Beamex MC2 IS Intrinsically Safe Calibrator User Guide

PDF

Document

INTRINSICALLY SAFE CALIBRATOR
User Guide
Dear user,
We have made every effort to ensure the accuracy of the contents of this
manual. Should any errors be detected, we would greatly appreciate to
receive suggestions to improve the quality of the contents of this manual.
The above not withstanding, we can assume no responsibility for any errors
in this manual or their eventual consequences.
We reserve rights to make modifications to this manual without any further
notice.
For more detailed technical data about the MC2-IS Intrinsically Safe
Calibrator, please contact the manufacturer.
&copy; 2008 - 2016
BEAMEX OY AB
Ristisuonraitti 10
FIN-68600 Pietarsaari
FINLAND
Tel
+358 - 10 - 5505000
Fax
+358 - 10 - 5505404
E-mail:
[email protected]
Internet:
http://www.beamex.com
8813000 / MC2-ISuEng / Version 3.12e
Trademarks and Statements
QCAL&reg; is a registered trademark owned by Beamex Oy Ab.
Other trademarks are property of their respective owners.
MC2-IS contains licensed software which requires that the source
code is available for You. Please contact Beamex to obtain it.
MC2-IS is based in part on the work of the FLTK project
(http://www.fltk.org).
Contents
Contents
Part A, General
Introduction ........................................................................................2
About This Manual ................................................................................... 2
Typographical Conventions ............................................................... 3
Unpacking and Inspection ........................................................................ 3
MC2-IS Hardware ...............................................................................4
Connections ............................................................................................. 5
Pressure Modules .............................................................................. 6
Connectors on the Left Side of MC2-IS ............................................. 7
Terminals ........................................................................................... 7
Support for Table Top Use ....................................................................... 8
Memory .................................................................................................... 8
Display...................................................................................................... 8
Keyboard .................................................................................................. 9
Batteries ................................................................................................. 10
About the Charger and the Charging Procedure ............................. 11
Removing/Replacing the Batteries................................................... 12
Capacity Indication ........................................................................... 13
PC Communication .......................................................................... 14
MC2-IS Firmware ..............................................................................15
General Description................................................................................ 15
Startup Procedure ............................................................................ 15
Basic Mode and Higher Level Functions ......................................... 15
Basic Mode's User Interface .................................................................. 16
The Status Bar ................................................................................. 16
Windows 1 and 2 ............................................................................. 16
The Function Key Bar ...................................................................... 17
Menu ................................................................................................ 17
Configuration Windows .......................................................................... 18
Field Types Available for Editing Data ............................................. 19
MC2-IS User Guide
Contents
MC2-IS Options ................................................................................ 23
Hardware Modules/Options .................................................................... 23
Other Devices .................................................................................. 24
Safety ............................................................................................... 25
Symbols Used ........................................................................................ 25
Ex Information and Approvals ................................................................ 26
Safety Precautions and Warnings .......................................................... 26
General Warnings ............................................................................ 27
Warnings Concerning Electrical Measurement and
Generation ....................................................................................... 27
General Warnings Concerning Pressure Measurement .................. 28
Warnings Concerning High Pressure .............................................. 29
Disposal of Waste Electrical and Electronic Equipment .............. 30
Service ............................................................................................. 31
Firmware Update .................................................................................... 31
The Battery Charger ............................................................................... 31
Resetting MC2-IS ................................................................................... 31
Recalibrating MC2-IS ............................................................................. 32
Cleaning MC2-IS .................................................................................... 32
Part B, Startup and Basic Operation
Starting MC2-IS ................................................................................ 34
Startup Procedure .................................................................................. 34
Basic Mode, Defined .............................................................................. 35
Measuring ........................................................................................ 37
Current Measurement ............................................................................ 39
Frequency Measurement ....................................................................... 40
Pressure Measurement .......................................................................... 41
Connecting and Disconnecting External Pressure Modules ............ 42
Zeroing a Pressure Module.............................................................. 43
Pulse Counting ....................................................................................... 44
Resistance Measurement ...................................................................... 45
Switch State Sensing ............................................................................. 46
Temperature Measurement (RTD) ......................................................... 48
Temperature Measurement (Thermocouple) ......................................... 49
Voltage Measurement ............................................................................ 50
MC2-IS User Guide
Contents
Generating/Simulating .....................................................................51
Changing the Generated/Simulated Value............................................. 52
Spinning and Manual Stepping ........................................................ 52
Current Sink ........................................................................................... 54
Current Generation................................................................................. 55
Frequency Generation ........................................................................... 56
Pulse Generation.................................................................................... 57
Resistance Simulation ............................................................................ 58
RTD Sensor Simulation .......................................................................... 59
Thermocouple Simulation ...................................................................... 61
Voltage Generation ................................................................................ 63
Tools Menu .......................................................................................64
Function Info........................................................................................... 65
Alarms .................................................................................................... 66
Damping ................................................................................................. 67
Leak/Stability Test .................................................................................. 68
Stepping ................................................................................................. 70
Ramping ................................................................................................. 73
Manual Stepping .................................................................................... 75
Display Mode and Special Measurements ............................................. 78
Error % ............................................................................................. 79
Error in Input Units ........................................................................... 80
Error in Output Units ........................................................................ 81
Percentage ....................................................................................... 82
Scaling ............................................................................................. 83
Deviation .......................................................................................... 84
Showing Data on the Additional Info Row .............................................. 85
Resetting and Clearing Additional Info Row / Calculations.............. 88
Part C, Advanced Operation and Configurations
Utilities Menu ...................................................................................90
About MC2-IS ......................................................................................... 90
User Setups for Window 1 &amp; 2 ............................................................... 91
Date/Time ............................................................................................... 92
General Settings..................................................................................... 93
Calibrator Adjustment ............................................................................. 94
MC2-IS User Guide
Contents
Custom Test Point Sets .................................................................. 95
Custom Transfer Functions ............................................................ 97
Custom Pressure Units ................................................................. 100
Related Information ....................................................................... 101
Things to Consider when Measuring Pressure .................................... 102
General .......................................................................................... 102
Pressure Type ................................................................................ 102
Pressure Modules and their Naming Conventions ........................ 103
Square Rooting .............................................................................. 104
Thermocouple Measurement/Simulation, Connections and
Troubleshooting ................................................................................... 105
Internal Reference Junction ........................................................... 105
External Reference Junction .......................................................... 106
Error situations ............................................................................... 109
Resistance and RTD Measurement, Connections ............................... 110
4-wire System ................................................................................ 110
3-wire System ................................................................................ 110
Using a Compensation Loop ......................................................... 111
2-wire System ................................................................................ 111
Current Measurement Parallel to a Test Diode, Connections .............. 112
Parallel Functions in MC2-IS ................................................................ 113
Part D, Calibration
General ........................................................................................... 116
Phases of Instrument Calibration ......................................................... 117
As Found Calibration ..................................................................... 118
Adjustment ..................................................................................... 118
As Left Calibration.......................................................................... 119
Calibrating an Instrument ............................................................. 120
A Calibration Procedure Using MC2-IS................................................ 120
Examples of Instrument Calibration ..................................................... 121
Pressure Transmitters.................................................................... 122
Temperature Indicators and Recorders ......................................... 124
Electrical Limit Switches ................................................................ 126
Temperature Sensors .................................................................... 128
MC2-IS User Guide
Contents
Appendixes
Appendix 1, Technical Data...........................................................132
MC2-IS General Specifications ............................................................ 132
Electrical Measurements ...................................................................... 133
Voltage Measurement .................................................................... 133
Current Measurement .................................................................... 133
Frequency Measurement ............................................................... 134
Pulse Counting ............................................................................... 134
Switch Test ..................................................................................... 134
Electrical Generation, Sensor Measurement and Simulation ............... 135
mV Measurement (T/C-Terminals) ................................................. 135
mV Generation (T/C-Terminals) ..................................................... 135
Voltage Generation ........................................................................ 136
mA Generation (Source/Sink) ........................................................ 136
Resistance Measurement .............................................................. 137
Resistance Simulation .................................................................... 137
Frequency Generation.................................................................... 138
Pulse Generation............................................................................ 138
Temperature Measurement and Simulation ......................................... 139
RTD Measurement and Simulation ................................................ 139
Thermocouple Measurement and Simulation ................................ 141
Pressure Modules ................................................................................. 145
Internal Barometric Pressure Module ............................................. 145
External Pressure Modules (EXT-IS and EXT), High
Accuracy......................................................................................... 146
External Pressure Modules (EXT-s-IS and EXT-s), Standard
Accuracy......................................................................................... 148
Appendix 2, Safety Information ....................................................149
Input Parameters .................................................................................. 149
Output Parameters ............................................................................... 150
Connections Using Temperature / Generate Section Terminals
Only ................................................................................................ 150
Connections Using Measure Section Terminals Only ..................... 150
Other Type of Front Panel Connections ......................................... 150
Ex Approvals ........................................................................................ 151
Special Conditions for Safe Use ........................................................... 151
Appendix 3, Index ..........................................................................153
MC2-IS User Guide
Contents
MC2-IS User Guide
Feedback
Feedback
We want to improve our products and services constantly. Therefore
we’d like to know Your opinion of the product You use. Please spend a
moment of Your valuable time in filling this form. All respondents will
receive a surprise gift in return.
Certain questions can be answered immediately after receiving the
product. Others require some use of the product before You are able
to answer them. The best way to fill the form is to answer the items as
it applies, and send the form to us when all items are answered. There
are however no definite restrictions; fill in the form when you feel like it
(all items need not be answered). Then send it to Beamex using one of
the possibilities listed below.
Mail:
Beamex Oy Ab
Quality Feedback
Ristisuonraitti 10
68600 Pietarsaari
FINLAND
Fax
+358 - 10 - 5505404
Only the next page need to be faxed to us.
Internet: http://www.beamex.com
A similar form is available as a web page
E-mail:
MC2-IS User Guide
[email protected]
Refer to the numbered items on the next
page in Your e-mail message.
Feedback
1. Name of the product you give feedback of:
_____________
2. Serial number and software version number (if applicable)
_____________
_____________
3. Any comments when receiving the product. Did the package contain all required
items and was it as expected?
___________________________________________________________
___________________________________________________________
4. For how long have you been using the product?
_____________
5. How helpful was the manual in using the product?
(Tick a box in the percentage scale below)
0 %
1 0 %
2 0 %
3 0 %
4 0 %
5 0 %
6 0 %
7 0 %
8 0 %
9 0 %
1 0 0 %
5 0 %
6 0 %
7 0 %
8 0 %
9 0 %
1 0 0 %
5 0 %
6 0 %
7 0 %
8 0 %
9 0 %
1 0 0 %
6. How well did the product suit your needs?
0 %
1 0 %
2 0 %
3 0 %
4 0 %
7. How satisfied are you with the product?
0 %
1 0 %
2 0 %
3 0 %
4 0 %
8. Did anything in the product exceed your expectations? In that case, what was it?
___________________________________________________________
___________________________________________________________
9. Did anything in the product disappoint you? In that case, please specify.
___________________________________________________________
___________________________________________________________
10. Any ideas You want to propose to Beamex so that we can improve our products,
operations and/or services.
___________________________________________________________
___________________________________________________________
Please fill in these fields in order to receive your surprise gift.
Title &amp; Name:
Please contact me concerning the
Feedback I have given.
Address:
I want to receive more information on
Beamex products.
_____________________
_____________________
_____________________
_____________________
_____________________
Size (tick one)
XS S M L XL XXL
MC2-IS User Guide
General
Things discussed in Part A:
• An introduction to what MC2-IS
is and what the parts of this User
Guide concentrate on.
• A general description of MC2-IS'
hardware.
• A general description of MC2-IS'
firmware.
• The modularity and options of
MC2-IS.
• Safety precautions and
warnings.
• Briefly about how to service
MC2-IS.
Introduction
Introduction
MC2-IS Intrinsically Safe Multifunction Calibrator is a practical tool
for calibration in hazardous environments. MC2-IS has an easy to
use graphical user interface and is capable of calibrating
temperature, electrical and frequency instruments. By using external
pressure modules, it is also capable of calibrating pressure
instruments.
Being a Beamex calibrator, MC2-IS represents the high, uncompromised quality standards evident in other Beamex calibration
equipment. It is another MC calibrator you can rely on and a
calibrator that completes your range of MC calibrators.
About This Manual
This User Guide is divided in four parts: A, B, C and D.
•
•
•
•
Part A discusses general matters. There is also a chapter
about safety.
Part B describes the basic use of MC2-IS such as measuring
signals and setting up Display Modes and Special
Measurements.
Part C handles configuration level usage and also offers more
information concerning measurements/simulations.
Part D concentrates on the calibration of instruments.
Use the information provided in the headers as a quick guide when
searching for a particular subject:
•
•
•
2
The even page header displays the current main topic (e.g.
&quot;Introduction&quot;).
The odd page header displays the secondary level topic (e.g.
&quot;About this Manual&quot;).
The header of each page also indicates the
active part as shown in the adjacent picture
(with Part B active).
MC2-IS User Guide
Unpacking and Inspection
Typographical Conventions
All examples of user interface texts are printed using Bold text, e.g.
Field: Trigger Level
All front panel texts (fixed texts on MC2-IS's cover) are printed using
Narrow and Bold text, e.g.
Function Key F1
Function and Menu keys are often referred to using both the key
name in Narrow and Bold text and the corresponding text (function)
displayed on the screen in Bold text, e.g.
Function Key F3/Menu
Unpacking and Inspection
At the factory each new MC2-IS passes a careful inspection. It
should be free of scrapes and scratches and in proper operation
order upon receipt. The receiver should, however, inspect the unit
for any damage that may have occurred during transit. If there are
signs of obvious mechanical damage, package contents are
incomplete, or the instrument does not operate according to
specifications, contact the purchasing sales office as soon as
possible. The standard accessories are as follows:
•
•
•
•
•
•
•
•
•
•
Calibration certificate,
a warranty card,
a Declaration of Conformity,
this User Guide,
a separate multi-lingual booklet entitled “MC2-IS Safety
Information”
computer communication cable (USB),
battery pack, RB-48-IS,
battery eliminator/charger for the batteries, BC09-IS,
test leads and clips and
a Cu-Cu adapter for millivolt measurement
For a description of available options, see MC2-IS Options on page
23.
If you have to return the instrument to the factory for any reason, use
the original packing whenever possible. Include a detailed
description of the reason for the return.
MC2-IS User Guide
3
MC2-IS Hardware
MC2-IS Hardware
General features:
•
•
•
•
•
•
Integrated impact protectors
A support for using the calibrator on the table
Weight 1070 ... 1080 g (2.37 ... 2.38 lbs) depending on if the
internal barometric option is installed or not.
Operating temperature: -10 ? +50 &deg;C (14 ? 122 &deg;F).
0 ? +35 &deg;C (32 ? 95 &deg;F) when charging the batteries.
Storage temperature: -20 ? +60 &deg;C (-4 ? 140 &deg;F).
Note: The stickers and the batteries may be affected when
storing longer periods in extreme conditions.
Humidity: 0 ? 80 % R.H. non condensing
More comprehensive specifications are available in Appendix 1.
4
MC2-IS User Guide
Connections
Connections
MC2-IS User Guide
5
MC2-IS Hardware
Pressure Modules
Internal Barometric Pressure Module
An Internal Barometric Pressure Module may be included in MC2-IS.
The Internal Barometric Module measures the barometric pressure
through a connection found on the back side of MC2-IS. Normally
nothing needs to be connected to the barometric pressure module's
connector.
External Pressure Modules
MC2-IS has a connector for External Pressure Modules (EXTs). The
connector is located on the left side of MC2-IS.
If an External Pressure Module is connected or removed, MC2-IS
notices it automatically. More of pressure measurement in part B of
this manual.
Remember to be cautious when working with pressure and pressure
modules. See also chapters Safety on page 25 and Safety
Precautions and Warnings on page 26.
Warning!
Standard EXT modules may be used in safe area only. Use EXT-IS
modules in hazardous area.
6
MC2-IS User Guide
Connections
Connectors on the Left Side of MC2-IS
The left side of MC2-IS (front view) has four connectors as follows:
EXT
External Pressure Modules are discussed in chapter
External Pressure Modules on page 6 and in Part
B of this manual.
OPTION
Reserved for future needs
USB
For computer communication, e.g. when updating
the firmware.
For USB driver information, see chapter PC
Communication on page 14.
Warning!
Use USB Computer Connetor in safe area only.
POWER
Charger connector
Warning!
Use charger in safe area only.
Note
There is no galvanic isolation between the connectors on the
left side as well as the internal barometric pressure module
connector.
Terminals
The lower part of the front panel has terminals for measuring,
generating and simulating signals.
Measuring capabilities of Measure section:
•
•
•
•
•
Voltage,
Current,
Frequency,
Pulse Counting and
Switch state sensing.
Measuring capabilities of Temperature/Generate section:
•
•
•
•
MC2-IS User Guide
Low Voltage measurement using either the Low Voltage
connectors or the internal reference junction,
T/C (thermocouple) measurement using either the internal
reference junction or the Low Voltage connectors,
RTD measurement and
Resistance measurement.
7
MC2-IS Hardware
Generation/simulation capabilities of Temperature/Generate section:
•
•
•
•
•
Low Voltage generation using either the Low Voltage
connectors or the internal reference junction,
T/C simulation using either the internal reference junction
or the Low Voltage connectors,
RTD simulation,
Resistance simulation and
Current Sink, i.e. controlling the current flow sourced by
an external supply.
Support for Table Top Use
The support gives you a good viewing angle when MC2-IS is placed
on a table top.
Memory
MC2-IS maintains data very much like personal computers. Data is
saved on a solid state memory that does not need any power to
maintain its state. Solid state memory is shock proof so the data is
not lost when the calibrator is transported.
Also: all available storage can be used for anything that requires it
(e.g. custom test points, custom transfer functions etc.).
Display
MC2-IS has a backlit LCD display. The resolution of the display is
160 x 160 pixels.
The backlight is turned on or off by briefly pressing the power button.
Pressing the button for a longer time shuts down MC2-IS. More of
backlight settings in part C of this manual.
To tune the contrast of the display:
•
Press F1/Contrast when either viewing the welcome
screen or the General Settings screen.
•
Use the up
contrast.
and down
arrow keys to change the
The changed settings are automatically saved as default settings.
8
MC2-IS User Guide
Keyboard
Keyboard
Function Keys
The Function Keys are located below the display. The meaning of
each Function Key varies depending on the situation. The lower
part of the display indicates what the Function Key stands for at the
moment.
Numeric Keys
A B C
1
D E F
2
4
G H I
P Q R S
7
J K L
3
5
M
T U V
8
W
9
6
N O
X Y Z
0
The Number keys are used when entering numbers in numeric
fields and letters in text fields (as in cellular phones).
Pressing the +/- key toggles the sign of the entered numeric value.
In text fields, this key contains a set of symbols and Greek letters.
The Decimal key adds the decimal point to the numeric value that is
currently edited. In text fields, this key contains additional symbols
such as punctuation marks as well as super and subscript numbers.
Arrow Keys and Enter Key
The arrow keys are used when moving the cursor on the screen.
They also have several special functions in certain situations, e.g.
when tuning the contrast of the display.
The Enter key both starts and finishes the editing of all types of
fields.
On/Off Key
The On/Off key switches MC2-IS on and off. Press the On/Off key
for about half-a-second to switch on/off. This delayed function
prevents accidental on/off switching of MC2-IS.
When pressing the On/Off key briefly, it toggles the display back
light on and off.
MC2-IS User Guide
9
MC2-IS Hardware
Batteries
MC2-IS uses rechargeable batteries. MC2-IS may be used while the
Battery Pack is being charged, but then in safe area only.
If the batteries are fully charged and the charger is connected to
MC2-IS, the charger acts as a Battery eliminator.
The operating time without recharging is somewhere between these
two values:
•
•
Full batteries:
Empty batteries:
About 12 hours in measurement mode without the use of
display backlight.
About 4 hours when sourcing a loop with backlight
continuously on
The upper left corner of MC2-IS' display shows a picture of a
battery. The whiter the picture is, the more acute is the need for
recharging.
Warning!
Open/change the Battery Pack in safe area only.
10
MC2-IS User Guide
Batteries
About the Charger and the Charging Procedure
The charger for rechargeable batteries operates in the following
environments:
- Voltage:
100 240 VAC
- Frequency: 50/60 Hz
The charging time is approx. 5 hours. When charging the batteries,
the battery symbol and a plug symbol alternates on the status bar.
When charging is ready, only the plug symbol is shown.
If MC2-IS is shut off and the charger is connected, a battery status
bar appears. See leftmost picture below.
0 3 .1 2 .2 0 0 7 1 2 :2 2 :2 2
C H A R G IN G R E A D Y
B a tte ry s ta tu s
When charging while MC2-IS displays the charging window, MC2-IS
beeps when the batteries are fully charged. Then the display looks
like rightmost picture above.
Warnings!
USE CHARGER IN SAFE AREA ONLY. If you use MC2-IS' carrying
case, remove the charger from it when moving into hazardous area.
The casing of the charger is not IS-compliant.
USE ONLY THE CHARGER PROVIDED WITH THE CALIBRATOR.
The charger should only be used indoors and when charging, the
environment temperature should be between 0 +35 &deg;C
(32 95 &deg;F).
MC2-IS User Guide
11
MC2-IS Hardware
Removing/Replacing the Batteries
To remove or replace the batteries, perform the following procedure:
1. Turn MC2-IS upside down (the display facing the table top)
and lift the support.
2. Unscrew the two screws holding the cover (see the picture
above).
3. Bend the clip holding the battery pack connector and gently
pull the connector out.
4. To replace the battery pack, click the connector of the new
battery pack on its place (noting the polarity) and put the
battery pack in its slot.
12
MC2-IS User Guide
Batteries
Capacity Indication
If you reset the calibrator or remove/replace the battery pack, &quot;teach&quot;
the capacity of the batteries to the calibrator's charging electronics
by doing as follows:
1. Fully charge the batteries
(approx. 12 hours with no
extra load).
2. Connect the current
generation terminals to
the current measurement
terminals as shown in the
adjacent picture.
3. Configure Window to
measure current with
supply on. See also note
below.
4. Configure Window to
generate (sink) 8 mA.
The user interface should
look as in the adjacent
picture.
5. Do not use the
backlight.
6. Let the calibrator fully discharge its batteries. This is the stage
where the charging electronics &quot;learn&quot; the capacity of the
battery pack.
7. When the calibrator shuts itself automatically, the learning is
done.
8. Recharge the batteries and start using the calibrator
Note.
See part B for more detailed information on connections and
configuring Window 1 and 2.
Hint.
If the calibrator's capacity indication has gotten mixed up, use the
following method to reset the capacity indication:
Fully discharge the batteries as presented above. Then start recharging
and immediately select F3/Menu, Calibrator Adjustment and enter
1590 as the &quot;password&quot;. This resets the capacity indication to 0 %.
Then &quot;teach&quot; the capacity of the batteries using the instructions above
again.
Similarly, the &quot;password&quot; 1599 sets the capacity to 100 %, if needed.
MC2-IS User Guide
13
MC2-IS Hardware
PC Communication
The first time you connect MC2-IS to a computer (using the USB
cable provided), Windows' Found New Hardware Wizard initializes.
In Windows XP: Select option Install from a list or specific
location. In the next window, select Don't search. I will choose the
driver to install. Next browse to the location where you have the
driver available. The rest is automatic.
The driver can be found at Beamex's web site
(http://www.beamex.com). Look for MC2/MC2-IS downloads. The
driver is part of the software update package.
Notes.
The driver has been tested on Windows XP, Windows 2000,
Windows Vista and in Windows 7, 32 and 64 bit versions.
Windows 95, 98, NT4, ME operating systems are not supported.
See also possible additional information delivered with the driver.
This procedure is needed when connecting MC2-IS for the first time
to a particular USB port in a PC. After the driver is installed,
communication initializes automatically, if MC2-IS is connected to
the same USB port in a PC.
14
MC2-IS User Guide
General Description
MC2-IS Firmware
MC2-IS' firmware is saved in FLASH memory. Therefore it is relatively
easy to update the firmware whenever a new version with fresh
capabilities is released. See Firmware Update on page 31 for more
information on updating the firmware in your MC2-IS.
General Description
The following chapters briefly describe each main function.
Startup Procedure
When starting MC2-IS the startup procedure ends up in a welcome
screen. From there it proceeds to Basic Mode and you are ready to
start using the calibrator.
A more comprehensive description of the Startup Procedure is in the
beginning of Part B of this manual.
Basic Mode and Higher Level Functions
In Basic Mode you can measure, generate and simulate signals. There
are two separately configurable windows available.
All main functions of Basic Mode are described in part B of this
manual.
Part C concentrates on higher level functions and additional
information.
MC2-IS User Guide
15
MC2-IS Firmware
Basic Mode's User Interface
The main elements of the Basic Mode can be seen in the following
picture:
S ta tu s B a r
W in d o w
1
M a in m e a s u re m e n t 1
W in d o w
2
M a in m e a s u re m e n t 2

0 5 .1 0 .2 0 0 7
k P a
1 0
0
m A
1 2 :5 7 :2 2
G a u g e
1 5 .8
2 0
EI N X T T
3 0
S u p p ly : O n
1 2 .3 3 0 4
1 6 .4 5 8 3
S e tu p
S e tu p
8 .0 1 3 2
M e n u
F u n c tio n K e y b a r
4 0
A la r m s
A d d itio n a l
In fo R o w :
B a r G ra p h
U n s ta b le
r e a d in g
A d d
In fo
M in
M a x
itio n a l
R o w :
a n d
V a lu e s
Other elements can be found in other windows. They are presented
in the subsequent chapters.
The Status Bar
The Status Bar at the top of the display is divided into two sections.
The first (leftmost) section displays the charge level of the battery
and a plug symbol when the charger/battery eliminator is connected.
The second section displays the date and the third the time.
Windows 1 and 2
MC2-IS has two windows in Basic Mode. Both windows can
independently be configured to display a measurement value. They
can also be assigned to more data on the extra info row as seen in
the previous picture.
Part of the window is reserved for alarm symbols as well as an
unstable reading symbol (i.e. the measured value is not steady at
the moment).
16
MC2-IS User Guide
Basic Mode's User Interface
The Function Key Bar
The Function Key Bar at the bottom of the display is visible all the
time. The meaning of the Function Keys varies depending on the
situation. A grayed Function Key text means that the function is
disabled at the moment.
Menu
The Function Keys often open menus, i.e. lists of available items.
.
2 1 .0 8 .2 0 0 8 1 5 :1 0 :2 2
S u p p ly : O n
m A

2 1 .0 8 .2 0 0 8 1 5 :1 0 :2 2
S u p p ly : O n
m A

5 .4 9 7 5
5 .4 9 7 5
k P a
S e tu p
G a u g e
1 2 .3
S e tu p
E X T
M e n u

A b o u
U s e r
k P a D a te
G e n e
C a lib
A c c e
S C A e a v t u nb p cr y e u t l
t th is C a lib r a
S e tu p s fo r
/ T im e G a u
r a l S e ttin g s
r a to r A d ju s tm
s s o r ie s
to r
&amp;
g e E X T
N S B e o d t ut e t po r s m v t a
S M V e e l&auml; e n l cj u t
1 2 .3
e n t
The pair of screenshots above is an example of an opening menu.
This one opens from Basic Mode when F3 Function Key is pressed.
A menu with a longer list has small arrows at the top/bottom of the
list to point out that the list is longer that what is shown.
Use the arrow keys ( and
) to move between menu options.
The F2 Function Key helps you to scroll longer menu list. It allows
you to quickly jump to the end (Bottom) and beginning (Top)
depending on where in the list you are.
Select an item with the Enter key ( ) or use the F3/Select Function
Key. Selecting a menu option results in one of the following events:
1. The menu closes and a window opens for viewing additional
information or for configuring the selected task. This happens,
e.g. when selecting the About this Calibrator menu option
in the picture above.
2. A tick is added/removed from the selected menu item. It
means that the menu item is selected/deselected for a duty.
This happens, e.g. when selecting which items are to be
shown on the Additional Info row.
3. A sub menu opens allowing you to select one of available
sub menu items.
MC2-IS User Guide
17
MC2-IS Firmware
Configuration Windows
There are several types of configuration windows. The examples
below contain a selection of user editable fields.
D A T E / T IM E
k P a
D a te F o rm a t
d d .m m .y y y y
d a y
1 0
m o n th
8
y e a r
2 0 0 4
m in
4 5
s e c
2 2
0 .0 6
E X T
A la r m s A c tiv e
A le r t w h e n th e m e a s u r e m e n t
&gt; 1 .5 0 0
T im e F o r m a t
h h .m m .s s 2 4 h
h o u r (2 4 h )
1 3
A L A R M S
G a u g e
&lt;
0 .1 0 0
A le r t w h e n th e r a te o f c h a n g e
O k
S to p
-
C a p tu re
O k
-
The view of the date/time configuration window contains selection
lists and numeric fields.
The view of the alarms configuration window contains check boxes
and numeric fields.
Closer description of all fields are discussed in the subsequent
chapters.
18
MC2-IS User Guide
Configuration Windows
Field Types Available for Editing Data
Use the arrow keys ( and ) to move between fields. Start and
stop editing a field with the Enter key ( ).
Fields typically have three modes:
1. The field is displayed, but the cursor is not highlighting that
particular field.
2. The cursor is highlighting a field.
3. The field is in edit mode.
All field presentations include a list of how the field looks in different
states. Some fields do not exactly follow the above mentioned list of
states. The differences are described where applicable.
Numeric Fields
Not highlighted:
N u m e r ic F ie ld
1 0
Highlighted:
1 0
Edit Mode:
1 5
Beside the Enter key ( ), all Numeric keys sets the highlighted
Numeric field to edit mode. The Enter key leaves the previous number
available for editing and the Numeric keys replace the old value.
During edit mode, you can use the arrow keys (
and
), the
F3/Clear and F2/ (= backspace) Function Keys to edit the field.
Accept the new value by pressing the Enter key ( ). To discard
changes, use the F1/Cancel Function Key. See also Part B for
special features concerning numeric fields when generating a signal.
Notes.
Certain numeric fields have an extra tool for inserting a value:
When the field is highlighted, an F2/Capture Function Key appears.
This allows you to capture and save the measured value in the
Numeric field.
Numeric field used for generating/simulating signals include
additional editing possibilities: Spinning and Manual Stepping.
More of them in part B, page 52.
MC2-IS User Guide
19
MC2-IS Firmware
Text Fields
Not highlighted:
T e x t F ie ld
J u s t T e s tin g
Highlighted, empty:
Highlighted, non-empty:
Edit Mode:
J u s t T e s tin g
B o n a F id e
Beside the Enter key ( ), all Numeric keys set the highlighted Text
field to edit mode. The Enter key leaves the previous text available
for editing and the Numeric keys replace the old text.
During edit mode, you can use the arrow keys (
F2/ (= backspace) Function Key to edit the field.
and
) and
Use numeric keys to add characters. Adding characters is done as
follows:
•
•
•
First keypress opens a list of available characters with the first
item highlighted.
Repeated keypresses alter the highlighted characters.
Press the Enter key ( ) or the F3/Select Function Key to
select a character. Additional functionality while the list of
available characters is open:
• If no key is pressed for a certain time, the Automatic
Adding utility selects the highlighted character (not
used in the list of symbols opening from the decimal
key).
• Pressing F3/Cancel closes the list of available
characters and no character is selected.
The F3/Menu Function Key allows you to do the following tasks:
•
•
•
•
Select whether the added characters are:
Upper Case, Lower Case or Numbers.
Select whether the Automatic Adding of characters is:
Fast or Slow.
Clear the field.
Ok for accepting the edited text.
Accept the new text by pressing the Enter key ( ) or use the
previously mentioned menu option. To discard changes, use the
F1/Cancel Function Key.
20
MC2-IS User Guide
Configuration Windows
Selection Lists
Not highlighted:
Highlighted:
Edit Mode:
S e le c tio n L is t
d d .m m .y y y y
d d .m m .y y y y
d d .m m .y y y y
m m .d d .y y y y
y y y y .m m .d d
The Enter key ( ) changes a selection list to edit mode. A list of
available options appears. If the list can not display all available
items at the same time (not enough room), the list has small arrows
at the top/bottom. This indicates that the list is longer that what is
shown.
Use the arrow keys ( and ) to move between options. The F2
Function Key helps you to scroll longer menu list. It allows you to
quickly jump to the end (Bottom) and beginning (Top) depending
on where in the list you are.
Select one of the options with either the Enter key ( ) or the
F3/Select Function Key. To discard changes, use the F1/Cancel
Function Key.
Some of the selection lists have &quot;favorites&quot; i.e. recently selected
items are moved to the top of the list. This feature is typically
available in longer lists.
Hint.
To quickly jump to an option, use the Numeric keys. The first press
jumps to the closest option starting with the first letter stated above
the Numeric key. Repeated key presses jump to options starting with
subsequent letters stated above the Numeric key.
MC2-IS User Guide
21
MC2-IS Firmware
Check Boxes
Highlighted:
Checked:
Unchecked:
C h e c k B o x
A check box has no edit mode. Once it is highlighted (thicker
borders), the value of the check box can be altered using one of the
following possibilities:
22
The Enter key ( ) toggles the value of the check box.
The Sign key ( ) also toggles the value of the check box.
The Zero key ( ) clears the check box.
The One key ( ) sets the check box.
MC2-IS User Guide
Hardware Modules/Options
MC2-IS Options
MC2-IS includes optional hardware modules. This makes it possible
to buy a calibrator with capabilities according your requirements.
Hardware Modules/Options
Internal Pressure Module
A Barometric Pressure Module option is available for MC2-IS.
Optional Soft Carrying Case
MC2-IS' soft carrying case, type 8042904, is practical when moving
between locations. The carrying case can also be used for
transporting utilities, like:
•
•
•
•
Test hoses, test leads and clips
External Pressure Module
A pressure pump
Charger and its cable
The carrying case is suited for use in normal industrial environment.
Since the case is made of antistatic textile, it may also be used in
hazardous area.
Optional Connection Cable for External Pressure Modules
Needed when connecting External Pressure Modules to MC2-IS.
Optional Thermocouple Mini Plugs
For connecting thermocouples to MC2-IS' T/C, mV connector.
MC2-IS User Guide
23
MC2-IS Options
Other Devices
There are an increasing number of devices that can be used
together with MC2-IS. The following list includes devices that are
already available (valid when this manual was printed):
24
•
Intrinsically Safe External Pressure Modules (EXT-IS and
EXT-s-IS). May be used in hazardous area.
•
External Pressure Modules (EXT and EXT-s). May be used in
safe area only.
•
Calibration hand pump that may be used in hazardous area:
- PGM high pressure pump.
•
Calibration hand pumps that may be used in safe area only:
- PGV vacuum pump and
- PGXH extra high pressure pump.
MC2-IS User Guide
Symbols Used
Safety
The materials of MC2-IS' case withstand normal industrial
conditions. MC2-IS endures shocks with the help of the built in
impact protectors.
Symbols Used
The following symbols concerning electrical safety are used in MC2IS.
Alternating current, AC
Direct current, DC
Caution! See manual for further information
MC2-IS User Guide
25
Safety
Ex Information and Approvals
Please read the separate leaflet entiled (in English) MC2-IS Safety
Information. The leaflet includes the same safety information in
several languages.
Ex Approvals:
ATEX
0537
II 1 G
IEC
Ex ia IIC T4 Ga
(Ta = -10 ? +50 &deg;C)
IECEx VTT 08.0002X
Ex ia IIC T4 Ga
(Ta = -10 ? +50 &deg;C)
VTT 08 ATEX 033X
Safety Precautions and Warnings
MC2-IS calibrator is a precision calibration tool that should be used
by skilled people who have read and understood this User Guide.
Working with MC2-IS involves the usage of pressure and/or
electrical instruments. Be sure to know how to work with these
instruments and how to safely connect/disconnect pressure hoses
as well as electrical test leads clips, etc.
Use MC2-IS only if you are certain of that it can be used safely. Safe
use of MC2-IS is no longer possible if one or more of the following
cases are true:
•
•
•
•
When the case of MC2-IS is evidently damaged
When MC2-IS is not functioning as expected
After prolonged storage in unfavorable conditions
After serious damage during transport
Sometimes it is necessary to use a portable radio transceiver while
working with the calibrator. To prevent calibration errors caused by
the radio frequency interference, keep the radio far (at least 1 meter)
from the calibrator and the circuit under calibration, while sending.
26
MC2-IS User Guide
Safety Precautions and Warnings
General Warnings
Do not use MC2-IS in any other way than as described in this User
Guide.
Use the MC2-IS' battery charger in a non-hazardous indoor location
only and only with Beamex MC2-IS calibrators. When charging, the
environment temperature should be between 0 ? +35 &deg;C
(32 ? 95 &deg;F). If MC2-IS' battery charger is broken, dispose it according
to local waste regulations and order a new charger from Beamex. Do
not connect a broken charger to MC2-IS.
MC2-IS uses a rechargeable Battery Pack. It is considered as
hazardous waste. Dispose used batteries properly according to local
regulations.
Avoid short circuiting the batteries. The short circuit current may cause
burns to you, damage to the device or even fire. Notice, that also new
replacement batteries are shipped in charged state.
Rechargeable batteries may vent small amounts of gas during
recharge. The vented gas mixture may be highly explosive, but
normally it diffuses rapidly into the atmosphere. To avoid danger, use
only the original charger and never recharge in a gas-tight container.
Substitution of components may impair intrinsic safety.
Potential electrostatic charging hazard - see Safety Information.
To prevent ignition of a hazardous atmosphere, batteries must only be
charged on an area known to be nonhazardous.
Warnings Concerning Electrical Measurement and Generation
The measurement and generation terminals of MC2-IS are protected
against over voltage and over current as far as it has been possible
without affecting the accuracy. Do not however connect signals that are
above the measurement range of the selected Function.
There is no galvanic isolation between the connectors on the left side,
the internal pressure module connector and the terminals of the
Temperature/Generate section.
Although there is a galvanic isolation between MC2-IS' Measure and
Temperature/Generate sections, it is for functional purposes only. The
circuits are designed so, that you can connect a voltage source 30
VDC / 215 mA or max. 1 W between any terminals without damaging
the device. However, long exposure to this kind of stress may affect the
accuracy.
Maximum output voltage from MC2-IS' terminals is below 30 V. If you,
however, connect together voltages from the Measure and
Temperature/Generate sections or if you connect external voltages to
MC2-IS, the resulting voltage may be high enough to be hazardous.
MC2-IS User Guide
27
Safety
General Warnings Concerning Pressure Measurement
The pressure T-hose is rated to the maximum pressure of 20 bar at
21&deg;C (290 psi at 70&deg;F). Applying higher pressure can be hazardous.
We recommend the use of the pressure hose set. When using other
hoses and connectors, make sure they are high quality products that
withstand the used pressure.
To avoid damaging the pressure module, use hand tightening only
(max. torque 5 Nm) when connecting the pressure measurement hose
to the pressure module. If the use of tools is required to secure the
connection (typically a pressure module with a pressure range of 20
bar / 300 psi), apply the counterforce with a spanner on the connector
body's hexagonal part.
Always depressurize the system before opening or connecting any
pressure fittings or connectors. Use proper valves for venting the
system. Ensure that all connections are made correctly and that the
hose and the connectors are intact.
The allowed pressure media for internal pressure modules is inert, nontoxic, non-explosive media. External modules have the allowed media
printed on the module's sticker. Using unsuitable pressure media may
destroy the pressure module/calibrator.
Never exceed the maximum pressure of a pressure module. The
internal pressure module's maximum pressure is stated on calibrator's
sticker. The maximum pressure of external modules is stated on
module's sticker and mentioned in the Instruction Booklet that is
provided with the external module.
Never plug a hose with your hands or put hands in front of a gas spray
coming from a leakage. A gas bubble in the blood circulation can cause
death.
28
MC2-IS User Guide
Safety Precautions and Warnings
Warnings Concerning High Pressure
High pressure is always dangerous. Only personnel with good
experience and knowledge of high pressure liquid, air and nitrogen
operations are allowed to work with the module. Read carefully all
these instructions and familiarize yourself with local safety instructions
for high pressure operations before starting the use.
When using gas, the system must not contain any liquid, especially if
you do not know how they may react under pressure. Use of clean air
or nitrogen is recommended as gaseous pressure media. Liquid
pressure media should be preferred when using modules with a
pressure range of 60 bar (30000 psi) or more.
If you use nitrogen, minimize the leak to the atmosphere and take care
of sufficient ventilation. Close the valve of the nitrogen cylinder, when
the system is not in use. Increase in the percentage of nitrogen in the
ambient air may cause unconsciousness and death without warning.
Read carefully the safety instructions for nitrogen and make sure that
the other people in the same space are aware of the danger.
Use of liquid pressure medium is recommended with pressure
measurement modules at higher pressure range. Use water or suitable
hydraulic oil. Check that the used liquid is not aggressive against the
materials used in the transducer or tubing. When using liquid, minimize
the amount of air in the system. So you can minimize the amount of
spilled liquid in case of leakage.
Do not use the same tubing with different liquids or gases.
Check what the local regulations say about construction and use of
pressurized vessels. The regulations normally control construction and
use of systems where the product of the pressure and volume exceeds
a certain limit. The volume of this system depends on the instrument
connected to it.
High pressure gas is dangerous because it can break the container
and the flying splinters may cause injury. Also small leaks of gas may
be dangerous because the high velocity of the leaking gas jet enables
penetration through skin. If a gas bubble gets into the blood circulation,
it can cause death. The leak jet is particularly penetrative, if some liquid
is coming with the gas.
MC2-IS User Guide
29
Disposal of Waste Electrical and Electronic Equipment
Disposal of Waste
Electrical and Electronic
Equipment
Beamex is an environmentally conscious company developing
products with a view to ensure that they are easy to recycle and do
not introduce hazardous materials into the environment.
In the European Union (EU) and other countries with separate
collection systems, waste from electrical and electronic equipment
(WEEE) is subject to regulations.
EU WEEE Directive 2002/96/EC (the WEEE Directive) requires
that producers of electronic equipment are responsible for the
collection, reuse, recycling and treatment of WEEE which the
Producer places on the EU market after August 13, 2005. The
objective of this regulation is to preserve, protect and improve the
quality of the environment, protect human health, and conserve
natural resources.
The symbol on the left is also printed on the product's
sticker. It indicates that this product should be handed
over to applicable collection point for the recycling of
electrical and electronic equipment.
For more detailed information about recycling of this product, please
contact your local representative or your waste disposal service.
30
MC2-IS User Guide
Firmware Update
Service
Only qualified service personnel may perform higher level
maintenance for MC2-IS. Never open the case unless have
explicit instructions from Beamex or a local representative.
There are, however a few things that anyone using MC2-IS may do.
Firmware Update
The quickest way to see if a new firmware version is available is
checking out Beamex's web site (http://www.beamex.com). Go to
the “Downloads” page and see what it says about MC2-IS firmware
versions and downloads.
All you need is a Personal Computer and the Computer
communication cable that connects MC2-IS to one of the USB ports
in your PC. For USB driver info, see chapter PC Communication on
page 14 of this manual.
Also check for possible release notes accompanying the updated
file.
The Battery Charger
The charger is not intended to be serviced. When unusable it can be
thrown away according to local waste disposal regulations.
Resetting MC2-IS
Sometimes you may want to reset the calibrator. To do that, press
and hold the Enter key ( ) and the On/Off key ( ) for 5 seconds.
Then press the On/Off key again.
MC2-IS User Guide
31
Service
Recalibrating MC2-IS
Please contact Beamex for details on recalibrating MC2-IS.
Cleaning MC2-IS
If MC2-IS needs cleaning, use cloth soaked with a mild solution of
tall oil soap (pine soap). Wait a few minutes and then clean using a
cloth moistened with pure water. Never use any strong detergents.
32
MC2-IS User Guide
Startup and Basic
Operation
Things discussed in Part B:
• What happens during the startup
procedure.
• Measuring signals.
• Generating/simulating signals.
• Presenting the utilities available
in a window's Tools menu.
Starting MC2-IS
Starting MC2-IS
Startup Procedure
When MC2-IS is started, a startup picture appears. After a self test,
a welcome screen appears displaying some basic information of the
calibrator at hand.
2 2 .0 1 .2 0 0 8 0 9 :3 6 :2 2
W E L C O M E
M o d e l
S N :
V e r s io n
M C 2 -IS
2 0 0 8 0 2 5 2
3 .0 2
Illu m in a tio n s In c ., W o r k s h o p 2
C a lib r a tio n d u e in 2 9 d a y s
C o n tra s t
.
W a it
C o n tin u e
.
If you want to view the calibrator information for a longer period,
press the F2/Wait Function Key. Then the calibrator information is
visible until you press the F3/Continue Function Key.
The lowermost row displays the days until (or since) MC2-IS' due
date for recalibration. If the calibration is overdue, or in the near
future, MC2-IS stops at the welcome screen to remind you of the
need for recalibration. Otherwise it continues to Basic Mode after a
while (or when you press the F3/Continue Function Key).
34
MC2-IS User Guide
Basic Mode, Defined
Basic Mode, Defined
All measurements/generations/simulations are performed in the
Basic Mode. When returning from MC2-IS' higher level operations
(e.g. calibrator and window configurations), you always return to the
Basic Mode.
In Basic Mode, the two available measurement/generation/simulation windows have default settings based either on factory
settings or settings defined when MC2-IS was previously used.
The Function Keys at the bottom of the window allow you to change
the settings of the two windows or open a menu for higher level
operations etc.
Below is an example picture of a MC2-IS screen with the following
settings.
Window :
Pressure measurement using an external pressure module.
Minimum and maximum value display on the additional info row.
High limit alarm in use, but not active ( ).
Low limit alarm in use and active ( ).
Window :
Current measurement using an external power supply.
Bar graph active on the on the additional info row.

0 3 .1 2 .2 0 0 7
b a r
m A
0 .1 0 1
4
MC2-IS User Guide
S e tu p
8
1 1 :1 0 :2 2
G a u g e
1 .3 4 5
E X T
2 .5 7 4
S u p p ly : O ff
1 0 .3 4 5
1 2
S e tu p
1 6
2 0
M e n u
35
Starting MC2-IS
What can be done in Basic Mode
•
•
•
•
•
•
•
Measure signals
Generate signals
Simulate signals
Set alarm limits
Start special measurements (min/max value etc.)
Use the ramping function
Use the stepping function
Next…
Measuring on page 37
Generating/Simulating on page 51
Tools Menu on page 64
Alarms on page 66
36
MC2-IS User Guide
Basic Mode, Defined
Measuring
MC2-IS is capable of performing the following measurement
functions:
•
•
•
•
•
•
•
•
•
Current measurement
Frequency measurement
Pressure measurement
(using an external pressure module)
Pulse counting
Switch state sensing
Voltage measurement
Resistance measurement
RTD temperature measurement
T/C temperature measurement
To start measuring a certain quantity, configure one of the Basic
State's windows (select F1/Setup or F2/Setup ). Use the Enter
key to open to the list of Functions (uppermost field in the
configuration window) and select what you want to measure. All
other fields refine the measurement characteristics.
When presenting measurements in this manual, the first paragraph
describes the measurement followed by the Function setting
needed to start that particular measurement.
Notes.
In this manual, MC2-IS' measurement Functions are presented in
alphabetic order. The order the Functions appear on your MC2-IS
depends on which Functions have been used most recently.
A Function, or a set of Functions, using the same terminals can not
be selected for several windows simultaneously. MC2-IS limits the
list of available Functions based on Functions already in use. To free
terminals, select No Function for appropriate window.
MC2-IS User Guide
37
Measuring
Measurement settings including all alarms and other special
measurements may be saved and retrieved. Use the utility found in
the F3/Menu Function Key for saving and retrieving settings. This is
described in Part C of this manual.
Read the warnings found in chapter Safety
subchapters in Part A, page 24 and onwards.
38
and
its
MC2-IS User Guide
Current Measurement
Current Measurement
MC2-IS supports current measurement using either MC2-IS as the
loop power supply while at the same time measuring the current or
simply measuring the current while an external power supply is
used.
Function:
Current Meas., Supply On or
Current Meas., Supply Off
Make sure the polarity of your connections is correct. The following
pictures present the correct connections depending on whether
MC2-IS is used for providing loop supply or not.
Information concerning current measurement parallel to a test diode
can be found in part C, chapter Current Measurement Parallel to a
Test Diode, Connections on page 112.
Next…
Current Sink on page 54.
Current Generation on page 55.
Tools Menu on page 64.
Alarms on page 66.
Calibration, see Part D.
MC2-IS User Guide
39
Measuring
Frequency Measurement
MC2-IS measures frequencies between 0.0027 Hz (10 cph) to 50
kHz.
Function:
Frequency Measurement
Also check the Trigger Level setting. There you can specify the
trigger level and whether to use a test voltage during the frequency
measurement.
The following picture displays the active terminals:
T e m p e r a t u r e /
II 1
G e n e r a t e
M e a s u r e
G
R , R T D
V , I,
R
V , I,
m e a s
s e n s e
T / C
m V
U i: 3 0
V , Ii: 2 1 5
m A , P i: 1
W
Next…
Frequency Generation on page 56
Switch State Sensing on page 46
Pulse Counting on page 44
Calibration, see Part D.
40
MC2-IS User Guide
Pressure Measurement
Pressure Measurement
MC2-IS is able to measure absolute pressure using its optional
internal barometric pressure module. Using external pressure
modules allows measuring gauge pressures or absolute pressures.
Absolute pressure measurement with external gauge pressure
modules is possible in the following situations:
•
•
For all external pressure modules:
Always, provided the optional internal barometric pressure
module is present.
Additionally, for high pressure modules:
By manually entering the barometric pressure.
When connecting an external pressure module to MC2-IS, it is
automatically detected and there is a possibility to immediately put
the connected external pressure module to use.
Function:
Pressure External or,
Internal Barometer
Also check the Pressure Type setting. For more information
concerning pressure types, see chapter Pressure Type on page
102.
P re s s u re
E x te rn a l
MC2-IS User Guide
41
Measuring
Notes.
For more information on pressure measurement and pressure
modules, see chapter Things to Consider when Measuring
Pressure on page 102.
For information on creating custom pressure units, see Part C,
chapter Custom Pressure Units on page 100.
Connecting and Disconnecting External Pressure Modules
An external pressure module may be connected and disconnected at
any time. If a removed module was part of an active measurement,
MC2-IS emits a &quot;bleep&quot; to inform you of the fact that the external
pressure module used for pressure measurement was removed. The
window where the external pressure measurement was configured
reverts to &quot;None/No Function&quot;.
External Barometric Module Specifics
If MC2-IS includes an internal barometric pressure module and an
external barometric module is connected, the following rules apply:
Connecting: When the external barometric module is
connected to MC2-IS, it supersedes the internal barometric
module.
Disconnecting: When the external barometric module is
removed, any measurements utilizing it are stopped. Restarting
the measurement takes the (possible) internal barometric
module in use.
Warning!
IS compliant external pressure modules (EXT-IS and EXT-s-IS)
are the only external pressure modules to be used in hazardous
area. However, in safe area, non-IS EXT modules may also be
used.
42
MC2-IS User Guide
Pressure Measurement
Zeroing a Pressure Module
If the selected gauge pressure module does not display zero gauge
pressure when the applied pressure is zero, the module has to be
zeroed.
Open the appropriate window setup menu (F1/Setup or
F2/Setup ) and select F1/Zero Pressure.
NOTE!
Zeroing a pressure module is especially important when the
operating position of MC2-IS is changed or the location of
MC2-IS is changed in the vertical direction. Both of the above
mentioned factors affect notably on the pressure measurement
modules. Measuring pressure below 100 mbar (approx. 40 iwc)
should be done with a firmly mounted MC2-IS / EXT Module
(e.g. placed on a table top).
Next…
Tools Menu on page 64
Alarms on page 66
Calibration, see Part D.
MC2-IS User Guide
43
Measuring
Pulse Counting
Function:
Pulse Counting
Check the Trigger Level setting to specify the trigger level and
whether to use a test voltage during the pulse counting. Also check
the Trigger Edge (Rising or Falling) setting so it suits your need.
The following picture displays the active terminals:
T e m p e r a t u r e /
II 1
G e n e r a t e
M e a s u r e
G
R , R T D
V , I,
R
V , I,
m e a s
s e n s e
T / C
m V
U i: 3 0
V , Ii: 2 1 5
m A , P i: 1
W
The counter may be cleared (zeroed) by selecting F1/Setup or
F2/Setup (depending on which window is used for pulse counting)
and F1/Clear Pulses.
Next…
Pulse Generation on page 57
Frequency Generation on page 56
Frequency Measurement on page 40
Switch State Sensing on page 46
Calibration, see Part D.
44
MC2-IS User Guide
Resistance Measurement
Resistance Measurement
Function:
Resistance Measurement
The following picture displays the active terminals:
T e m p e r a t u r e /
II 1
M e a s u r e
G
R , R T D
V , I,
T / C
m V
G e n e r a t e
U i: 3 0
R
V , I,
m e a s
s e n s e
V , Ii: 2 1 5
m A , P i: 1
W
The two leftmost terminals are used in 2-wire systems. MC2-IS
automatically checks the connection and displays the found wiring
system (2-wire, 3-wire or 4-wire) in the upper right corner of the
measuring window. For more information concerning wiring options,
see Resistance and RTD Measurement, Connections on page
110.
Note.
If the measured resistance value is infinite or very high (&gt; 4000
ohm), the text &quot;+OVER&quot; is displayed in the measuring window. This
means that the circuit is broken or the connection is wrong. Wrong
connection may also cause erroneous reading, typically too low. If
necessary, use the 2-wire ohm measurement to check the wiring
before final connection.
Next…
Resistance Simulation on page 58
Temperature Measurement (RTD) on page 48
Tools Menu on page 64
Alarms on page 66
Calibration, see Part D.
MC2-IS User Guide
45
Measuring
Switch State Sensing
MC2-IS is capable of detecting switch's state both when the switch is
free of external potential and switches with DC voltages within the
range -1 V to +30 V.
Function:
Switch
Also check the Trigger Level setting. There you can specify
whether to use only a trigger voltage level or do you also want MC2IS to include a test voltage to detect switches with no external
potential. All voltages below the trigger level are treated as a closed
contact and all voltages above the trigger level are treated as an
open contact.
The following picture displays the active terminals:
T e m p e r a t u r e /
II 1
G e n e r a t e
M e a s u r e
G
R , R T D
V , I,
R
V , I,
m e a s
s e n s e
T / C
m V
U i: 3 0
V , Ii: 2 1 5
When switch state sensing is
selected, the extra row info of
the window with the Switch
Function is capturing measurement values of the other window
every time the switch changes
its state. In the adjoining screen
shot, the switch's current state is
&quot;open&quot; (the big switch symbol).
The last time the switch opened,
the pressure was 3.058 bar and
the last time the switch closed,
the pressure was 1.983 bar.
m A , P i: 1

W
0 8 .1 0 .2 0 0 7
b a r
0 9 :5 5 :2 2
G a u g e
3 .3 4 5
E I NX T
S w itc h
3 .0 5 8
.
S e tu p
S e tu p
1 .9 8 3
M e n u
.
Notes.
The accuracies of the captured values depend greatly on the change
rate of the switch's input signal.
Hint!
Switch state detection may also be used for binary signal detection.
An open switch equals &quot;1&quot; or true&quot; and a closed switch equals &quot;0&quot; or
&quot;false&quot;.
46
MC2-IS User Guide
Switch State Sensing
Use Switch Sound field to assign an &quot;alarm&quot; to a switch. Then you
can use switch test for conductivity/continuity tests with no need to
look at the display.
You can invert the switch's open/closed state indication using the
check box available in the measurement window's setup window.
This can be used to show real switch state when switch state
sensing is connected to relay coil instead of relay contacts.
Next…
Tools Menu on page 64
Alarms on page 66
Calibration, see Part D.
MC2-IS User Guide
47
Measuring
Temperature Measurement (RTD)
Function:
RTD Sensor Measurement
Also check the Sensor setting. Make sure you select the same
sensor type than what is connected to MC2-IS. Otherwise your
measurement results are unreliable.
The picture below displays the active terminals.
The two leftmost terminals are
used in 2-wire systems. MC2-IS
automatically checks the
connection and displays the found
wiring system (2-wire, 3-wire or 4wire) in the upper right corner of
the measuring window.
T e m p e r a t u r e /
II 1
M e a s u r e
G
R , R T D
V , I,
T / C
m V
G e n e r a t e
U i: 3 0
R
V , I,
m e a s
s e n s e
V , Ii: 2 1 5
m A , P i: 1
W
For more information concerning wiring options, see Resistance
and RTD Measurement, Connections on page 110.
By default the additional info row at the bottom of the window
displays the measured RTD resistance. More of additional info row
on page 85.
Note.
If the measured resistance value is infinite or very high
(&gt; 4000 ohm), the text &quot;+OVER&quot; is displayed in the measuring
window. This means that the circuit is broken or the connection is
wrong. Wrong connection may also cause erroneous reading,
typically too low. If necessary, use the 2-wire ohm measurement to
check the wiring before final connection.
Next…
RTD Sensor Simulation on page 59
Resistance Simulation on page 58
Temperature Measurement (Thermocouple) on page 49
Resistance Measurement on page 45
Tools Menu on page 64
Alarms on page 66
Calibration, see Part D.
48
MC2-IS User Guide
Temperature Measurement (Thermocouple)
Temperature Measurement (Thermocouple)
Function:
T/C Sensor Measurement
Make sure a temperature unit is selected from the Unit list.
Otherwise the measurement displays voltages, not temperatures.
Check the Sensor setting. Make sure you select the same sensor
type than what is connected to MC2-IS. Otherwise your
measurement results are unreliable.
Also select a suitable Reference Junction compensation method
from the RJ Mode list. Wrong reference junction setting results in
useless measurement results.
Additional information about
Reference Junction compensation
methods can be found in chapters
Internal Reference Junction on
page 105 and
External Reference Junction on
page 106.
T e m p e r a t u r e /
II 1
G e n e r a t e
M e a s u r e
G
R , R T D
V , I,
T / C
m V
U i: 3 0
R
m e a s
s e n s e
V , Ii: 2 1 5
m A , P i: 1
V , I,
W
The picture above displays the active terminals.
By default the additional info row at the bottom of the window
displays either the thermovoltage corresponding to Reference
Junction temperature 0&deg;C (when Unit field is set to temperature) or
the thermovoltage with Reference Junction compensation taken into
account (when Unit field is set to &quot;Voltage + RJ&quot;). In both cases also
the Reference Junction temperature is shown. More of additional
info row on page 85.
Warning!
If you connect an RTD sensor to the RTD connectors, there is
no galvanic isolation between the thermocouple and the RTD
sensor.
Next…
Thermocouple Simulation on page 61
Temperature Measurement (RTD) on page 48
Voltage Measurement on page 50
Tools Menu on page 64
Alarms on page 66
Calibration, see Part D.
Problems with thermovoltage measurement? See Error situations on page 109.
MC2-IS User Guide
49
Measuring
Voltage Measurement
MC2-IS has two voltage measurement ranges:
Measurement range: -1 to +30 VDC
Function:
Voltage Measurement
The active terminals for this
measurement range are highlighted in
the adjacent picture.
T e m p e r a t u r e /
II 1
G e n e r a t e
M e a s u r e
G
R , R T D
V , I,
R
V , I,
m e a s
s e n s e
T / C
m V
U i: 3 0
V , Ii: 2 1 5
m A , P i: 1
W
Measurement range: -25 to 150 mVDC
Function:
Low-Voltage
Measurement
The active terminals for this
measurement range are highlighted in
the adjacent picture.
T e m p e r a t u r e /
II 1
M e a s u r e
G
R , R T D
V , I,
T / C
m V
G e n e r a t e
U i: 3 0
R
V , I,
m e a s
s e n s e
V , Ii: 2 1 5
m A , P i: 1
W
Warning!
Do not apply hazardous voltages to MC2-IS' terminals. Read the
warnings found in chapter Safety and its subchapters in
Part A, page 24 and onwards.
Next…
Voltage Generation on page 63.
Temperature Measurement (Thermocouple) on page 49.
Tools Menu on page 64.
Alarms on page 66.
Calibration, see Part D.
50
MC2-IS User Guide
Voltage Measurement
Generating/Simulating
MC2-IS is capable to perform the following generation/simulation
Functions:
•
•
•
•
•
•
•
Current generation (sink)
Frequency generation
Pulse generation
Resistance simulation
RTD sensor simulation
Thermocouple simulation
Voltage generation
To start generating/simulating a certain quantity, configure one of the
Basic State's windows (select F1/Setup or F2/Setup ). Use the
Enter key to open to the list of Functions (uppermost field in the
configuration window) and select what you want to
generate/simulate. All other fields refine the generation/simulation
characteristics.
When presenting generations/simulations in this manual, the first
paragraph describes the measurement followed by the Function
setting needed to start that particular generation/simulation.
Notes.
In this manual, MC2-IS' generation/simulation Functions are
presented in alphabetic order. The order the Functions appear on
your MC2-IS depends on which Functions have been used most
recently.
A Function or a set of Functions using the same terminals can not be
selected for several windows simultaneously. MC2-IS limits the list of
available Functions based on Functions already in use. To free
terminals, select No Function for appropriate window.
Read the warnings found in chapter Safety
subchapters in Part A, page 24 and onwards.
MC2-IS User Guide
and
its
51
Generating/Simulating
Changing the Generated/Simulated Value
The simplest way of changing a
generated/simulated
value
is
entering a new value using the
numeric keys. Finish entering the
new value by pressing the Enter
( ) key.
When entering the value, the
Function Keys allow you to clear
the value ( ), remove a character
to the left of the cursor ( ) or
cancel the entering of a new value
( ).
V
2 1 .0 9 .2 0 0 5
0 9 :5 3 :2 2
6 .5
N o n e
C a n c e l
C le a r
Spinning and Manual Stepping
Spinning and Manual Stepping are two easily available methods for
changing the generated/simulated value.
To start Spinning, press the Enter
( ) key when generating/simulating and viewing the Basic Mode
windows. Then one of the generation/simulation digits is inverted.
To spin the inverted digit, use the
up and down arrow keys (
).
To change the digit to be spinned,
or
Function Key.
press either
V
2 1 .0 9 .2 0 0 5
6 .5 1 0 0
N o n e
S te p
To stop spinning, press the Enter
( ) key.
Manual Stepping is an additional
functionality
available
while
Spinning.
To start Manual Stepping, you first
need to start the Spinning utility
and then press the F2/Step
Function Key.
To step through the defined steps,
use the up and down arrow keys
(
). To toggle between the
minimum and maximum value,
Function Key.
press the
52
0 9 :5 8 :2 2
V
2 9 .0 8 .2 0 0 5
1 4 :5 8 :2 2
9 .0 0 0 0
N o n e
C lo s e
0 %
S e ttin g s
MC2-IS User Guide
Changing the Generated/Simulated Value
opens a Manual Step configuration window. Its
Function Key
functionality is described in chapter Manual Stepping on page 75.
To stop Stepping and return to Spinning, press the Enter ( ) key.
To stop Stepping and return to Basic Mode, press the F1/Close
Function Key.
Notes.
You cannot exceed the minimum/maximum limits of a Function when
Spinning/Stepping.
The spinned/stepped value follows the resolution properties of the
generated/simulated Function.
MC2-IS remembers the Manual Step configuration settings for each
generation/simulation Function.
MC2-IS User Guide
53
Generating/Simulating
Current Sink
MC2-IS has a possibility to sink current, i.e. MC2-IS acts as a device
controlling the flow of current while an external device generates the
supply voltage for the loop. The maximum current is 25 mA.
Function:
Current Generation
The picture below presents the connections and the active terminals
in MC2-IS:
T e m p e r a t u r e /
II 1
G e n e r a t e
e a s u r e
G
R , R T D
V , I,
T / C
m V
M
U i: 3 0
R
V , Ii: 2 1 5
P o w e r
S u p p ly
V , I,
m e a s
s e n s e
m A , P i: 1
W
In s tru m e n t
to b e
c a lib r a te d
Note.
If the loop resistance of the external circuit is too high or infinite, the
message &quot;Overload&quot; is displayed until the load is reasonable.
Warnings!
Make sure that you don't exceed the maximum current allowed
by the instrument under test.
If you open the current generation loop, the calibrator still tries
to maintain the current. If you then close the loop again, the
current is first too high, but returns quickly to the correct level.
If this current peak could damage the components of the loop,
make sure that the loop will not open or protect it against
overcurrent. For the same reason, always enter 0 mA output
before connecting the loop.
Next…
Current Generation on page 55
Current Measurement on page 39
Tools Menu on page 64.
Stepping on page 70
Ramping on page 73
Calibration, see Part D.
54
MC2-IS User Guide
Current Generation
Current Generation
Although MC2-IS does not have a single Function allowing you to
generate current, it can be realized by combining two Functions as
follows:
In one window, set the Function
to Current Meas., Supply On
and in the other window, set the
Function to
Current Generation
In the adjacent picture, window 1
is set to measure current with 24
Volt power supply on. Window 2
is set to sink current thus
controlling the current.
The connection should be as
follows:
Next…
Current Sink on page 54
Current Measurement on page 39
Tools Menu on page 64
Stepping on page 70
Ramping on page 73
Calibration, see Part D.
MC2-IS User Guide
55
Generating/Simulating
Frequency Generation
The generated frequency is either a positive or an amplitude
symmetric square wave.
Function:
Frequency Generation
Check the Waveform setting. The percentage value is the Duty
Cycle setting (the ratio of the output high time to the total cycle
time). Also check the Amplitude setting.
The adjacent picture displays the
active terminals:
T e m p e r a t u r e /
II 1
M e a s u r e
G
R , R T D
V , I,
T / C
m V
G e n e r a t e
U i: 3 0
R
m e a s
s e n s e
V , Ii: 2 1 5
m A , P i: 1
V , I,
W
Note.
Due to technical reasons, the entered Duty Cycle setting is not
always realized. This happens with relatively high and low
frequencies. The true Duty Cycle percentage is shown in the
appropriate Basic Mode window.
See Appendix 1, Technical Data for more specific info of Duty
Cycle limitations.
Next…
Pulse Generation on page 57.
Frequency Measurement on page 40.
Tools Menu on page 64.
Stepping on page 70
Ramping on page 73.
Calibration, see Part D.
56
MC2-IS User Guide
Pulse Generation
Pulse Generation
The generated pulses are either positive or amplitude symmetric
square waves.
Function:
Pulse Generation
The Repetition Frequency (Hz) setting defines the frequency to be
used when generating the pulses.
The Waveform and Amplitude settings are similar to the settings
found in Frequency Generation on page 56.
The adjacent picture displays the
active terminals:
T e m p e r a t u r e /
II 1
M e a s u r e
G
R , R T D
V , I,
T / C
m V
G e n e r a t e
U i: 3 0
R
V , I,
m e a s
s e n s e
V , Ii: 2 1 5
m A , P i: 1
W
In the Basic Mode window:
Enter the amount of pulses MC2-IS should generate. The pulse
generation starts immediately after the amount is entered.
By default the additional info row at the bottom of the window
displays pulses done and pulses left (icons: and respectively).
More of additional info row on page 85.
Note.
Due to technical reasons, the entered Duty Cycle setting is not
always realized. This happens with relatively high and low
frequencies. The true Duty Cycle percentage is shown in the
appropriate Basic Mode window.
See Appendix 1, Technical Data for more specific info of Duty
Cycle limitations.
Next…
Frequency Generation on page 56.
Pulse Counting on page 44.
Tools Menu on page 64.
Stepping on page 70
Ramping on page 73.
Calibration, see Part D.
MC2-IS User Guide
57
Generating/Simulating
Resistance Simulation
In resistance simulation MC2-IS mimics a resistor. The instrument
under test generates the current for the resistance measurement.
MC2-IS controls the voltage across its terminals so that the
resistance (voltage to current ratio) corresponds to the resistance.
Function:
Resistance Simulation
The correct resistance value is
between the resistance simulation
terminals of the calibrator. Use only
the two leftmost R, RTD terminals with
every wiring option. Connect the
possible third and fourth wire
according to the requirements of the
connected instrument.
T e m p e r a t u r e /
II 1
G e n e r a t e
M
e a s u r e
G
R , R T D
V , I,
R
V , I,
m e a s
s e n s e
T / C
m V
U i: 3 0
V , Ii: 2 1 5
m A , P i: 1
W
Notes.
In resistance simulation MC2-IS monitors the resistance
measurement current. If the current is too high, it cannot simulate
the right resistance value. In that case it shows the message &quot;High
Cur&quot;.
Accurate operation of the simulation electronics requires that the
current supplied by the instrument under test does not vary rapidly.
The simulation result is not accurate if the instrument under test
uses AC current. If the instrument under test uses pulsed
measurement current, it should wait a few milliseconds before
starting the measurement after setting the current.
Next…
Resistance Measurement on page 45.
RTD Sensor Simulation on page 59.
Tools Menu on page 64.
Stepping on page 70
Ramping on page 73.
Calibration, see Part D.
58
MC2-IS User Guide
RTD Sensor Simulation
RTD Sensor Simulation
In RTD sensor simulation MC2-IS mimics an RTD. The instrument
under test generates the current for the RTD measurement. MC2-IS
controls the voltage across its terminals so that the resistance
(voltage to current ratio) corresponds to the simulated temperature.
Function:
RTD Sensor Simulation
Also check the Sensor setting. Make sure you select the same
sensor type than the connected instrument requires. Otherwise your
simulation is useless.
The correct resistance value is
between the resistance simulation
terminals of the calibrator. Use only
the two leftmost R, RTD terminals with
every wiring option. Connect the
possible third and fourth wire
according to the requirements of the
connected instrument.
T e m p e r a t u r e /
II 1
G e n e r a t e
M
e a s u r e
G
R , R T D
V , I,
R
V , I,
m e a s
s e n s e
T / C
m V
U i: 3 0
V , Ii: 2 1 5
m A , P i: 1
W
By default the additional info row at the bottom of the window
displays the resistance MC2-IS is simulating while performing RTD
simulation. More of additional info row on page 85.
MC2-IS User Guide
59
Generating/Simulating
Notes.
In RTD simulation MC2-IS monitors the resistance measurement
current. If the current is too high, it cannot simulate the right
resistance value. In that case it shows the message &quot;High Cur&quot;.
Accurate operation of the simulation electronics requires that the
current supplied by the instrument under test does not vary rapidly.
The simulation result is not accurate if the instrument under test
uses AC current. If the instrument under test uses pulsed
measurement current, it should wait a few milliseconds before
starting the measurement after setting the current.
Next…
Temperature Measurement (RTD) on page 48.
Thermocouple Simulation on page 61.
Resistance Simulation on page 58.
Tools Menu on page 64.
Stepping on page 70
Ramping on page 73.
Calibration, see Part D.
60
MC2-IS User Guide
Thermocouple Simulation
Thermocouple Simulation
In thermocouple simulation the original thermocouple is
disconnected from the instrument under test and replaced with MC2IS. MC2-IS mimics a thermocouple at given temperatures. To the
instrument under test MC2-IS appears as a thermocouple at the
given temperature.
Function:
T/C Sensor Simulation
Check the Sensor setting. Make sure you select the same sensor
type than what is required by the instrument under test. Otherwise
your measurement results are unreliable.
Also select a suitable Reference Junction compensation method
from the RJ Mode list. Wrong reference junction setting results in
useless measurement results. Additional information about
Reference Junction compensation methods can be found in chapters
Internal Reference Junction on page 105 and
External Reference Junction on page 106.
The adjacent picture displays the
active terminals:
T e m p e r a t u r e /
II 1
M
e a s u r e
G
R , R T D
V , I,
T / C
m V
G e n e r a t e
U i: 3 0
R
V , I,
m e a s
s e n s e
V , Ii: 2 1 5
m A , P i: 1
W
By default the additional info row at the bottom of the window
displays either the thermovoltage corresponding to Reference
Junction temperature 0&deg;C (when Unit field is set to temperature) or
the thermovoltage with Reference Junction compensation taken into
account (when Unit field is set to &quot;Voltage + RJ&quot;). In both cases also
the Reference Junction temperature is shown. More of additional
info row on page 85.
Notes.
If the resistance of the external circuit in thermocouple simulation is
very low (obvious short circuit), the message &quot;Overload&quot; is
displayed until the load is reasonable.
If the thermocouple to be simulated is not available MC2-IS' sensor
list, select one of the &quot;Voltage + Reference Junction&quot; units and
convert from temperature to millivolts manually. Also select a
thermocouple type from the Sensor list that approximately matches
your sensor (in used Reference Junction range). This allows MC2-IS
to perform Reference Junction compensation as accurately as
MC2-IS User Guide
61
Generating/Simulating
possible. In this situation, the accuracy depends on the similarity of
the selected sensor in MC2-IS and the used sensor.
Wire-wound thermocouple temperature indicators and
recorders are calibrated with known loop resistance, commonly ten
or twenty ohms. The required resistance of the conductors is usually
marked on the device. When calibrating such a device, tune the loop
resistance to the nominal value with an additional resistor.
Use MC2-IS' 2-wire resistance measurement to tune the loop
resistance of a wire wound device. Short circuit the measuring
device for the time of resistance measurement. The resistance
measurement may damage the device, if you do not install the short
circuit. For more information on resistance measurement, see
chapter Resistance Measurement on page 45.
Warnings!
If you short circuit the thermocouple simulation output, MC2-IS
tries to maintain the voltage by increasing the output current. If
you then open the output again, the voltage is first too high, but
returns quickly to the correct level. If this voltage peak could
damage the components of the circuit, make sure that the
circuit can not be shorted or protect the circuit against
overvoltage. For the same reason, always enter 0&deg;C output
before connecting the circuit.
If you connect an RTD sensor to the R, RTD connectors, there is
no galvanic isolation between the thermocouple and the RTD
sensor.
Next…
Temperature Measurement (Thermocouple) on page 49.
RTD Sensor Simulation on page 59.
Tools Menu on page 64.
Stepping on page 70
Ramping on page 73.
Calibration, see Part D.
Problems with thermovoltage simulation? See Error situations on page 109.
62
MC2-IS User Guide
Voltage Generation
Voltage Generation
MC2-IS has two voltage generation ranges as presented here.
Generation range: -3 to 11 V
Function: Voltage Generation
The active terminals for this
generation range are highlighted in
the adjacent picture.
T e m p e r a t u r e /
II 1
G e n e r a t e
M e a s u r e
G
R
R , R T D
V , I,
T / C
m V
U i: 3 0
m e a s
s e n s e
V , Ii: 2 1 5
m A , P i: 1
V , I,
W
Generation range: -25 to 150 mV
Function: Low-Voltage Generation
The active terminals for this
generation range are highlighted in
the adjacent picture.
T e m p e r a t u r e /
II 1
M
e a s u r e
G
R , R T D
V , I,
T / C
m V
G e n e r a t e
U i: 3 0
R
m e a s
s e n s e
V , Ii: 2 1 5
m A , P i: 1
V , I,
W
Warning!
If you short circuit the voltage output, MC2-IS tries to maintain
the voltage by increasing the output current. If you then remove
the short circuit, the voltage is first too high, but returns quickly
to the correct level. If this voltage peak could damage the
components of the circuit, make sure that the circuit can not be
shorted or protect the circuit against over voltage. For the same
reason, always enter 0 V output before connecting the circuit.
Next…
Voltage Measurement on page 50.
Thermocouple Simulation on page 61.
Tools Menu on page 64.
Stepping on page 70
Ramping on page 73.
Calibration, see Part D.
MC2-IS User Guide
63
Tools Menu
Tools Menu
MC2-IS' Basic Mode windows have utilities that add extra features to
your measurements/generation/simulations. They are available in a
window's Tools menu. The contents of the Tools menu varies
depending on which Function is selected. This is because
measurement
Functions
require
different
tools
than
generation/simulation Functions.
Tools menu for a measurement Function:
W IN D O W
F u n c tio n

S E T U P
W IN D O W
F u n c tio n
P re s s u re E x te rn a l
U n it
b a r
P re s s u re T y p e
G a u g e
Z e ro
P re s s u re
T o o ls
O k

S E T U P
P re s s u re E x te rn
F u n c tio n In fo ...
U n it
A la r m s ...
k P a
D a m p in g ...
P re s s u re T y p e
L e a k / S ta b ility
A D b i ss op ll ua ty e M o d e /
S h o w A d d itio n a
Z e ro
P C r e a s n s c u e r le
a l
T e s t...
S p e c ia ls ...
l In fo ...
T o o ls
B o tto m
O k
S e le c t
Tools menu for a generation/simulation Function:
W IN D O W
F u n c tio n

S E T U P
W IN D O W
F u n c tio n
R T D S e n s o r S im u la tio n
U n it
&deg;C
S e n s o r
P t1 0 0 a 3 8 5
T o o ls
64
O k

S E T U P
R T D S e n s o r S im u la tio n
F u n c tio n In fo ...
U n it
S te p ...
k P a
R a m p ...
P re s s u re T y p e
M a n u a l S te p (
)...
A D b i ss op ll ua ty e M o d e / S p e c i a l s . . .
S h o w A d d itio n a l In fo ...
Z e ro
P C r e a s n s c u e r le
T o o ls
B o tto m
O k
S e le c t
MC2-IS User Guide
Function Info
The following subchapters present each utility available in the Tools
menu.
Function Info
Function Info option is always available in the Tools menu.
This option is &quot;enhancing your measurement&quot; by presenting some
useful information of the selected quantity, e.g. the measurement
range and calibration info. Function Info is divided into two pages.
Use F2/More Function Key to move from page to page.
To see Function Info, enter the following menu commands:
F1/Setup or F2/Setup (depending on which window you want to
view Function Info for), F2/Tools and Function Info from the
opened menu.
MC2-IS User Guide
65
Tools Menu
Alarms
Each main measurement in a window may have alarm limit settings.
MC2-IS supports &quot;higher than&quot;, &quot;lower than&quot;, &quot;high rate&quot; and &quot;low
rate&quot; alarms.
To set the alarm limits, enter the following menu commands:
F1/Setup or F2/Setup (depending on which window you want to
configure alarms to), F2/Tools and Alarms from the opened menu.
Make sure the Alarms Active field is checked. Then the other
settings are available. Table of alarm symbols used:
High alarm limit
Low alarm limit
High change rate alarm limit
Low change rate alarm limit
Individual alarm limit values may also be activated/deactivated using
the check box preceding the alarm limit value. The alarms chosen
for use are shown in the measurement window using the same
symbols as in the table above.
When an alarm limit is exceeded, MC2-IS emits an audible alarm
and the alarm symbol is shown with inverted colors. To acknowledge
the alarm, open the window's setup window and from it the Tools
menu. Just below the menu's Alarm option is an item that is shown
only when alarms are activated: Acknowledge this Alarm. The active
alarm limit is inverted in the measurement window as long as the
alarm limit is exceeded.
Note.
Rate alarm limits are not &quot;symmetrical&quot;. E.g. high rate alarm
0.5 bar/min emits an alarm when the pressure increases faster that
the limit but does not emit an alarm when the pressure decreases
faster than -0.5 bar/min.
66
MC2-IS User Guide
Damping
Hint.
If you want to set an alarm that utilizes the change rate alarm limit
but don't know which limit value to use, display the change rate on
the additional info row (see chapter Display Mode and Special
Measurements on page 78). Observe what happens to the change
rate during the event that need an alarm. Then set the change rate
alarm limit accordingly.
Acknowledging Alarms
When an alarm is active, the Tools menu of the window with the
active alarm includes an option to acknowledge alarms.
Resetting Alarms and Alarm Limits
To stop using alarm limits, uncheck the Alarms Active field.
To stop using and clear all alarm limits, select another Function or
reselect the same Function.
Damping
Damping is useful when a measurement signal contains unwanted
noise. MC2-IS includes a set of damping tools.
Average filters the data using the average of recent measurements.
Adaptive average uses the measurement's change rate to choose
the amount of recent measurements used in the average calculation.
The next group of options are 1st order digital filters with a damping
time as stated in their names.
To set the damping value, enter the following menu commands:
F1/Setup or F2/Setup (depending on which window you want to
configure damping to), F2/Tools and Damping from the opened
menu. The damping settings apply to all main and secondary
measurements active in the window when damping was started.
MC2-IS User Guide
67
Tools Menu
Leak/Stability Test
Leak/stability test is a tool for testing the leak or stability of, e.g. a
pressure measurement system. Generally: the test tells you both the
absolute decrease and the average decrease per minute of any
measurement during the test period.
To open the test window, enter the following menu commands:
F1/Setup or F2/Setup (depending on which window you want to
configure the test to), F2/Tools and Leak / Stability Test from the
opened menu.
See the leftmost picture below to see how the test window appears.
The window where the test was invoked in is moved to top and
enlarged to include the test data and the other window is minimized
showing only the essential measurement data. Any data selected to
be shown on the additional info row is temporarily hidden.
0 8 .1 0 .2 0 0 7

1 3 :0 5 :2 2
L E A K / S T A B IL IT Y T E S T
G a u g e E X T
k P a
4 9 .3
C lo s e
.
1 0 .8 6
+ 3 0 s

2 4 V
S ta rt
1 3 :0 6 :2 2
L E A K / S T A B IL IT Y T E S T
G a u g e E X T
k P a
4 9 .2
s
3 0
m A
0 8 .1 0 .2 0 0 7
m A
C lo s e
0 .1
3 0
s
0 .2 /m in d u r in g 3 0 s
1 0 .8 6
2 4 V
+ 3 0 s
S to p
.
To start the test, first check the test time to be used. Either accept
the default value or enter another time period in seconds. Entering
zero as the test time means the test will continue until manually
stopped. Select F1/Start and see how the test advances.
The rightmost picture above is an example of an MC2-IS display
during a test. The absolute decrease is shown beside the triangle
and the average decrease per minute below.
68
MC2-IS User Guide
Leak/Stability Test
Notes.
You may increase the test time in 30 second steps using the
F2/+30 s Function Key. This can be done both before the test is
started and also while the test is in progress.
MC2-IS uses numbers that have more decimals than are available
on the display. In some cases these extra digits may cause rounding
that differs from values that are shown on display. Notable
differences between shown and manually calculated values usually
mean that MC2-IS' accuracy is not suitable for the given task.
If applicable, disable MC2-IS' auto-off functionality during the test. If
the test lasts longer than the auto-off delay, MC2-IS is shut down
while the test is still incomplete.
An external pressure module (EXT) connected to MC2-IS during a
leak/stability test cannot be taken into use in the window were the
leak/stability test is under progress.
Hint.
If you have a pressure transmitter connected to a pressure
measurement system and you want to check the pressure decrease
without altering the pressure connections, do as follows:
Connect the electrical output of the pressure transmitter to MC2-IS.
Use MC2-IS' scaling utility to scale the output signal back to
pressure units. Start the leak/stability test for the scaled
measurement and there you can see the leak in pressure units.
More info on scaling in chapter Scaling on page 83.
MC2-IS User Guide
69
Tools Menu
Stepping
Stepping utility is one of three tools allowing you to create
generation/simulation signals that vary with time. This one could be
called &quot;automatic stepping&quot; since one of the other tools is a manual
stepping utility.
Other similar tools:
Ramping on page 73
Manual Stepping on page 75.
To open the stepping configuration window, enter the following menu
commands: F1/Setup or F2/Setup (depending on which
window you want to configure the stepping to), F2/Tools and Step
from the opened menu.
The leftmost picture below shows the configuration window and the
rightmost picture the stepping utility in use.
V
R a n g e (0 %
0 .0 0 0 0
S T E P
V
IN T
3 .0 0 0 0
... 1 0 0 % )
... 9 .0 0 0 0
5
S te p T im e , s
0
R e p e a ts (0 = &yen; )
.
1 4 :5 8 :2 2
6 .0 0 0 0
N o n e
R e p e a t F o rm a t
C l o s e 5 . 9 C 6 a p O t u u r te p u t S t a r t
2 9 .0 8 .2 0 0 5
.
S e tu p
S e tu p
M e n u
Start stepping by selecting the F3/Start Function Key in the
configuration window. To stop a stepping that is in progress, open
the stepping configuration window and press F3/Stop Function Key.
When stepping is ready, or stopped, you may restart it as follows:
F1/Setup or F2/Setup (depending on which window you want to
configure the stepping to), F1/Start Step. This possibility is available
until a new Function is selected for the window where stepping was
used or MC2-IS is shut down.
70
MC2-IS User Guide
Stepping
The following table presents the fields of the configuration window.
FIELD
DESCRIPTION/OPTIONS
Range(*
The minimum and maximum value for the
stepping range.
Step Time
Enter the time for a single step. Use only
full seconds, no decimals.
Repeats
Defines how many times the steps are
repeated. Value &quot;zero&quot; equals continuous
stepping.
Repeat Format
How the stepping should be done.
Available options:
Up / Down
Down / Up
Up
Down
Step Definition
Defines how the stepping is done
Available options (with no custom sets):
By: 'Step Size'
By: 'Number of Steps'
3: 50 %
5: 25 %
6: 20%
11: 10 %
0%&gt;10&gt;25&gt;50&gt;75&gt;90&gt;100
0%&gt;2&gt;4&gt;50&gt;96&gt;98&gt;100
0%&gt;5&gt;40&gt;100
-2%&gt;0&gt;2&gt;4&gt;50&gt;96&gt;98&gt;100&gt;102
Create New…
The two first options require additional
data that is entered in the two following
fields.
The group of sets starting with a number
and colon are sets with fixed step sizes.
The first number is the amount of step
levels and the percentage value is the
step size.
The group of sets starting with a number
and percentage symbol are sets with
varying step sizes (suitable for, e.g. valve
tests). Each number is a step level.
The last item in the list allows you to
make your own custom step definition.
Custom steps are presented in chapter
Custom Test Point Sets on page 95.
Continues on next page5
MC2-IS User Guide
71
Tools Menu
FIELD (cont.)
DESCRIPTION/OPTIONS
Step Size
Active only if Step Definition field is set to
&quot;By: 'Step Size'&quot;. If applicable, set the fixed
step size here.
Number of Steps
Active only if Step Definition field is set to
&quot;By: 'Number of Steps'&quot;. If applicable, set
the number of steps here.
Transfer Function
Defines the input/output correlation.
Available options:
Linear
√x
√x3
√x5
x2
Create New…
The last item in the list allows you to make
your own custom Transfer Function.
Custom Transfer Functions are presented
in chapter Custom Transfer Functions on
page 97.
*)Warning!
Do not configure the range settings so that they exceed the allowed input range of the connected instrument. MC2-IS
determines the limits of the range settings based on the
selected quantity and port, not the connected instrument.
72
MC2-IS User Guide
Ramping
Ramping
Ramping utility is one of three tools allowing you to create
generation/simulation signals that vary with time.
Other similar tools:
Stepping on page 70
Manual Stepping on page 75
To open the ramping configuration window, enter the following menu
commands: F1/Setup or F2/Setup (depending on which
window you want to configure the ramping to), F2/Tools and Ramp
from the opened menu. Note that ramping is available for
generation/simulation Functions only.
The leftmost picture below shows the configuration window and the
rightmost picture the ramping utility in use.
R A M P
V
V
IN T
9 .0 0 0 0
R a n g e (0 %
0 .0 0 0 0
... 1 0 0 % )
... 9 .0 0 0 0
.
W a it in 0 %
0 .0 0 0
R is e T im e
u t S ta rt
C l o s e 5 . 9 C 6 a p O t u u r te p
1 5 :2 5 :2 2
4 .5 3 2 0
N o n e
R e p e a t F o rm a t
0 .0 0 0
2 9 .0 8 .2 0 0 5
.
S e tu p
S e tu p
M e n u
Start ramping by selecting the F3/Start Function Key in the
configuration window. To stop a ramp that is in progress, open the
ramping configuration window and press F3/Stop Function Key.
When ramping is ready, or stopped, you may restart it as follows:
F1/Setup or F2/Setup (depending on which window you want to
configure the ramping to), F1/Start Ramp. This possibility is
available until a new Function is selected for the window where
ramping was used or MC2-IS is shut down.
MC2-IS User Guide
73
Tools Menu
The following table presents the fields of the configuration window.
FIELD
DESCRIPTION/OPTIONS
Range(*
The minimum and maximum value for the
ramping range.
Repeat Format
Wait in 0%
Rise Time
Wait in 100%
Fall Time
How the ramp should be carried out.
Use only full seconds, no decimals.
Repeats
Defines how many times all four phases
of the ramp are repeated. Value &quot;zero&quot;
equals continuous ramping.
*)Warning!
Do not configure the range settings so that they exceed the allowed input range of the connected instrument. MC2-IS
determines the limits of the range settings based on the
selected quantity and port, not the connected instrument.
Note.
MC2-IS actually makes the ramp in small steps. The steps are as
small as possible, slower ramps use smaller steps.
74
MC2-IS User Guide
Manual Stepping
Manual Stepping
Manual stepping differs from the other two tools allowing you to
create varying generation/simulation signals in that the signal does
not automatically change. Instead it advances according to the
defined steps when you press the up or down arrow keys (
), one
step at a time.
Other similar tools:
Stepping on page 70
Ramping on page 73
To open the manual stepping configuration window, enter the
following menu commands: F1/Setup or F2/Setup (depending
on which window you want to configure the stepping to), F2/Tools
and Manual Stepping from the opened menu. Note that manual
stepping is available for generation/simulation Functions only.
The leftmost picture below shows the configuration window and the
rightmost picture the stepping utility in use.
V
M A N U A L S T E P (
R a n g e (0 %
0 .0 0 0 0
)
V
IN T
3 .0 0 0 0
... 1 0 0 % )
... 9 .0 0 0 0
2 6 .0 9 .2 0 0 5
1 4 :0 4 :2 2
6 .0 0 0 0
N o n e
S te p D e fin itio n
B y &quot;N u m b e r o f S te p s &quot;
3 .0 0 0 0
C lo s e
.
S te p S iz e
C a p O t u u r te p u t
S ta rt
C lo s e
1 0 0 %
S e ttin g s
.
Start manual stepping by selecting the F3/Start Function Key in the
configuration window. To stop it, press F1/Close Function Key (in
Basic Mode).
MC2-IS User Guide
75
Tools Menu
The following table presents the fields of the configuration window.
FIELD
DESCRIPTION/OPTIONS
Range(*
The minimum and maximum value for the
stepping range.
Step Definition
Defines how the stepping is done
Available options (with no custom sets):
By 'Step Size'
By 'Number of Steps'
3: 50 %
5: 25 %
6: 20%
11: 10 %
0%&gt;10&gt;25&gt;50&gt;75&gt;90&gt;100
0%&gt;2&gt;4&gt;50&gt;96&gt;98&gt;100
0%&gt;5&gt;40&gt;100
-2%&gt;0&gt;2&gt;4&gt;50&gt;96&gt;98&gt;100&gt;102
Create New…
The two first options require additional
data that is entered in the two following
fields.
The group of sets starting with a number
and colon are sets with fixed step sizes.
The first number is the amount of step
levels and the percentage value is the
step size.
The group of sets starting with a number
and percentage symbol are sets with
varying step sizes (suitable for, e.g. valve
tests). Each number is a step level.
The last item in the list allows you to
make your own custom step definition.
See Custom Test Point Sets on page
95.
Step Size
Active only if Step Definition field is set
to &quot;By: 'Step Size'&quot;. If applicable, set the
fixed step size here.
Number of Steps
Active only if Step Definition field is set
to &quot;By: 'Number of Steps'&quot;. If applicable,
set the number of steps here.
Continues on next page5
76
MC2-IS User Guide
Manual Stepping
FIELD (cont.)
DESCRIPTION/OPTIONS
Transfer Function
Defines the input/output correlation.
Available options:
Linear
√x
√x3
√x5
x2
Create New…
The last item in the list allows you to
make your own custom Transfer
Function.
See
Custom
Transfer
Functions on page 97.
*)Warning!
Do not configure the range settings so that they exceed the allowed input range of the connected instrument. MC2-IS
determines the limits of the range settings based on the
selected quantity and port, not the connected instrument.
See also:
Spinning and Manual Stepping on page 52.
MC2-IS User Guide
77
Tools Menu
Display Mode and Special Measurements
The Display Mode and Special Measurements utility is always
available, but the available options vary depending on the selected
Function.
All Display Mode settings are in: F1/Setup or F2/Setup (depending on which window you want to change the display mode
for), F2/Tools. Select Display Mode / Specials from the opened
menu.
When certain Display Modes or Special Measurements are active,
the measurement window displays a warning ( ) to indicate that the
reading is not the actual measured value. Depending on the selected
Display Mode or Special Measurement, some additional text is also
shown.
All Display Mode and Special Measurement settings revert to
Normal display mode if you select another quantity. Additionally, the
same menu were a Display Mode or a Special Measurement was
invoked also includes a possibility to revert back to Normal Display
Mode.
Note applying to all display modes and special measurements.
While performing display mode and/or special measurement
calculations, MC2-IS uses numbers that have more decimals than
are available on the display. In some cases these extra digits may
cause rounding that differs from values that are shown on display.
Notable differences between shown and manually calculated values
usually mean that MC2-IS' accuracy is not suitable for the given
task.
78
MC2-IS User Guide
Display Mode and Special Measurements
Error %
Error Percentage display compares the measurements of the two
windows based on entered measurement range values. The window
the Error Percentage display was invoked from is considered the
&quot;output&quot; of the instrument and the other window the &quot;input&quot;.
The Error Percentage value is shown in the &quot;output&quot; window and the
actual &quot;output&quot; signal is by default shown on the additional info row
as seen in the rightmost picture.
k P a
E R R O R %
G a u g e
.9 8 In p u t
0
In p u t R a n g e (0 %
0 .0 0 0
...
E IXN T T
... 1 0 0 % )
1 0 0 .0 0 0
T r a n s fe r F u n c tio n
L in e a r
m A
S to p
.
5 .
2 4 V
9 C 6 a p O t u u r te p u t O k
When Error Percentage display is active, the words &quot;Error %&quot; is
displayed.
To configure the error percentage display (and also the other types
of error displays) you need to enter input and output range values to
both windows.
In addition to the range you may also set the Transfer Function
(Input/Output relationship). Default value is: Linear.
The display resolution may also be edited, if needed.
Notes.
If anything else was selected for display on the additional info row,
the main measurement of the Error percentage window replaces the
previous additional info data.
Also: if you select two other items to be displayed on the additional
info row while an error display is active, the second item replaces the
windows' main measurement data. Beware of the problems that
may result in not seeing the true measurement value.
For help on making Custom Transfer Functions, see Part C,
chapter Custom Transfer Functions on page 97.
MC2-IS User Guide
79
Tools Menu
Error in Input Units
Error In Input Units display compares the measurements of the two
windows based on entered measurement range values. The window
the Error display was invoked from is considered the &quot;output&quot; of the
instrument and the other window the &quot;input&quot;.
The Error In Input Units value is shown in the &quot;output&quot; window and
the actual &quot;output&quot; signal is shown on the additional info row as seen
in the rightmost picture.

E R R O R IN IN P U T U N IT S
G a u g e E IXN T T
k P a
0 .9 8 In p u t
In p u t R a n g e (0 %
0 .0 0 0
... 1 0 0 % )
1 0 0 .0 0 0
T r a n s fe r F u n c tio n

0 8 .1 0 .2 0 0 7
b a r
1 3 :2 1 :2 2
G a u g e
0 .4 4 8
b a r
E rr / In
0 .0 2
L in e a r
m A
.
S to p 5 .
2 4 V
9 C 6 a p O t u u r te p u t O k
1 0 .8 6
S e tu p
E I NX T
A
S e tu p
M e n u
.
When Error In Input Units display is active, a warning triangle is
shown together with the input unit and the text &quot;Err / In&quot; is shown
above the Error value.
Error displayed in input units is in all other ways similar to error
displayed in error percentage. The only difference is in how the
calculated error is displayed.
For configuration details, refer to Error % on page 79.
80
MC2-IS User Guide
Display Mode and Special Measurements
Error in Output Units
Error In Output Units display compares the measurements of the two
windows based on entered measurement range values. The window
the Error display was invoked from is considered the &quot;output&quot; of the
instrument and the other window the &quot;input&quot;.
The Error In Output Units value is shown in the &quot;output&quot; window and
the actual &quot;output&quot; signal is shown on the additional info row as seen
in the rightmost picture.
E R R O R IN O U T P U T U N IT S
G a u g e E IXN T T
k P a
0 .9 8 In p u t
In p u t R a n g e (0 %
0 .0 0 0
... 1 0 0 % )
1 0 0 .0 0 0
T r a n s fe r F u n c tio n

0 8 .1 0 .2 0 0 7
b a r

0 .4 4 8
m A
.
S to p 5 .
2 4 V
9 C 6 a p O t u u r te p u t O k
E X T
E rr / O u t
L in e a r
m A
1 3 :2 2 :2 2
G a u g e
1 0 .8 6
S e tu p
-0 .3 1
A
S e tu p
M e n u
.
When Error In Output Units display is active, a warning triangle is
shown together with the input unit and the text &quot;Err / Out&quot; is shown
above the Error value.
Error displayed in input units is in all other ways similar to error
displayed in error percentage. The only difference is in how the
calculated error is displayed.
For configuration details, refer to Error % on page 79.
MC2-IS User Guide
81
Tools Menu
Percentage
Percentage display compares the measured/generated/simulated
value against an entered range (0 % and 100 %).
When measuring, the measured value is replaced by the Percentage
value. The measurement value in engineering units is shown on the
additional info row as seen in the rightmost picture.
When generating/simulating, the Percentage is the editable value
and the generated/simulated value in engineering units is shown on
the additional info row.

P E R C E N T D IS P L A Y
G a u g e
m A
1 0 .8 6
In p u t R a n g e (0 %
4 .0 0 0
IN T
... 1 0 0 % )
2 0 .0 0 0
T r a n s fe r F u n c tio n
L in e a r
D is p la y R e s o lu tio n
S to p
C a p tu re
O k
When Percentage display is active, the letter &quot;%&quot; is displayed and
the text &quot;Scaled&quot; is shown above the Percentage value.
To configure the percentage display, enter input range values for the
selected quantity.
In addition to the range you may also set the Transfer Function
(Input/Output relationship). The display resolution may also be
edited, if needed.
Notes.
If anything else was selected for display on the additional info row,
the main measurement of the window with percentage display
replaces the previous additional info data.
Also: if you select two other items to be displayed on the additional
info row while Percentage display is active, the second item replaces
the windows' main measurement data. Beware of the problems
that may result in not seeing the true measurement value.
For help on making Custom Transfer Functions, see Part C,
chapter Custom Transfer Functions on page 97.
82
MC2-IS User Guide
Display Mode and Special Measurements
Scaling
In Scaling a measured/generated/simulated value may be converted
to whatever &quot;quantity&quot; is needed, provided the conversion
information is known.
When measuring, the measured value is replaced by the scaled
value. The actual measurement value in engineering units is shown
on the additional info row as seen in the rightmost picture.
When generating/simulating, the scaled value is the editable one
and the generated/simulated value in engineering units is shown on
the additional info row.
m A
S C A L IN G
G a u g e
1 0 .8 6
In p u t R a n g e (0 %
4 .0 0 0
IN T

2 1 .0 9 .2 0 0 4
N o n e
... 1 0 0 % )
2 0 .0 0 0
T r a n s fe r F u n c tio n

G a llo n s /m in
S to p
C a p tu re
... 1 0 0 % )
O k
S c a le d
1 2 3 .6 7
L in e a r
S c a le d R a n g e ( 0 %
1 1 :1 6 :2 2
1 0 .8 6
S e tu p
A
S e tu p
M e n u
When Scaling display is active, the entered unit (or the text &quot;scaled
unit&quot; if the unit was not entered) is displayed after a warning triangle
and the text &quot;Scaled&quot; is shown above the Scaled value.
To configure Scaling, enter Input Range values for the selected
quantity, set the Transfer Function, enter the Scaled Range and
the Unit of the scaled range. The display resolution may also be
edited, if needed.
Notes.
If anything else was selected for display on the additional info row,
the main measurement of the window replaces the previous
additional info data.
Also: if you select two other items to be displayed on the additional
info row while Scaling display is active, the second item replaces the
windows' main measurement data. Beware of the problems that
may result in not seeing the true measurement value.
For help on making Custom Transfer Functions, see Part C,
chapter Custom Transfer Functions on page 97.
MC2-IS User Guide
83
Tools Menu
Deviation
Deviation measurement compares a measured value against an
entered reference value. The reference value is subtracted from the
reading of the measured value. The difference replaces the
measurement value. Both the reference value (indicated with a
triangle) as well as the actual measurement value (indicated with a
circled A) are shown on the additional info row as seen in the
picture.
D E V IA T IO N M E A S U R E M E N T
G a u g e
IN T
m A
1 0 .8 6

M e a s u r e D e v ia tio n fr o m
1 0 .0 0 0
S to p
C a p tu re

O k
2 1 .0 9 .2 0 0 4
N o n e
m A
D e v ia tio n
0 .8 6 0 0
1 0 .0 0 0 0
S e tu p
1 1 :1 7 :2 2
S e tu p
1 0 .8 6
M e n u
A
When Deviation measurement is active, text &quot;Deviation&quot; is shown
above the Deviation value.
Hint.
Use the F2/Capture Function Key to add a measured &quot;tare&quot; as the
reference value.
Notes.
If anything else was selected for display on the additional info row,
the main measurement of the window replaces the previous
additional info data.
Also: if you select two other items to be displayed on the additional
info row while Deviation measurement is active, the second item
replaces the windows' main measurement data. Beware of the
problems that may result in not seeing the true measurement
value.
Warning.
Keep in mind that when the displayed deviation reading is small
compared to the actual reading, a significant part of the
deviation value may be measurement error. See the
specifications for measurement errors at the actual
measurement level.
84
MC2-IS User Guide
Showing Data on the Additional Info Row
Showing Data on the Additional Info Row
As presented in section A's User Interface chapter, both Basic Mode
windows have an Additional Info row for showing additional data.
Each window may have two values shown on their respective
Additional Info rows. The only exception is the bar graph option. It
reserves the whole Additional Info row alone.
All Additional Info Row settings are in: F1/Setup or F2/Setup (depending on which window you want to change the display mode
for), F2/Tools. Select Show Additional Info from the opened
menu.
The data available to be shown on the Additional Info row can be
divided into following groups:
Data that is Always Available.
Can be selected to be shown at any time.
Display Mode and Special Measurement Related Data.
Data that is available to be shown depending on Display Mode
and Special Measurement settings.
Function Dependent Data.
Data that is available for certain Functions, e.g. barometric
pressure when it is needed.
The following chapters present the data available to be shown on the
Additional Info row. Any limitations as to when the data is available
are mentioned where applicable. Below each heading is the icon or
unit displayed on the Additional Info row when that particular
Additional info is shown.
MC2-IS User Guide
85
Tools Menu
Maximum value
Displays the found maximum value after a measurement was started
or it was reset.
Minimum value
Displays the found minimum value after a measurement was started
or it was reset.
Rate of Change Value (unit 1/min)
Displays the calculated rate of change value (units/min) found after a
measurement was started or the calculation was reset.
Maximum - Minimum
&plusmn;
Calculates the difference between the maximum and minimum
measurement value found after a measurement was started or it was
reset.
Cumulative Average
x
Calculates the cumulative average of measurements after a
measurement was started or it was reset.
Cumulative average means that, after the calculation is started,
every new measurement is included in the average calculation. Thus
the amount of measurements included in the cumulative average
increases all the time and the average value's change rate typically
gets smaller with time.
Internal Temperature
&deg;C,
&deg;F or
K
When an internal or an external pressure module is used in a
window, the internal temperature of the pressure module can be
selected to be shown.
Normal Reading
A
Normal Reading refers to the window's main measurement. It is
available when the following Special Measurements reserve
window's main value: All Error Display Modes as well as
Percentage, Scaling and Deviation measurement.
Deviation Reference
Available when deviation measurement is active. This is the entered
reference value MC2-IS uses to calculate the measurement's
deviation from.
86
MC2-IS User Guide
Showing Data on the Additional Info Row
Barometric Pressure
PB
Displays the barometric pressure value that is used for
measurement’s pressure type conversion. This value comes usually
from built-in barometer, but some high-pressure modules may allow
using manually entered barometer value.
Feedback Measurement
V, mV, &micro;V,
mA, &micro;A,
&deg;C, &deg;F or K
Available for the following generation/simulation Functions:
(same unit as
main value)
Voltage Generation
Low-Voltage Generation
T/C Sensor Simulation
Current Source or Sink
When MC2-IS generates voltages or current, it uses its own
measurement Functions to control the generated value. This
feedback measurement may be displayed on the Additional Info row.
Thermovoltage, RJ = 0&deg;C
㎷0
Displays the thermovoltage for reference junction temperature 0&deg;C.
Suitable for referring to thermovoltage table values. Available for T/C
Sensor Measurement and T/C Sensor Simulation Functions with
temperature unit selected.
Thermovoltage
㎷
Displays the actual measured thermovoltage for reference junction
temperature. Available for T/C Sensor Measurement and T/C
Sensor Simulation Functions.
RJ Temperature
&deg;C,
&deg;F or
K
Displays the temperature of the reference junction in use. Available
for T/C Sensor Measurement and T/C Sensor Simulation
Functions.
Sensor Resistance
Ω
MC2-IS User Guide
Displays the real resistance MC2-IS is measuring or simulating for
an RTD sensor Function.
87
Tools Menu
Pulses Done
Displays the pulses currently done during Pulse Generation.
Pulses Left
Displays the pulses currently left to be done during Pulse
Generation.
Bar Graph
0
1 0
2 0
3 0
4 0
-5
-2 .5
0
2 .5
5
A Bar Graph is always available in the list of
Additional Info row data, but the type of Bar Graph
depends on the Display Mode and Special
Measurement settings. The bar graph is always
related to the main value (big numbers) and its units,
so configure the Bar Graph's range accordingly.
If any of the Error Display Modes is active, the Bar
Graph displays a graphical presentation of the error
value. The middle of the graph represent zero error
and the symmetrical &quot;width&quot; of the graph is user
configurable
Resetting and Clearing Additional Info Row / Calculations
Active minimum, maximum, rate of change, maximum – minimum
and cumulative average calculations may be reset using the
additional option found in the window's Tools menu: Reset Min /
Max / Rate.
Changing the Function for a window sets all Additional Info data to
default values (usually nothing).
Activating a Display Mode or a Special Measurement often replaces
them with data related to the activated Display Mode or Special
Measurement. Any previously activated minimum, maximum or rate
of change calculations are still working, but are no longer shown
(until selected to be shown again).
88
MC2-IS User Guide
Advanced Operation and
Configurations
Things discussed in Part C:
• Advanced tools found in the
Utilities Menu.
• Help on how to create
customized test point sets and
transfer functions.
• Related information:
Useful during pressure
measurement, thermocouple
measurement/simulation and
resistance/RTD
measurement/simulation.
Utilities Menu
Utilities Menu
This chapter and its subchapters present items available in the
utilities menu that opens from Basic Mode by pressing F3/Menu.
About MC2-IS
Opens a window presenting basic information of MC2-IS.
.
.
Pressure module, if installed, is mentioned below the Free Memory
information.
90
MC2-IS User Guide
User Setups for Window 1 &amp; 2
User Setups for Window 1 &amp; 2
MC2-IS supports saving user settings for window and window .
The available free memory defines how many user settings may be
saved.

0 8 .1 0 .2 0 0 7
m A

S a v e
k R P ea s t o
P re s s
S c a lin
T a re &amp;
S C A e a v t u nb p cr y e u t l
1 3 :4 6 :2 2
2 4 V
5 .4 9 7 5
/ R e m o v
re P re -O
u re X M T
g fo r T a
N e t u s in
e S
F FG
R E
n k 1
g D
e tu p ...
S a e u t g t i e n g sE X T
rr %
0 2 L e v e l
e v ia tio n
1 2 .3
N S B e o d t ut e t po r s m v t a
S M V e e &auml;l e n l jc u t
2 3 .0 8 .2 0 0 5
1 2 :4 5 :2 2
S A V E / R E M O V E S E T U P
S e le c t Ite m
C re a te N e w ...
S a v e a s
L e a k T e s t S e tu p fo r P T 3 2 3 .1
C a n c e l
M e n u
S a v e
In the leftmost picture above, three User Setups are already saved.
Selecting Save / Remove Setup option opens the SAVE / REMOVE
SETUP window allowing you to save the current settings for window
and window (see rightmost picture).
About the second item on the list shown in the leftmost picture
above: Restore Pre-OFF Settings:
MC2-IS' startup is made as straight forward as possible. It does not
automatically restore its more advanced functions (display mode,
special measurements etc.) used when MC2-IS was shut off. By
selecting the Restore Pre-OFF Settings option, it is possible to
restore MC2-IS' advanced functions used before it was last shut off.
MC2-IS User Guide
91
Utilities Menu
Date/Time
Allows you to select the displayed date and time formats according
to your needs. This window is also used to set date and time. Use
the day, month, year and hour (24), min, sec fields to set the
date/time.
D A T E / T IM E
D a te F o rm a t
d d .m m .y y y y
d a y
1 0
m o n th
8
y e a r
2 0 0 4
T im e F o r m a t
h h .m m .s s 2 4 h
h o u r (2 4 h )
1 3
m in
4 5
s e c
2 2
C lo s e
Notes.
The time must always be given in the 24 hour format no matter what
the configured time format is.
Date and time will be updated when you press the F3/Ok Function
Key.
92
MC2-IS User Guide
General Settings
General Settings
This window allows you to edit the
following settings:
G E N E R A L S E T T IN G S
L a n g u a g e
E n g lis h ( B u ilt In )
A u to - o ff D e la y ( 0 = n e v e r )
0
C a lib r a to r [m in ]
G e n e r a l T e m p e r a tu r e U n it
&deg;C
T e m p e r a tu r e S c a le
C o n tra s t
FIELD
Language
MC2-IS User Guide
O k
NOTES
Contains a list of User Interface languages.
Auto-off Delay:
Calibrator [min]
Back light [min]
Wait time before auto power off is
executed and before the display light is
automatically switched off. See also notes
found after this table.
Value 0 (zero) means the Auto-off delay is
disabled.
General
Temperature Unit
Select either &deg;C (Centigrade) or &deg;F
(Fahrenheit) as the temperature unit.
Temperature Scale
Contains a list of standard temperature
scales.
Key Click Volume,
Alarm Volume,
Attention Volume,
Outside Span
Volume and,
Error Volume
Available options (apply to all volume
settings):
Off, Low, Medium and High.
Net Frequency
Options:
50 Hz and 60 Hz.
Note that wrong net frequency setting
affects the accuracy of MC2-IS.
Owner
A text field for entering owner's name etc.
This data is shown in the Welcome Screen.
93
Utilities Menu
Notes.
All changes in general settings become valid immediately except
when changing the language. To activate the new language, shut off
and restart MC2-IS.
Disable auto-off delay during long-time tasks (e.g. leak/stability test).
Otherwise the auto-off functionality interrupts the task.
When calibrator's Auto-off delay is in use (value other than zero), a
warning dialog pops up 30 seconds before the auto power off
executes. In the dialog the Function Keys have the following options:
F1/Cancel
Cancels the auto power off feature for the moment, but it stays
active even during this session.
F2/Stop
Disables the auto power off feature for this session. It will
reactivate when the calibrator is switched on the next time.
F3/Ok
Immediately shuts down the calibrator.
Calibrator Adjustment
Opens a window to start the recalibration and adjustment of MC2-IS.
Please contact Beamex for a details on recalibrating MC2-IS.
0 8 .1 0 .2 0 0 7
1 3 :5 8 :2 2
C A L IB R A T O R A D J U S T M E N T
E n te r p a s s w o r d to e n a b le
*
c a lib r a to r a d ju s tm e n ts
E x t. P re s s u re (E X T 1 0 0 m )
3 6 0
C a lib r a tio n P e r io d
B e a m e x
C a lib r a te d b y
E l. M e a s u r e
94
(E L -M E A S U R E )
O k
MC2-IS User Guide
Calibrator Adjustment
Custom Test Point Sets
MC2-IS has a comprehensive set of pre-entered test point sets
(steps). If however they are not suited for your needs, you can
create your own test points as presented here.
Start the custom test point definition from one of the following utilities
found in generation/simulation functions' Tools menu:
•
•
Stepping presented on page 70,
Manual Stepping presented on page 75 and
One of the utilities' configuration fields is Step Definition combo.
The last option in the combo is Create New. It opens the custom
test point tool. If a custom set already exists, selecting it in the Step
Definition combo also opens the custom test point tool.
Give a name to the Custom test
point set. The Scaled Range
initially has the same range as
defined for the Stepping or Manual
Stepping from where the custom
test step definition was invoked.
You may edit the Scaled Range
according to you own needs during
step definition, e.g. scale the steps
to percentage values.
Enter the point values. Press down
arrow ( ) to add a point below the
last point.
MC2-IS User Guide
E D IT T E S T P O IN T S E T
S e t N a m e
IN T
J u s t T e s t S e t
S c a le d R a n g e ( 0 % ... 1 0 0 % )
4 .0 0 0 0
... 2 0 .0 0 0 0
1 . 4 .0 0 0 0
0 %
2 . 6 .0 0 0 0
1 3 %
3 . 7 .5 0 0 0
C l o s e 5 . 9 6M e O n uu
2 2 %
tp u t S a v e
95
Custom Test Point Sets
The F2/Menu Function Key opens a menu for editing the test point
rows or the whole set. Options:
•
•
•
Insert Row
Delete Row
Delete All Rows
• Copy Set
• Delete Set
The Insert Row option adds a point above the current point.
The F3/Ok Function Key saves the custom test point set and adds it
to the Define Steps combo list. It is located after all pre-entered test
point sets, before the Create New option.
To separate custom point sets from pre entered ones, custom point
sets are prefixed &quot;User:&quot; and the row ends with a chevron pointing
right &quot; &quot;. This indicates that the point set may be edited.
Hints!
The point values need not be in ascending order or even inside the
range limits.
To force MC2-IS to stay in one point for a longer time, enter the
same point value to several successive points.
Notes.
The step values are saved as floating point number percentage
values so the steps may be used for any Function and range. The
percentage values are proportioned to the current Stepping /
Manual Stepping range.
The percentage values shown to the right of the test points are
whole number near values of the entered values. They are for
information only.
The available free memory defines how many custom test points
may be saved. If there is not enough memory left to save a custom
test point set, MC2-IS displays an error message suggesting that
you first free some memory and then retry adding a custom test
point set.
96
MC2-IS User Guide
Calibrator Adjustment
Custom Transfer
Functions
MC2-IS has a pre-entered set of standard transfer functions. If
however they do not suit your needs, you can create your own
transfer functions as presented here.
The custom transfer function definition can be started from the
following Display Modes (found in the Tools menu of measurement
functions):
•
•
•
Error % presented on page 79,
Error in Input Units presented on page 80 and
Error in Output Units presented on page 81.
And from the following Display Modes (always available in the
Tools menu):
•
•
Percentage presented on page 82 and
Scaling presented on page 83.
And also from the Tools menu of the following generation/simulation Function utilities:
•
•
Stepping presented on page 70 and
Manual Stepping presented on page 75.
One of the combos in all of the above mentioned utilities is called
Transfer Function. The last option in the combo is Create New. It
opens the custom transfer function tool. If a custom transfer function
already exists, selecting it in the Transfer Function combo also
opens the custom transfer function tool.
MC2-IS User Guide
97
Custom Transfer Functions
Give a name to the custom
transfer function.
The Input Range and Output
Range fields are scaled ranges for
the custom transfer function.
Default values are for percentage
scaling.
Enter Input/Output pair values in
ascending order. Press down
arrow
( )
to
add
more
Input/Output pairs below the last
Input/Output pair.
E D IT T R A N S F E R F U N C T IO N
IN T
T r a n s fe r F u n c tio n N a m e
In th e C a s e
In p u t R
0 % 0 .0 0
O u tp u t
0 % 0 .0 0
a n g e
1 0 0 %
0 0
R a n g e
1 0 0 %
0 0
In p u t
0 . 0 .0 0 0 0
C lo s e
1 0 0 .0 0 0
1 0 0 .0 0 0
O u tp u t
0 .0 0 0 0
M e O n uu t p u t S a v e
The F2/Menu Function Key opens a menu for editing the
Input/Output pairs or the whole set. Options:
Insert Row
Delete Row
Delete All Rows
Copy Set
Delete Set
The Insert Row option adds an Input/Output pair above the current
Input/Output pair. The new row has default values based on the
Input/Output pairs above and below it (calculated using linear
approximation).
The F3/Ok Function Key saves the custom transfer function and
adds it to the Transfer Function combo list. An inverted copy of
the custom transfer function is also added to the Transfer
Function combo list. The inverted transfer function has a &quot;x-1&quot;
symbol before its name. The custom transfer function and its
inverted copy are located after all pre-entered transfer functions but
before the Create New option.
To separate custom transfer functions from pre entered ones,
custom transfer functions are prefixed &quot;User:&quot; and the row ends with
a chevron pointing right &quot; &quot;. This indicates that the point set may be
edited.
Hint!
The maximum Input/Output pair values may be outside the ranges'
maximum values.
98
MC2-IS User Guide
Calibrator Adjustment
Notes.
The Input/Output pairs are saved as floating point number
percentage values so the transfer function may be used for any
function and range. The percentage values are proportioned to the
current range.
The available free memory defines how many custom transfer
functions and Input/Output pairs may be saved. If there is not
enough memory left to save a custom transfer function, MC2-IS
displays an error message suggesting that you first free some
memory and then retry adding a custom transfer function.
MC2-IS approximates the values between entered input/output pairs
by calculating a curve between a pair of points that connects
smoothly to the adjoining curve. The entered Input/Output pairs need
to be points of a strictly increasing function.
MC2-IS User Guide
99
Custom Pressure Units
Custom Pressure Units
MC2-IS has a comprehensive set of pre-entered pressure units. If
however they are not suited for your needs, you can create your own
custom pressure units.
To define custom pressure units, configure one of the Basic State's
windows (select F1/Setup or F2/Setup ) for pressure
measurement. While configuring, open the Unit combo and select
one of the &quot;User&quot; units. They can be found at the bottom of the list of
pressure units (as long as they are not in use and not selected to the
&quot;favorites&quot; list).
When selecting a user configurable unit, a window opens for
configuring the unit.
Saved custom pressure units can
be seen in the pressure unit list.
To separate them from pre
entered units, they are prefixed
&quot;User:&quot; and the row with a custom
pressure unit ends with a chevron
pointing right &quot; &quot;. This indicates
that the unit may be edited.
U S E R U N IT S E T T IN G S
U s e r U n it N a m e
F P N
F a c to r
7 .1 4
R e fe r e n c e U n it
P a
C a n c e l
O u tp u t
O k
Notes.
Make sure you do not run any tasks found in the Tools menu (e.g
Scaling) while editing a user defined unit. All Tools menu tasks
utilize the user defined unit as it was when starting the task.
To remove a Custom Pressure Unit, open it in User Unit Settings
window and clear User Unit Name field. Then press F3/Ok.
See also Part B, chapter Scaling.
100
MC2-IS User Guide
Calibrator Adjustment
Related Information
Most of the measurements, generations and simulations presented
in this manual are straight forward: Just make the required window
settings and connect the instrument under test to the active
terminals and that's it!
Some cases require additional settings and things to check before
you can be certain that the measurement, generation or simulation
works as expected. A typical example of this is temperature
measurement using a thermocouple. It is not enough to select the
correct Function in MC2-IS. The Sensor type and the Reference
Junction Mode has to be set accordingly, too. Wrong settings give
erroneous results.
Whenever this additional information may be of use in a
measurement, generation or simulation, text describing the Function
refers to one of the following chapters. An experienced may skip this
supplemental text, but for a beginner we highly recommend it.
The subjects described here are:
MC2-IS User Guide
Things to Consider when Measuring Pressure on page 102,
Pressure Type on page 102,
Pressure Modules and their Naming Conventions on
page 103,
Square Rooting on page 104,
Thermocouple Measurement/Simulation, Connections and
Troubleshooting on page 105,
Resistance and RTD Measurement, Connections on
page 110,
Current Measurement Parallel to a Test Diode, Connections
on page 112 and
Parallel Functions in MC2-IS on page 113.
101
Related Information
Things to Consider when Measuring Pressure
General
MC2-IS can measure pressure with its internal pressure module or
with external pressure modules. If a barometric module is present,
the measurement results of other modules can be shown either as
absolute pressure or as gauge pressure.
Pressure Type
Every pressure measurement is in fact a pressure difference
measurement: a given pressure value is compared against a
reference pressure. In certain cases the reference pressure has a
special meaning (like the atmospheric pressure) and the pressure
measurements with reference to against these points are given a
special name:
•
•
•
•
Absolute pressure measurement uses vacuum as the
reference pressure.
Barometric pressure (or atmospheric pressure) is the
absolute pressure of the surrounding atmosphere. It is
specially titled because of its importance.
Gauge pressure measurement uses the atmospheric
pressure as the reference. Gauge pressure may be zero,
negative or positive. Most of MC2-IS' pressure modules
actually measure gauge pressure although they may be used
for measuring other pressure types too.
Differential pressure measurement requires a special
differential pressure module that has an input available for
both the reference pressure and the given pressure.
To be able to measure absolute pressure with external gauge
pressure modules connected to MC2-IS, you need to have an
internal barometric pressure module. Certain high pressure modules
may however approximate absolute pressure measurement by
adding an entered barometric pressure to the measured gauge
pressure.
Always ensure that the pressure type setting of your pressure
measurement is what you intended it to be. The pressure type
setting is crucial for getting meaningful pressure measurement
results.
102
MC2-IS User Guide
Things to Consider when Measuring Pressure
Pressure Modules and their Naming Conventions
MC2-IS' software refer to pressure modules as follows:
EXT200mC-s-IS
which means that there is an instrinsically safe standard accuracy
External Pressure Module connected to MC2-IS. The module has a 200 to +200 mbar (-3 to +3 psi) pressure range.
The names of pressure modules start with the letters EXT. The names
also include numbers and possible additional letters as follows:
•
•
•
•
•
•
The number defines the max. nominal pressure in the SI
pressure unit bar.
If the number is followed by a small &quot;m&quot;, the given max. nominal
pressure is given in mbar.
An additional letter C means the pressure module is a
compound module with an ability to also measure negative
gauge pressures.
An additional letter D means the pressure module is a
differential pressure module (this letter is not shown in the
example above).
The small &quot;s&quot; means the module is a standard accuracy
pressure module. High accuracy modules do not have the small
&quot;s&quot; in their name.
Finally, the letters &quot;IS&quot; means the module is intrinsically safe,
i.e. it may be used in hazardous area. Modules without the
letters &quot;IS&quot; may be used in safe area only.
Examples:
Name
EXT10mD
EXT20C
EXT160
Measurement range
0 I 10 mbar differential
-1 I 20 bar
0 I 160 bar
in psi
0.15
-14.5 I 300
0 I 2400
Notes.
Compound modules with a max. nominal pressure above 1 bar (e.g.
EXT20C) are able to measure negative pressures down to -1 bar.
Compound modules with a max. nominal pressure below 1 bar (e.g.
EXT400mC) are only able to measure as deep negative pressures
as positive pressures.
MC2-IS User Guide
103
Related Information
Square Rooting
Pressure transmitters or converters used for flow measurement often
have square rooting character. Here are a couple of examples on
how you can configure MC2-IS to take into account the instrument's
square rooting character:
1. Set the Display Mode of window that measures the
instrument's output signal to Error Percentage and make sure
√x).
the Transfer Function field is set to Square Rooting (√
2. Use Scaling to convert the instrument's output signal to a
suitable format and again, make sure the Transfer Function
field is set to Square Rooting (√
√x).
Display Modes as well as scaling is discussed in chapter Tools
Menu in part B of this User Guide.
104
MC2-IS User Guide
Thermocouple Measurement/Simulation, Connections and Troubleshooting
Thermocouple Measurement/Simulation, Connections and
Troubleshooting
To accurately measure the thermovoltage caused by the
temperature to be measured, the second thermovoltage caused by
the Reference Junction needs to be compensated. This is done
using one of the Reference Junction compensation methods
described in the subsequent chapters.
The Reference Junction compensation method has to be chosen
both when measuring and simulating thermocouples.
Internal Reference Junction
MC2-IS' Internal Reference Junction makes thermocouple
measurement/simulation easy. No external connections are required; just connect the thermocouple or a thermovoltage receiver
directly to MC2-IS' &quot;T/C&quot; terminals. To select this compensation
method, set the window's Function to field &quot;T/C Sensor
Measurement&quot; or &quot;T/C Sensor Simulation&quot;, make sure the Unit
is a temperature unit and set the RJ Mode field to &quot;Internal&quot;.
Connection when measuring/simulating thermocouples using
Internal Reference Junction Mode:
T /C m a te r ia ls
( T /C , e x te n s io n o r
c o m p e n s a tio n w ir e s )
T /C s e n s o r
o r a
T /C s ig n a l r e c e iv e r
T e m p e r a t u r e /
II 1
G e n e r a t e
M
e a s u r e
G
R , R T D
V , I,
T / C
m V
U i: 3 0
R
V , I,
m e a s
s e n s e
V , Ii: 2 1 5
m A , P i: 1
W
Refer to the Technical Data in Appendix 1 for specifications
concerning the Internal Reference Junction.
See also…
External Reference Junction on page 106
MC2-IS User Guide
105
Related Information
External Reference Junction
When using an external Reference Junction, MC2-IS measures or
simulates the thermovoltage using the &quot;T/C&quot; terminals. The following
external Reference Junction compensation methods are available:
External RTD:
To be used when:
•
The Reference Junction temperature is measured using an
RTD sensor connected to MC2-IS' RTD terminals.
Connection when measuring/simulating thermocouples using
Reference Junction compensation method &quot;External RTD&quot;:
T /C
C o p p e r
m a te r ia ls
T
re f
T /C s e n s o r
o r a
T /C s ig n a l r e c e iv e r
T e m p e r a t u r e / G e n e r a t e
T e m p e r a t u r e / G e n e r a t e
II 1
RR ,, RR TT DD
VV ,, II ,,
T / C
m V
M
e a s u r e
G
U i: 3 0
V , I,
RR mm ee aa ss
ss ee nn ss ee
V , Ii: 2 1 5
m A , P i: 1
W
Warning!
If you connect an RTD sensor to the RTD connectors, there is no
galvanic isolation between the thermocouple and the RTD
sensor.
None (0 &deg;C):
To be used when:
•
•
•
•
106
The Reference Junction temperature is fixed to 0&deg;C (using,
e.g. ice) and MC2-IS is not used for measuring the Reference
Junction temperature.
The Reference Junction temperature is controlled with 0&deg;C
set point.
A compensation box is used and the Reference Junction
temperature setting is 0&deg;C.
There is no Reference Junction compensation in the
measuring/simulation circuit but 0&deg;C is a good enough
approximation.
MC2-IS User Guide
Thermocouple Measurement/Simulation, Connections and Troubleshooting
Manually Entered:
Usable when:
•
•
•
•
The Reference Junction temperature is fixed to a
temperature that differs from 0&deg;C.
The Reference Junction temperature is controlled and the
controller's set point is not 0&deg;C. Note: this method is of use
only if the accuracy of the controller is better than MC2-IS'
own Reference Junction.
A compensation box is used and the Reference Junction
temperature setting is other than 0&deg;C.
There is no Reference Junction compensation in the
measuring/simulation circuit, but you want to manually enter
another Reference Junction temperature than 0&deg;C.
Connection when measuring/simulating thermovoltages using a
temperature controller and either of the following Reference
Junction compensation methods:
&quot;Manually Entered&quot; or &quot;None (0 &deg;C)&quot;:
T e m p e ra tu re
C o n tr o lle r
T /C
T re f
T /C s e n s o r
o r a
T /C s ig n a l r e c e iv e r
MC2-IS User Guide
C o p p e r
m a te r ia ls
T e m p e r a t u r e /
II 1
M
e a s u r e
G
R , R T D
V , I,
T / C
m V
G e n e r a t e
U i: 3 0
R
V , I,
m e a s
s e n s e
V , Ii: 2 1 5
m A , P i: 1
W
107
Related Information
Connection when measuring/simulating thermovoltages using a
fixed temperature and either of the following Reference
Junction compensation methods:
&quot;Manually Entered&quot; or &quot;None (0 &deg;C)&quot;:
T /C
m a te r ia ls
C o p p e r
T re f
T /C s e n s o r
o r a
T /C s ig n a l r e c e iv e r
T e m p e r a t u r e /
II 1
G e n e r a t e
M
e a s u r e
G
R , R T D
V , I,
T / C
m V
U i: 3 0
R
V , I,
m e a s
s e n s e
V , Ii: 2 1 5
m A , P i: 1
W
Connection when measuring/simulating thermovoltages using a
compensation box and either of the following Reference
Junction compensation methods:
&quot;Manually Entered&quot; or &quot;None (0 &deg;C)&quot;:
T /C m a te r ia ls
t
C o p p e r
T /C s e n s o r
o r a
T /C s ig n a l r e c e iv e r
T e m p e r a t u r e /
II 1
G e n e r a t e
M
e a s u r e
G
R , R T D
V , I,
T / C
m V
U i: 3 0
R
V , I,
m e a s
s e n s e
V , Ii: 2 1 5
m A , P i: 1
W
See also…
Internal Reference Junction on page 105
108
MC2-IS User Guide
Thermocouple Measurement/Simulation, Connections and Troubleshooting
Error situations
The easiest way to avoid errors in thermocouple measurement and
simulation is to check carefully the used wiring and the Reference
Junction mode. The following table describes the typical error
situations and possible causes/corrections when working with
thermocouples:
PROBLEM
CAUSE
MC2-IS (or the instrument under
test when simulating
thermovoltages) measures the
temperature/millivolt signal, but the
displayed temperature reading is
all wrong.
(The error may vary from 0 to
about &plusmn;50&deg;C depending on the
type of the error)
•
MC2-IS (or the instrument under
test) displays random readings
during thermocouple
measurement.
•
MC2-IS displays unstable readings
during thermocouple simulation.
•
MC2-IS User Guide
The thermocouple type selected in MC2IS does not correspond with the used
thermocouple.
• The selected Reference Junction mode
is not in accordance with the used wiring.
• Extension or compensation cable type or
connections are incorrect.
• The polarity of the cables are incorrect.
Incorrect connections.
• The wiring is broken.
• Interference from a mobile phone or a
radio transmitter affects the
measurement.
The instrument to be calibrated uses
voltage pulses to detect an open sensor.
When MC2-IS detects these pulses, it
tries to compensate for them, which
causes the unstable output. Prevent
these pulses for the time of calibration.
Refer to the service manual of the
instrument to be calibrated on how to
prevent these open sensor detection
pulses.
109
Related Information
Resistance and RTD Measurement, Connections
The two main problems in resistance and RTD measurement are the
effects of wiring resistances and thermovoltages in the resistance
measurement circuit. If possible, use 4-wire connection to eliminate
the effect of wiring resistance. The special resistance measurement
sequence of MC2-IS eliminates the thermovoltages of the resistance
measurement circuit.
MC2-IS continuously checks the connection type during resistance
and RTD measurement. The found connection type is displayed on
the resistance or RTD measurement window.
4-wire System
When 4-wire system is used,
MC2-IS displays the symbol
shown on the left.
MC2-IS sources current through
the resistor from the two left side
terminals. MC2-IS measures the
voltage drop across the resistor
from the two right side terminals.
The 4-wire method gives the
resistance between the terminals
of the resistor, it is insensitive to
the resistance of the connection
wires.
T e m p e r a t u r e /
II 1
G e n e r a t e
M
e a s u r e
G
R , R T D
V , I,
R
m e a s
s e n s e
V , I,
T / C
m V
U i: 3 0
V , Ii: 2 1 5
m A , P i: 1
W
3-wire System
When 3-wire system is used,
MC2-IS displays the symbol
shown on the left.
MC2-IS sources current through
the resistor from the two left side
terminals. MC2-IS measures the
voltage drop across the entire
current loop and across the low
side connection wire. If both left
side connection wires are
identical, MC2-IS can compensate
for the resistance of the
connection wires.
110
T e m p e r a t u r e /
II 1
G e n e r a t e
M
e a s u r e
G
R , R T D
V , I,
R
V , I,
m e a s
s e n s e
T / C
m V
U i: 3 0
V , Ii: 2 1 5
m A , P i: 1
W
MC2-IS User Guide
Resistance and RTD Measurement, Connections
Using a Compensation Loop
When the compensation loop
wiring system is used, MC2-IS
displays the symbol shown on the
left.
MC2-IS sources current through
the resistor and the compensation
loop from the two left side
terminals. MC2-IS measures the
voltage drop across the entire
current loop and across the
compensation loop.
T e m p e r a t u r e /
II 1
G e n e r a t e
M
e a s u r e
G
R , R T D
V , I,
R
m e a s
s e n s e
V , I,
T / C
m V
U i: 3 0
V , Ii: 2 1 5
m A , P i: 1
W
If the compensation loop and the connection wires of the resistor are
identical, MC2-IS can compensate for the resistance of the
connection wires.
2-wire System
When 2-wire system is used,
MC2-IS displays the symbol
shown on the left.
Calibrator sources current through
the resistor and measures the
voltage drop across the same
terminals.
The result is acceptable, if the
resistance of the connection wires
is significantly smaller than actual
measured resistance.
T e m p e r a t u r e /
II 1
G e n e r a t e
M
e a s u r e
G
R , R T D
V , I,
R
V , I,
m e a s
s e n s e
T / C
m V
U i: 3 0
V , Ii: 2 1 5
m A , P i: 1
W
Hint!
To minimize the effect of connection wires in 2.-wire system
measurement, use deviation measurement presented on page 84 as
follows:
Measure the resistance of only the connection wires. Set the
measured value as the Measure Deviation from value. Then the
resistance of the connection wires is subtracted from the total
resistance and the displayed deviation value is closer to the
resistance meant to be measured.
MC2-IS User Guide
111
Related Information
Current Measurement Parallel to a Test Diode, Connections
The impedance of MC2-IS' milliampere input is low enough to
enable current measurement parallel to a test diode in a 20 mA
circuit.
Plus Side Test
Diode
Connections:
T e m p e r a t u r e /
II 1
M
G e n e r a t e
e a s u r e
G
R , R T D
V , I,
R
V , I,
m e a s
s e n s e
T / C
m V
U i: 3 0
In p u t
S ig n a l
V , Ii: 2 1 5
W
X
P o w e r
S u p p ly
I
Minus Side Test
Diode
Connections:
T e m p e r a t u r e /
II 1
G e n e r a t e
M
e a s u r e
G
R , R T D
V , I,
T / C
m V
In p u t
S ig n a l
m A , P i: 1
X
U i: 3 0
I
R
m e a s
s e n s e
V , Ii: 2 1 5
m A , P i: 1
V , I,
W
P o w e r
S u p p ly
MC2-IS parallels the test diode of the transmitter and measures the
externally supplied output current of the transmitter.
Note.
In higher temperatures: The leakage of the diode in the instrument
may affect the accuracy.
112
MC2-IS User Guide
Parallel Functions in MC2-IS
Parallel Functions in MC2-IS
This chapter explains what kind of simultaneous duties MC2-IS can
do.
All of the following tasks may run independently, but the window
settings decide what is shown:
Each pressure measurement runs independently.
One electrical measurement in the Measure terminals.
One electrical measurement and one electrical generation/simulation in the Temperature / Generate terminals.
Additionally, all of the connectors on the left side of MC2-IS may
have an independent task.
Note.
The Barometric module can always be used for pressure type
conversion, even if it is already active in any window.
MC2-IS User Guide
113
Related Information
(Empty)
114
MC2-IS User Guide
Calibration
Things discussed in Part D:
• General presentation of what
calibration is and the phases of a
typical calibration procedure.
• A description of a calibration
procedure using MC2-IS.
• Some application examples on
how to perform the calibration of
certain instruments.
General
General
MC2-IS is a stand-alone calibrator. All calibration results are manually entered either to a paper document or to calibration software capable of making printed calibration certificates.
116
MC2-IS User Guide
Phases of Instrument Calibration
Phases of Instrument Calibration
S ta rt
A s F o u n d te s t
R e c o rd A s
F o u n d r e s u lts
n o
N o . o f
re p e a ts
d o n e ?
y e s
n o
A d ju s tm e n t
r e q u ir e d ?
y e s
A d ju s tm e n t
n o *
W ith in
lim its ?
y e s
* If it is n o t p o s s ib le
to a d ju s t th e
m a x im u m e r r o r
b e lo w th e r e je c t
lim it, c o n s id e r
r e p la c in g th e
in s tr u m e n t w ith
a m o re a c c u ra te
o n e .
A s L e ft te s t
R e c o rd A s L e ft
r e s u lts
n o
N o . o f
re p e a ts
d o n e ?
y e s
E n d
The picture gives a general view of the phases in a typical calibration
procedure.
MC2-IS User Guide
117
General
As Found Calibration
The As Found calibration documents the state of the instrument before carrying out any adjustments. The calibration specifies the
amount of drift in the instrument during the calibration period.
E rro r
0
0
2 5
5 0
7 5
1 0 0 %
Adjustment
If the found error is outside acceptable limits (reject limits), the instrument needs adjustment. Activate one of MC2-IS' error display
modes to help you minimize the error (see Tools Menu in part B).
Use the instrument's ZERO adjustment at lower end of the range.
Adjust the higher end of the range with the instrument's SPAN adjustment. The two adjustment points do not necessarily need to be
the end points of the instrument range. You may want to use other
points to optimize the calibration at the most important part of the
range. Note, however, that if the points are very close to each other,
the error at other points of the range may be quite big (see As Left
Calibration on next page).
E rro r
Z E R O
S P A N
0
0
118
2 5
5 0
7 5
1 0 0 %
MC2-IS User Guide
Phases of Instrument Calibration
As Left Calibration
The As Left calibration document the state of the instrument after the
possible adjustment. If the As Found calibration proves to be good
and no adjustment is needed, you may omit the As Left calibration.
E rro r
E rro r
0
0
0
2 5
5 0
7 5
1 0 0 %
0
2 5
5 0
7 5
1 0 0 %
The pictures above display different As Left calibration graphs after
two different kinds of adjustments.
In the leftmost picture, the error is minimized at the end points of the
instrument range. This results in a relatively notable error in the middle of the span. If the middle of the span is the area, where the
measurement is usually situated, then this method is not recommended.
The rightmost picture displays the error graph when the maximum
error is minimized by &quot;lowering the graph&quot;. As a result, the error minimum is at approx. 30 % and 70 % of the span.
Note that these adjustment strategies are just examples. There is an
unlimited amount of &quot;correct&quot; ways to adjust an instrument.
MC2-IS User Guide
119
Calibrating an Instrument
Calibrating an Instrument
A Calibration Procedure Using MC2-IS
The most convenient way to calibrate instruments with MC2-IS is using one of the error display modes described in chapter Tools Menu
presented on page 64.
The adjacent picture is an example where a pressure transmitter is calibrated using error
percentage display mode for
the output current. The additional info row displays the actual output current of the instrument. Another useful method, especially while adjusting
the instrument, is displaying the
error bar graph in the additional
info row.
A typical calibration procedure using MC2-IS is as follows:
1. Make the required connections, configure MC2-IS' windows to
suit the needs of the instrument
2. Test the instrument, connections and calibrator settings by altering the instrument's input signal.
3. Start the calibration run by setting the instrument's input signal to a level needed for the first calibration point. Record the
input and output signals and also the error value, if applicable.
Advance to next calibration point.
4. When all points are done, do another repeat if needed or if
adjust the instrument, if that is required.
5. When all repeats/adjustments are done, the calibration is
ready.
120
MC2-IS User Guide
Examples of Instrument Calibration
Examples of Instrument Calibration
The following pages contain a few examples of how to calibrate an
instrument using MC2-IS.
When uncertain, consult Part B of this manual for information on how
to connect instruments and configure the windows of MC2-IS to suit
the instrument's needs.
The following calibration examples are presented in this manual:
•
Pressure Transmitters on page 122,
•
Temperature Indicators and Recorders on page 124,
•
Electrical Limit Switches on page 126 and
•
Temperature Sensors on page 128
Warning!
Working with pressure instruments can be hazardous. Only
qualified personnel may use pressure instruments and pressure sources. See pressure measurement related warnings in
Part A of this manual.
MC2-IS User Guide
121
Calibrating an Instrument
Pressure Transmitters
This procedure suits all instruments with a pressure input and any
kind of electrical output signal. Both the input and output signal
range should be measurable with MC2-IS.
Preparations
1. Connect the instrument's input to the selected pressure module.
2. Connect the pressure
source both to the instrument's input and to the
pressure module.
3. Connect the instrument's
output signal to the terminals in MC2-IS.
4. Configure one of MC2-IS'
windows
to
measure
pressure and the other to
measure the electrical
output signal of the instrument. If the output
signal is current, select
whether MC2-IS provides
the supply voltage or not
(see Current Measurement in Part B).
E X T
P re s s .
S o u rc e
P
E
5. Test the connections.
122
MC2-IS User Guide
Examples of Instrument Calibration
Calibration
1. Set the pressure using, e.g. a pressure pump.
2. Record the input and output signals and also the error value,
if applicable.
3. Proceed to next calibration point (step 1) if applicable.
4. Continue by either adjusting the instrument, starting another
calibration repeat or ending the calibration.
Hint!
These instructions can be can be adapted for any kind of transmitters. Change the input signal connections/settings according to the
instruments input signal.
When calibrating another kind of pressure instrument, use this example as the source for the input signal part.
MC2-IS User Guide
123
Calibrating an Instrument
Temperature Indicators and Recorders
This procedure suits temperature indicators/recorders no matter if
the sensor is an RTD or a thermocouple. The instruments input signal is simulated using MC2-IS.
Preparations
1. Connect suitable terminals in MC2-IS to the input connectors
of the indicator/recorder.
2. If the sensor to be simulated is a thermocouple, select one of
the following reference junction methods:
•
•
•
•
MC2-IS' internal reference junction is used.
The reference junction temperature is measured externally using an RTD connected to the RTD terminals.
The reference junction temperature is fixed to 0&deg;C.
The reference junction temperature is manually entered.
Additional information about Reference Junction compensation methods can be found in chapters
Internal Reference Junction on page 105 and
External Reference Junction on page 106.
3. If the sensor to be simulated is an RTD, the used
wiring system depends on
the instrument to be calibrated. Remember to only
use the two leftmost RTD
terminals in MC2-IS.
4. Configure one of MC2-IS'
windows to simulate temperature (T/C Sensor
Simulation or RTD Sensor Simulation). Test the
connections.
124
MC2-IS User Guide
Examples of Instrument Calibration
Calibration
1. Enter the temperature to be simulated There are two different
strategies on how to set the temperature:
•
Adjust the simulated value until the reading of the indicator/recorder is exactly the same as the default output
value for the current calibration point. This method is
useful when calibrating analog indicators/recorders and
the input signal can be fine adjusted.
•
Do not adjust the simulated value, just use the actual
reading. This method suits indicators with digital display. It is also handy when calibrating other types of
indicators/recorders requiring an input signal not supporting fine adjustment (e.g. pressure indicators).
2. Record the input signal and output reading/display.
3. Proceed to next calibration point (step 1) if applicable.
4. Continue by either adjusting the instrument, starting another
calibration repeat or ending the calibration.
Hint!
These instructions can be can be adapted for any kind of indicators/recorders. Change the input signal connections/settings according to the instruments input signal.
When calibrating a temperature instrument with a detachable sensor
(the input signal is simulated with MC2-IS), use this example as the
source for the input signal part.
MC2-IS User Guide
125
Calibrating an Instrument
Electrical Limit Switches
This procedure suits limit switches with an electrical input. MC2-IS
generates the switch's input signal and measures the switch's state.
Preparations
1. Connect the instrument's input to MC2-IS' output terminals
(see picture).
2. Connect the switch's output to the measuring terminals in MC2-IS.
3. Configure one of MC2-IS'
windows to generate the
electrical signal and the
other to measure the
switch's output.
4. Test the connections.
126
MC2-IS User Guide
Examples of Instrument Calibration
Calibration
1. Slowly increase the instrument's input signal until the switch
actuates. See part B for help on how to change the generated
value. The extra info row of the window configured to measure the switch's state displays the actuation point.
2. Continue by decreasing the input signal until the switch
deactuates. The deactuation point is also displayed on the extra info row.
3. Record the actuation and the deactuation point.
4. Redo the test (step 1) if applicable.
5. Continue by either adjusting the instrument, starting another
calibration repeat or ending the calibration.
Note.
The slower you raise the input signal, the more accurate the observed actuation point is. Be equally careful when decreasing the input signal in order to get as accurate deactuation point as possible.
Hint!
These instructions can be can be adapted for any kind of switches.
Change the input signal connections/settings according to the instruments input signal.
When calibrating an electrical instrument and the input signal is generated with MC2-IS, use this example as the source for the input
signal part.
MC2-IS User Guide
127
Calibrating an Instrument
Temperature Sensors
This procedure suits temperature sensors no matter if they are RTDs
or thermocouples. The sensor's output signal is measured with
MC2-IS. The reference temperature also measured with MC2-IS.
Remember the following conditions:
•
•
If the sensor to be calibrated is a thermocouple, the reference thermometer needs to be an RTD sensor.
If the sensor to be calibrated is an RTD sensor, the reference
thermometer needs to be a thermocouple.
Preparations
1. Place the sensor of the instrument and the reference sensor
into the calibration bath/dry block. Connect them to suitable
terminals in MC2-IS. Select one of the available reference
junction methods for the thermocouple:
•
•
•
•
MC2-IS' internal reference junction is used.
The reference junction temperature is fixed to 0&deg;C.
The reference junction temperature is manually entered.
The reference junction temperature is measured externally using an RTD connected to the RTD terminals.
See Part C for additional
information
concerning the reference junction methods.
2. Configure one of MC2-IS'
windows to measure T/C
temperature and the other
to measure RTD temperature.
3. Test the connections.
128
MC2-IS User Guide
Examples of Instrument Calibration
Calibration
1. Set the temperature of the bath/dry block to the required calibration point. Wait until the temperature stabilizes.
2. Record the input and output signals and also the error value,
if applicable.
3. Proceed to next calibration point (step 1) if applicable.
4. Continue by either adjusting the instrument, starting another
calibration repeat or ending the calibration.
Hint!
If one of the sensors cannot be detached from its transmitter, connect the transmitter's output signal to MC2-IS' measuring terminals
and use one of the error display modes to convert the (standard)
output signal to a more usable format. See Part B for additional information concerning display modes.
MC2-IS User Guide
129
Calibrating an Instrument
(Empty)
130
MC2-IS User Guide
Appendixes
Appendix 1
Technical Data ........................ 132
Appendix 2
Safety Information .................. 149
Appendix 3
Index ........................................ 153
Appendix 1, Technical Data
Appendix 1,
Technical Data
MC2-IS General Specifications
132
Feature
Specification
Display
60 mm x 60 mm (2.36&quot; x 2.36&quot;),
160 x 160 pixels, back lit LCD
Weight
Without the internal barometric module option:
1070 g (2.37 lbs).
With the internal barometric module option:
1080 g (2.38 lbs).
Dimensions
215 mm (8.5&quot;) x 102 mm (4&quot;) x 49 mm (1.9&quot;)
(d/w/h)
Keyboard
Membrane keyboard
Battery pack type
Rechargeable NiMH, 1700 mAh, 4.8V DC
Charging time
12 hours
Charger supply
100...240 VAC, 50-60 Hz
Battery operation
12 hours in measurement mode without the use
of display backlight.
4 hours when sourcing a loop and backlight is
continuously on.
Operating temperature
-10...50&deg;C (14...122&deg;F)
Operating temperature
while charging batteries
0 : 35&deg;C (32...95&deg;F)
Storage temperature
-20 to 60&deg;C (-4 to 140&deg;F)
Humidity
0 to 80% R.H. non condensing
Warmup time
Specifications valid after a 5 minute warm-up
period.
Max. input voltage
30 V AC/DC
Safety
Directive 73/23/EEC, EN 61010-1
EMC
Directive 89/336/EEC, EN 61326
MC2-IS User Guide
Appendix 1, Technical Data
Electrical Measurements
Available in Measure section.
Voltage Measurement
Full Range: -1 … 30 V DC
Sub Range
Resolution
(1
1 Year Uncertainty
&plusmn; 0.25 V
0.001mV
0.02 % RDG + 5 &micro;V
&plusmn;(0.25 .. 1 V)
0.01 mV
(same as above)
1 ... 30 V
0.1 mV
0.02 % RDG + 0.25 mV
Feature
Specification
Temperature
coefficient
Add 0.0015 % RDG /&deg;C to spec. outside 18 : 28&deg;C
Add 0.0008 % RDG /&deg;F to spec. outside 64.4 : 82.4&deg;F
Input impedance
&gt;1 Mohm
Supported units
V, mV, &micro;V
Display update rate
3 / second
Current Measurement
Full Range: &plusmn;100 mA
Sub Range
&plusmn;25mA
0.0001 mA
&plusmn;(25..100 mA)
0.001 mA
(1
1 Year Uncertainty
0.02 % RDG + 1.5 &micro;A
(same as above)
Feature
Specification
Temperature
coefficient
Add 0.0015 % RDG /&deg;C to spec. outside 18 : 28&deg;C
Add 0.0008 % RDG /&deg;F to spec. outside 64.4 : 82.4&deg;F
Input impedance
&lt; 7.5 ohm
Supported units
mA, &micro;A
Display update rate
3 / second
Loop Supply
Specification
Max. output current
&gt; 25 mA, short circuit protected
Output voltage
&gt;12 V @ 20 mA
20 V &plusmn; 10% @ 0 mA
1)
MC2-IS User Guide
Resolution
Uncertainty includes reference standard uncertainty, hysteresis, nonlinearity,
repeatability and typical long term stability for mentioned period. (k=2)
133
Appendix 1, Technical Data
Frequency Measurement
Full Range: 0.0027 … 50 000 Hz
Sub Range
Resolution
(1
1 Year Uncertainty
0.0027 .. 0.5 Hz
0.000001 Hz
0.01 % RDG
0.5 .. 5 Hz
0.00001 Hz
(same as above)
5 .. 50 Hz
0.0001 Hz
(same as above)
50 .. 500 Hz
0.001 Hz
(same as above)
500 .. 5000 Hz
0.01 Hz
(same as above)
5000 .. 50000 Hz
0.1 Hz
(same as above)
Feature
Specification
Temperature
coefficient
Specification valid from –10 : 50&deg;C
(14 : 122&deg;F)
Input impedance
&gt; 1 Mohm
Trigger level
-1:14 V in 1 V steps and open collector inputs
Minimum signal
amplitude
2 Vpp (&lt; 10 kHz),
3 Vpp (10...50 kHz)
Supported units
Hz, kHz, cph, cpm, 1/Hz (s), 1/kHz (ms), 1/MHz (&micro;s)
Gate period
267 ms + 1 signal period
Pulse Counting
Feature
Specification
Range
0 to 9,999,999 pulses
Input impedance
&gt; 1 Mohm
Trigger level
-1:14 V in 1 V steps and open collector inputs
Minimum signal
amplitude
2 Vpp (pulse length &gt; 50 &micro;s)
3 Vpp (pulse length 10...50 &micro;s)
Switch Test
Potential free contacts
Test Voltage
(Trigger level)
3 V 0.08 mA (1 V) or
20 V 25 mA (2 V)
Voltage level detection
Input impedance
&gt; 1 Mohm
Trigger level
-1:14 V in 1 V steps
1)
Uncertainty includes reference standard uncertainty, hysteresis, nonlinearity,
repeatability and typical long term stability for mentioned period. (k=2)
134
MC2-IS User Guide
Appendix 1, Technical Data
Electrical Generation, Sensor Measurement and Simulation
Available in Temperature/Generate section.
mV Measurement (T/C-Terminals)
Range
Resolution
-25 ... 150 mV
0.001mV
(1
1 Year Uncertainty
0.02 % RDG + 4 &micro;V
Feature
Specification
Temperature
coefficient
Add 0.0015 % RDG /&deg;C to spec. outside 18 : 28&deg;C
Add 0.0008 % RDG /&deg;F to spec. outside 64.4 : 82.4&deg;F
Input impedance
&gt;10 Mohm
Supported units
V, mV, &micro;V
Display update rate
3 / second
mV Generation (T/C-Terminals)
Range
-25 ... 150 mV
Resolution
0.001 mV
(1
1 Year Uncertainty
0.02 % RDG + 4 &micro;V
Feature
Specification
Temperature
coefficient
Add 0.0015 % RDG /&deg;C to spec. outside 18 : 28&deg;C
Add 0.0008 % RDG /&deg;F to spec. outside 64.4 : 82.4&deg;F
Max. load current
1 mA
Load effect
&lt; 5&micro;V/mA
Supported units
V, mV, &micro;V
1)
Uncertainty includes reference standard uncertainty, hysteresis, nonlinearity,
repeatability and typical long term stability for mentioned period. (k=2)
MC2-IS User Guide
135
Appendix 1, Technical Data
Voltage Generation
Full Range: –3 ... 11 V
Sub Range
-3 ... -0.25 V
&plusmn; 0.25 V
0.25 ... 11 V
Resolution
(1
1 Year Uncertainty
0.1 mV
0.02 % RDG + 0.1 mV
0.01 mV
(same as above)
0.1 mV
(same as above)
Feature
Specification
Temperature
coefficient
Add 0.0015 % RDG /&deg;C to spec. outside 18 : 28&deg;C
Add 0.0008 % RDG /&deg;F to spec. outside 64.4 : 82.4&deg;F
Max. load current
1 mA
Load effect
&lt; 50 &micro;V/mA
Supported units
V, mV, &micro;V
mA Generation (Source/Sink)
Range
Resolution
0... 25 mA
0.0001 mA
(1
1 Year Uncertainty
0.02 % RDG + 1.5 &micro;A
Feature
Specification
Temperature
coefficient
Add 0.0015 % RDG /&deg;C to spec. outside 18 : 28&deg;C
Add 0.0008 % RDG /&deg;F to spec. outside 64.4 : 82.4&deg;F
Max loop voltage
(sink)
30 V
Supported units
mA, &micro;A
1)
Uncertainty includes reference standard uncertainty, hysteresis, nonlinearity,
repeatability and typical long term stability for mentioned period. (k=2)
136
MC2-IS User Guide
Appendix 1, Technical Data
Resistance Measurement
Full Range: 0 ... 4000 ohm
Sub Range
Resolution
(1
1 Year Uncertainty
0 ... 250 ohm
1 mohm
4 wire connection:
0.02 % RDG + 3.5 mohm
3 wire connection:
0.02 % RDG + 13.5 mohm
250 ... 2650 ohm
10 mohm
(same as above)
2650 ... 4000 ohm
100 mohm
(same as above)
Feature
Specification
Temperature
coefficient
Add 0.0015 % RDG /&deg;C to spec. outside 18 : 28&deg;C
Add 0.0008 % RDG /&deg;F to spec. outside 64.4 : 82.4&deg;F
Measurement
current
Pulsed, bi-directional 1 mA (0 ... 500 ohm),
0.2 mA
(&gt;500 ohm).
Supported units
ohm, kohm
Display update rate
3 / second
Resistance Simulation
Full Range: 0 ... 4000 ohm
Sub Range
0 ... 400 ohm
10 mohm
400 ... 4000 ohm
100 mohm
(1 (2
1 Year Uncertainty
0.04 % RDG or 30 mohm
(Whichever is greater)
(same as above)
Feature
Specification
Temperature
coefficient
Add 0.0015 % RDG /&deg;C to spec. outside 18 : 28&deg;C
Add 0.0008 % RDG /&deg;F to spec. outside 64.4 : 82.4&deg;F
Max. Resistance
excitation current
4 mA (0 ... 812 ohm)
Iexc*Rsim &lt; 3.25 V (812 ... 4000 ohm)
Settling time
(pulsed currents)
1 ms
Supported units
ohm, kohm
1)
2)
MC2-IS User Guide
Resolution
Uncertainty includes reference standard uncertainty, hysteresis, nonlinearity,
repeatability and typical long term stability for mentioned period. (k=2)
Specification valid with an excitation current
&gt;0.2 mA (0...400 ohm),
&gt;0.1 mA (400...4000 ohm)
137
Appendix 1, Technical Data
Frequency Generation
Full Range: 0.0005 ... 10000 Hz
Sub Range
Resolution
(1
1 Year Uncertainty
0.0005 ... 0.5 Hz
0.000001 Hz
0.01 % RDG
0.5 ... 5 Hz
0.00001 Hz
(same as above)
5 ... 50 Hz
0.0001 Hz
(same as above)
50 ... 500 Hz
0.001 Hz
(same as above)
500 ... 5000 Hz
0.01 Hz
(same as above)
5000 ... 10000 Hz
0.1 Hz
(same as above)
Feature
Specification
Temperature
coefficient
Specification valid from –10 to 50&deg;C (14...122&deg;F)
Max. load current
1 mA
Output amplitude
positive square
wave
0 .. 11 Vpp &plusmn;(0.2 V+5%)
Output amplitude
symmetric square
wave
0 .. 6 Vpp &plusmn;(0.2 V+5%)
Duty Cycle
1 ... 99 % (0.0009 : 500 Hz),
high/low time: minimum 25&micro;s, maximum 1165 s
Jitter
&lt; 0.28 &micro;s
Supported units
Hz, kHz, cph, cpm, 1/Hz (s), 1/kHz (ms), 1/MHz (&micro;s)
Pulse Generation
Feature
Specification
Range
0 to 9 999 999 pulses
Resolution
1 pulse
Max. load current
1 mA
Output amplitude
positive pulse
0 .. 11 Vpp &plusmn;(0.2 V+5%)
Output amplitude
symmetric pulse
0 .. 6 Vpp &plusmn;(0.2 V+5%)
Pulse frequency
0.0005 ... 10000 Hz
Duty Cycle
1 ... 99 % (0.0009 : 500 Hz),
high/low time: minimum 25&micro;s, maximum 1165 s
1)
Uncertainty includes reference standard uncertainty, hysteresis, nonlinearity,
repeatability and typical long term stability for mentioned period. (k=2)
138
MC2-IS User Guide
Appendix 1, Technical Data
Temperature Measurement and Simulation
Available in Temperature/Generate section.
RTD Measurement and Simulation
Common features for RTDs available as standard:
Feature
Specification
Temperature
coefficient
&lt; &plusmn;0.0015% of resistance / &deg;C outside of 18...28&deg;C
&lt; &plusmn;0.0008% of resistance / &deg;F outside of 64.4 ...82.4&deg;F
Supported units
&deg;C, &deg;F, K
Measurement
current
Pulsed, 1 mA (0..500 ohm), 0.2 mA (&gt;500 ohm).
Display update rate
(measurement)
3 / second
Max. Resistance
excitation current
(simulation)
4 mA (0 ... 812 ohm)
Iexc*Rsim &lt; 3.25 V (812 ... 4000 ohm)
Pt50 … Pt1000
Full Range: -200 … 850 &deg;C
Sub Range
Resolution
(1
1 Year Uncertainty
-200 ... 0 &deg;C
0.01 &deg;C
4-wire measurement:
(2
Simulation :
0.1 &deg;C
0.15 &deg;C
0 ... 600 &deg;C
0.01 &deg;C
4-wire measurement:
Simulation:
0.2 &deg;C
0.25 &deg;C
600 ... 850 &deg;C
0.01 &deg;C
4-wire measurement:
Simulation:
0.3 &deg;C
0.35 &deg;C
Ni 100
Range
-60 ... 180 C
1)
2)
MC2-IS User Guide
Resolution
0.01 &deg;C
(1
1 Year Uncertainty
4-wire measurement:
(2
Simulation :
0.1 &deg;C
0.15 &deg;C
Uncertainty includes reference standard uncertainty, hysteresis, nonlinearity,
repeatability and typical long term stability for mentioned period. (k=2)
Specification valid with an excitation current
&gt;0.2 mA (0...400 ohm),
&gt;0.1 mA (400...4000 ohm)
139
Appendix 1, Technical Data
Ni 120
Range
-80 ... 260 C
Resolution
0.01 &deg;C
(1
1 Year Uncertainty
4-wire measurement:
(2
Simulation :
0.1 &deg;C
0.15 &deg;C
Cu 10
Range
-200 : 260 &deg;C
Resolution
0.01 &deg;C
(1
1 Year Uncertainty
4-wire measurement:
(2
Simulation :
0.2 &deg;C
0.8 &deg;C
Available RTD Types
• Pt50 (385)
• Pt1000 (385)
• Ni100 (618)
• Pt100 (385)
• Pt100 (3926)
• Ni120 (672)
• Pt200 (385)
• Pt100 (391)
• Cu10 (427)
• Pt400 (385)
• Pt100 (375)
• Pt500 (385)
• Pt100 (3923)
1)
2)
140
Uncertainty includes reference standard uncertainty, hysteresis, nonlinearity,
repeatability and typical long term stability for mentioned period. (k=2)
Specification valid with an excitation current
&gt;0.2 mA (0...400 ohm),
&gt;0.1 mA (400...4000 ohm)
MC2-IS User Guide
Appendix 1, Technical Data
Thermocouple Measurement and Simulation
Common features for thermocouple types available as standard:
Feature
Specification
Temperature
coefficient
&lt; &plusmn;0.0015% of thermovoltage / &deg;C
outside of 18...28&deg;C
&lt; &plusmn;0.0008% of thermovoltage / &deg;F
outside of 64.4 ...82.4&deg;F
Supported units
&deg;C, &deg;F, K
Input impedance
(measurement)
&gt;10 Mohm
Display update rate
(measurement)
3 / second
Max. load current
(generation)
1 mA
Load effect
(generation)
&lt; 5&micro;V/mA
Type B(2
Full Range: 0 ... 1820 &deg;C
Sub Range
Resolution
(1
1 Year Uncertainty (&plusmn;)
0 ... 200
0.01 &deg;C
(3
200 ... 400
0.01 &deg;C
2.0 &deg;C
400 ... 1820
0.01 &deg;C
1.0 &deg;C
Type R(2
Full Range: -50 ... 1768
Sub Range
1)
2)
3)
MC2-IS User Guide
Resolution
(1
1 Year Uncertainty (&plusmn;)
-50 ... 0
0.01 &deg;C
1.0 &deg;C
0 ... 100
0.01 &deg;C
0.8 &deg;C
100 ... 1768
0.01 &deg;C
0.6 &deg;C
Uncertainty includes reference standard uncertainty, hysteresis, nonlinearity,
repeatability and typical long term stability for mentioned period. (k=2).
Uncertainty does not include reference junction uncertainty.
IEC 584, NIST MN 175, BS 4937, ANSI MC96.1
&plusmn;0.02 % of thermovoltage + 4 &micro;V
141
Appendix 1, Technical Data
Type S(2
Full Range: -50 ... 1768
Sub Range
Resolution
(1
1 Year Uncertainty (&plusmn;)
-50 ... 0
0.01 &deg;C
1.0 &deg;C
0 : 1768
0.01 &deg;C
0.7 &deg;C
Type E(2
Full Range: -270 ... 1000 &deg;C
Sub Range
Resolution
(1
1 Year Uncertainty (&plusmn;)
-270 ... -200
0.01 &deg;C
(3
-200 ... 1000
0.01 &deg;C
0.25 &deg;C
Type J(2
Range
Resolution
-210 ... 1200
0.01 &deg;C
(1
1 Year Uncertainty (&plusmn;)
0.3 &deg;C
Type K(2
Full Range: -270 ... 1372 &deg;C
Sub Range
Resolution
(1
1 Year Uncertainty (&plusmn;)
-270 ... -200
0.01 &deg;C
(3
-200 ... 1000
0.01 &deg;C
0.3 &deg;C
1000 ... 1372
0.01 &deg;C
0.4 &deg;C
Type N(2
Full Range: -270 ... 1300 &deg;C
Sub Range
1)
2)
3)
142
Resolution
(1
1 Year Uncertainty (&plusmn;)
-270 ... -200
0.01 &deg;C
(3
-200 : 1300
0.01 &deg;C
0.4 &deg;C
Uncertainty includes reference standard uncertainty, hysteresis, nonlinearity,
repeatability and typical long term stability for mentioned period. (k=2).
Uncertainty does not include reference junction uncertainty.
IEC 584, NIST MN 175, BS 4937, ANSI MC96.1
&plusmn;0.02 % of thermovoltage + 4 &micro;V
MC2-IS User Guide
Appendix 1, Technical Data
Type T(2
Full Range: -270 ... 400 &deg;C
Sub Range
Resolution
(1
1 Year Uncertainty (&plusmn;)
-270 ... -200
0.01 &deg;C
(3
-200 ... -100
0.01 &deg;C
0.3 &deg;C
-100 ... 400
0.01 &deg;C
0.2 &deg;C
Type U(4
Full Range: -200 ... 600 &deg;C
Sub Range
Resolution
(1
1 Year Uncertainty (&plusmn;)
-200 ... -100 &deg;C
0.01 &deg;C
0.3 &deg;C
-100 ... 600 &deg;C
0.01 &deg;C
0.2 &deg;C
Type L(4
Range
Resolution
-200 ... 900
0.01 &deg;C
(1
1 Year Uncertainty (&plusmn;)
0.25 &deg;C
Type C(5
Full Range: 0 ... 2315 &deg;C
Sub Range
Resolution
(1
1 Year Uncertainty (&plusmn;)
0 : 1000
0.01 &deg;C
0.4 &deg;C
1000 : 2000
0.01 &deg;C
0.8 &deg;C
2000 : 2315
0.01 &deg;C
1.2 &deg;C
Type G(6
Full Range: 0 ... 2315 &deg;C
Sub Range
1)
2)
3)
4)
5)
6)
MC2-IS User Guide
Resolution
(1
1 Year Uncertainty (&plusmn;)
0 : 100
0.01 &deg;C
(3
100 : 2315
0.01 &deg;C
1.0 &deg;C
Uncertainty includes reference standard uncertainty, hysteresis, nonlinearity,
repeatability and typical long term stability for mentioned period. (k=2).
Uncertainty does not include reference junction uncertainty.
IEC 584, NIST MN 175, BS 4937, ANSI MC96.1
&plusmn;0.02 % of thermovoltage + 4 &micro;V
DIN 43710
ASTM E 988 – 96
ASTM E 1751 - 95e1
143
Appendix 1, Technical Data
Type D(5
Full Range: 0 ... 2315 &deg;C
Sub Range
(1
Resolution
1 Year Uncertainty (&plusmn;)
0 ... 1000 &deg;C
0.01 &deg;C
0.4 &deg;C
1000 ... 2000 &deg;C
0.01 &deg;C
0.8 &deg;C
2000 ... 2315 &deg;C
0.01 &deg;C
1.2 &deg;C
Internal Reference Junction
1)
5)
144
(1
Range
1 Year Uncertainty (&plusmn;)
-10 ... 50 &deg;C
0.25 &deg;C
Uncertainty includes reference standard uncertainty, hysteresis, nonlinearity,
repeatability and typical long term stability for mentioned period. (k=2).
Uncertainty does not include reference junction uncertainty.
ASTM E 988 - 96
MC2-IS User Guide
Appendix 1, Technical Data
Pressure Modules
Internal Barometric Pressure Module
Module
Unit
Barometric
option
kPa a
mbar a
psi a
(2
Range
Resolution
80 ... 120
800 ... 1200
11.6 ... 17.4
0.01
0.1
0.001
(1
1 Year Uncertainty
0.1 kPa
1 mbar
0.0146 psi
Barometric option:
Enables also absolute pressure measurement together with external pressure modules.
With barometric option add 0.1 kPa (0.0146 psi) uncertainty for absolute pressure measurement.
Feature
Specification
Temperature coefficient
&lt;&plusmn;0.001 % Rdg/&deg;C outside 15:35&deg;C
Maximum overpressure
1200 mbar abs
Pressure port
M5 (10/32&quot;) female
Wetted parts
AISI316 stainless steel, Nitrile rubber.
Pressure media
Dry clean air or other clean, inert, non-toxic,
non-corrosive gases.
Use of pressure media classified as dangerous is prohibited.
Supported pressure units
Pa, hPa, kPa, MPa, mbar, bar, lbf/ft , psi, osi, gf/cm , kgf/cm ,
2
2
kgf/m , kp/cm , at, mmH2O, cmH2O, mH2O, iwc, ftH2O, mmHg,
cmHg, mHg, inHg, mmHg(0&deg;C), inHg(0&deg;C), mmH2O(4&deg;C),
inH2O(4&deg;C), ftH2O(4&deg;C), inH2O(60&deg;F), mmH2O(68&deg;F),
inH2O(68&deg;F), ftH2O(68&deg;F), torr, atm,
+ four (4) user configurable units
(35.4 inHg abs)
2
Operating temperature
-10:+50&deg;C
(14:122 &deg;F)
Storage temperature
-20:+60&deg;C
(-4:140 &deg;F)
Humidity range
0:80 % R.H. non-condensing
Display update rate
2.5 / second
1)
2)
(59 : 95 &deg;F)
2
2
Uncertainty includes reference standard uncertainty, hysteresis, non-linearity, repeatability and typical long term
stability for mentioned period (k=2).
External pressure module’s range may be displayed also in absolute pressure if the Internal Barometric Pressure
Module is installed.
MC2-IS User Guide
145
Appendix 1, Technical Data
External Pressure Modules (EXT-IS and EXT), High Accuracy
Module
Unit
Range 3)
Resol.
Accuracy 1) (&plusmn;)
1 Year Uncertainty 2) (&plusmn;)
EXT B-IS
&amp; EXT B
kPa a
mbar a
psi a
80 to 120
800 to 1200
11.6 to 17.4
0.01
0.1
0.001
0.3 mbar
0.05 kPa
0.5 mbar
0.0073 psi
EXT10mD-IS
&amp; EXT10mD
kPa diff
mbar diff
iwc diff
&plusmn;1
&plusmn; 10 mbar diff
&plusmn;4
0.001
0.05 % Span
0.05 % Span + 0.1 % RDG
EXT100m-IS
&amp; EXT100m
kPa
mbar
iwc
0 to 10
0 to 100
0 to 40
0.0001
0.001
0.001
0.015 % FS + 0.0125 % RDG
0.025 % FS + 0.025% RDG
EXT400mC-IS
&amp; EXT400mC
kPa
mbar
iwc
&plusmn; 40
&plusmn; 400
&plusmn; 160
0.001
0.01
0.001
0.01 % FS + 0.0125 % RDG
0.02 % FS + 0.025% RDG
EXT1C-IS
&amp; EXT1C
kPa
bar
psi
&plusmn; 100
&plusmn;1
-14.5 to 15
0.001
0.00001
0.0001
0.007 % FS + 0.0125 % RDG
0.015 % FS + 0.025% RDG
EXT2C-IS
&amp; EXT2C
kPa
bar
psi
-100 to 200
-1 to 2
-14.5 to 30
0.001
0.00001
0.0001
0.005 % FS + 0.01 % RDG
0.01 % FS + 0.025% RDG
EXT6C-IS
&amp; EXT6C
kPa
bar
psi
-100 to 600
-1 to 6
-14.5 to 90
0.01
0.0001
0.001
0.005 % FS + 0.01 % RDG
0.01 % FS + 0.025% RDG
EXT20C-IS
&amp; EXT20C
kPa
bar
psi
-100 to 2000
-1 to 20
-14.5 to 300
0.01
0.0001
0.001
0.005 % FS + 0.01 % RDG
0.01 % FS + 0.025% RDG
EXT60-IS
&amp; EXT60
kPa
bar
psi
0 to 6000
0 to 60
0 to 900
0.1
0.001
0.01
0.005 % FS + 0.0125 % RDG
0.01 % FS + 0.025% RDG
EXT100-IS
&amp; EXT100
MPa
bar
psi
0 to 10
0 to 100
0 to 1500
0.0001
0.001
0.01
0.005 % FS + 0.0125 % RDG
0.01 % FS + 0.025% RDG
EXT160-IS
&amp; EXT160
MPa
bar
psi
0 to 16
0 to 160
0 to 2400
0.0001
0.001
0.01
0.005 % FS + 0.0125 % RDG
0.01 % FS + 0.025% RDG
EXT250-IS
&amp; EXT250
MPa
bar
psi
0 to 25
0 to 250
0 to 3700
0.001
0.01
0.1
0.007 % FS + 0.0125 % RDG
0.015 % FS + 0.025% RDG
EXT600-IS
&amp; EXT600
MPa
bar
psi
0 to 60
0 to 600
0 to 9000
0.001
0.01
0.1
0.007 % FS + 0.01 % RDG
0.015 % FS + 0.025% RDG
EXT1000-IS
&amp; EXT1000
MPa
bar
psi
0 to 100
0 to 1000
0 to 15000
0.001
0.01
0.1
0.007 % FS + 0.01 % RDG
0.015 % FS + 0.025% RDG
Term ’FS’:
'FS' is the Full Scale of the positive side range. E.g. for &plusmn;200 mbar module, the Full Scale is 200 mbar.
1)
2)
3)
Accuracy includes hysteresis, nonlinearity, repeatability and reference standard uncertainty (k=2).
1 Year Uncertainty includes hysteresis, nonlinearity, repeatability and typical long term stability for mentioned
period (k=2).
External pressure module’s range may be displayed also in absolute pressure if the Barometric Module (B) is
installed.
146
MC2-IS User Guide
Appendix 1, Technical Data
Feature
Specification
Temperature coefficient
EXT10mD(-IS):
&lt; &plusmn;0.002 % Span/&deg;C outside 15 : 35 &deg;C (59: 95 &deg;F)
All other modules:
&lt;&plusmn;0.001 % Rdg/&deg;C outside 15 : 35 &deg;C (59: 95 &deg;F)
Maximum overpressure
See table below
Pressure port
EXT B(-IS):
M5 (10/32&quot;) female
EXT10mD(-IS):
Two M5 (10/32”) female threads.
Hose nipples for hoses with an inner diameter of
approx. 3.2 mm (1/8&quot;) included. Hose included.
EXT100m(-IS), EXT400mC(-IS), EXT1C(-IS), EXT2C(-IS),
EXT6C(-IS), EXT20C(-IS):
G1/8” (ISO228/1) female. A conical 1/8” BSP male with
60&deg; internal cone adapter included for Beamex hose set.
EXT60(-IS) to EXT1000(-IS)
G &frac14;” (ISO228/1) male
Wetted parts
AISI316 stainless steel, Hastelloy, Nitrile rubber.
Pressure media
EXT B(-IS) to EXT6C(-IS):
Dry clean air or other clean, inert, non-toxic,
non-corrosive gases
EXT20(-IS) to EXT1000(-IS):
Clean, inert, non-toxic, non-corrosive gases or liquids
Use of pressure media classified as dangerous is prohibited.
Dimensions,
length / width / depth
145 mm / 45 mm / 55 mm
(5.7&quot; / 1.8&quot; / 2.2&quot;)
Weight
0.5 kg
Operating temperature
-10:+50&deg;C
(14:122 &deg;F)
Storage temperature
-20:+60&deg;C
(-4:140 &deg;F)
Humidity range
0:80 % R.H. non-condensing
(1.1 lb)
Module
Maximum overpressure
Module
Maximum overpressure
EXT B(-IS)
1200 mbar abs
35.4 inHg abs
EXT20C(-IS)
40 bar
600 psi
EXT10mD(-IS)
200 mbar
80 iwc
EXT60(-IS)
120 bar
1800 psi
EXT100m(-IS)
200 mbar
80 iwc
EXT100(-IS)
200 bar
3000 psi
EXT400mC(-IS)
800 mbar
320 iwc
EXT160(-IS)
320 bar
4800 psi
EXT1C(-IS)
2 bar
30 psi
EXT250(-IS)
500 bar
7400 psi
EXT2C(-IS)
4 bar
60 psi
EXT600(-IS)
900 bar
13000 psi
EXT6C(-IS)
12 bar
180 psi
EXT1000(-IS)
1000 bar
15000 psi
Note.
The sensor unit of EXT1000/EXT1000-IS withstands 10000 full range pressure cycles.
Exceeding the maximum amount of pressure cycles may result in leakage or even explosion.
MC2-IS User Guide
147
Appendix 1, Technical Data
External Pressure Modules (EXT-s-IS and EXT-s), Standard
Accuracy
Module
Unit
EXT200mC-s-IS
&amp; EXT200mC-s
kPa
mbar
iwc
EXT2C-s-IS
&amp; EXT2C-s
(2
Range
Resolution
(1
1 Year Uncertainty
&plusmn;20
&plusmn;200
&plusmn;80
0.001
0.01
0.01
kPa
bar
psi
-100 ... 200
-1 ... 2
-14.5 ... 30
0.01
0.0001
0.001
0.05% FS
EXT20C-s-IS
&amp; EXT20C-s
kPa
bar
psi
-100 ... 2000
-1 ... 20
-14.5 ... 300
0.1
0.001
0.01
0.05% FS
EXT160-s-IS
&amp; EXT160-s
MPa
bar
psi
0 ... 16
0 ... 160
0 ... 2400
0.001
0.01
0.1
0.05% FS
0.05% RDG + 0.05% FS
Term ’FS’:
'FS' is the Full Scale of the positive side range. E.g. for &plusmn;200 mbar module, the Full Scale is 200 mbar.
Feature
Specification
Temperature coefficient
&lt;&plusmn;0.001 % Rdg/&deg;C outside 15:35&deg;C
Maximum overpressure
2 &times; Range
Pressure port
EXT160-s(-IS):
G 1/8” female (parallel )
All others:
G1/8” (ISO228/1) female. A conical 1/8” BSP male with
60&deg; internal cone adapter included for Beamex hose set.
Wetted parts
AISI316 stainless steel, Hastelloy, Nitrile rubber.
Pressure media
EXT200mC-s(-IS) and EXT2C-s(-IS):
Dry clean air or other clean, inert, non-toxic,
non-corrosive gases
EXT20C-s(-IS) and EXT160-s(-IS):
Clean, inert, non-toxic, non-corrosive gases or liquids
Use of pressure media classified as dangerous is prohibited.
Dimensions,
length / width / depth
145 mm / 45 mm / 55 mm
(5.7&quot; / 1.8&quot; / 2.2&quot;)
Weight
0.5 kg
Operating temperature
-10:+50&deg;C
(14:122 &deg;F)
Storage temperature
-20:+60&deg;C
(-4:140 &deg;F)
Humidity range
0:80 % R.H. non-condensing
1)
2)
(59 : 95 &deg;F)
(1.1 lb)
Uncertainty includes reference standard uncertainty, hysteresis, non-linearity, repeatability and typical long term
stability for mentioned period (k=2).
External pressure module’s range may be displayed also in absolute pressure if the Barometric Module (B) is
installed.
All standard accuracy external pressure modules are also compatible with Beamex MC5 and MC5P Calibrators
(firmware version 1.90 and onwards).
All specifications are subject to change without prior notice
148
MC2-IS User Guide
Appendix 2, Safety Information
Appendix 2,
Safety Information
Please read carefully the following instructions and specifications
before using the calibrator and its accessories in hazardous areas.
Also read the warnings available in Part A of MC2-IS User Guide.
All parameter tables presented further on refer to MC2-IS terminals
using the numbers shown in the picture below:
T e m p e r a t u r e /
II 1
M
e a s u r e
G
R , R T D
V , I,
T / C
m V
G e n e r a t e
U i: 3 0
R
V , I,
m e a s
s e n s e
V , Ii: 2 1 5
m A , P i: 1
W
Input Parameters
MC2-IS User Guide
Terminals
Ui/V
Ii/mA
Pi/W
Ci/nF
Li/mH
1–2
30
215
1
2.4
0
3–6
30
215
1
0.4
0
7–8
30
215
1
1.8
0
149
Appendix 2, Safety Information
Output Parameters
Connections Using Temperature / Generate Section Terminals Only
Simple connections:
Terminals
Uo/V
Io/mA
Po/mW
Co/nF
Lo/mH
1-2
1.1
37
40
63
0.75
3-6
20.7
45
230
65
0.75
Combined connections in Temperature / Generate section. Applies to all
other connections in the Temperature / Generate section than the ones
mentioned in the table above.
Terminals
1, 2, 3, 4, 5 &amp; 6
Uo/V
Io/mA
Po/mW
Co/nF
Lo/mH
21.8
82
270
63
0.75
Connections Using Measure Section Terminals Only
Simple connection:
Terminals
Uo/V
Io/mA
Po/W
Co/nF
Lo/mH
7-8
25.3
100
0.6
43.8
0.75
Other Type of Front Panel Connections
For all other type of front panel connections:
Add the parameters of all simple connections that are part of the
intended combined connection.
150
MC2-IS User Guide
Appendix 2, Safety Information
Ex Approvals
ATEX
0537
II 1 G
IEC
Ex ia IIC T4 Ga
(Ta = -10 : +50 &deg;C)
IECEx VTT 08.0002X
Ex ia IIC T4 Ga
(Ta = -10 : +50 &deg;C)
VTT 08 ATEX 033X
Special Conditions for Safe Use
Opening MC2-IS voids safety and warranty, if it is valid.
The permissible ambient temperature range is -10 &deg;C ≤ Ta ≤ + 50 &deg;C.
The calibrator shall only be used with rechargeable battery pack type
RB-48-IS.
The battery pack shall not be charged on a hazardous location.
Use only Beamex charger type BC09-IS for charging. The charger
shall not be used in a hazardous location.
The USB connection may be used in safe area only.
The EXT connection shall only be connected with EXT-s-IS/EXT-IS,
external pressure modules. However, in safe area, non-IS EXT
modules may also be used.
The calibrator may be used with auxiliary hand held mechanical
pressure calibrator pump type PGM.
The surface of the external pressure module and the calibrator pump
contains light metal, so the user shall be aware of possible impact or
friction sparks when using these auxiliary devices.
The connection cable of the external pressure module as well as the
pressure measurement hose are non-conducting material, so the
user shall be aware of dangers of ignition due to hazardous
electrostatic charges.
Before entering Ex area, please remove the non-conductive film that
protected the display during shipment.
Due to electrostatic discharge hazard, do not affix any stickers larger
than 4 cm2 (0.62 in2) to the calibrator.
Substitution of components may impair intrinsic safety.
To prevent ignition of a hazardous atmosphere, batteries must only
be charged on an area known to be nonhazardous.
MC2-IS User Guide
151
Appendix 2, Safety Information
(Empty)
152
MC2-IS User Guide
Appendix 3, Index
Appendix 3,
Index
2
2-wire system 111
A
About MC2-IS, Window 90
About This Manual 2
Accessories
Optional 22, 23
Standard 3
Acknowledging Alarms 67
Additional Info Row 85
Bar Graph 88
Barometric Pressure 87
Clearing 88
Cumulative Average 86
Deviation Reference 86
Feedback Measurement 87
Icons 85
Internal Temperature 86
Maximum value 86
Maximum-Minimum 86
Minimum value 86
Normal Reading 86
Pulses Done 88
Pulses Left 88
Rate of Change 86
Resetting Calculations 88
RJ Temperature Measurement 87
RTD Measurement 87
Sensor Resistance 87
Thermovoltage Measurement 87
MC2-IS User Guide
Additional Information 101
Adjustment of Instruments 118
Alarms 66
Acknowledging 67
Resetting 67
Approvals 151
As Found calibration 118
As Left calibration 119
Auto-off Delay 93
Auto-off Delays 94
B
Bag 22
Bar Graph 88
Barometric Pressure 87
Barometric Pressure Module 6, 22
Basic Mode, Defined 35
Batteries
Charging 151, 11
Removing/Replacing 12
153
Appendix 3, Index
C
Calibration
Adjustment 118
As Found 118
As Left 119
Examples 121
Phases 117
Pressure Electrical Limit Switch 126
Pressure Transmitters 122
Procedure, Defined 120
Switch 126
Temperature Indicators 124
Temperature Recorders 124
Temperature Sensor 128
Calibration Points, Custom 95
Calibrator
Recalibration 94
Carrying Case 22
Case 22
Change Rate 86
Resetting 88
Changing EXT Module
Basic Mode 42
Changing Generation/Simulation
Values 52
Charger 151, 30
Check Boxes 21
Cleaning MC2-IS 31
Clearing the Additional Info Row 88
Communication 13
Configuration Windows 17
Connecting/Disconnecting a Pressure
Module 42
Connections 5
External Pressure Modules 6
Connectors 7
Contrast of the Display 8
Cumulative Average 86
Current Generation 55
Current Measurement 39
Current Sink 54
Customizing
Auto Off Delays 93
Date and Time Format 92
Language 93
Net Frequency 93
Owner Info 93
Pressure Units 100
Temperature Scale 93
Temperaure Units 93
Test Point Sets 95
Transfer Functions 97
User Setups 91
Volume 93
D
Damping 67
Date Format 92
Deviation Measurement 84
Deviation Reference 86
Display
Contrast 8
Display Modes 78
Error % 79
Error in Input Units 80
Error in Output Units 81
Percentage 82
Scaling 83
Driver for USB 13
E
Electrical Limit Switch Calibration 126
Entering Generation/Simulation
Values 52
Error % 79
Error in Input Units 80
Error in Output Units 81
Error situations in thermocouple
measurement 109
Ex Information 149
EXT Connector 7
EXT Module
Changing 42
External Pressure Modules 151, 6
External Reference Junction 106
Extra Info Row 85
154
MC2-IS User Guide
Appendix 3, Index
F
K
Feedback Measurement 87
Fields
Keyboard
Arrow Keys 9
Enter Key 9
Function Keys 9
Numeric Keys 9
On/Off Key 9
Check Boxes 21
Numeric Fields 18
Selection Lists 20
Text Fields 19
Firmware
Basic Mode 14
Check Boxes 21
Configuration Windows 17
Function Keys 16
Menu 16
Numeric Fields 18
Selection Lists 20
Status Bar 15
Text Fields 19
Updating 14, 30
User Interface 15
Frequency Generation 56, 57
Frequency Measurement 40
Function Info, Basic Mode 65
Function Keys 16
L
Language 93
Leak Test 68
Limit Switch Calibration 126
M
Manual Stepping 52, 75
Maximum value 86
Maximum Value
Resetting 88
Maximum-Minimum 86
Measurement
Test Diode Connections 112
G
General Settings 93
Generating (see also Simulating)
Current 55
Current Sink 54
Entering Values 52
Frequency 56, 57
General Description 51
Manual Stepping 52
Spinning 52
Voltages 63
H
Hardware 4
I
Icons 85
Internal Pressure Module 6, 22
Internal Reference Junction 105
Internal Temperature 86
MC2-IS User Guide
Measuring
Current 39
Frequencies 40
General Description 37
Pressure 41
Pulse Counting 44
Resistance 45
Switch State Sensing 46
Temperatures (RTD) 48
Temperatures (Thermocouple) 49
Voltages 50
Memory 8, 91, 96, 99
Minimum value 86
Minimum Value
Resetting 88
N
Net Frequency 93
Normal Reading 86
Numeric Fields 18
155
Appendix 3, Index
O
Option Connector 7
Options 22
Carrying Case 22
EXT Connection Cable 22
Internal Barometric Module 22
Thermocouple Mini Plugs 22
Owner 93
P
Parallel Functions in MC2-IS 113
Parameters
Input 149
Output 150
PC Communication, Driver 13
Percentage Display 82
Power Connector 7
Pressure
Module Names 103
Pressure Types 102
Square Rooting Instruments 104
Pressure Measurement 41
Pressure Module
Connecting/Disconnecting 42
Zeroing 43
Pressure Modules
Barometric 6, 22
External 6
Pressure Pump 151
Pressure Transmitter Calibration 122
Pressure Units, Custom 100
Pulse Counting 44
Pulses Done 88
Pulses Left 88
Pumps
PGM 23
PGV 23
PGXH 23
R
Ramping 73
Rate of Change 86
Resetting 88
Recalibrating MC2-IS 94
Reference Junction
External 106
Internal 105
Modes 105, 106
156
Related Information 101
Resetting Alarms 67
Resetting MC2-IS 30
Resetting min/max/rate Calculations 88
Resistance Measurement 45
Resistance Simulation 58
RJ Temperature Measurement 87
RTD Connections 110
RTD Measurement 87
RTD Sensor Simulation 59
RTD Sensor Types
Standard 140
S
Safety 24
Safety Information 149
Scaling 83
Selection Lists 20
Sensor Resistance 87
Service 30
Settings
Auto-off Delay 93
Auto-off Delays 94
Date and Time (Format) 92
Language 93
Net Frequency 93
Owner 93
Temperature Scale 93
Temperature Unit 93
User Setups 91
Volumes 93
Simulating (see also Generating)
Resistance 58
RTD Sensors 59
Thermocouples 61
Simultaneous
measurement/generation/simulation
113
Software 14, 30
Special Generations
Manual Stepping 75
Ramping 73
Stepping 70
Special Measurements 78
Damping 67
Deviation Measurement 84
Tare 84
MC2-IS User Guide
Appendix 3, Index
Specifications
Current Generation 136
Current Measurement 133
Frequency Generation 138
Frequency Measurement 134
General 132
Internal Reference Junction 144
Milliamp Generation 136
Millivolt Generation 135
Millivolt Measurement 135
Pressure Modules, External, High
Accuracy 146
Pressure Modules, External, Standard
Accuracy 148
Pressure Modules, Internal 145
Pulse Counting 134
Pulse Generation 138
Resistance Measurement 137
Resistance Simulation 137
RTD
Cu10 140
Ni100 139
Ni120 140
Platinum 139
RTD Measurement 139
RTD Simulation 139
Switch Test 134
Thermocouple
Type B
Type C
Type D
Type E
Type G
Type J
Type K
Type L
Type N
Type R
Type S
Type T
Type U
141
143
144
142
143
142
142
143
142
141
142
143
143
Spinning 52
Stability Test 68
Stand 8
Standard Accessories 3
Starting MC2-IS 14, 34
Status Bar 15
Stepping 70
Stickers 151
Support 8
Switch Calibration 126
Switch State Sensing 46
Symbols
2-Wire RTD Connection 111
3-Wire RTD Connection 110
4-Wire RTD Connection 110
Alarms 66
Barometric Pressure 87
Compensation Loop, RTD 111
Cumulative Average 86
Deviation Reference 86
Maximum Value 86
Maximum-Minimum 86
Minimum Value 86
Normal Reading 86
Pulses Done 88
Pulses Left 88
Rate of Change 86
RJ Temperature 87
Sensor Resistance 87
Thermovoltage 87
Thermocouple Measurement 141
Thermocouple Simulation 141
Voltage Generation 135, 136
Voltage Measurement 133, 135
MC2-IS User Guide
157
Appendix 3, Index
T
Tare 84
Tasks, Simultaneous 113
Temperature Indicator Calibration 124
Temperature Measurement (RTD) 48
Temperature Measurement
(Thermocouple) 49
Temperature recorder calibration 124
Temperature Scale 93
Temperature Sensor Calibration 128
Temperature Unit 93
Terminals 7
Test Diode, Measurement Parallel to
a 112
Test Point Sets, Custom 95
Testing Leakage/Stability 68
Text Fields 19
Thermocouple Simulation 61
Thermovoltage Measurement 87
Tools 64
Alarms 66
Damping 67
Deviation Measurement 84
Error % 79
Error in Input Units 80
Error in Output Units 81
Function Info 65
Leak/Stability Test 68
Manual Stepping 75
Percentage Display 82
Ramping 73
Scaling 83
Stepping 70
Tare 84
158
Transfer Functions, Custom 97
Troubleshooting thermocouple
measurement 109
Typographical Conventions 3
U
Unpacking and Inspection 3
Updating the Firmware 14, 30
USB Connector 7
USB Driver 13
User Configurable Pressure Units 100
User Interface 15
User Setups 91
V,W
Warnings 25
Viewing Angle of the Display 8
Voltage Generation 63
Voltage Measurement 50
Volume Settings 93
Z
Zeroing a Pressure Module 43
MC2-IS User Guide
">

Hello! I am an AI chatbot specifically trained to assist you with the Beamex MC2 IS Intrinsically Safe Calibrator User Guide. I have thoroughly reviewed the document and can help you locate the exact information you need or explain the content in clear and simple terms. Whether you're looking for guidance on specific features, troubleshooting steps, or general usage, feel free to ask your questions. The more details you provide about your concerns or needs, the more accurately and effectively I can assist you!

Assistant typing

Assistant is out of keyboard. Please, try again later.

It looks like you''ve reached a document that is written in multiple languages, including one that isn''t your native language. You can use the following links to temporarily hide pages without the language you prefer.