WinSystems MCM/LPM-TX Embedded Computer System Operations Manual
The MCM/LPM-TX is a small, high-performance, embeddable computer system on a single STD-Bus board. It integrates a number of popular I/O options including Solid-State Disk. Two PC compatible serial ports are standard, as are the floppy, hard disk, and parallel printer interfaces. The MCM/LPM-TX is populated with an Intel Pentium 166MMX. Up to 64MB of onboard DRAM, 512KB of pipeline burst, level two cache is also standard. A full 16-bit PC/104 expansion bus is provided for further expansion to an entire industry of add-on peripherals including sound and speech modules, SCSI controllers, Analog I/O modules, and literally hundreds of other options available from WinSystems’ and a variety of vendors supporting the PC/104 and PC/104-Plus standards. An onboard 32-pin silicon disk socket supports the M-Systems’ DiskOnChip Flash modules in sizes ranging from 8 Megabytes to 288 Megabytes.
Advertisement
Advertisement
OPERATIONS MANUAL MCM/LPM-TX WinSystems reserves the right to make changes in the circuitry and specifications at any time without notice. © Copyright 2001 by WinSystems. All Rights Reserved. WinSystems - "The Embedded Systems Authority" REVISION HISTORY P/N 403-0296-000 ECO Number ORIGINATED Date Code 010910 Rev Level C TABLE OF CONTENTS Section Number Paragraph Title Page Number 1 1.1 1.2 1.3 General Information Features General Description Specifications 1-1 1-1 1-2 2 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 2.10 2.11 2.12 2.13 2.14 2.15 2.16 2.17 2.18 2.19 2.20 MCM/LPM-TX Technical Reference Introduction Intel FW82439TX Chipset CPU Speed Select Interrupt Routing Headers Serial Interface Watchdog Timer Battery Select STD-Bus Interface DiskOnChip Configuration Multi I/O Connector USB Connector PC/104 Bus Interface PC/104-Plus Bus Interface IDE Interface Floppy Interface Mouse Connector CPU Fan Connector Parallel Printer Port Status LED Jumper/Connector Summary 2-1 2-1 2-2 2-3 2-4 2-10 2-11 2-12 2-13 2-14 2-14 2-15 2-16 2-17 2-17 2-18 2-18 2-19 2-19 2-20 3 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 3.10 3.11 3.12 3.13 3.14 Award BIOS Configuration General Information Entering Setup Setup Main Menu Standard CMOS Setup BIOS Features Setup Chipset Features Setup Power Management PNP/PCI Configuration Load BIOS Defaults Load Setup Defaults Password Setting IDE HDD Auto Detection Save and Exit Setup Exit Without Saving 3-1 3-1 3-1 3-1 3-2 3-7 3-11 3-13 3-19 3-20 3-21 3-21 3-21 3-21 3-21 4 4.1 MCM-TX DiskOnChip Configuration 4-1 4-1 DiskOnChip Usage WinSystems - "The Embedded Systems Authority" APPENDIX A I/O Port Map APPENDIX B Interrupt Map APPENDIX C MCM/LPM-TX Parts Placement Guide APPENDIX D MCM/LPM-TX Parts List 1 General Information 1.1 Features n n n n n n n n n n n n n 1.2 Intel Tillamook Pentium MMX 166MHz with 32KB of L1 cache and 512KB of onboard pipeline L2 cache 32MB or 64MB of system SDRAM Socket for up to 288MB bootable DiskOnChip or BIOS extension EPROM Industry standard Award BIOS Two RS-232 serial ports with 16 byte FIFO with optional RS-422/485/J1708 support on both channels USB (Universal Serial Bus) support Ultra DMA/33 IDE Hard drive controller PC/104 and PC/104- Plus expansion connectors AT keyboard controller and PS2 mouse support Two interrupt controllers and 7 DMA channels Three 16-bit counter/timers On-board CPU power supply Extended operating temperature available for CMOS STD Bus -40°C to +85°C General Description The MCM/LPM-TX is a small, high-performance, embeddable computer system on a single STD-Bus board. It integrates a number of popular I/O options including Solid-State Disk. Two PC compatible serial ports are standard, as are the floppy, hard disk, and parallel printer interfaces. The MCM/LPM-TX is populated with an Intel Pentium 166MMX. Up to 64MB of onboard DRAM, 512KB of pipeline burst, level two cache is also standard. A full 16-bit PC/104 expansion bus is provided for further expansion to an entire industry of addon peripherals including sound and speech modules, SCSI controllers, Analog I/O modules, and literally hundreds of other options available from WinSystems’ and a variety of vendors supporting the PC/104 and PC/104-Plus standards. An onboard 32-pin silicon disk socket supports the M-Systems’ DiskOnChip Flash modules in sizes ranging from 8 Megabytes to 288 Megabytes. 010911 OPERATIONS MANUAL MCM/LPM-TX Page 1-1 1.3 Specifications 1.3.1 Electrical Bus interface : STD-8088/188 Compatible PC/104 8-bit or 16-bit expansion bus PC/104-Plus 32-bit expansion bus System Clock : 66MHz Interrupts : TTL Level input VCC : +5V +/-5% at 1.5A typical with an Intel Pentium166MMX processor with 32M SDRAM VCC1 : +12V +-5% (Not required. PC/104 Expansion only) VCC2 : -12V +-5% (Not required. PC/104 Expansion only) 1.3.2 Memory Addressing : 64 Megabyte addressing BIOS ROM : 128K Atmel Flash Memory : Factory installed SMT DRAM in sizes 32M or 64M SSD Memory : One 32-pin JEDEC standard socket supporting the M-Systems’ 32-Pin DOC (DiskOnChip) module. 1.3.3 Mechanical Dimensions : 4.5” X 7” (without STD-Bus modules or cables) PC-Board : FR4 Epoxy Glass with 4 signal layers and 2 power planes with screened Component legend, and plated through holes Jumpers : 0.025” square posts on 0.10” centers Connectors : Multi I/O : 50-pin RN type IDH-50-LP Floppy Disk : 34-pin RN type IDH-34-LP Fixed Disk : 40-pin RN type IDH-40-LP PC/104 Bus 64-pin SAMTEC type ESQ-132-12-G-D 40-pin SAMTEC type ESQ-120-12-G-D Page 1-2 OPERATIONS MANUAL MCM/LPM-TX 010911 WinSystems - "The Embedded Systems Authority" PC/104- Plus : COMM CON 50808-120Q Fan Power : 3-pin Molex type 22-11-2032 Mouse : 5-pin in line latching Molex type 22-11-2052 USB : 4-pin in line latching Molex type 22-11-2042 OTT Interrupt Header : 10-pin RN type IDH-10-LP 1.3.4 Environmental Operating Temperature : -40°C to +85°C using Pentium 166MHz Non-condensing relative humidity : 5% to 95% 010911 OPERATIONS MANUAL MCM/LPM-TX Page 1-3 WinSystems - "The Embedded Systems Authority" This Page Intentionally Left Blank Page 1-4 OPERATIONS MANUAL MCM/LPM-TX 010911 2 MCM/LPM-TX Technical Reference 2.1 Introduction This section of the manual is intended to provide sufficient information regarding the configuration and usage of the MCM/LPM-TX board. WinSystems maintains a Technical Support group to help answer questions regarding configuration, usage, or programming of the board. For answers to questions not adequately addressed in this manual, contact Technical Support at (817) 274-7553 between 8AM and 5PM Central Time. 2.2 Intel FW82439TX Chipset The MCM/LPM-TX utilizes the Intel FW82439TX Chipset which provides a highlyintegrated, high-performance backbone for full Pentium class compatibility. The Chipset contains the logic for DRAM and bus state control as well as the standard complement of 'AT' class peripherals, including : Two-82C37 DMA controllers Two-82C59 Interrupt controllers 82C54 Timer/Counter Real Time Clock Enhanced Power Management Full PnP compatibility UDMA/33 EIDE controller These functional units are 100% PC/AT compatible and are supported by the Award BIOS and setup. Users desiring to access these internal peripherals directly should refer to any manufacturers generic literature on the equivalent discrete component. There are a number of internal registers within the Intel TX chipset that are used by the BIOS for control and configuration. Refer to the I/O map in Appendix A for port usage to avoid conflicts when adding external I/O devices. 010911 OPERATIONS MANUAL MCM/LPM-TX Page 2-1 WinSystems - "The Embedded Systems Authority" CPU Speed Select 2.3 J13 1o 2o 3o J14 1o 2o 3o J15 1o 2o 3o The MCM/LPM-TX uses a crystal controlled frequency synthesizer to control the base CPU clock frequency. The jumper blocks at J13, J14, and J15 allow for the selection of the clock multiplier for the processor. The processors available from WinSystems and the jumpering for them are shown in the chart below. Jumpers Intel 166MHz Intel 266MHz J13 2-3 2-3 J14 2-3 2-3 J15 2-3 1-2 NOTE : The MCM/LPM-TX board will be jumpered at the factory for the rated speed of the installed processor. Jumpering to any other configuration may result in CPU overheating, misoperation, and possible destruction of the CPU. Failures of CPUs which have been operated above their rated speed, or temperature, are not covered under the WinSystems standard product warranty. Page 2-2 OPERATIONS MANUAL MCM/LPM-TX 010911 WinSystems - "The Embedded Systems Authority" Interrupt Routing Headers 2.4 2 4 6 8 10 ooooo ooooo 13 579 J4 Over The Top Interrupt Header J4 J19 Interrupt Routing Header J19 1oo2 3oo4 5oo6 7oo8 9 o o 10 11 o o 12 13 o o 14 15 o o 16 17 o o 18 19 o o 20 21 o o 22 23 o o 24 25 o o 26 27 o o 28 29 o o 30 31 o o 32 All interrupt inputs are routed to the appropriate PC/104 bus pins to the PC/104 connector at J27. The Hard Disk is routed to its interrupt input using the jumper block at J19. The block allows disconnecting or rerouting of the onboard peripherals. An Over The Top (OTT) connector is also provided at J4 to allow front-plane routing of additional interrupt inputs. The pin definitions for J19 and J4 are shown here : J19 J4 GND GND GND GND GND 010911 1oo2 3oo4 5oo6 7oo8 9 o o10 To J19 pin 1 To J19 pin 3 To J19 pin 5 To J19 pin 7 To J19 pin 11 From J4 pin 2 From J4 pin 4 From J4 pin 6 From J4 pin 8 IDE From J4 pin 10 STD pin 46 STD pin 50 STD pin 44 STD pin 37 STD pin 44 STD pin 37 STD pin 50 STD pin 44 STD pin 46 Speaker OPERATIONS MANUAL MCM/LPM-TX 1oo2 3oo4 5oo6 7oo8 9 o o 10 11 o o 12 13 o o 14 15 o o 16 17 o o 18 19 o o 20 21 o o 22 23 o o 24 25 o o 26 27 o o 28 29 o o 30 31 o o 32 IRQ10 IRQ11 IRQ12 IRQ14 IRQ14 IRQ15 IRQ9 IRQ9 IRQ7 IRQ7 IRQ6 IRQ5 IRQ4 IRQ3 IOCHK IRQ5 Page 2-3 WinSystems - "The Embedded Systems Authority" 2.5 Serial Interface J8 J9 12 3 ooo 12 3 ooo J10 J12 1o 2o 3o 12 3 ooo The MCM/LPM-TX provides two RS-232 serial channels onboard. The two serial ports, COM1 and COM2 are configurable for RS-422, RS-485 or J1708, with the addition of optional driver ICs. The configuration options for each of the supported modes are shown on the following pages. Connection to COM1 and COM2 is made through the Multi-I/O connector at J2. An adapter cable (P/N CBL-247-1) is available from WinSystems to adapt to standard DB9 connectors. 2.5.1 COM1 RS-232 COM1 is I/O mapped at 3F8H and utilizes a 16550 type UART contained in the SuperI/O chip. When used in RS-232 mode, COM1 is terminated via the Multi-I/O connector at J2. The configuration details and the pin definitions when used with the CBL-247-1 cable are shown here : COM1 - DB9 PIN DEFINITIONS J8 1o 2o 3o Page 2-4 J10 1o 2o 3o U2 - Not Installed U3 - Installed U4 - Not Installed OPERATIONS MANUAL MCM/LPM-TX 1 2 3 4 5 6 7 8 9 DCD RX Data TX Data DTR GND DSR RTS CTS RI 010911 WinSystems - "The Embedded Systems Authority" 2.5.2 COM2 RS-232 COM2 is I/O mapped at 2F8H and utilizes a 16550 type UART contained in the SuperI/O chip. When used in RS-232 mode, COM2 is terminated via the multi-I/O connector at J2. The configuration details and the pin definitions, when used with the CBL-247-1 cable, are shown here : COM2 - DB9 PIN DEFINITIONS J12 J9 1o 2o 3o 2.5.3 1o 2o 3o U6 - Installed U5 - Not Installed U7 - Not Installed 1 2 3 4 5 6 7 8 9 DCD RX Data TX Data DTR GND DSR RTS CTS RI COM 1 RS-422 RS-422 signal levels are supported on both serial channels with the installation of the optional “Chip Kit” WinSystems' part number CK-75176-2. This kit provides the driver ICs necessary for a single channel of RS-422. If two channels of RS- 422 are required then two kits will be needed. RS-422 is a 4-wire point-to-point full-duplex interface allowing much longer cable runs than are possible than with RS-232. The differential transmitter and receiver twisted-pairs offer a higher degree of noise immunity. RS-422 usually requires that the lines be terminated at both ends. The following illustrations show the correct jumpering, driver IC installation, termination resistor location, and I/O connector pin definitions for each of the COM 1 channels when used in RS-422 mode. COM1 - DB9 PIN DEFINITIONS J8 J10 1o 2o 3o 1o 2o 3o U2 - Installed U3 - Not Installed U4 - Installed VCC R23 RX+ R22 RX- 1 2 3 4 5 6 7 8 9 N/A TX+ TXN/A GND RX+ RXN/A N/A RS-422 NOTE : When used in RS-422 mode, the transmitter must be enabled by setting the RTS bit in the Modem Control Register (Bit1). R14 010911 OPERATIONS MANUAL MCM/LPM-TX Page 2-5 WinSystems - "The Embedded Systems Authority" 2.5.4 COM2 RS-422 COM2 - DB9 PIN DEFINITIONS J9 J12 U5 - Installed 1o 2o 3o 1o 2o 3o U6 - Not Installed U7 - Installed VCC R30 RX+ 1 N/A 2 TX+ 3 TX4 N/A 5 GND 6 RX+ 7 RX8 N/A 9 N/A RS-422 NOTE : When used in RS-422 mode, the transmitter must be enabled by setting the RTS bit in the Modem Control Register (Bit1). R31 RXR19 Important Note : All serial termination components are surface mount 0805 packages. These should only be installed by surface mount qualified individuals. 2.5.5 RS-485 Configuration The RS-485 multi-drop interface is supported on both serial channels with the installation of the optional “Chip Kit” WinSystems' part number CK-75176-2. A single kit is sufficient to configure two of the channels for RS-485. RS-485 is a 2-wire multi-drop interface where only one station at a time talks (transmits) while all others listen (receive). RS-485 usually requires the twisted line-pair be terminated at each end of the run. The following illustrations show the correct jumpering, driver IC installation, and I/O connector pin-out for each of the channels when used in RS-485 mode. Page 2-6 OPERATIONS MANUAL MCM/LPM-TX 010911 WinSystems - "The Embedded Systems Authority" 2.5.6 COM1 RS-485 COM1 - DB9 PIN DEFINITIONS J10 J8 1o 2o 3o U2 - Installed U3 - Not Installed U4 - Not Installed 1o 2o 3o Normal RS-485 Operation is achieved by jumpering J10 pins 1-2. For RS-485 with Echo-back add jumper J8 pins 2-3 VCC R24 TX/RX+ R16 TX/RXR15 1 2 3 4 5 6 7 8 9 N/A TX+/RX+ TX-/RXN/A GND N/A N/A N/A N/A RS-485 NOTE : Because RS-485 uses a sin gle twisted- pair, all trans mit ters are connected in parallel. Only one station at a time may transmit or have its transmitter enabled. The transmitter Enable/Disable is controlled in software using bit 1 in the Modem Control Register (RTS). When RTS is set, the transmitter is enabled, and when cleared (the normal state) the transmitter is disabled and the receiver is enabled. Note that it is necessary to allow some minimal settling time after enabling the transmitter before transmitting the first character. Likewise, following a transmission, it is necessary to be sure that all characters have been completely shifted out of the UART (Check Bit 6 in the Line Status Register) before disabling the transmitter to avoid chopping off the last character. Important Note : All serial termination components are surface mount 0805 packages. These should only be installed by surface mount qualified individuals. 010911 OPERATIONS MANUAL MCM/LPM-TX Page 2-7 WinSystems - "The Embedded Systems Authority" COM2 RS-485 2.5.7 COM2 - DB9 PIN DEFINITIONS J12 J9 1o 2o 3o U5 U6 U7 1o 2o 3o - Installed - Not Installed - Not Installed Normal RS-485 Operation is achieved by jumpering J12 pins 1-2 For RS-485 with Echo-back add jumper J9 pins 2-3 VCC R29 TX/RX+ R17 TX/RXR18 1 2 3 4 5 6 7 8 9 N/A TX+/RX+ TX-/RXN/A GND N/A N/A N/A N/A RS-485 NOTE : Because RS-485 uses a sin gle twisted- pair, all trans mit ters are connected in parallel. Only one station at a time may transmit or have its transmitter enabled. The transmitter Enable/Disable is controlled in software using bit 1 in the Modem Control Register (RTS). When RTS is set, the transmitter is enabled, and when cleared (the normal state) the transmitter is disabled and the receiver is enabled. Note that it is necessary to allow some minimal settling time after enabling the transmitter before transmitting the first character. Likewise, following a transmission, it is necessary to be sure that all characters have been completely shifted out of the UART (Check Bit 6 in the Line Status Register) before disabling the transmitter to avoid chopping off the last character. Important Note : All serial termination components are surface mount 0805 packages. These should only be installed by surface mount qualified individuals. Page 2-8 OPERATIONS MANUAL MCM/LPM-TX 010911 WinSystems - "The Embedded Systems Authority" J1708 Configuration 2.5.8 The Society of Automotive Engineers (SAE) J1708 interface is a variation of the RS-485 interface which is used for “Serial Data Communications between Microcomputer Systems in Heavy Duty Vehicle Applications”. It is beyond the scope of this document to go into detail on the J1708 specification. The MCM/LPM-TX may be user configured for J1708 by the addition of the CK-75176-2 “Chip Kit”. One “Chip Kit” is sufficient to configure both channels for J1708. The illustrations that follow show the correct jumpering, driver IC installation, I/O connector pin definitions, and the optional, user installed, termination network details for each of the channels when used in J1708 mode. COM1 J1708 2.5.9 COM1 DB9 J8 J10 1o 2o 3o 1o 2o 3o U2 - Installed U3 - Not Installed U4 - Not Installed 1 2 3 4 5 6 7 8 9 N/A TX+/RX+ TX-/RXN/A GND N/A N/A N/A N/A VCC R24 4.7K R25 470 OHM TX/RX+ R16 Absent R15 4.7K C36 .0022 ufd C39 .0022 ufd TX/RX- R26 470 OHM Important Note : All serial termination components are surface mount 0805 packages. These should only be installed by surface mount qualified individuals. 010911 OPERATIONS MANUAL MCM/LPM-TX Page 2-9 WinSystems - "The Embedded Systems Authority" COM2 J1708 2.5.10 COM2 DB9 J9 1o 2o 3o J12 1o 2o 3o 1 2 3 4 5 6 7 8 9 U5 - Installed U6 - Not Installed U7 - Not Installed N/A TX+/RX+ TX-/RXN/A GND N/A N/A N/A N/A VCC R29 4.7K R27 470 OHM TX/RX+ R17 Absent R16 4.7K 2.6 C38 .0022 ufd C39 .0022 ufd TX/RX- R28 470 OHM Watchdog Timer J20 1o 2o 3o The MCM/LPM-TX features a power-on voltage detect and power-down/power brownout reset circuit to protect memory and I/O from faulty CPU operation during periods of illegal voltage levels. The supervisor circuitry also features a watchdog timer which can be used to guard against software lockups. An internal timer with a period of 1.5 seconds will, when enabled, reset the CPU if the watchdog has not been serviced within the allotted time. There are three watchdog modes available on the MCM/LPM-TX. With no jumper installed on J20, the watchdog is totally disabled and can never reset the CPU. When J20 is jumpered pins 2-3, the watchdog circuit is permanently enabled and timing begins Page 2-10 OPERATIONS MANUAL MCM/LPM-TX 010911 WinSystems - "The Embedded Systems Authority" immediately with power on. This mode NOT compatible with the Award BIOS or with MSDOS but is available for directly embedded code that takes place of the BIOS. The watchdog must be accessed every 1.5 seconds or a reset will occur. Petting in this mode is accomplished by writing to I/O port 1EFH with any value. An alternate mode of operation is via software enable/disable control. This mode is set by jumpering J20 pins 1-2. In this mode the watchdog timer powers up disabled and must be enabled in software before timing will begin. Enabling is accomplished by writing a 1 to I/O port 1EEH. Writing a 0 to I/O port 1EEH will disable the watchdog. After enabling, petting may be accomplished by writing any value to port 1EFH at least every 1.5 seconds or a reset will occur. This mode of operation can be used with the BIOS or DOS provided that the watchdog is disabled before making any extensive BIOS or DOS calls, especially video or Disk I/O calls which could exceed the 1.5 seconds allowed. The drawback to this mode is that a lockup during the time the watchdog is disabled will not allow for autorecovery and will require an external reset. 2.7 Battery Select Control J22 1o 2o 3o Battery jumper J22 An onboard 350mAh nominal capacity, lithium battery is provided for the CMOS Clock/Calendar. A master battery enable jumper is provided at J22. When J22 is jumpered pins 2-3, battery power is supplied to the Clock/Calendar. When J22 is jumpered pins 1-2, the battery is totally disconnected and no current will be drawn from it. Battery life is highly dependent upon duty cycle as there is no current drawn from the battery when +5 volts is applied to the board. Both storage and operational temperatures play a prominent factor in battery life. High temperatures will shorten battery life significantly. J22 must be jumpered 1-2 if a battery is not installed. 010911 OPERATIONS MANUAL MCM/LPM-TX Page 2-11 WinSystems - "The Embedded Systems Authority" STD-Bus Interface 2.8 J23 J24 1o 2o 1oo2 3oo4 5oo6 STD-Bus V-Bat Enable STD-Bus Configuration Jumper J24 The MCM/LPM-TX is compatible with the STD-8088/188 bus specification. Vendor specific implementation information is provided below. PIN 35 *IOEXP is driven low for I/O access in the 100-1FFH I/O address range. This allows I/O cards supporting IOEXP but only decoding 8 address lines to be safely qualified into a known 256 address predecoded block. PIN 39 When J24 pins 1-3 (Factory default) are jumpered STD- BUS pin 39 acts as the *MEMCS16 signal used for dynamic 8-bit/16-bit bus sizing per the P16 STD-BUS standard practice for 16-bit memory accessing. When J24 pins 3-5 are jumpered together, STD-BUS pin 39 assumes a pseudo *STATUS1 usage. Some STD-BUS vendor cards use the STATUS1 signal in place of the *WR line for decoding purposes. When jumpered in this position the *WR signal is gated onto PIN 39 allowing these cards to function. PIN 40 When J24 pins 2-4 (factory default) are jumpered STD- BUS pin 40 acts as the *IOCS16 signal used for dynamic 8-bit/16- bit bus sizing per the STD-BUS standard practice for 16-Bit I/O accessing. When J24 pins 4-6 are jumpered together. STD-BUS pin 40 assumes a pseudo *STATUS0 usage. Some STD-BUS vendor cards use the *STATUS0 signal in place of the *RD line in their decoding. When jumpered in this position the *RD signal is gated onto pin 40 to allow usage of these cards. 2.8.1 STD-Bus V-Bat Enable The STD-Bus V-bat enable jumper is located at J23. When J23 is jumpered, battery voltage is routed to pin 5 of the STD-Bus. When open, J23 isolates battery voltage to the backplane. An example of both is shown here : J23 J23 1o 2o Page 2-12 STD V-Bat Enabled 1o 2o OPERATIONS MANUAL MCM/LPM-TX STD V-Bat Disabled 010911 WinSystems - "The Embedded Systems Authority" 2.9 DiskOnChip Configuration J11 1oo2 3oo4 Silicon Disk Configuration Jumpers J11 and J21 J21 1o 2o The MCM/LPM-TX supports the use of M-Systems’ DiskOnChip (DOC) device to be used as a Solid State Disk (SSD) drive. This section documents the required hardware configurations for the DOC devices. The 32-pin JEDEC memory socket at U8 is used to contain the DOC devices used for the disk. The silicon disk array is memory mapped into a 32Kbyte hole at segment D000 or D800. The DiskOnChip can be enabled by jumpering J11 and J21 as shown below : J21 J21 1o 2o 1o 2o DiskOnChip Enable DiskOnChip Disable J11 J11 2oo1 4oo3 2oo1 4oo3 DOC at D800:0000 DOC at D000:0000 Note : J11 (1-2) is BIOS write, and must be jumpered (1-2) at all times for proper PnP operation. 010911 OPERATIONS MANUAL MCM/LPM-TX Page 2-13 WinSystems - "The Embedded Systems Authority" 2.10 Multi I/O Connector The I/O to the primary serial channels, the printer port, and keyboard are all terminated via the connector at J2. An adapter cable, part number CBL-247-1, is available from WinSystems to adapt to the conventional I/O connectors. The pin definitions for J2 are shown here : J2 COM1 - DCD COM1 - RXD COM1 - TXD COM1 - DTR COM1 - GND COM2 - DSR COM2 - RTS COM2 - CTS COM2 - RI LPT - STROBE LPT - PD0 LPT - PD1 LPT - PD2 LPT - PD3 LPT - PD4 LPT - PD5 LPT - PD6 LPT - PD7 LPT - ACK LPT - BUSY LPT - PE LPT - SLCT KEYBD - GND KEYBD - KDATA KEYBD - +5V 2.11 1o 3o 5o 7o 9o 11 o 13 o 15 o 17 o 19 o 21 o 23 o 25 o 27 o 29 o 31 o 33 o 35 o 37 o 39 o 41 o 43 o 45 o 47 o 49 o o2 o4 o6 o8 o 10 o 12 o 14 o 16 o 18 o 20 o 22 o 24 o 26 o 28 o 30 o 32 o 34 o 36 o 38 o 40 o 42 o 44 o 46 o 48 o 50 COM1 - DSR COM1 - RTS COM1 - CTS COM1 - RI COM2 - DCD COM2 - RXD COM2 - TXD COM2 - DTR COM2 - GND LPT - AUTOFD LPT - ERROR LPT - INIT LPT - SLCTIN LPT - GND LPT - GND LPT - GND LPT - GND LPT - GND LPT - GND LPT - GND LPT - GND KEYBD - GND KEYBD - GND KEYBD - CLK KEYBD - +5V USB Connector A USB cable may be attached via the connector at J1. An adapter cable, CBL-249-1 is available from WinSystems to adapt to a conventional USB Port. The pinout for J1 is shown here for reference : J1 1o 2o 3o 4o Page 2-14 USBV0 D0D0+ USBG0 OPERATIONS MANUAL MCM/LPM-TX 010911 WinSystems - "The Embedded Systems Authority" 2.12 PC/104 Bus Interface The MCM/LPM-TX supports I/O expansion through the standard PC/104 connectors at J27. The MCM/LPM-TX supports both 8-bit and 16-bit PC/104 modules. The PC/104 connector pin definitions are provided here for reference purposes : J27 GND MEMCS16 IOCS16 IRQ10 IRQ11 IRQ12 IRQ15 IRQ14 DACK0 DRQ0 DACK5 DRQ5 DACK6 DRQ6 DACK7 DRQ7 VCC MASTER GND GND 010911 D0 o D1 o D2 o D3 o D4 o D5 o D6 o D7 o D8 o D9 o D10 o D11 o D12 o D13 o D14 o D15 o D16 o D17 o D18 o D19 o o o o o o o o o o o o o o o o o o o o o C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 C10 C11 C12 C13 C14 C15 C16 C17 C18 C19 GND SBHE LA23 LA22 LA21 LA20 LA19 LA18 LA17 MEMR MEMW SD8 SD9 SD10 SD11 SD12 SD13 SD14 SD15 KEY IOCHK BD7 BD6 BD5 BD4 BD3 BD2 BD1 BD0 IOCHRDY AEN SA19 SA18 SA17 SA16 SA15 SA14 SA13 SA12 SA11 SA10 SA9 SA8 SA7 SA6 SA5 SA4 SA3 SA2 SA1 SA0 GND A1 o A2 o A3 o A4 o A5 o A6 o A7 o A8 o A9 o A10 o A11 o A12 o A13 o A14 o A15 o A16 o A17 o A18 o A19 o A20 o A21 o A22 o A23 o A24 o A25 o A26 o A27 o A28 o A29 o A30 o A31 o A32 o OPERATIONS MANUAL MCM/LPM-TX o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o B1 B2 B3 B4 B5 B6 B7 B8 B9 B10 B11 B12 B13 B14 B15 B16 B17 B18 B19 B20 B21 B22 B23 B24 B25 B26 B27 B28 B29 B30 B31 B32 GND RESET +5V IRQ9 -5V DRQ2 -12V 0WS +12V GND MEMW MEMR IOW IOR DACK3 DRQ3 DACK1 DRQ1 REFRESH SYSCLK IRQ7 IRQ6 IRQ5 IRQ4 IRQ3 DACK2 TC BALE +5V OSC GND GND Page 2-15 WinSystems - "The Embedded Systems Authority" 2.13 PC/104-Plus Bus Interface J16 is the PC/104-Plus bus connector. The pin definitions for this connector are shown here for reference : Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 Page 2-16 A GND/5.0 KEY VI/O AD05 C/BE0* GND AD11 AD14 +3.3V SERR* GND STOP* +3.3V FRAME* GND AD18 AD21 +3.3V IDSEL0 AD24 GND AD29 +5V REQ0* GND GNT1* +5V CLK2 GND +12V -12V J16 B Reserved AD02 GND AD07 AD09 VI/O AD13 C/BE1* GND PERR* +3.3V TRDY* GND AD16 +3.3V AD20 AD23 GND C/BE3* AD26 +5V AD30 GND REQ2* VI/O CLK0 +5V INTD* INTA* Reserved C +5 AD01 AD04 GND AD08 AD10 GND AD15 SB0* +3.3V LOCK* GND IRDY* +3.3.V AD17 GND AD22 IDSEL1 VI/O AD25 AD28 GND REQ1* +5V GNT2* GND CLK3 +5V INTB* Reserved OPERATIONS MANUAL MCM/LPM-TX D AD00 +5V AD03 AD06 GND M66EN AD06 +3.3V PAR SDONE GND DEVSEL* +3.3V C/BE3* GND AD19 +3.3V IDSEL2 IDSEL3 GND AD27 AD31 VI/O GNT0* GND CLK1 GND RST* INTC* GND/3.3V KEY 010911 WinSystems - "The Embedded Systems Authority" 2.14 IDE Interface The MCM/LPM-TX supports standard IDE fixed disks through the I/O connector at J7 . A red activity LED is present at D1. The pin definitions J7 are shown here for reference : J7 RST D7 D6 D5 D4 D3 D2 D1 D0 LED DRQ IOW IOR RDY DACK IRQ A1 A0 CS1 VCC 2.15 1 o 3 o 5 o 7 o 9 o 11 o 13 o 15 o 17 o 19 o 21 o 23 o 25 o 27 o 29 o 31 o 33 o 35 o 37 o 39 o o 2 o 4 o 6 o 8 o 10 o 12 o 14 o 16 o 18 o 20 o 22 o 24 o 26 o 28 o 30 o 32 o 34 o 36 o 38 o 40 GND D8 D9 D10 D11 D12 D13 D14 D15 N/C GND GND GND NC GND NC NC A2 CS3 GND Floppy Interface The MCM/LPM-TX supports up to 2 standard 3 1/2" or 5 1/4" PC compatible floppy disk drives. The drives are connected via the I/O connector at J6. Note that the interconnect cable to the drives is a standard floppy I/O cable used on desk-top PCs. The cable must have the twisted section prior to the drive A position. The pin definitions for the J6 connector are shown here : GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND 010911 J6 1 o o 3 o o 5 o o 7 o o 9 o o 11 o o 13 o o 15 o o 17 o o 19 o o 21 o o 23 o o 25 o o 27 o o 29 o o 31 o o 33 o o 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 RPM/LC N/C N/C INDEX MTR0 DRV1 DRV0 MTR1 DIR STEP WDATA WGATE TRK0 WPRT RDATA HDSEL DSKCHG OPERATIONS MANUAL MCM/LPM-TX Page 2-17 WinSystems - "The Embedded Systems Authority" Mouse Connector 2.16 J3 J5 123 ooo 12345 ooooo CPU Fan Connector J3 PS 2 Mouse Connector J5 A PS/2 mouse may be attached via the connector at J5. An adapter cable, CBL-225-1 is available from WinSystems to adapt to a conventional PS/2 mouse connector. The pinout for J2 is shown here for reference : J5 1o 2o 3o 4o 5o 2.17 MSDATA N/C GND VCC MSCLK CPU Fan Connector The MCM/LPM-TX has a connector located at J3 to supply power to the processor cooling fan. The pin definitions are shown here for reference. J3 1o 2o 3o Page 2-18 GND +5V N/C OPERATIONS MANUAL MCM/LPM-TX 010911 WinSystems - "The Embedded Systems Authority" 2.18 Parallel Printer Port Multi-I/O connector J2 The MCM/LPM-TX supports a fully bi-directional parallel printer port capable of EPP and ECP operations. The PnP parallel port is mapped at 378H and is terminated at the Multi-I/O connectors at J2 (pinout shown on page 2-14). The pin definitions for the parallel port DB25 connector when using the CBL-247-1 cable are shown below: J2 STROBE PD0 PD1 PD2 PD3 PD4 PD5 PD6 PD7 ACK BUSY PE SLCT 2.19 1o 2o 3o 4o 5o 6o 7o 8o 9o 10 o 11 o 12 o 13 o o 14 o 15 o 16 o 17 o 18 o 19 o 20 o 21 o 22 o 23 o 24 o 25 AUTOFD ERROR INIT SLIN GND GND GND GND GND GND GND GND Status LED A green LED is populated on the board at D2 which can be used for any application specific purpose. The LED can be turned on in software by writing a 1 to I/O port 1EDH. The LED can be turned off by writing a 0 to 1EDH. 010911 OPERATIONS MANUAL MCM/LPM-TX Page 2-19 WinSystems - "The Embedded Systems Authority" 2.20 Jumper/Connector Summary Jumper/ Connector J1 J2 J3 J4 J5 J6 J7 J8 J9 J10 J11 J12 J13 J14 J15 J16 J19 J20 J21 J22 J23 J24 J25 J27 Page 2-20 Description Page Number USB Connector Multi I/O Connector CPU Fan Connector Over The Top Interrupt Connector PS2 Mouse Connector Floppy Connector IDE Connector COM1 Configuration COM2 Configuration COM1 Configuration Silicon Disk Configuration COM2 Configuration CPU Speed Select CPU Speed Select CPU Speed Select PC/104-Plus Connector Interrupt Routing Header Watchdog Enable Silicon Disk Enable Battery Enable STD-Bus V-Bat Enable STD-Bus pins 39 and 40 STD-Bus Connector PC/104 Connector 2-14 2-14 2-18 2-3 2-18 2-17 2-17 2-4 2-5 2-4 2-13 2-5 2-2 2-2 2-2 2-16 2-3 2-10 2-13 2-11 2-12 2-12 N/A 2-15 OPERATIONS MANUAL MCM/LPM-TX 010911 3 Award BIOS Configuration 3.1 General Information The MCM/LPM-TX comes equipped with a standard Award BIOS with Setup in ROM that allows users to modify the basic system configuration. This type of information is stored in battery-backed CMOS RAM so that it retains Setup information when power is turned off. 3.2 Entering Setup To enter setup, power on the computer and press the DEL key immediately after the message “Press DEL to Enter Setup” appears on the lower left of the screen. If the message disappears before you respond and you still wish to enter setup, restart the system by turning it OFF and then ON or by pressing the RESET button, if so equipped, or by pressing the CTRL, ALT and DEL key simultaneously. Alternately, under certain error conditions of incorrect setup the message: “Press F1 to continue or DEL to Enter Setup” may appear. To Enter Setup at that time press the DEL key. To attempt to continue, ignoring the error condition, press the F1 key. 3.3 Setup Main Menu The main menu screen is displayed on the following page. Each of the options will be discussed in this section. Use the arrow keys to highlight the desired selection and press ENTER to enter the sub-menu or to execute the function selected. 010911 OPERATIONS MANUAL MCM/LPM-TX Page 3-1 WinSystems - "The Embedded Systems Authority" ROM PCI/ISA BIOS (2A59IA2N) CMOS SETUP UTILITY Award SOFTWARE, INC. STANDARD CMOS SETUP BIOS FEATURES SETUP CHIPSET FEATURES SETUP PnP/PCI CONFIGURATION LOAD BIOS DEFAULTS LOAD SETUP DEFAULTS INTEGRATED PERIPHERALS SUPERVISOR PASSWORD USER PASSWORD IDE HDD AUTO DETECTION SAVE AND EXIT SETUP EXIT WITHOUT SAVING ↑↓→← :Select Item (Shift) F2 : Change Color Esc : Quit F10 : Save & Exit Setup Time, Date. Hard Disk, Type... 3.4 Standard CMOS Setup The items in the Standard CMOS Setup menu are divided into several categories. Each category may include one or more setup items. Use the arrow keys to highlight the item and then use the PgUp, PgDn, +.-. keys to select the desired value for the item. Date The date format is <day>,< date>,< month>, <year> day = The day, from Sun to Sat, determined by the BIOS and is display only Date = the date, from 1 to 31 (or the maximum for the current month) month = the month, JAN through DEC year = The year, from 1900 to 2099 Time The time is hour, minute, second. The time is calculated on the 24-hour, military-time clock such that 1:00PM is 13:00:00. Page 3-2 OPERATIONS MANUAL MCM/LPM-TX 010911 WinSystems - "The Embedded Systems Authority" ROM PCI/ISA BIOS (2A59IA2N) STANDARD CMOS SETUP Award SOFTWARE, INC. Date (mm:dd:yy) : Wed, Sep 25 2000 Time (hh:mm:ss): 13 : 28 : 46 HARD DISKS Primary Master Primary Slave Secondary Master Secondary Slave : : : : TYPE SIZE Auto Auto Auto Auto 0 0 0 0 CYLS 0 0 0 0 Drive A : 1.44M, 3.5 in Drive B: None Floppy Mode 3 Support : Disabled Video : EGA/VGA Halt On : No Errors HEAD PRECOMP LANDZ SECTOR MODE 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 AUTO AUTO AUTO AUTO Base Memory : 640K Extended Memory : 31744K Other Memory : 384K Total Memory: 32768K ESC : Quit F1 : Help : Select Item (Shift) F2 : Change Color PU/PD/+/- : Modify Drive C / Drive D type This category identifies the type of hard disk C: or hard disk D: that has been installed in the system. There are 46 predefined types and a user definable type. Types 1-46 are shown in the following table. Type 1 2 3 4 5 6 7 8 9 010911 Size 10 20 30 62 46 20 30 30 112 Cylinders 306 615 615 940 940 615 462 733 900 Heads 4 4 6 8 6 4 8 5 15 Sectors 17 17 17 17 17 17 17 17 17 OPERATIONS MANUAL MCM/LPM-TX Precomp 128 300 300 512 512 None 256 None None Landzone 305 615 614 940 940 615 511 733 901 Page 3-3 WinSystems - "The Embedded Systems Authority" 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 20 35 49 20 42 20 40 56 59 30 42 30 10 40 76 71 111 152 68 93 83 69 85 102 110 119 17 136 114 40 42 65 40 61 100 203 820 855 855 306 733 Reserved 612 977 977 1024 733 733 306 977 1024 1224 1224 1224 1024 1024 918 925 1024 1024 1024 1024 1024 1024 1024 918 820 1024 1024 809 809 776 684 3 5 7 8 7 17 17 17 17 17 None None None 128 None 820 855 855 319 733 4 5 7 7 5 7 5 4 5 9 7 11 15 8 11 11 9 10 12 13 14 2 16 15 6 5 5 6 6 8 16 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 26 17 26 33 38 0 300 None 512 300 300 300 0 None None None None None None None None None None None None None None None None None None None None None None None 663 977 977 1023 732 732 733 336 976 1023 1223 1223 1223 1023 1023 1023 926 1023 1023 1023 1023 1023 1023 1023 820 1023 1023 852 852 775 685 Press PgUp or PgDn to select a numbered hard disk type, or type the number and press ENTER. Most manufacturers supply type information with their drives that can be used to help identify the proper drive type. Modern IDE drives seldom fall into the predefined types and are usually best handled with the “auto” or “user” types. The “auto” mode, reads the hard disk type information from the drive at boot time and uses it to access the drive. The “user” mode allows for either manual or automatic entry, via the setup option “IDE Auto Detect” of the drive parameters. Page 3-4 OPERATIONS MANUAL MCM/LPM-TX 010911 WinSystems - "The Embedded Systems Authority" If you decide to create the user type manually, you must supply the required parameters as to Cylinder count, Head count, Precomp Cylinder, Landing Zone Cylinder, and number of sectors per track. On Hard disks larger than 528MB, it will be necessary to choose the Logical Block Addressing mode (LBA) if you wish the drive to be accessible as a single drive letter. If there is not hard disk installed, be sure to select “None”. Drive A type/Drive B type This category identifies the type of floppy drives attached as Drive A: or Drive B:. The choices are as follows : NONE 360K, 5.25 in. 1.2M, 5.25 in. 720K, 3.5 in 1.44M, 3.5 in. Video This category specifies the type of video adapter used for the primary system monitor that matches your video display board and monitor. The available choices are: EGA/VGA CGA40 CGA80 MONO The MCM/LPM-TX has built-in VGA support so EGA/VGA should be selected. Error Halt This category determines whether the system will halt if a non-fatal error is detected during the power-up self test. The choices are: No Errors : The system will not be stopped for any error that may be detected. All Errors : Whenever the BIOS detects a non-fatal error, the system will be stopped and a prompt will appear. All, but Keyboard : The system will not stop for a keyboard error, it will stop for all other errors. All, but diskette : The system will not stop for disk errors. All others will result in a prompt. All but Disk/Key : All errors except diskette or keyboard will result in a halt and a prompt. 010911 OPERATIONS MANUAL MCM/LPM-TX Page 3-5 WinSystems - "The Embedded Systems Authority" Memory This category is display only and is determined by the BIOS POST (Power-On Self Test). Base Memory The POST routines in the BIOS will determine the amount of base (conventional) memory installed in the system. The value of the base memory is typically 640K for systems with a Megabyte of memory or greater. Extended Memory The BIOS determines how much extended memory is present during the POST. This is the amount of memory located above 1MB in the CPU's memory address space. Other Memory This refers to memory located in the 640K to 1024K address space. This is memory that can be used for different applications. DOS may use this area to load device drivers and TSRs to keep as much base memory free as possible for application programs. The most common use of this area is for shadow RAM. Page 3-6 OPERATIONS MANUAL MCM/LPM-TX 010911 WinSystems - "The Embedded Systems Authority" ROM PCI/ISA BIOS (2A59IA2N) BIOS FEATURES SETUP Award SOFTWARE, INC. Virus Warning : Disabled CPU Internal Cache : Enabled External Cache : Enabled Quick Power On Self Test : Enabled Boot Sequence : A,C,SCSI Swap Floppy Drive : Disabled Boot Up Floppy Seek : Disabled Boot Up NumLock Status : On Boot Up System Speed : High Gate A20 Option : Fast Typematic Rate Setting : Disabled Typematic Rate (Chars/Sec) : 6 Typematic Delay (Msec) : 250 Security Option : Setup PCI/VGA Palette Snoop : Disabled Assign IRQ For VGA : Disabled OS Select For DRAM>64MB : Non-OS2 Report No FDD For Win 95 : Yes 3.5 Video BIOS Shadow C8000-CBFFF Shadow CC000-CFFFF Shadow D0000-D3FFF Shadow D4000-D7FFF Shadow D8000-DBFFF Shadow DC000-DFFFF Shadow : Enabled : Disabled : Disabled : Disabled : Disabled : Disabled : Disabled ESC : Quit ↑ ↓ → ← : Select Item F1 : Help PU/PD/+/- : Modify F5 : Old Value Shift F2 : Color F6 : Load BIOS Defaults F7 : Load Setup Defaults BIOS Features Setup Virus Warning This option when enabled, protects the boot sector and partition table of the hard disk against unauthorized writes through the BIOS. Any attempt to alter these areas will result in an error message and a prompt to authorize the activity. CPU Internal Cache This option, when enabled, provides maximum performance by caching instructions and data using the on-chip cache of the Pentium or K6 processor. External Cache This option, when enabled, further enhances performance by caching recently used instructions and data into fast SRAM. 010911 OPERATIONS MANUAL MCM/LPM-TX Page 3-7 WinSystems - "The Embedded Systems Authority" Quick Power On Self Test (POST) This option, when enabled, speeds up the POST during power up. If it is enabled, the BIOS will shorten and/or skip some items during POST. Boot Sequence This option determines the boot attempt sequence for the fixed disk and floppy disk. If there is no media available at first drive choice, system automatically moves to next drive in list. The choices are: C, A A, C A, C, SCSI C, A, SCSI C, CD ROM, A D, A, SCSI E, A, SCSI F, A, SCSI SCSI, A, C SCSI, C, A C ONLY LS120, C Swap Floppy Drive This option allows for swapping of the A: and B: floppy drives without actually relocating the drives on the cable. Boot Up Floppy Seek During POST, when this option is enabled, the BIOS will determine if the floppy drive is 40 tracks or 80 tracks. If disabled, no seek test will be performed and no error can be reported. Boot Up Numlock Status This allows user selection of the Numlock state at boot time. Boot Up System Speed This option allows specification of the processor speed at boot time. The options are: HIGH LOW Page 3-8 OPERATIONS MANUAL MCM/LPM-TX 010911 WinSystems - "The Embedded Systems Authority" Gate A20 Option This option allows for the selection of the source for the gate A20 signal. The choices are: Normal - Sourced from the keyboard controller Fast - Sourced from the Chipset Typematic Rate Setting This option enables or disables the typematic rate programming at boot time. Typematic is the auto-repeat function for the keyboard. Typematic Rate When the typematic rate setting is enabled the typematic repeat speed is set via this option. The supported rates are : 6 characters per second 8 characters per second 10 characters per second 12 characters per second 15 characters per second 20 characters per second 24 characters per second 30 characters per second Typematic Delay When typematic rate setting is enabled, this option specifies the time in milliseconds before auto-repeat begins. The supported values are: 250 mS 500 mS 750 mS 1000 mS Security Option This option allows you to limit access to the system and setup, or just to setup. The choices are: System - The system will not boot and access will be denied if the correct password is not entered at the prompt. Setup - The system will boot, but access to Setup will be denied if the correct password is not entered at the prompt. 010911 OPERATIONS MANUAL MCM/LPM-TX Page 3-9 WinSystems - "The Embedded Systems Authority" NOTE: To disable security, select “Password Setting” at the Setup Main Menu and then you will be asked to enter a password. Do not type anything, just hit ENTER. Once the security is disabled, the system will boot and you can enter Setup freely. PCI/VGA Palette Snoop This option allows for enabling or disabling of the PCI/VGA Palette snoop. Assign IRQ for VGA This option, when enabled, assigns an IRQ to the video adapter. OS Select for DRAM > 64MB This option allows selection of an operating system for DRAM greater than 64MB. The options are: OS2 Non-OS2 Report No FDD for Win 95 This option, when enabled, signals Windows 95 if there is no floppy present. The options are: Yes No Shadowing Options When shadowing for a particular address range is enabled, it instructs the BIOS to copy the BIOS located in ROM into DRAM. This shadowing from an 8-bit EPROM into fast 32bit DRAM results in a Multi-magnitude increase in performance. The main BIOS is shadowed automatically but there are other areas that may be selected for shadowing as shown here: Video BIOS Shadow - C000-C7FFF EGA/VGA BIOS ROM C8000-CBFFF CC000-CFFFF D0000-D3FFF D4000-D7FFF D8000-DBFFF DC000-DFFFF Page 3-10 OPERATIONS MANUAL MCM/LPM-TX 010911 WinSystems - "The Embedded Systems Authority" ROM PCI/ISA BIOS (2A59IA2N) CHIPSET FEATURES SETUP Award SOFTWARE, INC. Auto Configuration : Enabled DRAM Timing LEAD Off Timing DRAM Read Burst DRAM Write Burst Timing FAST EDO lead off Refresh RAS# Assertion Fast RAS to CAS Delay DRAM Page Idle Timer DRAM Enhanced Paging Fast MA to RAS# Delay SDRAM (CAS Lat/RAS-to-CAS) System BIOS Cacheable Video BIOS Cacheable 8 Bit I/O Reovery Time 16 Bit I/O Recovery Time Memory HoleAt 15M-16M PCI 2.1 Compliance : 70ns : 10/6/4 : x333/x444 : x333 : Disabled : 5 Clks :3 : 2 Clks : Enabled : 2 Clks : 3/3 : Disabled : Disabled :1 :2 : Disabled : Disabled 3.6 ESC : Quit ↑ ↓ → ← : Select Item F1 : Help PU/PD/+/- : Modify F5 : Old Value Shift) F2 : Color F6 : Load BIOS Defaults F7 : Load Setup Defaults Chipset Features Setup The options in this section control the chipset programming at boot time. In most cases, the default settings should be used unless you have a clear understanding of the significance of the change. It is possible using these options to create a system that will either not boot or is very unstable or unreliable. If this should occur, there are two methods to return the system to a stable configuration. If the system works well enough to get into Setup, simply choose the “Load BIOS Defaults” option and then select “Save and Exit Setup” to restore factory defaults. If the system will not run well enough to run Setup, it will be necessary to remove the battery source temporarily until the CMOS memory decays. Refer to Section 2.19 for details on reinitializing the CMOS RAM. 010911 OPERATIONS MANUAL MCM/LPM-TX Page 3-11 WinSystems - "The Embedded Systems Authority" Each of the options for the Chipset Features Menu will be briefly discussed in the sections that follow. Auto Configuration This option, when enabled, instructs the BIOS to auto-select the proper DRAM timing, lead Off timing, DRAM read burst, DRAM write burst timing, Fast EDO lead off, Refresh RAS # Assertion, Fast RAS to CAS Delay, DRAM Page Idle Timer, DRAM Enhanced Paging, Fast MA to RAS# Delay, SDRAM (CAS Lat/RAS-to-CAS) upon the calculated CPU speed. The default is “Enabled”. System BIOS Cacheable This option enables or disables cacheability of the system BIOS. Video BIOS Cacheable This option enables or disables cacheability of the video BIOS. 8 Bit I/O Recovery Enables and defines 8-bit I/O recovery time in number of clocks. 16 Bit I/O Recovery Enables and defines 16-bit I/O recovery time in number of clocks. Memory Hole At 15M-16M Memory Hole, when enabled, disables onboard memory in the specified range. PCI 2.1 Compliance This option, when enabled, makes the MCM/LPM-TX PCI 2.1 compliant. The options are: Enabled Disabled Page 3-12 OPERATIONS MANUAL MCM/LPM-TX 010911 WinSystems - "The Embedded Systems Authority" ROM PCI/ISA BIOS (2A59IA2N) POWER MANAGEMENT SETUP Award SOFTWARE, INC. ACPI Function Power Management PM Control by APM Video Off Method Video Off After MODEM Use IRQ Doze Mode Standby Mode Suspend Mode HDD Power Down Throttle Duty Cycle ZZ Active in Suspend PCI/VGA Act-Monitor Soft-Off by PWR-BTTN CPUFAN Off In Suspend PowerOn by Ring Resume by Alarm IRQ 8 Break Suspend 3.7 : Enabled : Disabled : No : Blank Screen : NA : NA : Disabled : Disabled : Disabled : Disabled : 12.5% : Disabled : Disabled : Instant-Off : Disabled : Disabled : Disabled : Disabled ** Reload Global Timer Events ** IRQ [3-7, 9-15] ,NMI : Disabled Primary IDE 0 : Disabled Primary IDE 1 : Disabled Secondary IDE 0 : Disabled Secondary IDE 1 : Disabled Floppy Disk : Disabled Serial Port : Disabled Parallel Port : Disabled ↑ ↓ → ← : Select Item ESC : Quit F1 : Help PU/PD/+/- : Modify F5 : Old Value Shift) F2 : Color F6 : Load BIOS Defaults F7 : Load Setup Defaults Power Management ACPI Function This option enables the advanced configuration and power interface. Power Management This option, enables advance power management on the MCM/LPM-TX. PM Control by APM This option allows power management control throughout the advanced power management software interface. 010911 OPERATIONS MANUAL MCM/LPM-TX Page 3-13 WinSystems - "The Embedded Systems Authority" Video Off Method There are 3 video off methods to select from when power management is enabled. The options are: Blank Screen V/H Sync + Blank DPMS Video Off After This option, when Doze mode is enabled, will shut off video using one of the following methods: NA Suspend Standby Doze MODEM Use IRQ This option allows selection of the interrupt to use for wake-up on modem activity. The interrupt choices are: NA 3 4 5 7 9 10 11 Page 3-14 OPERATIONS MANUAL MCM/LPM-TX 010911 WinSystems - "The Embedded Systems Authority" Doze Mode This option, when power management is enabled, allows the user to select the length of time the system will wait with no activity before entering Doze mode. The choices are: Disabled 1 minute 2 minutes 4 minutes 8 minutes 12 minutes 20 minutes 30 minutes 40 minutes 1 hour Standby Mode This option, when power management is enabled, allows the user to select the length of time the system will wait with no activity before entering Standby mode. The choices are: Disabled 1 minute 2 minutes 4 minutes 8 minutes 12 minutes 20 minutes 30 minutes 40 minutes 1 hour Suspend Mode This option, when power management is enabled, allows the user to select the length of time the system will wait with no activity before entering Suspended mode. The choices are: Disabled 1 minute 2 minutes 4 minutes 8 minutes 12 minutes 20 minutes 30 minutes 40 minutes 1 hour 010911 OPERATIONS MANUAL MCM/LPM-TX Page 3-15 WinSystems - "The Embedded Systems Authority" HDD Power Down This option, when power management is enabled, allows the user to select the length of time the system will wait with no activity before entering hard disk power down mode. The choices are: 1 minute 2 minutes 3 minutes 4 minutes 5 minutes 6 minutes 7 minutes 8 minutes 9 minutes 10 minutes 11 minutes 12 minutes 13 minutes 14 minutes 15 minutes Throttle Duty Cycle This option selects the throttle rate of the main system clock during power management. The choices are: 12.5% 25.0% 37.5% 50.0% 62.5% 75.0% ZZ Active in Suspend This option, when enabled, puts the on-board L2 cache into sleep mode during power management. PCI/VGA Act-Monitor This option, when enabled, monitors activity of VGA for power management. Page 3-16 OPERATIONS MANUAL MCM/LPM-TX 010911 WinSystems - "The Embedded Systems Authority" CPU Fan Off In Suspend This option, when enabled, shuts off power to the CPU fan when the system is in suspended mode. PowerOn by Ring This option is not supported on the MCM/LPM-TX. Contact WinSystems’ tech support for further information. Resume by Alarm This option, when enabled, will wake the system from power management mode. IRQ 8 Break Suspend This option, when enabled, will wake the system from suspended mode using interrupt request 8. IRQ [3-7, 9-15],NMI This option, when enabled, will reset the power management timer if any of the following are accessed. IRQ 3-7 IRQ 9-15 NMI Primary IDE 0 This option, when enabled, will reset the power management timer when the primary IDE drive is accessed. Primary IDE 1 This option, when enabled, will reset the power management timer when the primary IDE drive is accessed. Secondary IDE 0 This option, when enabled, will reset the power management timer when the secondary IDE drive is accessed. 010911 OPERATIONS MANUAL MCM/LPM-TX Page 3-17 WinSystems - "The Embedded Systems Authority" Secondary IDE 1 This option, when enabled, will reset the power management timer when the secondary IDE drive is accessed. Floppy Disk This option, when enabled, will reset the power management timer when the floppy drive is accessed. Serial Port This option, when enabled, will reset the power management timer when the serial port is accessed. Parallel Port This option, when enabled, will reset the power management timer when the parallel port is accessed. Page 3-18 OPERATIONS MANUAL MCM/LPM-TX 010911 WinSystems - "The Embedded Systems Authority" ROM PCI/ISA BIOS (2A59IA2N) PnP/PCI CONFIGURATION Award SOFTWARE, INC. PnP OS Installed Resources Controlled By Reset Configuration Data : NO : Manual : Disabled IRQ-3 assigned to IRQ-4 assigned to IRQ-5 assigned to IRQ-6 assigned to IRQ-7 assigned to IRQ-9 assigned to IRQ-10 assigned to IRQ-11 assigned to IRQ-12 assigned to IRQ-14 assigned to IRQ-15 assigned to DMA-0 assigned to DMA-1 assigned to DMA-3 assigned to DMA-5 assigned to DMA-6 assigned to DMA-7 assigned to : PCI/ISA PnP : PCI/ISA PnP : Legacy ISA : PCI/ISA PnP : PCI/ISA PnP : Legacy ISA : Legacy ISA : PCI/ISA PnP : PCI/ISA PnP : Legacy ISA : Legacy ISA : PCI/ISA PnP : PCI/ISA PnP : PCI/ISA PnP : PCI/ISA PnP : PCI/ISA PnP : PCI/ISA PnP 3.8 PCI IDE IRQ Map Primary IDE INT# Secondary IDE INT# Used MEM base addr : ISA :A :A : N/A ESC : Quit ↑ ↓ → ← : Select Item F1 : Help PU/PD/+/- : Modify F5 : Old Value Shift) F2 : Color F6 : Load BIOS Defaults F7 : Load Setup Defaults PNP/PCI Configuration PnP OS Installed This option allows the user to assign whether the operating system is PnP. The options are: YES NO Resources Controlled By This option allows the user to select resource control of the system. The options are: Auto Manual 010911 OPERATIONS MANUAL MCM/LPM-TX Page 3-19 WinSystems - "The Embedded Systems Authority" Reset Configuration Data This option, when enabled, will reset the configuration data on power up. The options are: Enabled Disabled IRQ3-15 / DMA 0-7 The options in this section of the manual will assign each of the interrupts to a PCI/ISA Plug and Play device, or to a Legacy ISA device. The available options are: PCI/ISA PnP Legacy ISA PCI IDE IRQ Map This option allows the selection of the PCI IDE IRQ map. The options are: ISA PCI-AUTO PCI-SLOT 1 PCI-SLOT 2 PCI-SLOT 3 PCI-SLOT 4 Used MEM Base Address This option allows selection of the base address used by memory. The options are: N/A C800 CC00 D000 D400 D800 DC00 3.9 Load BIOS Defaults This main-menu option will cause the CMOS RAM to be loaded with the default values assigned by the factory. These are usually considered safe values and do not necessarily represent the highest performance values. Page 3-20 OPERATIONS MANUAL MCM/LPM-TX 010911 WinSystems - "The Embedded Systems Authority" 3.10 Load Setup Defaults This option will cause the CMOS RAM to be loaded with default setup values assigned by the factory. These are usually values that were determined to give a higher level of performance along with reliable operation. 3.11 Password Setting This option allows the setting of the security password. Pressing enter at the password prompt disables the security function completely. 3.12 IDE HDD Auto Detection This function allows modern IDE fixed disks to be used to their maximum potential by interrogating the driver as to its preferred configuration of tracks,heads, and sectors; and automatically loading these parameters into a “user defined” hard disk type. 3.13 Save and Exit Setup This function writes all changes to CMOS RAM and restarts the system. 3.14 Exit Without Saving This option exits setup without saving any changes made and then restarts the system. 010911 OPERATIONS MANUAL MCM/LPM-TX Page 3-21 WinSystems - "The Embedded Systems Authority" This Page Intentionally Left Blank Page 3-22 OPERATIONS MANUAL MCM/LPM-TX 010911 4 MCM-TX DiskOnChip Configuration 4.1 DiskOnChip Usage The MCM/LPM-TX supports the M-Systems DISK-ON-CHIP (DOC) flash device in sizes ranging from 8MB to 288MB. The DOC device contains a BIOS extension, the TFFS (True Flash File System), and the Flash memory all in a single 32-pin device. The DOC emulates a hard disk and can be used as a secondary hard disk to a physical IDE drive or it can be the only hard disk in the system. The DOC is installed into the socket at U8. Refer to the section 2.9 for correct device jumpering and enabling of the DOC. 4.1.1 DOC Initialization The DOC is initialized in an identical fashion to a fixed disk. DOS is booted (from floppy or hard disk), FDISK is run on the DOC drive (be sure to get the right drive), the system is rebooted and then the DOC is formatted using the DOS format command. If the /S switch was used during formatting and there is no other fixed disk device specified or attached to the system the DOC will become the boot device. If a hard disk is present, the DOC will become a secondary fixed disk. 010911 OPERATIONS MANUAL MCM/LPM-TX Page 4-1 WinSystems - "The Embedded Systems Authority" This Page Intentionally Left Blank Page 4-2 OPERATIONS MANUAL MCM/LPM-TX 010911 5 APPENDIX A I/O Port Map The following is a list of PC I/O ports. Addresses marked with a '-' are not used on the MCM/LPM-TX but their use should be carefully qualified so as not to conflict with other I/O boards. I/O addresses marked with a '+' are used on the MCM/LPM-TX board and are unique to the WinSystems’ design. I/O addresses marked with '**' are generally unused and should be the basis for the first choices in I/O address selection. Hex Range 000-00F **010-01F 020-021 +022-023 **024-03F 040-043 **044-05F 060-06F 070-071 **072-07F 080-08F **090-09F 0A0-0BF 0C0-0DF **0E0-0EF 0F0-0F1 **0F2-11F +120-12F **130-1DF +1E0-1EF 1F0-1FF -200-20F -210-21F -220-22F **230-237 -238-23B **240-277 278-27F **280-2AF -2B0-2DF -2E0-2E7 2E8-2EF **2F0-2F7 2F8-2FF -300-31F -320-32F **330-377 -378-37F -380-3AF 010911 Usage 8237 DMA #1 FREE 8259 PIC #1 Finali 486 Chipset Registers FREE 8254 Timer FREE 8042 Keyboard Controller CMOS RAM/RTC FREE DMA Page Registers FREE 8259 PIC #2 8237 DMA #2 FREE Coprocessor Control FREE WS16C48 HDIO FREE SSD, Led, Watchdog control Fixed Disk I/O Joystick port PCM SSD I/O Ports Soundblaster I/O ports FREE Bus Mouse FREE LPT1 FREE EGA Video GPIP Interface COM4 FREE COM2 Prototype Card XT Hard Disk FREE Parallel Printer SDLC OPERATIONS MANUAL MCM/LPM-TX Page 5-1 WinSystems - "The Embedded Systems Authority" -3B0-3BB -3C0-3CF 3E8-3EF 3F0-3F6 3F8-3FF Page 5-2 DMA EGA COM3 Floppy Disk COM1 OPERATIONS MANUAL MCM/LPM-TX 010911 6 APPENDIX B Interrupt Map No. Address Type Description 0 1 00 04 CPU CPU 2 3 4 5 08 0C 10 14 6 7 8 18 1C 20 9 24 A 28 CPU CPU CPU BIO 186 186 186 Hardware 286 Hardware 286 Hardware B 2C C 30 D 34 E 38 F 10 3C 40 11 44 12 13 14 15 48 4C 50 54 286 Hardware 286 Hardware 286 Hardware 286 Hardware 386 Hardware BIOS 286 BIOS 486 BIOS BIOS BIOS BIOS 16 17 18 19 1A 1B 1C 1D 1E 1F 58 5C 60 64 68 6C 70 74 78 7C BIOS BIOS BIOS BIOS BIOS BIOS BIOS BIOS BIOS BIOS Divide by 0 Single Step 386 Debug Exception NMI Breakpoint Overflow Print Screen Bound Exception Invalid opcode exception Coprocessor unavailable IRQ0 - 18.2Hz heart beat LIDT - Double fault exception IRQ1 - Keyboard interrupt Coprocessor segment IRQ2 - XT Reserved, AT-Slaved Controller Invalid TSS exception IRQ3 - COM2 Segment not present IRQ4 - COM1 Stack fault exception IRQ5 - XT Hard Disk, AT Free Protection fault exception IRQ6 - Floppy Disk Interrupt Page fault exception IRQ7 - LPT1 Video BIOS functions Coprocessor exception BIOS Equipment check Alignment check exception Memory Size function BIOS Disk functions BIOS serial functions Cassette/protected mode functions Keyboard BIOS functions BIOS printer functions SROM Basic Entry point (IBM) Boot loader function BIOS time of day functions Keyboard break vector User chained timer tick Video Initialization Floppy Disk parameter table CGA graphic character font 010911 OPERATIONS MANUAL MCM/LPM-TX Page 6-1 WinSystems - "The Embedded Systems Authority" 20 21 22 23 24 25 26 27 28 29 2A 2F 30 33 3F 40 80 84 88 8C 90 94 98 9C A0 A4 A8 BC C0 CC FC 100 MS-DOS MS-DOS MS-DOS MS-DOS MS-DOS MS-DOS MS-DOS MS-DOS MS-DOS MS-DOS MS-DOS MS-DOS MS-DOS MS-DOS MS-DOS BIOS 41 42 43 44 4A 50 51 5A 5B 5C 67 6D 70 71 72 73 74 75 76 77 80 F0 F1 FF 104 108 10C 110 128 140 144 168 16C 170 19C 1B4 1C0 1C4 1C8 1CC 1D0 1D4 1D8 1DC 200 3C0 3C4 3FC BIOS BIOS BIOS BIOS BIOS BIOS BIOS NET NET NET MS-DOS VGA Hardware Hardware Hardware Hardware Hardware Hardware Hardware Hardware Page 6-2 Program terminate DOS function call Terminate Address Ctrl-Break Address Fatal Error Vector Absolute disk read Absolute disk write Terminate Idle Signal TTY output MS-Net services Print Spool Long jump interface Mouse functions Overlay interrupt Floppy I/O when fixed disk is present Fixed disk 1 parameter table EGA Chain EGA Parameter table pointer EGA graphics character font AT Alarm exit address AT Alarm interrupt Mouse functions Functions Boot chain Net BIOS entry EMS functions VGA Service IRQ8 - Real Time clock IRQ9 - Redirected IRQ2 IRQ10 - Unassigned IRQ11 - Unassigned IRQ12 - Unassigned IRQ13 - Unassigned IRQ14 - IDE Fixed Disk IRQ15 - Unassigned Basic Not Used OPERATIONS MANUAL MCM/LPM-TX 010911 7 APPENDIX C MCM/LPM-TX Parts Placement Guide This Page Intentionally Left Blank 8 APPENDIX D MCM/LPM-TX Parts List This Page Intentionally Left Blank 09/21/01 BOM for Manuals PAGE 1 10:37:50 WinSystems, Inc. ASSM ITEM FROM: MCM-TX-166-32M ASSM ITEM THRU: MCM-TX-166-32M PARENT LOC FROM: <FIRST> DEFAULT COMPONENT LOCATION: ARLIN PARENT LOC THRU: <LAST> =================================================================================================================================== ITEM QTY LVL ITEM KEY ITEM DESCRIPTION BOM COMMENT TYPE REQUIRED =================================================================================================================================== MCM-TX-166-32M STD BUS PENTIUM CPU, 166 MHZ, 32MB DRAM STD BUS PENTIUM CPU, 166 MHZ, 32MB DRAM F 1.0 1 999-9999-001 SPECIAL NOTES 04-24-01 MEB ECO 01-21 I 1.0 1 999-9999-001 SPECIAL NOTES 03/21/01 MEB ECO 01-11 I 1.0 1 999-9999-001 SPECIAL NOTES 11/20/00 MEB (REVA) I 1.0 1 999-9999-001 SPECIAL NOTES SPECIAL NOTES I 1.0 1 0296-000-0000C ASSY-SMT-TOP, L/M-TX ALL REV.C ASSY-SMT-TOP, L/M-TX ALL REV.C F 1.0 2 999-9999-001 SPECIAL NOTES 04-24-01 MEB ECO 01-21 I 1.0 2 999-9999-001 SPECIAL NOTES 03/21/01 MEB ECO 01-11 I 1.0 2 999-9999-001 SPECIAL NOTES 11/20/00 MEB (REVA) I 1.0 2 999-9999-001 SPECIAL NOTES SPECIAL NOTES I 0.0 2 400-0296-000C PCB, MCM/LPM-TX REV.C I 1.0 2 601-0220-503 RES 22 Ohm 5% 1/10w 0805 R1 I 1.0 2 602-0220-524 RN 22 Ohm, 5%, 4RES ARRAY RP2,RP3,RP5 I 3.0 2 602-0330-524 RN 33 Ohm, 5%, 4RES ARRAY RP1,RP4 I 2.0 2 603-1007-303 CAP 10pF 50v +/- .5pF CER 0805 C21 I 1.0 2 603-1047-803 CAP .1uF 50v 20% CER 0805 C12,C14 I 2.0 2 603-1065-82D CAP 10uF 25v 20% TAN 6032 C11,C13,C15,C16,C17,C20,C23,C24 I 8.0 2 603-2207-503 CAP 22PF 50v 2% NPO 0805 C9,C10 I 2.0 2 603-3372-82F CAP 330uf TANT 10v 20% C2-C8,C22 I 8.0 2 603-4763-82E CAP 47uF 16v 20% TAN 7343 C1 I 1.0 2 603-68R7-203 CAP 6.8pF 50v +/-.5pf CER 0805 C18,C19 I 2.0 2 605-2001-000 FERRITE BEAD, SMT 3528 FB1,FB2 I 2.0 2 606-0004-000 IC, CTX5-4 5UH 4AMP XFORMER T1,T2 I 2.0 2 607-0005-005 LED, GREEN SMT D1 I 1.0 2 607-0006-005 LED, RED SMT D2 I 1.0 2 607-0010-013 IC UPS5819 POWERMITE SCHOTTKY DIODE 1A D3,D4 I 2.0 2 619-2245-016 IC 74FCT162H245ATPV U24,U25,U26 I 3.0 2 620-0013-125 IC, INTEL, GC80503CS166-166EXTS U1 I 1.0 2 621-0025-016 IC, SUPER I/O CONTROLLER U14 I 1.0 2 622-0017-019 IC, FREQUENCY SYNTH 48 PIN U13 I 1.0 2 623-0008-025 IC, INTEL FW82439TX U16 I 1.0 2 623-0009-025 IC, INTEL FW82371EB U17 I 1.0 2 630-0002-008 IC 32K X 8 FAST SRAM 12 NS SOJ U10 I 1.0 2 630-0005-016 IC, 64K x 64 7ns SYNC SRAM 128PIN PQFP U12 I 1.0 2 650-0032-002 SOCKET 32P AMP 822498-1 (28) U9 I 1.0 2 670-0003-026 IC LT1963EST-2.5 2.5V LDO REGULATOR U11 I 1.0 2 681-0004-001 XTAL 32.768KHZ SMT Y2 I 1.0 2 681-0002-005 XTAL 14.31818 MHZ 18PF SMT Y1 I 1.0 ----------------------------------------------------------------------------------------------------------------------------------SUB-ASSEMBLY TOTAL: 0296-000-0000C ARLIN - 32 Items ----------------------------------------------------------------------------------------------------------------------------------1 0296-001-0000C ASSY-SMT-BOT, L/M-TX ALL MEM SIZES REV.C ASSY-SMT-BOT, L/M-TX ALL MEM SIZES REV.C F 1.0 2 999-9999-001 SPECIAL NOTES 04-24-01 MEB ECO 01-21 I 1.0 2 999-9999-001 SPECIAL NOTES 03/21/01 MEB ECO 01-11 I 1.0 2 999-9999-001 SPECIAL NOTES 11/20/00 MEB (REVA) I 1.0 2 999-9999-001 SPECIAL NOTES SPECIAL NOTES I 1.0 09/21/01 BOM for Manuals PAGE 2 10:37:51 WinSystems, Inc. ASSM ITEM FROM: MCM-TX-166-32M ASSM ITEM THRU: MCM-TX-166-32M PARENT LOC FROM: <FIRST> DEFAULT COMPONENT LOCATION: ARLIN PARENT LOC THRU: <LAST> =================================================================================================================================== ITEM QTY LVL ITEM KEY ITEM DESCRIPTION BOM COMMENT TYPE REQUIRED =================================================================================================================================== 2 125-0008-000 TRANSISTOR SI4947DY DUAL P-CHANNEL FET U38 I 1.0 2 601-0000-503 RES 0 Ohm 5% 1/10w 0805 R25,R26,R27,R28,R40 I 16.0 2 999-9999-001 SPECIAL NOTES W1,W2,W3,W4,W5,W6,W9=1-2 I 1.0 2 601-0100-503 RES 10 Ohm 5% 1/10w 0805 R53,R54,R55,R56,R58 I 5.0 2 601-0101-503 RES 100 Ohm 5% 1/10w 0805 R65,R66 I 2.0 2 601-0102-503 RES 1K Ohm 5% 1/10W 0805 R36,R39,R42,R59,R60,R62,R71 I 7.0 2 601-0103-503 RES 10K Ohm 5% 1/10W 0805 R34,R35,R37,R38,R45,R48 I 6.0 2 601-0203-503 RES 20K Ohms 5% 1/10W 0805 R52,R57 I 2.0 2 601-0220-503 RES 22 Ohm 5% 1/10w 0805 R69,R73 I 2.0 2 601-0331-503 RES 330 Oh, 5%, 0805 R12,R13,R32,R33,R43,R44,R61,R63,R64,R67, I 11.0 2 999-9999-001 SPECIAL NOTES R70 I 1.0 2 601-0221-503 RES 220 Ohm 5% 1/10w 0805 R74 I 1.0 2 601-0471-503 RES 470 Ohm 20% 1/10w 0805 R41 I 1.0 2 601-0472-503 RES 4.7K Ohm 5% 1/10w 0805 R51 I 1.0 2 601-0474-503 RES 470K Ohm 5% 1/10W 0805 R20,R72 I 2.0 2 601-0564-503 RES 560K Ohm 5% 1/10W 0805 R21 I 1.0 2 601-0683-503 RESISTOR 68K 5% 0805 SMT R49,R50 I 2.0 2 601-1432-303 RES 14.3K Ohm 1% 1/10w 0805 R46 I 1.0 2 601-4532-303 RES 45.3K 1% 0805 R47 I 1.0 2 602-0100-524 RN 10 Ohm, 5%, 4RES ARRAY RP55,RP56,RP57,RP59,RP60,RP61 I 7.0 2 602-0101-524 RN 100 Ohm, 5%, 4RES ARRAY RP49 I 1.0 2 602-0102-524 RN 1K Ohm, 5%, 4RES ARRAY RP22,RP25,RP34,RP53,RP54,RP66 I 7.0 2 602-0103-524 RN 10K Ohm, 5%, 4RES ARRAY RP17-RP21,RP26,RP27,RP28,RP33,RP36,RP37, I 21.0 2 999-9999-001 SPECIAL NOTES RP43,RP44,RP47,RP48,RP50,RP52,RP62-RP65 I 1.0 2 602-0272-524 RN 2.7K Ohm, 5%, 4RES ARRAY RP35,RP46,RP51,RP58 I 4.0 2 602-0330-524 RN 33 Ohm, 5%, 4RES ARRAY RP16,RP67,RP68,RP69,RP70,RP71,RP72 I 7.0 2 602-0472-524 RN 4.7K Ohm, 5%, 4RES ARRAY RP23,RP24,RP29,RP30,RP31,RP32,RP40,RP42, I 9.0 2 999-9999-001 SPECIAL NOTES RP45 I 1.0 2 602-0822-524 RN 8.2K Ohm, 5%, 4RES ARRAY RP38,RP39,RP41 I 3.0 2 602-0220-524 RN 22 Ohm, 5%, 4RES ARRAY RP73 I 1.0 2 603-1027-803 CAP 1000pF 50v 20% CER 0805 C41 I 1.0 2 603-1047-803 CAP .1uF 50v 20% CER 0805 C42-C53,C57-C65,C68-C71,C74,C75,C78, I 83.0 2 999-9999-001 SPECIAL NOTES C81-C85,C95-C125,C128,C129,C131-C139, I 1.0 2 999-9999-001 SPECIAL NOTES C141,C143-C150 I 1.0 2 603-2207-603 CAP 22pF 50v 5% NPO 0805 C176 I 1.0 2 603-1052-803 CAP 1uF 10v 20% CER 0805 C54,C55,C56,C66,C67,C72,C73,C79,C80, I 14.0 2 999-9999-001 SPECIAL NOTES C126,C127,C130,C140,C142 I 1.0 2 603-1055-807 CAP 1uF 25v 20% CER 1812 C86,C87,C89,C93,C94,C105 I 6.0 2 603-2227-803 CAP .0022uF 50v 20% CER 0805 C76,C77 I 2.0 2 603-3317-803 CAP 330PF 20% 50V 0805 SMT X7R C88,C92 I 2.0 2 603-4707-803 CAP 47pF 50v 20% CER 0805 C35,C40 I 2.0 2 603-56R7-303 CAP 5.6pF 50V +/-.5PF 0805 SMT NPO C90,C91 I 2.0 2 607-0008-000 DIODE SMT SCHOTTKY SOT-23 D15-D19 I 5.0 2 611-0004-001 IC, 74HC04M U39 I 1.0 2 611-0245-002 IC, 74HC245DW (SM) U41,U45 I 2.0 2 614-0008-001 IC, 74F08SCX (NAT) QUAD AND GATE U42 I 1.0 09/21/01 BOM for Manuals PAGE 3 10:37:51 WinSystems, Inc. ASSM ITEM FROM: MCM-TX-166-32M ASSM ITEM THRU: MCM-TX-166-32M PARENT LOC FROM: <FIRST> DEFAULT COMPONENT LOCATION: ARLIN PARENT LOC THRU: <LAST> =================================================================================================================================== ITEM QTY LVL ITEM KEY ITEM DESCRIPTION BOM COMMENT TYPE REQUIRED =================================================================================================================================== 2 612-0240-002 IC, 74HCT240 (SM) U46 I 1.0 2 612-0014-001 IC, 74HCT14 (SM) U43 I 1.0 2 622-0007-001 IC, MAX692ACSA (Maxim only!) U44 I 1.0 2 660-0002-002 TRANS MMBT2222ALT1 SOT-23 Q1,Q6 I 2.0 2 665-0002-008 IC Si4410DY SILICONIX,TEMIC n-CHANNEL Q2,Q3,Q4,Q5 I 4.0 2 677-0005-019 IC LTC1873EG DUAL 2-PHASE SWITCHING U40 I 1.0 ----------------------------------------------------------------------------------------------------------------------------------SUB-ASSEMBLY TOTAL: 0296-001-0000C ARLIN - 56 Items ----------------------------------------------------------------------------------------------------------------------------------1 0296-002-0000C ASSY-TH, L/M-TX ALL REV.C ASSY-TH, L/M-TX ALL REV.C F 1.0 2 999-9999-001 SPECIAL NOTES 04-21-01 MEB ECO 01-21 I 1.0 2 999-9999-001 SPECIAL NOTES 03/21/01 MEB ECO 01-11 I 1.0 2 999-9999-001 SPECIAL NOTES 11-20-00 MEB (REVA) I 1.0 2 999-9999-001 SPECIAL NOTES SPECIAL NOTES I 0.0 2 111-0043-000 BATTERY KEEPER LTC-3PN-S2 BT1 I 1.0 2 111-0032-000 INSULATOR BATTERY CR2032 UNDERNEATH BT1,LS1 I 2.0 2 200-0104-000 CONNECTOR PC/104 COMM CON 1184C-104G2 J17 I 1.0 2 200-0120-000 CONN PC104 PLUS COMM CON 1241-120G J16 I 1.0 2 201-0003-001 HDR 3 PIN MOLEX 22-11-2032 J3 I 1.0 2 201-0004-003 HDR MOLEX 4 POS 22-11-2042 J1 I 1.0 2 201-0005-003 HEADER 5 PIN LATCH MOLEX 22-11-2052 J5 I 1.0 2 201-0010-021 HDR 10 ST IDH-10LP-S3-TR (1,800) J4 I 1.0 2 201-0034-021 HDR 34 ST IDH-34LP-S3-TR (720) J6 I 1.0 2 201-0036-010 HDR 1X36 UN TSW-136-07-G-S (SAM) J21,J23=1X2 I .9 2 999-9999-001 SPECIAL NOTES J8-J10,J12-J15,J20,J22=1X3 I 1.0 2 201-0040-021 HDR 40 ST IDH-40LP-S3-TR (576) J7 I 1.0 2 201-0050-121 HEADER 50 RA IDH-50LP-SR3-TR (350) J2 I 1.0 2 201-0072-120 HDR 2X36 UN TSW-136-07-G-D J11=2X2 J19=2X16 J24=2X3 I .6 2 250-0320-001 TERMINAL STRIP 316-93-132-41-006000 U8=2X16 I 1.0 2 730-0026-000 PIEZO TRANSDUCER BRP2407L-30 LS1 I 1.0 2 250-0320-200 SKT STRP 32 POS SS-132-G-2 (SAM) U3,U6=2X12 U2,U4,U5,U7=2X4 I 1.0 2 200-0243-100 SOCKET 24 P .3 ICO-243-S8A-T (1,496) U15,U18,U23 I 3.0 ----------------------------------------------------------------------------------------------------------------------------------SUB-ASSEMBLY TOTAL: 0296-002-0000C ARLIN - 22 Items ----------------------------------------------------------------------------------------------------------------------------------1 0296-030-0000C ASSY, TOP-SMT 32MEG L/M-TX REV.C ASSY, TOP-SMT 32MEG L/M-TX REV.C F 1.0 2 999-9999-001 SPECIAL NOTES 04-24-01 MEB ECO 01-21 I 1.0 2 999-9999-001 SPECIAL NOTES 03/21/01 MEB ECO 01-11 I 1.0 2 999-9999-001 SPECIAL NOTES 11/20/00 MEB (REVA) I 1.0 2 999-9999-001 SPECIAL NOTES SPECIAL NOTES I 0.0 2 631-0006-023 4M X 16 SDRAM 54 PIN TSSOP U19,U20,U21,U22 I 4.0 ----------------------------------------------------------------------------------------------------------------------------------SUB-ASSEMBLY TOTAL: 0296-030-0000C ARLIN - 5 Items ----------------------------------------------------------------------------------------------------------------------------------1 0296-100-0000C SUB-ASSY, L/M-TX ALL REV.C SUB-ASSY, L/M-TX ALL REV.C F 1.0 2 999-9999-001 SPECIAL NOTES 04-24-01 MEB ECO 01-21 I 1.0 09/21/01 BOM for Manuals PAGE 4 10:37:52 WinSystems, Inc. ASSM ITEM FROM: MCM-TX-166-32M ASSM ITEM THRU: MCM-TX-166-32M PARENT LOC FROM: <FIRST> DEFAULT COMPONENT LOCATION: ARLIN PARENT LOC THRU: <LAST> =================================================================================================================================== ITEM QTY LVL ITEM KEY ITEM DESCRIPTION BOM COMMENT TYPE REQUIRED =================================================================================================================================== 2 999-9999-001 SPECIAL NOTES 03/21/01 MEB ECO 01-11 I 1.0 2 999-9999-001 SPECIAL NOTES 11/20/00 MEB (REVA) I 1.0 2 999-9999-001 SPECIAL NOTES SPECIAL NOTES I 0.0 2 730-0083-000 IC, SP208CP (SIPEX), MAX208CNG (15) U3,U6 I 2.0 2 901-0011-000 IC, PALC22V10-35PC (15,TI) (17,CYP) U15 CS=2F62 SPRINT\MCMTX\MCMTXU15.JED I 1.0 2 901-0040-000 IC ATF750C-7PC U23 CS=13EB SPRINT\MCMTX\MCMTXU23.JED I 2.0 2 999-9999-001 SPECIAL NOTES U18 CS=AFCD SPRINT\MCMTX\MCMTXU18.JED I 1.0 2 637-0003-015 IC, AT29C010A-12JC 128K X 8 FLASH ROM U9 CS=5617\SPRINT\MCMTX\REL0129.BIN I 1.0 2 500-0001-000 EJECTOR SCANBE S208-1 (W/O Roll pin) STAMP RED: "MCM-TX"/STAMP BLUE:"LPM-TX" I 1.0 2 500-0002-000 ROLL PIN MS171492 ROLL PIN MS171492 I 1.0 2 999-9999-001 SPECIAL NOTES *TEST JUMPERING: I 1.0 2 999-9999-001 SPECIAL NOTES J11=1-2 3-4 I 1.0 2 999-9999-001 SPECIAL NOTES J13=2-3 I 1.0 2 999-9999-001 SPECIAL NOTES J14=2-3 I 1.0 2 999-9999-001 SPECIAL NOTES J15=2-3 I 1.0 2 999-9999-001 SPECIAL NOTES J19=9-10 23-24 I 1.0 2 999-9999-001 SPECIAL NOTES J20=1-2 I 1.0 2 999-9999-001 SPECIAL NOTES J21=1-2 I 1.0 2 999-9999-001 SPECIAL NOTES J22=2-3 I 1.0 2 999-9999-001 SPECIAL NOTES J24=4-6 3-5 I 1.0 ----------------------------------------------------------------------------------------------------------------------------------SUB-ASSEMBLY TOTAL: 0296-100-0000C ARLIN - 21 Items ----------------------------------------------------------------------------------------------------------------------------------1 910-0024-000 LABEL, STATIC SENSITIVE 130-02 LABEL, STATIC SENSITIVE 130-02 I 1.0 1 950-0001-000 BAG STATIC BARRIER 07-0610 6X10 BAG STATIC BARRIER 07-0610 6X10 I 1.0 1 502-0016-000 HEAT SINK,BDN14-3CB 1.41"SQUARE x.355"HT ATTACH TO U1 WITH ADHESIVE MATERIAL I 1.0 1 502-0009-000 HEAT SINK 1' X 1" MATERIAL/PART# RD-339C ADHESIVE MATERIAL I 1.0 1 910-0037-000 LABEL, AWARD BIOS, PENTIUM LABEL, AWARD BIOS, PENTIUM I 1.0 =================================================================================================================================== TOP ASSEMBLY TOTAL: MCM-TX-166-32M ARLIN - 14 Items =================================================================================================================================== REPORT RECAP -----------0 WARNING(S) PARAMETER RECAP --------------PARAMETER KEY REPORT TITLE : 10 BOM with Ref. Desc. : BOM for Manuals ASSM ITEM RANGE PARENT LOC RANGE PRODUCT KEY RANGE COMMODITY KEY RANGE : : : : MCM-TX-166-32M <FIRST> <FIRST> <FIRST> DEFAULT COMP LOC : ARLIN BOM STATUS PRIORITY : A THRU THRU THRU THRU MCM-TX-166-32M <LAST> <LAST> <LAST> COSTING METHOD QUANTITY TO EXPLODE USE SCRAP FACTOR (Y/N) UPDATE INV STD COST NO. LEVELS TO EXPLODE COLUMNS OF DESC TEXT SHORT OR LONG (S/L) PRINT ITEM DESC (Y/N) : : : : : : : : A 1 N N 999 42 S Y ">
Download
Advertisement
Key features
Intel Tillamook Pentium MMX 166MHz
32MB or 64MB of system SDRAM
Socket for up to 288MB bootable DiskOnChip or BIOS extension EPROM
Two RS-232 serial ports
USB support
Ultra DMA/33 IDE Hard drive controller
PC/104 and PC/104- Plus expansion connectors
AT keyboard controller and PS2 mouse support
On-board CPU power supply
Frequently asked questions
The MCM/LPM-TX supports up to 64MB of onboard DRAM.
The MCM/LPM-TX supports PC/104 and PC/104-Plus expansion buses.
The DiskOnChip socket supports M-Systems’ DiskOnChip Flash modules, which can be used as a solid-state disk (SSD) drive.
The MCM/LPM-TX provides two RS-232 serial ports, which can be configured for RS-422, RS-485 or J1708 with the addition of optional driver ICs.
The MCM/LPM-TX has a standard operating temperature range of -40°C to +85°C.
The MCM/LPM-TX comes standard with an Award BIOS with Setup in ROM.
The MCM/LPM-TX features an Intel Pentium 166MMX processor, 32MB or 64MB of onboard DRAM, a full 16-bit PC/104 expansion bus, two RS-232 serial ports, USB support, Ultra DMA/33 IDE hard drive controller, and an onboard 32-pin silicon disk socket. It is also highly integrated and offers a small form factor.