Ford Galaxy, S-MAX Vehicle Quick Reference Guide

FORD GALAXY / S-MAX
Quick Reference Guide
About This Quick Reference Guide
We have created this guide to help you get to know certain
features of your vehicle quickly. It only contains basic
instructions to get you started and is not a substitute for the
Owner's Manual.
You must read the full instructions in the Owner's Manual
along with all the warnings. The more that you know about
your vehicle, the greater the safety and pleasure you will get
from driving it.
Thank you for choosing Ford.
WARNING
Always drive with due care and attention when using and operating the controls and features on
your vehicle.
Note: This guide describes product features and options available throughout the range, sometimes even
before they are generally available. It may describe options not fitted to your vehicle.
Note: Some of the illustrations in this guide may be used for different models, so may appear different to
your vehicle. However, the essential information in the illustrations is always correct.
Note: Always use and operate your vehicle in line with all applicable laws and regulations.
The information contained in this publication was correct at the time of going to print. In the interest of
continuous development, we reserve the right to change specifications, design or equipment at any time
without notice or obligation. No part of this publication may be reproduced, transmitted, stored in a
retrieval system or translated into any language in any form by any means without our written permission.
Errors and omissions excepted.
© Ford Motor Company 2014
All rights reserved.
Part Number: CG3561en 10/2012 20140708081506
AT A GLANCE
1
Galaxy/S-MAX (CA1) Vehicles Built From: 20-08-2012, Vehicles Built Up To: 18-12-2014, CG3561en enGBR, Edition date: 10/2012, Second Printing
A
Lighting controls.
B
Air vents.
C
Direction indicators. Telephone control buttons. Voice control buttons. Lane
departure warning control buttons.
D
Audio controls.
E
Instrument cluster.
F
Information display controls.
G
Wiper lever.
H
Audio or navigation unit.
I
Start-stop switch.
J
Parking aid switch.
K
Hazard warning flasher switch.
L
Passenger airbag deactivation warning lamp.
M
Storage compartment.
N
Heated windscreen and heated rear window switches.
O
Climate controls.
P
Cigar lighter.
Q
Start Button.
R
Ignition switch.
S
Cruise control and speed limiter switches. Adaptive cruise control (ACC) switches.
Speed limiter switches.
T
Steering wheel adjustment lever.
U
Driver Knee airbag.
V
Horn.
W
Cruise control and speed limiter switches. Adaptive cruise control (ACC) switches.
Speed limiter switches.
FASTENING THE SEAT BELTS
Second row centre seat belt
Note: The seat belt tongues are designed
so that you can only insert them into the
correct buckle.
2
Galaxy/S-MAX (CA1) Vehicles Built From: 20-08-2012, Vehicles Built Up To: 18-12-2014, CG3561en enGBR, Edition date: 10/2012, Second Printing
Locking Your Vehicle
The retractor for the rear centre seat belt
is located in the roof.
To fasten the seat belt:
1.
Pull the belt out steadily. It may lock if
you pull it sharply or if the vehicle is on
a slope.
2. Insert the smaller tongue into the black
buckle to the right of the centre seat.
3. Pull the larger tongue across the lap and
insert it into the buckle to the left of the
centre seat.
Locking buttons are located on each of the
front doors and the liftgate.
KEYLESS ENTRY
Press a locking button once.
Unlocking Your Vehicle
Passive locking and unlocking requires a
valid passive key to be located within one
of the three external detection ranges.
These are located approximately 5 ft
(1.5 m) from the front door handles and the
liftgate.
Note: The keyless entry system may not
function if the passive key is close to metal
objects or electronic devices such as mobile
phones.
3
Galaxy/S-MAX (CA1) Vehicles Built From: 20-08-2012, Vehicles Built Up To: 18-12-2014, CG3561en enGBR, Edition date: 10/2012, Second Printing
To use global opening, press and hold the
unlock button after you have unlocked your
vehicle. To use global closing, press and
hold the lock button after you have locked
your vehicle. Release the button once the
power windows start to move.
Note: When you use global opening or
closing, you can press the unlock or lock
button again to stop the power windows.
AUTOWIPERS
Pull one of the door handles or press the
button to open the liftgate.
Note: A valid passive key must be located
within the detection range of that door.
Locking and Unlocking the Doors
with the Key Blade
A
High sensitivity
B
On
C
Low sensitivity
The rain sensor will continuously measure
the amount of water on the windscreen and
adjust the speed of the front wipers
automatically.
Adjust the sensitivity of the rain sensor
using the rotary control.
1. Carefully remove the cover.
2. Remove the key blade and insert it into
the lock.
GLOBAL OPENING AND
CLOSING
You can open or close all of the power
windows for a short time after you have
unlocked or locked your vehicle with the
remote control.
4
Galaxy/S-MAX (CA1) Vehicles Built From: 20-08-2012, Vehicles Built Up To: 18-12-2014, CG3561en enGBR, Edition date: 10/2012, Second Printing
Wind noise
CHANGING THE WIPER BLADES
You may hear a rumbling noise when just
one of the windows are open. Lower the
opposite window slightly to reduce this
noise.
Windscreen wiper blades
ELECTRIC EXTERIOR MIRRORS
A
Left-hand mirror
B
Off
C
Right-hand mirror
Mirror tilting positions
Switch off the ignition and move the wiper
lever to position A within three seconds.
Release the lever when the windscreen
wipers have moved to the service position.
POWER WINDOWS
Resetting the memory of the
electric windows
Reverse mirror dipping
After the battery has been disconnected
from the vehicle you must reset the memory
separately for each window:
Depending on the switch position (A or C),
the relevant exterior mirror will dip
whenever you select reverse gear, giving
you a view of the kerb.
1.
Lift the switch until the window is fully
closed. Hold the switch lifted for one
more second.
2. Release the switch and lift it again, two
or three times, for one more second.
3. Open the window and try to close it
automatically.
4. Reset and repeat procedure if the
window does not close automatically.
Note: You can disable this feature by leaving
the switch in position B.
The exterior mirror will return to the original
position:
• If the vehicle speed exceeds 10 km/h (6
mph).
• Approximately 10 seconds after reverse
gear has been disengaged.
• If the switch is returned to position B.
5
Galaxy/S-MAX (CA1) Vehicles Built From: 20-08-2012, Vehicles Built Up To: 18-12-2014, CG3561en enGBR, Edition date: 10/2012, Second Printing
False Alerts
BLIND SPOT INFORMATION
SYSTEM
There may be instances when the system
will alert you and there is no vehicle present
in the blind spot zones. For example; road
guardrails or motorway concrete walls.
Blind Spot Information System
(BLIS)
The system is a convenience feature that
assists you to detect vehicles that may have
entered your blind spot zones (A). The
detection area is on both sides of your
vehicle extending rearward from the
exterior mirrors to approximately 10 ft (3 m)
beyond the rear of your vehicle. The system
will alert you if certain vehicles enter your
blind spot zones while driving.
Turning the System On and Off
You can turn the system on and off using
the information display.
INFORMATION DISPLAYS
You can access the menu using the
Information and entertainment display
control.
Controls
Press the up and down arrow buttons to
scroll through and highlight the options
within a menu.
Using the System
Press the right arrow button to enter a
sub-menu.
The system displays a yellow indicator
located in the exterior mirrors.
Press the left arrow button to exit a menu.
Hold the left arrow button pressed at any
time to return to the main menu display
(escape button).
Press the OK button to choose and confirm
a setting.
Device list
The icon changes to show the current
function in use.
Detection Limitations
CD
There may be instances where vehicles
entering and exiting the blind spot zones
may not be detected.
Radio
Auxiliary input
6
Galaxy/S-MAX (CA1) Vehicles Built From: 20-08-2012, Vehicles Built Up To: 18-12-2014, CG3561en enGBR, Edition date: 10/2012, Second Printing
Phone
AUTOMATIC CLIMATE
CONTROL
Settings
Your vehicle is fitted with either a dual-zone
or triple-zone system. When the system is
in mono mode, all the temperature zones
are linked to the driver's zone. When you
switch mono mode off, the dual-zone
system allows you to set different
temperatures for the driver's and
passenger's zone. On vehicles fitted with a
triple-zone system, you can set a third
temperature for the rear passenger's zone.
TRIP COMPUTER
Distance to empty
Indicates the approximate distance the
vehicle will travel on the fuel remaining in
the tank. Changes in driving pattern may
cause the value to vary.
INFORMATION MESSAGES
Press the OK button to acknowledge and
remove some messages from the
information display. Other messages will
be removed automatically after a short
time.
A
MONO mode on and off
B
Windscreen defrosting and
demisting
C
Recirculated air
D
Air conditioning on and off
E
AUTO mode on and off
Certain messages need to be confirmed
before you can access the menus.
Message indicator
You can set the temperature between 16°C
(61°F) and 28°C (82°F) in steps of 0.5°C
(1°F).
The message indicator illuminates to
supplement some messages. It will be red
or amber depending on the severity of the
message and will remain on until the cause
of the message has been rectified.
Recommended setting: AUTO, 22°C (72°F).
Some messages will be supplemented by
a system specific symbol with a message
indicator.
7
Galaxy/S-MAX (CA1) Vehicles Built From: 20-08-2012, Vehicles Built Up To: 18-12-2014, CG3561en enGBR, Edition date: 10/2012, Second Printing
AUXILIARY HEATER
REAR SEATS
Parking heater
Second Row Seats
Note: The parking heater will only operate
if there is at least 7.5 litres (1.6 gallons) of
fuel in the fuel tank and the ambient
temperature is below 15°C (59°F). The
heater will not operate if the battery is low.
Folding the Seatbacks Down
You can switch the system on and off using
the information display.
Remote starting
Starting
Hold the transmitter with the antenna
upwards and press the ON button for at
least two seconds.
HEAD RESTRAINTS
Note: Third row seat head restraints have
restricted height adjustment.
1. Lower the head restraints.
2. Slide the seats backward as far as they
will go.
3. Insert the centre seat belt into the
retainer in the roof.
4. On the outboard seats, pull the lever
and fold the seatback into a sloped
position. Pull the lever again and fold
down the seatback.
8
Galaxy/S-MAX (CA1) Vehicles Built From: 20-08-2012, Vehicles Built Up To: 18-12-2014, CG3561en enGBR, Edition date: 10/2012, Second Printing
5. On the centre seat, pull the loop
between the seat cushion and the
seatback and fold down the seatback.
6. To engage the seatbacks in the folded
position, pull the lever or loop again and
push the seatback firmly down until it
latches into position.
To return the seat to the seating position,
pull the lever or loop and fold the seatback
up until it engages.
Third Row Seats
Folding the Seats Flat
3. To return the seat to the seating
position. Fold the carpeted cover back,
grasp the grip (B) and pull the seatback
upward and then rearward.
4. Fold the seat cushion back and lock in
to position.
SUN SHADES
Sun blind relearning
1.
If the blind no longer opens or closes using
the one-touch feature, follow the relearning
procedure in the Owner's Manual.
Pull loop A at the rear of the seat
cushion.
MEMORY FUNCTION
2. The seat cushion will automatically turn
over and lie flat on the floor (1). The
seatback will automatically fold down.
A
Seat adjustment controls
B
Memory pre-set buttons
9
Galaxy/S-MAX (CA1) Vehicles Built From: 20-08-2012, Vehicles Built Up To: 18-12-2014, CG3561en enGBR, Edition date: 10/2012, Second Printing
Resetting the memory
Up to four different driver's seat and
exterior mirror positions can be stored in
the memory. Your preferred setting for the
reverse mirror dipping feature can also be
stored.
If any seat position travel is interrupted (e.g.
an obstacle in the way or loss of power
supply), you will need to reset the memory.
Note: Make sure all electrical accessories
are switched off.
Setting a memory pre-set
1. Turn the ignition to position II.
2. Operate the seat adjustment control to
move the seat in the required direction
until it stops. A click will be heard.
3. Release the seat adjustment control
and immediately press and hold the
switch in the same direction for at least
3 seconds. Keep it held until the seat
stops at the mechanical end of its travel
and a click is heard.
4. Release the seat adjustment control.
5. Operate the same seat adjustment
control in the opposite direction for at
least 3 seconds. Keep it held until the
seat stops at the mechanical end of its
travel and a click is heard.
Passive setting
The vehicle stores the seating and mirror
positions for up to four remote controls or
passive keys. Next time the vehicle is
unlocked, the position of the seat and
mirrors will adjust to the last used position.
Each time you turn the ignition off, the
current seat and mirror settings are stored
on the remote control or passive key used.
Active setting
1. Turn the ignition on.
2. Adjust the seat and exterior mirrors to
the desired position.
3. Press and hold the desired pre-set
button B until a single chime sounds to
confirm.
KEYLESS STARTING
Recalling a stored seat position
Ignition On
Note: To stop seat movement during a
recall, press any driver seat adjustment
control, any of the memory buttons or any
mirror control switch. Seat movement will
also stop if you move the vehicle.
Passive recall
Note: If more than one passive key is in
range, the memory function will move to the
settings of the first key stored.
When you unlock the vehicle with the
remote control or pull the driver door handle
with a passive key in range, the seat and
mirrors will move to the position stored on
that remote control or passive key.
Press the button once without your foot on
the brake or clutch pedal.
Note: The keyless starting system may not
function if the passive key is close to metal
objects or electronic devices such as mobile
phones.
Active recall
Press the pre-set button associated with
the desired driving position. The seat and
mirrors will move to the position stored on
that pre-set.
Starting with Manual Transmission
1. Fully depress the clutch pedal.
2. Press the start button.
10
Galaxy/S-MAX (CA1) Vehicles Built From: 20-08-2012, Vehicles Built Up To: 18-12-2014, CG3561en enGBR, Edition date: 10/2012, Second Printing
Note: Releasing the clutch pedal during
engine start will stop the engine cranking and
return to ignition on.
•
•
•
•
•
Starting with Automatic
Transmission
1. Make sure the transmission is in P or N.
2. Fully depress the brake pedal.
3. Press the start button.
Note: Releasing the brake pedal during
engine start will stop the engine cranking and
return to ignition on.
The outside temperature is too low or
too high.
The driver's door has been opened.
Low engine operating temperature.
Low brake system vacuum.
If a road speed of 5 km/h (3 mph) has
not been exceeded.
To re-start the engine
Note: The gear lever must be in the neutral
position.
Depress the clutch pedal.
Stopping the Engine When the
Vehicle is Moving
The system may automatically restart the
engine under certain conditions, for
example:
Press and hold the start button for two
seconds or press twice within two seconds.
•
•
Low battery voltage.
To maintain the interior climate.
DIESEL PARTICULATE FILTER
ECO MODE
During regeneration at low speed or engine
idle, you may smell a hot metallic odour
and could notice a clicking metallic sound.
This is due to the high temperatures
reached during regeneration and is normal.
The system assists the driver to drive more
efficiently by constantly monitoring
characteristics of gear changing,
anticipation of traffic conditions and speeds
on motorways and open roads.
USING START-STOP
Type 1
Note: The system is on by default. To switch
the system off, press the switch in the
instrument panel. The system will only be
de-activated for the current ignition cycle.
To turn it on, press the switch again.
To stop the engine
1. Stop the vehicle.
2. Move the gear lever to the neutral
position.
3. Release the clutch pedal.
4. Release the accelerator pedal.
Gear shifting
B
Anticipation
C
Efficient speed
Type 2 and 3
The relevant information will be shown in
the display.
Gear shifting
The system may not shut down the engine
under certain conditions, for example:
•
•
A
Using the highest drivable gear appropriate
for the road conditions will improve fuel
consumption.
To maintain the interior climate.
Low battery voltage.
11
Galaxy/S-MAX (CA1) Vehicles Built From: 20-08-2012, Vehicles Built Up To: 18-12-2014, CG3561en enGBR, Edition date: 10/2012, Second Printing
Anticipation
FUEL FILLER FLAP
Adjusting your vehicle speed and the
distance to other vehicles without the need
for heavy braking or acceleration will
improve fuel consumption.
Efficient speed
Higher speeds use more fuel. Reducing your
cruising speed on open roads will improve
fuel consumption.
USING ECO MODE
The system is accessed using the relevant
information display menu. See
Information Displays (page 6).
1.
Press the flap to open it.
Resetting Eco mode
Reset the average fuel consumption.
Note: New values may take a short time to
calculate.
FUEL CONSUMPTION
The following will help to improve fuel
consumption.
2. Open the flap fully until it engages.
Tyre Pressures
Check your tyre pressures regularly.
Gear Shifting
Use the highest gear appropriate for the
road conditions.
Anticipation
Adjust your vehicle speed and the distance
to other vehicles without the need for heavy
braking or acceleration.
Efficient Speed
Higher speeds use more fuel. Reduce your
cruising speed on open roads.
12
Galaxy/S-MAX (CA1) Vehicles Built From: 20-08-2012, Vehicles Built Up To: 18-12-2014, CG3561en enGBR, Edition date: 10/2012, Second Printing
3. Insert the fuel nozzle up to and including
the first notch on the nozzle A. Keep it
resting on the cover of the fuel pipe
opening.
Note: On vehicles with manual transmission,
if the gear lever is in neutral when you release
the clutch pedal and depress the accelerator
pedal, the EPB will be released
automatically.
Note: The clutch pedal must be fully
depressed before the DAR will operate.
Engage first or reverse gear, move off as
normal using the accelerator and clutch
pedals and the EPB will be automatically
released.
PARKING AID
4. Slightly raise the fuel nozzle to remove
it.
Switching the parking aid on and
off
ELECTRIC PARKING BRAKE
Note: The parking aid switches off
automatically when you start the engine or
when you exceed 16 km/h (10 mph).
The electric parking brake (EPB) replaces
the conventional handbrake. It is operated
by a switch located in the centre console.
Note: The front and rear sensors are always
activated or deactivated together.
Manual release
The parking aid is per default off. To switch
the parking aid on, press the switch in the
instrument panel or select reverse gear.
Note: To release the EPB, the ignition must
be in position II.
The light in the switch illuminates when the
parking aid is activated.
To turn it off, press the switch again.
USING CRUISE CONTROL
Switching Cruise Control On and
Off
Hold the brake pedal depressed and press
down the switch.
Automatic release - Drive away
release (DAR)
Note: On vehicles with automatic
transmission, the driver's door must be
closed and the driver's seatbelt must be
fastened before the DAR will operate.
13
Galaxy/S-MAX (CA1) Vehicles Built From: 20-08-2012, Vehicles Built Up To: 18-12-2014, CG3561en enGBR, Edition date: 10/2012, Second Printing
Setting a Speed
If the system detects that you are becoming
drowsy or there is a deterioration in your
driving, the system will alert you.
Press the SET+ switch or the SET- switch
to store and maintain your current speed.
The cruise control indicator will illuminate.
USING DRIVER ALERT
Changing the Set Speed
Switching the system on and off
Press the SET+ switch to accelerate or the
SET- switch to decelerate.
Activate the system using the information
display.
Cancelling the Set Speed
System display
Press the brake pedal or press the CAN
switch.
When active the system will run
automatically in the background and only
issue warnings if required. You can view the
status at any time using the information
display.
Resuming the Set Speed
Press the RES switch to resume the speed
that you previously set.
The alertness level is shown by six steps as
a coloured bar.
USING THE SPEED LIMITER
Press button A to switch the system on and
off.
The status bar will travel from left to right
as the calculated alertness level decreases.
•
•
•
Green - No rest required.
Yellow - First (temporary) warning.
Red - Second warning.
Setting the speed limit
LANE DEPARTURE WARNING
Use the cruise control switches to alter the
maximum speed setting.
The system will automatically detect and
track the lane markings on the road. If it
detects that the vehicle is unintentionally
drifting towards the lane boundaries then
a visual warning will be displayed in the
information display. There is also a warning
given in the form of a vibration felt through
the steering wheel.
Press the SET+ switch or the SET- switch
to select your desired speed limit.
Press button B to cancel the limiter and
place it in standby mode.
Press the RES button to resume the limiter.
DRIVER ALERT
The system automatically monitors your
driving behaviour using various inputs
including the front camera sensor.
14
Galaxy/S-MAX (CA1) Vehicles Built From: 20-08-2012, Vehicles Built Up To: 18-12-2014, CG3561en enGBR, Edition date: 10/2012, Second Printing
USING LANE DEPARTURE
WARNING
BLUETOOTH SETUP
Before you can use your mobile phone, it
must be bonded to your vehicle's telephone
system.
Switching the System On and Off
The following are required before a
Bluetooth connection can be made.
1.
A
System on
B
System off
The Bluetooth features must be
activated on your mobile phone and the
audio unit. Make sure the Bluetooth
menu option in the audio unit is set to
ON.
Note: For information on the Bluetooth
settings for your mobile phone, refer to the
manufacturer’s instructions.
2. In the Bluetooth menu on your mobile
phone, search for Ford Audio and
select it.
3. Enter the code number shown on the
vehicle display using your mobile phone
keypad. If no code number is shown on
the display, enter the Bluetooth PIN
number 0000 using the mobile phone
keypad. Now enter the Bluetooth PIN
number shown on the vehicle display.
Turn the system on and off using the switch
on the indicator stalk.
4. If your mobile phone asks you to
authorize the automatic connection,
select YES.
A column of lane markings is displayed
either side of the vehicle graphic.
For further information on how to use your
mobile phone through your vehicle's
telephone system, refer to your Owner's
Manual.
The lane markings are colour coded as
follows:
•
•
•
Green - The system is ready to warn you
of any unintentional lane departure.
Red - Your vehicle is approaching or is
too close to the detected lane
boundary. Take immediate safe action
to reposition your vehicle.
Grey - The relevant lane boundary will
be suppressed.
CONNECTING AN EXTERNAL
DEVICE
External devices may be connected using
the auxiliary input socket and the USB port.
You can find the socket in the centre
console.
If the lane markings turn red or a vibration
is felt through the steering wheel, you must
take immediate and safe action to align
your vehicle and correct any unintended
lane drift.
Select the auxiliary input via the CD/AUX
button and playback will be heard through
the vehicle speakers.
15
Galaxy/S-MAX (CA1) Vehicles Built From: 20-08-2012, Vehicles Built Up To: 18-12-2014, CG3561en enGBR, Edition date: 10/2012, Second Printing
">