U
SER
G
UIDE
Cisco Unified IP Phones 7945G and 7965G for
Cisco Unified Communications Manager Express 4.3
1
Overview
2
Operating Your Phone
3
Phone Features Index
1
Overview
This guide provides phone operating instructions, and features descriptions for the Cisco Unified IP Phone multiline models 7945G and 7965G. The 7945G has four lines and the 7965G has six lines.
2
Physical Description
17 1 2
16
Name
1
Line or speed-dial button
2
Footstand adjustment
Display button
3
4
Messages button
5
Directories button
6
Help button
7
Settings button
8
Services button
9
Volume button
3
4
5
6
7
8
9
15 14 13 12 11 10
Description
Opens new line, speed-dials phone number, or ends call. Buttons light to indicate status:
Green, steady: Active call or two-way intercom call
Green, flashing: Held call
Amber, steady: Privacy in use, one-way intercom call, DnD active.
Amber, flashing: Incoming call or reverting call
Red, steady: Remote line in use (shared line or BLF status)
Allows you to adjust angle of phone base.
Awakens the phone screen from sleep mode.
Provides access to message (voice mail) system.
Provides access to phone directories.
Activates Help menu.
Provides access to phone settings such as display contrast and ring type.
Provides access to phone services.
Increases or decreases handset, headset, ringer, or speakerphone volume.
Name (continued)
10
Speaker button
11
Mute button
Description (continued)
Toggles speaker on and off.
Toggles mute on and off.
12
Headset button Toggles headset on and off.
13
4-way Navigation Pad and
Select (center) button .
14
Keypad
15
Soft keys buttons
16
Handset with indicator light
17
LCD screen
Allows you to scroll through menus and highlight items, displays phone numbers from your Placed Calls, when phone is on-hook. Use Select button to select an item that is highlighted on the screen.
Navigation button:
•
Scroll up and down to see menus and highlight items.
•
Scroll left to open the Details view and see directory numbers and features assigned to each line button (when on call screen).
•
Scroll right to close the Details view.
Select button: scroll to select a line using the Navigation button, then:
If the button is mapped to a directory number, and:
–
The line is idle, press to initiate a new call.
–
–
There is an on-hold call on the line, press to resume the call.
There is an active call on the line, the Select button has no effect.
If the button is mapped to a feature, press to access the feature.
Functions as traditional telephone keypad.
Engages functions visible on corresponding LCD tabs.
Functions as traditional handset and provides message waiting indicator light and message-waiting (stutter) tone.
Displays information such as line/call status, phone number, and soft key tabs.
3
4
Connecting Your Phone
This section shows and describes the connectors on your Cisco Unified IP phone.
1
AUX 10/100 SW 10/100 PC
DC48V
3
2
5
4
2
3
4
6
7
8
1
5
DC adapter port (DC48V) for phones not provided with inline power
AC-to-DC power supply
AC power cord
Network port (10/100 SW) for connecting to the network
Access port (10/100 PC) for connecting your phone to your computer
Handset port
Headset port
Footstand button
6
7
Adjusting the Handset Rest
When you connect your phone, you can adjust the handset rest so that the receiver will not slip out of the cradle. To adjust the handset:
1.
Set the handset aside and pull the square plastic tab from the handset rest.
2.
Rotate the tab halfway.
3.
Slide the tab back into the handset rest. An extension protrudes from the top of the rotated tab. Return the handset to the handset rest.
1 2 3
2
Operating Your Phone
This section describes how to operate your Cisco Unified IP phone and includes information on soft keys and phone features.
Note
Because there are differences in phone and site configurations, not all features described here may apply to your phone.
Consult your administrator for more information.
Soft Key
<< or >>
Answer
Callback
Cancel
CFwdALL
Clear
Confrn
Delete
Dial
Soft Key Descriptions
Your Cisco Unified IP phone is equipped with soft keys for call features and options. Soft keys are displayed along the bottom of the LCD screen and activated using the corresponding buttons. Soft keys can change according to the state of the phone.
Following is a comprehensive list of soft keys offered on these Cisco Unified IP Phones. Functions depends on your system configuration.
Function
Navigates to edit characters. Use the backspace soft key to erase digits that you entered incorrectly.
Answers an incoming call.
Notifies callers that the called line is free.
Cancels the last selection.
Forwards all calls.
Clears directory history.
Connects callers to a conference call.
Deletes selected number.
Dials the displayed number.
5
6
Soft Key
DnD
Down
EditDial
EndCall
Exit
Flash
GPickUp
Hold
LiveRcd
Login more
NewCall
Ok
Park
PickUp
Play
Redial
RmLstC
Resume
Save
Search
Select
Trnsfer
TrnsfVM
Up
Function
Enables the Do-Not-Disturb feature.
Decreases the LCD screen contrast.
Selects a number and activates the cursor for editing.
Ends the current call.
Exits from current selection.
Provides hookflash functionality for three-way calling and call waiting services provided by the PSTN or Centrex service.
Selectively picks up calls coming into a phone number that is a member of a pickup group.
Places an active call on hold. Resumes call on hold.
Enables the user to record a phone conversation.
Provides PIN-controlled access to restricted phone features. Contact your administrator for instructions.
Scrolls through additional soft key options (for example, use more soft key to locate the
DnD soft key).
Opens a new line on the speakerphone to place a call.
Confirms the selection.
Forwards calls to location from which calls can be retrieved by anyone in the system.
Selectively picks up calls coming into another extension.
Plays ring sound sample.
Redials last number dialed.
Removes Last Participant from the Conference Call.
Returns to active call.
Saves last change.
Initiates search in local directory.
Selects highlighted option.
Transfers active calls to another extension.
Transfers a call to voice mail.
Increases LCD screen contrast.
Place a Call
Use one of the following methods to place a call:
•
Lift the handset and dial the number.
•
Dial the number, and then lift the handset.
•
Dial the number, and then press the Dial soft key.
•
Press the line button for your extension, and then dial.
•
Press the Speaker button, and then dial.
•
Press the New Call soft key, and then dial.
•
If you are using a headset, press the Headset button, and then dial.
•
Dial the number, and then press the Headset button.
•
If you have established speed-dial numbers, press a speed-dial button.
•
If you have selected a number from a directory, press the Dial soft key.
Note
Use the backspace (<< ) soft key to erase digits that you enter incorrectly.
Answer a Call
To answer a call:
•
Lift the handset.
•
If you are using a headset, press the Headset button. If necessary, press the line button to select between incoming calls.
•
If you are using the speakerphone, press the Answer soft key or the Speaker button.
End a Call
To end a call:
•
Hang up the handset.
•
If you are using a headset, press the Headset button or the EndCall soft key.
•
If you are using a speakerphone, press the Speaker button or the EndCall soft key.
Redial a Number
To redial the most recently dialed number:
•
Lift the handset and press the Redial soft key.
•
Press the Redial soft key to dial using the speakerphone.
Hold a Call
To place a call on hold while on the call:
•
Press the Hold soft key.
To retrieve a held call:
•
Press the Resume soft key.
–
–
If multiple calls are on hold, use the Navigation button to select the desired call before you press Resume.
If multiple calls on multiple lines are on hold, press the line button for the line that you want to pick up. The active call on the other line is automatically put on hold.
Note
Because the hold feature can generate music or tones, avoid using hold when dialed into a remote conference system.
Conferences that are created locally on your phone can safely be placed on hold without introducing music or tones into the conference.
Mute a Call
To mute a call:
•
While on a call, press the Mute button. The Mute button lights, indicating that the other party cannot hear you.
To deactivate the mute function, do one of the following:
•
Press the Mute button again.
•
Lift the handset if you are using mute with your speakerphone.
Note
The Mute feature does not generate music or a tone.
7
Manage Call Waiting
If you are on a call when a second call comes in, you hear a call-waiting tone or see a flashing indicator light on the handset rest, depending on the configuration of your phone.
To answer the new call on the same line:
1.
Use the Navigation button to select the call
2.
Press the Answer soft key to answer the call. The call on the other line is automatically put on hold.
To return to the original call:
1.
Use the Navigation button to reselect the call.
2.
Press the Resume soft key to reconnect to the call.
For calls on a separate line:
•
Press the Line button for the incoming call. The call on the other line is automatically put on hold.
To return to the original call:
•
Press the Line button associated with the original call.
Retrieve Voice Messages
To retrieve voice messages:
1.
Select an available Cisco Unified IP phone line by lifting the handset, pressing the speakerphone button, or pressing a line button. Listen for the dial tone.
2.
Press the Messages button, and follow the voice instructions.
Note
When you have one or more new messages, the message-waiting indicator (MWI) on your handset is lit. The MWI works only if the MWI is configured on your phone.
Note
Your company determines the voice message service that your phone system uses. For the most accurate and detailed information, refer to the documentation that came with your voice message service.
8
Adjust the Volume for the Current Call
To adjust the handset, speakerphone, or headset volume for the current call:
1.
During a call, press the Up or Down Volume button.
2.
Press the Save soft key to apply the new volume level to future calls.
Adjust the Ring Volume
•
Press the Up or Down Volume button while the handset is in its cradle and the phone is idle.
Select the Ring Type
To change the ringer sound:
1.
Press the Settings button.
2.
Press 2 for Ring Type, or use the Navigation button to scroll to Ring Type and press the Select soft key.
3.
Use the Navigation button to scroll through the list of ring types. Press the Play soft key to hear samples.
4.
Highlight the ring you want, and then press the Select soft key.
5.
Press the Ok soft key to select your setting.
6.
Press the Save soft key to save the setting, or press Cancel to exit to the previous menu without changing the setting.
7.
Press the Exit soft key to go to the main directory menu.
Adjust the Display Contrast
To adjust the contrast in your LCD display:
1.
Press the Settings button.
2.
Press 1 for Contrast, or use the Select soft key.
3.
Use the Down or Up soft key to change the contrast.
4.
Press the Ok soft key
5.
Press the Save or Exit soft key.
6.
Press the Ok soft key to select your contrast setting.
7.
Press the Save soft key to save the setting, or press Cancel to exit to the previous menu without changing the setting.
8.
Press the Exit soft key to go to the main directory menu.
Note
In the following procedures, you may need to enter information using the keypad. Press the backspace (<<) soft key to erase digits that you enter incorrectly.
Divert Incoming Calls
To forward any incoming call to the call-forward destination, for example voice mail, preset set on the Cisco Unified IP phone:
•
Press the DnD soft key.
Note
If the call-forward destination is not set, pressing the DnD soft key disables the ringer.
Park a Call
Call park allows a phone user to place a call on hold at a designated parking spot from which the call can be retrieved by anyone on the system.
Note
Contact your administrator for your call park slot number.
To park a call:
•
Press the Park soft key.
The Cisco Unified Communications Manager Express system automatically selects an available call park slot and displays the number on the Cisco Unified IP phone screen.
To park a call to a specific call park slot:
•
Press the transfer button followed by the call park slot number provided by your administrator.
To retrieve a parked call:
•
If your phone receives a call park notification, press the PickUp soft key followed by the asterisk (*).
•
Press the PickUp soft key followed by the call park slot number.
Call-Blocking (Toll Bar) Override
Call blocking prevents unauthorized use of phones. It is implemented by matching a pattern of specified digits during a specified time of day and day of week or date. The call-blocking override feature allows individual phone users to override the predefined call blocking.
Note
Contact your administrator for your personal identification number (PIN).
9
To place calls when call-blocking is enabled:
1.
Press the Login soft key on the Cisco Unified IP phone.
2.
Enter the Personal Identification Number (PIN) that is associated with the phone.
Transfer a Call
To transfer a selected call to another number, you can use blind transfer or consultative transfer:
Blind Transfer
Immediately redirects the call without allowing you to speak to the transfer recipient (the person to whom you are transferring the call).
To make a blind transfer call, use the following method:
1.
During a call, press the Trnsfer soft key. The call is placed on hold.
2.
Dial the number to which you want to transfer the call.
Consultative Transfer
Redirects the call after first allowing you to speak to the transfer recipient.
To make a consultative transfer, use the following method:
1.
During a call, press the Trnsfer soft key. The call is placed on hold.
2.
Dial the number to which you want to transfer the call.
3.
Wait for the call to be answered. Speak to the transfer recipient. Then press the Trnsfer button or hang up the handset.
4.
If the transfer fails, press the Resume soft key to return to the original call.
Cancel Transfer
1.
To cancel your consult call-transfer attempt:
–
Press the EndCall soft key.
2.
To reconnect to the original caller:
–
Press the Resume soft key.
Transfer to Voice Mail
1.
Press TrnsfVM.
2.
Enter the recipient’s extension number and press TrnsfVM again.
Forward All Calls
To forward all incoming calls to another number:
1.
Press the CFwdALL soft key. You hear a confirmation beep.
2.
Dial the number to which you want to forward all your calls. Dial the number exactly as if you were placing a call to that number. Remember to include locally required prefix numbers.
The phone display is updated to show that calls will be forwarded.
3.
Press the pound key (#) or the EndCall soft key.
Note
To forward calls to voice mail, manually enter the voice mail number, or use the CFwdALL soft key plus the Messages button, followed by the EndCall soft key. When call forward all is set, the display will show Call Forward Icon.
To forward calls to a speed-dial number, use the CFwdALL soft key plus a speed-dial button, followed by the EndCall soft key.
10
To cancel call forwarding, use one of the following methods:
•
Press the CFwdALL soft key.
Pick Up Calls
To pick up a call that is on hold or a call that is ringing at another extension:
1.
Press the PickUp soft key.
2.
Dial the extension number of the Cisco Unified IP phone that you want to pick up. Control of the call is transferred to your phone.
To selectively pick up a call ringing at a number that belongs to a pickup group:
•
Press the GPickUp soft key. If only one pickup group is defined in the entire Cisco Unified Communications Manager
Express system, control of the call is transferred to your phone.
•
If the ringing telephone and your phone are in the same pickup group, press the asterisk (*) to transfer control of the call to your phone.
•
If the ringing telephone and your phone are in different pickup groups, dial the pickup group number where the phone is ringing to transfer control of the call to your phone.
Place and Establish a Conference Call
To create a three-party conference call, perform the following steps:
1.
During a call, press the more soft key and then the Confrn soft key to open a new line and put the first party on hold.
2.
Place a call to another number.
3.
When the call connects, press Confrn again to add the new party to the call.
To establish a conference call between two- and three-party calls to a Cisco Unified IP phone, one active and the other on hold:
•
Press the Confrn soft key on the Cisco Unified IP phone.
To establish a conference call between second- and third-party calls already present on a Cisco Unified IP phone, using separate line buttons, one active and the other on hold, perform the following steps:
1.
Press the Confrn soft key on the Cisco Unified IP phone.
2.
Press the Line button of the call you want to add to the conference.
Note
Your system administrator will have configured the system for three-party or eight-party ad-hoc conferences.
Place a MeetMe Conference Call
To Place a MeetMe conference call:
1.
Obtain a MeetMe conference number from your administrator
2.
Distribute the MeetMe conference number to all the participants.
3.
Go offhook, press the MeetMe softkey, and dial the MeetMe conference number. All other participants join the meeting by dialing into the MeetMe conference number.
•
To end the MeetMe conference call, all participants must hang up the handset or press the EndCall soft key.
End a Conference Call
To end the conference call:
•
Hang up the handset, or press the EndCall soft key.
Note
Depending on configuration when the conference call initiator disconnects, the conference call terminates.
11
Alternate Methods to End a Conference Call
Call initiators may use one of the following methods (functionality will vary according to your system configuration):
•
To end the conference and remain connected to the most recent call, press the Confrn soft key. The older call is placed on hold.
•
To disconnect from the conference, hang up the handset. The other parties remain on the conference call.
Live Record a Call
Call initiators can use the LiveRcd soft key to record an active call, private line or conference call. To record a call, use this method:
1.
Press the LiveRcd. This puts the other party on-hold and initiates a call to the configured live record number.
2.
Press the LiveRcd again to stop the recording.
Join a Shared-Line Call
User can join a call on a shared line using the cBarge softkey.
To join the shared-line call, use the following method:
1.
Highlight the remote-in-use call that you want to join.
2.
Press the more to navigate to cBarge and press cBarge.
Place a Call from Your Local Directory
To access the local phone directory established by the administrator:
1.
Press the Directories button.
2.
Press the Navigation Up or Down button or press 4 to select the Local Directory.
3.
Press the Navigation Up or Down button to select the Last, First, or Number field search option.
4.
Using the keypad, enter the last name or first name for the entry.
When entering letters, select the appropriate number key of the letter you want, and press that key a number of times that equals the position of the target letter. For example, to enter a B, press the 2 key two times, and to enter a C, press the 2 key three times. Use the backspace (<<) soft key to make corrections while entering data.
5.
Press the Search soft key to find your selection.
6.
If your search results in multiple listings, use the Navigation Up or Down button to select the correct number.
7.
Press the Dial soft key to dial the selected number.
Program Personal Speed-Dial Buttons
After an administrator defines one or more speed-dial instances for a Cisco Unified IP phone, you can reprogram numbers that are not locked or program numbers into an instance that has an empty dial string:
1.
Select an available phone line by lifting the handset, by pressing the NewCall soft key, or by pressing a line button. Listen for the dial tone.
2.
Press the pound key (#).
3.
Press the speed-dial button that you want to program. A short beep confirms that you are starting to program this button.
4.
Enter the speed-dial number. The digits appear on the phone display. When you are entering speed-dial numbers, use the backspace (<<) soft key to erase digits that you entered incorrectly.
•
To remove a speed-dial number without replacing it with a new one.
1.
Press the pound key (#).
2.
Press the same speed-dial button a second time to indicate that you are done entering the speed-dial digits and to store the new speed-dial number.
3.
Hang up the handset, or press a new speed-dial button and repeat this procedure.
12
Place a Call from Your System Speed-Dial Directory
To place a call from your system speed-dial directory:
1.
Select an available Cisco Unified IP phone line (off hook or NewCall) and get a dial tone.
2.
Press the Directories button, or use the Navigation button to locate Directory and then press the Select soft key.
3.
Use the Navigation button to scroll through the options. Use the Select soft key to select speed-dial options.
–
–
Press 5 for the Local Speed Dial.
Press 6 for the Personal Speed Dial (functionality varies depending on your system configuration).
4.
Use the Navigation button to scroll through the speed-dial phone list.
5.
To dial the selected phone number, either press the Select soft key or enter the number on the keypad.
6.
Press the Exit soft key to go to the directory menu.
View Call History
To view recent missed, received, or placed calls:
1.
Press the Directories button.
2.
Use the Navigation button to scroll and select the desired call list. Press the Select soft key, or:
–
–
Press 1 on the keypad for Missed Calls.
Press 2 on the keypad for Received Calls.
–
Press 3 on the keypad for Placed Calls.
3.
Press the Exit soft key to return to the previous directory menu.
Place a Call from Call History
To place a call to a number in the call history list:
1.
Use the Navigation button to scroll through the call history list.
2.
Use the Select soft key to select a phone number. The digits appear on the phone display.
3.
To dial the number as it appears on the phone display:
–
Press the Dial soft key.
To edit the number on the phone display before dialing:
1.
Press the EditDial soft key to place the cursor at the beginning of the number on the phone display.
2.
Use the keypad to edit the digits as needed. Use the backspace (<<) soft key to erase digits that you enter incorrectly.
3.
Press the Dial soft key to place the call.
Clear Call History
To clear all numbers in the directory histories:
•
Press the Clear soft key.
Note
The Clear soft key clears all call history lists. Selective clearing of call history lists is not supported.
Use the Intercom Feature
Cisco Unified Communications Manager Express supports intercom functionality for one-way and press-to-answer voice connections using a dedicated pair of intercoms on two phones that speed-dial each other.
To use the intercom feature:
1.
Press the Speaker button and get the dial tone.
2.
Press the speed dial key or dial the directory number to start the intercom call.
13
14
Note
The called Cisco Unified IP phone automatically answers the call in speakerphone mode with mute activated or deactivated depending on configuration. The phone will beep to alert the recipient to the incoming call.
To respond to an intercom call:
•
If Mute key is lighted, Press the Mute button, or lift the handset.
•
If Mute key is not lighted, reply to caller handsfree.
Activate Do Not Disturb
For visual call alerting and information without audible ringing, use Do Not Disturb (DnD). Calls receive normal call-forward-busy and no-answer treatment.
To activate the Do-Not-Disturb feature:
1.
Press the more soft key to locate the DnD soft key.
2.
Press the DnD soft key. A text message displays to indicate that the phone is in Do-Not-Disturb mode.
Note
Pressing the DnD soft key immediately forwards the call to the call-forward destination set on the phone. If the call-forward destination is not set, pressing the DnD soft key disables the ringer.
To deactivate the Do-Not-Disturb feature, repeat Steps 1 and 2.
Place a Call Using Your Extension Mobility (EM) Profile
Extension Mobility (EM) allows the user to temporarily configure a Cisco Unified IP phone to function as user’s own phone.
Once the user is logged-in to EM, the phone adopts the user’s profile, including the line buttons, features, and established services.
To log-in to Extension Mobility:
1.
Press Services button and select Extension Mobility.
2.
Enter your User ID and Password.
3.
Press Submit. The phone will temporarily configure user profile and settings.
Note
Your administrator must configure Extension Mobility for you.
Place a Call from Your Personal Speed-Dial
To place a call from your Personal Speed-Dial using My Phone Apps, use the following method:
1.
Log-in to Extension Mobility.
2.
Select My Phone Apps and scroll down to Personal Speed Dial.
3.
Select Personal Speed Dial
4.
Add a Label and Number
5.
Go back to My Phone Apps and press Reset Phone. You Personal Speed-Dial number will appear on the phone display screen.
3
Phone Features Index
This section provides an alphabetical list of features for your Cisco Unified IP phone. Features supported in both SIP and SCCP protocols are marked as “Supported” and features not supported in either one of the protocols are marked as “Not Supported”.
However, there are differences in how the feature works based on the call protocol.
Table 1 Features (with page number references) supported in SIP and SCCP protocols.
Features
Activate Do Not Disturb 15
Adjust the Display Contrast 10
Adjust the Ring Volume 10
Adjust the Volume for the Current Call 9
Answer a Call 8
Call-Blocking (Toll Bar) Override 11
Clear Call History 14
Divert Incoming Calls 10
End a Call 8
End a Conference Call 13
Forward All Calls 11
Hold a Call 8
Join a Shared-Line Call 12
Live Record a Call 12
Manage Call Waiting 9
Mute a Call 9
Park a Call 10
Pick Up Calls 12
Place a Call 8
Place a Call from Call History 14
Place a Call from Your Local Directory 13
Place a Call from Your Personal Speed-Dial 14
Place a Call from Your System Speed-Dial Directory 14
Place a MeetMe Conference Call 12
Place and Establish a Conference Call 12
Program Personal Speed-Dial Buttons 13
Place a Call Using Your Extension Mobility (EM) Profile 14
Redial a Number 8
Retrieve Voice Messages 9
Select the Ring Type 10
Transfer a Call 11
Use the Intercom Feature 14
View Call History 14
SIP
Supported
Supported
Supported
SCCP
Supported
Supported
Supported
Supported
Supported
Supported
Supported
Not Supported Supported
Supported Supported
Supported
Supported
Supported
Supported
Supported
Supported
Supported
Supported
Supported Supported
Not Supported Supported
Not Supported Supported
Supported Supported
Supported Supported
Not Supported Supported
Not Supported Supported
Supported Supported
Supported
Supported
Supported
Supported
Not Supported Supported
Supported Supported
Not Supported Supported
Supported Supported
Not Supported Supported
Not Supported Supported
Supported
Supported
Supported
Supported
Supported
Supported
Supported
Supported
Supported
Supported
Supported
Supported
15
Americas Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA www.cisco.com
Tel: 408 526-4000
800 553-NETS (6387)
Fax: 408 527-0883
Asia Pacific Headquarters
Cisco Systems (USA) Pte. Ltd.
168 Robinson Road
#28-01 Capital Tower
Singapore 068912 www.cisco.com
Tel: +65 6317 7777
Fax: +65 6317 7799
Europe Headquarters
Cisco Systems International BV
Haarlerbergpark
Haarlerbergweg 13-19
1101 CH Amsterdam
The Netherlands www-europe.cisco.com
Tel: 31 0 800 020 0791
Fax: 31 0 20 357 1100
Cisco has more than 200 offices worldwide. Addresses, phone numbers, and fax numbers are listed on the
Cisco Website at www.cisco.com/go/offices.
Cisco, Cisco Systems, the Cisco logo, and the Cisco Systems logo are registered trademarks or trademarks of Cisco Systems, Inc. and/or its affiliates in the United States and certain other countries. All other trademarks mentioned in this document or Website are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (0705R)
© 2008 Cisco Systems, Inc. All rights reserved.
Printed in the USA on recycled paper containing 10% postconsumer waste.
OL-xxxxx-xx
