advertisement
Combi B 30 mit Metall-Eingabeeinheit
Bedienungsanleitung
Version DE + EN
DE
Bedienungsanleitung 82132/3xxx CB 30
Inhaltsverzeichnis
Stand 26.08.2016
Seite 2 von 48
Bedienungsanleitung 82132/3XXX - Combi B 30
Tabellenverzeichnis
Abbildungsverzeichnis
Stand 26.08.2016
Seite 3 von 48
Bedienungsanleitung 82132/3xxx CB 30
1 Wichtige Hinweise
Lesen Sie bitte vor Inbetriebnahme des Schlosses diese Bedienungsanleitung sorgfältig durch und beachten
Sie die folgenden Hinweise:
Der mitgelieferte Revisionsschlüssel erlaubt auch bei Codeverlust den vollen Zugriff auf das Schloss und seine
Konfigurationen. Er ist somit die höchste Hierarchiestufe des Schlosses. Er ist daher unbedingt an einem sicheren
Ort, jedoch auf keinen Fall im Wertbehältnis aufzubewahren.
Programmiervorgänge und Batteriewechsel sollten aus Sicherheitsgründen unbedingt bei geöffnetem Wertbehältnis durchgeführt und anschließend überprüft werden.
Jede korrekte und vom Schloss anerkannte Tastenbetätigung wird mit einem akustischen Signal bestätigt.
Für jede einzelne Tasteneingabe haben Sie max. 10 Sekunden Zeit. Wenn innerhalb dieser 10 Sekunden keine Taste bedient wird, schaltet sich die Elektronik automatisch ab. Nicht beendete Bedienungen müssen danach neu gestartet werden. Ausgenommen hiervon sind lediglich die Codestatus-Abfrage sowie der Programmiermodus mit 30 Sekunden
Reaktionszeit bis zum automatischen Abschalten.
Codeeingaben bzw. alle weiteren Funktionen (z.B. Programmierungen) können bis zum letzten Tastendruck durch zweimaliges Drücken der Taste abgebrochen werden.
Verwenden Sie für Ihren Code keine persönlichen oder ähnliche bekannte sowie leicht zu erratende Daten.
Sofern der/die eingestellte(n) Code(s) nicht verfügbar ist/sind, kann das Schloss über den mitgelieferten Revisionsschlüssel geöffnet oder zurückgesetzt werden.
Das Schloss ist zur Nutzung im Temperaturbereich von +10° C bis +50° C und einer Luftfeuchtigkeit von 30% bis 80%
(nicht kondensierend) ausgelegt.
Das Schloss darf unter keinen Umständen gefettet werden oder mit anderen Gleitmitteln oder aggressiven Flüssigkeiten in
Berührung kommen, die Reinigung darf nur mit einem feuchten Tuch erfolgen (keine aggressiven Reinigungsmittel)
Öffnen Sie niemals das Schlossgehäuse. Demontieren Sie den Beschlag nur zum Zweck des Batteriewechsels und genau entsprechend den Vorgaben dieser Bedienungsanleitung. Meiden Sie die Berührung elektronischer Komponenten.
Ansonsten gefährden Sie die Funktionen des Schlosses und verlieren den Gewährleistungsanspruch.
Bei der Inbetriebnahme wird die Seriennummer der Eingabeeinheit im Auditspeicher des Schlosses hinterlegt. Ein Wechsel der Eingabeeinheit wird ebenso mit einem Eintrag im Auditspeicher des Schlosses vermerkt.
Bei jeder Beschreibung von Bedien- bzw. Programmiervorgängen wird im Folgenden davon ausgegangen, dass sich das
Schloss und die Eingabeeinheit im Grundzustand befinden. Grundzustand bedeutet, das Schloss ist geschlossen (der
Schlossriegel ist ausgefahren) und die Schlosselektronik ist abgeschaltet. Sollten Sie sich nicht sicher sein, ob das Schloss geschlossen ist, so prüfen Sie bitte, ob sich der Drehknopf gegen den Uhrzeigersinn drehen lässt. Um sicher zu gehen, dass sich das Schloss nicht in einem laufenden Programmiervorgang befindet, können Sie 2 mal die Taste drücken, um diesen abzubrechen.
Das Schloss ist bei Auslieferung von Kaba Mauer GmbH auf den Monteurcode „1“ eingestellt. Aktivieren Sie aus
Sicherheitsgründen sofort den Mastercode mit Ihrem persönlichen Code, um den Monteurcode zu deaktivieren.
Der Monteurcode ist nur zur Montage des Schlosses und nicht zur weiteren, dauerhaften Verwendung geeignet.
Das Schloss bietet darüber hinaus die Möglichkeit einer Teil- oder Komplettinbetriebnahme durch den Tresorhersteller oder
–händler:
Bei einer Teilinbetriebnahme werden bereits Grundkonfigurationen am Schloss eingespielt, ohne den Mastercode zu aktivieren. Das Schloss öffnet also weit erhin mit „1“. Erst nach der Aktivierung des Mastercodes
Bei Komplettinbetriebnahme wurde das Schloss bereits mit einem Mastercode und ggf. weiteren Einstellungen versehen.
In beiden Fällen wird Ihnen die eingestellte Grundkonfiguration separat durch den Tresorhersteller oder
–händler mitgeteilt. Falls eine Komplettinbetriebnahme durchgeführt und damit ein Mastercode als Auslieferungscode voreingestellt wurde, kann der Tresorhersteller oder
–händler diesen zusätzlich im folgenden schraffierten Textfeld hinterlegen.
Alle vorkonfigurierten Codes sind sofort nach Inbetriebnahme durch den Endnutzer umzustellen.
Vom Händler bzw. Tresorhersteller eingestellter Mastercode (Auslieferungscode):
0 0 _ _ _ _ _ _
Hinweis für Endanwender:
Stellen Sie sämtliche Ausliefercodes sofort um!
Falls noch weitere Codes vorbelegt wurden, siehe separate Information des
Tresorhändlers bzw. -herstellers.
Stempel des Tresorherstellers/ -händlers
Stand 26.08.2016
Seite 4 von 48
Bedienungsanleitung 82132/3XXX - Combi B 30
2 Abkürzungs- und Begriffsverzeichnis
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
Code:
ID:
PIN:
Bediener:
Mastercode:
Benutzercode:
Kuriercode:
Monteurcode:
ÖV:
ÖBZ:
Sperrzeit:
Doppelcode:
Stiller Alarm:
EMA:
Numerische Reihe von 8 Ziffern zur Identifikation des Bedieners bestehend aus ID und
PIN. feststehende 2 stellige Bedienernummer. frei wählbare 6 stellige Ziffernkombination (Achtung, keine persönlichen Daten wie z.B. Geburtstage verwenden). der Master, die Benutzer und der Kurier sind Bediener des Schlosses
– jedem Bediener des Schlosses ist eine eigenständige ID (00, 01..30; 95) zugewiesen.
ID 00; höchster Code der Codehierarchie, kann das Schloss öffnen, den eigenen Code
ändern und wird für fast alle Programmierfunktionen des Schlosses benötigt. Kann auch im Doppelcode-Modus alleine Programmierfunktionen durchführen.
ID 01 bis 30, kann das Schloss öffnen und den eigenen Code ändern.
ID 95, kann das Schloss öffnen, ohne eine ggf. programmierte Öffnungsverzögerung abzuwarten und den eigenen Code ändern. hat keine ID, kann während der Montage im Werk das Schloss öffnen.
Öffnungsverzögerung: einstellbare Zeit, die ablaufen muss, bevor das Schloss geöffnet werden kann.
Öffnungsbereitschaftszeit: einstellbare Zeit, die nach der Öffnungsverzögerung beginnt;
Innerhalb der ÖBZ kann das Schloss geöffnet werden.
Nach 3-maliger falscher Codeeingabe wird die Sperrzeit aktiviert, innerhalb der Sperrzeit sind keine Eingaben am Schloss möglich.
Es werden zwei unterschiedliche gültige Codes benötigt, um das Schloss zu öffnen.
Ist das Schloss an eine externe Alarmanlage (Einbruchmeldeanlage) angeschlossen und ist diese Funktion am Schloss aktiviert, kann ein stiller Bedrohungsalarm (für den
Aggressor nicht wahrnehmbar) ausgelöst werden.
Einbruchmeldeanlage: externe Alarmanlage, für die Auswertung/Weitergabe des
Bedrohungsalarmes oder einer gesicherten Permanentspannungsversorgung (nicht im
Lieferumfang enthalten).
Unterspannungsanzeige: Anzeige, dass die Batterien erschöpft sind, und so bald wie möglich ausgewechselt werden müssen, um eine sichere Funktion des Schlosses zu gewährleisten.
AHK:
Audit:
Abhebekontakt: Ein Kontakt in der Eingabeeinheit, der registriert, ob die Eingabeeinheit geöffnet wurde (z.B. zum Batteriewechsel).
Alle relevanten Ereignisse (Öffnungen, Schließungen, Programmierungen etc.) werden im Auditspeicher (ca. 200 Ereignisse) des Schlosses abgelegt. Ist der Speicher voll, wird
Zurücksetzen:
Revisionsschlüssel: der älteste Eintrag automatisch überschrieben. Das Audit kann mit einer Software ausgelesen werden.
Zurücksetzen des Schlosses in den Auslieferungszustand, nur der Mastercode und das
Audit bleiben erhalten.
Mit dem Revisionsschlüssel kann das Schloss unabhängig von der Elektronik jederzeit mechanisch geöffnet werden. Bei der Schlüsselöffnung gibt es keine ÖV oder Sperrzeit.
Ebenso kann mit dem Revisionsschlüssel der Mastercode neu vergeben und das komplette Schloss zurückgesetzt werden. Schließlich kann mit Hilfe des
Revisionsschlüssels und der Software eine Neukonfiguration des Schlosses umgesetzt werden, ohne dabei den Mastercode zu kennen oder zu ändern. Daher liegt der
Revisionsschlüssel in der Codestruktur über dem Mastercode und ist an einem sicheren
Ort (nicht im Wertbehältnis) aufzubewahren.
Stand 26.08.2016
Seite 5 von 48
Bedienungsanleitung 82132/3xxx CB 30
oder
Tabelle 1: Symbole
3 In der Anleitung verwendete Symbole
Symbol Bedeutung
Warnung
Wichtig
Hinweis
Symbol für 2-stellige Code ID (siehe auch Kapitel 2)
Symbol für einzelne Zifferntasten bei der Codeeingabe
Aktion durchgeführt
Aktion nicht durchgeführt
Betätigungsknopf 90° im Uhrzeigersinn drehen
Betätigungsknopf 90° gegen den Uhrzeigersinn drehen
Kurzsignal LED grün
Dauersignal LED grün
LED grün aus
Kurzsignal LED rot
Dauersignal LED rot
LED rot aus
Signal Summer
Stand 26.08.2016
Seite 6 von 48
Bedienungsanleitung 82132/3XXX - Combi B 30
4 Schloss-System: Eingabeeinheit und Schloss
Ein komplettes Schloss-System besteht aus einer sichtbaren Eingabeeinheit und dem im Wertbehältnis eingebauten Schloss.
Sämtliche programmierten Codes und Funktionen werden ausschließlich im Schloss und damit im gesicherten Bereich gespeichert.
4.1 Bedienelemente der Eingabeeinheit
Betätigungsknopf Tastatur
Tastatur:
1 rote und 1 grüne LED
Zifferntasten
P-Taste
Bestätigungstaste
Abbildung 1: Eingabeeinheit Abbildung 2: Mini-USB Buchse
Sonderschnittstelle, nur in
Verbindung mit Original
Kaba Mauer CB30
PC-Kabel verwenden!
4.2 Schlossgehäuse und Schnittstellen
Verbindung mit weiteren
Komponenten (z.B. EMA)
Spannungsversorgung
Verbindung mit der
Eingabeeinheit
Abbildung 3: Schlossgehäuse Abbildung 4: Anschlüsse am Schlossgehäuse
Stand 26.08.2016
Seite 7 von 48
Bedienungsanleitung 82132/3xxx CB 30
5 Berechtigungsübersicht
Die Berechtigungen der einzelnen Bediener sehen wie folgt aus:
Bediener-
ID
Code-
Bezeichnung
Berechtigung
-
00
01..30
95
Revisionsschlüssel
Mastercode
Benutzercodes
Kuriercode
- Öffnen ohne ÖV/ÖBZ und ohne Sperrzeiten
- Mastercode neu vergeben
- Schloss zurücksetzen
- Schlosskonfigurationen über Software ändern, ohne den
Mastercode zu kennen oder zu ändern.
- Öffnen, bei Bedarf mit Stillem Alarm
- eigenen Code ändern
- Benutzer und Kurier aktivieren, sperren, entsperren, löschen, auch bei aktiviertem Doppelcode
- Doppelcode aktivieren, deaktivieren
- ÖV/ÖBZ programmieren/löschen
- Abhebekontakt neutralisieren
- Audit auslesen
- Stillen Alarm aktivieren, deaktivieren
- Zugriff über PC-Software
- Öffnen, bei Bedarf mit Stillem Alarm
- eigenen Code ändern
- Öffnen ohne ÖV/ÖBZ, bei Bedarf mit Stillem Alarm
- eigenen Code ändern
- Monteurcode
- Öffnen
- Nur bis zur echten Inbetriebnahme des Schlosses gültig,
KEIN ECHTER CODE, nicht zur dauerhaften Verwendung geeignet
Tabelle 2: Berechtigungen
6 Übersicht über die Programmierbefehle
Aktion
Eigenen Code ändern
Audit auslesen
ÖV/ÖBZ aktivieren + deaktivieren
Benutzer aktivieren
Benutzer sperren + entsperren
Benutzer löschen
Codestatus-Abfrage
Doppelcode aktivieren + deaktivieren
Stillen Alarm aktivieren + deaktivieren
Abhebekontakt-Meldung quittieren
Zurücksetzen des Schlosses
Neuvergabe des Mastercodes
Tabelle 3: Programmierbefehle
Befehl Berechtigung
P
P1
P2
P7
P8
P9
P0
P
P3
P4
P5
P6 jeder
Master
Schlüssel
Stand 26.08.2016
Seite 8 von 48
Bedienungsanleitung 82132/3XXX - Combi B 30
7 Übersicht der möglichen Signale
Ereignis Wann Signal
Taste drücken (z.B. Codeeingabe)
Code gültig (Code-Richtig-Meldung)
Korrekte Eingabe
Fehlermeldung (z.B. Code ungültig)
wiederholende Eingabe (z.B. Codebestätigung) nicht
übereinstimmend
Abbruch (Manueller Abbruch mit oder zeitgesteuerter Abbruch durch Ausbleiben von Eingaben)
Bei jedem
Tastendruck
Nach Eingabe
Enter
Nach Eingabe
Enter
1 x
2 x und 2 x
3 x und 3 x
Abhebekontakt wurde aktiviert
Sperrzeit
Doppelcode; Eingabe des zweiten Codes wird erwartet
ÖV
ÖBZ
Unterspannung
Programmiermodus
Fernsperre aktiviert, keine Öffnung möglich
3 x nach
Eingabe Enter
Permanent nach Eingabe
Enter
Permanent nach Eingabe
Enter
Permanent nach Eingabe
Enter
Permanent nach Eingabe
Enter
Nach Eingabe
Enter
Permanent nach Eingabe
Enter
Bei jedem
Tastendruck
1 x und 1 x , dann
1 x und 1 x
1 x , dann 0,5s Pause
1 x , dann 2s Pause
1 x , dann 5s Pause
1 x und 1 x , dann 5s
Pause
10 x
1 x
1 x
und
Hardwarefehler. Bitte Service kontaktieren.
Keine Verbindung zum Schloss!
Kabelverbindung prüfen (Stecker am Schlo ss in „input unit“?)
Beschlagoberteil nicht korrekt/ unvollständig aufgeschoben?
Codestatus Meldungen
Nach Eingabe
Enter
Nach
Aufschieben des Beschlagoberteils
3s und 3s
Dauer
Code aktiv
1 x und 1 x
Code aktiv, aber gesperrt
Nach Eingabe
Enter
1 x , 1 x und 1 x
Code gelöscht bzw. inaktiv
Tabelle 4: Meldungen vom Schloss, Begriffe siehe Kapitel 2, Symbole siehe Kapitel 3
1 x und 1 x
Stand 26.08.2016
Seite 9 von 48
Bedienungsanleitung 82132/3xxx CB 30
8 Inbetriebnahme des Schlosses
Der Schlosseinbau sowie die Verkabelung und der erste Batterieeinbau sind in der Installationsanleitung beschrieben.
Solange das Schloss-System nicht in Betrieb genommen wurde, lässt es sich mit dem Monteurcode öffnen.
Der Monteurcode dient zu Montagezwecken im Werk und nicht zur weiteren, dauerhaften Verwendung!
Monteurcode ungültig wird.
Wurde die Inbetriebnahme bereits durch einen Tresorhersteller oder -händler durchgeführt, so finden Sie die entsprechenden Angaben in dessen Anleitungen/Hinweisen. Darüber hinaus kann der Tresorhersteller bzw. -händler in dieser Anleitung den eingestellten Mastercode dokumentieren. Hierzu beachten Sie bitte den grau unterlegten Bereich in
„Vom Händler bzw. Tresorhersteller eingestellter Mastercode“.
8.1 Öffnen mit Monteurcode
Beschreibung
1. Drücken Sie und 2x 2x 3x 3x
2.
Drehen Sie den Betätigungsknopf innerhalb von 4 Sekunden im Uhrzeigersinn um 90° bis zum
Anschlag . Öffnen Sie nun das Behältnis.
Tabelle 5: Öffnen mit Monteurcode
Solange der Monteurcode zum Öffnen genutzt wird (Master noch nicht aktiviert), gibt es keine Sperrzeit bei fehlerhaften
Codeeingaben gemäß Kapitel 10.5 und auch keine Abhebekontakt Signalmeldung gemäß 9.6
8.2 Master aktivieren
Aktivieren Sie nun bei geöffnetem Behältnis (um jederzeit Zugriff auf das Behältnis und das Schloss zu haben) den Master.
Beschreibung
1. Drücken Sie und
2x 3x 3x
2. Geben Sie den neuen Mastercode
(00 = ID, X = frei gewählte 6-stellige Ziffernkombination [0..9])
und ein
2x 3x 3x
3. Bestätigen Sie den neuen Mastercode mit und 2x 2x 3x 3x
Tabelle 6: Master aktivieren
Überprüfen Sie die erfolgte Programmierung im Anschluss bei weiterhin geöffnetem Behältnis. Gehen Sie dabei nach Kapitel
Sollte das Code-Falsch-Signal erfolgen, muss die Prozedur wiederholt werden, da die beiden Codes nicht
übereinstimmen oder die ID (hier 00) falsch eingegeben wurde.
Die Änderung des Mastercodes kann jederzeit durch zweimaliges Drücken von abgebrochen werden. Alternativ wird der Vorgang abgebrochen, wenn 30 Sekunden lang keine Eingabe erfolgt.
9 Programmierfunktionen für den Master
Alle hier beschriebenen Programmierfunktionen benötigen den Mastercode zur Ausführung.
Programmierungen und Überprüfungen von Programmierungen sollten aus Sicherheitsgründen immer bei geöffnetem
Wertbehältnis durchgeführt werden (um jederzeit Zugriff auf das Behältnis und das Schloss zu haben).
Programmierungen sind jederzeit individuell und ohne Wartezeiten ausführbar (Ausnahme Sperrzeiten), auch wenn
Doppelcode und/oder ÖV/ÖBZ aktiviert sind. Alle Programmiervorgänge können durch zweimaliges Drücken von abgebrochen werden. Alternativ wird die Eingabe abgebrochen, wenn 30 Sekunden lang keine Eingabe erfolgt.
Stand 26.08.2016
Seite 10 von 48
Bedienungsanleitung 82132/3XXX - Combi B 30
9.1 Mastercode ändern (P)
Nach der Umstellung des Mastercodes ist der vorherige Mastercode nicht mehr gültig. Der neue Mastercode ist bei geöffnetem
Wertbehältnis mittels Schlossöffnung auf Funktion zu prüfen (siehe Kapitel 10.1)!
Beschreibung
1. Drücken Sie
und geben Sie den aktuellen Mastercode
(00 = ID, X = bisher programmierte 6-stellige Ziffernkombination)
und ein
2x 3x 3x
und ein
2. Geben Sie den neuen Mastercode
(00 = ID, Y = neue 6-stellige Ziffernkombination)
2x 3x 3x
3. Bestätigen Sie den neuen Mastercode mit und 2x 2x 3x 3x
Tabelle 7: Mastercode ändern
Der gesamte Vorgang ist in den folgenden Fehlerfällen zu wiederholen:
Erscheint nach Eingabe des aktuellen Codes gemäß 1. das Code-Falsch-Signal, wurde der Code falsch eingegeben.
Erfolgt nach der zweiten neuen Codeeingabe wie unter 3. das Code-Falsch-Signal, so stimmen die beiden neuen unter
2. bzw. 3. eingegebenen Codes nicht überein.
9.2 Funktionen für weitere Codes programmieren (P3-P6)
In diesem Abschnitt werden grundlegende Programmiervorgänge für weitere Codes (Benutzer- bzw. Kuriercodes) beschrieben.
Mastercode direkt am Schloss eine Abfrage über den Status der einzelnen Codes durchführen kann.
Zur korrekten Nutzung des Schlosses muss der Mastercode aktiviert sein (siehe Kapitel 8.2).
9.2.1 Benutzercodes oder Kuriercodes aktivieren (P3)
Ein Code ist erst nach einer vorigen Aktivierung nutzbar. Bei der Aktivierung eines weiteren Bedieners ist es sinnvoll, dass der neue Code (ab Punkt 3 der folgenden Beschreibung) direkt vom betreffenden Bediener vor Ort eingegeben wird. Sollte der neue Code nicht direkt vom Bediener eingegeben, sondern vom Master vorgegeben worden sein, muss dieser schnellstmöglich
Beschreibung
1. Drücken Sie
und geben Sie den gültigen Mastercode
(00 = ID, X = gültige 6-stellige Ziffernkombination für den Master)
und ein
2x 3x 3x
2. Drücken Sie und ein 2x 3x 3x
3. Geben Sie den neuen Code
und ein
(ID = 01 bis 30 für Benutzer bzw. 95 für Kurier, X = frei gewählte 6-stellige Ziffernkombination [0..9])
2x 3x 3x
4. Bestätigen Sie den neuen Code mit und 2x 2x 3x 3x
Tabelle 8: Code aktivieren
Nach der Aktivierung ist der neu hinterlegte Code gültig und kann verwendet werden. Der neue Code ist mittels Schlossöffnung
zu überprüfen (siehe Kapitel 10.1)!
Stimmen die beiden eingegebenen Codes nicht überein, erfolgt nach der zweiten Codeeingabe das Code-Falsch-Signal.
In diesem Fall muss der gesamte Vorgang wiederholt werden. Erscheint nach der ersten Codeeingabe das Code-Falsch-
Signal ist der Code bereits aktiv oder nicht verfügbar. Wiederholen Sie den Vorgang mit einem gültigen und nicht aktivierten Code.
Stand 26.08.2016
Seite 11 von 48
Bedienungsanleitung 82132/3xxx CB 30
9.2.2 Benutzercodes oder Kuriercodes sperren (P4)
Löschen bleibt der Code beim Sperren unverändert im Schloss gespeichert und kann durch erneutes Entsperren wieder verwendet werden.
Beschreibung
1. Drücken Sie
und geben Sie den gültigen Mastercode
(00 = ID, X = gültige 6-stellige Ziffernkombination für den Master)
und ein
2x 3x 3x
2. Drücken Sie und 2x 3x 3x
3. Geben Sie die zu sperrende ID
(ID = 01 bis 30 für Benutzer bzw. 95 für Kurier)
und ein
2x 2x 3x 3x
Tabelle 9: Code sperren
Erscheint nach Schritt 3 das Code-Falsch-Signal, so ist die ID entweder nicht aktiviert oder nicht verfügbar. Wiederholen
Sie den Vorgang mit einem gültigen und aktivierten Code.
Fehlt beim Bestätigungssignal lediglich die rote LED, wurde der Code nicht gesperrt, sondern entsperrt, weil er zuvor bereits gesperrt war! Den gesamten Vorgang erneut durchführen, um den Code erneut zu sperren.
Ein Sperren des Mastercodes ist nicht möglich.
9.2.3 Benutzercodes oder Kuriercodes entsperren (P4)
Nach dem Entsperren eines zuvor gemäß 9.2.2 gesperrten Codes ist dieser wieder verwendbar.
Beschreibung
1. Drücken Sie
und geben Sie den gültigen Mastercode ein
(00 = ID, X = gültige 6-stellige Ziffernkombination für den Master)
und
2x 3x 3x
2. Drücken Sie und 2x 3x 3x
3. Geben Sie die zu entsperrende ID
(ID = 01 bis 30 für Benutzer bzw. 95 für Kurier)
und ein
2x 2x 3x 3x
Tabelle 10: Code entsperren
Erscheint nach Schritt 3 das Code-Falsch-Signal, so ist die ID entweder nicht aktiviert oder nicht verfügbar. Wiederholen
Sie den Vorgang mit einem gültigen und aktivierten Code.
Erscheint zusätzlich zum normalen Bestätigungssignal die rote LED, wurde der Code nicht entsperrt, sondern gesperrt, weil er zuvor bereits entsperrt war! Den gesamten Vorgang erneut durchführen, um den Code erneut zu entsperren.
9.2.4 Benutzercodes oder Kuriercodes löschen (P5)
zu entsperren.
Beschreibung
1. Drücken Sie
und geben Sie den gültigen Mastercode
(00 = ID, X = gültige 6-stellige Ziffernkombination für den Master)
und ein
2x 3x 3x
2. Drücken Sie und 2x 3x 3x
3. Geben Sie die zu löschende ID
(ID = 01 bis 30 für Benutzer bzw. 95 für Kurier)
und ein
2x 2x 3x 3x
Tabelle 11: Code löschen
Erscheint nach Schritt 3 das Code-Falsch-Signal, ist die ID entweder nicht aktiviert oder nicht verfügbar. Wiederholen
Sie den Vorgang mit einem gültigen und aktivierten Code.
vergeben werden.
Stand 26.08.2016
Seite 12 von 48
Bedienungsanleitung 82132/3XXX - Combi B 30
9.2.5 Codestatus-Abfrage (P6)
In diesem Abfrageprogramm kann der Zustand jedes Codes (aktiv, gesperrt oder inaktiv bzw. gelöscht) abgefragt werden.
Weder die Codes noch deren Zustände werden dadurch geändert. Es können dabei die Zustände beliebig vieler IDs
nacheinander abgefragt werden. Die verschiedenen Codestati entnehmen Sie der Tabelle 13.
Beschreibung
1. Drücken Sie
und geben Sie den gültigen Mastercode
(00 = ID, X = gültige 6-stellige Ziffernkombination für den Master)
und ein
2x 3x 3x
2x 2x 3x 3x 2. Drücken Sie und
3.
Geben Sie nacheinander alle abzufragende(n) ID(s) und jeweils ein
Es erfolgt eine Codestatusmeldung pro ID gemäß Tabelle 13: Codestatusmeldungen
4.
Verlassen Sie den Abfragemodus durch Eingabe von .
Alternativ 30 Sekunden warten
Tabelle 12: Codestatus abfragen
Codestatus Meldung
3x 3x
3x 3x
(aktiv) 1x 1x
(aktiv, aber gesperrt) 1x 1x 1x
(gelöscht/inaktiv) 1x 1x
Tabelle 13: Codestatusmeldungen
9.3 Öffnungsverzögerung und Öffnungsbereitschaftszeit programmieren (P2)
Als Öffnungsverzögerung (ÖV) bezeichnet man die Zeit, nach deren Ablauf ein Öffnen des Schlosses möglich ist. Als
Öffnungsbereitschaftszeit (ÖBZ) bezeichnet man das Zeitfenster, während dessen das Schloss nach Ablauf der ÖV geöffnet werden kann. Mit diesem Programm werden die ÖV (01 bis 99 Minuten) und die ÖBZ (01 bis 19 Minuten) eingestellt bzw. gelöscht. Die eingestellten Zeiten gelten für alle Benutzer und den Master, aber nicht für den Kurier.
9.3.1 Öffnungsverzögerung und Öffnungsbereitschaftszeit aktivieren (P2)
Um eine Öffnungsverzögerung (ÖV) und eine Öffnungsbereitschaftszeit (ÖBZ) zu programmieren, gehen Sie wie folgt vor:
Beschreibung
1. Drücken Sie
und geben Sie den gültigen Mastercode
(00 = ID, X = gültige 6-stellige Ziffernkombination für den Master)
und ein
2x 3x 3x
2. Drücken Sie und 2x 3x 3x
3. Geben Sie die Öffnungsverzögerung
und die Öffnungsbereitschaftszeit
(XX = 01 bis 99, YY= 01 bis 19, Angaben jeweils in Minuten)
und ein
2x 2x 3x 3x
Tabelle 14: Öffnungsverzögerung und Öffnungsbereitschaftszeit programmieren
Erscheint nach der Eingabe Schritt 3 das Code-Falsch-Signal, liegen die eingegebenen Zeiten außerhalb des maximal zulässigen Bereichs. Das Code-Falsch-Signal erscheint auch, wenn entweder nur die ÖV oder nur die ÖBZ mit 00 angegeben werden. Beides ist nicht zulässig. Wiederholen Sie den Vorgang mit gültigen Werten für die ÖV und ÖBZ.
9.3.2 Öffnungsverzögerung und Öffnungsbereitschaftszeit deaktivieren (P2)
vorgehen und dabei die 2-stellige ÖV sowie die 2 stellige ÖBZ jeweils mit „00“ eingeben. Danach können alle Bediener das
Schloss ohne Verzögerung öffnen.
Stand 26.08.2016
Seite 13 von 48
Beschreibung
1. Drücken Sie
und geben Sie den gültigen Mastercode
(00 = ID, X = gültige 6-stellige Ziffernkombination für den Master)
2 Drücken Sie und
3. Geben Sie und ein
Tabelle 15: Öffnungsverzögerung und Öffnungsbereitschaftszeit löschen
9.4 Doppelcode programmieren (P7)
Bedienungsanleitung 82132/3xxx CB 30
und ein
2x 3x 3x
2x 3x 3x
2x 2x 3x 3x
Mit der Funktion Doppelcode wird das Schloss so eingestellt, dass zwei beliebige, jedoch unterschiedliche Codes
(unterschiedliche IDs) zum Öffnen des Schlosses benötigt werden. Der Doppelcode schließt alle Bediener (Master, Benutzer und Kurier) ein. Mit diesem Programmierbefehl wird der Doppelcode aktiviert bzw. deaktiviert.
9.4.1 Doppelcode aktivieren (P7)
Um den Doppelcode zu aktivieren, gehen Sie wie folgt vor:
Beschreibung
1. Drücken Sie
und geben Sie den gültigen Mastercode
(00 = ID, X = gültige 6-stellige Ziffernkombination für den Master)
und ein
2x 3x 3x
2. Drücken Sie und 2x 2x 3x 3x
Tabelle 16: Doppelcode aktivieren
Das Schloss kann nun nur noch wie unter 10.3 beschrieben geöffnet werden.
Um den Doppelcode zu aktivieren, müssen mindestens zwei Bediener mit gültigen Codes angelegt sein. Andernfalls erfolgt die Fehlermeldung beim Aktivieren des Doppelcodes.
Der Doppelcode muss deaktiviert sein, um ihn aktivieren zu können.
Erscheint zusätzlich zum normalen Bestätigungssignal die rote LED, war der Doppelcode zuvor bereits aktiviert und ist nun deaktiviert. Zum erneuten Aktivieren ist der komplette Vorgang zu wiederholen.
9.4.2 Doppelcode deaktivieren (P7)
Um den Doppelcode zu deaktivieren, gehen Sie wie folgt vor:
Beschreibung
1. Drücken Sie
und geben Sie den gültigen Mastercode
(00 = ID, X = gültige 6-stellige Ziffernkombination für den Master)
und ein
2x 3x 3x
2. Drücken Sie und 2x 2x 3x 3x
Tabelle 17: Doppelcode deaktivieren
Der Doppelcode muss aktiviert sein, um ihn deaktivieren zu können.
Fehlt beim Bestätigungssignal die rote LED, war der Doppelcode zuvor bereits deaktiviert und ist nun aktiviert.
Zum erneuten Deaktivieren ist der komplette Vorgang zu wiederholen.
Stand 26.08.2016
Seite 14 von 48
Bedienungsanleitung 82132/3XXX - Combi B 30
9.5 Stillen Alarm programmieren (P8)
Ein Stiller Alarm wird durch eine besondere Codeeingabe ausgelöst. Es handelt sich dabei um eine Alarmmeldung, die das
Schloss über einen Alarmausgang absetzt, während es sich weiterhin öffnen lässt. Um den Stillen Alarm weiterzuleiten, muss der Alarmausgang allerdings mit einer Einbruchmeldeanlage (nicht im Lieferumfang) verbunden sein (weitere Details erfahren
Sie in der Installationsanleitung und von einem Errichter von Einbruchmeldeanlagen). Mit diesem Programmierbefehl wird
Ist der Stille Alarm deaktiviert, werden die Alarmcodes als falsche Codes bestätigt und das Schloss öffnet nicht!
9.5.1 Stillen Alarm aktivieren (P8)
Um den Stillen Alarm zu aktivieren, gehen Sie wie folgt vor. Anschließend ist der Stille Alarm aktiviert und die Alarmcodes können verwendet werden.
Beschreibung
1. Drücken Sie
und geben Sie den gültigen Mastercode
(00 = ID, X = gültige 6-stellige Ziffernkombination für den Master)
und ein
2x 3x 3x
2. Drücken Sie und 2x 3x 3x
Tabelle 18: Stillen Alarm aktivieren
Der Stille Alarm muss deaktiviert sein, um ihn aktivieren zu können.
Erscheint zusätzlich zum normalen Bestätigungssignal die rote LED, war der Stille Alarm zuvor bereits aktiviert und ist nun deaktiviert. Zum erneuten Aktivieren ist der komplette Vorgang zu wiederholen.
9.5.2 Stillen Alarm deaktivieren (P8)
Um den Stillen Alarm zu deaktivieren, gehen Sie wie folgt vor. Anschließend ist der Stille Alarm deaktiviert, die Alarmcodes werden als falsche Codes bestätigt und das Schloss öffnet nicht mehr mit einem Alarmcode.
Beschreibung
1. Drücken Sie
und geben Sie den gültigen Mastercode
(00 = ID, X = gültige 6-stellige Ziffernkombination für den Master)
und ein
2x 3x 3x
2. Drücken Sie und 2x 2x 3x 3x
Tabelle 19: Stillen Alarm deaktivieren
Der Stille Alarm muss aktiviert sein, um ihn deaktivieren zu können.
Fehlt beim Bestätigungssignal die rote LED, war der Stille Alarm zuvor bereits deaktiviert und ist nun aktiviert. Zum erneuten Deaktivieren ist der komplette Vorgang zu wiederholen.
9.6 Abhebekontakt-Meldung quittieren (P9)
Das Schloss ist mit einem Abhebekontakt (AHK) ausgestattet, welcher beim Öffnen der Eingabeeinheit (z.B. zum Wechseln der
Batterie oder nach einer Manipulation) ausgelöst wird und anschließend bis zur Quittierung bei jeder Öffnung/Bedienung mit dem Manipulations-Signal ( und 3x im Wechsel + 6x ) angezeigt wird.
Mit diesem Programmierbefehl wird die Abhebekontakt-Meldung quittiert. Dieser Vorgang wird wie alle Vorgänge am Schloss im
Ereignisspeicher/Audit hinterlegt.
Sollte das o.g. Signal erscheinen, obwohl Sie vorher keinen Batteriewechsel durchgeführt haben, so besteht die Gefahr, dass die Eingabeeinheit z.B. zum Zweck des Code-Ausspähens manipuliert wurde. Bevor sie also diese Meldung quittieren, stellen Sie sicher, dass keine Manipulation an der Eingabeeinheit erfolgt ist. Wenn Sie sich unsicher sind, ob eine Manipulation vorliegt, ziehen Sie einen autorisierten Servicedienst hinzu!
Um die Abhebekontakt-Meldung zu quittieren und damit die Manipulationsanzeige abzuschalten, gehen Sie wie folgt vor:
Stand 26.08.2016
Seite 15 von 48
Beschreibung
Bedienungsanleitung 82132/3xxx CB 30
und ein
2x 3x 3x
1. Drücken Sie
und geben Sie den gültigen Mastercode
(00 = ID, X = gültige 6-stellige Ziffernkombination für den Master)
2. Drücken Sie und
Tabelle 20: Abhebekontakt-Meldung quittieren
10 Schlossfunktionen für alle Benutzer
2x 3x 3x
Jede Tasteneingabe von abgebrochen werden. Alternativ wird die Eingabe abgebrochen, wenn 10 Sekunden lang keine Eingabe erfolgt.
Wird
Batterien müssen möglichst bald gewechselt werden. Weitere Details finden sie in Kapitel 13.
Erscheint nach der Codeeingabe das Abhebekontaktsignal
Eingabeeinheit geöffnet. Lesen Sie dazu unbedingt Kapitel 9.6.
wurde die
Das Schloss verfügt über eine Funktion, die ein Ausspähen von Codes durch Beobachtung bei der Eingabe erschwert:
Bei sämtlichen Öffnungsvorgängen kann der Bediener seinen Code durch beliebig viele weitere Ziffern ergänzen, bevor er die Eingabe durch Drücken von abschließt. Alle Eingaben ab der 9. Stelle werden ignoriert. Achtung: Diese
Funktion unterstützt nur die der Codeeingabe zur Öffnung und steht bei Programmiervorgängen nicht zur Verfügung.
Öffnung mit aktivierten Zusatzfunktionen: Das Schloss verfügt über die Möglichkeit, weitere, durch Fremdsignale
ausgelöste Zusatzfunktionen auszuführen. Details hierzu entnehmen Sie bitte dem Kapitel 10.8.
10.1 Schloss öffnen ohne programmierte ÖV/ÖBZ
Beschreibung
1. Geben Sie einen gültigen Öffnungscode
und
(ID = 00 bis 30 bzw. 95, X = programmierte 6-stellige Ziffernkombination für die jew. ID Nummer)
ein
2x 2x 3x 3x
2. Drehen Sie den Betätigungsknopf innerhalb von 4 Sek. im Uhrzeigersinn um 90° bis zum Anschlag
Tabelle 21: Öffnen mit Master- oder Benutzercode
Ertönt nach Codeeingabe das Code-Falsch-Signal muss die Eingabe komplett wiederholt werden. Nach 3 fehlerhaften
Eingaben schaltet das Schloss in die Sperrzeit (siehe Kapitel 10.5).
10.2 Schloss öffnen bei programmierter ÖV/ÖBZ
Beschreibung
1.
2.
3.
Geben Sie einen gültigen Öffnungscode und ein
(ID = 00 bis 30 oder 95, X = programmierte 6-stellige Ziffernkombination für die jew. ID Nummer)
Sofern Sie hier einen Kuriercode eingegeben haben, fahren Sie direkt mit Schritt 4 fort.
Sofern Sie keinen Kuriercode eingegeben haben (ID 95), erscheint nun die Signalisierung für die ablaufende Öffnungsverzögerung (1x Pause). Diese ist vollständig abzuwarten.
Öffnungsbereitschaftszeit beginnt nach Ablauf der Öffnungsverzögerung (1x
Geben Sie nun erneut einen gültigen Öffnungscode
(ID = 00 bis 30, X = programmierte 6-stellige Ziffernkombination für die jew. ID Nummer)
Pause)
und ein
4. Drehen Sie den Betätigungsknopf innerhalb von 4 Sek. im Uhrzeigersinn um 90° bis zum Anschlag
Tabelle 22: Öffnen bei programmierter ÖV/ÖBZ
2x 2x 3x 3x
2x 2x 3x 3x
Stand 26.08.2016
Seite 16 von 48
Bedienungsanleitung 82132/3XXX - Combi B 30
Die laufende Öffnungsverzögerung kann jederzeit durch zweimaliges Drücken von abgebrochen werden.
Ertönt nach einer Codeeingabe das Code-Falsch-Signal muss die Eingabe komplett wiederholt werden. Nach 3
fehlerhaften Eingaben schaltet das Schloss in die Sperrzeit (siehe Kapitel 10.5).
Kuriercode:
Nach Eingabe des Kuriercodes (ID 95) kann unter Umgehung einer evtl. programmierten ÖV (Öffnungsverzögerung) sofort geöffnet werden (Schritte 2 und 3 entfallen).
Doppelcodemodus:
Im Doppelcodemodus ist bei Schritt 3 ein vollständiger Doppelcode gemäß 10.3 einzugeben.
Die ÖV wird dabei nur durch Eingabe eines einzelnen Codes gestartet.
Umgehung der ÖV/ÖBZ mit Kuriercode im Doppelcodemodus:
Um dies zu ermöglichen, muss im Doppelcodemodus der Kuriercode der erste eingegebene Code sein. Danach kann der zweite Code (nicht der Kuriercode) eingegeben und dann geöffnet werden.
Revisionsschlüssel:
Die ÖV kann durch die Verwendung des Revisionsschlüssels übergangen, aber nicht gelöscht werden (siehe Kapitel
10.3 Öffnen mit Doppelcode
Beschreibung
1. Geben Sie einen ersten gültigen Öffnungscode
(ID = 00 bis 30 oder 95, X = programmierte 6-stellige Ziffernkombination für die jew. ID Nummer)
und ein
2. Es erscheint nun die Signalisierung zur Eingabe des zweiten Codes (1x ; 2s Pause)
2x 2x 3x 3x
3. Geben Sie einen weiteren gültigen Öffnungscode
und ein
(ID = 00 bis 30 oder 95, jedoch anders als in Schritt 1, Y = programmierte 6-stellige Ziffernkombination für die jew. ID Nummer)
2x 2x 3x 3x
4. Drehen Sie den Betätigungsknopf innerhalb von 4 Sek. im Uhrzeigersinn um 90° bis zum Anschlag
Tabelle 23: Öffnen mit Doppelcode
Die Bediener-IDs der beiden Codes dürfen nicht übereinstimmen. Die Reihenfolge der Codeeingaben ist irrelevant, es
der Eingabe des ersten Codes das Code-Falsch-Signal, muss die Eingabe komplett wiederholt werden. Erfolgt erst nach der Eingabe des zweiten Codes das Code-Falsch-Signal, ist der zweite eingegebene Code falsch oder es ist der gleiche wie bei der ersten Eingabe (Identische ID). In beiden Fällen muss die Eingabe komplett wiederholt werden. Nach
ob die fehlerhafte Eingabe bei dem ersten oder dem zweiten Code erfolgt ist. Auch wenn die Fehleingaben abwechselnd bei dem ersten oder zweiten Code erfolgen, wird nach 3 fehlerhaften Eingaben in die Sperrzeit geschaltet.
10.4 Öffnen mit Stillem Alarm
eine Einbruchmeldeanlage (nicht im Lieferumfang) angeschlossen ist
– das Schloss unter gleichzeitiger Erzeugung eines Stillen
Alarmes geöffnet werden. Hierzu muss ein spezieller, von einem gültigen Code abgewandelter Alarmcode eingegeben werden
(bei aktiviertem Doppelcode genügt einer der beiden Codes). Bei Eingabe eines Alarmcodes öffnet das Schloss äußerlich wie immer, allerdings wird zusätzlich ohne weitere sichtbare/hörbare Rückmeldung ein Stiller Alarm abgesetzt.
Der Alarmcode besteht aus einem gültigen Code, bei welchem die letzte Stelle/Ziffer um eine Ziffer erhöht oder um eine Ziffer verringert wird (+1 oder -1; siehe Beispiele). Wenn die letzte Codeziffer eine 0 oder eine 9 ist, wird bei dem Alarmcode die vorletzte Stelle nicht verändert (siehe Beispiel 2). Wenn eine Öffnungsverzögerung programmiert ist, muss diese trotz Eingabe eines Alarmcodes abgewartet werden.
Ist der Stille Alarm deaktiviert, werden die Alarmcodes als falsche Codes bestätigt und das Schloss öffnet nicht bzw. die
ÖV wird nicht aktiviert!
Beispiele:
Normaler Code 00123459 Normaler Code 00123456
Alarmcode -1 00123458 Alarmcode -1 00123455
Alarmcode +1 00123457 Alarmcode +1 00123450
Tabelle 24: Alarmcode Beispiele
Stand 26.08.2016
Seite 17 von 48
Bedienungsanleitung 82132/3xxx CB 30
Öffnungsvorgang:
Beschreibung
1.
Geben Sie einen abgewandelten gültigen Öffnungscode als Alarmcode
und ein
(ID = 00 bis 30 oder 95, X = die ersten 5 Stellen der programmierten 6-stelligen Ziffernkombination für die jew. ID Nummer,
Y = um 1 erhöhte oder verminderte 6. Stelle der o.g. Kombination)
2x 2x 3x 3x
2. Drehen Sie den Betätigungsknopf innerhalb von 4 Sek. im Uhrzeigersinn um 90° bis zum Anschlag
Tabelle 25: Öffnen mit Alarmcode
Ertönt nach Codeeingabe das Code-Falsch-Signal, muss die Eingabe komplett wiederholt werden. Nach 3 fehlerhaften
Eingaben schaltet das Schloss auch hier in die Sperrzeit (siehe Kapitel 10.5)
Doppelcode:
Bei aktiviertem Doppelcode reicht es aus, einen der beiden Codes als Alarmcode einzugeben, um den Stillen Alarm zu aktivieren. Der Alarm wird aber erst aktiviert, wenn beide zum Öffnen notwendigen Codes vollständig eingegeben wurden.
10.5 Sperrzeit (3 oder mehr fehlerhafte Codeeingaben)
Nach 3 fehlerhaften Eingaben schaltet das Schloss in eine 1-minütige Sperrzeit. Bei jeder weiteren fehlerhaften Codeeingabe erfolgt eine Verlängerung der Sperrzeit auf 2, 4, 8 und schließlich auf 16 Minuten. Während der gesamten Sperrzeit ist keine weitere Codeeingabe möglich. Die Sperrzeit kann nur mit dem Revisionsschlüssel übergangen, jedoch nicht gelöscht werden
10.6 Schloss schließen
Betätigungsknopf gegen den Uhrzeigersinn um 90° bis zum Anschlag drehen . Eine Codeeingabe ist nicht erforderlich.
In Verbindung mit einem Riegelwerk (meist erkennbar durch einen zusätzlichen Drehgriff am Wertbehältnis) muss nach dem Schließen der Tür zunächst das Riegelwerk verriegelt werden. Erst danach kann das Schloss geschlossen werden.
Der sichere Verschluss des Schlosses ist durch versuchsweises Drehen des Knopfes an der Eingabeeinheit zu
überprüfen. Der Knopf darf sich dabei nicht mehr als ca. 45° drehen lassen.
10.7 Codes ändern (P)
Jeder ist berechtigt, seinen eigenen Code jederzeit zu ändern. Der Master ist nicht berechtigt, Benutzercodes oder den
Kuriercode zu ändern. Er kann aber Codes aktivieren, sperren, entsperren und löschen.
Nach der Umstellung ist der vorherige Code nicht mehr gültig und es muss der neue Code verwendet werden. Der neue Code
ist bei geöffnetem Wertbehältnis mittels Schlossöffnung auf Funktion zu prüfen (siehe Kapitel 10.1)!
Beschreibung
und ein
1. Drücken Sie
und geben Sie den aktuellen Code
(ID [00 bis 30 oder 95], X = programmierte 6-stellige Ziffernkombination für die jew. ID Nummer)
2. Geben Sie den neuen Code
und
(ID wie in Punkt 2, Y = neue 6-stellige Ziffernkombination für diese ID Nummer)
ein
2x 3x 3x
2x 3x 3x
3. Bestätigen Sie den neuen Code mit und 2x 2x 3x 3x
Tabelle 26: Code ändern
Der gesamte Vorgang ist in den folgenden Fehlerfällen zu wiederholen:
Erscheint nach Eingabe des aktuellen Codes gemäß 1.das Code-Falsch-Signal, ist der Code falsch oder nicht vergeben und kann somit nicht geändert werden.
Erscheint nach der ersten neuen Codeeingabe wie unter 2. das Code-Falsch-Signal, stimmt die ID nicht mit der aus
Schritt 1 überein. Die ID muss auch bei einer Codeänderung immer beibehalten werden!
Erfolgt nach der zweiten neuen Codeeingabe wie unter 3. das Code-Falsch-Signal, so stimmen die beiden neuen unter
2. bzw. 3. eingegebenen Codes nicht überein.
Stand 26.08.2016
Seite 18 von 48
Bedienungsanleitung 82132/3XXX - Combi B 30
10.8 Öffnung bei aktivierten Zusatzfunktionen
Das Schloss verfügt über besondere Zusatzfunktionen (jeweils nur eine davon möglich), welche nur mittels der optionalen PC-
Software eingestellt werden können. Sollte eine dieser Funktionen aktiviert sein, so verhält ich das Schloss anders als vorher beschrieben: a) Fernsperre:
Ist die Funktion "Fernsperre" aktiviert und liegt ein entsprechendes Eingangssignal an, wird jede Taste mit 1x quittiert. Es ist also keine Eingabe möglich. b) Übersteuerung der ÖV/ÖBZ:
Hier werden evtl. programmierte Öffnungsverzögerungszeiten und dazugehörige Öffnungsbereitschaftszeiten
übersteuert. c) Übersteuerung des Doppelcodes:
Bei dieser Funktion wird ein evtl. programmierter Doppelcode zum Einfachcode. Der sonst erforderliche zweite Code entfällt. d) Unterlassungsalarm:
Wenn diese Funktion am Schloss aktiviert ist, muss maximal 60 Sekunden vor einer Codeeingabe ein separates
Eingangs-Signal erzeugt werden (z.B. durch einen versteckten Taster), ansonsten erzeugt das Schloss - anders als
in 10.4 beschrieben - trotz korrekter Codeeingabe eines Stillen Alarms.
11 Schlüsselfunktionen
11.1 Schlüsselöffnung
Die Öffnung des Schlosses mit dem Revisionsschlüssel ist ausschließlich für den Notfall und nicht für den Dauereinsatz vorgesehen. Wenden Sie beim Öffnen mit dem Schlüssel keine Gewalt an! Sie könnten dadurch das Schloss zerstören.
Zur Schlüsselöffnung muss der Drehgriff des Schlosses demontiert werden. Da der Drehgriff in 90 ° Schritten aufgesteckt werden kann, merken Sie sich bitte zunächst die Stellung des Drehgriffes für den anschließenden Zusammenbau (z.B. mittels eines Klebestreifens auf der Eingabeeinheit, der die Position der Markierung auf dem Drehgriff wiedergibt). Stecken Sie nun den beiliegenden Inbusschlüssel in das kleine Loch an der Seitenwand der Eingabeeinheit bis zum Anschlag (siehe Abb. 5.1) ein. Den Drehgriff nun nach vorne aus der Eingabeeinheit herausziehen (siehe Abb. 5.2) und den Inbusschlüssel entfernen.
Anschließend die Vierkantwelle aus dem Schloss herausziehen (siehe Abb. 5.3). Jetzt kann der Schlüssel wie in Abb. 5.4 dargestellt (Schlossgehäuse waagerecht und Riegel links angenommen) ins Schloss eingeführt werden. Sollte die Einbaulage des Schlosses nicht bekannt sein, können Sie die korrekte Ausrichtung des Schlüssels durch Probieren in 90° Schritten ermitteln. Alternativ fragen ihren Servicetechniker oder Schrankhersteller. Den Schlüssel nach dem korrekten Einführen zur
Schlossöffnung um ca. 150° nach rechts bis zum Anschlag drehen (siehe Abb. 5.5). Das Schloss ist nun geöffnet. Nach
Abschluss der Schlüsselöffnung die Eingabeeinheit wieder in umgekehrter Reihenfolge wie oben beschrieben montieren und den Schlüssel an einem sicheren Ort, jedoch nicht im Wertbehältnis aufbewahren.
Schlüssel ist in der Offenposition des Schlosses nicht abziehbar.
Abb. 5.1: Position Drehgriff (Markierung) merken. Inbusschlüssels in kleines Loch bis zum Anschlag eindrücken.
Abb. 5.2: Abziehen des Drehgriffes nach vorne, dabei Inbusschlüssel gedrückt halten.
Abb. 5.3: Inbusschlüssel entfernen und
Vierkantwelle herausziehen.
Abb. 5.4: Schlüssel einführen.
Abbildung 5: Schlüsselöffnung
Abb. 5.5: Schlüssel im Uhrzeigersinn bis zum Anschlag drehen.
Stand 26.08.2016
Seite 19 von 48
Bedienungsanleitung 82132/3xxx CB 30
11.2 Verschließen mit dem Schlüssel
Den Schlüssel gegen den Uhrzeigersinn um ca. 150° bis zum Anschlag drehen, abziehen und vor dem Zugriff Unbefugter schützen (nicht innerhalb des Wertbehältnisses). Anschließend die Vierkantwelle mit dem Ende der Bohrung voran ins Schloss stecken (siehe Abb. x) und den Drehknopf wieder so orientiert aufstecken, wie er vor der Demontage war (hierzu dient die unter
entfernt werden.
11.3 Mastercode mit dem Schlüssel ändern (P)
Mit diesem Programmierbefehl wird der Mastercode geändert, ohne den Mastercode zu kennen. Dies ist hilfreich, wenn der
Mastercode nicht mehr verfügbar ist, die übrigen Einstellungen des Schlosses jedoch nicht geändert werden sollen.
Dieser Programmierbefehl kann nur ausgeführt werden, während das Schloss mit dem Schlüssel geöffnet ist. Der neue
Mastercode ist mittels Schlossöffnung bei geöffnetem Behältnis auf Funktion zu prüfen!
Beschreibung
1. Öffnen Sie das Schloss mit dem Schlüssel (siehe Kapitel 11.1)
2. Drücken Sie und
2x 3x 3x
3. Geben Sie den neuen Mastercode
(00 = ID, X = frei gewählte, 6-stellige Ziffernkombination 0..9)
und ein
2x 3x 3x
2x 2x 3x 3x 4. Bestätigen Sie den neuen Mastercode und eingeben
5.
Das Schloss wieder mit dem Schlüssel verschließen (11.2), Drehgriff montieren (11.1) und den
Mastercode bei geöffnetem Behältnis testen (10.1 bis 10.4)
Tabelle 27: Mastercode mit dem Schlüssel ändern
Stimmen die beiden eingegebenen Codes nicht überein, erfolgt nach der zweiten Codeeingabe das Code-Falsch-Signal.
Erscheint nach der ersten Codeeingabe das Code-Falsch-Signal, ist die ID falsch. Die ID muss bei der Mastercode-
änderung immer „00“ sein!
Der Vorgang kann jederzeit durch zweimaliges Drücken ohne Änderung abgebrochen werden. Alternativ wird die
Änderung abgebrochen, wenn 30 Sekunden lang keine Eingabe erfolgt oder das Schloss während der Umstellung mit
dem Schlüssel wieder verschlossen wird (siehe Kapitel 11.2).
11.4 Zurücksetzen des Schlosses (P0)
Mit diesem Programmierbefehl wird das Zurücksetzen des Schlosses durchgeführt. Dies bedeutet, dass durch diesen Vorgang alle Einstellungen des Schlosses gelöscht werden (Benutzercodes, Kuriercode, Doppelcode, Stiller Alarm, Öffnungsverzögerung und Öffnungsbereitschaftszeit), lediglich der Mastercode und das Audit bleiben erhalten.
Dieser Programmierbefehl kann nur ausgeführt werden, während das Schloss mit dem Schlüssel geöffnet ist.
Stand 26.08.2016
Seite 20 von 48
Bedienungsanleitung 82132/3XXX - Combi B 30
Beschreibung
1. Das Schloss mit dem Schlüssel öffnen (siehe Kapitel 11.1)
2. Drücken Sie und
3. Drücken Sie und
2x 3x 3x
2x 2x 3x 3x
4. Das Schloss wieder mit dem Schlüssel verschließen (11.2) und Drehgriff montieren (11.1)
Tabelle 28: Zurücksetzen des Schlosses
Der Vorgang kann jederzeit durch zweimaliges Drücken von abgebrochen werden. Alternativ wird die Änderung abgebrochen, wenn 30 Sekunden lang keine Eingabe erfolgt oder das Schloss vor Schritt 3 wieder mit dem Schlüssel
verschlossen wird (siehe Kapitel 11.2).
11.5 Neukonfiguration des Schlosses nach Schlüsselöffnung mittels Software
Nähere Details zur Vorgehensweise entnehmen Sie bitte der Bedienungsanleitung für die PC-Software.
Neukonfiguration des Schlosses möglich, und zwar ohne Kenntnis oder Änderung des Mastercodes. Es erfolgt lediglich ein Auditeintrag.
12 Weitere Sonderfunktionen
12.1 Verbindung mit der PC-Software
Das Schloss verfügt über eine zusätzliche Mini USB-Schnittstelle an der Eingabeeinheit. Über diese Schnittstelle kann das
Schloss über eine als Zubehör erhältliche PC-Software programmiert werden.
Folgende Funktionen stehen bei Verwendung der zusätzlichen PC-Software zur Verfügung: a) Audit auslesen b) Schlosseinstellungen mit der Software programmieren
Weitere Details hierzu entnehmen Sie bitte der Bedienungsanleitung für die PC-Software.
12.2 Zusatzfunktionen über den Signal-Eingang
Belegung des Signal-Eingangs wird in der Installationsanleitung des Schlosses beschrieben. Die Aktivierung der Funktionen ist ausschließlich mit der optional erhältlichen PC-Software möglich. Das Bedienverhalten des Schlosses bei Anliegen der
verschiedenen Eingangssignale ist in 10.810.8 beschrieben.
12.3 Zusatzfunktionen über die Signal-Ausgänge
Das Schloss verfügt über 2 Signalausgänge: Details zur Belegung der Ausgänge finden Sie in der Installationsanleitung.
Folgende Ausgänge sind vorhanden:
a) Stiller Alarm. Details zur Programmierung siehe Kapitel 9.5, zur Bedienung siehe Kapitel 10.4,
b) Riegelschaltkontakt, keine zusätzliche Programmierung möglich.
13 Spannungsversorgung
Zur Spannungsversorgung des Schlosses befinden sich 2 Batterien Typ AAA in der Eingabeeinheit. Es wird dringend
wurde.
Stand 26.08.2016
Seite 21 von 48
Bedienungsanleitung 82132/3xxx CB 30
13.1 Unterspannungsanzeige
Erhält der Bediener
Batterien müssen umgehend gewechselt werden (siehe Kapitel13.2).
, so ist die Batteriekapazität erschöpft und die
Sobald die Unterspannungsanzeige erscheint, ist zwar weiterhin die Schlossöffnung möglich, allerdings sind nun bis zum
Batteriewechsel keinerlei Umprogrammierungen mehr möglich. Es erfolgt außerdem ein Auditeintrag. Sobald die Batterie nahezu komplett entleert ist, kann keine Öffnung mehr vorgenommen werden und jeder einzelne Tastendruck wird mit dem Unterspannungssignal quittiert.
13.2 Batterietausch
Wenden Sie keine Gewalt an und meiden Sie die Berührung elektronischer Komponenten! Sie könnten dadurch das
Schloss zerstören.
Zum Batterietausch muss der Drehgriff des Schlosses demontiert werden. Da der Drehgriff in 90 °-Schritten aufgesteckt werden kann, merken Sie sich bitte zunächst die Stellung des Drehgriffes für den anschließenden Zusammenbau (z.B. mittels eines
Klebestreifens auf der Eingabeeinheit, der die Position der Markierung auf dem Drehgriff wiedergibt). Drücken Sie nun den beiliegenden Inbusschlüssel wie in Abb. 6.1 dargestellt bis zum Anschlag in das Loch in der Seitenwand der Eingabeeinheit ein.
Nun den Drehgriff nach vorne aus der Eingabeeinheit herausziehen (siehe Abb. 6.2) und den Inbusschlüssel entfernen. Dann die Schraube in der Griffmulde herausschrauben (siehe Abb. 6.3). Anschließend kann das Oberteil der Eingabeeinheit wie in siehe Abb. 6.4 dargestellt verschoben und dann nach vorne abgenommen werden (siehe Abb. 6.5). Die 2 Batterien befinden sich auf dem Basisteil der Eingabeeinheit und können nun gemäß Abb. 6.6 ausgetauscht werden. Es dürfen nur Batterien des
Typs AAA verwendet werden. Es wird dringend empfohlen, hochwertige Markenbatterien zu verwenden und diese vorsorglich spätestens alle 24 Monate zu tauschen. Nach dem Wechseln der Batterie die Eingabeeinheit in umgekehrter Reihenfolge wie oben beschrieben wieder auf das Basisteil von vorne aufsetzen und zum Einrasten seitlich verschieben bis die rote LED erlischt. Anschließend die Schraube zur Sicherung des Oberteils montieren. Nun den Drehgriff wieder so orientiert aufstecken, wie er vor der Demontage war (hierzu dient die oben erwähnte Markierung). Bei korrekter Montage ist Drehgriff nun nicht mehr abziehbar. Markierung (so erfolgt) entfernen. Zum Abschluss muss noch die Abhebekontaktmeldung neutralisiert werden
(siehe Kapitel 9.6). Dies kann nur vom Master durchgeführt werden.
Batterietausch (gezeigtes Beispiel: Die Eingabeeinheit-Tastatur befindet sich rechts vom Drehgriff. Für andere Einbaulagen entsprechend anders vorgehen):
Abb. 6.1: Position Drehgriff (Markierung) merken. Inbusschlüssel in kleines Loch bis zum Anschlag eindrücken.
Abb. 6.2: Abziehen des Drehgriffes nach vorne, dabei Inbusschlüssel gedrückt halten
Abb. 6.3: Schraube lösen und entfernen.
Abb. 6.4: Eingabeeinheit Oberteil in
Pfeilrichtung bis zum Anschlag verschieben.
Abbildung 6: Batterietausch
Abb. 6.5: Eingabeeinheit Oberteil vorsichtig abnehmen.
Abb. 6.6: Batterien austauschen.
Montage in umgekehrter Reihenfolge.
Stand 26.08.2016
Seite 22 von 48
Bedienungsanleitung 82132/3XXX - Combi B 30
13.3 Permanentspannungsversorgung
Bei Bedarf kann das Schloss zusätzlich zur Batterieversorgung permanent mit Spannung versorgt werden. Hierfür stehen folgende Optionen zur Verfügung: a) Spannungsversorgung über eine Einbruchmeldeanlage und die Alarmbox (Art. Nr. 3001001550
) b) Spannungsversorgung über die Alarmbox (s.o.) bei Anbindung an eine Meldetechnik ohne
Spannungsversorgungsmöglichkeit über zusätzliches 12V-Netzteil an der Alarmbox (s.o.) Art. Nr. 3002501230 c) Bei Verwendung des Schlosses ohne jegliche Meldetechnik: 9V-Netzteil direkt am Schloss anschließbar,
Art. Nr. 3002501220
Auch bei Permanentspannungsversorgung müssen die Batterien in der Eingabeeinheit eingelegt werden, da sonst das
Schloss bei Spannungsausfall oder einem Defekt innerhalb der Permanentspannungsversorgung nicht mehr mittels
Codeeingabe geöffnet werden kann. Bei Ausfall der Permanentspannungsversorgung und erschöpfter Batteriekapazität
sollten dann schnellstmöglich überprüft werden.
14 Service
Bei Störungen oder in dieser Anleitung nicht beschriebenen Serviceaufgaben wird dringend empfohlen, auf einen fachkundigen
Servicetechniker oder den Tresorlieferanten zurückzugreifen.
Das Schloss verfügt in der Eingabeeinheit über einen Aufkleber mit Produktionsdaten, die z.B. im Fall einer telefonischen
Erstberatung oder in einem Servicefall bei einer ersten Fehlereingrenzung hilfreich sein könnten. Sollten Sie auf diese
Der Aufkleber befindet sich gut sichtbar auf der Innenseite des Oberteils der Eingabeeinheit:
Abbildung 7: Aufkleber in der Eingabeeinheit
Der Aufkleber enthält die folgenden Informationen:
Schloss-Typ
Artikelnummer der Eingabeeinheit
Seriennummer der Eingabeeinheit
Versionsnummer der Firmware und Herstelljahr
Abbildung 8: Informationen auf dem Aufkleber
Stand 26.08.2016
Seite 23 von 48
15 Notizen
Codes
Master
Benutzer 01
Benutzer 02
Benutzer 03
Benutzer 04
Benutzer 05
Benutzer 06
Benutzer 07
Benutzer 08
Benutzer 09
Benutzer 10
Benutzer 11
Benutzer 12
Benutzer 13
Benutzer 14
Benutzer 15
Benutzer 16
Benutzer 17
Benutzer 18
Benutzer 19
Benutzer 20
Benutzer 21
Benutzer 22
Benutzer 23
Benutzer 24
Benutzer 25
Benutzer 26
Benutzer 27
Benutzer 28
Benutzer 29
Benutzer 30
Kurier (Benutzer 95)
aktiviert gesperrt entsperrt gelöscht
Bedienungsanleitung 82132/3xxx CB 30
Funktion
ÖV/ÖBZ
Doppelcode
Stiller Alarm
Zusatzfunktionen
Fernsperre
Übersteuerung ÖV/ÖBZ
Übersteuerung Doppelcode
Unterlassungsalarm
___ / -__
Kaba Mauer GmbH
Frankenstrasse 8-12
D-42579 Heiligenhaus
Stand 26.08.2016
Seite 24 von 48
Combi B 30 with metal input unit
Operating Instructions
EN
Operating instructions 82132/3xxx CB 30
Table of contents
Version 2016-08-26
Page 26 of 48
Operating instructions 82132/3XXX - Combi B 30
List of tables
List of figures
Version 2016-08-26
Page 27 of 48
Operating instructions 82132/3xxx CB 30
16 Important notes
Before the start-up of the lock read these operating instructions carefully and observe the following notes:
The enclosed inspection key allows full access to the lock and its configurations even in case of code loss.
Thus, it is at the highest hierarchy level of the lock. Therefore, it must be stored in a safe place, but not in the secure storage unit.
For security reasons programming and battery replacement should always be performed and then tested with the secure storage unit open.
Every correct key stroke recognized by the lock is confirmed by an acoustic signal.
You have max. 10 sec. for each individual key stroke. If no key is pressed during these 10 seconds, the electronics shuts down automatically. Uncompleted operations must be restarted after that. The only exceptions to this are the code status query and the programming mode with 30 seconds response time until automatic shutdown.
Code inputs resp. all further functions (e.g. programming operations) can be cancelled until the last key stroke by pressing the key twice.
Do not use for your code personal or similar known data which are easy to find out.
If the set code(s) is(are) not available, the lock can be opened or reset using the enclosed inspection key.
The lock is designed for use in the temperature range from +10° C to +50° C and with humidity of 30% to 80% (noncondensing).
The lock must never be greased with or contact other lubricants or aggressive liquids, it must be cleaned only with a moist cloth only (no aggressive cleaning agents).
Never open the lock housing. Dismount the fitting only for battery replacement and perform it strictly according to the specifications of these operating instructions. Avoid touching electronic components. Otherwise, you endanger the functions of the lock and loose the right for the warranty claims.
During start-up the serial number of the input unit is saved in the audit memory of the lock. Replacement of the input unit is also registered by means of an entry in the audit memory of the lock.
For every description of operation or programming processes hereafter it is assumed that the lock and the input unit are in the basic state. Basic state means that the lock is closed (the bolt lock is extended) and the lock electronics is switched o ff.
If you are not sure, whether the lock is closed, check if the rotary knob can be turned counterclockwise. To ensure that the lock is not in a running programming process, you can press the key twice to cancel it.
Upon delivery the lock is set by Kaba Mauer GmbH to the factory code "1". For security reasons activate the master code with your individual code immediately in order to deactivate the factory code. The factory code is meant only for lock mounting, it is not suitable for further permanent use.
Furthermore, the lock has the option for partial or full start-up by the safe manufacturer or distributor:
For a partial start-up basic configurations are loaded to the lock without activation of the master code. So, the lock still opens with "1". All configurations performed previously using software are immediately valid only after
activation of the master code (start-up according to 8.2).
For full start-up the lock has already been provided with a master code and further settings if necessary.
In both cases the set basic configuration is communicated separately by the safe manufacturer or distributor. If a full start-up has been performed and, thus, a master code preset as delivery code, the safe manufacturer or distributor can save it additionally in the following hatched text box.
All pre-configured codes have to be changed by the end user immediately after start-up.
The master code set by the distributor resp. safe manufacturer (delivery code):
0 0 _ _ _ _ _ _ _
Note for the end user:
Change all delivery codes immediately!
If further codes have been pre-assigned, see separate information of the safe distributor resp. manufacturer.
_ _
Stamp of the safe manufacturer/distributor
Version 2016-08-26
Page 28 of 48
Operating instructions 82132/3XXX - Combi B 30
17 Glossary of abbreviations and terms
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
Code:
ID:
PIN:
Operator:
Master code:
User code:
Courier code:
Factory code:
TD:
CW:
Lockout period:
Dual code:
Silent alarm:
EMA:
Low battery:
AHK:
Audit:
Reset:
Inspection key:
Numerical sequence of 8 digits for identification of the operator consisting of ID and
PIN. fixed 2-digit operator number. freely selectable 6-digit combination (Notice, do not use personal data such as for example date of birth). the master, user and courier are operators of the lock
– each operator of the lock has an individual ID (00, 01..30; 95) assigned.
ID 00; the highest code of the code hierarchy, can open the lock, change its own code, it is required for almost all programming functions of the lock. Can also perform programming functions independently in the double-code mode.
ID 01 to 30, can open the lock and change its own code.
ID 95, can open the lock without waiting for an time delay which might be programmed and change its own code. has no ID, can open the lock during mounting at the factory. adjustable time which has to pass before the lock can be opened.
Confirmation window: adjustable time which starts after the time delay; The lock can be opened during the confirmation window.
After entering the code 3 times incorrectly the lockout period is activated, no inputs are
possible at the lock during the lockout period.
Two different valid codes are required to open the lock.
If the lock is connected to an external alarm system (intruder detection system) and this function is activated at the lock, a silent duress alarm can be triggered (not perceivable for the intruder).
Intruder detection system: external alarm system for evaluation / forwarding of the duress alarm or secured permanent power supply (not included in the scope of delivery). indicates that the batteries are low and must be replaced as soon as possible in order to ensure secure function of the lock.
Tamper switch: A contact in the input unit which detects whether the input unit has
been opened (e.g. for battery replacement).
All relevant events (opening, closing, programming etc.) are saved in the audit memory
(approx. 200 events) of the lock. If the memory is full, the oldest entry is overwritten automatically. The audit can be read out using software.
Reset of the lock to the delivery state, only the master code and audit remain unchanged.
The inspection key can open the lock any time mechanically independent of the electronics. Opening by means of the key does not have any TD or lockout period. The inspection key can also be used to assign a new master code and reset the complete lock. Reconfiguration of the lock can be implemented using the inspection key and software without knowing or changing the master code. Therefore, the inspection key is positioned higher in the code structure than the master code and must be stored in a safe place (not in a secure storage unit).
Version 2016-08-26
Page 29 of 48
oder
Table 29: Icons
Operating instructions 82132/3xxx CB 30
18 The icons used in the instructions
Icon Meaning
Warning
Important
Note
Icon for the 2-digit code ID (also refer to chapter 2)
Icon for individual number keys for the code input
Action performed
Action not performed
Rotate the actuating knob through 90° clockwise.
Rotate the actuating knob through 90° counterclockwise.
Short signal LED green
Continuous signal LED green
LED green off
Short signal LED red
Continuous signal LED red
LED red off
Buzzer signal
Version 2016-08-26
Page 30 of 48
Operating instructions 82132/3XXX - Combi B 30
19 Lock system: Input unit and lock
The entire lock system consists of a visible input unit and the lock installed in the secure storage unit.
All programmed codes and functions are saved only in the lock and, thus, in the secured area.
19.1 Operating elements of the input unit
Actuating knob Keypad
Keypad:
1 red and 1 green LED
Numeric keys
P key
Enter key
Figure 9: Input unit Figure 10: Mini-USB socket
Special interface, only in connection with original
Kaba Mauer CB30
Use PC cable!
19.2 Lock housing and interfaces
Connection to further components (e.g. EMA)
Power supply
Connection to the input unit
Figure 11: Lock housing Figure 12: Connections at the lock housing
Version 2016-08-26
Page 31 of 48
Operating instructions 82132/3xxx CB 30
20 Overview of authorizations
The authorizations of individual operators are as follows:
Operator ID
Code designation
Authorization
-
00
01..30
Inspection key
Master code
User codes
- Opening without TD/CW and without lockout period
- Assigning of a new master code
- Resetting the lock
- Changing the lock configurations using software without knowing the master code or changing it.
- Opening, if necessary, with silent alarm
- Changing of the own code
- Activating, blocking, releasing, deleting user and courier, with activated dual code as well
- Activating / deactivating dual code
- Programming / deleting TD/CW
- Neutralising the tamper switch
- Reading out audit
- Activating, deactivating silent alarm
- Access via PC software
- Opening, if necessary, with silent alarm
- Changing of the own code
95
-
Courier code
Factory code
- Opening without TD/CW, if necessary, with silent alarm
- Changing of the own code
- Opening
- Valid only until the real start-up of the lock,
NOT A REAL CODE, not suitable for permanent use
Table 30: Authorizations
21 Overview of the programming commands
Action Command Authorization
each Changing own code
Reading out audit
Activating + deactivating TD/CW
Activating user
Blocking + releasing user
Deleting user
Code status query
Activating + deactivating dual code
Activating + deactivating silent alarm
Acknowledging the tamper switch message
Resetting the lock
Reassignment of the master code
Table 31: Programming commands
P4
P5
P6
P7
P
P1
P2
P3
P8
P9
P0
P
Master
Key
Version 2016-08-26
Page 32 of 48
Operating instructions 82132/3XXX - Combi B 30
22 Overview of the possible signals
Event When
Pressing the key (e.g. code input)
Code valid (code-correct message)
Correct input
Error message (e.g. code invalid)
Recurring input (e.g. code confirmation) not matching
Cancelation (manual cancelation with or time-controlled cancelation if there is no input)
With every key stroke
After pressing
Enter
After pressing
Enter
Tamper switch has been activated
Lockout period
Dual code; input of the second code is expected
TD
CW
Undervoltage
Programming mode
Remote disable activated, no opening possible
3 x after pressing Enter
Permanently after pressing
Enter
Permanently after pressing
Enter
Permanently after pressing
Enter
Permanently after pressing
Enter
After pressing
Enter
Permanently after pressing
Enter
With every key stroke
Hardware error. Contact the Service.
After pressing
Enter
No connection to lock!
Check cable conncetion (plug at t he lock in „input unit“?); Top part of input unit not completely end positioned?
After fitting the top part of the input unit
Code status messages
Code active
Code active but blocked
After pressing
Enter
Code deleted or inactive
Table 32: Messages from the lock, terms see chapter 2, icons see chapter
1 x
2 x and 2 x
3 x
1 x and 1 x , then
1 x and 1 x
1 x , then 0.5 s break
1 x , then 2 s break
1 x , then 5 s break
1 x and 1 x , then 5 s break
10 x
1 x
1 x
and 3 x
Signal
and permanent
3 s and 3 s
1 x and 1 x
1 x , 1 x and 1 x
1 x and 1 x
Version 2016-08-26
Page 33 of 48
Operating instructions 82132/3xxx CB 30
23 Start-up of the lock
The lock installation as well as cabling and the first battery installation are described in the installation manual.
As long as the lock system has not been put into operation, it can be opened using the factory code.
The factory code is intended for lock mounting at the factory and not for further permanent use.
code invalid.
If the start-up or partial start-up has already been performed by the safe manufacturer or distributor, the corresponding information is specified in its manuals/notes. Furthermore, the safe manufacturer or distributor can document the set
set by the distributor resp. safe manufacturer".
23.1 Opening with factory code
Description
1. Press and 2x 2x 3x 3x
2.
Turn the actuating knob within 4 seconds through 90°
Then open the storage unit.
Table 33: Opening with factory code
As long as the factory code is used for opening (master is not activated yet), there is no lockout period for incorrect code
inputs according to chapter 10.5 and no tamper switch signal message according to either.
23.2 Activating master
Now activate the master with the storage unit open (to have every time access to the storage unit and the lock).
Description
1. Press and
Version 2016-08-26
Page 34 of 48
2x 3x 3x
2. Enter the new master code
(00 = ID, X = freely selected 6-digit combination [0..9])
and
2x 3x 3x
3. Confirm the new master code with and 2x 2x 3x 3x
Table 34: Activating master
If the Incorrect code signal is output, the procedure must be repeated since both codes do not match or the ID (here
00) has been entered incorrectly.
Changing of the master code can be canceled any time by pressing twice. Alternatively, the process can be canceled if no input is performed within 30 seconds.
24 Programming functions for the master
All programming functions described here require the master code for authorisation.
For security reasons, programming and testing of programming should always be performed with the secure storage unit open (to have every time access to the storage unit and the lock). Programming can be performed any time individually and without waiting times (exception - lockout periods), even if the dual code and/or TD/CW are activated. All programming processes can be canceled by pressing twice. Alternatively, the input can be canceled if no input is performed within 30 seconds.
Operating instructions 82132/3XXX - Combi B 30
24.1 Changing master code (P)
After modification of the master code the previous master code is no longer valid. The function of the new master code must be
checked by opening the lock with the secure storage unit open (see chapter 10.1)!
Description
1. Press
and enter the current master code
(00 = ID, X = previously programmed 6-digit combination)
and
2x 3x 3x
and
2. Enter the new master code
(00 = ID, Y = new 6-digit combination)
2x 3x 3x
3. Confirm the new master code with and 2x 2x 3x 3x
Table 35: Changing master code
The entire procedure has to be repeated in case of the following errors:
If Incorrect code signal is displayed according to 1. after the input of the current code, the code has been entered incorrectly.
If the Incorrect code signal is displayed after the second attempt to enter the new code as shown in 3., then the two codes entered in 2. resp. 3 do not match.
24.2 Programming functions for further codes (P3-P6)
This section describes the basic programming procedures for further codes (user or courier codes). This includes activation,
chapter describes the code status query used by the master code to request the status of individual codes directly from the lock.
For correct use of the lock the master code must be activated (see chapter 8.2).
24.2.1 Activating user codes or courier codes (P3)
Code can be used only after it has been activated. When activating a new operator, it is useful if the new code (starting from item 3 of the following description) is entered directly by the respective operator on site. If the new code is not entered by the operator directly but is specified by the master, it must be replaced by the real personal code in the course of code changing as
soon as possible (see chapter 10.7).
Description
1. Press
and enter the valid master code
(00 = ID, X = valid 6-digit combination for the master)
and
2x 3x 3x
2. Press and 2x 3x 3x
3. Enter the new code
and
(ID = 01 to 30 for user resp. 95 for courier, X = freely selectable 6-digit combination [0..9])
2x 3x 3x
4. Confirm the new code with and 2x 2x 3x 3x
Table 36: Activating code
After the activation the new saved code is valid and can be used. The new code has to be tested by opening the lock (see
If both entered codes do not match, the incorrect code signal is output after the second code input. If the Incorrect code signal is displayed after the first code input, the code is already active or not available.
Version 2016-08-26
Page 35 of 48
Operating instructions 82132/3xxx CB 30
24.2.2 Blocking the user codes or courier codes (P4)
blocking the code remains unchanged in the lock and can be used again after releasing.
Description
1. Press
and enter the valid master code
(00 = ID, X = valid 6-digit combination for the master)
and
2x 3x 3x
2. Press and 2x 3x 3x
3. Enter the ID to be blocked
(ID = 01 to 30 for user resp. 95 for courier)
and
2x 2x 3x 3x
Table 37: Blocking the code
If the Incorrect code signal is displayed after step 3, then either the ID has not been activated or it is not available.
If only the red LED is missing during the acknowledgment signal, the code has not been blocked but released, because it had been blocked before that. Perform the entire procedure again to block the code again.
Blocking of the master code is not possible.
24.2.3 Releasing the user codes or courier codes (P4)
After releasing of the code blocked previously according to 9.2.2, it can be used again.
Description
1. Press
and enter the valid master code
(00 = ID, X = valid 6-digit combination for the master)
and
2x 3x 3x
2. Press and 2x 3x 3x
3. Enter the ID to be released
(ID = 01 to 30 for user resp. 95 for courier)
and
2x 2x 3x 3x
Table 38: Releasing code
If the Incorrect code signal is displayed after step 3, then either the ID has not been activated or it is not available.
If the red LED is displayed additionally to the normal acknowledgment signal, the code has not been released but blocked, because it had been released before that. Perform the entire procedure again to release the code again.
24.2.4 Deleting the user codes or courier codes (P5)
(see chapter 9.2.1). Blocked codes can be deleted without previous releasing.
Description
1. Press
and enter the valid master code
(00 = ID, X = valid 6-digit combination for the master)
and
2x 3x 3x
2. Press and 2x 3x 3x
3. Enter the ID to be deleted
(ID = 01 to 30 for user resp. 95 for courier)
and
2x 2x 3x 3x
Table 39: Deleting code
If the Incorrect code signal is displayed after step 3, then either the ID has not been activated or it is not available.
Deletion of the master code is not possible. However, the master code can be reassigned using the key (see chapter
Version 2016-08-26
Page 36 of 48
Operating instructions 82132/3XXX - Combi B 30
24.2.5 Code status query (P6)
The status of any code (active, blocked or inactive resp. deleted) can be requested in this query program. Neither the codes nor their statuses are changed by this operation. The statuses of any number of IDs can be requested successively. Different code
statuses are given in Tabelle 13.
Description
1. Press
and enter the valid master code
(00 = ID, X = valid 6-digit combination for the master)
and
2x 3x 3x
2x 2x 3x 3x 2. Press and
3.
Enter all the ID(s) to be requested successively and correspondingly
One code status message is generated for each ID according to
4.
Quit the query mode by pressing .
Alternatively, wait for 30 seconds
Table 40: Requesting code status
Code status message
3x 3x
3x 3x
(active) 1x 1x
(active but blocked) 1x 1x 1x
(deleted/inactive) 1x 1x
Table 41: Code status messages
24.3 Programming time delay and confirmation window (P2)
Time delay (TD) is the time period which has to elapse before the lock can be opened. The confirmation window (CW) denotes the time window during which the lock can be opened as soon as the TD has elapsed. This program is used to set or delete the
TD (01 to 99 minutes) and the CW (01 to 19 minutes). The set times apply to all users and for the master but not for the courier.
24.3.1 Activating time delay and confirmation window (P2)
To program time delay (TD) and confirmation window (CW) proceed as follows:
Description
1. Press
and enter the valid master code
(00 = ID, X = valid 6-digit combination for the master)
and
2x 3x 3x
2. Press and 2x 3x 3x
3. Enter the time delay
and the confirmation window
(XX = 01 to 99, YY= 01 to 19, specifications in minutes respectively)
and
2x 2x 3x 3x
Table 42: Programming time delay and confirmation window
If the Incorrect code signal is displayed after step 3, the specified times are outside of the maximum permitted range.
The Incorrect code signal is also displayed if 00 is specified either only for the TD or for the CW. Both inputs are not permitted.
24.3.2 Deactivating time delay and confirmation window (P2)
for the 2-digit TD as well as for the 2-digit CW respectively. After that all operators can open the lock without delay.
Version 2016-08-26
Page 37 of 48
Operating instructions 82132/3xxx CB 30
Description
2x 3x 3x 1. Press
and enter the valid master code
(00 = ID, X = valid 6-digit combination for the master)
and
2 Press and 2x 3x 3x
2x 2x 3x 3x 3. Enter and
Table 43: Deleting time delay and confirmation window
24.4 Programming the dual code (P7)
The dual code function allows to set the lock in such a way that two optional but different codes (different IDs) are required to open the lock. The dual code includes all operators (master, user and courier). This programming command is used to activate or deactivate the dual code.
24.4.1 Activating the dual code (P7)
In order to activate the dual code proceed as follows:
Description
1. Press
and enter the valid master code
(00 = ID, X = valid 6-digit combination for the master)
and
2x 3x 3x
2. Press and 2x 2x 3x 3x
Table 44: Activating dual code
The lock can be opened only as described in 10.3.
To activate the dual code, at least two operators with valid codes must be created. Otherwise, an error message is displayed during activation of the dual code.
The dual code must be deactivated in order to be able to activate it.
If the red LED is displayed additionally to the normal acknowledgment signal, the dual code has been activated previously and is deactivated now. To activate it again, repeat the entire procedure.
24.4.2 Deactivating dual code (P7)
In order to deactivate the dual code proceed as follows:
Description
1. Press
and enter the valid master code
(00 = ID, X = valid 6-digit combination for the master)
and
2x 3x 3x
2. Press and 2x 2x 3x 3x
Table 45: Deactivating dual code
The dual code must be activated in order to be able to deactivate it.
If the red LED is missing during the acknowledgment signal, the dual code has been deactivated previously and is activated now. To deactivate it again, repeat the entire procedure.
Version 2016-08-26
Page 38 of 48
Operating instructions 82132/3XXX - Combi B 30
24.5 Programming silent alarm (P8)
A silent alarm is triggered by a special code input. The message in question is an alarm message which initiates the lock using an alarm output, the lock can still be opened during this. However, to forward the silent alarm, the alarm output must be connected to the intruder detection system (not included in the scope of delivery) (for further details refer to the installation manual or consult an installer of intruder detection systems). This programming command is used to activate or deactivate the
silent alarm. To open the lock using the alarm code proceed as described in 10.4.
If the silent alarm is deactivated, the alarm codes are acknowledged as incorrect codes and the lock does not open.
24.5.1 Activating the silent alarm (P8)
To activate the silent alarm proceed as follows: After that the silent alarm is activated and the alarm codes can be used.
Description
1. Press
and enter the valid master code
(00 = ID, X = valid 6-digit combination for the master)
and
2x 3x 3x
2. Press and 2x 3x 3x
Table 46: Activating silent alarm
The silent alarm must be deactivated in order to be able to activate it.
If the red LED is displayed additionally to the normal acknowledgment signal, the silent alarm has been activated previously and is deactivated now. To activate it again, repeat the entire procedure.
24.5.2 Deactivating silent alarm (P8)
To deactivate the silent alarm proceed as follows: After that the silent alarm is deactivated, the alarm codes are acknowledged as incorrect codes and the lock can no longer be opened with an alarm code.
Description
1. Press
and enter the valid master code
(00 = ID, X = valid 6-digit combination for the master)
and
2x 3x 3x
2. Press and 2x 2x 3x 3x
Table 47: Deactivating silent alarm
The silent alarm must be activated in order to be able to deactivate it.
If the red LED is missing during the acknowledgment signal, the silent alarm has been deactivated previously and is activated now. To deactivate it again, repeat the entire procedure.
24.6 Acknowledging tamper switch message (P9)
The lock is equipped with a tamper switch (AHK), which is tripped when opening the input unit (e.g. to replace the battery or after a manipulation); after that it is displayed with the manipulation signal for each opening/operation until the acknowledgment
(3x und 3x im Wechsel + 6x ).
This programming command acknowledges the tamper switch message. This procedure is saved in the event memory/audit of the lock like all other procedures.
If the signal mentioned above is displayed even if no battery replacement has been performed, the input unit might have been manipulated, for example to spy out the code. So, before you acknowledge this message, make sure that no manipulation has been performed at the input unit. If you are not sure, whether there has been a manipulation or not, consult an authorized service!
To acknowledge the tamper switch message and, thus, switch off the manipulation indication, proceed as follows:
Version 2016-08-26
Page 39 of 48
Operating instructions 82132/3xxx CB 30
Description
1. Press
and enter the valid master code
(00 = ID, X = valid 6-digit combination for the master)
and
2x 3x 3x
2. Press and 2x 3x 3x
Table 48: Acknowledging the tamper switch message
25 Lock functions for all users
twice. Alternatively, the input can be canceled if no input is performed within 10 seconds.
After three incorrect code inputs the lock switches to lockout period. For details on the lockout period refer to chapter
If the
must be replaced as soon as possible. For further details refer to chapter 13.
If the tamper switch signal (3x
opened. To find out more read chapter 9.6.
is displayed after the code entry, the input unit has been
The lock has a function which hinders spying out of codes by means of user observation during code input: During all opening procedures the operator can add as many further digits as necessary before completing the input by pressing
. All inputs starting from the 9th position will be ignored. Notice: This function supports only the code input for opening and is not available for the programming procedures.
Opening with activated additional functions: The lock offers an option to execute further additional functions triggered by
external signals. For further details refer to chapter 10.8.
25.1 Opening the lock without programmed TD/CW
Description
1. Enter a valid opening code
and
(ID = 00 to 30 resp. 95, X = programmed 6-digit combination for the corresp. ID number)
2x 2x 3x 3x
2. Turn the actuating knob within 4 seconds through 90° clockwise to the stop
.
Table 49: Opening with master or user code
If the Incorrect code signal is output after the code input, the entry must be repeated completely. After 3 incorrect inputs
the lock switches to the lockout period (see chapter 10.5)
25.2 Opening the lock with programmed TD/CW
Description
1.
2.
3.
Enter a valid opening code and
(ID = 00 to 30 or 95, X = programmed 6-digit combination for the corresp. ID number)
If you have entered a courier code here, proceed directly with step 4.
If you have not entered any courier code (ID 95), the signal for the running time delay is displayed now
(1x ; 5 s break). Wait until it is completely over.
The confirmation window starts after the time delay (1x
Now enter a valid opening code and again
(ID = 00 to 30, X = programmed 6-digit combination for the corresp. ID number)
2x 2x 3x 3x
2x 2x 3x 3x
4. Turn the actuating knob within 4 seconds through 90° clockwise to the stop
.
Table 50: Opening with programmed TD/CW
Version 2016-08-26
Page 40 of 48
Operating instructions 82132/3XXX - Combi B 30
The running time delay can be canceled any time by pressing twice.
If the Incorrect code signal is output after the code input, the entry must be repeated completely. After 3 incorrect inputs
the lock switches to the lockout period (see chapter 10.5).
Courier code:
After entering the courier code (ID 95) the lock can be opened immediately if the programmed TD (time delay) is avoided in a certain manner (steps 2 and 3 are omitted).
Dual code mode:
the input of an individual code.
Avoiding the TD/CW with the courier code in the dual code mode:
To enable this, the courier code must be the first entered code in the dual code mode. Then the second code (not the courier code) can be entered and after that the lock can be opened.
Inspection key:
The TD can be avoided if the inspection key is used, but it cannot be deleted (see chapter 11.1).
25.3 Opening with dual code
Description
1. Enter the first valid opening code
and
(ID = 00 to 30 or 95, X = programmed 6-digit combination for the corresp. ID number)
2x 2x 3x 3x
2. Now the signal for the input of the second is displayed (1x ; 2 s break)
3. Enter another valid opening code
and
(ID = 00 to 30 or 95, however, other than in step 1, Y = programmed 6-digit combination for the corr. ID number)
2x 2x 3x 3x
4. Turn the actuating knob within 4 seconds through 90° clockwise to the stop
.
Table 51: Opening with dual code
The operator IDs of both codes must not match. The order of the code input is irrelevant, unless it is necessary to open
entry must be repeated completely. If the Incorrect code signal is displayed after the second code input, the second entered code is incorrect or identical to the first input (identical IDs). In both cases the input must be repeated
here, whether the faulty input was in the first or the second code. Even if the faulty inputs occur in the first or second code alternately, after 3 incorrect inputs the lock switches to the lockout period.
25.4 Opening with silent alarm
If there is a threatening situation, the lock can be opened with simultaneous generation of a silent alarm, provided the silent
scope of delivery). A special alarm code derived from a valid code must be entered for this purpose (if the dual code is activated, one of the codes is sufficient). If an alarm code is entered, the lock opens externally as usual but a silent alarm is initiated additionally without further visible/audible feedback.
The alarm code consists of a valid code, the last position/digit of this code is increased or decreased by one digit (+1 or -1; see examples). If the last code digit is 0 or 9, then the digit next to the last in the alarm code is not changed (see example 2). If an time delay has been programmed, this time has to elapse still in spite of the alarm code input.
If the silent alarm is deactivated, the alarm codes are acknowledged as incorrect codes and the lock cannot be opened resp. the TD is not activated.
Examples:
Normal code 00123459 Normal code 00123456
Alarm code -1
Alarm code +1
00123458
00123450
Table 52: Alarm code examples
Alarm code -1 00123455
Alarm code +1 00123457
Version 2016-08-26
Page 41 of 48
Operating instructions 82132/3xxx CB 30
Opening process:
Description
1.
Enter a modified valid opening code as an alarm code
and
(ID = 00 to 30 or 95, X = the first 5 positions of the programmed 6-digit combination for the corr. ID number,
Y = increased by 1 or decreased at the 6th position of the combination mentioned above)
2x 2x 3x 3x
2. Turn the actuating knob within 4 seconds through 90° clockwise to the stop
.
Table 53: Opening with alarm code
If the Incorrect code signal is output after the code input, the entry must be repeated completely. After 3 incorrect inputs
the lock switches to lockout period in this case as well (see chapter 10.5)
Dual code:
With the activated dual code it is sufficient to enter both codes as alarm codes in order to activate the silent alarm.
However, the alarm is activated only if both codes required for opening have been entered completely.
25.5 Lockout period (3 or more incorrect code inputs)
After 3 incorrect inputs the lock switches to a 1-minute lockout period. For each further incorrect code input the lockout period is extended to 2, 4, 8 and finally to 16 minutes. During the entire lockout period no code input is possible. The lockout period can
has elapsed, the lock can be opened as described in chapter 10.1 to 10.4.
25.6 Closing the lock
Turn the actuating knob counterclockwise through 90° to the stop . Code input is not required.
If there is a boltwork available (usually recognized due to an additional rotary handle on the secure storage unit), it has to be locked, first, after the door has been closed. Only after that the lock can be closed.
Secure closing of the lock has to be tested by trying to rotate the knob at the input unit. The knob must not be turned through more than approx. 45°.
25.7 Changing codes (P)
Everyone is authorised to change his/her own code any time. The master is not authorised to change the user or courier code.
But he/she can activate, block, release and delete codes.
After changing the previous code is no longer valid and the new code must be used. The function of the new code must be
tested by opening the lock with the secure storage unit open (see chapter 10.1)!
Description
and
1. Press
and enter the code to be changed
(ID [00 to 30 or 95], X = programmed 6-digit combination for the corr. ID number)
2. Enter the new code
and
(ID the same as in 2, Y = new 6-digit combination for this ID number)
2x 3x 3x
2x 3x 3x
3. Confirm the new code with and 2x 2x 3x 3x
Table 54: Changing code
The entire procedure has to be repeated in case of the following errors:
If the Incorrect code signal is displayed according to 1. after the entry of the code to be changed, the code has been entered incorrectly or not assigned and, thus, cannot be changed.
If the Incorrect code signal is displayed after the first new code input as described in 2., the ID does not match the ID in step 1. The ID must always be kept, even in case of code modification.
If the Incorrect code signal is displayed after the second attempt to enter the new code as shown in 3., then the two codes entered in 2. resp. 3 do not match.
Version 2016-08-26
Page 42 of 48
Operating instructions 82132/3XXX - Combi B 30
25.8 Opening with activated additional functions
The lock has special additional functions (only one of them respectively) which can be set only using the optional PC software.
If one of these functions is activated, the lock reacts differently than described above: e) Remote disable:
If the "Remote disable" function is activated and there is an active corresponding input signal, each key is acknowledged with 1x Thus, no input is possible. f) TD/CW override:
If any time delay times and the associated confirmation windows have been programmed, they can be overridden here. g) Dual code override:
This function turns the programmed dual code into a simple code. The second code which is required usually is omitted here. h) Omission alarm: If this function is activated at the lock, an separate input signal must be initiated max. 60 seconds before the code input (e.g. by means of a hidden button); otherwise, the lock generates the silent alarm, unlike
described in 10.4 in spite of correct code input.
26 Key functions
26.1 Key opening
Opening of the lock using the inspection key is intended only for the emergency situation and not for permanent use.
Do not apply force when opening the lock using the key! You could destroy the lock.
For opening by means of the key the rotary handle must be dismounted. Since the rotary handle can be inserted in steps of 90 °
, first, always note the position of the rotary handle for the assembly later (e.g. using an adhesive tape on the input unit to mark the position of the mark on the rotary handle). Insert the enclosed Allen wrench up to the stop into the small hole on the lateral wall of the input unit (see fig. 5.1) Pull out the rotary handle to the front from the input unit (see fig. 5.2) and remove the Allen wrench. Then pull out the square shaft out of the lock (see fig. 5.3). Now the key can be inserted into the lock as shown in fig.
5.4 (lock housing horizontally with the bolt on the left). If the installation position of the lock is not known, determine the correct direction of the key by testing in 90° steps. Alternatively, you can ask the service technician or the cabinet manufacturer. After correct insertion for lock opening turn the key through approx. 150° to the right to the stop (see fig. 5.5). The lock is open now.
After opening by means of the key mount the input unit again in the reverse order as described above and place the key to a safe place, however, do not keep it in the secure storage unit.
the Open position of the lock.
Fig. 5.1: Notice: Note the position of the rotary handle (marking).
Insert the Allen wrench up to a stop into a small hole on the bottom side.
Fig. 5.2: Remove the rotary handle to the front, while keeping the Allen wrench pressed.
Fig. 5.3: Removing the Allen wrench and square shaft.
Fig. 5.4: Inserting the key.
Figure 13: Opening with the key
Fig. 5.5: Turning the key clockwise to the stop.
Version 2016-08-26
Page 43 of 48
Operating instructions 82132/3xxx CB 30
26.2 Closing using the key
Turn the key to the stop counterclockwise through approx. 150°, remove it and secure against unauthorised access (not inside the secure storage unit). Then insert the square shaft with the end of the bore forwards into the lock (see fig. x) and attach the
this purpose). In case of correct mounting the rotary knob cannot be removed now. The marking can be removed now.
26.3 Changing master code using the key (P)
This programming command is used to change the master code without knowing the master code. This may be helpful if the master code is no longer available, and the other settings of the lock should not be changed.
This programming command can only be executed while the lock is opened using the key. The function of the new master code must be tested by opening the lock with the safe open!
Description
1. Open the lock using the key (see chapter 11.1)
2. Press and
2x 3x 3x
3. Enter the new master code
(00 = ID, X = freely selected, 6-digit combination 0..9)
and
2x 3x 3x
2x 2x 3x 3x 4. Confirm the new master code and enter
5.
Table 55: Changing master code using the key
If both entered codes do not match, the Incorrect code signal is output after the second code input.
If the Incorrect code signal is displayed after the first code input, the ID is incorrect. During master code modification the
ID must always be "00"!
The procedure can be canceled without change any time by pressing twice. Alternatively, the modification is
26.4 Resetting the lock (P0)
This programming command is used to reset the lock. This means that this procedure deletes all settings of the lock (user code, courier code, dual code, silent alarm, time delay and confirmation window), only the master code and the audit remain unchanged.
This programming command can only be executed while the lock is opened using the key.
Version 2016-08-26
Page 44 of 48
Operating instructions 82132/3XXX - Combi B 30
Description
1. Open the lock using the key (see chapter 11.1)
2. Press and
3. Press and
4. Close the lock again by means of the key (11.2) and mount the rotary handle (11.1)
Table 56: Resetting the lock
This procedure can be canceled any time by pressing twice. Alternatively, the modification is canceled if there is no
input for 30 seconds or if the lock is locked using the key before step 3 (see chapter 11.2).
26.5 Reconfiguration of the lock after opening by means of the key using software
For further details on the procedure refer to the operating instructions for the PC software.
the lock is possible, namely without knowing or changing the master code. Only an audit entry is performed.
27 Further special functions
27.1 Connection to the PC software
The lock has an additional mini-USB interface on the input unit. The lock can be programmed via this interface using the PC software available as an accessory.
The following functions are available when using the additional PC software: c) Reading out audit d) Programming the lock settings using software
For further details on this refer to the operating instructions of the PC software.
27.2 Additional functions via the signal input
assignment of the signal inputs is described in the installation manual of the lock. The functions can only be activated with the
27.3 Additional functions via the signal outputs
The lock has 2 signal outputs: Details on assignment of the outputs are given in the installation manual. The following outputs are available:
d) Microswitch for bolt monitoring, no additional programming possible.
28 Power supply
Two batteries of type AAA are available in the input unit for power supply of the lock. It is highly recommended to replace them
every 2 years (see chapter 0), irrespectively of how often the lock has been used.
2x 3x 3x
2x 2x 3x 3x
Version 2016-08-26
Page 45 of 48
Operating instructions 82132/3xxx CB 30
28.1 Low battery
ry
must be replaced promptly (see chapter13.2).
As soon as the low battery is displayed, the lock can still be opened, but no reprogramming is possible until after the battery replacement. Furthermore, an audit entry is performed. As soon as the battery is almost completely exhausted, no opening can be performed and every key stroke is acknowledged with an undervoltage signal.
28.2 Battery replacement
Do not apply force and avoid touching electronic components! You could destroy the lock.
For battery replacement the rotary handle of the lock must be dismounted. Since the rotary handle can be inserted in steps of
90 ° , first, always note the position of the rotary handle for the assembly later (e.g. using an adhesive tape on the input unit to mark the position of the mark on the rotary handle). Insert the enclosed Allen wrench up to the stop into the hole on the lateral wall of the input unit as shown in Fig. 6.1. Pull out the rotary handle to the front from the input unit (see fig. 6.2) and remove the
Allen wrench. Then unscrew the screw in the handle recess (see fig. 6.3). After that the top part of the input unit can be moved as shown in fig. 6.4 and then it can be removed to the front (see fig. 6.5). The 2 batteries are located on the base part of the input unit and can be replaced now as shown in fig. 6.6. Only batteries of type AAA can be used. It is highly recommended to use high-quality brand batteries and replace them as a precaution every 24 months at the latest. After the battery replacement mount the input unit on the base part from the front in the order reverse to the one described above and move it laterally until it engages and the red LED turns off. Then attach the screw to secure the top part. Now attach the rotary handle in the position in which it has been mounted before dismounting (to do so, use the marking mentioned above). If the mounting is correct, the rotary handle can no longer be removed. Remove the marking (in this way).
Battery replacement (example above: the input unit keyboard is located to the right of the rotary handle. For other mounting positions proceed correspondingly):
Fig. 6.1: Notice: Note the position of the rotary handle (marking).
Insert the Allen wrench into the small hole on the bottom side and press it in to the stop.
Fig. 6.2: Remove the rotary handle to the front, while keeping the Allen wrench pressed. Fig. 6.3: Loosen and remove the screw.
Fig. 6.4: Move the top part of the input unit in the direction of the arrow to the stop.
Figure 14: Battery replacement
Fig. 6.5: Remove the top part of the input unit carefully.
Fig. 6.6: Replacing the batteries.
Mounting in the reverse order.
Version 2016-08-26
Page 46 of 48
Operating instructions 82132/3XXX - Combi B 30
28.3 Permanent power supply
If necessary, along with the battery power supply the lock can also be supplied with voltage permanently. The following options are available for this purpose: a) Power supply via the intruder detection system and the alarm box (art. no. 3001001550
) b) Power supply via the alarm box (see above) for connection to the signalling equipment without power supply option via the additional 12V power supply unit at the alarm box (see above) art. no. 3002501230 c) If the lock is used without any signalling equipment: 9V power supply unit can be connected directly at the lock, art. no. 3002501220
Even with the permanent power supply the batteries must still be inserted into the input unit because otherwise the lock cannot be opened by means of the code entry in case of power failure or a fault of the permanent power supply. The low
batteries and the permanent power supply should be checked as soon as possible in this case.
29 Service
In case of faults or service tasks described in this manual it is highly recommended to consult a professional service technician or the safe manufacturer.
The lock has a label with the production data on the input unit, these data that might be helpful, for example in case of the first telephone consultation or in case of service for the initial fault localization. If you would like to access these data, open the input
unit similarly as for the battery replacement described in chapter 13.2.
The label is clearly visible on the inside of the top part of the input unit:
Figure 15: Label with the production data in the input unit
The label contains the following information:
Lock type
Article number of the input unit
Serial number of the input unit
Version number of the firmware and year of manufacture
Figure 16: Information on the label
Version 2016-08-26
Page 47 of 48
30 Notes
Codes
User 17
User 18
User 19
User 20
User 21
User 22
User 23
User 24
User 25
User 26
User 27
User 28
User 29
User 30
Courier (User 95)
Master
User 01
User 02
User 03
User 04
User 05
User 06
User 07
User 08
User 09
User 10
User 11
User 12
User 13
User 14
User 15
User 16
Activated Blocked Released Deleted
Operating instructions 82132/3xxx CB 30
Function
OD/OST
Double code
Silent alarm
Additional functions
Remote disable
Override OD/OST
Override Double code
Omission alarm
___ / -__
Kaba Mauer GmbH
Frankenstrasse 8-12
D-42579 Heiligenhaus, Germany
Version 2016-08-26
Page 48 of 48
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 4 Wichtige Hinweise
- 5 Abkürzungs- und Begriffsverzeichnis
- 6 In der Anleitung verwendete Symbole
- 7 Schloss-System: Eingabeeinheit und Schloss
- 7 Bedienelemente der Eingabeeinheit
- 7 Schlossgehäuse und Schnittstellen
- 8 Berechtigungsübersicht
- 8 Übersicht über die Programmierbefehle
- 9 Übersicht der möglichen Signale
- 10 Inbetriebnahme des Schlosses
- 10 Öffnen mit Monteurcode
- 10 Master aktivieren
- 10 Programmierfunktionen für den Master
- 11 Mastercode ändern (P)
- 11 Funktionen für weitere Codes programmieren (P3-P6)
- 11 Benutzercodes oder Kuriercodes aktivieren (P3)
- 12 Benutzercodes oder Kuriercodes sperren (P4)
- 12 Benutzercodes oder Kuriercodes entsperren (P4)
- 12 Benutzercodes oder Kuriercodes löschen (P5)
- 13 Codestatus-Abfrage (P6)
- 13 Öffnungsverzögerung und Öffnungsbereitschaftszeit programmieren (P2)
- 13 Öffnungsverzögerung und Öffnungsbereitschaftszeit aktivieren (P2)
- 13 Öffnungsverzögerung und Öffnungsbereitschaftszeit deaktivieren (P2)
- 14 Doppelcode programmieren (P7)
- 14 Doppelcode aktivieren (P7)
- 14 Doppelcode deaktivieren (P7)
- 15 Stillen Alarm programmieren (P8)
- 15 Stillen Alarm aktivieren (P8)
- 15 Stillen Alarm deaktivieren (P8)
- 15 Abhebekontakt-Meldung quittieren (P9)
- 16 Schlossfunktionen für alle Benutzer
- 16 Schloss öffnen ohne programmierte ÖV/ÖBZ
- 16 Schloss öffnen bei programmierter ÖV/ÖBZ
- 17 Öffnen mit Doppelcode
- 17 Öffnen mit Stillem Alarm
- 18 Sperrzeit (3 oder mehr fehlerhafte Codeeingaben)
- 18 Schloss schließen
- 18 Codes ändern (P)
- 19 Öffnung bei aktivierten Zusatzfunktionen
- 19 Schlüsselfunktionen
- 19 Schlüsselöffnung
- 20 Verschließen mit dem Schlüssel
- 28 Important notes
- 29 Glossary of abbreviations and terms
- 30 The icons used in the instructions
- 31 Lock system: Input unit and lock
- 31 Operating elements of the input unit
- 31 Lock housing and interfaces
- 32 Overview of authorizations
- 32 Overview of the programming commands
- 33 Overview of the possible signals
- 34 Start-up of the lock
- 34 Opening with factory code
- 34 Activating master
- 34 Programming functions for the master
- 35 Changing master code (P)
- 35 Programming functions for further codes (P3-P6)
- 35 Activating user codes or courier codes (P3)
- 36 Blocking the user codes or courier codes (P4)
- 36 Releasing the user codes or courier codes (P4)
- 36 Deleting the user codes or courier codes (P5)
- 37 Code status query (P6)
- 37 Programming time delay and confirmation window (P2)
- 37 Activating time delay and confirmation window (P2)
- 37 Deactivating time delay and confirmation window (P2)
- 38 Programming the dual code (P7)
- 38 Activating the dual code (P7)
- 38 Deactivating dual code (P7)
- 39 Programming silent alarm (P8)
- 39 Activating the silent alarm (P8)
- 39 Deactivating silent alarm (P8)
- 39 Acknowledging tamper switch message (P9)
- 40 Lock functions for all users
- 40 Opening the lock without programmed TD/CW
- 40 Opening the lock with programmed TD/CW
- 41 Opening with dual code
- 41 Opening with silent alarm
- 42 Lockout period (3 or more incorrect code inputs)
- 42 Closing the lock
- 42 Changing codes (P)
- 43 Opening with activated additional functions
- 43 Key functions
- 43 Key opening
- 44 Closing using the key