CBC LME17 User manual

1 Introduction and Package Contents

Introduction

Congratulations on your purchase. You can expect only the sharpest and most brilliant color images from this monitor.

Featuring easy to use OSD controls and built in speakers, you will find this monitor both easy to use and a pleasure to look at.

Please unpack the monitor with care, and verify that all the parts listed below are included. If any parts are missing, please contact with your local distributor.

Please save the packing box for possible future return for service.

Package Contents

• One LED Monitor

• 12V DC Adapter/Power cord

• D-Sub 15-pin VGA connector Cable

• User's Guide

Hardware Installation

The following sections in this guide give clear, step-by-step descriptions of the installation process and explain how to use the monitor for optimum results.

Please pay attention to the Regulations and Warnings Section of this user’s manual before setting up the display monitor. Failure to do so may inadvertently result in personal injuries or machine damage.

1

Specifications

Size 17” 19”

Output Interface

Input Interface

Output video

Speaker

Display Mode

AC power

Input power

Temperature

(BNC) x 2

(BNC) x 2, (VGA) x 1, (RCA) x 2 (PC Audio) x 1 , (HDMI) x 1

(BNC) x 2

1.5W x 2

Video 1/ Video 2/ VGA / HDMI

AC 100~240V 50/60Hz

12VDC 3.33A, 40 Watt Max

Operation: 0°~40°C , Storage:-10°~60°C

Power

Consumption

OSD Control

OSD Languages

20W max in on mode 25W max in on mode

Under 3W in Power Saving Mode (100 Vac)

Under 5W in Power Saving Mode (240 Vac)

Picture Mode, Contrast, Brightness, Color, Tint, Sharpness,

Color Temp, DNR

English, German, French, Italian, Spanish, Russian, Turkish,

Japanese, Polish

Auto Adjustment

De-interlace

Yes

Yes

Wall mount Yes (Optional) 75mm VESA mount

Accessories Manual, Power Adaptor, VGA cable

Safety

FCC, CE, ROHS

Tilt -5°~15°C

Humidity

10％~90％

Monitor scan

Horizontal frequency

Vertical frequency

VESA specifications

Pixel pitch

Pixel format

Response time

Color depth

Contrast ratio

Luminance of white

Viewing angle (H/V)

Display area

Microprocessor controlled

31kHz~65kHz

56Hz~75Hz

DPMS,DDC1/2B

0.264x0.264mm

1280x1024

5ms

0.294x0.294mm

1280x1024

5ms

8-bit;16,77,216 colors

10,000:1

300cd/m 2

10,000:1

300cd/m 2

Horizontal : 170° / 160° , Vertical -170° / 160°

337.9 x 270.3

(H x V)mm

376.3 x 301.06

(H x V)mm

Weight

(monitor only)

3.2 KGS 3.3 Kg

2

Timing

Item

Resolution

1 640x400@70

4

5

2

3

6

7

640x480@60

640x480@72

640x480@75

720x400@70

800x600@56

800x600@60

8

9

10

11

12

800x600@72

800x600@75

1024x768@60

1024x768@70

1024x768@75

13 1280x1024@60

14 1280x1024@75

H Freq.(kHz)

31.460

48.077

46.875

48.363

56.476

60.023

63.981

79.976

31.469

37.861

37.500

31.460

35.156

37.879

V Freq.(Hz)

70.080

72.188

75.000

60.004

70.069

75.029

60.020

75.025

59.940

72.809

75.000

70.080

56.250

60.317

Note:

1. Please note, selecting frequencies outside these ranges may result in an abnormal images or damage to the monitor.

2. The resolution will be showed on the screen while VGA mode be selected.

For example:

3

Descriptions

The monitor displays PAL or NTSC standard color images in CCTV systems. 2 looping composite video BNC inputs, Audio input RCA, an analog VGA input using 15-pin D-sub, and an HDMI (High

Definition Multimedia Input) connector.

Features

– 17 inch plastic cased / metal cased models

– AC 100-240V Power Supply

– NTSC/PAL Auto Detect

– High Resolution Display 1280 x 1024

– VGA Input

– Composite Video Input

– HDMI Input

– On-screen Display (OSD) with Multiple Languages

– PIP / POP Function

Quick Installation

1. Connect power cord and power adaptor.

2. Connect video cable

• Make sure both the LED display and computer are turned off.

• Connect the video cable from the LED display to the computer.

3. Turn ON LED display and computer

4. Select input source

• Select the proper input source corresponding to the video

Signal, AV1/ AV2 / VGA / HDMI.

5. VGA mode only

• Press button Auto on front panel to automatically adjusts

H- Position, V-Position, Pixel Clock and Phase for an optimal

image.

4

2 Monitor and OSD Control

Monitor and OSD Control

The LED color monitor has a simple control layout for controlling the monitor and OSD (On Screen Display) functions. The table below summarizes the control keys and their related functions.

Keys Function Description

Toggle the display between standby mode and on.

(Press “Power” and waiting 6 sec., monitor will be display )

Automatically adjusts H-Position, V-Position, Pixel Clock and Phase for an optimal image in PC mode only.

Switch setting item.

Increase the value of the choose item.

Switch setting item.

Decrease the value of the choose item.

Select Source “PC”, ”AV1”, ”AV2”. (while in the OSD menu this button is used as select, advance and confirm)

Source Select

Enter the main menu of the on-screen display (OSD).

Press the select button to bring up source selection

Use the “ ”, “ ” keys to advance to the proper selection and press select button to confirm the setting.

5

Note:

The message will be displayed on the screen if there’s no VGA signal detected in VGA mode, and the power will be off automatically after 10 seconds. Please press the power button again to restart the monitor.

LED Status Display

The following table describes the various power states of the LED monitor as represented by different LED colors.

Power State

On

Standby

No power

LED Color

Green

Red

Blank

Note: The LED will also be red if AV1 or AV2 is selected and there is no video signal detected.

6

3 OSD Control Function List

OSD Menu

Main OSD function menu

Press on front panel to access OSD

Main menu functions as following:

Picture setup: Setup for overall image quality

Audio Setup: Setup of audio inputs

General Setup: Setup of basic sittings

PIP Setup: Setup for multiple signal display

Press the “ ”, “ ” keys to select the appropriate function then press the select button to access and to advance within that menu.

U se the “ ”, “ ” keys to change the parameter then press select button to confirm and advance to the next selection.

When the setting completed, press the menu button to return to the main menu. Press the exit OSD programming.

menu button again to

7

AV1/AV2 Mode –

Picture Mode

1. Picture Mode

2. Contrast

3. Brightness

4. Tint

5. Saturation

6. Sharpness

7. Color Temp.

8. DNR

Press “ ” OR “ ” to select the picture mode

“Movie, Vivid, User, Standard”

This is used to set the brightness of the screen.

Press “ ” OR “ ” to adjust the parameter.

This is used to adjust the image contrast.


This is used to adjust the image Tint.


This is used to adjust the image saturation.


Adjust the sharpness. It makes the image become soft.

Press “ ” OR “ ”” to adjust the parameter.

Press “ ” OR “ ” to adjust the color tones.

“ Cool , Warm , Normal “

Press “ ” OR “ ” to adjust the noise reduction.

“High , Low, Off, Mid “

8

Sound Mode

1. Volume Press “ ” OR “ ” to adjust volume level.

2. Mute Press “ ” OR “ ” to select sound “ Off, On ”.

9

Setting Mode

1. Language Press “ ” OR “ ” to select language.

2. H. Position

3. H Zoom

4. V Position

5. V Zoom

Move the display picture left or right.


Adjust the H-size of the display picture


Move the display picture up or down.


Adjust the V-size of the display picture


6. Scale Mode


Press “ ” OR “ ” to adjust “ Full, 16:9 ”.

7. Reset Recall Default value.

PIP/POP Setup Mode

1. Multi Window Press “ ” OR “ ” to select “PIP, POP,Off ” mode.

10

2. SubSource Press “ ” OR “ ” to select “AV, VGA” mode.

3. Size

4. Position

5. Border Color

Adjust the size of Sub Source window.

Press “ ” OR “ ” to select “Large, Small ”

Move the position of Sub Source window.

Press “ ” OR “ ” to select “U L, B L, B R, U R ” position.

Choose the border color of Sub Source window.

Press “ ” OR “ ” to select “Black, Blue” color.

6. Sound Source Press “ ” OR “ ” to select “Main, Sub” mode.

7. Swap Press “Select” to Swap the Source of Main and Sub.

Note:

AV1 and AV2 can not be displayed at the same time on the monitor in PIP / POP mode.

If POP mode is selected both images are scaled to fit the screen.

11

VGA Mode –

Picture Mode

1. Contrast

2. Brightness

3. Color Temp.

4. Auto Adjust







Select Auto Adjust to Auto synchronizes screen to graphics adaptor

12

Sound Mode



13

Setting Mode


2. H. Position

3. H Zoom

4. V Position

5. V Zoom

6. Clock










7. Phase Press “ ” OR “ ” to adjust the parameter.

8. Scale Mode




14


1. Multi Window Press “ ” OR “ ” to select “PIP, POP, Off ” mode.

2. SubSource Press “ ” OR “ ” to select “AV, VGA, HDMI” mode.

3. Size

4. Position

5. Border Color









Note:



15

HDMI Mode –

Picture Mode

1. Contrast

2. Brightness

3. Color Temp.

4. Auto Adjust







Select Auto Adjust to Auto synchronizes screen to graphics adaptor

16

Sound Mode



17

Setting Mode


2. H. Position

3. H Zoom

4. V Position







5. V Zoom



6. Scale Mode





1. Multi Window Press “ ” OR “ ” to select “PIP, POP, Off ” mode.

18

2. SubSource Press “ ” OR “ ” to select “AV, VGA, HDMI” mode.

3. Size

4. Position

5. Border Color









Note:



19

5 Mounting

VESA Bracket

Lay the LED display face down on a towel or blanket. Note the

4 screws that secure the hinge on the lower part of the back casing. These may be removed to release the desk mount bracket if required.

Attach a VESA compatible mounting bracket

(VESA 75mm x 75mm is supported)

4 screw for VESA 75mm

20

Dimensions:

21

6 Caring for Your LED Monitor

Caring for your LED Monitor

The LED color monitor is a sensitive piece of electronic equipment. Proper care can prevent accidentally damaging the LCD panel or the monitor itself. By following these guidelines you can ensure many years of trouble free use.

1. The LED monitor's plastic casing and LED glass panel can be cleaned with a soft, lint-free cloth. Never use scrub pads or

other cleaning materials with abrasive surfaces to clean your

LED monitor! a. For the plastic case, a mild detergent may be used to clean the surface. However, you should ensure not to use too much detergent or water as this could leak into the interior of the casing.

2. Do NOT use cleaning fluids based on alcohol, methylated spirit, or ammonia. The glass plate has a hard surface coating to prevent scratches. However, the use of strong chemical cleaning agents may damage this coating. Use only a mild soap or detergent and water or specially formulated cleaners made for cleaning glass panels.

3. Avoid direct contact with water or other liquids. Never use the LED monitor in or around areas where water may pose a potential hazard to normal operation.

4. Only use the LED monitor indoors, and avoid monitor contact with oil, vapor, steam, moisture and dust. The LED monitor should be used in a clean and low humidity environment.

5. Keep the LED monitor away from heaters or other heat sources such as lighting equipment or direct sunlight.

6. Keep the LED monitor away from sharp object to touch the screen like fingernail and pencil.

WARNING: Any unauthorized modification to this equipment could result in the revocation of the authorization to operate the equipment and void the product warranty.

22

7 Frequently Asked Questions

Power button does not respond

• Check the power cord to ensure that it is securely plugged into the monitor base and also into the electrical outlet.

• Ensure there is electrical power coming from the AC outlet.

Use another device to check for power.

• Unplug the power cord of the monitor from the AC outlet, wait a few minutes, then to plug the power cord into the AC outlet again. This will reset the monitor and power supply.

No image on the screen

• Ensure that the DB-15 signal cable is properly connected to the display card/computer.

• Check the DB-15 signal cable connector on both ends for bent or pushed-in pins.

• The display card should be properly seated in its card slot.

• Ensure that the computer's power switch is ON.

• Ensure that the monitor's power switch is ON.

•

Unplug the power cord of the monitor from the AC outlet, wait a few minutes, then to plug the power cord into the AC outlet again. This will reset the monitor and power supply.

Power LED is RED (with no image on the screen)

• Check the DB-15 signal cable to ensure that it is properly attached to the graphics display card.

• Check the DB-15 signal cable on both ends for bent or pushed-in pins.

• Make sure the computer is not in a power-saving mode

(move the mouse or press a key on the keyboard).

No sound coming from the audio speakers

• The audio cable should be connected to the lineout on the audio card and the line-in on the monitor. Ensure that the audio cable is properly connected.

• Inspect the audio cable for any apparent damage. Double check by switching to another audio cable to see if the audio works.

23

8 Regulations and Maintenance

FCC compliance

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generation, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Precautions

＊ Read all of these instructions and save them for later use.

＊ Follow all warnings and instructions on the product.

＊ Product

-

Do not cover or block the vent holes in the case.

24

-

Do not insert sharp objects or spill liquid into the LED monitor through cabinet slots. They may cause accident fire, electric shock or failure.

Disconnect the power plug from the AC outlet if you will not use it for an indefinite period of time.

-

Do not attempt to service this product yourself, as opening or removing covers may expose you to dangerous voltage potentials or other risks.

Do not touch the screen directly with your fingers. You may damage the screen, and oil from your skin is difficult to move.

Do not apply pressure to the screen. The LED is very delicate.

＊ Power

-

Use the type of power indicated on the marking label.

＊ Plugs

-

Do not remove any of the prongs of the monitor’s three-pronged power plug.

-

Disconnect the power plug from the AC outlet under following conditions:

◎ If you will not use it for an indefinite period time.

◎ When the power cord or plug is damaged or frayed.

◎ If the product does not operate normally when the operation instructions are followed. Adjust only those controls that are covered by the operating instructions. Improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to normal operation.

◎ If the product has been dropped or the cabinet has been damaged.

◎ If the product exhibits a distinct change in performance, indicate a need for service.

＊ Power and extension cords

-

Do not allow anything to rest on the power cord.

-

Do not locate this product where persons will walk on her cord.

25

-

Use the proper power cord with correct attachment plug type. If the power source is 120 V AC, use a power cord that has UL and C-UL approvals. If the power source is a 240 V AC supply, use the tandem (T blade) type attachment plug with ground conductor power cord that meets the respective European country’s safety regulations, such as VDE for Germany.

-

Do not overload wall outlets or power cords. Ensure that the total of all units plugged into the wall outlet does not exceed 10 amperes.

-

Ensure that the total ampere rating of all units plugged into the extension cord is not over the cord’s rating.

-

If the power supply cord, which came with your monitor, is to be connected to the PC instead of the wall outlet, this equipment is to be used with UL/TUV approved computers with receptacle rated 100~240V

AC, 50/60Hz, 2.0A(minimum).

＊ Environment

-

Place the monitor on a flat and leveled surface.

-

Place the monitor in a well-ventilated place.

-

Keep the monitor away from:

Extremely hot, cold or humid places, places directly under sunlight, dusty surroundings, equipment that generate strong magnetic fields.

26

CBC LME17 User manual

1 Introduction and Package Contents

Introduction

Package Contents

Hardware Installation

Specifications

Timing

Item

Resolution

H Freq.(kHz)

V Freq.(Hz)

Descriptions

Features

1. Connect power cord and power adaptor.

2. Connect video cable

3. Turn ON LED display and computer

4. Select input source

5. VGA mode only

2 Monitor and OSD Control

Monitor and OSD Control

Keys Function Description

Source Select

LED Status Display

3 OSD Control Function List

OSD Menu

AV1/AV2 Mode –

Picture Mode

Sound Mode

Setting Mode

PIP/POP Setup Mode

VGA Mode –

Picture Mode

Sound Mode

Setting Mode

PIP/POP Setup Mode

HDMI Mode –

Picture Mode

Sound Mode

Setting Mode

PIP/POP Setup Mode

5 Mounting

VESA Bracket

Attach a VESA compatible mounting bracket

Dimensions:

6 Caring for Your LED Monitor

Caring for your LED Monitor

7 Frequently Asked Questions

Power button does not respond

No image on the screen

Power LED is RED (with no image on the screen)

No sound coming from the audio speakers

8 Regulations and Maintenance

FCC compliance

Precautions

Related manuals

Speco Technologies

VM17 LED/VM19 LED

Premier Accessory Group

ZJVP01

INMOTION

inM417

Syscom Video

EPMON23LED

IISONIC

IIMJ7

TruVue

75369

CBC

LME22

Mace

MAC-MON-17LED

Hi Sharp

HS-ML1002

Vigilant Vision

DSMH26LED-WGF

Vigilant Vision

DSMH32WGF