Y1878 Fiberoptic Illuminator

1 GENERAL SYSTEM DESCRIPTION

The Y1878 300-Watt Xenon light source described herein is specifically designed for use as an illumination source for fiber optic illumination applications. As a result, the system shall have the following general features:

1.1.1 4 port flush mount design turret for fiber optic light cable connection to fit ACMI, Storz, Wolf, Olympus industry standard fibers

1.1.2 Simple lamp module replacement with no tools required

1.1.3 Simple power “ON” switch separate from the lamp ignition switch

1.1.4 Standard lamp safety features

1.1.5 Low noise generation

1.1.6 Very high brightness light output.

1.1.7 Even output beam profile

1.1.8 Compact footprint

1.1.9 Quick re-strike in the event that the device shuts down from overheating

1.1.10 Single world-wide universal power supply

2 INTENDED USAGE

2.1 General

This 300 W Xenon light source shall be used as an illumination source to provide light to fiber optic cables or light guides.

Atlas Specialty Lighting assumes no responsibility for suitability for any particular application of the lightsource or any consequential damages associated with the use of

the lightsource.

2.2 Personnel

2.2.1 Any trained personnel that has familiarized themselves with the product by reading the operation manual provided

2.3 Sterilization/Disinfection

2.3.1 The light source may be wiped-down with hospital approved disinfectants (e.g. 10% clorox/90% water solution) applied with a damp cloth.

3 ASSOCIATED EQUIPMENT

3.1 Fiber optic light guides (cables) not provided by Atlas Specialty Lighting

Issue x 2

17 January 2006

Y1878

CERMAX 300Watt Xenon Fiber Optic Illumiator for Atlas Specialty Lighting

Specification

1 Electrical Input

1.1

1.2

AC Power Connector Located on rear panel, dual fuses

1.3

2 Performance, Features & Warranty

2.1

Input Voltage 100 - 240 VAC, 50/60Hz universal, 6.0A input

Line cord IEC320, 6', US and Europe options

Light Output - 2000 Lumens nominal initial output through 6mm glass rod at full rated power

- Spectral output 380 - 750nm nominal

2.2

- < 8% instability p-p through 6mm glass rod @ 0-100Hz

- Beam profile to have "smooth" distribution with no shadows or sharp peaks

Overtemperature Prorection Automatic shut down in the event of overheating

Comments

All light output specifications refer to "system only" performance. Light output via optical fibers or other optical components may vary.

Fans operate when AC power is on and are independent of lamp status.

2.3

2.4

Over Heat Recovery / Auto Cool Unit to become fully operational within approximately 3 minutes after thermal shut down

& all obstructions to air flow removed at environmental temperature of < 22C (72F)

Fans will remain on in the event of thermal shut down when power is ON.

Lamp must be switched on by using lamp ON / OFF switch located on front panel

Fiber Optic Connection Safety Feature - Lamp will not ignite unless a fiber optic cable is fully inserted into the active port on the turret

Fans will remain on in the absence of a fiber optic cable inserted into active port when power is ON

- Lamp power is cut or blocked if fiber optic cable is removed from active port to prevent accidental light leakage

Lamp Power Supply PS300 type

2.5 Lamp Module Y1879 "low profile" CERMAX 300 Watt lamp module, incorporating proprietary type lamp

2.6

Lamp Module Replacement By easy access to lamp module via latched hinged door. No tools required.

Lamp specifications may vary slightly from standard PE300C-10F

Lamp replacement door "interlocked" for safety. Lamp power will be cut when door is open

2.7

Lamp Life - 500 hours to 50% of initial output specification measured through 6mm glass rod

- > 1000 hours typical measured through 6mm glass rod

System Warranty 12 months exlcuding lamp 2.8

3 User Interface / Control

3.1

3.2

3.3

3.4

User Instructions Operation manual to be included with every lightsource

Standby Switch Located on front panel, illuminated when ON

Lamp ON / OFF Switch Located on front panel. Lamp ON status indicated by LED on front panel. Illuminated when lamp is ON.

Fiber Optic Adapter - 4 port turret with WOLF, STORZ, ACMI, OLYMPUS ports

Lamp ignition not automatic with standby switch ON

When lamp ON button is depressed to turn lamp on, the "lamp on LED" flashes until such time as the lamp ignites. If the lamp fails to ignite in approximately 4 seconds (possible fault condition) the system will time out and the lamp ON button will need to be depressed again to initiate lamp ignition.

Turret rotated to select one fiber port for illumination at a time. Turret rotation will be resitant enough to prevent non-deliberate rotation by pulling fiber cables

3.5

Light Attenuation Shutter - Controlled by membrane buttons on front panel.

- 2 Buttons for relative intensity increments (up and down)

- 1 button for shutter fully closed

- 1 button for shutter fully open

- Relative level of illumination indicated by a digital numeric display (blue numerals)

3.6

Lamp Hour Counter - Lamp hour mode is selected while "Lamp Hours" button located on front panel is depressed.

- While lamp hour mode is selcted the number of elapsed lamp hours will be displayed on the relative brightness display.

- Elapsed lamp hours will be displayed up to 999 hours.

- Elapsed lamp hours displayed can be reset by end user

Lamp hour counter also records number of time the lamp hours have been reset. This number is displayed when lamp hours are re-set.

4 Mechanical & Environmental

4.1

4.2

4.3

4.4

4.5

Dimensions Height 5.0" x Width 16.9" x Depth 13.8" (nominal)

Weight 20lbs (9kg) nominal

Exterior finish Atlas Specialty Lighting art work and colors

Touch Temperature Per UL2601-1

Sterilization The light source may be wiped-down with hospital approved disinfectants (e.g. 10% clorox/90% water solution) applied with a damp cloth (must not be wet)

Designed for modular expansion

4.6

4.7

4.8

4.9

4.11

4.12

Operating & Storage Humidity 10 - 85% relative humidity, non-condensing

4.13

5 Regulatory Approvals

5.1

Operating Temperature 6C to 40C

Storage Temperature -20C to + 85C

Operating Pressure 1 Atmosphere nominal

Audible Noise < 45dB

Shipping, Shock & Vibration per ISTA 1A

Cooling Vents to direct airflow toward the back of the unit

Compliance to standards -IEC 60601-1:1998+A1:1991+A2:1995+A1.3:1997

-UL 60601-1:2003

-EN 60601-1:1990+A1:1993+A2:1995+A13:1997

-EN 60601-1-2:2001

-CAN / CSA C22.2 No. 601.1/M90(R1997),B/98,S1-94

5.2

Regulatory Markings - UL mark

- CUL mark

- CE mark

6

Atlas Specialty Lighting assumes no responsibility for the suitability of this lightsource for any particular application or any consequential damages associated with the use of this lightsource

Issue x 2

17 January 2006