advertisement
Implementing Avaya B5800 Branch
Gateway for a Communication Server 1000
Configuration
Release 6.2
03-604053
Issue 3
October 2012
© 2012 Avaya Inc.
All Rights Reserved.
Notice
While reasonable efforts have been made to ensure that the information in this document is complete and accurate at the time of printing, Avaya assumes no liability for any errors. Avaya reserves the right to make changes and corrections to the information in this document without the obligation to notify any person or organization of such changes.
Documentation disclaimer
“Documentation” means information published by Avaya in varying mediums which may include product information, operating instructions and performance specifications that Avaya generally makes available to users of its products. Documentation does not include marketing materials. Avaya shall not be responsible for any modifications, additions, or deletions to the original published version of documentation unless such modifications, additions, or deletions were performed by Avaya. End User agrees to indemnify and hold harmless
Avaya, Avaya's agents, servants and employees against all claims, lawsuits, demands and judgments arising out of, or in connection with, subsequent modifications, additions or deletions to this documentation, to the extent made by End User.
Link disclaimer
Avaya is not responsible for the contents or reliability of any linked websites referenced within this site or documentation provided by
Avaya. Avaya is not responsible for the accuracy of any information, statement or content provided on these sites and does not necessarily endorse the products, services, or information described or offered within them. Avaya does not guarantee that these links will work all the time and has no control over the availability of the linked pages.
Warranty
Avaya provides a limited warranty on its hardware and Software
(“Product(s)”). Refer to your sales agreement to establish the terms of the limited warranty. In addition, Avaya’s standard warranty language, as well as information regarding support for this Product while under warranty is available to Avaya customers and other parties through the
Avaya Support website: http://support.avaya.com
. Please note that if you acquired the Product(s) from an authorized Avaya reseller outside of the United States and Canada, the warranty is provided to you by said Avaya reseller and not by Avaya. “Software” means computer programs in object code, provided by Avaya or an Avaya Channel
Partner, whether as stand-alone products or pre-installed on hardware products, and any upgrades, updates, bug fixes, or modified versions thereto.
Licenses
THE SOFTWARE LICENSE TERMS AVAILABLE ON THE AVAYA
WEBSITE, HTTP://SUPPORT.AVAYA.COM/LICENSEINFO/ ARE
APPLICABLE TO ANYONE WHO DOWNLOADS, USES AND/OR
INSTALLS AVAYA SOFTWARE, PURCHASED FROM AVAYA INC.,
ANY AVAYA AFFILIATE, OR AN AUTHORIZED AVAYA RESELLER
(AS APPLICABLE) UNDER A COMMERCIAL AGREEMENT WITH
AVAYA OR AN AUTHORIZED AVAYA RESELLER. UNLESS
OTHERWISE AGREED TO BY AVAYA IN WRITING, AVAYA DOES
NOT EXTEND THIS LICENSE IF THE SOFTWARE WAS OBTAINED
FROM ANYONE OTHER THAN AVAYA, AN AVAYA AFFILIATE OR AN
AVAYA AUTHORIZED RESELLER; AVAYA RESERVES THE RIGHT
TO TAKE LEGAL ACTION AGAINST YOU AND ANYONE ELSE
USING OR SELLING THE SOFTWARE WITHOUT A LICENSE. BY
INSTALLING, DOWNLOADING OR USING THE SOFTWARE, OR
AUTHORIZING OTHERS TO DO SO, YOU, ON BEHALF OF
YOURSELF AND THE ENTITY FOR WHOM YOU ARE INSTALLING,
DOWNLOADING OR USING THE SOFTWARE (HEREINAFTER
REFERRED TO INTERCHANGEABLY AS “YOU” AND “END USER”),
AGREE TO THESE TERMS AND CONDITIONS AND CREATE A
BINDING CONTRACT BETWEEN YOU AND AVAYA INC. OR THE
APPLICABLE AVAYA AFFILIATE ( “AVAYA”).
Avaya grants you a license within the scope of the license types described below, with the exception of Heritage Nortel Software, for which the scope of the license is detailed below. Where the order documentation does not expressly identify a license type, the applicable license will be a Designated System License. The applicable number of licenses and units of capacity for which the license is granted will be one (1), unless a different number of licenses or units of capacity is specified in the documentation or other materials available to you.
“Designated Processor” means a single stand-alone computing device.
“Server” means a Designated Processor that hosts a software application to be accessed by multiple users.
License types
Designated System(s) License (DS). End User may install and use each copy of the Software only on a number of Designated Processors up to the number indicated in the order. Avaya may require the
Designated Processor(s) to be identified in the order by type, serial number, feature key, location or other specific designation, or to be provided by End User to Avaya through electronic means established by Avaya specifically for this purpose.
Copyright
Except where expressly stated otherwise, no use should be made of materials on this site, the Documentation, Software, or hardware provided by Avaya. All content on this site, the documentation and the
Product provided by Avaya including the selection, arrangement and design of the content is owned either by Avaya or its licensors and is protected by copyright and other intellectual property laws including the sui generis rights relating to the protection of databases. You may not modify, copy, reproduce, republish, upload, post, transmit or distribute in any way any content, in whole or in part, including any code and software unless expressly authorized by Avaya. Unauthorized reproduction, transmission, dissemination, storage, and or use without the express written consent of Avaya can be a criminal, as well as a civil offense under the applicable law.
Third-party components
Certain software programs or portions thereof included in the Software may contain software (including open source software) distributed under third party agreements (“Third Party Components”), which may contain terms that expand or limit rights to use certain portions of the
Software (“Third Party Terms”). Information regarding distributed Linux
OS source code (for those product that have distributed Linux OS source code) and identifying the copyright holders of the Third Party
Components and the Third Party Terms that apply is available in the
Documentation or on Avaya’s website at: http://support.avaya.com/
Copyright . You agree to the Third Party Terms for any such Third Party
Components.
Preventing Toll Fraud
“Toll fraud” is the unauthorized use of your telecommunications system by an unauthorized party (for example, a person who is not a corporate employee, agent, subcontractor, or is not working on your company's behalf). Be aware that there can be a risk of Toll Fraud associated with your system and that, if Toll Fraud occurs, it can result in substantial additional charges for your telecommunications services.
Avaya Toll Fraud Intervention
If you suspect that you are being victimized by Toll Fraud and you need technical assistance or support, call Technical Service Center Toll
Fraud Intervention Hotline at +1-800-643-2353 for the United States and Canada. For additional support telephone numbers, see the Avaya
Support website: http://support.avaya.com
. Suspected security vulnerabilities with Avaya products should be reported to Avaya by sending mail to: [email protected].
Trademarks
Avaya is a registered trademark of Avaya Inc.
Aura is a registered trademark of Avaya Inc.
2 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
All non-Avaya trademarks are the property of their respective owners, and “Linux” is a registered trademark of Linus Torvalds.
The trademarks, logos and service marks (“Marks”) displayed in this site, the Documentation and Product(s) provided by Avaya are the registered or unregistered Marks of Avaya, its affiliates, or other third parties. Users are not permitted to use such Marks without prior written consent from Avaya or such third party which may own the Mark.
Nothing contained in this site, the Documentation and Product(s) should be construed as granting, by implication, estoppel, or otherwise, any license or right in and to the Marks without the express written permission of Avaya or the applicable third party.
Downloading Documentation
For the most current versions of Documentation, see the Avaya
Support website: http://support.avaya.com
.
Contact Avaya Support
See the Avaya Support website: http://support.avaya.com
for product notices and articles, or to report a problem with your Avaya product.
For a list of support telephone numbers and contact addresses, go to the Avaya Support website: http://support.avaya.com
, scroll to the bottom of the page, and select Contact Avaya Support.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 3
4 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Contents
Chapter 2: CS 1000 and B5800 Branch Gateway deployments......................................
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 5
Chapter 6: About preserving staged button programming for BST phones.................
Chapter 7: Upgrading an R6.2 system with an R6.2 service pack..................................
6 Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012
Chapter 10: Managing B5800 Branch Gateways from System Manager.......................
Restrictions when editing a B5800 Branch Gateway system configuration from System Manager. 160
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 7
Disabling the System Manager administration feature for the branch from System Manager......... 162
Configuration changes performed through Manager that cannot be synced with System Manager 164
Chapter 15: Standalone SAL Gateway for remote service..............................................
8 Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 9
Appendix A: Avaya port matrix for B5800 Branch Gateway and SIP phones...............
10 Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012
Appendix E: Recommended courses for Avaya B5800 Branch Gateway training.......
Appendix F: T7000 and M7000 Series Digital Deskphones.............................................
Appendix G: 1100 Series and 1200 Series IP Deskphones.............................................
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 11
12 Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012
Chapter 1: B5800 Branch Gateway overview
The Avaya B5800 Branch Gateway is a flexible, cost-effective communications platform for enterprise branch offices. It enables access via SIP to Avaya Aura
®
Session Manager in the enterprise center, optional access to centralized PSTN trunking, and access to centralized applications, such as conferencing, messaging, and more. The B5800 Branch Gateway solution provides centralized management by Avaya Aura ® System Manager and centralized licensing by WebLM.
B5800 Branch Gateways are deployed in the distributed branch user model. In the distributed branch user model, call processing for the branch phones is provided locally. Non-IP phones are connected to the
B5800 Branch Gateway and IP and certain SIP endpoints (not including the Avaya 9600 SIP phones) can be administered with B5800 Branch Gateway as their controller (see
on page 23 for more information). Access to and from the rest of the Avaya Aura ® network is via the B5800 Branch
Gateway system's Avaya Aura
®
Session Manager link across the enterprise WAN. This connection allows for VoIP connectivity to other B5800 Branch Gateway systems, to centralized PSTN trunking, and to centralized applications such as conferencing and Avaya Aura ® Messaging. The centralization capability is based primarily on the infrastructure at the enterprise core. The local B5800 Branch Gateway can be accessed as a SIP gateway connected to the core Avaya Aura ® Session Manager to provide access to local PSTN trunks and services when required.
Beginning in R6.2, B5800 Branch Gateway is supported in an Avaya Communication Server 1000 (CS
1000) configuration. B5800 Branch Gateway can be deployed as a new branch in an existing CS 1000 configuration or as a replacement for Business Communications Manager (BCM) as a branch office in a
CS 1000 branch office model. In these deployments, B5800 Branch Gateway operates as a distributed branch.
Note:
Integration of B5800 Branch Gateway in an Avaya Aura
®
configuration is provided in a separate document. See Implementing the Avaya B5800 Branch Gateway for an Avaya Aura
®
Configuration, document number 18-603853.
PSTN trunking configurations
With the ability to administer call control at both the B5800 Branch Gateway and the Avaya
Aura ® Session Manager, there are many ways you can optimize external PSTN trunk usage.
The B5800 Branch Gateway is a full PABX and by default uses its own PSTN trunks. However it can be configured to make and receive external calls via the central Avaya Aura
®
Session
Manager or NRS. A combination of these methods can be used for PSTN calls based on the
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 13
B5800 Branch Gateway overview
Voicemail support options
B5800 Branch Gateway supports a range of options for voicemail services to the branch's native users. It supports Embedded Voicemail for native branch users and auto attendants to service local PSTN trunks. Standalone Voice Mail is also available for B5800 Branch Gateway systems when additional port capacity is required. A centralized voicemail system, either CS
1000 CallPilot or Avaya Aura Messaging connected via Session Manager, can also be configured. When using CallPilot or Avaya Aura Messaging, you are still able to use Embedded
Voicemail or Standalone Voice Mail at each branch to provide auto-attendant operation and
announcements for waiting calls. For more information, see Voicemail options on page 173.
Management
The primary method for configuring and managing the branches in a B5800 Branch Gateway system is centrally using Avaya Aura
®
System Manager R6.2. Avaya Aura
®
System Manager is a central management system that delivers a set of shared management services and a common console for different components of the Avaya Aura ® solution. System Manager provides a single access interface to administer multiple branch locations and multiple distributed B5800 Branch Gateway users. System Manager also launches IP Office Manager in the appropriate mode where you can remotely administer individual B5800 Branch
Gateways.
As an alternative to System Manager, you can use IP Office Manager that is directly connected to the B5800 Branch Gateway to configure a branch locally when you need to administer an isolated branch or System Manager is not available. IP Office Manager is an application for viewing and editing a B5800 Branch Gateway system's configuration. It is included in the
B5800 Branch Gateway administration software suite. Manager is an off-line editor. It receives a copy of the system's current configuration settings. After changes are made to that copy and the file is saved, Manager automatically sends the file back to the system for those changes to become active.
Avaya Aura ® System Manager
Using Avaya Aura
®
System Manager R6.2, you are able to:
• Upgrade B5800 Branch Gateway systems.
• Add B5800 Branch Gateway devices from the network to System Manager.
• Create B5800 Branch Gateway endpoint templates that are used to create B5800 Branch
Gateway users. These templates can be edited, duplicated, or deleted.
14 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Management
• Create B5800 Branch Gateway system configuration templates that can be applied to selected B5800 Branch Gateway systems. These templates are used for initial device provisioning. These templates can be edited, duplicated, or deleted.
• Upload and convert audio files to System Manager to be used in the B5800 Branch
Gateway System Configuration Auto Attendant feature.
• Manage B5800 Branch Gateway system configurations. From System Manager, you are able to launch IP Office Manager to view or edit a system configuration. With this feature, you make changes to the B5800 Branch Gateway device through System Manager. You are able to apply the changes immediately or schedule the changes to run at a specified time.
• Manage B5800 Branch Gateway security configuration. From System Manager, you are able to launch IP Office Manager to view or edit a system security configuration. With this feature, you make changes directly to the B5800 Branch Gateway device.
• Create B5800 Branch Gateway user templates. These templates can be edited or deleted.
• Perform a B5800 Branch Gateway backup with the option of storing the backup output in
System Manager or creating a local backup where the system stores the backup output on the local storage attached to the B5800 Branch Gateway device.
• Perform a B5800 Branch Gateway restore. This feature allows you to restore:
- a saved B5800 Branch Gateway system configuration onto a B5800 Branch
Gateway from System Manager.
- a backup of a B5800 Branch Gateway system configuration onto a B5800 Branch
Gateway from the device SD card.
- users from System Manager to the B5800 Branch Gateway.
- a saved B5800 Branch Gateway system configuration and user from System
Manager onto a B5800 Branch Gateway.
• View events and alarms regarding various operations that occur on the B5800 Branch
Gateway.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 15
B5800 Branch Gateway overview
About upgrading B5800 Branch Gateways
With the introduction of centralized management provided by Avaya Aura
®
System Manager, you are able to upgrade B5800 Branch Gateway firmware and software from System Manager.
You are also able to upgrade an individual B5800 Branch Gateway system from IP Office
Manager installed on an administration PC that is connected directly to the system. You can perform an upgrade from IP Office Manager using the upgrade wizard or the System SD card.
For more information about these upgrade methods, see the following topics:
•
Upgrading the B5800 Branch Gateway using System Manager
on page 101
•
Using the upgrade wizard on page 219
•
System upgrade using the System SD card
on page 258
Licensing
B5800 Branch Gateway supports centralized licensing by WebLM where a single license file is generated in Avaya Product Licensing and Delivery System (PLDS) for multiple branches.
16 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Licensing
Support for individual PLDS license files for each branch (the licensing method provided in
B5800 Branch Gateway R6.1) is also an option. WebLM licensing is the recommended method for B5800 Branch Gateway R6.2 and higher. Both licensing methods are described below.
WebLM license management
B5800 Branch Gateway R6.2 supports WebLM licensing in which a single license file is generated in PLDS for multiple branches. This license file contains the host ID of the WebLM server and is managed by the WebLM server. Each B5800 Branch Gateway communicates with the WebLM server to request the required license entitlements. B5800 Branch Gateway uses the Avaya Aura System Manager WebLM server.
Two configuration models are supported:
• WebLM standard licensing model — in this model, one WebLM server is used. This model is used for enterprises where the System Manager WebLM server is able to manage all
B5800 Branch Gateway licenses required for the enterprise.
• WebLM enterprise licensing model — in this model, multiple WebLM servers are used.
This model is used for enterprises where the licenses required for all branches in the enterprise exceed the System Manager WebLM server capacity. One WebLM server acts as a master WebLM server and hosts the license file from PLDS. The other WebLM servers(s) act as a local WebLM server and host allocation license files from the master
WebLM server. Each B5800 Branch Gateway must be configured with the IP address of one of the WebLM servers.
Note:
The expected System Manager WebLM server capacity is about 400 branches on a loaded
System Manager. The capacity would be higher on a lightly loaded System Manager. The expected WebLM capacity on a standalone Linux server is about 1,100 branches. Large deployments that exceed the System Manager WebLM capacity require additional standalone WebLM server(s) and configuration of the WebLM servers as master and local in the WebLM enterprise licensing model.
Note:
The correct expiration time of licenses for a B5800 Branch Gateway that uses a local WebLM server is provided on the corresponding master WebLM server. The local WebLM server shows the licenses as having an expiration time of 30 days or less. However, periodically the license expiration time on the local WebLM server is automatically refreshed and extended when the master WebLM server pushes a refreshed Allocation License File to the local WebLM.
For more information about WebLM licensing, see Administering Avaya WebLM (standalone) and Avaya WebLM Administration Guide.
Separate PLDS license for each branch
In B5800 Branch Gateway R6.1, an individual PLDS license file was required for each branch and installed on each branch directly. A WebLM server was not required. This licensing method is supported in B5800 Branch Gateway R6.2 for branches that cannot be connected via an enterprise WAN to a central WebLM server or for migration of installed B5800 Branch Gateway
R6.1 systems. Using the WebLM licensing method is recommended, but does not have to be done as part of an R6.1 to R6.2 upgrade.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 17
B5800 Branch Gateway overview
For the separate PLDS licensing method, branch licenses are issued and validated against the Feature Key serial number of the System SD card used by that B5800 Branch Gateway.
That number is printed after the FK prefix on the System SD card and is also shown in the branch system configuration. This means that licenses issued for one branch cannot be used in the configuration of another branch. In the IP Office Manager application, this number appears in the PLDS Host ID field on the System page when you select System > System.
B5800 Branch Gateway licenses
The B5800 Branch Gateway licenses are described below.
Avaya Branch Gateway System Software license
This license is required for operation of the B5800 Branch Gateway system. This license does not include any implicit entitlements and therefore is not sufficient by itself for branch operation without additional Station and/or SIP Trunk Session licences. One Avaya Branch Gateway
System Software license is required.
Native Station licenses
All users on a B5800 Branch Gateway system must be licensed by the addition of Native
Station licenses. Native Station licenses are required for all configured users with analog, digital, H.323 or DECT extensions; for users without any extension; and for all users with SIP extensions set as native (or local) (that is, extensions operating in the distributed branch user model).
Warning:
Unlicensed extensions will display No License Available but will be able to make emergency calls, i.e. calls that match B5800 Branch Gateway Dial Emergency short codes.
Embedded Messaging Ports license
This license is required if you are using the B5800 Branch Gateway voicemail options,
Embedded Voicemail or Standalone Voice Mail. The Embedded Messaging Ports license is also used to control the number of ports on systems where Call Pilot is configured as the central voicemail system and the local Embedded Voicemail provides auto attendant operation. For
Embedded Voicemail, up to 6 ports can be licensed. For Standalone Voice Mail, up to 40 ports can be licensed. At least one Embedded Messaging Port license must be purchased to enable this service.
SIP Trunk Sessions license
This license refers to the total number of concurrent sessions allowed on all SIP connections to the B5800 Branch Gateway. The maximum number of SIP trunk sessions is 128. SIP trunks provide the SIP connections between Avaya Aura ® Session Manager and B5800 Branch
Gateway.
Additional channels licenses
The PRI Universal (PRI-U) trunk card can be used in the B5800 Branch Gateway system. The
PRI-U ports can be configured to support E1, E1R2, or T1 line types. Each port supports 8 B
18 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
License modes channels which do not require a license. Additional B channels beyond these 8 require a license. There are two additional channels licenses that define the number of additional channels (above the default 8):
• Additional T1 Channels license — This license is for additional T1 trunks.
• Additional E1 Channels license — This license is for additional E1 or E1R2 trunks.
For trunk types on which channels can be set as in service, the licenses are consumed by those channels which are configured as being in service. Manager will block attempts to configure PRI channels as in service if they exceed the 8 per port allowed by default on that card and if there are no Additional T1 Channels or Additional E1 Channels licenses available.
120-day trial license
This license provides a 120-day trial period during which you have access to the features, functions, and capabilities available in B5800 Branch Gateway. After the expiration of the 120day trial license, the 30-day grace period is activated. At the end of the 30-day grace period, if no other license is installed or available, system administration is blocked, except for administration that fixes the licensing errors.
License modes
The B5800 Branch Gateway system can be in one of three license modes — License Normal
Mode, License Error Mode, and License Restricted Mode. The license mode, as well as any license errors, are displayed in IP Office Manager.
License Normal Mode
No license errors are present. The B5800 Branch Gateway can access the WebLM server and obtain the required license entitlements. If the licensing method is used where an individual
PLDS license file is required for each branch, a valid license file is installed on the B5800
Branch Gateway with sufficient entitlements.
License Error Mode
One or more license errors are present. The B5800 Branch Gateway initiates a 30–day license grace period during which time the system issues errors and alarms, but continues to provide normal operation as in License Normal Mode. Calls are allowed and/or blocked based on current configuration parameters and configured users can register, regardless of licensing status. The license errors must be fixed either by installing a valid license file with the appropriate licenses or by changing the configuration so that it does not exceed any license capacities.
License Restricted Mode
One or more license errors are present and the 30–day license grace period has expired.
B5800 Branch Gateway prevents any administrative changes except those that fix the licensing errors. While administration is restricted, dynamic system operation (such as making calls) continues based on the current configuration parameters, regardless of licensing status.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 19
B5800 Branch Gateway overview
System components
The B5800 Branch Gateway system is comprised of the following hardware components.
• B5800 Branch Gateway control unit — B5800 Branch Gateway is supported on the
IP500v2 platform or on the B5800 Branch Gateway hardware platform which is based on
IP500v2. The B5800 Branch Gateway control unit stores the system configuration and performs the routing and switching for telephone calls and data traffic. It includes 4 slots for optional base cards to support trunk and phone extension ports. The slots are numbered 1 to 4 from left to right. They can be used in any order; however, if the capacity for a particular type of card is exceeded, the card in the right-most slot will be disabled.
• B5800 Branch Gateway System SD card — The B5800 Branch Gateway System SD card is a specific Avaya SD card that is required. It determines the system operation as
B5800 Branch Gateway. It is uniquely numbered and has a serial number that must be used as the Host ID in the PLDS license file if the B5800 Branch Gateway is operating with an individual license file and not with WebLM licensing. The B5800 Branch Gateway
System SD card also provides Embedded Voicemail support and storage for system software files. The card fits into a slot in the rear of the control unit.
• Base cards — The control unit has slots for up to 4 base cards. The base cards are used to add analog extension ports, digital extension ports, and voice compression channels.
Each base card includes an integral front panel with ports for cable connections. The following base cards are supported:
- Digital station base card — This card provides 8 digital station (DS) ports for the connection of Avaya digital phones other than IP phones. The card can be fitted with a trunk daughter card which uses the base card ports for trunk connection. A maximum of 3 digital station base cards are allowed per control unit.
- Analog phone base card — This card is available in two variants, supporting either
2 or 8 analog phone ports. The card can be fitted with a trunk daughter card which uses the base card ports for trunk connection. A maximum of 4 analog phone base cards are allowed per control unit. The analog phone ports do not include a ringing capacitor. Where this is a requirement, connection should be via a Master socket containing ringing capacitors. If fitted with an analog trunk daughter card, during power failure phone port 8 is connected to analog trunk port 12.
- VCM base card — This card is available in variants supporting either 32 or 64 Voice
Compression Channels (VCM) for use with VoIP calls. A maximum of 2 VCM base cards are allowed per control unit. The card can be fitted with a trunk daughter card which uses the base card ports for trunk connection.
- 4–port expansion base card — This card adds an additional 4 expansion ports for external expansion modules. The card is supplied with four 2m yellow interconnect cables. This card does not accept any trunk daughter cards. A maximum of 1 4–port
expansion base card is allowed per control unit (right-hand slot 4 only). See External
20 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
System components
expansion modules on page 22 for a list of the supported external expansion
modules.
- BRI combination card — This card provides 6 digital station ports (1-6), 2 analog extension ports (7-8) and 2 BRI trunk ports (9-10, 4 channels). The card also includes
10 VCM channels. This card has a pre-installed BRI trunk daughter card. A maximum of 2 BRI combination cards of any type are allowed per control unit.
- ATM combination card — This card provides 6 digital station ports (1-6), 2 analog extension ports (7-8) and 4 analog trunk ports (9-12). The card also includes 10 VCM channels. This card has a pre-installed analog trunk daughter card. A maximum of
2 ATM combination cards of any type are allowed per control unit. The analog phone ports do not include a ringing capacitor. Where this is a requirement, connection should be via a Master socket containing ringing capacitors. If fitted with an analog trunk daughter card, during power failure phone port 8 is connected to analog trunk port 12.
- TCM 8 card — This card provides 8 digital station ports (1-8).
• Trunk daughter cards — Most base cards can be fitted with a trunk daughter card to support the connection of trunks to the base card. The following trunk daughter cards are supported:
- Analog trunk card — This card allows the base card to support 4 analog loop-start trunks. The analog phone ports do not include a ringing capacitor. Where this is a requirement, connection should be via a Master socket containing ringing capacitors.
If fitted with an analog trunk daughter card, during power failure phone port 8 is connected to analog trunk port 12. A maximum of 4 analog trunk cards are allowed per control unit.
- BRI trunk card — This card allows the base card to support up to 4 BRI trunk connections, each trunk providing 2B+D digital channels. The card is available in 2 port (4 channels) and 4 port (8 channels) variants. A maximum of 4 BRI trunk cards are allowed per control unit. For S-Bus connection, the card can be switched from
To trunk mode to So mode. This mode requires additional terminating resistors and an ISDN crossover cable connection.
- PRI trunk card — This card allows the base card to support up to 2 PRI trunk connections. The card is available in single and dual port variants. The card can be configured for E1 PRI, T1 robbed bit, T1 PRI or E1R2 PRI trunks. A maximum of 4
PRI trunk cards are allowed per control unit. The B5800 Branch Gateway system supports 8 unlicensed B-channels on each IP500 PRI-U port fitted. Additional Bchannels, up to the capacity of ports installed and PRI mode selected require
Universal PRI (Additional Channels) licenses added to the configuration. These additional channels consume the licenses based on which additional channels are configured as in-service from port 9 of slot 1 upwards. D-channels are not affected by licensing.
• Combination cards — Combination cards are pre-paired base and trunk daughter cards.
They provide 6 digital station ports, 2 analog phone ports, 10 VCM channels and either
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 21
B5800 Branch Gateway overview
4 analog trunk ports or 4 BRI channels (2 ports). The trunk daughter card cannot be removed or replaced with another type of trunk daughter card.
• External expansion modules — External expansion modules are used to add additional analog and digital ports. If the control unit is fitted with a 4–port expansion base card, then up to 12 external expansion modules are supported. The following external expansion modules are supported:
- Analog trunk module — This module rovides an additional 16 analog ports for connection of analog trunks. It supports both loop-start and ground-start trunks.
- BRI So8 module — This module provides 8 ETSI BRI-So ports for the connection of ISDN devices. This module is not intended to support BRI trunks.
- Digital station module — This module provides, depending on variant, an additional 16 or 30 DS ports for supported Avaya digital phones.
- Phone module — This module provides, depending on variant, an additional 16 or
30 phone ports for analog phones.
• Power supplies — The control unit has an internal power supply unit. Each external expansion module is supplied with an external power supply unit. Additional power supply units may also be required for IP phones and some phone add-ons.
• Power cords — Depending on the locale, different power cords need to be ordered for each control unit, external expansion module, and any phones or devices using external power supply units.
• Mounting kits — The control unit can be used free-standing, with external expansion modules stacked above it. With optional rack mounting kits, the control unit and external expansion modules can also be rack mounted. Alternatively, with an optional wall mounting kit the control unit can be wall mounted. However, the control unit cannot support any external expansion modules when wall mounted.
• Surge protectors and barrier boxes — Where the installation includes extensions in other buildings, additional protective equipment is required. This equipment may also be required in areas where the lightning risk is high.
• Phones — B5800 Branch Gateway systems support a variety of Avaya digital and IP phones plus analog phones.
• Application DVDs — The B5800 Branch Gateway applications can be ordered on a number of DVDs. In addition they can be downloaded from the B5800 Branch Gateway section of the Avaya support web site (http://support.avaya.com).
22 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Supported telephones
Supported telephones
Analog
1120E SIP
1140E SIP
1220 SIP
1230 SIP
1403 digital
1408 digital
1416 digital
1603
1603SW
1608
1616
1603SW-I
1608-I
1616-I
BM32 (DSS)
2402D
2410D
2420
3616 wireless
3620 wireless
3626 wireless
3641 wireless
3645 wireless
3720 DECT R4
3725 DECT R4
Telephone Native extensions (local extensions operating in the distributed branch user model)
1
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 23
B5800 Branch Gateway overview
Telephone
3740 DECT R4
3749 DECT R4
3810 digital wireless
4601
4602IP
4602SW
4610IP
4610SW
4621
4625
5402
5410
5420
EU24 (DSS)
5601
5602IP
5602SW
5610IP
5610SW
5620
5621
EU24 BL (DSS)
9504 digital
9508 digital
9608
9611G
9621G
9641G
9620L
9620C
Native extensions (local extensions operating in the distributed branch user model)
24 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
1
1
2
2
2
2
2
2
October 2012
Supported telephones
Telephone
9630G
9640
9640G
9650
9650C
SBM24
Avaya 1010/1020/1030/1040 video conferencing units
B149 conference phone
B159 conference phone
B179 conference phone
BM12
BCM TDM sets:
• DECT handsets 4xxx/7xxx series
• T7316E
• T7316
• T7406E
• T7406
• T7208
• T7100
• T7000
• M7310
• M7310N
• M7310+BLF
• M7324
• M7324N
• M7208
• M7208N
• M7100
• M7100N
Native extensions (local extensions operating in the distributed branch user model)
2
2
2
1
2
2
1
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 25
B5800 Branch Gateway overview
Telephone Native extensions (local extensions operating in the distributed branch user model)
• Audio conference unit
• T24 KIM (Key Indicator Module for
T7316)
DevConnect–approved 3rd-party SIP audio and video endpoints
1
When connected to their respective telephones.
2 Supported when running H.323 firmware; not supported when running SIP firmware.
Software applications
The B5800 Branch Gateway software applications are provided on DVDs.
• User applications — The following applications are supported for use by native users on a B5800 Branch Gateway system.
- Embedded Voicemail: supports basic voicemail mailbox operation, simple autoattendants and hunt group announcements. It is provided on the Avaya SD card.
Embedded Voicemail on a B5800 Branch Gateway system provides 6 ports. This
voicemail option requires a license. See Licensing
on page 16 for more information.
- Standalone Voicemail: provides additional port capacity (40 ports) on a Linux server. You must have a Linux server installed to use this option. This voicemail option requires a license. See
Licensing on page 16 for more information.
- SoftConsole: is intended for telephone system operators or receptionists. It displays details of calls and allows them to quickly see the status of the callers required destination and transfer the call. The SoftConsole user is able to access a range of details about the status of users and groups on the B5800 Branch Gateway system.
Up to 4 simultaneous SoftConsole users can be configured. This application does not require a license.
• Installer/maintainer applications — The following B5800 Branch Gateway applications are used to program and maintain a B5800 Branch Gateway system. These applications do not require a license.
- Manager: a configuration application used to access all parts of the B5800 Branch
Gateway configuration. Different levels of access can be defined to control which parts of the configuration the Manager user can view and alter. Manager is also used to upgrade the software files used by a B5800 Branch Gateway system.
26 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Supported country locales
- System Status: a monitoring application used to inspect the current status of B5800
Branch Gateway lines and extensions and to view records of recent alarms and events. It runs as a Java application.
- System Monitor: shows a trace of all activity on the B5800 Branch Gateway system in detail. Interpretation of System Monitor traces requires a high-level of data and telephony protocol knowledge. B5800 Branch Gateway installers and maintainers must run System Monitor when Avaya requests copies of System Monitor traces to resolve support issues.
- SNMP MIBs: Not an application as such, the SNMP MIB files can be used by 3rdparty SNMP applications to monitor the B5800 Branch Gateway system.
Supported country locales
When a new or defaulted system's configuration is first opened in Manager, the value set in the Locale field (System > System > Locale) should always be checked and changed if necessary. The system's locale sets factors such as the default ringing patterns and caller display settings. The locale also controls the language that a voicemail server will use for prompts.
The following table indicates locale settings supported for different functions. Note that this does not necessarily indicate support, availability or approval for B5800 Branch Gateway within that country.
Locale
Argentina
Australia
Belgium
Belgium
Brazil
Canada
Chile
China
Colombia
Language Telephony Phone
Display
Applications
Manager Soft
Console
Latin
Spanish
UK English
Dutch
French
Brazilian
Canadian
French
-
Latin
Spanish
Mandarin
Latin
Spanish
-
EVM and
SVM *
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 27
B5800 Branch Gateway overview
Locale
Denmark
Finland
France
Germany
Language Telephony Phone
Display
Danish -
Applications
Manager Soft
Console
Suomi
French
German
Greece Greek
Hong Kong Cantonese
-
-
-
-
-
-
-
Hungary
Iceland
India
Hungarian
Icelandic
UK English -
-
-
-
-
-
-
Italy
Korea
Italian
Korean
Mexico Latin
Spanish
Netherlands Dutch
New Zealand UK English
Norway Norwegian
Peru
Poland
Latin
Spanish
Polish -
-
-
-
EVM and
SVM *
-
SVM only
-
SVM only
SVM only
*
EVM is Embedded Voicemail. SVM is Standalone Voice Mail.
Note:
Hungarian, Polish, and Greek are not supported by Embedded Voicemail, but they are supported by Standalone Voice Mail.
• Locale: The country represented by the locale.
• Language: The voicemail prompt language used for that locale.
• Telephony: The B5800 Branch Gateway provides default telephony settings matching the normal expected defaults for the locale.
• Phone Display: Indicates that display messages from the B5800 Branch Gateway to
Avaya phones can be sent using the appropriate language for that locale. Note that the user locale can be used to override the system locale for these messages. Note also that some phones support their own language selection options for menus displayed by the phone's own software.
28 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Related resources
• Manager: Indicates that the IP Office Manager application can run in the specific locale language. Manager uses the best match it has (French, German, Brazilian, Dutch, Italian,
Mexican Spanish, Russian, or US English) for the regional location setting of the PC on which it is running, otherwise it defaults to UK English. If required the language used within the Manager screens can be overridden.
• Embedded Voicemail: Indicates that the locale is recognized by Embedded Voicemail and appropriate language prompts are then used. If an unsupported locale is used,
Embedded Voicemail will attempt the best match using the first two characters of the locale. The system locale can be overridden by setting a different user locale.
• Standalone Voice Mail: Indicates that the locale is recognized by Standalone Voice Mail and appropriate language prompts are then used. If an unsupported locale is used,
Standalone Voice Mail will attempt the best match using the first two characters of the locale. The system locale can be overridden by setting a different user locale.
Related resources
Related documents
Ensure that you have read this manual before starting the installation. Also read the installation documentation for any other equipment and applications being installed as part of the B5800
Branch Gateway system.
Documents you may need to consult are as follows:
• Administering Avaya Aura ® System Manager
• Administering Avaya Aura ® Session Manager, document number 03-603324
• Avaya IP Office Manager Release 6.2, document number 15-601011
• Unified Communications Management, Common Services Fundamentals, Avaya
Communication Server 1000, document number NN43001-116
• Security Management Fundamentals, Avaya Communication Server 1000, document number NN43001-604
• Network Routing Service Fundamentals, Avaya Communication Server 1000, document number NN43001-130
• Avaya CallPilot Administrator Guide, document number NN44200-601
• CS 1000 System and CallPilot Server Configuration, document number NN44200-312
• CallPilot Telephone Administration Guide, document number NN40090-500
• IP Peer Networking Installation and Commissioning – Avaya Communication Server
1000, document number NN43001-313
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 29
B5800 Branch Gateway overview
• SIP Line Fundamentals – Avaya Communication Server 1000, document number
NN43001-508
• Element Manager System Reference – Administration, document number NN43001-632
• Software Input Output Reference – Administration, document number NN43001-611
• SIP Software for Avaya 1100 Series IP Deskphones–Administration, document number
NN43170–600
• SIP Software for Avaya 1200 Series IP Deskphones–Administration, document number
NN43170–601
Avaya Mentor videos
Avaya Mentor is an Avaya-run channel on YouTube that includes technical content on how to install, configure, and troubleshoot Avaya products.
Visit http://www.youtube.com/AvayaMentor and do one of the following:
• Enter a key word or key words in the Search channel to search for a specific product or topic.
• Click the name of a playlist to scroll through the posted videos.
Training
Avaya University provides a wide range of training courses for B5800 Branch Gateway and its associated applications. This includes courses necessary for B5800 Branch Gateway resellers to become Avaya Authorized Channel Partners and for individuals to achieve B5800 Branch
Gateway certification.
Details of courses can be found on the Avaya University web site ( http://www.avayalearning.com
). The site can be used to check course availability and to book courses. It also includes on-line courses and on-line course assessments. The site requires users to setup a user name and password in order to track their personal training record.
For a list of recommended courses available for the B5800 Branch Gateway, see
Recommended courses for Avaya B5800 Branch Gateway training on page 305.
Web sites
Information to support B5800 Branch Gateway can be found on a number of web sites.
• Avaya ( http://www.avaya.com
)
30 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Revision history
The official web site for Avaya. The front page also provides access to individual Avaya web sites for different countries.
• Avaya Enterprise Portal ( http://partner.avaya.com
)
This is the official web site for all Avaya Business Partners. The site requires registration for a user name and password. Once accessed, the site portal can be individually customized for what products and information types you wish to see and to be notified about by email.
• Avaya Support ( http://support.avaya.com
)
Contains documentation and other support materials for Avaya products.
• Avaya University ( http://www.avaya-learning.com
)
This site provides access to the full range of Avaya training courses. That includes both on-line courses, course assessments and access to details of classroom based courses.
The site requires users to register in order to provide the user with access to details of their training record.
• Avaya Community ( http://www.aucommunity.com
)
This is the official discussion forum for Avaya product users. However it does not include any separate area for discussion of B5800 Branch Gateway issues.
Revision history
Issue
2
3
Date
07/2012
Summary of changes
• The name of the B5800 Branch Gateway security certificate cannot contain spaces. This is explained in a note in the appropriate places.
• The order of the steps in the “Configuration checklist” have been changed. The step to add the B5800 Branch Gateway to System
Manager has been moved to after you generate a certificate and run the Initial Installation Utility.
10/2012 Modifications have been made to the following procedures:
• “Generating a certificate on System Manager” (Additional steps have been added to the procedure for clarity.)
• “Using the Initial Installation Utility” (It is recommended to select LAN1 to configure the WAN interface.)
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 31
B5800 Branch Gateway overview
Issue Date Summary of changes
• “Configuring the B5800 Branch Gateway for certificates” (This procedure replaces “Manually loading the certificate to the B5800
Branch Gateway.)
• “Adding distributed users to System Manager” (Distributed H.323
users and SIP users do not require different configuration when being added to System Manager.)
32 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Chapter 2: CS 1000 and B5800 Branch
Gateway deployments
B5800 Branch Gateway in CS 1000 deployments supports all phones listed in Supported telephones on
page 23. Note that Norstar and BCM Digital T&M Series phones and 11xx and 12xx phones which may already be deployed in CS 1000 environments are supported in CS 1000 and B5800 Branch Gateway deployments.
Note:
The 11xx and 12xx phones must be upgraded to SIP 4.3 firmware to be supported on the B5800 Branch
Gateway.
CS 1000 and B5800 Branch Gateway deployments support two distributed branch configuration options as follows:
•
Option 1 on page 34 — CS 1000 and B5800 Branch Gateway reside as peers and the SSG must
be re-assigned to support Session Manager.
•
Option 2 on page 35 — CS 1000 and B5800 Branch Gateway reside as peers and an additional
SSG is required to support Session Manager.
The distributed branch configurations include Session Manager as part of the CS 1000 core. SIP interoperability between B5800 Branch Gateway and CS 1000, as well as between B5800 Branch
Gateway and BCM in other branches, is done via Session Manager, with CS 1000 benefitting from the
CS 1000 Adaptation in Session Manager and BCM/SRG benefitting from the Diversion Type adaptation in Session Manager.
Note:
B5800 Branch Gateway does not support Heritage-Nortel MCDN, hence site-to-site advanced functionality that depends on MCDN is not available in new B5800 Branch Gateways.
The B5800 Branch Gateway and the CS 1000 can be managed by System Manager. BCM will continue to be managed by Business Element Manager (BEM) and Network Control Manager (NCM).
Voicemail options for B5800 Branch Gateway distributed users are:
• local Embedded Voicemail or Standalone Voice Mail
• central Avaya Aura Messaging
• central CallPilot via CS 1000
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 33
CS 1000 and B5800 Branch Gateway deployments
Note:
The CallPilot number must be configured as the central voicemail system in the B5800 Branch
Gateway voicemail configuration. B5800 Branch Gateway does not support sending calls to
CallPilot based on configuring Call Forwarding for individual users.
For more information about voicemail options, see
Voicemail options on page 173.
Option 1
In this option, CS 1000 and B5800 Branch Gateway reside as peers and the SSG must be reassigned to support Session Manager.
34 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Option 2
Option 2
In this option, CS 1000 and B5800 Branch Gateway reside as peers and an additional SSG is required to support Session Manager.
Configuration considerations
The following guidelines must be considered when configuring B5800 Branch Gateways in CS
1000 deployments.
• To enable CS 1000 and Session Manager to use TLS for secure communication, security certificates must be exchanged between the two systems. See
• CallPilot can be configured as the central voicemail system. B5800 Branch Gateway does not access the CallPilot system over the PSTN when the Session Manager line is down.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 35
CS 1000 and B5800 Branch Gateway deployments
See Configuring B5800 Branch Gateway to use CallPilot for voicemail on page 179 for
more information.
• CallPilot supports the feature to send all calls unconditionally to voicemail. To configure this feature, in the Manager application, select User > Forwarding tab. Then complete the fields as appropriate. See the Manager on-line help for more information.
• CS 1000 and CallPilot can be configured to send a SIP NOTIFY message to the B5800
Branch Gateway user when a new message has arrived. For more information, see
Configuring CallPilot and CS 1000 to send MWI in a SIP NOTIFY message to the user on
page 181.
• If a B5800 Branch Gateway user has a CallPilot mailbox, when configuring the Session
Manager line, the default setting (RFC2833) should be used for in-band DTMF support.
See Step 9 in Adding an Avaya Aura Session Manager line
on page 146.
Since the B5800 Branch Gateway H.323 phone can only signal DTMF out of band, this means that for calls between a B5800 Branch Gateway H.323 phone and any destination that is signaled over the Session Manager line, the resulting media will be setup through the B5800 Branch Gateway RTP relay as opposed to bypassing the B5800 Branch
Gateway and flowing directly between the H.323 phone and the RTP endpoint/gateway/ application on the other side. (This is true even if Allow Direct Media Path is set on the
B5800 Branch Gateway Session Manager line).
• If the user will call into the Meeting Exchange conferencing server, when configuring the
Session Manager line, select either RFC2833 or Inband for DTMF support. Meeting
Exchange does not support digit exchange through out-of band (that is, Info) signaling.
See Step 9 in Adding an Avaya Aura Session Manager line
on page 146.
• There is limited fax interoperability between B5800 Branch Gateway and BCM or SRG.
Incoming faxes from BCM or SRG users to the B5800 Branch Gateway fax users cannot be completed due to signalling incompatibility. The fax machine on the B5800 Branch
Gateway should be configured as standard, rather than fax in order to ensure maximum interoperability. This is configured in the Manager application on the Analog Extension
> Analog tab > Equipment Classification.
• Delayed media setup through slow-start signalling on the CS 1000 is not supported on the B5800 Branch Gateway. (Current known impact is on scenarios which have a B5800
Branch Gateway user which is provisioning to CFNA and needs to send a RE_INVITE).
See the following application notes for additional information about B5800 Branch Gateways in CS 1000 deployments:
• Configuring a SIP Trunk between Avaya Aura Session Manager Release 6.1 and Avaya
Communication Server 1000E 7.5 — Issue 1.0.
• Configuring Secure SIP Connectivity using Transport Layer Security (TLS) between
Avaya Aura ® Session Manager R6.1 and Avaya Communication Server 1000E R7.5 with
Unified Communications Management on Avaya Aura System Manager R6.1, Issue 1.0
36 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Chapter 3: Planning
Before you begin installing and configuring the B5800 Branch Gateway system, you should already have determined the implementation issues listed in the table below.
You have determined...
See
The deployment option (option 1 or option 2) you are using.
CS 1000 and B5800 Branch Gateway deployments on page 33
The dial plan you are configuring for the system and each branch.
Dial plan considerations on page 38
The B5800 Branch Gateway licenses required for this installation.
How you are going to route outgoing
PSTN calls.
Branch PSTN call routing considerations on
page 40
Voicemail considerations on page 39
The voicemail solution you are going to deploy.
VoIP requirements.
Network assessment for VoIP requirements
on page 41
Unified Communications Management
(UCM) has been integrated with System
Manager.
Unified Communications Management and
on page 42
Prerequisites
The following applications and servers must be installed and configured before the B5800
Branch Gateway system is installed.
• If you are going to connect the B5800 Branch Gateway to an enterprise over the WAN,
Avaya Aura
®
Session Manager R6.1 or R6.2 must be installed and configured at the headquarters location.
• If you are going to centrally manage the B5800 Branch Gateways, Avaya Aura
®
System
Manager R6.2 must be installed and configured at the headquarters location.
• If you are going to use centralized licensing by WebLM, an Avaya Aura
®
System Manager
WebLM server or a standalone WebLM server must be installed and configured. The
WebLM server can be located at the headquarters location or anywhere in the network as long as the B5800 Branch Gateways can access it on the network.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 37
Planning
• Avaya Communication Server 1000 R7.5 with SIP Line Gateway must be installed and configured at the headquarters location.
• A stand-alone Secure Access Link (SAL) Gateway R2.1 must be deployed.
Note:
SAL Gateway does not support alarming for B5800 Branch Gateway managed devices in CS 1000 deployments.
Note:
System Platform's virtual SAL gateway is not supported.
Dial plan considerations
A uniform dial plan greatly simplifies configuration, management and phone calls within the network branch sites. For example, if each branch has similar roles such as reception, manager and warehouse - using the same extension number for each role and a unique prefix for each branch allows calls between sites with little need for directory lookups. It also means a standard configuration can be used at branches; simplifying installation, user training and maintenance.
For our examples we have used the following dial plan for each branch site:
• 3-digit branch prefixes beginning with 8 — A 3-digit branch prefix in the range 800 to
899. This allows us up to 100 branches yet keeps call routing simple. Any dialing at a branch that being with an 8 can be assumed to be a call to a branch number and can be routed to the Avaya Aura
®
Session Manager for routing to the correct branch.
• 3-digit extension numbers beginning with 2 — 3-digit extension numbers for all native extensions and hunt groups starting from 200. This is the default numbering used by
B5800 Branch Gateway.
Dial plan example
To describe a dial plan example, we have created Acme Travel, a travel agency with a growing number of branches. Each branch follows the same pattern, with extensions for a branch manager and a small team of travel consultants in a sales group.
Given the nature of the business, branch users need to make national and international calls.
The company has taken advantage of a bulk call contracts from it headquarters site so wants
38 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Voicemail considerations such calls routed via the headquarters site wherever possible. In addition, the branch staff want to keep their branch phone numbers.
• 3-digit branch numbers beginning with 8, ie. 800 to 899.
• 3-digit native extension numbers beginning with 2, ie. 200 to 299.
• Dial 9 prefix for outgoing PSTN calls.
• National and international calls allowed but routed via the headquarters site's PSTN trunks.
• Where a national call matches a branch location, it should be routed to the PSTN via that branch.
• Local calls allowed from each branch using its own PSTN trunks.
• CallPilot at the headquarters site provides voicemail services to all employees.
• The LAN on each branch has a unique IP address, 192.168.42.1, 192.168.44.1 and so on.
• National calls are made via the branch's PSTN trunks when the branch data connection to the headquarters site is not available or at maximum capacity.
This example assumes that all the branches were initially setup with the default North American locale. For B5800 Branch Gateway that means that a dial 9 prefix is used for external calls.
For calls in other locales or between branches in different locals, the example will need to be adjusted to ensure that the resulting number received at the remote branch will be routed to an external PSTN trunk and is suitable for external dialing.
Voicemail considerations
The B5800 Branch Gateway system uses its Embedded Voicemail by default. However, a number of other voicemail options are supported.
• Embedded Voicemail — Embedded Voicemail uses the system SD card in the B5800
Branch Gateway system control unit for storage of prompts and messages. Embedded
Voicemail supports mailboxes for all local extension numbers, announcements to waiting callers, and auto attendants (up to 40) for external calls. Its capacity is limited to 15 hours of recorded messages, prompts and announcements. Embedded Messaging Port licenses must be purchased with sufficient quantity to support the configured number of ports.
• Standalone Voice Mail — Standalone Voice Mail provides additional port capacity provided on a Linux server. You must have a Linux server installed to use this option.
When you select this option, you must enter the IP address of the Linux server where
Standalone Voice Mail is installed. This option provides a maximum capacity of 40 ports while the Embedded Voicemail option provides a maximum capacity of 6 ports.
Embedded Messaging Port licenses must be purchased with sufficient quantity to support the configured number of ports.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 39
Planning
• Avaya Aura Messaging — The B5800 Branch Gateway system can be configured to use Avaya Aura Messaging as its voicemail server when Session Manager is used as the
core SIP router. See Configuring B5800 Branch Gateway to use Avaya Aura Messaging for voicemail
on page 177 for more information. When Avaya Aura Messaging is used as the central voicemail system, at each branch you have the option to still use the local
Embedded Voicemail or Standalone Voice Mail for auto attendant operation and for announcements to waiting calls. Note that for this configuration, Embedded Voicemail licenses are required.
• CallPilot — The B5800 Branch Gateway system can be configured to use CallPilot as its voicemail server when Session Manager is used as the core SIP router. See
Configuring B5800 Branch Gateway to use CallPilot for voicemail on page 179 for more
information. When CallPilot is used as the central voicemail system, at each branch you have the option to still use the local Embedded Voicemail or Standalone Voice Mail for auto attendant operation and for announcements to waiting calls. Note that for this configuration, Embedded Voicemail licenses are required.
For more information about licensing, see Licensing on page 16.
The Park and Page feature is supported when the system voicemail type is configured as
Embedded Voicemail or Standalone Voice Mail. Park and Page is also supported on systems where Avaya Aura Messaging or CallPilot is configured as the central voicemail system and the local Embedded Voicemail provides auto attendant operation. The Park and Page feature allows a call to be parked while a page is made to a hunt group or extension. See
on page 174 for more information.
Branch PSTN call routing considerations
Each B5800 Branch Gateway system can support its own external PSTN trunks. When deployed in an Avaya Aura ® network, you have considerable flexibility over where outgoing
PSTN calls should emerge from the network and similarly where incoming calls should be routed.
For examples of some of the options available, see
Branch PSTN call routing examples
on page 291. The examples demonstrate the following options:
•
Centralized call control on page 291 — External calls at a branch site can be rerouted to
be dialed out at another site. This can be done for reasons of call cost and call control.
For example, the central site may have a bulk call tariff for national and international calls that would benefit all branches.
•
on page 294 — Having configured the branch to send outgoing external calls to the Avaya Aura ® Session Manager for onward routing, there may be
40 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Network assessment for VoIP requirements cases where a specific number should still be routed via the branches own PSTN trunks.
•
on page 296 — The B5800 Branch Gateway can be configured to allow some calls that would normally use the Avaya Aura ® Session Manager line to be routed via the PSTN when the Avaya Aura ® Session Manager line is not available.
The various methods used in the these examples can be combined to match the customer's needs. However the main aim should be as follows:
• To keep the branch configuration as generic as possible, i.e. to use the same PSTN call control in all branch configurations. This simplifies maintenance of multiple branches.
• To centralize as much of the PSTN call control in the Avaya Aura ® Session Manager as possible. Again this simplifies maintenance and control.
Network assessment for VoIP requirements
B5800 Branch Gateway is a converged telephony system, that is, it combines aspects of traditional PABX telephone systems and IP data and telephony systems. This works at various levels.
• Individual phone users can control the operation of their phone through applications running on their PC.
• Data traffic can be routed from the LAN interface to a telephony trunk interface, for example a dial-up ISP connection.
• Voice traffic can be routed across internal and external data links. This option is referred to as voice over IP (VoIP).
The VoIP mode of operation can include IP trunks between customer systems and/or SIP telephones for users. In either case the following factors must be considered:
• The B5800 Branch Gateway control unit must be fitted with voice compression channels.
These channels are used whenever an IP device (trunk or extension) needs to communicate with a non-IP device (trunk or extension) or a device that uses a different codec.
• A network assessment is a mandatory requirement for all systems using VoIP. For support issues with VoIP, Avaya may request access to the network assessment results and may refuse support if those are not available or satisfactory.
A network assessment includes a determination of the following:
• A network audit to review existing equipment and evaluate its capabilities, including its ability to meet both current and planned voice and data needs.
• A determination of network objectives, including the dominant traffic type, choice of technologies, and setting voice quality objectives.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 41
Planning
• The assessment should leave you confident that the implemented network will have the capacity for the foreseen data and voice traffic, and can support SIP, DHCP, TFTP and jitter buffers in SIP applications.
• An outline of the expected network assessment targets is:
Test
Latency
Packet Loss
Duration
Minimum Assessment Target
Less than 150ms
Less than 3%
Monitor statistics once every minute for a full week
Unified Communications Management and System Manager integration
Unified Communications Management (UCM) is the web administration tool used to manage
CS 1000 systems. For CS 1000 and B5800 Branch Gateway deployments, once Avaya Aura
Session Manager is deployed as part of the CS 1000 core, UCM must be integrated with
System Manager in order for users to be managed centrally through System Manager.
For existing UCM installations, integration with System Manager is supported only on standalone systems where UCM is not co-resident on the same server with other applications such as CS 1000 Call Server or Signaling Server.
For more information see “Appendix A: Migration to System Manager” in Unified
Communications Manager, Common Services Fundamentals, Avaya Communication Server
1000, Release 7.5, document number NN43001-116.
42 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Chapter 4: Installation requirements
This chapter provides information about power supplies, cables, grounding and environmental and space requirements for installing the B5800 Branch Gateway control unit and external expansion modules. The
B5800 Branch Gateway control unit can be mounted on the wall if no external expansion units are included in the installation. If the installation includes external expansion modules, the control unit and external expansion modules can be mounted into a standard 19-inch rack system.
Power supply backup (UPS)
The use of an Uninterrupted Power Supply (UPS) with any telephone system is strongly recommended. Even at sites that rarely lose electrical power, that power may occasionally have to be switched off for maintenance of other equipment. In addition, most UPSs also provide an element of power conditioning, reducing spikes and surges.
The capacity of UPS systems and the total equipment load the UPS is expected to support are usually quoted in VA. Where equipment load is quoted in Watts, multiply by 1.4 to get the VA load.
The calculation of how much UPS capacity is required depends on several choices.
• What equipment to place on the UPS? Remember to include server PCs such as the voicemail. It is recommended that the total load on a new UPS is never greater than 75% capacity, thus allowing for future equipment.
• How many minutes of UPS support is required? Actual UPS runtime is variable, it depends on what percentage of the UPSs capacity the total equipment load represents.
For example, a 1000VA capacity UPS may only support a 1000VA (100%) load for 5 minutes. This relationship is not linear, the same UPS would support a 500VA (50%) load for 16 minutes. Therefore the lower the percentage of capacity used, the increasingly longer the UPS runtime, typically up to 8 hours maximum. Remember also that for most
UPS's the ratio of discharge to full recharge time is 1:10.
• How many output sockets does the UPS provide? Multiple UPS units may be required to ensure that every item of supported equipment has its own supply socket.
The web site http://www.avayaups.com
provides a calculator into which you can enter the equipment you want supported on a UPS. It will then display various UPS options. The site uses VA values for typical B5800 Branch Gateway systems. However, if more specific values are required for a particular system, the table below can be used to enter values.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 43
Installation requirements
Typical B5800 Branch Gateway System
B5800 Branch Gateway system
Individual Equipment
Analog 16 module
Digital Station 16 module
Digital Station 30 module
WAN3 module
So8 module
230
VA
88
34
42
17
34
VA
The 1151D2 power supply unit for Avaya H.323 IP phones includes a backup battery. This typically provides 15 minutes backup at maximum load (20 Watts) and up to 8 hours at light load (2 Watts).
Cables
The B5800 Branch Gateway system is designed primarily for use within an RJ45 structured cabling system using CAT3 unshielded twisted-pair (UTP) cabling and RJ45 sockets.
A structured cabling system is one where cables are run from a central RJ45 patch panel in the communications/data room to individual RJ45 sockets at user locations. All wires in each cable between the patch panel and the desk socket are connected straight through. This arrangement allows devices connected at the patch panel to be swapped to match the type of device that needs to be connected at the user socket. For example, making one user socket a phone port and another user socket a computer LAN port, without requiring any rewiring of the cables between the patch panel and the user location.
• Traditional IDC punchdown wiring installations — Where necessary, the far end RJ45 plug can be stripped from B5800 Branch Gateway cables and wired into traditional wiring
44 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Cables systems using punch-block connectors. This type of installation should be performed by an experienced wiring technician.
• Trunk connections — The majority of B5800 Branch Gateway trunk ports use RJ45 connectors for acceptance of an RJ45-to-RJ45 cable. However, connection at the line provider's end may require use of a different plug type in order to match the line providers equipment.
• RJ11 phone connectors — Many phones use RJ11 sockets and are supplied with RJ11to-RJ11 cables. RJ11 plugs can be inserted into RJ45 sockets and in many case the connection will work. However this is not recommended or supported as the connection lock is not truly positive and may become disconnected. An RJ45-to-RJ11 cable is available for these connections.
Standard B5800 Branch Gateway cables
The following are Avaya standard cables available for use with B5800 Branch Gateway systems. The maximum length is applicable if the standard Avaya cable is replaced with an alternate cable.
Maximum
Length
2m/6'6''
Cable
V.35 WAN cable
X.21 WAN cable
Description Standard
Length
2m/6'6'' 9-way DTE cable
Structured cabling
DS line cable
BRI/PRI trunk cable Connects BRI/PRI trunk ports to the line provider's network termination point. RJ45 to RJ45. Red.
Expansion interconnect cable
Connects from RJ45 sockets to RJ11 socketed DS and analog phones.
4m/13'2''
3m/9'10''
LAN cable
Connects the control unit to expansion modules (except WAN3 modules).
RJ45 to RJ45. Blue.
1m/3'3''
Connects from B5800 Branch
Gateway LAN ports toB5800 Branch
Gateway devices. RJ45 to RJ45.
Grey.
3m/9'10''
V.24 WAN cable
Connects to control unit RS232 DTE port. 9-way D-type plug to 9-way Dtype socket.
37-way D-type plug to 25-way D-type plug.
3m/9'10''
37-way D-type plug to 34-way MRAC plug.
3m/9'10''
37-way D-type plug to 15-way D-type plug.
3m/9'10''
–
–
1m/3'3''
100m/328'
5m/16'5''
5m/16'5''
5m/16'5''
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 45
Installation requirements
Grounding
Use of ground connections reduces the likelihood of problems in most telephony and data systems. This is especially important in buildings where multiple items of equipment are interconnected using long cable runs, for example phone and data networks.
All control units and external expansion modules must be connected to a functional ground.
Where the unit is connected to a power outlet using a power cord with an earth lead, the power outlet must be connected to a protective earth.
In some cases, such as ground start trunks, in addition to being a protective measure this is a functional requirement for the equipment to operate. In other cases it may be a locale regulatory requirement and or a necessary protective step, for example areas of high lightning risk.
For more information about grounding including the location of the ground points on the control
unit and external expansion modules, see Grounding
on page 73.
Wall and rack mounting
The B5800 Branch Gateway control unit is designed to be freestanding. When external expansion modules are used, the control unit and expansion modules are intended to be
Rack mounting on page 69 for more information.
Voice compression channels
Calls to and from IP devices can require conversion to the audio codec format being used by the IP device. For B5800 Branch Gateway systems this conversion is done by voice compression channels. These support the common IP audio codecs G711, G723 and
G729a.
For the B5800 Branch Gateway control unit, channels can be added using VCM base cards,
BRI combination cards, and ATM combination cards. See
on page 20 for more information about these cards.
The voice compression channels are used as follows:
46 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Voice compression channels
Call type
IP device to non-IP device
IP device to IP device
Voice compression channel usage
These calls require a voice compression channel for the duration of the call. If no channel is available, busy indication is returned to the caller.
Call progress tones (for example dial tone, secondary dial tone, etc) do not require voice compression channels with the following exceptions:
• Short code confirmation, ARS camp on and account code entry tones require a voice compression channel.
• Devices using G723 require a voice compression channel for all tones except call waiting.
When a call is connected:
• If the IP devices use the same audio codec no voice compression channel is used.
• If the devices use differing audio codecs, a voice compression channel is required for each.
Non-IP device to non-IP device
Music on Hold
Voicemail services and IP devices
No voice compression channels are required.
Conference resources and IP devices
Conferencing resources are managed by the conference chip which is on the B5800 Branch Gateway TDM bus.
Therefore, a voice compression channel is required for each
IP device involved in a conference. This includes services that use conference resources such as call listen, intrusion, call recording and silent monitoring.
Page calls to IP dDevice
This is provided from the B5800 Branch Gateway TDM bus and therefore requires a voice compression channel when played to an IP device.
B5800 Branch Gateway only uses G729a for page calls, therefore only requiring one channel but also only supporting pages to G729a capable devices.
Calls to the B5800 Branch Gateway voicemail servers are treated as data calls from the TDM bus. Therefore calls from an IP device to voicemail require a voice compression channel.
T38 fax calls In order to use T38 fax connection, B5800 Branch Gateway performs fax tone detection if the analog extension connected to the fax machine is set as “Standard telephone.” If the fax machine does not include an attached handset that is used to make/receive voice calls, then the
Equipment Classification of an analog extension connected to the fax machine can be set to Fax Machine, which will result in T38 fax connection without fax tone detection and respective signaling renegotiation. Additionally, a new short code feature, Dial Fax, is available.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 47
Installation requirements
Measuring channel usage
The IP Office System Status Application can be used to display voice compression channel usage. Within the Resources section it displays the number of channels in use. It also displays how often there have been insufficient channels available and the last time such an event occurred.
For the VCM cards, the level of channel usage is also indicated by the LEDs (1 to 8) on the front of the VCM card.
Emergency and power failure ports
B5800 Branch Gateway systems can provide 2 types of analog extension power failure ports as described in the following table.
Type
Switching power failure ports
Emergency only power failure ports
Description
During normal B5800 Branch
Gateway operation these ports can be used for normal analog phone connection.
During power failure the port is directly connected to an analog trunk port.
Provided By:
• Analog phone 8 card
When an analog phone 8 base card is fitted with an analog trunk daughter card, during power failure extension port 8 is connected to analog trunk port 12.
• ATM combination card
On this card, during power failure, extension port 8 is connected to analog trunk port 12.
During normal B5800 Branch
Gateway operation these ports cannot be used.
During power failure the port is directly connected to an analog trunk port.
• Analog trunk daughter card
Regardless of the card hosting it, during power failure pins 4 and 5 of port 12 are connected to pins 7 and
8.
In all cases these only work with loop-start analog trunks. Any phones connected to these ports should be clearly labeled as power fail extensions in accordance with the appropriate national and local regulatory requirements.
48 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Environmental requirements
Environmental requirements
The planned location must meet the following requirements. If being installed into a rack system, these are requirements for within the rack:
• Temperature: 0°C to 40°C / 32°F to 104°F.
• Humidity: 10% to 95% non-condensing.
• Check there are no flammable materials in the area.
• Check there is no possibility of flooding.
• Check that no other machinery or equipment needs to be moved first.
• Check that it is not an excessively dusty atmosphere.
• Check that the area is unlikely to suffer rapid changes in temperature and humidity.
• Check for the proximity of strong magnetic fields, sources of radio frequency and other electrical interference.
• Check there are no corrosive chemicals or gasses.
• Check there is no excessive vibration or potential of excessive vibration, especially of any mounting surface.
• Check that where telephones are installed in another building, that the appropriate protectors and protective grounds are fitted (see
Out of Building Telephone Installation
on page 74).
• Check there is suitable lighting for installation, system programming and future maintenance.
• Check that there is sufficient working space for installation and future maintenance.
• Ensure that likely activities near the system will not cause any problems, e.g. access to and maintenance of any other equipment in the area.
• Where ventilation holes are present on any of the B5800 Branch Gateway units, those holes should not be covered or blocked.
• The surface must be flat horizontal for free-standing or rack mounted installations.
Wall mounting: In additional to the requirements above, the following are applicable to control units that are mounted on the wall.
• Units must only be mounted onto permanent wall surfaces.
• The surface must be vertical and flat.
• Orientation of the unit must be as shown in the section on IP500 Wall Mounting on
page 67.
• The appropriate Avaya wall mounting kits must be used.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 49
Installation requirements
Note:
See
Important safety instructions when using your telephone equipment on page 265 for
basic safety precautions to follow when using your telephone equipment.
Space requirements
The B5800 Branch Gateway control unit and external expansion modules are designed to be installed either in a free-standing stack or into a 19-inch rack system. Rack installation requires a rack mounting kit for each control unit and expansion module. See
page 69 for more information. If there are no external expansion modules used in the installation, the control unit can be wall mounted using a wall mounting kit. See
Wall mounting on page 67 for more information.
• Cable clearance
Clearance must be provided at the front and rear of all modules for cable access. Allow a minimum clearance of 90mm (3.5 inches).
• Additional clearance
Care should be taken to ensure that the positioning of the modules does not interrupt air flow and other environmental requirements. The control unit has ventilation slots at the
side that must not be blocked. See Environmental requirements
on page 49 and Rack space requirements
on page 52 for more information.
• Cable access
Power cords must not be attached to the building surface or run through walls, ceilings, floors and similar openings. Installation measures must be taken to prevent physical damage to the power supply cord, including proper routing of the power supply cord and provision of a socket outlet near the fixed equipment or positioning of the equipment near a socket outlet.
Control unit
When wall mounted, a clearance of 500mm is required on all sides. The ventilation slots on the rear and sides should not be covered or blocked.
50 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Space requirements
External expansion modules
The dimensions below are applicable to all external expansion modules.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 51
Installation requirements
Wall mounting space requirements
The control unit can be wall mounted if not using any external expansion modules. A wall mounting kit is required in addition to 4.5mm fixings suitable for the wall type. A clearance of
500mm around the control unit is required. See
on page 67 for more information.
Rack space requirements
The B5800 Branch Gateway control unit and external expansion modules can be rack mounted into standard 19-inch rack systems. Each unit requires a 2U slot space within the rack. Rack mounting requires a rack mounting kit for each control unit and external expansion module.
See
on page 69 for more information about the rack mounting kit.
Where B5800 Branch Gateway systems are being rack mounted, the effect of conditions within the rack cabinet must be considered. For example the rack temperature may be above the room temperature and airflow within the rack will be restricted. The environmental requirements for the individual control unit and expansion modules are still applicable inside the rack cabinet.
Barrier box rack mounting kit
The barrier box rack mounting kit must be used for out-of-building analog phone extensions.
This bracket allows up to 8 barrier boxes to be rack mounted and simplifies the number of connections to the protective ground point in the rack. This kit must be used when more than
3 barrier boxes are in use and supports a maximum of 16 barrier boxes for a single external expansion module.
52 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Space requirements
Rack module positioning
The integral expansion ports on a control unit are located on the rear of the unit. An additional
4 expansion ports can be added to the front of the control unit by installing a 4-port expansion card.
• Each external expansion module is supplied with a blue 1 meter (3'3'') expansion interconnect cable. This cable must be used when connecting to expansion ports on the rear of a control unit.
• When connecting to expansion ports on a 4-port expansion card, a yellow 2-meter (6'6") expansion interconnect cable can be used in place of the standard blue cable. Four yellow cables are supplied with the 4-port expansion card.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 53
Installation requirements
54 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Chapter 5: Hardware and software installation
All hardware components should be turned off while they are installed and connected. Once the installation is complete, the system is turned on. The control unit will then upgrade all of the connected components, including phones, to the appropriate level of firmware. In addition, when the system is turned on, it should not be connected to the customer's data network. This ensures that the control unit will default to known default IP address settings (unless you have pre-loaded the System SD card with a configuration file with different settings).
B5800 Branch Gateway R6.2 provides the B5800 Branch Gateway Initial Installation utility. This utility provides a default configuration and security settings that minimize initial installation activities and maximize security. The system must be configured with the default settings before the system can be administered by Avaya Aura ® System Manager. For more information, see
Using the Initial Installation
on page 121.
Installation checklist
Use this checklist to monitor your progress as you install a B5800 Branch Gateway system.
# Description Section
1 Review the prerequisites.
2 Review the Installation requirements.
Installation requirements on page 43.
3 Review the required tools and equipment.
4 Unpack the equipment.
page 56.
on page 57.
5 If you want to pre-configure the system, there are several tasks you can perform to configure the
SD card before it is installed in the control unit.
on page 58.
6 Prepare the base and trunk cards and install them in the control unit.
See Base and trunk card installation
on page 61.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 55
Hardware and software installation
# Description Section
7 Do one of the following:
• Install the control unit on the wall.
• Install the control unit in a rack.
See one of the following:
•
•
on page 69.
8 Connect the external expansion modules.
9 Connect the control unit and external expansion modules to a functional ground.
page 71.
on page 73.
10 Install the B5800 Branch Gateway administration applications on the installer PC.
See Installing the administration applications on page 81.
on page 81.
11 Connect the PC to the control unit.
12 Apply power to the system.
See Applying power to the system
page 83.
on
13 Use the Initial Installation Utility to configure a default configuration and security settings.
See Using the Initial Installation Utility
on page 121.
15 Connect the control unit to the network.
18 Connect the phones.
Connecting the control unit to the network on page 88.
on page 89.
Tools and equipment required
Following is a general summary of the tools required. Additional tools and equipment are required for wall and/or rack mounting and to fashion ground cable connections suitable to local requirements.
• Tools required
- 5mm Flat-blade screwdriver
- Crosshead screwdriver
- Anti-static wrist strap and ground point
- RJ45-RJ45 ethernet LAN cable
- M4 cross-head screwdriver
- Tools suitable for crimping a cable spade
56 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Unpacking equipment
- If wall mounting, drills and tools for wall mounting fixtures
• Additional parts required
In addition to orderable system equipment, the following items are required.
- 14AWG solid copper wire for ground connection of control units and expansion modules
- Cable sleeve matching local regulator requirements for ground wires. Typically green for a functional ground and green/yellow for a protective ground.
- If wall mounting, additional 4.5mm diameter fixtures and fittings suitable for the wall type
- Cable ties and labels for tidying and identifying cables
• PC requirements
- Windows PC with the administration software installed. See PC requirements
on page 80.
- SD card reader
Unpacking equipment
About this task
Use the following procedure when unpacking any equipment supplied by Avaya or an Avaya reseller or distributor. Have the equipment order checklist available as you unpack the equipment to ensure you have all parts and equipment ordered.
Procedure
1. Check for package damage
Before unpacking any equipment, check for any signs of damage that may have occurred during transit. If any damage exists bring it to the attention of the carrier.
2. Check the correct parts have been delivered
Check all cartons against the packing slip and ensure that you have the correct items. Report any errors or omissions to the equipment supplier.
3. Retain all packaging and documentation
While unpacking the equipment, retain all the packaging material. Fault returns are accepted only if repackaged in the original packaging. If performing a staged installation, the original packaging will also assist when repacking equipment to be moved to the final install site.
4. Ensure that anti-static protection measures areobserved
Ensure that anti-static protection measures are observed at all times when handling equipment with exposed electrical circuit boards.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 57
Hardware and software installation
5. Check all parts
Visually inspect each item and check that all the necessary documentation and accessory items have been included. Report any errors or omissions to the dealer who supplied the equipment.
6. Check all documentation
Ensure that you read and retain any documentation included with the equipment.
SD card preparation
B5800 Branch Gateway control units are supplied with no installed firmware or configuration.
When first powered up, the control unit loads and installs the necessary firmware from the
B5800 Branch Gateway System SD card that has been installed in the control unit. A default configuration is then created that matches the cards installed in the control unit and external expansion modules attached.
You can perform the following tasks prior to installing the B5800 Branch Gateway System SD card in order to pre-configure the system.
• See Upgrade the Card Firmware on page 58
• See Creating a configuration file
on page 59.
• See Adding a configuration file
on page 60.
• See Adding music-on-hold files on page 60.
For more information about SD cards, see
SD Card Management on page 243.
Upgrading the card firmware
About this task
This process creates the folder structure on the SD card and copies the firmware files from those installed with Manager onto the SD card. This includes the binary files for the B5800
Branch Gateway system and any external expansion modules and phones. It also includes the prompt files for embedded voicemail operation.
This process can be used to upgrade an existing SD card to match the file set installed with
Manager. The card installed in the System SD slot must be an Avaya SD Feature Key card.
The card must be correctly formatted.
If the card contains any dynamic system files, for example SMDR records, they are temporarily backed up by Manager and then restored after the card is recreated.
58 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
SD card preparation
Procedure
1. Insert the SD card into a card reader on the Manager PC.
Note:
Do not remove the SD card. Removing the SD card will interrupt the upgrade.
2. Using Manager, select File > Advanced > Recreate IP Office SD Card.
3. Select Avaya Branch Gateway.
4. Browse to the card location and click OK.
Manager starts creating folders on the SD card and copying the required files into those folders. This process takes approximately 15 minutes. Do not remove the SD card until Manager shows a message that the recreation has finished.
Creating a configuration file
About this task
Manager can be used to create a new configuration file without connecting to a B5800 Branch
Gateway system. This allows the creation of a configuration prior to installing the system. The configuration file can be loaded on the System SD card before the card is installed. The configuration file specifies the system's location, trunk cards, control unit, and expansion modules.
• The configuration created must match the physical equipment in the B5800 Branch
Gateway system for which the configuration will be loaded. If they do not match, the system may reset and experience other problems.
• The configuration creation tool includes all control units, external expansion modules and trunk cards supported by B5800 Branch Gateway. It is your responsibility to confirm the
B5800 Branch Gateway equipment that is supported in your location.
Procedure
1. Start Manager with no configuration loaded into Manager.
2. Click on Create an Offline Configuration in the simplified view.
3. Select the type of configuration that you want to create.
4. When completed, click OK.
Manager will create and load the configuration.
5. Edit the configuration to match the customer requirements.
This can include importing information from prepared CSV files.
Note:
For information about CSV files, see the Help available in the Manager application. From Manager, select Help > Contents. In the Manager Help
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 59
Hardware and software installation window, in the left navigation pane, expand IP Office Configuration Mode and then expand Editing Configuration Settings. Then click Importing and
Exporting Settings.
6. When completed, select File > Save Configuration As.
Adding a configuration file
About this task
Use this procedure to add a configuration file on the System SD card. That configuration file will then be used when the B5800 Branch Gateway system is started.
Procedure
1. Create an offline configuration that matches the customer requirements and the equipment that will be installed in the B5800 Branch Gateway system. See
on page 59.
2. Rename the configuration file config.cfg.
3. Using a card reader, copy the file into the /system/primary folder on the System
SD memory card.
Adding music-on-hold files
About this task
By default B5800 Branch Gateway uses internal music-on-hold by uploading a music file. You can load a file onto the System SD card prior to installing it in the control unit
The file must be of the following format and must be called holdmusic.wav.
Property
File Type
Bit Rate
Audio sample size
Channels
Audio Sample Rate
Audio Format
Length
WAV
128kbps
16 bit
1 (mono)
8 kHz
PCM
Up to 90 seconds.
Value
60 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Base and trunk card installation
Procedure
1. Rename the music file holdmusic.wav.
2. Using a card reader, copy the file into the /system/primary folder on the System
SD memory card.
3. If the B5800 Branch Gateway system is configured for additional music-on-hold files
(up to 3 additional files), copy those files to the same location.
The name of the additional files must match those specified in the B5800 Branch
Gateway system configuration.
Base and trunk card installation
The base cards and trunk daughter cards should be fitted before power is applied to the control unit. Ensure that cards are inserted in the order that matches the planned or pre-built configuration. In general, the following applies to card installation:
• Cards can be fitted in any order into any available slots. The only exception is the 4-port expansion card which can only be installed in right-hand slot 4.
• It is recommended that cards are fitted from left to right.
• There are restrictions to the number of supported cards of some types. When a limit is exceed, the right-most card of that type will not function.
• Ensure that you use the labels supplied to identify the card fitted into the control unit.
Warning:
• Correct anti-static protection steps should be taken before handling circuit boards.
• Cards must never be added or removed from the control unit while it has power connected.
Trunk daughter card preparation
Trunk daughter cards can be fitted to any base card except the legacy card carrier. For combination cards, the trunk daughter card is pre-installed and cannot be changed.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 61
Hardware and software installation
Warning:
Correct anti-static protection steps should be taken while handling circuit boards.
Parts and equipment required
• Base card (except the legacy card carrier)
• Trunk daughter card
• 3 stand-off pillars (these are supplied with the trunk daughter card)
Tools required
• 5mm Flat-blade screwdriver
• Anti-static wrist strap and ground point
Installing a trunk daughter card
Procedure
1. Check that correct cards have been supplied.
62 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Base and trunk card installation
2. Ensure that you are wearing an anti-static wrist strap connected to a suitable ground point.
3. On the base card, identify the position of the 3 holes for the plastic pillars for the trunk daughter card.
These are along the same edge as the card connector.
4. Fit the stand-off pillars to the base card.
5. If there is a clip-on metal shield over the connector block on the base card, remove it.
6. Using minimal force and checking that the pins are correctly located, push the trunk card onto its connector block and the stand-off pillars.
7. Check that the card connector has snapped into position.
8. Using the washers and screws provided, secure the metal stand-off pillars to the base card.
9. From the set of labels that are supplied with the trunk daughter card, fit the appropriate label to the front of the base card.
Legacy carrier card preparation
A legacy carrier card can be used to fit VCM cards into the B5800 Branch Gateway control unit. Up to 2 legacy carrier cards can be inserted. The following trunk and VCM cards are supported. Cards not listed are not supported.
• PRI T1
• Dual PRI T1
• PRI 30 E1 (1.4)
• Dual PRI E1
• PRI 30 E1R2 RJ45
• Dual PRI E1R2 RJ45
• BRI-8 (UNI)
• ANLG 4 UNI (US only)
• VCM 4
• VCM 8
• VCM 16
• VCM 24
• VCM 30
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 63
Hardware and software installation
Warning:
Correct anti-static protection steps should be taken while handling circuit boards.
Parts and equipment required
• Legacy carrier card
• VCM card
• 2 plastic stand-off pillars per card
• Trunk cards are supplied with a replacement blanking plate which is not required.
Tools required
• 5mm Flat-blade screwdriver
• Anti-static wrist strap and ground point
64 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Base and trunk card installation
Installing a legacy carrier card
Procedure
1. Check that correct cards have been supplied.
2. Ensure that you are wearing an anti-static wrist strap connected to a suitable ground point.
3. On the carrier card identify the position of the jumper block and stand-off pillar holes for the IP400 card.
The peg holes are labeled as VCM or TRUNK.
4. If fitting an IP400 trunk card, identify which of the plastic snap-off panels on the front of the carrier card need to be removed to allow the trunk cable connections.
5. Carefully remove those panels.
6. Fit the stand-off pillars to the legacy carrier card.
7. Using minimal force and checking that the pins are correctly located, push the IP400 card onto its jumper and the stand-off pillars.
Base card insertion
Having prepared each base card by adding the trunk daughter cards or legacy carrier cards, the base card can be inserted into the control unit.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 65
Hardware and software installation
Warning:
• Correct anti-static protection steps should be taken before handling circuit boards.
• Cards must never be added or removed from the control unit while it has power connected.
• Tools required
• 5mm Flat-blade screwdriver
• Anti-static wrist strap and ground point
Installing a base card
Procedure
1. Check that there is no power to the control unit.
2. Using a flat-bladed screwdriver, remove the cover from the slot on the front of the control unit that will be used for each card being installed.
This cover is no longer required but should be retained until installation has been completed.
3. Allowing the card to rest against the bottom of the slot, begin sliding it into the control unit.
4. When half inserted, check that the card rails have engaged with the slot edges by trying to gently rotate it. If the card rotates, remove it and begin inserting it again.
The card should slide in freely until almost fully inserted.
66 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Wall mounting
5. At this point apply pressure at the base of the front of the card to complete insertion.
6. Using a flat-bladed screwdriver secure the card.
Wall mounting
B5800 Branch Gateway control units can be wall mounted. This requires a wall mounting kit plus additional 4.5mm fixtures and fittings suitable for the wall type. The wall mounting kit includes two brackets, one top and one bottom.
In addition to the existing
environmental requirements on page 49, the following requirements
apply when wall mounting a unit:
• The wall surface must be vertical, flat and vibration free.
• The brackets must be used as shown, with the deeper tray-like bracket used at the bottom of the wall mounted control unit.
• Only the screws (M3 x 6mm) provided with the mounting kit should be used to attach the brackets to the control unit.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 67
Hardware and software installation
68 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Rack mounting
Rack mounting
The B5800 Branch Gateway control unit and external expansion units can be rack mounted into 19-inch rack systems. This requires a rack mounting kit for each unit.
The rack mounting kit includes:
• A rack mounting bracket and screws for attachment of the bracket to the unit
• Nuts and bolts for rack attachment
• Brackets and cable ties for cable tidying
Environmental requirements
In addition to the
on page 49, the following factors must be considered when rack mounting a unit:
• Rack positioning — Ensure compliance with the rack manufacturers safety instructions.
For example check that the rack legs have been lowered and fixing brackets have been used to stop toppling.
• Elevated operating ambient — If installed in a closed or multi-unit rack assembly, the operating ambient temperature of the rack environment may be greater than room ambient. Therefore, consideration should be given to installing the equipment in an environment compatible with the maximum ambient temperature (Tma) specified by the manufacturer.
- Operating temperature: 0°C (32°F) to 40°C (104°F).
- Operating humidity: 10% to 95% non-condensing.
• Reduced air flow — Installation of the equipment in a rack should be such that the amount of air flow required for safe operation of the equipment is not compromised. Proper ventilation must be maintained. The side ventilation slots on the control unit should not be covered or blocked.
• Mechanical loading — Mounting of the equipment in the rack should be such that a hazardous condition is not achieved due to uneven mechanical loading.
• Circuit overloading — Consideration should be given to the connection of the equipment to the supply circuit and the effect that overloading of the circuits might have on overcurrent protection and supply wiring. Appropriate consideration of equipment nameplate ratings should be used when addressing this concern.
• Reliable earthing — Reliable earthing of rack-mounted equipment should be maintained.
Particular attention should be given to supply connections other than direct connections to the branch circuit (e.g. use of power strips).
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 69
Hardware and software installation
•
Important:
Only the screws (M3 x 6mm) provided with the mounting kit should used to attach the
70 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
External expansion modules brackets to the control unit. As indicated in the diagram, the rack mounting bracket can be used in several positions on the unit.
External expansion modules
External expansion modules should be connected to the control unit before power is applied to the control unit. Ensure that modules are attached in the order that matches the planned or pre-built configuration.
External expansion modules connect to the control unit using an expansion interconnect cable.
Each module is supplied with an expansion interconnect cable and a power supply unit. An appropriate local specific power cord for the power supply unit must be ordered separately.
• Each external expansion module is supplied with a blue 1 meter (3'3'') expansion interconnect cable. This cable must be used when connecting to expansion ports on the rear of a control unit.
• When connecting to expansion ports on a 4-port expansion card, a yellow 2-meter (6'6") expansion interconnect cable can be used in place of the standard blue cable. Four yellow cables are supplied with the 4-port expansion card.
Installation requirements
• Installation space either on or under the control unit
• Switched power outlet socket
• Available EXPANSION port on the control unit
• Functional grounding requirements — connection of a functional ground is:
- recommend for all modules
- mandatory for analog trunk modules
• Protective grounding requirements — connection of a protective ground via surge protection equipment is:
- mandatory for analog trunk modules in the Republic of South Africa
- mandatory for digital station and phone modules connected to out-of-building extensions
- mandatory for digital station V2 and phone V2 modules
Tools required
• Manager PC
• Tools for rack mounting (optional)
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 71
Hardware and software installation
Parts and equipment required
• External expansion module — each module is supplied with a suitable external power supply unit and a 1m blue interconnect cable. 2m yellow interconnect cables are supplied with the 4-Port expansion card and should only be used with that card.
• Power cord for the power supply unit
• Rack mounting kit (optional)
• Cable labeling tags
Connecting external expansion modules
About this task
Note:
External expansion modules should not be attached to a control unit that has power.
Procedure
1. If the system is being installed in a rack, attach the rack mounting kit to the
expansion module. See Rack mounting
on page 69.
2. Attach the external expansion module's power supply but do not switch power on.
3. Connect the expansion interconnect cable from the module's EXPANSION port to the EXPANSION port on the control unit. Make careful note of the port used and include this detail on the cable label and any other system records.
72 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Grounding
Grounding
Use of ground connections reduces the likelihood of problems in most telephony and data systems. This is especially important in buildings where multiple items of equipment are interconnected using long cable runs, for example phone and data networks.
All control units and external expansion modules must be connected to a functional ground.
Where the unit is connected to a power outlet using a power cord with an earth lead, the power outlet must be connected to a protective earth.
In some cases, such as ground start trunks, in addition to being a protective measure this is a functional requirement for the equipment to operate. In other cases it may be a locale regulatory requirement and or a necessary protective step, for example areas of high lightning risk.
Warning:
During installation do not assume that ground points are correctly connected to ground. Test ground points before relying on them to ground connected equipment.
Additional protective equipment
In addition to grounding, additional protective equipment is required in the following situations.
• On any digital station or phones external expansion module connected to an extension
located in another building. See Out of Building Telephone Installations on page 74.
• In the Republic of South Africa, on all analog trunk external expansion modules (ATM16) and on any control units containing an analog trunk cards (ATM4/ATM4U).
Tools required
• M4 cross-head screwdriver
• Tools suitable for crimping a cable spade
Parts and equipment required
• 14AWG solid copper wire for ground connection
• Cable sleeve matching local regulator requirements. Typically green for a functional ground and green/yellow for a protective ground.
The ground point on control units and expansion modules are marked with a or symbol.
Ground connections to these points should use a 14 AWG solid wire with either a green sleeve for a functional ground or green and yellow sleeve for a protective ground.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 73
Hardware and software installation
B5800 Branch Gateway control unit
On control units the ground point is located above the RS232 DTE port.
External expansion modules
On expansion modules, the ground point is a 4mm screw located towards the right on the rear of the module.
On some older modules, the dedicated ground point screw is not present. In those cases, the top-center cover fixing screw (3mm) can be used as an alternative ground connection point.
A toothed washer should be added to ensure good contact.
Out-of-building connections/lightning protection
The following are the only supported scenarios in which wired extensions and devices outside the main building can be connected to the B5800 Branch Gateway system. In these scenarios, additional protection in the form of protective grounding and surge protectors must be fitted.
Warning:
The fitting of additional protection does not remove the risk of damage. It merely reduces the chances of damage.
74 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Out-of-building connections/lightning protection
• Cables of different types, for example trunk lines, phone extensions, ground and power connections, should be kept separate.
• All cabling between buildings should be enclosed in grounded ducting. Ideally this ducting should be buried.
• A Primary Protection Box must be provided at the point where the cables enter the building. This should be three point protection (tip, ring and ground). Typically this would be gas tube protection provided by the local telephone company. The ground wire must be thick enough to handle all the lines being affected by indirect strike at the same time.
Connection type Protection device type
DS phone extensions
External expansion module
DS ports only.
ITWLinx towerMAX DS/2
Supports up to 4 connections.
(This device was previously referred to as the Avaya
146E.)
Analog phone extensions
Phones external expansion module (POT or Phone) ports only.
Analog trunks
Barrier box
Supports a single connection.
Maximum of 16 on any expansion module.
ITWLinx towerMAX CO/4x4
Supports up to 4 two-wire lines. (This device was previously referred to as the
Avaya 146C.)
Requirement
• Connection from the expansion module to the phone must be via a surge protector at each end and via the primary protection point in each building.
• The expansion module, control unit, and IROB devices must be connected to the protective ground point in their building.
• The between building connection must be via earthed ducting, preferable underground. The cable must not be exposed externally at any point.
For installations in the
Republic of South Africa, the fitting of surge protection on analog trunks is a requirement.
For other locations where the risk of lightning strikes is felt to be high, additional protection of incoming analog trunks is recommended.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 75
Hardware and software installation
Connection type
External output switch
Protection device type
ITWLinx towerMAX SCL/8
(This device was previously referred to as the Avaya
146G.)
Requirement
Connections from an Ext O/P port to an external relay device must be via a surge protector.
The towerMAX range of devices are supplied by ITWLinx ( http://www.itwlinx.com
).
DS phone IROB installation
When digital phone extensions are required in another building, additional In-Range Out-Of-
Building (IROB) protective equipment must be used. For phones connected to B5800 Branch
Gateway DS ports, the supported device supplied by ITWLinx is a towerMAX DS/2 module.
This IROB device was previously referred to by Avaya as the 146E IROB.
The protection device should be installed as per the instructions supplied with the device. The ground points on the control unit and the DS modules must be connected to a protective ground using 18AWG wire with a green and yellow sleeve.
Typically the IROBs 2 RJ45 EQUIPMENT ports are straight through connected to the 2 RJ45
LINE ports. This allows existing RJ45 structured cabling, using pins 4 and 5, to be used without rewiring for up to two DS connections. However each of these ports can be used to connect a second extension using pins 3 and 6.
LINE
1
2
3
4
5
6
7
8
Not used
Not used
Ring II
(Optional)
Ring I
Tip I
Tip II
(Optional)
Not used
Not used
Signal
76 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
4
5
6
7
8
2
3
1
EQUIPMENT
October 2012
Out-of-building connections/lightning protection
Analog phone barrier boxes
Where analog phone extensions are required in another building, phone barrier boxes and protective earth connections must be used .
Warning:
PHONE (POT) ports on the front of control units must not be used for extensions that are external to the main building.
• The correct B5800 Branch Gateway barrier boxes must be used. These modules have been designed specifically for the signalling voltages used by the B5800 Branch Gateway system:
• Only the B5800 Branch Gateway phone barrier box should be used with phone V1 modules.
• Only the B5800 Branch Gateway phone barrier box V2 should be used with phone V2 modules.
• No other type of analog phone barrier box should be used.
• Where more than 3 barrier boxes are required in a building, they must be rack mounted using a barrier box rack mounting kit. See
Rack mounting barrier boxes on page 78.
• A maximum of 16 barrier boxes can be used with any phone module.
• The phone barrier box does not connect the ringing capacitor in phone V1 modules.
Main Building
• RJ11 — Connect to PHONE
(POT) port on the Phone module using cable supplied with the barrier box.
• RJ45 — Connect to the secondary building barrier box via primary protection in both buildings.
Barrier Box Secondary Building
• RJ11 — Connect to analog phone. Cable not supplied.
• RJ45 — From main building via primary protection in both buildings.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 77
Hardware and software installation
Main Building
• Center screw — Connect to main building protective ground (or ground terminal of
Barrier Box Rack Mounting
Kit). Use 18AWG (minimum) wire with a green and yellow sleeve.
• Right-hand screw —
Connect to ground point on
Phone module using ground cable supplied with barrier box.
Barrier Box Secondary Building
• Center screw — Connect to main building protective ground. Use 18AWG
(minimum) wire with a green and yellow sleeve.
• Right-hand screw — Not used.
The following wires must be kept apart, that is, the wires cannot be routed in the same bundle:
• Earth leads from the barrier box to the phone modules.
• Internal wires, for example extension leads going directly to the phone modules.
• Wires from external telephone going directly to the barrier boxes.
Rack mounting barrier boxes
About this task
Where more than 3 phone barrier boxes are used they must be rack mounted. The Barrier Box
Rack Mounting Kit (SAP Code 700293905) supports up to 8 phone barrier boxes.
Procedure
1. Unscrew the two screws arranged diagonally at the front of each barrier box and use these same screws to reattach the barrier box to the rack mounting strip.
2. Each barrier box is supplied with a solid green ground wire connected to its functional ground screw. Remove and discard this wire.
3. Connect a green/yellow ground wire to the protective earth screw in the center of the point on the back of the barrier box.
4. The rack mounting strip has threaded M4 earthing pillars. Connect the other end of the barrier box ground wire, using M4 washers and nuts, to the earthing pillar on that side of the rack mounting strip.
78 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Administration software suite
5. Using 14AWG wire with green and yellow sleeve, connect one of the earthing pillars to the buildings protective earth.
6. Using 14AWG wire with green and yellow sleeve, connect the other earthing pillar to the phone module.
7. Ensure that the following wires are not routed together in the same bundle:
• Earth lead from the barrier box to the phone module.
• Internal wires, e.g. wires going directly to the phone module.
• Wires from external telephone going directly to the barrier boxes.
Administration software suite
The IP Office administration software applications are installed on the installation PC. They are used by installers and maintainers to configure, manage, and monitor the B5800 Branch
Gateway system.
The IP Office administration applications are:
• Manager
IP Office Manager is used to access all parts of the B5800 Branch Gateway configuration.
Different levels of access can be defined to control which parts of the configuration the
Manager user can view and alter. Manager is also used to upgrade the system software files.
• System Status
The IP Office System Status application is a monitoring and reporting tool that provides a wide range of information about the current status of the system. It can report the available resources and components within the system and details of calls in progress.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 79
Hardware and software installation
Details of the number of alarms are recorded and the time and date of the most recent alarms.
• System Monitor
The IP Office System Monitor application is a tool that shows details of all activity on the
B5800 Branch Gateway system. Because of the level of detail, interpretation of System
Monitor traces requires a high-level of data and telephony protocol knowledge. Installers and maintainers must understand how to run System Monitor when necessary as Avaya may request copies of System Monitor traces to resolve support issues.
PC requirements
The minimum Microsoft ® Windows ® PC requirements for the B5800 Branch Gateway system tools are provided in the following table. If other applications are to be installed on the PC then those individual requirements should also be met.
Requirement
Processor
RAM
HD Space
Display
Operating System
Minimum
600MHz Pentium or AMD
Opteron, AMD Athlon64,
AMD Athlon XP.
128MB
Recommended
800MHz Pentium or AMD
Opteron, AMD Athlon64,
AMD Athlon XP.
256MB
1GB - 800MB for .NET2,
200MB for Manager.
1.4GB - 800MB for .NET2,
600MB for the full B5800
Branch Gateway Admin suite.
800 x 600 - 256 Colors 1024 x 768 - 16-bit High
Color
Supported on Windows ® XP Pro, Windows ® Vista, Windows ®
7, Windows ® 2003 and Windows ® 2008.
• 32-bit and 64-bit versions are supported.
• Vista support is only on Business, Enterprise and Ultimate versions.
• Windows 7 support is only on Professional, Enterprise and
Ultimate versions.
80 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Installer PC connection
Installing the administration applications
Procedure
1. Using the Add or Remove Programs option in the Windows Control Panel, check that the PC does not have an earlier version of the B5800 Branch Gateway
Administration Suite installed. If there is, uninstall it.
2. Insert the B5800 Branch Gateway Administrator Applications DVD.
3. Select B5800 Branch Gateway Administration Suite.
4. Double-click on setup.exe.
5. Select the language you want to use for the installation process.
This does not affect the language used by Manager when running.
6. Click Next.
7. Select who should be able to run the Administration Suite applications.
8. Click Next.
9. If required, select the destination to which the applications should be installed.
It is recommended that you accept the default destination.
10. Click Next.
The Custom Setup window appears.
11. Select the applications that you want to install. At a minimum select System
Monitor and Manager.
When you select an application, a description of the application appears. Click on the next to each application to change the installation selection.
12. Click Next.
13. Click Install.
Installation of Windows .Net2 components may be required. If dialogs for this appear, follow the prompts to install .Net.
14. If requested, reboot the PC.
Installer PC connection
During installation it is recommended that the B5800 Branch Gateway control unit be started without it being connected to any network. That ensures that the B5800 Branch Gateway defaults to a known set of IP address settings.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 81
Hardware and software installation
The B5800 Branch Gateway control unit is connected to the PC with a standard RJ45–RJ45
LAN cable.
Connecting the PC directly to the control unit
About this task
The default address for a B5800 Branch Gateway control unit LAN port is
192.168.42.1/255.255.255.0. Use this procedure to change the TCP/IP properties for the LAN port on the PC and directly connect the PC to the control unit.
Procedure
1. Change the TCP/IP properties of the LAN port on the PC to the following:
• Fixed IP address: 192.168.42.203
• Subnet mask: 255.255.255.0
• Default gateway: 192.168.42.1
Note:
While setting the PC to be a DHCP client could be used, this is not recommended for performing more advanced functions such as firmware upgrades.
2. Connect the LAN cable from the PC LAN port to the LAN or LAN1 port on the control unit.
3. Check that the orange LED lamp on the control unit LAN port is on.
The green LED may also be flickering. This indicates traffic across the LAN connection.
4. To test the connection before running Manager or the System Status application, do the following: a.
Select Start > Run.
b.
Enter cmd.
c.
In the command window that appears, enter ping 192.168.42.1.
82 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Applying power to the system
The results should show a number of ping replies from the B5800 Branch
Gateway . This confirms basic communication between the Manager PC and the B5800 Branch Gateway .
d.
If there are no ping replies, enter ipconfig.
The results should list the IP address settings of the Manager PC as required above.
e.
If the IP address settings of the Manager PC are displayed, enter exit and check the cable connection.
Applying power to the system
Procedure
1. With the power off on the control unit, insert the B5800 Branch Gateway System
SD card into the System SD slot on the rear of the control unit.
Ensure that you have the correct card. The B5800 Branch Gateway System SD card is required for branch operation. The card is labeled System SD BRANCH
GW.
2. Apply power to the external expansion modules.
The power outlet used must include a switch and in cases where the power cord includes an earth lead, that outlet must have a protective earth connection.
3. Apply power to the control unit.
The power outlet used must include a switch and the power outlet must have a protective earth connection.
When power is applied to the control unit, the following occurs:
• The control unit begins loading firmware from the System SD card with which it will upgrade itself and the components installed in the control unit. This process takes approximately a minute. The end of this process is indicated by
LED1 on each base card flashing every 5 seconds and LED9 on each base card fitted with a trunk daughter card flashing every 5 seconds.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 83
Hardware and software installation
• The control unit will then begin upgrading the external expansion modules.
This is indicated by the red center LED on each module flashing red. The process is completed when the LED changes to steady green.
• If a configuration file is already present on the System SD card, it is loaded by the B5800 Branch Gateway. If not, the B5800 Branch Gateway creates a default configuration based on the components of the system and copies that configuration onto the System SD card.
The B5800 Branch Gateway Initial Installation utility is launched. See
on page 121.
Control unit LEDs startup sequence
The LEDs on the rear of the control unit go through the following sequence during a normal start up. Note that the times are approximate only.
LED
CPU
System
SD
4s 4s 12s 5s 2s 5s 5s 10s 10s Finished
Orng Grn Grn Grn Grn Grn Grn Grn Grn Grn
Red
Orng Off Grn Grn Grn Off Grn Grn Grn Grn
Flash
Grn Grn Grn Optional
SD
(if present)
Orng Off Grn Grn Grn Off Off
Orng = Orange Grn = Green
On the front of the control unit, LED1 on any IP500 base cards fitted is used as follows. LED9 is also used for any trunk daughter cards fitted.
LED
Optional SD Red
30s 30s
Red
Fast Flash
Finished
Red
Flash every 5 seconds
84 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Applying power to the system
About the LEDs
Control unit LEDs
LED
Optional SD
System SD
CPU
Base card LEDs
All cards
Analog phone
Digital station
VCM
4-port expansion
Base Card
Description
• Off = card shutdown
• Green on = card present
• Green flashing = card in use
• Orange steady = reset imminent
• Red flashing = card initializing or shutting down
• Red fast flashing = card full
• Red steady = card failure/wrong type
• Alternate red/green = starting up
• Green on = okay
• Red on = no software
• Flashing Red = error/shutdown
LEDs 1 to 8 Usage
LED1 is used for base card status:
• Red on = error
• Red slow flash = initializing
• Red flash every 5 seconds = card okay
• Red fast flash = system shutdown
No status LEDs are used for analog phone extensions.
Green on = phone detected
LEDs 1 to 8 are unlabelled. They are used to indicate voice compression channel usage.
Each LED lit represents 12.5% of the available voice compression channel capacity in use (total card capacity rather than licensed capacity).
LEDs 1 to 8 are used for the expansion ports on the rear of the control unit. LEDs 9 to 12 are used for the card's own expansion ports.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 85
Hardware and software installation
Base Card
Combination
Trunk daughter card LEDs
All cards
Trunk Daughter Card
Analog trunk
BRI trunk
PRI trunk
LEDs 1 to 8 Usage
• Green on = expansion module present
• Red flashing = initializing
• Red on = error
• Orange regular flash = base card okay
LEDs 1 to 6
Green on = phone detected
LEDs 9 to 12 Usage
LED 9 is used for daughter card status:
• Red on = error
• Red slow flash = initializing
• Red flash every 5 seconds = card okay
• Red fast flash = system shutdown
• Green on =card fitted
• Green flashing = trunk in use
• Off = no trunk present
• Green on = trunk present
• Green flashing = trunk in use
• Off = no trunk present
• Green on = trunk present
• Green flashing = trunk in use
• Red/green fast flash (port 9) or greenfast flash (port 10) = alarm indication signal
(AIS) from the trunk remote end
• Red with green blink (port 9) or green blink
(port 10): port in loopback mode (set through System Monitor)
86 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Default configuration
External expansion module LEDs
External expansion module
All modules
• Green on = module okay
• Red flashing = module starting up
• Red on = error
Default configuration
Unless you loaded a configuration file onto the System SD card, the B5800 Branch Gateway system will be configured with default settings when the system is started.
Following are the basic default configuration settings for a B5800 Branch Gateway system.
Network Settings
IP address
IP mask
DHCP mode
Number of DHCP IP addresses
LAN1
192.168.42.1
255.255.255.0
server
200
LAN2/WAN
192.168.43.1
255.255.255.0
server
200
• Extensions and users — An extension is automatically created for each physical extension port detected in the system. Extension numbers start from 201 and take the form Extn201, Extn202, etc. You must manually configure a user for each extension.
Users are not created automatically. Note that there can be extensions on the system that have not yet had users assigned to them.
• Hunt group — A single hunt group 200 called Main is created and the first 10 users are placed into that hunt group as members.
• Incoming call routes — Two default incoming call routes are created. Voice calls are routed to the hunt group Main. Data calls are routed to the RAS user DialIn.
• Default short codes — A-Law or U-Law variant operation is determined by the Feature
Key installed in the control unit. Depending on the variant, different short codes and trunk settings are added to the default configuration.
• A-Law or Mu-Law — Pulse Code Modulation (PCM) is a method for encoding voice as data. In telephony, two methods of PCM encoding are widely used, A-law and Mu-law
(also called U-law). Typically Mu-law is used in North America and a few other locations while A-law is used by the rest of the world. As well as setting the correct PCM encoding for the region, the A-Law or Mu-Law setting of a B5800 Branch Gateway system when it is first started affects a wide range of regional defaults relating to line settings and other
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 87
Hardware and software installation values. The encoding default is set by the type of Feature Key installed when the system is first started.
Default DHCP/IP address settings
When a defaulted or new B5800 Branch Gateway control unit is switched on, it requests IP address information from a DHCP server on the network. This operation will occur whether the
LAN cable is plugged in or not. The process below is done separately for both the LAN port
(LAN1 in the configuration) and the WAN port (LAN2 in the configuration) on the back of the control unit.
• The B5800 Branch Gateway makes a DHCP request for what IP address information it should use.
• If a DHCP server responds within approximately 10 seconds, the control unit defaults to being a DHCP client and uses the IP address information supplied by the DHCP server.
Note:
For this installation, we have not yet connected the control unit to the network so a
DHCP server will not respond.
• If a DHCP server does not respond, the control unit defaults to being the DHCP server for the LAN using the following settings:
- For its LAN1 it allocates the IP address 192.168.42.1 and IP Mask 255.255.255.0.
It supports 200 DHCP clients using the addresses range 192.168.42.2 and
192.168.42.201, the IP Mask 255.255.255.0 and default gateway address
192.168.42.1 (the control unit LAN1 address).
- For its LAN2 if supported, it allocates the IP address 192.168.43.1 and IP Mask
255.255.255.0.
- Note that the B5800 Branch Gateway does not check that these addresses are valid and or available on the network.
Important:
Once the control unit has obtained IP address and DHCP mode settings, it retains those settings even if rebooted without a configuration file present on the System SD card. To fully remove the existing IP address and DHCP mode setting the B5800 Branch Gateway must be defaulted using Manager.
Connecting the control unit to the network
Before you begin
The system default settings must be changed to match the customer requirements before the control unit is connected to the network. Use the Initial Installation Utility to assist in configuring
the system settings. To run the Initial Installation Utility, see Using the Initial Installation
on page 121.
The Initial Installation Utility is run using IP Office Manager from a PC or laptop that is connected directly to the B5800 Branch Gateway LAN 1 port. The Initial Installation Utility will
88 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Connecting phones automatically detect the B5800 Branch Gateway and connect regardless of the PC or B5800
Branch Gateway LAN settings. This utility can be run on site or while the B5800 Branch
Gateway control unit is being staged off site.
Note:
IP Office Manager preferences must be set to:
• UDP discovery and 255.255.255.255 (File > Preferences > Discovery tab)
• Auto Connect on start up (File > Preferences > Preferences tab)
About this task
Once you have changed the B5800 Branch Gateway system default settings to those that match the customer requirements, use this task to connect the B5800 Branch Gateway control unit to the customer's network.
Procedure
1. Disconnect the LAN cable from the installer PC.
2. Connect the LAN cable to the customer network.
3. If you want to use the administration PC for on-going administration, connect the
PC to the customer network.
Connecting phones
Procedure
1. Connect the analog phones to the phone ports.
2. Ensure that the analog phones that are connected to power failure ports are clearly labeled as such.
3. Connect the Avaya digital phones to the appropriate DS ports.
When the control unit is started, after loading its own firmware and the firmware for its external expansion modules, it will upload the appropriate firmware to the digital phones.
Avaya H.323 phones do not need to be connected at this stage. They will go through a firmware upgrade process when connected to a B5800 Branch Gateway system that is already running.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 89
Hardware and software installation
90 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Chapter 6: About preserving staged button programming for BST phones
Business Series Terminal (BST) phones are the M7 and T7 Digital Series Phones used by a BCM system.
When migrating a BCM system to a B5800 Branch Gateway system, the M7 and T7 phones can be reused.
When staging the T7 and M7 phones, user extensions are added and button programming is set up.
However, when a staged T7 or M7 phone is plugged into the B5800 Branch Gateway system, the configured user extension and button programming is lost, and the BST phone returns to the default button programming.
A short code can be configured to preserve the user's extension configuration so that the configuration is not lost when the phone is plugged into the B5800 Branch Gateway system.
Configuring a short code to preserve the user extension configuration
About this task
Use this task to configure a short code for the user extension so that the extension programming performed when staging the T7 and M7 phones is preserved when the phone is plugged into the B5800 Branch Gateway system.
Procedure
1. Start Manager and connect to the B5800 Branch Gateway.
2. In the left navigation pane, click User.
3. Click the appropriate user and then click the ShortCodes tab.
4. Click Add.
5. In the Code field, enter *DCP.
6. In the Feature drop-down box, accept the default value, Dial.
7. In the Telephone Number field, enter 84000004,0,1,1,0.
Note:
In the 4000004 portion of the telephone number, the first digit in the sequence preserves the phone's contrast level. This value can be 1 – 9. The last digit in the sequence preserves the phone's ring volume attenuation level. This value can
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 91
About preserving staged button programming for BST phones be 0 – 7. Note that because it is attenuation, the higher the value, the lower the ring volume. For example, 0 is full volume.
8. In the Line Group Id drop-down box, accept the default value, 0.
9. In the Locale drop-down box, accept the default value, blank.
10. For the Force Account Code check box, accept the default value, unchecked.
11. Click OK.
The short code is displayed in the ShortCodes tab.
12. Repeat steps 3 through 11 for each user whose data programming you want to preserve.
Remotely forcing a BST phone to return to default settings
About this task
Use this task to remove the DCP code to remotely force a BST phone to return to default button programming and default contrast and ring volume settings for that set type.
Note:
Although calls currently active on the phone should not be affected, use caution when you force a BST phone to return to default settings.
Procedure
1. Start Manager and connect to the B5800 Branch Gateway.
2. In the left navigation pane, click User.
3. Click the appropriate user and then click the ShortCodes tab.
4. Select the DCP short code and then click Remove.
For the BST phone currently connected to that user extension, the following occurs:
• Button programming per the BST phone model currently connected to that user extension is returned to the default setting.
• BST phone contrast is returned to the default setting.
5. Click OK.
Note:
You can also use this procedure to reset a user extension so that the next time a BST phone model of any type is connected to it, that user’s programming will be defaulted appropriately to that BST phone.
92 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Other DCP short codes
Other DCP short codes
There are other DCP short codes that preserve the user's extension configuration so that the configuration is not lost when the phone is plugged into the B5800 Branch Gateway system.
• *DCP 4???????,0,1,1,0 Dial 0 (where ? is probably 0, but could be another number) —
The presence of this short code will preserve button programming for a newly connected
BST phone.
This short code indicates there was a B5800 Branch Gateway phone other than a BST phone plugged into this user extension. If a DCP short code telephone number starts with a 4 rather than an 8, this indicates there was never a BST phone connected to this user extension. However, because there was at some point another B5800 Branch Gateway phone connected to this user extension, the assumption is to preserve the staged BST phone button programming.
• *DCP c400000,0,1,1,0 Dial 0 — The presence of this short code will preserve button programming for a newly connected BST phone.
This short code indicates there was a B5800 Branch Gateway phone other than a BST phone and a BST phone plugged into this user extension. The assumption is to preserve the staged BST phone button programming.
Any other format of the DCP short code than those listed above or explained in
phone connection from defaulting all staged button programming. Only a short code in one of the following formats will prevent the staged button programming from returning to the default configuration:
• *DCP 8???????,0,1,1,0 …
• *DCP 4???????,0,1,1,0 …
• *DCP c???????,0,1,1,0 …
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 93
About preserving staged button programming for BST phones
94 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Chapter 7: Upgrading an R6.2 system with an R6.2 service pack
This chapter is for B5800 Branch Gateway systems that have already been upgraded from R6.1 to R6.2.
Avaya periodically releases service packs to provide updates that fix existing problems or provide enhancements.
This chapter describes how to perform an upgrade using Avaya Aura ® System Manager. Avaya Aura ®
System Manager should be used on R6.2 systems when multiple branches require upgrades.
Two other methods which require using IP Office Manager that is connected directly to the B5800 Branch
Gateway system are available to perform an upgrade. You can perform an upgrade using the IP Office
Manager upgrade wizard or using the System SD card. For more information, see:
•
Using the upgrade wizard on page 219
•
System upgrade using the System SD card on page 258
R6.2 service pack installation checklist
# Description Section
1 Create a backup of the system configuration.
2 Synchronize the B5800 Branch
Gateway with System Manager.
See Creating a backup of the system configuration using System Manager on
page 217.
See Synchronizing B5800 Branch Gateway with System Manager on page 164.
3 Set up an external server to act as a remote software library.
See Remote Software Library for B5800
Branch Gateway upgrades on page 96.
4 Get the inventory.
5 Configure PLDS access.
6
7
Create a software library.
Upgrade the B5800 Branch
Gateway.
See Getting inventory on page 98.
See Configuring user PLDS access
on page 99.
See Creating a software library
on page 100.
See Upgrading the B5800 Branch Gateway using System Manager on page 101.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 95
Upgrading an R6.2 system with an R6.2 service pack
Remote Software Library for B5800 Branch Gateway upgrades
For the B5800 Branch Gateway firmware upgrade files, an external server is required to act as a remote software library. This server hosts the firmware upgrade files through HTTP. The external server should have an FTP, SCP, or SFTP server to upload the firmware files from
System Manager. While downloading from the PLDS web site, the firmware files are temporarily copied on System Manager. The FTP, SCP, or SFTP protocols are then used to copy the firmware files from System Manager to the external server. This file transfer from
PLDS to System Manager and then to the external server is a single operation for the administrator.
Note:
The HTTPS protocol is not supported for a B5800 Branch Gateway device to pull files from the external server.
Downloading the firmware files from PLDS to the B5800 elements through
System Manager
1. Download the B5800 firmware from PLDS to the System Manager cache using the credentials provided in User Settings in System Manager.
2. Upload the firmware to the external server from the System Manager cache using the FTP or SCP or SFTP protocol and the configuration information in the software library.
3. After the file is on the external server, B5800 elements use this file during upgrade using HTTP protocol.
Note:
Steps 1 and 2 happen simultaneously. The file download to System Manager is transparent.
System requirements for the external server
Recommendation Component
Operating System
Requirement
Any standalone or virtualized
Windows or Linux
Distribution.
96 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Remote Software Library for B5800 Branch Gateway upgrades
Component
Hard Drive
Requirement
20GB free space
Recommendation
There should be enough free space on the hard drive to store the firmware files.
Memory
Protocols (for the
B5800 Branch
Gateway elements to download files from the external server)
2GB
HTTP server
As required by the operating system and the supported protocol services.
Any supported HTTP server installation.
Note:
The HTTPS protocol is not supported for a B5800 Branch
Gateway device to pull files from the external server.
Protocols (for downloading the firmware upgrade files to the external server from the PLDS web site via System
Manager)
An FTP, SCP or SFTP server
(running on default ports)
Use SFTP or SCP for secure file transfer.
Setting up the external server to work as a remote software library for B5800 upgrades
Procedure
1. Install the operating system.
2. Install any supported HTTP server.
3. Install any one of the supported servers: FTP, SFTP, or SCP.
4. Configure users for the FTP or SFTP or SCP access. These users should have read, write, and delete permissions for the directories configured to function as the storage location for the upgrade files.
5. Configure the HTTP server such that the location where the upgrade files are downloaded is accessible using an HTTP URL. This URL is used to configure the external server as a software library on System Manager. As B5800 elements use this HTTPS URL to pull the firmware files during upgrade, the URL must be reachable to the B5800 elements.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 97
Upgrading an R6.2 system with an R6.2 service pack
Getting inventory
Before you begin
Ensure that all B5800 Branch Gateway devices have been added to System Manager. There are several methods available to add the B5800 Branch Gateways to System Manager. All methods require that you identify each individual B5800 Branch Gateway. See
B5800 Branch Gateways to System Manager
on page 126 for more information.
The B5800 Branch Gateway devices to be discovered for upgrades should be SNMP enabled and the corresponding SNMPv1 communities must be set correctly in System Manager. See
Setting B5800 Branch Gateway SNMP attributes on page 98 for more information.
About this task
Use this task to collect the components of a B5800 Branch Gateway that has been added on
System Manager.
Note:
This task does not automatically find the new B5800 Branch Gateways. The B5800 Branch
Gateway must first be added to System Manager. Then this task will collect the components for the B5800 Branch Gateway that was added to System Manager.
B5800 Branch Gateways that are added to System Manager using the discovery method
described in Discovering B5800 Branch Gateways
on page 126 already have their inventory details collected. You do not need to perform this task to upgrade those B5800 Branch
Gateways.
Procedure
1. From the System Manager console, under Elements, click Inventory.
2. On the Inventory page, on the left navigation pane, click Upgrade Management
> Manage Software.
3. On the Manage Software page, click Get Inventory.
4. Do one of the following:
• Click Now to get the device inventory.
• Click Schedule to get the device inventory at a later time.
Setting B5800 Branch Gateway SNMP attributes
Procedure
1. From the System Manager console, under Elements, click Inventory.
98 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Configuring user PLDS access
2. On the Inventory page, on the left navigation pane, click Manage Elements.
3. Click the check box for the appropriate element.
4. Click Edit.
5. On the Edit <system name> page, click the Attributes tab.
6. In the SNMP Attributes section, do the following: a.
For the Version, click the radio button for V1.
b.
In the Read Community field, enter the read community of the device.
c.
In the Write Community field, enter the write community of the device.
d.
In the Retries field, select the appropriate number of times the application should poll the device without receiving a response before timing out.
e.
In the Timeout (ms) field, select the appropriate number of milliseconds that the application should poll the device without receiving a response before timing out.
f.
In the Device Type drop-down box, select the appropriate device type.
7. Click Commit.
Configuring user PLDS access
About this task
Use this procedure to configure user PLDS access and define the default support site.
Procedure
1. From the System Manager console, under Elements, click Inventory.
2. On the Inventory page, click Upgrade Management > User Settings.
3. On the User Settings page, click Edit.
4. For the Use Avaya Support Site check box, accept the default setting, checked.
Note:
Use Other Website only if a service technician directs you to use an alternate site for downloads.
5. In the SSO User Name field, enter the user's SSO user name for PLDS.
6. In the SSO Password field, enter the user's SSO password for PLDS.
7. Click the Use Proxy check box if the user has a proxy.
8. In the Host field, enter the host details for this proxy server.
9. In the Port field, enter the port number for this proxy server.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 99
Upgrading an R6.2 system with an R6.2 service pack
10. Click Commit.
Creating a software library
Procedure
1. From the System Manager console, under Elements, select Inventory.
2. On the Inventory page, click Upgrade Management > Software Library.
3. Click New.
4. On the Add Software Library page, in the Library Server Details tab, do the following: a.
In the Name field, enter the appropriate name.
b.
In the IP Address field, enter the IP address of the library server.
c.
In the Description field, enter a description of this library server as appropriate.
d.
In the Server Path field, enter the full path of the software library location e.
To use this software library as the default, click the Default Library check box.
f.
If this software library is remote, click the Remote Library check box.
g.
In the Default Protocol drop-down box, select the appropriate protocol.
h.
Click the HTTP/HTTS check box.
i.
In the HTTP/HTTS URL field, enter the appropriate URL to the firmware files in
Software Library.
j.
Depending on the default protocol you selected in step g, click on the corresponding tab (FTP Configuration, SCP Configuration, or SFTP
Configuration) and configure the authentication parameters as required.
Note:
Configuring the authentication parameters for the default protocol is mandatory.
k.
Click Commit.
100 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Upgrading the B5800 Branch Gateway using System Manager
Upgrading the B5800 Branch Gateway using System
Manager
About this task
Use this task to upgrade the B5800 Branch Gateway. Included in this task are the steps to:
• analyze the software to determine if a new version is available
• download the firmware files from Avaya PLDS
Avaya PLDS will automatically determine if a newer software version than what is currently installed is available. If there is a newer version available, you can download the newer version to upgrade the B5800 Branch Gateway. To determine if there is a new software version available, Avaya PLDS uses the file versions_sp.xml that is available from the Avaya Support
Site to compare the current installed software on the device with the latest available on Avaya
PLDS. The file versions_sp.xml is regularly updated with the latest firmware/software releases available for upgrade.
Procedure
1. From the System Manager console, under Elements, select Inventory.
2. On the Inventory page, click Upgrade Management > Manage Software.
3. On the Manage Software page, click More Actions > Analyze Now.
4. When the analyze job is finished running, refresh the table.
A red x indicates there is a newer firmware version available that has not been downloaded to the software library.
5. Select the control unit for upgrade, and click Download.
6. On the File Download Manager page, do the following: a.
In the Library drop-down box, select the appropriate library.
b.
In the Protocol drop-down box, accept the protocol displayed.
Note:
The appropriate protocol is automatically selected based on the selected library.
c.
Expand the tree to show a list of the upgrade packages that are available.
d.
Under the Device Type B5800, select the latest package.
7. Do one of the following:
• Click Now to download the software.
• Click Later to schedule the download at a specified time.
8. Click Download.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 101
Upgrading an R6.2 system with an R6.2 service pack
The system displays the End User License Agreement page.
9. Click Accept to download the software.
10. When the download is complete, go to the Manage Software page.
A yellow i indicates there is a newer version of software downloaded to the remote software library and the device can be upgraded.
11. Click the check box for the appropriate control unit.
12. Click Upgrade.
The Upgrade button is enabled only if the state of the device is yellow.
13. On the B5800 Branch Gateway Upgrade Configuration page, select the appropriate library and the release to which you want to upgrade.
By default, the library which has the latest upgrade package is automatically selected.
14. Do one of the following:
• Click Now to start the upgrade.
• Click Later to schedule the upgrade at a specified time.
15. To view the upgrade status, on the Manage Software page, click the B5800 Branch
Gateway being upgraded, then click Status.
When the upgrade is complete, a final status window is displayed. The state of the device turns green showing that it has the latest firmware installed.
102 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Chapter 8: Administration software suite
The IP Office administration software applications are installed on the installation PC. They are used by installers and maintainers to configure, manage, and monitor the B5800 Branch Gateway system.
The IP Office administration applications are:
• Manager
IP Office Manager is used to access all parts of the B5800 Branch Gateway configuration. Different levels of access can be defined to control which parts of the configuration the Manager user can view and alter. Manager is also used to upgrade the system software files.
• System Status
The IP Office System Status application is a monitoring and reporting tool that provides a wide range of information about the current status of the system. It can report the available resources and components within the system and details of calls in progress. Details of the number of alarms are recorded and the time and date of the most recent alarms.
• System Monitor
The IP Office System Monitor application is a tool that shows details of all activity on the B5800
Branch Gateway system. Because of the level of detail, interpretation of System Monitor traces requires a high-level of data and telephony protocol knowledge. Installers and maintainers must understand how to run System Monitor when necessary as Avaya may request copies of System
Monitor traces to resolve support issues.
Starting System Status
About this task
The IP Office System Status application is a monitoring and reporting tool that provides a wide range of information about the current status of the system. It can report the available resources and components within the system and details of calls in progress. Details of the number of alarms are recorded and the time and date of the most recent alarms.
Procedure
1. To start the System Status application, choose one of the following:
• On the PC where System Status has been installed, select Start > Programs
> Avaya B5800 Branch Gateway Admin Suite > System Status.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 103
Administration software suite
• If Manager is also installed and is running, select File > Advanced > System
Status.
• Start a web browser and enter the IP address of the B5800 Branch Gateway control unit. Then select the System Status Application link.
The Logon window appears.
2. In the Logon window, enter the details of the B5800 Branch Gateway system to which you want it to connect as follows: a.
In the Control Unit IP Address drop-down box, select the appropriate address, or enter the IP address of the control unit.
b.
In the Services Base TCP Port field, enter the Services Base TCP Port setting that was set in the system's security settings. The default is 50804 c.
In the Local IP Address field, enter the appropriate local IP address. If the PC has more than one IP address assigned to its network card or multiple network cards, the address to use can be selected if necessary.
d.
In the User Name field, enter a user name that has been configured for System
Status access in the B5800 Branch Gateway security settings.
e.
In the Password field, enter the appropriate password.
f.
Check the Auto Reconnect check box if you want System Status to attempt to reconnect using the same settings if connection to the B5800 Branch Gateway is lost.
3. Click Logon.
Starting System Monitor
About this task
The IP Office System Monitor application is a tool that shows details of all activity on the B5800
Branch Gateway system. Because of the level of detail, interpretation of System Monitor traces requires a high-level of data and telephony protocol knowledge. Installers and maintainers must understand how to run System Monitor when necessary as Avaya may request copies of System Monitor traces to resolve support issues.
Procedure
1. Select Start > Programs > Avaya B5800 Branch Gateway Admin Suite >
Monitor.
If System Monitor has been run before it will attempt to connect with the system which it monitored previously.
2. To monitor a different system, select File > Select Unit.
The Select System to Monitor window appears.
104 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Starting System Monitor
3. In the Control Unit IP Address drop-down box, select the IP address of the control unit you want to monitor.
4. In the Password field, enter the appropriate password.
Note:
You are able to set a System Monitor password using Manager. If the B5800
Branch Gateway does not have a System Monitor password set, System Monitor uses the B5800 Branch Gateway System password. The System Monitor password and System password are both set within the B5800 Branch Gateway system security settings.
5. For Control Unit Type, select Avaya B5800 Branch Gateway.
6. Click OK.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 105
Administration software suite
106 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Chapter 9: Initial branch configuration
This chapter provides initial configuration tasks required for each B5800 Branch Gateway deployed in the distributed branch user model.
Configuration checklist
Use this checklist to monitor your progress as you configure a B5800 Branch Gateway system deployed as a distributed branch in a CS 1000 configuration.
# Description Section
1 Confirm that your version of Avaya
Aura
®
System Manager is R6.2 and
SP1 has been installed.
2 Download IP Office Manager onto the System Manager server.
3 Install the shared PLDS license file on the System Manager WebLM server.
4 Perform a certificate exchange between CS 1000 and Avaya Aura
®
System Manager.
See Setting up System Manager to launch
on page 111.
Note:
This task is not required if you have downloaded the B5800AdminLite.exe
file using the Upgrade Management link in System Manager.
See Installing the shared PLDS license file on the System Manager WebLM server
on page 115.
Note:
If you are using the individual licensing
method, see Using Manager to deliver license files to the branches on
page 115.
See Performing a certificate exchange between CS 1000 and Session Manager
on page 117.
Note:
Steps 1 through 4 only need to be performed one time. They do not need to be performed for each new B5800 Branch Gateway.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 107
Initial branch configuration
# Description Section
5 Generate a certificate on Avaya
Aura
®
System Manager.
See Generating a certificate on System
6 Run the Initial Installation Utility. The
Initial Installation utility provides configuration and security settings that minimize initial installation activities and maximize security.
See Using the Initial Installation Utility on
page 121.
Note:
When you run the Initial Installation
Utility, a security certificate is automatically installed on the B5800
Branch Gateway. If you do not run the
Initial Installation Utility, you must manually configure the SCEP and security settings on the B5800 Branch
Gateway. This is not the preferred method, but can be used as an alternative. For more information, see
Configuring the B5800 Branch Gateway for certificates on page 124.
7 Add the B5800 Branch Gateways to
System Manager.
on page 126. In this task, you add the branch to System Manager by identifying the subnet IP address in which the branch is located. This task must be performed for each B5800 Branch Gateway that you want to manage from System
Manager.
As an alternative, you can also use one of the following methods to add the B5800
Branch Gateways to System Manager:
•
on page 128.
This method requires that you first add each B5800 Branch Gateway to an xml file. The xml file is then used to import the devices to System Manager.
•
Adding the B5800 Branch Gateways to
System Manager on page 130. In this
task, you manually add each branch to
System Manager by identifying the IP address of the B5800 Branch Gateway.
This task must be performed for each
B5800 Branch Gateway that you want to manage from System Manager.
8 Confirm that WebLM licensing for the branch is enabled.
See Enabling WebLM licensing for the branch
on page 131.
108 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Configuration checklist
# Description Section
9
Create a system template. (Optional) See Creating a system template
on page 131.
10 Upload an auto attendant audio file.
(Optional)
Uploading an auto attendant audio
11 Apply the system template to one or more branches. (Optional)
12 Create an endpoint template.
page 133.
page 133.
on
on
Note:
You must create a B5800 Branch
Gateway endpoint template. You cannot add a user in System Manager unless an endpoint template has been created.
Note:
• Steps 13 through 24 are performed to modify a B5800 Branch Gateway configuration as needed.
• Steps 25 through 32 are performed to configure Avaya Aura
®
Session
Manager.
• Step 33 is performed to configure B5800 Branch Gateway users from User
Management within System Manager.
13
14
15
16
Disable unused trunks.
Set a trunk clock quality setting.
Set trunk prefixes.
Enable SIP trunk support.
See Disabling unused trunks on
page 135.
See Setting a trunk clock quality setting
on page 137.
See Setting the trunk prefixes
on page 138.
See Enabling SIP trunk support on
page 140.
See Setting the branch prefix and local number length for extension numbering on
page 141.
17 Set the branch prefix and local number length for the extension numbering.
18 Change the default codec selection.
See Changing the default codec selection on page 144.
19
Change the maximum SIP sessions. See Changing the maximum SIP sessions on page 145.
20 Add a Session Manager line.
See Adding an Avaya Aura Session
on page 146.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 109
Initial branch configuration
# Description Section
21 Add a second Session Manager line for redundancy.
22 Set up outgoing call routing.
This procedure includes the steps to configure TLS transport for the Session
Manager line.
See Avaya Aura Session Manager line redundancy on page 152.
• See Setting up outgoing call routing
on page 153.
• For information on routing back to the branch for fallback alternate routes, see
Branch PSTN call routing examples
on page 291.
23 Configure the type of voicemail system the branch will use.
24 Enable branch SIP extension support.
on page 173.
See Enabling branch SIP extension support .
Note:
Steps 25 through 32 are performed to configure Avaya Aura
®
Session
Manager.
25 View a list of the SIP domains.
26 Create a location.
See Viewing the SIP domains on
page 168.
See Creating locations on page 168.
27 Create a digit adaptation.
28 Create a SIP entity.
on page 169.
29 Create an entity link.
30 Create a time range.
31 Create a routing policy.
32 Create a dial pattern.
33 Add distributed users. These tasks are performed from Avaya Aura
®
System Manager using the User
Management feature.
on page 170.
See Creating time ranges on page 171.
on page 171.
on page 172.
See User administration on page 187.
110 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Setting up System Manager to launch IP Office Manager
Setting up System Manager to launch IP Office Manager
About this task
From the administration PC, you can use the full version of IP Office Manager available on the
B5800 Branch Gateway Administrator Applications DVD or IP Office Manager Lite that is provided in the B5800AdminLite.exe file to view and edit a B5800 Branch Gateway system configuration or security configuration from System Manager. System Manager launches either version of IP Office Manager in the appropriate mode for the configuration task that was initiated, such as endpoint or template configuration.
If you use IP Office Manager that was installed from the B5800 Branch Gateway Administrator
Applications DVD, you must ensure the version installed on the administration PC is the same version in the B5800AdminLite.exe file. If they are not the same version, you must either upgrade the version of IP Office Manager on the administration PC or you must update the version of IP Office Manager in the System Manager file. To update the version in the System
Manager file, update the parameter abg_b5800_mgr_version in the file /opt/Avaya/ABG/ tools/ManagerSFXVersion.properties
with the version of IP Office Manager that is installed on the administration PC.
To use IP Office Manager Lite to manage the B5800 Branch Gateways, download the
B5800AdminLite.exe file to the System Manager server as follows:
Note:
This task is not required if you have downloaded the B5800AdminLite.exe file using the
Upgrade Management link in System Manager.
Procedure
1. Download the B5800AdminLite.exe file from http://plds.avaya.com
.
2. Transfer the downloaded B5800AdminLite.exe file to the System Manager server to the directory /opt/Avaya/ABG/<version>/tools. For example, /opt/
Avaya/ABG/6.2.12/tools .
Use any SCP or SFTP protocol to connect to the server and transfer the file. You may use any client to perform this step.
3. Change this file into an executable file using the command chmod +x <file
name>.
4. Create a soft link using the name ManagerSFX.exe for the uploaded file, as follows: a.
Go to $ABG_HOME/tools by entering cd $ABG_HOME/tools.
b.
Use the command ln –sf <target> <linkname> to create the soft link.
For example, if the file name uploaded to $ABG_HOME/tools is
B5800AdminLite.exe, then enter ln –sf B5800AdminLite.exe
ManagerSFX.exe
.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 111
Initial branch configuration
5. Using any Linux editor, update the parameter abg_b5800_mgr_version in the / opt/Avaya/ABG/<version>/tools/ManagerSFXVersion.properties
file with the version of IP Office Manager you downloaded from PLDS.
Important:
You must update the parameter abg_b5800_mgr_version each time you download a new version of IP Office Manager from PLDS and transfer to System
Manager. If you fail to do so, when you try to launch IP Office Manager from
System Manager, the launch will fail and the system will display an error message prompting you to update the parameter.
6. On the administration PC that will be used to launch IP Office Manager Lite, set the environment variable to match the version of the B5800AdminLite.exe file.
Depending on the version of Windows running on the PC, do one of the following:
• If the PC is running Windows 7, go to step 7.
• If the PC is running Windows XP, go to step 8.
7. If the PC is running Windows 7, do the following: a.
From the Start menu, right-click Computer.
b.
Click Properties.
c.
In the left navigation pane, click Advanced system settings.
d.
In the System Properties dialog box, click Environment Variables.
e.
In the Environment Variable dialog box, in the User variables for <name> area, select AVAYAB5800_VER.
f.
Click Edit.
g.
In the Edit User Variables dialog box, in the Variable value field, change the value to match the version of B5800AdminLite, for example, 6.2.
h.
Click OK.
i.
Click OK for each subsequent dialog box, and then click Apply.
8. If the PC is running Windows XP, do the following: a.
From the Start menu, right-click My Computer.
b.
Click Properties.
c.
In the System Properties dialog box, click the Advanced tab.
d.
Click Environment Variables.
e.
In the Environment Variables dialog box, in the User variables for <name> area, select AVAYAB5800_VER.
f.
Click Edit.
g.
In the Edit User Variable dialog box, in the Variable value field, change the value to match the version of B5800AdminLite, for example, 6.2.
h.
Click OK.
i.
Click OK for each subsequent dialog box, and then click Apply.
112 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Setting up System Manager to launch IP Office Manager
9. Install IP Office Manager Lite on the administration PC. See
Manager from the System Manager server to a PC on page 113.
Installing IP Office Manager from the System Manager server to a
PC
Before you begin
The B5800AdminLite.exe file has been downloaded to the System Manager server.
About this task
Perform this task to install IP Office Manager from the System Manager server to a PC. Once you perform this task, the next time you attempt to view or edit a B5800 Branch Gateway device from System Manager on this PC, IP Office Manager will automatically launch.
Procedure
1. From the System Manager console, under Elements, select B5800 Branch
Gateway.
2. In the left navigation pane, click System Configuration.
3. On the B5800 Branch Gateway System Configuration page, select the B5800
Branch Gateway device whose system configuration you want to view or edit.
4. At the prompt Do you want to download Avaya B5800 Branch Gateway Manager
from the server now?, click Yes.
5. In the File Download dialog box, click Save.
6. Save the file to an appropriate directory, for example C:\Program Files\Avaya
\B5800.
7. After the download completes, in the Download complete dialog box, click Run.
8. In the Internet Explorer - Security Warning dialog box where you are prompted
Are you sure you want to run this software? click Run.
9. In the WinZip Self–Extractor dialog box where you are prompted Do you want to
install IP Office Manager? click Setup.
10. In the IP Office Manager Lite – InstallShield Wizard dialog box, do the following: a.
In the Welcome dialog box, click Next.
b.
In the Customer Information dialog box, click Next.
c.
In the Destination Folder dialog box, click Next.
d.
In the Custom Setup dialog box, click Next.
e.
Click Install.
f.
In the InstallShield Wizard Completed dialog box, click Finish.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 113
Initial branch configuration
11. Restart your PC.
12. To verify your PC is configured correctly, select My Computer > System Properties
> Advanced tab > Environment Variables.
Activating license files
About this task
B5800 Branch Gateway R6.2 uses the Avaya Product Licensing and Delivery System (PLDS) and integration with Web License Manager (WebLM) for B5800 Branch Gateway license management. B5800 Branch Gateway R6.2 also supports local licensing using an individual
PLDS license file that can be installed directly on the B5800 Branch Gateway using B5800
Branch Gateway Manager (provided in R6.1). For more information about both of these
licensing methods, see Licensing
on page 16.
Note:
B5800 Branch Gateway supports a 30-day grace period during which time the system is fully functional if:
• a license error is detected
• the WebLM server is not available (for example, due to loss of connectivity between the B5800 Branch Gateway and the WebLM server, if using the WebLM licensing method)
• a license file cannot be obtained (for example, due to loss of WAN connectivity, if using the local PLDS licensing method)
Procedure
1. See Activating license entitlements
on page 193 to generate the licenses.
2. See one of the following:
• To use the WebLM licensing method and install the license file on the WebLM
server, see Installing the shared PLDS license file on the System Manager
• To use the individual PLDS licensing method and install the license file on the
B5800 Branch Gateway, see Using Manager to deliver license files to the branches on page 115.
Note:
If the B5800 Branch Gateway is centrally managed by System Manager, to install the individual PLDS license file on the B5800 Branch Gateway using
Manager, you must first disable the System Manager administration feature for the branch. See
114 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Activating license files license file, you must change the B5800 Branch Gateway back to System
Manager control by enabling the System Manager administration feature for the branch.
An alternative method to install the individual PLDS license on a B5800 Branch
Gateway that is centrally managed by System Manager is to use the
Embedded File Management feature available in B5800 Branch Gateway
Manager. You do not need to disable/enabled System Manager administration for the branch using this method. See
Using Embedded File Management to install a PLDS license
on page 116 for more information.
Installing the shared PLDS license file on the System Manager
WebLM server
Before you begin
A shared B5800 Branch Gateway license file has been activated with the Host ID of the WebLM
server. See Activating license entitlements
on page 193.
Procedure
1. On the System Manager console, under Services, click Licenses.
2. In the left navigation pane, click Install License.
3. Click the Browse button and navigate to the appropriate license file.
4. Click the Install button.
Using Manager to deliver license files to the branches
Before you begin
License files have been activated with the Host ID (that is, the Feature Key Serial Number) printed on the B5800 Branch Gateway System SD card. See
Activating license entitlements on page 193.
About this task
You can use Manager to distribute activated license files to B5800 Branch Gateway sites. This procedure explains how to distribute the license files to a single branch at a time.
If the B5800 Branch Gateway is centrally managed by System Manager, you must first disable the System Manager administration feature for the branch. After you download the license file,
you must then enable the System Manager administration feature for the branch. See Disabling
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 115
Initial branch configuration
the System Manager administration feature for the branch from System Manager on
page 162.
Procedure
1. Start Manager and connect to the B5800 Branch Gateway system.
2. In the left navigation pane, select PLDS License.
3. Right-click PLDS License and select Send license file to Avaya Branch
Gateway.
4. In the Upload Files window, select the PLDS license xml file.
Manager copies the license file to the B5800 Branch Gateway SD card where it is validated and stored for persistent use.
5. Select File > Close Configuration.
6. To view the license, select File > Open Configuration.
Using Embedded File Management to install a PLDS license
Before you begin
License files have been activated. See Activating license entitlements
on page 193.
About this task
Use this procedure to install an individual PLDS license on a B5800 Branch Gateway that is centrally managed by System Manager. To use this feature you must rename the PLDS license file to PLDStemp.xml. The B5800 Branch Gateway will validate the PLDStemp.xml file, and if the validation succeeds the B5800 Branch Gateway will automatically rename the file to
PLDSkeys.xml and save it (overriding the previous valid license file, if any was installed).
Note:
When you use Manager to install the license file, you do not need to rename the PLDS license file. The Manager application automatically renames the PLDS license file to
PLDStemp.xml. See
Using Manager to deliver license files to the branches
on page 115.
Procedure
1. Start Manager.
2. Select File > Advanced > Embedded File Management.
3. In the Select B5800 window, click the check box next to the B5800 Branch Gateway system.
4. Click OK.
5. In the B5800 Embedded File Management dialog box, enter the Service User
Password.
116 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Performing a certificate exchange between CS 1000 and Session Manager
6. Click OK.
7. In the Folders pane on the left, select System SD > System > Primary.
8. Select File > Upload file.
9. Select the PLDStemp.xml file.
10. Click OK.
The Upload System Files window appears and shows the upload progress.
11. When the upload is complete, click Close.
12. From the Primary folder, perform a refresh.
The B5800 Branch Gateway error mode will change to License Normal Mode. The
PLDStemp.xml filename is automatically renamed to PLDSkeys.xml.
Note:
If the PLDS file is not accepted by B5800 Branch Gateway, the B5800 Branch
Gateway will remain in License Error Mode and the PLDStemp.xml file is not renamed.
Performing a certificate exchange between CS 1000 and
Session Manager
About this task
To enable CS 1000 and Session Manager to use TLS for secure communications, security certificates must be exchanged between the two systems.
Note:
If UCM and System Manager are in the same security domain, you do not need to perform
the security certificate exchange described in this section. See Unified Communications
Management and System Manager integration
on page 42 for more information.
For more information on CS 1000 certificate management, see Chapter 7 in Security
Management Fundamentals, Avaya Communication Server 1000, document number
NN43001-604.
To exchange certificates between CS 1000 and Session Manager, you must:
Procedure
1. Export the System Manager certificate. See Exporting the System Manager certificate on page 118.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 117
Initial branch configuration
3. Add System Manager as a certificate authority. See
Adding System Manager as a certificate authority on page 118.
Exporting the System Manager certificate
Procedure
1. From the System Manager console, under Services, select Security.
2. On the Security page, in the left navigation pane, select Certificates >
Authority.
3. Click the Download pem file link.
4. In the File Download dialog box, click Save to save the file to the local desktop.
Exporting the CS 1000 security certificate
Procedure
1. From the Avaya Unified Communications Management window, in the left navigation pane, select Security > Certificates.
2. On the Certificate Management page, select the Private Certificate Authority tab.
3. In the Private Certificate Authority Details section, click Download to save the contents of the certificate signed by the Primary Security Server to a file.
4. In the File Download–Security Warning dialog box, click Save to save the file to the local desktop.
Adding System Manager as a certificate authority
Procedure
1. From the Avaya Unified Communications Management window, in the left navigation pane, select Security > Certificates.
2. On the Certificate Management page, select the Certificate Endpoints tab.
118 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Generating a certificate on System Manager
3. Click the radio button associated with the IP address for the primary security server to view the certificate authorities associated with the system.
4. In the Certificate Authorities section, click Add.
The Certificate Authority Add Wizard is launched.
5. In the Add a CA to the Service window, in the Friendly Name field, enter a descriptive name for the System Manager.
6. Using a basic text editor application such as Microsoft
®
Notepad, open the PEM file
containing the System Manager certificate created in Exporting the System
Manager certificate on page 118.
7. Copy the entire contents of the file to the scrollable text box in the Add a CA to the
Service window.
Note:
For security purposes, the contents of the System Manager certificate file is not shown in the text box.
8. Click Submit.
9. In the Certificate Authorities section, verify System Manager was successfully added as a trusted certificate authority.
Generating a certificate on System Manager
About this task
Use this procedure to add a B5800 Branch Gateway End Entity to System Manager. This procedure adds the B5800 Branch Gateway to the System Manager trust domain and is required to establish a trust relationship between the B5800 Branch Gateway and System
Manager.
Procedure
1. From the System Manager console, under Services, select Security.
2. On the Security page, in the left navigation pane, select Certificates >
Authority.
3. In the left navigation pane, click Add End Entity.
4. On the Add End Entity page, do the following: a.
In the End Entity Profile drop-down box, select
INBOUND_OUTBOUND_TLS.
b.
In the Username field, enter the name of the B5800 Branch Gateway system.
c.
In the Password field, enter a certificate password.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 119
Initial branch configuration
Note:
This password will be used as the Simple Certificate Enrollment Protocol
(SCEP) password.
d.
In the Confirm Password field, enter the password again.
e.
In the CN, Common Name field, enter the appropriate name. This name should match the name of the B5800 Branch Gateway system you entered in the
Username field.
Note:
The certificate name cannot contain spaces.
f.
In the Certificate Profile drop-down box, accept the default setting,
ID_CLIENT_SERVER.
g.
In the CA drop-down box, accept the default setting, tmdefaultca.
h.
In the Token drop-down box, accept the default setting, User Generated.
i.
Click the Add End Entity button.
The page refreshes and a message appears at the top of the page stating the
End Entity was added successfully.
5. In the left navigation pane, click List/Edit End Entities.
6. On the List/Edit End Entities page, in the Or with status drop-down box, select
All.
7. Click the List button.
8. Confirm the B5800 Branch Gateway End Entity that you just added is listed.
Note that New appears in the Status column for this End Entity. This indicates
System Manager has prepared the certificate for exchange with an End Entity.
9. In the left navigation pane, click Public Web.
10. On the Welcome to the public EJBCA page, in the left navigation pane, click
Create Keystore.
11. On the EJBCA Certificate Enrollment page, in the Username field, enter the same username you entered when you created the End Entity in Step 4.
12. In the Password field, enter the same password you entered when you created the
End Entity in Step 4.
13. Click OK.
14. In the Options section, accept the default settings for the Key length and
Certificate profile fields, and click OK.
The certificate is installed in your browser.
15. In the Alert dialog box, click OK.
16. From your Firefox browser, to view the certificate, do the following: a.
Select Tools > Options.
b.
In the Options window, click Advanced.
120 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Using the Initial Installation Utility c.
Click the Encryption tab.
d.
Click the View Certificates button.
e.
In the Certificate Management window, click the Your Certificates tab.
17. From your Firefox browser, to save the certificate in the X.509 PEM format, do the following: a.
In the Certificate Management window, click the View button.
b.
In the Certificate Viewer window, click the Details tab.
c.
Click Export.
d.
In the Save Certificate to File window, in the Filename field, change the file name suffix to .cer. The .cer format is required for B5800 Branch Gateway.
e.
Click Save.
18. If you are not going to use the Initial Installation Utility, go to
Branch Gateway for certificates on page 124.
Using the Initial Installation Utility
About this task
The B5800 Branch Gateway Initial Installation utility provides a default configuration and security settings that minimize initial installation activities and maximize security. The system must be configured with the default settings before the system can be administered by Avaya
Aura
®
System Manager. This utility is used to enable System Manager administration of the
B5800 Branch Gateway.
Note:
For new installations, use the Initial Installation Utility before the control unit is connected to
the network. See Connecting the control unit to the network on page 88 for more information.
The Initial Installation Utility can be used to administer the control unit on site or while the
B5800 Branch Gateway control unit is being staged off site.
This procedure includes the steps to manually launch the Initial Installation utility. When a new
B5800 Branch Gateway is detected, the Initial Installation utility is launched automatically, so you would begin with Step 3.
Procedure
1. Start Manager and connect to the B5800 Branch Gateway system.
2. Select File > Advanced > Launch Initial Installation Utility.
3. In the System Name field, enter the appropriate system name.
4. For the WAN Interface, select LAN1 to connect to the enterprise network.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 121
Initial branch configuration
Warning:
You are also able to select LAN2 to connect to the enterprise network. However,
LAN2 is primarily intended to connect to the Internet or to public SIP trunks from carriers.
The LAN2 firewall is normally disabled. If you select LAN2 and choose to enable the firewall, be sure to open the necessary ports for communicating with the enterprise network. For more information, see
on page 277.
5. In the IP Address field, enter the appropriate IP address.
6. In the IP Mask field, enter the appropriate IP mask.
7. In the Gateway field, enter the appropriate gateway.
IP Office Manager will create an IP route using this gateway with the selected WAN as the destination.
8. In the DHCP Mode section, click the radio button for Disabled.
9. In the New Administrator Password field, enter a new administrator password.
10. In the New Security Password field, enter a new security password.
11. If you want the B5800 Branch Gateway to be managed by System Manager, check the Under Centralized Management? check box. Then complete the following fields.
a.
In the SMGR Address field, enter the IP address of the System Manager server.
b.
In the SNMP Community field, enter the appropriate SNMP community. This is the SNMP community for System Manager.
Note:
This field must be configured correctly in order for the centralized management functionality to work.
c.
In the SNMP Device ID field, enter the alarm ID you receive from a registration.
d.
In the Trap Community field, enter the appropriate trap community. This is the
SNMP community for the Secure Access Link (SAL) gateway.
Note:
This field must be configured correctly in order for the centralized management functionality to work.
The SNMPv1 trap community string can be set from the System Manager console under Services > Configurations > Settings > SMGR >
TrapListener. The trap community string in System Manager should match the trap community string set on the device so that System Manager receives the device alarms properly.
122 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Using the Initial Installation Utility e.
In the Device Certificate Name field, enter the appropriate certificate authority name.
Note:
The device certificate name cannot contain spaces.
f.
In the Certificate Enrollment (SCEP) Password field, enter the appropriate password.
12. Click Save.
The B5800 Branch Gateway reboots.
Result
When the B5800 Branch Gateway is administered by System Manager, the following is automatically configured:
• SNMP enabled
• SNMP trap destination 1 from System Manager IP address
• All SNMP traps active
• WebLM client active
• WebLM service address from System Manager IP address
• Remove all default extension users, leaving “NoUser” and “RemoteManager”
Additional features configured by the Initial Installation Utility
After you run the Initial Installation Utility, the following features are also configured:
• System Status Interface (SSA) service security level – Unsecure only
• Configuration service security level – Secure, Medium
• Security Administration service security level – Secure, Medium
• OAMP Web Services service security level – Secure, Low (if locally administered)
• OAMP Web Services service security level – Secure, High (if administered by System
Manager)
• Admin Client Certificate checks:-- High (if administered by System Manager)
• SCEP client active (if administered by System Manager)
• SCEP server IP address from SMGR IP address (if administered by System Manager)
• Legacy Program Code – Active (if locally administered)
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 123
Initial branch configuration
Configuring the B5800 Branch Gateway for certificates
Before you begin
Generate a certificate on System Manager. See Generating a certificate on System
on page 119.
About this task
Perform this procedure to configure the SCEP and security settings for a B5800 Branch
Gateway.
Note:
Perform this procedure only if you did not run the Initial Installation Utility. When you run the
Initial Installation Utility, the SCEP and security settings are automatically configured for the
B5800 Branch Gateway. See Using the Initial Installation Utility
on page 121 for more information.
Procedure
1. Start Manager and connect to the B5800 Branch Gateway system.
2. Select File > Advanced > Security Settings.
3. In the Select IP Office window, click the check box for the appropriate system.
4. Click OK.
5. In the Security Service User Login window, enter a user name and password of an account that has security configuration access to the B5800 Branch Gateway system.
The defaults are security and securitypwd.
6. In the Security Settings pane, click System.
7. Click the Certificates tab.
The certificate settings are set to the default values. The Issued to field shows the default certificate that resides on the B5800 Branch Gateway. The default value is the MAC address of the B5800 Branch Gateway system.
8. In the Identity Certificate section, click Delete to delete the default certificate.
9. In the Warning dialog box, click OK.
10. In the Default Certificate Name box, enter the appropriate name. This is the same name you used when you created the certificate for the End Entity in System
Manager. See
Generating a certificate on System Manager on page 119 for more
information.
11. In the Received Certificate Checks (Management Interfaces) drop-down box, accept the default setting, None.
124 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Configuring the B5800 Branch Gateway for certificates
12. In the Received Certificate Checks (Telephony Endpoints) drop-down box, accept the default setting, None.
13. In the SCEP Settings section, do the following: a.
Click the Active check box to select that option.
b.
In the Request Interval (Seconds) box, accept the default setting, 120.
c.
In the SCEP Server IP/Name field, enter the IP address of the System Manager server. Include https:// at the beginning of the IP address, for example https://123.4.567.89
.
d.
In the SCEP Server Port field, accept the default setting, 443.
e.
In the SCEP URI field, accept the default setting.
f.
In the SCEP Password field, enter the appropriate password. This is the same password you used when you created the certificate for the End Entity in System
Manager. See Generating a certificate on System Manager
on page 119 for more information.
g.
Click OK.
14. Click File > Save to save the security configuration.
15. From the System Manager console, do the following: a.
b.
In the left navigation pane, click List End Entities.
c.
Click the Reload button to reload the End Entity.
After the page refreshes, the status of the End Entity changes from New to
Generated. This indicates the End Entity certificate exchange has occurred.
16. In Manager, return to the Certificates tab. See Steps 1 to 7 above.
17. In the Received Certificate Checks (Management Interfaces) drop-down box, select Medium.
This ensures the B5800 Branch Gateway will enforce the use of certificates.
18. Click OK.
19. Click File > Save to save the security configuration.
20. Perform a synchronization. See
Synchronizing B5800 Branch Gateway with System
on page 164.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 125
Initial branch configuration
About adding B5800 Branch Gateways to System Manager
There are three different methods available that can be used to add B5800 Branch Gateways to System Manager. See one of the following topics:
•
Discovering B5800 Branch Gateways
on page 126. This method requires you to identify the subnet IP address in which each branch is located. This method does not automatically discover all B5800 Branch Gateways in a network.
•
Bulk importing of devices on page 128. This method requires you to manually add each
B5800 Branch Gateway to an xml file that is then used for bulk import to System
Manager.
•
Adding the B5800 Branch Gateways to System Manager
on page 130. This method requires you to manually add each branch to System Manager by identifying the IP address of the B5800 Branch Gateway.
Discovering B5800 Branch Gateways
Before you begin
Enable SNMP on the B5800 Branch Gateway to be updated. See
Enabling SNMP and polling support
on page 127.
About this task
Use this task to discover the B5800 Branch Gateways in the network and add them to System
Manager. This task requires that you identify the subnet IP address in which the branch is located. There is always one B5800 Branch Gateway per branch and each branch is in a different subnet. This procedure must be performed for each branch.
Procedure
1. From the System Manager console, under Elements, select Inventory.
2. On the Inventory page, select Inventory Management > Configuration.
3. On the Configuration page, click New.
4. On the Add SNMP Access Configuration page, in the Type drop-down box, select
V1.
5. In the Description field, enter a description to help identify this SNMP access configuration.
6. Set the Read Community field as configured on the device.
7. Set the Write Community field as configured on the device.
8. Accept the default settings in the Timeout (ms) and Retries fields.
126 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
About adding B5800 Branch Gateways to System Manager
9. Click Commit.
10. On the Configuration page, click the Subnets tab.
11. Click New.
12. On the Add Subnet Configuration page, in the Subnet IP field, enter the IP address of the subnet in which the branch is located.
13. In the Subnet Mask field, enter the subnet mask in which the branch is located.
14. In the Use SNMP V3 drop-down box, accept the default setting, No.
15. Under SNMP Access, click the check box(es) to select the appropriate SNMP access configuration(s).
16. Click Commit.
The new network appears in the list on the Configuration page.
17. On the left navigation page, under Inventory Management, click Collect
Inventory.
18. Under Select Network Subnet(s), click the check box(es) for the network subnets on which you want to discover B5800 Branch Gateways.
19. Under Select Device Types, click the check box for B5800 Branch Gateway.
20. Do one of the following:
• Click Now to run the inventory discovery job now.
• Click Schedule to run the inventory discovery job at a scheduled date and time.
When the job is completed, the B5800 Branch Gateway device(s) appear on the
Collected Inventory page and on the Upgrade Management > Manage Software page.
21. Repeat steps 11 to 20 for each branch that is to be managed from System
Manager.
Enabling SNMP and polling support
About this task
In order for the B5800 Branch Gateway control unit to be discovered and polled by an SNMP manager, its SNMP agent must be enabled and placed in the same read community as the
SNMP manager.
Procedure
1. Start Manager and connect to the B5800 Branch Gateway system.
2. In the left navigation pane, click System.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 127
Initial branch configuration
3. Click the System Events tab.
4. Select SNMP Enabled.
5. In the SNMP Port field, enter the UDP port number used by the SNMP agent to listen for and respond to SNMP traffic.
The default is 161.
6. In the Community (Read-only) field, enter the community to which the device belongs for read access.
This community name must match that used by the SNMP manager application when sending requests to the device. The community public is frequently used to establish communication and then changed (at both the SNMP agent and manager ends) for security.
7. Click OK.
8. Select File > Save Configuration to send the configuration back to the B5800
Branch Gateway and then select reboot.
After the reboot, the SNMP manager will be able to discover the control unit. The discovery includes the control unit type and the current level of core software.
Bulk importing of devices
Before you begin
Each B5800 Branch Gateway device has been added to an xml file. For information about the xml file containing the devices, see
About the xml file containing the B5800 Branch Gateway devices on page 129.
About this task
Use this task to import the B5800 Branch Gateway devices from an xml file to System
Manager.
Procedure
1. From the System Manager console, under Elements, select Inventory.
2. In the left navigation pane, click Manage Elements.
3. On the Manage Elements page, click More Actions > Import.
4. On the Import Elements page, in the Select File field, enter the complete path of the xml file. Or, click Browse to locate the xml file.
5. Select one of the following error configuration options:
• Abort on first error
• Continue processing other records
128 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
About adding B5800 Branch Gateways to System Manager
6. Select one of the following import options:
• To skip a matching record that already exists in the system during an import operation, click Skip.
• To replace all data for an application, click Replace.
• To merge application data so that you simultaneously perform an add and update operation of the application data, click Merge.
• To delete the application data from the database that match the records in the xml file, click Delete.
7. Select one of the following schedule job options:
• Click Run immediately to run the job now.
• Click Schedule later and then select the date and time to run the job at a scheduled date and time.
8. Click Import.
About the xml file containing the B5800 Branch Gateway devices
To use the bulk import method to add the B5800 Branch Gateways to System Manager, you must first manually add each B5800 Branch Gateway device to an xml file.
The following sample shows the contents of an xml file for one B5800 Branch Gateway device.
<?xml version=”1.0” ?>
<RTSElements xmlns="http://www.avaya.com/rts" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance">
<ApplicationSystems>
<ApplicationSystem name="B5800_2" isTrusted="false">
<Host ipaddress="192.168.42.2"></Host>
<ApplicationSystemType name="B5800 Branch Gateway" version="0"></ApplicationSystemType>
<Attributes>
<Attribute name="Is B5800 for Linux" value="false"></Attribute>
<Attribute name="Service Login" value="SMGRB5800Admin"></Attribute>
<Attribute name="Service Password" value="SMGRB5800Admin"></Attribute>
<Attribute name="Device version" value="6.2"></Attribute></Attributes>
</ApplicationSystem>
</ApplicationSystems>
</RTSElements>
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 129
Initial branch configuration
The fields for each B5800 Branch Gateway device that you add to the xml file will be the same except for the following two fields which contain unique information for each device:
• <ApplicationSystem name=”B5800 device”isTrusted=”false”> where B5800 device is a unique name for this system.
• <Host ipaddress=”IP address”></Host> where IP address is a unique IP address for this system.
Adding the B5800 Branch Gateways to System Manager
About this task
Use this procedure to manually add the B5800 Branch Gateways to System Manager. This procedure must be performed for each B5800 Branch Gateway.
Procedure
1. From the System Manager console, under Elements, select Inventory.
2. On the Inventory page, click Manage Elements.
3. On the Elements page, click New.
4. On the New Elements page, in the Type drop-down box, select B5800 Branch
Gateway.
5. On the New B5800 Branch Gateway page, in the Name field, enter a name for this
B5800 Branch Gateway.
6. In the Type drop-down box, select B5800 Branch Gateway.
7. In the Description field, enter a description to help identify this B5800 Branch
Gateway.
8. In the Node field, enter the IP address of the B5800 Branch Gateway.
9. Click the Attributes tab.
10. For the SNMP Attributes Version, click V1.
11. In the Read Community field, enter the community to which the device belongs for read access.
12. In the Write Community field, enter the community to which the device belongs for write access.
13. In the Service Password field, enter the service password. The default service password is the same as the Service Login (SMGRB5800Admin).
14. In the Confirm Service Password field, enter the service password again.
15. Click Commit.
130 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Enabling WebLM licensing for the branch
16. Repeat steps 3 to 15 for each branch that is to be managed from System
Manager.
Enabling WebLM licensing for the branch
About this task
If you are going to use WebLM licensing, you must enable the WebLM licensing feature for the branch. See
on page 16 for more information.
Procedure
1. From the System Manager console, select the B5800 Branch Gateway device and click Edit to edit the system configuration for the device. IP Office Manager will be launched on your PC. For more information, see
Editing a B5800 Branch Gateway system configuration from System Manager on page 159.
2. In the left navigation pane, click PLDS license.
3. Click the check box for Enable WebLM to select this option.
4. In the Domain Name (URL) field, enter the IP address or fully qualified domain name of the System Manager WebLM server or other WebLM server that is being used.
5. In the URN field, enter the name of the WebLM server. The default is WebLM/
LicenseServer.
6. In the Port Number field, use the up and down arrows to select the port number of the WebLM server. The default is 52233.
7. Click File > Save Configuration.
Creating a system template
About this task
System templates are designed for new systems. They are not designed to distribute edited system configurations to the branches. Distributing an edited system template to a branch would override any local configuration changes that were made to a specific branch.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 131
Initial branch configuration
Note:
An edited system template could be pushed to multiple branches if it is certain that the branches are identical, the modified system configuration applies to all the branches, and there are no local configuration changes that will be overwritten.
Procedure
1. From the System Manager console, under Services, select Templates.
2. On the Templates page, in the left navigation pane, click B5800 System
Configuration.
3. On the B5800 Branch Gateway System Configuration Templates page, do the following: a.
Under Supported B5800 Branch Gateway Types, click the check box for
B5800.
b.
Under Templates List, click New.
4. In the Name field, enter a name for this template.
5. In the System Type drop-down box, select B5800.
6. In the Version drop-down box, select the appropriate release.
7. To add more details to this system template, click Details.
IP Office Manager is launched.
8. Complete the fields as appropriate.
9. When finished, select File > Save Template and Exit.
Uploading an auto attendant audio file
About this task
You are able to upload and convert audio files to System Manager that can be used in the
B5800 Branch Gateway system configuration auto attendant feature. Once uploaded, from IP
Office Manager you are able to select the audio files from the Auto Attendant page.
Note:
If you are using a system template, you can add the audio file to the template to push the audio file down to multiple B5800 Branch Gateway systems.
Procedure
1. From the System Manager console, under Services, select Templates.
2. On the Templates page, click B5800 System Configuration.
132 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Applying the system template
3. On the B5800 Branch Gateway System Configuration Templates page, under
Templates List, select More Options > Manage Audio.
4. On the Manage Audio page, click the Browse button to locate the .wav file you want to upload.
5. Click the Upload button.
The voice file is uploaded to System Manager in the .c11 format that is required for
Embedded Voicemail on B5800 systems. The file is automatically converted from the .wav format to the .c11 format.
6. When finished, click the Done button.
Applying the system template
Procedure
1. From the System Manager console, under Services, select Templates.
2. On the Templates page, in the left navigation pane, click B5800 System
Configuration.
3. Under Supported B5800 Branch Gateway Types, click the check box for
B5800.
4. Click Show List.
All templates appear in the Templates List.
5. Select the template you want to apply, and then click Apply.
6. From the B5800 Branch Gateway Devices list, select the B5800 Branch Gateway(s) to which you want to apply the template.
7. Do one of the following:
• Click Now to run the job now.
• Click Schedule to run the job at a scheduled date and time.
Creating an endpoint template
Procedure
1. From the System Manager console, under Services, select Templates.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 133
Initial branch configuration
2. On the Templates page, in the left navigation pane, click B5800 Endpoint.
3. On the B5800 Branch Gateway Endpoint Templates page, do the following: a.
Under Supported B5800 Branch Gateway Types, click the check box for
B5800.
b.
Under Templates List, click New.
4. In the Name field, enter a name for this endpoint.
5. In the System Type drop-down box, select B5800.
6. In the Set Type drop-down box, select the appropriate set type.
7. In the Version drop-down box, select 6.2.
8. To configure more details for this endpoint, click the Details button.
The IP Office Manager applet is launched.
9. On the Warning – Security page, click the check box to Always trust content from
this publisher, and then click the Yes button.
Note:
After you select this check box for the first time, this warning page will no longer appear when you launch IP Office Manager.
10. On the Request Authentication page, click the OK button.
Note:
You do not need to provide a certificate on this page. This page will always appear when you launch IP Office Manager.
11. Complete the appropriate fields. The only fields you can edit in the user template are:
• Locale
• Priority
• System Phone Rights
• Profile
All other fields in the user template are non-editable because they are not applicable to multiple users.
12. When finished, select File > Save Template and Exit.
The template is saved in System Manager and listed in the Template List table.
134 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Disabling unused trunks
Disabling unused trunks
About this task
Each B5800 Branch Gateway trunk card provides a fixed number of trunk ports with digital trunk ports supporting a fixed number of digital channels. By default the B5800 Branch
Gateway configuration will have settings for all the possible trunks and channels.
In cases where the number of trunks or trunk channels in use is lower than the number supported by the trunk card, the unused trunks and channel must be disabled.
Important:
Failure to do this will cause problems with outgoing calls.
Procedure
1. From the System Manager console, select the B5800 Branch Gateway device and click Edit to edit the system configuration for the device. IP Office Manager will be launched on your PC. For more information, see
Editing a B5800 Branch Gateway system configuration from System Manager on page 159.
2. In the left navigation pane, click Line.
3. For each line, set those lines or channels that are not connected or not being used as Out of Service.
The location of the relevant setting varies for each trunk type.
4. For Analog Trunks, set the Trunk Type to Out of Service.
5. For BRI, E1 PRI, S0 and QSIG Trunks, set the channels quantities to match the actual subscribed channels.
6. For T1, T1 PRI and E1R2 Trunks, select the Channels tab. Then do the following:
Select those channels that are not used and click Edit.
• For T1 set the Type to Out of Service
• For T1 PRI set the Admin field to Out of Service.
• For E1R2 trunks set the Line Signalling Type to Out of Service.
7. Select File > Save Configuration.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 135
Initial branch configuration
Digital trunk clock source
About this task
Digital trunks require the telephone system at each end of the trunk to share a clock signal to ensure synchronization of call signalling. The B5800 Branch Gateway can obtain and use the clock signal from any of its digital trunks. Typically the clock signal provided by a digital trunk from the central office exchange is used as this will be the most accurate and reliable clock source.
To do this, the Clock Quality setting on each line in the B5800 Branch Gateway configuration is set to one of the following:
• Network
If available, the clock signal from this trunk should be used as the B5800 Branch Gateway clock source for call synchronization. If several trunk sources are set as Network, the
B5800 Branch Gateway will default to using one as detailed below.
• Fallback
If available, the clock signal from this trunk can be used as the clock source if none of the trunks set as Network are providing a clock source.
• Unsuitable
The clock source from this trunk will never be used as the B5800 Branch Gateway clock source.
If no clock source is available the B5800 Branch Gateway can use its own internal clock if necessary.
In the example below the first B5800 Branch Gateway is set to use the public network trunk as its clock source and ignoring the possible clock source from the QSIG trunk. The other
B5800 Branch Gateway system is using the clock signal received from the first B5800 Branch
Gateway on its QSIG trunk as its clock source. Thus both systems are using the same clock source and that clock source is the public network exchange.
When multiple trunks with the same setting are providing clock signals, trunks are used in the order of slots 1 to 4 and then by port on each slot.
The current clock source being used by an B5800 Branch Gateway system is shown on the
Resources page within the IP Office System Status Application.
136 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Digital trunk clock source
Setting a trunk clock quality setting
About this task
Procedure
1. From the System Manager console, select the B5800 Branch Gateway device and click Edit to edit the system configuration for the device. IP Office Manager will be launched on your PC. For more information, see
Editing a B5800 Branch Gateway system configuration from System Manager on page 159.
2. In the left navigation pane, click Line.
3. For each digital line, do the following: a.
Select the line.
b.
On the Line tab, select whether that trunk should provide the clock source for the network or whether the trunk is unsuitable.
Note:
For E1R2 trunks the Clock Quality setting is on the Advanced tab
4. Ensure that only one trunk is set to Network. This should preferably be a direct digital trunk to the central office exchange.
5. Set one other trunk to Fallback in case the selected network trunk connection is lost.
Note:
If possible this should be a trunk from a different provider since that reduces the chances of both sources failing at the same time.
6. Ensure that all other digital trunks are set as Unsuitable.
7. Select File > Save Configuration.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 137
Initial branch configuration
Setting the trunk prefixes
About this task
Where a prefix has been implemented for outgoing calls, that same prefix needs to be added to trunk settings. The prefix is then used as follows:
• On incoming calls the prefix is added to any incoming ICLID received with the call. That allows the ICLID to be used by B5800 Branch Gateway phones and applications to make return calls.
• On outgoing calls, the short codes used to route the call to a trunk must remove the dialing prefix.
Procedure
1. From the System Manager console, select the B5800 Branch Gateway device and click Edit to edit the system configuration for the device. IP Office Manager will be launched on your PC. For more information, see
Editing a B5800 Branch Gateway system configuration from System Manager on page 159.
2. In the left navigation pane, click Line.
3. For each line enter the prefix. The location of the relevant setting varies for each trunk type.
• For analog trunks, select the Line Settings tab and enter the prefix in the
Prefix field.
• For T1 and T1 PRI trunks, select the PRI 24 Line tab and enter the prefix in the Prefix field.
• For BRI, E1 PRI, and QSIG trunks, select the PRI Line tab and enter the appropriate prefix in the following fields:
- Prefix
- National Prefix
- International Prefix
4. Select File > Save Configuration.
SIP trunk prefixes
The prefix fields Prefix, National Prefix, Country Code and International Prefix are available with the SIP line settings. These fields are used in the following order:
138 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Setting the trunk prefixes
1. If an incoming number (called or calling) starts with the + symbol, the + is replaced with the International Prefix.
2. If the Country Code has been set and an incoming number begins with that Country
Code or with the International Prefix and Country Code, they are replaced with the
National Prefix.
3. If the Country Code has been set and the incoming number does not start with the
National Prefix or International Prefix, the International Prefix is added.
4. If the incoming number does not begin with either the National Prefix or International
Prefix, then the Prefix is added.
For example, if the SIP line is configured with the following prefixes, the numbers are processed as described in the table below.
• Line Prefix: 9
• National Prefix: 90
• International Prefix: 900
• Country Code: 44
Number Received
+441707362200
00441707362200
441707362200
6494770557
Processing
Following rule 1 above, the + is replaced with the
International Prefix (900), resulting in
900441707362200.
The number now matches the International Prefix (900) and Country Code (44).
Following rule 2 above they are replaced with the
National Prefix (90).
Resulting Number
901707362200
Following rule 2 above the
International Prefix (900) and the Country Code (44) are replaced with the National
Prefix (90).
90107362200
901707362200 Following rule 2 above, the
Country Code (44) is replaced with the National
Prefix (90).
Following rule 3 above the
International Prefix (900) is added.
9006494770557
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 139
Initial branch configuration
Administering a Session Manager line for each branch
This section provides the procedures required to configure a Session Manager line between each branch site and the headquarters site.
This section also describes how the B5800 Branch Gateway uses a configured Session
Manager line to handle incoming and outgoing calls to and from the branch and explains how a second Session Manager line can be configured for Session Manager line redundancy.
• See Enabling SIP trunk support on page 140. Use this procedure to configure the IP
Office LAN interface which will be used for the Session Manager line connection to the
Avaya Aura ® Session Manager.
• See Setting the branch prefix and local number length for extension numbering on
page 141. Use this procedure to set the prefix number for the B5800 Branch Gateway and the required extension length.
• See Changing the default codec selection
on page 144. Use this procedure to set the preferred order for codec negotiation. This can be done as a system default and also for each individual SIP and Avaya Aura ® Session Manager line.
• See Adding an Avaya Aura Session Manager line on page 146. Use this procedure to
create a Session Manager line for calls to the Avaya Aura
®
Session Manager.
• See Setting up outgoing call routing
on page 153. Use this procedure to create short codes for routing calls to the Avaya Aura ® Session Manager line when the required destination or resource is on another branch of the Avaya Aura ® network.
• See How the B5800 Branch Gateway uses a configured Session Manager line on
page 155.
• See Avaya Aura Session Manager line redundancy on page 152.
Enabling SIP trunk support
About this task
Before adding any SIP trunks, including Avaya Aura
®
Session Manager lines, the B5800
Branch Gateway system must be configured for SIP trunk operation. The system has 2 LAN interfaces, LAN1 and LAN2 (the physical ports are labeled LAN and WAN respectively). Either can be used for the Avaya Aura ® Session Manager line operation.
Important:
The configuration changes in the following procedure will require the B5800 Branch
Gateway system to be rebooted.
140 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Administering a Session Manager line for each branch
Procedure
1. From the System Manager console, select the B5800 Branch Gateway device and click Edit to edit the system configuration for the device. IP Office Manager will be launched on your PC. For more information, see
Editing a B5800 Branch Gateway system configuration from System Manager on page 159.
2. In the left navigation pane, click System.
3. Click the LAN1 or LAN2 tab as appropriate depending on which branch site LAN interface will be used for the data connection to the Avaya Aura ® network.
4. Confirm that the IP address and IP Mask fields are set correctly for the site.
5. Click the VoIP tab.
6. Select the SIP Trunks Enable option. This is required for Avaya Aura
®
Session
Manager trunk support.
Note:
The SIP Registrar Enable setting and settings in the SIP Registrar tab relate to
SIP extension support and therefore do not affect Avaya Aura
®
Session Manager lines. The settings in the Network Topology tab relate to external SIP trunks.
Those settings are not used by Avaya Aura ® Session Manager lines, which use open internet across the customer WAN.
7. Click OK.
8. Select File > Save Configuration.
The Send Configuration window appears and the Configuration Reboot Mode is set to Immediate. Do not change the reboot mode.
Setting the branch prefix and local number length for extension numbering
About this task
Each B5800 Branch Gateway system in the network should have a unique branch number.
That number is added as a prefix to the caller's extension number for calls routed from native extensions to the Avaya Aura
®
Session Manager. This means that native extensions are defined on the B5800 Branch Gateway without the branch prefix, so that when the branch prefix is added, the number is the correct length and format expected by Avaya Aura
®
Session
Manager.
The prefix is also used in the Avaya Aura
®
Session Manager configuration to create unique dial patterns for routing calls to the appropriate B5800 Branch Gateway.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 141
Initial branch configuration
Beginning in B5800 Branch Gateway R6.2, you have the option to leave the Branch Prefix field blank. If you do not configure the Branch Prefix, the native extensions must be defined with the full enterprise number. You are also able to leave the Local Number Length field blank.
By default B5800 Branch Gateway systems use 3-digit extension numbering starting from 200.
The existing allocated numbers can be changed in bulk using the Tools > Extension
Renumber option. This will add or remove a set value from all existing extension numbers in the configuration.
Procedure
1. From the System Manager console, select the B5800 Branch Gateway device and click Edit to edit the system configuration for the device. IP Office Manager will be launched on your PC. For more information, see
Editing a B5800 Branch Gateway system configuration from System Manager on page 159.
2. In the left navigation pane, click System.
3. Click the System tab.
4. Set the following fields as appropriate:
• Branch Prefix (optional)
• Local Number Length (optional)
• Proactive
• Reactive
These 4 fields are the key settings for B5800 Branch Gateway operation. See
on page 142 for more information.
5. Click OK.
6. Select File > Save Configuration.
The Send Configuration window appears and the Configuration Reboot Mode is set to Immediate. Do not change the reboot mode.
System tab field descriptions
Name
Branch Prefix
Range or Default
Range = 0 to 999999999
Description
This number is used to identify the B5800 Branch
Gateway system within the
Avaya Aura
®
network. The branch prefix of each B5800
Branch Gateway system must be unique and must not overlap. For example 85, 861
142 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Name
Local Number Length
Proactive
Reactive
Administering a Session Manager line for each branch
Range or Default Description and 862 are okay, but 86 and
861 overlap. On calls routed via an Avaya Aura
®
Session
Manager line, the branch prefix is added to the caller's extension number.
Beginning in B5800 Branch
Gateway R6.2, you have the option to leave the Branch
Prefix field blank. If you do not configure the Branch
Prefix, the native extensions must be defined with the full enterprise number.
Range = Blank (Off) or 3 to 9 for native extensions
This field sets the default length for extension numbers for extensions, users, and hunt groups added to the
B5800 Branch Gateway configuration. Entry of an extension number of a different length will cause an error warning by Manager.
The combined Branch
Prefix and Local Number
Length should not exceed
15 digits.
Beginning in B5800 Branch
Gateway R6.2, you have the option to leave the Local
Number Length field blank.
Default = 60 seconds,
Range = 60 to 100000 seconds
The B5800 Branch Gateway sends regular SIP OPTION messages to the Avaya
Aura
®
Session Manager line in order to check the status of the line. This setting controls the frequency of the messages when the Avaya
Aura
®
Session Manager line is currently in service.
Default = 60 seconds,
Range = 10 to 3600 seconds
The B5800 Branch Gateway sends regular SIP OPTION messages to the Avaya
Aura
®
Session Manager line in order to check the status of line. This setting controls the
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 143
Initial branch configuration
Name Range or Default Description frequency of the messages when the Avaya
Aura
®
Session Manager line is currently out of service.
Changing the default codec selection
About this task
By default, all B5800 Branch Gateway IP trunks and extensions use automatic codec negotiation. The default negotiation order is G729(a) 8K CS-ACELP, G711 U-Law 64K, G711
A-Law 64K, and G723.1 6K3 MP-MLQ. G.722 64K is also supported.
Note:
G.722 64K is not supported in B5800 Branch Gateway and CS 1000 deployments where
NRS is used for SIP interoperability.
If bandwidth between the B5800 Branch Gateway and CS 1000 sites is sufficient, change the first default preference to one of the G711 codecs. Note that the specific setting for individual branch trunks and extensions can be set to override the system setting if necessary.
Important:
The configuration changes in the following procedure will require the B5800 Branch
Gateway system to be rebooted.
Procedure
1. From the System Manager console, select the B5800 Branch Gateway device and click Edit to edit the system configuration for the device. IP Office Manager will be launched on your PC. For more information, see
Editing a B5800 Branch Gateway system configuration from System Manager on page 159.
2. In the left navigation pane, click System.
3. Click the Codecs tab.
4. In the Available Codecs section, check the appropriate codecs and move them to the Selected section.
The order of the codecs listed in the Selected section indicates the preferred codec order for trunks and extensions that are using automatic codec negotiation. See
Automatic codec preference settings
on page 145 for more information.
5. Click OK.
6. Select File > Save Configuration.
The Send Configuration window appears and the Configuration Reboot Mode is set to Immediate. Do not change the reboot mode.
144 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Administering a Session Manager line for each branch
Automatic codec preference settings
Setting
G.729
G.723
G.711 U-Law
G.711 A-Law
Selected
Preference
G729(a) 8K CS-
ACELP
G723.1 6K3 MP-
MLQ
2nd Preference 3rd Preference 4th Preference
G711 U-Law
64K
G729(a) 8K CS-
ACELP
G711 A-Law
64K
G711 U-Law
64K
G723.1 6K3 MP-
MLQ
G711 A-Law
64K
G711 U-Law
64K
G711 A-Law
64K
G711 A-Law
64K
G711 U-Law
64K
G729(a) 8K CS-
ACELP
G729(a) 8K CS-
ACELP
G723.1 6K3 MP-
MLQ
G723.1 6K3 MP-
MLQ
G.722 64K codec is also supported on systems with IP500 VCM or IP500 Combo cards. By default, the G.722 64K codec is not used.
Changing the maximum SIP sessions
About this task
The Maximum SIP Sessions setting determines the number of concurrent sessions allowed across all SIP trunks (SM line and public SIP trunks). Setting Maximum SIP Sessions to a specific value requires a corresponding quantity of B5800 Branch Gateway SIP Trunk Session licenses. If B5800 Branch Gateway cannot obtain the required license quantity then the configuration change will be rejected. If the required license quantity cannot be obtained or renewed for an already-configured value of Maximum SIP Sessions, then the B5800 Branch
Gateway will be in License Error mode, or in License Restricted mode if the 30-day grace period has expired. The license error can be resolved either by making a sufficient quantity of
SIP Trunk Session licenses available, or by reducing the configured Maximum SIP Sessions setting to a value for which sufficient license quantity is available. Regardless of the license mode, the number of concurrent SIP sessions allowed in system operation is determined by the Maximum SIP Sessions setting.
Procedure
1. From the System Manager console, select the B5800 Branch Gateway device and click Edit to edit the system configuration for the device. IP Office Manager will be launched on your PC. For more information, see
Editing a B5800 Branch Gateway system configuration from System Manager on page 159.
2. In the left navigation pane, click System.
3. Click the Telephony tab.
4. Click the Telephony sub-tab.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 145
Initial branch configuration
5. In the Maximum SIP Sessions box, click the up or down arrows to select the number that matches the Maximum SIP Trunk Sessions licensed for the system.
To see the Maximum SIP Trunk Sessions licensed for the system, in the left navigation pane, select PLDS License.
6. Click OK.
7. Select File > Save Configuration.
Adding an Avaya Aura
®
Session Manager line
About this task
Use this procedure to add an Avaya Aura ® Session Manager line to the B5800 Branch Gateway system configuration. If multiple Avaya Aura
®
Session Managers are available at the headquarters site, an additional Avaya Aura
®
Session Manager line can be added for Session
Manager line redundancy. The two Session Manager lines are prioritized based on the line number. The lower line number is considered the primary Session Manager line. Based on the priority of the Session Manager lines designated by the line number, the active line to which the B5800 Branch Gateway sends all calls will always be the highest priority Session Manager
on page 152 for more information.
Important:
The configuration changes in the following procedure will require the B5800 Branch
Gateway system to be rebooted.
Procedure
1. From the System Manager console, select the B5800 Branch Gateway device and click Edit to edit the system configuration for the device. IP Office Manager will be launched on your PC. For more information, see
Editing a B5800 Branch Gateway system configuration from System Manager on page 159.
2. In the left navigation pane, click Line.
3. Click the New icon and select SM Line.
4. Configure the line settings as appropriate. See Session Manager tab field descriptions
on page 147 for more information.
5. Click OK.
6. Click the VoIP tab.
7. Click the Re-Invite Supported check box to select this option.
8. Click the Allow Direct Media Path check box to select this option. You can select this option only if you selected Re-Invite Supported.
146 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Administering a Session Manager line for each branch
9. In the DTMF Support field, do the following:
• If CallPilot is configured as the voicemail system, accept the default setting,
RFC2833.
• If users will call into the Meeting Exchange conferencing server, select either
RFC2833 or Inband. Meeting Exchange does not support digit exchange through out-of band (that is, Info) signaling.
10. Configure the remaining fields as appropriate. See
VoIP tab field descriptions on
page 149 for more information.
11. Click OK.
12. Select File > Save Configuration.
The Send Configuration window appears and the Configuration Reboot Mode is set to Immediate. Do not change the reboot mode.
Session Manager tab field descriptions
Name
Line Number
In Service
SM Domain Name
SM Address
Description
This value is automatically assigned by
B5800 Branch Gateway and should be unique for each line added to the configuration.
The default setting is enabled. This option can be used to manually take the Session
Manager line out of service. It does not reflect or set the actual state of the line.
This name should match a SIP domain defined in the Session Manager system's
SIP Domains table. Unless there are reasons to do otherwise, all the B5800 Branch
Gateway systems in the CS 1000 network can share the same domain.
Note:
See Viewing the SIP domains on
page 168 for a list of SIP domains defined in Session Manager.
Enter the IP address of the Session Manager or NRS that the line should use in the CS
1000 network. The same Session Manager or NRS should be used for the matching
Entity Link entry in the CS 1000 configuration.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 147
Initial branch configuration
Name
Outgoing Group ID
Prefix
Max Calls
URI Type
Layer 4 Protocol
Send Port
Listen Port
Description
The default setting is 99999. This value is not changeable. However note the value as it is used in B5800 Branch Gateway short codes used to route calls to the Session Manager or NRS.
This field is blank by default. This prefix will be added to any source number received with incoming calls.
The default setting is 10. This value sets the number of simultaneous calls allowed between B5800 Branch Gateway and
Session Manager or NRS using this connection. Each call uses one of the available licenses that are shared by all SIP trunks configured in the system.
When SIP or SIPS is selected in the dropdown box, the SIP URI format is used (for example, [email protected]). This affects the From field of outgoing calls. The
To field for outgoing calls will always use the format specified by the short codes used for outgoing call routing. Recommendation:
When SIP Secured URI is required, the URI
Type should be set to SIPS. SIPS can be used only when Layer 4 Protocol is set to
TLS.
This can be set to TLS or TCP. Set to TLS to choose SIPS as the URI Type when SIP
Secured URI is required. For deployments that include NRS, set this field to TCP.
When Layer 4 Protocol is set to TLS, the default setting is 5061. When Layer 4
Protocol is set to TCP, the default setting is
5060.
When Layer 4 Protocol is set to TLS, the default setting is 5061. When Layer 4
Protocol is set to TCP, the default setting is
5060.
148 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Administering a Session Manager line for each branch
VoIP tab field descriptions
Name
Codec Selection
Fax Transport Support
Call Initiation Timeout
DTMF Support
Range or Default
Default = System Default
Default = None
Default = 4 seconds
Default = RFC2833
Description
This field defines the codec or codecs offered during call setup. When System Default is selected, the codec list shown matches the codecs set in the system-wide
Default Codec Selection
(System > Codecs).
This option is only selectable if the option Re-Invite
Supported is also selected.
If enabled, the B5800 Branch
Gateway is able to support the sending and receiving of faxes via the Avaya Aura
®
Session Manager line using the T38 protocol. The settings for T38 are set on the
T38 Fax tab.
The B5800 Branch Gateway sends regular OPTION messages to each Avaya
Aura
®
Session Manager line in order to check the lines in or out of service status. If a response is not received within this timeout, the line is treated as being out of service.
This setting is used to select the method by which DTMF key presses are signaled to the remote end. The supported options are In
Band, RFC2833 or Info.
• If CallPilot is configured as the voicemail system, accept the default setting,
RFC2833.
• If users will call into the
Meeting Exchange conferencing server, select
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 149
Initial branch configuration
Name
Media Security
Advanced
VoIP Silence Suppression
Allow Direct Media Path
Re-Invite Supported
Range or Default
Default = Disable
Default = Off
Default = On
Default = On
150 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
Description either RFC2833 or Inband.
Meeting Exchange does not support digit exchange through out-of band (that is, Info) signaling.
Media security is not required. All media sessions
(audio, video, and data) will be enforced to use RTP only.
This option provides additional media security options. These options are not supported in B5800
Branch Gateway R6.2.
When selected, this option will detect periods of silence on any call over the line and will not send any data during those silent periods.
This setting controls whether connected calls must remain routed via the B5800 Branch
Gateway or can be routed alternately if possible within the network structure.
• If enabled, connected calls can take routes other than through the B5800 Branch
Gateway. This removes the need for a voice compression channel.
• If disabled or not supported at one end of the call, the call is routed via the B5800
Branch Gateway. However
RTP relay support allows calls between devices using the same audio codec to not require a voice compression channel.
When enabled, Re-Invite can be used during a session to change the characteristics of
October 2012
Name
Use Offerer's Preferred
Codec
Codec Lockdown
Administering a Session Manager line for each branch
Range or Default
Default = Off
Default = Off
Description the session, for example when the target of an incoming call or a transfer does not support the codec originally negotiated on the trunk.
Normally for SIP calls, the codec preference of the answering end is used. This option can be used to override that behavior and use the codec preferences offered by the caller.
Supports RFC 3264 Section
10.2 when Re-Invite
Supported and Codec
Lockdown are enabled. In response to a SIP offer with a list of codecs supported, some SIP user agents supply a SDP answer that also lists multiple codecs. This means that the user agent may switch to any of those codecs during the session without further negotiation. The system does not support multiple concurrent codecs for a session, so loss of speech path will occur if the codec is changed during the session. If codec lockdown is enabled, when the system receives an SDP answer with more than one codec from the list of offered codecs, it sends an extra re-INVITE using just a single codec from the list and resubmits a new
SDP offer with just the single chosen codec.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 151
Initial branch configuration
Avaya Aura
®
Session Manager line redundancy
In an Avaya Aura ® network that includes multiple Avaya Aura ® Session Managers for redundancy, the B5800 Branch Gateway system can be configured with a secondary Avaya
Aura
®
Session Manager line. If for any reason the B5800 Branch Gateway system's primary
Avaya Aura ® Session Manager line goes out of service, the system will automatically attempt to use the secondary Avaya Aura ® Session Manager line. Prioritization of the Session Manager lines is determined by the line number configured for a particular Session Manager line. For example, if the first Session Manager line is configured with line number 17 and the second
Session Manager line is configured with line number 18, then line number 17 has the higher priority and is considered the primary Session Manager line. If for some reason you want to designate the secondary Session Manager line as the primary line, you must change one or both of the line numbers associated with the Session Manager lines so that the secondary
Session Manager line number is lower than that of the primary line.
The redundancy operation of the Session Manager lines is based on line prioritization. The active line to which B5800 Branch Gateway sends all calls is always the highest priority Session
Manager line in service. If the primary Session Manager line is in service, it is the active line for sending calls. If the connection to the primary Session Manager line is lost, causing B5800
Branch Gateway to switch to the secondary Session Manager line, when the primary line comes back up, B5800 Branch Gateway will switch back to the primary B5800 Branch Gateway line.
If all available channels of the current Avaya Aura ® Session Manager line are in use, the B5800
Branch Gateway will not overflow calls to the other Avaya Aura ® Session Manager line.
However, if PSTN trunk fallback has been configured, the other Avaya Aura
®
Session Manager line will be used. See
on page 296 for more information.
Avaya Aura ® Session Manager line service status checks
The B5800 Branch Gateway system sends regular SIP OPTIONS messages to any Avaya
Aura
®
Session Manager lines in its configuration. The Proactive and Reactive settings on the
B5800 Branch Gateway system's System tab set how often the SIP OPTIONS messages are sent in seconds. The Proactive setting is used for an Avaya Aura
®
Session Manager line currently thought to be in service. The Reactive setting is used for an Avaya Aura ® Session
Manager line currently thought to be out of service.
• If a response is received and is not a 408, 500, 503 or 504 response, the Avaya Aura
®
Session Manager line is treated as in service; otherwise the line is treated as being out of service.
• If no response is received within 32 seconds (SIP Timer F), the line is treated as being out of service.
• If the line is out of service, and call comes from the trunk, the trunks status is changed back to in service.
• If the line is in service, a call may fail due to either being unable to deliver the message or receive a 100 response within a configured timeout. The line will not go out of service because this may be a temporary failure due to a busy system.
152 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Administering a Session Manager line for each branch
Secondary Avaya Aura ® Session Manager line configuration
The secondary Avaya Aura
®
Session Manager line is configured in the same way as the primary Avaya Aura
®
Session Manager line. The only difference required is to set the SM
Address field to the address of the alternate Avaya Aura ® Session Manager from the one being used by the primary Avaya Aura
®
Session Manager line.
Setting up outgoing call routing
About this task
For calls from extensions on the B5800 Branch Gateway system to other numbers within the network, system short codes are used to route the calls to the Avaya Aura
®
Session Manager line. The Avaya Aura ® Session Manager then performs the routing to determine where the call should go.
Note:
See Branch PSTN call routing examples
on page 291 for information on routing back to the branch for fallback alternate routes.
Ideally the number of such system short codes should be kept to a minimum and the same short codes used on all branches in order to ease maintenance. This is where using a uniform dial plan for all branches helps, as explained in
Dial plan considerations on page 38. For our
example, the uniform dial plan allows the same single short code to be used at all branches.
See the Manager context-based help for more information on creating short codes.
Note:
In the Distributed branch user model, when a short code match occurs and the telephone number to be sent to the Avaya Aura
®
Session Manager line begins with the B5800 Branch
Gateway system's own branch prefix, the prefix is removed and the call is re-targeted locally on the B5800 Branch Gateway system.
Procedure
1. From the System Manager console, select the B5800 Branch Gateway device and click Edit to edit the system configuration for the device. IP Office Manager will be launched on your PC. For more information, see
Editing a B5800 Branch Gateway system configuration from System Manager on page 159.
2. In the left navigation pane, click Short Code.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 153
Initial branch configuration
3. Click the New icon and select Short Code.
4. Configure the settings as appropriate. See Short Code tab field descriptions on
page 154 for more information.
Note:
To view more information about the system short codes, press F1. In particular, see the description of the Dial short code.
5. Click OK.
6. Select File > Save Configuration.
Short Code tab field descriptions
Name
Code
Feature
Telephone Number
Line Group Id
Description
Enter the number dialed by users that should be matched to this short code. Use X wildcards for any single digit.
Leave this field set as Dial.
Set this field to match a number that should be passed to the Avaya Aura
®
Session
Manager for routing against its dialing pattern matches. The N wildcard can be used to match any wildcards in the Code.
Note:
Add SS to the entry in this field to have the caller ID passed to the Session Manager line. For example, if you are entering 8N in the Telephone Number field, enter
8NSS .
Set the Line Group ID to match the
Outgoing Group settings used in the SM lines URI setting.
154 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Name
Local
Force Account Code
Administering a Session Manager line for each branch
Description
Features that transfer the caller to Voicemail
Pro can indicate the language locale required for prompts. This is subject to the language being supported and installed on the voicemail server. The default is blank.
When selected, for short codes that result in the dialing of a number, the user is prompted to enter a valid account code before the call is allowed to continue. The default is Off.
How the B5800 Branch Gateway uses a configured Session
Manager line
Once configured and in operation, the Avaya Aura
®
Session Manager line is used as follows.
Outgoing calls from a branch
In the Distributed branch user model, if the outgoing call begins with the branch's own prefix, the prefix is removed and the call is targeted locally to the matching native user or hunt group extension number. If there is no matching extension number, the call is targeted to any matching system short code.
Incoming calls to a branch
Incoming calls on an Avaya Aura
®
Session Manager line are treated as being internal calls and do not go through the B5800 Branch Gateway system's Incoming Call Route settings.
• If the destination of the incoming call on the Avaya Aura ® Session Manager line starts with the system's branch prefix, the prefix is removed. The call is then targeted to the matching native user or hunt group extension number. If there is no matching extension number, the call is targeted to any matching system short code.
• If the destination of the incoming call on the Avaya Aura
®
Session Manager line does not start with the system's branch prefix, the whole number is checked for a match against system short codes.
Line status detection
The B5800 Branch Gateway system sends regular OPTION messages to any Avaya Aura
®
Session Manager lines in its configuration. The Proactive and Reactive settings on the B5800
Branch Gateway system's System tab set how often the OPTION messages are sent in seconds. The Proactive setting is used for an Avaya Aura
®
Session Manager line currently
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 155
Initial branch configuration thought to be in service. The Reactive setting is used for an Avaya Aura
®
Session Manager line currently thought to be out of service.
• If a response is received and is not a 408, 500, 503 or 504 response, the Avaya Aura
®
Session Manager line is treated as in service; otherwise the line is treated as being out of service.
• If the line is out of service, and call comes from the trunk, the trunks status is changed back to in service.
• If the line is in service, a call may fail due to either being unable to deliver the message or receive a 100 response within a configured timeout. The line will not go out of service because this may be a temporary failure due to a busy system.
• In addition each Avaya Aura ® Session Manager line can be manually set to in or out of service using the In Service option on the Avaya Aura
®
Session Manager line's Session
Manager tab.
Enabling branch SIP extension support
About this task
Before adding any SIP extensions, the B5800 Branch Gateway system must be enabled for
SIP extension support. Use this procedure to configure the B5800 Branch Gateway to support the addition of SIP extensions.
Important:
The configuration changes in the following procedure will require the B5800 Branch
Gateway system to be rebooted.
Procedure
1. From the System Manager console, select the B5800 Branch Gateway device and click Edit to edit the system configuration for the device. IP Office Manager will be launched on your PC. For more information, see
Editing a B5800 Branch Gateway system configuration from System Manager on page 159.
2. In the left navigation pane, click System.
3. Click the LAN1 or LAN2 tab, depending on which branch site LAN interface will be used for the SIP extensions.
4. In the LAN Settings tab, make a note of the IP Address and IP Mask details as these will be required during the SIP extension configuration.
5. Click the VoIP tab.
6. Check the SIP Registrar Enable check box. This is necessary for support of SIP extensions directly by the branch or when providing survivability support for Avaya
Aura ® SIP extensions.
7. Click OK.
156 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Enabling branch SIP extension support
8. Click the SIP Registrar tab.
9. Configure the fields on this tab as appropriate. See SIP Registrar tab field descriptions
on page 157 for more information.
10. Click OK.
11. Select File > Save Configuration.
The Send Configuration window appears and the Configuration Reboot Mode is set to Immediate. Do not change the reboot mode.
SIP Registrar tab field descriptions
Name
Domain Name
Layer 4 Protocol
Challenge Expiry Time
(sec)
Default
Default = Blank
Default = UDP, TCP, TLS
• UDP, SIP port = 5060
• TCP, SIP port = 5060
• TLS, SIP port = 5061
Default = 10
Description
This is the local SIP registrar domain name that will be needed by SIP devices in order to register with the
B5800 Branch Gateway. If this field is left blank, registration is against the
LAN IP address. For our examples we have been using a domain,
example.com.
If deploying centralized phones that will failover between the SIP Line
Gateway (SLG) and the
B5800 Branch Gateway, the
Domain Name must match that configured on the SLG at the main site.
This is the transport protocol for SIP traffic between the
B5800 Branch Gateway and
SIP extension devices.
The challenge expiry time is used during SIP extension registration. When a device registers, the SIP Registrar will send a challenge back to the device and waits for an appropriate response. If the
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 157
Initial branch configuration
Name Default Description response is not received within this timeout the registration is failed.
158 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Chapter 10: Managing B5800 Branch
Gateways from System
Manager
This chapter provides tasks that you will use as you configure B5800 Branch Gateways that are managed from System Manager.
Editing a B5800 Branch Gateway system configuration from
System Manager
Before you begin
Avaya Aura
®
System Manager has been set up to launch IP Office Manager. See
System Manager to launch IP Office Manager on page 111.
About this task
Use this procedure to launch IP Office Manager from System Manager to edit a B5800 Branch
Gateway system configuration.
Note:
You cannot configure users when editing a B5800 Branch Gateway system configuration from System Manager. User configuration is performed from System Manager User
Management. For more information, see
Restrictions when editing a B5800 Branch Gateway system configuration from System Manager
on page 160.
Procedure
1. From the System Manager console, under Elements, select B5800 Branch
Gateway.
2. In the left navigation pane, click System Configuration.
3. On the B5800 Branch Gateway System Configuration page, select the B5800
Branch Gateway device whose system configuration you want to edit.
4. Click Edit.
The IP Office Manager application is launched.
Note:
If the B5800AdminLite.exe file has not been downloaded to the System Manager server, an error message appears that says The system cannot find the file
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 159
Managing B5800 Branch Gateways from System Manager
specified. If you receive this message, click OK. Then see
Manager to launch IP Office Manager on page 111 for the procedure to install the
B5800AdminLite.exe file on the System Manager server.
Note:
If this is the first time you are attempting to edit a B5800 Branch Gateway device through System Manager from this PC, and IP Office Manager has not yet been installed on this PC, the following message appears:
B5800 Branch Gateway Manager not installed.
Avaya B5800 Branch Gateway Manager is not installed on this machine. To complete the current task, you must download and install Avaya B5800
Branch Gateway Manager. After you complete this installation restart the machine. Refer to the Release Notes/Online help.
Do you want to download Avaya B5800 Branch Gateway Manager from the server now?
If you receive this message, click Yes. Then go to step 4 in
Manager from the System Manager server to a PC on page 113 for the procedure
to install IP Office Manager on the PC.
Restrictions when editing a B5800 Branch Gateway system configuration from System Manager
When you edit the system configuration of a B5800 Branch Gateway device that is managed from System Manager, IP Office Manager is launched in system mode. The following restrictions apply when editing a B5800 Branch Gateway system configuration from System
Manager with IP Office Manager in system mode.
• Extension is visible in the Extn tab only but is disabled.
• All users (other than NoUser and RemoteManager) are visible in the User tab only but are disabled.
• NoUser has User and Source Number tabs visable and editable. The rest of the tab is not visable and therefore not editable.
• RemoteManager has the User tab visable and editable. The rest of the tab is not visable and therefore not editable.
The User Management feature available in System Manager is used to manage users and extensions on B5800 Branch Gateway systems that are centrally managed from System
Manager. See User administration
on page 187 for more information.
160 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
About disabling the System Manager administration feature for a B5800 Branch Gateway
Note:
Do not use IP Office Manager that is connected directly to the B5800 Branch Gateway device to edit users and extensions on systems that are centrally managed from System Manager.
Changes made to users and extensions in this way will not be synced back to System
Manager.
For more information about the two management methods, that is, central management from System Manager or local management from IP Office Manager, see
page 14. Do not use both of these management methods to configure and manage users and extensions on a B5800 Branch Gateway system.
System Manager does not support the configuration of User Rights on B5800 Branch Gateway systems. Similar functionality of applying selected user settings to groups of users is available from the System Manager user template capability.
About disabling the System Manager administration feature for a B5800 Branch Gateway
If the B5800 Branch Gateway is centrally managed by System Manager and you want to administer the B5800 Branch Gateway using IP Office Manager that is directly connected to the branch, for example to install an individual PLDS license file, you must first disable the
System Manager administration feature for the branch. Disabling the System Manager administration feature for a branch can be performed from System Manager or from IP Office
Manager if the network connection to System Manager is not available.
After you disable the System Manager administration feature for a branch and administer the branch using IP Office Manager, you must synchronize the B5800 Branch Gateway with
System Manager to synchronize the changes and return the System Manager administration feature for the branch to the enabled state. You can also manually enable the System Manager administration feature for a branch using either of the procedures listed below and clicking the check box for Under SMGR Administration to enable the feature.
To disable the System Manager administration feature for a branch, see one of the following:
•
Disabling the System Manager administration feature for the branch from System
•
Disabling the System Manager administration feature for the branch from IP Office
To synchronize the B5800 Branch Gateway with System Manager, see Synchronizing B5800
Branch Gateway with System Manager on page 164. Some configuration changes cannot be
synced with System Manager. See
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 161
Managing B5800 Branch Gateways from System Manager
Disabling the System Manager administration feature for the branch from System Manager
Procedure
1. From the System Manager console, under Elements, click B5800 Branch
Gateway.
2. On the B5800 Branch Gateway Element Management page, in the left navigation pane, click Security Configuration.
3. On the B5800 Branch Gateway Security Configuration page, click the radio button for the appropriate branch.
4. Click Edit.
5. In the Security Settings pane, select Services > Configuration.
6. In the Service Details tab, click the check box for Under SMGR Administration to deselect this option.
Note:
This check box is checked by default and you are not able to administer the branch through Manager. To be able to use Manager to administer the branch, this check box must be unchecked.
7. Click OK.
8. Select File > Save Configuration.
Disabling the System Manager administration feature for the branch from IP Office Manager
Procedure
1. Start IP Office Manager.
2. Select File > Advanced > Security Settings.
Note:
If the Security Settings option does not appear under Advanced, do the following: a. Select File > Preferences.
162 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
About disabling the System Manager administration feature for a B5800 Branch Gateway b. In the IP Office Manager Preferences dialog box, click the Set
Simplified View as default check box to deselect this option c. Click OK.
d. Close and restart IP Office Manager.
3. In the Select B5800 window, click the check box for the appropriate system.
4. Click OK.
5. In the Security Service User Login window, enter a user name and password of an account that has security configuration access to the B5800 Branch Gateway system.
The defaults are security and securitypwd.
6. In the Security Settings pane, select Services > Configuration.
7. In the Service Details tab, click the check box for Under SMGR Administration to deselect this option.
Note:
This check box is checked by default and you are not able to administer the branch through IP Office Manager. To be able to use IP Office Manager to administer the branch, this check box must be unchecked.
8. Click OK.
9. Select File > Save Security Settings.
Enabling the Security Settings option for the branch
About this task
To disable the System Manager administration feature for a branch that is centrally managed by System Manager, you must have access to the Security Settings for that branch. If the branch configuration has not yet been opened from IP Office Manager, the Security Settings option is not available. To enable the Security Settings option, you must de-select the Set
Simplified View as default option in the IP Office Manager Preferences window. Once that is done, the Security Settings option becomes available for that branch.
Note:
This task needs to be performed only one time.
Procedure
1. Start IP Office Manager.
2. Select File > Preferences.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 163
Managing B5800 Branch Gateways from System Manager
3. In the Preferences tab, click the Set Simplified View as default check box to deselect this option.
4. Click OK.
5. Close IP Office Manager.
6. See Disabling the System Manager administration feature for the branch from
on page 162.
Synchronizing B5800 Branch Gateway with System
Manager
About this task
more information.
Procedure
1. On the System Manager console, under Elements, click Inventory.
2. In the left navigation pane, click Synchronization > B5800 Branch Gateway.
3. Click the check box for the B5800 Branch Gateway system whose configuration you want to sync with System Manager.
4. Do one of the following:
• Click System Configuration to sync only system configuration data with
System Manager.
• Click User to sync only user data with System Manager.
• Click System Configuration and Users to sync system configuration and user data with System Manager.
5. Do one of the following: a.
Click Now to run the synchronization job now.
b.
Click Schedule to run the synchronization job at a scheduled date and time.
Configuration changes performed through Manager that cannot be synced with System Manager
You are able to disable System Manager administration for a B5800 Branch Gateway and configure the B5800 Branch Gateway device locally through IP Office Manager. To do this, you
164 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Synchronizing B5800 Branch Gateway with System Manager must first disable System Administration for the branch and then enable System Administration for the branch after you make your configuration changes. Then you must synchronize those changes with System Manager.
There are some configuration changes that cannot be synchronized with System Manager.
Those tasks should not be performed locally through IP Office Manager for branches that are centrally managed by System Manager. Configuration changes that cannot be synchronized and therefore should not be performed locally are:
• adding users or extensions
• editing user core attributes (that is, name, number, password, or extension number)
• changing any of the following security configuration settings:
- SMGRB5800Admin user settings
- SCEP settings
- certificates settings
- Web services settings
Also note that the User Rights feature is not integrated with System Manager. The User Rights feature is available only in the local IP Office Manager and is intended only for B5800 Branch
Gateways that are not configured to be managed centrally through System Manager.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 165
Managing B5800 Branch Gateways from System Manager
166 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Chapter 11: Session Manager
Configuration
This chapter provides procedures to configure Avaya Aura
®
Session Manager to support calls to and from
B5800 Branch Gateway systems. Avaya Aura
®
System Manager R6.2 is used to administer Session
Manager. Perform the following procedures:
1. View the SIP domains for which the Session Manager provides call management. Multiple
domains can be listed. See Viewing the SIP domains
on page 168.
2. Identify logical and/or physical locations where SIP entities reside. IP address patterns can be used to define different locations within the Avaya Aura
®
network, for example the IP address range of each B5800 Branch Gateway system. The creation of locations allows features such as bandwidth management to be applied to connections from those locations. See
on page 168.
3. Create a set of digit adaptations in order to ensure correct routing. If the digits to or from a branch need alteration in order to be routed correctly at either end, this can be done using a table of digit adaptations. Each SIP entity (branch) is associated with its own set of digit adaptations. See
on page 169.
4. Add each B5800 Branch Gateway system to the list of SIP entities that send calls to and from the Avaya Aura
®
network. See
on page 169.
5. Add an entity link for each SIP entity including each B5800 Branch Gateway. An entity link must be added to define the ports and transport method used for connections between the SIP entity and the Session Manager. See
Creating entity links on page 170.
6. Create time ranges to control when different routing policies are used. See
Creating time ranges on page 171.
7. Add a routing policy. A routing policy consists of a selected SIP entity as its destination and a number of time ranges that define when the policy can be used. See
on page 171.
8. Add dial patterns. Dial patterns are used to match digits received to a destination. Each dial pattern has an associated routing policy that defines the target entity for matched calls and
when the match should be used. See Creating dial patterns
on page 172.
Note:
You must complete fields marked with an asterisk. Fields not marked with an asterisk are optional.
For more information about administering Session Manager, see “Chapter 5: Managing Session Manager routing” in Administering Avaya Aura ® Session Manager, document number 03–603324.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 167
Session Manager Configuration
Viewing the SIP domains
The domain for which the Session Manager is authoritative was added when Session Manager was initially configured for the B5800 Branch Gateway system. The domain name set in the
B5800 Branch Gateway system's Session Manager line configuration (see Adding an Avaya
Aura Session Manager line on page 146) should match one of the entries that is listed on the
Domain Management page.
1. On the System Manager console, under Elements, click Routing.
2. In the left navigation pane, click Domains.
The SIP domains are listed on the Domain Management page.
Creating locations
Locations are used to identify logical and/or physical locations where SIP entities reside. The location entries in Session Manager allow bandwidth management and call control to be applied for connections to and from those locations.
Typically locations are added for each B5800 Branch Gateway branch site.
1. On the System Manager console, under Elements, click Routing.
2. In the left navigation pane, click Locations.
3. On the Location page, click New to add a new location.
4. On the Location Details page, in the Name field, enter a name to identify the location.
5. In the Notes field, enter notes about the location, as appropriate.
6. In the Managed Bandwidth Units field, accept the default setting.
7. In the Total Bandwidth field, accept the default setting, blank.
8. In the Multimedia Bandwidth field, accept the default setting, blank.
9. For the Audio Calls Can Take Multimedia Bandwidth check box, accept the default setting, checked.
10. In the Per-Call Bandwidth Parameters section, accept the default settings.
11. In the Alarm Threshold section, accept the default settings.
12. In the Location Pattern section, click Add to add a location pattern.
13. In the IP Address Pattern field, enter an IP address pattern that matches the IP
LAN address range.
168 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Creating adaptations
The * character can be used as a match-all wildcard. For example, the pattern
192.168.42.* matches all addresses in the range 192.168.42.1 to
192.168.42.255.
14. In the Notes field, enter notes about this location pattern, as appropriate.
15. Click Commit.
Creating adaptations
Occasionally calls to or from the branch may require digit conversion in order to ensure correct routing. For example, reinserting an external dialing prefix. This is done using a set of digit conversions stored by the digit adaptation associated with the SIP entity.
Adaptations are optional and are deployment specific. For more information, see “Adaptations” in “Chapter 5: Managing Session Manager routing” in Administering Avaya Aura ® Session
Manager, document number 03-603324.
Creating SIP entities
A SIP entity is required for each branch system. This is in addition to the SIP entities that should already exist for Session Manager and CS 1000.
1. On the System Manager console, under Elements, click Routing.
2. In the left navigation pane, click SIP Entities.
3. On the SIP Entities page, click New to create a new SIP Entity.
4. On the SIP Entity Details page, in the Name field, enter the name of the SIP entity.
5. In the FQDN or IP Address field, enter the IP address of the B5800 Branch
Gateway system LAN interface configured for the Session Manager line operation.
6. In the Type drop-down box, select SIP Trunk. SIP Trunk is the correct selection for branches deployed in the distributed branch user model.
7. In the Notes field, enter a description to help identify this SIP entity, as appropriate.
8. In the Adaptation drop-down box, select the adaptation that contains the digit conversions to apply to calls to and from the location.
9. In the Location drop-down box, select the location that matches the location you
configured in Creating locations on page 168.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 169
Session Manager Configuration
10. In the Time Zone drop-down box, select the time zone for the location.
11. For the Override Port & Transport with DNS SRV check box, accept the default setting, unchecked.
12. In the SIP Timer B/F (in seconds) field, accept the default setting, 4.
Note:
If you see that calls are abnormally terminated, you should increase this number.
13. In the Credential Name field, accept the default setting, blank.
14. In the Call Detail Recording field, accept the default setting.
15. In the SIP Link Monitoring drop-down box, accept the default, Use Session
Manager Configuration.
16. Click Commit.
Creating entity links
For each SIP entity communicating with the Avaya Aura
®
Session Manager, an entity link needs to be configured. That includes one for each B5800 Branch Gateway.
1. On the System Manager console, under Elements, click Routing.
2. In the left navigation pane, click Entity Links.
3. On the Entity Links page, click New.
4. In the Name field, enter a name to describe this link.
5. In the SIP Entity 1 drop-down box, select the name of the Session Manager system that is at one end of the link.
SIP Entity 1 must always be a Session Manager instance. For a Session Manager line from a B5800 Branch Gateway system, this should match the Session Manager set as the SM Address in the Session Manager line’s configuration.
6. In the Protocol drop-down box, select TCP.
When TCP is selected, the Port field is automatically set as 5060. This is the port to which the SIP Entity 2 sends SIP requests.
7. In the SIP Entity 2 drop-down box, select the name of the B5800 Branch Gateway system that is at the other end of the link.
When you selected TCP in the previous step, the Port field was automatically set as 5060.
8. Select the Trusted check box.
170 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Creating time ranges
This check box must be checked. If it is not checked, calls from the associated SIP
Entity 2 will be denied by Session Manager.
9. In the Notes field, enter notes regarding this entity link, as appropriate.
10. Click Commit.
Creating time ranges
Additional time ranges can be created and used with a routing policy to define when the routing policy is active. For most B5800 Branch Gateway implementations, you do not need to define additional time ranges. If you need to add or adjust a time range, see “Creating Time Ranges” in Administering Avaya Aura Session Manager, document number 03-603324.
Creating routing policies
A routing policy is a collection of multiple time ranges and a destination SIP entity. For each dial pattern configured to route calls received by the Session Manager, the routing policy associated with that dial pattern defines when and where matching calls are directed.
Separate routing policies are required for each B5800 Branch Gateway entity to which the
Session Manager routes calls.
1. On the System Manager console, under Elements, click Routing.
2. In the left navigation pane, click Routing Policies.
3. On the Routing Policies page, click New to create a new routing policy.
4. On the Routing Policies Details page, in the Name field, enter a name to describe this routing policy.
5. For the Disabled check box, accept the default, unchecked.
6. In the Notes field, enter notes about this routing policy, as appropriate.
7. In the SIP Entity as Destination section, do the following: a. Click Select.
b. On the SIP Entity List page, select the SIP entity to which the routing policy applies.
c. Click Select.
8. Skip the Time of Day section, Dial Patterns section, and Regular Expressions section. You do not need to configure these settings.
9. Click Commit.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 171
Session Manager Configuration
Creating dial patterns
A dial pattern is defined to direct calls prefixed with the branch prefix to each branch.
1. On the System Manager console, under Elements, click Routing.
2. In the left navigation pane, click Dial Patterns.
3. On the Dial Patterns page, click New to create a new dial pattern.
4. On the Dial Pattern Details page, in the Pattern field, enter the branch prefix.
This is the dialed number or number prefix that the dial pattern is intended to match.
5. In the Min field, enter the minimum length (1 to 36) of the dialed number that the pattern should match. For example, if the branch prefix is 3 digits and the extension number length is 4 digits, you would enter 7.
6. In the Max field, enter the maximum length (1 to 36) of the dialed number that the pattern should match. For example, if you set this to the same value as the Min value, the dial pattern will match only internal calls.
7. For the Emergency Call check box, leave the check box set to the default setting, unchecked.
8. In the SIP Domain drop-down box, select the appropriate SIP domains that should be matched, or select All to allow calls from all SIP domains to be routed.
9. In the Notes field, enter notes to describe this dial pattern, as appropriate.
10. In the Originating Locations and Routing Policies section, click Add.
11. In the Originating Location section, click the check box for Apply The Selected
Routing Policies to All Originating Locations.
12. In the Routing Policies section, click the check box for the routing policy that was created for the branch.
13. Click Select.
14. If you need to specify that calls from certain locations be denied, do the following: a. In the Denied Originating Locations section, click Add.
b. Do one of the following:
• Click the Apply to All Originating Locations check box.
• Click the check box(es) for the locations that should be denied.
c. Click Select.
15. On the Dial Patterns Detail page, click Commit.
172 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Chapter 12: Voicemail configuration
This chapter provides the procedures to configure the voicemail system that the B5800 Branch Gateway will use. If Embedded Voicemail or Standalone Voice Mail are configured, see one of the following documents for information on how to configure user mailboxes, hunt group mailboxes, and auto attendants:
• Implementing Embedded Voicemail for B5800 Branch Gateway Release 6.2, document number
18-604098
• Implementing Standalone Voice Mail for B5800 Branch Gateway Release 6.2, document number
18-604088
Note:
Standalone Voice Mail must be installed on a separate Linux server.
Voicemail options
The B5800 Branch Gateway system uses its Embedded Voicemail by default. However, a number of other voicemail options are supported.
• Embedded Voicemail — Embedded Voicemail uses the system SD card in the B5800
Branch Gateway system control unit for storage of prompts and messages. Embedded
Voicemail supports mailboxes for all local extension numbers, announcements to waiting callers, and auto attendants (up to 40) for external calls. Its capacity is limited to 15 hours of recorded messages, prompts and announcements. Embedded Messaging Port licenses must be purchased with sufficient quantity to support the configured number of ports.
• Standalone Voice Mail — Standalone Voice Mail provides additional port capacity provided on a Linux server. You must have a Linux server installed to use this option.
When you select this option, you must enter the IP address of the Linux server where
Standalone Voice Mail is installed. This option provides a maximum capacity of 40 ports while the Embedded Voicemail option provides a maximum capacity of 6 ports.
Embedded Messaging Port licenses must be purchased with sufficient quantity to support the configured number of ports.
• Avaya Aura Messaging — The B5800 Branch Gateway system can be configured to use Avaya Aura Messaging as its voicemail server when Session Manager is used as the
core SIP router. See Configuring B5800 Branch Gateway to use Avaya Aura Messaging for voicemail
on page 177 for more information. When Avaya Aura Messaging is used as the central voicemail system, at each branch you have the option to still use the local
Embedded Voicemail or Standalone Voice Mail for auto attendant operation and for
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 173
Voicemail configuration announcements to waiting calls. Note that for this configuration, Embedded Voicemail licenses are required.
• CallPilot — The B5800 Branch Gateway system can be configured to use CallPilot as its voicemail server when Session Manager is used as the core SIP router. See
Configuring B5800 Branch Gateway to use CallPilot for voicemail on page 179 for more
information. When CallPilot is used as the central voicemail system, at each branch you have the option to still use the local Embedded Voicemail or Standalone Voice Mail for auto attendant operation and for announcements to waiting calls. Note that for this configuration, Embedded Voicemail licenses are required.
For more information about licensing, see Licensing on page 16.
Configuring Embedded Voicemail
About this task
Embedded Voicemail is the default voicemail configuration for B5800 Branch Gateway.
Procedure
1. From the System Manager console, select the B5800 Branch Gateway device and click Edit to edit the system configuration for the device. IP Office Manager will be launched on your PC. For more information, see
Editing a B5800 Branch Gateway system configuration from System Manager on page 159.
2. In the left navigation pane, click System.
3. Click the Voicemail tab.
4. In the Voicemail Type drop-down box, select Embedded Voicemail.
Note:
Fields applicable to this mode of voicemail support are enabled. If the field is not applicable, the field is disabled.
5. If you want the users to be presented with a display menu for access to their mailbox, check the Messages Button Goes to Visual Voice check box. For more information, see the IP Office Manager on-line help.
6. In the Minimum Password Length field, use the up and down arrows to set the appropriate minimum password length.
7. In the Maximum Record Time field, use the up and down arrows to set the maximum record time in seconds for recorded announcement and auto attendant prompts. messages and prompts.
8. In the VoiceMail ports field, use the up and down arrows to set the number of voicemail ports. This field must match the number of voicemail ports that are licensed for the system.
174 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Configuring Standalone Voice Mail
9. In the Reception/Breakout (DTMF 0) drop-down box, select the number to which a caller is transferred if they press 0 while listening to the mailbox greeting rather than leaving a message. Do one of the following: a.
To configure Park and Page for this DTMF breakout, select Park & Page and then do the following: i. In the Paging Number drop-down box, select the appropriate hunt group or user extension.
ii. In the Retries field, use the up and down arrows to set the number of times to repeat the page.
iii. In the Retry timeout field, use the up and down arrows to set the amount of time to elapse before the page is repeated. The time is set in 15–second increments.
b.
To configure Centrex Transfer for this DTMF breakout, select Centrex Transfer and then enter the transfer number in the Transfer Number field.
c.
To configure an extension number for this DTMF breakout, select the appropriate extension number from the Reception/Breakout (DTMF 0) dropdown box.
Note:
You can also enter an external number in this field.
10. For the Breakout (DTMF 2) drop-down box, repeat step 9.
11. For the Breakout (DTMF 3) drop-down box, repeat step 9.
12. In the SIP Name field, enter the appropriate name.
13. In the SIP Display Name (Alias) field, enter the appropriate name.
14. In the Contact field, enter the appropriate name.
15. Configure the Anonymous check box as appropriate. This feature is enabled when this check box is selected.
Note:
For more information about the fields in the SIP Settings section, see the IP Office
Manager on-line help.
Configuring Standalone Voice Mail
About this task
The B5800 Branch Gateway system can be configured to use Standalone Voice Mail.
Standalone Voice Mail provides additional port capacity provided on a Linux server. Before you perform this procedure, Standalone Voice Mail must be installed and configured on the
Linux server. The Standalone Voice Mail server and required Linux operating system
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 175
Voicemail configuration components are provided on the IP Office Applications DVD. For more information, see
Implementing Standalone Voice Mail for the Avaya B5800 Branch Gateway, document number
18-604088.
Procedure
1. From the System Manager console, select the B5800 Branch Gateway device and click Edit to edit the system configuration for the device. IP Office Manager will be launched on your PC. For more information, see
Editing a B5800 Branch Gateway system configuration from System Manager on page 159.
2. In the left navigation pane, click System.
3. Click the Voicemail tab.
4. In the Voicemail Type drop-down box, select Standalone Voice Mail.
Note:
Fields applicable to this mode of voicemail support are enabled. If the field is not applicable, the field is disabled.
5. If you want the users to be presented with a display menu for access to their mailbox, check the Messages Button Goes to Visual Voice check box. For more information, see the IP Office Manager on-line help.
6. In the Voicemail IP Address field, enter the IP address of the Linux server where
Standalone Voice Mail is installed.
7. In the Minimum Password Length field, use the up and down arrows to set the appropriate minimum password length.
8. In the Maximum Record Time field, use the up and down arrows to set the maximum record time in seconds for recorded announcement and auto attendant prompts.
9. In the VoiceMail ports field, use the up and down arrows to set the number of voicemail ports. This field must match the number of voicemail ports that are licensed for the system.
10. In the Reception/Breakout (DTMF 0) drop-down box, select the number to which a caller is transferred if they press 0 while listening to the mailbox greeting rather than leaving a message. Do one of the following: a.
To configure Park and Page for this DTMF breakout, select Park & Page and then do the following: i. In the Paging Number drop-down box, select the appropriate hunt group or user extension.
ii. In the Retries field, use the up and down arrows to set the number of times to repeat the page.
176 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Configuring B5800 Branch Gateway to use Avaya Aura Messaging for voicemail iii. In the Retry timeout field, use the up and down arrows to set the amount of time to elapse before the page is repeated. The time is set in 15–second increments.
b.
To configure Centrex Transfer for this DTMF breakout, select Centrex Transfer and then enter the transfer number in the Transfer Number field.
c.
To configure an extension number for this DTMF breakout, select the appropriate extension number from the Reception/Breakout (DTMF 0) dropdown box.
11. For the Breakout (DTMF 2) drop-down box, repeat step 10.
12. For the Breakout (DTMF 3) drop-down box, repeat step 10.
13. In the SIP Name field, enter the appropriate name.
14. In the SIP Display Name (Alias) field, enter the appropriate name.
15. In the Contact field, enter the appropriate name.
16. Configure the Anonymous check box as appropriate. This feature is enabled when this check box is selected.
Note:
For more information about the fields in the SIP Settings section, see the IP Office
Manager on-line help.
Configuring B5800 Branch Gateway to use Avaya Aura
Messaging for voicemail
About this task
The B5800 Branch Gateway system can be configured to use Avaya Aura Messaging as its voicemail server.
Note:
If Avaya Aura Messaging is used as the central voicemail system, you are able to still use the local Embedded Voicemail or Standalone Voice Mail for auto attendant operation and for announcements to waiting calls.
Procedure
1. From the System Manager console, select the B5800 Branch Gateway device and click Edit to edit the system configuration for the device. IP Office Manager will be launched on your PC. For more information, see
Editing a B5800 Branch Gateway system configuration from System Manager on page 159.
2. In the left navigation pane, click System.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 177
Voicemail configuration
3. Click the Voicemail tab.
4. In the Voicemail Type drop-down box, select Avaya Aura Messaging.
Note:
Fields applicable to this mode of voicemail support remain enabled.
5. To enable the local B5800 Branch Gateway system features for Embedded
Voicemail auto attendants and announcements, in the Use embedded for AA and
Announcements drop-down box, select the appropriate embedded voicemail. The announcements are those that the callers hear when the call in on hold.
Note:
You must also enable the announcements. Do this by selecting the check box for
Announcements On which appears when you select Hunt Group >
Announcements tab and Users > Announcements tab.
6. In the AAM Number field, enter the extension number configured for mailbox access to the Avaya Aura
®
Messaging system. Note that this number is automatically routed via the active Avaya Aura
®
Session Manager line. It does not need to be routed through the normal branch call routing.
7. In the AAM PSTN Number field, enter the PSTN number to which you want to reroute attempts to access mailboxes when the Avaya Aura ® Session Manager line(s) are out of service. (This field is optional.)
When calls to access voicemail are routed by this method, the calls go through the
PSTN trunk that is configured on the B5800 Branch Gateway.
Note:
The PSTN voicemail number requires a corresponding Short Code entry so that the calls are routed to the correct line during rainy-day operation.
8. For the Enable Voicemail Instructions Using DTMF check box, do one of the following: a.
To send the voicemail instructions as DTMF tones, ensure the Enable
Voicemail Instructions Using DTMF check box is selected (that is, checked).
When this check box is selected, the voicemail mail box number of the recipient and the appropriate digit(s), such as # or ## that are used to leave or collect a message, are automatically sent as DTMF tones so the caller does not need to enter those digits.
b.
To require the caller to dial the user's voicemail mail box to send the required
DTMF digits, do not select this check box (that is, the check box is not checked).
The capability to turn this feature off is provided because there may be networks where the DTMF digits may not correctly reach the messaging system due to a provider's network characteristics. When this feature is turned off, the DTMF
178 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Configuring B5800 Branch Gateway to use CallPilot for voicemail digits are not automatically sent. Instead, the caller will dial the user's mail box number to manually send the required DTMF digits to access the mailbox.
9. In the Maximum Record Time field, use the up and down arrows to set the maximum recording length in seconds for recorded announcement and auto attendant prompts.
Note:
You can set a number in this field only if you selected one of the two voicemail options in the Use embedded for AA and Announcements drop-down box.
10. In the VoiceMail Ports field, use the up and down arrows to set the number of licensed voicemail ports.
Note:
You can set a number in this field only if you selected one of the two voicemail options in the Use embedded for AA and Announcements drop-down box.
Avaya Aura Messaging requires SIP Trunk Session configuration and uses SIP
Trunk Sessions licenses.
11. Accept the default setting (on, that is check box is checked) for Enable Voicemail
Instructions Using DTMF.
12. Click OK.
13. Select File > Save Configuration.
The Send Configuration window appears and the Configuration Reboot Mode is set to Immediate. Do not change the reboot mode.
Configuring B5800 Branch Gateway to use CallPilot for voicemail
About this task
The B5800 Branch Gateway system can be configured to use CallPilot as its voicemail server.
Note:
CallPilot and CS 1000 can be configured to send Message Waiting Indication (MWI) in a
SIP NOTIFY message to the B5800 Branch Gateway user. For more information, see
Configuring CallPilot and CS 1000 to send MWI in a SIP NOTIFY message to the user
on page 181.
Procedure
1. From the System Manager console, select the B5800 Branch Gateway device and click Edit to edit the system configuration for the device. IP Office Manager will be
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 179
Voicemail configuration launched on your PC. For more information, see
Editing a B5800 Branch Gateway system configuration from System Manager on page 159.
2. In the left navigation pane, click System.
3. Click the Voicemail tab.
4. In the Voicemail Type drop-down box, select Call Pilot.
Note:
Fields applicable to this mode of voicemail support remain enabled.
5. To enable the local B5800 Branch Gateway system features for Embedded
Voicemail auto attendants and announcements, in the Use embedded for AA and
Announcements drop-down box, select the appropriate embedded voicemail. The announcements are those that the callers hear when the call in on hold.
Note:
You must also enable the announcements. Do this by selecting the check box for
Announcements On which appears when you select Hunt Group >
Announcements tab.
6. In the Phone Context field, enter the appropriate number, up to a maximum of 11 characters. This number is the CDP or UDP dial plan configured on CS 1000. This number is included in the history information field of the SIP message to identify the
CallPilot mail box.
7. In the Call Pilot Number field, enter the extension number configured for mailbox access to the Call Pilot system. Note that this number is automatically routed via the active Avaya Aura ® Session Manager line or the NRS SIP line. It does not need to be routed through the normal branch call routing.
Note:
The Call Pilot PSTN Number field and associated Enable Voicemail
Instructions Using DTMF check box are disabled in R6.2. B5800 Branch
Gateway does not access the CallPilot system over the PSTN when the Session
Manager line is down.
8. In the Maximum Record Time field, use the up and down arrows to set the maximum recording length in seconds for recorded announcement and auto attendant prompts.
Note:
You can set a number in this field only if you selected one of the two embedded voicemail options in the Use embedded for AA and Announcements dropdown box.
9. In the VoiceMail Ports field, use the up and down arrows to set the number of licensed voicemail ports.
10. Accept the default setting for Enable Voicemail Instructions Using DTMF.
180 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Configuring B5800 Branch Gateway to use CallPilot for voicemail
Note:
The Enable Voicemail Instructions Using DTMF check box and associated
Call Pilot PSTN Number field are disabled in R6.2. B5800 Branch Gateway does not access the CallPilot system over the PSTN when the Session Manager line is down.
11. Click OK.
12. Select File > Save Configuration.
The Send Configuration window appears and the Configuration Reboot Mode is set to Immediate. Do not change the reboot mode.
Configuring CallPilot and CS 1000 to send MWI in a SIP NOTIFY message to the user
About this task
To configure CallPilot and CS 1000 to send Message Waiting Indication (MWI) in a SIP NOTIFY message to the B5800 Branch Gateway user, the configuration described below must be performed. For more information, see CS 1000 System and CallPilot Server Configuration, document number NN44200–312.
Procedure
1. Configure B5800 Branch Gateway as a satellite site on CallPilot.
2. Enable MWI DN and Message waiting indication options for the B5800 Branch
Gateway user on CallPilot.
3. Configure DCH on CS 1000 with RCAP MWI as follows:
ADAN DCH 11
CTYP DCIP
DES VTRK
USR ISLD
ISLM 4000
SSRC 3700
OTBF 32
NASA YES
IFC SL1
CNEG 1
RLS ID 25
RCAP ND2 MWI TAT
MBGA NO
H323
OVLR NO
OVLS NO
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 181
Voicemail configuration
Modular Messaging and Avaya Aura Messaging PSTN
Fallback
When the branch is configured to use Modular Messaging over SIP or Avaya Aura Messaging for its voicemail services, that configuration includes setting an internal Modular Messaging or
Avaya Aura Messaging number (800700 for the following example) for calls to Modular
Messaging or Avaya Aura Messaging which are automatically routed via the Session Manager line.
An additional Modular Messaging or Avaya Aura Messaging PSTN number can also be configured for use when the Session Manager line is not in service (915553800701 for the following example). However, it may also require additional configuration to ensure that this number is correctly routed to a branch PSTN trunk. That could be done using a system short code, but doing it in the ARS form keeps all the branch PSTN call routing in one place for ease of maintenance.
Adding an overriding short code
Procedure
1. From the System Manager console, select the B5800 Branch Gateway device and click Edit to edit the system configuration for the device. IP Office Manager will be launched on your PC. For more information, see
Editing a B5800 Branch Gateway system configuration from System Manager on page 159.
2. In the left navigation pane, click ARS.
182 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
3. Click 50: Main.
Adding an overriding short code
Within the ARS form, the default 1N; short code is the one used for national calls.
It would match the MM PSTN Number or AAM PSTN Number and attempt to route it to the SM Line which we know is out of service if the MM PSTN Number or AAM
PSTN Number is being used for calls to voicemail. We can change the routing by adding a specific short code for the MM PSTN Number or AAM PSTN Number.
4. To add a short code, click the Add... button.
5. Make the changes as follows: a.
In the Code field, set this to match the external PSTN number for Modular
Messaging or Avaya Aura Messaging without the external dialing prefix.
b.
In the Feature drop-down box, select Dial3K1.
c.
In the Telephone Number field, set this to N to match the whole number in the
Code field.
Note:
For a setup where the voicemail mail box numbers configured on Modular
Messaging or Avaya Aura Messaging are the same as the caller's DID, the short code to route the PSTN call should be configured so that the caller ID is withheld. To do this, enter a W in the Telephone Number field of the short code. This ensures that during rainy-day operation, the voicemail system does not automatically go to the voicemail mail box of the caller based on the caller ID.
d.
In the Line Group Id drop-down box, select the line group ID being used for the branch's PSTN trunks. The default is 0.
6. Click OK.
The ARS now has two short codes that will potentially match external national calls.
However, one is a more exact match for certain calls and therefore will be applied
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 183
Voicemail configuration to those calls.
7. Click OK.
8. Select File > Save Configuration.
Uploading an auto attendant audio file
About this task
You are able to upload and convert audio files to System Manager that can be used in the
B5800 Branch Gateway system configuration auto attendant feature. Once uploaded, from IP
Office Manager you are able to select the audio files from the Auto Attendant page.
Note:
If you are using a system template, you can add the audio file to the template to push the audio file down to multiple B5800 Branch Gateway systems.
Procedure
1. From the System Manager console, under Services, select Templates.
2. On the Templates page, click B5800 System Configuration.
3. On the B5800 Branch Gateway System Configuration Templates page, under
Templates List, select More Options > Manage Audio.
4. On the Manage Audio page, click the Browse button to locate the .wav file you want to upload.
184 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Uploading an auto attendant audio file
5. Click the Upload button.
The voice file is uploaded to System Manager in the .c11 format that is required for
Embedded Voicemail on B5800 systems. The file is automatically converted from the .wav format to the .c11 format.
6. When finished, click the Done button.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 185
Voicemail configuration
186 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Chapter 13: User administration
This chapter provides the procedures to add distributed users to B5800 Branch Gateway and Avaya Aura ®
System Manager.
Adding distributed users to System Manager
About this task
When you add a distributed user to System Manager, you must configure a B5800 Branch
Gateway Profile on System Manager.
Procedure
1. On the System Manager console, under Users, click User Management.
2. In the left navigation pane, click Manage Users.
3. On the User Management page, click New.
4. On the New User Profile page, in the Identity section, do the following: a.
In the Last Name field, enter the user's last name.
Note:
Depending on how the branches and stations in your system are named and organized, you could enter a location name in this field, for example Chicago
25 . Then in the next field, First Name, you could enter a location within that branch, for example cashier.
b.
In the First Name field, enter the user's first name.
c.
In the Middle Name field, enter the user's middle name.
d.
In the Description field, enter a description of this user profile.
e.
In the Login Name field, enter the extension user login in the format, [email protected] or [email protected]. For example, [email protected] or [email protected].
For survivability mode operation with a B5800 Branch Gateway system, the user name without the domain name should match the user name configured in the branch system.
f.
In the Authentication Type drop-down box, accept the default setting,
Basic.
g.
In the Password field, enter the password required to log into System Manager for personal web configuration.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 187
User administration h.
In the Confirm Password field, enter the password again.
i.
In the Localized Display Name field, enter the name to be used as the calling party.
j.
In the Endpoint Display Name field, enter the user's full name.
k.
In the Title field, enter the user's title if applicable.
l.
In the Language Preference drop-down box, select the appropriate language.
m. In the Time Zone drop-down box, select the user's time zone.
n.
In the Employee ID field, enter the user's employee ID.
o.
In the Department field, enter the user's department.
p.
In the Company field, enter the name of the user's company.
q.
To add a postal address for this user, do the following: i. Expand the Address section.
ii. Click New.
iii. On the Add Address page, complete the fields as appropriate.
r.
To add multiple phone numbers for this user, do the following: i. Expand the Phone Details section.
ii. Complete the fields as appropriate.
iii. Click Add.
5. To specify a localized language, expand the Localized Names section, and do the following: a.
In the Language drop-down box, select the language for displaying the user name.
b.
In the Display Name field, enter the user's name.
c.
Click Add.
6. To add a TDM or IP endpoint, or a distributed SIP endpoint, such as an 11xx/12xx
SIP phone, click the Communication Profile tab.
7. Accept the default values for the Communication Profile Password field, Confirm
Password field, Name field, and Default check box.
8. Click the B5800 Branch Gateway Endpoint Profile check box, and do the following: a.
In the System drop-down box, select the appropriate system.
b.
Check the Use Existing Extension check box if there is an available extension that you want to assign to this user.
When you select this check box, if there are unassigned extensions, a dropdown box appears from which you can select an unassigned extension to assign to this user.
c.
In the Extension field, enter the appropriate extension.
d.
In the Template drop-down box, select the appropriate template.
188 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Editing the B5800 Branch Gateway Endpoint Profile for a user
When you select a template, the Set Type field is automatically populated based on the template selected.
e.
To change other parameters such as call appearances or feature buttons for this user, click the Endpoint Editor button and do the following: i. Update the fields as appropriate.
ii. Click Save to save your changes.
iii. Click Exit to exit the Endpoint Editor.
This updates parameters for this user. The changes are not reflected in the template.
Note:
Parameters for this user can also be configured using the endpoint template.
See Creating an endpoint template
on page 133 for more information.
f.
For the Delete Extension On User Delete check box, do one of the following:
• Accept the default, unchecked, if you are using an analog or digital set type template and this feature is checked for other set types.
• Select this check box if you want the extension to be deleted when the extension is unassigned or the communication profile is deleted.
9. Click Commit.
A distributed user is added on the B5800 Branch Gateway and is associated with a user in System Manager.
10. Repeat this procedure for each distributed user you want to add.
Editing the B5800 Branch Gateway Endpoint Profile for a user
About this task
Use this procedure to edit a B5800 Branch Gateway Endpoint Profile for a distributed user.
Procedure
1. On the System Manager console, under Users, click User Management.
2. In the left navigation pane, click Manage Users.
3. From the list of users on the User Management page, select the user you want to edit.
4. Click Edit.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 189
User administration
5. Click the Communication Profile tab to expand that section.
6. Expand the Communication Address section.
7. Expand the B5800 Branch Gateway Endpoint Profile.
8. To change the extension for this user, in the Extension field enter the appropriate extension.
9. To apply a different template to this user, in the Template drop-down box, select the appropriate template.
10. To change other parameters for this user, click the Endpoint Editor button.
IP Office Manager is launched where you can edit data for this user.
11. Update the fields as appropriate.
12. Click Save.
You return to the edit user window in System Manager.
13. Click Commit.
190 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Chapter 14: Managing license files with
PLDS
PLDS Overview
The Avaya Product Licensing and Delivery System (PLDS) provides customers, Avaya
Partners, distributors, and Avaya Associates with tools for managing license entitlements and electronic delivery of software and related license files. Using PLDS, you can perform operations such as license activations, license upgrades, license moves, and software downloads.
Installation software packages for Avaya products are available as ISO files on PLDS. Users can download the ISO images to a PC, and choose to either burn a DVD for installation or transfer the ISO file to the target server for installation.
Note:
The B5800 Branch Gateway R6.2 administrator applications are provided on DVD. They are not available for download from PLDS. However, once available, you will be able to download B5800 Branch Gateway R6.2 Service Packs from PLDS.
You can check PLDS to determine if a later service pack or software release is available. If updates do exist, see the appropriate upgrade procedures, contact Avaya, or contact the Avaya
Partner Service representative.
When you place an order for a PLDS-licensed software product, the license entitlements on the order are automatically created in PLDS. Once these license entitlements are created, you receive an e-mail notification from PLDS. This e-mail notification includes a license activation code (LAC). Using the LAC, you can quickly find and activate the newly purchased license entitlements in PLDS. You can then download the license file.
Important:
You must provide the WebLM host ID to activate the license file in PLDS. The primary
WebLM host ID is the MAC address of a physical network interface card (NIC) on the server.
If you are not using WebLM to manage the licenses, you must provide the host ID of each
B5800 Branch Gateway in your network to generate a license for each branch. The host ID is the Feature Key Serial Number printed on the B5800 Branch Gateway System SD card.
For more information, see Licensing
on page 16.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 191
Managing license files with PLDS
Examples of license management tasks that you can perform in PLDS include:
• Adding more license entitlements to an existing activation
• Upgrading a license file to a new major release
• Moving license entitlement activations between license hosts
• Regenerating a license file with an new host ID
Registering for PLDS
Procedure
1. Go to the Avaya Product Licensing and Delivery System (PLDS) Web site at https:// plds.avaya.com
.
The PLDS Web site redirects you to the Avaya single sign-on (SSO) Web page.
2. Log in to SSO with your SSO ID and password.
The PLDS registration page is displayed.
3. If you are registering:
• as an Avaya Partner, enter the Partner Link ID. If you do not know your Partner
Link ID, send an e-mail to [email protected].
• as a customer, enter one of the following:
- Company Sold-To
- Ship-To number
- License authorization code (LAC)
4. Click Submit.
Avaya will send you the PLDS access confirmation within one business day.
About license activation
What is license activation?
License activation is a process of activating license entitlements by specifying a license host and host ID of the WebLM server. The process includes generating the license file.
Note:
If you are not using WebLM to manage the licenses, you must provide the host ID of each
B5800 Branch Gateway in your network to generate a license for each branch. The host ID
192 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
About license activation is the Feature Key Serial Number printed on the B5800 Branch Gateway System SD card.
For more information, see Licensing
on page 16.
When license entitlements are activated, PLDS generates Activation Records containing the activation information and License/Key.
Types of license activation
Types of activation include:
• Regular activation: where license entitlements are activated to generate Activation
Records.
• Upgrade activation, which involves either:
- Activating license entitlements that have been marked as upgradeable. When you activate these license entitlements, you can generate License/Key for either the current version or the old version.
- Activating upgrade license entitlements, which are purchased to upgrade other existing license entitlements. When users activate these license entitlements, they select the license entitlements to upgrade.
Activating license entitlements
Before you begin
You know the Host ID of the License Host if you are activating license entitlements on a new
License Host.
About this task
Use the License Activation Code (LAC) to activate one or more license entitlements. You can activate all of the licenses, or you can specify a number of licenses to activate from the quantity available. Upon successful activation of the license entitlements, PLDS creates an Activation
Record and sends an Activation Notification e-mail message to the customer who is registered with the entitlements. The Activation Record and Activation Notification provide details on the number of activated licenses and the License Host. The license file can be accessed on the
License/Keys tab of the Activation Record in PLDS and is also an attachment to the Activation
Notification e-mail message. You must install the license file on WebLM to use the licenses.
Note:
If you are not using WebLM to manage the licenses, you must install the license file on each
B5800 Branch Gateway to use the licenses. For more information, see Licensing on page
16.
Procedure
1. Type http://plds.avaya.com
in your Web browser to access the Avaya PLDS
Web site.
2. Enter your Login ID and password to log on to the PLDS Web site.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 193
Managing license files with PLDS
3. In the LAC(s) field of the Quick Activation section, enter the LAC that you received in an e-mail message.
Note:
If you do not have an e-mail message with your LAC, follow the steps in the
Searching for Entitlements section and make a note of the appropriate LAC from the LAC column.
Note:
The Quick Activation automatically activates all license entitlements on the LAC.
However, you can remove line items or specify a number of licenses to activate from the quantity available.
4. Enter the License Host information.
You can either create a new license host or use an existing license host.
5. Click Next to validate the registration detail.
6. Enter the License Host Information.
The Host ID is the MAC address of the server hosting the WebLM server. The Host
ID is obtained from the Server Properties page of the WebLM server where the license file will be installed.
Note:
If you are not using WebLM to manage the licenses, you would enter the Host ID of the B5800 Branch Gateway. This is the Feature Key Serial Number printed on the System SD card. You must add dashes between pairs of digits to provide the number in MAC address format (nn-nn-nn-nn-nn-nn). You can also get the Host
ID from Manager. For more information, see
7. Enter the number of licenses to activate.
8. Review the Avaya License Agreement and accept the agreement if you agree.
9. Perform the following steps to send an activation notification e-mail message: a.
In the E-mail to field, enter e-mail addresses for any additional activation notification recipients.
b.
Enter any comments or special instructions in the Comments field.
c.
Click Finish.
10. Click View Activation Record.
• The Overview tab displays a summary of the license activation information.
• The Ownership tab displays the registration information.
• The License/Key tab displays the license files resulting from the license activation. In general, a single license file will be generated for each application. From the License/Key tab, you can view and download the license
194 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Searching for license entitlements file. Install each license file on the WebLM server associated with the License
Host.
Note:
For B5800 Branch Gateway, when using WebLM to manage licensing, a single license file is generated for all B5800 Branch Gateways in the multiple branches. A single license file is not generated for each branch or application. If you are not using WebLM to manage the licenses, individual license files are installed on a single branch at a time, where the branch is
the License Host. For more information, see Licensing
on page 16.
Searching for license entitlements
About this task
Use this functionality to search for an entitlement by using any one or all of the following search criteria:
• Company name
• Group name
• Group ID
• License activation code
In addition to these search criteria, PLDS also provides other additional advanced search criteria for searching license entitlements.
Note:
Avaya associate or Avaya Partners can only search license entitlements by company name.
Procedure
1. Type http://plds.avaya.com
in your Web browser to access the Avaya PLDS
Web site.
2. Enter your Login ID and password to log on to the PLDS Web site.
3. Click Assets > View Entitlements.
The system displays Search Entitlements page.
4. To search license entitlements by company name, enter the company name in the
%Company: field. To see a complete list of companies before searching for their corresponding entitlements, do the following: a.
Click the magnifying glass icon.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 195
Managing license files with PLDS b.
Enter the name or several characters of the name and a wildcard (%) character.
c.
Click Search Companies.
d.
Select the desired company name from the list of options.
Tip:
You can use a wildcard (%) character if you do not know the exact name of the company you are searching for. For example, if you enter Av%, the system searches for all the company names starting with the letter Av. You can enter a wildcard character at any position in the search criteria.
5. To search license entitlements by group name, enter the appropriate information in the %Group name: or %Group ID: fields.
Group Names or IDs are specific to Functional Locations and Sold-To’s that define the actual location of equipment and software.
Tip:
You can use a wildcard character if you do not know the exact name of the group you are searching for. For example, if you enter Gr%, the system searches for all the groups starting with the characters Gr. You can enter a wildcard character at any position in the search criteria.
6. To search license entitlements by LAC, enter the specific LAC in the %LAC: field.
Tip:
You can use a wildcard character if you do not know the exact LAC you are searching for. For example, if you enter AS0%, the system searches for all the
LACs starting with AS0. You can enter a wildcard character at any position in the search criteria.
You will receive LACs in an e-mail if you have supplied the e-mail address to your sales order. If you do not have this code, search by using one of the other search criteria.
7. To search license entitlements by application, product or license status, select the appropriate application, product, and/or status from the field.
8. Click Search Entitlements.
Result
All corresponding entitlement records appear at the bottom of the page.
196 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Moving activated license entitlements
Moving activated license entitlements
Before you begin
Host ID or License Host name of the move from/to License Host.
About this task
Use this functionality to move activated license entitlements from one License Host to another.
You can chose to move all or a specified quantity of license entitlements.
Note:
If you move a specified number of activated license entitlements from one host to another by using the Rehost/Move transaction in PLDS, two new license files are generated:
• One license file reduces the number of license entitlements on the License Host from which you are moving license entitlements.
• One license file increases the number of license entitlements on the License Host to which you are moving license entitlements.
Install each of these license files on the appropriate server.
If you move all activated license entitlements, only one license file is generated. Install this new license file on the License Host to which you are moving license entitlements. Remove the license file from the License Host from which you are moving all license entitlements.
Procedure
1. Type http://plds.avaya.com
in your Web browser to access the Avaya PLDS
Web site.
2. Enter your Login ID and password to log on to the PLDS Web site.
3. Click Activation > Rehost/Move from the Home page.
4. Click View Activation Record information to find and select licenses to rehost or move.
You can search the activation records by the Company name, license host, Group name or ID using the Search Activation Records functionality.
Note:
If you are an Avaya associate or Avaya Partner, enter the search criteria and click
Search Activation Records.
5. Select Rehost/Move for the License Host from which you are moving license entitlements.
6. In the Search License Hosts field, enter the License Host to which you are moving license entitlements.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 197
Managing license files with PLDS
Alternatively, you can click Add a License Host to select an existing License
Host.
7. Validate the Registration Detail and click Next.
8. Enter the License Host Information.
The Host ID is the MAC address of the server hosting the WebLM server. The Host
ID is obtained from the Server Properties page of the WebLM server where the license file will be installed.
Note:
If you are not using WebLM to manage the licenses, you would enter the Host ID of the B5800 Branch Gateway. This is the Feature Key Serial Number printed on the System SD card. You must add dashes between pairs of digits to provide the number in MAC address format (nn-nn-nn-nn-nn-nn). You can also get the Host
ID from Manager. For more information, see
9. Enter the number of Licenses to move in the QTY column field and click Next.
10. Accept the Avaya Legal Agreement.
11. Perform the following steps to send an activation notification e-mail message: a.
In the E-mail to field, enter e-mail addresses for any additional activation notification recipients.
b.
Enter any comments or special instructions in the Comments field.
c.
Click Finish.
12. Click View Activation Record.
• The Overview tab displays a summary of the license activation information.
• The Ownership tab displays the registration information.
• The License/Key tab displays the license files resulting from the license activation. In general, a single license file will be generated for each application. From the License/Key tab, you can view and download the license file. Install each license file on the WebLM server associated with the License
Host.
Note:
For B5800 Branch Gateway, when using WebLM to manage licensing, a single license file is generated for all B5800 Branch Gateways in the multiple branches. A single license file is not generated for each branch or application. If you are not using WebLM to manage the licenses, individual license files are installed on a single branch at a time, where the branch is
the License Host. For more information, see Licensing
on page 16.
198 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Regenerate License files
Regenerate License files
Use this functionality to regenerate the license file on a selected License Host. During the regeneration process, you can only modify host ID information.
Regenerating a license file
Procedure
1. Type http://plds.avaya.com
in your Web browser to access the Avaya PLDS
Web site.
2. Enter your Login ID and password to log on to the PLDS Web site.
3. Click Activation > Regeneration from the Home page.
4. Search License Activations to Regenerate.
You can search the activation records by the Company name, license host, Group name or ID using the Search Activation Records functionality.
5. Click Regenerate from the appropriate record.
6. Validate the Registration Detail and click Next.
7. Validate the items that will regenerate and click Next.
8. Accept the Avaya Legal Agreement.
9. Perform the following steps to send an activation notification e-mail message: a.
In the E-mail to field, enter e-mail addresses for any additional activation notification recipients.
b.
Enter any comments or special instructions in the Comments field.
c.
Click Finish.
10. Click View Activation Record.
• The Overview tab displays a summary of the license activation information.
• The Ownership tab displays the registration information.
• The License/Key tab displays the license files resulting from the license activation. In general, a single license file will be generated for each application. From the License/Key tab, you can view and download the license file. Install each license file on the WebLM server associated with the License
Host.
Note:
For B5800 Branch Gateway, when using WebLM to manage licensing, a single license file is generated for all B5800 Branch Gateways in the multiple
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 199
Managing license files with PLDS branches. A single license file is not generated for each branch or application. If you are not using WebLM to manage the licenses, individual license files are installed on a single branch at a time, where the branch is
the License Host. For more information, see Licensing
on page 16.
200 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Chapter 15: Standalone SAL Gateway for remote service
Avaya Client Services (ACS) uses the Secure Access Link (SAL) Gateway to provide remote delivery of service to the B5800 Branch Gateway. The supported configuration requires a standalone SAL gateway that is deployed in the enterprise headquarters/data center and using the B5800 Branch Gateway administration applications — Manager, System Status, and System Monitor. See
Administration software suite on page 79 for a description of these applications.
SAL Gateway R2.1 software must be installed on a customer-provided server in the enterprise at a central location that allows for network connectivity to each deployed branch. The SAL solution is fully customer controlled through the deployment and use of the optional SAL policy server.
Note:
SAL Gateway does not support alarming for B5800 Branch Gateway managed devices in CS 1000 deployments.
Note:
System Platform's Virtual SAL Gateway (VSALGW) is not supported in managing each individual branch. The VSALGW is only officially supported by Avaya in management of system platform “onboard” devices such as System Platform, Session Manager and System Manager. Each B5800 Branch
Gateway branch is considered an “off-board” device.
Use of SAL to access the B5800 Branch Gateway administration tools and System Manager
You are able to access the B5800 Branch Gateway administration tools and Avaya Aura ®
System Manager through SAL.
• Manager
Manager is an administration tool used to configure and upgrade the B5800 Branch
Gateway system. You can use Manager to administer each branch individually. You are able to use SAL to access the Manager application for local or remote configuration management of the B5800 Branch Gateway system.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 201
Standalone SAL Gateway for remote service
Note:
For B5800 Branch Gateway upgrades and Embedded File Management, you must access Manager that is installed on a PC that resides within the customer network.
• System Status Application
System Status is an administration tool used to monitor the current status of individual branches in the B5800 Branch Gateway system. You are able to use SAL to access the
System Status Application that is installed locally or remotely.
• System Monitor (Tier3/4 tool only)
System Monitor is an administration tool that provides detailed traces of all activity on the
B5800 Branch Gateway system.
Note:
You are able to use SAL to access the System Monitor application that is installed on a PC that resides within the customer network.
• Avaya Aura System Manager
System Manager is a central management system that delivers a set of shared management services and a common console for System Manager and its components.
System Manager provides a single access interface to administer multiple branch locations and multiple distributed or centralized B5800 Branch Gateway users.
For more information about the B5800 Branch Gateway administration tools and System
Manager, see
Administration software suite on page 79.
SAL Gateway installation and registration
To install SAL Gateway, see Chapter 2 in Secure Access Link 2.1, SAL Gateway
Implementation Guide, document number 146775, which is available on the Avaya support
Web site http://support.avaya.com
. The Secure Access Link 2.1 Gateway software download is also available on the Avaya support Web site.
Registering a product with Avaya is a process that uniquely identifies the device so that Avaya can service it. A SAL Gateway registration form is provided with your software download. See
Universal Install/SAL Registration Request Form
on page 204 for more information. To register the SAL Gateway, complete Step 1 on the form and send it to [email protected]. The following information is requested in Step 1:
• Your company name
• Avaya Sold-to Number (customer number)
• Your contact information, so that Avaya can contact you if there are questions
202 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
B5800 Branch Gateway registration and SAL Gateway on-boarding
Avaya uses this information to register your gateway. When the registration is complete, Avaya will send you an e-mail that provides the following information:
• The Solution Element ID and Product ID numbers
• A list of the devices currently registered at this location
• A list of other locations for your company
Note:
Optional: If you want to get Solution Element IDs (SEID) from other locations, complete the
Step 2 tab of the registration sheet and send it to [email protected] using the link included on the sheet. Avaya will send you a list of SEIDs from the locations you selected.
B5800 Branch Gateway registration and SAL Gateway onboarding
Each B5800 Branch Gateway deployed must be registered with Avaya. To add managed devices to your SAL Gateway using the Solution Element IDs (SEID) provided to you during
SAL Gateway registration described above, see “Managed element configuration” in Chapter
4 in the Secure Access Link 2.1, SAL Gateway Implementation Guide, document number
146775, which is available on the Avaya support Web site.
When you have added all your managed devices, complete Step 2 of the SAL Gateway registration form for each managed device you added to your SAL Gateway and send the form to [email protected]. When this form is received, the Avaya registration team makes the appropriate changes to allow access to your managed devices through the SAL Gateway.
Avaya will then confirm via an e-mail notification that remote access to your product has been enabled through your SAL Gateway.
B5800 Branch Gateway SAL-based alarming
The SAL Gateway supports alarming for the B5800 Branch Gateway managed device. You must change the alarm destination on your B5800 Branch Gateway managed device so that alarms are routed to your centralized SAL Gateway. See
information. During the registration and on-boarding process of each branch, the Avaya registration team also tests alarming through the SAL Gateway and back into Avaya alarm receivers.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 203
Standalone SAL Gateway for remote service
Universal Install/SAL Registration Request Form
You can download this form from the Avaya support web site as follows:
1. Go to the Avaya support Web site http://support.avaya.com
.
2. Select More Resources > Equipment Registration.
3. Under Non-Regional (Product) Specific Documentation, select Universal
Install/SAL Registration Request Form.
4. Complete the registration form as instructed.
204 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Chapter 16: Additional system procedures
This chapter provides procedures for ongoing maintenance and management of your system, such as system shutdown and reboot, replacing components, and system backup.
Changing the IP address settings
About this task
Use this procedure to change the system name, IP address, IP mask, or DHCP settings of the
B5800 Branch Gateway system. By default the B5800 Branch Gateway system name is set to match its MAC address. The system name can be changed to something more distinctive. For
more information about the system default settings, see Default configuration
on page 87. Note that if you change the IP address settings, you must restart the system.
Procedure
1. Start Manager and connect to the B5800 Branch Gateway system.
2. In the left navigation pane, click System.
3. On the System tab, in the Name field, enter a distinctive name for this B5800 Branch
Gateway system.
4. Click OK.
5. Click the LAN1 tab.
6. On the LAN Settings sub-tab, do the following: a.
Change the IP Address to match the customer requirements.
b.
Change IP Mask to match the customer requirements.
c.
Change DHCP Mode setting to match the customer requirements.
These settings are used for the LAN port on the back of the control unit.
7. Click OK.
8. Click the LAN2 tab.
9. On the LAN Settings sub-tab, do the following: a.
Change the IP Address to match the customer requirements.
b.
Change IP Mask to match the customer requirements.
c.
Change DHCP Mode setting to match the customer requirements.
These settings are used for the WAN port on the back of the control unit.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 205
Additional system procedures
10. Click OK.
11. Select File > Save Configuration.
12. Reboot the system.
Default passwords
Do not change any other settings than those described below until you have read and understood the B5800 Branch Gateway Security Mode feature. See the IP Office Manager online help for more information. From IP Office Manager, click the Help button in the lowerright section of the window. Then in the left navigation pane, in the Contents tab, select
Security Mode.
Changing the security settings
Procedure
1. Start Manager and connect to the B5800 Branch Gateway system.
2. Select File > Advanced > Security Settings.
3. In the Select IP Office window, click the check box for the appropriate system.
4. Click OK.
5. In the Security Service User Login window, enter a user name and password of an account that has security configuration access to the B5800 Branch Gateway system.
The defaults are security and securitypwd.
6. In the left navigation pane, click System.
7. Click the Unsecured Interfaces tab.
The password in the System Password field is used by Manager for remote software upgrade of the B5800 Branch Gateway system. The default password is
password.
8. Next to the System Password field, click the Change button.
9. Enter a new password and click OK.
10. Click OK.
11. Click on Service Users.
206 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Default passwords
The list shows the service user accounts that can access the system configuration.
The default service users Administrator, Manager and Operator each use the same value (Administrator, Manager and Operator) as their password.
12. For each of these service users: a.
Click on the service user name.
b.
In the Service User Details tab, click on Change and enter a new password.
c.
Click OK.
d.
Click OK.
13. Click on General.
The general security settings are displayed in the main display area.
14. Next to the Password field, click on Change and enter a new password for the security administrator.
15. Click on File > Configuration to exit security configuration mode and return to the
B5800 Branch Gateway configuration.
Changing the remote user password
About this task
The B5800 Branch Gateway configuration contains a user whose password is used as the default for remote dial-in access to the B5800 Branch Gateway network. Use this procedure to change this user's password.
Procedure
1. Start Manager and connect to the B5800 Branch Gateway system.
2. In the left navigation pane, click User.
3. In the user list, click RemoteManager.
4. On the User tab, do the following: a.
In the Password field, enter a new password for the user.
b.
In the Confirm Password field, enter the new password again.
5. Click OK.
6. Select File > Save Configuration.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 207
Additional system procedures
System shutdown
B5800 Branch Gateway systems can be shut down in order to perform maintenance. The shut down can be either indefinite or for a set period of time after which the B5800 Branch Gateway will automatically reboot. During the shut down process, the current configuration in the control unit's RAM memory is copied to the System SD card.
Warning:
• A shutdown must always be used to switch off the system. Simply removing the power cord or switching off the power input may cause errors.
• This is not a polite shutdown, any users calls and services in operation will be stopped.
Once shutdown, the system cannot be used to make or receive any calls until restarted.
• The shutdown process takes up to a minute to complete. When shutdown, the CPU
LED and the base card LEDs 1 and 9 (if trunk daughter card fitted) will flash red rapidly.
The memory card LEDs are extinguished. Do not remove power from the system or remove any of the memory cards until the system is in the this state.
• To restart a system when shutdown indefinitely, or to restart a system before the timed restart, switch power to the system off and on again.
Shutting down the system using Manager
Procedure
1. Start Manager.
2. Select File > Advanced > System Shutdown.
The Select IP Office window appears.
3. Select the B5800 Branch Gateway system you want to shut down.
The System Shutdown Mode window appears.
4. Do one of the following:
• To shut down the system for an indefinite period of time, select Indefinite.
To restart the system you must switch the power off and then on.
• To shut down the system for a specific period of time, select Timed and then specify the duration in hours and minutes.
The system will automatically reboot after the set time has elapsed.
208 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
System shutdown
5. Click OK.
Shutting down the system using the System Status application
Procedure
1. Start System Status and access the system status output.
2. In the navigation panel select System.
3. At the bottom of the screen select Shutdown System.
4. Select the time duration for the shutdown or indefinite.
Shutting down the system using a system phone
About this task
To shut down the system using a system phone, you must be administered as a System Phone user. You can shut down the system using a 1400, 1600, or 9600 series phone (excluding
XX01, XX02, and XX03 models). Unlike Manager, a system phone user cannot select an indefinite shutdown. A system phone user can set a timed shut down of between 5 minutes and 24 hours. Your Login Code is used to restrict access to some system administration functions on the phone.
Procedure
1. Select Features > Phone User > System Admin.
2. Enter your B5800 Branch Gateway user login code.
3. From the menu select System Shutdown.
4. Select a time period for the shutdown. It must be in between 5 minutes and 24 hours.
5. Select Done and then Confirm to begin the shutdown.
Shutting down the system using the AUX button
Procedure
On the control unit, press the AUX button for more than 5 seconds.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 209
Additional system procedures
The control unit will shutdown with the restart timer set to 10 minutes.
Rebooting the system
About this task
You can use Manager to reboot an B5800 Branch Gateway system.
Procedure
1. Start Manager.
2. Select File > Advanced > Reboot.
3. In the Select B5800 window, select the B5800 Branch Gateway system.
4. Enter your user name and password.
5. In the Reboot window, do one of the following:
• Select Immediate to reboot the system immediately.
• Select When Free to reboot the system when there are no calls in progress.
This selection can be combined with the Call Barring options.
• Select Timed and then specify a time in hours and minutes.
This reboots the system the same as When Free but first waits for a specific time. After the specified time, the system waits for there to be no calls in progress and then reboots. This selection can be combined with the Call
Barring options.
Note:
If the time is after midnight, the system's normal daily backup is canceled.
6. In the Call Barring section, select Incoming Calls and/or Outgoing Calls. These settings are used when the reboot mode is When Free. They bar the sending or receiving of any new calls.
7. Click OK.
210 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
About changing components
About changing components
Except for memory cards, cards and external expansions modules must only be removed and
System shutdown on page 208 for more information.
Note that for extension ports, by default both an extension entry and a user entry are configured in the system. Extension entries can be deleted without deleting the corresponding user entry.
This allows retention of the user settings and association of the user with a different extension by changing that extension's Base Extension number to match the user's Extension ID.
In the following procedures, the term component refers to a card fitted into the control unit or an external expansion module.
Replacing a component with one of the same type
About this task
If you are replacing a component with one of the same type and capacity, no configuration changes are required.
Procedure
1. Turn the B5800 Branch Gateway system off. See
2. Remove the card or external expansion module.
Note:
The card slot or expansion port used as the replacement must be installed in the same position.
3. Install the replacement using the appropriate procedure for the type of component.
See Base and trunk card installation
on page 61 or Connecting external expansion modules
on page 72 for more information.
4. Restart the B5800 Branch Gateway system.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 211
Additional system procedures
Replacing a component with one of higher capacity
About this task
If you are replacing a component with one of the same type but with higher capacity, when restarted the B5800 Branch Gateway system will automatically create configuration entries for the new trunks or extensions/users.
Procedure
1. Turn the B5800 Branch Gateway system off. See
2. Remove the card or external expansion module.
Note:
The card slot or expansion port used as the replacement must be installed in the same position.
3. Install the replacement using the appropriate procedure for the type of component.
See Base and trunk card installation
on page 61 or Connecting external expansion modules
on page 72 for more information.
4. Restart the B5800 Branch Gateway system.
5. Use Manager to configure the new trunks or extension/users.
Replacing a component with one of lower capacity
About this task
If you are replacing a component with one of the same type but with lower capacity, when restarted the B5800 Branch Gateway system configuration must be edited to remove redundant entries.
Procedure
1. Turn the B5800 Branch Gateway system off. See
2. Remove the card or external expansion module.
Note:
The card slot or expansion port used as the replacement must be installed in the same position.
3. Install the replacement using the appropriate procedure for the type of component.
See Base and trunk card installation
on page 61 or Connecting external expansion modules
on page 72 for more information.
212 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
About changing components
4. Restart the B5800 Branch Gateway system.
5. Use Manager to delete the trunks or extensions/users in the configuration that are no longer supported by the replacement component.
Replacing a component with one of a different type
About this task
If you are replacing a component with one of a different type, you must perform two procedures; one to permanently remove the component and then one to add the component.
Procedure
1. Remove the existing component. See Permanently removing a component
on page 214.
Note:
Be sure to reboot the system and edit the configuration after you remove the component.
2. Install the new component. See Adding a new component
on page 213.
Adding a new component
About this task
If you are adding a new component to an available slot or port, when restarted the B5800
Branch Gateway system will automatically create configuration entries for the new trunks or extensions/users.
Procedure
1. Turn the B5800 Branch Gateway system off. See
2. Install the new component using the appropriate procedure for the type of
component. See Base and trunk card installation
on page 61 or
Connecting external expansion modules
on page 72 for more information.
3. Restart the B5800 Branch Gateway system.
4. Use Manager to configure the new trunks or extension/users.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 213
Additional system procedures
Permanently removing a component
About this task
If you are permanently removing a component, when restarted the B5800 Branch Gateway system configuration must be edited to remove redundant entries.
Procedure
1. Turn the B5800 Branch Gateway system off. See
2. Remove the card or external expansion module.
3. Restart the B5800 Branch Gateway system.
4. Use Manager to delete the trunks or extensions/users in the configuration that relate to the component removed.
5. In the Control Unit section of the configuration, delete the entry for the component that is no longer present in the system.
Swapping extension users
About this task
This procedure explains how to swap extensions for two users. This example refers to User A and User B which represent any two users for whom you want to swap extensions.
Procedure
1. Load the B5800 Branch Gateway configuration.
2. Select Extension.
3. In the Extension section of the window, select the extension for User A.
4. In the Base Extension field, change the extension to User B's extension.
Note:
If Manager is set to validate edits, a warning appears that says this change conflicts with the existing Base Extension setting of another extension. Ignore the warning at this stage. Click OK.
5. In the Extension section of the window, select the extension for User B.
6. In the Base Extension field, change the extension to User A's extension.
7. Save the configuration back to the B5800 Branch Gateway system.
214 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
About changing extension numbers
8. At each of the extensions, dial the log out short code set on the B5800 Branch
Gateway system. The default is *36.
9. If either user is configured for Forced Login, they will have to complete the login process at their new extension using their Login Code.
About changing extension numbers
The default configuration for a new B5800 Branch Gateway system numbers each extension in sequence, going by module and port order, starting from 201. An extension entry is created in the configuration and also an associated user entry. A similar process occurs when a new extension expansion module is detected.
Important:
Extension versus User: It is important to understand that "extension number" is a user setting that belongs to and moves with the user. For example, a user can login at any phone and that phone then temporarily assumes the user's extension number and settings until they log off. The Base Extension value set for extensions in the B5800 Branch Gateway configuration indicates the default associated user of the extension. It is not the extension number of that port.
Renumbering all extensions and users
About this task
Use this procedure to shift all user extension numbers up or down by a set amount. Any settings linked to those numbers are adjusted including extension Base Extension settings. It does not affect hunt group extension numbers.
Warning:
This procedure alters extension settings and therefore requires a system reboot when the configuration is sent to the B5800 Branch Gateway.
Procedure
1. Select Tools > Extension Renumber.
2. In the Renumber window, in the Value field, enter the amount by which you want to shift the current extension numbering of extensions and users.
3. Click Add or Subtract as appropriate.
4. Click OK.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 215
Additional system procedures
5. Send the configuration back to the B5800 Branch Gateway and select the appropriate settings for the reboot.
Changing a user's extension number
Procedure
1. Select User.
2. Select the relevant user.
3. On the User tab, in the Extension field, change the extension number to the new number.
4. Click on another field.
If an error warning appears it is most likely due to a conflict with an existing use of that extension number. Do one of the following:
• Click Cancel to return the user to their original extension number.
• If you are planning to change the other extension number, click OK and then edit the other entry.
Manager automatically propagates the number change to any hunt groups, incoming call routes, user buttons, bridged appearance buttons and call coverage appearance buttons associated with the user's original extension number.
If the user has an extension with which they are associated by being the extension's Base Extension setting, that setting is not automatically updated.
If the user should still be associated with that extension by default, the extension must be updated manually to match the user's new extension number.
5. To update the user's Base Extension setting, select Extension.
6. On the Extn tab, in the Base Extension field, change the base extension number to match the user extension who should now be associated with that extension port by default.
7. Click OK.
Note:
If a validation error message appears due to a user being associated with two extensions, ignore the message until all the user moves have been completed.
8. Repeat steps 2 through 7 for each user whose extension number you need to change.
216 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Creating a backup of the system configuration using IP Office Manager
9. Click to revalidate the configuration and check that there are no conflicts between users and associated extensions.
10. Send the configuration back to the B5800 Branch Gateway and select appropriate settings for the reboot.
Creating a backup of the system configuration using IP
Office Manager
About this task
Before performing an upgrade, ensure you have a current backup of the B5800 Branch
Gateway system configuration. If you do not, use this procedure to create a backup of the system configuration.
Procedure
1. Start Manager.
2. Select File > Open Configuration.
3. In the Select B5800 Branch Gateway window, select the appropriate system.
4. Click OK.
5. Enter the name and password for a service user account on that system.
6. Click OK.
A BOOTP entry for the system is created in Manager. This also confirms communication between the Manager PC and the B5800 Branch Gateway system.
7. Select File > Save Configuration As... and save a copy of the configuration file onto the PC.
Creating a backup of the system configuration using
System Manager
About this task
When you perform a backup of the system configuration from System Manager, the backup is stored on the local B5800 Branch Gateway. To store the system configuration backup on the
System Manager server, you must synchronize the B5800 Branch Gateway with System
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 217
Additional system procedures
Manager. See Synchronizing B5800 Branch Gateway with System Manager
on page 164 for more information.
Procedure
1. From the System Manager console, under Elements, select B5800 Branch
Gateway.
2. In the left navigation pane, click Backup and Restore.
3. On the B5800 Branch Gateway Backup and Restore page, select the B5800 Branch
Gateway device for which you want to create a backup.
4. Click Backup.
5. Do one of the following:
• Click Now to run the backup job now.
• Click Schedule to run the backup job at a scheduled date and time.
Upgrades using IP Office Manager
IP Office Manager includes software files for control units, external expansion modules and phones appropriate to the system's software level. The B5800 Branch Gateway system can be upgraded in two ways using IP Office Manager that is connected directly to the B5800
Branch Gateway system. These methods are:
• Using the IP Office Manager upgrade wizard. See
on page 219.
• Using the System SD card. See System upgrade using the System SD card on
page 258.
B5800 Branch Gateway systems can also be upgraded using Avaya Aura ® System Manager.
This method is used for systems that have already been upgraded from R6.1 to R6.2 and is used when multiple branches require upgrades. For more information, see
system with an R6.2 service pack on page 95.
Note:
Check the latest B5800 Branch Gateway Technical Bulletin for the B5800 Branch Gateway software release before proceeding any further. It may contain information relating to changes that occurred after this document was completed. Bulletins are available from http:// support.avaya.com
• Multiple Managers — If more than one copy of Manager is running it is possible for the
B5800 Branch Gateway system to request BIN files from a different Manager from the
218 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Upgrades using IP Office Manager one that started the upgrade process. Ensure that only one copy of Manager is running when upgrading an B5800 Branch Gateway system.
• Other B5800 Branch Gateway applications — Upgrading the core software of the
B5800 Branch Gateway control unit may require upgrades to associated software.
Typically B5800 Branch Gateway is compatible with the previous release of most B5800
Branch Gateway applications. However, for each B5800 Branch Gateway core software release, there may be exceptions. See the Technical Bulletin for the B5800 Branch
Gateway core software release for more information.
Using the upgrade wizard
About this task
Before using the upgrade wizard, be sure you have a current backup of the system
configuration. See Creating a backup of the system configuration using IP Office Manager
on page 217 for more information.
Procedure
1. Start Manager.
2. Select File > Advanced > Upgrade.
3. Click the check box for the appropriate system.
4. Click Upgrade.
The UpgradeWiz scans for B5800 Branch Gateway modules using the address specified in the Unit/Broadcast Address field.
5. If the expected control units are not shown, adjust the address in the Unit/
Broadcast Address field, and click Refresh.
The current version of each B5800 Branch Gateway .bin file held in the control units memory is displayed. This is regardless of whether that .bin file is currently being used by any module in the system.
In the Available column, Manager lists the versions of software it has available. If
Manager detects that there is a higher version available, the check box for that row is automatically selected.
6. Click the check box for the modules you want to upgrade.
7. Click the check box for Validate.
When this option is selected, the upgrade wizard checks the amount of free RAM memory available in the control unit to temporarily store the new bin files. If insufficient memory is available, you will be prompted whether to continue with an off-line upgrade or cancel upgrading. If offline is selected, the system is rebooted into offline mode. It may be necessary to use the Refresh option within the upgrade wizard to reconnect following the reboot. Validate upgrade can then be attempted again to check the amount of available RAM memory for transfer of bin files. If the
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 219
Additional system procedures memory is still insufficient, the option is offered to either do an unvalidated upgrade or cancel.
During a validated upgrade, the bin files required are transferred to the system and stored in temporary memory. The backup system files and upload system files actions are performed. Once all file transfers are completed, the upgrade wizard promps whether it is okay to proceed with the upgrade process. Select Yes to continue. Each module being upgraded will delete its existing core software, restart and load the new software file that was transferred. This process may take several minutes for each unit.
8. Select the following options as appropriate:
• Click the check box for Backup System Files if, before upgrading to the new software, you want the current files in the System SD cards /primary folder copied to a /backup folder.
• Click the check box for Upload System Files if you want the full set of software files that Manager has to be copied to the /primary folder on the System SD card. In addition to control unit and module software this will include phone software files. Following the reboot, the phone will upgrade using those files if necessary.
• Click the check box for Restart IP Phones if you want all Avaya IP phones to be restarted following the upgrade and reboot. This will cause them to recheck whether the firmware they currently have loaded matches that on their configured file server. Use this option if the B5800 Branch Gateway system is the file server and the upgrade included new IP phone firmware.
9. Click Upgrade.
The system password for each system is requested.
10. Enter the system password and click OK.
Restoring the system configuration using System
Manager
Procedure
1. From the System Manager console, under Elements, select B5800 Branch
Gateway.
2. In the left navigation pane, click Backup and Restore.
3. On the B5800 Branch Gateway Backup and Restore page, select the B5800 Branch
Gateway device whose backup configuration you want to restore. You can select multiple devices.
220 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
External output port (EXT O/P)
4. Click Restore.
5. On the B5800 Branch Gateway Restore page, do one of the following:
• Click System Configuration to restore the respective system configurations available in System Manager to the B5800 Branch Gateway device. The configuration you restore is the latest configuration available in System
Manager.
• Click User to restore the respective users from System Manager to the B5800
Branch Gateway device.
• Click System Configuration and Users to restore the respective system configurations and users from System Manager to the B5800 Branch Gateway device.
• Click Restore Backup Stored on Devices to restore the locally backed up configuration to the B5800 Branch Gateway device.
6. Do one of the following:
• Click Now to perform the restore activity now.
• Click Schedule to perform the restore activity at a scheduled date and time.
External output port (EXT O/P)
The B5800 Branch Gateway control unit is equipped with an external output port. The port is marked as EXT O/P and is located on the back of the control unit adjacent to the power supply input socket.
The port can be used to control up to two external devices such as door entry relay switches.
The usual application for these switches is to activate relays on door entry systems. However, as long as the criteria for maximum current, voltage and if necessary protection are met, the switches can be used for other applications.
The switches can be switched closed, open or pulsed (closed for 5 seconds and then open).
This can be done in a number of ways:
• Using B5800 Branch Gateway short codes.
• Through the Door Release option in B5800 Branch Gateway SoftConsole.
Default short codes: The following are the default short codes in the B5800 Branch Gateway configuration for external output switch operation. They use the short code features Relay On
(closed), Relay Off (open) and Relay Pulse.
State Switch 1 Switch 2
Closed *39 *42
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 221
Additional system procedures
State
Open
Pulse
*40
*41
Switch 1
*43
*44
Switch 2
EXT O/P connections
EXT O/P ports use a standard 3.5mm stereo jack plug for connection. The B5800 Branch
Gateway is able to open (high resistance), close (low resistance) or pulse (close for 5 seconds and then open) two switches within the port. Either switch can be operated separately. These switches are intended for activation of external relays in systems such as door opening systems.
Caution:
In installations where this port is connected to a device external to the building, connection must be via a towerMAX SCL/8 Surge Protector and a protective ground connection must be provided on the B5800 Branch Gateway control unit.
EXT O/P Pin
1
2
3
Description
Switch 1
Switch 2
0 Volts (Ground/Chassis)
• Switching Capacity: 0.7A
• Maximum Voltage: 55V d.c
• On state resistance: 0.7 ohms
• Short circuit current: 1A
• Reverse circuit current capacity: 1.4A
• Ensure that pins 1 and 2 are always at a positive voltage with respect to pin 3
3.5mm stereo audio jack plugs are frequently sold as pre-wired sealed modules. It may be necessary to use a multi-meter to determine the wiring connections from an available plug.
Typically 3 (common to both relays) is the cable screen.
222 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Example of BRI So8 module configuration
Example of BRI So8 module configuration
The ports on a BRI So8 module can be used for the connection of ISDN devices. Following are examples of how to configure a port on the BRI So8 module for an ISDN terminal and for video conferencing.
Example 1: ISDN terminal
About this task
In this example, calls on DID 123456 are routed to the first port of the So8 expansion module.
That port has been configured as Line Group ID 701.
Procedure
1. Configure an incoming call routing. The destination is a short code that directs the call to the line group ID that contains the SO lines.
The Bearer Capability has been set to Any to allow data and voice via this route.
• Line Group ID: 0
• Incoming Number: 123456
• Destination: 123456
• Bearer Capability: Any
2. Create a system short code. This is the destination used in the incoming call route.
• Short Code: 123456
• Telephone Number: 123456
• Line Group ID: 701
• Feature: Dial
3. Send the configuration to the control unit.
Any call coming into the main system on DID 123456 will now be passed directly to the first port.
4. If you wish to assign DIDs from your main pool to individual ports and avoid network charges when dialing between them, try variations on the following: a.
You have DID ranges, for example: 7325551000 to 7325551099. You wish to assign 7325551000-19 to port 1 and 7325551020-20 to port 2 etc.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 223
Additional system procedures b.
Configure incoming call route. The # is used here instead of "n" to avoid problems with "Main". The minus sign means the number is processed from the left and so will wait for the whole number.
• Line Group ID: 701
• Incoming Number: -100x
• Destination: # c.
Repeat for Line Group ID 702 etc.
d.
Create short codes, for example:
• Short Code: 100x
• Telephone Number:
• Line Group ID: 701
• Feature: Dial
S0 calls dialed without the area code are handled locally without network charges.
Calls with area calls will go via the network.
Example 2: video conference
About this task
In this example, calls are routed to a Polycom Viewstation module connected to a S0 port of the B5800 Branch Gateway system.
The following settings were used on 4 incoming data channels of a PRI line:
• Line Number: 5
• Channel Allocation: 23 -> 1
• Switch Type: 5ESS
• Line Sub Type: PRI
• Provider: AT&T
• Channels: 1-4
• Incoming Line Group: 95
• Outgoing Line Group: 95
• Direction: Bothway
• Bearer: Data
• Service: Accunet (this is a important)
• Admin: In Service
224 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Example of BRI So8 module configuration
To route an incoming video call on the PRI lines configured above to an So8 module requires the following:
Procedure
1. Create a dial short code that has the SO port as its destination line group. For this example the following is used:
• Short Code: 1500
• Number:
• Feature: Dial
• Line Group: 601 (the So8 port number)
2. Create an incoming call routing that routes the appropriate calls to that short code.
For this example the following is used:
• Line Group: 95 (identifies calls using the PRI lines configured above)
• Destination: 1500 (the short code created above)
• Bearer: Any
3. To allow the video device on the S0 port to make outgoing calls to the PRI lines also requires a short code. For this example the following is used:
• Code: 91N;
• Number: N
• Feature: Dial
• Line Group: 95
Polycom Video module settings
The Polycom modules used in the previous example were the Viewstation 128,
Viewstation 256 and Viewstation MP.
The Polycom module must have software that supports 'Standard ETSI ISDN'
(European ISDN) and have its ISDN Switch Protocol setting set to 'Standard ETSI
Euro-ISDN'
The following were the settings used during testing:
Characteristics
• Polycom View Station 512 MP
• NTSC UIS Interface
• View Station PVS 1419
Admin/General Setup
Admin/Software and Hardware/
Software
• Software: 7.0.1
• Network Interface: S/T Interface
• ISDN Version: IEUS v18:a00320
Admin/Video Network/ISDN Video
Network
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 225
Additional system procedures
Characteristics
• Country: USA
• Language: English (USA)
• Auto Answer: Yes
• AllowDial: Yes
• Allow User Setup: Yes
• Maximum Time on Call: 480
User Setup
• Auto Answer: Yes
• PIP: Auto
• Far Control of Near Camera: Yes
• MP Mode: Auto
System Information
• Release: 7.0.1
• Model: VS: 512
Admin/Video Network
• MultiPoint Setup: Auto
Admin/Software and Hardware/
Software
• Country Code: 1
• Area Code: 732
• Number A: blank
• Number B: blank
• ISDN Switch Protocol: Standard
ETSI Euro-ISDN
Admin/Video Network/IMUX
• Numbers: blank
• SPID: blank
• Audio Quality: 168KB/s
• Advanced Dialing: Dial Channels in
Parallel
Admin/Software and Hardware/
Hardware
• Camera: NTSC
• Video Comm Interface:
ISDN_Quad_BRI
• Network Interface Type: S/T Interface
Admin/Video Network/Call
Preference
• ISDN Video Calls (H:320): Yes
SNMP
SNMP (Simple Network Management Protocol) is a standard network protocol that allows the monitoring and management of data devices across a network. An SNMP agent can be built into network devices such as routers and hubs. An SNMP manager application, for example
CastleRock or HP OpenView, can then communicate with those devices.
B5800 Branch Gateway supports SNMP communication. This communication can be:
• Polling: Some SNMP applications (called "managers") send out polling messages to the network. They then record the responses of any SNMP enabled devices (called "agents").
226 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
SNMP
This allows the application to create a network map and to raise an alarm when devices previously present do not respond.
- Most SNMP manager applications can also do simple IP address polling to locate non-SNMP enabled devices. However this method of polling does not identify the device type or other information.
- SNMP polling including details about the responding device. For example an B5800
Branch Gateway control unit's response includes the control unit type, level of software, routing table information, up time, etc.
• Traps: When certain events occur, a devices SNMP agent can send details of the event to the SNMP manager. This is called an SNMP trap. These appear in the event log of the
SNMP manager. Most SNMP managers can be configured to give additional alerts in response to particular traps.
• Management: Some SNMP agents support device management and configuration changes through the SNMP manager interface. This is not supported by B5800 Branch
Gateway.
B5800 Branch Gateway SNMP operation has been tested against Castle Rock SNMPc-EE
5.1.6c and HP OpenView Network Node Manager 6.41.
What information is available via SNMP
As described above, SNMP information can either be polled by the SNMP application or received as the result of the B5800 Branch Gateway sending SNMP trap information.
While the MIB files should not be edited, they can be read using a text editor and contain descriptions of all the various information objects that can be polled or sent and the information
that each object will include. For a list of the MIB files, see Installing the B5800 Branch Gateway
on page 227. The NOTIFICATION-TYPE objects are those used for SNMP traps.
The other types of objects are those that can be polled.
Installing the B5800 Branch Gateway MIB files
To allow full communication between an SNMP agent and an SNMP manager, the SNMP manager must load MIB files (Management Information Base) specific to the SNMP agent device and the features it supports. These MIB files contain details of the information the agent can provide and the traps that it can send.
The MIB files for B5800 Branch Gateway operation are included on the B5800 Branch Gateway
DVD in the folder \AdminCD\smnp_mibs. The actual files required and the method of loading depend on the SNMP manager application being used. The details below cover the two SNMP manager applications supported.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 227
Additional system procedures
HP OpenView Network Node Manager
Procedure
1. Copy the following MIB files to the application's MIB folder.
MIB File rfc2737-entity-mib.mib
avayagen-mib.mib
ipo-prod-mib.mib
ipo-mib.mib
ipo-phones-mib.mib
Source snmp_mibs\standard folder on
OpenView Install CD.
\AdminCD\snmp_mibs\IPOffice folder on B5800 Branch Gateway Admin
DVD.
\AdminCD\snmp_mibs\IPOffice folder on B5800 Branch Gateway Admin
DVD.
\AdminCD\snmp_mibs\IPOffice folder on B5800 Branch Gateway Admin
DVD.
inet-address-mib.mib
\AdminCD\snmp_mibs\Standard folder on B5800 Branch Gateway Admin
DVD.
rfc2213-integrated-services-mib.mib
\AdminCD\snmp_mibs\standard folder on OpenView Install CD.
diffserv-dscp-tc.mib
\AdminCD\snmp_mibs\Standard folder on B5800 Branch Gateway Admin
DVD.
diffserv-mib-hpov.mib
\AdminCD\snmp_mibs\Standard folder on B5800 Branch Gateway Admin
DVD.
\AdminCD\snmp_mibs\IPOffice folder on B5800 Branch Gateway Admin
DVD.
2. Start the OpenView Network Node Manager console.
3. Select Options and then Load/Unload MIBs: SNMP.
4. Select Load and select all the MIB files listed above.
5. Select Compile.
228 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
SNMP
Castlerock SNMPc 5.1.6c and earlier
Procedure
1. Copy the following MIB files to the application's MIB folder. This folder is typically
C:\Program Files\SNMPc Network Manager\mibfiles.
ENTITY-MIB
MIB file
AVAYAGEN-MIB.mib
IPO-PROD-MIB.mib
IPO-MIB.mib
INET-ADDRESS-MIB.mib
INTEGRATED-SERVICES-MIB
DIFFSERV-DSCP-TC.mib
DIFFSERV-MIB.mib
IPO-PHONES-MIB.mib
Source
\AdminCD\snmp_mibs\Standard on
B5800 Branch Gateway Admin DVD.
\AdminCD\snmp_mibs\IPOffice on
B5800 Branch Gateway Admin DVD.
\AdminCD\snmp_mibs\IPOffice on
B5800 Branch Gateway Admin DVD.
\AdminCD\snmp_mibs\IPOffice on
B5800 Branch Gateway Admin DVD.
\AdminCD\snmp_mibs\Standard on
B5800 Branch Gateway Admin DVD.
\AdminCD\snmp_mibs\Standard on
B5800 Branch Gateway Admin DVD.
\AdminCD\snmp_mibs\Standard on
B5800 Branch Gateway Admin DVD.
\AdminCD\snmp_mibs\Standard on
B5800 Branch Gateway Admin DVD.
\AdminCD\snmp_mibs\IPOffice on
B5800 Branch Gateway Admin DVD.
2. In SMNPc select Config > MIB Database.
3. Select Add and select the MIB files listed above in the order listed.
Castlerock SNMPc V5.0.1
Procedure
1. Copy all of the B5800 Branch Gateway MIBs and standard MIBs from the B5800
Branch Gateway Administrator Applications DVD to the SNMPc mibfiles directory.
2. In the SNMPc mibfiles directory open the files STANDARD.mib and SNMPv2-
SMI.mib in Notepad.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 229
Additional system procedures
3. In the SNMPv2-SMI.mib file find the definition of zeroDotZero and copy this to the clipboard.
4. In the STANDARD.MIB file find the SNMPv2-SMI section and paste in the definition of zeroDotZero from the clipboard before the end of this section (just before the
END statement).
5. Save the modified STANDARD.MIB file.
6. Add the MIB file SNMP-FRAMEWORK-MIB.mib to the MIB database.
7. Add all the MIB files in the order listed.
8. Compile the MIBs ready for use.
Note:
The IPO-PHONES-MIB.mib relies upon the DIFFSERV-MIB.mib for the definition of the textual convention of IndexInteger. The DIFFSERV-MIB needs the definition of the textual convention zeroDotZero which is normally defined in
SNMPv2-SMI.mib. However including SNMPv2-SMI.mib in the MIB file compilation list results in errors due to conflicts with what appear to be internal definitions within SNMPc and the SNMPv2-SMI section in its STANDARD.mib
file. Therefore to resolve the issue the required definition of zeroDotZero must be placed in the SNMPv2-SMI section in SNMPc's STANDARD.mib file.
Enabling SNMP and polling support
About this task
In order for the B5800 Branch Gateway control unit to be discovered and polled by an SNMP manager, its SNMP agent must be enabled and placed in the same read community as the
SNMP manager.
Procedure
1. Start Manager and connect to the B5800 Branch Gateway system.
2. In the left navigation pane, click System.
3. Click the System Events tab.
4. Select SNMP Enabled.
5. In the SNMP Port field, enter the UDP port number used by the SNMP agent to listen for and respond to SNMP traffic.
The default is 161.
6. In the Community (Read-only) field, enter the community to which the device belongs for read access.
This community name must match that used by the SNMP manager application when sending requests to the device. The community public is frequently used to
230 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
SNMP establish communication and then changed (at both the SNMP agent and manager ends) for security.
7. Click OK.
8. Select File > Save Configuration to send the configuration back to the B5800
Branch Gateway and then select reboot.
After the reboot, the SNMP manager will be able to discover the control unit. The discovery includes the control unit type and the current level of core software.
Enabling SNMP trap sending
About this task
Use this procedure to configure the SAL Gateway as a trap destination. A maximum of 5 SNMP management stations can be configured as B5800 trap destinations. System Manager must be configured as a trap destination. When the Initial Installation Utility is used, System Manager is automatically configured as a trap destination. See
Using the Initial Installation Utility on
page 121 for more information.
Procedure
1. Start Manager and connect to the B5800 Branch Gateway system.
2. In the left navigation pane, click System.
3. Click the System Events tab.
4. In the Configuration sub-tab, in the SNMP Agent section, ensure the SNMP
Enabled check box is selected.
5. In the Community (read-only) field, enter the SNMP community name to which the system belongs.
This community name must match that used by the SNMP manager application when sending requests to the device. The community public is frequently used to establish communication and then changed (at both the SNMP agent and manager ends) for security.
6. In the SNMP Port field, accept the default.
7. In the Device ID field, enter the alarm ID or PID of the registered system.
Note:
This enables product alarming back to Avaya via the Secure Access Link (SAL).
The unique alarm ID is included in the var-bind of all SNMP trap notifications sent by the system. The alarm ID, or PID, is parsed out of the alarm and used for automatic case creation by matching the registered system's customer record with the alarm event.
8. In the Contact field, enter contact information as appropriate.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 231
Additional system procedures
9. In the Location field, enter location information as appropriate.
10. Click the Alarm tab.
11. Click Add.
12. In the New Alarm section, do the following: a.
Click the Trap option button.
b.
In the IP Address field, enter the IP address of the PC running the SNMP manager application.
c.
In the Port field, enter the port on which the trap messages should be sent.
This is the UDP port on which the B5800 Branch Gateway sends SNMP trap messages. The default is 162.
d.
In the Community field, enter the community that will be used by the agent and the SNMP manager.
13. In the Events section, click the check boxes for the events you want to send.
See the Manager on-line help for a description of the events.
14. Click OK.
15. Select File > Save Configuration to send the configuration back to the B5800
Branch Gateway and then select reboot.
DTE port maintenance
The DTE port on the back of control unit is not normally used when configuring an B5800
Branch Gateway system. However, in extreme cases, the DTE port can be used to default the system's configuration or to erase the core software if necessary.
Warning:
The procedures in this section should only be performed if absolutely necessary to return a system back to working order. In all cases, you must have a backup copy of the system configuration before you perform these procedures. See
Creating a backup of the system configuration using IP Office Manager on page 217.
The DTE ports on B5800 Branch Gateway expansion modules are not used for any maintenance or diagnostics.
RS232 DTE port settings
The RS232 DTE ports are located on the rear of all control units and external expansion modules. The DTE ports on external expansion modules are not used. The RS232 DTE ports
232 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
DTE port maintenance on the control units can be used for system maintenance and connection of serial terminal adaptors.
An asynchronous terminal program such as HyperTerminal is also required. Configure this for operation via a PC serial port, as follows:
Bits per second 38,400 Parity
Data bits 8 Stop Bits
None Flow Control
1
None
Settings > Emulation TTY
DTE cables
These cables are used for system maintenance and diagnostics under Avaya guidance. They can also be used for connection of RS232 serial terminal adaptor equipment to the control unit.
This cable is a "Straight through DB9 female to DB9 male serial cable."
4
9
5
1
2
7
8
6
9-Way RS232 DTE Port
3 Receive data
Signal
Transmit Data
RTS (Request To Send)
CTS (Clear To Send)
DSR (Data Set Ready)
Ground
DCD (Data Carrier Detect)
DTR (Data Terminal Ready)
RI (Ring Indicator)
4
9
5
1
2
7
8
6
3
PC/Terminal Adaptor
About erasing the configuration
The following procedures erase the B5800 Branch Gateway configuration stored in the control unit. This includes both the current configuration being used in RAM memory and the backup configuration stored in non-volatile memory. Following this, the B5800 Branch Gateway will restart with a default configuration.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 233
Additional system procedures
These procedures should be performed from a PC with a fixed IP address, directly connected to the B5800 Branch Gateway control unit and with the B5800 Branch Gateway system disconnected from any network. The control unit IP address will default to 192.168.42.1.
Important:
Do not perform any of these processes unless absolutely necessary. The configuration settings can be returned to the default settings using Manager by selecting File > Advanced
> Erase Configuration command.
Erasing the configuration via debug
About this task
This procedure erases the system's configuration settings but does not alter the security settings. It is easier to use than the boot loader method. Before you perform this procedure,
Procedure
1. Attach the serial cable between the PC and the DTE port on the control unit.
2. Start the terminal program on your PC.
Note:
Ensure that the DTE port settings are configured as described in
on page 232. Within a HyperTerminal session, the current settings are summarized across the base of the screen.
3. Enter AT (upper case).
An OK response appears.
4. Enter AT-DEBUG.
The time and date and then the Hello> prompt appears to show the system is ready to accept commands.
5. To erase the current configuration in RAM memory, enter eraseconfig.
The Hello> prompt reappears.
6. To erase the backup configuration stored in non-volatile Flash memory enter
erasenvconfig.
The Hello> prompt reappears.
7. To reboot the system, enter reboot.
The system reboots and restarts with a defaulted configuration.
8. Close the terminal program session.
234 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
DTE port maintenance
9. Use Manager to edit and then upload an old configuration file or receive and edit the system's now defaulted configuration.
Erasing the configuration and security settings via the boot loader
About this task
This procedure erases the system's configuration settings and the security settings and resets them to the default settings. Before you perform this procedure, be sure you have a current backup of the system configuration. See
Creating a backup of the system configuration using
IP Office Manager on page 217 for more information.
Procedure
1. Attach the serial cable between the PC and the DTE port on the control unit.
2. Start the terminal program on your PC.
Note:
Ensure that the DTE port settings are configured as described in
on page 232. Within a HyperTerminal session, the current settings are summarized across the base of the screen.
3. Arrange the program windows so that the terminal program and Manager TFTP log are visible at the same time.
4. Switch off power to the control unit.
5. Power on the control unit and press the escape key every second until you get a loader message. An example of this message is:
P12 Loader 2.4
CPU Revision 0x0900
6. Enter AT (upper case).
An OK response appears. If OK does not appear, check the settings of your terminal program.
7. To erase the alarm log, enter AT-X1.
8. To erase the backup configuration stored in non-volatile memory, enter AT-X2.
An OK response appears.
9. To erase the current configuration in RAM memory, enter AT-X3
A series of OK responses appear.
10. Switch power to the control unit off and then back on.
Messages appear as the control unit performs the start-up tasks.
11. Close the terminal program session.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 235
Additional system procedures
12. Use Manager to edit and then upload an old configuration file or receive and edit the system's now defaulted configuration.
Resetting the security settings to the default settings
About this task
This procedure resets the systems security settings back to the default settings but does not alter the configuration settings.
Procedure
1. Attach the serial cable between the PC and the DTE port on the control unit.
2. Start the terminal program on your PC.
Note:
Ensure that the DTE port settings are configured as described in
on page 232. Within a HyperTerminal session, the current settings are summarized across the base of the screen.
3. Enter AT (upper case).
An OK response appears. If OK does not appear, check the settings of your terminal program.
4. Enter AT-SECURITYRESETALL.
You are prompted to confirm the control unit's MAC address.
5. Enter the MAC address.
An OK response appears.
6. Close the terminal program session.
7. Use Manager to edit the system's now defaulted security settings.
Resetting the configuration and security settings to the default settings via the boot loader
About this task
This procedure erases the system's configuration settings and the security settings and resets them to the default settings. Before you perform this procedure, be sure you have a current backup of the system configuration. See
Creating a backup of the system configuration using
IP Office Manager on page 217 for more information.
236 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
DTE port maintenance
Procedure
1. Attach the serial cable between the PC and the DTE port on the control unit.
2. Start the terminal program on your PC.
Note:
Ensure that the DTE port settings are configured as described in
on page 232. Within a HyperTerminal session, the current settings are summarized across the base of the screen.
3. Arrange the program windows so that the terminal program and Manager TFTP log are visible at the same time.
4. Switch off power to the control unit.
5. Power on the control unit and press the escape key every second until you get a loader message. An example of this message is:
P12 Loader 2.4
CPU Revision 0x0900
6. Enter AT (upper case).
An OK response appears. If OK does not appear, check the settings of your terminal program.
7. To erase the backup configuration stored in non-volatile memory, enter AT-X2.
An OK response appears.
8. To erase the current configuration in RAM memory, enter AT-X3
A series of OK responses appear.
9. Switch power to the control unit off and then back on.
Messages appear as the control unit performs the start-up tasks.
10. Close the terminal program session.
11. Use Manager to edit and then upload an old configuration file or receive and edit the system's now defaulted configuration.
About erasing the operational firmware
When the firmware loaded by the control unit is erased, the control unit begins making BOOTP requests for a replacement firmware file. Manager can act as a BOOTP server and respond to the control units request with the appropriate file from those installed with Manager.
When the firmware loaded by the B5800 Branch Gateway control unit is erased, the control unit will first look for replacement firmware on the System SD card before falling back to using a BOOTP request to Manager.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 237
Additional system procedures
The procedure should be performed from a PC with a fixed IP address, directly connected to the B5800 Branch Gateway control unit and with the B5800 Branch Gateway system disconnected from any network. During the process, the control unit's IP address may default to a value in the 192.168.42.1 to 192.168.42.10 range. If this occurs it may be necessary to amend the BOOTP entry in Manager to match the address the system is using.
Important:
• Do not erase the core software unless absolutely necessary. The B5800 Branch
Gateway software can normally be upgraded using Manager.
• These procedures erase the operational software. Before performing these procedures, you must know the MAC and IP addresses of the system, plus have a system backup and the correct .bin file for the control unit type and level of software.
• The presence of any firewall blocking TFTP and or BOOTP will cause these procedures to fail.
Erasing the core software via debug
Procedure
1. Start Manager.
2. In the BOOTP entries, check that there is an entry that matches the MAC address,
IP address and .bin file used by the system. An entry is normally automatically created when a configuration has been loaded from the B5800 Branch Gateway system.
3. If an entry is not present, do the following: a.
Create a new entry manually. The MAC address and IP address can be found in the control unit settings in the configuration file.
b.
Close Manager.
c.
Restart Manager.
4. Under File > Preferences ensure that Manager is set to 255.255.255.255. Also check that Enable BootP Server is checked.
5. Select View > TFTPLog.
6. Check that the required .bin file is present in Manager's working directory.
7. Attach the serial cable between the PC and the DTE port on the control unit.
8. Start the terminal program on your PC.
Note:
238 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
DTE port maintenance
Ensure that the DTE port settings are configured as described in
on page 232. Within a HyperTerminal session, the current settings are summarized across the base of the screen.
9. Enter AT (upper case).
An OK response appears.
10. Enter AT-DEBUG.
The time and date and then the Hello> prompt appears to show the system is ready to accept commands.
11. To erase the current configuration in RAM memory enter upgrade.
The B5800 Branch Gateway system erases the current software and then sends out a BOOTP request on the network for new software. Manager responds and starts transferring the software using TFTP.
Erasing the core software via the boot loader
Procedure
1. Start Manager.
2. In the BOOTP entries, check that there is an entry that matches the MAC address,
IP address and .bin file used by the system. An entry is normally automatically created when a configuration has been loaded from the B5800 Branch Gateway system.
3. If an entry is not present, do the following: a.
Create a new entry manually. The MAC address and IP address can be found in the control unit settings in the configuration file.
b.
Close Manager.
c.
Restart Manager.
4. Under File > Preferences ensure that Manager is set to 255.255.255.255. Also check that Enable BootP Server is checked.
5. Select View > TFTPLog.
6. Check that the required .bin file is present in Manager's working directory.
7. Attach the serial cable between the PC and the DTE port on the control unit.
8. Start the terminal program on your PC.
Note:
Ensure that the DTE port settings are configured as described in
on page 232. Within a HyperTerminal session, the current settings are summarized across the base of the screen.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 239
Additional system procedures
9. Arrange the program windows so that the terminal program and Manager TFTP log are visible at the same time.
10. Switch off power to the control unit.
11. Power on the control unit and press the escape key every second until you get a loader message. An example of this message is:
P12 Loader 2.4
CPU Revision 0x0900
12. Enter AT (upper case).
An OK response appears. If OK does not appear, check the settings of your terminal program.
13. Enter AT-X.
Multi-Sector Erase response appears. The control unit then requests the .bin file that is stored on the System SD card.
14. If the files do not appear to be transferring, check that the IP address shown in the
TFTP log matches the BOOTP entry. Adjust the BOOTP entry if necessary.
When the file transfers are completed, the system reboots.
Reset button
The Reset button is on the control unit. Pressing the button while the control unit is starting up will pause the start up until the button is released. The effect of pressing the button during normal operation will depend on how long the button is pressed and is indicated by the CPU
LED.
Press Duration
(seconds)
0 to 5
5 to 10
10 to 30
30 to 40
CPU LED Action Summary
Off
Orange
Flashing orange Erase configuration/ immediate reboot
Red
None None
Reboot when free Reboot when free with new incoming/outgoing call barring.
A reboot using the reset button is recorded in the audit trail.
Erase all
Erase the configuration, alarm log and audit trail. Immediate reboot without waiting for
active calls to end. See About erasing the configuration
on page 233 for more information.
Erase configuration, alarm log
240 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Press Duration
(seconds)
Over 40
CPU LED
Flashing green None
Action
DTE port maintenance
Summary
erasing the operational firmware
on page 237 for more information.
None
Creating a WAN link
About this task
This procedure is a high level procedure for creating a data link from Site A to Site B via the
WAN ports. For this example the IP address is 192.168.43.1.
Procedure
1. At Site A, on IP address 192.168.43, create a normal service.
The service name can be any text and is used to identify this particular service. The account name and password entered for the service are presented to the remote end, therefore must match the user name and password configured at Site B. The
Encrypted Password option can only be used if the remote end also supports
CHAP.
2. Create a user.
Under the Dial In tab, select Dial In On. This User account is used to authenticate the connection from the Site B. Note that if the service and user have the same name these two configuration forms are automatically linked and become an
Intranet service. The user password is displayed at the bottom of the Service tab as the Incoming Password.
3. Setup RAS.
If CHAP is to be used on this link, then the Encrypted Password option must be checked in the service and in the RAS service. The name of the RAS service must match the name of the service at Site B. Note that if the RAS settings are given the same name as the service and user they are automatically linked and become a
WAN service. Ensure that the Encrypted Password option is not checked when using a WAN service.
4. Edit the WAN port.
Do not create a new WAN port. The WAN port is automatically detected. If a WAN port is not displayed, connect the WAN cable, reboot the control unit and receive the configuration. The WAN port configuration form should now be added.
5. Create an IP Route.
In the IP address field enter the network address of the remote end — not the IP address of the control unit. Under Destination select the service created above.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 241
Additional system procedures
6. At Site B, on IP address 192.168.43, repeat steps 1 through 5 but alter the details to create a route from Site B to Site A.
242 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Chapter 17: SD card management
There are two SD card slots in the control unit. They are labeled System SD and Optional SD.
Note:
For B5800 Branch Gateway, the System SD card must be a B5800 Branch Gateway System SD card.
You cannot use an IP Office SD card in the System SD card slot on a B5800 Branch Gateway device.
For more information, see “B5800 Branch Gateway System SD card” under
on page 20.
System SD card slot
• An Avaya System SD card must be present in this slot at all times. This card holds copies of the
B5800 Branch Gateway firmware and configuration and is used as the control units non-volatile memory.
• Each System SD card has a unique Feature Key serial number which is used for generating and validating licenses entered into the B5800 Branch Gateway configuration.
• The card stores the prompts for Embedded Voicemail operation and acts as the message store for embedded voicemail messages.
• Prior to any planned shutdown or restart of the B5800 Branch Gateway system, the current configuration running in the system's RAM memory is copied to the primary folder on the System SD card and to the systems non-volatile memory.
• Following a restart, the software in the primary folder is loaded by the control unit. If the required software is not present or valid, a sequence of fallback options is used, see
Cards on page 246 for more information.
• Following a restart, the configuration file, if present, in the primary folder is loaded by the control unit.
If no file is present the system will check for a file in its internal non-volatile memory. If no copy is found it will generate a default configuration file. See
Booting from the SD Cards on page 246 for
more information.
• Once each day (approximately between 00:00 and 00:30) the B5800 Branch Gateway will copy the current configuration running in its RAM memory to the primary folder on the card.
• Configuration changes made using Manager are first written to the copy of the configuration file on the card and then merged with the configuration running in the system's RAM memory.
• The write lock setting on cards in the System SD card slot is ignored.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 243
SD card management
Optional SD card slot
• A card does not have to be present in this slot for normal B5800 Branch Gateway operation. The slot can be used for various maintenance actions.
• A card with updated B5800 Branch Gateway software or configuration can be inserted into the
Optional SD card slot and those files are then transferred to the System SD card in order to upgrade the B5800 Branch Gateway system.
• The full contents of the System SD card can be copied to the Optional SD card while the B5800
Branch Gateway system is running.
• The write lock setting on cards in the Optional SD card slot is honored.
Warning:
Memory cards should always be shut down before being removed when the system is running. Though the card slot LEDs indicate when data is being written to a card, lack of flashing LEDs is not a sufficient safeguard. Shutting down the card will disable embedded voicemail if being used. If the System SD card is removed, features licensed by the card's Feature Key serial number will continue operating for up to 2 hours.
Card maintenance
Using Manager, the System Status application, or a phone configured as a system phone, you can perform the following procedure on the SD cards.
Procedure
Backing up the primary folder using Manager on
page 251
Description
Copy the files in the primary folder on the
System SD card to the/backup folder on the card.
Manage r
System
Status
System
Phone
Minut es
6
6
Restoring from the backup folder using Manager on
page 252
Copy the files in the backup folder on the
System SD card to the primary folder on the card and restart the B5800 Branch
Gateway system.
Optional SD card using Manager on
page 254
Copy all the files on the System SD card to the Optional SD card.
Upgrading using an Optional SD card on page 260
Copy the configuration file in the primary folder on the Optional SD card to the primary folder on the System SD card and then restart the B5800 Branch Gateway system.
Upload a set of B5800 Branch Gateway software and embedded voicemail prompts to the System SD card.
–
–
–
–
90
15
40
244 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Procedure Description Manage r
System
Status
System
Phone
Minut es
page 259
on page 250
View the folders and files on the control unit memory cards.
– – –
The following procedures can be performed on cards in an SD card reader on a PC running
Manager.
Formatting an SD card on page 248
Reformat a card for B5800 Branch
Gateway use without removing the Feature
Key serial number.
– 1
Caution:
This process will erase all existing files on the card.
Create the folder structure on a memory card and copy a set of B5800 Branch
Gateway software files into those folders.
– – 15
Card specification
Non-Avaya cards can be used in the Optional SD card slot as long as they match or exceed the following standard:
SDHC 4GB minimum Class 2+. Single partition FAT32 format.
SD card folders
The System SD card contains the following folders:
• primary — contains the firmware files for the control unit, external expansion modules and supported phones. The folder can also contain music on hold files and license key files. This is the main set of files used by the B5800 Branch Gateway system when booting up. It also contains the stored copy of the B5800 Branch Gateway configuration.
• backup — contains a copy of the primary folder at some previous point. A backup copy of the primary contents to this folder can be invoked manually (using Manager or SSA) or as part of the B5800
Branch Gateway software upgrade using Manager.
• lvmail — a sub-folder that is used to store individual user and group mailbox messages, name recordings and announcements used by Embedded Voicemail. The storage capacity for Embedded
Voicemail is limited to 15 hours regardless of the capacity of the card. Mailbox messages and greetings are stored in a sub-folder of the /dynamic folder.
• AAG — a sub-folder that is used to store embedded voicemail auto-attendant greetings.
• doc — contains initial installation documentation for B5800 Branch Gateway .
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 245
SD card management
• dynamic — contains files used by the B5800 Branch Gateway and retained through a reboot of the
B5800 Branch Gateway system.
• temp — contains temporary files used by the B5800 Branch Gateway and not retained through a reboot of the B5800 Branch Gateway system.
The Optional SD card can contain a similar set of folders as the System SD card. The Optional SD card folders are used as an additional backup or they can be used as the source for upgrading the contents of the System SD card.
Booting from the SD cards
When being powered up, the control unit looks for a valid .bin binary file to load. It does this using the possible source below in the order shown, skipping to the next source if the file is not present or is not valid.
1. System SD card primary folder.
2. The control unit's own internal non-volatile memory. Once a system has been installed, it uses its non-volatile memory to keep copies of the configuration and system binary files it is using. These can be used to restore operation during a system reboot. Note that though a system can boot from non-volatile memory, a
System SD card must still be present for correct system operation.
3. System SD card backup folder.
4. Optional SD card primary folder.
5. Optional SD card backup folder.
6. If no file is found, the control unit will fallback to making BOOTP requests to the network. Manager can respond to the BOOTP request. See
About erasing the operational firmware on page 237 for more information.
Once a valid .bin file is found, the control unit loads that firmware. The source from which the control unit binary file was loaded is then used to load further files.
Configuration file loading
After the system firmware files are installed, a configuration file must be installed on the control unit.
• If the control unit booted using binary files from an SD card location, it looks for a valid configuration file in the same location.
- If a configuration file is present and valid, it is loaded.
- If a configuration file is present but is not valid, load the configuration copy in its nonvolatile memory if present. Otherwise, the control unit will have a default configuration.
246 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Booting from the SD cards
- If a configuration file is not present, use the non-volatile memory copy unless the reboot is as a result of a default system command.
• If the control unit booted using binary files from its non-volatile memory, it will also load the configuration copy from that location.
- It will indicate a boot alarm (see Boot alarms below).
- It will attempt to restore the firmware file in the System SD card /primary folder using the copy in its non-volatile memory.
- The normal boot-up process of upgrading expansion module firmware does not occur. If the File > Advanced > Upgrade command is used, only external expansion modules actually present in the system are listed for upgrade.
Post boot operation
During normal operation, configuration and binary files sent to the System SD card /primary folder using Manager are also written to the non-volatile memory.
If the system has booted from its non-volatile memory due to an SD card problem, it is still possible to upgrade the .bin file using the B5800 Branch Gateway upgrade wizard. See
System upgrade using the System SD card on page 258 for more information.
Boot alarms
The following apply if the control unit boots up using software other than that in its System SD primary folder:
• An alarm will be shown in the System Status application. It will also generate an alarm if the card in any slot is not compatible. These alarms are also output as SNMP, Syslog or email alarms.
• The Manager Select IP Office window will display an icon indicating that the system is running using software other than from the System SD card's primary folder.
• The configuration can be read but will be read only. Attempting to send a configuration to the system will cause the error message Failed to save configuration data.
(Internal error) .
Bypassing the System SD card primary folder
The control unit can be forced to bypass the System SD card's primary folder and non-volatile memory when starting. This is done by pressing the AUX button while applying power to the control unit. This may be necessary if, following an upgrade of the B5800 Branch Gateway system, it is determined that a roll back to the previously backed up firmware and configuration is required. Using the AUX button should restore system operation using the backup folder files while the installer then restores the contents of the primary folder to a previous release.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 247
SD card management
About creating a B5800 Branch Gateway SD card
The procedures in this section are for B5800 Branch Gateway SD cards for use in the System
SD card slot. They can also be applied to non-Avaya SD cards for use in the Optional SD card slot. For the System SD card slot, only Avaya SD cards with a Feature Key should be used.
The card must be in the following format:
SDHC 4GB minimum Class 2+. Single partition FAT32 format.
Warning:
Avaya supplied SD cards should not be formatted using any other method than the format commands within Manager and the System Status application. Formatting the cards using any other method will remove the feature key used for B5800 Branch Gateway licensing from the card.
These procedures are run on an SD card inserted in a card reader on the Manager PC. That card can then be used in the System SD card slot of a new system or in the Optional SD card slot of an existing system to upgrade that system.
Formatting an SD card
Before you begin
To enable this option, the working directory defined in File > Preferences > Directories must be set to the parent directory of the Memory Cards folder.
About this task
Avaya SD cards should only be formatted using the format options provided within the B5800
Branch Gateway applications.
Warning:
This procedure will erase any existing files and folders on the card.
Procedure
1. Start Manager.
2. Insert the SD card into a reader slot on the Manager PC.
3. Select File > Advanced > Format IP Office SD Card > Avaya B5800 Branch
Gateway.
4. Browse to the card location and click OK.
248 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
About creating a B5800 Branch Gateway SD card
The status bar at the bottom of Manager displays the progress of the formatting process.
5. When the formatting is complete, load the B5800 Branch Gateway folders and files
onto the card from the Manager PC. See Recreating an SD card
on page 249.
Formatting a System SD card using the System Status application
Procedure
1. Start the System Status application and access the System Status output.
2. In the navigation panel, select System > Memory Cards > System SD.
3. Click on the Format button at the bottom of the screen.
The card is reformatted. All files and folders on the card will be deleted. This process takes a few seconds.
Recreating an SD card
Before you begin
To enable this option, the working directory defined in File > Preferences > Directories must be set to the parent directory of the Memory Cards folder.
Be sure to back up the PLDSKeys.xml file in the primary folder before you perform this task.
When you perform this task, the PLDSKeys.xml file is deleted.
About this task
This procedure creates the folder structure on the SD card and copies the required firmware files from those installed with Manager onto the SD card. This includes the binary files for the system, any external expansion modules, and phones. It also includes the prompt files for embedded voicemail operation.
This procedure can be used to upgrade an existing SD card to match the file set installed with
Manager. For the card to be used in the System SD card slot, the card must be an Avaya SD
Feature Key card. The card must be correctly formatted. See Formatting an SD card
on page 248.
If the card contains any dynamic system files, for example SMDR records, they are temporarily backed up by Manager and then restored after the card is recreated. This procedure takes approximately 15 minutes.
Procedure
1. Insert the SD card into a card reader on the Manager PC.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 249
SD card management
Note:
Do not remove the SD card. Removing the SD card will interrupt the upgrade.
2. Select File > Advanced > Recreate IP Office SD Card > Avaya B5800 Branch
Gateway.
3. Browse to the card location and click OK.
Manager starts creating folders on the SD card and copying the required files into those folders. This process takes approximately 15 minutes. Do not remove the SD card until Manager shows a message that the recreation has finished.
Viewing the card contents
About this task
Using Manager you can view the folders and files on the System SD card and the Optional SD card.
Procedure
1. Start Manager.
2. Select File > Embedded File Management.
3. From the Select IP Office window, select the B5800 Branch Gateway system you want to view.
The file contents of the memory cards are displayed.
About backing up the System SD card
There are two levels of backup that can be performed.
• Backup the System SD card primary folder — The contents of the primary folder on the System SD card are copied to the backup folder on the System SD. This can be performed remotely.
• Backup all files on the System SD card — The contents of the primary folder, backup folder, and embedded voicemail files including message files on the System SD card are copied to the Optional SD card. This can be performed remotely. However, the contents can only be copied back manually using a card reader.
250 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
About backing up the System SD card
Note:
The backup, restore, and copy operations will not be performed if the destination card has insufficient space for the files being copied.
Backing up the primary folder using Manager
About this task
This procedure copies the contents of the primary folder on the System SD card to the backup folder on the System SD card. Files with matching file names are replaced. This procedure takes approximately 6 minutes.
Procedure
1. Start Manager.
2. Select File > Embedded File Management.
3. From the Select IP Office window, select the appropriate system.
The file contents of the memory cards are displayed.
4. Select File > Backup System Files.
The contents of the primary folder on the System SD card are copied to the backup folder. This process takes approximately 6 minutes.
Backing up the primary folder using the System Status application
Procedure
1. Start the System Status application and access the B5800 Branch Gateway status output.
2. In the navigation panel select System.
3. At the bottom of the screen select Backup System Files.
The contents of the primary folder on the System SD card are copied to the backup folder. This process takes approximately 6 minutes.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 251
SD card management
Backing up the primary folder using a system phone
About this task
A user configured as a system phone user can perform this procedure using a 1400, 1600, or
9600 Series phone (excluding XX01, XX02 and XX03 models). The user's login code is used to restrict access to system administration functions on the phone.
Procedure
1. Select Features > Phone User > System Admin.
2. Enter your B5800 Branch Gateway user login code.
3. From the menu select Memory Card.
4. Select System Backup.
The contents of the primary folder on the System SD card are copied to the backup folder. This process takes approximately 6 minutes.
About restoring from the backup folder
When you restore from the backup folder, you copy the contents of the backup folder on the
System SD card to the primary folder on the System SD card. Files with matching file names are replaced.
Warning:
This procedure will cause the B5800 Branch Gateway system to be restarted, disconnecting any current calls and services in progress.
Restoring from the backup folder using Manager
Procedure
1. Start Manager.
2. Select File > Embedded File Management.
3. From the Select IP Office window, select the appropriate system.
The file contents of the memory cards are displayed.
4. Select File > Restore System Files.
The contents of the backup folder on the System SD card are copied to the primary folder on the System SD card. The process takes approximately 6 minutes. When
252 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
About restoring from the backup folder the process has been completed, the B5800 Branch Gateway system is restarted.
Restoring from the backup folder using the System Status application
Procedure
1. Start the System Status application and access the B5800 Branch Gateway status output.
2. In the navigation panel select System.
3. At the bottom of the screen select Restore System Files.
The contents of the backup folder on the System SD card are copied to the primary folder on the System SD card. The process takes approximately 6 minutes. When the process has been completed, the B5800 Branch Gateway system is restarted.
Restoring from the backup folder using a system phone
About this task
A user configured as a system phone user can perform this procedure using a 1400, 1600, or
9600 Series phone (excluding XX01, XX02 and XX03 models). The user's login code is used to restrict access to system administration functions on the phone.
Procedure
1. Select Features > Phone User > System Admin.
2. Enter your B5800 Branch Gateway user login code.
3. From the menu select Memory Card.
4. Select System Restore.
The contents of the backup folder on the System SD card are copied to the primary folder on the System SD card. The process takes approximately 6 minutes. When the process has been completed, the B5800 Branch Gateway system is restarted.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 253
SD card management
About backing up to the Optional SD card
Backing up to the Optional SD card copies all files on the System SD card to the Optional SD card. This includes contents of the primary folder, backup folder, and embedded voicemail files including message files. Matching files and folders on the Optional SD card are overwritten.
Any files already copied that change while this process is running are not recopied. Any new files added (for example voicemail messages) while the process is running may not be copied.
Backing up to the Optional SD card takes at least 90 minutes and may take much longer depending on the amount of data to be copied. For example, it will take longer if embedded voicemail is being used by the B5800 Branch Gateway system to take messages.
Backing up to the Optional SD card using Manager
Procedure
1. Start Manager.
2. Select File > Embedded File Management.
3. From the Select IP Office window, select the appropriate system.
The file contents of the memory cards are displayed.
4. Select File > Copy System Card.
The contents of the System SD card are copied to the Optional SD card. This takes at least 90 minutes and can take much longer.
Backing up to the Optional SD card using the System Status application
Procedure
1. Start the System Status application and access the B5800 Branch Gateway status output.
2. In the navigation panel select System.
3. Select Memory Cards.
4. Select System Card.
254 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
About restoring from the Optional SD card
5. At the bottom of the screen select Copy System Card.
The contents of the System SD card are copied to the Optional SD card. This takes at least 90 minutes and can take much longer.
Backing up to the Optional SD card using a system phone
About this task
A user configured as a system phone user can perform this procedure using a 1400, 1600, or
9600 Series phone (excluding XX01, XX02 and XX03 models). The user's login code is used to restrict access to system administration functions on the phone.
Procedure
1. Select Features > Phone User > System Admin.
2. Enter your B5800 Branch Gateway user login code.
3. From the menu select Memory Card.
4. Select Copy.
The contents of the System SD card are copied to the Optional SD card. This takes at least 90 minutes and can take much longer.
About restoring from the Optional SD card
The files in the primary folder on the Optional SD card can be copied to the primary folder on the System SD card. Files with matching file names are replaced.
There are two levels of restore that can be performed:
• Restoring only configuration files from the Optional SD card — Only the configuration file config.cfg and the licenses file keys.txt are copied from the Optional SD card to the System SD card.
• Restoring only software files from the Optional SD card — All files in the primary folder except the configuration file config.cfg and licenses file keys.txt are coped from the
Optional SD card to the System SD card. This process does not restore embedded voicmail prompts. This process takes approximately 5 minutes.
Being able to restore just the software files allows software files to be copied from an Optional
SD card without affecting the existing configuration of that system.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 255
SD card management
Warning:
This procedure will cause the B5800 Branch Gateway system to be restarted, disconnecting any current calls and services in progress.
Restoring a configuration file from the Optional SD card using
Manager
Procedure
1. Start Manager.
2. Select File > Embedded File Management.
3. From the Select IP Office window, select the appropriate system.
The file contents of the memory cards are displayed.
4. Select File > Upgrade Configuration.
The configuration file config.cfg and licenses file keys.txt in the primary folder on the Optional SD card are copied to the primary folder on the System SD card. This takes a few seconds. When the process has been completed, the B5800 Branch
Gateway system is restarted.
Restoring a configuration file from the Optional SD card using a system phone
About this task
A user configured as a system phone user can perform this procedure using a 1400, 1600, or
9600 Series phone (excluding XX01, XX02 and XX03 models). The user's login code is used to restrict access to system administration functions on the phone.
Procedure
1. Select Features > Phone User > System Admin.
2. Enter your B5800 Branch Gateway user login code.
3. From the menu select Memory Card.
4. Select Upgrade Config.
The configuration file config.cfg and licenses file keys.txt in the primary folder on the Optional SD card are copied to the primary folder on the System SD card. This
256 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
About restoring from the Optional SD card takes a few seconds. When the process has been completed, the B5800 Branch
Gateway system is restarted.
Restoring software files from the Optional SD card using Manager
Procedure
1. Start Manager.
2. Select File > Embedded File Management.
3. From the Select IP Office window, select the appropriate system.
The file contents of the memory cards are displayed.
4. Select File > Upgrade Binaries.
All files in the primary folder on the Optional SC card except the configuration file config.cfg and licenses file keys.txt are copied to the primary folder on the System
SD card. This takes approximately 5 minutes. When the process has been completed, the B5800 Branch Gateway system is restarted.
Restoring software files from the Optional SD card using a system phone
About this task
A user configured as a system phone user can perform this procedure using a 1400, 1600, or
9600 Series phone (excluding XX01, XX02 and XX03 models). The user's login code is used to restrict access to system administration functions on the phone.
Procedure
1. Select Features > Phone User > System Admin.
2. Enter your B5800 Branch Gateway user login code.
3. From the menu select Memory Card.
4. Select Upgrade Binaries.
All files in the primary folder on the Optional SC card except the configuration file config.cfg and licenses file keys.txt are copied to the primary folder on the System
SD card. This takes approximately 5 minutes. When the process has been completed, the B5800 Branch Gateway system is restarted.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 257
SD card management
System upgrade using the System SD card
In addition to using the upgrade wizard (see
Using the upgrade wizard on page 219), control
units can be upgraded by loading the required firmware files onto the System SD card and rebooting the system. There are several ways to load the required firmware onto the System
SD card as described in the table below.
Note:
• Check the latest B5800 Branch Gateway Technical Bulletin for the B5800 Branch
Gateway software release before proceeding any further. It may contain information relating to changes that occurred after this document was completed. Bulletins are available from http://support.avaya.com
• Some upgrades may require entry of upgrade licenses.
Warning:
This procedure will cause the system to be restarted, disconnecting any current calls and services in progress.
Method Description Location Software
Files
Embedded
Voicemail
Prompts
page 259
on page 259
on page 260
Using Manager, the contents of the card are compared to the files that Manager has available and are upgraded if necessary.
Local or
Remote
In this method, the System
SD card is shut down and removed from the control unit. The card's contents are upgraded using Manager.
Local
This method uses an SD card loaded with the required version of B5800 Branch
Gateway software. The card is inserted into the control unit and then Manager,
System Status or a system phone is used to transfer the software to the System SD card.
Local –
258 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
System upgrade using the System SD card
Upgrading remotely using Manager
About this task
This procedure copies all system files not present or of a different version compared to those already present on the System SD card.
Procedure
1. Start Manager.
2. Select File > Embedded File Management.
3. From the Select IP Office window, select the appropriate system.
The file contents of the memory cards are displayed.
4. Select File > Backup System Files.
The contents of the primary folder on the System SD card are copied to the backup folder. This process takes approximately 6 minutes.
5. Select File > Upload System Files.
Manager uploads the system files to the primary folder on the System SD card. This includes B5800 Branch Gateway software files and embedded voicemail prompt files. Depending on the files that need to be updated, this can take up to40 minutes.
Upgrading the SD card locally
About this task
You can upgrade the SD card locally if you have physical access to the control unit. This method should be used with a timed reboot, allowing the card upgrade to be done during normal
operation hours followed by a reboot outside of normal operation hours. See Rebooting the system
on page 210 for more information.
If the card is being used for embedded voicemail, that service is not available while the card is shutdown. Licensed features however will continue running for up to 2 hours while the card is shutdown.
Procedure
2. Create the SD card. See
About creating a B5800 Branch Gateway SD card on
page 248.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 259
SD card management
This procedure overwrites the software files on the card with the files available in
Manager. It will not affect any other files, for example the configuration file. This process takes approximately 15 minutes.
3. Reinsert the card into the System SD card slot on the control unit.
4. Using Manager, select File > Advanced > Reboot.
5. In the Select IP Office window, select the appropriate system and click OK.
6. Select the type of reboot you want to perform and click OK.
When the system reboots, the software files are loaded in the primary folder of the
System SD card.
Upgrading using an Optional SD card
About this task
This method allows an Optional SD card to be used as the source from which the System SD card is upgraded. It only upgrades the software files, it does not update embedded voicemail prompts.
Procedure
1. Insert the SD card into a card reader on the Manager PC.
Note:
Do not remove the SD card. Removing the SD card will interrupt the upgrade.
2. Using Manager, select File > Advanced > Recreate IP Office SD Card.
3. Select one of the following:
• IP Office A-Law
• IP Office U-Law
This selection determines how the system operates when defaulted with the SD card installed in the System SD card slot.
4. Browse to the card location and click OK.
Manager starts creating folders on the SD card and copying the required files into those folders. This process takes approximately 15 minutes. Do not remove the SD card until Manager shows a message that the recreation has finished.
5. Insert the card into the Optional SD card slot on the control unit.
6. Use one of the following procedures to copy the software from the Optional SD card to the System SD card:
• See
Restoring software files from the Optional SD card using Manager
on page 257.
260 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Memory card removal
• See
Restoring software files from the Optional SD card using a system phone on page 257.
Memory card removal
Warning:
Memory cards should always be shut down before being removed when the system is running. Though the card slot LEDs indicate when data is being written to a card, lack of flashing LEDs is not a sufficient safeguard. Shutting down the card will disable embedded voicemail if being used. If the System SD card is removed, features licensed by the card's
Feature Key serial number will continue operating for up to 2 hours.
Card services can be restarted by either reinserting the card or using a Start Up command.
Shutting down a memory card using Manager
Procedure
1. From the System Manager console, select the B5800 Branch Gateway device and click Edit to edit the system configuration for the device. IP Office Manager will be launched on your PC. For more information, see
Editing a B5800 Branch Gateway system configuration from System Manager on page 159.
2. Select File > Advanced > Memory Card Command > Shutdown.
The following prompt appears: Shutting down a memory card may cause service loss. Continue?
3. Click Yes.
4. In the Select IP Office window, click the check box for the appropriate system.
5. Click OK.
6. At the back of the control unit, confirm that the appropriate memory card LED is off.
7. Remove the card.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 261
SD card management
Shutting down a memory card using a system phone
About this task
To shut down a memory card using a system phone, you must be administered as a System
Phone user. You can shut down a memory card using a 1400, 1600, or 9600 series phone.
Your Login Code is used to restrict access to some system administration functions on the phone.
Procedure
1. Select Features > Phone User > System Admin.
2. Enter your B5800 Branch Gateway user login code.
3. Select Memory Card.
4. Select System for the System SD card or Option for the Optional SD card.
5. Select Shutdown.
6. At the back of the control unit, confirm that the appropriate memory card LED is off.
7. Remove the card.
Shutting down a memory card using System Status
Procedure
1. Open System Status and access the status output.
2. In the navigation pane, select System > Memory Cards.
3. Click System SD or Optional SD.
4. At the bottom of the window, click Shutdown.
5. At the back of the control unit, confirm that the appropriate memory card LED is off.
6. Remove the card.
262 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Memory card startup
Memory card startup
Reinserting a memory card into a system that is already switched on will automatically restart card operation. However, if the card has been shutdown but not removed, it can be restarted without requiring a reboot.
Starting up a memory card using Manager
About this task
Use this task to restart a memory card without removing and reinserting it.
Perform this task using IP Office Manager that is installed on a PC for the branch. You cannot perform this task from Manager that is accessed from System Manager. If the B5800 Branch
Gateway is centrally managed by System Manager, you must disable the System Manager administration feature for the branch (by disabling Under SMGR Administration in Security
Settings) before you perform this task. For more information, see “Disabling the System
Manager administration feature for the branch” in Implementing the B5800 Branch Gateway for an Avaya Aura
®
Configuration, document number 18-603853.
Procedure
1. Open IP Office Manager and receive the B5800 Branch Gateway configuration.
2. Select File > Advanced > Memory Card Command > Startup.
3. In the Select IP Office window, click the check box for the appropriate system.
4. Click OK.
Starting up a memory card using System Status
About this task
Use this task to restart a memory card without removing and reinserting it.
Procedure
1. Open System Status and access the status output.
2. In the navigation pane, select System > Memory Cards.
3. Click System SD or Optional SD.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 263
SD card management
4. At the bottom of the window, click Startup.
Starting up a card using a system phone
About this task
A user configured as a system phone user can perform this procedure using a 1400, 1600, or
9600 Series phone (excluding XX01, XX02 and XX03 models). The user's login code is used to restrict access to system administration functions on the phone.
Procedure
1. Select Features > Phone User > System Admin.
2. Enter your B5800 Branch Gateway user login code.
3. From the menu select Memory Card.
4. Choose one of the following:
• Select System for the System SD card
• Select Option for the Optional SD card.
5. Select Startup.
264 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Chapter 18: Safety and regulatory information
Safety statements
The B5800 Branch Gateway modules are intended to be installed by Service Personnel and it is the responsibility of the Service Personnel to ensure that all subsidiary interconnected equipment is wired correctly and also meet the safety requirements of IEC60950 or UL60950 where applicable.
•
The CE mark affixed to this equipment means that the module complies with the 1999/5/
EC (R&TTE), 89/336/EEC (EMC) and 72/23EEC (LVD) Directives.
• The Declarations of Conformity (DoC) for the B5800 Branch Gateway products are available on the B5800 Branch Gateway Application DVD.
•
Warning:
This warning symbol is found on the base of B5800 Branch Gateway modules.
• Refer to
on page 267 for information concerning which trunk interface module variants are fitted in which country.
In Finland, Norway and Sweden a protective earthing conductor must be attached to the
protective earth point on the rear of the servers. See Grounding
on page 73 for more information. In addition, the server must be located in a restricted access location where equipotential bonding has been applied, for example, in a telecommunication center.
Important safety instructions when using your telephone equipment
When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following:
• Do not use this product near water, for example, near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool.
• Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 265
Safety and regulatory information
• Do not use the telephone to report a gas leak in the vicinity of the leak.
• Use only the power cord and batteries indicated in this manual.
Lithium batteries
A lithium battery is fitted to the real time clock on the control unit motherboard.
Warning:
The Lithium battery must only be replaced by Avaya personnel or authorized representatives. There is a danger of explosion if the battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions.
Lightening protection/hazard symbols
Lightning protectors — The buildings lightning protectors must be verified as follow:
1. Check the lightning protectors at the trunk cable entry point to the building housing the B5800 Branch Gateway system , paying special attention to the lightning protection grounding. Report any problems, in writing, to the telephone company.
2. Equipment that is designed to be connected using internal wiring is typically not lightning protected. Hence, B5800 Branch Gateway extension cabling must not leave the building. For installations where telephones and/or other standard (tip/ ring) devices are installed in another building then lightning protection is required, see
Out of Building Telephone Installations
on page 74.
Hazard Symbol — The shock hazard symbol is intended to alert personnel to electrical hazard or equipment damage. The following precautions must also be observed when installing telephone equipment:
• Never install telephone wiring during a lightning storm.
• Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations.
• Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface.
• Always use caution when working with telephone lines.
266 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Safety statements
Trunk interface modules
To ensure the validation of the approvals, only the following types of trunk interface cards must be fitted in the B5800 Branch Gateway control unit.
Product Quad
BRI
Control unit
USA/Canada
PRI E1
Single Dual
PRI T1
Single Dual
ATM4 WAN
Product Quad
BRI
Control unit
Rest of World
PRI E1/E1R2 PRI T1
Single Dual Single Dual
ATM4 WAN
Note:
E1R2 trunks are only supported in CALA and Korea.
Port safety classification
The B5800 Branch Gateway systems have the following ports which are classified as follows:
PRI port
Port Name
BRI ports
Analog ports
Power fail ports
DTE port
Analog telephone ports
Digital telephone ports
WAN port
LAN ports
Port Description Port Classification
PRI ISDN connection (NET) TNV (Operating within the limits of SELV)
BRI ISDN connection (NET) TNV (Operating within the limits of SELV)
Two wire analog trunk TNV3
Two wire analog trunk
Async Data connection.
TNV3
SELV
Telephone Extension ports TNV2
Telephone Extension ports SELV
WAN connection (NET).
10/100 BaseT attachment to
LAN.
SELV
SELV
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 267
Safety and regulatory information
Port Name
Expansion ports
Audio port
External control port
DC input port
Port Description
Expansion Module connector.
Connector for Music on
Hold.
Connector for Controlling
Ancillary circuits.
Connector for DC input power.
Port Classification
SELV
SELV
SELV
SELV
Interconnection circuits shall be selected to provide continued conformance with the requirements of EN 609050:1992/A3:1995 clause 2.3 for SELV circuits and with the requirements of clause 6 for TNV circuits, after connections between equipment.
EMC cautions
889/336/ EEC (EMC Directive) CISPR 22:1993 including A1 + A2, AS/NZ 3548:1995 (ROW)
Warning:
This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.
Federal communications commission (FCC)
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his or her own expense.
Canadian department of communications (DOC)
''NOTICE: This equipment meets the applicable Industry Canada Terminal Equipment
Technical Specifications. This is confirmed by the registration number. The abbreviation, IC, before the registration number signifies that registration was performed based on a Declaration of Conformity indicating that Industry Canada technical specifications were met. It does not imply that Industry Canada approved the equipment."
268 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Regulatory Instructions for Use
EMC caution for china
Regulatory Instructions for Use
Australia
BRI interface
During the configuration, ensure "000" emergency number is not barred, by performing the following:
• Short Code: 000
• Telephone No: 000;
• Function: DialEmergency
Connections to TS013, the following bearer capabilities shall not be used: 7kHz Audio, Video,
Restricted Digital Information.
If unknown type of number is used in calling party number, the network will use the default
CLI.
The system must be configured for Point to Multi point connection to comply with Austel requirements for connecting to TS013 circuits.
As the B5800 Branch Gateway does not support emergency dialing after loss of power, the following warning notice should be recognized:
Warning:
This equipment will be inoperable when main power fails.
PRI interface
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 269
Safety and regulatory information
During the configuration, ensure "000" emergency number is not barred, by performing the following:
• Short Code: 000
• Telephone No: 000;
• Function: DialEmergency
Canada
This equipment meets the applicable Industry Canada Terminal Equipment Technical
Specifications. This is confirmed by the registration number. The abbreviation, IC, before the registration number signifies that registration was performed based on a Declaration of
Conformity indicating that Industry Canada technical specifications were met.
It does not imply that Industry Canada approved the equipment.
''NOTICE: The Ringer Equivalence Number (REN) for this terminal equipment is 1. The REN assigned to each terminal equipment provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the
Ringer Equivalence Numbers of all the devices does not exceed five.''
270 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
China
Regulatory Instructions for Use
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 271
Safety and regulatory information
European Union
• 999 and 112 calls must not be barred. Doing so will invalidate the approval.
• All connections at the MDF shall be identifiable by suitable labeling.
• The CE mark displayed on B5800 Branch Gateway equipment indicates the systems compliance with the EMC, LVD, and R&TTE Directives and common technical regulations for Primary Rate and Basic Rate ISDN.
• All ports for the connection of other non-telecommunications apparatus have a Safety
Extra Low Voltage (SELV) safety status.
New Zealand
The grant of a Telepermit for any item of terminal equipment indicates only that Telecom has accepted that the item complies with minimum conditions for connection to its network. It indicates no endorsement of the product by Telecom, nor does it provide any sort of warranty.
Above all, it provides no assurance that any item will work correctly in all respects with another item of Telepermitted equipment of a different make or model, nor does it imply that any product is compatible with all of Telecom's network services.
FCC notification
This equipment complies with Part 68 of the FCC rules and the requirements adopted by the
Administrative Council on Terminal Attachments (ACTA). On the rear of this equipment is a label that contains, among other information, a product identifier in the format
US:AAAEQ##TXXX. If requested, this number must be provided to the telephone company.
The REN is used to determine the quantity of devices that may be connected to the telephone line. Excessive RENs on the telephone line may result in devices not ringing in response to an incoming call. In most, but not all areas, the sum of RENs should not exceed 5.0. To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact the local telephone company. For products approved after July 23, 2001, the REN for this product is part of the product identifier that has the format US:AAAEQ##TXXX. The digits represented by ## are the REN without a decimal point (for example, 03 is a REN of 0.3). For earlier products, the REN is separately shown on the label.
Means of connection
Connection of this equipment to the telephone network is shown in the following table.
272 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Regulatory Instructions for Use
Port
IPO500 PRI 1U,
IPO500 PRI2U,
IP400 PRI-T1
FIC
04DU9.BN,
04DU9.DN,
04DU9.IKN,
04DU9.ISN
IPO500 ATM4U
IP400 ATM4U
OL13A, OL13B,
OL13C, 02AC2,
02LA2, 02LB2,
02LC2, 02LR2,
02LS2
IPO500 ATM16 OL13A, OL13B,
OL13C,
02AC2, 02GS2,
02LA2, 02LB2,
02LC2, 02LR2,
02LF2
02GS2, 02LS2
6.0Y
9.0Y
9.0Y
SOC USOC Jack
RJ48C NA
REN
RJ45S
RJ45S
0.1B
0.1B
If this equipment causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. But if advance notice is not practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary.
The telephone company may make changes in its facilities, equipment, operations or procedures that could affect the operation of the equipment. If this happens, the telephone company will provide advance notice in order for you to make necessary modifications to maintain uninterrupted service.
If trouble is experienced with this equipment, for repair or warranty information, please contact the Technical Service Center at 1-800-242- 2121 or contact your local Avaya representative.
If the equipment is causing harm to the telephone network, the telephone company may request that you disconnect the equipment until the problem is resolved.
A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA.
Connection to party line service is subject to state tariffs. Contact the state public utility commission, public service commission or corporation commission for information.
Equipment with Direct Inward Dialing (DID)
Allowing this equipment to be operated in such a manner as to not provide proper answer supervision is a violation of Part 68 of the FCC’s rules.
Proper answer supervision is when:
• This equipment returns answer supervision to the public switched telephone network
(PSTN) when DID calls are:
- Answered by the called station
- Answered by the attendant
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 273
Safety and regulatory information
- Routed to a recorded announcement that can be administered by the customer premises equipment (CPE) user
- Routed to a dial prompt
• This equipment returns answer supervision signals on all DID calls forwarded back to the
PSTN. Permissible exceptions are:
- A call is unanswered.
- A busy tone is received.
- A reorder tone is received.
Avaya attests that this registered equipment is capable of providing users access to interstate providers of operator services through the use of access codes. Modification of this equipment by call aggregators to block access dialing codes is a violation of the Telephone Operator
Consumers Act of 1990.
Automatic dialers
When programming emergency numbers and (or) making test calls to emergency numbers:
• Remain on the line and briefly explain to the dispatcher the reason for the call.
• Perform such activities in the off-peak hours, such as early morning or late evenings.
Toll restriction and least cost routing equipment
The software contained in this equipment to allow user access to the network must be upgraded to recognize newly established network area codes and exchange codes as they are placed into service.
Failure to upgrade the premises systems or peripheral equipment to recognize the new codes as they are established will restrict the customer and the customer’s employees from gaining access to the network and to these codes.
FCC part 68 supplier’s declarations of conformity
Avaya Inc. in the United States of America hereby certifies that the equipment described in this document and bearing a TIA TSB-168 label identification number complies with the FCC’s
Rules and Regulations 47 CFR Part 68, and the Administrative Council on Terminal
Attachments (ACTA) adopted technical criteria.
Avaya further asserts that Avaya handset-equipped terminal equipment described in this document complies with Paragraph 68.316 of the FCC Rules and Regulations defining Hearing
Aid Compatibility and is deemed compatible with hearing aids.
Compliance with FCC rules
Transmit and receive gain settings for PRI/T1 and analog ports
The Gain settings are password controlled for use by qualified installation personnel only and must not be made available to the end user. The default gain settings of 0dB ensures compliance with FCC part 68 section 68.308(b)(5) and TIA/EIA-IS-968 Section 4.5.2.5.
"Through transmission amplification from ports for the connection of separately registered equipment or from other network connection ports". Gain setting adjustment by unqualified
274 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Regulatory Instructions for Use personnel may result in violation of the FCC rules. Qualified personnel may adjust gain settings above these levels only where:
• Measurement is made to ensure that the power levels sent to line at each network interface connected does not exceed the maximum levels specified in FCC part 68 section
68.308(b) and TIA/EIA-IS-968 Section 4.5 for that specific interface type.
• Where gain adjustment away from the default values are made, precautions should be taken to ensure that the connection of terminal equipment is controlled by qualified installation personnel.
• To conform with the Receive Objective Loudness Rating at distances greater than 2.7km
from the central office, on analog trunks a receive gain of 1.5dB must be set.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 275
Safety and regulatory information
276 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Appendix A: Avaya port matrix for B5800
Branch Gateway and SIP phones
This appendix provides example ingress and egress ports for B5800 Branch Gateway and SIP phones.
What are ports and how are they used?
TCP and UDP use ports (defined at http://www.iana.org/assignments/port-numbers ) to route traffic arriving at a particular IP device to the correct upper layer application. These ports are logical descriptors (numbers) that help devices multiplex and de-multiplex information streams.
Consider your desktop PC. Multiple applications may be simultaneously receiving information.
In this example, email may use destination TCP port 25, a browser may use destination TCP port 80 and a telnet session may use destination TCP port 23. These logical ports allow the
PC to de-multiplex a single incoming serial data packet stream into three mini-streams inside the PC. Furthermore, each of the mini-streams is directed to the correct high-level application because the port numbers identify which application each data mini-stream belongs. Every IP device has incoming (Ingress) and outgoing (Egress) data streams.
Ports are used in TCP and UDP to name the ends of logical connections which carry data flows. TCP and UDP streams have an IP address and port number for both source and destination IP devices. The pairing of an IP address and a port number is called a socket
(discussed later). Therefore, each data stream is uniquely identified with two sockets. Source and destination sockets must be known by the source before a data stream can be sent to the destination. Some destination ports are “open” to receive data streams and are called
“listening” ports. Listening ports actively wait for a source (client) to make contact to a destination (server) using a specific port that has a known protocol associate with that port number. HTTPS, as an example, is assigned port number 443. When a destination IP device is contacted by a source device using port 443, the destination uses the HTTPS protocol for that data stream conversation.
Port type ranges
Port numbers are divided into the following three ranges:
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 277
Avaya port matrix for B5800 Branch Gateway and SIP phones
• Well known ports are those numbered from 0 through 1023.
• Registered ports are those numbered from 1024 through 49151
• Dynamic ports are those numbered from 49152 through 65535
The well known and registered ports are assigned by IANA (Internet Assigned Numbers
Authority) and are found at http://www.iana.org/assignments/port-numbers .
Well known ports
For the purpose of providing services to unknown clients, a service listen port is defined. This port is used by the server process as its listen port. Common services often use listen ports in the well known port range. A well known port is normally active meaning that it is “listening” for any traffic destined for a specific application. For example, well known port 23 on a server is actively waiting for a data source to contact the server IP address using this port number to establish a Telnet session. Well known port 25 is waiting for an email session, etc. These ports are tied to a well understood application and range from 0 to 1023.
In UNIX and Linux operating systems, only root may open or close a well known port. Well known ports are also commonly referred to as privileged ports.
Registered ports
Unlike well known ports, these ports are not restricted to the root user. Less common services register ports in this range. Avaya uses ports in this range for call control. Some, but not all, ports used by Avaya in this range include: 1719/1720 for H.323, 5060/5061 for SIP, 2944 for
H.248 and others. The registered port range is 1024 – 49151. Even though a port is registered with an application name, industry often uses these ports for different applications. Conflicts can occur in an enterprise when a port with one meaning is used by two servers with different meanings.
Dynamic ports
Dynamic ports, sometimes called private ports, are available to use for any general purpose.
This means there are no meanings associated with these ports (similar to RFC 1918 IP Address
Usage). These are the safest ports to use because no application types are linked to these ports. The dynamic port range is 49152 – 65535.
Sockets
A socket is the pairing of an IP address with a port number. An example would be
192.168.5.17:3009, where 3009 is the socket number associated with the IP address. A data flow, or conversation, requires two sockets – one at the source device and one at the destination device. The data flow then has two sockets with a total of four logical elements.
Each data flow must be unique. If one of the four elements is unique, the data flow is unique.
The following three data flows are uniquely identified by socket number and/or IP address.
278 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Firewall types
• Date flow 1: 172.16.16.14:1234 — 10.1.2.3:2345
• Date flow 2: 172.16.16.14:1235 — 10.1.2.3:2345
• Date flow 3: 172.16.16.14:1234 — 10.1.2.4:2345
Data flow 1 has two different port numbers and two different IP addresses and is a valid and typical socket pair.
Data flow 2 has the same IP addresses and the same port number on the second IP address as data flow 1, but since the port number on the first socket differs, the data flow is unique.
Therefore, if one IP address octet changes, or one port number changes, the data flow is unique.
Socket example showing ingress and egress data flows from a PC to a web server
Notice the client egress stream includes the client’s source IP and socket (1369) and the destination IP and socket (80). The ingress stream has the source and destination information reversed because the ingress is coming from the server.
Firewall types
There are three basic firewall types described below.
Packet filtering
Packet Filtering is the most basic form of the firewalls. Each packet that arrives or leaves the network has its header fields examined against criterion to either drop the packet or let it through. Routers configured with Access Control Lists (ACL) use packet filtering. An example of packet filtering is preventing any source device on the Engineering subnet to telnet into any device in the Accounting subnet.
Application level gateways
Application level gateways (ALG) act as a proxy, preventing a direct connection between the foreign device and the internal destination device. ALGs filter each individual packet rather than blindly copying bytes. ALGs can also send alerts via email, alarms or other methods and keep log files to track significant events.
Hybrid
Hybrid firewalls are dynamic systems, tracking each connection traversing all interfaces of the firewall and making sure they are valid. In addition to looking at headers, the content of the
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 279
Avaya port matrix for B5800 Branch Gateway and SIP phones packet, up through the application layer, is examined. A stateful inspection firewall also monitors the state of the connection and compiles the information in a state table. Stateful inspection firewalls close off ports until the connection to the specific port is requested. This is an enhancement to security against port scanning. Port scanning is the act of systematically scanning a computer's ports. Since a port is a place where information goes into and out of a computer, port scanning identifies open doors to a computer. Port scanning has legitimate uses in managing networks, but port scanning also can be malicious in nature if someone is looking for a weakened access point to break into your computer.
Firewall policies
The goals of firewall policies are to monitor, authorize and log data flows and events. They also restrict access using IP addresses, port numbers and application types and sub-types.
This appendix focuses on identifying the port numbers used by Avaya products so effective firewall policies can be created without disrupting business communications or opening unnecessary access into the network.
Knowing that the source column in the port usage tables provided below is the socket initiator is key in building some types of firewall policies. Some firewalls can be configured to automatically create a return path through the firewall if the initiating source is allowed through.
This option removes the need to enter two firewall rules, one for each stream direction, but can also raise security concerns.
Another feature of some firewalls is to create an umbrella policy that allows access for many independent data flows using a common higher layer attribute. Finally, many firewall policies can be avoided by placing endpoints and the servers that serve those endpoints in the same firewall zone.
TFTP port usage
IP Office upgrade wizard and VM Pro all use TFTP for commands and data transfer. B5800
Branch Gateway implements a version of the TFTP Transfer Identifier mechanism (TID) defined by RFC 1350.
The general mechanism is each has a TFTP listener on port 69, any received command (READ request) is responded to with a TFTP response (WRITE request) to port 69. Any subsequent data transfer uses the source ports from both request and response.
IP Office Manager (upgrade wizard)
TFTP Read, src port 2421, dst port 69 >
B5800 Branch Gateway
< TFTP Write, src port 4153, dst port 69
280 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
TFTP Acks (1..n), src port 2421, dst port
4153
Ingress ports for B5800 Branch Gateway and SIP phones
< TFTP Data packet (1..n), src port 4153, dst port 2421
Ingress ports for B5800 Branch Gateway and SIP phones
1
2
3
4
5
8
#
22
69
80
Dest.
Port
123
161-C
50802
Network
/App
Protocol
TCP/
SSH
En or
Dis
?
Default
Port
State
Remote
Device
No Open Admin terminal or
SAL
Gateway
UDP/
TFTP
No Open NM/
Manager
Ext to
Branch
Yes
Yes
?
TCP/
HTTP
UDP/
NTP
UDP/
SNMP
No Open NM/
Manager
No Open NTP
Server
Yes Closed Admin terminal or
NMS
6 5060
7 49152 –
53247-C
TCP/SIP No Open
UDP/
RTP-
RTCP
Yes Open IP Phones,
RTCP
Collector
Yes
Yes
TCP/
Who Is?
Yes Open B5800
Manager
Yes
Yes
Yes
Yes
Description
System mgmt requiring shell access – Remote maintenance.
B5800 Branch Gateway status, configuration data, program data.
on page 277 for ranges.
Web client access, Inter
B5800 Directory
Exchange (optional).
NTP (RFC4330)
Service.
Read-only access to
MIB entries.
SIP Signaling.
Dynamically allocated ports used during VoIP calls for RTP and RTCP traffic. The port range can be adjusted through the System >
Gatekeeper tab.
TCP Discovery.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 281
Avaya port matrix for B5800 Branch Gateway and SIP phones
9
# Dest.
Port
50805-C
Network
/App
Protocol
TCP/
HTTP
B5800 config access
En or
Dis
?
Default
Port
State
Remote
Device
No Open B5800
Manager
10 50808-C TCP/
HTTP
B5800
Sys
Status
Access
No Open B5800
Manager
No Open B5800
Manager
11 50813-C TCP/
HTTP
B5800
Sec
Settings
Access
OPTIONAL
I-A 68
I-B
I-C
443
1718
UDP/
DHCP-
Cli
TCP/
HTTP
TCP/
H323-
Disc
Yes
No
No
Open
Open
Open
DHCP-Srv
Dect R4
Branch
Trunk
Ext to
Branch
Yes
Yes
Yes
Yes
Yes
No
?
Description
B5800 Configuration
Service – Secured. See optional 50804.
B5800 System Status
Access.
B5800 Security
Settings Access –
Secured. See optional
50812.
If configured, B5800 obtains its' IP address from a remote server.
File transfer Web client access.
Offering H.323 service to IP phones.
I-D
I-E
I-F
1719
5061
50796
TCP/
RAS
TCP/
TLS
UDP/
Partner
App
I-G 50804-C TCP/
HTTPS
B5800
Config
Access
I-H 50812-C TCP/
HTTP
No Open IP Phones No
Yes Closed Session
Yes Closed Phone Mgr Yes
No
No
Open
Open
Manager
B5800
Manager
B5800
Manager
Yes
Yes
Yes
Offering H.323 service to IP phones.
Encrypted SIP signaling.
Control of telephones from Phone Manager,
Soft Console.
B5800 Configuration
Service – Unsecured.
See 50805.
B5800 Security
Settings Access –
282 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Egress ports for B5800 Branch Gateway and SIP phones
# Dest.
Port
Network
/App
Protocol
En or
Dis
?
B5800
Sec
Settings
Access
Default
Port
State
Remote
Device
Ext to
Branch
?
Description
Unsecured. See
50813.
For a description of the column headings, see Table column heading definitions on
page 285.
Egress ports for B5800 Branch Gateway and SIP phones
1 53
2 69
3
4
5
6
# Dest.
Port
123
162
389
500
Network
/App
Protocol
UDP/
DNS
En or
Dis
?
Default
Port
State
Remote
Device
No Open DNS
Server
UDP/
TFTP
Ext to
Branch
Yes
No Open Manager Yes
?
Description
DNS service to resolve
URL and IP addresses.
B5800 Branch Gateway status, configuration data, program data.
on page 277 for ranges.
Yes UDP/
NTP
UDP/
SNMP
TCP/
LDAP
UDP/
IKE
No Open NTP
Server
Yes Closed Trap
Receiver
Yes
Yes
Closed
Closed
LDAP
Server
Security device
Yes
Yes
Yes
NTP (RFC4330)
Service.
Trap generation from
B5800 Branch
Gateway.
Import of directory information from LDAP database.
Form IPSec associations with remote security devices. Requires license.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 283
Avaya port matrix for B5800 Branch Gateway and SIP phones
7
# Dest.
Port
514
Network
/App
Protocol
UDP/
Syslog-
Cli
En or
Dis
?
Default
Port
State
Remote
Device
Yes Open Syslog
Server
8 5005-C RTCP
9 5060
10 49152 –
53247-C
TCP/SIP No Open
UDP/
RTP-
RTCP
Yes Open IP Phones,
RTCP
Collector
Yes
Yes
11 50794 UDP/
TCP/
Monitor
Yes Open NMS
No Open Manager
Ext to
Branch
Yes
?
Description
No, but could be
Log files transmitted from IP phones to server.
Yes RTCP collector (HP-
Openview, AIM, etc.).
SIP signaling.
Dynamically allocated ports used during VoIP calls for RTP and RTCP traffic. The port range can be adjusted through the System >
Gatekeeper tab.
Event, trace and diagnostic outputs.
OPTIONAL
E-1 25
E-2 37
E-3 67
E-4 1720
E-5 5061
TCP/
SMTP
UDP/
Time
UDP/
DHCP-
Srv
TCP/
H323
TCP/
TLS
Yes Open Mail Server Depend s
Yes Closed Manager Yes
Yes IP Clients No
TIME (RFC868)
Service supported by
Manager and VMPro.
Requested by B5800
Branch Gateway. This service is an option to
NTP – port 123.
DHCP service to IP phones, PCs and other clients.
No Yes Open H323
Server
Yes Closed Session
Manager
Yes
Offering H.323 service to IP phones.
Encrypted SIP signaling.
For a description of the column headings, see Table column heading definitions on
page 285.
284 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Egress ports for B5800 Branch Gateway and SIP phones
Table column heading definitions
Column heading
Dest Port
Network/App
Protocol
En or Dis?
Default Port
State
Description
Destination port — this is the layer-4 port number to which the connection request is sent. Valid values include 0 – 65535.
Network/application protocol — this is the name associated with the layer-4 protocol and layers-5-7 application.
Optionally Enabled or Disabled? — this field indicates whether customers can enable or disable a layer-4 port changing its default port setting. Valid values are Yes or No.
• No means the default port state cannot be changed (that is, enable or disabled).
• Yes means the default port state can be changed (that is, enabled or disabled).
Default Port State — a port is either open, closed, filtered or N/A.
• Open ports will respond to queries.
• Closed ports may or may not respond to queries and are only listed when they can be optionally enabled.
• Filtered ports can be open or closed. Filtered UDP ports will not respond to queries. Filtered TCP will respond to queries, but will not allow connectivity.
• N/A is used for the egress default port state since these are not listening ports on the product.
Remote Device Remote Device — this is the remote device that is initiating a connection request (Ingress Connections) or receiving a connection request (Egress
Connections).
Ext to Branch?
External to Branch? — this indicates whether traffic to this layer-4 port is needed between the branch and other sites, requiring this port to be open on firewalls, if any, between the branch and the rest of the customer’s network. Note that this depends on the customer’s deployment. Valid
Values are:
• Yes (meaning typically needed)
• No (meaning not expected to be needed)
• Depends (on customer deployment)
Notes:
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 285
Avaya port matrix for B5800 Branch Gateway and SIP phones
• Email will not flow through the B5800 Branch Gateway in this example. See optional section for port 25.
• An off-site DHCP server is used to supply IP addresses to phones and PCs. Otherwise, add ports 67 and 68 in optional sections.
• The B5800 Branch Gateway IP address will be manually configured and not need a DHCP server.
• TFTP service begins using port 69, but eventually uses the source ports from both sides.
• Ports 80804 and 80812 are unsecure communications but have optional port 80805 and
80813 as secure options.
• For B5800 Branch Gateway R6.1, the TFTP/UDP port selection is an issue; IP Office
Manager, ENM, and SysMonitor do not constrain the selection of TFTP/UDP source port.
B5800 Branch Gateway R6.2 improves this TFTP port issue greatly in a number of ways:
- System Manager does not use TFTP.
- SysMonitor and IP Office Manager have configurable TFTP/UDP port ranges.
• HTTPS is used for DECT R4 administration.
286 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Port usage diagram
Port usage diagram
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 287
Avaya port matrix for B5800 Branch Gateway and SIP phones
In this diagram, direction of the arrow depicts call initiation. Data traffic will typically be 2way.
288 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Appendix B: B5800 Branch Gateway call flows
Calls from local extensions (i.e. deployed in the distributed branch user model)
1. Local phone to local phone
Local phone A B5800 Branch Gateway local phone B
2. Local phone to PSTN (using local trunking)
Local phone B5800 Branch Gateway B5800 Branch Gateway trunk (e.g. FXO, ISDN, SP
SIP Trunk) PSTN
3. Local phone to PSTN (using centralized trunking)
Local phone B5800 Branch Gateway Session Manager central gateway/SBC PSTN
4. Local phone to headquarters or other enterprise site
Local phone B5800 Branch Gateway Session Manager target phone’s controller target phone
Calls to local extensions (i.e. deployed in distributed branch user model)
1. From PSTN to local extension via IP Office auto-attendant (branch auto-attendant LDN is associated with local B5800 Branch Gateway trunk)
PSTN B5800 Branch Gateway trunk (e.g. FXO, ISDN, SP SIP trunk) B5800 Branch
Gateway auto-attendant caller enters extension number local phone
2. From PSTN direct to Local phone’s DID (LDN is associated with local B5800 Branch Gateway trunk)
PSTN B5800 Branch Gateway trunk (e.g. FXO, ISDN, SP SIP trunk) B5800 Branch
Gateway local phone
3. From headquarters (or other enterprise site) to local phone’s enterprise number
Originating phone originating phone’s controller Session Manager B5800 Branch
Gateway local phone
4. From headquarters (or other enterprise site) to local extension via IP Office auto-attendant
Originating phone originating phone’s controller Session Manager B5800 Branch
Gateway B5800 Branch Gateway auto-attendant caller enters extension number local phone
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 289
B5800 Branch Gateway call flows
290 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Appendix C: Branch PSTN call routing examples
Each B5800 Branch Gateway system can support its own external PSTN trunks. When deployed in an
Avaya Aura
®
network, you have considerable flexibility over where outgoing PSTN calls should emerge from the network and similarly where incoming calls should be routed.
The following examples demonstrate some of the options available:
•
on page 291 — External calls at a branch site can be rerouted to be dialed out at another site. This can be done for reasons of call cost and call control. For example, the central site may have a bulk call tariff for national and international calls that would benefit all branches.
•
on page 294 — Having configured the branch to send outgoing external calls to the Avaya Aura ® Session Manager for onward routing, there may be cases where a specific number should still be routed via the branches own PSTN trunks.
•
on page 296 — The B5800 Branch Gateway can be configured to allow some calls that would normally use the Avaya Aura
®
Session Manager line to be routed via the PSTN when the Avaya Aura ® Session Manager line is not available.
The various methods used in these examples can be combined to match the customer's needs. However the main aim should be as follows:
• To keep the branch configuration as generic as possible, i.e. to use the same PSTN call control in all branch configurations. This simplifies maintenance of multiple branches.
• To centralize as much of the PSTN call control in the Avaya Aura ® Session Manager as possible.
Again this simplifies maintenance and control.
Centralized call control
External calls at a branch site can be rerouted to be dialed out at another site, typically the headquarters site. This can be done for reasons of call cost and control and to reduce the external PSTN capacity required at the individual branch sites.
For example, we can route all national and international calls to the headquarters site to benefit from a bulk cost reduction available for calls from that site. The Avaya Aura ® Session Manager there routes the calls out via PSTN services at that site. Note, however, that the Avaya Aura ®
Session Manager could alternately use the trunks at a branch for some calls. For example, if the national call is to an area code that is local to a particular branch, the call could be routed to that branch for dialing on its PSTN trunks.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 291
Branch PSTN call routing examples
Routing B5800 Branch Gateway calls — example
About this task
This example assumes that all the branches were initially setup with the default North American locale. For B5800 Branch Gateway that means that a dial 9 prefix is used for external calls.
For calls in other locales or between branches in different locals, the example would be adjusted to ensure that the resulting number received at the remote branch would be routed to an external PSTN trunk and is suitable for external dialing.
At each B5800 Branch Gateway, we need to ensure that calls starting with 90, the external and then international number prefixes, are routed to the branch's Avaya Aura
®
Session
Manager line rather than direct to an external PSTN line.
In the B5800 Branch Gateway system configuration, the default system short code 9N is used to match calls prefixed with a 9. The short code removes the 9 prefix and routes the call to the branch's ARS form 50: Main.
Procedure
1. Start Manager and connect to the B5800 Branch Gateway system.
2. In the left navigation pane, click ARS.
292 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Centralized call control
3. Click 50: Main.
Within the ARS window, the default 0N; short code that matches international numbers currently routes those calls to any available trunk in line group 0.
4. To edit the short code, click the short code.
5. Click the Edit... button.
6. Make the following changes: a.
In the Code field, leave this set to 0N;.
b.
In the Feature field, change this to Dial.
c.
In the Telephone Number field, change this to 90N.
The 9 has been added back as it matches the dial pattern typically used at the
Avaya Aura
®
site for matching a call that needs routing to the PSTN.
d.
In the Line Group ID field, change this to match the Avaya Aura
®
Session
Manager line Outgoing Group ID. The default is 99999.
7. Click OK.
8. Repeat Steps 4 through 7 for the 1N; short code which is used for national calls.
The branch system's default ARS form is now set to route all national and international calls to the Session Manager line and thus to the Avaya Aura
®
Session
Manager.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 293
Branch PSTN call routing examples
9. Click OK.
10. Select File > Save Configuration.
Branch PSTN override
In the example described in Centralized call control
on page 291, we configured the branch system so that all national and international calls go to the headquarters site for routing to the
PSTN. There may occasionally be scenarios where a particular number needs to override this and be dialed via the branch system's own PSTN trunks.
One example is the Avaya Aura Messaging or Modular Messaging PSTN number that can be configured for access to voicemail when the branch's Avaya Aura
®
Session Manager line is out of service. Another might be to provide a maintenance number to the headquarters site to report suspected loss of the Avaya Aura ® Session Manager line connection.
Adding an overriding short code
Procedure
1. From the System Manager console, select the B5800 Branch Gateway device and click Edit to edit the system configuration for the device. IP Office Manager will be launched on your PC. For more information, see
Editing a B5800 Branch Gateway system configuration from System Manager on page 159.
2. In the left navigation pane, click ARS.
294 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Branch PSTN override
3. Click 50: Main.
Within the ARS form, the default 1N; short code is the one used for national calls.
It would match the MM PSTN Number or AAM PSTN Number and attempt to route it to the SM Line which we know is out of service if the MM PSTN Number or AAM
PSTN Number is being used for calls to voicemail. We can change the routing by adding a specific short code for the MM PSTN Number or AAM PSTN Number.
4. To add a short code, click the Add... button.
5. Make the changes as follows: a.
In the Code field, set this to match the external PSTN number for Modular
Messaging or Avaya Aura Messaging without the external dialing prefix.
b.
In the Feature drop-down box, select Dial3K1.
c.
In the Telephone Number field, set this to N to match the whole number in the
Code field.
Note:
For a setup where the voicemail mail box numbers configured on Modular
Messaging or Avaya Aura Messaging are the same as the caller's DID, the short code to route the PSTN call should be configured so that the caller ID is withheld. To do this, enter a W in the Telephone Number field of the short code. This ensures that during rainy-day operation, the voicemail system does not automatically go to the voicemail mail box of the caller based on the caller ID.
d.
In the Line Group Id drop-down box, select the line group ID being used for the branch's PSTN trunks. The default is 0.
6. Click OK.
The ARS now has two short codes that will potentially match external national calls.
However, one is a more exact match for certain calls and therefore will be applied
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 295
Branch PSTN call routing examples to those calls.
7. Click OK.
8. Select File > Save Configuration.
PSTN trunk fallback
In branch scenarios where centralized call control and trunking (see Centralized call control
on page 291) has been configured for certain calls, loss of the Avaya Aura
®
Session Manager line connection will impact making those calls. For instance, in our example where all branch national and international calls are routed via the headquarters site, loss of the Avaya Aura ®
Session Manager line will leave the branch users only able to make local calls.
Since loss of the Avaya Aura
®
Session Manager line should only be an infrequent and temporary condition, some restriction during that state may be acceptable. However the following options can be used to allow continued branch operation:
• If the headquarters site has multiple Avaya Aura ® Session Managers for redundancy, each branch can also be configured with multiple Avaya Aura ® Session Manager lines. See
Avaya Aura Session Manager line redundancy on page 152 for more information.
• As in our example business, centralized call control has not been applied to all branch local calls. Therefore local calls are still available without any additional configuration for the loss of the Avaya Aura ® Session Manager line connection.
• Since loss of the Avaya Aura
®
Session Manager line should be infrequent and temporary, the loss of some services may be tolerable until the Avaya Aura ® Session Manager line issue is resolved. However, even if that is the case, it may be recommended to configure
296 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
PSTN trunk fallback a headquarters PSTN number that can be dialed to report the Avaya Aura
®
Session
Manager line issue. See Branch PSTN override
on page 294 for more information.
• Provide PSTN trunk fallback within the branch configuration. See Configuring PSTN trunk fallback
on page 297. Note however that PSTN fallback will also occur when the number of external calls exceeds the available SIP trunk licenses.
Note:
If you want to have long distance routing on local trunks, be sure that the appropriate trunks have been ordered from the local provider. Do not create a route for international phone calls if you do not have that service.
Configuring PSTN trunk fallback
About this task
Use this procedure to provide PSTN trunk fallback with the branch configuration.
Procedure
1. Start Manager and connect to the B5800 Branch Gateway system.
2. In the left navigation pane, click ARS.
3. Click the New icon and select ARS.
4. Enter a Route Name, for example PSTN.
5. To add a short code click the Add... button.
A short code is required that will send the national calls to the branch's own PSTN.
Enter the normal defaults for such a short code as follows:
6. Make the changes as follows: a.
In the Code field, enter 1N;. For this example, 1N; will match any national number dialing.
b.
In the Feature field, leave the entry set as Dial3K1.
c.
In the Telephone Number field, enter 1N. For this example 1N will match the number dialed by the user after the dial 9 prefix.
d.
In the Line Group Id drop-down box, select the line group used for the B5800
Branch Gateway system's external trunks. The default is 0.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 297
Branch PSTN call routing examples
7. Click OK.
8. Click OK.
9. Double click on the existing default ARS that was reconfigured to send all branch national and international calls to the Avaya Aura ® Session Manager line.
10. In the Additional Route drop-down box , select the PSTN ARS form just created above.
The form is now set such that, if the Avaya Aura ® Session Manager line is not available (out of service or all licensed channels busy) calls can be checked for a dialing match in the PSTN ARS form. This works as follows:
• The Alternate Route Priority Level controls which users are able to use the alternate route immediately, ie. those user's whose priority is equal or higher than this setting. The default priority for users is 5.
298 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
PSTN trunk fallback
• The Alternate Route Wait Time is used for caller's whose priority is not sufficient to use the alternate route immediately. The default setting is 30 seconds. However, you may want to adjust this setting to one that meets your requirements.
• Since the only short code match in the alternate route in our example is for national calls, international calls will continue to wait for the Avaya Aura
®
Session Manager line.
11. Select File > Save Configuration.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 299
Branch PSTN call routing examples
300 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Appendix D: Authorization codes
Authorization codes are not shown by default. IP Office Manager must be modified in order to support authorization codes. Each authorization code is associated with a particular user or user rights set. The user or users associated with the user rights can then dial numbers which are set to trigger forced authorization code entry. Once a code is entered, the short code settings of the user or user rights with which the code is associated are used to complete the call. This allows authorized users to make otherwise restricted calls from any extension without first having to log in to that extension and then log out after the call.
How authorization codes work
• A user dials a number that matches a short code set to Force Authorization Code.
• The user is prompted to enter an authorization code.
• They dial their authorization code. If a matching entry is found in Authorization Codes entries, the system checks the corresponding user or user rights (in that order). Note that the user or user rights checked does not necessarily need to be connected with the user dialing or the user whose extension is being used to make the call.
- The dial string is checked against the short codes with the matching user or user rights.
- If it matches a dial short code or no short code, the call is allowed. Otherwise, it is blocked. Note that the short code is not processed, it is just checked for a match.
- If multi-tier authorization codes are required, there must be blocking (busy) short codes (or a wild card '?' )
Example
A restaurant has a number of phones in publicly accessible areas and wants to control what calls can be made from these phones. They want these phones to allow anyone to make local calls, restrict restaurant staff to local and cell phone numbers (044...), and allow the manager to also be able to call long distance numbers (01...). The following table shows how this is configured.
ARS Table
In the Main (50) ARS table, the following short codes are added:
• 044XXXXXXXXXX / 044N / Dial / Force Auth Code
• 01XXXXXXXXXX / 01N / Dial / Force Auth Code
Authorization Codes
The following two authorization codes are configured:
• 2008 is associated with a set of User
Rights called Cell.
• 1983 is associate with a set of User Rights called LDandCell.
User Rights
Cell LCandCell
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 301
Authorization codes
ARS Table
• 044N / . / Dial
Allows calls to cell phone numbers.
• 01N / . / Busy
Blocks calls to long distance numbers.
• ? / . / Busy
Block any other calls that require an authorization code.
Authorization Codes
• 044N / . / Dial
Allows calls to cell phone numbers.
• 01N / . / Busy
Allows calls to long distance numbers.
• ? / . / Busy
Block any other calls that require an authorization code.
It is recommended to use short codes that use X characters to match the full number of characters to be dialed. That ensures that authorization code entry is not triggered until the full number has been dialed rather than mid-dialing. For example, 09 numbers are premium rate in the UK, so you would create a
09XXXXXXXXX / N / Dial short code set to Forced Authorization. In the associated user or user right short code, it is recommended to use 09N type short codes.
Warning:
Changing PC registry settings
Avaya accepts no liability for any issues arising from editing PC registry settings. If you are in any doubt about how to perform this process, you should not proceed. It is your responsibility to ensure that the registry is correctly backed up before any changes are made.
Enabling authorization codes in Manager
About this task
A change to the Manager PC registry settings is required to enable support for authorization codes within Manager. Once this change is made, various authorization code related features are visible when Manager is restarted.
Warning:
Changing PC registry settings
Avaya accepts no liability for any issues arising from editing PC registry settings. If you are in any doubt about how to perform this process, you should not proceed. It is your responsibility to ensure that the registry is correctly backed up before any changes are made.
Procedure
1. Close Manager.
2. Locate the registry key HKEY_CURRENT_USER\Software\Avaya
\IP400\Manager\EnableAuthorisationCodes and change its value from 0 to 1.
302 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Force authorization codes
3. Restart Manager and load a configuration.
Force authorization codes
There are two methods to force a user to enter an authorization code in order to complete dialing an external call.
• To Force Authorization Codes on All External Calls
A user can be required to enter an authorization code for all external calls. This is done by selecting Force Authorization Code (under User > Telephony > Supervisor
Settings).
• To Force Authorization Codes on Specific Calls
To require entry of an authorization code on a particular call or call type, the Force
Authorization Code option should be selected in the short code settings. This can be used in user, user rights, or system short codes in order to apply its effect to a user, group of users, or all users respectively. You need to ensure that the user cannot dial the same number by any other method that would by-pass the short code, for example with a different prefix.
About entering an authorization code
Where possible, when an authorization code is required, the user can enter it through their phone's display. However, this is not possible for all types of phones. For example, it is not possible with analog phones and Avaya XX01 or XX02 phones. The users of these devices must enter the authorization code by using a short code set to the Set Authorization Code feature immediately before making the call.
When entry of an authorization code is triggered, the user can enter any authorization code with which they are either directly associated or associated through their current user rights.
Note:
• If account code entry is setup for a particular number, calls forwarded or transferred to that number will also trigger account code entry.
• On systems using line appearances to BRI trunk channels to make outgoing calls, account code entry may not be triggered. This can be resolved by adding a short code such as [9]XN;/Dial/XN/0 (adjusting the prefix and line group as necessary).
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 303
Authorization codes
Authorization code configuration settings
• Authorization Code: The digits used for the authorization code can be up to 12 digits in length. Each code must be unique. Wild cards are not usable with authorization codes.
• User Rights: This field is used to select the user right with which the authorization code is associated. The authorization code can then be used to authorize calls made by users currently associated with that set of user rights.
• User: This field is used to select a user with which the authorization code is associated.
The authorization code can then be used to authorize calls made by that user.
304 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Appendix E: Recommended courses for
Avaya B5800 Branch Gateway training
This appendix lists recommended courses for B5800 Branch Gateway, Session Manager, System
Manager, and Communication Manager.
Recommended courses
Table 1: B5800 Branch Gateway
Type Code Course title
Existing 2U00021O Avaya Branch Gateway —
What Sales needs to know for the first conversation
Delivery Duration
(hours) eLearning 0.5
First offering
Available now
Available now
Existing 2U00022O Avaya Branch Gateway —
What Sales needs to know to continue the conversation eLearning 0.5
Existing 4U00112V PA Implement: Avaya B5800
Branch Gateway
Implementation vILT 16 Available now
1 Available now
Existing 4U00112A PA Implement: Avaya B5800
Branch Gateway
Implementation Assessment
New
Online
Assessme nt
5U00005V ACSS — Avaya B5800
Branch Gateway–
Implementation,
Administration, Maintenance, and Troubleshooting vILT
New TBD ACSS — Avaya B5800
Branch Gateway–
Implementation,
Administration, Maintenance, and Troubleshooting Exam
ACSS
Proctored
Exam
40
2
May
2012
May
2012
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 305
Recommended courses for Avaya B5800 Branch Gateway training
Table 2: Avaya Aura
®
Session Manager and System Manager
Type
New
New
New
New
New
New
New
Code Course title
5U00106W Avaya Aura
®
System
Manager Overview
5U00105W Avaya Aura
®
Session
Manager Overview
5U00095V Avaya Aura
®
System
Manager Implementation,
Administration, Maintenance and Troubleshooting
5U00096V Avaya Aura
®
Session
Manager Implementation,
Administration, Maintenance and Troubleshooting
Delivery Duration
(hours)
WBT course
WBT course vILT vILT
5U00097I Avaya Aura
®
Session Manger and System Manager
Implementation,
Administration, Maintenance and Troubleshooting
5U00104W Avaya Aura
®
Session
Manager 6.2 Delta Overview
5U00103W Avaya Aura
®
System
Manager 6.2 Delta Overview
ILT
WBT course
WBT course
1
4.5
16
64
80
1
1
First offering
Available now
Available now
April
2012
April
2012
April
2012
Available now
Available now
Table 3: Avaya Aura
®
Communication Manager and CM Messaging – Embedded
Type Code Course title Delivery Duration
(hours)
ILT 40 New
Existing
5U00041I Avaya Aura
®
Communication
Manager Administration
3100 Avaya Aura
®
Communication
Manager Administration
Exam
Existing 5U00040I Avaya Aura
®
Communication
Manager Maintenance and
Troubleshooting
Existing 5M00050I/V Avaya Aura
®
Communication
Manager Messaging
Embedded Administration,
Maintenance and
Troubleshooting
ACSS
Proctored
Exam
ILT vILT/ILT
1
40
40
First offering
Available
Now
Available
Now
Available
Now
Available
Now
306 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Recommended courses
Type Code Course title
Existing 3101
Update ATI02348IE
N/VEN
Avaya Aura
®
Communication
Manager and CM Messaging
- Embedded Maintenance and Troubleshooting Exam
Avaya Aura
®
Communication
Manager Implementation
Existing
New
ATI01731V
EN
Avaya Aura
®
Communication
Manager Messaging
Embedded Implementation
4U00115I/V Avaya Aura
®
Communication
Manager Implementation
Upgrade (R5.X to R6.X)
Existing
New
6002 Avaya Aura
®
Communication
Manager and CM Messaging
(R6.X) Implementation Exam
4U00121W Avaya Aura
®
Communication
Manager 6.2 Technical Delta
Delivery Duration
(hours)
ACSS
Proctored
Exam vILT/ILT vILT vILT/ILT
ACIS
Proctored
Exam
WBT course
1.75
40
16
16
2
2
First offering
Available
Now
March
2012
Available
Now
March
2012
Available
Now
Available
Now
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 307
Recommended courses for Avaya B5800 Branch Gateway training
308 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Appendix F: T7000 and M7000 Series Digital
Deskphones
The Business Series Terminals (BST) T7000 and M7000 Series Digital Deskphones offer a feature-rich portfolio with enhanced capabilities that provide telephony solutions for a broad landscape of users, from high-volume call positions and executives to low-intensive users and small workgroups.
The T7000 and M7000 Series Digital Deskphones were originally positioned for deployment on two system platforms from the Nortel Heritage, Norstar and BCM, providing both investment protection and a migration path between either system. The T7000 and M7000 Series Digital Deskphones offer full integration with
Norstar and BCM features, as well as integration with basic and advanced applications such as
Messaging, Intelligent Contact Center, Computer Telephony Integration (CTI) and integrated voice and data solutions.
The T7000 and M7000 Series Digital Deskphones are now available on B5800 Branch Gateway and offer customers another migration option from Norstar or BCM to B5800 Branch Gateway.
The T7000 and M7000 Series Digital Deskphones offer:
• Tilt display – provides clearer viewing of information or message prompts on the LCD in different lighting environments.
• Message waiting indication/Visual ringing lamp – alerts the user of incoming messages or that their phone is ringing when they are on another call.
• Headset interface – is driven from the Digital Terminal Interface Chip (DTIC). Volume control for the headset is also provided. Operation of the headset is mutually exclusive, with handsfree operation.
When a headset is connected, all operations normally associated with handsfree operation affect the headset. This includes on-hook dialing and volume control while active and muting.
• Handsfree interface – is programmed through the administration function and is supported by a microphone and loudspeaker.
• External ringer interface – receives alerting signals that are routed to the external ringer jack as well as to the speaker in the telephone. This alerting signal can be amplified and connected to external speakers to provide an auxiliary ringer function for the telephone. The external speaker is connected with a two-wire modular telephone cord to pins 3 and 4 of the external ringer jack.
Note:
The T7000 and M7000 Series Digital Deskphones do not work on all digital ports of B5800 Branch
Gateway but require a specific 8-port expansion card or 16/30 port expansion module. See
System components on page 20 for more information. The T7000 and M7000 Series Digital Deskphones
supported on B5800 Branch Gateway are primarily intended for migration from Norstar to BCM.
Although T7000 and M7000 Series Digital Deskphones can be used for new installations, Avaya recommends using the 1400 Series or 9500 Series Digital Deskphones in order to have access to all
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 309
T7000 and M7000 Series Digital Deskphones
B5800 Branch Gateway advanced features such as Visual Voice, feature menus, and self labeling keys
(9500 telephones only).
Features available on the T7000 and M7000 Series Digital
Deskphones
On the B5800 Branch Gateway the following features are available on the T7000 and M7000
Series Digital Deskphones using the feature key and the Feature Access Codes inherited from
Norstar and BCM. Other B5800 Branch Gateway features are also available by dialing the
B5800 Branch Gateway Feature Access Codes.
F0
F2
F3
F4
F5
F60
F65
F66
F69
F70
F74
F*0
Feature Access
Codes
F*1
F*2
F*3
F*4
F*6
F*7
F*80
F*82
Description
Button query (also allows DN query via I/C button)
Self-admin auto dial button
Self-admin auto dss button
Self-admin auto feature button
Self-admin program user speed dial
Self-admin ring type
Self-admin contrast
Self-admin ring volume
Dial mode selection (Enbloc/Pre-dial [editable], or Standard/
Overlap dial)
Speed dial
Ring Again, F#2 cancel
Conference
Call Forward, F#4 cancel
Last Number Redial
Page (no F61-F63)
Retrieve Messages - Enters Voicemail System on IP Office (Basic
Embedded Voicemail)
Dial Voice Call
Dial Priority Call
Transfer
Call Park, F#74 Retrieve
310 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Features available on the T7000 and M7000 Series Digital Deskphones
Feature Access
Codes
F75
F76
F77
F85
F802
F803
F812
F981
Description
Call Pickup Group
Call Pickup Extn
Call Timer
Do Not Disturb, F#85 cancel
Group Listen, F#802 cancel
Show Time
Call Log
Enter Voice Mail System (same as F65) AUDIO ONLY
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 311
T7000 and M7000 Series Digital Deskphones
312 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Appendix G: 1100 Series and 1200 Series IP
Deskphones
The 1100 Series and 1200 Series SIP 4.3 deskphones are supported on B5800 Branch Gateway using the SIP protocol. When used with BCM systems, the phones use the UNIStim protocol. Because of the different protocols, the user interface can be slightly different when the phones are used with B5800
Branch Gateway.
The following features are supported on B5800 Branch Gateway:
• Standard phone features like hold, transfer, conference
• Multiple call appearances (bridged appearances and trunk-line appearances are not supported)
• Message waiting support
• Busy lamp keys with speed-dial, status indication, and pickup of ringing calls
• Application support — the telephones can be used in combination with applications.
• Self labeling Feature keys — allows access to selected B5800 Branch Gateway features using a single key-press. If additional parameters are needed, the user is guided using a dialog interface of feature request plus softkeys.
• Feature key — The supported features are also available pressing a feature key (or soft key) plus the appropriate feature code. The feature codes are identical to the features codes from BCM, therefore making transition easy.
• Ease of installation — the telephones can be managed from IP Office Manager and are easily installed. B5800 Branch Gateway serves as DHCP server and can provide configuration files, software updates, etc. To install the telephones, only IP Office Manager is required.
• Easy migration from BCM to B5800 Branch Gateway — when migrating telephones from BCM to
B5800 Branch Gateway, when B5800 Branch Gateway DHCP server is used, the system installs and upgrades the telephones to the correct software for B5800 Branch Gateway. This makes migration easy and quick.
The SIP 4.3 firmware provides the following enhancements:
• Pressing the Send key in order for the phone to start dialing is no longer required (1-10 sec timeout, default = 5 sec).
• Language selection via IP Office Manager is supported.
For more information about the 1100 Series and 1200 Series SIP phones, see:
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 313
1100 Series and 1200 Series IP Deskphones
• SIP Software for Avaya 1100 Series IP Deskphones–Administration , document number NN43170–
600
• SIP Software for Avaya 1200 Series IP Deskphones–Administration , document number NN43170–
601
Features available on the 1100 Series and 1200 Series SIP
4.3 phones
On the B5800 Branch Gateway, the following features are available on the 1100 Series and
1200 Series SIP 4.3 phones. The features are accessible through the feature key that can be administered to a button on the phone or by dialing the Feature Access Codes for the desired feature.
Feature
F*0 – Button query (also allows DN query via I/C button)
Supported
Details
F*1, F*2, F*3 – Self-admin button programming
Supported
F*6 – Self-admin ring type Function supported on the phone but not using the Feature
Access Code
F*7 – Self-admin contrast Function supported on the phone but not using the Feature
Access Code
F*80 – Self-admin ring volume
Function supported on the phone but not using the Feature
Access Code
F0 – Speed dial
F3 – Conference
F4 – Call Forward, F#4 cancel
F5 – Last Number Redial
Supported
Supported
Supported
F60 – Page (no F61-F63)
F66 – Dial Voice Call
F70 – Transfer
F74 – Call Park, F#74
Retrieve
F75 – Call Pickup Group
Supported
Supported
Supported
Function supported on the phone but not using the Feature
Access Code
Supported
Supported
314 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Features available on the 1100 Series and 1200 Series SIP 4.3 phones
Feature
F76 – Call Pickup Extn
F85 – Do Not Disturb, F#85 cancel
F981 – Enter Voice Mail
System (same as F65)
AUDIO ONLY
F812 – Call Log
Supported
Supported
Supported
Account Code Entry
After Call Work
Automatic Callback
Automatic Intercom – Dial voice call
Call Record
Cancel All Forwarding
Directed Call Pickup
Extension Login
Extension Logout
Follow Me Here
Follow Me Cancel
Follow Me To
Forward Number
Forward Busy Number
Forward On Busy
Forward On No Answer
Forward Unconditional
Private Call
Relay On
Relay Pulse
Set HG:
• Night Service
• Out of Service
• NS Group
• OOS Group
Supported
Supported
Supported
Supported
Supported
Supported
Supported
Supported
Supported
Details
Function supported on the phone but not using the Feature
Access Code
Supported
Supported
Supported
Supported
Twinning
Voicemail On
Supported
Supported
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 315
1100 Series and 1200 Series IP Deskphones
316 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
BCM
BEM
Centralized management
Centralized trunking
Distributed
Branch user model
Distributed trunking
Local extension
Local management
Mixed mode trunking
Glossary
Business Communications Manager; a system that includes hardware and software to provide private network and telephony management capability to small and meduim-sized businesses.
Business Element Manager; the primary management application for managing Business Communications Systems. It encompasses telephony programming, backup management, software update management, and log management.
This term is used to describe a central management system that delivers a set of shared management services and provides a single access interface to administer multiple branch locations and multiple distributed
B5800 Branch Gateway users.
This term describes routing outgoing external calls from the branch sites to the central site in order to utilize the central sites PSTN trunks. The same applies for distributing incoming PSTN calls from the central site to the appropriate branches.
This term describes a B5800 Branch Gateway deployment model where call processing for the branch phones is provided locally. Non-IP phones are connected to B5800 Branch Gateway and IP and certain SIP endpoints (not including the Avaya 9600 SIP phones) can be administered with B5800 Branch Gateway as their controller. Access to and from the rest of the Avaya Aura
®
network is via the B5800 Branch
Gateway system's Avaya Aura ® Session Manager link across the enterprise WAN. This connection allows for VoIP connectivity to other
B5800 Branch Gateway systems, to centralized trunking and to centralized applications such as conferencing and Modular Messaging.
This term describes the scenario where each branch retains and uses its own PSTN trunks for incoming and outgoing external calls.
See Native extension.
This term is used to describe managing a B5800 Branch Gateway device using the local IP Office Manager application.
The flexibility of Avaya Aura
®
Session Manager is such that both centralized and distributed trunking can be used. For example, routing all national and international calls via centralized trunking at the headquarters site while still allowing local calls via the branch sites.
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 317
Native extension
Native extension
NCM
NRS
Rainy day
SRG
Sunny day
Tail-End-Hop-Off
UCM
This term is used to describe extensions that get their call services from the branch site and operate in the Distributed Branch user model. A native extension is also referred to as a local extension.
Network Configuration Manager; a server-based management application that provides configuration management tools to manage a network of Business Communications Manager devices. These tools support tasks such as bulk distribution of selected configuration information, network-wide inventory management, and network-wide backup management.
Network Routing Service; provides SIP interoperability between Avaya
Communication Server 1000 and the B5800 Branch Gateway.
This term refers to a loss of network connectivity from the branch to the core data center.
Survivable Remote Gateway; extends the desktop feature and user interface of the Avaya Communication Server 1000 to remote IP branch office users and gives them full access to the same applications as the main site.
This term refers to full network connectivity from the branch to the core data center.
Part of mixed mode trunking, this describes scenarios where certain calls at other branches or the headquarters site are routed to the PSTN of another branch.
Unified Communications Management; web administration tool used to manage Avaya Communication Server 1000 systems.
318 Implementing B5800 Branch Gateway for a CS 1000 Configuration
Comments? [email protected]
October 2012
Index
Numerics
Bulk importing of devices ..........................................
1100 Series and 1200 Series SIP 4.3 phones ..........
C
A
About adding B5800 Branch Gateways to System
Manager ......................................................
About preserving staged button programming for BST
phones ...........................................................
About the xml file containing the B5800 Branch Gateway
devices ........................................................
About upgrading B5800 Branch Gateway software . . .
activating license entitlements ..................................
Activating license files ...............................................
activation process .....................................................
Adding distributed users to System Manager ...........
Adding System Manager as a certificate authority . . .
additional system procedures ...................................
Administering users ..................................................
187 centralized users ................................................
187 distributed users .................................................
Alternate Route Priority Level ...................................
Alternate Route Wait Time ........................................
Analog ........................................................................
77 phone barrier boxes .............................................
ARS ..........................................................................
Audio ..........................................................................
46 codec conversion .................................................
Authorization code configuration settings .................
Authorization codes ..................................................
Automatic codec preference settings .......................
Avaya Mentor videos ..................................................
B
B5800 Branch Gateway administration tools ............
201 using SAL to access ...........................................
B5800 Branch Gateway licenses ...............................
B5800 upgrades .........................................................
Barrier boxes ........................................................
analog phone .......................................................
rack mounting ......................................................
Batteries ...................................................................
Lithium ................................................................
branch and extension numbering .............................
Cable ..........................................................................
50 access requirements ............................................
50 clearance requirements .......................................
Cables ........................................................................
Maximum cable distances ....................................
Standard IP Office ................................................
Cabling .......................................................................
74 lightening protection .............................................
Call flows ..................................................................
Castle Rock ..............................................................
Centralized call control .............................................
change history ............................................................
Channels ....................................................................
compression .........................................................
Clock .........................................................................
Compression channels ...............................................
Configuration .......................................................
create new ...........................................................
erase ..................................................................
configuration checklist ..............................................
Configuring a short code to preserve user extension
configuration ..................................................
Configuring Avaya Aura Messaging .........................
Configuring CallPilot .................................................
Configuring CallPilot and CS 1000 to send MWI in a SIP
NOTIFY message to the user ......................
configuring Embedded Voicemail .............................
configuring Standalone Voice Mail ...........................
configuring the B5800 Branch Gateway for certificates
......................................................................
configuring user PLDS access ...................................
Connecting the control unit to the network .................
Connections ..........................................................
grounding .............................................................
out of building .......................................................
Control unit .................................................................
Rack mounting .....................................................
46 wall mounting .......................................................
Country .......................................................................
27 languages ............................................................
27 supported locales .................................................
Create configuration file .............................................
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 319
creating a backup of the system configuration using
System Manager .........................................
Creating a software library ........................................
creating a system template .......................................
creating a user template ...........................................
CS 1000 and B5800 Branch Gateway deployments . .
CS 1000 configuration considerations ........................
D
Default codec selection ............................................
Deliver activated license files to the branches ..........
Dial pattern ...............................................................
Disabling the System Manager administration feature for
a branch .......................................................
discovering branches in the network and adding them to
System Manager .........................................
distributed branch with Session Manager .............
Domain .....................................................................
DS ..............................................................................
IROB ....................................................................
76 phone ...................................................................
DTE port ...................................................................
Cable requirement ..............................................
RS232 ................................................................
232 settings ...............................................................
swapping ............................................................
external server ............................................................
F
Fallback ....................................................................
FCC Rules ................................................................
Features available on the 1100 Series and 1200 Series
SIP 4.3 phones ............................................
Features available on the T7000 and M7000 sets . . .
firewall policies .........................................................
firewall types .............................................................
Force authorization codes ........................................
FQDN .......................................................................
G
General information ....................................................
training courses ....................................................
generating a certificate on System Manager ............
Getting inventory ........................................................
ggeneral information ...................................................
Web sites .............................................................
Grounding control units ..............................................
H
E
Hazard Symbols .......................................................
Homologation Statement ..........................................
Hop-Off ...............................................................
how ports are used ...................................................
HP OpenView ...........................................................
editing a B5800 Branch Gateway from System Manager
......................................................................
editing the B5800 Branch Gateway Endpoint profile for a
user ..............................................................
egress ports for B5800 Branch Gateway and SIP phones
......................................................................
EMC Cautions ..........................................................
Canadian Department of Communications ........
EMC Caution for China ......................................
Federal Communications Commission ..............
Enabling authorization codes in Manager ................
Enabling branch SIP extension support ...................
Enabling WebLM licensing for the branch ................
Entity link ..................................................................
Envirmental requirements ..........................................
Example of So8 BRI module configuration ...............
Exporting the CS 1000 security certificate ................
Exporting the System Manager certificate ................
EXT O/P Port ............................................................
Extension numbers ...........................................
, 215 changing .............................................................
Renumbering ......................................................
I ingress ports for B5800 Branch Gateway and SIP
phones .........................................................
initial branch configuration ........................................
Initial Installation Utility .............................................
Initial Installation Utility, features automatically
configured ....................................................
installation ..................................................................
Installation .................................
,
,
81 admin applications ...............................................
card ......................................................................
grounding .............................................................
installer PC connection ........................................
rack mounting ......................................................
tools .....................................................................
unpacking .............................................................
320 Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012
wall mounting .......................................................
installation checklist ....................................................
installing a service pack .............................................
Installing IP Office Manager Lite from the System
Manager server to a PC ...............................
installing the license file on the System Manager WebLM
server ...........................................................
IP Address ................................................................
IP Office Operation in ...............................................
USA ....................................................................
L
O
Operation in .......................................................
Australia .............................................................
Canada ...............................................................
China ..................................................................
European Union .................................................
New Zealand ......................................................
Other DCP short codes ..............................................
Out of building ............................................................
74 connections ..........................................................
outgoing call routing .................................................
legal notices .................................................................
license entitlements ...........................................
activating ............................................................
searching for ......................................................
license modes ............................................................
Licensing ....................................................................
Lightening Portection ................................................
Lightening protection ..................................................
Link Monitoring .........................................................
Lithium Batteries .......................................................
Location, adding .......................................................
M
management ..............................................................
Manager .............................................
–
,
clock quality ........................................................
extension numbers .............................................
prefix dialing .......................................................
trunk clock quality setting ...................................
trunks .................................................................
upgrade software ...............................................
Managing B5800 Branch Gateways from System
Manager ......................................................
manually adding B5800 Branch Gateways to System
Manager ......................................................
Maximum SIP sessions ............................................
Module ......................................................................
Polycom video ....................................................
Modules ....................................................................
Trunk Interface ...................................................
Monitoring .................................................................
N
network assessment for VoIP requirements ...............
New configuration .......................................................
P
Pattern ......................................................................
Performing a certificate exchange between CS 1000 and
Session Manager .........................................
Planning .....................................................................
PLDS .................................................................
about ..................................................................
Policy ........................................................................
Polycom video module .............................................
Port .............................................
,
,
door ....................................................................
EXT O/P .............................................................
RS323 DTE ........................................................
Safety Classification ...........................................
port matrix for B5800 Branch Gateway and SIP phones
......................................................................
277 port type ranges ........................................................
port usage diagram ...................................................
Power Supplies ..........................................................
Uninterrupted Power Supply ................................
prerequisites ...............................................................
Prerequisites ..............................................................
Protocol ....................................................................
PSTN trunk fallback ..................................................
PSTN trunk fallback, configuring ..............................
PSTN trunking configurations .....................................
R
R6.2 service pack installation checklist ......................
Rack mounting control units .......................................
Recommended courses ............................................
Redundancy .............................................................
regenerate license files .............................................
199 regenerating a license file .........................................
registering .................................................................
rehosting ...................................................................
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 321
related documents ......................................................
related resources ........................................................
Avaya Mentor videos ...........................................
remote software library .........................................
remote software library for B5800 upgrades ..............
Remotely forcing a BST phone to return to default
settings ..........................................................
Renumber extensions ...............................................
Requirements .......................................................
Cable access .......................................................
Cable clearance ...................................................
Enviromental ........................................................
space ...................................................................
Wall mounting ......................................................
reset button ...............................................................
restoring the system configuration using System
Manager ......................................................
Restrictions when editing a B5800 Branch Gateway
system configuration from System Manager
Routing B5800 Branch Gateway calls ......................
Routing policy ...........................................................
S
revision history ...........................................................
Safety instructions ....................................................
Safety statements .....................................................
SAL ...................................................................
alarming .............................................................
203 registration .........................................................
registration request form ....................................
standalone gateway ....................................
searching for license entitlements ............................
sending the system template to multiple B5800 Branch
Gateways .....................................................
Session Manager tab field descriptions ....................
Setting B5800 Branch Gateway SNMP attributes ......
setting up external server ...........................................
Setting up System Manager to launch IP Office Manager
......................................................................
setting up the external server as remote software library
.......................................................................
Short Code tab field descriptions ..............................
SIP domain ...............................................................
SIP entity ..................................................................
SIP Link Monitoring ..................................................
SIP Registrar tab field descriptions ..........................
SIP trunk support ......................................................
SM line redundancy ..................................................
SNMP ..........................................
,
,
enabling ......................................................
installation ..........................................................
port ..............................................................
respond .......................................................
trap sending .......................................................
So8 ....................................................................
example ISDN terminal ......................................
Example video conference .................................
sockets .....................................................................
Software ...................................................................
237 erasecore software .............................................
Software applications .................................................
Space requirements ...................................................
Statement .................................................................
Homologation .....................................................
Safety .................................................................
Supported ...................................................................
27 language ..............................................................
27 locales ..................................................................
supported telephones .................................................
Synchronizing B5800 Branch Gateway with System
Manager ......................................................
System components ...................................................
System Manager administration feature, disabling from
IP Office Manager ........................................
System Manager administration feature, disabling using
System Manager .........................................
system requirements ..................................................
96 system requirements for the external server ..............
System shutdown using Manager ............................
System tab field descriptions ....................................
T
T7000 and M7000 Series Digital Deskphones .........
Tail-End-Hop-Off .................................................
TFTP port usage .......................................................
Time range, adding ...................................................
Training .....................................................................
Training courses .........................................................
Trunk fallback ...........................................................
Trunk Interface Modules ...........................................
Trusted ......................................................................
Type ..........................................................................
types of activation process .......................................
U
Unified Communications Management and System
Manager integration ......................................
upgrading the B5800 Branch Gateway device .........
Uploading an auto attendant audio file ..............
using Embedded File Management to install a PLDS
license ..........................................................
322 Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012
VoIP tab field descriptions ........................................
V
videos .........................................................................
Avaya Mentor .......................................................
Voice compression channels ......................................
Voicemail considerations ............................................
Voicemail operation ..................................................
Voicemail options ......................................................
Voicemail support options ..........................................
W
Wall mounting control units ........................................
Wall mountingrequirements ........................................
WAN .........................................................................
241 link ......................................................................
Web sites ....................................................................
Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 323
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement