GPS Configuration

Table 9-3: GPS: Local/Streaming

Field Description

Serial

GPS Reports port

The serial port or USB serial link that reports are sent to

Options are:

•

NONE (default)

•

DB9 Serial

•

USB Serial

•

DB9 and USB

You can also use an AT Command to set this value. For more information, see *PGPS on page 393.

Note: If you want to stream GPS data to a USB port, the USB port must be configured on

the LAN > USB page to act as a serial port. See USB Device Mode on page 101.

GPS Reports Type

GPS Reports

Frequency (secs)

ASCII text GPS Report type to send via the serial link:

•

NMEA GGA+VTG+RMC—NMEA GPS report that contains fix information and vector track and speed over ground, and recommended minimum GPS data (default)

•

NMEA GGA+VTG+RMC+GSA+GSV—NMEA GPS report that contains fix information and vector track and speed over ground, the recommended minimum GPS data, overall satellite data, and detailed satellite data

•

TAIP data—TAIP GPS report that contains position and velocity

•

TAIP compact data—TAIP GPS report that contains the compact position

•

TAIP LN report—TAIP GPS report that contains a long navigation message

•

TAIP TM report—TAIP GPS report that contains the time and date

You can also use an AT Command to set this value. For more information, see *PGPSR on page 394.

How frequently (in seconds) the GPS report is sent to the serial link

Options are:

•

1– 65535—(up to 18.2 hours)

You can also use an AT Command to set this value. For more information, see

*PGPSF on page 394.

Rev 4 Jun.16

223

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Table 9-3: GPS: Local/Streaming

Field Description

GPS Coverage

This field refers to the mobile network coverage.

Options are:

•

ALWAYS (default)—GPS reports are always streamed to the serial link.

•

Out of Coverage—GPS reports are only streamed to the serial link when the device has no cellular connection.

You can also use an AT Command to set this value. For more information, see *PGPSC on page 393.

Tip:

The Out of Coverage option enables you to use a back-up in-vehicle mapping application that does not rely on mobile network access.

GPS Reports Delay

(secs)

The delay (in seconds) before the out of the coverage stream begins. This field only applies if the GPS coverage field is set to “Out of Coverage”.

•

0 (default)

•

1–255

You can also use an AT Command to set this value. For more information, see *PGPSD on page 394.

Local/Streaming—Local IP Report

Local IP reports are limited to tethered IP-based LAN devices (Ethernet, USB/net,

DUN, PPPoE). Local IP reports do not have any transport/SNF options. The reports are always sent regardless of cellular coverage. Reports are sent over

UDP.

The destination IP cannot be configured directly. The first connected LAN device is used. If multiple devices are connected, the priority is the device using the

Public IP address, or if all devices are using Private IP addresses, the priority is:

•

Ethernet

•

USB

•

DUN

Note: These screens are only visible when GPS is enabled. See GPS Service on page 208.

224 4118967

GPS Configuration

Figure 9-7: ACEmanager: GPS > Local/Streaming: Local IP report

Table 9-4: GPS: Local/Streaming — Local IP Report

Field Description

Local Reporting Time

Interval (Secs)

The frequency (in seconds) of the reports

Options are:

•

0 = Disable (default)

•

1–255

You can also use an AT Command to set this value. For more information, see *PPLATS on page 396.

Note: If the Local Reporting Time Interval is set to 1 second, there may be some variation in the report interval, with the report interval sometimes being less than 1 second and sometimes more than 1 second. Other settings for this field are accurate.

Rev 4 Jun.16

225

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Table 9-4: GPS: Local/Streaming — Local IP Report

Field Description

Local Report Type

Sets one of the following Local Report types:

RAP

•

GPS Data—RAP GPS report that contains only GPS data

•

GPS+Date—RAP GPS report that contains GPS data with the UTC time and date

(default)

•

GPS+Date+RF—RAP GPS report that contains GPS data, the UTC time and date, and radio frequency information for the cellular connection

•

GPS+Date+RF+EIO—RAP GPS report that contains GPS data, the UTC time and date, radio frequency information for the cellular connection, and the current I/O state

NMEA

•

NMEA GGA+VTG—NMEA GPS report that contains fix information, vector track, and speed over ground

•

NMEA GGA+VTG+RMC—NMEA GPS report that contains fix information, vector track, speed over ground, and recommended minimum GPS data

•

NMEA GGA+VTG+RMC+GSA+GSV—NMEA GPS report that contains fix information, vector track, speed over ground, the recommended minimum GPS data, overall satellite data, and detailed satellite data

TAIP

•

TAIP data—TAIP GPS report that contains position and velocity

•

Compact TAIP data—TAIP GPS report that contains the compact position

•

TAIP LN report—TAIP GPS report that contains a long navigation message

•

TAIP TM report—TAIP GPS report that contains the time and date.

Note: You can also use an AT Command to set this value. For more information, see

*PPLATSR on page 397.

Note: Local IP Report does not have an option for Xora reports.

Starting Destination

Port

Number of Extra

Destination Ports

The primary port that reports are sent to

The Local IP report source port is 17335. This is not configurable.

You can send the report to up to 7 additional consecutive ports. For example, if the starting port is 12351 and you set this field to 5, reports are sent to ports 12351, 12352, 12353,

12354, 12355, and 12356.

The default is 0 which means only the starting port is used.

You can also use an AT Command to set this value. For more information, see

*PPLATSEXTRA on page 397.

226 4118967

GPS Configuration

Table 9-4: GPS: Local/Streaming — Local IP Report

Field Description

Device ID in Local

Reports

Allows use of the IMEI/ESN or phone number in local IP RAP reports to identify a device/ vehicle. Options are:

•

None (default)

•

Phone Number

•

ESN/IMEI

Tip:

Including the device ID is especially useful when your devices have dynamic IP addresses.

Local Report

Destination IP

Note: If you want the device ID included in all other RAP GPS reports, see

Use Device ID in Location Reports on page 209.

This read-only field shows the IP address of the destination that Local IP reports are send to. Through its use of DHCP, ALEOS detects if there is a connected device and designates that device's IP as the local IP destination. When no device is connected at startup, ALEOS uses the first IP address in the Ethernet DHCP pool as the destination. When using Public mode for an interface, that interface will be the local IP destination even if it's not the first device connected.

Note: The Local Report Destination IP is not configurable. If you want a GPS report to go

to a specific device IP, user Server 1–4 configuration. (See Servers 1 to 4 on page 210.)

Report Odometer

Enables odometer reporting

Options are:

•

Disable (default)

•

Enable

Note: Only applies for RAP report types.

Report Digital Inputs

Enables digital input reporting. Options are:

•

Disable (default)

•

Enable

Note: Only applies for RAP report types.

Rev 4 Jun.16

227

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

228 4118967

Rev 4 Jun.16

10: Events Reporting Configuration

Introduction

You can configure the AirLink gateway to generate reports or initiate actions based on specified events. Events can either be generated internally, such as a change in GPS fix status or a signal quality indicator crossing a specified threshold, or by external devices attached to the analog or digital inputs.

Events that can trigger reports or actions include:

•

A switch on connected equipment opens or closes (digital input)

•

A pulse accumulation crosses a configured threshold

•

An analog meter on connected equipment crosses a configured threshold (Analog input is reported in volts or transformed to meaningful units.)

•

Changes to GPS information such as a GPS fix obtained or lost, changes in vehicle speed or heading, engine hours threshold crossed

•

Changes to network status such as signal strength, network state, and network service

•

The gateway’s power supply (in volts) crosses a configured threshold

•

The AirLink gateway board or radio temperature crosses a configured threshold

•

A configured threshold for daily or monthly data usage is crossed

Depending on the type of report, reports can be sent to a local or remote report server, an email address, or by SMS to a cell phone.

The occurrence of a configured event can also turn on or off a relay link.

Figure 10-1 summarizes how Event reporting works.

229

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Internet

Report server

Local server

Connected equipment

External Events, e.g.

- Digital I/O

- Analog I/O

- Relay control

AirLink gateway

Internal Events, e.g.

- RSSI

- Temperature

- GPS

Figure 10-1: Events Reporting

Computer

Cellular

Network

SMS

Cell phone

Events/Actions are not one shot activities. After an Action is performed, the Event is still active and will trigger an Action the next time the state change or threshold crossing occurs.

A single Event may activate one or more Actions. For example, if RSSI is below threshold, you can send an email (Action 1) and send an SMS message (Action

2).

A single Action may be activated by one or more Events. For example, if either the network state changes to Network Ready or the RSSI crosses a configured threshold, the same Action is performed.

Configuring Events Reporting

Before you begin

If you plan to use either of the following, configure that feature in ACEmanager before configuring Events Reporting:

•

Email (

Email (SMTP) on page 189)

•

SNMP Trap ( Management (SNMP) on page 192)

Configuring Events Reporting

When configuring Events Reporting, first configure the Action (that is, how you want to be notified when the Event occurs). Then configure the Event you want reported, and finally, link the Event to the Action.

Note: All Events Reporting configuration changes take effect after a short delay (about one minute). No reboot of the AirLink gateway is necessary.

230 4118967

Rev 4 Jun.16

Events Reporting Configuration

Configuring the Action

Note: You can define a maximum of 5 Actions.

If an Action requires an IP connection, the following source ports are used. These are not configurable.

Actions (in the order configured)

Action 1

Action 2

17348

17349

Source port

Action 3

Action 4

Action 5

17351

17352

17353

Click the appropriate link for instructions on configuring the desired Action. Once

the Action is configured, proceed to Event Types on page 243.

•

•

•

•

GPS RAP Report 13

· NMEA GGA+TGV

· NMEA GGA+VTG+RMC

· NMEA GGA+VTG+RMC+GSA+GSV

· TAIP data

· TAIP LN report

· TAIP TM report

· XORA report

•

Events Protocol Reports

· Type, Length, Value

· Binary

· CSV- ASCII

· XML

•

Turn Off Services

Email

Note: Sending an email report is limited to SMTP servers that are open and do not require a secure login.

231

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

To configure ALEOS to send an email report:

Ensure that email is configured on the Services > Email (SMTP) screen. (See

Email (SMTP)

on page 189

On the Events Reporting tab, select Actions from the menu on the left.

Enter the desired Action Name.

From the drop-down menu in the Action Type field, select Email.

232

Figure 10-2: ACEmanager: Events Reporting > Actions

Complete the Email Information section with the recipient’s email address, the subject line, and the desired message.

In the Body Type field, select the desired format for the Data Group information included in the report.

In the Data Group section, select the data to be included in the email report.

For more information on the options, see Report Data Group on page 240.

4118967

Rev 4 Jun.16

Events Reporting Configuration

Click Apply.

The name you assigned to the Action appears under Actions. You can click on this anytime to modify the settings.

Optional—If desired, after you have updated all the fields and clicked the

Apply button, wait about 1 minute, and then click the Test report button to send a test email to verify that the destination and format are correct.

10. Click Events on the menu on the left and follow the instructions on

Event

Types on page 243 to configure the Event you want associated with this

Action and to link the Action to the Event.

SMS

Note: You can only send SMS from your AirLink gateway if your cellular account allows

SMS. You may need to have SMS added to the account. SMS from data accounts is blocked on some mobile networks. Outgoing SMS messages are limited to 140 characters.

If the selected data exceeds 140 characters, the message is truncated.

To configure ALEOS to send an SMS message:

On the Events Reporting tab, select Actions from the menu on the left.

Enter the desired Action Name.

From the drop-down menu in the Action Type field, select SMS.

233

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

234

Figure 10-3: ACEmanager: Events Reporting > Action Type SMS

Complete the SMS Information section with the recipient’s phone number and the desired message to be included with the information from the Data

Groups. The combined message and Data Group information cannot exceed

140 characters.

In the Data Group section, select any data you would like to be included in the

SMS. For more information on the options, see

Report Data Group on page 240.

Click Apply.

The name you assigned to the Action appears under Actions. You can click on this anytime to modify the settings.

Optional—If desired, after you have updated all the fields and clicked the

Apply button, wait until the progress circle disappears (about 30 seconds), and then click the Test report button to send a test SMS.

4118967

Events Reporting Configuration

Click Events on the menu on the left and follow the instructions on

Event

Types on page 243 to configure the Event you want associated with this

Action and to link the Action to the Event.

Relay Link

When an event occurs, you can signal or control connected devices using the gateway’s relay outputs. The power connector has one relay.

Note: The relays are capable of switching small loads. If you need to switch a larger load, such as to open a door lock, connect the AirLink gateway’s relay to an externally powered switch.

To configure ALEOS to turn a relay link on or off:

On the Events Reporting tab, select Actions from the menu on the left.

Enter the desired Action Name.

From the drop-down menu in the Action Type field, select Relay Link.

Rev 4 Jun.16

Figure 10-4: ACEmanager: Events Reporting > Action Type > Relay Link

In the Relay Type drop-down menu, select the desired Action:

· Relay 1—Open

· Relay 1, Inverted—Close

Click Apply.

The name you assigned to the Action appears under Actions. You can click on this anytime to modify the settings.

Click Events on the menu on the left and follow the instructions on

Event

Types on page 243 to configure the Event you want associated with this

Action and to link the Action to the Event.

235

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

SNMP TRAP

To configure ALEOS to send an SNMP TRAP notification:

Ensure that SNMP is configured on the Services > Management (SNMP)

page. (See

Management (SNMP)

on page 192

On the Events Reporting tab, select Actions from the menu on the left.

Enter the desired Action Name.

From the drop-down menu in the Action Type field, select SNMP TRAP.

236

Figure 10-5: ACEmanager: Events Reporting > Action Type > SNMP TRAP

Click Apply.

The name you assigned to the Action appears under Actions. You can click on this anytime to modify the settings.

Click Events on the menu on the left and follow the instructions on

Event

Types on page 243 to configure the Event you want associated with this

Action and to link the Action to the Event.

If you have more than one event or action configured, the trap indicates which

Event triggered which Action.

GPS Reports

GPS reports can be sent using:

•

Standard NMEA, TAIP, and XORA

•

Sierra Wireless’ Remote Application Protocol (RAP)

RAP reports are very small and conserve over-the-air bandwidth. They can include vehicle odometer and digital input information.

To configure ALEOS to send a GPS report:

On the Events Reporting tab, select Actions from the menu on the left.

Enter the desired Action Name.

From the drop-down menu in the Action Type field, select the desired type of

GPS report.

Note: For more information on GPS report types, see GPS Report Type on page 215.

4118967

Events Reporting Configuration

Rev 4 Jun.16

Figure 10-6: ACEmanager: Events Reporting > Action Type > TAIP data

Enter the server information and if desired, the store and forward SNF parameters.

Note: The Reliable, Simple Reliable, and UDP Sequence SNF modes apply only to RAP

reports. For more information on SNF, see page 218

Optional (GPS RAP Report 13 only)—Enable Report Odometer and/or

Report Digital Inputs.

Click Apply.

The name you assigned to the Action appears under Actions. You can click on this anytime to modify the settings.

Click Events on the menu on the left and follow the instructions on

Event

Types on page 243 to configure the Event you want associated with this

Action and to link the Action to the Event.

Events Protocol Reports

Sierra Wireless’ Events Reporting protocol allows for messages to be sent to the report server in four formats:

•

1 — Type, Length, Value (TLV) — The TLV message consists of the MSCI

ID as the type, the length of the data, and the actual data.

•

2 — Binary — A binary condensed form of the TLV message

•

3 — CSV-ASCII — An ASCII condensed and comma-delimited form of the

TLV message

•

4 — XML — An XML form of the data

237

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Tip:

Because of its flexibility and robustness, the TLV message type is recommended for most reports using the Events Protocol. The Binary and ASCII forms do not contain a “type field” which can result in misinterpretation of data. Since the TLV and XML forms always include the type as well as the data, an unintentional type can be identified much easier.

To configure an Events protocol report:

On the Events Reporting tab, select Actions from the menu on the left.

Enter the desired Action Name.

From the drop-down menu in the Action Type field, select the desired Events protocol report format.

238 4118967

Events Reporting Configuration

Rev 4 Jun.16

Figure 10-7: ACEmanager: Events Reporting > Action Type > Type, Length, Value

Enter the server information and if desired, the store and forward parameters.

In the Data Group section, select any data you would like to be included in the report. For more information on the options, see

Report Data Group on page 240.

Click Apply.

The name you assigned to the Action appears under Actions. You can click on this anytime to modify the settings.

239

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Click Events on the menu on the left and follow the instructions on

Event

Types on page 243 to configure the Event you want associated with this

Action and to link the Action to the Event.

Turn Off Services

This setting limits services and is primarily used in conjunction with monitoring data usage. For example, you could set the AirLink gateway to limit network service when data usage exceeds a configured threshold. For more information,

see Data Usage on page 267.

Figure 10-8: ACEmanager: Events > Actions > Action Type > Turn Off Services

Turn Off Services does not turn off all network use. Reports are still sent and over-the-air access to the device is allowed. You can still access the AirLink gateway locally, but Ethernet, USBnet access to the mobile network is blocked.

Report Data Group

For email, SMS, and Events Protocol (TLV, Binary, CSV-ASCII, and XML) messages, you can select the data you want to be included in the report. Check the box corresponding to the data displayed. By default, all the boxes are clear.

240 4118967

Events Reporting Configuration

Rev 4 Jun.16

Figure 10-9: ACEmanager: Events Reporting > Action (Data Group)

The reports attributes are:

•

Digital and Analog I/O

· Include Digital Input 1—The status of the digital input

· Include Digital Output 1—The status of the digital output

· Include Pulse Accumulator—The pulse count for the digital input

•

AVL

· Include Satellite Fix—Whether or not there is a usable GPS satellite fix

· Include Latitude—The latitude reported by GPS

· Include Longitude—The longitude reported by GPS

· Include Satellite Count—The number of satellites the GPS is using to get a satellite fix

· Include Vehicle Speed—The speed of the vehicle reported by GPS

· Include Vehicle Heading—The direction the vehicle is traveling reported by

GPS

· Include Engine Hours—The number of hours the engine has been on, based on either Power In or Ignition Sense

· Include Odometer—The number of miles reported by GPS

· Include TAIP ID—The TAIP ID for the AirLink gateway

•

Device Name

These elements in the Device Name group are general identifiers for the Air-

Link gateway and its cellular account.

· Include Device ID—The device ID (serial number) for the AirLink gateway

· Include Phone Number—The phone number of the AirLink gateway

· Include Device Name—The name of the AirLink gateway

· Include MAC Address—The MAC Address of the Ethernet port of the

AirLink gateway

241

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

· Include SIM ID—The SIM ID of the AirLink gateway

· Include IMSI—The IMSI of the SIM installed in the AirLink gateway

· Include GPRS Operator—The wireless Mobile Network Operator the SIM card is associated with

· Include Time—The time the AirLink gateway is active

•

Network Data

The Network Data in this group relates to the mobile network and the connection state of the AirLink gateway.

· Include Network State—The network state for the AirLink gateway

· Include Network Channel—The network channel to which the AirLink gateway is connected

· Include RSSI—The signal strength for the AirLink gateway

· Radio Technology—Type of service being used by the device (e.g. EV-DO

HSPA, LTE)

· Include Network Service—The network service for the AirLink gateway

· Include Network IP—The IP address given by the mobile network

· Include Daily Usage —The daily usage of the Active SIM card (Units as configured on the Applications > Data Usage screen)

· Include Daily Usage SIM 1—The daily usage of the SIM card in slot 1

(Units as configured on the Applications > Data Usage screen)

· Include Daily Usage SIM 2—The daily usage of the SIM card in slot 2

(Units as configured on the Applications > Data Usage screen)

· Include Monthly Usage —The monthly usage of the Active SIM card (Units as configured on the Applications > Data Usage screen)

· Include Monthly Usage SIM 1—The monthly usage of the SIM card in slot 1

(Units as configured on the Applications > Data Usage screen)

· Include Monthly Usage SIM 2—The monthly usage of the SIM card in slot 2

(Units as configured on the Applications > Data Usage screen)

•

Tx/Rx

The Network Traffic in this group relates to the mobile network and the network between the AirLink gateway and any directly connected device(s).

· Include Bytes Sent—The number of bytes sent on the mobile network since last reset

· Include Bytes Received—The number of bytes received from the mobile network since last reset

· Include Host Bytes Sent—The number of bytes sent from the network between the AirLink gateway and the connected device(s) since last reset

· Include Host Bytes Received—The number of bytes received from the network between the AirLink gateway and the connected device(s) since last reset

· Include IP Packets Sent—The number of IP packets sent on the mobile network since last reset

· Include IP Packets Received—The number of IP packets received from the mobile network since last reset

· Include Host IP Packets Sent—The number of IP packets sent from the network between the AirLink gateway and the connected device(s) since last reset

242 4118967

Events Reporting Configuration

· Include Host IP Packets Received—The number of IP packets received from the network between the AirLink gateway and the connected device(s) since last reset

•

Misc Data

Miscellaneous Data includes temperature rates and other information that does not fit in the other categories

· Include Power In—The voltage level of the power coming in to the AirLink gateway at the time of the report

· Include Board Temperature—The temperature of the internal hardware of the AirLink gateway at the time of the report

· Include Host Comm State—The signal level between the AirLink gateway and the connected device(s)

· Radio Temperature—The temperature of the internal radio module

· CDMA PRL Version—PRL version used by the AirLink gateway

· CDMA EC/IO—The quality of the signal from the cellular CDMA network

· GSM EC/IO—The quality of the signal from the cellular GSM network

· Cell Info—The mobile network cell information for the AirLink gateway

Event Types

Note: You can define a maximum of 5 Events.

To define an Event:

On the Event Reporting tab, select Events > Add New from the menu on the left.

Rev 4 Jun.16

Figure 10-10: ACEmanager: Events Reporting, Events > Add New

Enter the desired name for the Event.

Select the Event type from the drop-down menu.

Select the Event Operator and the Value to Compare. The options available depend on the Event type you choose. See

Table 10-1 on page 244 for a list

of options for each Event type.

243

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

All the configured Actions appear at the bottom of the screen. Select the check box beside the Action you want to associate this Event with.

Click Apply.

Figure 10-11: ACEmanager: Events Reporting > Events

Table 10-1: Event Types

Event Name Event Type

Digital Inputs

Digital Input

The AirLink RV50 gateway has 1 digital input.

Pulse Accumulator

The AirLink RV50 gateway

State Change

Event Operator Options

•

Disable

•

When Switch Closed

•

When Switch Opened

•

On any change

Threshold Crossing

•

Disable

•

When Changed By

Analog Input (volts)

Threshold Crossing

Transformed Analog

Threshold Crossing

•

Disable

•

When Above Threshold

•

When Below Threshold

•

When Cross Threshold

•

Disable

•

When Above Threshold

•

When Below Threshold

•

When Cross Threshold

Values to Compare

N/A

•

Pulse Accumulator Delta

•

Starting Trigger Value

Value To Compare (Threshold

(volts))

Value To Compare

(Units configured on the I/O screen) See

Transformed

Analog on page 282.

244 4118967

Table 10-1: Event Types (Continued)

AVL

GPS Fix

State Change

Vehicle Speed

Heading Change

Engine Hours

Threshold Crossing

•

Disable

•

Fix Lost

•

Fix Obtained

•

On any change

•

Disable

•

When Above Threshold

•

When Below Threshold

•

When Cross Threshold

•

Disable

•

Change in Direction

•

Disable

•

When Changed By

Network

RSSI

Threshold Crossing

Network State

Network Service

State Change

•

Disable

•

When Above Threshold

•

When Below Threshold

•

When Cross Threshold

•

Disable

•

When Cellular is Ready

(Triggered when a cellular connection is established)

•

Disable

•

On Service

•

On No Service

•

On Change

Other Report Types

Periodic Reports

Power In

Threshold Crossing

(Time)

•

Disable

•

Periodically

Threshold Crossing

•

Disable

•

When Above Threshold

•

When Below Threshold

•

When Cross Threshold

Events Reporting Configuration

N/A

Value To Compare (Vehicle

Speed (KM/h))

Value To Compare (Heading

Change (degrees))

Value To Compare (Engine

Hours)

Value To Compare (Signal

Power (-dBm))

N/A

Value To Compare (Network

Service):

•

Roaming

•

2G Service

•

Rev A or HSUPA

•

Any Data Service

Value To Compare: Report

Period (secs)

Note: The minimum interval between periodic reports is

3 seconds. Setting an interval less than 3 seconds results in only one report being sent.

Value To Compare (Power In

Threshold (volts))

Rev 4 Jun.16

245

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Table 10-1: Event Types (Continued)

Board Temperature

Threshold Crossing

Radio Temperature

Threshold Crossing

•

Disable

•

When Above Threshold

•

When Below Threshold

•

When Cross Threshold

•

Disable

•

When Above Threshold

•

When Below Threshold

•

When Cross Threshold

Value To Compare

(Temperature Threshold (°C))

Value To Compare

(Temperature Threshold (°C))

Data Usage

For the AirLink RV50, you can choose whether the Event is for the SIM card in slot 1 or slot 2.

Daily Data Usage

Threshold Crossing

Monthly Data Usage

Threshold Crossing

•

Disable

•

When Above Threshold

•

Disable

•

When Above Threshold

Value To Compare

(% of Limit)

Value To Compare

(% of Limit)

Note: You can only configure one Event with either a Daily Data Usage or Monthly Data Usage trigger. If you configure more than one, for example, a trigger when the Daily Data Usage reaches a certain percentage and a trigger when the

Monthly Data Usage reaches a certain percentage, only the last threshold configured is used.

ALEOS Data Usage is approximate and should not be compared with data usage recorded by the Mobile Network

Operator. SIERRA WIRELESS IS NOT RESPONSIBLE FOR DATA OVERAGES.

246 4118967

Rev 4 Jun.16

11: Serial Configuration

Use the serial port to connect devices or computers using a DB9-

RS232 connection.

Note: These commands are specific to the RS232 port and generally do not apply to USB/serial.

Port Configuration

Serial Port Configuration consists of five categories of configurable parameters:

•

Port Configuration on page 248

•

•

•

•

247

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Port Configuration

Figure 11-1: ACEmanager: Serial > Port Configuration > Port Configuration

Table 11-1: Serial Port Configuration > Port Configuration

Field Description

Port Configuration

Serial Port

This field allows you to disable the serial port. Default is Enable.

248 4118967

Serial Configuration

Table 11-1: Serial Port Configuration > Port Configuration

Field Description

Startup Mode Default

Default power-up mode for the serial port. When the AirLink gateway is power-cycled, the serial port enters the communication mode specified.

Note: It can take up to 5 minutes to establish a connection.

•

Normal (AT command) default

•

PPP

•

UDP

•

TCP

•

Reverse Telnet/SSH—Allows you to telnet or SSH into a router or other device connected to the AirLink gateway via a serial port. For information on configuring

reverse telnet, see Reverse Telnet/SSH on page 251.

•

Modbus ASCII

•

Modbus RTU (Binary)

•

BSAP—Bristol Standard Asynchronous Protocol

•

Variable Modbus

•

UDP Multiple Unicast—Data from the serial port is packed into UDP packets and sent to multiple IP addresses (for example, multiple AirLink gateways). For more information, see

UDP Multiple Unicast on page 253.

You can also use an AT command to configure this field. See MD on page 401.

login Reverse Telnet

This field only appears when the Startup Mode Default field is set to Reverse Telnet/SSH.

Determines the log in procedure when using reverse telnet.

•

Enable—Do not enter a user name and password when you telnet to a a router or other device that has a serial connection to your AirLink gateway. Login is automatic.

(default)

•

Disable—Enter a user name and password when you telnet to a a router or other device that has a serial connection to your AirLink gateway.

For more information about reverse telnet, see

Reverse Telnet/SSH on page 251.

Configure Serial Port

Format: [speed][data bits][parity][stop bits]

Valid speeds are 300–115200, data bits: 7 or 8, parity: O,E,N,M, stop bits: 1,1.5.

Default is 115200,8N1.

You can also use an AT command to configure this field. See S23 on page 409.

Flow Control

Serial port flow control setting

•

None—No flow control is being used (default)

•

Hardware—RTS/CTS hardware flow control is being used

•

Transparent SW—Transparent software flow control. Uses escaped XON and XOFF for flow control. XON and XOFF characters in data stream are escaped with the @ character (0x40). @ in data is sent as @@.

You can also use an AT command to configure this field. See \Q on page 408.

DB9 Serial Echo

AT command echo mode

•

Enable—Text is visible as you type (default)

•

Disable—Text you type is not visible

You can also use an AT command to configure this field. See E on page 408.

Rev 4 Jun.16

249

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Table 11-1: Serial Port Configuration > Port Configuration

Field Description

Data Forwarding

Timeout (.1 seconds)

Data Forwarding

Character

Device Port

The Data Forwarding Timeout feature causes ALEOS to wait until no data has been received on the serial port for the specified period of time beyond the built-in delay of

100 ms before sending a new PAD packet.

Acceptable values are: 0–255. (Unit is 0.1 second; default is 1.)

If the field is set to 0 or 1, the feature is disabled. ALEOS sends the new PAD packet after the built-in 100 ms delay.

Data Forwarding Timeout is not applicable to AT and PPP modes.

PAD data forwarding character. ASCII code of character that causes data to be forwarded.

Used in UDP or TCP PAD mode

Default is 0 (No forwarding character).

You can also use an AT command to configure this field. See S51 on page 403.

The port on the AirLink gateway used for incoming TCP/UDP communication (Default is

12345)

If either, or both, of the UDP Answer or TCP Answer parameters are enabled, when the

AirLink gateway receives incoming TCP or UDP packets that are destined for this port, it strips off the IP header and send the packet payload out its serial port.

You can also use an AT command to configure this field. See *DPORT on page 400.

Serial MTU

Destination Port

Destination Address

The serial maximum transmit unit (PAD payload)

Valid range: 256–4096 bytes (Default is 1304)

Recommended settings:

•

UDP PAD—1472 bytes

•

TCP PAD—1460 bytes

You can also use an AT command to configure this field. See *UDPPADMTU on page 405.

The destination port that TCP/UDP communication is sent to

You can also use an AT command to configure this field. See S53 on page 403.

IP address TCP/UDP communication is sent to

You can also use an AT command to configure this field. See S53 on page 403.

Default Dial Mode

Host Authentication

Mode

PPP User ID

PPP Password

Protocol used to send messages

Options are:

•

TCP

•

UDP (default)

You can also use an AT command to configure this field. See S53 on page 403.

Sets the authentication method the host uses for PPP. Options are:

•

None (default)

•

CHAP—The stronger of the two protocols. Recommended, provided it is supported by all the client devices

•

PAP and CHAP—If CHAP is not supported by the client, the host reverts to PAP.

Sets the User ID for authentication

Sets the User Password for authentication

250 4118967

Rev 4 Jun.16

Serial Configuration

Reverse Telnet/SSH

The Reverse Telnet/SSH feature allows you to connect to and configure a router or other device that has a serial connection to your AirLink gateway.

You can have only one Reverse Telnet session open at a time. If a new Reverse

Telnet session is started, any existing Reverse Telnet connection will be closed.

However, you can simultaneously have:

•

One Telnet session for Reverse Telnet (using the port configured in the

Device Port field on the Serial > Port Configuration page)

•

One Telnet session for AT Commands (using the port configured in the

Remote Login Server Telnet Port field on the Services > Telnet/SSH page)

Note: If you are using Reverse Telnet and you have VPNs, the more VPN tunnels in use, the greater the CPU load. This may result in lower throughput or greater delays.

To configure Reverse Telnet/SSH:

Log into ACEmanager and go to Serial > Port Configuration.

In the Startup Mode Default field, select Reverse Telnet/SSH.

In the Configure Serial Port field, set the speed, data bits, parity, and stop bits. (The serial port configuration depends on the router you want to connect to. For example, to connect to a Cisco router that has a default baud rate of

9600, enter 9600,8N1 in the Configure Serial Port field.)

251

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

252

Optional—If you are planning to use telnet (rather than SSH), you can be automatically logged in when you telnet to the AirLink gateway without having to enter a user name and password. login is not supported with SSH.

To set up automatic login:

In the login Reverse Telnet field, select Enable.

b. Click Apply.

Go to Services > Telnet/SSH.

In the Remote Login Server Mode field, select:

· Telnet—if you want to Telnet into the connected device

· SSH—if you want to SSH into the connected device

Note: If you enabled login, select Telnet.

Click Apply.

Reboot the AirLink gateway.

Use a Telnet or SSH terminal client such as Putty or Teraterm to connect to the appropriate port:

· If you are using login, Telnet to the port specified in the Device Port field

(default is 12345). SSH is not available with login.

· If you are not using login, you can Telnet or SSH into the port specified in the Remote Login Server Telnet/SSH Port field (default is 2332).

4118967

10. If prompted, log in with the following credentials:

· User name: sconsole

· Password: 12345 (default)

Serial Configuration

Rev 4 Jun.16

For information on changing the default reverse telnet password, see

Change

Password on page 285.

ALEOS redirects you to the router or other device connected to the AirLink gateway serial port. You can use this connection to configure connected device.

Note: You may be required to enter a user name and password to access the router or other device.

UDP Multiple Unicast

With UDP Multiple Unicast, data from the serial port is packed into UDP packets and sent to multiple IP addresses. To configure UDP Multiple Unicast:

Configuration.

In the Startup Mode Default field, select UDP Multiple Unicast.

In the Destination Port field, enter the remote port to be used.

Click Apply.

Go to Serial > Modbus Address List and enter the index numbers and IP

addresses of the devices you want the data sent to. (See on page 261.)

Click Apply.

Reboot the device.

Note: To avoid flooding the network, there is a 20 millisecond pause between sending the

UDP packet to each destination.

253

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Advanced

Figure 11-2: ACEmanager: Serial > Port Configuration > Advanced

Table 11-2: Serial Port Configuration > Advanced

Field Description

Advanced

Assert DSR

Assert DCD

DTR Mode

Assert DSR always when the device is in a data mode (UDP, TCP, etc.), or when the device is in network coverage. Options are:

•

Always (default)

•

In Data Mode

•

In Coverage

You can also use an AT command to configure this field. See &S on page 408.

Assert DCD always, or when the device is in a data mode (UDP, TCP, etc.) or when the device is in network coverage. Options are:

•

Always

•

In Data Mode (default)

•

In Coverage

You can also use an AT command to configure this field. See &C on page 406.

Use DTR from the serial device, or ignore DTR (same as

S211 on page 410). Options are:

•

Use DTR

•

Ignore DTR (default)

254 4118967

Serial Configuration

Table 11-2: Serial Port Configuration > Advanced

Field Description

Quiet Mode

AT Verbose Mode

Disable or enable display of device responses. Options are:

•

Disable (default)

•

Enable

You can also use an AT command to configure this field. See Q on page 408.

Sets the level of information returned for AT commands

Options are:

•

Verbose (default)

•

Numeric

You can also use an AT command to configure this field. See V on page 410.

Call Progress Result

Mode

Convert 12 digit

Number to IP Address

Disable ATZ Reset

IP List Dial

Keep Alive Mode

Keep Alive delay

When enabled adds 19200 to CONNECT messages

Options are:

•

Disable (default)

•

Enable

You can also use an AT command to configure this field. See X on page 410.

Choose whether a 12-digit number is converted to an IP address (eg. 111222333444 to

111.222.333.444). Options are:

•

Use as Name (default)

•

Use as IP

You can also use an AT command to configure this field. See *NUMTOIP on page 403

The value set in this field determines whether or not issuing an ATZ Command resets the

AirLink gateway. Options are:

•

On — Block is enabled—ATZ does not reset the device.

•

Off —Block is disabled—ATZ resets the device. (default)

You can also use an AT command to configure this field. See *DATZ on page 407.

This allows access to the Modbus IP Address using the first two digits of the dial string. For example, ATDT1234567 would imply ID index 12 on the Modbus Address list and use the associated IP Address as the destination. Options are:

•

Disable (default)

•

Enable

You can also use an AT command to configure this field. See IPL on page 403.

When this feature is enabled, the AirLink gateway reboots if there is no traffic for longer than the period configured in the Keep Alive Delay field. Options are”

•

Disable (default)

•

Enable

When Keep Alive Mode is enabled, use this field to set the delay (in minutes) before the

AirLink gateway reboots if there is no traffic on the serial port. Accepted values:

•

10–65535 (Default is 10.)

Rev 4 Jun.16

255

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

TCP

Figure 11-3: ACEmanager: Serial > Port Configuration > TCP

Table 11-3: Serial Port Configuration > TCP

Field Description

TCP

TCP Auto Answer

This determines how the AirLink gateway responds to an incoming TCP connection request. The AirLink gateway remains in AT Command mode until a connection request is received. The AirLink gateway sends a “RING” string to the host. A “CONNECT” sent to the host indicates acknowledgment of the connection request and the TCP session is established.

•

Disable (default)

•

Enable

You can also use an AT command to configure this field. See S0 on page 409.

TCP Connect Timeout

(seconds)

TCP Idle Timeout

Specifies the number of seconds to wait for a TCP connection to be established when dialing out (Default is 30.)

You can also use an AT command to configure this field.

TCP idle time-out in the configured units (See

TCP Idle Timeout Unit on page 257.)

Specifies a time interval upon which if there is no in or outbound traffic through a TCP connection, the connection is terminated.

Default is 5.

You can also use an AT command to configure this field. See TCPT on page 404.

256 4118967

Serial Configuration

Table 11-3: Serial Port Configuration > TCP

Field Description

TCP Idle Timeout Unit

Units used for the TCP Idle Timeout Interval.

Options are:

•

Minutes (default)

•

Seconds

You can also use an AT command to configure this field. See TCPS on page 404.

TCP Connect

Response Delay

(seconds)

Include Device ID on

TCP Connect

The number of seconds to delay the “CONNECT' response upon establishing a TCP connection, or the number of tenths of seconds to delay before outputting ENQ on the serial port after the CONNECT when the ENQ feature is enabled.

•

0–255 (Default is 0.)

You can also use an AT command to configure this field. See S221 on page 410.

If this option is enabled, after a TCP connection is established, ALEOS sends a packet that contains the device ID (and optionally a prefix, suffix, and CRLF). Options are:

•

Disable (default)

•

Enable

Note: To use this feature, ensure that the Device ID is configured in the Use Device ID in

Location Reports field on the GPS screen (GPS > Global Settings > General). See Global

Settings on page 208.

Device ID Prefix

Device ID Suffix

Send CR LF after

Device ID

Sets the Prefix DID in the device identification packet upon TCP connection. Maximum length of the prefix is 80 characters.

Sets the Suffix DID in the device identification packet upon TCP connection. Maximum length of the suffix is 80 characters.

Enables a carriage return to be inserted in the device identification packet after the Suffix

DID. Options are:

•

no CR LF

•

send CR

•

send CR LF (carriage return, line feed) Default

Rev 4 Jun.16

257

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

UDP

Figure 11-4: ACEmanager: Serial > Port Configuration > UDP

Table 11-4: Serial Port Configuration > UDP

Field Description

UDP

UDP Auto Answer

UDP Idle Timeout

(seconds)

Whether the AirLink gateway answers and incoming UDP connection request

Options are:

•

Disable (default)

•

Enable

You can also use an AT command to configure this field. See S82 on page 404.

UDP Idle Time-out in seconds

Specifies a time interval upon which if there is no in or outbound traffic through a UDP connection, the connection is terminated.

•

0— No idle time-out

•

1–255 Time-out in seconds (Default is 50.)

You can also use an AT command to configure this field. See S83 on page 404.

258 4118967

Serial Configuration

Table 11-4: Serial Port Configuration > UDP

Field Description

UDP Connect Last

Allows you to choose to use the last accepted IP address and port number as the default settings, instead of using S53 (destination address)

Options are:

•

Do not change S53 (default)

•

Set S53 last IP

Note: Resetting the device restores the configured S53 (destination address).

You can also use an AT command to configure this field. See *UDPLAST on page 405.

Allow Any Incoming IP

When UDP answer is enabled, use this field to select whether to allow any incoming IP address to connect or to only allow the configured destination IP address to connect.

Options are:

•

Allow only S53 (default)

•

Allow any IP address

If you select Allow only S53, the Destination Port and Destination Address fields under

Serial > Port Configuration must be configured. (See Table 11-1 on page 248.)

You can also use an AT command to configure this field. See AIP on page 400.

Allow All UDP

UDP Auto Answer

Response

Accepts UDP packets from all IP addresses when a UDP session is active. If there is no

UDP session active, an incoming UDP packet is treated according to the UDP answer and

AIP settings. Options are:

•

No effect (default)

•

Allow all—The AirLink gateway accepts all UDP traffic from any IP address during a

UDP session.

You can also use an AT command to configure this field. See *UALL on page 404.

Half-Open Response—In UDP answer (half-open) mode. Options are:

•

No Response—No Response codes when UDP session is initiated (default)

•

RING CONNECT—RING CONNECT response codes sent out serial link before the data from the first UDP packet

Dial UDP Always

UDP Serial Delay

(.1 second)

Note: Quiet Mode must be Off.

You can also use an AT command to configure this field. See HOR on page 408.

The dial command always uses UDP, even when using ATDT. Options are:

•

Disable—Dial using the means specified (default)

•

Enable—Dial UDP always, even when using ATDT

Note: When this parameter is set you cannot establish a TCP PAD connection.

You can also use an AT command to configure this field. See *DU on page 400.

Waits the specified delay before sending the first received UDP packet and the subsequent

UDP packets out to the serial port (in 100 ms units).

•

No UDP packet delay (default)

•

1–255— Delay in 100 ms units, from 100 ms to 25.5 sec.

You can also use an AT command to configure this field. See *USD on page 405.

Rev 4 Jun.16

259

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Table 11-4: Serial Port Configuration > UDP

Field Description

UDP Keepalive

(seconds)

UDP Recovery Ping

Use this field to configure the time interval (in seconds) for sending UDP keepalive packets.

Options are:

•

1–65535—ALEOS sends a UDP packet, containing the AirLink gateway’s IMEI (in little endian) to the configured Destination IP Address:Destination Port when the UDP connection is first established and then at the configured interval.

If the AirLink gateways WAN IP address changes, a UDP packet is sent and the timer is reset.

•

0—UDP Keepalive is disabled. (default)

If an IP is provided in this field and no UDP packets are received from the server for the

UDP Idle Timeout period, the gateway sends a single ping to this IP.

This functionality is designed to resolve a known issue where a Verizon Wireless GX440 becomes temporarily unreachable from the mobile network after a period of time in which no data is sent or received.

PPP

Use Point-to-Point Protocol (PPP) to establish a connection between a host PC serial port and the AirLink gateway, as shown in

Figure 11-5

PPP connection

Host PC

Figure 11-5: PPP connection

Serial cable

AirLink gateway

WAN connection

Internet

260

Figure 11-6: ACEmanager: Serial > Port Configuration >PPP

4118967

Serial Configuration

Table 11-5: Serial Port Configuration > PPP

Field

PPP a

Description

Device PPP IP

Host PPP IP

Sets the device IP address (in private mode)

Sets the host IP address (in private mode) a. Note: This section is only visible when PPP is selected in the Startup Mode Default field.

Modbus Address List

To add a Modbus Address:

Click Add More.

Enter the Index number, an equal sign, and the IP address. For example:

10=123.123.123.123 (decimal)

0xA=123.123.123.123 (hex) Prefix 0x to hex numbers.

Including the port number after the IP address is optional. If you include the port number, separate the port number and IP address by a colon.

For example:

10=123.123.123.123:11223

0xA=123.123.123.123:11223

Rev 4 Jun.16

Figure 11-7: Serial > MODBUS Address List

Click Apply.

Reboot.

To delete an address from the list, click the X beside it.

261

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Note: You can also use the AT Commands MLIST and MLISTX to add address entries and

MLIST? or MLISTX? to query the entries on the list. See MLIST on page 401, and

MLISTX on page 402.

Configuring IP to Serial with Answer and

Serial to IP

You can configure the AirLink gateway to:

•

Answer incoming TCP/IP or UDP/IP connections and send the packet payload out the AirLink gateway’s serial port to a connected device

•

Create and send TCP/IP or UDP/IP packets containing payload data that the

AirLink gateway receives over its serial port from a connected device

•

Both receive and send TCP/IP or UDP/IP packets (that is, both of the above functionalities)

Internet

Serial

Receive packets; send payload data out over serial

Receive payload data over serial; create and send out packets

TCP /IP packet

UDP/IP packet

TCP /IP packet

UDP/IP packet

AirLink gateway

Connected device

Packet contents streamed over serial

Both: receive packets; send payload data out over serial AND receive payload data, create and send out packets

TCP /IP packet

UDP/IP packet

Figure 11-8: TCP and UDP Answer

Packet contents streamed over serial

To configure the AirLink gateway for TCP/UDP answer, sending IP packets or both:

In ACEmanager, go to Serial > Port Configuration.

262 4118967

Serial Configuration

Required fields for receiving data payloads over serial, creating IP packets to send

Required fields for receiving IP packets and sending out data payloads over serial

Required fields both receiving data payloads over serial, creating IP packets to send and receiving data payloads over serial, creating IP packets to send

Figure 11-9: ACEmanager: Serial > Port Configuration

Use

Table 11-6 and the instructions following the table to configure the

desired options for this feature.

Table 11-6: Quick Guide to Configuring IP to Serial with Answer and Serial to IP

Field To receive packets and send data payload out over serial

To receive data payloads over serial and send out packets

Both (to receive packets - send out data payload AND receive data payload and send out packets)

N/A UDP or TCP UDP or TCP Startup Mode Default

See step Step 3 .

Configure Serial Port

See

Step 4 .

Flow Control

See

Step 5 .

Device Port

See

Step 6 .

115200,8N1

None

12345

115200,8N1

None

N/A

115200,8N1

None

12345

Rev 4 Jun.16

263

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Table 11-6: Quick Guide to Configuring IP to Serial with Answer and Serial to IP

Field To receive packets and send data payload out over serial

To receive data payloads over serial and send out packets

Both (to receive packets - send out data payload AND receive data payload and send out packets)

N/A Required Required Destination Port

See

Step 7 .

Destination Address

See

Step 8 .

N/A Required Required

Startup Default Mode—When the Startup Mode is set to UDP or TCP, the

AirLink gateway takes any data sent to its serial port by a connected device and encapsulates it into a TCP/IP or UDP/IP packet.

Configure Serial Port—Set the baud rate of the serial port on the AirLink gateway so that it matches the baud rate of the serial port on the connected device. (The default baud rate is 115200 bps.) You can also use this field to set the framing characteristics for the serial port communication on those rare occasions when the default value of 8N1 does not apply.

Flow Control—This field can usually be left at the default value (None) as most serial devices use only a 3-wire connection (Tx, RX, and Gnd).

However, if the serial device uses the RTS and CTS pins on the serial connection to control data flow between the two devices, set this field to

Hardware.

Device Port—Data received on a TCP/IP or UDP/IP connection to the configured Device Port is sent out the serial port. The default value for the port:

· On the AirLink gateway is 12345

Destination Port—The AirLink gateway uses the port value specified in this field to determine which port it sends the IP packet containing the data payload to. The AirLink gateway enters the value in the Destination Port field in the header of the IP packet it creates.

Destination Address—The AirLink gateway uses the IP address specified in this field to determine the IP address to send the packet it creates to. The

AirLink gateway enters this IP address in the header of the IP packet it creates.

If you are configuring the AirLink gateway to:

· Create and send packets only, go to step Step 10 .

· Receive TCP/UDP packets, complete the following instructions.

264 4118967

Rev 4 Jun.16

For Receiving TCP/IP Packets: a.

Expand the +TCP section of the screen.

Serial Configuration

Figure 11-10: ACEmanager: Serial > Port Configuration > TCP

b. Set the TCP Answer field to Enable.

For Receiving UDP/IP Packets: a.

Expand the +UDP section of the screen.

Figure 11-11: ACEmanager: Serial > Port Configuration > UDP

b. Set the UDP Answer field to Enable.

Set the Allow Any Incoming IP field to Allow Any IP. (If this field is left at the default value, the AirLink gateway only accepts incoming UDP/IP packets from the IP address specified in the Destination Address field in the Port Configuration section of the screen.

10. For information on the other parameters, see

Port Configuration on page 247.

11. Click Apply.

12. Click Reboot (in the upper right of the screen).

13. Once the reboot is complete, this feature is enabled.

If the packet contents are not being sent to the connected device, see the troubleshooting information in

TCP/IP and UDP/IP Auto Answer on page 445.

265

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

LED Indicator

You can configure the Activity LED on the AirLink gateway to flash red when traffic is being transmitter or received over the serial port.

Figure 11-12: ACEmanager: Serial > LED Indicator

Table 11-7: Serial > LED Indicator

Field

Display

Description

Options are:

•

Disable (default)

•

Enable

If this field is set to Enable, the Activity LED on the AirLink gateway flashes red when traffic is being transmitted/received on the serial port selected in the Serial Port field.

Off

Activity LED

Flashing Green

Flashing Red

Flashing Yellow

Traffic

No traffic

Traffic on WAN interface

Traffic on selected serial port

Traffic on both the WAN interface and selected serial port

You can also use an AT command to configure this field. See

*SERIALLEDDISPLAY on page 404. For a complete list of LED

behavior, refer to the AirLink gateway Hardware User Guide.

266 4118967

Rev 4 Jun.16

12: Applications Configuration

The Applications tab consists of a Data Usage section, a Garmin application, and an ALEOS Application Framework section.

Data Usage

Note: Before configuring

Data Usage, ensure that the AirLink gateway receives date and time information from the mobile network, or from

GPS in the case of an

RV50 gateway using GPS.

You can also use the

ACEmanager SNTP client to receive time from an

SNTP server. (See

Time

(SNTP) on page 197.) If

necessary, contact your

Mobile Network Operator to confirm that the mobile network provides date and time information to connected devices.

The Data Usage feature on the Applications tab in conjunction with

Events Reporting provides you with a way to actively monitor cellular data usage.

Once data usage is configured, you can use event reporting to:

•

Actively monitor the cellular data usage by configuring monthly and/or daily usage level thresholds that result in notifications being sent to you (e.g. email, SMS, or SNMP Trap) when the threshold is reached.

•

Limit mobile network communication until the end of the billing period when the data limit is reached by blocking connected LAN devices from using the mobile network. Traffic sent to and from the AirLink gateway is not blocked. Over-the-air access to

ACEmanager and the Telnet/SSH AT interface is still available.

Note: You can configure Events Reporting to notify you when the threshold set in Data Usage is reached, but ALEOS does not block further access to the mobile network, unless you also create a second action to Turn Off

Services.

Note: ALEOS Data Usage is approximate and should not be compared with data usage recorded by the Mobile Network Operator.

Sierra Wireless is NOT responsible for data overages.

Step 1—Configure Data Usage

In ACEmanager, go to Applications > Data Usage.

In the Usage Monitoring field, select Enable.

In the side menu, select the screen for the SIM slot you want to configure (Data Usage Slot 1 or Data Usage Slot 2).

Data usage monitors the slot. If you change the SIM card in the slot being monitored, the data usage tracked is the accumulative data usage for all SIM cards placed in that slot.

Enter the desired values in the Daily or Monthly Limit fields (in

GB or MB), and the day of the month that the billing cycle starts.

For more details, see the table starting on

page 268

267

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Click Apply.

268

Figure 12-1: ACEmanager: Applications > Data Usage Slot 1

Field

General

Usage Monitoring

Plan Units

Description

Use this field to enable or disable data usage monitoring. Options are:

•

Disable (default)

•

Enable

Select the units used for your data plan. The options are:

•

MB—Megabytes (default)

•

KB—Kilobytes

Note: When you change the units in this field, the units for values in

the Daily Limit and

Monthly Limit

fields are not converted and must be updated manually.

4118967

Rev 4 Jun.16

Applications Configuration

Field

Daily Limit

Description

This is the user-specified daily (24 hour) data usage limit (in MB or KB, depending on the value in the

Plan Units

field). You can specify data usage limits on a daily basis. A limit is essentially a threshold that can trigger the software to take a user-specified action if the usage goes above the threshold. See

Events Reporting Configuration on page 229.

Note: The Daily Limit value MUST be expressed as an integer (i.e., a whole number) and NOT as a fraction (e.g., “3.5”).

Note: Daily usage is cleared at midnight, UTC.

Caution:

Data usage limits are approximate and based on reporting conditions in ALEOS. Data usage may run over the amount set in this field before the action specified for the threshold trigger takes effect.

Tip:

ALEOS reads the data usage every 3 to 5 minutes. If you are using an application that requires high data usage, you can set an alert to warn you when data usage reaches a safe limit that takes into account the amount of data expected over the 3 to 5 minutes between data usage readings. For information on how to set an alert or other action, see

Events Reporting Configuration on page 229.

Current Daily Usage

Displays the current daily data usage (in MB or KB, depending on the

option selected in the Plan Units field)

Note: Data usage includes data sent and data received.

269

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Field

Monthly Limit

Description

This is the user-specified monthly data usage limit (in MB or KB, depending on the option selected in the

Plan Units field). Data usage

accumulates on a monthly basis and on the date you specified (the

“rolling month”). Data usage accumulates during the month until the end of the next billing period, at which point the data usage totals are reset.

Note: The Monthly Limit value MUST be expressed as an integer (i.e., a whole number) and NOT as a fraction (e.g., “3.5”)

Note: Monthly usage is cleared at midnight, UTC on the last day of the billing cycle.

Current Monthly

Caution:

Displays the current monthly data usage (in MB or KB, depending on

the value configured in Plan Units on page 268.)

Note: Data usage includes data sent and data received.

Start of Billing Cycle

(Day of Month)

Enter the desired start of the billing cycle. For example, 3 (Day 3 of every month)

Changing the value in this field resets the Current Monthly field to zero.

Previous Day

Previous Daily Usage

Shows the data usage for the previous day (in MB or KB, depending on

the value configured in Plan Units on page 268.)

Note: Data usage includes data sent and data received.

270 4118967

Applications Configuration

Step 2—Configure Event Reporting

In ACEmanager, go to Events Reporting > Actions.

Rev 4 Jun.16

Figure 12-2: ACEmanager: Events Reporting > Actions

Select the desired Action to be performed when the Event is triggered, such as SNMP Trap or Email, and enter the appropriate information in the related

fields. For detailed instructions, see Configuring Events Reporting on page 230.

Some reports give you the option to include additional information. If applicable, select the check box(es) in the Data Group section of the screen to indicate the information to be included in the report.

271

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Note: You can have more than one Action for a single Event, but you can only have one

Daily Usage and one Monthly Usage Event.

Click Apply.

Go to Events Reporting > Events and configure a data usage threshold.

The threshold is specified as a percentage of the monthly or daily limit. For example, if you have a monthly limit of 5 GB, and the threshold is set at 80%, then threshold is reached at 4 GB of data. For detailed instructions, see

Configuring Events Reporting on page 230.

272

Figure 12-3: ACEmanager: Events Reporting > Events

At the bottom of the screen, select the check box beside the Action you want to associate the Event with.

Click Apply.

Stopping Service when the Event Reporting Threshold is Reached

When you are approaching the data plan limit, you may want to turn off cellular communication to any LAN connected user devices until the next billing cycle starts.

To turn off services on the data plan when the limit is reached:

In ACEmanager, go to Events Reporting and select Actions Add New on the left menu.

Enter the desired name for the action.

In the Action Type field, select Turn Off Services.

When triggered, this action prevents cellular communication to all LAN connected devices. Traffic sent from the AirLink gateway is not blocked. Over-theair access to ACEmanager and the Telnet/SSH AT interface is still available.

4118967

Applications Configuration

Figure 12-4: ACEmanager: Events Reporting

Click Apply.

Select Events on the left menu.

Enter the desired Event Name.

In the Event Type field, select either Daily Data Usage or Monthly Data

Usage.

In the Event Operator field, select When Above Threshold.

Set the desired Value to Compare (% of limit).

10. At the bottom of the screen, select the check box beside the Action you want to associate the Event with.

Rev 4 Jun.16

Figure 12-5: ACEmanager: Events Reporting > Events

11. Click Apply.

Note: When the configured threshold is crossed, all traffic between connected devices and the cellular network is blocked. This helps to reduce data usage, but it does not completely stop it. Traffic to and from the AirLink gateway is not blocked, and over-the-air access to

273

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

ACEmanager and the Telnet/SSH AT interface is still available.

Setting the “Turn Off Services” threshold at a level below 100% of the data plan helps to reduce data usage before the data plan limits are exceeded.

Garmin

Garmin provides navigation devices for versatile fleet monitoring solutions. AirLink gateways provide Internet access to Garmin devices and a mechanism to enable via cellular. ALEOS also monitors links to the Garmin device and communication between the Garmin device and the server.

To configure Garmin in ACEmanager:

Under the Applications > Garmin, set the Garmin Device Attached feature to

Enabled.

Figure 12-6: ACEmanager: Applications > Garmin

Go to Serial > Port Configuration.

· Set the Startup Mode Default field to TCP.

· Set the Server Address and Port for TCP.

· Set the Destination Port and the Destination Address to the port and address of the AVL server that the TCP application will be communicating with.

Configure the serial port. To communicate with Garmin:

· Input 9600, 8N1 in Configure Serial Port

· Select None in Flow Control

· Select Ignore DTR in DTR Mode.

274 4118967

Applications Configuration

Rev 4 Jun.16

Figure 12-7: ACEmanager: Serial > Port Configuration

Check the Garmin’s communications status under the Status > Applications tab. Garmin data service states are:

· Not Enabled — Not acknowledged by the AVL server

· Enabled — Acknowledged by the AVL server.

275

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

276

Figure 12-8: ACEmanager: Status > Applications > Garmin Status

Reboot the AirLink gateway to apply the changes. The “Garmin Status” now appears:

· Enabled — Acknowledged by the AVL server.

Note: The Garmin Status field appears only if the Garmin application is Connected.

ALEOS Application Framework

ALEOS Application Framework (AAF) allows you to develop your own applications to run inside an AirLink gateway and leverage the ALEOS Application

Platform ( source.sierrawireless.com/resources/airlink/aleos_af/aleos_af_home/ ) or a customer-developed server platform.

Sierra Wireless gateways come without an AAF user password. Before using

AAF, select a password and go to Admin > Change Password to enter it. See AAF

User Password on page 286. The AAF Development Studio (DevStudio)

application uses this password to communicate with the gateway.

Once the AAF user password is set up, embedded and server application developers can start using AAF by accessing the ALEOS Application Platform

( source.sierrawireless.com/resources/airlink/aleos_af/aleos_af_home/ ).

You may want to reserve the serial port for an AAF application. To do so, select

Enable in Applications > ALEOS Application Framework > Serial Port Reserved.

It is not necessary to reserve the serial port before activating AAF.

Reserving the serial port is mandatory only if the AAF application will be using the serial port.

4118967

Applications Configuration

Note: When you reserve the serial port for AAF, it cannot be used for any other serialrelated ALEOS features.

Rev 4 Jun.16

Figure 12-9: ACEmanager: Applications >ALEOS Application Framework

Field Description

General

Available RAM (KB)

Available Flash (KB)

CPU Load

(Last 15 minutes)

ALEOS Application

Framework

Available RAM in kilobytes (1000 bytes), updated every 30 seconds

Available Flash on the user partition in kilobytes (1024 bytes), updated every 30 seconds

CPU load, averaged over the last 15 minutes and updated every 30 seconds

The CPU load relates to how many applications are attempting to execute in parallel over the 15-minute period. If the load is greater than

1, some applications are waiting for CPU capacity to become available and may be delayed in launching.

Enable or disable (default) the ALEOS Application Framework (ALEOS

AF). If enabled, ALEOS AF starts at boot time. When the Reset to

Factory default button on the Admin > Advanced page is pressed,

ALEOS AF is disabled.

Serial Port Reserved

Select Enable to reserve the serial port for ALEOS AF. When this field is set to Enable, the serial port cannot be used for any other serialrelated ALEOS features. The options are:

•

Disable (default)

•

Enable

277

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Field

QCOM DM Port

Resource Reserve

Description

Reserves the QCOM DM port for ALEOS AF applications. Options are:

Enable (Reserve access for ALEOS AF) or Disable (Reserve access for ALEOS). Default: Disable

Installed AAF Applications

Application Name start

Version

Status

To help you manage installed applications, the table in this section shows all the installed AAF Applications and displays the:

•

Application name

•

start—true or false

•

Version

•

Status—STARTED or STOPPED

If no applications are installed, the table displays the message:

“No application installed or AAF not started”.

278 4118967

Rev 4 Jun.16

13: I/O Configuration

The I/O tab in ACEmanager applies to all Sierra Wireless AirLink gateways that feature I/O ports.

You can use the input/outputs on AirLink gateways to generate reports based on a threshold being crossed, a switch being opened or closed, or the number of times a switch has changed state.

Use the Events Reporting screen to configure reports. (See Events

Reporting Configuration on page 229.) Use the I/O screen to view the

current state of the analog and digital inputs, to turn the relays on and off, and to configure the units you want used in the reports based on analog inputs.

The number of digital and analog input/outputs depends on the device.

AirLink RV50

The AirLink RV50 has:

•

One pin (Pin 4 on the power connector) that can be configured as a digital input/output, relay output, or analog input.

More information

For more information, refer to the Hardware Configuration User

Guide for your AirLink gateway.

Analog inputs

Analog inputs monitor a voltage range in small increments. This allows you to monitor equipment that reports status as an analog voltage. Examples include:

•

Power supply voltage

•

Temperature, weight, volume, flow represented as voltage

•

An incremental gauge with a voltage output

•

Vehicle battery voltage

The raw data for the changes being monitored is in volts, but you can use the I/O Configuration screen in ACEmanager to convert voltage

to the desired units of measurement. See Transformed Analog on page 282.

279

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Digital inputs

Digital inputs monitor contact closures on a switch. This allows you to monitor changes such as:

•

When a door or latch is open or closed

•

When a container is full or empty

•

When a switch or valve is opened or closed

•

The level of fuel in a vehicle (connected to an on/off sensor)

•

When the trunk of a vehicle is opened or closed

You can use Events Reporting to generate reports and actions based on the digital input values.

Volts

≤ 1.0

≥ 2.7

Digital 0

Digital 1

Interpreted as

For more information on setting up reports, see

Events Reporting Configuration on page 229.

Relay outputs

You can use relay outputs to trigger an intermediary switch and change the state of equipment.

Current State

The Current State screen allows you to view the current values (as of the last refresh) of analog and digital inputs, pulse counts for digital inputs, and raw and transformed values for analog inputs. You can also use this screen to change the current values for Relay outputs. This change occurs immediately without a reboot.

Figure 13-1: ACEmanager: I/O > Current State

280 4118967

I/O Configuration

Table 13-1: I/O: Current State

Command Description

Digital Input 1 value

Pulse Count 1

Displays the current value for the digital input:

•

0 —Open

•

1 —Closed

Digital input 1 displays the value for Pin 4 on power connector.

You can also use an AT command to read these values. See *DIGITALIN1?

on page 411.

The pulse count increments when the input value changes from high to low.

Pulse count 1 displays the value for Pin 4 on power connector.

Note:

To reset the pulse count to zero, reset the device to the factory defaults.

Analog Input 1 (Volts)

Transformed Analog 1

Relay Output 1

Analog input

You can also use the AT Command *DIGITALIN1?

to query this setting. See page 411

The analog input expressed in the configured units. See Transformed Analog on page 282.

Controls the internal current sink that you can use to drive a relay or for other use purposes where a switchable low side current sink is required. For more details refer to the hardware user guide. Options are:

•

OFF (default)—The current sink is deactivated.

•

Drive Active Low—The current sink is activated.

Note: You cannot set this field to Drive Action Low if the I/O line is already being used

for Standby mode.

You can also use an AT command (see *RELAYOUT1 on page 411), an SMS

command (see [prefix]relay x y on page 420), or a RAP command (refer to the Remote

Application Protocol User Guide) to configure this field.

Note: Changes to this field go into effect immediately. No reboot of the AirLink gateway is necessary.

Pulse Count

Pulse Count details:

•

Pulses are counted on falling edge (high to low).

•

Repeated pulses cannot be counted when the device is powered off, or being reset. However, a single change in state while the device is powered off or being reset is counted properly.

•

To reset the pulse count to zero, reset the device to the factory defaults.

Rev 4 Jun.16

281

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Configuration

This screen allows you to configure the initial relay settings and to transform units of measurement for the analog inputs from volts to a more appropriate unit, if applicable. Generated reports use the transformed value configured on this screen.

For more information, refer to the Hardware Configuration User Guide for your

AirLink gateway.

Figure 13-2: ACEmanager: I/O > Configuration

Field

Relay Initial Setting

Pull-up for I/O 1

Description

The initial setting for the current sink when the AirLink gateway is powered on

Options are:

•

OFF (default)

•

Last Value (The value remains the same as it was before the AirLink gateway was powered down).

When you change this field, the corresponding digital input value on this screen reflects the change after a screen refresh.

Controls the internal pull-up resistor on the I/O line. Options are:

•

Disable—The pull-up is disabled. (Default)

•

Enable—The pull-up is enabled.

The pull-up voltage is based on V in

Guide.

. For details, refer to the AirLink RV50 Hardware User

Note: You cannot enable the Pull-up for I/O, if the I/O line is already being used for

Standby

mode.

Transformed Analog

The raw analog data is displayed in volts. However, that is not always the most convenient unit of measurement to view the data. The I/O Configuration screen enables you to transform the voltage readings to a more convenient unit of measurement, for example degrees Celsius or Fahrenheit for temperature, liters for volume, etc.

282 4118967

Rev 4 Jun.16

I/O Configuration

Step 1—Coefficient and Offset

Before you configure ACEmanager, you need to locate or calculate the coefficient and the offset values.

Consult the user documentation for the equipment you want to monitor. It should provide you with the coefficient to convert volts to the appropriate unit of measurement and the offset value (the difference between the equivalent value for 0 volts and 0), or provide information on equivalent values for voltage readings from which you can calculate the coefficient and offset. (If this information is not available in the user documentation, contact the manufacturer.)

For example, if the equipment monitors temperature, and has a scale from 0 volts to 30 volts, the equipment specifications should provide information similar to the following:

0 V is equivalent to - 20°C

30 V is equivalent to 100°C

This is expressed algebraically as follows:

0V +

= – 20

C a

30V +

= 100C where: a = coefficient b = offset

For this example, you can calculate a as follows:

(

30V +

)

–

(

0V +

–

(

– 20

)

30V = 120V

= 4

To calculate b, substitute a into the first equation above:

0V +

= – 20

Step 2—Configure ACEmanager

For each of the analog inputs you want to configure:

In ACEmanager, go to I/O > Configuration.

Enter the values for the coefficient and offset. (In this example, the coefficient is 4 and the offset is -20.)

Enter the desired unit of measurement. (In this example, the unit of measurement is C, for degrees Celsius).

ACEmanager shows the value of the transformed analog input as temperature in

283

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Note: A reboot is required after configuring the transformed analog values.

284 4118967

14: Admin

Change Password

For system security reasons, changing the default password of the

AirLink gateway is highly recommended.

Rev 4 Jun.16

Figure 14-1: ACEmanager: Admin

To change the default password:

Select the User Name associated with the password you want to change: user, viewer, or sconsole.

(To create an AAF user password, see

AAF User Password on page 286.)

Enter the old password.

Enter the new password twice.

The password can be 4 to 32 characters long and can contain a mixture of letters, numbers, and/or special characters. The password is case sensitive.

Note: If the password is lost, the only way to recover access to the AirLink gateway is to use the hardware reset button to reset the device to the factory default settings. If the reset button has been disabled (using the

Default

Configuration Reset

field on the Admin > Advanced screen) prior to the password being lost, the only way to recover access to the AirLink gateway is through AirLink Management Services, for which an account is required.

Click Change Password.

If you want to confirm that the password has been changed, log out and then log in with the new password.

285

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Note: There are two user levels in the User Name drop-down menu. The ‘user’ has full administrator rights and can edit the configuration; the ‘viewer’ can only view the configuration and status of the device. Viewer can change the ‘viewer’ password. User can change both.

AAF User Password

An AAF user password is required if you want to use ALEOS Application

Framework (AAF) to develop your own applications to run inside an AirLink gateway. This password is used when installing an AAF application from

DevStudio onto the gateway.

To enter an AAF user password:

In ACEmanager, go to Admin > Change Password.

From the User Name drop-down menu, select AAF user.

Figure 14-2: ACEmanager > Change Password (AAF user)

Enter the new password twice and click Change Password.

Reboot the gateway.

For more information on using ALEOS Application Framework , see page 276 .

286 4118967

Rev 4 Jun.16

Admin

Advanced

Features which should be rarely changed and will affect the operation of the device are present on the Advanced screen.

Figure 14-3: ACEmanager: Admin > Advanced

287

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Field Description

Date and Time

Queries the internal clock. The date and time are always specified in 24-hour notation

(UTC).

•

mm/dd/yyyy=date in month/day/year notation

•

hh:mm:ss=time in 24-hour notation

Default Configuration

Reset

Enables or disables the hardware reset button

Sets the AirLink gateway to allow (or not allow) the hardware reset button to reset the device to the factory default settings.

•

Allowed—Pressing the hardware reset button for 7–10 seconds reboots the device and resets it to the factory defaults. (When resetting the device to factory default settings, release the reset when all four LEDs turn from red to yellow.)

•

Not Allowed—Pressing the hardware reset button reboots the device, but does not reset it to the factory defaults.

Note: This field only affects the hardware reset button on the device. You can always use the “Reset to Factory Defaults” button in ACEmanager to reset the device.

Note: If this field is set to “Not Allowed” and the login password is subsequently lost, the only way to regain access to the AirLink gateway is through AirLink Management Service

(account required).

Status Update

Address

Enter the device Name/Port. Name is the domain name or IP address, and Port is the port of the device where the device status updates (in XML format) will be sent. This report can be sent to a LAN connected device (e.g., 192.168.13.100/1122) or a remote location

(e.g., newb.eairlink.com/17000).

The time interval (in seconds) when a status update should be sent

Status Update Period

(seconds)

Power Input Voltage

(volts)

Displays the power input voltage in volts. If the input voltage ground is connected to the

AirLink gateway case (without serial connection), this value reads .3 V (approx.) less; if ground is connected (with serial connection), the value reads .3 V (approx.) more.

Board Temperature

(Celsius)

Displays the board temperature in degrees (Celsius)

Radio Module Internal

Temperature

(Celsius)

Displays the temperature of the internal radio module in degrees (Celsius).

Number of System

Resets

Periodic Reset Timer

(hours)

Time of Day (ToD)

Reset: Reset Interval

(days)

Count of the number of system resets over the life of the device or since the last configuration reset

Resets the device after the specified number of hours.

0 = Disabled

Number of days between resets

0 = Disabled

Example: If this field is set to 3, the device resets every third day.

288 4118967

Field Description

ToD Reset: Time Zone

Offset from UTC

Time zone adjustment (Offset in easterly direction from UTC Time)

Possible values are -12...12

Example: Pacific Standard Time would be -7

ToD Reset: Hour of day when Reset occurs

The local hour of the day when the reset occurs

Possible values are 0–23

Example: 4 is 4:00 am

Admin

Rev 4 Jun.16

289

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Field

Ping

Description

Use this button to confirm that a connected device is responding.

Click Ping.

In the pop-up window, enter the device IP address or DNS name and click Ping Now.

IP Logging

IP Logging is used to troubleshoot issues such as:

•

Problems with the LAN or WAN connection to an AirLink gateway

•

Uncertainty about where a packet is coming from

•

Issues with port forwarding not working properly

IP Logging enables you to log network traffic and save it in a form that can be analyzed by

Sierra Wireless engineers. Before using IP Logging, contact your authorized AirLink reseller or Sierra Wireless representative to discuss the issue you are observing and obtain a .cmd file to capture the appropriate related IP traffic. When you receive the file, save it to your computer’s hard drive.

To use IP logging:

Obtain a command (.cmd) file from Sierra Wireless.

In ACEmanager, go to Admin > Advanced and click IP Logging.

In the pop-up window, click Browse and navigate to the command file you received from Sierra Wireless.

Click Open.

The file name appears in the field beside the Browse... button.

Click Upload File.

290 4118967

Field

IP Logging

(continued)

Admin

Description

Once you see a message at the bottom of the window saying that the file has been successfully uploaded, select a command from the drop-down menu, as advised by your support contact.

Rev 4 Jun.16

Click the Start button.

Note: If you are running more than one command, run each command sequentially and save the results before selecting the next command to run. Running a new command or rerunning the same command wipes out the results from the previous run.

When the logging is complete, the log shows the number of packets captured, received, and dropped.

Note: If the log shows only “Got 0”, no logs were captured. Contact Sierra Wireless.

291

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Description Field

IP Logging

(continued)

Once the logging is compete, click the Download IP Logging File button at the bottom of the screen, save the tarred gzip file (file extension .tgz) to your computer, and email it to your support contact.

292 4118967

Admin

Field

Extended Archiver

Description

Extended Archiver is a troubleshooting tool that enables you to collect logs covering an extended period of time. Before using it, contact your authorized AirLink reseller or Sierra

Wireless representative to discuss the problem.

To start the process:

Click Extended Archiver.

Select the following options, as advised by Sierra Wireless:

•

The number of times to run the archiver (1–25; default is 16)

•

The interval between runs (30 minutes, 1 hour, 1.5 hours, 2 hours, 2.5 hours, 3 hours, 3.5 hours, 4 hours, 4.5 hours, 5 hours, 5.5 hours, 6 hours, or 6.5 hours; default is 1.5 hours)

Click Start.

The Extended Archiver saves the current set of logs. It waits for the configured interval and then collects another set of logs, which are saved to the same file. This process continues for the number of times the Archiver is configured to run.

At any time, you can click Save Archive. The logs collected to that point are saved and the process continues.

Reset to Factory

Default

Once the process is complete, click Save Archive, save the tarred gzip file (file extension .tgz) to your computer, and email it to your support contact.

Stopping and Restarting the Extended Archiver

After you click the Start button, it changes to Stop. To stop the process:

Click Save Archive if you want to save the logs already collected.

Click Stop. Logs not already saved will be lost. If desired, you can change the settings and restart the process.

Note: The Extended Archiver settings and the collected logs persist over reboots. Once the reboot is complete, the process resumes.

Erases all customer-defined settings, including custom APNs and resets all settings

(passwords, LAN and WAN configuration, security settings, ALEOS Applications

Framework, etc.) to the original factory settings. ALEOS AF is also reset to disabled.

Rev 4 Jun.16

293

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Field

Reset Mode

Description

Before resetting the AirLink gateway to the factory default settings, you can choose to preserve the configured network connection settings. Options are:

•

Reset All—All settings including network settings are returned to the factory default values on Reset to Factory Default.

•

Preserve Cellular Authentication Settings—(default) When the device is returned to factory default settings (either by clicking the Reset to Factory Defaults button in

ACEmanager, or pressing the hardware reset button as described in the Hardware

User Guide), the following network settings are preserved:

•

Network User ID

•

Network Password

•

Network Authentication Mode

•

LTE Authentication Mode

•

APN Type

•

Select from the List (APN value)

•

User Entered APN

•

Backup APN

•

Backup Network Authentication Mode

•

Backup LTE Authentication Mode

•

Backup Network User ID

•

Backup Network Password

•

SIM Card Pin code

•

Status of the last PIN lock/unlock attempt

•

ALMS Enabled/Disabled status

•

ALMS Name (Device name in ALMS)

•

Device Initiated Interval (ALMS)

•

ALMS Server URL

•

Reset Mode

•

Network Operator Switching configuration and stored radio module firmware

294 4118967

Field

Mark

Admin

Description

This button is used to mark the start of a section in the device log and is typically used for troubleshooting. If asked to do so:

Click the Mark button and enter the text you want to appear in the log file.

Alphanumeric characters, spaces, periods, commas, dashes, colons and semi-colons are allowed.

Diagnostic shell access

Click Mark Now.

Proceed with the configuration changes.

Generate a log file. (See

Log on page 296.)

When enabled, this field allows Sierra Wireless TechSupport personnel to locally access the diagnostic shell on your gateway. It should be left at the default setting unless Sierra

Wireless TechSupport asks you to change it.

Radio Passthru

Radio Passthru allows a direct connection, using USB, to the internal radio.

Normal cellular radio operation is suspended while Radio Passthru is enabled.

Radio Passthru is generally used only in certain troubleshooting scenarios.

The hardware bypass remains in effect until the gateway is rebooted.

Note: Because Radio Passthru is not USB/net or USB/serial, a different set of drivers are required to connect to the radio installed inside an AirLink gateway. Additionally, while it is possible to send AT commands to the radio using a terminal connection, there are software applications designed to communicate with the radio directly. If you need to use Radio

Passthru, contact your Sierra Wireless AirLink representative to obtain the needed drivers and/or software application.

Rev 4 Jun.16

295

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Figure 14-4: ACEmanager: Admin > Radio Passthru

Log

The Log file is a system log of the AirLink gateway.

The Logging configuration screen enables you to configure log verbosity and display filtering. The View Log screen enables you to view and save logs. The logs are in plain text.

To configure what you want to include in the logs:

In ACEmanager, go to Admin > Log.

296

Figure 14-5: ACEmanager: Admin > Log, Configure Logging

4118967

Rev 4 Jun.16

Admin

For each subsystem listed:

Select whether or not to display it in the log.

Separate filters, based on subsystem and severity, are applied when the messages are generated and when the messages are displayed. Six severity levels are supported for filtering in the drop-down lists for verbosity:

· Critical

· Error

· Warning

· Notice

· Info (information)

· Debug

Note: The VPN Sub System only allows for Info and Debug. For maximum information, set the VPN verbosity to Debug.

b. Select the verbosity level.

Note: Some log messages are only displayed if you display Linux Syslog. For example, If you are debugging a VPN or LAN setup, the relevant information is only displayed in the

Linux Syslog.

Optional: To display Linux Syslog:

Ensure that Display (default value) is selected the drop-down menu beside Linux Syslog.

Click Apply.

If you have changed any of the verbosity levels or the Linux syslog setting:

Reboot the AirLink gateway.

b. Log into ACEmanager, go to Admin > Log.

Select View Logs from the menu on the left side of the page.

297

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

298

Figure 14-6: ACEmanager: Admin > Log, View Log

Note: VPN info and debug information uses the term racoon (rather than VPN).

Note: If you toggle the “Display in Log?” field, clear and refresh the View Log page. (You do not need to reboot the device.)

Tip:

Use View Log for troubleshooting purposes (e.g., when setting up the IPsec configuration). The Log page allows you to establish the tunnel connection and monitor the results directly. To change the intervals at which the log is displayed, you can change the settings in Auto Refresh.

Actions on the View Log screen include:

•

Auto Refresh — The drop-down menu allows you to set up an automatic log page refresh, and the interval between refreshes: 30 secs, 1 minute, or

2 minutes.

•

Refresh button — Initiates a manual page refresh

•

Clear button — Clears out the tunnels

•

Save button — Creates a text file of the log

4118967

Radio Module Firmware

Admin

Rev 4 Jun.16

Figure 14-7: ACEmanager: Admin > Radio Module Firmware

AirLink gateways come preloaded with multiple versions of radio module firmware. When the gateway is powered on, the gateway checks the stored radio module firmware versions and automatically loads the appropriate version for the installed primary SIM card onto the radio module.

This feature, which is intended for North American products, makes it easy to provision the gateway for a particular mobile network. To provision the gateway:

Obtain an account and SIM card for the mobile network you want to run the gateway on.

Insert the SIM card into the primary SIM card slot. (For instructions on installing the SIM card, refer to the Hardware User Guide for your gateway.)

Power on the gateway. It chooses the appropriate radio module firmware to use for the installed SIM card, provided it is stored on the gateway.

If the appropriate firmware is not stored on the gateway, you can download it from source.sierrawireless.com

and install it on the gateway. You can also:

•

Check which version of radio module firmware is currently active

•

Remove radio module firmware from the gateway

•

Update the radio module firmware stored on the gateway

•

Override the automatic function and manually select the radio module firmware to be used

Note: You can store a maximum of six radio module firmware version on the gateway.

Note: If you select Preserve Cellular Authentication Settings in the

Reset Mode

field before rebooting the gateway, the configuration and the stored radio module firmware are preserved when you reset the gateway to the factory default settings.

299

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

To manage radio module firmware:

In ACEmanager, go to Admin > Radio Module Firmware.

Figure 14-8: ACEmanager: Admin > Radio Module Firmware

Use the information in the following table to install, update, or remove radio module firmware.

Field Description

Active?

Indicates whether or not the radio module firmware is currently in use

Network Operator

Indicates the Mobile Network Operator associated with the radio module firmware

Version

Indicates the version number of the radio module firmware

Up to date?

Actions

Indicates if the firmware in use matches the ALEOS-referenced radio module firmware

Action buttons beside each radio module firmware listed, enable you to:

•

Update—Click to update the radio module firmware for that RMID. Updating the active radio module firmware updates the version in storage and also updates the firmware on the radio module itself.

•

Remove—Click to remove that radio module firmware from the gateway storage

Note: The firmware cannot be removed if it is the active firmware.

•

Activate—Click to select a radio module firmware to be the active firmware for the gateway.

This option is only available if

Network Operator Switching is set to Disable. See Manually

Selecting the Radio Module Firmware .

You can also:

•

Install—Click to add an additional radio module firmware image to the gateway storage.

When the maximum number of radio module firmware versions are stored on the gateway, the Install button is not available. To free up space to add another version, first remove one of the firmware versions on the gateway.

300 4118967

Admin

Field Description

Network Operator

Switching

Enable or disable Network Operator Switching

•

Enable—When the gateway powers on or reboots, it automatically selects and uses the appropriate radio module firmware for the installed primary SIM card, if it is stored on the gateway. If there is no SIM card installed in the primary SIM card slot, the gateway switches to the SIM card in the secondary SIM card slot. (default)

•

Disable—The gateway does not automatically select the appropriate radio module firmware when it is powered on or rebooted. You can manually select the firmware to use.

See Manually Selecting the Radio Module Firmware .

ALMS Radio

Module Firmware

Update

Enables you to choose which radio module firmware ALMS will update when you update

ALEOS:

•

Update Current Only—Only the radio module firmware in use is updated, if required

(default)

•

Update All—All the radio module firmware stored on the gateway is updated, if required

Manually Selecting the Radio Module Firmware

To manually select the radio module firmware to use:

In ACEmanager, go to Admin > Radio Module Firmware.

Rev 4 Jun.16

Figure 14-9: ACEmanager: Admin > Radio Module Firmware

In the SIM Based Radio Module Image switching field (under Options), select

Disable.

Under Firmware, click Activate beside the firmware you want the gateway to use.

Click Apply.

Click reboot or press and release the reset button on the gateway.

301

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

302 4118967

Rev 4 Jun.16

A: Windows Dial-up Networking (DUN)

Dial-up Networking (DUN) enables you to use Point-to-Point Protocol

(PPP) to establish a connection between a host PC serial port and the AirLink gateway.

Internet

PPP connection

Serial cable

Host PC

Figure A-1: PPP connection

AirLink gateway

WAN connection

Caution:

To install any driver on your computer, you may need to be logged in as Administrator or have Administrator privileges for your login.

Microsoft Windows 7 is used in the examples below. The device driver installation and DUN setup and configuration is similar in other

Microsoft Windows operating systems, including Windows XP and

Windows CE.

Note: If your device is new, or has recently been reset to factory default settings, ensure that the device has been on air at least once before being used with a DUN connection.

Installing a Device Driver

Connect the AirLink gateway

Connect the device to the computer with a DB-9 cable from one

RS-232 port to the other.

Go to Serial > Port Configuration.

Set the DB9 Serial Echo field to Disable.

Reboot.

Note: You need to set the DB9 Serial Echo field echo to Disable any time you want to set up a PPP connection.

303

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Install the driver

Select Start > Control Panel > Phone and Modem Options.

Figure A-2: Phone and Modem Options

Select the Modems tab.

304

Figure A-3: Phone and Modem Options: devices

4118967

Rev 4 Jun.16

Click Add.

Windows Dial-up Networking (DUN)

Figure A-4: Add Hardware Wizard

Select Don’t detect my modem; I will select it from a list.

Click Next.

305

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

306

Figure A-5: Add Hardware Wizard: Install New Modem

Under Manufacturer, select (Standard Modem Types).

Under Models, select Standard 33600 bps Modem.

Tip:

If you have the speed for your device configured as something other than the default, use the Standard device that matches the speed you configured.

Click Next.

4118967

Rev 4 Jun.16

Windows Dial-up Networking (DUN)

Figure A-6: Add Hardware Wizard: Select Ports

Select Selected Ports.

10. Select the COM port the device is connected to (commonly COM1).

11. Click Next.

307

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Figure A-7: Add Hardware Wizard: Finish

12. Once the device driver is installed, click Finish.

When you return to the Phone and Modem Options page, you should see the newly installed device “attached to” the correct COM port.

308

Figure A-8: Phone and Modem Options > Modems

13. Highlight the modem, and click Properties. The following window appears:

4118967

Windows Dial-up Networking (DUN)

Figure A-9: Modem Properties

14. Select the Modem tab.

Rev 4 Jun.16

Figure A-10: Modem Properties > Modem

15. Confirm that the Maximum Port Speed is set to 115200 (default).

309

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

16. Click OK to exit.

17. Click OK again to exit out of the Phone and Modem Options.

18. Go to Start > Control Panel > Device Manager.

310

Figure A-11: Device Manager

19. Under Modems, highlight Standard 33600 bps Modem. Right-click and select

Update Driver Software....

4118967

Windows Dial-up Networking (DUN)

Figure A-12: Update Driver Software—Browse

20. Select Browse my computer for driver software.

Rev 4 Jun.16

Figure A-13: Update Driver Software—Let me pick...

311

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

21. Select Let me pick from a list of device drivers on my computer.

Figure A-14: Update Driver Software—Select Standard Modem

22. Deselect Show compatible hardware.

23. Under Manufacturer, select (Standard Modem Types).

24. Under Models, select Standard Modem.

25. Click Next.

If you see an Update Driver Warning, click Yes.

312

Figure A-15: Update Driver Software—Warning

The software driver updates and the following window appears:

4118967

Windows Dial-up Networking (DUN)

Rev 4 Jun.16

Figure A-16: Update Driver Software—Success

26. Click Close.

Creating a Dial-Up Networking (PPP)

Connection

Once you have the driver for the modem installed on your computer, you can set up and configure Dial Up Networking (DUN).

Note: No other device or program can use the COM port (serial port) configured for the modem driver while the DUN session is active.

Caution:

If you have an existing LAN connection, installing DUN for the AirLink gateway may interfere with the LAN connection. We recommend disconnecting your LAN connection before using a PPP connection with your AirLink gateway.

Once you have configured the DUN connection on your computer:

•

The DUN connection may be set as the default connection.

•

The computer may be configured to dial the DUN connection when it cannot detect any network connection.

For instructions on changing these options, see

Connection settings on page 321.

313

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

If you are using a DUN connection with any other network connection (such as

Ethernet), you may need to use the route command in Windows to set up a static route through the device to access the location remotely over the PPP link and the mobile network. This guide does not provide information on the route command. Consult your network administrator for information on properly configuring routing.

Create a new network connection.

Select Start > Control Panel > Network and Sharing Center.

314

Figure A-17: Network and Sharing Center Window

Select Set up a new connection or network.

4118967

Windows Dial-up Networking (DUN)

Figure A-18: Set up a Connection or Network

Select Set up a dial-up connection.

Click Next.

If you are asked which modem you want to use, select Standard Modem.

Rev 4 Jun.16

Figure 1-19: Create a Dial up Connection

315

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

In the Dial-up phone number field, type “#777”.

Ignore the User name and Password fields.

In the Connection name field, type “ALEOS Dial-up Connection” or other desired name.

Click Connect.

Alternatively, to connect to the ALEOS Dial-up network:

Click the network connection icon

in the system tray.

b. Select ALEOS Dial-up Connection.

Click Connect.

Configure the DUN connection

After you complete the New Connection Wizard:

Click the network connection icon, select ALEOS Dial-up Connection, and click Connect.

316

Figure A-20: DUN Connection

If you have a user name and password configured in ACEmanager for PPP connections, enter them in the User name and Password fields. Otherwise, leave these fields blank.

Click Properties.

1. The appearance of the connection icon varies depending on the type of connections available. For example, It may appear as

4118967

Windows Dial-up Networking (DUN)

Figure A-21: DUN Properties

Confirm that the check box beside Use dialing rules is not selected.

Click Configure... (below the Connect using box).

Rev 4 Jun.16

Figure A-22: Modem Configuration

Confirm that the Maximum speed (bps) is set to 115200.

Confirm that Enable hardware flow control is selected. Do not select any other options.

Click OK.

317

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

In the main properties window, select the Options tab.

318

Figure A-23: Networking

10. Click PPP Settings.

Figure A-24: PPP Settings

11. Clear the check boxes beside all three PPP settings.

12. Click OK.

13. Select the Networking tab.

4118967

Windows Dial-up Networking (DUN)

Rev 4 Jun.16

Figure A-25: DUN Connection > Networking tab

14. Select Internet Protocol Version 4 (TCP/IPv4) and then select Properties.

Tip:

For most configurations, getting the IP address and the DNS server address are automatic.

319

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Figure A-26: TCP/IP Properties

15. Click Advanced.

320

Figure A-27: Advanced TCP/IP

4118967

Rev 4 Jun.16

Windows Dial-up Networking (DUN)

16. Select Use default gateway on remote network.

17. Click OK.

Tip:

You may want to check the Options tab and change the settings for applications you use. The default options are generally applicable for most uses.

Caution:

Unless specifically directed to do so by Support or your network administrator, you do not need to make any changes to the options on the Security tab.

18. Click OK until you return to the Connect window.

19. Log in to ACEmanager and go to Serial > Port Configuration.

20. Under Port Configuration:

Set the Flow Control field to Hardware.

b. Set the DB9 Serial Echo field to Disable.

21. Click Apply and reboot the device.

Connection settings

To set the default connection:

Go to Start > Control Panel > Network and Sharing Center.

Select Change adapter settings.

Right-click the icon for the DUN connection.

If you want this to be your default connection, select Set as Default Connection.

If it is already the default connection and you do not want it as your default connection, select Cancel as Default Connection.

If you do not want the DUN connection to be dialed when there is no other connection:

Go to Start > Control Panel > Internet Options.

Select the Connections tab.

Highlight the DUN connection and select Never dial a connection.

Click Apply.

Click OK.

321

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

322 4118967

Rev 4 Jun.16

B: Modbus/BSAP Configuration

The AirLink gateway supports Modbus ASCII, Modbus RTU, and

BSAP, and can also emulate other protocols (like DF1) using the

Modbus Variable feature.

Modbus Overview

The Modbus Protocol provides for client-server (i.e., master-slave) communications between intelligent devices. As a de facto standard, it is the most widely used network protocol in the industrial manufacturing environment to transfer discrete/analog I/O and register data between control devices. Modbus, BSAP, and other

Modbus variations are often used in conjunction with telemetry devices.

Tip:

This section is just a brief overview of Modbus. For more information, refer to your Modbus equipment distributor or manufacturer or www.modbus.org

Telemetry

Telemetry is an mated communications process by which data is collected from instruments located at remote or inaccessible points and transmitted to receiving equipment for measurement, monitoring, display, and recording. Transmission of the information may be over physical pairs of wires, telecommunication circuits, radios, or satellites.

Remote Terminal Unit (RTU)

Modbus was originally designed to be used in a radio environment where packets were broadcast from a central station (i.e., master or host) to a group of remote units. Each remote unit, or Remote

Terminal Unit (RTU), has a hexadecimal identification number (ID).

The first part of the broadcast packet contains an RTU ID which corresponds to the ID of one of the remote units. The Modbus host looks for the ID and only sends to the unit with the matching ID; the

RTU then replies back to the central station.

The RTU connects to such physical equipment as switches, pumps, and other devices, and monitors and controls these devices. The

RTU can be part of a network set up for Supervisory Control and

Data Acquisition.

323

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Supervisory Control and Data Acquisition (SCADA)

Supervisory Control and Data Acquisition (SCADA) describes solutions across a large variety of industries and is used in industrial and engineering applications to monitor and control distributed systems from a master location. SCADA encompasses multiple RTUs, a central control room with a host computer (or network), and some sort of communication infrastructure.

SCADA allows for “supervisory” control of remote devices as well as acquiring data from the remote locations. Programmable Logic Controllers allow for a higher degree of mated SCADA.

Programmable Logic Controller (PLC)

A Programmable Logic Controller (PLC) is a small industrial computer which generally monitors several connected sensor inputs and controls attached devices (motor starters, solenoids, pilot lights/displays, speed drives, valves, etc.) according to a user-created program stored in its memory. Containing inputs and outputs similar to an RTU, PLCs are frequently used for typical relay control, sophisticated motion control, process control, Distributed Control System and complex networking.

Modbus TCP/IP

Modbus TCP/IP simply takes the Modbus instruction set and wraps TCP/IP around it. Since TCP/IP is the communications standard for the Internet and most networked computers, this provides a simpler installation. Modbus TCP/IP uses standard Ethernet equipment.

Modbus on UDP

When Sierra Wireless AirLink gateways are used in place of radios, a AirLink gateway is connected to the central station (host) and an AirLink gateway is connected to each remote unit. When the AirLink gateway is configured for

Modbus with UDP, the AirLink gateway connected to the host can store a list of IP addresses or names with matching IDs. When the host at the central station sends serial data as a poll request, the AirLink gateway at the host matches the

RTU ID to a corresponding IP of a AirLink gateway at a remote unit. A UDP packet is assembled encapsulating the RTU ID and serial data transmitted from the host. The UDP packet is then transmitted to the specific AirLink gateway at the remote unit matching the RTU ID. The remote AirLink gateway then disassembles the packet before transmitting the RTU ID and serial data to the remote unit. The remote units operate in normal UDP mode and their data is sent to the host via the remote AirLink gateway and host AirLink gateway.

324 4118967

Rev 4 Jun.16

Modbus/BSAP Configuration

Configuring AirLink gateways at the Polling

Host for Modbus on UDP

This section covers a Polling Host with standard Modbus, variations may need additional AT commands.

1. Configure the ports.

The destination port for the device at the host needs to match the device port

(*DPORT) in use on all the modems at the remote sites. For example, if the remote device’s device port (*DPORT) is “12345”, then the Modbus host device's

S53 destination port should be set to “12345”.

Take note of (or set) the Device Port setting in *DPORT to configure the destination port on the remote modems.

In ACEmanager, select UDP in the side menu. Select the appropriate MD mode from the drop down menu.

•

MD13: Modbus ASCII

•

MD23: Modbus RTU (Binary)

•

MD33: BSAP

•

MD63: Variable Modbus — individual parameters are set up manually.

If you do not have a static IP, the host device should be configured to report its current IP to a Dynamic DNS (DDNS) server with Dynamic DNS.

In the Host device’s configuration, instead of an IP address for the Addr List

(ATMLIST or ATMLISTX), substitute a single unique name for each device, i.e. remote1, remote2, etc.

When you configure Dynamic DNS for the host device, make note of your device name and domain setting in ACEmanager in the menu selection Dynamic IP to be used with the remote modems.

With names instead of IP addresses for the Address List, the host device queries the DNS server for the current IP address assigned to the specific name of a remote device to send a message corresponding to the ID.

When you use names instead of IP addresses, to ensure your modems are updated quickly with the correct IP addresses for the names, set the DNS settings as well. In ACEmanager, select DNS.

Configure *DNSUSER to the same IP address as the Dynamic DNS

(*IPMANAGER1). If your modems have dynamic IP addresses and not static

(the IP address can change when it is powered up), configure *DNSUPDATE to a low interval to allow frequent updates.

325

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Configuring Remote AirLink gateways for

Modbus with UDP

Note: With a name instead of IPs for the host device, the remote devices query the DNS server for the current IP assigned to the host device before sending data back to the host.

This section covers standard Modbus settings for the AirLink gateway at the remote unit; variations may need additional commands.

Configure the ports

In ACEmanager, select Port Configuration in the side menu.

The destination port for the device at the host needs to match the device port in use on all the devices at the remote sites. For example, if the remote device’s device port (see below) is “12345”, then the Modbus host device’s S53 destination port should be set to “12345”.

Set the destination port (S53) to match the device port of the host device

(*DPORT). Make sure the device port of the remote device (*DPORT) matches the destination port of the host device (S53).

Configure IP Addresses for the Host

If the Host device has a static IP address, enter it in the Destination Address for

S53.

If the device at the host has a dynamic IP and is using Dynamic DNS, instead of an IP address for S53, specify the name of the host device (**). If the remote devices are using a different DDNS than the host device, you need to specify the fully qualified domain name (**+*DOMAIN).

Note: Setting the Host device IP address as the S53 Destination Address provides a low level security. The device does not forward UDP traffic unless the source IP/port matches what is in S53. However, if you set *AIP=1, the device forwards UDP traffic from any source IP address as long as it is accessing the device on the configured *DPORT.

Configure the default mode for start-up.

Each device at the remote locations needs to be configured to communicate with the device at the host. In ACEmanager, select UDP in the side menu.

Enable S82, UDP answer.

b. Set S83 to the idle time-out applicable to your application, commonly 20.

Configure other RTU settings.

Other parameters may need to be changed, but this is dependent on the RTU type being used. At a minimum, this typically involves setting the proper serial settings to match your RTU.

Optional: Dynamic IP Address

If you do not have a static IP, the host device should be configured to report its current IP to a Dynamic DNS (DDNS) server with Dynamic DNS.

Match the name of the device to the names specified in the host device’s MLIST or MLISTX for the connected RTU.

326 4118967

Modbus/BSAP Configuration

When you configure Dynamic DNS for the host device, note your device name and domain setting in ACEmanager in the menu selection Dynamic IP to be used with the remote devices.

When you use names instead of IP addresses, to ensure your devices are updated quickly with the correct IP addresses for the names, set the DNS settings as well.

Configure *DNSUSER to the same IP address as the Dynamic DNS

(*IPMANAGER1). If your devices have dynamic IP addresses and not static (the

IP address can change when it is powered up), configure *DNSUPDATE to a low interval to allow frequent updates.

Rev 4 Jun.16

327

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

328 4118967

Rev 4 Jun.16

C: SNMP: Simple Network Management

Protocol

Management Information Base

(MIB)

ALEOS includes a Management Information Base (MIB) that contains information specific to the AirLink gateway. Reports based on this database are sent in a form designed to be parsed by the

NMS. The data is hierarchical with entries addressed through object identifiers.

The MIB complies with:

•

RFC 1213 and MIB-II

•

RFC 2665 — Ethernet-Like Interface Types

•

RFC 2863 — The Interfaces Group MIB

SNMP Traps

SNMP traps are alerts that can be sent from the managed device to the Network Management System when an event happens. Your

AirLink gateway is capable of sending traps when the network connection becomes available.

To send SNMP traps:

In ACEmanager, go to Services > Management (SNMP).

Configure the fields under Trap Server User. (For more information, see

Management (SNMP) on page 192.)

Go to Events Reporting > Actions.

In the Action Type field select SNMP trap. (For more information,

see SNMP TRAP on page 236.)

Go Events Reporting > Events and configure monitoring for the event type that will trigger the SNMP trap. For example, the event type could be RSSI, thresholds, network state, hardware temperature, etc.

Sierra Wireless MIB

This section show the contents of the Sierra Wireless MIB file. When this file is loaded onto a remote SNMP client, you can query the

Sierra Wireless specific objects listed in this file.

For a text copy of this MIB file, go to source.sierrawireless.com

, and select your AirLink gateway.

329

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

SIERRA-MIB DEFINITIONS ::= BEGIN

IMPORTS

OBJECT-TYPE, NOTIFICATION-TYPE, MODULE-IDENTITY, IpAddress,

Integer32, Opaque, enterprises, Counter32, Unsigned32

FROM SNMPv2-SMI

TEXTUAL-CONVENTION, DisplayString, TruthValue

FROM SNMPv2-TC; sierrawireless MODULE-IDENTITY

LAST-UPDATED "201202290000Z"

ORGANIZATION "Sierra Wireless Inc"

CONTACT-INFO

"Sierra Wirelss Inc

DESCRIPTION

REVISION "201202290000Z"

DESCRIPTION

"This file defines the private Sierra MIB extensions."

::= { enterprises 20542 } sharks OBJECT IDENTIFIER ::= { sierrawireless 9}

-- MIB versions mibversion1 OBJECT IDENTIFIER ::= { sharks 1}

-- GUI Tabs for Sharks statustab OBJECT IDENTIFIER ::= { mibversion1 1} cellulartab OBJECT IDENTIFIER ::= { mibversion1 2} lantab OBJECT IDENTIFIER ::= { mibversion1 3} vpntab OBJECT IDENTIFIER ::= { mibversion1 4} securitytab OBJECT IDENTIFIER ::= { mibversion1 5} servicestab OBJECT IDENTIFIER ::= { mibversion1 6} gpstab OBJECT IDENTIFIER ::= { mibversion1 7} eventsreportingtab OBJECT IDENTIFIER ::= { mibversion1 8} serialtab OBJECT IDENTIFIER ::= { mibversion1 9} iotab OBJECT IDENTIFIER ::= { mibversion1 10} admintab OBJECT IDENTIFIER ::= { mibversion1 11} snmpconfig OBJECT IDENTIFIER ::= { mibversion1 12}

-- status elements home OBJECT IDENTIFIER ::= { statustab 1} cellular OBJECT IDENTIFIER ::= { statustab 2} lan OBJECT IDENTIFIER ::= { statustab 3}

330 4118967

Rev 4 Jun.16

SNMP: Simple Network Management Protocol

vpn OBJECT IDENTIFIER ::= { statustab 4} security OBJECT IDENTIFIER ::= { statustab 5} services OBJECT IDENTIFIER ::= { statustab 6} gps OBJECT IDENTIFIER ::= { statustab 7} serial OBJECT IDENTIFIER ::= { statustab 8} about OBJECT IDENTIFIER ::= { statustab 9}

-- home status elements phoneNumber OBJECT-TYPE

SYNTAX DisplayString (SIZE (10))

MAX-ACCESS read-only

STATUS current

DESCRIPTION ""

::= { home 17 } ipAddress OBJECT-TYPE

SYNTAX IpAddress

MAX-ACCESS read-only

STATUS current

DESCRIPTION ""

::= { home 301 } networkState OBJECT-TYPE

SYNTAX DisplayString

MAX-ACCESS read-only

STATUS current

DESCRIPTION ""

::= { home 259 } rssi OBJECT-TYPE

SYNTAX INTEGER(-125..-50)

MAX-ACCESS read-only

STATUS current

DESCRIPTION ""

::= { home 261 } gprsnetworkOperator OBJECT-TYPE

SYNTAX DisplayString

MAX-ACCESS read-only

STATUS current

DESCRIPTION ""

::= { home 770 } cdmanetworkOperator OBJECT-TYPE

SYNTAX DisplayString

MAX-ACCESS read-only

STATUS current

DESCRIPTION ""

::= { home 644 }

331

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

gprsECIO OBJECT-TYPE

SYNTAX DisplayString

MAX-ACCESS read-only

STATUS current

DESCRIPTION ""

::= { home 772 } cdmaECIO OBJECT-TYPE

SYNTAX DisplayString

MAX-ACCESS read-only

STATUS current

DESCRIPTION ""

::= { home 643 } powerIn OBJECT-TYPE

SYNTAX DisplayString

MAX-ACCESS read-only

STATUS current

DESCRIPTION ""

::= { home 266 } boardTemprature OBJECT-TYPE

SYNTAX INTEGER

MAX-ACCESS read-only

STATUS current

DESCRIPTION ""

::= { home 267 } networkServiceType OBJECT-TYPE

SYNTAX DisplayString

MAX-ACCESS read-only

STATUS current

DESCRIPTION ""

::= { home 264} aleosSWVer OBJECT-TYPE

SYNTAX DisplayString

MAX-ACCESS read-only

STATUS current

DESCRIPTION ""

::= { home 4 } netChannel OBJECT-TYPE

SYNTAX INTEGER

MAX-ACCESS read-only

STATUS current

DESCRIPTION ""

::= { home 260 } cellularBytesSent OBJECT-TYPE

SYNTAX INTEGER

MAX-ACCESS read-only

332 4118967

Rev 4 Jun.16

SNMP: Simple Network Management Protocol

STATUS current

DESCRIPTION ""

::= { home 283 } cellularBytesRecvd OBJECT-TYPE

SYNTAX INTEGER

MAX-ACCESS read-only

STATUS current

DESCRIPTION ""

::= { home 284 } deviceName OBJECT-TYPE

SYNTAX DisplayString

MAX-ACCESS read-only

STATUS current

DESCRIPTION ""

::= { home 1154 }

-- cellular status elements wanIP OBJECT-TYPE

SYNTAX IpAddress

MAX-ACCESS read-only

STATUS current

DESCRIPTION ""

::= { cellular 301 } electronicID OBJECT-TYPE

SYNTAX DisplayString

MAX-ACCESS read-only

STATUS current

DESCRIPTION ""

::= { cellular 10 } iccid OBJECT-TYPE

SYNTAX DisplayString

MAX-ACCESS read-only

STATUS current

DESCRIPTION ""

::= { cellular 771 } cellid OBJECT-TYPE

SYNTAX DisplayString

MAX-ACCESS read-only

STATUS current

DESCRIPTION ""

::= { cellular 773 } lac OBJECT-TYPE

SYNTAX DisplayString

MAX-ACCESS read-only

333

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

STATUS current

DESCRIPTION ""

::= { cellular 774 } imsi OBJECT-TYPE

SYNTAX DisplayString

MAX-ACCESS read-only

STATUS current

DESCRIPTION ""

::= { cellular 785 } keepAliveIpAddress OBJECT-TYPE

SYNTAX IpAddress

MAX-ACCESS read-only

STATUS current

DESCRIPTION ""

::= { cellular 1105 } keepAlivePingTime OBJECT-TYPE

SYNTAX INTEGER

MAX-ACCESS read-only

STATUS current

DESCRIPTION ""

::= { cellular 1104 } dnsServer1 OBJECT-TYPE

SYNTAX DisplayString

MAX-ACCESS read-only

STATUS current

DESCRIPTION ""

::= { cellular 1082 } dnsServer2 OBJECT-TYPE

SYNTAX DisplayString

MAX-ACCESS read-only

STATUS current

DESCRIPTION ""

::= { cellular 1083 } cellBand OBJECT-TYPE

SYNTAX DisplayString

MAX-ACCESS read-only

STATUS current

DESCRIPTION ""

::= { cellular 2056 } apn OBJECT-TYPE

SYNTAX DisplayString

MAX-ACCESS read-only

STATUS current

DESCRIPTION ""

::= { cellular 2151 }

334 4118967

Rev 4 Jun.16

wanUseTime OBJECT-TYPE

SYNTAX INTEGER

MAX-ACCESS read-only

STATUS current

DESCRIPTION ""

::= { cellular 5046 } rscp OBJECT-TYPE

SYNTAX INTEGER

MAX-ACCESS read-only

STATUS current

DESCRIPTION ""

::= { cellular 10249 } errorRate OBJECT-TYPE

SYNTAX INTEGER

MAX-ACCESS read-only

STATUS current

DESCRIPTION ""

::= { cellular 263 } bytesSent OBJECT-TYPE

SYNTAX INTEGER

MAX-ACCESS read-only

STATUS current

DESCRIPTION ""

::= { cellular 283 } bytesRecvd OBJECT-TYPE

SYNTAX INTEGER

MAX-ACCESS read-only

STATUS current

DESCRIPTION ""

::= { cellular 284 } packetsSent OBJECT-TYPE

SYNTAX INTEGER

MAX-ACCESS read-only

STATUS current

DESCRIPTION ""

::= { cellular 281 } packetsRecvd OBJECT-TYPE

SYNTAX INTEGER

MAX-ACCESS read-only

STATUS current

DESCRIPTION ""

::= { cellular 282 } prlVersion OBJECT-TYPE

SYNTAX INTEGER

SNMP: Simple Network Management Protocol

335

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

MAX-ACCESS read-only

STATUS current

DESCRIPTION ""

::= { cellular 642 } prlUpdateStatus OBJECT-TYPE

SYNTAX DisplayString

MAX-ACCESS read-only

STATUS current

DESCRIPTION ""

::= { cellular 646 } sid OBJECT-TYPE

SYNTAX INTEGER

MAX-ACCESS read-only

STATUS current

DESCRIPTION ""

::= { cellular 648 } nid OBJECT-TYPE

SYNTAX INTEGER

MAX-ACCESS read-only

STATUS current

DESCRIPTION ""

::= { cellular 649 } pnOffset OBJECT-TYPE

SYNTAX DisplayString

MAX-ACCESS read-only

STATUS current

DESCRIPTION ""

::= { cellular 650 } baseClass OBJECT-TYPE

SYNTAX DisplayString

MAX-ACCESS read-only

STATUS current

DESCRIPTION ""

::= { cellular 651 }

-- LAN status elements usbMode OBJECT-TYPE

SYNTAX DisplayString

MAX-ACCESS read-only

STATUS current

DESCRIPTION ""

::= { lan 1130 } vrrpEnabled OBJECT-TYPE

SYNTAX DisplayString

MAX-ACCESS read-only

336 4118967

Rev 4 Jun.16

SNMP: Simple Network Management Protocol

STATUS current

DESCRIPTION ""

::= { lan 9001 } lanpacketsSent OBJECT-TYPE

SYNTAX INTEGER

MAX-ACCESS read-only

STATUS current

DESCRIPTION ""

::= { lan 279 } lanpacketsRecvd OBJECT-TYPE

SYNTAX INTEGER

MAX-ACCESS read-only

STATUS current

DESCRIPTION ""

::= { lan 280 } wifipacketsSent OBJECT-TYPE

SYNTAX INTEGER

MAX-ACCESS read-only

STATUS current

DESCRIPTION ""

::= { lan 10405 } wifipacketsRecvd OBJECT-TYPE

SYNTAX INTEGER

MAX-ACCESS read-only

STATUS current

DESCRIPTION ""

::= { lan 10406 } wifiBridgeEnabled OBJECT-TYPE

SYNTAX DisplayString

MAX-ACCESS read-only

STATUS current

DESCRIPTION ""

::= { lan 10401 } wifiSecurityType OBJECT-TYPE

SYNTAX DisplayString

MAX-ACCESS read-only

STATUS current

DESCRIPTION ""

::= { lan 4509 } wifiAPStatus OBJECT-TYPE

SYNTAX DisplayString

MAX-ACCESS read-only

STATUS current

DESCRIPTION ""

::= { lan 4506 }

337

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

wifiSSID OBJECT-TYPE

SYNTAX DisplayString

MAX-ACCESS read-only

STATUS current

DESCRIPTION ""

::= { lan 4507 } wifiChannel OBJECT-TYPE

SYNTAX INTEGER

MAX-ACCESS read-only

STATUS current

DESCRIPTION ""

::= { lan 4508 }

-- VPN status elements incomingOOB OBJECT-TYPE

SYNTAX DisplayString

MAX-ACCESS read-only

STATUS current

DESCRIPTION ""

::= { vpn 3177 } outgoingOOB OBJECT-TYPE

SYNTAX DisplayString

MAX-ACCESS read-only

STATUS current

DESCRIPTION ""

::= { vpn 3178 } outgoingHostOOB OBJECT-TYPE

SYNTAX DisplayString

MAX-ACCESS read-only

STATUS current

DESCRIPTION ""

::= { vpn 3179 } vpn1Status OBJECT-TYPE

SYNTAX DisplayString

MAX-ACCESS read-only

STATUS current

DESCRIPTION ""

::= { vpn 3176 } vpn2Status OBJECT-TYPE

SYNTAX DisplayString

MAX-ACCESS read-only

STATUS current

DESCRIPTION ""

338 4118967

Rev 4 Jun.16

::= { vpn 3205 } vpn3Status OBJECT-TYPE

SYNTAX DisplayString

MAX-ACCESS read-only

STATUS current

DESCRIPTION ""

::= { vpn 3231 } vpn4Status OBJECT-TYPE

SYNTAX DisplayString

MAX-ACCESS read-only

STATUS current

DESCRIPTION ""

::= { vpn 3257 } vpn5Status OBJECT-TYPE

SYNTAX DisplayString

MAX-ACCESS read-only

STATUS current

DESCRIPTION ""

::= { vpn 3283 }

-- Security status elements dmz OBJECT-TYPE

SYNTAX DisplayString

MAX-ACCESS read-only

STATUS current

DESCRIPTION ""

::= { security 5113 } portForwarding OBJECT-TYPE

SYNTAX DisplayString

MAX-ACCESS read-only

STATUS current

DESCRIPTION ""

::= { security 5112 } portFilteringIn OBJECT-TYPE

SYNTAX DisplayString

MAX-ACCESS read-only

STATUS current

DESCRIPTION ""

::= { security 3505 } portFilteringOut OBJECT-TYPE

SYNTAX DisplayString

MAX-ACCESS read-only

STATUS current

DESCRIPTION ""

::= { security 3506 }

SNMP: Simple Network Management Protocol

339

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

trustedHosts OBJECT-TYPE

SYNTAX DisplayString

MAX-ACCESS read-only

STATUS current

DESCRIPTION ""

::= { security 1062 } macFiltering OBJECT-TYPE

SYNTAX DisplayString

MAX-ACCESS read-only

STATUS current

DESCRIPTION ""

::= { security 3509 } badPasswdCount OBJECT-TYPE

SYNTAX INTEGER

MAX-ACCESS read-only

STATUS current

DESCRIPTION ""

::= { security 385 } ipRejectCount OBJECT-TYPE

SYNTAX INTEGER

MAX-ACCESS read-only

STATUS current

DESCRIPTION ""

::= { security 386 } ipRejectLog OBJECT-TYPE

SYNTAX DisplayString

MAX-ACCESS read-only

STATUS current

DESCRIPTION ""

::= { security 387 }

-- Services status elements aceNet OBJECT-TYPE

SYNTAX DisplayString

MAX-ACCESS read-only

STATUS current

DESCRIPTION ""

::= { services 5026 } aceManager OBJECT-TYPE

SYNTAX DisplayString

MAX-ACCESS read-only

STATUS current

DESCRIPTION ""

::= { services 1149 }

340 4118967

Rev 4 Jun.16

SNMP: Simple Network Management Protocol

dynamicDnsService OBJECT-TYPE

SYNTAX DisplayString

MAX-ACCESS read-only

STATUS current

DESCRIPTION ""

::= { services 5011 } fullDomainName OBJECT-TYPE

SYNTAX DisplayString

MAX-ACCESS read-only

STATUS current

DESCRIPTION ""

::= { services 5007 }

-- GPS status elements gpsFix OBJECT-TYPE

SYNTAX INTEGER

MAX-ACCESS read-only

STATUS current

DESCRIPTION ""

::= { gps 900 } satelliteCount OBJECT-TYPE

SYNTAX INTEGER

MAX-ACCESS read-only

STATUS current

DESCRIPTION ""

::= { gps 901 } latitude OBJECT-TYPE

SYNTAX DisplayString

MAX-ACCESS read-only

STATUS current

DESCRIPTION ""

::= { gps 902 } longitude OBJECT-TYPE

SYNTAX DisplayString

MAX-ACCESS read-only

STATUS current

DESCRIPTION ""

::= { gps 903 } heading OBJECT-TYPE

SYNTAX DisplayString

MAX-ACCESS read-only

STATUS current

DESCRIPTION ""

::= { gps 904 } speed OBJECT-TYPE

341

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

SYNTAX INTEGER

MAX-ACCESS read-only

STATUS current

DESCRIPTION ""

::= { gps 905 } engineHours OBJECT-TYPE

SYNTAX INTEGER

MAX-ACCESS read-only

STATUS current

DESCRIPTION ""

::= { gps 906 }

-- Serial status elements serialPortMode OBJECT-TYPE

SYNTAX DisplayString

MAX-ACCESS read-only

STATUS current

DESCRIPTION ""

::= { serial 1043 } tcpAnswer OBJECT-TYPE

SYNTAX DisplayString

MAX-ACCESS read-only

STATUS current

DESCRIPTION ""

::= { serial 1048 } udpAnswer OBJECT-TYPE

SYNTAX DisplayString

MAX-ACCESS read-only

STATUS current

DESCRIPTION ""

::= { serial 1054 } serialPacketsSent OBJECT-TYPE

SYNTAX INTEGER

MAX-ACCESS read-only

STATUS current

DESCRIPTION ""

::= { serial 273 } serialPacketsRecvd OBJECT-TYPE

SYNTAX INTEGER

MAX-ACCESS read-only

STATUS current

DESCRIPTION ""

::= { serial 274 }

-- About status elements

342 4118967

Rev 4 Jun.16

SNMP: Simple Network Management Protocol

deviceModel OBJECT-TYPE

SYNTAX DisplayString

MAX-ACCESS read-only

STATUS current

DESCRIPTION ""

::= { about 7 } radioModelType OBJECT-TYPE

SYNTAX DisplayString

MAX-ACCESS read-only

STATUS current

DESCRIPTION ""

::= { about 9 } radioFirmwareVersion OBJECT-TYPE

SYNTAX DisplayString

MAX-ACCESS read-only

STATUS current

DESCRIPTION ""

::= { about 8 } deviceID OBJECT-TYPE

SYNTAX DisplayString

MAX-ACCESS read-only

STATUS current

DESCRIPTION ""

::= { about 25 } macAddress OBJECT-TYPE

SYNTAX DisplayString

MAX-ACCESS read-only

STATUS current

DESCRIPTION ""

::= { about 66 } aleosSWVersion OBJECT-TYPE

SYNTAX DisplayString

MAX-ACCESS read-only

STATUS current

DESCRIPTION ""

::= { about 4 } deviceHwConfiguration OBJECT-TYPE

SYNTAX DisplayString

MAX-ACCESS read-only

STATUS current

DESCRIPTION ""

::= { about 5 } msciVersion OBJECT-TYPE

SYNTAX DisplayString

343

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

MAX-ACCESS read-only

STATUS current

DESCRIPTION ""

::= { about 3 }

-- Read Write values snmpenable OBJECT-TYPE

SYNTAX INTEGER {

disabled(0),

enabled(1)}

MAX-ACCESS read-write

STATUS current

DESCRIPTION ""

::= { snmpconfig 10040 } snmpversion OBJECT-TYPE

SYNTAX INTEGER {

snmpv2c(2),

snmpv3(3)}

MAX-ACCESS read-write

STATUS current

DESCRIPTION ""

::= { snmpconfig 10041 } snmpport OBJECT-TYPE

SYNTAX INTEGER

MAX-ACCESS read-write

STATUS current

DESCRIPTION ""

::= { snmpconfig 10042 } snmpContact OBJECT-TYPE

SYNTAX DisplayString

MAX-ACCESS read-write

STATUS current

DESCRIPTION ""

::= { snmpconfig 2730 } snmpName OBJECT-TYPE

SYNTAX DisplayString

MAX-ACCESS read-write

STATUS current

DESCRIPTION ""

::= { snmpconfig 2731 } snmpLocation OBJECT-TYPE

SYNTAX DisplayString

MAX-ACCESS read-write

STATUS current

DESCRIPTION ""

::= { snmpconfig 2732 }

344 4118967

Rev 4 Jun.16

rocommunity OBJECT-TYPE

SYNTAX DisplayString

MAX-ACCESS read-write

STATUS current

DESCRIPTION ""

::= { snmpconfig 10063 } rouser OBJECT-TYPE

SYNTAX DisplayString

MAX-ACCESS read-write

STATUS current

DESCRIPTION ""

::= { snmpconfig 10045 } rosecuritylvl OBJECT-TYPE

SYNTAX INTEGER {

noauthnopriv(0),

authnopriv(1),

authpriv(2)}

MAX-ACCESS read-write

STATUS current

DESCRIPTION ""

::= { snmpconfig 10046 } roauthtype OBJECT-TYPE

SYNTAX INTEGER {

md5(0),

sha(1) }

MAX-ACCESS read-write

STATUS current

DESCRIPTION ""

::= { snmpconfig 10047 } roauthkey OBJECT-TYPE

SYNTAX DisplayString

MAX-ACCESS read-write

STATUS current

DESCRIPTION ""

::= { snmpconfig 10048 } roprivtype OBJECT-TYPE

SYNTAX INTEGER {

aes(0),

des(1) }

MAX-ACCESS read-write

STATUS current

DESCRIPTION ""

::= { snmpconfig 10049 } roprivkey OBJECT-TYPE

SYNTAX DisplayString

SNMP: Simple Network Management Protocol

345

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

MAX-ACCESS read-write

STATUS current

DESCRIPTION ""

::= { snmpconfig 10050 } rwcommunity OBJECT-TYPE

SYNTAX DisplayString

MAX-ACCESS read-write

STATUS current

DESCRIPTION ""

::= { snmpconfig 10064 } rwuser OBJECT-TYPE

SYNTAX DisplayString

MAX-ACCESS read-write

STATUS current

DESCRIPTION ""

::= { snmpconfig 10051 } rwsecuritylvl OBJECT-TYPE

SYNTAX INTEGER {

noauthnopriv(0),

authnopriv(1),

authpriv(2)}

MAX-ACCESS read-write

STATUS current

DESCRIPTION ""

::= { snmpconfig 10052 } rwauthtype OBJECT-TYPE

SYNTAX INTEGER {

md5(0),

sha(1) }

MAX-ACCESS read-write

STATUS current

DESCRIPTION ""

::= { snmpconfig 10053 } rwauthkey OBJECT-TYPE

SYNTAX DisplayString

MAX-ACCESS read-write

STATUS current

DESCRIPTION ""

::= { snmpconfig 10054 } rwprivtype OBJECT-TYPE

SYNTAX INTEGER {

aes(0),

des(1) }

MAX-ACCESS read-write

346 4118967

Rev 4 Jun.16

STATUS current

DESCRIPTION ""

::= { snmpconfig 10055 } rwprivkey OBJECT-TYPE

SYNTAX DisplayString

MAX-ACCESS read-write

STATUS current

DESCRIPTION ""

::= { snmpconfig 10056 } trapipAddress OBJECT-TYPE

SYNTAX IpAddress

MAX-ACCESS read-write

STATUS current

DESCRIPTION ""

::= { snmpconfig 1166 } trapport OBJECT-TYPE

SYNTAX INTEGER

MAX-ACCESS read-write

STATUS current

DESCRIPTION ""

::= { snmpconfig 10043 } engineid OBJECT-TYPE

SYNTAX DisplayString

MAX-ACCESS read-write

STATUS current

DESCRIPTION ""

::= { snmpconfig 10044 } trapcommunity OBJECT-TYPE

SYNTAX DisplayString

MAX-ACCESS read-write

STATUS current

DESCRIPTION ""

::= { snmpconfig 10065 } trapuser OBJECT-TYPE

SYNTAX DisplayString

MAX-ACCESS read-write

STATUS current

DESCRIPTION ""

::= { snmpconfig 10057 } trapsecuritylvl OBJECT-TYPE

SYNTAX INTEGER {

noauthnopriv(0),

authnopriv(1),

authpriv(2)}

SNMP: Simple Network Management Protocol

347

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

MAX-ACCESS read-write

STATUS current

DESCRIPTION ""

::= { snmpconfig 10058 } trapauthtype OBJECT-TYPE

SYNTAX INTEGER {

md5(0),

sha(1) }

MAX-ACCESS read-write

STATUS current

DESCRIPTION ""

::= { snmpconfig 10059 } trapauthkey OBJECT-TYPE

SYNTAX DisplayString

MAX-ACCESS read-write

STATUS current

DESCRIPTION ""

::= { snmpconfig 10060 } trapprivtype OBJECT-TYPE

SYNTAX INTEGER {

aes(0),

des(1) }

MAX-ACCESS read-write

STATUS current

DESCRIPTION ""

::= { snmpconfig 10061 } trapprivkey OBJECT-TYPE

SYNTAX DisplayString

MAX-ACCESS read-write

STATUS current

DESCRIPTION ""

::= { snmpconfig 10062 } rebootmodem OBJECT-TYPE

SYNTAX INTEGER {

nop(0),

reboot(1) }

MAX-ACCESS read-write

STATUS current

DESCRIPTION ""

::= { snmpconfig 65001 }

-- Notifications starting at 1000

348 4118967

Rev 4 Jun.16

SNMP: Simple Network Management Protocol

modemNotifications OBJECT IDENTIFIER ::= { mibversion1 1000 } value OBJECT-TYPE

SYNTAX DisplayString

MAX-ACCESS accessible-for-notify

STATUS current

DESCRIPTION

"value of MSCIID that triggered this event"

::= { modemNotifications 500 } digitalInput1 NOTIFICATION-TYPE

OBJECTS { value }

STATUS current

DESCRIPTION

"Digital Input 1 MSCIID 851"

::= { modemNotifications 1 } digitalInput2 NOTIFICATION-TYPE

OBJECTS { value }

STATUS current

DESCRIPTION

"Digital Input 1 MSCIID 852"

::= { modemNotifications 2 } digitalInput3 NOTIFICATION-TYPE

OBJECTS { value }

STATUS current

DESCRIPTION

"Digital Input 1 MSCIID 853"

::= { modemNotifications 3 } digitalInput4 NOTIFICATION-TYPE

OBJECTS { value }

STATUS current

DESCRIPTION

"Digital Input 1 MSCIID 854"

::= { modemNotifications 4 } pulseAccumulator1 NOTIFICATION-TYPE

OBJECTS { value }

STATUS current

DESCRIPTION

"Pulse Accumulator 1 MSCIID 4002"

::= { modemNotifications 5 } pulseAccumulator2 NOTIFICATION-TYPE

OBJECTS { value }

STATUS current

DESCRIPTION

349

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

"Pulse Accumulator 2 MSCIID 4003"

::= { modemNotifications 6 } pulseAccumulator3 NOTIFICATION-TYPE

OBJECTS { value }

STATUS current

DESCRIPTION

"Pulse Accumulator 3 MSCIID 4004"

::= { modemNotifications 7 } pulseAccumulator4 NOTIFICATION-TYPE

OBJECTS { value }

STATUS current

DESCRIPTION

"Pulse Accumulator 1 MSCIID 4005"

::= { modemNotifications 8 } analogInput1 NOTIFICATION-TYPE

OBJECTS { value }

STATUS current

DESCRIPTION

"Analog Input 1 MSCIID 855"

::= { modemNotifications 9 } analogInput2 NOTIFICATION-TYPE

OBJECTS { value }

STATUS current

DESCRIPTION

"Analog Input 2 MSCIID 856"

::= { modemNotifications 10 } analogInput3 NOTIFICATION-TYPE

OBJECTS { value }

STATUS current

DESCRIPTION

"Analog Input 3 MSCIID 857"

::= { modemNotifications 11 } analogInput4 NOTIFICATION-TYPE

OBJECTS { value }

STATUS current

DESCRIPTION

"Analog Input 4 MSCIID 858"

::= { modemNotifications 12 } scaledAnalogInput1 NOTIFICATION-TYPE

OBJECTS { value }

STATUS current

DESCRIPTION

"Scaled Analog Input 1 MSCIID 4041"

::= { modemNotifications 13 }

350 4118967

Rev 4 Jun.16

SNMP: Simple Network Management Protocol

scaledAnalogInput2 NOTIFICATION-TYPE

OBJECTS { value }

STATUS current

DESCRIPTION

"Scaled Analog Input 2 MSCIID 4042"

::= { modemNotifications 14 } scaledAnalogInput3 NOTIFICATION-TYPE

OBJECTS { value }

STATUS current

DESCRIPTION

"Scaled Analog Input 3 MSCIID 4043"

::= { modemNotifications 15 } scaledAnalogInput4 NOTIFICATION-TYPE

OBJECTS { value }

STATUS current

DESCRIPTION

"Scaled Analog Input 4 MSCIID 4044"

::= { modemNotifications 16 } gpsFixNotification NOTIFICATION-TYPE

OBJECTS { value }

STATUS current

DESCRIPTION

"GPS Fix MSCIID 900"

::= { modemNotifications 17 } vehicleSpeed NOTIFICATION-TYPE

OBJECTS { value }

STATUS current

DESCRIPTION

"Vehicle Speed MSCIID 905"

::= { modemNotifications 18 } engineHoursNotification NOTIFICATION-TYPE

OBJECTS { value }

STATUS current

DESCRIPTION

"Engine Hours MSCIID 906"

::= { modemNotifications 19 } headingChange NOTIFICATION-TYPE

OBJECTS { value }

STATUS current

DESCRIPTION

"Heading Change MSCIID 904"

::= { modemNotifications 20 } rssiNotification NOTIFICATION-TYPE

351

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

OBJECTS { value }

STATUS current

DESCRIPTION

"RSSI MSCIID 261"

::= { modemNotifications 21 } networkStateNotification NOTIFICATION-TYPE

OBJECTS { value }

STATUS current

DESCRIPTION

"Network State MSCIID 259"

::= { modemNotifications 22 } networkService NOTIFICATION-TYPE

OBJECTS { value }

STATUS current

DESCRIPTION

"Network Service 264"

::= { modemNotifications 23 } networkErrorRate NOTIFICATION-TYPE

OBJECTS { value }

STATUS current

DESCRIPTION

"Network Error Rate MSCIID 263"

::= { modemNotifications 24 } periodicReports NOTIFICATION-TYPE

OBJECTS { value }

STATUS current

DESCRIPTION

"Periodic Reports MSCIID 270"

::= { modemNotifications 25 } powerInNotification NOTIFICATION-TYPE

OBJECTS { value }

STATUS current

DESCRIPTION

"Power In MSCIID 266"

::= { modemNotifications 26 } boardTemp NOTIFICATION-TYPE

OBJECTS { value }

STATUS current

DESCRIPTION

"Board Temperature MSCIID 267"

::= { modemNotifications 27 } cdmaTemp NOTIFICATION-TYPE

OBJECTS { value }

STATUS current

DESCRIPTION

352 4118967

SNMP: Simple Network Management Protocol

"CDMA Temperature MSCIID 641"

::= { modemNotifications 28 } dailyDataUsage NOTIFICATION-TYPE

OBJECTS { value }

STATUS current

DESCRIPTION

"Daily Data Usage MSCIID 25001"

::= { modemNotifications 29 } monthlyDataUsage NOTIFICATION-TYPE

OBJECTS { value }

STATUS current

DESCRIPTION

"Monthly Data Usage MSCIID 25002"

::= { modemNotifications 30 }

END

Rev 4 Jun.16

353

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

354 4118967

Rev 4 Jun.16

D: AT Commands

AT Command Set Summary

Note: If you are writing software to parse AT command responses, Sierra

Wireless recommends that you design the software to be independent of the amount of whitespace. Whitespace is defined as ASCII space, tab, carriage return and linefeed characters and may appear in any combination, not necessarily containing all of the above.

Using a terminal connection (Telnet) or SSH protocol, you can send

AT commands to configure the device, command it to do something, or query a setting.

•

AT commands must always be terminated by a carriage return

<CR> (ASCII character 0x0D), i.e., pressing enter on the keyboard. Some may also include a new line or line feed <LF>.

•

If E=1 (Echo On), the AT command (including the terminating

<carriage return>) is displayed (output) before any responses.

•

Two settings affect the format of AT command output: V

(Verbose) and Q (Quiet).

•

If Q=1 (Quiet On), no result codes are output whatsoever, so there is no response generated by a (non-query) command.

•

If Q=0 (Quiet Off), result codes are output. The format of this output is then affected by the Verbose setting.

If Quiet mode is off, the result code is affected as follows:

For V=1 (Verbose mode), the textual result code is surrounded by a carriage return and new line. Any AT query response is also surrounded by a carriage return and new line.

For V=0 (Terse mode), a numeric result code is output with a single trailing carriage return (no new line is output), while any AT query response is followed by a carriage return and new line (there is no preceding output).

•

For example, possible output to the AT command “AT” with carriage return (assuming quiet mode is not on) is: carriage return — if V=0 carriage return and new line OK another carriage return and new line — if V=1

Note: AT commands work for the port on which they are executed. For example, if the user types ATE1 and then AT&W using a USB/serial port connection, it sets the USB/serial port to Echo On but not the telnet connection or the RS232 serial port.

355

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

If you need to change the port for Telnet (for example, you have the default port blocked on your firewall), the option is on the Services > Telnet/SSH tab. The default Telnet port is 2332. You can also change the Telnet timeout; if the connection is idle, default timeout is 2 minutes. This is the internal Telnet on the device to pass AT commands and not TCP PAD.

AT commands are shown in upper case, but they are not case sensitive.

This appendix organizes the commands into functional groups to allow you to more quickly locate a desired command when you know the operation but not the command. Commands under each topic are listed alphabetically.

Note: Some of the configuration commands listed here are only available as AT commands.

Reference Tables

Result codes are not shown in the command tables unless special conditions apply. Generally the result code

OK is returned when the command has been executed.

ERROR may be returned if parameters are out of range, and is returned if the command is not recognized or is not permitted in the current state or condition of the AirLink gateway.

Note: Unless otherwise stated, all commands are accessible locally and remotely.

AT command topics in this appendix:

•

Standard (Hayes) commands on page 406

•

Device Updates on page 357

•

Status on page 357

•

WAN/Cellular on page 362

•

•

•

•

•

•

•

•

Applications on page 411

•

Admin on page 415

356 4118967

AT Commands

Device Updates

Table D-1: Device Update AT Commands

Command Description

*TPLUPDATE

This AT command updates the template (configuration file) remotely.

The template file must be accessible on an FTP server.

The command parameters are:

AT*TPLUPDATE=<Server_IP>,<USER_NAME>,<PASSWORD>,<FILE_NAME> where:

•

SERVER_IP is the IP address of the FTP server.

•

USER_NAME is the user name used to access the FTP server.

•

PASSWORD is the password used to access the FTP server.

•

FILE_NAME is the name of the template file on the FTP server that you want to apply to the AirLink gateway. The template file must be stored on the FTP User_Name home, not in a sub-folder.

Example:

AT*TPLUPDATE=192.168.17.111,MyUserName,MyPassword,NewTemplate.xml

When the template is successfully applied, the message displayed is:

Template applied successfully

Note: Configure the FTP server:

•

As passive mode (not active mode)

•

To listen to port 21

Status

Table D-2: Status AT Commands

Command Description

*BAND?

*CELLINFO?

*CELLINFO2?

+CIMI?

Query the current radio module band.

To set or query the setting for RF band range or technology, see !BAND

on page 363.

Query cellular connection information.

Query in depth cell information.

HSPA and LTE only.

Query the IMSI.

Rev 4 Jun.16

357

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Table D-2: Status AT Commands (Continued)

Command Description

*DEVICEID?

When the device is configured to use the device ID with GPS reports, this command displays the 64-bit device ID created from the ESN/IMEI or phone, preceded by the hex delimiter (0x). For example: at*deviceid?

0x010112DE140B5A32

Note: If the device is not configured to use the device ID with GPS reports, the command returns “NOT SET”.

*DNS1?

*DNS2?

+ECIO?

*ETHMAC?

*ETHSTATE?

*GLOBALID?

*HOSTCOMMLVL?

+HWTEMP?

I[n]

+ICCID?

*LTERSRQ?

*LTERSRP?

*NETCHAN?

Query the primary DNS (*DNS1) and secondary (*DNS2) IP addresses.

AT*DNS1? to query DNS1

AT*DNS2? to query DNS2

Query the signal quality.

Query the MAC address of the Ethernet port

•

AT*ETHMAC? or AT*ETHMAC?1— Returns the MAC address of the main

Ethernet port

•

Query the connection state (speed and duplex) of the Ethernet port.

•

AT*ETHSTATE? or AT*ETHSTATE?1— Returns the speed and duplex state of the main Ethernet port (e.g. 100Mb/s Full Duplex)

•

Query the global ID used by ALMS to identify the device.

Query the serial host signal level.

Response example: DCD:LOW; DTR:LOW; DSR:HIGH; CTS:HIGH; RTS:LOW

Query the internal temperature of the radio module (in degrees Celsius).

Query device information.

•

n omitted—device model

•

n=0—device model

•

n=1—ALEOS software version, hardware revision, boot version

•

n=2—Radio module firmware version

•

n=3—Radio module’s unique ID (ESN, IMIEI, or EID)

HSPA and LTE only.

Query the SIM ID.

LTE only

Query the LTE signal quality (in dB).

For more information, see LTE Signal Quality (RSRQ) on page 40.

LTE only

Query the LTE signal strength (in dBm).

For more information, see LTE Signal Quality (RSRQ) on page 40.

Query the current mobile network channel.

358 4118967

AT Commands

Table D-2: Status AT Commands (Continued)

Command Description

NETIP?

Query the current WAN IP address of the device reported by the internal module

(generally obtained from your Mobile Network Operator).

If you have an Internet-routable IP address, you can use this address to contact devices from the Internet. If your device on a private mobile network, you can use this address to contact the device from another host on the same WAN network.

If required, use AT*

*NETALLOWZEROIP

to allow displaying an IP address ending in a zero.

Note: If there is no current network IP address, 0.0.0.0 is returned.

*NETOP?

*NETPHONE?

*NETRSSI?

*NETSERV?

*NETSERVICE_RAW?

Query the Mobile Network Operator of the active connection. If you are roaming, the roaming operator is returned, if the home operator allows this.

Query the device's cellular phone number, if applicable or obtainable.

Query the current RSSI (Receive Signal Strength Indicator) for non-LTE cellular connections, as a negative dBm value.

Query the current connection type (e.g., LTE, HSPA+, EV-DO Rev A, etc.).

Query the numeric value for the network service type.

•

8—2G (1x, EDGE, GPRS)

•

10—2G roaming

•

16—3G (EV-DO Rev. A, HSPA, HSPA+, UMTS)

•

18—3G roaming

•

64—4G

Rev 4 Jun.16

359

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Table D-2: Status AT Commands (Continued)

Command Description

*NETSTATE?

Query the network state of the current WAN connection.

AT*NETSTATE? returns:

•

Connecting To Network—The device is in the process of trying to connect to the mobile network.

•

Network Authentication Fail—Authentication to the mobile network has failed.

Verify settings to activate the device.

•

Data Connection Failed—The device failed to connect, and it is now waiting a set time interval before it attempts to reconnect. Verify settings to activate the device.

•

Network Negotiation Fail—Network connection negotiation failed. This is usually temporary and often clears up during a subsequent attempt.

•

Network Ready—The device is connected to the 1x mobile network and ready to send data.

•

Network Dormant—The device is connected to the 1x mobile network, but the link is dormant. It will be woken up when data is sent or received.

•

No Service—There is no mobile network detected.

•

Hardware Reset—The internal module is being reset. This is a temporary state.

•

No SIM or Unexpected SIM status—No SIM, SIM installed incorrectly, or another

SIM error.

•

Awaiting Provisioning—An EV-DO device without an account and hasn't had an account or the provisioning has been erased from the radio.

•

Provisioning... —An EV-DO device in the process of writing the account data to the radio.

•

Not Connected-Waiting for Activity — “Always On Connection” has been disabled and the device is waiting for outgoing traffic or an SMS Wakeup command to mount the PDP context. (This status applies only to International devices.)

•

Not Connected-Radio Connect off—The RADIO_CONNECT AT command was entered, and the PDP context is manually disabled. (This status applies only to

International devices.)

•

SIM Locked, but bad SIM PIN.

•

SIM PIN incorrect 3 attempts left.

•

SIM PIN incorrect 2 attempts left.

•

SIM PIN incorrect 1 attempts left.

•

SIM PIN incorrect 0 attempts left.

•

SIM Blocked, Bad unlock code.

•

SIM Blocked, unblock code incorrect.

360 4118967

AT Commands

Table D-2: Status AT Commands (Continued)

Command Description

*NETSTATE_RAW?

Query numeric value of the network state of the current WAN connection:

•

1—Connecting To Network—The device is in the process of trying to connect to the mobile network.

•

4—Network Access Denied—Connection rejected.

•

5—Network Ready—WAN is using cellular and is online.

•

7—No Service—The WAN link is down or unavailable

•

9—No SIM or Unexpected SIM status—No SIM, SIM installed incorrectly, or another SIM error.

•

11—Awaiting Provisioning—An EV-DO device without an account and hasn't had an account or the provisioning has been erased from the radio.

•

12—Data Connection Failed - Waiting to Retry—The device failed to connect, and it is waiting a set time interval before it attempts to reconnect.

•

12—Provisioning... —An EV-DO device in the process of writing the account data to the radio.

•

13—SIM Locked, but bad SIM PIN.

•

14—SIM PIN incorrect 3 attempts left.

•

15—SIM PIN incorrect 2 attempts left.

•

16—SIM PIN incorrect 1 attempts left.

•

17—SIM PIN incorrect 0 attempts left.

•

18—SIM Blocked, Bad unlock code.

•

19—SIM Blocked, unblock code incorrect.

•

30—Not Connected-Waiting for Activity — “Always On Connection” has been disabled and the device is waiting for outgoing traffic or an SMS Wakeup command to mount the PDP context. (This status applies only to International devices.)

•

31—Not Connected-Radio Connect off—The RADIO_CONNECT AT command was entered, and the PDP context is manually disabled. (This status applies only to International devices.)

+PRL?

*PRLSTATUS?

*USBNETSTATE?

*WANUPTIME?

CDMA and LTE fallback to EV-DO only

Query CDMA Preferred Roaming List (PRL) version.

CDMA only

Query the status of the most recent PRL update.

•

n=0—None (No update)

•

n=1—In progress

•

n=2—Update successful

The return of any other value indicates that the update failed.

Query the status of the USB connection.

AT*USBNETSTATE? returns:

•

None—There are no USB connections to the AirLink gateway.

•

8 MB/s Half Duplex—There is a USB connection to the device.

Query the time in minutes from which the cellular IP is obtained from the mobile network.

AT*WANUPTIME?

Rev 4 Jun.16

361

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

WAN/Cellular

A reboot is required before the WAN/Cellular AT Commands described in the following table take effect.

Table D-3: WAN / Cellular AT Commands

Command

*ACTIVESIM?

Description

Query which SIM slot contains the SIM card currently being used for the data connection.

AT*ACTIVESIM? to query

Example:

AT*ACTIVESIM?

*AUTOPRL

*AUTOPRLFREQ

Response:

•

1—The SIM card is slot 1 (upper slot) is the Active SIM.

•

2—The SIM card is slot 2 (lower slot) is the Active SIM.

CDMA only.

Query or set automatic Preferred Roaming List updates

AT*PRL? to query

AT*PRL=n to set

•

n=0—Disable

•

n=1—Enable

Note: To query the current PRL, use

+PRL?

CDMA only.

Query or set how often the PRL automatically updates.

AT*AUTOPRLFREQ? to query

AT*AUTOPRLFREQ=n to set

•

n= interval to check for updates (in days)

362 4118967

AT Commands

Table D-3: WAN / Cellular AT Commands (Continued)

!BAND

Command Description

Query or set the RF band range or technology.

AT!BAND? to query the current setting

AT!BAND=n to set at the next reboot.

The values depend on the Mobile Network Operator. For a list of bands supported in

each group, see Setting for Band on page 432.

Verizon Wireless:

•

n=00—All Bands

•

n=01—North America

•

n=02—North America, 3G

•

n=03—North America, 4G

•

n=04—World Mode

Sprint:

•

n=00—Automatic

•

n=01—LTE Only

•

n=02—CDMA Only

•

n=03—GSM Only

AT&T:

•

n=00—All Bands

•

n=01—Europe 3G

•

n=02—North America 3G

•

n=03—Europe 2G

•

n=04—North America 2G

•

n=05—GSM ALL

•

n=06—Europe

•

n=07—North America

•

n=08—WCDMA ALL

•

n=09—LTE ALL

Generic North America:

•

n=00—All Bands

•

n=01—Europe 3G

•

n=02—North America 3G

•

n=03—Europe 2G

•

n=04—North America 2G

•

n=05—GSM ALL

•

n=06—Europe

•

n=07—North America

•

n=08—WCDMA ALL

•

n=09—LTE ALL

•

n=0A— CDMA ALL

•

Rev 4 Jun.16

363

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Table D-3: WAN / Cellular AT Commands (Continued)

Command

!BAND

(continued)

International:

•

n=00—All Bands

•

n=01—Europe 3G

•

n=02—North America 3G

•

n=03—Europe 2G

•

n=04—North America 2G

•

n=05—GSM ALL

•

n=6—Europe

•

n=07—North America

•

n=08—WCDMA ALL

•

n=09—LTE ALL

Description

Note: To query the current band, use *BAND?

+CGDCONT

Note: For some Mobile Network Operator SIM Cards, you may need to set the radio band before installing the SIM card.

HSPA only

Query or set the PDP context, APN, and other information required to establish a connection to o an HSPA network. You only need to configure this once. The parameters are saved and used each time a connection is made to the HSPA network.

AT+CGDCONT? to query

AT+CGDCONT = PID,PDP_TYPE,APN [,IPADDR] to set

•

PID= PDP context identifier

•

PDP_TYPE = numeric parameter that specifies a PDP context definition

•

APN = Access Point Name

•

IPADDR = IP address

Examples:

AT+CGDCONT=1,IP,proxy

AT+CGDCONT=1,IP,internet

Note: When using the APN-related optons in ACEmanager, you generally do not need to configure +CGDCONT.

364 4118967

AT Commands

Table D-3: WAN / Cellular AT Commands (Continued)

Command

*CLIENT_PPP_AUTH

Description

Query or set the Force Network Authentication mode.

AT*CLIENT_PPP_AUTH? to query

AT*CLIENT_PPP_AUTH=n to set

•

n=0—None

•

n=1—PAP

•

n=2—CHAP

Examples:

*ATCLIENT_PPP_AUTH?

*ATCLIENT_PPP_AUTH=2

If this command is used with an AirLink RV50, the query or set applies to the Active

SIM. Use *CLIENT_PPP_AUTHSIM1 or *CLIENT_PPP_AUTHSIM2

to query or set a specific SIM card, based on the slot it is installed in.

*CLIENT_PPP_AUTHSIM1

Query or set the Force Network Authentication mode for the SIM card in Slot 1 (upper slot).

AT*CLIENT_PPP_AUTHSIM1? to query

AT*CLIENT_PPP_AUTHSIM1=n to set

•

n=0—None

•

n=1—PAP

•

n=2—CHAP

Examples:

*ATCLIENT_PPP_AUTHSIM1?

*ATCLIENT_PPP_AUTHSIM1=2

*CLIENT_PPP_AUTHSIM2

Query or set the Force Network Authentication mode for the SIM card in Slot 2 (lower slot).

AT*CLIENT_PPP_AUTHSIM2? to query

AT*CLIENT_PPP_AUTHSIM2=n to set

•

n=0—None

•

n=1—PAP

•

n=2—CHAP

Examples:

*ATCLIENT_PPP_AUTHSIM2?

*ATCLIENT_PPP_AUTHSIM2=0

Rev 4 Jun.16

365

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Table D-3: WAN / Cellular AT Commands (Continued)

+COPS

Command Description

HSPA only

Query or set the network operator and the connection mode.

AT+COPS? to query

AT+COPS=MODE[,FORMAT[,OPER]] to set

MODE

•

MODE=0 — Automatic (default)

•

MODE= 1 — Manual

•

MODE=4 — Manual/Automatic; if manual failed, it defaults to automatic

FORMAT

•

FORMAT=0 — Alphanumeric (“Name”)

•

FORMAT=2 — Numeric

OPER

•

OPER= the operator numeric code

Example, AT+COPS=1,2,302610

Manual mode, numeric format, operator code 302610

Note: On some mobile networks, explicit use of +COPS allows you to select the roaming Mobile Network Operator to use.

*EVDODATASERV

CMDA and LTE fallback to EV-DO only.

Query or set the allowable network type.

AT*EVDODATASERV? to query

AT*EVDODATASERV=n to set

•

n=0 — EV-DO Preferred — can “fall back” on CDMA/1x

(only available on EV-DO devices)

•

n=0 — LTE Preferred — can “fall back” on CDMA/EV-DO

(only available on LTE devices)

•

n=1 — EV-DO Only — fall back disabled (only available on 1x/EV-DO devices)

•

n=2 — 1x Only — EV-DO disabled (only available on 1x/EV-DO devices)

•

n=3—CDMA Only — LTE disabled (only available on LTE devices)

•

n=4—LTE Only — Fall back disabled (only available on LTE devices)

Note: If you choose one of the options where fall back is disabled and the selected network type is not available, the device will not be able to connect to the mobile network. For example, if you select LTE Only and you are in an area where there is no LTE network available, the device will not be able to connect to a mobile network until you change this setting or move to an area with LTE coverage.

366 4118967

AT Commands

Table D-3: WAN / Cellular AT Commands (Continued)

Command

*EVDODIVERSITY

Description

CDMA only. For HSPA device, see *RXDIVERSITY on page 373.

Query or set EV-DO Diversity, which allows two antennas to provide more consistent connection.

AT*EVDODIVERSITY? to query

AT*EVDODIVERSITY=n to set

•

n=0 — Disabled

•

n=1 — Enabled

Note: If you are not using a diversity antenna, *EVDODIVERSITY should be disabled.

*EVDOROAMPREF

*HANGUPTORESET

*IPPING

*IPPINGADDR

CDMA and LTE fallback to EV-DO only

Query or set the network roaming preference

AT*EVDOROAMPREF? to query

AT*EVDOROAMPREF=n to set

•

n=0—Automatic

•

n=1—Home only

HSPA only.

Query or set forcing the radio module to reset when the device disconnects.

AT*HANGUPTORESET? to query

AT*HANGUPTORESET=n to set

•

n=0—Disable

•

n=1—Enable

Query or set the interval between keepalive pings (in minutes) if no valid packets have been received by the IP address or FQDN specified in *IPPINGADDR.

AT*IPPING? to query the Keepalive PING time interval

AT*IPPING=n to set the Keepalive PING time interval

•

n=0 — Disable pinging (default)

•

n=15–255 minutes

Note: 15 minutes is the minimum interval for Keep Alive. If you set *IPPING for a value between 0 and 15, the idle interval for pings will be 15 minutes.

Query or set the Keepalive PING IP address or FQDN for the device to ping when

Keepalive Ping Time (

*IPPING ) is set.

AT*IPPINGADDR? to query

AT*IPPINGADDR=[d.d.d.d] or [n]

•

d.d.d.d=IP address

•

n=domain name

Note: AT*IPPING must to be set to a value other than 0 to enable pinging.

Rev 4 Jun.16

367

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Table D-3: WAN / Cellular AT Commands (Continued)

Command

*IPPINGFORCE

Description

Query or set the Force Keepalive Ping setting. When this feature is enabled, the

Keepalive ping is sent even if IP traffic has occurred during the configured interval.

AT*IPPINGFORCE? to query

AT*IPPINGFORCE=n to set

•

n=0—Disable

•

n=1—Enable

Note: To enable this command, *IPPING must be enabled and *IPPINGADDR configured.

*NETALLOWZEROIP

*NETAPN

Query or set allowing the device to get an IP address from the mobile network that has the last octet as 0 (zero).

AT*NETALLOWZEROIP? to query

AT*NETALLOWZEROIP=n to set

•

n=0 — Do not allow

•

n=1 — Allow

Allows the device to use a WAN IP address that ends in zero (e.g. 192.168.1.0).

HSPA and LTE fallback to HSPA only

Query or set the user entered APN.

AT*NETAPN? to query

AT*NETAPN=<apn> to set (up to 80 characters)

Examples:

AT*NETAPN?

<apn>

AT*NETAPN=<apn>

Note: When you set this command, the APN type is automatically set to User Entry so that the APN you enter with this AT command is used on reboot.

If this command is used with an AirLink RV50, the query or set applies to the Active

SIM. Use

*SIM1NETAPN

*SIM2NETAPN

to query or set a specific SIM card, based on the slot it is installed in.

368 4118967

AT Commands

Table D-3: WAN / Cellular AT Commands (Continued)

*NETPW

Command Description

Query or set the mobile network account password.

AT*NETPW? to query

AT*NETPW=<password> to set (up to 128 characters)

Note: AT*NETPW? returns asterisks (****) for privacy.

Examples:

ATNETPW?

*******

*NETPWSIM1

AT*NETPW=<password>

If this command is used with an AirLink RV50, the query or set applies to the Active

SIM. Use

*NETPWSIM1

*NETPWSIM2

to query or set a specific SIM card, based on the slot it is installed in.

Query or set the mobile network account password for the SIM card in Slot 1 (upper slot).

AT*NETPWSIM1? to query

AT*NETPWSIM1=<password> to set (up to 128 characters)

Note: AT*NETPWSIM1? returns asterisks (****) for privacy.

Examples:

ATNETPWSIM1?

*******

*NETPWSIM2

AT*NETPWSIM1=<password>

Query or set the mobile network account password for the SIM card in Slot 2 (lower slot).

AT*NETPWSIM2? to query

AT*NETPWSIM2=<password> to set (up to 128 characters)

Note: AT*NETPW? returns asterisks (****) for privacy.

Examples:

ATNETPWSIM2?

*******

AT*NETPWSIM2=<password>

Rev 4 Jun.16

369

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Table D-3: WAN / Cellular AT Commands (Continued)

Command

*NETUID

Description

Query or set the mobile network account user ID, if required.

AT*NETUID? to query

•

AT*NETUID=<uid>(up to 128 characters)

AT*NETUID?

<uid>

*NETUIDSIM1

AT*NETUID=<uid>

If this command is used with an AirLink RV50, the query or set applies to the Active

SIM. Use

*NETUIDSIM1 or *NETUIDSIM2 to query or set a specific SIM card, based

on the slot it is installed in.

Query or set the mobile network account user ID for the SIM card in Slot 1 (upper slot).

AT*NETUIDSIM1? to query

AT*NETUIDSIM1=<uid> (up to 128 characters)

Examples:

AT*NETUIDSIM1?

<uid>

*NETUIDSIM2

AT*NETUIDSIM1=<uid>

Query or set the mobile network account user ID for the SIM card in Slot 2 (lower slot).

AT*NETUIDSIM2? to query

AT*NETUIDSIM2=<uid> (up to 128 characters)

Examples:

AT*NETUIDSIM2?

<uid>

AT*NETUIDSIM2=<uid>

370 4118967

AT Commands

Table D-3: WAN / Cellular AT Commands (Continued)

Command

*NBSIMPRESENT?

Description

Query the number of SIM cards installed in the gateway.

AT*NBSIMPRESENT? to query

Example:

AT*NBSIMPRESENT?

*NWDOGTIME

PING

Response:

•

1—One SIM card installed

•

2—Two SIM cards installed

Query or set the interval that the network connection watchdog waits for a cellular

WAN connection. If no connection is established within this interval, the device resets.

AT*NWDOGTIME? to query

AT*NWDOGTIME=n to set

Accepted values:

•

n=0—Disable

•

n=5—5 Minutes

•

n=10—10 Minutes

•

n=15—15 Minutes

•

n=30—30 Minutes

•

n=45—45 Minutes

•

n=60—1 Hour

•

n=120—2 Hours (default)

•

n=180—3 Hours

•

n=240—4 Hours

Note: This AT Command replaces AT*NETWDOG.

Sends 5 PING to a single address. Returns OK if there is a response: ERROR if there is no response.

ATPING[ip address or FQDN]

Note: Do not use an equal sign (=) when issuing the command.

Example: ATPINGsierrawireless.com

Rev 4 Jun.16

371

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Table D-3: WAN / Cellular AT Commands (Continued)

Command

*PRIMARYSIM

Description

Query or set which SIM slot contains the primary SIM card. If two SIM cards are installed, the Primary SIM card is used for network connections.

*PRIMARYSIM? to query

*PRIMARYSIM=<slot number> to set

•

<slot number>=1—Primary SIM card is in slot 1 (upper slot)

•

<slot number>=2—Primary SIM card is in slot 2 (lower slot)

Examples:

AT*PRIMARYSIM?

$QCMIP

*RADIO_CONNECT

AT*PRIMARYSIM=<slot number>

The change takes effect after a reboot.

CDMA and LTE fallback to EV-DO only

Query or set use of Mobile IP (MIP) preferences.

$QCMIP? to query

$QCMIP=n to set

•

n=0—Disabled, Simple IP (SIP) only

•

n=1—Mobile IP preferred

•

n=2—Mobile IP only

This AT Command applies only to International devices on the Vodafone network.

Query or set the wireless connection setting.

AT*RADIO_CONNECT? to query

AT*RADIO_CONNECT=n to set

•

n=0—Disables data traffic. The only way to change this mode is to issue a radio_connect=1 or radio_connect=2 AT command.

•

n=1—Enables Always on connection.

•

n=2—Disables Always on connection. The device listens for outgoing traffic and establishes a mobile network data connection for a specified time:

•

When there is outgoing traffic or

•

When it receives a Wakeup SMS, provided Wakeup SMS is configured.

(Use

*TRAFWUPTOUT on page 376 to set the timeout period.)

Note: This command is not persistent over device resets.

Note: You can only send this command locally over a serial, serial USB, or local telnet/SSH connection.

372 4118967

AT Commands

Table D-3: WAN / Cellular AT Commands (Continued)

Command

*RADIO_CONNECT_

STARTUP

*RXDIVERSITY

Description

This AT Command applies only to International devices on the Vodafone network.

You can query this command remotely or locally, but it can only be set locally.

This command is the same as *RADIO_CONNECT, except

•

The change does not take effect until the next reboot.

•

The setting is persistent over subsequent reboots.

HSPA only. For CDMA devices, see

*EVDODIVERSITY on page 367.

Query or set the RX Diversity setting.

Rx Diversity allows you to use two antennas for a more consistent connection. If you are not using a diversity antenna, Rx Diversity should be disabled.

AT*RXDIVERSITY? to query

AT*RXDIVERSITY=n to set

•

n=0—Disable

•

n=1—Enable

Note: This AT Command is not available for all AirLink gateways.

*SIM1NETAPN

HSPA and LTE fallback to HSPA only

Query or set the user entered APN for the SIM card in SIM slot 1 (upper slot).

*SIM1NETAPN? to query

*SIM1NETAPN=<apn> to set the user entered APN (up to 80 characters)

Examples:

AT*SIM1NETAPN?

<apn>

AT*SIM1NETAPN=<apn>

Note: When you set this command, the APN type is automatically set to User Entry so that the APN you enter with this AT command is used on reboot.

Rev 4 Jun.16

373

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Table D-3: WAN / Cellular AT Commands (Continued)

Command

*SIM2NETAPN

Description

HSPA and LTE fallback to HSPA only

Query or set the user entered APN for the SIM card in SIM slot 2 (lower slot).

*SIM2NETAPN? to query

*SIM2NETAPN=<apn> to set the user entered APN (up to 80 characters)

Examples:

AT*SIM2NETAPN?

<apn>

*SIMPIN

AT*SIM2NETAPN=<apn>

Note: When you set this command, the APN type is automatically set to User Entry so that the APN you enter with this AT command is used on reboot.

HSPA and LTE fallback to HSPA only

Query or enter the SIM pin.

AT*SIMPIN? to query

AT*SIMPIN=<pin> to enter the SIM pin

Examples:

AT*SIMPIN?

<pin>

*SIM1PIN?

AT*SIMPIN=<pin>

If this command is used with an AirLink RV50, the query or set applies to the Active

SIM. Use

*SIM1PIN?

or *SIM2PIN?

to query or set a specific SIM card, based on the slot it is installed in

HSPA and LTE fallback to HSPA only

Query or enter the SIM PIN for the SIM card in SIM slot 1 (upper slot).

*SIM1PIN? to query

*SIM1PIN=<pin> to enter the SIM PIN

Examples:

AT*SIM1PIN?

<pin>

AT*SIM1PIN=<pin>

374 4118967

AT Commands

Table D-3: WAN / Cellular AT Commands (Continued)

Command

*SIM2PIN?

Description

HSPA and LTE fallback to HSPA only

Query or enter the SIM PIN for the SIM card in SIM slot 2 (lower slot).

*SIM2PIN? to query

*SIM2PIN=<pin> to enter the SIM PIN

Examples:

AT*SIM2PIN?

<pin>

*SIMPINENABLE

AT*SIM2PIN=<pin>

HSPA and LTE fallback to HSPA only

Query or set the status of the SIM PIN.

AT*SIMPINENABLE? to query

AT*SIMPINENABLE=<setting> to set

•

<setting>=0—Don’t change

•

<setting>=1—Enable (SIM pin required on startup)

•

<setting>=2—Disable

AT*SIMPINENABLE?

*SIM1PINENABLE

AT*SIMPINENABLE=<setting>

If this command is used with an AirLink RV50, the query or set applies to the Active

SIM. Use

*SIM1PINENABLE

*SIM2PINENABLE

to query or set a specific SIM card, based on the slot it is installed in

HSPA and LTE fallback to HSPA only

Query or set the status of the SIM PIN for the SIM card installed in SIM slot 1 (upper slot).

AT*SIM1PINENABLE? to query

AT*SIM1PINENABLE=<setting> to set

•

<setting>=0—Don’t change

•

<setting>=1—Enable (SIM pin required on startup)

•

<setting>=2—Disable

AT*SIM1PINENABLE?

AT*SIM1PINENABLE=<setting>

Rev 4 Jun.16

375

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Table D-3: WAN / Cellular AT Commands (Continued)

Command

*SIM2PINENABLE

Description

Query or set the status of the SIM PIN for the SIM card installed in SIMs slot 2 (lower slot).

AT*SIM2PINENABLE? to query

AT*SIM2PINENABLE=<setting> to set

•

<setting>=0—Don’t change

•

<setting>=1—Enable (SIM pin required on startup)

•

<setting>=2—Disable

AT*SIM2PINENABLE?

*SIM1PRESENT?

AT*SIM2PINENABLE=<setting>

Query whether or not there is a SIM card installed in SIM slot 1.

*SIM1PRESENT? to query

•

0— No SIM card in slot 1

•

1—SIM card present in slot 1

Examples:

AT*SIM1PRESENT?

*SIM2PRESENT?

*TRAFWUPTOUT

Query whether or not there is a SIM card installed in SIM slot 2.

*SIM1PRESENT? to query

•

0— No SIM card in slot 2

•

1—SIM card present in slot 2

Examples:

AT*SIM2PRESENT?

This AT Command applies only to International devices on the Vodafone network.

Query or set the timeout period after which, if there is no outgoing WAN traffic, the connection is terminated.

The timeout period only takes effect if *RADIO_CONNECT

*RADIO_CONNECT_

STARTUP

is set to 1, or Always on connection is disabled in ACEmanager. (See

Always on connection on page 62.)

AT*TRAFWUPTOUT? to query

AT*TRAFWUPTOUT=n to set

•

n=2–65535 minutes (default is 2)

Note: This timer is reset to zero each time a WAN packet goes out.

376 4118967

AT Commands

LAN

Note: A reboot is required before these commands take effect.

Table D-4: LAN AT Commands

Command Description

*DHCPHOSTEND

*DHCPNETMASK

*DHCPSERVER

Query or set the ending IP address for the Ethernet DHCP pool

AT*DHCPHOSTEND? to query

AT*DHCPHOSTEND=d.d.d.d to set

•

d.d.d.d=last IP address in Ethernet DHCP pool

Query or set the Ethernet DHCP subnet mask

AT*DHCPNETMASK? to query

AT*DHCPNETMASK=d.d.d.d to set

•

d.d.d.d=Ethernet DHCP subnet mask

Query or set the Ethernet DHCP server.

AT*DHCPSERVER? to query

AT*DHCPSERVER=n to set the DHCP server mode

•

n=0—Disable

•

n=1—Server

•

n=2—Auto

For a description of the settings, see DHCP Mode on page 97.

*DNS1?

*DNS2?

*DNSUSER

*HOSTAUTH

*HOSTPEERIP

Query the primary DNS (*DNS1) and secondary (*DNS2) IP addresses.

AT*DNS1? to query DNS1

AT*DNS2? to query DNS2

Query or set the first alternate server for DNS override. (Applies only to primary DNS.)

AT*DNSUSER? to query

AT*DNSUSER=d.d.d.d

•

d.d.d.d=IP address of domain server

Query or set the Host Authentication mode for PPPoE only. (It does not set host authentication for PPP/DUN.)

AT*HOSTAUTH? to query

AT*HOSTAUTH=n to set

•

n=0—None/Disables authentication for PPPoE (default).

•

n=1— Authentication through PAP

•

n=2—Authentication through PAP & CHAP

Query or set the IP address of the device’s Ethernet port. By default this is 192.168.13.31.

Note: Any connected LAN device can access this IP addresses, whether using a private or public IP address. This IP address must be in the same subnet as the Ethernet DHCP pool.

AT*HOSTPEERIP? to query

AT*HOSTPEERIP=d.d.d.d to set

•

d.d.d.d=local or peer IP address of the device

Rev 4 Jun.16

377

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Table D-4: LAN AT Commands (Continued)

Command Description

*HOSTPRIVIP

*HOSTPRIVMODE

*HOSTPW

Query or set the starting IP for the Ethernet DHCP pool.

AT*HOSTPRIVIP? to query

AT*HOSTPRIVIP=d.d.d.d to set

•

d.d.d.d=IP Address

Query or set the host communication mode used for tethered IP connections.

AT*HOSTPRIVMODE? to query

AT*HOSTPRIMODE=n to set which user interface uses the Public IP address

•

n=0—Ethernet Uses Public IP

•

n=1—All Hosts Use Private IPs

•

n=2—USB Uses Public IP

•

n=3—DUN Uses Public IP

•

n=4—First Host gets Public IP

Query or set the host password for PPPoE only. (It does not set the password for PPP/

DUN.)

AT*HOSTPW? to query

AT*HOSTPW=PASSWORD to set

Note: PASSWORD cannot be “password”.

*HOSTUID

*USBDEVICE

Query or set the Host user ID for PPPoE only. (It does not set the user ID for PPP/DUN.)

AT*HOSTUID? to query

AT*HOSTUID=USER ID to set (up to 64 bytes)

Note: USER ID cannot be “user”.

Query or set the startup mode for the USB port.

AT*USBDEVICE? to query

AT*USBDEVICE=n to set

•

n=0— USB Serial

•

n=1— USBNET

•

n=2— Disabled

378 4118967

AT Commands

VPN

Table D-5: VPN Commands

Command

*IPSEC1_AUTH

*IPSEC2_AUTH

*IPSEC3_AUTH

*IPSEC4_AUTH

*IPSEC5_AUTH

*IPSEC1_DH

*IPSEC2_DH

*IPSEC3_DH

*IPSEC4_DH

*IPSEC5_DH

*IPSEC1_ENCRYPT

*IPSEC2_ENCRYPT

*IPSEC3_ENCRYPT

*IPSEC4_ENCRYPT

*IPSEC5_ENCRYPT

*IPSEC1_GATEWAY

*IPSEC2_GATEWAY

*IPSEC3_GATEWAY

*IPSEC4_GATEWAY

*IPSEC5_GATEWAY

Description

Query or set the authentication type for # VPN.

AT*IPSEC[VPN number]_AUTH? to query

AT*IPSEC[VPN number]_AUTH=n to set

•

n=0 — None

•

n=1 — MD5

•

n=2 — SHA1 (default)

•

n=3 — SHA 256

Note: MD5 is an algorithm that produces a 128-bit digest for authentication. SHA is a more secure algorithm that produces both 160-bit

(SHA1) and 256-bit (SHA256) digests.

Query or set how the AirLink gateway VPN creates an SA with the VPN server. The DH (Diffie-Hellman) key exchange protocol establishes preshared keys during the phase 1 authentication. The AirLink gateway supports three prime key lengths, including Group 1 (768 bits), Group 2

(1,024 bits), and Group 5 (1,536 bits).

AT*IPSEC[VPN number]_DH? to query

AT*IPSEC[VPN number]_DH=n to set

•

n=0 — None

•

n=1 — DH1

•

n=2 — DH2 (default)

•

n=5 — DH5

Query or set the type/length of encryption key used to encrypt/decrypt

ESP (Encapsulating Security Payload) packets for # VPN.

AT*IPSEC[VPN number]_ENCRYPT? to query

AT*IPSEC[VPN number]_ENCRYPT=n to set

•

n=0 — None

•

n=1 — DES

•

n=2 — 3DES

•

n=3 — AES-128 (default)

•

n=7 — AES-256

Note: 3DES supports 168-bit encryption. AES (Advanced Encryption

Standard) supports both 128-bit and 256-bit encryption.

Query or set the IP address of the server that # VPN client connects to.

AT*IPSEC[VPN number]_GATEWAY? to query

AT*IPSEC[VPN number]_GATEWAY=[IP address] to set

Rev 4 Jun.16

379

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Table D-5: VPN Commands (Continued)

Command Description

*IPSEC1_IKE_AUTH

*IPSEC2_IKE_AUTH

*IPSEC3_IKE_AUTH

*IPSEC4_IKE_AUTH

*IPSEC5_IKE_AUTH

Query or set the IKE authentication type for # VPN.

AT*IPSEC[VPN number]_IKE_AUTH? to query

AT*IPSEC[VPN number]_IKE_AUTH=n to set

•

n=1 — MD5

•

n=2 — SHA1

•

n=3 — SHA 256

Note: MD5 is an algorithm that produces a 128-bit digest for authentication. SHA is a more secure algorithm that produces both 160-bit

(SHA1) and 256-bit (SHA256) digests.

*IPSEC1_IKE_DH

*IPSEC2_IKE_DH

*IPSEC3_IKE_DH

*IPSEC4_IKE_DH

*IPSEC5_IKE_DH

*IPSEC1_IKE_ENCRYPT

*IPSEC2_IKE_ENCRYPT

*IPSEC3_IKE_ENCRYPT

*IPSEC4_IKE_ENCRYPT

*IPSEC5_IKE_ENCRYPT

*IPSEC1_IKE_LIFETIME

*IPSEC2_IKE_LIFETIME

*IPSEC3_IKE_LIFETIME

*IPSEC4_IKE_LIFETIME

*IPSEC5_IKE_LIFETIME

*IPSEC1_LIFETIME

*IPSEC2_LIFETIME

*IPSEC3_LIFETIME

*IPSEC4_LIFETIME

*IPSEC5_LIFETIME

(1,024 bits), and Group 5 (1,536 bits).

AT*IPSEC[VPN number]_IKE_DH? to query

AT*IPSEC[VPN number]_IKE_DH=n to set

•

n=1 — DH1

•

n=2 — DH2 (default)

•

n=5 — DH5

Query or set the type/length of IKE encryption key used to encrypt/ decrypt ESP (Encapsulating Security Payload) packets for # VPN.

AT*IPSEC[VPN number]_IKE_ENCRYPT? to query

AT*IPSEC[VPN number]_IKE_ENCRYPT=n to set

•

n=1 — DES

•

n=5 — 3DES

•

n=7 — AES-128 (default)

•

n=9 — AES-256

Note: 3DES supports 168-bit encryption. AES (Advanced Encryption

Standard) supports both 128-bit and 256-bit encryption.

Query or set how long the # VPN tunnel is active (in seconds).

AT*IPSEC[VPN number]_IKE_LIFETIME? to query

AT*IPSEC[VPN number]_IKE_LIFETIME=n to set

•

n= 180–86400

•

Default is 7200.

Query or set how long the # VPN tunnel is active (in seconds).

AT*IPSEC[VPN number]_LIFETIME? to query

AT*IPSEC[VPN number]_LIFETIME=n to set

•

n= 180–86400

•

Default is 7200.

380 4118967

AT Commands

Table D-5: VPN Commands (Continued)

Command Description

*IPSEC1_LOCAL_ADDR

*IPSEC2_LOCAL_ADDR

*IPSEC3_LOCAL_ADDR

*IPSEC4_LOCAL_ADDR

*IPSEC5_LOCAL_ADDR

*IPSEC1_LOCAL_ADDR_MASK

*IPSEC2_LOCAL_ADDR_MASK

*IPSEC3_LOCAL_ADDR_MASK

*IPSEC4_LOCAL_ADDR_MASK

*IPSEC5_LOCAL_ADDR_MASK

*IPSEC1_LOCAL_ADDR_TYPE

*IPSEC2_LOCAL_ADDR_TYPE

*IPSEC3_LOCAL_ADDR_TYPE

*IPSEC4_LOCAL_ADDR_TYPE

*IPSEC5_LOCAL_ADDR_TYPE

Query or set the device subnet address for # VPN.

AT*IPSEC[VPN number]_LOCAL_ADDR? returns the device subnet address

AT*IPSEC[VPN number]_LOCAL_ADDR=[subnet address] to set

Query or set the device subnet mask information (24-bit netmask)

AT*IPSEC[VPN number]_LOCAL_ADDR_MASK? to query

AT*IPSEC[VPN number]_LOCAL_ADDR_MASK =[subnet mask] to set

Default is 255.255.255.0

*IPSEC1_LOCAL_ID

*IPSEC2_LOCAL_ID

*IPSEC3_LOCAL_ID

*IPSEC4_LOCAL_ID

*IPSEC5_LOCAL_ID

Query or set the network address type for # VPN.

AT*IPSEC[VPN number]_LOCAL_ADDR_TYPE? to query

AT*IPSEC[VPN number]_LOCAL_ADDR_TYPE=n to set

•

n=1 — Use the Host Subnet

•

n=5 — Single Address

•

n=17 — Subnet Address (default)

Query or set the local (My Identity) ID for the # VPN.

•

If IP is selected as the local (My Identity) type,

AT*IPSEC[VPN number]_LOCAL _ID? returns the WAN IP address assigned by the Mobile Network Operator

•

If FQDN or User FQDN is selected as the local (My Identity) type,

AT*IPSEC[VPN number]_LOCAL_ID? returns the FQDN (for example [email protected])

To set the local ID:

AT*IPSEC[VPN number]_LOCAL _ID=[IP address] or [FQDN], depending on the setting for Local ID (My Identity) type.

*IPSEC1_LOCAL_ID_TYPE

*IPSEC2_LOCAL_ID_TYPE

*IPSEC3_LOCAL_ID_TYPE

*IPSEC4_LOCAL_ID_TYPE

*IPSEC5_LOCAL_ID_TYPE

Query or set the local (My Identity) ID type for the # VPN.

AT*IPSEC[VPN number]_LOCAL_ID_TYPE? to query

AT*IPSEC[VPN number]_LOCAL_ID_TYPE=n to set

•

n=1 — IP

•

n=2 — FQDN

•

n=3 — User FQDN

Note:

•

IP (default) allows you to use an IP address

•

FQDN allows you to use a fully qualified domain name (FQDN) e. g., modemname.domainname.com

•

User FQDN allows you to use a user FQDN whose values should include a username (e.g. [email protected])

Rev 4 Jun.16

381

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Table D-5: VPN Commands (Continued)

Command Description

*IPSEC1_NEG_MODE

*IPSEC2_NEG_MODE

*IPSEC3_NEG_MODE

*IPSEC4_NEG_MODE

*IPSEC5_NEG_MODE

Query or set the negotiation mode for # VPN.

AT*IPSEC[VPN number]_NEG_MODE? returns

AT*IPSEC[VPN number]_NEG_MODE=n to set

•

n=1 — Main

•

n=2 — Aggressive

Note: Aggressive mode offers increased performance at the expense of security.

*IPSEC1_PFS

*IPSEC2_PFS

*IPSEC3_PFS

*IPSEC4_PFS

*IPSEC5_PFS

Query or set the Perfect Forward Secrecy (PFS) setting for # VPN.

PFS provides additional security through a DH shared secret value.

When this feature is enabled, one key cannot be derived from another.

This ensures previous and subsequent encryption keys are secure even if one key is compromised.

AT*IPSEC[VPN number]_PFS? to query PFS

AT*IPSEC[VPN number]_PFS=n to set PFS

•

n=0 — Yes (default)

•

n=1 — No

Query or set the IP address of the device behind the gateway for # VPN.

AT*IPSEC[VPN number]_REMOTE_ADDR? to query

AT*IPSEC[VPN number]_REMOTE_ADDR=[IP address] to set

*IPSEC1_REMOTE_ADDR

*IPSEC2_REMOTE_ADDR

*IPSEC3_REMOTE_ADDR

*IPSEC4_REMOTE_ADDR

*IPSEC5_REMOTE_ADDR

*IPSEC1_REMOTE_ADDR_MASK

*IPSEC2_REMOTE_ADDR_MASK

*IPSEC3_REMOTE_ADDR_MASK

*IPSEC4_REMOTE_ADDR_MASK

*IPSEC5_REMOTE_ADDR_MASK

*IPSEC1_REMOTE_ADDR_TYPE

*IPSEC2_REMOTE_ADDR_TYPE

*IPSEC3_REMOTE_ADDR_TYPE

*IPSEC4_REMOTE_ADDR_TYPE

*IPSEC5_REMOTE_ADDR_TYPE

*IPSEC1_REMOTE_ID

*IPSEC2_REMOTE_ID

*IPSEC3_REMOTE_ID

*IPSEC4_REMOTE_ID

*IPSEC5_REMOTE_ID

Query or set the remote subnet mask information (24-bit netmask).

AT*IPSEC[VPN number]_REMOTE_ADDR_MASK? to query

AT*IPSEC[VPN number]_REMOTE_ADDR_MASK =[subnet mask] to set

Default is 255.255.255.0

Query or set network information of the IPsec server behind the IPsec gateway for # VPN.

AT*IPSEC[VPN number]_REMOTE_ADDR_TYPE? to query

AT*IPSEC[VPN number]_REMOTE_ADDR_TYPE=n to set

•

n=5 — Single Address

•

n=17 — Subnet Address (default)

Query or set the remote (Peer Identity) ID for the # VPN.

•

If IP is selected as the remote (Peer Identity) type,

AT*IPSEC[VPN number]_REMOTE_ID? returns the WAN IP address assigned by the Mobile Network Operator

•

If FQDN or User FQDN is selected as the remote (Peer Identity) type, AT*IPSEC[VPN number]_REMOTE_ID? returns the FQDN (for example [email protected])

To set the remote ID:

AT*IPSEC[VPN number]_REMOTE _ID=[IP address] or [FQDN], depending on the setting for remote ID (Peer Identity) type.

382 4118967

AT Commands

Table D-5: VPN Commands (Continued)

Command Description

*IPSEC1_REMOTE_ID_TYPE

*IPSEC2_REMOTE_ID_TYPE

*IPSEC3_REMOTE_ID_TYPE

*IPSEC4_REMOTE_ID_TYPE

*IPSEC5_REMOTE_ID_TYPE

Query or set the remote (Peer Identity) ID type for the # VPN.

AT*IPSEC[VPN number]_REMOTE_ID_TYPE? to query

AT*IPSEC[VPN number]_REMOTE_ID_TYPE=n to set

•

n=1 — IP

•

n=2 — FQDN

•

n=3 — User FQDN

Note:

•

FQDN allows you to use a fully qualified domain name (FQDN) e. g., modemname.domainname.com

•

User FQDN allows you to use a user FQDN whose values should include a username (e.g. [email protected])

*IPSEC1_SHARED_KEY1

*IPSEC2_SHARED_KEY1

*IPSEC3_SHARED_KEY1

*IPSEC4_SHARED_KEY1

*IPSEC5_SHARED_KEY1

*IPSEC1_STATUS?

*IPSEC2_STATUS?

*IPSEC3_STATUS?

*IPSEC4_STATUS?

*IPSEC5_STATUS?

Query the pre-shared Key (PSK) used to initiate the # VPN tunnel.

AT*IPSEC[n]_SHARED_KEY1?

[n]=server number

*IPSEC1_TUNNEL_TYPE

*IPSEC2_TUNNEL_TYPE

*IPSEC3_TUNNEL_TYPE

*IPSEC4_TUNNEL_TYPE

*IPSEC5_TUNNEL_TYPE

Query the VPN # connection status.

AT*IPSEC[VPN number]_STATUS? to query

•

Disabled

•

Not Connected

•

Connected

Note: Use this when troubleshooting a VPN # connection.

Query or set the VPN # tunnel type.

AT*IPSEC[VPN number]_TUNNEL_TYPE? to query

AT*IPSEC[VPN number]_TUNNEL_TYPE=n to set

•

n=0 — Disable the tunnel (default)

•

n=1 — IPsec Tunnel

•

n=2 — GRE Tunnel

•

n=3 — SSL Tunnel

Note: For a successful configuration, all settings for the VPN tunnel must be identical between the AirLink gateway VPN and the enterprise

VPN server.

Rev 4 Jun.16

383

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Security

Table D-6: Security AT Commands

Command Description

F0 (F1, F2, ... F9)

Query or set the Inbound Trusted IP List.

ATF? to query the list

ATF[n]=d.d.d.d to set

•

n=0–9 Trusted IP list index number

•

d.d.d.d = IP Address

Using 255 in the IP address will allow any number

Example: 166.129.2.255 allows access by all IPs in the range 166.129.2.0–166.129.2.255.

Example: atf?

0=192.32.32.21

1=192.32.32.22

2=192.32.32.23

3=0.0.0.0

4=0.0.0.0

5=0.0.0.0

6=0.0.0.0

7=0.0.0.0

8=0.0.0.0

9=0.0.0.0

If the index number does not have an IP address associated with it, the query returns

0.0.0.0 for that index number.

Note: You can only query or configure the first nine Inbound Trusted IP addresses with this

AT Command. You cannot query or configure Trusted range entries with this AT Command.

Query or set the Inbound Trusted IP mode (Friends List) — Only allow specified IPs to access the device.

ATFM? to query the setting

ATFM=n to set

•

n=0 — Disable Trusted IP mode

•

n=1 — Enable Trusted IP mode — Only packets from IP addresses in the Trusted IP list are allowed. Packets from other IP addresses are ignored.

384 4118967

AT Commands

Services

Table D-7: Services AT Commands

Command Description

AirLink Management System

*AVMS_ENABLE

*AVMS_INTERVAL

*AVMS_NAME

*AVMS_SERVER

*AVMS_STATUS?

*AVMS_AUTOSYNC

*AVMS_VERIFYPEER

*ENGHRS

Query or set the ALMS activation status.

AT*AVMS_ENABLE? to query

AT*AVMS_ENABLE=n to set

•

n=0—Disable device initiated ALMS management

•

n=1—Enable device initiated ALMS management

Query or set the ALMS communication (heartbeat) interval in seconds.

AT*AVMS_INTERVAL? to query

AT*AVMS_INTERVAL= n to set

•

n= INTERVAL (in seconds)

Assigns or queries the name to the AirLink gateway as it appears in ALMS.

AT*AVMS_NAME? to query

AT*AVMS_NAME= n to set

•

n= ALMS NAME

Query or set the ALMS server IP address or FQDN.

AT*AVMS_SERVER? to query

AT*AVMS_SERVER=n to set

•

n=IP Address or FQDN of ALMS server

Query the ALMS connection status

Query or set ALMS autosynchronization of configuration parameters.

AT*AVMS_AUTOSYNC? to query

AT**AVMS_AUTOSYNC=n to set

•

n=0—Disable ALMS autosynchronization

•

n=1—Enable ALMS autosynchronization

Query or set peer certificate verification during SSL handshake.

AT*AVMS_VERIFYPEER? to query

AT*AVMS_VERIFYPEER=n to set

•

n=0—Disable peer certificate verification during SSL handshake

•

n=1—Enable peer certificate verification during SSL handshake

Query or set the number of hours the engine has been running.

AT*ENGHRS? to query

AT*ENGHRS=n to set

•

n= HOURS

Maximum value is 65535.

Dynamic DNS

Rev 4 Jun.16

385

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Table D-7: Services AT Commands (Continued)

Command Description

*DOMAIN

Query or set the domain name used for the IP Manager Dynamic DNS configuration.

AT*DOMAIN? to query

AT*DOMAIN=DOMAIN to set (up to 20 characters)

Example: AT*DOMAIN=eairlink.com

Tip:

Only letters, numbers, hyphens, and periods can be used in a domain name.

*DYNDNS

*IPMANAGER1

*IPMANAGER2

Note: This AT command is only usable if the Dynamic DNS Service type is set to IP Manager.

Query or set the Dynamic DNS Service type to use.

AT*DYNDNS? to query

AT*DNYDNS=n to set

•

n=0—Disable (default)

•

n=2—dyndns.org

•

n=5—noip.org

•

n=6—ods.org

•

n=8—regfish.com

•

n=9—tzo.org

•

n=10—IP Manager

Note: Only IP Manager can be fully configured using AT Commands.

Note: This AT command is only usable if the Dynamic DNS Service type is set to IP Manager.

Query or set a FQDN or IP address of the IP server to send IP change notifications to. You can configure two independent IP Manager servers.

AT*IPMANAGER[n]? to query

AT*IPMANAGER[n]=SERVER to set.

•

n=1—First IP Manager server

•

n=2—Second IP Manager server

•

SERVER = Server FQDN or IP address

Note: You can disable updates to a server by setting blank entry

(e.g., “AT*IPMANAGER1=”).

386 4118967

AT Commands

Table D-7: Services AT Commands (Continued)

Command Description

*IPMGRKEY1

*IPMGRKEY2

Note: This AT command is only usable if the Dynamic DNS Service type is set to IP Manager.

Query or set the 128-bit password/key used to authenticate the IP update notifications. If the key's value is all zeros, a default key is used. If all the bytes in the key are set to FF, then no key is used (i.e., the IP change notifications will not be authenticated).

AT*IPMGRKEY[n]? to query

AT*IPMANAGER[n]=KEY to set

•

n=1—First IP Manager server

•

n=2—Second IP Manager server

•

KEY=128-bit key in hexadecimal [32 hex characters]

*IPMGRUPDATE1

*IPMGRUPDATE2

Note: This AT command is only usable if the Dynamic DNS Service type is set to IP Manager.

Query or set the interval (in minutes) to send an IP update notification to the corresponding server. This occurs even if the IP address of the device does not change. If the value is set to 0, then periodic updates are not issued (i.e.,

IP change notifications is only be sent when the IP actually changes).

AT*IPMGRUPDATE[n] to query

AT*IPMGRUPDATE[n]=INTERVAL to set

•

n=0—Disables the update interval (updates only on changes)

•

n=1—First IP Manager server

•

n=2—Second IP Manager server

•

INTERVAL=1–255—interval (in minutes) to send an update

*MODEMNAME

Note: This AT command is only usable if AT*DYNDNS is set to 10 (IP

Manager).

Query or set the device name used by IP Manager. (This name is displayed on the Status > Home page.)

AT*MODEMNAME? to query

AT*MODEMNAME=NAME to set (up to 20 characters long)

•

NAME= device name (for example, mydevice)

The value in *DOMAIN provides the domain zone to add to this name.

Example: If *MODEMNAME=mydevice and *DOMAIN=eairlink.com, the device's fully qualified domain name is mydevice.eairlink.com.

Tip:

Each device using IP Manager needs a unique name. I.e., two devices cannot both be called “mydevice”. One could be named “mydevice1” while the other could be named “mydevice2”.

Rev 4 Jun.16

387

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Table D-7: Services AT Commands (Continued)

Command Description

SMS

*SMSM2M

*SMSM2M_8

*SMSM2M_u

You can only use these commands locally.

•

AT*SMSM2M sends an SMS in ASCII text (requires quotation marks; maximum 140 characters)

•

AT*SMSM2M_8 sends an 8-bit SMS (requires quotation marks; maximum 140 characters)

•

AT*SMSM2M_U sends a unicode SMS (requires quotation marks; maximum 140 characters)

Format:

AT*SMSM2M=“[phone] [ascii message]”

AT*SMSM2M_8=“[phone] [hex message]”

AT*SMSM2M_U=“[phone] [hex message]”

•

The phone number can only consist of numbers (NO spaces or other characters). The phone number should be as it appears in the Last

Incoming Phone Number field.

•

Example 1 (US): 14085551212 (including leading 1 and area code)

•

Example 2 (US): 4085551212 (ignore leading 1, include area code)

•

Example 3 (UK): 447786111717 (remove leading 0 and add country code)

Command Examples:

AT*SMSM2M=”18005551212 THIS IS A TEST” sends in ASCII.

AT*SMSM2M_8="17604053757 5448495320495320412054455354" sends the message “THIS IS A TEST” as 8-bit data.

AT*SMSM2M_U="17604053757

000102030405060708090a0b0c0d0e0f808182838485868788898A8b8c8d8 e8f" sends the bytes:

00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f

80 81 82 83 84 85 86 87 88 89 8a 8b 8c 8d 8e 8f

Note: Not all cellular Mobile Network Operators support 8-bit or unicode

SMS messages.

*SMS_PASSWORD

Query or set the SMS password.

AT*SMS_PASSWORD? to query

AT*SMS_PASSWORD = n n= SMS password

If no password has ever been configured, a default password is created from the last four characters of the SIM ID (for all SIM-based devices) or the ESN

(for devices without a SIM, such those using EV-DO).

Note: The configured password remains in place, even when the device is reset to factory default settings.

388 4118967

AT Commands

Table D-7: Services AT Commands (Continued)

Command Description

*SMSWUPTOUT

This AT Command only to International devices on the Vodafone network.

Query or set the connection timeout for the SMS Wakeup feature. When this feature is enabled, an IP connection is initiated on receipt of a specific type of

SMS (For information on choosing the type of SMS, see Services > SMS

>SMS Wakeup > SMS Wakeup Trigger described in step 3 on page 180

The IP connection closes after the timeout period specified in this AT command. Outgoing traffic sent after the timer is set does not reset the timer.

AT*SMSWUPTOUT? to query

AT*SMSWUPTOUT=n to set

•

n=2–65535 minutes (default is 2)

GPS

Table D-8: GPS AT Commands

Command Description

*GPSDATA?

*PGPS

*PGPSC

Query the device and provides a snap-shot of GPS data.

This command is independent of all GPS configuration. You don't need to have a server configured or any specific report type selected. The response to this command lists the fix status, satellite count, and latitude and longitude in decimal degrees. It is not formatted as a GPS report. For example:

AT*GPSDATA? returns:

GPS Fix=1

Satellite Count=8

Latitude=+49.17081

Longitude=-123.06970

Query or set the serial streaming interface ports that the reports are sent to.

AT*PGPS? to query

AT*PGPS=n to set

•

n=0—None

•

n=1—DB9 Serial

•

n=2—USB Serial

•

n=3—DB9 and USB

•

Query or set the out-of-coverage setting. This setting enables you to configure the

AirLink gateway to stream GPS reports to the serial port only when the device has no cellular coverage. (This enables you to use a back-up in-vehicle mapping application that does not rely on mobile network coverage.

AT*PGPSC? to query

AT*PGPSC=n to set

•

n=0: ALWAYS (default) GPS reports are always streamed to the serial port

•

n=1: Out of Coverage—GPS reports are only streamed to the serial port when the

AirLink gateway has no mobile network connection.

Note: The two persistent GPS report parameters, *PGPSR and *PGPSF, control the report type and message frequency of reports sent out the serial port when the AirLink gateway is out of mobile network coverage.

Rev 4 Jun.16

393

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Table D-8: GPS AT Commands (Continued)

Command Description

*PGPSD

Query or set the delay (in seconds) before the out-of-coverage stream begins sending the messages out the serial port and not into SnF.

AT*PGPSD? to query

AT*PGPSD=n to set

•

n=0 (default)

•

n=1–255

Note: Any messages put into SnF during this switch-over delay period are sent over the air when coverage is re-acquired.

*PGPSF

*PGPSR

*PPDIST

*PP2DIST

*PP3DIST

*PP4DIST

Query or set how frequently (in seconds) the GPS report is sent to the serial link.

AT*PGPSF? to query

AT*PGPSF=n to set

•

n= 0–65535

Query or set the GPS report type.

AT*PGPSR? to query

AT*PGPSR=n to set

NMEA reports:

•

n=E0—NMEA GGA + VTG

•

n=E1—NMEA GGA+VTG+RMC

•

n=E2—NMEA GGA+VTG+RMC+GSA+GSV

TAIP reports:

•

n=F0—TAIP data

•

n=F1—TAIP compact data

•

n=F2—TAIP LN report

•

n=F3—TAIP TM report

Query or set the GPS report distance interval in 100 meter units. For example, if you entered a value of 635, it would translate to 63,500 meters (63.5 kilometers).

AT*PP[Server number if other than server 1]DIST? to query

AT*PP[Server number if other than server 1]DIST=n to set

•

n=0 — Disabled

•

n=1–65535 — Distance in 100 meter units that the device moves before sending a

GPS report

394 4118967

AT Commands

Table D-8: GPS AT Commands (Continued)

Command Description

*PPDISTM

*PP2DISTM

*PP3DISTM

*PP4DISTM

Query or set the GPS report distance Interval in meters.

AT*PP[Server number if other than server 1]DISTM? to query

AT*PP[Server number if other than server 1]DISTM=n to set

•

n=0 — Disabled

•

n=40–65535—Distance in meters that the device moves before sending a GPS report

Note: If you enter a value greater than zero, but less than 40, ALEOS rounds it up to

40.

*PPDEVID

*PPFLUSHONEVT

Query or set whether or not the RAP GPS report includes device ID and if so, which type of device ID is included.

AT*PPDEVID? to query

AT*PPDEVID=n to set

•

n=0—None

•

n=1—Phone number

•

n=2—ESN/IMEI

Note: The device ID in the RAP report is in hex, not plain text.

Query or set Send SnF Buffer Immediately on input. If this feature is enabled, any pending stored reports are sent if the I/O input changes, a stationary vehicle is moved, or a maximum speed is exceeded.

AT*PPFLUSHONEVT? to query

AT*PPFLUSHONEVT=n to set

•

n=0—Disable

•

n=1—Enable

Rev 4 Jun.16

395

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Table D-8: GPS AT Commands (Continued)

Command Description

*PPGPSR

*PP2GPSR

*PP3GPSR

*PP4GPSR

*PPINPUTEVT

*PP2INPUTEVT

*PP3INPUTEVT

*PP4INPUTEVT

*PPIP

*PP2IP

*PP3IP

*PP4IP

*PPLATS

Query or set the GPS report type.

AT*PP[Server number if other than server 1]GPSR? to query

AT*PP[Server number if other than server 1]GPSR=n to set

RAP reports:

•

n=0 — Use legacy reports specified in *MF value. Note: Must also have

*PPDEVID=0.

•

n=11 — Standard GPS Report

•

n=12 — Standard GPS Report + UTC Date

•

n=13 — Standard GPS Report + UTC Date + RF data

•

n=14—Standard GPS report + GPS + Date + RF + EIO

Xora reports

•

n=D0 — Xora

NMEA reports

•

n=E0 — GGA and VTG NMEA reports

•

n=E1 — GGA, VTG and RMC NMEA reports

•

n=E2 — GGA, VTG, RMC, GSA and GSV NMEA reports

TAIP reports

•

n=F0 —TAIP data—TAIP GPS report that contains position and velocity

•

n=F1 —TAIP GPS report that contains the compact position

•

n=F2—TAIP LN report—TAIP GPS report that contains a long navigation message

•

n=F3—TAIP TM report—TAIP GPS report that contains the time and date

Query or set ability to send a special report for digital input changes.

AT*PP[Server number if other than server 1]INPUTEVT? to query

AT*PP[Server number if other than server 1]INPUTEVT=n to set

•

n=0 — Disable

•

n=1 — Enable

Query or set the IP address where GPS reports are sent. See also *PPPORT on page 398.

AT*PP[Server number if other than server 1]IP? to query

AT*PP[Server number if other than server 1]IP=d.d.d.d to set

•

d.d.d.d=IP address

Example:

AT*PPIP=192.100.100.100

Query or set the local reporting interval (in seconds).

AT*PPLATS? to query

AT*PPLATS=n to set

•

n=0—Disable (default)

•

n=1–255 (seconds)

396 4118967

AT Commands

Table D-8: GPS AT Commands (Continued)

Command Description

*PPLATSEXTRA

*PPLATSR

*PPMAXRETRIES

*PP2MAXRETRIES

*PP3MAXRETRIES

*PP4MAXRETRIES

*PPMINTIME

*PP2MINTIME

*PP3MINTIME

*PP4MINTIME

Query or set the number of additional consecutive ports that the local GPS report is sent to.

AT*PPLATSEXTRA? to query

AT*PPLATSEXTRA=n to set

•

n=0—Just the original report is sent (default).

•

n=1–7—Send GPS report copies to that number of ports.

Example: If AT*PPLATSEXTRA=7 and the port in S53 is 1000, then GPS reports will be sent to ports 1000–1008.

Query or set the GPS report type that is sent to the local client (Ethernet, USB/net, or

PPP).

AT*PPLATSR? to query

AT*PPLATSR=n to set

RAP reports:

•

n=11—GPS Data

•

n=12—GPS + Date

•

n=13—GPS + UTC + RF

•

n=14—GPS + Date + RF + EIO

NMEA reports:

•

n=E0—NMEA GGA + VTG

•

n=E1—NMEA GGA + VTG + RMC

•

n=E2—NMEA GGA + VTG + RMC + GSA + GSV

TAIP reports:

•

n=F0 —TAIP data—TAIP GPS report that contains position and velocity

•

n=F1 —TAIP GPS report that contains the compact position

•

n=F2—TAIP LN report—TAIP GPS report that contains a long navigation message

•

n=F3—TAIP TM report—TAIP GPS report that contains the time and date

Query or set maximum number retries when in Simple Reliable mode, UDP Sequence mode, and TCP transports.

AT*PP[Server number if other than server 1]MAXRETRIES? to query

AT*PP[Server number if other than server 1]MAXRETRIES=n to set

•

n=0—Disabled

•

n=1–255 retries (Maximum is 10.)

Query or set the minimum amount of time between report packets. Each packet can contain multiple reports. This is useful to limit network traffic and make more efficient use of bandwidth. You can also use it in conjunction with store and forward. The minimum value depends on the policies of the Mobile Network Operator.

AT*PP[Server number if other than server 1]MINTIME? to query

AT*PP[Server number if other than server 1]MINTIME=n to set

•

n=0—Disable

•

n=1–65535 seconds

Rev 4 Jun.16

397

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Table D-8: GPS AT Commands (Continued)

Command Description

*PPODOM

*PP2ODOM

*PP3ODOM

*PP4ODOM

*PPODOMVAL

*PPPORT

*PP2PORT

*PP3PORT

*PP4PORT

*PPREPORTINPUTS

*PP2REPORTINPUTS

*PP3REPORTINPUTS

*PP4REPORTINPUTS

*PPSIMPLETO

*PP2SIMPLETO

*PP3SIMPLETO

*PP4SIMPLETO

*PPSNF

*PP2SNF

*PP3SNF

*PP4SNF

*PPSNFR

*PP2SNFR

*PP3SNFR

*PP4SNFR

Query or set including the current odometer reading in the RAP report.

AT*PP[Server number if other than server 1]ODOM? to query

AT*PP[Server number if other than server 1]ODOM=n to set

•

n=0—Disabled (default) Do not include odometer reading in report.

•

n=1—Enabled Include odometer reading in report.

Query or set the odometer value (in meters). Maximum value is approximately 4.3 billion meters (2.7 million miles).

AT*PPODOMVAL? to query

AT*PPODOMVAL=n to set

•

n=0–4294967295 meters

Query or set the port GPS reports are sent to.

AT*PP[Server number if other than server 1]PORT? to query

AT*PP[Server number if other than server 1]PORT=n to set

•

n=0—Disable

•

n=1–65535

Query or set input reporting and including the current digital input value in RAP reports.

AT*PP[Server number if other than server 1]REPORTINPUTS? to query

AT*PP[Server number if other than server 1]REPORTINPUTS=n to set

•

n=0—Disabled

•

n=1—Enabled

Query or set the first retry interval for Simple Reliable, UDP Sequence mode, and TCP transports (in seconds).

AT*PP[Server number if other than server 1]SIMPLETO? to query

AT*PP[Server number if other than server 1]SIMPLETO=n to set

•

n=0—Disable

•

n=1–255 (Default is 10.)

Query or set the Store and Forward (SNF) setting. SNF causes GPS reports to be stored if the device/vehicle goes outside the area of network coverage. Once the vehicle is in the coverage area, the GPS reports are sent en masse to the server.

AT*PP[Server number if other than server 1]SNF? to query

AT*PP[Server number if other than server 1]SNF=n to set

•

n=0—Disabled

•

n=1—Enabled (default)

Query or set Transport /SNF mode. GPS reports are retransmitted if not acknowledged by the server.

AT*PP[Server number if other than server 1]SNFR? to query

AT*PP[Server number if other than server 1]SNFR=n to set

•

n=0—Disabled

•

n=1—Reliable mode

•

n=2—Simple Reliable mode

•

n=3—UDP Sequence

•

n=4—TCP Listen

•

n=5—TCP

398 4118967

AT Commands

Table D-8: GPS AT Commands (Continued)

Command Description

*PPTAIPID

*PPTIME

*PP2TIME

*PP3TIME

*PP4TIME

Query or set the four character alphanumeric TAIP ID.

AT*PPTAIPID? to query

AT*PPTAIPID=nnnn to set

•

nnnn=alphnumeric characters

Query or set the GPS report time interval (in seconds).

AT*PP[Server number if other than server 1]TIME? to query

AT*PP[Server number if other than server 1]TIME=n to set

•

n=0 – 65535 seconds

Note: Your cellular Mobile Network Operator may impose a minimum transmit time.

Serial

Table D-9: Serial AT Commands

Command Description

AIP

\APPP

*CTSE

DAE

*DPORT

*DU

*ENQ

Query or set the option to allow IP addresses to communicate on UDP over serial.

AT*AIP? to query

AT*AIP=n to set

•

n=0 — Allow only the IP address specified in S53 to connect when UDP auto answer is enabled (S82=2)

•

n=1 — Allow any incoming IP address to connect when UDP auto answer is enabled (S82=2)

Always subject to any security filters that may be defined. (See Security on page 384.)

Initiates a PPP connection on serial terminal.

You can also initiate a PPP connection using the ADT command and one of the supported phone numbers.

Query or set asserting Clear To Send (CTS) when there is a network coverage.

AT*CTSE? to query

AT*CTSE=n to set

•

n=0 — Disabled (default)

•

n=1 — Enable assertion of CTS when there is network coverage

Query or set AT Escape Sequence detection.

ATDAE? to query

ATDAE=n to set

•

n=0 — Enable

•

n=1 — Disable (The escape sequence (+++) is ignored.)

Query or set the device port that the device listens on for inbound packets/data/ polls.

AT*DPORT? to query

AT*DPORT=n to set

•

n=1–65535

Query or set the dial command to only use UDP.

AT*DU? to query

AT*DU=n to set

•

n=0 — Dial using the means specified (default)

•

n=1 — Dial UDP always, even when using ATDT

When this parameter is set you cannot establish a TCP PAD connection by using the

Dial command.

Query or set the option to output an ENQ [0x05] after the TCP CONNECT, delayed by the Delay Connect Response time (S221).

AT*ENQ? to query

AT*ENQ=n to set

•

n=0 — Disable (default)

•

n=1 — Enable ENQ on TCP CONNECT

400 4118967

AT Commands

Table D-9: Serial AT Commands (Continued)

Command Description

*HOSTMODE?

Query the current host mode.

AT*HOSTMODE? returns:

•

PPP

•

TCP

•

UDP

Note: If the device is not in AT mode, Telnet into the device to execute this command.

MLIST

Query or set the default start-up mode for the serial port. When the device is powercycled, the serial port enters the mode specified by this command after 5 seconds.

On startup, typing ATMD0 within 5 seconds changes the mode to normal (AT command) mode.

ATMD? to query

ATMD<hh> (hex byte) to set

•

<hh>=00 — Normal (AT Command mode)

•

<hh>=02 — PPP

•

<hh>=03 — UDP

•

<hh>=04 — TCP

•

<hh>=08 — reverse telnet/ssh

•

<hh>=13 — Modbus ASCII

•

<hh>=23 — Modbus RTU (Binary)

•

<hh>=33 — BSAP

•

<hh>=63 — Variable Modbus

•

<hh>=83 — UDP Multiple Unicast

Add IP addresses to the Modbus address list or query the Modbus address list, using decimal index values.

Format is MLISTIndex(decimal)=IP address

Example: ATMLIST10=123.123.123.123, where:

•

10 is the Index

•

123.123.123.123 is the IP address

MLISTIndex=IP to add an IP address to the list

Including the port number after the IP address is optional. If you include the port number, separate the port number and IP address by a colon.

For example: 10=123.123.123.123:11223

MLIST? to query the Modbus address list; returns the addresses in the list in the format

Index=IP. For example:

10=123.123.123.123

11=124.124.124.124

12=125.125.125.125

13=126.126.126.126

Range for index numbers is 0—65535. The Modbus address list accepts up to 100 entries.

Rev 4 Jun.16

401

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Table D-9: Serial AT Commands (Continued)

Command Description

MLISTX

Add IP addresses to the Modbus address list or query the Modbus address list, using hexadecimal index values.

Format is MLISTXIndex(hex)=IP address

Example: ATMLISTX000A=123.123.123.123, where:

•

000A is the Index

•

123.123.123.123 is the IP address

MLISTXIndex=IP to add an IP address to the list

Including the port number after the IP address is optional. If you include the port number, separate the port number and IP address by a colon.

For example: 0xA=123.123.123.123:11223

MLISTX? to query the Modbus address list returns; returns the addresses in the list in the format Index=IP. For example:

000A=123.123.123.123

000B=124.124.124.124

000C=125.125.125.125

000D=126.126.126.126

Range for index numbers is 0—FFFF. The Modbus address list accepts up to 100 entries.

MVLEN

MVMSK

Query or set the length of the Modbus Variant ID.

ATMVLEN? to query

ATMVLEN=[length of the RTU ID in bytes] to set

Query or set the Modbus Variant ID Mask (byte hex mask to use when extracting the

ID). This parameter is used when the when the Mode Default ( MD on page 401) is

set to hex 63.

ATMVMSK? to query

ATMVMSK=[byte hex mask] to set

MVOFF

MVTYP

Query or set the Modbus (Variable mode) offset in the data where the Modbus ID starts.

ATMVOFF? to query

ATMOFF=n to set

•

n= 0–255

Query or set the Modbus Variant type (RTU ID data-type in a modbus-variant

protocol). This parameter is used when MD on page 401 is set to 63. It defines the

data-type of the RTU ID in Modbus-like protocol data packets.

ATMVTYP? to query

ATMVTYP=n to set

•

n=0—Binary

•

n=1—ASCII hex

•

n=2—ASCII decimal

402 4118967

AT Commands

Table D-9: Serial AT Commands (Continued)

Command Description

IPL

Query or set the IP list dial.

AT*IPL? to query

AT*IPL=n to set

•

n=0—Disable

•

n=1—Enable

This allows you to access to the Modbus IP address list using the first two digits of the dial string.

Example: ATDT1234567 would go to ID “12” on the Modbus list and use the associated IP as the destination.

*NUMTOIP

S50

S51

S53

Query or set the option to convert a 12-digit number to an IP address

For example, converts 111222333444 to 111.222.333.444

AT*NUMTOIP? to query

AT*NUMTOIP=n to set

•

n=0—Disable

•

n=1—Enable

Query or set the data forwarding idle time-out.

ATS50? to query

ATS50=n to set

•

n=0 — a forwarding time-out of 10ms is used.

•

n= tenths of a second

Query or set the PAD data forwarding character. ASCII code of character that causes data to be forwarded. Used in UDP or TCP PAD mode.

ATS51? to query

AT51=CHARACTER to set

•

n=0 — No forwarding character

•

n= CHARACTER

Query or set the method (dial mode), destination IP address, and port used as defaults for the D (Dial) AT command.

ATS53? to query

ATS53=[method][d.d.d.d][/ppppp] to set

[method] can be:

•

P — UDP

•

T — TCP

[d.d.d.d] is the destination IP address

[pppp] is the port number.

Example:

ATS53=P111.22.33.44/5555 where:

•

The first character is the dial mode (P in this example)

•

Followed by destination IP address (111.22.33.44 in this example)

•

A slash

•

Followed by the destination port (5555 in this example)

You can also use this command to set only the port. For example, AT53=/7777.

Rev 4 Jun.16

403

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Table D-9: Serial AT Commands (Continued)

Command Description

S60

S82

S83

*SERIALLEDDISPLAY

Query or set the Telnet Client Echo Mode.

ATS60? to query

ATS60=n to set

•

n=0 — No Echo

•

n=1 — Local Echo (default)

•

n=2 — Remote Echo

Query or set UDP auto answer.

ATS82? to query

ATS82=n to set

•

n=0 — Disable

•

n=1 — Enable

Query or set the UDP auto answer idle time-out. If no data is sent or received before the time-out occurs, the current UDP session is terminated. While a session is active, packets from other IP addresses are discarded (unless *UALL is set).

ATS83? to query

ATS83=n to set

•

n=0 — No idle time-out (default)

•

n=1 – 255 — Time-out in seconds

Query or set whether or not the Activity LED on the AirLink gateway indicates traffic on the selected serial port.

AT*SERIALLEDDISPLAY? to query

AT*SERIALLEDDISPLAY=n to set

•

n=0 — LED display of serial traffic disabled (default)

•

n=1 — LED display of serial traffic enabled

For a description of the Activity LED when this parameter is enabled, see Display on page 266.

TCPS

TCPT

*UALL

Query or set the TCP connection time-out (TCPS) units. If there is no traffic through the TCP connection for the specified interval, the connection is terminated.

AT*TCPS? to query

AT*TCPS=n to set

•

n=0 — minutes

•

n=1—seconds

Query or set the interval to terminate a TCP connection when there is no traffic. This value affects only the TCP connection in TCP PAD mode.

AT*TCPT? to query

AT*TCPT=n to set

•

n=0–255

Query or set the ability to accept UDP packets from any IP address when a UDP session is active. If there is no UDP session active, an incoming UDP packet will be treated according to the UDP auto answer and AIP settings.

AT*UALL? to query

AT*UALL=n to set

•

n=0 — No effect (default)

•

n=1 — Accept UDP data from all IP addresses when in a UDP session

404 4118967

AT Commands

Table D-9: Serial AT Commands (Continued)

Command Description

*UDPLAST

*UDPPADMTU

*USD

Query or set the option to set S53 to the last accepted IP address through UDP auto answer. This can be used in conjunction with MD3 so that when there is no UDP session, new Ethernet host data will cause a connection to be restored to the last IP accepted through UDP auto answer.

AT*UDPLAST? to query

AT*UDPLAST=n to set

•

n=0 — Does not change destination IP (default)

•

n=1 — Change destination IP to last received

Query or set the size of serial MTU (PAD payload)

AT*UDPPADMTU? to query

AT*UDPPADMTU=n to set

•

n=256–4096

Query or set the specified delay before sending the UDP packets out the serial port.

AT*USD? to query

AT*USD=n to set

•

n=0—No UDP packet delay (default)

•

n=1–255—Delay in 100ms units, from 100 ms to 25.5 sec.

Rev 4 Jun.16

405

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Standard (Hayes) commands

The following table contains Hayes commands supported on AirLink gateways.

Table D-10: Standard (Hayes) AT Commands

Command Description

+++

AT escape sequence (not preceded by AT)

If a serial terminal is in a data mode, typing this sequence on that serial terminal causes the terminal to re-enter AT command mode. There must be an idle time on the serial port before and after the sequence. The idle time is set by the value in S50.

After you type the AT escape sequence, the terminal remains in AT command mode for

15 seconds before it automatically leaves AT command mode and returns to the previous data mode.

Note: The “+” is ASCII character 0x2B.

Note: The detection of this sequence is disabled if DAE=1.

Query or set Data Carrier Detect (DCD) mode.

DCD is a hardware signal that notifies the software that the device is communicating with another device.

AT&C? to query

AT&Cn to set

•

n=0 — Always assert DCD

•

n=1 — Assert DCD enable when network is ready (default)

Note: Do not use an equal sign (=) when issuing the command.

406 4118967

AT Commands

Table D-10: Standard (Hayes) AT Commands (Continued)

Command Description

D[method] [d.d.d.d]

[/ppppp] or

D[method] [[@]name]

[/ppppp]

Dial a connection to a remote IP and Port using either UDP, TCP, or Telnet.

You can only use ATD#19788 and ATDT#19788 locally.

method

P — Establish a UDP connection

T — Establish a TCP connection

N — Establish a Telnet connection

d.d.d.d

= IP address to establish connection to

name

= Domain name to establish connection to

ppppp

= IP port to establish connection to

Examples:

ATD — Dial (establish) default connection per S53

ATDPnnn.nnn.nnn.nnn[/ppppp] — Dial (establish) UDP session to the specified IP address/ port.

If the method, IP address, or port is omitted, the values from S53 are used. If a Telnet connection is requested (N) and the port is not supplied, port 23 will be used instead of the value from S53.

Several special dialing numbers exist to make it easy to establish a PPP connection with the device. ATD#19788 or ATDT#19788 will establish a PPP connection (see

\APPP on page 400).

If a domain name is specified, the ‘@’ symbol can be used to explicitly indicate the start of the name. For example, if “ATDPHONY” is issued, this will be interpreted as dial a UDP connection to “HONY”. To dial using the default method to host “PHONY”, one would issue

“ATD@PHONY”.

To end the connection, issue the +++ escape sequence or drop the DTR line (if Ignore DTR

S211=0 or &D2).

Note: The source port of the session is the Device Port (set by *DPORT).

*DATZ

Query or set Data Terminal Ready (DTR) mode.

AT&D? to query

AT&Dn to set

•

n=0 — Devices ignores DTR, same effect as HW DTR always asserted (same as

S211=1); DTD is assumed to be on.

•

n=1 — DRT drop causes the device to switch to AT command mode, but does not drop the connection.

•

n=2 — DTR drop causes the connection to drop.

•

n=3—DTR drop causes the connection to reinitialize.

Note: Do not use an equal sign (=) when issuing the command.

Query or set the option to block device reset using ATZ.

AT*DATZ? to query

AT*DATZ=n to set

•

n=0 — Off. Block is disabled—ATZ resets the device. (default)

•

n=1 — On. Block is enabled—ATZ does not reset the device.

Rev 4 Jun.16

407

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Table D-10: Standard (Hayes) AT Commands (Continued)

Command Description

Toggle AT command echo mode.

ATE? to query

ATEn to set

•

n=0 — Echo Off; does not echo commands to the computer

•

n=1 — Echo On; echoes commands to the computer (so you can see what you type)

Note: Do not use an equal sign (=) when issuing the command.

HOR

ATH hangs up, immediately terminates the session (PAD or PPP).

Half-Open Response — In UDP auto answer (half-open) mode.

AT*HOR? to query

AT*HOR=n to set

•

n=0 — No response codes when UDP session is initiated

•

n=1 — RING CONNECT response codes sent out serial link before the data from the first UDP packet

Note: Quiet Mode must be Off.

Query or set AT quiet-mode. If quiet mode is set, there is no responses to AT commands except for data queried.

ATQ? to query

ATQn to set

•

n=0 — Off (default)

•

n=1 — Quiet-mode on

Note: Do not use an equal sign (=) when issuing the command.

Query or set the serial port flow control.

AT\Q? to query

AT\Qn to set

•

n=0 — No flow control

•

n=1 — Hardware flow control

•

n=4 — Transparent software flow control

Note: Do not use an equal sign (=) when issuing the command.

Query or set DSR.

AT&S? to query

AT&Sn to set

•

n=0—Always assert

•

n=1—Assert DSR while in data mode (UDP, TCP, PPP)

Note: Do not use an equal sign (=) when issuing the command.

408 4118967

AT Commands

Table D-10: Standard (Hayes) AT Commands (Continued)

Command Description

Query or set TCP auto answer (the number of rings required before the device automatically answers a call).

ATS0? to query

ATS0n to set

•

n=0— Disable

•

n=1—Enable

Note: Do not use an equal sign (=) when issuing the command.

S23

Query or set the Serial port configuration

ATS23? to query

ATS23=[Baud,][Data bits, Parity, Stop Bits] to set

Baud:

•

300

•

1200

•

2400

•

4800

•

9600

•

19200

•

38400

•

57600

•

115200

Data bits:

•

Parity:

•

O=Odd

•

E=Even

•

N=None

•

M=Mark

Stop Bits:

•

1.5

•

Example:

ATS23=115200,8,N,2 (Sets the device to 115200, etc.)

The settings take effect after reboot.

Note: Must be 8 data bits for PPP mode.

Rev 4 Jun.16

409

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Table D-10: Standard (Hayes) AT Commands (Continued)

Command Description

S211

S221

For applications or situations where hardware control of the DTR signal is not possible, the device can be configured to ignore DTR. When Ignore DTR is enabled, the device operates as if the DTR signal is always asserted.

ATS211? to query

ATS211=n to set

•

n=0—Use hardware DTR (default)

•

n=1—Ignore DTR

•

n=3—Ignore DTR and assert DSR.

Query or set the Connect Delay—the number of seconds to delay the connect response when establishing a TCP connection.

ATS211? to query

ATS211=n to set

•

n=0–255

Query or set the AT command responses (verbosity).

ATV? to query

ATVn to set

•

n=0 — Numeric (terse) command responses (The numeric responses follow the Hayes

Standards for commands.)

•

n=1 — Text string (verbose) command responses (default)

Note: Do not use an equal sign (=) when issuing the command.

Lists most AT commands and their current values. If the parameter is not configured, the AT command returns “Not Set”.

Saves the settings for parameters that are temporarily set without being permanently written to the memory.

This command does not apply to ALEOS because once you issue an AT command or change a setting in ACEmanager and click Apply, the changes are saved in non-volatile memory and are persist across reboots.

Query or set the Extended Call Process Result mode

ATX? to query

ATXn to set

•

n=0 — No extended code (default)

•

n=1 — Adds the text 19200 to the connect response

Reboots the AirLink gateway.

Note: If *DATZ is set to 1, Z is blocked. See *DATZ on page 407.

410 4118967

AT Commands

I/O

Table D-11: Input / Output AT Commands

Command Description

*DIGITALIN1?

Query individual digital inputs. The digital inputs report either a 0 (open) or 1 (closed).

AT*DIGITALIN1?

•

Digital 1 is the on-board digital input.

*PULSECNT1?

*RELAYOUT1

Volts

-0.5 –1.2

1.3 – 30 1

Digital value

Query the I/O pulse counts for digital in.

AT*PULSECNT1?

Query or set the relay status.

AT*RELAYOUT1? to query

AT*RELAYOUT1=n to set

•

n=0—OFF

•

n=1—Drive Active Low

Applications

Table D-12: Applications > Data Usage Commands

Command Description

*DATACURDAY?

Display data usage for the current day (in KB).

Example:

AT*DATACURDAY?

<value>

*DATACURDAYSIM1?

If this command is used with an AirLink RV50, the query or set applies to the

Active SIM. Use

*DATACURDAYSIM1?

*DATACURDAYSIM2?

to query or set a specific SIM card, based on the slot it is installed in.

Display data usage for the current day (in KB) for the SIM card in Slot 1 (upper slot).

Example:

AT*DATACURDAYSIM1?

<value>

Rev 4 Jun.16

411

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Table D-12: Applications > Data Usage Commands (Continued)

Command Description

*DATACURDAYSIM2?

Display data usage for the current day (in KB) for the SIM card in Slot 2 (lower slot).

Example:

AT*DATACURDAYSIM2?

<value>

*DATAPLANUNITS

Query or set the units for the data usage report.

AT*DATAPLANUNITS? to query

AT*DATAPLANUNITS=<unit> to set

•

<unit>=1—Sets the units to Megabytes (MB)

•

<unit>=2—Sets the units to Kilobytes (KB)

Examples:

AT*DATAPLANUNITS?

<unit>

*DATAPLANUNITSSIM1

AT*DATAPLANUNITS=<units>

If this command is used with an AirLink RV50, the query or set applies to the

Active SIM. Use

*DATAPLANUNITSSIM1

*DATAPLANUNITSSIM2 to query

or set a specific SIM card, based on the slot it is installed in.

Query or set the units for the data usage report for the SIM card in Slot 1 (upper slot).

AT*DATAPLANUNITSSIM1? to query

AT*DATAPLANUNITSSIM1=<unit> to set

•

<unit>=1—Sets the units to Megabytes (MB)

•

<unit>=2—Sets the units to Kilobytes (KB)

Examples:

AT*DATAPLANUNITSSIM1?

<unit>

AT*DATAPLANUNITSSIM1=<units>

412 4118967

AT Commands

Table D-12: Applications > Data Usage Commands (Continued)

Command Description

*DATAPLANUNITSSIM2

Query or set the units for the data usage report for the SIM card in Slot 2 (lower slot)

AT*DATAPLANUNITSSIM2? to query

AT*DATAPLANUNITSSIM2=<unit> to set

•

<unit>=1—Sets the units to Megabytes (MB)

•

<unit>=2—Sets the units to Kilobytes (KB)

Examples:

AT*DATAPLANUNITSSIM2?

<unit>

*DATAPREVDAY?

*DATAPREVDAYSIM1?

AT*DATAPLANUNITSSIM2=<units>

Query the data usage for the previous day (in KB).

Example:

AT*DATAPREVDAY?

<value>

If this command is used with an AirLink RV50, the query or set applies to the

Active SIM. Use *DATAPREVDAYSIM1?

or *DATAPREVDAYSIM2?

to query or

set a specific SIM card, based on the slot it is installed in.

Query the data usage for the previous day (in KB) for the SIM card in Slot 1

(upper slot).

Example:

AT*DATAPREVDAYSIM1?

<value>

*DATAPREVDAYSIM2?

Query the data usage for the previous day (in KB) for the SIM card in Slot 2

(lower slot).

Example:

AT*DATAPREVDAYSIM2?

<value>

Rev 4 Jun.16

413

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Table D-12: Applications > Data Usage Commands (Continued)

Command Description

*DATAUSAGEENABLE

Query or set enabling Data Usage.

AT*DATAUSAGEENABLE? to query

AT*DATAUSAGEENABLE=<status> to set

•

<status>=0—Data Usage disabled

•

<status>=1—Data Usage enabled

Example:

AT*DATAUSAGEENABLE?

*DATAUSAGEENABLESIM1

*DATAUSAGEENABLESIM2

AT*DATAUSAGEENABLE=<status>

If this command is used with an AirLink RV50, the query or set applies to the

Active SIM. Use

*DATAUSAGEENABLESIM1 or *DATAUSAGEENABLESIM2

to query or set a specific SIM card, based on the slot it is installed in.

Query or set enabling Data Usage for the SIM card in Slot 1 (upper slot).

AT*DATAUSAGEENABLESIM1? to query

AT*DATAUSAGEENABLESIM1=<status> to set

•

<status>=0—Data Usage disabled

•

<status>=1—Data Usage enabled

Example:

AT*DATAUSAGEENABLESIM1?

AT*DATAUSAGEENABLESIM1=<status>

Query or set enabling Data Usage for the SIM card in Slot 2 (lower slot).

AT*DATAUSAGEENABLESIM2? to query

AT*DATAUSAGEENABLESIM2=<status> to set

•

<status>=0—Data Usage disabled

•

<status>=1—Data Usage enabled

Example:

AT*DATAUSAGEENABLESIM2?

AT*DATAUSAGEENABLESIM2=<status>

414 4118967

AT Commands

Table D-12: Applications > Data Usage Commands (Continued)

Command Description

*GARMINATTACH

*GARMINSTATUS?

Query or set the ability to connect a Garmin device to the serial port (so the

Garmin device can communicate with a remote server). For more information, see

Garmin on page 274.

AT*GARMINATTACH? to query

AT*GARMINATTACH=n to set

•

n=0—Disable

•

n=1—Enable

Query Garmin device attachment status.

Table D-13: Applications > ALEOS Application Framework (AAF)

Command Description

*AAFINSTALL

*AAFUNINSTALL

Query installed AAF applications and their status and install new AAF applications

•

AT*AAFINSTALL? returns the installation status of the last installed application, and list of installed AAF applications and the status of each application.

•

AT*AAFINSTALL?<application name> returns the status of the specified AAF application.

•

AT*AAFINSTALL=<hostname>,<user>,<password>,<application filename> downloads and installs the specified AAF application from the FTP server at

<hostname> using <user> <password> credentials.

Install an AAF application

AT*AAFUNINSTALL=<application name> uninstalls the specified AAF application.

Admin

Table 4-14: Admin > Advanced Commands

Command

*BLOCK_RESET_CONFIG

Description

Query or set the ability to block resetting the device to factory default settings using the hardware Reset button.

AT*BLOCK_RESET_CONFIG? to query

AT*BLOCK_RESET_CONFIG=n to set

•

n=0—Reset button can be used to reset the device to factory default settings.

(default).

•

n=1—Device cannot be reset to factory default settings using the Reset button on the device.

Note: This command only blocks the ability to reset to defaults using the Reset button on the device. You can still reset the device to the factory default settings

using the “Reset to Factory Default” button in ACEmanager or the *RESETCFG

AT command.

*BOARDTEMP?

Query the temperature of the internal hardware, in degrees Celsius.

Rev 4 Jun.16

415

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Table 4-14: Admin > Advanced Commands (Continued)

Command Description

*MSCIUPADDR

*MSCIUPDPERIOD

NSLOOKUP

Query or set the IP address or FQDN and port that periodic device status updates are sent to.

AT*MSCIUPADDR[IP address or FQDN][/port]? to query

AT*MSCIUPADDR=[IP address or FQDN][/port] to set

Examples: 192.168.14.100/3333

MyDevice.com/3333

Query or set the device status update interval (in seconds). Thsi specifies how frequently the device status update is sent to the port configured in

*MSCIUPADDR .

AT*MSCIUPDPERIOD? to query

AT*MSCIUPDPERIOD=n to set

•

n=0 — Disabled

•

n=1–255 seconds

Immediately performs an NSLookup on the supplied FQDN.

ATNSLOOKUP=[FQDN]

*POWERIN?

*RESETCFG

Query the voltage input to the internal hardware.

AT*RESTCFG resets the device to factory default settings.

Important:

There is no confirmation requested. The AT command takes effect immediately.

*REMOTELOG

*SECUREMODE

Exports the log file to a remote destination (Syslog Server). Specifying the port is option. If the port is not specified, the default port, 514, is used.

You can only use this command locally.

AT*REMOTELOG=SYSLOG SERVER IP,PORT

Query or set the secure mode that blocks most ports (and ICMP) for over-the-air

(OTA) or OTA and local to prevent unwanted access to the device.

AT*SECUREMODE? to query

AT*SECUREMODE=n to set

•

n=0 Off; normal behavior

•

n=1 Disables:

•

Web management ports (ACEmanager and ALMS access) from the OTA interface

•

Internet Control Message Protocol (ICMP), used for PING, for OTAn=2

Disables:

•

Web management ports from the Over-the-air (OTA) interface

•

Internet Control Message Protocol (ICMP) for OTA and Wi-Fi

•

ICMP for local ports (Ethernet, USB, and Serial)

Note: Telnet and SSH ALEOS ports remain open regardless of the secure mode setting. This enables you to connect an AT console to manage the device. DHCP and DNS ports also remain open to allow the device to provide IP addresses to hosts and relay the DNS service.

416 4118967

AT Commands

Table 4-14: Admin > Advanced Commands (Continued)

Command Description

*SYSRESETS?

*USBBYPASS

Query the number of resets since the device was reset to factory default settings.

Query or set Radio Passthru mode.

AT*USBBYPASS? to query

AT*USBBYPASS=n to set

•

n=0—Disable

•

n=1—Enable

Rev 4 Jun.16

417

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

418 4118967

Rev 4 Jun.16

E: SMS Commands

SMS Command format

PW [Password] [Prefix][Command or Command parameter1]

[Command parameter2 (if applicable)] [Command parameter n]

Note: There is no space between the prefix and the command (or the 1st command parameter in the case of multi-parameter commands). There must be a single space between all other fields to act as a delimiter.

SMS mode

Password Only

Control Only

Gateway Only

Control and Gateway

The default password is the last 4 digits of the SIM ID number (for

SIM-based devices) and the last 4 digits of the ESN (for non-SIM devices). If you do not know the SIM ID or ESN number, you can find it in ACEmanager on the Status > WAN/Cellular page.

The default prefix is “&&&”.

Whether or not a password and prefix are required varies depending on the SMS mode selected in ACEmanager.

Password

(configurable in all modes)

Always required

Required when sending from a non-trusted phone number

Always required

Required when sending from a non-trusted phone number

Prefix

Required

Use default (not configurable)

Prefix is configurable.

The prefix can be omitted if the ALEOS

Command Prefix field in ACEmanager

(Services > SMS) is configured to be blank.

Required

Use default (not configurable)

Required

Configurable, but cannot be blank

When an SMS command is received, the AirLink gateway performs the action requested and sends a response back to the phone number from which it received the SMS.

For more examples and detailed instructions, see

SMS Overview on page 167.

419

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Command

List of SMS Commands

Action Result

Note: Some responses start with “reply from [device name]:” However, this feature is currently unavailable for the

Enable, and Provision commands.

[prefix]enable <value>

[prefix]status

[prefix]reset

[prefix]relay x y

[prefix] GPS

Enable/disable the device(s) being managed by ALMS.

“AVMS enable set to status:” <value>

<value>=0 Disable

<value>=1 Enable

None status IP

[Network IP] [Network Status]:

[technology type] RSS signalled

Lat = [Latitude]

Long = [Longitude]

Time = [hh:mm:ss]

Resets the device 30 seconds after the first response message is sent.

Sets the applicable relay to the desired setting.

First message: Reset in 30 seconds

Second message: Status message when back up.

relay x set to y x can be 1 y can be 0 or 1 (Off or Drive active low)

The device replies with its current GPS location.

The device sends a link to a map showing its location. You can copy the link into a browser to view the location, or if the SMS is sent from a smartphone, you can click the link to view the map.

420 4118967

SMS Commands

Command Action Result

[prefix]Provision <APN> <Network

User ID> <Network Password>

<Network Authentication Mode>

Note: You can omit any of the above parameters.

•

To omit a parameter before the one you want to change, use a period (.) in place of the omitted parameter.

Example: &&&provision . [email protected] . chap changes only the user ID and authentication mode.

•

If you want to omit any parameters after the one you want to change, simply omit them.

Example: &&&provision access.apn changes only the apn.

After the unit is installed and the SIM card inserted, you can use this command to provision the account.

Network Authentication

Mode is optional. If used, enter one of the following:

•

None

•

PAP

•

CHAP

These are not case sensitive.

If an unknown mode is entered or the field is omitted, None is used.

“provision”

“apn:” <APN>

“user ID” <Network User ID>

“PW” <Network Password>

“auth mode” <Network Authentication Mode>

Note: If a parameter is omitted, the response displays “Not Set” for that parameter.

Note: Use of this command is valid for

LTE, HSPA, and GPRS networks, but not valid for CDMA only networks.

[prefix]AVMS <server> <interval>

Note: All of the above must be on a single line. The interval must be greater than 0.

Omitting any field results in a response of

“not set” and the configuration parameter does not change.

Modifies the ALMS server’s

URL and ALMS communication period

(interval in minutes)

“AVMS”

“srv:” <Server>

“interval:” <Interval>

[prefix]AVMSCHECKIN

Prompts the device to communicate with the ALMS server. Once AirLink

Management Service receives the heartbeat message, it can respond and send an MSCI command to the device (i.e Write/Read/

Firmware Update).

“AVMS connection requested”

Rev 4 Jun.16

421

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

422 4118967

F: Q & A and Troubleshooting

ACEmanager Web UI

The ACEmanager page is not displaying properly.

Ensure the you are using a supported browser. See page 15

for a list of supported browsers.

Hold the Shift key + click the Refresh button. This reloads the page, while ignoring what is in the cache.

If the problem persists:

•

Clear the cache. (The procedure varies, depending on the browser.)

•

Restart the browser.

•

Restart your computer.

Templates

The template does not upload properly when I use Internet

Explorer 9.

To resolve the problem:

In Internet Explorer 9, go to Tools > Internet Options.

Select the Security tab.

Rev 4 Jun.16

Figure F-1: Internet Explorer 9: Tools > Internet Options > Security tab

423

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Click Custom level....

Scroll down until you see “Include local directory path when uploading files to a server”.

Select Disable.

424

Figure F-2: Internet Explorer 9: Security Settings

Click OK.

Updating the ALEOS Software and Radio

Module Firmware

I am unable to update the ALEOS software and radio module firmware using ACEmanager.

If you are having trouble updating the ALEOS software or radio module firmware, especially if you are updating from an older version of ALEOS:

Try using a different browser. (ACEmanager supports the latest versions of

Internet Explorer and Firefox.)

Delete the browser cookies/cache before logging into ACEmanager. (The

Web browser short-cut is Control + Shift + Delete.)

Backup your device settings by downloading and saving the template. See

Saving a Custom Configuration as a Template on page 17.

Reset the device to factory default settings. (See

Reset to Factory Default on page 293 or press and hold the reset button on the device for 7 to 10

seconds.)

If you are updating from ALEOS 4.3.3 or earlier, be sure to follow the correct software update path. For more information, refer to the Upgrading to ALEOS

4.3.4 from Older Versions Application Note (part number 4115254) available on source.sierrawireless.com.

4118967

Q & A and Troubleshooting

Begin the update process (see

Update the ALEOS Software and Radio

Module Firmware on page 22) and follow the prompts.

If after 30 minutes the Web UI is frozen, log in using a different browser and confirm whether or not the ALEOS software and radio module firmware has been updated correctly.

If you are still having problems, contact your Sierra Wireless distributor.

When I try to update ALEOS using ACEmanager, I see the following message: “... Check that your package is compatible with the device”.

Rev 4 Jun.16

This message also appears if you are only updating the radio module firmware and you have the Update ALEOS radio button selected.

To correct the problem:

Close the Update page.

Retry the radio firmware update, being careful to select the Radio Module

Firmware that is appropriate for your gateway.

When I try to update ALEOS using ACEmanager, I see the following message: “Please select a firmware for xxxx”.

This message appears and you are blocked from continuing with the update if you are only updating the radio module and you select a radio module firmware file designed for a different radio module.

To correct the problem:

Click OK.

425

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

426

Select a radio module firmware file for the radio module in the AirLink gateway you are updating and click update. (To check which radio module is in your device, in ACEmanager, go to Status > About.)

Poor Wireless Network Connection

ACE manager indicates that my AirLink gateway has a poor wireless connection. What can I do to improve it?

For GSM or CDMA networks:

Check the RSSI value. If ACEmanager (Status screen) indicates a good RSSI

value, go to step 2

. If it indicates a poor RSSI value:

· Check the antenna connection.

· Make sure you have the correct antenna for the device.

· You may be in an area with poor coverage. Check with your Mobile Network

Operator, or if possible, try moving the AirLink gateway to a new location.

Check the Ec/Io value. If ACEmanager (Status screen) indicates a poor Ec/Io value:

· This may be a temporary network problem caused by local interference.

· A nearby laptop or other electronic equipment may be interfering with the signal. Try moving the AirLink gateway to a different location.

For LTE networks:

Check the RSSI value. If ACEmanager (Status screen) indicates a good RSSI

value, go to step 2

. If it indicates a poor RSSI value:

· Check the antenna connection.

· Make sure you have the correct antenna for the device.

· Try moving the AirLink gateway to a different location.

Check the RSRP value. If ACEmanager (Status screen) indicates a good

RSRP value, go to step

. If it indicates a poor RSRP value:

· This may be a temporary network problem caused by local interference.

· Check the antenna connection.

· Make sure you have the correct antenna for the device.

· You may be in an area with poor coverage. Check with your Mobile Network

Operator, or if possible, try moving the AirLink gateway to a new location.

Check the RSRQ value. If ACEmanager (Status screen) indicates a poor

RSRQ value:

· A nearby laptop or other electronic equipment may be interfering with the signal. Try moving the AirLink gateway to a different location.

Connection not working

My gateway appears to be connected to the host, but no data is being transferred.

Check to see if MAC filtering is enabled (Security > MAC Filtering).

If MAC filtering is enabled:

•

Ensure that the MAC Address for the host in question is on the Allowed List.

4118967

Rev 4 Jun.16

Q & A and Troubleshooting

•

Ensure that there are no typos in the MAC Address.

•

If it is not required, disable MAC Filtering and reboot the device.

My host device is unable to connect to the Internet, even when there is good mobile network coverage and ALEOS can Ping an external IP address.

Check the DNS proxy setting described on

page 106

You may need to change this setting to Disable so that all connected devices acquire the Mobile Network Operator-defined DNS server as the first DNS server. The AirLink gateway is not used as the DNS resolver.

LTE Networks

How do I interpret the number shown in the Band Class field on the

Status > WAN Cellular page for a device on an LTE network?

Use the following table to interpret the values in the LTE Band Class field in

ACEmanager (STATUS > WAN Cellular).

130

131

132

133

126

127

128

129

Band Class number

Uplink frequency range

(MHz)

120

121

1920–1980

1850–1910

Downlink frequency range

(MHz)

2110–2170

1930–1990

122

123

124

125

1710–1785

1710–1755

824–849

830–840

1805–1880

2110–2155

869–894

875–885

134–135

136

137

2500–2570

880–915

1749.9–1784.9

1710–1770

1427.9–1452.9

698–716

777–787

788–798

Reserved for bands 15 and 16

704–716

815–830

2620–2690

925– 960

1844.9–1879.9

2110–2170

1475.9–1500.9

728–746

746–756

758–768

734–746

860–875

427

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Band Class number

Uplink frequency range

(MHz)

138

139

140

141–151

152

153

154

155

156

157

158

159

830–845

832–862

1447.9–1462.9

Reserved for bands 22 to 32

1900–1920

2010–2025

1850–1910

1930–1990

1910–1930

2570–2620

1880–1920

2300–2400

Downlink frequency range

875–890

791–821

(MHz)

1495.9–1510.9

1900–1920

2010–2025

1850–1910

1930–1990

1910–1930

2570–2620

1880–1920

2300–2400

How do I obtain and interpret SINR values for LTE networks?

You can use the AT*CELLINFO? command to obtain an SINR (Signal to

Interference plus Noise Ratio) value. (See *CELLINFO2?

on page 357.)

The values vary depending on the network characteristics and the AirLink gateway, but in general, a positive value provides usable throughput. The following table provides guidelines for interpreting SINR values.

Throughput SINR Value

0 to 5

6 to 10

> 10

Poor

Fair

Good

Excellent

If the SINR value indicates poor throughput:

•

Move the antenna away from noisy equipment.

•

Move closer to the nearest cell tower line of sight, or further away from the interfering cell tower.

SIM Card is Blocked

My SIM card has a PIN number. I’ve entered the wrong PIN several times and now the SIM card is blocked.

428 4118967

Rev 4 Jun.16

Q & A and Troubleshooting

AirLink products do not support Personal Unlocking Key (PUK) entry. However, if you need to unblock the SIM card:

Contact your Mobile Network Operator to obtain the PUK.

Remove the SIM card from the AirLink gateway and insert it in a cell phone that accommodates a MiniSIM (2FF) card.

Enter the PUK to unblock the SIM card and then return the SIM card to the

AirLink gateway.

Note: Be careful when entering the PUK. You have a limited number of attempts to enter the correct PUK (generally 10) before the SIM card is permanently disabled and a new SIM card is required. If the PUK does not unblock the SIM card after the first few attempts, contact your Mobile Network Operator.

Remote connections

I cannot connect to the AirLink gateway remotely over the Mobile

Network Operator’s Private Network via the Web UI, although I can connect to it locally.

Some Mobile Network Operators' private networks have restrictions on the maximum transmission unit (MTU) size. This is more prevalent with LTE networks.

Possible solutions:

•

Use your Mobile Network Operator’s public network.

•

Ask your Mobile Network Operator to reduce the MTU size on the router or other equipment at their end of the private network. Setting the MTU value below 1500 bytes (for example 1326 bytes) has resolved the problem on some private networks.

Radio Band Selection

I set the radio band in the UI (WAN/Cellular > Setting the Band) or by using the AT!BAND AT command, but after I reboot the band setting reverts to its former value.

For some SIM cards, you need to set the band before inserting the SIM card.

To resolve this problem:

Remove the SIM card.

Set the band to the desired value.

Reboot the device.

Insert the SIM card.

429

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Low Voltage Standby Mode

How do I get my gateway out of Low Voltage Standby mode?

The problem: While configuring Low Voltage Standby mode, I inadvertently set the Resume Immediately Voltage too high (i.e. higher than the voltage available where the gateway is installed). Now the gateway is stuck in standby mode.

I connected the gateway to a higher voltage source, and it resumed normal operation. I reset the Low Voltage Standby values, but the gateway returned to

Standby mode as soon as it was reconnected to the lower voltage source, even though the lower voltage source provided a higher voltage than the new value I just set in the Resume immediately at Voltage field.

The solution: Low Voltage Standby mode settings take effect as soon as you click Apply, but they are not permanently stored until the gateway is rebooted. To bring a gateway out of Low Voltage Standby mode if the Resume immediately at

Voltage field is set too high:

Connect the gateway to a power source and supply voltage that is greater than the value configured in the Resume immediately at Voltage field.

When the gateway resumes normal operation, launch ACEmanager and reset the values in the Services > Power Management > Low Voltage Standby fields.

While still using the voltage applied in step

, Click the Reboot button in

ACEmanager to reboot the gateway.

The gateway reboots.

Wait until the gateway reboots itself a second time, or for at least 3 minutes, if you are not sure if the gateway has done its automatic reboot.

Once the second reboot is complete, it is safe to disconnect the gateway from the higher power source and return it to the original installation and power source.

Reliable Static Routing (RSR)

I launched ACEmanager with Internet Explorer 9. I configured RSR, but after I enabled RSR and clicked Apply, all the values reverted to the defaults.

There is a known issue. If you configure and enable RSR with ACEmanager in

Internet Explorer 9, and then click Apply, the values in the ACEmanager screen appear as default values.

This is an ACEmanager display issue only. The configuration is applied properly, but the configured values are not displayed. Click Refresh to view the configured values.

430 4118967

Rev 4 Jun.16

Q & A and Troubleshooting

Inbound Ports Used by ALEOS

When I configure ports for an application on a LAN client such as a router or laptop, I want to ensure that the ports I use do not conflict with the inbound ports that ALEOS uses. Which ports does ALEOS use?

Table F-1

shows the inbound ports that are set in ALEOS and cannot be

configured. Table F-2

show the default setting for ports you can configure and where to change the ports in ACEmanager.

Table F-1: ALEOS Non-configurable Inbound Ports

Port Use

Used internally for GPS and Events Reports 9494 – 9497

17335

17345 – 17353

21000 – 21003

500

4500

8088

Used internally for IPSec VPN

Used internally for ALMS

Table F-2: ALEOS Configurable Inbound Ports

Default

Port

Feature ACEmanager location

161

2332

9191

9300

9443

9494

12345

SNMP Port

SSH/Telnet Remote Login Server Port

ACEmanager Port

SSL tunnel Port

ACEmanager SSL Port

GPS Poll Port

Device Port used for incoming TCP/

UDP traffic

Services > Management (SNMP)

Services > Telnet/SSH

Services > ACEmanager

VPN > SSL Tunnel

Services > ACEmanager

GPS > Global Settings

Serial > Port Configuration

431

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Setting for Band

The options available in the WAN/Cellular > WAN/Cellular Setting for Band field depend on your region or your Mobile Network Operator. (To check your Mobile

Network Operator, in ACEmanager, go to Status > About > Radio Module

Identifier field.) Check the appropriate table for a list of options that apply to your device:

United States of America:

AT&T

Verizon Wireless

International

Table F-3 on page 432

Table F-4 on page 433

Sprint

Table F-5 on page 434

Generic North America

All North American Mobile Network

Operators not listed above

Table F-6 on page 435

Table F-7 on page 437

AT&T

Table F-3: Setting for Band — AT&T

Setting for Band Option Technology

All Bands 2G

Europe 3G

North America 3G

Europe 2G

North America 2G

3G UMTS

(DC Included)

4G LTE - FDD

3G UMTS

(DC Included)

3G UMTS

(DC Included)

Bands available

GSM 850

GSM EGSM 900

GSM PGSM 900

GSM DCS 1800

GSM PCS 1900

B1 (2000 MHz)

B2 (1900 MHz)

B5 (850 MHz)

B6 (800 MHz)

B8 (900 MHz)

B2 (1900 MHz)

B4 (AWS 1700 MHz)

B5 (850 MHz)

B17 (700 MHz)

B1 (2100 MHz)

B8 (900 MHz)

B2 (1900 MHz)

B5 (850 MHz)

B6 (800 MHz)

GSM EGSM 900

GSM PGSM 900

GSM DCS 1800

GSM 850

GSM PCS 1900

432 4118967

Q & A and Troubleshooting

Table F-3: Setting for Band — AT&T

Setting for Band Option Technology

GSM ALL 2G

Europe

North America

WCDMA ALL

LTE ALL

3G UMTS

(DC Included)

3G UMTS

(DC Included)

4G LTE - FDD

3G UMTS

(DC Included)

4G LTE - FDD

Bands available

GSM 850

GSM EGSM 900

GSM PGSM 900

GSM DCS 1800

GSM PCS 1900

GSM EGSM 900

GSM PGSM 900

GSM DCS 1800

B1 (2000 MHz)

B8 (900 MHz)

GSM 850

GSM PCS 1900

B2 (1900 MHz)

B5 (850 MHz)

B6 (800 MHz)

B2 (1900 MHz)

B4 (AWS 1700 MHz)

B5 (850 MHz)

B17 (700 MHz)

B1 (2000 MHz)

B2 (1900 MHz)

B5 (850 MHz)

B6 (800 MHz)

B8 (900 MHz)

B2 (1900 MHz)

B4 (AWS 1700 MHz)

B5 (850 MHz)

B17 (700 MHz)

Verizon Wireless

Table F-4: Setting for Band — Verizon Wireless

Setting for Band Option Technology

All Bands CDMA

3G UMTS

(DC Included)

4G LTE - FDD

Bands available

BC0 (800 MHz)

BC1 (1900 MHz)

GSM 850

GSM EGSM 900

GSM DCS 1800

GSM PCS 1900

B1 (2000 MHz)

B2 (1900 MHz)

B5 (850 MHz)

B8 (900 MHz)

B4 (AWS 1700 MHz)

B13 (700 MHz)

Rev 4 Jun.16

433

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Table F-4: Setting for Band — Verizon Wireless

Setting for Band Option Technology

North America CDMA

4G LTE - FDD

North America 3G

North America 4G

World Mode

CDMA

4G LTE - FDD

CDMA

3G UMTS

(DC Included)

4G LTE - FDD

Bands available

BC0 (800 MHz)

BC1 (1900 MHz)

B4 (AWS 1700 MHz)

B13 (700 MHz)

BC0 (800 MHz)

BC1 (1900 MHz)

B4 (AWS 1700 MHz)

B13 (700 MHz)

BC0 (800 MHz)

BC1 (1900 MHz)

GSM 850

GSM EGSM 900

GSM DCS 1800

GSM PCS 1900

B1 (2000 MHz)

B2 (1900 MHz)

B5 (850 MHz)

B8 (900 MHz)

B4 (AWS 1700 MHz)

B13 (700 MHz)

Sprint

Table F-5: Setting for Band — Sprint

Setting for Band Option Technology

Automatic CDMA

LTE Only

CDMA Only

3G UMTS

(DC Included)

4G LTE - FDD

CDMA

Bands available

BC0 (800 MHz)

BC1 (1900 MHz)

BC10 (1900 MHz)

GSM 850

GSM EGSM 900

GSM PGSM 900

GSM DCS 1800

GSM PCS 1900

B1 (2000 MHz)

B2 (1900 MHz)

B5 (850 MHz)

B8 (900 MHz)

B25 (1900 MHz G Block)

BC0 (800 MHz)

BC1 (1900 MHz)

BC10 (1900 MHz)

434 4118967

Q & A and Troubleshooting

Table F-5: Setting for Band — Sprint

Setting for Band Option Technology

GSM Only 2G

3G UMTS

(DC Included)

Bands available

GSM 850

GSM EGSM 900

GSM PGSM 900

GSM DCS 1800

GSM PCS 1900

B1 (2000 MHz)

B2 (1900 MHz)

B5 (850 MHz)

B8 (900 MHz)

Generic North America

Table F-6: Setting for Band — Generic North America

Setting for Band Option Technology

All Bands CDMA

Bands available

BC0 (800 MHz)

BC1 (1900 MHz)

BC10 (1900 MHz)

Europe 3G

North America 3G

Europe 2G

North America 2G

GSM ALL

3G UMTS

(DC Included)

4G LTE - FDD

3G UMTS

(DC Included)

3G UMTS

(DC Included)

GSM 850

GSM EGSM 900

GSM PGSM 900

GSM DCS 1800

GSM PCS 1900

B1 (2000 MHz)

B2 (1900 MHz)

B4 (AWS 1700 MHz)

B5 (850 MHz)

B8 (900 MHz)

B2 (1900 MHz)

B4 (AWS 1700 MHz)

B5 (850 MHz)

B13 (700 MHz)

B17 (700 MHz)

B25 (1900 MHz G Block)

B1 (2100 MHz)

B8 (900 MHz)

B2 (1900 MHz)

B5 (850 MHz)

GSM EGSM 900

GSM PGSM 900

GSM DCS 1800

GSM 850

GSM PCS 1900

GSM 850

GSM EGSM 900

GSM PGSM 900

GSM DCS 1800

GSM PCS 1900

Rev 4 Jun.16

435

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Table F-6: Setting for Band — Generic North America

Setting for Band Option Technology

Europe

North America

3G UMTS

(DC Included)

CDMA

Bands available

GSM EGSM 900

GSM PGSM 900

GSM DCS 1800

B1 (2000 MHz)

B8 (900 MHz)

BC0 (800 MHz)

BC1 (1900 MHz)

GSM 850

GSM PCS 1900

3G UMTS

(DC Included)

4G LTE - FDD

WCDMA ALL

LTE ALL

CDMA ALL

3G UMTS

(DC Included)

4G LTE - FDD

CDMA

B2 (1900 MHz)

B5 (850 MHz)

B2 (1900 MHz)

B4 (AWS 1700 MHz)

B5 (850 MHz)

B13 (700 MHz)

B17 (700 MHz)

B1 (2000 MHz)

B2 (1900 MHz)

B4 (AWS 1700 MHz)

B5 (850 MHz)

B8 (900 MHz)

B2 (1900 MHz)

B4 (AWS 1700 MHz)

B5 (850 MHz)

B13 (700 MHz)

B17 (700 MHz)

B25 (1900 MHz G Block)

BC0 (800 MHz)

BC1 (1900 MHz)

BC10 (1900 MHz)

436 4118967

Q & A and Troubleshooting

International

Table F-7: Setting for Band — International

Setting for Band Option Technology

All Bands 2G

Europe 3G

North America 3G

Europe 2G

North America 2G

GSM ALL

Europe

North America

3G UMTS

(DC Included)

4G LTE - FDD

3G UMTS

(DC Included)

3G UMTS

(DC Included)

3G UMTS

(DC Included)

4G LTE - FDD

3G UMTS

(DC Included)

GSM EGSM 900

GSM PGSM 900

GSM DCS 1800

GSM 850

GSM PCS 1900

GSM 850

GSM EGSM 900

GSM PGSM 900

GSM DCS 1800

GSM PCS 1900

GSM EGSM 900

GSM PGSM 900

B1 (2000 MHz)

B8 (900 MHz)

B1 (2100 MHz)

B3 (1800 MHz)

B7 (2600 MHz)

B8 (900 MHz)

B20 (800 MHz)

GSM 850

GSM PCS 1900

B2 (1900 MHz)

B5 (850 MHz)

Bands available

GSM 850

GSM EGSM 900

GSM PGSM 900

GSM DCS 1800

GSM PCS 1900

B1 (2000 MHz)

B2 (1900 MHz)

B5 (850 MHz)

B8 (900 MHz)

B1 (2100 MHz)

B3 (1800 MHz)

B7 (2600 MHz)

B8 (900 MHz)

B20 (800 MHz)

B1 (2100 MHz)

B8 (900 MHz)

B2 (1900 MHz)

B5 (850 MHz)

Rev 4 Jun.16

437

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Table F-7: Setting for Band — International

Setting for Band Option Technology

WCDMA ALL 3G UMTS

(DC Included)

LTE ALL 4G LTE - FDD

B1 (2000 MHz)

B2 (1900 MHz)

B5 (850 MHz)

B8 (900 MHz)

B1 (2100 MHz)

B3 (1800 MHz)

B7 (2600 MHz)

B8 (900 MHz)

B20 (800 MHz)

Bands available

Ethernet Ports

What do the LEDs above the Ethernet port mean?

There are two LEDs at the top of the Ethernet port. The green on is lit when there is a cable connected to the host and the connection is running at 100baseT. The amber (activity) LED blinks when traffic is passing through the port.

LAN Networks

The server on my LAN network is receiving data from some hosts on the network, but not others. What’s wrong?

To correct this problem:

Launch ACEmanager.

Go to the LAN tab.

Select Ethernet.

Refer to the instructions for setting the Starting Ephemeral Port on page 99.)

VPN

My VPN connection is not working. When I try to debug it using the logs on the Admin page, VPN information does not show up in the log.

VPN information is collected in the Linux logs. To view this information:

Log into ACEmanager as User and go to Admin > Log.

438 4118967

Q & A and Troubleshooting

Rev 4 Jun.16

In the drop-down menu beside Linux Syslog, ensure that Display is selected.

If you change the setting:

Click Apply.

b. Reboot the device.

Click View Log.

On the View Log page, click Clear and then click Refresh.

VPN Troubleshooting

If you see the following lines in the log, it means the VPN Server is not answering.

notice openvpn[9199]: [UNDEF] Inactivity timeout (--ping-restart), restarting notice openvpn[9199]: TCP/UDP: Closing socket

Check the VPN Server status.

When I configure a VPN, my Internet connection stops working.

When you configure a VPN, outgoing traffic from the host to the public Internet is blocked by default, as a security measure. If you want to enable public Internet traffic from the host:

In ACEmanager, go to VPN > Split Tunnel.

Change the Outgoing Host Out of Band field to Allowed.

Click Apply.

439

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Port Forwarding

I set up port forwarding rules. I did not receive an error message, but it seems that data is not being forwarded.

If the Public Start Port and Public End Port fields are not set up correctly, data is not forwarded.

In ACEmanager, go to Security > Port Forwarding.

•

If you are forwarding data to a single port:

· Ensure that the value in the Public Start Port field is not 0.

· Ensure that the value in the Public End Port field is 0.

· Ensure that the value in the Private Port start field is not 0.

•

If you are forwarding data to a range of ports:

Ensure that the value in the Public Start Port field is not 0.

· Ensure that the value in the Public End Port field is greater than the value in

Public Start Port field.

· Ensure that the value in the Private Port Start field is not 0.

For complete instructions, see Port Forwarding on page 137.

SMS

I tried to send an SMS message, and received an error code. What does the error code mean?

201

202

203

204

The following acknowledgment error codes may appear if your message was not successfully sent:

Code: Explanation:

100 Not in coverage (no cellular service)

Parse Error on field #1 (Start Field)

Parse Error on field #2 (Phone number and separator)

Parse Error on field #3 (Data type and separator)

Parse Error on field #4 (Payload length and separator)

205

301

Parse Error on field #5 (Message and End Field)

No buffers available

302 SMS queue full

Supported SMS data types are ASCII, 8-bit, and Unicode, and are all casesensitive. SMS messages being sent MUST be in ASCII hex format.

I tried to send an SMS command and received the error “not set”.

The parameter was not changed.

440 4118967

Q & A and Troubleshooting

Check the format of the SMS command. There should be no space between the prefix and the command (or the 1st command parameter in the case of multiparameter commands), and a single space between all other fields to act as a delimiter. For more information, see

SMS Commands on page 419 and

SMS

Overview on page 167.

AirLink Management Service

I don’t understand the message that appears in the Status field in the

Services > ALMS page.

The error messages in the Services > ALMS > Status field can be due to a communication failure, a problem with the ALMS server, or a failure when parsing a valid ALMS server response. The following table describes the error messages and the corrective action.

Error message Meaning Corrective action

Communication Failure Errors

[HTTP] Initialization error

[HTTP] Unsupported protocol

[HTTP] Failed initialization

[HTTP] URL using bad/illegal format or missing URL

The transfer object could not be initialized.

The ALMS server URL protocol is not supported.

Contact ALMS support a

In ACEmanager, check the ALMS URL in the

Service > ALMS > Server URL field. The default value is https://na.m2mop.net/device/msci/com .

Contact ALMS support a

The transfer library could not be initialized.

The ALMS server URL is missing or not properly formatted.

In ACEmanager, check the ALMS URL in the

Service > ALMS > Server URL field. The default value is https://na.m2mop.net/device/msci/com .

[HTTP] Couldn't resolve host name

[HTTP] Couldn't connect to server

The ALMS server URL could not be resolved.

In ACEmanager, check the ALMS URL in the

Service > ALMS > Server URL field. The default value is https://na.m2mop.net/device/msci/com .

Also check the cellular connectivity.

Connection to the ALMS server

URL failed.

In ACEmanager, check the ALMS URL in the

Service > ALMS > Server URL field. The default value is https://na.m2mop.net/device/msci/com .

Also check the cellular connectivity.

[HTTP] Timeout was reached The transfer timeout (equal to the communication period if defined or

5 minutes) expired.

[HTTP] Server returned nothing

(no headers, no data)

No data was received from the

ALMS server.

[HTTP] Unrecognized or bad

HTTP Content or Transfer-

Encoding

[HTTP] Out of memory

The ALMS server HTTP response contains a malformed content or transfer-encoding header field.

A memory allocation problem occurred.

Check cellular connectivity.

Contact ALMS support

Contact ALMS support a a

Rev 4 Jun.16

441

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Error message

[HTTP] SSL peer certificate or

SSH remote key was not OK

Meaning

This message appears if you are using an HTTPS server URL, the

SSL Verify Peer Certificate

field is set to Enable, and the server SSL certificate validation fails. If this happens, communication with the

ALMS server is terminated.

Corrective action

If you see this error message:

Check to see that you have a valid URL in the Server URL field.

In ACEmanager, go to Admin > Advanced and check the Date and Time field to confirm that the values are correct.

The SSL certificates have a start and end date. If the device has a date and time outside of this interval, the certification check will fail.

Contact your IT Administrator, or if you want the traffic to go through without verifying the server certificate, change the setting in the

Services > ALMS >

SSL Verify Peer Certificate field (described on page 151

) to

Disable.

ALMS Server Errors

[AVMS] HTTP error '500' ALMS server reported error 500 in the HTTP response.

Refer to the available ALMS server documentation for a list of all possible error codes and their significance.

Error message indicating a failure when parsing a valid ALMS server response

XML processing error The content of a valid ALMS server response cannot be parsed.

ALMS server responses are malformatted.

Contact ALMS support a

a. ALMS technical support: https://issues.m2mop.net

b. If the values are not correct and the device is not receiving date and time from the Mobile Network Operator or GPS, go to Services > Time (SNTP), and enable time update. For the SNTP Server, use the same service as the authenticating server.

When I try to update the radio module using ALMS, I receive an error message.

The following table provides a brief explanation of the firmware update error messages.

Error message

Cannot Install Firmware

Link not up in 3 minutes...Exiting

Meaning Corrective action

The system has encountered errors from which it cannot recover and requires at least a reboot before trying to update again.

Reboot the device.

If the problem persists, press the reset button for 7–10 seconds to reset the device to the factory default settings (release the reset button when all four LEDs turn from red to yellow) and try again.

If it still does not work, contact

ALMS support a

The radio module was not able to establish the connection in 3 minutes. The update has been aborted, but can be relaunched as soon as the connection is OK.

Wait for network connectivity and then try again.

442 4118967

Q & A and Troubleshooting

Error message

Unable to download JUD file from <url>

Core version not found in

JUD file

The URL is wrong, or the download failed

(interruption, no space left...).

JUD file is not valid. Core Version is a mandatory field.

Meaning Corrective action

Contact ALMS support a

Required information (URL,

Size or MD5) is missing from

JUD file

Cannot perform upgrade —

No space left on device

JUD file is not valid. URL, Size, and MD5 sum of the firmware package are mandatory fields.

Firmware is larger than available space for the download.

There is a problem with the package on the ALMS server. Contact ALMS support a

Contact ALMS support a

. The support team will need to access the device to clear space, or you can return the device to Sierra Wireless under an

RMA.

Unable to download ALEOS firmware from <url>

Undefined ALEOS firmware

URL

Firmware URL is not valid, or the download failed.

ALEOS firmware URL not specified, so firmware cannot be retrieved.

There is a problem with the package on the ALMS server. Contact ALMS support a

Retry. If the download fails several times, contact ALMS support a

. The support team will need a log from the device.

Contact ALMS support a

to confirm that there is not a problem with the service.

ALEOS firmware MD5 check failed

The downloaded firmware package failed the integrity check. The update is aborted.

There is a problem with the package on the device or the download may have failed. Restart the firmware download. If the problem persists, contact ALMS support a

. There may be a problem with the package on the ALMS server.

Unable to apply ALEOS firmware and Unable to apply

ALEOS firmware (retry)

ALEOS firmware could not be applied. Check the ALEOS log messages to determine exactly why the update failed.

Retry. If the problem persists, contact

ALMS support a

and provide them with the log messages.

Radio Module URL is missing from JUD file

Radio Module package MD5 sum is missing from JUD file

JUD file is not valid. The Radio Module

Firmware URL is a mandatory field.

JUD file is not valid. The Radio Module

Firmware MD5 sum is a mandatory field.

There is a problem with the package on the ALMS server. Contact ALMS support a

Radio Module firmware MD5 check failed

The downloaded firmware package failed the integrity check. The update is aborted.

Radio Module backup failed The radio module was saved to prevent a power failure. If the firmware cannot be backed-up on persistent storage, the firmware update will not proceed because of the risk that the radio module update will not be able to finish if interrupted.

There is a problem with the package on the device or the download may have failed. Try downloading the file again. If the problem persists, contact ALMS support a

. There may be a problem with the package on the ALMS server.

Contact ALMS support a

. The support team will need to access the device to clear space, or you can return the device to Sierra Wireless under an

RMA.

Rev 4 Jun.16

443

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Error message

Radio Module firmware download failed

Meaning Corrective action

Firmware URL is not valid, or download failed. Retry several times. If the problem persists, contact ALMS support a

. The support team will need a log from the device.

Undefined Radio Module firmware URL

Radio Module firmware update failed

The URL cannot be retrieved. The update is aborted.

Radio module firmware could not be applied.

Check the ALEOS log messages to determine exactly why the update failed.

Retry. If the problem persists, contact

ALMS support a

Retry. If the problem persists, contact

ALMS support a

a. ALMS technical support: https://issues.m2mop.net

GPS

I set the GPS Reports Port field on the GPS > Local Streaming page to stream GPS data to a USB port, but I don't see GPS data on the

USB port.

The GPS streaming feature works with serial devices. To stream data to a USB port, you must first configure the USB port to act as a serial device.

In ACEmanager, go to the LAN > USB tab.

In the USB Device Mode field, select USB Serial.

Click Apply.

If you have not already done so:

Go to GPS > Local Streaming.

In the GPS Reports port field, select one of the following:

· USB Serial

· DB9 and USB

Click Apply.

After you have made all the configuration changes, reboot the device.

Event Reporting

I set up ACEmanager to send an email/SMS report, but when I clicked the Test report button no report was sent.

After you set up the event reporting fields and click Apply, wait about a minute before you click the Test report button. The AirLink gateway needs this time to apply the new configuration.

I configured event reporting, but I did not receive a report when I should have.

•

If the Action Type for the Event Reporting is Email or SNMP TRAP, be sure that these services are also configured on the Services tab.

· To configure email, go to Services > Email (SMTP).

444 4118967

Q & A and Troubleshooting

· To configure SNMP TRAP, go the Services > Management (SNMP).

•

If the Action Type is SMS, you may need to change the default settings in the

Advanced section of the Services > SMS page.

TCP Connections

I went to the TCP section of the Serial screen and configured ALEOS to include the Device ID in TCP connections, but I get the message “Device ID Not Set”.

Setting the TCP connection to include the Device ID is a two step process:

In ACEmanager, go to Serial > TCP and ensure that the Include Device ID on

TCP Connect field is set to Enable.

(See

Port Configuration on page 247.)

Go to GPS > Global Settings > General and configure the Use Device ID in

Location Reports field. (See Global Settings on page 208.)

To confirm that the Device ID is configured, check the Status > About screen. The

Device ID, if set, appears in the GPS/RAP Device ID field.

TCP/IP and UDP/IP Auto Answer

I configured TCP/UDP auto answer, but the packet contents are not being streamed over the serial port to the connected device.

Try polling the device connected to the AirLink gateway’s serial port.

If you do not receive a response, confirm that the fields described in Configuring IP to Serial with Answer and Serial to IP on page 262 are set correctly.

In ACEmanager, go to Status > Serial and check the Serial bytes sent field to confirm that packets are reaching the AirLink gateway from the mobile network and the packet contents are being sent out the AirLink gateway’s serial port.

Rev 4 Jun.16

Figure F-3: ACEmanager: Status > Serial

445

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

When you poll the AirLink gateway/connected device:

•

If the Serial bytes sent counter increases, the IP packets have reached the

AirLink gateway from the mobile network, the AirLink gateway has removed the header and sent the packet contents out its serial port to the connected device.

•

If the Serial bytes sent counter does not increase, either:

· The IP packet has not made it across the mobile network to the AirLink gateway.

· The destination port for the TCP/IP or UDP/IP connection does not match the configured Device Port on the ACEmanager Serial tab.

Once you have confirmed that the Serial bytes sent counter is increasing, check the Serial bytes received counter (also on the Status > Serial screen).

· If the Serial bytes received counter is increasing, the connected device is responding to the poll request and sending its response back to the AirLink gateway across the serial connection.

· If the Serial bytes received counter is not increasing, the connected device is not responding to the poll request. Ensure that the serial cable is fully seated and properly connected to the AirLink gateway and the host. Check that you have the correct type of serial cable connecting the AirLink gateway to the connected device. The AirLink gateway is a DCE device. If the connected device is also a DCE device, use a null modem serial cable.

If the connected device is a DTE device, use a straight through serial cable.

If you have confirmed that both the Serial bytes sent and Serial bytes received counters are increasing when you send a poll to the connected device, but you are still not receiving the response back on your original sending application, the most common reason is that the incoming packets from the AirLink gateway to your application are being blocked by a firewall on your network. The firewall may be blocking all traffic except packets destined for particular ports or arriving from particular ports.

Check with your firewall administrator. Ask the administrator to monitor the firewall when you poll the AirLink/connected device to see if any return packets from the AirLink gateway hit the firewall.

If you are still having problems, contact your Sierra Wireless distributor.

ALEOS Application Framework (AAF)

I’m unable to load an application from AAF.

In ACEmanager, go to Services > Telnet/SSH.

In the AT Server Mode field, select Telnet.

Click Apply.

Re-try loading the application from AAF.

446 4118967

Q & A and Troubleshooting

Network Operator Switching

What happens to my Radio Module Firmware settings (Admin >

Radio Module Firmware) when I reset the gateway to the factory default settings?

If the Reset Mode field on the Admin > Advanced screen is set to “Preserve

Cellular Authentication Settings” (default setting), the Radio Module settings on the Admin > Radio Module Firmware screen are preserved over the reset, i.e. there is no change to the settings.

If the Reset Mode field on the Admin > Advanced screen is set to “Reset All”, then the settings on the Admin > Radio Module Firmware screen revert are reset. The

Automatic option is reset to “Automatic” and the ALMS option is reset to “Update

Current Only”. If you have previously selected a radio module firmware version manually that does not match the SIM card, “Reset All” may change the radio module firmware because once the gateway reverts to “Automatic”, which SIM card is installed in the gateway determines which radio module firmware is used.

This could override a previous manual selection.

Rev 4 Jun.16

447

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

448 4118967

Rev 4 Jun.16

G: Glossary of Terms

Acronym or Term

1xEV-DO

3GPP

API

CDG

CDMA cdmaOne

Definition

Single Carrier ( 1X ) EVolution–Data Only

A high-speed standard for cellular packet data communications. It supports Internet connections with data rates up to 3.1

Mbps . (downlink from the network) and 1.8

Mbps (uplink to the network). Average data rates are approximately:

•

Rev. A: 600-1300

kbps . (downlink from the network) and 300-400 kbps (uplink

to the network)

•

Rev. 0: 400-700 kbps (downlink from the network) and 40-80 kbps (uplink to the network)

Actual speed depends on the network conditions. Compare to

1X .

Single Carrier (1X) Radio Transmission Technology

A high-speed standard for cellular packet data communications.

1x supports Internet connections with data rates up to 153 kbps (simultaneously in

each direction—downlink and uplink). Actual speed depends on the network conditions. Compare to

1xEV-DO .

3 rd

Generation Partnership Project

3GPP unites 6 telecommunications standard development organizations (ARIB,

ATIS, CCSA, ETSI, TTA, TTC), and provides their members with a stable environment to produce Reports and Specifications that define 3GPP technologies.

Programming Interface

A protocol intended to be used as an interface by software components to communicate with each other.

A set of device commands, preceded by “AT” originally developed by Hayes, Inc. for their devices.

The structure (but not the specific commands, which vary greatly from manufacturer to manufacturer) is a de facto device industry standard.

CDMA Development Group

A consortium of companies who joined together to lead the adoption and evolution of CDMA wireless systems around the world.

Also see

CDMA .

Code Division Multiple Access

A wideband spread spectrum technique used in digital cellular, personal communications services, and other wireless networks.

Wide channels (1.25 MHz) are obtained through spread spectrum transmissions, thus allowing many active users to share the same channel. Each user is assigned a unique digital code, which differentiates the individual conversations on the same channel.

A IS-95 CDMA standard developed by QUALCOMM Inc.

Also known as TIA-EIA-95.

449

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Acronym or Term

CE, CE Label

CnS

DCE

Diversity

DMNR

EDGE

EIA

EMC

EMI

ERP

ESN

Ethernet

Definition

The CE label is a mandatory conformity marking for products placed on the market in the European Economic Area (EEA).

With the CE marking on a product, the manufacturer declares that the product conforms with the essential requirements of the applicable EC directives.

Sierra Wireless’ proprietary Control and Status protocol interface

Data Communications Equipment

A device that sits between the data terminal equipment (DTE) and a data transmission circuit. Usually the DCE is a modem.

Antenna diversity, also called space diversity, is a scheme that uses two or more antennas to improve the quality and reliability of a wireless link.

Often, especially in urban and indoor environments, there is no clear line-of-sight

(LOS) between transmitter and receiver. Instead the signal is reflected along multiple paths before finally being received. Each bounce can introduce phase shifts, time delays, attenuations, and distortions that can destructively interfere with one another at the aperture of the receiving antenna.

Dynamic Mobile Network Routing

Enhanced Data rates for GSM Evolution

A digital mobile phone technology that allows improved data transmission rates as a backward-compatible extension of GSM. EDGE is considered a pre-3G radio technology and is part of ITU's 3G definition.

Also known as Enhanced GPRS (EGPRS), or IMT Single Carrier (IMT-SC), or

Enhanced Data rates for Global Evolution.

Electronics Industry Association

EIA was a standards and trade organization composed as an alliance of trade associations for electronics manufacturers in the United States.

They developed standards to ensure the equipment of different manufacturers was compatible and interchangeable. The EIA ceased operations on February 11, 2011, but the former sectors continue to serve the constituencies of EIA.

Electromagnetic Compatibility

The branch of electrical science which studies the unintentional generation, propagation and reception of electromagnetic energy with reference to the unwanted effects (Electromagnetic interference, or EMI) that such energy may induce.

Electromagnetic Interference

The disturbance that affects an electrical circuit due to either electromagnetic induction or electromagnetic radiation emitted from an external source

Effective Radiated Power

A standardized theoretical measurement of radio frequency (RF) energy. It is determined by subtracting system losses and adding system gains.

Electronic Serial Number

The unique first-generation serial number assigned to the Air Link devices for use on the wireless network. Compare to

MEID .

Computer networking technologies for local area networks (LANs).

The European Union Organization of European countries.

450 4118967

Glossary of Terms

Acronym or Term

EVDO

FCC

GPRS

GSM

HSPA

HSPA+

IEC

IOTA

Definition

Enhanced Voice-Data Optimized or Enhanced Voice-Data Only (Ev-DO, EV,

EVDO, etc.).

A telecommunications standard for the wireless transmission of data through radio signals, typically for broadband Internet access. It uses multiplexing techniques including code division multiple access (CDMA) as well as time division multiplexing (TDM) to maximize both individual users' throughput and the overall system throughput.

Federal Communications Commission

The U.S. federal agency responsible for interstate and foreign communications.

The FCC regulates commercial and private radio spectrum management, sets rates for communications services, determines standards for equipment, and controls broadcast licensing.

Firmware

Software stored in ROM or EEPROM; essential programs that remains even when the system is turned off. Firmware is easier to change than hardware but more permanent than software stored on disk.

General Packet Radio Service

A packet-oriented mobile data service on 2G and 3G cellular communication systems.

GPRS was originally standardized by European Telecommunications Standards

Institute (ETSI) in response to the earlier CDPD and i-mode packet-switched cellular technologies. It is now maintained by the 3rd Generation Partnership

Project (3GPP).

Global System for Mobile Communications (originally Groupe Spécial Mobile)

GSM is a standard developed by the European Telecommunications Standards

Institute (ETSI) to describe protocols for second generation (2G) digital mobile networks used by mobile phones

High Speed Packet Access

An amalgamation of two mobile telephony protocols: High Speed Downlink Packet

Access (HSDPA) and High Speed Uplink Packet Access (HSUPA).

This extends and improves the performance of existing 3rd generation mobile telecommunication networks utilizing the WCDMA protocols.

Also called evolved HSPA

This allows bit-rates to reach as high as 168 Mbit/s in the downlink and 22 Mbit/s in the uplink. An improved 3GPP standard.

Industry Canada

The government department responsible for overseeing and regulating wireless and communication technologies in Canada.

International Electrotechnical Commission

A non-governmental international standards organization that prepares and publishes International Standards for all electrical, electronic and related technologies – collectively known as “electro technology.”

Internet Over The Air

An mated feature, supported by some service providers, to perform account setup by making a connection to the CDMA network and using a secure Internet connection to download account parameters to the device.

Rev 4 Jun.16

451

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Acronym or Term

IS-95

ISAKMP

ITU kbps

LED

LTE

Mbps

MEID

MSCI

NAM

OEM

OTAPA

OTASP

Definition

Interim Standard

After receiving industry consensus, the

TIA/EIA

forwards the standard to ANSI for approval.

A 2G mobile telecommunications standard using CDMA to send voice, data and signaling data (such as a dialed telephone number) between mobile telephones and cell sites.

Internet Security Association and Key Management Protocol

A security protocol defined by RFC 2408 for establishing Security Associations

(SA) and cryptographic keys in an Internet environment. ISAKMP only provides a framework for authentication and key exchange and is designed to be key exchange independent.

International Telecommunication Union

A specialized agency of the United Nations responsible for issues that concern information and communication technologies.

The ITU coordinates the shared global use of the radio spectrum, promotes international cooperation in assigning satellite orbits, and assists in the development and coordination of worldwide technical standards.

Kilobits per second

1000, not 1024, as used in computer memory size measurements of kilobytes.

Light Emitting Diode

A semiconductor diode that emits visible or infrared light.

Long Term Evolution

High performance air interface for cellular mobile communication systems.

Millions of bits per second, or Megabits per second.

Mobile Equipment IDentifier

The unique second-generation serial n umber assigned to the device for use on the wireless network. Compare to

ESN

Modem Status Configuration Interface

ALEOS internal configuration database

Number Assignment Module

Semi-permanent information stored in the device’s non-volatile memory, including the device’s Mobile Identification Number, the station class mark, Mobile Network

Operator code, and other cellular identifiers.

Essentially the phone number, it should be treated as confidential information and should not be disclosed to anyone other than the cellular service provider.

Non-Volatile (memory)

Original Equipment Manufacturer

A company that manufactures a product and sells it to a reseller.

Over the Air Parameter Administration

A way of distributing new software updates or configuration settings to devices like cellphones and set-top boxes.

Over the Air Service Provisioning. Also see

OTAPA

452 4118967

Glossary of Terms

Acronym or Term

PAD

PCS

PPP

PRI

Definition

Packet Assembly/Disassembly

Personal Communications Services

A cellular communication infrastructure that uses a different frequency range than

AMPS.

Point to Point Protocol

An alternative communications protocol used between computers, or between computers and routers on the Internet. PPP is an enhanced SLIP. Also see

SLIP

Product Release Instructions

A file containing the settings used to configure devices for a particular service provider, customer, or purpose.

RoHS

RS-232

SIM, SIM Card

SINR

SKU

SLIP

SMS

TCH

Radio Frequency

Restriction of use of Hazardous Substances mandated by EU Directive 2002/95.

A series of standards for serial binary single-ended data and control signals connecting between a DTE (Data Terminal Equipment) and a DCE (Data Circuitterminating Equipment). It is commonly used in computer serial ports.

Receive

Subscriber identity module or subscriber identification module.

An integrated circuit which securely stores the international mobile subscriber identity (IMSI) and the related key used to identify and authenticate subscribers on mobile telephony devices (such as mobile phones and computers).

Signal to Interference plus Noise Ratio (SINR) is an RF parameter that is directly proportional to throughput (the higher the number, the higher the throughput). It can help LTE radio installers gauge the signal quality between the cell tower and the radio module. For more information on interpreting the SINR values, see

How do I obtain and interpret SINR values for LTE networks?

on page 428.

Stock Keeping Unit

Identifies an inventory item: a unique code, consisting of numbers or letters and numbers, assigned to a product by a retailer for purposes of identification and inventory control.

Serial Line Internet (or Interface) Protocol

An Internet Protocol designed to work over serial ports and modem connections.

On personal computers, SLIP has been largely replaced by the Point-to-Point

Protocol (PPP), which has more features and does not require its IP address configuration to be set before it is established. On microcontrollers SLIP is still the preferred way of encapsulating IP packets due to its very small overhead.

Also see

PPP .

Short Message Service

A feature which allows users of a wireless device on a wireless network to receive or transmit short electronic alphanumeric messages (up to 160 characters, depending on the service provider).

Traffic Channel

Rev 4 Jun.16

453

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

Acronym or Term

TIA / EIA

UMTS

USB

VRRP

X.509

Definition

Telecommunications Industry Association / Electronics Industry Association

A standards setting trade organization, whose members provide communications and information technology products, systems, distribution services and professional services in the United States and around the world.

Transmit

Universal Mobile Telecommunications System (UMTS).

A third generation mobile cellular system for networks based on the GSM standard.

Developed and maintained by the 3GPP (3rd Generation Partnership Project),

UMTS is a component of the International Telecommunications Union IMT-2000 standard set and compares with the CDMA2000 standard set for networks based on the competing cdmaOne technology.

Universal Serial Bus

An industry standard defining the cables, connectors and communications protocols used in a bus for connection, communication and power supply between computers and electronic devices.

Virtual Router Redundancy Protocol

A Public Key Infrastructure (PKI) and Privilege Management Infrastructure (PMI) are standards that specify formats for public key certificates, certificate revocation lists, attribute certificates, a certification path validation algorithm, etc.

454 4118967

Index

A

ACEmanager

configuring

description

idle timeout, set

ALEOS Application Framework troubleshooting

, 446 unable to load application from , 446

using

, 276

ALEOS software update

, 22

ALMS auto synchronize

configuration

always on connect

analog inputs channel configuration

transformed values

APN backup

status

AT Commands

Applications > Data Usage

, 411, 415

GPS > Server 1 - Server 4 , 393

I/O > Current State

, 411

LAN > DHCP/Addressing , 377

Security > Trusted IPs - Inbound , 379, 384

Serial > Port Configuration

Services > Low Power

Status > Home

using

authentication general information

TACACS+

Auto DHCP

B

Bands, LTE

, 427

bandwidth throttle

, 72

browser support , 15

C

configuration

logging

serial

services

VPN

connection not working

, 426

custom SSL certificate , 153

D

data usage , 267

Dead Peer Detection , 127

device status (about) , 55

Device Status Screen configuring

, 203

DHCP Options

, 92

DHCP/Addressing , 88

Dial-up Networking , 303

digital inputs

RV50

DMNR

DMZ

DNS alternate port

dynamic

global

DNS proxy

documentation

domain name

DUN operating systems supported

, 303 setting up , 303

Dynamic Mobile Network Routing See DMNR

E

EC/IO

Engine Hours

Ethernet status

Ethernet Link Setting , 99

Ethernet port, enable and disable

, 97

Rev 4 Jun.16

455

Ethernet ports

, 96

troubleshooting , 438

Extended Archiver , 293

F

firmware update , 22

G

Garmin

global DNS

Glossary

GPS

global settings , 208

local IP report , 224, 227

status , 52

streaming

, 444 troubleshooting , 444

GRE , 129

H

Host Interface Watchdog , 118

host port routing

, 34, 103

I

Idle timeout, ACEmanager

, 153

inbound ports used by ALEOS

, 431

Internal DHCP Server , 95

IP Logging

, 290

IP Manager , 164

IPsec , 122

K

keepalive

, 66

L

LAN

LDAP authentication

LED indicator for serial traffic , 247

LED Power Saving , 160

LEDs, above Ethernet port

, 438

Load Root Certificate

, 133

Local/Streaming

, 222, 225

Log, mark a section of the log

, 295

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50 logging

Extended Archiver

LTE Band Class field

M

MAC filtering , 147, 426

MIB (Management Information Base) , 329

Modbus , 261, 323

Modbus address list , 261

Modbus TCP/IP , 324

N

network connection, poor

, 426

network settings, retain over reset

, 294

Network State

, 38

Network Watchdog, disable

, 59

NMEA , 206

O

Over the Air (OTA) connections

, 34

P

password, change , 285

PCI compliance

, 35

ping, on demand , 290

port filtering

outbound

port forwarding

error message

troubleshooting

Power management , 154

PPP connection, configuring , 260

PPPoE , 107

Primary SIM

, 58

Programmable Logic Controller

, 324

public and private mode

, 87

pulse count , 281

R

radio band, selecting , 429

radio module firmware update , 22

radio passthru

, 295

RADIUS authentication , 200

RAP , 206

redundant server , 220

relay outputs , 280

Reliable Static Routing (RSR)

, 75

Remote Terminal Unit , 323

456 4118967

reset device, retain network settings , 294

reset, periodic and time of day

reverse telnet/SSH

RSRQ

RSSI

S

security configuration

serial

configuration

LED indicator

MTU

serial port port configuration

TCP

Serial port, disable , 248

services configuration

, 149

status , 50

Shutdown Delay after Ignition off , 155

SIM Slot 1, configuration

, 63

SIM Slot 2, configuration

, 65

SIM, active , 58

SIM, Primary , 58

Simple Network Management Protocol (SNMP)

SINR

SMS

Control Only mode

Gateway Only mode

M2M

Password

Password Only mode

password, default

troubleshooting

trusted phone number , 182

SMS Commands

SMS M2M

SMS message error

SNMP traps

SNTP

SSH

SSL tunnel

Rev 4 Jun.16

Status

Applications

Home

Serial

Services

VPN

WAN/Cellular

T

TACACS+ authentication

, 201

TAIP

, 206

TCP connection configuring

, 256

Device ID Not Set , 445

troubleshooting

template applying

saving a custom configuration as

, 17

test button, SMS/email

, 186

third party services

, 163

time (SNTP)

, 197

troubleshooting

ALEOS AF

, 446

ALMS error messages , 442

AVMS status messages , 441

Ethernet ports , 438

GPS , 444

LAN network

, 438

mark a section of the log

, 295

port forwarding

, 440

radio module firmware update

, 424

RSR , 430

SMS

, 440

software and radio firmware updates , 424

TCP connections , 445

VPN

wireless connection

trusted IPs inbound

Trusted Phone Number

U

UDP

Multiple Unicast

, 253

UDP connection configuring

, 258

update

ALEOS software

, 22

radio module firmware

, 22

USB drivers, installing , 102

Index

457

ALEOS 4.5.2 Software Configuration User Guide for AirLink RV50

USB port , 99

USB, disable

, 101

V

VLAN

VPN

GRE

IPsec

status

troubleshooting

458 4118967

Διαφήμιση