- Computers & electronics
- Audio & home theatre
- Portable speakers
- Cambridge Audio
- 5055300406026
- Data Sheet
advertisement
Minx Satellites Specifications
Min11
I
BMR (Balanced Mode Radiator) full range driver combining bending wave technology for higher frequencies, with pistonic driver movement for lower frequencies
I Incredibly wide dispersion from the BMR driver virtually eliminates any ‘sweet spot’ problem
I BMR technology offers wide frequency response from a single driver, allowing for optimum integration with a subwoofer
Min21
I
Acoustically damped thermo polymer cabinet construction ensuring a rigid speaker cabinet to disperse colouration
I Scratch resistant high gloss lacquer available in black or white finishes
I Optional table top or floor stands available
Min11 specifications
Sensitivity (SPL)
Frequency response
Impedance
Recommended Amp Power
Drivers
Dimensions (H x W x D)
Weight
Finishes
Min21 specifications
85dB (2.83 Vrms input)
120Hz-20kHz
8 Ohms compatible
25-200W*
1 x 2.25" BMR
Sensitivity (SPL)
Frequency response
Impedance
Recommended Amp Power
Drivers
78 x78 x 85mm
(3.1 x 3.1 x 3.3”)
0.42kg (0.93lbs)
Dimensions (H x W x D)
High gloss black
High gloss white
Weight
Finishes
87dB (2.83 Vrms input)
120Hz-20kHz
8 Ohms compatible
25-200W*
1 x 2.25" BMR
1 x 2.25" longthrow woofer
154 x78 x 85mm
(6.0 x 3.1 x 3.3”)
0.85kg (1.88lbs)
High gloss black
High gloss white
*Using a high powered amplifier lower down its volume scale results in lower distortion and better sound. Of course if you hear a distorted sound or mechanical ‘crack’ as the speakers hit their end stops, you are playing the speakers too loud and this may cause damage. With an AVR the Min11/21 speakers should be set to ‘small’ with a crossover frequency of 140Hz. In this configuration, power handling is considerable increased.
www.cambridge-audio.com
Minx Subwoofer Specifications
cm
35.5
33
30.5
28
25.5
23
20.5
18
15.5
13
10.5
8
X200 X300 X500
I
Powerful DSP design delivering awesome performance from the smallest footprint possible
I
Powerful 200W, 300W and 500W digital amplifiers
I One piece aerospace grade aluminium cones move air with incredible efficiency
I
DSP design allows far smaller cabinet construction than comparative subwoofers
I
Supplied with removable grilles
I Full rear panel control of gain, phase and crossover frequency allowing optimum integration and room positioning
I
Driver plus ABR (Auxillary Bass Radiator) configuration. ABRs replace bass ports to eliminate air noise at high levels
I
Scratch resistant high gloss lacquer available in black or white finishes
X200 specifications X300 specifications X500 specifications
Power Output
Frequency Response
Crossover
200W
39Hz (-6dB) – 200Hz
Active – variable 50Hz-200Hz
Mains voltage 100V/110-120V/220-240V
Drivers 1 x 6.5" subwoofer
2 x 6.5" passive radiator
Dimensions
(H x W x D)
Weight
Finishes
219 x 210 x 222mm
(8.6 x 8.3 x 8.7")
5.0Kg (11.0lbs)
High gloss black
High gloss white
Power Output
Frequency Response
Crossover
300W
33Hz (-6dB) – 200Hz
Active – variable 50Hz-200Hz
Mains voltage
Drivers
100V/110-120V/220-240V
1 x 8" subwoofer
1 x 8" passive radiator
Dimensions
(H x W x D)
Weight
Finishes
311 x 266 x 278mm
(12.4 x 10.5 x 11.0")
7.5Kg (16.5lbs)
High gloss black
High gloss white
Power Output
Frequency Response
Crossover
500W
23Hz (-6dB) – 200Hz
Active – variable 50Hz-200Hz
Mains voltage
Drivers
100V/110-120V/220-240V
1 x 10" subwoofer
1 x 10" passive radiator
Dimensions
(H x W x D)
Weight
Finishes
365 x 320 x 350mm
(14.3 x 12.6 x 13.8")
11.7Kg (25.8lbs)
High gloss black
High gloss white
www.cambridge-audio.com
5"
4"
3"
8"
7"
6"
2"
1"
Inches
14"
13"
12"
11"
10"
9"
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement