advertisement
Page 6
Clausing
Drills are equipped with a
Spindle
Guard that locks in an upright position, away from spindle nose, for easy tool changes
.
Style A
Floor Drill
22” x 19.5”
(559 x 495mm)
Table, 66"
(1676mm) column standard and 1/2" cored
T-slots on 9" centers for table and base.
SEE MODELS
Clausing 20"
(508mm)
Variable Speed Drills
Dial to the best rpm for the tool and material while the job is running, with a Clausing
Two Speed Variable Speed Drill Press.
• 150 to 2000 rpm... speeds to drill large holes, small
holes to spot face, counterbore and ream.
• A flip of the switch changes from low range to high
range, perfect for production applications with quick
change tooling.
• Greater capacity too with Clausing Two Speed,
production rated 1" in cast iron, 3/4" in steel
with optional power feed.
Handle more jobs ... better, faster with a
Clausing 20" (LOW/HIGH drill press).
More Features for Superior
Performance...
• Heavy-duty precision head... all bearing surfaces are
precision bored simultaneously for exact alignment.
Eight ball bearings support the drive and spindle, lower
spindle bearing has a double row to absorb both radial
and thrust loads.
• 3MT spindle... with 6-1/2" travel, 2-1/2" diameter quill
and thread adjustable depth stop.
• 4" column with 3/16" thick wall for great rigidity and
accuracy.
• Precision ground 22" x 19" coolant trough table, handles
large parts and fixtures.
Powerful
Countershaft Drive
Style B
Head & Column
Assembly mounted on optional
20-501 Table
Assembly*
SEE MODELS
*Shown with optional table assembly
• Three V-belts and a cog belt transmit positive
power to the spindle.
Clausing’s heavy-duty drive delivers full power to spindle at all speeds.
Clausing 20"
(508mm)
Drill Specifications & Electrical Options
Specifications:
Optional Electrical Equipment*
Capacity, Hand Feed 1.25"
(31.75mm)
Dia.
Production Rated, with Optional
Power Feed, 1-1/2 Hp Motor 1"
(25.4mm) in Cast Iron
3/4"
(19mm) in Mild Steel
Drill to Center of Circle 20"
(508mm)
Dia.
Spindle Nose No. 3MT, 1.74"
(44.2mm)
OD
Spindle Travel 6.5"
(165mm)
Column Ground Steel, 4"
(102mm)
Dia.,
3/8"
(9.5mm)
Thick Wall
Quill (Ground Steel) 2.5"
(63.5mm)
Dia.
Quill Return Spring, Capacity 40 lbs.
(18kg)
TABLE, DRILL PRESS Style A
Working Surface 22" x 19.5"
(559 x 495mm)
Table slots Two, 15.5"
(394mm)
Long, for
.5"
(12.7mm)
T-bolt
Table Load Capacity 350 lbs.
(159kg)
Table Travel, One Setting 20"
(508mm)
Spindle to Table, Maximum 33.125"
(841mm)
BASE, DRILL PRESS Style A
Working Surface, Ground 15.5" x 13"
(394 x 330mm)
Base T-slots Two, 13"
(330mm)
Long, for
.5" T-bolt
Spindle to Base, Maximum 43.375"
(1102mm)
DRILL PRESS Style B
Column Bracket to Center of Spindle 9.25"
(235mm)
Column to Center of Spindle 10"
(254mm)
Spindle to Table, Max. Distance 25.437"
(646mm)
Column Length 43"
(1092mm)
Min. Center to Center Distance 20"
(508mm)
Motor ... NEMA Frame Sizes 182 and 184
Shipping Weights, Approximate, with Motors
Drill Press Style A 630 lbs.
(286kg)
Drill Press Style B 390 lbs.
(177kg)
For Factory Installation Only
NOTE: Magnetic starters protect motor against overload, low and no voltage-Thermal Overload Unit NOT required.
For Single Speed Motor No
. 2371 MAGNETIC STARTER.*
Protects motor against overload, low and no voltage. Motor will not automat ically restart when power is restored. Transformer provides
110v at start/stop push button. 6 lbs.
No. 2371-15 MAGNETIC STARTER for 3-phase. Includes disconnect switch and 110 volt push-buttons.
No. 2377 REVERSING DRUM SWITCH for 1 & 3-phase.* Protects motor against overload, low and no voltage. Motor will not automatically restart when power is restored. Transformer provides
110v at start/stop push button switch. 6 lbs.
For 2-Speed Motor
No. 2375 MAGNETIC STARTER and REVERSING DRUM SWITCH, with reverse on low speed. * Protects motor against overload, low and no voltage. Motor will not automatically restart when power is restored. Transformer provides 110v at start/stop push button switch. 6 lbs.
*Controls for field installation, and for single phase ... price on application.
Overall Dimensions Width Depth Height
Drill Press Style A 22"
(559mm)
36"
(914mm)
69"
(1753mm)
Drill Press Style B 20"
(508mm)
3.25"
(870mm)
51.625"
(1311mm)
FLOOR MODELS FURNISHED with: No. 3MT spindle; table elevating mechanism; switch; belt guard; spindle guard. Motors and switches are installed and wired, ready to connect to power.
Design and specifications are subject to change without notice.
Infinitely Variable Speed Countershaft Drive
MODEL SELECTION CHART
Style A Style B
Motor Floor Drill Head & Column
Furnished 22" x 19" Table Assembly
Two Speed Infinitely Variable Speeds: 150-2000 rpm
1-1/2 - 3/4 Hp
2-speed, 3-phase, 220v* 2276 2286-300
2-speed, 3-phase, 440v* 2277 2287-300
Infinitely Variable Speeds: 200-1300 rpm
1-1/2 Hp
1 1 ⁄
2
Hp, 3-ph, 1140 rpm 2275 2285-300
Infinitely Variable Speeds: 300-2000 rpm
1-1/2 Hp
1 1 ⁄
2
Hp, 1-ph, 1725 rpm 2272 2282-300
1 1 ⁄
2
Hp, 3-ph, 1725 rpm 2274 2284-300
**Style B
Head &
Column
Assembly
43"
(1092mm)
Column Standard
*Motor, 1 1 ⁄
2
3 ⁄
4 hp 1800/900 rpm, 60hz. SPECIFY VOLTAGE... When voltage is not specified, motor will be wired on lower voltage. Motors are ball bearing. 3-phase single speed motors are 208/220/440v, 60hz. Single-phase motors are capacitor-start, 115/230v, 60hz.
**Head and Column Models Furnished with: No. 3MT spindle, head elevating mechanism, column, mounting flange, switch and belt guard.
Motor and switches are installed and wired, ready to connect to power.
Page 7
Clausing 20"
(508mm)
Multiple Spindle Drill Presses
Clausing multiple spindle drills can be custom built with up to four 20" heads. When ordering a multiple spindle drill press use the table model number below, plus the appropriate head and column assemblies for the corresponding number of heads.
Mix and match any number of drill heads as your requirements demand. Example: If you wish to have a
3 spindle drill press with three-20" heads you would order (1) 20-503 table assembly and (3) 2286-300 20" head assemblies. Tell us the order to mount the heads and you have the 3-spindle drill you require.
If you have special requests, contact us for a quotation. Special orders priced on application.
20-501 • 1-Spindle
20"
(508mm)
(1) 2286-300
Head & Column
Assembly and
20-200 22" x 25"
(559 x 635mm)
Production Base
40"
(1016mm)
45.5
"
(1156mm)
20"
(508mm)
One Piece Table, Two Legs Furnished
20-503 • 3-Spindle
(4) 2286-300
Low/High Head
& Column
Assembly and
20-504 85.5" x 29.5"
(2172 x 750mm)
Table with Legs
20-502 • 2-Spindle
38
1 /
4
"
34"
26
3 /
16
"
24"
(610mm)
25.5"
(648mm)
10"
(254mm)
20"
(508mm)
40"
(1016mm)
45.5
"
(1156mm)
10"
(254mm)
One Piece Table, Two Tegs Furnished
20-504 • 4-Spindle
25 7 /
16
"
MAX.
85
5 /
8
"
MAX.
34
"
9" 10 "
9
1 /
4
"
6"
4
1
29
1 /
2
"
/
2
"
24
3 /
4
"
13"
(330mm)
27"
(686mm)
80"
(2032mm)
85.5"
(2172mm)
Page 8
One Piece Table, Two Legs Furnished
24"
(610mm)
25.5"
(648mm)
10"
20"
(508mm)
80"
(2032mm)
85.5"
(2172mm)
One Piece Table, Two Legs Furnished
Clausing 20"
(508mm)
Drill Accessories
Programmable Macro-Driller Power Feed
Coolant
System
No. 7044
Coolant System. 5 gallon capacity, 110 volt, 60 cycle single-phase motor, for single spindle drills. Flexible nozzle with regulator valve, plastic hose, clamps, fittings, cord and plug. 18 lbs.
No. 7044-2 Coolant
System. For two (2) spindle drills. 5 gallon capacity, 110 volt, 60 cycle single-phase motor. Complete with all valves, hose, fittings, cord and plug.
No. 7044-3 Coolant System. For three (3) spindle drills.
Like No. 7044-2 except arranged for 3 spindles.
No. 7044-4 Coolant System. For four (4) spindle drills.
Like No. 2044-3 except arranged for 4 spindles.
No. 2215-1 or 2215-1/440 (for 440v machines)
The Programmable Macro-Driller can be installed on any model of
Clausing 20" drill press, either at time of purchase or as a retrofit.
It allows you to automate hole drilling and is most effective on deep hole ‘Peck’ drilling. Peck drilling is used to prevent shavings from tangling with the drill bit and breaking it. The up and down motion of
‘peck drilling’ allows the drill to go slightly deeper into the material then with drawing to pull the chips out of the hole. The Programmable
Macro-Driller is easy to program by using the keypad.
Drill Press
Lamp
No. 7022 Lamp.
Cool burn-proof shade, aluminum reflector, switch,
19" (483mm) flexible arm, magnetic base, 6' (1.5m) cord and plug.
Programmable Macro-Driller Specification
Quill Travel: 6.4" (62mm)
Feedrate Range: 0.01 - 120 ipm (0.25 - 3000mm/min)
Peck Steps: 0.001" - 6.4" (0.02 - 162mm)
Maximum Pecks per Hole: 1400
Accurate Hole Depth: ±0.001" (0.02mm)
Maximum Quill Force: 1250 lbs. (568kg)
LED Numerals: 5/8" (15.9mm) High
Control Power: 220/230 volt, 50/60 Hz
Single or Three Phase
Max. Drilling Capacity: 3/4" (19mm) in Cast Iron
5/8" (16mm) in Mild Steel
Drill Press
LED Light
No. 20-LED LED Light
The New Clausing 120v LED Work Light mounts in the slot under the Drill Head behind the spindle.
The three ultra bright LED lights provides ample lighting over the entire work area.
Electric Foot Control
No. 302 Electric Foot Control
No. 302R1 Electric Foot
Control with reversing drum switch for single speed drill
No. 302R2 Electric Foot Control with reversing drum switch for two speed drills Start and stop drill from foot pedal
Drill
Chuck and
Arbor
Electronic DRO
No. 20-900
Columns
No. 2294-AMT 66" (1676mm) Column in lieu of
43" (1092mm) Column 78 lbs. (35kg)
No. 2349-AMT 90" (2286mm) Column in lieu of
66" (1676mm) Column 107 lbs. (49kg)
Mesh Guard
No. SK-208
Top Mesh
Belt Guard
No. 1897 Key-Type Chuck. Takes
3⁄16" (4.8mm) to 3⁄4" (19mm) Drills.
Adapts to 3MT Spindle with
No. 1898 arbor. 4 lbs. (1.8kg)
No. 1898 Arbor. Adapts No. 1897 to
3MT Spindle. 1 lb. (.5kg)
• Easy to read LCD display
• Data output port
• 0" - 6" measuring range
• 0.005" (0.01mm) resolution
• 59 in./sec. measuring speed
Page 9
TL25
Clausing/Ibarmia Series T
Geared-drive Round Column Drills
A heavy-duty Industrial Drilling Machine, designed for easy operation with manual feed
Standard Features and Equipment:
• Drilling capacity in steel: 1"
(25mm) maximum
• Drilling capacity in cast iron: 1.18"
(30mm) maximum
• Tapping capacity in steel: .71"
(18mm) maximum
• Tapping capacity in cast iron: .87"
(22mm) maximum
• Depth scale and adjustable depth stop
• “RS” models are equipped with automatic feed reversing
system for tapping
• Thermomagnetic switch
• Spindle reversing switch
• Automatic tool ejector
• Emergency STOP
• High/Low speed range selector
• Drill guard with microswitch
Optional Equipment:
• Floor Cabinet with Shelves
• Floor Cabinet with Drawer and Door
• Rotating Table (TM/TL Models)
• Cross Slide Table
• Cycle Start Foot Pedal
• Foot Pedal for Reversing
• Work Light with Magnetic Base
• Coolant System with Independent Container
Page 10
Optional
PKB
Cabinets
TM25
TS25
Capacities, Specifications and Dimensions:
Standard Models TS25 TM25 TL25
Auto feed reversing for tapping models TS25RS TM25RS TL25RS
Capacities:
Maximum Drilling Capacity in Steel 1"
(25mm)
1"
(25mm)
1"
(25mm)
Maximum Drilling Capacity in Cast Iron 1.18"
(30mm)
1.18"
(30mm)
1.18"
(30mm)
Maximum Tapping Capacity in Steel .71"
(18mm)
.71"
(18mm)
.71"
(18mm)
Maximum Tapping Capacity in Cast Iron .87"
(22mm)
.87"
(22mm)
.87"
(22mm)
Drill Head:
Spindle Taper 3MT 3MT 3MT
Quill Diameter 2.44"
(62mm)
2.44"
(62mm)
2.44"
(62mm)
Spindle Travel (Drilling Depth) 4.72"
(120mm)
4.72"
(120mm)
4.72"
(120mm)
Main Motor Power 1/1.5 hp
(.73/1.1 Kw)
No. of Speeds (See Speed Charts) 8 8 8
Dimensions and Weights:
Height (A) 47.6"
(1210mm)
48.4"
(1230mm)
75.8"
(1925mm)
Height (A1) 79.1"
(2010mm)
79.9"
(2030mm)
-
Base: Length x Width (B) 22" x 15"
(560x380mm)
22" x 15"
(560x380mm)
24" x 15"
(600x380mm)
Base to Spindle (C) See (E) 20.9"
(530mm)
47.6"
(1210mm)
Spindle Center to Column (D) 9.84"
(250mm)
9.84"
(250mm)
9.84"
(250mm)
Spindle to Table (E)
Minimum 4.33"
(110mm)
1.18"
(30mm)
4.13"
(105mm)
Maximum 19.7"
(500mm)
12.6"
(320mm)
25.2"
(640mm)
Worktable: Length x Width (F) - 10.6" x 11.8"
(270 x 300mm)
Base Height (G) 3.1"
(80mm)
3.1"
(80mm)
3.7"
(95mm)
Column Diameter (H) 3.94"
(100mm)
3.94"
(100mm)
3.94"
(100mm)
Floor to Top of Base (I) 34.6"
(880mm)
34.6"
(880mm)
-
Cabinet Height (J) 31.5"
(800mm)
31.5"
(800mm)
-
Net Weight 298 lbs.
(135kg)
364 lbs.
(165kg)
408 lbs.
(185kg)
Shipping Weight 353 lbs.
(160kg)
419 lbs.
(419kg)
496 lbs.
(225kg)
Shipping Dimension (L x W x H) 20" x 32" x 55" 20" x 32" x 55" 20" x 36" x 75"
(.5 x .8 x 1.4m) (.5 x .8 x 1.4m) (.5 x .9 x 2.1m)
Standard Motor: 1800/3600 rpm
Spindle Speeds (rpm)
90-192-300-504-612-1020-1740-3360
E
G
F
D
A
H
A1
E
G
F
D
H
A
A1
C
E
F
D
I J I J
H
A
B B
G
B
Optional Cross Slide Table
Page 11
Optional Cross Slide Table
Page 12
SZ32
Clausing/Ibarmia Series Z32
Belt-drive Round Column Drills
With Manual or Mechanical Clutch
Select the Z series step pulley or variable speed belt-drive Industrial Drilling Machine that is right for the job. The SZ32 model is equipped with manual feed and step pulley drive and the AZ32V model is equipped with a mechanical clutch and mechanical variable speed drive.
Standard Features and Equipment:
• Drilling capacity in steel: up to 1.26"
(32mm) maximum
• Drilling capacity in cast iron: up to 1.38"
(35mm) maximum
• Tapping capacity in steel: up to .87"
(30mm) maximum
• Tapping capacity in cast iron: up to 1.18"
(30mm) maximum
• Automatic feed reversing system for tapping on “RS” models
• Machine base with 2 T-slots, coolant tank and pump
• Large work table with 3 T-slots
• Feed crank wheel for manual feed
• Depth scale and adjustable depth stop
• Automatic tool ejector
• Spindle reversing switch
• Work light
• Built-in low voltage electrical equipment in machine head
• Emergency STOP
• Drill guard with microswitch
Optional Equipment:
• Rotating Table
• Rotating Table and Ttilting Support
• Digital rpm Counter (for “V” Models)
• Union, Dragging Cone and Assembly for Multi-spindle Head
• Wheeled Base
• Cross Slide Table
• Cycle Start Foot Pedal
• Foot Pedal for Reversing
• Work Llight with Magnetic Base
• Coolant System with Independent Container
Optional Rotating Table
Capacities, Specifications and Dimensions:
Standard Models SZ32 AZ32V
Auto feed reversing for tapping models AZ32VRS
Capacities:
Maximum Drilling Capacity in Steel 1.26"
(32mm)
1.26"
(32mm)
Maximum Drilling Capacity in Cast Iron 1.38"
(35mm)
1.38"
(35mm)
Maximum Tapping Capacity in Steel .87"
(22mm)
.87"
(22mm)
Maximum Tapping Capacity in Cast Iron 1.18"
(30mm)
1.18"
(30mm)
Drill Head:
Spindle Taper 3MT 3MT
Quill Diameter 2.56"
(65mm)
2.56"
(65mm)
Spindle Travel (Drilling Depth) 5.91"
(150mm)
5.91"
(150mm)
Main Motor Power 1.2/1.8 hp
(.9/1.3kw)
1.2/1.8 hp
(.9/1.3kw)
Coolant Pump Motor Power .1 hp
(.07kw)
.1 hp
(.07kw)
Number of Speeds 10 Infinitely Variable
Number of Automatic Feeds - 2
Auto Feed Range: in./rev.
(mm/rev)
- .0039/.0079
(0.1-0.2)
Dimensions and Weights:
Height (A) 76.8"
(1950mm)
76.8"
(1950mm)
Base: Length x Width (B) 26.8" x 16.5"
(680 x 420mm)
26.8" x 16.5"
(680 x 420mm)
Base to Spindle (C) 50.59"
(1285mm)
50.59"
(1285mm)
Spindle Center to Column (D) 11.81"
(300mm)
11.81"
(300mm)
Spindle to Table (E)
Minimum 6.7"
(170mm)
6.7"
(170mm)
Maximum 32.87"
(835mm)
32.87"
(835mm)
Worktable: Length x Width (F) 15.75" x 18.9"
(400 x 480mm)
15.75" x 18.9"
(400 x 480mm)
Base Height (G) 4.72"
(120mm)
4.72"
(120mm)
Column Diameter (H) 4.92"
(125mm)
4.92"
(125mm)
Net Weight 573 lbs.
(260kg)
639 lbs.
(290kg)
Shipping Weight 683 lbs.
(310kg)
750 lbs.
(340kg)
Shipping Dimension (L x W x H) 24" x 44" x 91"
(.6 x 1.1 x 2.3m)
24" x 44" x 91"
(.6 x 1.1 x 2.3m)
E
F
D
Standard Motor: 2 Speed 900/1800 rpm
Model Spindle Speeds (rpm)
SZ32 900 rpm: 170-265-415-650-1035
1800 rpm: 340-530-830-1300-2070
AZ32V Infinitely Variable: 96-1405 rpm
Standard Fixed Table Models
Model Description
(Dimension See Page 29 )
1SZ32 23.6"
(600mm)
Drill with Fixed Table
1AZ32V 23.6"
(600mm)
Drill with Fixed Table
1AZ32VRS 23.6"
(600mm)
Drill with Fixed Table and Tapping System
C
H
A
G
B
“RS” models are equipped with automatic feed reversing system for tapping.
Page 13
Optional Cross Slide Table
Page 14
AZ40
Clausing/Ibarmia Series Z 34/40
Belt-drive Round Column Drills
With Manual, Mechanical Clutch or
Electromagnetic Clutch Feed Control
Select the Z series electronic variable speed belt-drive
Industrial Drilling Machine that is right for the job. SZ models are equipped with manual feed, AZ models are equipped with a mechanical clutch automatic feed control and the BZ models are equipped with electromagnetic automatic feed control.
Standard Features and Equipment:
• Drilling capacity in steel: up to 1.57"
(40mm) maximum
• Drilling capacity in cast iron: up to 1.77"
(45mm) maximum
• Tapping capacity in steel: up to 1.30"
(33mm) maximum
• Tapping capacity in cast iron: up to 1.54"
(39mm) maximum
• Automatic feed reversing system for tapping
• Digital rpm counter
• Machine base with 2 T-slots, coolant tank and pump
• Large rotating work table with 3 T-slots
• Feed crank wheel for manual feed
• Depth scale and adjustable depth stop
• Automatic tool ejector
• Spindle reversing switch
• Work light
• Built-in low voltage electrical equipment in machine head
• Emergency STOP
• Drill guard with microswitch
Optional Equipment:
• Rotating Table
• Rotating Table and Tilting Support
• Union, Dragging Cone and Assembly for Multi-spindle Head
• Wheeled Base
• Cross Slide Table
• Cycle Start Foot Pedal
• Foot Pedal for Reversing
• Work Light with Magnetic Base
• Coolant System with Independent Container
Optional Rotating Table
Capacities, Specifications and Dimensions:
Standard Models SZ/AZ/BZ34 SZ/AZ/BZ40
Capacities:
Maximum Drilling Capacity in Steel 1.34"
(34mm)
1.57"
(40mm)
Maximum Drilling Capacity in Cast Iron 1.57"
(40mm)
1.77"
(45mm)
Maximum Tapping Capacity in Steel 1.06"
(27mm)
1.30"
(33mm)
Maximum Tapping Capacity in Cast Iron 1.30"
(33mm)
1.54"
(39mm)
Drill Head:
Spindle Taper 4MT 4MT
Quill Diameter 2.95"
(75mm)
2.95"
(75mm)
Spindle Travel (Drilling Depth) 5.9"
(150mm)
7.09"
(180mm)
Main Motor Power 3 hp
(2.2kw)
4 hp
(3kw)
Coolant Pump Motor Power .1 hp
(.07kw)
.1 hp
(.07kw)
Spindle Speeds (Electronic Variable Speed) 100-2000 rpm 100-2000 rpm
Number of Automatic Feeds 3 3
Auto Feed Range: in./rev.
(mm/rev)
.0039/.0079/.0118
(0.1-0.2-0.3)
.0039/.0079/.0118
(0.1-0.2-0.3)
Dimensions and Weights:
Height (A) 76.5"
(1945mm)
76.8"
(1950mm)
Base: Length x Width (B) 29.1" x 16.2"
(740 x 412mm)
31.5" x 18.8"
(800 x 476mm)
Base to Spindle (C) 48.4"
(1230mm)
48.4"
(1230mm)
Spindle Center to Column (D) 11.81"
(300mm)
13.78"
(350mm)
Spindle to Table (E)
Minimum 1.97"
(50mm)
1.97"
(50mm)
Maximum 28.5"
(725mm)
27.2"
(690mm)
Worktable: Length x Width (F) 15.75" x 18.9"
(400 x 480mm)
18.9" x 22.05"
(480 x 560mm)
Base Height (G) 4.72"
(120mm)
4.72"
(120mm)
Column Diameter (H) 4.92"
(125mm)
5.91"
(150mm)
Net Weight 794 lbs.
(360kg)
1,014 lbs.
(460kg)
Shipping Weight 904 lbs.
(410kg)
1,124 lbs.
(510kg)
Shipping Dimension (L x W x H) 92" x 24" x 42"
(2.34 x .61 x 1.06m)
92" x 24" x 42"
(2.34 x .61 x 1.06m)
C
E
F
D
H
A
Standard Motor: 1800 rpm
Model Spindle Speeds (rpm)
AZ34 Electronic Variable: 100-2000 rpm
AZ40 Electronic Variable: 100-2000 rpm
Optional Spindle Motors
Motor Speed Range
1800-3600 rpm 340-4140 rpm
Standard Fixed Table Models
Model Description
(Dimension see page 29)
1SZ34 23.6"
(600mm)
Drill with Fixed Table and Tapping System
1AZ34 23.6"
(600mm)
Drill with Fixed Table and Tapping System
1BZ34 23.6"
(600mm)
Drill with Fixed Table and Tapping System
1SZ40 23.6"
(600mm)
Drill with Fixed Table and Tapping System
1AZ40 23.6"
(600mm)
Drill with Fixed Table and Tapping System
1BZ40 23.6"
(600mm)
Drill with Fixed Table and Tapping System
G
B
Page 15
Optional Cross Slide Table
Page 16
AX32
Clausing/Ibarmia Series X32
Geared-drive Round Column Drills
With Manual or Mechanical Clutch
The X series range of easy to operate Industrial Drilling
Machines offer a variety of capacities and feeds.
Engineered for a long work life the X series drills are a great value. SX models are equipped with manual feed,
AX models are equipped with a mechanical clutch automatic feed control.
Standard Features and Equipment:
• Drilling capacity in steel: up to 1.26"
(32mm) maximum
• Drilling capacity in cast iron: up to 1.38"
(35mm) maximum
• Tapping capacity in steel: up to .87"
(18mm) maximum
• Tapping capacity in cast iron: up to 1.18"
(22mm) maximum
• Automatic feed reversing system for tapping on “RS” models
• Hardened and ground high quality steel gears
• Speed plate and selecting levers on front of head
• Gear box lubrication by automatic pump
• Machine base with 2 T-slots, coolant tank and pump
• Large work table with 3 T-slots
• Feed crank wheel for manual feed
• Depth scale and adjustable depth stop
• Automatic tool ejector
• Work light
• Built-in low voltage electrical equipment in machine head
• Emergency STOP
• Drill guard with microswitch
Optional Equipment:
• Rotating Table
• Rotating Table and Tilting Support
• Automatic Pitch Control Tapping with Single Speed Brake Motor
• Automatic Pitch Control Tapping with Pneumatic Rapid Approach
• Master Guide Spindle and Nut Set for Automatic Pitch Control Tapping
• Union, Dragging Cone and Assembly for Multi-spindle Heads
• Wheeled Base
• Cross Slide Table
• Cycle Start Foot Pedal • Foot Pedal for Reversing
• Work Light with Magnetic Base
• Coolant System with Independent Container
Optional Rotating Table
Capacities, Specifications and Dimensions:
Standard Models SX32 AX32
Auto feed reversing for tapping models SX32RS AX32RS
Capacities:
Maximum Drilling Capacity in Steel 1.26"
(32mm)
1.26"
(32mm)
Maximum Drilling Capacity in Cast Iron 1.38"
(35mm)
1.38"
(35mm)
Maximum Tapping Capacity in Steel .87"
(22mm)
.87"
(22mm)
Maximum Tapping Capacity in Cast Iron 1.18"
(30mm)
1.18"
(30mm)
Drill Head:
Spindle Taper 3MT 3MT
Quill Diameter 2.56"
(65mm)
2.56"
(65mm)
Spindle Travel (Drilling Depth) 5.91"
(150mm)
5.91"
(150mm)
Main Motor Power 1.5 hp
(1.1kw)
1.5 hp
(1.1kw)
Coolant Pump Motor Power .1 hp
(.07kw)
.1 hp
(.07kw)
Number of Speeds 9 9
Number of Automatic Feeds - 2
Auto Feed Range: in./rev.
(mm/rev)
- .0039/.0079
(0.1-0.2)
Dimensions and Weights:
Height (A) 87.4"
(2220mm)
87.4"
(2220mm)
Base: Length x Width (B) 26.8" x 16.5"
(680 x 420mm)
26.8" x 16.5"
(680 x 420mm)
Base to Spindle (C) 50.39"
(1280mm)
50.39"
(1280mm)
Spindle Center to Column (D) 11.81"
(300mm)
11.81"
(300mm)
Spindle to Table (E)
Minimum 5.71"
(145mm)
5.71"
(145mm)
Maximum 31.89"
(810mm)
31.89"
(810mm)
Worktable: Length x Width (F) 15.75" x 18.9"
(400 x 480mm)
15.75" x 18.9"
(400 x 480mm)
Base Height (G) 4.72"
(120mm)
4.72"
(120mm)
Column Diameter (H) 4.92"
(125mm)
4.92"
(125mm)
Net Weight 694 lbs.
(315kg)
728 lbs.
(330kg)
Shipping Weight 794 lbs.
(360kg)
827 lbs.
(375kg)
Shipping Dimension (L x W x H) 24" x 44" x 91"
(.6 x 1.1 x 2.3m)
24" x 44" x 91"
(.6 x 1.1 x 2.3m)
E
F
D H
A
Standard Motor: 1800 rpm
Spindle Speeds SX32, AX32
123-180-257-295-432-617-820-1200-1714 rpm
Optional Spindle Motors
Motor Speed Range
1200 rpm 63-1000 rpm
3600 rpm 250-3480 rpm
900/1800 rpm 63-1000 rpm
1800-3600 rpm 123-3428 rpm
Standard Fixed Table Models
Model Description
(Dimension See Page 29)
1SX32 23.6"
(600mm)
Drill with Fixed Table
1SX32RS 23.6"
(600mm)
Drill with Fixed Table and Tapping System
1AX32 23.6"
(600mm)
Drill with Fixed Table
1AX32RS 23.6"
(600mm)
Drill with Fixed Table and Tapping System
C
G
B
“RS” models are equipped with automatic feed reversing system for tapping.
Page 17
Optional Cross Slide Table
Page 18
BX34
Clausing/Ibarmia Series X 34/40
Geared-drive Round Column Drills
With Manual, Mechanical Clutch or
Electromagnetic Clutch Feed Control
The X series range of easy to operate Industrial Drilling
Machines offer a variety of capacities and feeds.
Engineered for a long work life the X series drills are a great value. SX models are equipped with manual feed,
AX models are equipped with a mechanical clutch automatic feed control and the BX models are equipped with electromagnetic automatic feed control.
Standard Features and Equipment:
• Drilling capacity in steel: up to 1.57"
(40mm) maximum
• Drilling capacity in cast iron: up to 1.77"
(45mm) maximum
• Tapping capacity in steel: up to 1.30"
(33mm) maximum
• Tapping capacity in cast iron: up to 1.54"
(39mm) maximum
• Automatic feed reversing system for tapping on “RS” models
• Hardened and ground high quality steel gears
• Speed plate and selecting levers on front of head
• Gear box lubrication by automatic pump
• Machine base with 2 T-slots, coolant tank and pump
• Large rotating work table with 3 T-slots
• Feed crank wheel for manual feed
• Depth scale and adjustable depth stop
• Automatic tool ejector
• Work light
• Built-in low voltage electrical equipment in machine head
• Emergency STOP
• Drill guard with microswitch
Optional Equipment:
• Rotating Table and Tilting Support
• Automatic Pitch Control Tapping with Single Speed Brake Motor
• Automatic Pitch Control Tapping with Pneumatic Rapid Approach
• Master Guide Spindle and Nut Set for Automatic Pitch Control Tapping
• Union, Dragging Cone and Assembly for Multi-spindle Heads
• Wheeled Base
• Cross Slide Table • Cycle Start Foot Pedal
• Foot Pedal for Reversing • Work Light with Magnetic Base
• Coolant System with Independent Container
Optional Rotating Table
Capacities, Specifications and Dimensions:
Standard Models SX/AX/BX34 SX/AX/BX40
Auto feed reversing for tapping models SX/AX/BX34RS SX/AX/BX40RS
Capacities:
Maximum Drilling Capacity in Steel 1.34"
(34mm)
1.57"
(40mm)
Maximum Drilling Capacity in Cast Iron 1.57"
(40mm)
1.77"
(45mm)
Maximum Tapping Capacity in Steel 1.06"
(27mm)
1.30"
(33mm)
Maximum Tapping Capacity in Cast Iron 1.30"
(33mm)
1.54"
(39mm)
Drill Head:
Spindle Taper 4MT 4MT
Quill Diameter 2.95"
(75mm)
2.95"
(75mm)
Spindle Travel (Drilling Depth) 5.9"
(150mm)
7.09"
(180mm)
Main Motor Power 2 hp
(1.5kw)
3 hp
(2.2kw)
Coolant Pump Motor Power .1 hp
(.07kw)
.1 hp
(.07kw)
Number Speeds 9 9
Number of Automatic Feeds 3 3
Auto Feed Range: in./rev.
(mm/rev)
.0039/.0079/.0118
(0.1-0.2-0.3)
.0039/.0079/.0118
(0.1-0.2-0.3)
Dimensions and Weights:
Height (A) 86.4"
(2195mm)
90"
(2285mm)
Base: Length x Width (B) 29.1" x 16.2"
(740 x 412mm)
31.5" x 18.8"
(800 x 476mm)
Base to Spindle (C) 48.4"
(1230mm)
48.4"
(1230mm)
Spindle Center to Column (D) 11.81"
(300mm)
13.78"
(350mm)
Spindle to Table (E)
Minimum 1.97"
(50mm)
1.97"
(50mm)
Maximum 28.5"
(725mm)
27.2"
(690mm)
Worktable: Length x Width (F) 15.75" x 18.9"
(400 x 480mm)
18.9" x 22.05"
(480 x 560mm)
Base Height (G) 4.72"
(120mm)
4.72"
(120mm)
Column Diameter (H) 4.92"
(125mm)
5.91"
(150mm)
Net Weight 882 lbs.
(400kg)
1,081 lbs.
(490kg)
Shipping Weight 992 lbs.
(450kg)
1,190 lbs.
(540kg)
Shipping Dimension (L x W x H) 92" x 24" x 42"
(2.34 x .61 x 1.06m)
92" x 24" x 42"
(2.34 x .61 x 1.06m)
C
G
E
F
D
B
H
A
Standard Motor: 1800 rpm
Model
Spindle Speeds SX/AX/BX34 & SX/AX/BX40
158-233-332-383-559-799-1060-1555-2222 rpm
Standard Fixed Table Models
Model Description
(Dimension see page 29)
1SX34 23.6"
(600mm)
Drill with Fixed Table
1SX34RS 23.6"
(600mm)
Drill with Fixed Table and Tapping System
1AX34 23.6"
(600mm)
Drill with Fixed Table
1AX34RS 23.6"
(600mm)
Drill with Fixed Table and Tapping System
1BX34 23.6"
(600mm)
Drill with Fixed Table
1BX34RS 23.6"
(600mm)
Drill with Fixed Table and Tapping System
1SX40 27.5"
(700mm)
Drill with Fixed Table
1SX40RS 27.5"
(700mm)
Drill with Fixed Table and Tapping System
1AX40 27.5"
(700mm)
Drill with Fixed Table
1AX40RS 27.5"
(700mm)
Drill with Fixed Table and Tapping System
1BX40 27.5"
(700mm)
Drill with Fixed Table
1BX40RS 27.5"
(700mm)
Drill with Fixed Table and Tapping System
“RS” models are equipped with automatic feed reversing system for tapping.
Page 19
Optional Cross Slide Table
Page 20
A50
Clausing/Ibarmia Series A
Geared-drive Round Column Drills
With Mechanical Clutch Automatic Feed Control
The A series of Industrial Drilling Machines are capable of handling heavier workpieces with a wide range of drilling and tapping capacities. Designed for easy operation with a mechanical clutch for precise automatic feed control that can be activated from the feed crank handle or by the lever on the front of the machine head.
Standard Features and Equipment:
• Drilling capacity in steel: up to 1.97"
(50mm) maximum
• Drilling capacity in cast iron: up to 2.36"
(60mm) maximum
• Tapping capacity in steel: up to 1.42"
(36mm) maximum
• Tapping capacity in cast iron: up to 1.65"
(42mm) maximum
• Automatic feed reversing system for tapping
on “RS” models
• Automatic feed and cut-off by mechanical clutch
• Hardened and ground high quality steel gears
• Speed plate and selecting levers on front of head
• Gear box lubrication by automatic pump
• Machine base with 2 T-slots, coolant tank and pump
• Large rotating work table with 3 T-slots
• Feed crank wheel for manual feed
• Front hand wheel for fine feed work
• Depth scale and adjustable depth stop
• Automatic tool ejector
• Work light
• Built-in low voltage electrical equipment in machine head
• Emergency STOP
• Drill guard with microswitch
Optional Equipment:
• Rotating Table and Tilting Support
• Automatic Pitch Control Tapping with Single Speed Brake Motor
• Automatic Pitch Control Tapping with Pneumatic Rapid Approach
• Master Guide Spindle and Nut Set for Automatic Pitch
Control Tapping
• 50% Lower Feed Range
• Mechanical Spotface Device
• Pneumatic Counterbalance
• Multi-Spindle Head Guide Rod
• Union, Dragging Cone and Assembly for Multi-Spindle Head
• Multi-Spindle Head Guide Rod
• START-STOP and Emergency STOP Pendent Control
• 8"
(200mm)
Column Riser • Cross Slide Table
• Cycle Start Foot Pedal
• Foot Pedal for Reversing
• Work Light with Magnetic Base
• Coolant System with Independent Container
Capacities, Specifications and Dimensions:
Standard Models A40 A50
Auto feed reversing for tapping models A40RS A50RS
Capacities:
Maximum Drilling Capacity in Steel 1.38"
(35mm)
1.97"
(50mm)
Maximum Drilling Capacity in Cast Iron 1.77"
(45mm)
2.36"
(60mm)
Maximum Tapping Capacity in Steel 1"
(27mm)
1.42"
(36mm)
Maximum Tapping Capacity in Cast Iron 1.3"
(33mm)
1.65"
(42mm)
Drill Head:
Spindle Taper 4MT 4MT
Quill Diameter 2.95"
(75mm)
3.46"
(88mm)
Spindle Travel (Drilling Depth) 7.87"
(200mm)
9.06"
(230mm)
Main Motor Power 2 hp
(1.5kw)
4 hp
(3kw)
Coolant Pump Motor Power .1 hp
(.07kw)
.1 hp
(.07kw)
Number of Speeds 9 9
Number of Automatic Feeds 3 4
Auto Feed Range: in./rev.
(mm/rev)
.0039/.0079/.0118/
(0.1-0.2-0.3)
.0039/.0079/.0118/.0157/
(0.1-0.2-0.3-0.4)
Dimensions and Weights:
Height (A) 92.4"
(2390mm)
97.4"
(2475mm)
Base: Length x Width (B) 31.5" x 18.5"
(800x470mm)
33.9" x 21.7"
(860x550mm)
Base to Spindle (C) 47.24"
(1200mm)
51.18"
(1300mm)
Spindle Center to Column (D) 14.57"
(370mm)
14.57"
(370mm)
Spindle to Table (E)
Minimum 4.72"
(120mm)
5.91"
(150mm)
Maximum 30.71"
(780mm)
30.31"
(770mm)
Worktable: Length x Width (F) 18.9" x 22.1"
(480x560mm)
20.5" x 24.4"
(520x620mm)
Base Height (G) 4.72"
(120mm)
5.71"
(145mm)
Column Diameter (H) 6.3"
(160mm)
7.87"
(200mm)
Net Weight 1,080 lbs.
(490kg)
1,565 lbs.
(710kg)
Shipping Weight 1,257 lbs.
(570kg)
1,725 lbs.
(795kg)
Shipping Dimension (L x W x H) 28" x 40" x 95"
(.7 x 1 x 2.4m)
28" x 48" x 103"
(.7 x 1.2 x 2.6m )
E
F
D
A
Standard Motor: 1800 rpm
Model Spindle Speeds (rpm)
A40 73-103-149-232-325-472-695-976-1415
A50 66-91-133-206-288-418-617-856-1255
Standard Fixed Table Models
Model Description
(Dimension See Page 29)
1A40 29.5"
(750mm)
Drill with Fixed Table
1A40RS 29.5"
(750mm)
Drill with Fixed Table and Tapping
1A50 29.1"
(740mm)
Drill with Fixed Table
1A50RS 29.1"
(740mm)
Drill with Fixed Table and Tapping
Optional Spindle Motors
Model Motor Speed Range
A40 1200 rpm 50-948 rpm
A40 3600 rpm 146-2830 rpm
A40 900/1800 rpm 36-1415 rpm
A40 1800-3600 rpm 73-2830 rpm
A50 1200 rpm 46-878 rpm
A50 3600 rpm 132-2510 rpm
A50 900/1800 rpm 33-1255 rpm
A50 1800-3600 rpm 66-2510 rpm
C
H
G B
“RS” models are equipped with automatic feed reversing system for tapping.
Page 21
Optional Cross Slide Table
Page 22
B50
Clausing/Ibarmia Series B
Geared-drive Round Column Drills
With Push-button Electromagnetic Clutch
Automatic Feed Control
The B series is a rugged built Industrial Drilling
Machine designed to handle large workpieces and offers the widest range of large capacity drilling and tapping. The B series is equipped with an electromagnetic clutch for precise automatic feed control that can be activated from any of the 4 white push-buttons built into the end of the feed crank handles.
Standard Features and Equipment:
• Drilling capacity in steel: 2.75"
(70mm) maximum
• Drilling capacity in cast iron: 3.15"
(80mm) maximum
• Tapping capacity in steel: 2"
(50mm) maximum
• Tapping capacity in cast iron: 2.36"
(60mm) maximum
• Automatic feed reversing system for tapping on “RS” models
• Automatic feed and cut-off by electromagnetic clutch
• Hardened and ground high quality steel gears
• Speed plate and selecting levers on front of head
• Gear box lubrication by automatic pump
• Machine base with 2 T-slots, coolant tank and pump
• Large rotating work table with 3 T-slots
• Feed crank wheel for manual feed
• Front hand wheel for fine feed work
• Depth scale and adjustable depth stop
• Automatic tool ejector • Work light
• Built-in low voltage electrical equipment in machine head
• Emergency STOP • Drill guard with microswitch
Optional Equipment:
• Rotating Table and Tilting Support
• 8"
(200mm)
Column Riser
• Automatic Pitch Control Tapping with Single Speed Brake Motor
• Automatic Pitch Control Tapping with Pneumatic Rapid Approach
• Master Guide Spindle and Nut Set for Automatic Pitch
Control Tapping
• Pneumatic Counterbalance with Rapid Approach and Retract
• Pneumatic Counterbalance with Rapid Approach and Retract
for Tube and Profile Drilling
• Pneumatic Counterbalance with Rapid Approach and Retract
with Pitch Controlled Tapping
• 50% Lower Feed Range • Mechanical Spotface Device
• Pneumatic Counterbalance
• Multi-spindle Head Guide Rod
• Union, Dragging Cone and Assembly for Multi-spindle Head
• START-STOP and Emergency STOP Pendent Control
• Cross Slide Table • Work Light with Magnetic Base
• Cycle Start Foot Pedal • Foot Pedal for Reversing
• Coolant System with Independent Container
Capacities, Specifications and Dimensions:
Standard Models B40 B50 B60 B70
Auto feed reversing for tapping models B40RS B50RS B60RS B70RS
Capacities:
Maximum Drilling Capacity in Steel 1.57"
(40mm)
1.97"
(50mm)
2.36"
(60mm)
2.75"
(70mm)
Maximum Drilling Capacity in Cast Iron 2.17"
(50mm)
2.36"
(60mm)
2.75"
(70mm)
3.15"
(80mm)
Maximum Tapping Capacity in Steel 1.3"
(33mm)
1.42"
(36mm)
1.65"
(42mm)
2"
(50mm)
Maximum Tapping Capacity in Cast Iron 1.57"
(40mm)
1.65"
(42mm)
2"
(50mm)
2.36"
(60mm)
Drill Head:
Spindle Taper 4MT 4MT 5MT 5MT
Quill Diameter 3.46"
(88mm)
3.46"
(88mm)
3.54"
(90mm)
3.54"
(90mm)
Spindle Travel (Drilling Depth) 7.87"
(200mm)
9.06"
(230mm)
10.24"
(260mm)
10.24"
(260mm)
Main Motor Power 3 hp
(2.2kw)
4 hp
(3kw)
5.5 hp
(4kw)
7.5 hp
(5.5kw)
Coolant Pump Motor Power .1 hp
(.07kw)
.1 hp
(.07kw)
.12 hp
(.08kw)
.12 hp
(.08kw)
Number of Speeds (See Speed Charts) 9 9 12 12
Number of Automatic Feeds 4 6 6 6
.0039/.0079/.0118/.0157
(0.1-0.2-0.3-0.4)
.0039/.0079/.0118/.0157/.0197/.0236
(0.1-0.2-0.3-0.4-0.5-0.6)
Dimensions and Weights:
Height (A) 92.4"
(2390mm)
97.4"
(2475mm)
103.9"
(2640mm)
103.9"
(2640mm)
Base: Length x Width (B) 31.9" x 21.3"
(810x560mm)
33.9" x 21.7"
(860x550mm)
35.8" x 23.2"
(910x590mm)
35.8" x 23.2"
(910x590mm)
Base to Spindle (C) 49.61"
(1280mm)
51.18"
(1300mm)
49.21"
(1250mm)
49.21"
(1250mm)
Spindle Center to Column (D) 15.16"
(385mm)
14.57"
(370mm)
15.75"
(400mm)
15.75"
(400mm)
Spindle to Table (E)
Minimum 5.51"
(140mm)
5.91"
(150mm)
3.15"
(80mm)
3.15"
(80mm)
Maximum 30.71"
(780mm)
30.71"
(770mm)
25.98"
(660mm)
25.98"
(660mm)
Worktable: Length x Width (F) 18.9" x 22.1"
(480x560mm)
20.5" x 24.4"
(520x620mm)
23.6" x 27.6"
(600x700mm)
23.6" x 27.6"
(600x700mm)
Base Height (G) 5.31"
(135mm)
5.71"
(145mm)
6.3"
(160mm)
6.3"
(160mm)
Column Diameter (H) 7.09"
(180mm)
7.87"
(200mm)
8.66"
(220mm)
8.66"
(220mm)
Net Weight 1.345 lbs.
(610kg)
1,587 lbs.
(720kg)
1,808 lbs.
(820kg)
1,852 lbs.
(840kg)
Shipping Weight 1,532 lbs.
(695kg)
1,725 lbs.
(805kg)
2,025 lbs.
(920kg)
2,072 lbs.
(940kg)
Shipping Dimension (L x W x H) 28" x 40" x 103" 28" x 40" x 103" 32" x 52" x 111" 32" x 52" x 111"
(.7 x .1.2 x 2.6m) (.7 x .1.2 x 2.6m) (.8 x .1.3 x 2.8m) (.8 x .1.3 x 2.8m)
C
E
F
D
H
A
Standard Motor: 1800 rpm
Model Spindle speeds (rpm)
B40 73-103-149-232-325-472-695-976-1415
B50 66-91-133-206-288-418-617-866-1255
B60 76-96-127-165-238-296-392-513-670-838-1107-1446
B70 62-81-104-133-191-250-321-410-532-683-878-1120
Standard Fixed Table Models
Model Description
(Dimension see page 29)
1B40 29.5"
(750mm) with Drill Fixed Table
1B40RS 29.5"
(750mm) with Drill Fixed Table and Tapping
1B50 29.1"
(740mm) with Drill Fixed Table
1B50RS 29.1"
(740mm) with Drill Fixed Table and Tapping
Optional Spindle Motors
Model Motor Speed Range
B40 1200 rpm 50-948 rpm
B40 3600 rpm 146-2830 rpm
B40 900/1800 rpm 36-1415 rpm
B40 1800-3600 rpm 73-2830 rpm
B50 1200 rpm 46-878 rpm
B50 3600 rpm 132-2510 rpm
B50 900/1800 rpm 33-1255 rpm
B50 1800-3600 rpm 66-2510 rpm
B60 1200 rpm 54-1012 rpm
B60 3600 rpm 152-2892 rpm
B60 900/1800 rpm 38-1446 rpm
B60 1800-3600 rpm 76-2892 rpm
B70 1200 rpm 40-748 rpm
B70 3600 rpm 124-2440 rpm
B70 900/1800 rpm 31-1120 rpm
B70 1800/3600 rpm 62-2240 rpm
G
B
“RS” models are equipped with automatic feed reversing system for tapping.
Page 23
Optional Cross Slide Table
Page 24
BC50VE
Clausing/Ibarmia Series C
Belt/Geared-drive Round Column Drills
With Push-button Electromagnetic Clutch
Automatic Feed Control
The C series of Industrial Drilling Machines are capable of handling heavier workpieces with a wide range of drilling and tapping capacities. Designed for easy operation with an electromagnetic clutch for precise automatic feed control that can be activated from the feed crank handle or by the lever on the front of the machine head.
Standard Features and Equipment:
• Drilling capacity in steel: 1.97"
(50mm) maximum
• Drilling capacity in cast iron: 2.36"
(60mm) maximum
• Tapping capacity in steel: 1.68"
(42mm) maximum
• Tapping capacity in cast iron: 2"
(50mm) maximum
• Automatic feed reversing system for tapping
• Automatic feed and cut-off by electromagnetic clutch
• Hardened and ground high quality steel gears
• Speed plate and selecting levers on front of head
• Gear box lubrication by automatic pump
• Machine base with 2 T-slots, coolant tank and pump
• Large rotating work table with 3 T-slots
• Feed crank wheel for manual feed
• Front hand wheel for fine feed work
• Depth scale and adjustable depth stop
• Automatic tool ejector • Work light
• Built-in low voltage electrical equipment in machine head
• Emergency STOP • Drill guard with microswitch
Optional Equipment:
• Rotating Table and Tilting Support
• 8"
(203mm)
Column Riser
• Automatic Pitch Control Tapping with Single Speed Brake Motor
• Automatic Pitch Control Tapping with Pneumatic Rapid Approach
• Master Guide Spindle and Nut Set for Automatic Pitch
Control Tapping
• Pneumatic Counterbalance with Rapid Approach and Retract
• Pneumatic Counterbalance with Rapid Approach and Retract
for Tube and Profile Drilling
• Pneumatic Counterbalance with Rapid Approach and Retract
with Pitch Controlled Tapping
• 50% Lower Feed Range
• Mechanical Spotface Device
• Pneumatic Counterbalance
• Multi-Spindle Head Guide Rod
• Union, Dragging Cone and Assembly for Multi-Spindle Head
• START/STOP and Emergency STOP Pendent Control
• Cross Slide Table • Work Light with Magnetic Base
• Cycle Start Foot Pedal • Foot Pedal for Reversing
• Coolant System with Independent Container
Capacities, Specifications and Dimensions:
Standard Models BC40V BC40VE BC50V BC50VE
Capacities:
Maximum Drilling Capacity in Steel 1.57"
(40mm)
1.57"
(40mm)
1.97"
(50mm)
1.97"
(50mm)
Maximum Drilling Capacity in Cast Iron 1.97"
(50mm)
1.97"
(50mm)
2.36"
(60mm)
2.36"
(60mm)
Maximum Tapping Capacity in Steel 1.42"
(36mm)
1.42"
(36mm)
1.65"
(36mm)
1.65"
(36mm)
Maximum Tapping Capacity in Cast Iron 1.65"
(36mm)
1.65"
(36mm)
1.97 "
(50mm)
1.97"
(50mm)
Drill Head:
Spindle Taper 4MT 4MT 4MT 4MT
Quill Diameter 3.46"
(87.9mm)
3.46"
(87.9mm)
3.46"
(87.9mm)
3.46"
(87.9mm)
Spindle Travel (Drilling Depth) 7.87"
(200mm)
7.87"
(200mm)
7.87"
(200mm)
7.87"
(200mm)
Main Motor Power 4 hp
(3kw)
4 hp
(3kw)
5.5 hp
(4kw)
5.5 hp
(4kw)
Coolant Pump Motor Power .1 hp
(.07 kw)
.1 hp
(.07kw)
.1 hp
(.07kw)
.1 hp
(.07kw)
No. of Variable Speeds Ranges and Type 3 mechanical 3 electronic 3 mechanical 3 electronic
Low Range (rpm) 72-240 30-230 72-240 30-230
Med Range (rpm) 240-720 90-730 240-720 90-730
High Range (rpm) 720-2200 190-1500 720-2200 190-1500
Number of Automatic Feeds 4 4 4 4
Auto Feed Range .0039/.0079/.118/.157 (in./rev.)
(0.1/0.2/0.3/0.4 mm/rev)
Dimensions and Weights:
Height (A) 81.9"
(2080mm)
81.9"
(2080mm)
83.5"
(2120mm)
83.5"
(2120mm)
Base: Length x Width (B) 31.9" x 26.3"
(810 x 540mm)
31.9" x 26.3"
(810 x 540mm)
33.9" x 21.7"
(860 x 550mm)
33.9" x 21.7"
(860 x 550mm)
Base to Spindle (C) 46.1"
(1170mm)
46.1"
(1170mm)
49"
(1246mm)
49"
(1246mm)
Spindle Center to Column (D) 15.15"
(385mm)
15.15"
(385mm)
14.56"
(370mm)
14.56"
(370mm)
Spindle to Table (E
Minimum 1.97"
(50mm)
1.97"
(50mm)
1.57"
(40mm)
1.57"
(40mm)
Maximum 27.16"
(690mm)
27.16"
(690mm)
26"
(660mm)
26"
(660mm)
Worktable: Length x Width (F) 18.9" x 22"
(480 x 560mm)
18.9" x 22"
(480 x 560mm)
20.5" x 24.4"
(520 x 620mm)
20.5" x 24.4"
(520 x 620mm)
Base Height (G) 5.31"
(135mm)
5.31"
(135mm)
5.71"
(145mm)
5.71"
(145mm)
Column Diameter (H) 7.09"
(180mm)
7.09"
(180mm)
7.87"
(200mm)
7.87"
(200mm)
Net Weight 1,455 lbs.
(660kg)
1,455 lbs.
(660kg)
1,675 lbs.
(760kg)
1,675 lbs.
(760kg)
Shipping Weight 1,653 lbs.
(750kg)
1,653 lbs.
(750kg)
1,874 lbs.
(850kg)
1,874 lbs.
(850kg)
Shipping Dimension (L x W x H) 32" x 51" x 91"
(.8 x 1.3 x 2.3m)
36" x 55" x 91"
(.9 x 1.4 x 2.3m)
Standard Motor: 1800 rpm
Model Spindle Speeds (rpm)
BC40V Mechanical Variable Speed: 72-1800 rpm
BC50V Mechanical Variable Speed: 36-1800 rpm
BC40VE Electronic Variable Speed: 72-1800 rpm
BC50VE Electronic Variable Speed: 36-1800 rpm
Standard Fixed Table Models
Model Description
1BC40V 30.3"
(770mm)
Drill with Fixed Table
1BC50V 29"
(736mm)
Drill with Fixed Table
1BC40VE 30.3"
(770mm)
Drill with Fixed Table
1BC50VE 29"
(736mm)
Drill with Fixed Table
Page 25
Clausing/Ibarmia Multi Head, Fixed Table and Oversized Table Drills
Clausing Ibarmia Industrial Drilling Machines mounted to a fixed or oversized table offer greater ease in positioning the workpiece and the flexibility to handle bulky or heavy workpieces.
Multiple Head drilling machines are ideal for work where the workpiece requires more than one operation. Each drill head on a multiple head drill can be equipped differently to perform the operation required by that head such as... automatic drilling cycle, automatic tapping or other options that may be offered. Drilling machines can be set -up with rotating heads adding flexibility.
3AX32 23.6 "
(600mm)
Geared-drive 3 head drill.
3AX32
Multiple Spindle Dimensional Drawings
N
1B50
1B50 29.1"
(740mm)
Geared-drive drill mounted to standard fixed table.
N N N N
E
F
D H
A
C
B
E
F
D
C
H
A
B
L
M
Page 26
Multiple Spindle Models, Size and Dimensions:
Models Size A B C D E F H L M N
min. max.
Fixed Table Drills
(Includes RS Models)
1SZ32, 1AZ32V 19.7"
(500mm)
89.6"
(2275mm)
35.8"
(910mm)
35.4"
(900mm)
11.8"
(300mm)
9.8"
(250mm)
32.6"
(830mm)
15.7"
(400mm)
4.9"
(125mm)
15.7"
(400mm)
23.6"
(600mm)
-
1SZ34, 1AZ34, 1BZ34 23.6"
(600mm)
87.8"
(2230mm)
35.8"
(910mm)
35.4"
(900mm)
11.8"
(300mm)
7.8"
(200mm)
29.1"
(740mm)
15.7"
(400mm)
4.9"
(125mm)
15.7"
(400mm)
23.6"
(600mm)
-
1SZ40, 1AZ40, 1BZ40 27.1"
(690mm)
88.6"
(2230mm)
40.8"
(1035mm)
35.4"
(900mm)
13.5"
(345mm)
7.8"
(200mm)
28.1"
(715mm)
16.7"
(500mm)
6.3"
(160mm)
23.6"
(600mm)
31.5"
(800mm)
-
1SX32, 1AX32 23.6"
(600mm)
100"
(2540mm)
35.8"
(910mm)
35.4"
(900mm)
11.8"
(300mm)
8.6"
(220mm)
31.5"
(800mm)
15.7"
(400mm)
4.9"
(125mm)
15.7"
(400mm)
23.6"
(600mm)
-
1SX34, 1AX34, 1BX34 23.6"
(600mm)
97.6"
(2480mm)
35.8"
(910mm)
35.4"
(900mm)
11.8"
(300mm)
7.8"
(200mm)
29.1"
(740mm)
15.7"
(400mm)
4.9"
(125mm)
15.7"
(400mm)
23.6"
(600mm)
-
1SX40, 1AX40, 1BX40 27.1"
(690mm)
100.4"
(2550mm)
40.8"
(1035mm)
35.4"
(900mm)
13.5"
(345mm)
7.8"
(200mm)
28.1"
(715mm)
19.6"
(500mm)
6.3"
(160mm)
23.6"
(600mm)
31.5"
(800mm)
-
1A40, 1B40 29.5"
(750mm)
107.1"
(2720mm)
43.7"
(1110mm)
35.4"
(900mm)
14.7"
(375mm)
9.8"
(250mm)
32.6"
(830mm)
19.6"
(500mm)
7.8"
(200mm)
23.6"
(600mm)
31.5"
(800mm)
-
1A50, 1B50 29.1"
(740mm)
108.3"
(2750mm)
43.5"
(1105mm)
35.4"
(900mm)
14.5"
(370mm)
9.8"
(250mm)
32.6"
(830mm)
19.6"
(500mm)
7.8"
(200mm)
23.6"
(600mm)
31.5"
(800mm) -
2 Head Drills
2SZ32, 2AZ32 23.6"
(600mm)
89.6"
(2275mm)
35.8"
(910mm)
35.4"
(900mm)
11.8"
(300mm)
9.8"
(250mm)
32.6"
(830mm)
11.8"
(300mm)
4.9"
(125mm)
35.4"
(900mm)
43.3"
(1100mm)
19.7"
(500mm)
2SZ34, 2AZ34, 2BZ34 23.6"
(600mm)
87.8"
(2230mm)
35.8"
(910mm)
35.4"
(900mm)
11.8"
(300mm)
7.8"
(200mm)
29.1"
(740mm)
11.8"
(300mm)
4.9"
(125mm)
35.4"
(900mm)
43.3"
(1100mm)
19.7"
(500mm)
2SZ40, 2AZ40, 2BZ40 27.1"
(690mm)
88.6"
(2230mm)
40.8"
(1035mm)
35.4"
(900mm)
13.5"
(345mm)
7.8"
(200mm)
28.1"
(715mm)
15.7"
(400mm)
6.3"
(160mm)
37.4"
(950mm)
45.3"
(1150mm)
21.6"
(550mm)
2SX32, 2AX32 23.6"
(600mm)
100"
(2540mm)
35.8"
(910mm)
35.4"
(900mm)
11.8"
(300mm)
8.6"
(220mm)
31.5"
(800mm)
11.8"
(300mm)
4.9"
(125mm)
35.4"
(900mm)
43.3"
(1100mm)
19.7"
(500mm)
2SX34, 2AX34, 2BX34 23.6"
(600mm)
97.6"
(2480mm)
35.8"
(910mm)
35.4"
(900mm)
11.8"
(300mm)
7.8"
(200mm)
29.1"
(740mm)
11.8"
(300mm)
4.9"
(125mm)
35.4"
(900mm)
43.3"
(1100mm)
19.7"
(500mm)
2SX40, 2AX40, 2BX40 27.1"
(690mm)
100.4"
(2550mm)
40.8"
(1035mm)
35.4"
(900mm)
13.5"
(345mm)
7.8"
(200mm)
28.1"
(715mm)
15.7"
(400mm)
6.3"
(160mm)
37.4"
(950mm)
45.3"
(1150mm)
21.6"
(550mm)
2A40, 2B40 29.5"
(750mm)
107.1"
(2720mm)
43.7"
(1110mm)
35.4"
(900mm)
14.7"
(375mm)
9.8"
(250mm)
32.6"
(830mm)
15.7"
(400mm)
7.8"
(200mm)
37.4"
(950mm)
45.3"
(1150mm)
21.6"
(550mm)
2A50, 2B50 29.1"
(740mm)
108.3"
(2750mm)
43.5"
(1105mm)
35.4"
(900mm)
14.5"
(370mm)
9.8"
(250mm)
32.6"
(830mm)
15.7"
(400mm)
7.8"
(200mm)
37.4"
(950mm)
45.3"
(1150mm)
21.6"
(550mm)
3 Head Drills
3SZ32, 3AZ32V 23.6"
(600mm)
89.6"
(2275mm)
35.8"
(910mm)
35.4"
(900mm)
11.8"
(300mm)
9.8"
(250mm)
32.6"
(830mm)
11.8"
(300mm)
4.9"
(125mm)
55.1"
(1400mm)
63"
(1600mm)
19.7"
(500mm)
3SZ34, 3AZ34, 3BZ34 23.6"
(600mm)
87.8"
(2230mm)
35.8"
(910mm)
35.4"
(900mm)
11.8"
(300mm)
7.8"
(200mm)
29.1"
(740mm)
11.8"
(300mm)
4.9"
(125mm)
55.1"
(1400mm)
63"
(1600mm)
19.7"
(500mm)
3SZ40, 3AZ40, 3BZ40 27.1"
(690mm)
88.6"
(2230mm)
40.8"
(1035mm)
35.4"
(900mm)
13.5"
(345mm)
7.8"
(200mm)
28.1"
(715mm)
15.7"
(400mm)
6.3"
(160mm)
59.1"
(1500mm)
67"
(1700mm)
21.6"
(550mm)
3SX32, 3AX32 23.6"
(600mm)
100"
(2540mm)
35.8"
(910mm)
35.4"
(900mm)
11.8"
(300mm)
8.6"
(220mm)
31.5"
(800mm)
11.8"
(300mm)
4.9"
(125mm)
55.1"
(1400mm)
63"
(1600mm)
19.7"
(500mm)
3SX34, 3AX34, 3BX34 23.6"
(600mm)
97.6"
(2480mm)
35.8"
(910mm)
35.4"
(900mm)
11.8"
(300mm)
7.8"
(200mm)
29.1"
(740mm)
11.8"
(300mm)
4.9"
(125mm)
55.1"
(1400mm)
63"
(1600mm)
19.7"
(500mm)
3SX40, 3AX40, 3BX40 27.1"
(690mm)
100.4"
(2550mm)
40.8"
(1035mm)
35.4"
(900mm)
13.5"
(345mm)
7.8"
(200mm)
28.1"
(715mm)
15.7"
(400mm)
6.3"
(160mm)
59.1"
(1500mm)
67"
(1700mm)
21.6"
(550mm)
3A40, 3B40 29.5"
(750mm)
107.1"
(2720mm)
43.7"
(1110mm)
35.4"
(900mm)
14.7"
(375mm)
9.8"
(250mm)
32.6"
(830mm)
15.7"
(400mm)
7.8"
(200mm)
59.1"
(1500mm)
67"
(1700mm)
21.6"
(550mm)
3A50, 3B50 29.1"
(740mm)
108.3"
(2750mm)
43.5"
(1105mm)
35.4"
(900mm)
14.5"
(370mm)
9.8"
(250mm)
32.6"
(830mm)
15.7"
(400mm)
7.8"
(200mm)
59.1"
(1500mm)
67"
(1700mm)
21.6"
(550mm)
4 Head Drills
4SZ32, 4AZ32 23.6"
(600mm)
89.6"
(2275mm)
35.8"
(910mm)
35.4"
(900mm)
11.8"
(300mm)
9.8"
(250mm)
32.6"
(830mm)
11.8"
(300mm)
4.9"
(125mm)
75"
(1900mm)
82.6"
(2100mm)
19.7"
(500mm)
4SZ34, 4AZ34, 4BZ34 23.6"
(600mm)
87.8"
(2230mm)
35.8"
(910mm)
35.4"
(900mm)
11.8"
(300mm)
7.8"
(200mm)
29.1"
(740mm)
11.8"
(300mm)
4.9"
(125mm)
75"
(1900mm)
82.6"
(2100mm)
19.7"
(500mm)
4SZ40, 4AZ40, 4BZ40 27.1"
(690mm)
88.6"
(2230mm)
40.8"
(1035mm)
35.4"
(900mm)
13.5"
(345mm)
7.8"
(200mm)
28.1"
(715mm)
15.7"
(400mm)
6.3"
(160mm)
80.7"
(2050mm)
88.5"
(2250mm)
21.6"
(550mm)
4SX32, 4AX32 23.6"
(600mm)
100"
(2540mm)
35.8"
(910mm)
35.4"
(900mm)
11.8"
(300mm)
8.6"
(220mm)
31.5"
(800mm)
11.8"
(300mm)
4.9"
(125mm)
75"
(1900mm)
82.6"
(2100mm)
19.7"
(500mm)
4SX34, 4AX34, 4BX34 23.6"
(600mm)
97.6"
(2480mm)
35.8"
(910mm)
35.4"
(900mm)
11.8"
(300mm)
7.8"
(200mm)
29.1"
(740mm)
11.8"
(300mm)
4.9"
(125mm)
75"
(1900mm)
82.6"
(2100mm)
19.7"
(500mm)
4SX40, 4AX40, 4BX40 27.1"
(690mm)
100.4"
(2550mm)
40.8"
(1035mm)
35.4"
(900mm)
13.5"
(345mm)
7.8"
(200mm)
28.1"
(715mm)
15.7"
(400mm)
6.3"
(160mm)
80.7"
(2050mm)
88.5"
(2250mm)
21.6"
(550mm)
4A40, 4B40 29.5"
(750mm)
107.1"
(2720mm)
43.7"
(1110mm)
35.4"
(900mm)
14.7"
(375mm)
9.8"
(250mm)
32.6"
(830mm)
15.7"
(400mm)
7.8"
(200mm)
80.7"
(2050mm)
88.5"
(2250mm)
21.6"
(550mm)
4A50, 4B50 29.1"
(740mm)
108.3"
(2750mm)
43.5"
(1105mm)
35.4"
(900mm)
14.5"
(370mm)
9.8"
(250mm)
32.6"
(830mm)
15.7"
(400mm)
7.8"
(200mm)
80.7"
(2050mm)
88.5"
(2250mm)
21.6"
(550mm)
5 Head Drills
5SZ32, 5AZ32 23.6"
(600mm)
89.6"
(2275mm)
35.8"
(910mm)
35.4"
(900mm)
11.8"
(300mm)
9.8"
(250mm)
32.6"
(830mm)
11.8"
(300mm)
4.9"
(125mm)
94.5"
(2400mm)
102.4"
(2600mm)
19.7"
(500mm)
5SZ34, 5AZ34, 5BZ34 23.6"
(600mm)
87.8"
(2230mm)
35.8"
(910mm)
35.4"
(900mm)
11.8"
(300mm)
7.8"
(200mm)
29.1"
(740mm)
11.8"
(300mm)
4.9"
(125mm)
94.5"
(2400mm)
102.4"
(2600mm)
19.7"
(500mm)
5SZ40, 5AZ40, 5BZ40 27.1"
(690mm)
88.6"
(2230mm)
40.8"
(1035mm)
35.4"
(900mm)
13.5"
(345mm)
7.8"
(200mm)
28.1"
(715mm)
15.7"
(400mm)
6.3"
(160mm)
102.4"
(2600mm)
110.2"
(2800mm)
21.6"
(550mm)
5SX32, 5AX32 23.6"
(600mm)
100"
(2540mm)
35.8"
(910mm)
35.4"
(900mm)
11.8"
(300mm)
8.6"
(220mm)
31.5"
(800mm)
11.8"
(300mm)
4.9"
(125mm)
94.5"
(2400mm)
102.4"
(2600mm)
19.7"
(500mm)
5SX34, 5AX34, 5BX34 23.6"
(600mm)
97.6"
(2480mm)
35.8"
(910mm)
35.4"
(900mm)
11.8"
(300mm)
7.8"
(200mm)
29.1"
(740mm)
11.8"
(300mm)
4.9"
(125mm)
94.5"
(2400mm)
102.4"
(2600mm)
19.7"
(500mm)
5SX40, 5AX40, 5BX40 27.1"
(690mm)
100.4"
(2550mm)
40.8"
(1035mm)
35.4"
(900mm)
13.5"
(345mm)
7.8"
(200mm)
28.1"
(715mm)
15.7"
(400mm)
6.3"
(160mm)
102.4"
(2600mm)
110.2"
(2800mm)
21.6"
(550mm)
5A40, 5B40 29.5"
(750mm)
107.1"
(2720mm)
43.7"
(1110mm)
35.4"
(900mm)
14.7"
(375mm)
9.8"
(250mm)
32.6"
(830mm)
15.7"
(400mm)
7.8"
(200mm)
102.4"
(2600mm)
110.2"
(2800mm)
21.6"
(550mm)
5A50, 5B50 29.1"
(740mm)
108.3"
(2750mm)
43.5"
(1105mm)
35.4"
(900mm)
14.5"
(370mm)
9.8"
(250mm)
32.6"
(830mm)
15.7"
(400mm)
7.8"
(200mm)
102.4"
(2600mm)
110.2"
(2800mm)
21.6"
(550mm)
6 Head Drills
6SZ32, 6AZ32 23.6"
(600mm)
89.6"
(2275mm)
35.8"
(910mm)
35.4"
(900mm)
11.8"
(300mm)
9.8"
(250mm)
32.6"
(830mm)
11.8"
(300mm)
4.9"
(125mm)
114"
(2900mm)
122"
(3100mm)
19.7"
(500mm)
6SZ34, 6AZ34, 6BZ34 23.6"
(600mm)
87.8"
(2230mm)
35.8"
(910mm)
35.4"
(900mm)
11.8"
(300mm)
7.8"
(200mm)
29.1"
(740mm)
11.8"
(300mm)
4.9"
(125mm)
114"
(2900mm)
122"
(3100mm)
19.7"
(500mm)
6SZ40, 6AZ40, 6BZ40 27.1"
(690mm)
88.6"
(2230mm)
40.8"
(1035mm)
35.4"
(900mm)
13.5"
(345mm)
7.8"
(200mm)
28.1"
(715mm)
15.7"
(400mm)
6.3"
(160mm)
124"
(3150mm)
132"
(3350mm)
21.6"
(550mm)
6SX32, 6AX32 23.6"
(600mm)
100"
(2540mm)
35.8"
(910mm)
35.4"
(900mm)
11.8"
(300mm)
8.6"
(220mm)
31.5"
(800mm)
11.8"
(300mm)
4.9"
(125mm)
114"
(2900mm)
122"
(3100mm)
19.7"
(500mm)
6SX34, 6AX34, 6BX34 23.6"
(600mm)
97.6"
(2480mm)
35.8"
(910mm)
35.4"
(900mm)
11.8"
(300mm)
7.8"
(200mm)
29.1"
(740mm)
11.8"
(300mm)
4.9"
(125mm)
114"
(2900mm)
122"
(3100mm)
19.7"
(500mm)
6SX40, 6AX40, 6BX40 27.1"
(690mm)
100.4"
(2550mm)
40.8"
(1035mm)
35.4"
(900mm)
13.5"
(345mm)
7.8"
(200mm)
28.1"
(715mm)
15.7"
(400mm)
6.3"
(160mm)
124"
(3150mm)
132"
(3350mm)
21.6"
(550mm)
6A40, 6B40 29.5"
(750mm)
107.1"
(2720mm)
43.7"
(1110mm)
35.4"
(900mm)
14.7"
(375mm)
9.8"
(250mm)
32.6"
(830mm)
15.7"
(400mm)
7.8"
(200mm)
124"
(3150mm)
132"
(3350mm))
21.6"
(550mm)
6A50, 6B50 29.1"
(740mm)
108.3"
(2750mm)
43.5"
(1105mm)
35.4"
(900mm)
14.5"
(370mm)
9.8"
(250mm)
32.6"
(830mm)
15.7"
(400mm)
7.8"
(200mm)
124"
(3150mm)
132"
(3350mm)
21.6"
(550mm)
Page 27
Clausing/Ibarmia Round Column
Drill Optional Equipment
Model Description:
7044 Coolant System with Separate Tank (all models)
7022 Work Light with Magnetic Base (all models)
PST Cycle or Spindle turn START Foot Pedal
PSR Spindle Reverse Foot Pedal (for tapping)
MCC-KT Cross Slide Table 13.8" x 10.8" (K/T Series)
MCC-ZX Cross Slide Table 15" x 8.7" (Z/X Series)
MCC-X40 Cross Slide Table 15" x 8.7" (X40 Series)
MB-5D Cross Slide Table 16" x 12" (X Model A/B Series)
Series T
(Factory Installed Only)
MG-T Rotating Table
PKA Floor Cabinet with 2 Shelves
PKB Floor Cabinet with Door and Drawer
Series Z
(Factory Installed Only)
MG-Z Rotating Table
MGI-Z Tilting Rotating Table
TAK-Z Digital rpm Read-out (V Models only)
UC-Z Union, Dragging Cone and Assembly for Multi-spindle Head
Series X
(Factory Installed Only)
MG-X Rotating Table (X32 Models)
MGI-X Tilting Rotating Table
RPF-X Automatic Pitch Controlled Tapping with Single Speed Brake-motor
RPF-ANR-X Automatic Pitch Controlled Tapping with Pneumatic Rapid Approach
HGP-X Master Guide Spindle and Nut Set for Automatic Pitch Controlled
Tapping
UC-X Union, Dragging Cone and Assembly for Multi-spindle Head
Series A/B
(Factory Installed Only)
RPF-A Automatic Pitch Controlled Tapping with Single Speed Brake-motor
RPF-ANR-A Automatic Pitch Controlled Tapping with Pneumatic Rapid Approach
HGP-A Master Guide Spindle and Nut Set for Automatic Pitch Controlled
Tapping
ACNL-B Pneumatic Counterbalance with Rapid Approach and Retreat
ACNL-S-B Pneumatic Counterbalance with Rapid Approach and Retreat for
Tube and Profile Drilling
ACNL-RPF-B Pneumatic Counterbalance with Rapid Approach and Retreat with
Controlled Tapping
AR-A 50% Lower Feed Rate Range
DLM-A Mechanical Spotface Device
CN-A Pneumatic Counterbalance for Spindle Return
UC-A Union, Dragging Cone and Assembly for Multi-Spindle Head
GM-A Multi-Spindle Head Guide Rod
PM-B START/STOP and Emergency Stop Pendent Control
SC-B 8" Column Riser
Page 28
Dimensions:
K
L
H
G
E
D
C
R x S
Capacities:
Model CL720A
Capacity:
Drilling
In Steel 1.26"
(32mm)
In Cast Iron 2"
(50mm)
Tapping
In Steel 1"
(25mm)
In Cast Iron 1.26"
(32mm)
Boring
In Steel 2.75"
(70mm)
In Cast Iron 4.06"
(105mm)
B
Q
A
F
Clausing Radial Drills
Models: CL720A
Features and Standard Equipment:
●
Limit switch
●
High speed gears are made of Nickel-Chrome Steel
and are heat-treated and ground for durability
●
Powerful 2 Hp spindle drive motor for heavy-duty
cutting
●
Extra auxiliary dial for spindle feed depth indication,
allows review of spindle feed depth, .0394" to 7.874"
●
Special spindle balance mechanism, superior to
traditional balance mechanism and extends Balance
Spring life
●
Coolant system
●
Low volt and overload protection
●
230/3/60 volt standard
●
Tool kit and manuals
Specifications:
Model CL720A
Working Area:
Column Sleeve Dia. (E) 8.28"
(210mm)
Column Face to Spindle Center
Maximum (D+C) 29.5"
(750mm)
Minimum (D) 8.7"
(220mm)
Spindle Head Travel (C) 20.8"
(530mm)
Base Surface to Spindle End
Maximum (A) 41.7"
(1060mm)
Minimum (B) 10.2"
(260mm)
Arm Vertical Travel (A-B) 31.5" (800mm)
Arm Rotation (Right & Left) 180°
Baseplate Working Surface 35.5" x 25.3"
(902x643mm)
Box Table Area
Length (L) 23.6"
(600mm)
Width (K) 17.5"
(445mm)
Height (H) 15"
(382mm)
Base Dimensions
Floor Area (R x S) 49.6" x
25.2"
(1260x640mm)
Height (Q) 6.5"
(163mm)
Drill Head:
Spindle Taper 4MT
Spindle Stroke 8.66"
(220mm)
Quill Diameter 2.95"
(75mm)
Number of Spindle Speeds 6
Spindle Speeds (rpm) 88, 154, 282, 455, 796, 1500
Number of Feeds 3
Spindle Feed Rate (in/rev.) 0.002"/0.0035"/0.006"
(mm/rev.) .05mm/.09mm/.15mm
Spindle Drive Motor 2 hp
(1.5 Kw)
Elevating Motor 1 hp
(.75 Kw)
Coolant Pump Motor 1/8 hp
(.10 Kw)
Dimensions and Weights:
Max. Machine Height (F) 85.4"
(2170mm)
Base and Column Height (G) 72.8"
(1850mm)
Shipping Dim.
Length 66.1"
(1680mm)
Width 32.5"
(826mm)
Height 85"
(2160mm)
Net Weight 2,469 lbs.
(1120kg)
Shipping Weight 2,756 lbs.
(1250kg)
Page 29
Dimensions:
K
L
H
G
E
D
C
R x S
Capacities:
Model CL820A
Capacity:
Drilling
In Steel 1.26"
(32mm)
In Cast Iron 2"
(50mm)
Tapping
In Steel 1"
(25mm)
In Cast Iron 1.26"
(32mm)
Boring
In Steel 2.75"
(70mm)
In Cast Iron 4.06"
(105mm)
Page 30
B
Q
A
F
Clausing Radial Drills
Models: CL820A
Features and Standard Equipment:
●
Limit switch
●
High speed gears are made of Nickel-Chrome Steel
and are heat-treated and ground for durability
●
Powerful 2 Hp spindle drive motor for heavy-duty
cutting
●
Extra auxiliary dial for spindle feed depth indication,
allows review of spindle feed depth, .0394" to 7.874"
●
Special spindle balance mechanism, superior to
traditional balance mechanism and extends Balance
Spring life
●
Coolant system
●
Low volt and overload protection
●
230/3/60 volt standard
●
Tool kit and manuals
Specifications:
Model CL820A
Working Area:
Column Sleeve Dia. (E) 8.28"
(210mm)
Column Face to Spindle Center
Maximum (D+C) 33.5"
(850mm)
Minimum (D) 8.7"
(220mm)
Spindle Head Travel (C) 24.8"
(630mm)
Base Surface to Spindle End
Maximum (A) 47.6"
(1270mm)
Minimum (B) 13.8"
(350mm)
Arm Vertical Travel (A-B) 33.8" (858mm)
Arm Rotation (Right & Left) 180°
Baseplate Working Surface 35.5" x 25.3"
(902x643mm)
Box Table Area
Length (L) 23.6"
(600mm)
Width (K) 17.5"
(445mm)
Height (H) 15"
(382mm)
Base Dimensions
Floor Area (R x S) 49.6" x
25.2"
(1260x640mm)
Height (Q) 6.5"
(163mm)
Drill Head:
Spindle Taper 4MT
Spindle Stroke 8.66"
(220mm)
Quill Diameter 2.95"
(75mm)
Number of Spindle Speeds 6
Spindle Speeds (rpm) 88, 154, 282, 455, 796, 1500
Number of Feeds 3
Spindle Feed Rate (in/rev.) 0.002" 0.0035" 0.006"
.05mm)
,
(.09mm)
,
(.15mm)
Spindle Drive Motor 2 hp
(1.5 Kw)
Elevating Motor 1 hp
(.75 Kw)
Coolant Pump Motor 1/8 hp
(.10 Kw)
Dimensions and Weights:
Max. Machine Height (F) 91.3"
(2170mm)
Base and Column Height (G) 79.1"
(2010mm)
Shipping Dim.
Length 66.1"
(1680mm)
Width 32.5"
(826mm)
Height 86.2"
(2190mm)
Net Weight 2,645 lbs.
(1200kg)
Shipping Weight 2,954 lbs.
(1340kg)
Dimensions:
K
L
H
G
E
D C
R x S
Capacities:
Model CL920A
Capacity:
Drilling
In Steel 1.26"
(32mm)
In Cast Iron 2"
(50mm)
Tapping
In Steel 1"
(25mm)
In Cast Iron 1.26"
(32mm)
Boring
In Steel 2.75"
(70mm)
In Cast Iron 4.06"
(105mm)
B
Q
A
F
Clausing Radial Drills
Models: CL920A
Features and Standard Equipment:
●
Limit switch
●
High speed gears are made of Nickel-Chrome Steel
and are heat-treated and ground for durability
Powerful 2 Hp spindle drive motor for heavy-duty
cutting
●
Extra auxiliary dial for spindle feed depth indication,
allows review of spindle feed depth, .0394" to 7.874"
●
Special spindle balance mechanism, superior to
traditional balance mechanism and extends Balance
Spring life
●
Coolant system
●
Low volt and overload protection
●
230/3/60 volt standard
●
Tool kit and manuals
Specifications:
Model CL920A
Working Area:
Column Sleeve Dia. (E) 8.28"
(210mm)
Column Face to Spindle Center
Maximum (D+C) 37.4"
(950mm)
Minimum (D) 8.7"
(220mm)
Spindle Head Travel (C) 28.7"
(730mm)
Base Surface to Spindle End
Maximum (A) 47.6"
(1210mm)
Minimum (B) 13.8"
(350mm)
Arm Vertical Travel (A-B) 33.8" (858mm)
Arm Rotation (Right & Left) 180°
Baseplate Working Surface 35.5" x 25.3"
(902x643mm)
Box Table Area
Length (L) 23.6"
(600mm)
Width (K) 17.5"
(445mm)
Height (H) 15"
(382mm)
Base Dimensions
Floor Area (R x S) 49.6" x
25.2"
(1260x640mm)
Height (Q) 6.5"
(163mm)
Drill Head:
Spindle Taper 4MT
Spindle Stroke 8.66"
(220mm)
Quill Diameter 2.95"
(75mm)
Number of Spindle Speeds 6
Spindle Speeds (rpm) 88, 154, 282, 455, 796, 1500
Number of Feeds 3
Spindle Feed Rate (in
/ rev.) 0.002"/0.0035"/0.006"
( mm
/rev.)
.05mm/.09mm/.15mm)
Spindle Drive Motor 2 hp
(1.5 Kw)
Elevating Motor 1 hp
(.75 Kw)
Coolant Pump Motor 1/8 hp
(.10 Kw)
Dimensions and Weights:
Max. Machine Height (F) 91.3"
(2320mm)
Base and Column Height (G) 79.1"
(2010mm)
Shipping Dim.
Length 71.1"
(1806mm)
Width 32.5"
(826mm)
Height 86.2"
(2190mm)
Net Weight 2,756 lbs.
(1250kg)
Shipping Weight 3,086 lbs.
(1400kg)
Page 31
Dimensions:
H
L
K
G
E
D
C
R x S
Capacities:
Model CL1100
Capacity:
Drilling
In Steel 1.65"
(42mm)
In Cast Iron 2.16"
(55mm)
Tapping
In Steel 1"
(25mm)
In Cast Iron 1.5"
(38mm)
Boring
In Steel 3.35"
(85mm)
In Cast Iron 4.72"
(120mm)
Page 32
B
Q
A
F
Clausing Radial Drills
Model: CL1100
Features and Standard Equipment:
●
High-quality cast-iron arm with heat-treated and ground slides for
smooth and accurate head positioning
●
The bearing bracket for gear-box is fitted with standard bearings to
fit arm slide for smooth gear-box operation
●
High speed gears are made of Nickel-Chrome Steel and are
heat-treated and ground for durability
●
Powerful 3 Hp, 2-speed, heavy-duty spindle drive motor
Overload protection device
●
The main spindle is balanced by a specially shaped spring
Coolant system
●
Low volt and overload protection
●
Tool kit and manuals
●
230/3/60 volt standard or other voltages require optional
transformer or special order
Specifications:
Model CL1100
Working Area:
Column Sleeve Dia. (E) 10.24"
(260mm)
Column Face to spindle Center
Maximum (D+C) 43.3"
(1100mm)
Minimum (D) 11.0"
(280mm)
Spindle Head Travel (C) 32.3"
(820mm)
Base Surface to Spindle End
Maximum (A) 50.0"
(1270mm)
Minimum (B) 18.5"
(470mm)
Arm Vertical Travel (A-B) 31.5" (800mm)
Arm Rotation (Right & Left) 180°
Baseplate Working Surface 48" x 29.1"
(1219 x 739mm)
Box Table Area
Length (L) 25.1" (640mm)
Width (K) 20.4" (520mm)
Height (H) 16.5" (420mm)
Base Dimensions
Floor Area (R x S) 67.9" x 28.1"
(1725 x 715mm)
Height (Q) 7.1"
(180mm)
Drill Head:
Spindle Taper 4MT
Spindle Stroke 9.05"
(230mm)
Quill Diameter 3.15"
(80mm)
Number of Spindle Speeds 12
Spindle Speeds (rpm) 44-1500
Number of Feeds 3
Spindle Feed Rate (in
(mm)
/rev.) 0.002"
(.05mm)
, 0.0035"
(.09mm)
, 0.006"
(.15mm)
Spindle Drive Motor (2-speed) 3 hp
(2.25 Kw)
Elevating Motor 1 hp
(.75 Kw)
Coolant Pump Motor 1/8 hp
(.10 Kw)
Dimensions and Weights:
Max. Machine Height (F) 99.6"
(2530mm)
Base and Column Height (G) 78.7"
(2000mm)
Shipping Dim.
Length 74.0"
(1880mm)
Width 34.0"
(864mm)
Height 87"
(2210mm)
Net Weight 3,968 lbs.
(1800kg)
Shipping Weight 4,299 lbs.
(1950kg)
Dimensions:
H
L
K
G
E
D
C
R x S
Capacities:
Model CL1230H
Capacity:
Drilling
In Steel 1.65"
(42mm)
In Cast Iron 2.16"
(55mm)
Tapping
In Steel 1"
(25mm)
In Cast Iron 1.38"
(38mm)
Boring
In Steel 3.38"
(86mm)
In Cast Iron 4.72"
(120mm)
B
Q
A
F
Clausing Radial Drills
Model: CL1230H
Features and Standard Equipment:
●
High-quality cast-iron arm with heat-treated and ground slides for
smooth and accurate head positioning
●
The bearing bracket for gear-box is fitted with standard bearings to
fit arm slide for smooth gear-box operation
●
High speed gears are made of Nickel-Chrome Steel and are
heat-treated and ground for durability
●
Powerful 3 Hp, 2-speed, heavy-duty spindle drive motor
●
Overload protection device
●
The main spindle is balanced by an adjustable block
●
Coolant system
●
Low volt and overload protection
●
Equipped with hydraulic clamping. With a push of a button you can have
arm unclamped then move vertically, or stop then clamp automatically
●
Tool kit and manuals
●
230/3/60 volt standard or other voltages require optional
transformer or special order
Specifications:
Model CL1230H
Working Area:
Column Sleeve Dia. (E) 11.81"
(300mm)
Column Face to Spindle Center
Maximum (D+C) 46.1"
(1170mm)
Minimum (D) 13.4"
(340mm)
Spindle Head Travel (C) 35.0"
(890mm)
Base Surface to Spindle End
Maximum (A) 53.9"
(1370mm)
Minimum (B) 19.3"
(490mm)
Arm Vertical Travel (A-B) 34.6" (880mm)
Arm Rotation (Right & Left) 180°
Baseplate Working Surface 48" x 29.1"
(1219 x 739mm)
Box Table Area
Length (L) 25.1" (640mm)
Width (K) 20.4" (520mm)
Height (H) 16.5" (420mm)
Base Dimensions
Floor Area (R x S) 67.9" x 28.1"
(1725 x 715mm)
Height (Q) 7.1"
(180mm)
Drill Head:
Spindle Taper 4MT
Spindle Stroke 9.84"
(250mm)
Quill Diameter 3.15"
(80mm)
Number of Spindle Speeds 2
Spindle Speeds (rpm) 44-1500
Number of Feeds 3
Spindle Feed Rate (in(mm)/rev.) 0.002"(.05mm), 0.0035"
(.09mm)
, 0.006"
(.15mm)
Spindle Drive Motor (2-speed) 3 hp
(2.25 Kw)
Elevating Motor 1 hp
(.75 Kw)
Clamping Motor 1 hp
(.75 Kw)
Coolant Pump Motor 1/8 hp
(.10 Kw)
Dimensions and Weight:
Max. Machine Height (F) 109.5"
(2780mm)
Base and Column Height (G) 81.1"
(2060mm)
Shipping Dim.
Length 80.1"
(2035mm)
Width 32.5"
(862mm)
Height 88.2"
(2240mm)
Net Weight 4,630 lbs.
(2100kg)
Shipping Weight 5,071 lbs.
(2300kg)
Page 33
Shown with Optional Tilt Table
Dimensions:
H
L
K
G
E D
C
R x S
Capacities:
Model CLC1250H
Capacity:
Drilling
In Steel 1.97"
(50mm)
In Cast Iron 2.36"
(60mm)
Tapping
In Steel 1.57"
(40mm)
In Cast Iron 1.97"
(50mm)
Boring
In Steel 4.33"
(110mm)
In Cast Iron 6.55"
(165mm)
Page 34
A
B
Q
F
Clausing Radial Drills
Model: CLC1250H
Features and Standard Equipment:
●
Equipped with hydraulic separate clamping unit. Vertical
movement of arm is coordinated by an IC timer. With a single
touch on push button switch, you can have the arm unclamped then
move vertically, or stop then clamp automatically. Very easy to
operate, and tools will always stay at the same point after tool shifting
●
Gears in gear box are cooled by oil cycled by an oil pump to
minimize gear wear
●
Powerful 5 Hp, 2-speed, heavy-duty spindle drive motor
●
Friction type disc clutch absorbs impact force caused by vertical movement
of spindle, and protects all transmission units inside gear box. With quick
spindle return, the clutch will help speed-up the tapping operation
●
Special arm elevating device is provided to prevent arm from falling
down abruptly after years of usage
●
Coolant system
●
Tool kit and manuals
●
230/3/60 volt standard or other voltages require optional transformer
or special order
Specifications:
Model CLC1250H
Working Area:
Column Sleeve Dia. (E) 11.81"
(300mm)
Column Face to Spindle Center
Maximum (D+C) 49.21"
(1250mm)
Minimum (D) 14.17"
(360mm)
Spindle Head Travel (C) 35.04"
(890mm)
Base Surface to Spindle End
Maximum (A) 52.95"
(1345mm)
Minimum (B) 17.36"
(441mm)
Arm Vertical Travel (A-B) 28.1" (715mm)
Arm Rotation (Right & Left) 180°
Baseplate Working Surface 48" x 29.1"
(1219 x 739mm)
Box Table Area
Length (L) 25.1" (640mm)
Width (K) 20.4" (520mm)
Height (H) 16.5"
(420mm)
Base Dimensions
Floor Area (R x S) 70.3" x 30.9"
(1785 x 785mm)
Height (Q) 7.8"
(190mm)
Drill Head:
Spindle Taper 5MT
Spindle Stroke 10.63"
(270mm)
Quill Diameter 3.15"
(80mm)
Number of Spindle Speeds 12
Spindle Speeds (rpm) 56-1450
Number of Feeds 3
Spindle Feed Rate (in(mm)/rev.) 0.0023"(.06mm), 0.004"
(.10mm)
, 0.008"
(.20mm)
Spindle Drive Motor (2-speed) 5 hp
(3.8 Kw)
Elevating Motor 1 hp
(.75 Kw)
Clamping Motor 1 hp
(.75 Kw)
Coolant Pump Motor 1/8 hp
(.10 Kw)
Dimensions and Weight:
Max. Machine Height (F) 104.1"
(2645mm)
Base and Column Height (G) 81.9"
(2080mm)
Shipping Dim.
Length 81.1"
(2060mm)
Width 39.2"
(995mm)
Height 88.2"
(2240mm)
Net Weight 5,071 lbs.
(2300kg)
Shipping Weight 5,512 lbs.
(2500kg)
Shown with Optional Tilt Table
Dimensions:
H
L
K
G
E
D
C
R x S
Capacities:
Model CLC1600H
Capacity:
Drilling
In Steel 1.97"
(50mm)
In Cast Iron 2.36"
(60mm)
Tapping
In Steel 1.57"
(40mm)
In Cast Iron 1.97"
(50mm)
Boring
In Steel 4.33"
(110mm)
In Cast Iron 6.55"
(165mm)
A
B
Q
F
Clausing Radial Drills
Model: CLC1600H
Features and Standard Equipment:
●
Equipped with hydraulic separate clamping unit. Vertical
movement of arm is coordinated by an IC timer. With a single
touch on push button switch, you can have the arm unclamped then
move vertically, or stop then clamp automatically. Very easy to
operate, and tools will always stay at the same point after tool shifting
●
Gears in gear box are cooled by oil cycled by an oil pump to
minimize gear wear
●
Powerful 5 Hp, 2-speed, heavy-duty spindle drive motor
●
Friction type disc clutch absorbs impact force caused by vertical movement
of spindle, and protects all transmission units inside gear box. With quick
spindle return, the clutch will help speed-up the tapping operation
●
Special arm elevating device is provided to prevent arm from falling
down abruptly after years of usage
●
Coolant system
●
Tool kit and manuals
●
230/3/60 volt standard or other voltages require optional transformer
or special order
Specifications:
Model CLC1600H
Working Area:
Column Sleeve Dia. (E) 12.61"
(320mm)
Column Face to Spindle Center
Maximum (D+C) 63.00"
(1600mm)
Minimum (D) 13.78"
(350mm)
Spindle Head Travel (C) 49.21"
(1250mm)
Base Surface to Spindle End
Maximum (A) 55.90"
(1420mm)
Minimum (B) 18.31"
(465mm)
Arm Vertical Travel (A-B) 36.7" (932mm)
Arm Rotation (Right & Left) 180°
Baseplate Working Surface 70.9" x 40.4"
(1800 x 1026mm)
Box Table Area
Length (L) 24.8"
(630mm)
Width (K) 19.7"
(500mm)
Height (H) 19.7"
(500mm)
Base Dimensions
Floor Area (R x S) 100.4" x 38.2"
(2550 x 970mm)
Height (Q) 7.9"
(200mm)
Drill Head:
Spindle Taper 5MT
Spindle Stroke 10.63"
(270mm)
Quill Diameter 3.15"
(80mm)
Number of Spindle Speeds 12
Spindle Speeds (rpm) 56-1450
Number of Feeds 3
Spindle Feed Rate (in(mm)/rev.) 0.0023"(.06mm), 0.004"
(.10mm)
, 0.008"
(.20mm)
Spindle Drive Motor (2-speed) 5 hp
(3.8 Kw)
Elevating Motor 1 hp
(.75 Kw)
Clamping Motor 1 hp
(.75 Kw)
Coolant Pump Motor 1/8 hp
(.10 Kw)
Dimensions and Weight:
Max. Machine Height (F) 108.7"
(2760mm)
Base and Column Height (G) 86.1"
(2186mm)
Shipping Dim.
Length 105.2"
(2670mm)
Width 44.1"
(1120mm)
Height 94.9"
(2410mm)
Net Weight 7,275 lbs.
(3300kg)
Shipping Weight 8,378 lbs.
(2800kg)
Page 35
Clausing Radial Drills
Model: CL1600H
Features and Standard Equipment:
●
Equipped with hydraulic separate clamping unit. Vertical
movement of arm is coordinated by an IC timer. With a single
touch on push button switch, you can have the arm unclamped then
move vertically, or stop then clamp automatically. Very easy to
operate, and tools will always stay at the same point after tool shifting.
●
Gears in gear box are cooled by oil cycled by an oil pump to
minimize gear wear.
●
Friction type disc clutch absorbs impact force caused by vertical
movement of spindle, and protects all transmission units inside
gear box. With quick spindle return, the clutch will help speed-up
the tapping operation.
●
Special automatic tool eject device is supplied to allow you to
change tools quickly. (No drifter is required) Special arm elevating
device is provided to prevent arm from falling down abruptly after.
●
Coolant system
●
Tool kit and manuals
●
230/3/60 volt standard
Dimensions:
H
L
K
G
E
D
C
R x S
Capacities:
Model CL1600H
Capacity:
Drilling
In Steel 2.6"
(65mm)
In Cast Iron 2.75"
(70mm)
Tapping
In Steel 1.97"
(50mm)
In Cast Iron 2.36"
(60mm)
Boring
In Steel 5"
(126mm)
In Cast Iron 7.28"
(185mm)
B
A
Q
F
Specifications:
Model CL1600H
Working Area:
Column Sleeve Dia. (E) 17"
(432mm)
Column Face to Spindle Center
Maximum (D+C) 62.2"
(1580mm)
Minimum (D) 17.3"
(440mm)
Spindle Head Travel (C) 44.9"
(1140mm)
Base Surface to Spindle End
Maximum (A) 63"
(1600mm)
Minimum (B) 15"
(380mm)
Arm Vertical Travel (A-B) 48" (1220mm)
Arm Rotation (Right & Left) 180°
Baseplate Working Surface 70.9" x 40.4"
(1800 x 1026mm)
Box Table Area
Length (L) 27.6"
(700mm)
Width (K) 19.7"
(500mm)
Height (H) 15.9" (405mm)
Base Dimensions
Floor Area (R x S) 97.6" x
41.3"
(2480 x 1050mm)
Height (Q) 8.26"
(210mm)
Drill Head:
Spindle Taper 5MT
Spindle Stroke 14.6"
(370mm)
Quill Diameter 3.94"
(100mm)
Number of Spindle Speeds 12
Spindle Speeds (rpm) 40-1920
Number of Steps 6
Spindle Feed Rate (in
(mm)
/rev.) 0.003"
(.07mm)-
0.038"
(.96mm)
Spindle Drive Motor (1-speed) 7.5 hp
(5.6 Kw)
Elevating Motor 2 hp
(1.5 Kw)
Clamping Motor
1 hp
(.75 Kw)
Coolant Pump Motor 1/8 hp
(.10 Kw)
Dimensions and Weight
Max. Machine Height (F) 124.8"
(3170mm)
Base and Column Height (G) 107.7"
(2660mm)
Shipping Dim.
Length 112.2"
(2850mm)
Width 55.1"
(1400mm)
Height 115.7"
(2940mm)
Net Weight 10,805 lbs.
(4900kg)
Shipping Weight 11,245 lbs.
(5100kg)
Page 36
Dimensions:
H
L
K
G
E
D
C
R x S
Capacities:
Model CL2000H
Capacity:
Drilling
In Steel 2.6"
(65mm)
In Cast Iron 2.75"
(70mm)
Tapping
In Steel 1.97"
(50mm)
In Cast Iron 2.36"
(60mm)
Boring
In Steel 5"
(126mm)
In Cast Iron 7.28"
(185mm)
B
A
Q
F
Clausing Radial Drills
Model: CL2000H
Features and Standard Equipment:
●
Equipped with hydraulic separate clamping unit. Vertical
movement of arm is coordinated by an IC timer. With a single
touch on push button switch, you can have the arm unclamped then
move vertically, or stop then clamp automatically. Very easy to
operate, and tools will always stay at the same point after tool shifting.
Gears in gear box are cooled by oil cycled by an oil pump to
minimize gear wear.
●
Friction type disc clutch absorbs impact force caused by vertical
movement of spindle, and protects all transmission units inside
gear box. With quick spindle return, the clutch will help speed-up
the tapping operation.
●
Special arm elevating device is provided to prevent arm from falling
down abruptly after years of usage.
●
Coolant system
●
Tool kit and manuals
●
230/3/60 volt standard
Specifications:
Model CL2000H
Working Area:
Column Sleeve Dia. (E) 17"
(432mm)
Column Face to Spindle Center
Maximum (D+C) 78.7"
(2000mm)
Minimum (D) 19.3"
(490mm)
Spindle Head Travel (C) 59.4"
(1510mm)
Base Surface to Spindle End
Maximum (A) 74.8"
(1900mm)
Minimum (B) 19.7"
(500mm)
Arm Vertical Travel (A-B) 55.1" (1400mm)
Arm Rotation (Right & Left) 180°
Baseplate Working Surface
Box Table Area
Length (L) 39.3"
(1000mm)
Width (K) 31.5"
(800mm)
Height (H) 19.7"
(500mm)
Base Dimensions
Floor Area (R x S) 114.5" x
43.3"
(2908 x 1102mm)
Height (Q) 98.4"
(250mm)
Drill Head:
Spindle Taper 5MT
Spindle Stroke 14.6"
(370mm)
Quill Diameter 3.94"
(100mm)
Number of Spindle Speeds 12
Spindle Speeds (rpm) 35-1890
Number of Steps 6
Spindle Feed Rate (in
(mm)
/rev.) 0.003"
(.07mm)-
0.038"
(.96mm)
Spindle Drive Motor (1-speed) 7.5 hp
(5.6 Kw)
Elevating Motor 3 hp
(2.25 Kw)
Clamping Motor
1 hp
(.75 Kw)
Coolant Pump Motor 1/8 hp
(.10 Kw)
Dimensions and Weight
Max. Machine Height (F) 124.8"
(3470mm)
Base and Column Height (G) 116.5"
(2960mm)
Shipping Dim.
Length 122.2"
(3105mm)
Width 55.1"
(1400mm)
Height 127.5"
(3240mm)
Net Weight 13,448 lbs.
(6100kg)
Shipping Weight 14,550 lbs.
(6600kg)
Page 37
Clausing Radial Drills
Model: CLC2500
Features and Standard Equipment:
●
Equipped with hydraulic separate clamping unit. Vertical
movement of arm is coordinated by an IC timer. With a single
touch on push button switch, you can have the arm unclamped then
move vertically, or stop then clamp automatically. Very easy to
operate, and tools will always stay at the same point after tool shifting
●
Gears in gear box are cooled by oil cycled by an oil pump to
minimize gear wear
●
Friction type disc clutch absorbs impact force caused by vertical
movement of spindle, and protects all transmission units inside
gear box. With quick spindle return, the clutch will help speed-up
the tapping operation
●
Special arm elevating device is provided to prevent arm from falling
down abruptly after years of usage
●
Coolant system
●
Tool kit and manuals
●
230/3/60 volt standard
Dimensions:
H
L
K
G
E
D
C
R x S
Capacities:
Model CLC2500
Capacity:
Drilling
In Steel 3.15"
(80mm)
In Cast Iron 3.98"
(100mm)
Tapping
In Steel 2.56"
(65mm)
In Cast Iron 2.95"
(75mm)
Boring
In Steel 6"
(150mm)
In Cast Iron 10"
(250mm)
B
A
Q
F
Specifications:
Model CLC2500
Working Area:
Column Sleeve Dia. (E) 21.65"
(550mm)
Column Face to Spindle Center
Maximum (D+C) 98.4"
(2500mm)
Minimum (D) 19.7"
(500mm)
Spindle Head Travel (C) 78.7"
(2000mm)
Base Surface to Spindle End
Maximum (A) 78.7"
(2000mm)
Minimum (B) 21.6"
(550mm)
Arm Vertical Travel (A-B) 57.1" (1450mm)
Arm Rotation (Right & Left) 180°
Baseplate Working Surface 86.8" x 43.4"
(2205 x 1102mm)
Box Table Area
Length (L) 39.4"
(1000mm)
Width (K) 31.5"
(800mm)
Height (H) 22"
(560mm)
Base Dimensions
Floor Area (R x S) 138.6" x
55.1"
(3520 x 1400mm)
Height (Q) 12.6"
(320mm)
Drill Head:
Spindle Taper 6MT
Spindle Stroke 17.7"
(450mm)
Quill Diameter 3.94"
(100mm)
Number of Spindle Speeds 16
Spindle Speeds (rpm) 16-1250
Number of Steps 16
Spindle Feed Rate (in
(mm)
/rev.) 0.0015"
(.04mm)-
0.126"
(3.20mm)
Spindle Drive Motor (1-speed) 10 hp
(7.5 Kw)
Elevating Motor 5 hp
(3.6 Kw)
Coolant Pump Motor 1/4 hp
(.18 Kw)
Dimensions and Weight:
Max. Machine Height (F) 157"
(3990mm)
Base and Column Height (G) 151.6"
(2660mm)
Shipping Dim.
Length 158"
(4000mm)
Width 63"
(1600mm)
Height 151.6"
(3850mm)
Net Weight 24,250 lbs.
(11000kg)
Shipping Weight 27,557 lbs.
(12500kg)
Page 38
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project