1/2” HAMMER DRILL

Model

68169

SET UP AND OPERATING INSTRUCTIONS

Visit our website at: http://www.harborfreight.com

Read this material before using this product.

Failure to do so can result in serious injury.

SAVE THIS MANUAL.

Copyright

©

2010 by Harbor Freight Tools

®

Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual product may differ slightly from the product described herein. Tools required for assembly and service may not be included.

. All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of

For technical questions or replacement parts, please call 1-800-444-3353.

SAVE THIS MANUAL

Keep this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the back of the manual near the assembly diagram (or month and year of purchase if product has no number). Keep this manual and the receipt in a safe and dry place for future reference.

IMPORTANT SAFETY

INFORMATION

In this manual, on the labeling, and all other information provided with this product:

This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.

DANGER indicates a hazardous situation which, if not avoided, will result in death or serious injury.

WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury.

CAUTION, used with the safety alert symbol, indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.

NOTICE is used to address practices not related to personal injury.

CAUTION, without the safety alert symbol, is used to address practices not related to personal injury.

General Power Tool Safety Warnings

WARNING Read all safety warnings

and instructions. Failure to follow

the warnings and instructions may result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

The term ″power tool″ in the warnings refers to your mains-operated (corded) power tool or battery-operated

(cordless) power tool.

1.

Work area safety

a.

Keep work area clean and well lit.

Cluttered or dark areas invite accidents.

b.

Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids,

gases or dust. Power tools create

sparks which may ignite the dust or fumes.

c.

Keep children and bystanders away while operating a power

tool. Distractions can cause you to

lose control.

2.

Electrical safety

a.

Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter

plugs with grounded power tools.

Unmodified plugs and matching outlets will reduce risk of electric shock.

b.

Avoid body contact with grounded surfaces such as pipes, radiators,

Page 2

For technical questions, please call 1-800-444-3353.

SKU 68169

ranges and refrigerators. There is an

increased risk of electric shock if your body is grounded.

c.

Do not expose power tools to rain

or wet conditions. Water entering

a power tool will increase the risk of electric shock.

d.

Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp

edges or moving parts. Damaged

or entangled cords increase the risk of electric shock.

e.

When operating a power tool outdoors, use an extension cord

suitable for outdoor use. Use of a

cord suitable for outdoor use reduces the risk of electric shock.

f.

If operating a power tool in a damp location is unavoidable, use a

Ground Fault Circuit Interrupter

(GFCI) protected supply. Use of a

GFCI reduces the risk of electric shock.

3.

Personal safety

a.

Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol

or medication. A moment of inattention

while operating power tools may result in serious personal injury.

b.

Use personal protective equipment.

Always wear eye protection. Safety

equipment such as dust mask, nonskid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.

c.

Prevent unintentional starting.

Ensure the switch is in the offposition before connecting to power source and/or battery pack, picking

up or carrying the tool. Carrying

power tools with your finger on the switch or energizing power tools that have the switch on invites accidents.

d.

Remove any adjusting key or wrench

before turning the power tool on.

A wrench or a key left attached to a

rotating part of the power tool may result in personal injury.

e.

Do not overreach. Keep proper

footing and balance at all times. This

enables better control of the power tool in unexpected situations.

f.

Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing and gloves away

from moving parts. Loose clothes,

jewelry or long hair can be caught in moving parts.

g.

If devices are provided for the connection of dust extraction and collection facilities, ensure these

are connected and properly used.

Use of these devices can reduce dustrelated hazards.

h.

Only use safety equipment that has been approved by an appropriate

standards agency. Unapproved

safety equipment may not provide adequate protection. Eye protection must be ANSI-approved and breathing protection must be NIOSH-approved for the specific hazards in the work area.

4.

Power tool use and care

a.

Do not force the power tool. Use the correct power tool for your

application. The correct power tool will

do the job better and safer at the rate for which it was designed.

b.

Do not use the power tool if the

switch does not turn it on and off.

Any power tool that cannot be controlled

SKU 68169

For technical questions, please call 1-800-444-3353.

Page 3

with the switch is dangerous and must be repaired.

c.

Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing

accessories, or storing power tools.

Such preventive safety measures reduce the risk of starting the power tool accidentally.

d.

Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions

to operate the power tool. Power

tools are dangerous in the hands of untrained users.

e.

Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before

use. Many accidents are caused by

poorly maintained power tools.

f. Keep cutting tools sharp and clean.

Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.

g.

Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and

the work to be performed. Use of

the power tool for operations different from those intended could result in a hazardous situation.

5.

Service

a.

Have your power tool serviced by a qualified repair person using only

identical replacement parts. This will

ensure that the safety of the power tool is maintained.

Drill and Impact Drill Safety

Warnings

1.

Wear ear protectors with impact

drills. Exposure to noise can cause

hearing loss.

2.

Use Auxiliary Handle (4) supplied

with the Drill. Loss of control can cause

personal injury.

3.

Hold power tools by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or its own

cord. Contact with a ″live″ wire will make

exposed metal parts of the tool ″live″ and shock the operator.

4. Maintain labels and nameplates on the tool. These carry important safety information. If unreadable or missing, contact Harbor Freight Tools for a replacement.

5. Avoid unintentional starting. Prepare to begin work before turning on the tool.

6. Do not lay the tool down until it has come to a complete stop. Moving parts can grab the surface and pull the tool out of your control.

7. When using a handheld power tool, maintain a firm grip on the tool with both hands to resist starting torque.

8. Do not leave the tool unattended when it is plugged into an electrical outlet.

Turn off the tool, and unplug it from its electrical outlet before leaving.

9. This product is not a toy. Keep it out of reach of children.

10. People with pacemakers should consult their physician(s) before use.

Electromagnetic fields in close proximity to heart pacemaker could cause

Page 4

For technical questions, please call 1-800-444-3353.

SKU 68169

pacemaker interference or pacemaker failure. In addition, people with pacemakers should:

• Avoid operating alone.

• Do not use with power switch locked on.

• Properly maintain and inspect to avoid electrical shock.

• Any power cord must be properly grounded. Ground Fault Circuit

Interrupter (GFCI) should also be implemented – it prevents sustained electrical shock.

11. WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities, contains chemicals known [to the State of

California] to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

• Lead from lead-based paints

• Crystalline silica from bricks and cement or other masonry products

• Arsenic and chromium from chemically treated lumber

Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles. (California Health

& Safety Code § 25249.5, et seq.)

12. WARNING: Handling the cord on this product will expose you to lead, a chemical known to the State of California to cause cancer, and birth defects or other reproductive harm. Wash hands after handling. (California Health &

Safety Code § 25249.5, et seq.)

13. The warnings, precautions, and instructions discussed in this instruction manual cannot cover all possible

SKU 68169 conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator.

Vibration Safety

This tool vibrates during use. Repeated or long-term exposure to vibration may cause temporary or permanent physical injury, particularly to the hands, arms and shoulders. To reduce the risk of vibration-related injury:

1. Anyone using vibrating tools regularly or for an extended period should first be examined by a doctor and then have regular medical check-ups to ensure medical problems are not being caused or worsened from use. Pregnant women or people who have impaired blood circulation to the hand, past hand injuries, nervous system disorders, diabetes, or Raynaud’s Disease should not use this tool. If you feel any symptoms related to vibration (such as tingling, numbness, and white or blue fingers), seek medical advice as soon as possible.

2. Do not smoke during use. Nicotine reduces the blood supply to the hands and fingers, increasing the risk of vibration-related injury.

3. Wear suitable gloves to reduce the vibration effects on the user.

4. Use tools with the lowest vibration when there is a choice.

5. Include vibration-free periods each day of work.

6. Grip tool as lightly as possible (while still keeping safe control of it). Let the tool do the work.

For technical questions, please call 1-800-444-3353.

Page 5

7. To reduce vibration, maintain the tool as explained in this manual. If any abnormal vibration occurs, stop use immediately.

SAVE THESE

INSTRUCTIONS.

GROUNDING

TO PREVENT

ELECTRIC SHOCK

AND DEATH FROM INCORRECT

GROUNDING WIRE

CONNECTION:

Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded.

Do not modify the power cord plug provided with the tool.

Never remove the grounding prong from the plug. Do not use the tool if the power cord or plug is damaged. If damaged, have it repaired by a service facility before use. If the plug will not fit the outlet, have a proper outlet installed by a qualified electrician.

Double Insulated Tools: Tools with

Two Prong Plugs

Outlets for 2-Prong Plug

1. Tools marked “Double Insulated” do not require grounding. They have a special double insulation system which satisfies

OSHA requirements and complies with the applicable standards of Underwriters

Laboratories, Inc., the Canadian

Standard Association, and the National

Electrical Code.

2. Double insulated tools may be used in either of the 120 volt outlets shown in the preceding illustration.

(See Outlets for

2-Prong Plug.)

Extension Cords

1. Grounded tools require a three wire extension cord. Double Insulated tools can use either a two or three wire extension cord.

2. As the distance from the supply outlet increases, you must use a heavier gauge extension cord. Using extension cords with inadequately sized wire causes a serious drop in voltage, resulting in loss of power and possible tool damage.

(See Table A.)

3. The smaller the gauge number of the wire, the greater the capacity of the cord.

For example, a 14 gauge cord can carry a higher current than a 16 gauge cord.

(See Table A.)

4. When using more than one extension cord to make up the total length, make sure each cord contains at least the minimum wire size required.

(See

Table A.)

5. If you are using one extension cord for more than one tool, add the nameplate amperes and use the sum to determine the required minimum cord size.

(See

Table A.)

Page 6

For technical questions, please call 1-800-444-3353.

SKU 68169

6. If you are using an extension cord outdoors, make sure it is marked with the suffix “W-A” (“W” in Canada) to indicate it is acceptable for outdoor use.

7. Make sure the extension cord is properly wired and in good electrical condition.

Always replace a damaged extension cord or have it repaired by a qualified electrician before using it.

8. Protect the extension cords from sharp objects, excessive heat, and damp or wet areas.

RECOMMENDED MINIMUM WIRE GAUGE

FOR EXTENSION CORDS*

(120/240 VOLT)

NAMEPLATE

AMPERES

(at full load)

EXTENSION CORD

LENGTH

25’ 50’ 75’ 100’ 150’

0 – 2.0

18 18 18 18 16

2.1 – 3.4

18 18 18 16 14

3.5 – 5.0

5.1 – 7.0

7.1 – 12.0

12.1 – 16.0

16.1 – 20.0

TABLE A

18 18 16 14 12

18 16 14 12 12

18 14 12 10 -

14 12 10

12 10 -

-

-

-

-

* Based on limiting the line voltage drop to five volts at 150% of the rated amperes.

Symbology

Double Insulated

Canadian Standards Association

Underwriters Laboratories, Inc.

V~

Volts Alternating Current

A

Amperes n0 xxxx/min.

No Load Revolutions per Minute

(RPM)

SKU 68169

For technical questions, please call 1-800-444-3353.

Page 7

SPECIFICATIONS

Electrical

Input

120 V~ / 60 Hz / 7.5 A (Rated)

Motor Speed 0-2800 RPM

Drilling

Capacity

Chuck

Capacity

1/2” in Steel

5/8” in Masonry

1” in Wood

(Hammer Drill and Drill mode)

1/16” to 1/2”

Three Jaw Key Type

Depth Gauge (45)

Assembly

Chuck (3)

Figure 1

Side

Handle (46)

Power Cord (35)

Key Holder

UNPACKING

When unpacking, make sure that the item is intact and undamaged. If any parts are missing or broken, please call Harbor

Freight Tools at 1-800-444-3353 as soon as possible.

INSTRUCTIONS FOR PUTTING

INTO USE

Read the ENTIRE IMPORTANT

SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product.

TO PREVENT

SERIOUS INJURY

FROM ACCIDENTAL

OPERATION: Turn the Trigger

(32) off and unplug the tool from its electrical outlet before assembling or making any adjustments to the tool.

Note: For additional information regarding the parts listed in the following pages, refer to the Assembly Diagram near the end of this manual.

1. Loosen the grip on the Side Handle

(46) and slide Side Handle clamp over and behind the Chuck (3) until it is set against housing.

2. Rotate the Side Handle until it is in desired orientation. If you are righthanded, position the Side Handle so it extends from the left of the housing, as shown Figure 1 above.

3. Rotate Side Handle clockwise to secure the clamp.

4. To install the Depth Gauge (45), loosen the Side Handle and slide the Depth

Gauge into the gauge hole. See Figure

1, above.

5. Set Depth Gauge to required depth and retighten grip to fasten Depth Gauge into place (read further explanation under General Operating Instructions).

Page 8

For technical questions, please call 1-800-444-3353.

SKU 68169

OPERATING INSTRUCTIONS

Read the ENTIRE IMPORTANT

SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product.

3. If possible, secure loose work pieces using a vise or clamps (not included) to prevent movement while working, if possible.

4. There must not be objects, such as utility lines, nearby that will present a hazard while working.

Tool Set Up

TO PREVENT

SERIOUS INJURY

FROM ACCIDENTAL

OPERATION: Turn Tool off, unplug from its electrical outlet and remove Drill Chuck Key before adjusting tool or installing accessories.

The Hammer Drill is equipped with a keyed Chuck. Follow these steps to insert bit:

1. Insert Chuck Key (2) into the Chuck and turn counterclockwise to open the Chuck.

2. Insert the hammer bit or the drill bit (not included) all the way into the Chuck.

3. Turn the Chuck Key clockwise to tighten the Chuck on the bit. When not in use, the Key can be stored in the key holder on the Power Cord (35).

Work Piece and Work Area Set Up

1. Designate a work area that is clean and well-lit. The work area must not allow access by children or pets to prevent distraction and injury.

2. Route the power cord along a safe path to reach the work area without creating a tripping hazard or exposing the power cord to possible damage. The power cord must reach the work area with enough extra length to allow free movement while working.

General Operating Instructions

1. Plug Power Cord into a working outlet.

2. Set Direction Switch (40) to correct position. For clockwise (forward) rotation, push it from left side (Switch surface is marked with “R”). See Figure 2, below.

3. To rotate Chuck in a counterclockwise

(reverse) direction, push it from the left side (Switch surface is marked with “L”).

WARNING! Do not change rotation direction while the Chuck is rotating.

Direction

Switch (40)

Speed Control Knob

Figure 2

Figure 2

Trigger (32)

Trigger

Lock

Button

4. Verify bit is securely locked in Chuck.

5. Press Trigger to activate. Obeserve rotating bit, making sure it does not wobble. If it does, back off Chuck and reposition the bit.

SKU 68169

For technical questions, please call 1-800-444-3353.

Page 9

6. To adjust the drilling speed, rotate the speed control knob located in the center of the Trigger. Turn clockwise to increase speed and counterclockwise to decrease speed. See Figure 2.

7. For continuous drilling, press Trigger, then Trigger lock button on side of handle, and release Trigger. To release lock, depress Trigger. See Figure 2.

8. WARNING! Use both hands during use.

9. Use the Depth Gauge for controlled depth drilling. The Depth Gauge has two sets of markings on opposite ends of the gauge. One is in half inch increments and the other in one-centimeter increments (increments are not precise values, only general guides).

10. Insert bit and tighten Chuck. Loosen

Side Handle, place tip of bit against solid surface and extend Depth Gauge until it is against same surface. Determine required hole-depth and retract Gauge accordingly. Tighten Side Handle.

11. To switch between plain drilling and hammering mode (drilling with an oscillating hammer motion), slide the

Mode Selector (26) to left or right. The

“drill” symbol indicates plain drilling while the “hammer” symbol indicates hammer drilling. See Figure 3.

Hammer symbol

materials. Do not drill or hammer drill hard materials such as steel or concrete with Lock Button pressed

(ON). If drill bit catches on material, the high torque will cause the tool to twist around without stopping. This violent action could cause injury to your hands and arms. It could also damage the

Hammer Drill.

13. To prevent accidents, turn off the tool and disconnect its power supply after use. Clean, then store the tool indoors out of children’s reach.

Metal Drilling Tips

1. Use high speed steel, carbide or specialty bits for metal drilling.

2. Secure work piece to keep it from moving during the drilling operation.

3. Use a center punch (not included) to create a dimple for the bit to start.

4. Remove Key from Chuck.

5. Start by drilling slowly to keep bit from wandering/skating away from your starting point.

6. As hole is established, increase speed.

Do not use so much pressure that bit heats up. This can damage bit and create irregular hole. For hard metal, use cutting oil to keep bit cool.

7. When drilling large holes in metal, start by drilling a smaller pilot hole, then using a larger bit for the final size hole.

Mode

Selector (26)

(Top View)

12.

Drill symbol

Figure 3

WARNING! Use this continuous drill function ONLY when drilling soft

Page 10

Wood Drilling Tips

1. Use high speed bits or bits specially designed for wood drilling, such as brad point, spade bits, forstner bits, etc.

2. Secure work piece to keep it from moving during the drilling operation.

For technical questions, please call 1-800-444-3353.

SKU 68169

3. Start by drilling slowly to keep bit from wandering away from starting point.

Increase speed as hole is established.

4. To prevent or reduce “break out” when bit penetrates work piece, clamp a piece of scrap material to back of work piece.

5. Do not lock Trigger in the ON position, as the bit can easily jam in wood and motor must be stopped quickly.

Concrete Drilling Tips

1. Use carbide or specialty bits for concrete drilling.

2. Rock and masonry are generally drilled in the hammer (impact) drilling mode.

3. When drilling in walls, start with regular drilling and, once tile is pierced, continue with hammer mode.

NOTE: In deep bore holes, occasionally pull the drill bit out to remove dust and chips.

Recommended Drill Bits Sets

The chart below lists applicable Drill Bit sets that are available from Harbor Freight Tools.

SKU To Drill Into Sizes

32925

40547

Name

29-Piece High Speed Steel Drill

Bit Set

20-Piece 1/8” Shank Diamond

Point Set

Metals

Metals, Glass

1/16” to 1/2” by 64ths

1-3/4” overall length

1637 7-Piece Brad Point Wood Bit Set Wood

Wood

3” to 6” Length; Sizes: 1/8”, 3/16”,

1/4”, 5/16”, 3/8”, 7/16”, and 1/2” bits

5/16”, 3/8”, 7/16” 33449 3-Piece 25” Long Wood Bit Set

35837

29-Piece Brad Point Wood Drill

Bit Set

42256

46754

46755

5-Piece Quick Change Masonry

Drill Bits

5-Piece 12” SDS Masonry Bit

Set

5-Piece 16” SDS Masonry Bit

Set

Wood

Concrete/Masonry

Concrete/Masonry

Concrete/Masonry

Sizes: 1/16” through 1/2” by 64ths

5/32”, 3/16”, 1/4”, 5/16” and 3/8”

5/16”, 3/8”, 1/2”, 3/4”, and 1”

5/16”, 3/8”, 1/2”, 3/4”, 1”

SKU 68169

For technical questions, please call 1-800-444-3353.

Page 11

MAINTENANCE AND

SERVICING

Procedures not specifically explained in this manual must be performed only by a qualified technician.

TO PREVENT

SERIOUS INJURY

FROM ACCIDENTAL

OPERATION: Turn the Trigger off and unplug the tool from its electrical outlet before performing any inspection, maintenance, or any cleaning procedures.

TO PREVENT SERIOUS INJURY

FROM TOOL FAILURE:

Do not use damaged equipment.

If abnormal noise or vibration occurs, have the problem corrected before further use.

Cleaning, Maintenance, and

Lubrication

1. BEFORE EACH USE, inspect the general condition of the tool. Check for loose hardware, misalignment or binding of moving parts, cracked or broken parts, damaged electrical wiring, and any other condition that may affect its safe operation.

2. AFTER USE, wipe the tool with a clean cloth.

3. PERIODICALLY, and after each prolonged and extensive application, blow compressed air into the motor housing slots to remove any accumulated dirt and debris.

WARNING! If the supply cord of this power tool is damaged, it must be replaced only by a qualified service technician.

Page 12

For technical questions, please call 1-800-444-3353.

SKU 68169

Troubleshooting

Problem Possible Causes

Tool will not start. 1. Cord not connected.

2. No power at outlet.

Likely Solutions

1. Check that cord is plugged in.

2. Check power at outlet. If outlet is unpowered, turn off tool and check circuit breaker. If breaker is tripped, make sure circuit is right capacity for tool and circuit has no other loads.

3. Have technician service tool.

Tool operates slowly.

3. Internal damage or wear. (Carbon brushes or switch.)

Extension cord too long or wire size too small.

Performance decreases over time.

Excessive noise or rattling.

Overheating.

1. Accessory dull or damaged.

2. Carbon brushes worn or damaged.

Internal damage or wear. (Carbon brushes or bearings, for example.)

1. Forcing tool to work too fast.

2. Bit dull or damaged.

3. Blocked motor housing vents.

4. Motor being strained by long or small diameter extension cord.

5. Improper internal parts lubrication.

Eliminate use of extension cord. If an extension cord is needed, use shorter/heavier gauge cord.

See Extension Cords in GROUNDING section.

1. Keep cutting accessories sharp. Replace as needed.

2. Have qualified technician replace brushes.

Have technician service tool.

1. Allow tool to work at its own rate.

2. Keep bit sharp. Replace as needed.

3. Wear ANSI-approved safety goggles and NIOSHapproved dust mask/respirator while blowing dust out of motor using compressed air.

4. Eliminate use of extension cord. If an extension cord is needed, use one with the proper diameter for its length and load. See Extension Cords in

GROUNDING section.

5. Have a qualified technician service the tool using

ONLY white lithium grease.

Follow all safety precautions whenever diagnosing or servicing the tool.

Disconnect power supply before service.

SKU 68169

For technical questions, please call 1-800-444-3353.

Page 13

PLEASE READ THE FOLLOWING CAREFULLY

THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY

DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR

DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE

OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED

TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR

EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY

CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK

AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT

PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.

Part Description

1 Screw (M6x25)

2 Chuck Key

3 Chuck

4 Spindle

5 Spindle Key (3x10mm)

6 Circlip (M23)

7 Bearing (6002)

8 Front Gear

9 Back Gear

10 Gear box

11 Screw (ST4x20)

12 Circlip (M22)

13 Oil Seal

14 Inner Gear

15 Circlip (M12)

16 Spring

17 Seal Ring

18 Oil Seal

19 Support

20 Bearing (608)

21 Rotor

22 Bearing (607)

23 Impact Selector

PARTS LIST

Qty.

1

1

1

1

4

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

Part Description

24 Spring Cap

25 Spring

26 Mode Selector

27 Bearing (607)

28 Stator

29 Housing

30 O-Ring

31 Inductor

32 Trigger

33 Cord Clamp

34 Screw (ST4x14)

35 Power Cord

36 Cord Sleeve

37 Screw (ST2.9x12)

38 Carbon Brush

39 Brush Holder

40 Direction Switch

41 Capacitor

42 Screw (ST4x22)

43 Housing

44 Screw (ST4.2x16)

45 Depth Gauge

46 Side Handle

Qty.

2

2

1

4

2

1

1

1

1

1

1

1

1

1

1

1

6

1

1

1

1

1

1

Record Product’s Serial Number Here:

Note: If product has no serial number, record month and year of purchase instead.

Note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts.

Page 14

For technical questions, please call 1-800-444-3353.

SKU 68169

SKU 68169

For technical questions, please call 1-800-444-3353.

Page 15

LIMITED 90 DAY WARRANTY

Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries to persons or property, or for incidental, contingent, special or consequential damages arising from the use of our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS

OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.

To take advantage of this warranty, the product or part must be returned to us with transportation charges prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise. If our inspection verifies the defect, we will either repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will return repaired products at our expense, but if we determine there is no defect, or that the defect resulted from causes not within the scope of our warranty, then you must bear the cost of returning the product.

This warranty gives you specific legal rights and you may also have other rights which vary from state to state.

3491 Mission Oaks Blvd. • PO Box 6009 Camarillo, CA 93011 • (800) 444-3353

Page 16

For technical questions, please call 1-800-444-3353.

SKU 68169