Bürkert 2730, 2731, K diaphragm control valve Operating Instructions

Type 2730, 2731, 2731 K
DN 15 - 50
Piston controlled diaphragm control valve
Kolbengesteuertes Membranregelventil
Vanne de réglage à membrane commandée par piston
Operating Instructions
Bedienungsanleitung
Manuel d‘utilisation
We reserve the right to make technical changes without notice.
Technische Änderungen vorbehalten.
Sous réserve de modifications techniques.
© Bürkert Werke GmbH & Co. KG, 200 - 2017
Operating Instructions 1706/_EU-EN_008 / Original DE
Type 2730, 2731 and 2731 K

1
Operating instructions.................................................................4
1.1 Definition of term “device”........................................................ 4
1.2 Symbols........................................................................................ 4
2
Authorized use.......................................................................................5
3
Basic safety instructions...........................................................5
4
General information.........................................................................6
4.1 Contact address......................................................................... 6
4.2 Warranty....................................................................................... 6
4.3 Information on the internet....................................................... 6
5
Product description.........................................................................7
5.1 General description................................................................... 7
5.2 Properties..................................................................................... 7
5.3 Structure and function.............................................................. 7
6
Technical data.........................................................................................8
6.1 Conformity.................................................................................... 8
6.2 Standards..................................................................................... 8
6.3 Type label..................................................................................... 8
6.4 Labeling of the forged bodies................................................. 9
6.5 Labeling of the tube valve body (VP)..................................... 9
6.6 Operating conditions...............................................................10
6.7 Flow values and characteristics............................................16
6.8 General technical data............................................................16
7
Installation............................................................................................. 17
7.1 Before installation.....................................................................17
7.2
7.3
Installation..................................................................................19
Pneumatic connection.............................................................20
8
Removal....................................................................................................... 21
9
Electrical control unit............................................................. 21
10 Malfunctions......................................................................................... 22
11 Maintenance............................................................................................ 22
11.1 Maintenance and cleaning.....................................................22
11.2 Replacing the diaphragm.......................................................24
12 Replacement parts........................................................................... 26
12.1 Order table.................................................................................27
13 Packaging, transport, storage........................................... 28
english
3
Type 2730, 2731 and 2731 K
Operating instructions
1
Operating instructions
The operating instructions describe the entire life cycle of the device.
Keep these instructions in a location which is easily accessible to
every user and make these instructions available to every new owner
of the device.
1.2
Danger!
Warns of an immediate danger.
▶▶ Failure to observe the warning may result in a fatal or serious injury.
Warning!
Important safety information.
Failure to observe these instructions may result in hazardous
situations.
▶▶ The operating instructions must be read and understood.
Symbols
Warns of a potentially dangerous situation.
▶▶ Failure to observe the warning may result in serious injuries or
death.
Caution!
1.1
Definition of term “device”
The term “device” used in these instructions always stands for the
diaphragm control valve Type 2730, 2731 and 2731 K.
Warns of a possible danger.
▶▶ Failure to observe this warning may result in a moderately severe
or minor injury.
Note!
Warns of damage to property.
Important additional information, tips and recommendations.
Refers to information in these operating instructions or in
other documentation.
▶▶ designates instructions for risk prevention.
→→designates a procedure which you must carry out.
4
english
Type 2730, 2731 and 2731 K
Authorized use
2
Authorized use
Non-authorized use of the diaphragm control valve Type 2730,
2731 and 2731 K may be a hazard to people, nearby equipment
and the environment.
▶▶ The device is designed for the controlled flow of liquid media.
▶▶ In the potentially explosion-risk area Type 2730, 2731 and 2731 K
may be used only according to the specification on the separate
Ex type label. For use observe the additional information enclosed
with the device together with safety instructions for the explosionrisk area.
▶▶ Devices without a separate Ex type label may not be used in a
potentially explosive area.
▶▶ The admissible data, the operating conditions and conditions of
use specified in the contract documents, operating instructions
and on the label are to be observed during use. The designated
application cases are specified in the chapter entitled “5 Product
description”.
▶▶ The device may be used only in conjunction with third-party devices
and components recommended and authorised by Bürkert.
▶▶ Correct transportation, correct storage and installation and careful use and maintenance are essential for reliable and faultless
operation.
▶▶ Use the device only as intended.
3
Basic safety
instructions
These safety instructions do not make allowance for any
• contingencies and events which may arise during the installation,
operation and maintenance of the devices.
• local safety regulations, whereby the operator is responsible for their
compliance, by the installation personnel too.
Danger!
Danger – high pressure.
▶▶ Before dismounting the lines and valves, turn off the pressure and
vent the lines.
Risk of electric shock.
▶▶ Before reaching into the device, switch off the power supply and
secure to prevent reactivation.
▶▶ Observe applicable accident prevention and safety regulations
for electrical equipment.
Risk of injury when opening the actuator.
The actuator contains a tensioned spring. If the actuator is opened,
there is a risk of injury from the spring jumping out!
▶▶ The actuator must not be opened.
Risk of burns.
The surface of the device may become hot during long-term operation.
▶▶ Do not touch the device with bare hands.
english
5
Type 2730, 2731 and 2731 K
General information
General hazardous situations.
To prevent injury, ensure that:
▶▶ The system cannot be activated unintentionally.
▶▶ Installation and repair work may be carried out by authorized
technicians only and with the appropriate tools.
▶▶ After an interruption in the power supply or pneumatic supply,
ensure that the process is restarted in a defined or controlled
manner.
▶▶ The device may be operated only when in perfect condition and
in consideration of the operating instructions.
▶▶ The general rules of technology apply to application planning and
operation of the device.
To prevent damage to property on the device, ensure:
▶▶ Supply the media connections only with those media which are
specified as flow media in the chapter entitled “6 Technical data”.
▶▶ Do not put any loads on the valve (e.g. by placing objects on it
or standing on it).
▶▶ Do not make any external modifications to the valves. Do not paint
the body parts or screws.
4
General information
4.1
Contact address
Germany
Bürkert Fluid Control Systems
Sales Center
Christian-Bürkert-Str. 13-17
D-74653 Ingelfingen
Tel.: + 49 (0)7940 - 10 91 111
Fax: + 49 (0)7940 - 10 91 448
E-mail: [email protected]
International
Contact addresses are found on the final pages of the printed operating manual.
You can also find information on the Internet under:
www.burkert.com
4.2
Warranty
The warranty is only valid if the device is used as authorized in accordance with the specified application conditions.
4.3
Information on the internet
The operating instructions and data sheets for Type 2730, 2731 and
2731 K can be found on the Internet at: www.burkert.com
6
english
Type 2730, 2731 and 2731 K
Product description
5
Product description
5.1
General description
The piston-controlled diaphragm control valve Type 2730, 2731 and
2731K is suitable for liquid media. Using neutral gases or air (control
media), it controls the flow of dirty, aggressive, ultrapure or sterile media,
even highly viscous media can be used (flow media). The operation of
the diaphragm control valve Type 2730, 2731 and 2731K is possible
only in combination with an control unit.
5.2
Properties
5.3
Structure and function
The operation of the diaphragm control valve Type 2730, 2731
and 2731 K is possible only in combination with an control unit.
Possible control units are:
Positioner Type 8635, 8692, 8694, 8792
Process controller Type 8693, 8793
5.3.1
Structure
The piston-controlled diaphragm control valve consists of a pneumatically operated piston actuator and a 2/2-way valve body.
• Any flow direction.
• Self-draining for appropriate installation. The ends of the utilized
connections must be cylindrical.
Actuator cover
• Free of empty space.
Actuator body
• Low-turbulence flow.
• High flow values by the streamlined valve body.
Upper pilot air port
• Maintenance-free under normal conditions.
Lower pilot air port
5.2.1
Diaphragm socket
Actuator sizes
Diaphragm
The piston-controlled diaphragm control valve is available for the following actuator sizes: ø 80 mm, ø 100 mm, ø 125 mm.
Line connection
5.2.2
Valve body
Pilot pressure
Designs with lower pilot pressure (reduced spring force) are available
on request.
Fig. 1:
Structure and description
english
7
Type 2730, 2731 and 2731 K
Technical data
5.3.2
Function
Spring force (CFA) or pneumatic pilot pressure (CFB) generates the
closing force on the diaphragm pressure piece. The force is transferred
via a spindle which is connected to the actuator piston.
Control function A (CFA)
Normally closed by spring action
6
Technical data
6.1
Conformity
In accordance with the EU Declaration of conformity, the diaphragm
control valve Type 2730, 2731 and 2731 K is compliant with the EU
Directives.
Control function B (CFB)
6.2
Standards
Normally open by spring action
The applied standards, which verify conformity with the EU Directives,
can be found on the EU-Type Examination Certificate and / or the EU
Declaration of Conformity.
6.3
Type label
Control function
Orifice (diaphragm size)
Type
Made in Germany
Sealing material
2731 A 25,0 EPDM VA
D29 Pmed 10 bar
Pilot 5,5-7 bar
Body material
Line connection /
Permitted medium pressure
Permitted pilot pressure
00148320
W14UN
Date of manufacture
Identification number
Fig. 2:
8
english
Type label (example)
Type 2730, 2731 and 2731 K
Technical data
6.4
Labeling of the forged bodies
6.5
Batch number
XX F
XXXXXXXX/XXX
1.4435/316L(VS) XXXX
PN16/CWP150 XXXXXX
XXXXXXXXXX
Material
Material
Company logo
Heat
Production number /
serial number
1.4435
316L(VP)
Self-drain angle
XXXXXXXX
Customer-specific text
(optional)
Nominal pressure
Orifice connection and
pipe dimension
Fig. 3:
Labeling of the tube valve body
(VP)
Nominal
PN16 / CWP150
pressure
Labeling of the forged bodies
XXXXXXXXXX
Production number /
serial number
XXXXXXXX / XXX
XXXX / XXXXXX
Fig. 4:
Connection orifice
and pipe dimensions
Self-drain angle /
Customer-specific text
(optional)
Labeling of the tube valve body (VP)
english
9
Type 2730, 2731 and 2731 K
Technical data
6.6
Operating conditions
Warning!
Risk of injury, chemical burns, scalding due to the device
rupturing at excessively high pressure.
▶▶ Do not exceed the maximum pilot and medium pressure.
▶▶ Observe permitted ambient and medium temperature.
▶▶ Observe specifications on the type label.
6.6.1
Temperature ranges
Permitted ambient temperature actuators
Actuator size
ø 80 mm
Actuator material
ø 100 mm
PA, PPS
Ambient temperature1)
-10 – +60 °C
ø 125 mm
Tab. 1: Permitted ambient temperature actuators
1)
If using a pilot valve / control unit, observe its temperature
range.
Permitted medium temperature for body
lastic body: note that the permissible medium pressure is
P
dependent on the medium temperature (see “Fig. 5: Graph
of medium pressure / medium temperature”).
10
english
Body material
Medium
PVDF (PD)
-10 – +120 °C
PP (PP)
-10 – +80 °C
PVC (PV)
-10 – +60 °C
Tube valve body (VP)
1.4404 (AISI 316L)
Cast body (VG)
1.4435 (AISI 316L)
Forged body (VS)
1.4435 BN2 (AISI 316L)
according to ASME BPE
1997
-10 – +150 °C
Tab. 2: Permitted medium temperature for body
Permitted medium temperature for diaphragms
he indicated medium temperatures apply only to media
T
which do not corrode or swell the diaphragm materials.
The behavior of the medium with respect to the diaphragm
may be changed by the medium temperature.
The function properties, in particular the service life of the diaphragm, may deteriorate if the medium temperature increases.
Do not use the diaphragms as steam shut-off element.
Material
Temperature
Remarks
EPDM (AB)
-10...+130 °C
Steam sterilisation up to +140 °C / 60 min
EPDM (AD) -5...+143 °C
Steam sterilisation up to +150 °C / 60 min
FKM (FF)
0...+130 °C
No steam / dry heat up to +150 °C / 60 min
PTFE (EA)
-10...+130 °C
Steam sterilisation up to +140 °C / 60 min
Type 2730, 2731 and 2731 K
Technical data
Material
Temperature
Remarks
Advanced
PTFE (EU)
-5...+143 °C
Steam sterilisation up to +150 °C / 60 min
Advanced
PTFE (ET)
-10...+90 °C
-
Gylon (ER)
-5...+130 °C
Steam sterilisation up to +140 °C / 60 min
Tab. 3: Permitted medium temperature for diaphragms
6.6.2
Maximum pilot pressure for valves without pneumatic position
controller - only control function B and tube valve body (VP)
Actuator size [mm] Actuator material
Max. permitted pilot
pressure2)
ø 80, ø 100, ø 125
6 bar
Pressure ranges
bserve the maximum pressure range according to the type
O
label!
2)
Pilot pressure for valves with pneumatic position controller
Actuator size [mm]
Pilot pressure
ø 80, ø 100, ø 125
5.5 – 7.0 bar
Tab. 4: Pilot pressure for valves with pneumatic position controller
Maximum pilot pressure for valves without pneumatic position
controller
Max. permitted pilot
pressure2)
ø 80, ø 100
PA
10 bar
ø 125
PA
7 bar
ø 80, ø 100, ø 125
PPS
7 bar
Tab. 5: Pilot pressure for valves without pneumatic position controller
lastic body: note that the permissible medium pressure is
P
dependent on the medium temperature (see “Fig. 5”).
10
Fig. 5:
8
PV
DF
6
4
C
PV
Actuator size [mm] Actuator material
Medium pressure for plastic body
Medium pressure [bar]
To ensure reliable operation with pneumatic position controller,
observe the permitted minimum and maximum pilot pressure!
PA, PPS
Tab. 6: Maximum pilot pressure for valves without pneumatic
position controller - only CFB and tube valve body (VP)
2
0
20
40
PP
60
80
Medium temperature [°C]
100
120
140
Graph of medium pressure / medium temperature
english
11
Type 2730, 2731 and 2731 K
Technical data
Operating pressure for control function A3)
The values apply to
The values apply to
• Plastic body PVDF (PD), PP (PP), PVC (PV)
• Tube valve body (VP) withDIN weld end connection
DIN clamp connection
• Forged steel body (VS)
• Precision casting body (VG)
Max. sealed medium pressure [bar]
Pressure on one
Pressure on both
side
sides
EPDM/FKM
PTFE
EPDM/FKM
15
10
10
10
ø 80
20
10
10
10
25
10
7.5
8.5
ø 100
32
10
8
9
40
10
10
10
ø 125
50
8
7
7
Tab. 7: Operating pressure for control function A
PTFE
10
10
5.5
6
9
6
Actuator size
[mm]
Orifice DN (Diaphragm size)
[mm]
Actuator size
[mm]
• Tube valve body (VP) withISO weld end connection
ISO clamp connection
Threaded connection
Welded neck flange
english
Max. sealed medium pressure [bar]
Pressure on one
Pressure on both
side
sides
EPDM/FKM
PTFE
EPDM/FKM
15
10
10
10
20
10
10
10
ø 80
25
10
10
10
32
10
8
7.5
ø 100
40
10
8
8
ø 125
50
10
10
10
Tab. 8: Operating pressure for control function A
3)
12
Orifice DN (Diaphragm size)
[mm]
Operating pressure for control function A3)
he control functions are described in the chapter entitled “5.3.2
T
Function”.
PTFE
10
10
9
6
6
8.5
Type 2730, 2731 and 2731 K
Technical data
Operating pressure for control function A3)
Required minimum pilot pressure depending on medium pressure
for control function B.
PTFE
EPDM/FKM
20
10
10
10
25
10
10
10
ø 100
40
10
8
8
ø 125
50
10
10
10
Tab. 9: Operating pressure for control function A
ø 80
PTFE
10
9
6
8.5
• Forged steel body (VS)
• Precision casting body (VG)
• Tube valve body (VP) withISO- weld end connection
ISO clamp connection
Threaded connection
Welded neck flange
To protect the diaphragm during control function B, preferably
do not select the pilot pressure higher than is required to
switch the medium pressure.
Control function B / elastomer diaphragm
ø 80 EPDM Fig. 6:
10
9
8
7
6
5
4
3
2
1
0
0
1
DN20
EPDM/FKM
• Plastic body PVDF (PD), PP (PP), PVC (PV)
DN15
Max. sealed medium pressure [bar]
Pressure on one
Pressure on both
side
sides
The values in the following graphs apply to:
DN25
Orifice DN (Diaphragm size)
[mm]
Actuator size
[mm]
• Tube valve body (VP) withOD weld end connection
BS clamp connection
Medium pressure [bar]
The values apply to
2
3
4
5
Pilot pressure [bar]
6
7
8
P
ressure graph, actuator ø 80 mm, control function B,
elastomer diaphragm
english
13
Type 2730, 2731 and 2731 K
DN50
• Tube valve body (VP) with DIN weld end connection
DIN clamp connection
To protect the diaphragm during control function B, preferably
do not select the pilot pressure higher than is required to
switch the medium pressure.
2
3
4
5
Pilot pressure [bar]
6
7
8
P
ressure graph, actuator ø 100 mm and ø 125 mm,
control function B, elastomer diaphragm
Control function B / elastomer diaphragm
ø 80 EPDM DN40
DN32
DN15
DN20
DN25
Control function B / PTFE diaphragm
Medium pressure [bar]
ø 80, ø 100, ø 125 PTFE Fig. 8:
14
10
9
8
7
6
5
4
3
2
1
0
DN50
Fig. 9:
0
1
2
3
4
5
Pilot pressure [bar]
6
7
P
ressure graph, actuator ø 80 mm, ø 100 mm and
ø 125 mm, control function B, PTFE diaphragm
english
8
10
9
8
7
6
5
4
3
2
1
0
0
1
DN25
1
DN15
DN20
0
DN32
Fig. 7:
10
9
8
7
6
5
4
3
2
1
0
The values in the following graphs apply to:
Medium pressure [bar]
Medium pressure [bar]
ø 100, ø 125 EPDM DN32
DN40
Technical data
2
3
4
5
Pilot pressure [bar]
6
7
8
Pressure graph, actuator ø 80 mm, control function B,
elastomer diaphragm
Type 2730, 2731 and 2731 K
• Tube valve body (VP) with OD weld end connection
BS clamp connection
To protect the diaphragm during control function B, preferably
do not select the pilot pressure higher than is required to
switch the medium pressure.
0
1
2
3
4
5
Pilot pressure [bar]
6
7
8
Fig. 10: P
ressure graph, actuator ø 100 mm and ø 125 mm,
control function B, elastomer diaphragm
Medium pressure [bar]
ø 80, ø 100, ø 125 PTFE 10
9
8
7
6
5
4
3
2
1
0
DN50
DN40
DN15
DN20
DN25
DN32
Control function B / PTFE diaphragm
Control function B / elastomer diaphragm
DN20
DN25
10
9
8
7
6
5
4
3
2
1
0
The values in the following graphs apply to:
ø 80 EPDM Medium pressure [bar]
Medium pressure [bar]
ø 100, ø 125 EPDM DN40
DN50
Technical data
10
9
8
7
6
5
4
3
2
1
0
0
1
2
3
4
5
Pilot pressure [bar]
6
7
8
Fig. 12: Pressure graph, actuator ø 80 mm, control function B,
elastomer diaphragm
0
1
2
3
4
5
Pilot pressure [bar]
6
7
8
Fig. 11: P
ressure graph, actuator ø 80 mm, ø 100 mm and
ø 125 mm, control function B, PTFE diaphragm
english
15
Type 2730, 2731 and 2731 K
Medium pressure [bar]
ø 100, ø 125 EPDM 10
9
8
7
6
5
4
3
2
1
0
6.7
DN40
DN50
Technical data
Flow values and characteristics for Types 2730, 2731 and
2731 K you find at www.burkert.com → Type 2730.
6.8
Connections
0
1
2
3
4
5
Pilot pressure [bar]
6
7
8
Line connection
Type 2730
Socket and spigot
Materials
DN50
DN40
DN20
DN25
Medium pressure [bar]
ø 80, ø 100, ø 125 PTFE Pilot air portG1/4, stainless steel
Type 2731 / 2731KWeld end: in accordance with EN ISO
1127 (ISO 4200), DIN 11850 R2
other connections on request
Control function B / PTFE diaphragm
Body
Type 2730PVDF (PD), PP (PP), PVC (PV)
Type 2731 Stainless steel precision casting (VG)
1.4435 (AISI 316L),
Stainless steel forged steel (VS)
1.4435 (AISI 316L)
0
1
2
3
4
5
Pilot pressure [bar]
6
7
Fig. 14: P
ressure graph, actuator ø 80 mm, ø 100 mm and
ø 125 mm, control function B, PTFE diaphragm
16
General technical data
Actuator sizesø 80 mm, ø 100 mm, ø 125 mm
Fig. 13: P
ressure graph, actuator ø 100 mm and ø 125 mm,
control function B, elastomer diaphragm
10
9
8
7
6
5
4
3
2
1
0
Flow values and characteristics
english
8
Type 2731KTube valve body (VP) cold-formed
1.4404 (316L)
Actuator
PA, PPS
Sealing elements actuator FKM, NBR
Type 2730, 2731 and 2731 K
Installation
DiaphragmEPDM in food quality,
PTFE/EPDM,
FKM
Media
Control mediumNeutral gases, air
Quality classes in accordance with
DIN ISO 8573-1
Dust content
7
Installation
Danger!
Danger – high pressure in the equipment.
▶▶ Before loosening the lines and valves, turn off the pressure and
vent the lines.
Class 5:max. particle size 40 μm, max. particle
density 10 mg/m³
Warning!
Water content Class 3:max. pressure dew point - 20 °C or
min. 10 °C below the lowest operating
temperature
Risk of injury from improper installation.
▶▶ Installation may be carried out by authorised technicians only
and with the appropriate tools!
Oil content
Risk of injury from unintentional activation of the system and
an uncontrolled restart.
▶▶ Secure system from unintentional activation.
▶▶ Following assembly, ensure a controlled restart.
Class 5:max. 25 mg/m³ with TopControl
maxi 1 mg/m³ with SideControl
Flow media
Type 2730Liquids; aggressive or abrasive media
Type 2731 / 2731KLiquids; ultrapure, sterile, aggressive
or abrasive media
7.1
Viscosity
• Before connecting the valve, ensure the pipelines are flush.
up to viscous
Before installation
• The flow direction is optional.
Installation positionany position, preferably with the
actuator face up
Protection classIP67 in accordance with
IEC 529 / EN 60529
7.1.1
Installation position general
Installation for self-drainage of the body
It is the responsibility of the installer and operator to ensure
self-drainage.
english
17
Type 2730, 2731 and 2731 K
Installation
Installation for leakage detection
7.1.3
7.1.2
Preparatory work
→→Clean pipelines (sealing material, swarf, etc.).
→→Support and align pipelines.
One of the bores (in the actuator base) for monitoring
leakage must be at the lowest point.
Devices with VG/VS/VA welded body:
Installation position 2/2-way valve
The piston-controlled diaphragm control valve can be installed in any
installation position, preferably with the actuator face up.
To ensure self-drainage:
→→Install body inclined by an angle α = 15° – 35° to the horizontal.
→→Observe an inclination angle of 1° – 5° to the line axis.
Forged and cast body: Mark on the body must point upwards
(12 o’clock position, see “Fig. 15”).
→→One of the bores (in the actuator base) for monitoring leakage
must be at the lowest point.
Mark
Note!
Damage to the diaphragm or the actuator!
▶▶ Before welding in the body, remove the actuator.
Remove the actuator from the valve body:
Note!
Damage to the diaphragm or the seat contour!
▶▶ When removing the actuator, ensure that the valve is in open
position.
→→Control function A pressurize the lower pilot air port with compressed air (5 bar): valve opens.
α
→→Remove actuator with diaphragm by loosening the body screws.
Actuator
Angle α: 15 °– 35°
Inclination to the line axis 1° – 5°
Upper pilot air port
Fig. 15: Installation position for self-drainage of the body
Lower pilot air port
Diaphragm
Body screws (4x)
Valve body
Fig. 16: Installation
18
english
Type 2730, 2731 and 2731 K
Installation
7.2
Installation
Warning!
Risk of injury from improper installation.
Non-observance of the tightening torque is dangerous as the
device may be damaged.
▶▶ Observe the tightening torque (see “Tab. 10: Tightening torques
for diaphragms”).
7.2.1
Installation of the valve body
Welded bodies
→→Weld valve body in pipeline system.
→→Without pressurization tighten the body screws to the permitted
tightening torque (see following table “Tab. 10: Tightening torques
for diaphragms”).
Installation for actuator with control functions B:
→→Lightly cross-tighten the body screws without pressurization until
the diaphragm is between the body and actuator.
Do not tighten the screws yet.
→→Pressurize upper pilot air port of the actuator with compressed
air (5 bar).
→→Actuate the diaphragm control valve twice.
→→With pressurization tighten the body screws to the permitted tightening torque (see “Tab. 10: Tightening torques for diaphragms”).
Other body versions
→→Connect body to pipeline.
7.2.2
Installation of the actuator (welded
body)
Installation for actuator with control function A:
Notice!
Damage to the diaphragm or the seat contour!
▶▶ When installing the actuator, ensure that the valve is in open
position.
→→Control function A pressurize the lower pilot air port with com-
Orifice DN (diaphragm size)
Tightening torques for diaphragms [Nm]
EPDM
PTFE
15
3.5
4
20
4
4.5
25
5
6
32
6
8
40
8
10
50
12
15
Tab. 10: Tightening torques for diaphragms
pressed air (5 bar): valve opens.
→→Lightly cross-tighten the body screws until the diaphragm is
between the body and actuator. Do not tighten the screws yet.
→→Actuate the diaphragm control valve twice.
english
19
Type 2730, 2731 and 2731 K
Installation
7.3
Pneumatic connection
DANGER!
7.3.1
Connection of the actuator
Control functions A:
Danger – high pressure in the equipment.
▶▶ Before loosening the lines and valves, turn off the pressure and
vent the lines.
→→Connect the control medium to the lower pilot air port of the
actuator (see “Fig. 17: Pneumatic connection”)
Control functions B:
→→Connect the control medium to the upper pilot air port of the
Warning!
actuator (see “Fig. 17: Pneumatic connection”)
Risk of injury from unsuitable connection hoses.
Hoses which cannot withstand the pressure and temperature
range may result in hazardous situations.
▶▶ Use only hoses which are authorised for the indicated pressure
and temperature range.
▶▶ Observe the data sheet specifications from the hose manufacturers.
Silencer
For reducing the exhaust air noise: plug the silencer into the free air
discharge connection (see “Fig. 17: Pneumatic connection”)
If used in an aggressive environment, we recommend
conveying all free pneumatic connections into a neutral
atmosphere with the aid of a pneumatic hose.
The operation of the diaphragm control valve Type 2730, 2731
and 2731 K is possible only in combination with an control unit.
Upper pilot air port
Possible control units are:
Positioner Type 8635, 8692, 8694, 8792
Process controller Type 8693, 8793
20
Lower pilot air port
Observe the type label.
Fig. 17: Pneumatic connection
The pneumatic connection of the control unit is described in
the respective operating instructions for the control unit.
Control air hose:
english
Control air hoses of sizes 6/4 mm or 1/4“ can be used.
Type 2730, 2731 and 2731 K
Removal
8
Removal
DANGER!
9
Electrical control unit
The valve Type 2730, 2731 and 2731K can be combined with following control units:
Risk of injury from discharge of medium and pressure.
• Type 8635
It is dangerous to remove a device which is under pressure due to
the sudden release of pressure or discharge of medium.
▶▶ Before removing a device, switch off the pressure and vent the
lines.
• Type 8692Positioner TopControl
→→Loosen the pneumatic connection.
→→Remove the device.
Note!
Positioner SideControl
• Type 8694Positioner TopControl Basic
• Type 8792
Positioner SideControl
• Type 8693
Process controller TopControl
• Type 8793 Process controller SideControl
The electrical connection of the control unit is described in
the respective operating instructions for the control unit.
Deformation of the diaphragm.
▶▶ For prolonged storage of the valves, slacken the housing screws.
english
21
Type 2730, 2731 and 2731 K
Malfunctions
10
11
Malfunctions
DANGER!
Malfunction
Cause /remedial action
Actuator does
not switch
Pilot air port interchanged
4)
CFA:
Connecting lower pilot air port
CFB:
Connecting upper pilot air port
Pilot pressure too low
See pressure specifications on the type label.
Medium pressure too high
See pressure specifications on the type label.
Valve is not
sealed
Medium pressure too high
See pressure specifications on the type label.
Pilot pressure too low
See pressure specifications on the type label.
Flow rate
reduced
PTFE diaphragm bulging
→→Replace diaphragm.
Tab. 11: Malfunctions
Maintenance
Danger – high pressure in the equipment.
▶▶ Before loosening the lines and valves, turn off the pressure and
vent the lines.
Risk of injury due to electrical shock.
▶▶ Before reaching into the system, switch off the power supply
and secure to prevent reactivation!
▶▶ Observe applicable accident prevention and safety regulations
for electrical equipment!
Warning!
Risk of injury from improper maintenance.
▶▶ Installation may be carried out by authorized technicians only
and with the appropriate tools!
Risk of injury from unintentional activation of the system and
an uncontrolled restart.
▶▶ Secure system from unintentional activation.
▶▶ Following maintenance, ensure a controlled restart.
11.1 Maintenance and cleaning
11.1.1 Actuator
4)
see “Fig. 17: Pneumatic connection”
22
english
The actuator of the diaphragm control valve is maintenance-free
provided it is used according to these operating instructions.
Type 2730, 2731 and 2731 K
Maintenance
11.1.2 Wearing parts of the diaphragm
control valve
11.1.4 Service life of the diaphragm
Parts which are subject to natural wear:
• Diaphragm material
• Seals
• Medium, medium pressure, medium temperature
• Diaphragm
• Actuator size
→→If leaks occur, replace the particular wearing part with an appropriate spare part (see chapter “12 Replacement parts”).
A bulging PTFE diaphragm may reduce the flow.
The replacing of the wearing parts is described in chapter
“11.2”.
The service life of the diaphragm depends on the following factors:
• Pilot pressure for CFB.
Protecting the diaphragm
→→For CFA match the actuator size (actuator force) to the medium
pressure to be actuated. If required, select the actuator with
reduced spring force EC04.
→→For CFB try and select the pilot pressure not higher than is
required to actuate the medium pressure.
11.1.3 Inspection intervals
11.1.5 Cleaning
The following maintenance work is required for the diaphragm valve:
Commercially available cleaning agents can be used to clean the
outside.
→→After the first steam sterilization or when required
retighten body screws crosswise.
→→After maximum 105 switching cycles check the diaphragm for
wear.
Muddy and abrasive media require correspondingly shorter
inspection intervals!
Note!
Avoid causing damage with cleaning agents.
▶▶ Before cleaning, check that the cleaning agents are compatible
with the body materials and seals.
english
23
Type 2730, 2731 and 2731 K
Maintenance
11.2 Replacing the diaphragm
DANGER!
It is dangerous to remove a device which is under pressure due to
the sudden release of pressure or discharge of medium.
▶▶ Before removing a device, switch off the pressure and vent the
lines.
20
25
40
50
Notice!
Damage to the diaphragm or the seat contour!
▶▶ When removing the actuator, ensure that the valve is in open
position.
→→Pressurize lower pilot air port of the actuator with compressed
air (5 bar): valve opens.
Fastening types
15
→→Clamp the valve body in a holding device
(applies only to valves not yet installed).
Risk of injury from discharge of medium and pressure.
Orifice
(Diaphragm size)
[mm]
Replacement for control function A
Fastening types for diaphragms
PTFE
EPDM / FKM
Diaphragm with
bayonet catch
Diaphragm with
bayonet catch
Diaphragm with
bayonet catch
Diaphragm screwed in
Tab. 12: Fastening types for diaphragms
→→Loosen the four body screws.
→→Remove the actuator from the body.
→→Unbutton or unscrew old diaphragm. If attachment is with a
bayonet catch, remove the diaphragm by rotating it through 90°.
For orifice DN25-DN50 observe chapter “11.2.1”.
→→Install new diaphragm.
→→Align diaphragm.
The marker flap of the diaphragm must be perpendicular to
the direction of flow (see “Fig. 18”)!
→→Place actuator back on the body.
→→Insert the body screws and lightly cross-tighten until the diaphragm is between the body and actuator.
Do not tighten the screws yet.
→→Actuate the diaphragm control valve twice.
→→Without pressurization tighten the body screws to the per-
mitted tightening torque (see “Tab. 13: Tightening torques for
diaphragms”).
24
english
Type 2730, 2731 and 2731 K
Maintenance
→→Place actuator back on the body.
→→Lightly cross-tighten the body screws without pressurization until
Marker flap of the
diaphragm
Actuator
Upper pilot air port
Lower pilot air port
Diaphragm
Body screws (4x)
Valve body
Fig. 18: Repairs
Replacement for control functions B
→→Clamp the valve body in a holding device (applies only to valves
not yet installed).
→→Loosen the four body screws.
→→Remove the actuator from the body.
→→Unbutton or unscrew old diaphragm. If attachment is with a
bayonet catch, remove the diaphragm by rotating it through 90°.
For orifice DN25-DN50 observe chapter “11.2.1”.
the diaphragm is between the body and actuator.
Do not tighten screws yet.
→→Pressurize upper pilot air port of the actuator with compressed
air (5 bar) (see “Fig. 18”).
→→Actuate the diaphragm control valve twice.
→→With pressurization tighten the body screws to the per-
mitted tightening torque (see “Tab. 13: Tightening torques for
diaphragms”).
Orifice DN (diaphragm
size)
Tightening torques for diaphragms [Nm]
EPDM
PTFE
15
3.5
4
20
4
4.5
25
5
6
32
6
8
40
8
10
50
12
Tab. 13: Tightening torques for diaphragms
15
→→Install new diaphragm.
→→Align diaphragm.
The marker flap of the diaphragm must be perpendicular to
the direction of flow (see “Fig. 18”).
english
25
Type 2730, 2731 and 2731 K
Replacement parts
11.2.1 Switch between PTFE and EPDM diaphragms
Orifice DN15 and DN20:
12
Replacement parts
Caution!
→→Loosen PTFE diaphragm bayonet and attach new EPDM diaphragm.
Risk of injury and/or damage by the use of incorrect parts.
Orifice DN25 up to DN50:
Incorrect accessories and unsuitable replacement parts may
cause injuries and damage the device and the surrounding area.
▶▶ Use only original accessories and original replacement parts
from Bürkert.
→→Loosen PTFE diaphragm bayonet.
→→Place the insert in the pressure piece.
→→Insert and screw in EPDM diaphragm.
The diaphragm is available as a replacement part for the piston-controlled diaphragm control valve Type 2730, 2731 and 2731K.
If you have any queries, please contact your Bürkert sales
office.
Diaphragm
Fig. 19: Diaphragm replacement part
26
english
Type 2730, 2731 and 2731 K
Replacement parts
12.1 Order table
Orifice
(Diaphragm
size) [mm]
Order numbers for diaphragms
EPDM (AB*)
EPDM (AD*)
FKM (FF*)
15
677 664
E02**
688 422
E03**
677 685
F01**
15 BC**
693 162
E02**
693 163
E03**
693 164
F01**
32
677 678
E02PTFE**
679 544
E02PTFE+
Hole**
–
40
677 679
E02PTFE**
679 545
E02PTFE+
Hole**
677 698
L01**
50
677 680
E02PTFE**
679 546
E02PTFE+
Hole**
677 699
L01**
20
677 665
E02**
688 423
E03**
677 686
F01**
20 BC**
693 165
E02**
693 166
E03**
693 167
F01**
25
677 667
E01**
688 424
E03**
677 687
F01**
* SAP Code
32
677 668
E01**
688 425
E03**
677 688
F01**
** Identification on the diaphragm
40
677 669
E01**
688 426
E03**
677 689
F01**
50
677 670
E01**
688 427
E03**
677 690
F01**
PTFE (EA*)
Advanced PTFE (EU*)
Laminated
advanced PTFE (ET*)
15
677 675
E02PTFE**
679 541
E02PTFE+
Hole**
677 695
L02**
20
677 676
E02PTFE**
679 542
E02PTFE+
Hole**
677 696
L02**
25
677 677
E02PTFE**
679 543
E02PTFE+
Hole**
677 697
L01**
Tab. 14: Order numbers for diaphragms
english
27
Type 2730, 2731 and 2731 K
Packaging, transport, storage
13
Packaging, transport,
storage
Note!
Transport damages.
Inadequately protected equipment may be damaged during transport.
• During transportation protect the device against wet and dirt in
shock-resistant packaging.
• Avoid exceeding or dropping below the permitted storage
temperature.
Incorrect storage may damage the device.
• Store the device in a dry and dust-free location.
• Storage temperature -20 – +65 °C.
Damage to the environment caused by device components
contaminated with media.
• Dispose of the device and packaging in an environmentally
friendly manner.
• Observe applicable regulations on disposal and the environment.
Note:
Observe national waste disposal regulations.
28
english
www.burkert.com
">