Fujitsu LifeBook computer User guide

Copyright
Fujitsu Limited has made every effort to ensure the accuracy and completeness of this document. However, as
ongoing development efforts are continually improving the capabilities of our products, we cannot guarantee the
accuracy of the contents of this document. We disclaim liability for errors, omissions, or future changes.
LifeBook is a trademark of Fujitsu Limited.
Microsoft, Windows, MS, MS-DOS, and Windows NT are registered trademarks of the Microsoft Corporation of the
United States in the United States and other countries.
Intel is a registered trademark of the Intel Corporation of the United States.
Celeron is a trademark of the Intel Corporation of the United States.
ATI is registered trademark of ATI Techbologies INC.
Macrovision :This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this
copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and
other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or
disassembly is prohibited. Apparatus Claims of U.S. Patent Nos. 4,631,603, 4,577,216, 4,819,098 and 4,907,093
licensed for limited viewing uses only.
Dolby :Manufactured under license from Dolby Laboratories. "DOLBY", "PRO LOGIC," and the double-D symbol are
trademarks of Dolby Laboratories. Copyrights 1992-1999 Dolby Laboratories, All rights reserved.
Phoenix is a registered trademark of Phoenix Technologies Corporation of the United States.
K56flex is a trademark of Rockwell International Corporation and Lucent Technologies Corporation.
Other product names are trademarks or registered trademarks of their respective companies.
Other products are copyrighted by their companies.
Copyright© 1981-2001 Microsoft Corporation, All rights reserved.
Copyright© 2001 Phoenix Technologies, Ltd., All rights reserved.
All other products are trademarks or registered trademarks of their respective companies.
Explanations of the adjustments for the track pad cursor control are taken in part from the ALPS GlidePoint Driver
User’s Guide, copyright by LCS/Telegraphics in 1996.
© Copyright 2001 Fujitsu Limited. All rights reserved. No part of this publication may be copied, reproduced, or
translated, without the prior written consent of Fujitsu Limited. No part of this publication may be stored or transmitted in any electronic form without the written consent of Fujitsu Limited.
DECLARATION OF CONFORMITY
according to FCC Part 15
This device complies with Part 15 of the FCC Rules. Operations are subject to the following two conditions:
(1) This device may not be allowed to cause harmful interference, (2) This device must accept any interference
received, including interference that may cause undesired operation.
Wesbite: www.fujitsu-pc-asia.com
IMPORTANT SAFETY INSTRUCTIONS
1.
Read these instructions carefully. Save these instructions for future reference.
2.
Follow all warnings and instructions marked on the product.
3.
Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners.
Use a damp cloth for cleaning.
4.
Do not use this product near water.
5.
Do not place this product on an unstable cart, stand, or table. The product may fall, causing serious
damage to the product.
6.
Slots and openings in the cabinet and the back or bottom are provided for ventilation; to ensure reliable
operation of the product and to protect it from overheating, these openings must not be blocked or
covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other
similar surface. This product should never be placed near or over a radiator or heat register, or in a
built-in installation unless proper ventilation is provided.
7.
This product should be operated from the type of power indicated on the marking label. If you are not
sure of the type of power available, consult your dealer or local power company.
8.
This product is equipped with a 3-wire grounding-type plug, a plug having a third (grounding) pin. This
will only plug into a grounding-type power outlet. This is a safety feature. If you are unable to insert the
plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the purpose
of the grounding-type plug.
9.
Do not allow anything to rest on the power cord. Do not locate this product where persons will walk on
the cord.
10. If an extension cord is used with this product, make sure that the total ampere rating of the equipment
plugged into the extension cord does not exceed the extension cord ampere rating. Also, make sure
that the total rating of all products plugged into the wall outlet does not exceed 15 amperes.
11. Never push objects of any kind into this product through cabinet slots as they may touch dangerous
voltage points that could result in a fire or electric shock. Never spill liquid of any kind on the product.
12. Do not attempt to service this product yourself, as opening or removing covers may expose you to
dangerous voltage points or other risks. Refer all servicing to qualified service personnel.
13. Unplug this product from the wall outlet and refer servicing to qualified service personnel under the
following conditions:
a. When the power cord or plug is damaged or frayed.
b. If liquid has been spilled into the product.
c. If the product has been exposed to rain or water.
d. If the product does not operate normally when the operating instructions are followed. Adjust
only those controls that are covered by the operating instructions since improper adjustment
of other controls may result in damage and will often require extensive work by a qualified
technician to restore the product to normal condition.
e. If the product has been dropped or the cabinet has been damaged.
f. If the product exhibits a distinct change in performance, indicating a need for service.
14. CAUTION. When replacing the battery, be sure to install it with the polarities in the correct
position. There is a danger of explosion if the battery is replaced with an incorrect type or is
mistreated. Do not recharge, disassemble or dispose of in fire. Replace only with the same or
equivalent type recommeded by the manufacturer. Dispose of the used battery according to
the manufacturer’s instructions.
15. Use only the proper type of power supply cord set (provided in your accessories box) for this unit. It
should be a detachable type: UL listed/CSA certified, BS1363,ASTA,SS145 certified, rated 10A 250V
minimum, VDE approved or its equivalent. Maximum length is 15 feet (4.6 meters).
AUSTRALIAN WARNINGS
WARNING
FOR SAFETY REASONS, ONLY CONNECT EQUIPMENT WITH A TELECOMMUNICATIONS
COMPLIANCE LABEL. THIS INCLUDES CUSTOMER EQUIPMENT PREVIOUSLY LABELLED
PERMITTED OR CERTIFIED.
Connection of Non Certified/Approved peripherals may result in the equipment operating
outside the Australian EMI Standards.
Modems connected to the Australian telecommunications network must be operated in accordance with
the Labelling Notice. This modem has been specifically configured to ensure compliance with the ACA
Standards. Do not adjust your modem or software outside the values indicated below. To do so would
result in your modem being operated in a non-compliant manner.
Call Attempts/Retries:
Applications software shall be configured so that no more than 3 attempts are made to establish a connection
to a given number (Note: if the modem can detect service tones, up to 10 attempts can be made). If the call
sequence is unsuccessful, there shall be a delay of at least 30 minutes before attempting to call the
number again.
Failure to set the modem, and any application software used with the modem, to the values shown above
will result in the modem being operated in a non-compliant manner. Consequently, this would be in violation
of the Labelling Notice for this equipment, and the Telecommunications Act 1997 prescribes penalties for
the connection of non-compliant equipment.
NEW ZEALAND WARNINGS
The grant of a Telepermit for any item of terminal equipment indicates only that Telecom has accepted
that the item complies with minimum conditions for connection to its network. It indicates no
endorsement of the product by Telecom, nor does it provide any sort of warranty. Above all, it provides
no assurance that any item will work correctly in all respects with another item of Telepermitted
equipment of a different make or model, nor does it imply that any product is compatible with all of
Telecom’s network services.
This equipment is not capable under all operating conditions of correct operation at the higher speeds
for which it is designed. 56 KBPS connections are likely to be restricted to lower bit rates when connected
to some PSTN implementations. Telecom will accept no responsibility should difficulties arise in such
circumstances.
Immediately disconnect this equipment should it become physically damaged, and arrange for its
disposal or repair.
This equipment shall not be used in any manner, which could constitute a nuisance to other Telecom
customers.
This equipment shall not be set to make automatic calls to the Telecom “111” Emergency Service.
This device is equipped with pulse dialling while the New Zealand standard is DTMF tone dialling.
There is no guarantee that Telecom lines will always continue to support pulse dialling. It is strongly
recommended that pulse dialling is not used.
Some parameters required for compliance with Telecom’s Telepermit requirements are dependent
on the equipment (PC) associated with this device. The associated equipment shall be set to operate
within the following limits for compliance with Telecom’s Specifications:
For repeat calls to the same number.
There shall be no more than 10 call attempts to the same number within any 30 minute period
for any single manual call initiation, and
The equipment shall go on-hook for a period of not less than 30 seconds between the end of
one attempt and the beginning of the next attempt.
For Automatic calls to different numbers.
The equipment shall go on-hook for a period of not less than 5 seconds between the end of
one attempt and the beginning of the next attempt.
For Automatically answered Incoming Calls
Incoming calls shall be answered between 3 and 30 seconds from the start of the ringing.
For correct operation, the total of the RNs of all devices connected to a single line at anytime should
not exceed 5. The RN of this Equipment is 0.5.
WARNING
Connection of Non Certified/Approved peripherals may result in the equipment operating
outside the New Zealand EMI Standards.
Note: Modem setting in Windows 98 / Windows Me
The default modem setting in Windows 98 / Windows Me operating system is United States of
America. If you are residing in Australia or New Zealand, please choose the appropriate country
where you are located.
The Modem will only operate with Tone Dialing; Selection of Pulse dialing is not possible.
Please see below instruction for quick modem setup.
A. If you are located in Australia
1. Go to Control panel, select modem icon.
2. Choose Australia in “What country/region
are you in now?”
3. Select Phone system as “Tone Dialing”
4. Close
B. If you are located in New Zealand
1. Go to Control panel, select modem icon.
2. Choose New Zealand in “What country/
region are you in now?”
3. Select Phone system as “Tone Dialing”
4. Close
Note: Modem setting in Windows XP
A. If you are located in Australia
1. Click Start select Control panel select "Phone and
Modem Options".
2. Double click New Location.
3. Choose "Australia" in Country/region pull down
menu bar.
4. Select Phone system as “Tone Dialing”.
5. Click OK and Apply.
B. If you are located in New Zealand
1. Click start select Control panel select "Phone and
Modem Options".
2. Double click New Location.
3. Choose "New Zealand" in Country/region pull
down menu bar.
4. Select Phone system as “Tone Dialing”.
5. Click OK and Apply.
Note:
The screens and illustrations shown in this examples may slightly vary depending on the operating
environment that you have installed.
NOTATION IN THIS DOCUMENT
Warnings
This manual uses a variety of icons as visual marks so that you can use this computer safely
and correctly and avoid damage and danger to yourself and to others. These icons and their
meanings are as follows. Please learn these icons before reading this manual. Learning these
icons will be useful for understanding this manual.
Icon
Meaning
WARNING
Incorrect handling ignoring this warning can cause a dangerous situation
that could result in death or severe injury.
CAUTION
Incorrect handling ignoring this warning can cause a dangerous situation
that could result in moderate or minor injury or could result in equipment
damage.
The symbols below are used together with the icons above to indicate what type of danger or
damage is involved.
symbols
Meaning
The symbol indicates a w arning or caution. The symbol indicates
the concrete nature of the warning. (The example on the left is a caution for electric shock.)
The circle and slash indicates prohibited behavior. The symbol inside
the circle indicates the concrete nature of the prohibition. (The example
on the left indicates that disassembly is prohibited.)
indicates instructions that must be followed. The symbol inside
The
indicates the concrete nature of those instructions. (The example on
the left tells you to unplug the power plug from the socket.)
Key notation and operation methods
Explanations of key operations do not show all the characters on the keyboard. Instead they
indicate just the keys necessary to the explanation as follows.
Examples: [Ctrl] key, [Enter] key, [ → ] key
When multiple keys are to be pressed at the same time, this is indicated by connecting them
with [+].
Examples: [Ctrl] + [F3] keys; [Shift] + [ ↑ ] key
Screen examples
The screens shown in this manual are examples. Please understand that the file names and
screens you use may be different.
Notation in text
Here is what symbols in text mean.
Symbol
Critical Points
Meaning
Critical Point Indicates a point necessary for correctly operating the
hardware or software.
Column Gives the meaning and brief explanation of a term.
Column
→
Indicates the page to see elsewhere in this manual.
Command input (key input)
Within the text of this manual, command input (giving commands to the computer by pressing
keys) is indicated as follows.
Example:
dir c:
↑
In the position indicated in the example above by the ↑, the space left between the characters
indicates that a space needs to be left in the entry by pressing the space bar (the long key with
nothing written on it at the center of the front of the keyboard). Commands are written in this
manual as lowercase latin letters, but uppercase letters may be used.
Product names
The following product names are abbreviated as follows in this manual.
“Microsoft® Windows XP® operating system” is written as “Windows XP”.
“Microsoft® Windows® 2000 operating system” is written as “Windows 2000”.
“Microsoft® Millennium® Edition operating system” is written as Windows Me”.
“Microsoft® Windows® 98 operating system” is written as “Windows 98”.
“Windows NT 4.0” and “Windows NT 3.51” are both written as Windows NT.
“LifeBook” is written as “this computer” or “the computer main unit”.
SECTION 2
This section explains installation of options for this computer.
SECTION 3
This section explains what to do when trouble occurs with this computer and when messages
are displayed. Read this section as the necessity arises.
SECTION 2
This section explains basic operations and basic items for using this computer, including the
names of the parts and their functions, flat point operation methods, floppy disk unit handing,
and battery operation.
SECTION 3
SECTION 1
SECTION 1
Configuration of this Manual
CONTENTS
SECTION 1
1
Names of the Parts and their Functions .......................... 2
Front features of the computer .........................................................
Left/right features of the computer ...................................................
Rear features of the computer ..........................................................
Bottom features of the computer ......................................................
Status indicator LCD ........................................................................
2
2
4
7
8
9
Pointing Device ................................................................. 11
About the Flat Point ........................................................................ 11
How to use the Flat Point ............................................................... 12
3
Keyboard ........................................................................... 14
Keyboard ........................................................................................ 14
4
Replacing the Internal Battery Pack ............................... 18
1
Options .............................................................................. 22
SECTION 2
Options ........................................................................................... 22
Peripherals ..................................................................................... 23
Precautions for PC Cards ............................................................... 24
2
Using a PC Card ............................................................... 24
Installing a PC card ........................................................................ 26
Ejecting a PC card .......................................................................... 27
3
Using a CD/DVD ................................................................ 30
Loading a disc ................................................................................ 32
Ejecting the disc ............................................................................. 34
4
Expanding Memory .......................................................... 37
5
Using a Mobile Multi-bay Unit ......................................... 41
6
Connector Box .................................................................. 44
Installing the connector box ............................................................ 44
Removing the connector box .......................................................... 45
7
About the Internal Modem ............................................... 46
8
Using Internal LAN ........................................................... 48
Connecting a LAN cable ................................................................. 49
9
Connecting a USB Device ............................................... 51
Connecting a USB device ............................................................... 52
10 LifeBook Security/Application Panel .............................. 53
LifeBook Security / Application Panel .............................................
Setting up your LifeBook Security Panel ........................................
Passwords ......................................................................................
Operating your LifeBook Security/Application Panel ......................
Precautions ....................................................................................
Uninstalling the security Panel Application .....................................
Connecting a LAN cable .................................................................
E-Mail Notification LED ..................................................................
Configuring your LifeBook Application Panel .................................
Configure your E-mail Account Settings .........................................
Desktop Control Panel ....................................................................
53
53
54
55
56
56
57
58
58
61
66
11 Connecting a Mouse ........................................................ 68
Connecting a USB mouse .............................................................. 68
12 Printer ................................................................................ 70
Connecting Printer .......................................................................... 70
13 Connecting an External Display ...................................... 72
Connecting an external display ...................................................... 72
SECTION 3
1
When This Happens ......................................................... 76
2
Care and Maintenance ..................................................... 81
3
Glossary ............................................................................ 86
SECTION 1
SECTION
SECTION
1
This section explains basic
operations and basic items for
using this computer, including the
names of the par ts and their
functions, Flat point operation
methods, floppy disk unit handing,
and battery operation.
SECTION 1
1 Names of the Parts and their Functions
Front features of the computer
1
2
3
4
5
6
7
8
9
1
LCD display
The monitor of your computer.
Critical Points
About the characteristics of LCD displays
For reasons of characteristics specific to LCD displays, the following phenomena may occur
but they are not defects in your LCD display.
• The TFT color liquid crystal display (LCD) of you computer consists of more than
2,350,000 pixels (dots) (if the resolution is 1024x768), which are arranged in rows and
columns through the utilization of high-level technology. For technical reasons, however,
some dots on your LCD display may not light up or be always lit, but this does not mean
that the display is defective.
• There may be a slight difference in color between your LCD display and another LCD
display because of differences in manufacturing condition. Moreover, your LCD display
may produce colors somewhat unevenly because of temperature changes, etc.
2
Status indicator LCD
Displays the operating status of the computer.
3
Built-in microphone
Used for sound recording.
2
The microphone may cause a howling noise when you are using, for example, a karaoke
software program for which the microphone needs to be used along with the internal speakers.
If howling occurs, adjust the volume on your computer or use commercially available
headphones or an external microphone. When the microphone is not in use, you should cut
it off (mute).
The built-in microphone may not pick up all the sounds depending on the distance or direction
from the sound source. It is recommended that you use an external microphone if you want
to record sounds clearly.
4
One-touch buttons/Security panel
These buttons are used to set/reset security lock, password input during power on of the PC unit
and application start-up.
5
SUS/RES (Suspend/Resume) switch
Used to turn on your computer, to put it into standby (suspending operation) mode, or to resume
system operation.
6
Speakers
A sound output device of the computer
7
Keyboard
Allows you to type in letters and give commands to the computer.
8
Flat Point
Used to move the mouse pointer on the screen. The scroll button at the center allows you to
scroll a window up or down.
Critical Points
For some applications, windows may not be scrolled using the scroll button.
9
Latch
This latch locks the liquid crystal display (LCD) to avoid accidental opening.
Press it to unlock and open the LCD.
3
SECTION 1
Critical Points
Left/right features of the computer
❑ Left panel of the computer
1
1
23
Mobile multi-bay
Your computer came with a Combo Drive (DVD & CD-RW) or DVD drive built into this bay.
Depends which model you have.
Critical Points
To avoid damage to your computer, do not use the computer when the mobile multi-bay is
vacant.
2
Mobile multi-bay unit release lever
Raise the lever when removing the unit from the mobile multi-bay.
3
Antitheft lock port
Used to connect a commercially available antitheft cable.
Critical Points
The antitheft lock port supports the Kensington’s Micro Saver Security System.
When an anti-theft lock is connected, the mobile multi-bay unit cannot be removed.
4
SECTION 1
❑ Right panel of the computer
123 4 5 6
7
89
!
CAUTION
HEARING LOSS
• Before connecting a cable to the headphone jack, LINE IN jack, or microphone jack,
lower the volume on the computer to a minimum by pressing the [F8] key while
holding down the [Fn] key. Otherwise, the device connected could sustain damage
or a very loud noise could impair your hearing.
1
Microphone jack
Used to connect a commercially available monaural microphone (with a f3.5-mm mini plug) for
sound recording.
Some types of microphones (e.g., dynamic microphones) cannot be used with your computer.
So before purchasing a microphone, make sure it is compatible with your computer.
2
LINE IN jack/Optical digital audio output terminal
• LINE IN jack
This is an analog input (LINE IN) terminal used to connect the computer to the LINE OUT
terminal of an AV system (with a 3.5-mm stereo mini plug).
5
3
Headphone jack
Used to connect commercially available headphones (with a f3.5-mm mini plug). Headphones
with some types of plugs cannot be connected. So before purchasing headphones, make sure
they are compatible with your computer.
CAUTION
HEARING LOSS
• Don’t raise the volume too high especially when you are listening with headphones.
Listening to very loud sound for a long time could impair your hearing.
HEARING LOSS
• Don’t turn on or off the computer while you are wearing headphones, or noise could
impair your hearing.
4
Modem port
This connector allows you to connect the computer to a telephone line and enables PC
communications and Internet connection through the modular cable.
5
LAN port
Used to connect the computer to a local-area network (LAN) via an optional LAN cable so that
you can use your computer on a network or connect to the Internet.
6
Main switch
Used to turn on your computer.
7
PC card slot
Used to install a PC card.
Critical Points
Your computer came with a dummy card in the PC card slot.
8
PC card eject/lock button
Used to eject the PC card. This button also prevents the PC card from accidentally coming out of
the slot.
9
IEEE 1394 (DV) port
Used to connect a peripheral device, e.g., a digital video camera (DV), to the computer via a DV cable.
!
USB port
You can connect separately available USB standard peripherals such as a FDD unit or printer to
this port.
6
SECTION 1
Rear features of the computer
1
2
3
4
5
1
Infrared Communication Port
It is the interface to conduct infrared communication.
2
Cooling fan
Used to discharge heat out of the computer. The cooling fan automatically starts rotating when
the temperature in the computer rises to a specific level.
CAUTION
FAILURE
•
Do not block the air vent, otherwise the temperature in the computer will rise and
sometimes cause damage to the computer.
3
USB port
You can connect separately available USB standard peripherals such as a FDD unit or printer to
this port.
4
External display connector
Used to connect an optional external display, such as a CRT display.
5
DC-IN connector
This is the connector to connect the AC adapter supplied to the computer.
IMPORTANT
•
When you connect peripheral devices to each corresponding connector, confirm the
correct direction of the connector and insert directly into the connector.
7
Bottom features of the computer
1
2
3
4
1
Expansion RAM (Random Access Memory) module slot
The memory module on your computer is installed here.
If needed, you can increase the amount of memory by replacing the memory module.
2
Release button
Slide this button to unlock the internal battery pack.
3
Internal battery pack lock
Slide this to install or remove the internal battery pack.
4
Internal battery pack
An internal battery pack is installed here.
8
1 2
3
SECTION 1
Status indicator LCD
4 5
6
789
Critical Points
No indicator is displayed on the status indicator LCD when the main switch is turned off,
except when the computer is being recharged.
1
SUS/RES Indicator (
)
This indicator comes on when the computer is running and blinks in standby status.
2
AC Adapter Indicator (
)
This indicator comes on when the power is supplied from the AC adapter.
3
Battery installation indicator ( 1, 2,
)
This indicator appears when the battery is installed. The numbers 1 and 2 indicate the internal
battery and an optional add-on battery installed in the mobile multi-bay, respectively.
Battery Charge Indicator (
)
This indicator appears when the battery is charged.
Remaining Battery Power Indicator (
)
This indicator indicates the remaining battery power.
4
CD Access Indicator (
)
This indicator appears when a CD or DVD is accessed.
5
Hard Disk Access Indicator (
)
This indicator appears when the internal hard disk is accessed.
9
Critical Points
If you turn off the main switch or operate the SUS/RES switch while the hard disk access
indicator is showing, the data on the hard disk may be corrupted.
6
PC Card Access Indicator ( 1 )
This indicator appears when a PC card is accessed.
7
Num Lock (Numerical Lock) Indicator ( 1 )
This indicator appears when the keyboard is set to ten-key mode. You can activate and deactivate
the ten-key mode by pressing the [
] key.
8
Caps Lock Indicator ( A )
This indicator appears when the keyboard is set for all capital letters. You can activate or deactivate
the Caps Lock mode by pressing [
] key.
9
Scroll Lock Indicator (
)
This indicator appears when the scroll lock is activated to avoid screen scrolling. You can set and
reset the scroll lock by pressing the [
] key while holding down the [
] key.
The operation varies depending on the application when this indicator appears.
10
SECTION 1
About the Flat Point
The Flat Point is a handy pointing device that enables you to move the mouse pointer freely with
your finger. It consists of a touch-pad, left and right buttons on this side of the touch-pad, and the
scroll button between the left and right buttons.
The touch-pad has the same function as the ball in a mouse. You can move the mouse pointer in any
directions on the screen by sliding the tip of a finger on the touch-pad. Moreover, if you tap the touchpad with a finger, you can click, double-click, point to, or drag any object on the screen.
The left and right buttons correspond to the left and right buttons of a mouse, and their functions
vary from application to application.
Pressing the scroll button forward or backward enables you to easily scroll a window up or down.
Touch-pad
Touch-pad
Left button
Scroll button
Right button
Critical Points
The Flat Point may malfunction if condensation occurs or if it is moistened. In addition, if you
operate it with a moistened or sweaty finger, or if the Flat Point surface is dirty, the mouse
pointer may not move correctly. In such a case, turn off your computer and wipe dirt off with
a soft cloth slightly dampened with dilute detergent.
Some applications do not allow you to use the scroll button to scroll windows.
You can use an optionally available USB mouse instead of the Flat Point.
11
SECTION 1
2 Pointing Device
How to use the Flat Point
•
Click
or
•
“Click” means quickly pressing the left button once or
tapping the touch-pad once.
Pressing the right button once is called “right-click.”
Double-click
“Double-click” means pressing the left button twice in a
row or tapping the touch-pad twice in a row.
or
•
Point
“Point to an item” means moving the mouse pointer onto
a menu item, and so on, to select it. Pointing to an item
highlights it and displays an explanation about it. If the
item to which you pointed has a submenu (such items
are marked with ), the submenu appears.
•
Drag
To drag an object, move the mouse pointer onto the
object, move the object to the desired location by sliding
the finger on the touch-pad while holding the left button
down, and then move the finger off the pad. Or, move
the mouse pointer onto the object, and tap the touchpad twice in a row. After that, without moving the finger
off the pad, slide it to move the object to the desired
location, and then move the finger off the pad.
or
•
Scroll
To return, push
this forward.
To advance, push
this backward.
12
To scroll a window, click anywhere in the window and
push the scroll button forward or backward to scroll the
window.
You can change the functions assigned to the right and left buttons and also adjust the
mouse speed, using the Mouse Properties dialog box. To display this dialog box, click the
Printers and other hardware icon in the Control Panel window and select Mouse.
When tapping the touch-pad, tap it quickly with the tip of a finger but not strongly.
The mouse pointer moves in the same direction as you slide a finger on the touch-pad. If the
finger reaches one edge of the pad before you move the pointer to the desired location,
move the finger off the pad temporarily, put it in an adequate place on the pad and start
sliding the finger again.
❑ Using the scrolling function
The scroll button enables you to easily scroll a window.
1
Click any place in the area (of the window) that you want to scroll.
(The illustration varies depending on the model and use conditions.)
2
Move the scroll button forward and backward.
The window scrolls in the same direction you moves the button.
To return, push this forward.
To advance, push
this backward.
13
SECTION 1
Critical Points
SECTION 1
3 Keyboard
Keyboard
❑ Names and functions of the principal keys
Keys that can be used as ten-keys
2
1
3 4 5
Num Lk
Scr Lk
Insert
Prt Sc
Delete
SysRq
Pause
Break
8
6
9
>
.
.
<
,
7
!
?
/
/
Fn
!
@
#
$
%
^ & *
1
Esc (Escape) key
Used to cancel the current task and return to the previous task.
2
Function keys
Functions assigned to these keys vary from application to application.
3
Num Lk (Numerical Lock) key
Pressing the [
] key activates the ten-key mode. To deactivate the ten-key mode, press it
once again.
4
Insert / Prt Sc (Print Screen) key
• Insert key
Used to specify whether to overwrite an existing string or to insert a new string.
• Prt Sc (Print Screen) key
Used to save the currently displayed windows as pictorial data (bitmap file). To do so, press
the [
] key while holding the [
] key down.
To save only the active window as pictorial data, press the [
] key while holding the
[
] and [
] keys down.
Using painting software (e.g., Paint), you can edit, save, and print pictorial data. To do so,
you need to import it to the painting software by selecting the Paste command from the Edit
menu.
14
Delete key
Used to delete the character on the right of the cursor. With this key, you can also delete the file
or icon you selected.
By pressing the [
] key while holding the [
] and [
] keys down, you can forcibly
terminate the out-of-control application or computer.
6
Caps Lock key
To fix to the English Capital mode, press the [
] key while holding the [
To deactivate the English Capital mode, press these keys again.
] key down.
7
Shift key
Used in combination with other keys. By pressing a key while holding the [Shift] key down, you
can enter the character or symbol printed in the upper case of the key.
8
Back Space key
Used to delete the character on the left of the cursor.
9
Enter key
Used to confirm the string entered.
In text processing, pressing this key inserts a hard return in the text. That’s why this key is also
called the Return key.
0
Pg Up (Page Up) key/Cursor keys
Used to return to the previous page. To do so, press the [ ] key while holding the [
down.
Used to move the cursor upward, downward, to right and left.
] key
15
SECTION 1
5
!
Fn key
This key, specific to your computer, is used in combination with other function keys, as described
below.
• [Fn]+[F3] : Turns on or off the sound output (internal speaker and headphones).
- Adjusting the sound volume
• [Fn]+[F4] : Enables or disables the Flat Point.
- Connecting a mouse
• [Fn]+[F5] : Switches between Full-Screen mode and Normal Display mode (display in the
center of the screen) when the resolution is set to a lower value than the default value.
- Switching between Full-Screen mode and Normal Display mode
• [Fn]+[F6] : Dims the LCD display.
- Adjusting the brightness of the LCD display
• [Fn]+[F7] : Brightens the LCD display.
- Adjusting the brightness of the LCD display
• [Fn]+[F8] : Turns down the volume.
- Adjusting the sound volume
• [Fn]+[F9] : Turns up the volume.
- Adjusting the sound volume
• [Fn]+[F10] : When an external display is connected, this combination of keys can be used to
switch between the LCD display and the external display.
- Switching displays
*:
The plus sign means that you need to press the key on the right of the plus sign while holding down the
key on the left of it. e.g.) [Fn]+[F3] : Press and hold [Fn], and press [F3] without releasing [Fn].
@
Ctrl key
Used in combination with other keys.
#
Windows key
Used to open the Start menu.
$
Alt key
Used in combination with other keys.
%
Application key
Used to open the pop-up menu for the item selected.
This key has the same function as the right button of the Flat Point.
^
Home key/Cursor keys
Used to move the cursor to the beginning of the line on which it is currently placed. To do so,
press the [ ] key while holding the [
] key down. Pressing the [ ] key while holding the
[
&
] and [
] keys down causes the cursor to move to the beginning of the text.
Pg Dn (Page Down) key/Cursor keys
Used to display the next page. To do so, press the [ ] key while holding the [
Used to move the cursor upward, downward, to right and left.
16
] key down.
End key/Cursor keys
Used to move the cursor to the end of the line on which it is currently placed. To do so, press the
[
] key while holding the [
] key down. Pressing the [
] key while holding the [
] and
[
] keys down causes the cursor to move to the end of the text.
Used to move the cursor upward, downward, to right and left.
❑ About the ten-key mode
The ten-key mode refers to the mode that enables you to use certain character entry keys as tenkeys (a key arrangement that makes it easy to type in figures). To activate the ten-key mode, simply
press the [
] key. In the ten-key mode, 1 is displayed on the status indicator LCD. The figure
you can enter with a ten-key is marked on the front surface of the key. Note that connecting an
optional ten-key pad disables the ten keys on your computer.
17
SECTION 1
*
SECTION 1
4 Replacing the Internal Battery Pack
WARNING
ELECTRIC SHOCK
• Before replacing the battery pack, be sure to turn off the computer and disconnect
the AC adapter from it. Also, don’t touch any connector of the computer or battery
pack to avoid electric shock or malfunction.
❑ Replacing the internal battery pack
1
Turn off the power to the computer and disconnect the AC adapter.
2
Close the LCD display and turn the bottom side of the computer up.
3
Release the lock.
(1) Slide the internal battery pack lock while sliding the release button in the direction of the
arrow, and (2) release the lock.
Release button
Internal battery pack lock
(1)
(2)
18
Remove the internal battery pack.
Put a finger in the indentation opened as a result of sliding the internal battery pack lock, and lift
the internal battery pack.
Internal battery pack lock
Indentation
Internal battery pack
5
Install a new battery pack.
Insert the new battery pack diagonally into the bay and push it down until it is set in place.
6
Slide the internal battery pack lock until it clicks into place.
(1) Slide the internal battery pack lock to the right end, and (2) make sure that the red-colored
part of the release button is completely hidden.
Internal battery pack lock
Red-colored part
(2)
(1)
19
SECTION 1
4
2
This section explains installation
of options for this computer.
SECTION 2
SECTION
SECTION
SECTION 2
1 Options
Options
You can expand the functions of this computer by connecting various options.
Numerical keypad
Printer
External
display
Built-in DVD-ROM
drive unit
FDD unit (USB)
Mouse
USB mouse
Digital video
camera
Memory
PC card
Built-in CD-R/RW
drive unit
Built-in battery pack
Built-in Super disk
drive unit
USB devices: Supported by Windows XP, Windows
2000, Windows 98 and Windows Me
only
22
Peripherals
Some setting up works are required for a certain peripherals
You cannot use some PC peripherals just by connecting it to a PC. Those peripherals require
some setting up work after connection. For example, printers and PC cards require “driver
installation” work after connecting them. And memory and other peripherals do not require such
setting up works. Make sure to consult with this document for the peripheral connection to
complete the work correctly.
See also the documents for the peripherals
The peripheral installation methods shown in this document are only a few examples. Make
sure to consult with the documents for the peripherals as well as this document.
Use genuine products
Use genuine optional device from our company. We cannot guarantee proper function on this
PC for the peripherals from other sources. When it is necessary to use the peripheral from the
other source, consult with the manufacturer of the product.
Use the peripherals that conform to ACPI standard
This PC is set to ACPI mode for Windows XP, Windows 2000 and Windows 98. Power save and
other functions may not work correctly if a peripheral does not conform to ACPI mode.
Notes on installation/removal
The installation of the peripheral must be done after the setting up of an operating system
except for a PS/2 mouse. The set-up function might not complete correctly if such a peripheral is
attached before the operating system set up.
Critical Points
When you connect a peripheral to a connector, make sure that the direction of the connection
is correct and connect straight.
When you connect more than one peripherals, complete setting for each peripherals before
installing others.
23
SECTION 2
Below explanation is necessary for your knowledge before connecting your peripherals.
SECTION 2
2 Using a PC Card
Precautions for PC Cards
Observe the following points when using PC cards to prevent breakdown.
Do not place PC cards in high- Do not subject PC cards to Avoid rubbing PC cards and
temperature locations and strong shocks.
building up static electricity.
locations subject to direct
sunlight.
Do not place heavy objects on Be careful to avoid spilling coffee When storing a PC card, always
top of PC cards.
and other liquids on PC cards. place it in its special case.
24
❑ Caution in using PC cards
CAUTION
A PC card is composed of parts very sensitive to static electricity, and it may be
damaged even by static built up in a human body. Before handling a PC card, always
touch a metal object with your hand to discharge static.
You should pay attention to the following points when you use PC cards in order to prevent
failure
• Avoid exposing PC cards to direct sunlight or high temperature.
• Avoid subjecting PC cards to shocks.
• Do not place heavy objects on top of them.
• Avoid getting PC cards wet.
• Store PC cards in their cases when not in use.
❑ PC cards that can be used with your computer
Your computer is compatible with PC Card Standard-compliant Type I PC cards and Type II PC
cards. Here are some examples of these types of cards.
•
•
Adapter card
This PC card is needed to load pictorial data from a smart media for digital cameras into
the computer.
SCSI Card
This PC card is needed to connect a SCSI device, such as a SCSI hard disk or MO
(Magneto-Optical) drive.
Critical Points
Your computer does not support PC cards with a working voltage of 12V.
❑ Preparing necessary items
PC card
Prepare a PC card that meets your need.
PC card driver
A CD or floppy disk that contains the PC card driver is supplied with
some PC cards.
Manual of the PC card
Setting procedures vary depending on the PC card used. So be
sure to read also the manual of your PC card.
25
SECTION 2
FAILURE
•
Installing a PC card
CAUTION
INJURY
•
Do not put your finger into the PC card slot when you install a PC card, or you may
be injured.
Critical Points
It may be required to turn off the power to the computer or to install a device driver when you
install a specific PC card. Check with the manual supplied with each PC card.
1
Eject the dummy card from the PC card slot.
Raise and press the PC card eject/lock button to eject the dummy card.
PC card eject/lock button
Dummy card
2
Install a PC card.
Insert the PC card into the PC card slot as far as it will go, with the labeled face facing upward.
PC card
26
Lock the PC card.
Fully pull out the PC card eject/lock button, collapse it backward, and lock the PC card with the
fitting.
SECTION 2
3
PC card eject/lock button
4
If the PC card is being installed for the first time, install any necessary driver.
Some PC cards require the installation of a driver. Check the manual supplied with each PC
card and install a driver if required.
A floppy disk or a CD may be required to install a driver.
5
Click the
icon (Safely Remove Hardware) in the lower right corner of the screen
(notification area where a clock is displayed), and make sure that the name of the PC card
inserted is displayed correctly.
- If the name of the PC card is displayed, click any vacant area on the desktop. in the “Ejecting
a PC card” section, and insert the PC card again.
Critical Points
When you use a PC card attached with a cable, do not put anything heavy on, or apply a
shock to, the connector of the cable connected with the PC card, or it may damage the
equipment.
Ejecting a PC card
Critical Points
When you remove a PC card attached with a cable, do not pull the cable connected to the
PC card or it will result in failure.
When you remove a PC card, follow the procedure below or it will result in failure.
Some PC cards require shutting down when you remove them. Consult with the manual of
the PC card.
27
CAUTION
HIGH TEMPERATURE
• A PC card may be quite hot right after use. Wait for a while before removing a PC
card after Step 3, to avoid burning your fingertips.
INJURY
•
1
When you remove a PC card, do not insert your finger into the PC card slot to avoid
cutting your fingertips.
Click the
icon (Safely Remove Hardware) in the lower right corner of the screen
(notification area where a clock is displayed).
Critical Points
Don’t eject the PC card by clicking the Stop button in the Safely Remove Hardware dialog
icon (Safely Remove Hardware) in the
box that appears when you double-click the
lower right corner of the screen (notification area where a clock is displayed). Doing so may
cause your computer to become unstable.
2
If the PC card is being installed for the first time, install any necessary driver.
XXXXXXXX refers to the name of the PC card inserted.
3
When the message “Remove Hardware” appears, raise the PC card eject/lock button.
PC card eject/lock button
28
4
Eject the PC card.
Press the PC card eject/lock button to eject the PC card.
SECTION 2
PC card eject/lock button
PC card
5
Install the dummy card.
Insert the dummy card into the PC card slot as far as it will go, fully pull out the PC card eject/
lock button, and collapse it backward to lock the dummy card.
PC card eject/lock button
Dummy card
29
SECTION 2
3 Using a CD/DVD
In this manual, CD-ROMs, music CDs and CD-R/RW discs are collectively referred to as CDs,
and DVD-ROMs and DVD-VIDEOs are referred to as DVDs.
CAUTION
INJURY
•
When inserting or ejecting a CD or DVD, don’t put any fingers on the disc tray to
prevent possible injury to them.
❑ Caution in handling a CD/DVD
Keep the following in mind when using a CD/DVD.
• When you unscrew the screws on your PC, use the cross-point screwdriver with the
appropriate size for the screws. Using screwdrivers other than that may damage the head of
screws.
•
When taking out a disc from the case or loading it in your computer, don’t touch any surface
of it.
• Handle a disc with care so as not to put fingerprints on it, to make it dirty or dusty, or to
scratch it, otherwise no data could be read from it, written or rewritten on it. Soiled audio
CDs or DVD-VIDEOs may not be played back normally.
• Don’t stick any label on any surface of a disc, or write anything to it with a ball-point pen or
pencil.
• Be careful not to spill coffee or any other liquid over a disc.
• When a disc is dirty or condensation occurs on it, wipe the disc radially from the center with
a slightly moistened cloth, then with a dry cloth. Don’t use a hairdryer to dry it or don’t let a
wet disc dry naturally.
• Don’t use benzene, thinner, water, record cleaner, antistatic spray, or silicone cloth to clean
discs.
• Always keep discs in their cases when they are not in use.
• Don’t bend a disc or put any heavy object on top of it.
• Don’t store discs in an extremely hot or cold place.
CD-ROM,
audio CD,
video CD,
photo CD
CD-R
CD-RW
DVD-ROM,
DVD-VIDEO
Reading (playback)*1
O
O
O
O*2
Writing
X
O
O
X
Rewriting
X
X
O
X
*1: Note that some types of discs cannot be used with your computer or application software may be required
to play them.
*2: DVD-ROMs refer to DVDs containing information, including programs with which you can see the data on
computer displays.
DVD-VIDEOs refer to DVDs on which sound and pictorial data are recorded.
DVD-RAM, DVD-RW, DVD+RW, or DVD-Audio discs cannot be used with your computer.
30
When you purchase CD-R/RW discs be sure check whether they meet the data writing and rewriting
speeds of your drive.
Don’t use CDs or DVDs other than round discs (e.g., deformed discs, including star-shaped
discs and card-type discs).
Data cannot be read/written correctly from/on a deformed disc or a deformed disc could
cause the CD/DVD drive to fail.
The region code of your computer’s DVD drive is 3. DVD-VIDEOs with a country-specific
region code may not be used with your drive if their region codes don’t agree with that of
your drive.
Some DVD discs are copy-protected for copyright protection. Your computer has Descramble
and Authentication features to prevent unauthorized duplication of DVDs, so that if data
protected by copyright is copied, it cannot be played because of an authentication error.
31
SECTION 2
Critical Points
Loading a disc
IMPORTANT
•
•
•
•
1
You should preferably power the computer from the AC adapter when frequently accessing
a CD or playing back a DVD-VIDEO.
To set a disc on the disc tray, align the center of the disc with the projection at the center
of the tray and push the disc down until it clicks into place.
Otherwise it may come off in the drive, causing damage to the disc tray and drive or the
disc itself.
When you are using a disc that starts automatically when it is loaded, don’t put your
computer into standby mode. If you place the computer into standby (suspending
operation) mode while using an auto-run CD, the CD will start twice when you resume
system operation (when you restore the operation at the point at which you suspended
operation), and this could cause the computer to malfunction. If you let the CD start
twice, exit all programs on the CD, and load it over again.
When data is being read, the CD/DVD runs at very high speeds and sometimes causes
vibration and hiss noise.
Press the CD eject button.
The disc tray pops out a little.
CD eject button
2
Pull out the tray gently.
Disc tray
32
If the tray does not come out
- If you have already shut down Windows, turn your computer back on and press the CD
eject button.
If the main switch is in the Off position ( ), slide it to the | position to turn on the computer,
and then press the CD eject button.
You may press the CD eject button even when the
icon is blinking on the status indicator
LCD.
3
Set a disc on the tray while holding the tray.
Align the hole of the disc with the projection at the center of the tray with the labeled surface up,
and push the disc down until it clicks into place. Failure to fit a disc correctly onto the projection
could prevent the disc from being ejected.
Disc tray
Projection
4
Push the tray gently into the computer.
It takes about 10 seconds for your computer to get ready to start the loaded disc.
Disc tray
33
SECTION 2
Critical Points
Critical Points
If a message appears, asking you what to do “If a disc containing this kind of file is inserted
...,” click “No, ...” and click OK.
When you load a multi-session CD, it may take much time for your computer to get ready to
start.
If you insert an audio CD in your computer while Windows is running, CD Player application
starts automatically to play it. You can use the one-touch buttons or CD Player to perform the
following operation.
Ejecting the disc
1
Exit the application you started from the disc.
2
Press the CD eject button.
The tray pops out a little.
CD eject button
34
3
Pull out the tray gently.
SECTION 2
Disc tray
Critical Points
If the tray does not come out
- If you have already shut down Windows, turn your computer back on and press the CD
eject button.
- If the main switch is in the Off position ( ), slide it to the | position to turn on the
computer, and then press the CD eject button.
You may press the CD eject button even when the
icon is blinking on the status indicator
LCD.
4
Take out the disc while holding the tray with a hand.
To detach the disc, lift the edge of the disc while holding the projection with a finger.
Disc tray
Projection
35
5
Push the tray gently into the computer.
Critical Points
If the disc won’t come out:
1. Click the Start button, and select My Computer.
2. Move the mouse pointer onto the CD Drive icon in the My Computer window.
3. Press the right button once on the Flat Point.
4. Click Eject.
The tray pops out a little.
5. Pull out the tray gently and take out the disc from it.
If you cannot eject the disc by this method, follow these steps.
1. Turn off your computer.
2. Insert a straightened paper clip, etc., into the pinhole on the right of the CD eject button.
The tray will pop out a little.
3. Pull out the tray gently and take out the disc from it.
CD eject button
36
SECTION 2
4 Expanding Memory
Memory (Expanded RAM
module)
You can additionally install memory.
Philips screwdriver
(Size: #1)
Used to remove the screw securing the cover. Use a Philips
screwdriver that meets the size of the screw (M2.0). Using a
screwdriver of other size may cause damage to the screw head.
❑ Replacing memory
WARNING
ELECTRIC SHOCK
• Before replacing memory, always turn off your computer and disconnect the AC
adapter from it, or you could get an electric shock.
SWALLOWING
• The cover, cap, screw, etc., removed could choke babies and children if they are
swallowed accidentally. To avoid danger of suffocation, always keep them out of the
reach of babies and children.
In the event any of these items is swallowed, consult a doctor immediately.
37
SECTION 2
❑ Preparing necessary items
CAUTION
FAILURE
•
FAILURE
•
FAILURE
•
When replacing memory, don’t touch its terminals or ICs but hold its edges. Also, be
careful not to touch any components or terminals inside the computer. Touching a
terminal with oily fingers could cause poor contact.
Memory is composed of parts very sensitive to static electricity, and it may be
damaged even by static built up in a human body. Before handling memory, always
touch a metal object with your hand to discharge static.
Before replacing memory, be sure to turn off the computer. Replacing while the
computer is in standby or hibernation mode could cause damage to the computer
or memory.
Critical Points
Be sure to install memory on your computer before turning on the computer.
To avoid damage, be careful not to drop a screw removed, etc., in the computer.
1
Turn off the computer and disconnect the AC adapter.
2
Close the LCD display, and turn and place the computer upside down.
3
Remove the two screws shown in the following figure and detach the expansion RAM
module slot cover.
Detach the expansion RAM module slot cover at the bottom of the computer.
Slot cover
38
4
Remove the memory.
Disengage the two tabs securing the memory on both sides, and pull the memory out of the slot.
SECTION 2
Tab
Memory
5
Install a new RAM module.
Align the notch in the RAM module with the protrusion on the connector, diagonally insert the
RAM module into the slot, and push it down until it clicks into place.
Notch in the RAM module
Notch in the
RAM module
6
Attach the expansion RAM module slot cover as it was.
Attach the cover that was detached in step 3.
Slot cover
39
❑ Checking the size of the memory installed
IMPORTANT
•
If memory is not installed correctly, the message “Extended memory error” appears or
nothing is displayed on the screen when you turn on the computer. In such a case, turn
off the main switch of your computer and reinstall the memory.
1
Turn on the computer.
2
Click the Start button, and select Control Panel.
The Control Panel window appears.
3
Click Performance and Maintenance and then System.
The System Properties dialog box appears.
4
Make sure that the circled numerical value in the figure below has increased by the size
of the memory you added.
The figure shows an example of the expansion of 256 MB of memory.
Depending on the system configuration, the memory size displayed may be 1 MB smaller than
the actual memory size.
5
Click OK.
The Control Panel window appears again.
Critical Point
If the memory size displayed is incorrect, check whether the memory is installed properly.
40
SECTION 2
5 Using a Mobile Multi-bay Unit
Take the following precautions when using a multi-bay unit to avoid damage to it.
• The internal DVD-ROM & CD-R/RW drive (that came with your computer) is very sensitive
to vibration and shock as it rotates a disc at a very high speed. To prevent a breakdown
in the drive and data corruption, do not move the computer or apply shock or vibration to
it while the disc is being accessed.
• Do not store a mobile multi-bay unit in an extremely hot or cold place or where the
temperature can greatly change.
• Do not place a mobile multi-bay unit where it will be exposed to direct sunlight or bring
it close to any heat generating apparatus.
• Do not use a mobile multi-bay unit where it will be exposed to shock or vibration.
• Do not use a mobile multi-bay unit in a damp or dusty location.
• Do not use a mobile multi-bay unit if a foreign object such as water or metal chips has
gotten in it. If any foreign object has gotten in it, contact the Fujitsu Customer Support
Center or your Fujitsu retailer.
• When a mobile multi-bay unit is dirty, wipe it gently with a dry, soft cloth or a soft cloth
moistened with water or detergent diluted with water. Never use volatile liquids such as
benzene or thinner.
• Do not disassembly or take apart any mobile multi-bay unit.
• Do not use or store a mobile multi-bay unit near an apparatus producing a strong magnetic
field.
41
SECTION 2
❑ Cautions in using a mobile multi-bay unit
1
If your computer is in Suspend mode, press the SUS/RES button to resume operation.
2
Click the
icon (Safely Remove Hardware) in the lower right corner of the screen
(notification area where a clock is displayed).
3
Select the device you want to unplug or eject and then click Stop.
XXX refers to the name of the mobile multi-bay unit currently in use.
4
Remove the unit.
(1) Raise the mobile multi-bay unit release lever, and
(2) Safely pull out the DVD/CD-RW drive
(2)
(1)
42
5
SECTION 2
6
Press the SUS/RES button.
The computer goes into Suspend mode.
Install a new unit.
Push in the unit as far as it will go with the connector-mounted face facing forward.
7
Press the SUS/RES button again to resume operation.
IMPORTANT
•
•
To avoid damage to your computer, always use it with a mobile multi-bay unit installed in
the bay.
Raise the mobile multi-bay unit release lever only when removing the mobile multi-bay
unit. If you raise the lever by mistake, the lock may be released. In such a case, turn off
your computer, remove the unit, and reinstall it.
43
SECTION 2
6 Connector Box
The connector box is described here.
IMPORTANT
•
•
The connector box can be installed/removed regardless of the condition of the PC. If the
FDD unit is connected to the FDD unit connector of the connector box, however, install/
remove the connector box after switching the PC power off.
Certain peripheral devices connected to the connector box may operate unstably if the
connector box is installed/removed while the PC power is on. If this happens, switch the PC
power off prior to installing/removing the connector box.
Installing the connector box
This section describes how to install the connector box.
If any peripheral device is connected to the PC rear side, remove it beforehand.
CAUTION
INJURY
•
1
Be careful not to catch your fingers in the space between the PC and the connector
box when installing it. It may cause an injury.
Install the connector box to the PC bottom side.
Fitting the connectors on the PC and the connector box, lower the PC horizontally (1), lightly
press the parts shown below (2), and firmly set the connector box.
2
2
1
Connector box
connection
connector
IMPORTANT
•
•
44
To install a peripheral device to or remove it from the connector box, be sure to switch the
PC power off and disconnect the AC adapter in advance.
Do not carry the PC with the connection box installed. The connectors on the PC and/or the
connector box may be damaged.
Removing the connector box
1
If any peripheral device is connected to the connector box, switch the power off.
2
Release the connector box lock.
Release the lock by sliding the connector box removal lever.
SECTION 2
This section describes how to remove the connector box.
Removal lever
3
Remove the connector box.
While keeping the removal lever in the unlocking position (1), lift the side having the connector
first (2) then the other side of the PC (3) to remove the connector box.
2
1
3
45
SECTION 2
7 About the Internal Modem
Your computer has a V.90-compliant built-in fax modem.
WARNING
ELECTRIC SHOCK
• Do not insert your fingers into a modular jack, or you may receive an electric shock.
CAUTION
FAILURE
•
When using a modular cable, always connect it to a modular connector, otherwise
your computer could break down.
❑ Connecting a modular cable
1
Turn off the power to the computer and disconnect the AC adapter.
2
Insert the supplied modular cable into the modular connector on the right panel of the
computer.
Insert firmly until it clicks.
Modular connector
3
Disconnect your telephone’s modular cable from the modular jack of the telephone line.
Pull it out while pressing in the
clip of the modular cable.
46
IMPORTANT
Modular type
4
Rosette type
Connect the modular cable to the modular jack of the telephone line.
Insert the plug on the other end of the cable you have connected to the computer in Step 1.
Critical Points
Follow these steps to check whether the device driver has been installed correctly.
1. The telephone is not usable with its modular cable disconnected. Do not forget to connect
it for telephone use after finishing Internet communication.
2. A modular cable may not be connected to your computer if it is routed around a household
electrical appliance, or wound and tied in an bundle.
3. If the supplied modular cable is too short to connect your computer to a modular jack for
the telephone line, purchase a commercially available modular cable with a proper length.
Note that the use of a long modular cable may result in a transmission failure or a
reduction in the transmission rate.
4. Do not connect a modular cable to the LAN port, otherwise your computer could break
down.
❑ Caution in using the internal modem
Connecting to the Internet for a long time while still running some applications applies a
considerable load on the CPU of the computer. It may lead to interruption of communication via
the internal modem. In this case, exit all applications you are running except your browser and
e-mail software before accessing the Internet again.
47
SECTION 2
If your telephone line connector is rosette type, it must be changed to a modular type.
If such a change is necessary, have it done by an authorized person. You can also ask your
telephone company to do the work.
SECTION 2
8 Using Internal LAN
Your computer has a built-in LAN device, so that it can be connected to a 10BASE-T or 100BASETX network.
❑ Preparing necessary items
LAN cable
LAN cables are available in two types: straight type and cross
type. You need to use a cable that meets the data transfer rate of
the network. So refer to the manual for the network device to
which you intend to connect your computer and prepare an
adequate cable.
Network device
Prepare a device that meets the objective of network connection.
Here are some examples of network devices.
• Network Adapter
• Network Cable
• Hub
48
Connecting a LAN cable
WARNING
ELECTRIC SHOCK
• If it thunders, immediately turn off the computer and disconnect the AC adapter and
LAN cable from it. Lightning could cause damage to the computer and cause a fire
in the worst case.
CAUTION
ELECTRIC SHOCK
• Don’t put any finger into the LAN port, or you could get an electric shock.
FAILURE
•
Be sure to plug a LAN cable correctly in the LAN port. Failure to do so could cause
your computer to fail.
1
Turn off your computer and disconnect the AC adapter.
2
Plug a LAN cable in the LAN port on the right panel of the computer.
LAN port
3
Plug the LAN cable in the network device.
Connect the other end of the LAN cable that you connected in step 2, to the LAN port of the
network device, then turn on the network device.
49
SECTION 2
ELECTRIC SHOCK
• Before connecting a LAN cable, always turn off your computer and disconnect the
AC adapter, or you could get an electric shock.
4
Connect the AC adapter to the computer and turn the power on.
5
Click the Start button and select Control Panel.
6
Click Performance and Maintenance, then Power Option.
7
Click
of “System standby” on the Power Schemes tab, and select “Never.”
8
Click
of “System suspended” and select “Never.”
9
Click OK.
10 Make all necessary network settings.
IMPORTANT
•
•
When you are connecting to a local area network (or the Internet) using the LAN function,
you should not put your computer into Standby or Hibernation mode. Doing so could
cause your computer to break connection with the network or the Internet, depending
on the environment in which your computer is being used.
Turn off your computer if you are not using the computer for the connection.
Your computer is configured by default so that the LAN device will not operate if you turn
on the computer before connecting a LAN cable to it when the computer is powered by
the internal battery.
Critical Points
When disconnecting the LAN cable from the LAN port, pull it while pushing in the tab to
avoid damage to the plug.
When using the LAN device, you should preferably power your computer from the AC adapter
since the LAN device consumes a large amount of electrical power.
The built-in LAN device in your computer cannot be used along with any LAN card.
If the LAN device does not operate normally, make all necessary settings.
To avoid damage to the LAN device, do not connect a LAN cable to a modular jack.
50
SECTION 2
9 Connecting a USB Device
❑ Preparing necessary items
Devices that can be connected to USB ports. Here are some typical
examples of USB devices. Prepare a USB device that meets your
needs.
•
•
•
•
•
•
•
Digital camera
CCD camera
Mouse
Printer
Scanner
Keyboard
Speaker
USB cable
Used to connect a USB device to the computer. Some USB
devices come with a USB cable. For some USB devices, e.g.,
USB mice, the USB cable is an integral part of them. For more
information, refer to the manual for the USB device you want to
connect.
USB device driver
Some USB devices come with a CD or floppy disk that contains
their respective drivers. Refer to the instruction manual for the USB
device and use one that is compatible with Windows installed on
your computer.
Manual for USB device
Ways of connection vary from USB device to USB device. So be
sure to read also the manual for the USB device used.
Critical Points
Each USB port is capable of supplying up to 500mA to the USB device connected if the
device requires no power supply from any other source. For more information, refer to the
instruction manual for your USB device.
51
SECTION 2
USB device
Connecting a USB device
1
Connect a cable to the USB device you want to use.
2
Plug the other end of the cable in the USB port of your computer.
Insert the cable with the USB connector’s
-marked surface facing upward.
USB port
or
USB port
3
Install the device driver.
Some USB devices get ready for use only if being connected and they don’t require the installation
of a driver. For more information, refer to the manual for the USB device used.
Critical Points
If the Install Hardware dialog box appears when you connect a USB cable, click Continue to
install the device driver.
52
SECTION 2
10 LifeBook Security/Application Panel
LifeBook Security / Application Panel
(1) Application A Button
(2) Application B Button
(3) Internet Button
(4) E-mail Button
SECTION 2
Enter Button
Sus/Res Button
A unique feature of your LifeBook is the Security/Application Panel that allows you to secure
your LifeBook from unauthorized use. The Security/Application Panel also allows you to launch
applications with a touch of a button when your system is on. If the security system is activated,
upon starting your LifeBook or resuming from suspend mode the security system requires
you to enter a password code using the buttons on the Security/Application Panel. After
entering a correct password, your LifeBook resumes system operation. (Refer diagram above)
Setting up your LifeBook Security Panel
Numbered Buttons
Use these buttons to enter your password.(Refer diagram above)
Enter Button
After entering the button strokes, push this button to enter the password into the LifeBook.
(Refer diagram above)
53
Passwords
The user and supervisor password may be set on this LifeBook. A supervisor password is
typically the same for all LifeBooks in a working group, office, or company to allow for system
management. Individual LifeBooks in a group environment should not use a common
password. A password consists of one to five button strokes plus the enter button. A valid
stroke consists of pushing one or up to four buttons simultaneously. The following are valid
button strokes:
• Pushing [4] by itself
• Pushing [2] and [3] at the same time
• Pushing [1], [2], and [4] at the same time
• Pushing [1], [2], [3], and [4] at the same time
The following are valid passwords. The numbers within braces ({ }) are button strokes using more
than one button.
• {[2]+[3]}, [1], [enter]
• [4], [enter]
• {[1]+[3]}, {[2]+[3]+[4]}, [1], [4], [2], [enter]
Setting Passwords
When shipped from the factory, no passwords are set. You have a choice of having no password
or setting a supervisor and user password. You must set the supervisor password before the
user password.
Critical Points
The purpose of supervisor password is to be able to bypass the user password in case the
user password is forgotten. The supervisor password alone will not lock the system.
You have to set both the supervisor and user passwords for the security panel to work.
Setting Supervisor Password
You must have set a supervisor password before setting any user passwords. The supervisor
password can bypass the user password.
1. Go to the Start menu.
2. Click on Run.
3. Type in FJSECS.EXE, then press [Enter]
4. Follow the on-screen instructions to set the Supervisor password.
54
Setting User Password
1. Go to the Start menu.
2. Click on Programs.
3. Click on Security Panel Application and Set User Password.
Critical Points
You may change or remove the supervisor or user password by repeating the steps defined
above.
Operating your LifeBook Security/Application Panel
The security lock feature is in effect both when the system resumes from Off or suspend
state. You always need to push the Suspend /Resume button to input the user password. Your
system will not begin the boot sequence without entering your supervisor/user password.
From Off State
1. Turn on your system.
2. When the Security Indicator flashes, enter the password and press Enter button. For example,
if the password is 22222, Press Button Number 2 five times and press Enter button.
The LifeBook will boot to normal operation.
From Suspend State
1. Press your Suspend/Resume button.
2. When the Security Indicator flashes, enter the password and press Enter button. The LifeBook
should resume normal operation.
Incorrect Password Entry
If an invalid supervisor or user password is entered three times in succession, the system will
“beep” for about one minute. If a valid password is entered within a minute (while system beeps),
the beeping will stop and the LifeBook will resume normal operation. If no or an invalid password
is entered while the system beeps, the system will return to its previous locked state (suspend or
off) and the Security Indicator will go off. To reactivate the LifeBook after a password failure, you
must press the Suspend/Resume button, then enter a correct password.
55
SECTION 2
4. Follow the on-screen instructions to set the User password.
Critical Points
Remember the user password you specified on the Security Panel Application. If you forget
the password you will not be able to use your computer. The supervisor password can override
the user password.
Precautions
Opening and Closing the Cover
Closing the cover automatically places the LifeBook into suspend mode. Opening the cover
does not automatically place the LifeBook into normal operation. Instead, you must enter the
proper security password after pushing the Suspend/Resume button.
Low Battery Operations
If your LifeBook has low battery, pushing the suspend/ resume button only turns on the Security
Indicator. Your LifeBook does not unlock, the Security Indicator turns off after one minute. To
resume normal operation, first attach a power supply to the LifeBook. Then you may unlock the
LifeBook.
Uninstalling the security Panel Application
You have two options when uninstalling the security panel application:
• Uninstall the security panel application software. This will disable all security feature.
• Uninstall the security panel application with password still active. This will not allow any changes
to the password.
Uninstalling the Security Panel Application Software
Remove passwords when User wants no password protection whatsoever and doesn’t want to
give anybody the utility to set a password on their computer. In this case, if passwords (supervisor,
user, or both) are set, the passwords must first be cleared BEFORE removing the application. To
clear passwords, follow same procedure in SETTING PASSWORD CODES except this time,
select REMOVE, enter current password then click Next. When asked to confirm select Yes.
Removing Security Panel Application With Password still Active
Using this feature will not allow any changes to the password.
Critical Points
Removing the applications does not remove the password. It simply removes the utility to
change/ add/ remove passwords. To change your password you must reinstall the application.
56
User:
1. Go to Start Menu, Click on Control Panel.
2. Open Add/Remove Programs Properties in the Control Panel.
3. Select the Security Panel Application in the list, and click Add/Remove.
Supervisor:
1. Go to Start Menu, Click on Control Panel.
2. Open Add/Remove Programs Properties in the Control Panel.
3. Select the Security Panel Application for Supervisor in the list, and click Add/Remove.
4. When the Confirm File Deletion box appears, click Yes.
Reinstalling the Security/Application Panel
To reinstall supervisor or user security application, you will need your Software Drivers CD
where the programs is located at LifeBook_Options\Security Panel.It contains the setup files for
supervisor and user security application.
1. Double-click the Setup SETUPS.EXE file. The Installing Security Panel Application window
will appear. Follow the instructions on the screen.
2. Double-click the Setup SETUP.EXE file. The Installing Security Panel Application window
will appear. Follow the instructions on the screen. Supervisor and user passwords can be
set by the Windows Software which are FJSECS.EXE and FJSECU.EXE respectively.
FJSECU.EXE for user password cannot run without supervisor password. First you need to
run FJSECS.EXE to set supervisor password before setting user password. Follow instructions
under Setting Passwords.
The LifeBook Security Panel is designed to prevent theft or unauthorized access to your LifeBook. It
is important that you remember the password that has been set in your LifeBook otherwise the
LifeBook will not be able to operate or resume from suspend.
The LifeBook Security Panel is a high security feature. Should you forget the password that you have
set, you are required to return your LifeBook to:
LifeBook Security Panel Administrator
Fujitsu PC (Asia) Pte Ltd
238A Thomson Road, #24-01/05
Novena Square Tower A
Singapore 307684
Note: The authorised Fujitsu Service Center will not be able to reset the password. Please remember
to keep your password in a safe place.
There is a service charge for unlocking the password restricted LifeBook.
Email: www.fujitsu-pc-asia.com\contactus
57
SECTION 2
4. When the Confirm File Deletion box appears, click Yes.
E-Mail Notification LED
By setting up the E-mail LED notification in conjunction with your E-mail button setup, you can
connect to your ISP, check for and retrieve new mail, terminate connection, and activate the E-mail
LED to notify that new mail has arrived.
To use the E-mail LED notification, you must have access to a POP3 Server with no Security Password
Authentication. Contact your service provider to determine if they support POP3 without Security
Password Authentication.
Critical Points
E-mail Notification LED is available on select LifeBook notebook models only.
Configuring your LifeBook Application Panel
When you start Windows, the LifeBook Application Panel is automatically activated.
As an application launcher, the LifeBook Application Panel is very flexible, giving you a variety of
options. To set up the Panel to best suit your needs, we have provided the Application Panel Setup
utility that quickly and easily helps you make the most of this valuable feature.
To configure your LifeBook Application Panel with Application Panel Setup:
1. Click on Start.
2. Click on Control Panel.
3. Click on Application Panel.
58
Label
Button Function
Default Application
1
Application A
Notepad
2
Application B
Calculator
3
Internet
Internet Explorer
4
E-Mail
Outlook Express
SECTION 2
The Application Panel Setup utility will appear. There are tabs that correspond to the application
buttons on the LifeBook Application Panel. When you receive your notebook, these buttons are
configured to launch specific applications. Below is the example of applications associated with
each button.
Critical Points
The tabs in Application Panel Setup may not be in the same order as the buttons on your
LifeBook notebook. Please carefully select the tab you wish to change.
To change an application associated with the Application A, Application B, or E-mail buttons, click on
the tab for the button you would like to reconfigure – for example, Application A. Click on Browse
from Start Menu, scroll down the list of applications, click on the application you wish to launch with
this button, and then click OK. The button will now launch the new application.
The Internet tab is different. It comes set to launch your default Windows Internet browser, (Internet
Explorer, unless changed.) In order to reconfigure it to launch another program follow these easy
steps:
1. Click on Other from the Internet browser box.
2. Click on Browse from Start Menu.
3. Scroll down the list of applications, and the click on the application you wish to launch
with this button.
4. Click OK.
59
The button will now launch the new application. If you want to return to launching your Windows
default Internet browser with this button, you need only click on “Default Internet Browser” from the
Internet browser box. Be aware that you will erase the settings for the “other application”. If you wish
to go back to launching the “other application” from this button, you will need to reconfigure it as
described above.
When you have finished with Application Panel Setup click on OK, and the new settings will take
effect. You can reconfigure your LifeBook Application Panel as often as you like.
Critical Points
The Internet or E-mail buttons can be configured to launch any application you wish, not just
an Internet browser or e-mail program.
Enabling/disabling Application Launcher button (Select Models Only)
At the bottom of each application setup page are two selectable options. The first will “Keep this
button active even on Standby”, and the second will “Keep this button active even on Hard Drive
Timeout”. You can enable/disable either or both of these functions simply by check or unchecking
the check Box.
60
Configure your E-mail Account Settings
The E-mail Notification LED is available on select LifeBook notebook models only.
To use the E-mail LED notification, you must have access to a POP3 Server with no Security
Password Authentication. Contact your service provider to determine if they support POP3
without Security Password Authentication.
To configure the E-mail Account Settings:
1. Click on Start.
2. Click on Control Panel.
3. Click on Application Panel.
4. Click on the E-Mail tab.
5. Click on E-Mail Account Settings...
6. The E-Mail Setup screen appears. Choose the type of connection: LAN or Dial Up.
61
SECTION 2
Critical Points
• If LAN: Click on LAN. Enter the POP3 Server name, your account name and password for that
account. Consult your Service provider if you do not know or are unsure of the information
requested.
• If Dial Up: Click on Dial Up. Choose the Dial up configuration (as previously set in Dial Up
Networking) you wish to retrieve mail from. Enter the POP3 Server name, your account name
and password for that account. The account name and password should be the same
information you entered in the Dial Up configuration. After all the information has been entered,
test the connection by clicking on “Testing connection with current setting”. If an error occurs,
check the settings and information on Dial Up Network and E-mail LED notification.
After the setup (Dial Up Networking/E-mail/E-mail LED) is completed, you are ready to retrieve mail.
When you press the E-mail button, your system will establish connection with your provider, check
for and retrieve new mails, terminate the connection, and activate the blinking LED to alert you of
new mail.
To configure After checking mail
This setting let you set your computer to return back to the previous power saving state after checking
mail.
62
SECTION 2
To configure Auto Mail Check
This function allow you to specify day and time for checking new mail. Only applicable when the PC
stays Standby.
To configure Mail Check Interval
This function allow you to specify an interval (minutes) for checking for a new mail during you use the
computer. Recommendation of this function use with LAN connection.
63
To configure Special recipient
This function allow you to add a special recipient on the Address List.
You have to specify from the Mail Check Interval to check the check box of Periodically check for
New Mail from the menu Mail Check Interval.
There is an icon like envelop appear on the taskbar. Refer diagram below
64
SECTION 2
To configure Important Mail
This function allow you to change the icon color on the taskbar to notifies you that an important mail
comes.
To configure Sound
This allow you to change the LifeBook Application icon’s color on the taskbar and beeps each time
you receive a new message.
65
Desktop Control Panel
Your LifeBook notebook includes a CD Player control panel. You may use this panel to operate the
Disc Player.
To use the desktop control panel:
1. Click on Start.
2. Click on All Programs.
3. Click on LifeBook Application Panel.
4. Click on Display CD Player.
The CD Player will appear in the upper left corner of your screen.
To close the panel, click on the “x” button. To minimize the panel, click on the “-” button.
You can select from four appearances for your CD Player. Simply double click on the track display
area of the panel, and a menu will appear which will allow you to select from a pull down menu. On
the CD Players Options menu box, you have an options to select : Always on top, Continuous play
and Disable Stop/Eject Button from the CD removal. If you click on “Always on top” the desktop
controls will always be seen on your screen, no matter what other application you are running. If you
click on “Continuous Play”, your Disc Player will automatically start over at the beginning as soon as
it finishes the last track. By default the Eject Button is disable from the CD Player Options. Once you
click the Eject button from the CD Player, the drive will not eject. If you want the Eject Button to be
function, uncheck this options.
66
SECTION 2
You can change the CD Player design by selecting the setting from the pull down menu from the CD
Player options.
Grey (High Color)
Circle (High Color)
Stick (High Color)
Basic (16 colors)
You can move the CD Player to anywhere on your desktop. Drag it by clicking on the track number
display, holding it down, and dragging the control panel.
When you have placed it where you would like, release the mouse button.
Critical Points
If you have your display set to 256K colors the basic display will appear no matter which one
you select. You will need to set your display colors to more than 256K in order to select other
display appearances.
When you close the Disc Player’s desktop control panel, it will stop the audio Disc Player.
Precautions
• LifeBook Application Panel uses the date and time settings of your LifeBook notebook. If the date
and time are off, you can adjust this setting in the Windows Control Panel.
• If you insert an audio CD which has both audio and data tracks into the Disc Player, the Disc
Player may fail to play the first audio track.
• The Volume Up, Volume Down and Mute controls for the Disc Player desktop control panel adjusts the volume of the CD audio line only. It does not adjust your notebook’s master software
volume control or the manual volume on the LifeBook notebook.
• The Disc Player desktop control panel is designed to be displayed in High Color (16-bit) or in True
Color (24-bit or more). If you have your notebook’s display set for 256 colors or less, the Disc
Player control panel will display in a “basic” mode.
67
SECTION 2
11 Connecting a Mouse
Connecting a USB mouse
1
Plug the USB mouse cable in the USB port of the computer.
Align the connectors by matching their shapes and insert the connector of the mouse straight
into the USB port of the computer.
USB port
or
USB port
Critical Points
A USB mouse can be connected and disconnected even when the computer is on.
Connecting a USB mouse does not automatically disable the Flat Point. To disable the Flat
Point, follow the steps described in the next section, “Disabling the Flat Point.”
❑ Disabling the Flat Point
When a USB mouse is connected to your computer, not only the mouse but also the Flat Point
are enabled. To disable the Flat Point, follow these steps.
1
After Windows starts, press the [
] key while holding the [
] key down.
The Flat Point switches between Enabled and Disabled each time you press the [
] key while
holding the [
] key down. When you activate or deactivate the Flat Point, the message “Internal
pointing device: Enabled” or “Internal pointing device: Disabled” appears on the screen,
respectively.
IMPORTANT
•
68
Don’t disable the Flat Point before connecting a USB mouse to your computer.
Even when you disable the Flat Point by pressing the [
] key while pressing down the
[
] key, the Flat Point is enabled after restarting or resuming operation of the computer. To
disable it, you need to press the [
] key again while holding the [
] key down.
The Flat Point can be turned on and off manually only when the “Internal pointing device”
item is set to “Manual” under “Keyboard/Mouse Settings “ in the BIOS Setup Advanced
Menu. If the Manual option is unselected, select it.
If you set the “Internal pointing device” item of the “Keyboard/Mouse Settings” in the BIOS
Setup Advanced Menu to “Always disabled”, the Flat Point is always disabled.
69
SECTION 2
Critical Points
SECTION 2
12 Printer
This section describes connection of a printer to the parallel connector on the connector box.
With a printer, you can print the documents and images that are generated on the PC.
Critical Points
If the printer is one corresponding to USB connection, the USB connector can also be used
for connection.
Connecting Printer
WARNING
ELECTRIC SHOCK
• To connect/remove a printer, be sure to switch the PC power off and disconnect the
AC adapter beforehand. Otherwise you may undergo an electric shock.
CAUTION
FAILURE
•
When connecting cables, read this manual well to avoid misconnection.
If the PC is used with a wrong connection, the PC and/or the printer may be damaged.
1
Switch the PC power off and disconnect the AC adapter.
2
Install the connector box.
3
Connect the printer cable to the parallel connector on the connector box.
When viewed from the front, the connectors are in a trapezium shape.
Study the shapes of the connectors and firmly insert the cable connector (1), then fix it, tightening
the left and right screws on it (2).
Parallel connector
(2)
(1)
Printer cable
70
Connect the printer cable and the power cable to the printer.
Refer to the printer manual for the details on connection.
Some printers may already have their power cables fixed on them.
5
Insert the printer power cable plug to a receptacle and switch the printer power on.
6
Connect the AC adapter to the PC and switch the PC power on.
7
If the printer is connected for the first time, install the driver.
Read the printer manual to install the driver.
Floppy disk(s) or CD(s) may be used for driver installation.
SECTION 2
4
Critical Points
Printer connection needs a printer cable. Some printer packages may not include a printer
cable.
In addition, the printer cable that is attached to the printer may not be used due to a different
connector shape. If this is the case, obtain a separately available cable that can be connected
to the PC.
The printer connection procedures differ depending on your printer. Refer to the printer
manual for the details.
71
SECTION 2
13 Connecting an External Display
❑ Preparing necessary items
External display
Prepare an external display that supports PC/AT-compatible or DOS/
V computers.
Display cable
Cables for connection between a computer and an external
display. Generally, an external display comes with a separate
cable or a cable fixed to the back.
If no display cable is included with your external display or if the
cable connector is not compatible with your computer, prepare a
display cable that is designed for PC/AT-compatible or DOS/V
computers and that has a connector compatible with the external
display.
Manual for the external
display used
Ways of connection vary from display to display. So be sure to read
also the manual for the external display used.
Connecting an external display
This section explains how to connect a CRT display to the external display connector on the rear
panel of your computer.
WARNING
ELECTRIC SHOCK
• Before connecting or disconnecting an external display to your computer, always
turn off the computer and disconnect the AC adapter from it. Failure to do so could
lead to an electric shock.
CAUTION
FAILURE
•
72
Before connecting a cable, read this manual carefully so that you can connect it
correctly.
Connecting a cable incorrectly could cause your computer and external display to
break down.
Turn off the computer and disconnect the AC adapter from it.
2
Connect the display cable to the external display connector on the rear panel of your
computer.
A display cable connector has a trapezoidal cross section.
Adjust the orientation of the connector, (1) insert the cable connector, and (2) secure the display
cable with the screws on both sides of the connector.
SECTION 2
1
External display connector
Display cable
3
Connect the display cable to the CRT display.
For the way to connect the cable, refer to the manual for your CRT display.
4
Plug the power cable of the CRT display in a wall outlet and turn it on.
5
Connect the AC adapter to the computer, turn it on, and then switch displays.
- Switching displays
Critical Points
The following may take place when you turn on your computer for the first time after connecting
an external display to it.
- Images are displayed on both the computer’s LCD display and the external display.
- The Add New Hardware Wizard dialog box appears.
In this case, follow the on-screen instructions to install the display driver.
73
3
This section explains what to do
when trouble occurs with this
computer and when messages
are displayed. Read this section
as the necessity arises.
SECTION 3
SECTION
SECTION
SECTION 3
1 When This Happens
When you are having trouble with this computer, there is something you think is strange, or
there is something you want to do, but do not know how. This section is divided into related
items.
The power does not come on.
Checkpoint
Cause and Solution
Is the AC adaptor connected? When using this computer for the first time after purchase, the
battery is not yet charged, so you must connect the AC adaptor
and turn on the main switch.
Is the main switch turned on?
If the main switch is not turned on, the power will not come on
even if the SUS/RES button is pressed.
Is the battery charged?
If a beep is heard when the main switch is turned on, then the
battery is running low (LOW BATTERY). Connect the AC
adaptor.
Has the computer been left
unused for a long time?
When using the computer for the first time after leaving it
unused for a long time, connect the AC adaptor and switch on
the main switch to switch on the power.
Nothing displayed on the LCD panel
Checkpoint
Is
displayed on the LCD
panel?
AC
100/240V
Is anything displayed on the
status indicator LCD?
76
Cause and Solution
• Displayed
Adjust the brightness and darkness with the brightness and
contrast controls.
• Flashing or not displayed
Press the SUS/RES button to put the computer into operating
mode. Check if the battery is charged. If it is not charged,
connect the AC adaptor and charge it.
If you are already using this computer with the AC adaptor
connected, check that it is correctly plugged into the power
socket and into the computer.
Connect the AC adaptor and switch on the main switch.
Checkpoint
Cause and Solution
Have you been pressing any
of the keys?
On this computer, if the power management functions are set
and no key is pressed for a certain period of time, the CPU
stops and the LCD panel backlight goes out. (In this state,
pressing any key lights up the backlight again.) If the computer
stops too frequently, change the BIOS setup settings.
Is it set to output to the CRT?
Switch over to the LCD display with the [Fn] + [F10] keys.
LCD panel hard to read
Checkpoint
Is the control adjusted?
Cause and Solution
Adjust the brightness with the brightness and contrast controls.
Battery is not charged
Cause and Solution
Check that the AC adaptor is correctly plugged into the power
socket and into the computer.
Is the battery overheated
(The
on the LCD display
flashes.)?
If the ambient temperature is high and the battery temperature
becomes too high during use, the battery protection function
may be triggered to stop the charging.
Is the computer too cold
on the LCD display
(The
flashes.)?
If the battery temperature falls too low, the battery protection
function may be triggered to stop the charging.
Was the charging stopped
midway?
If you use the computer and disconnect the AC adaptor
between the start of charging and the time the
LCD turns
off, then the battery will not become fully charged.
Once you start charging do not remove the AC adaptor until the
LCD turns off.
77
SECTION 3
Checkpoint
Is the AC adaptor connected?
The remaining battery charge indicator does not stop flashing.
Checkpoint
Cause and Solution
Is the battery connected
correctly?
Check that the battery is connected correctly. If it is connected
correctly, there is an abnormality in the battery pack, so replace
the battery pack.
Is the battery low?
Attach the AC adaptor and charge the battery.
Floppy disk can not be used.
Checkpoint
Cause and Solution
If the floppy disk loaded into
the floppy disk drive correctly?
Insert the floppy disk with its label facing up, into the drive
shutter and keep inserting firmly until you hear a clicking sound.
Is the floppy disk formatted?
New floppy disks can not be used until they are formatted
(initialized). Format the floppy disk.
Is Diskette A set to Not
Installed in the BIOS setup?
Check the Diskette A item in the BIOS setup Main menu.
Is Diskette access set to
Supervisor only in the BIOS
setup?
Check the Diskette access item in the BIOS setup Security
menu.
Is the floppy disk write
inhibited?
Set the write protect tab on the floppy disk to the write enable
position.
Does it work with a different
floppy disk?
If it works with a different floppy disk then the problem floppy
disk may be damaged.
78
No sound or minimal sound from speaker
Checkpoint
Is the volume control
correctly adjusted?
Cause and Solution
Turn the volume control for the correct volume. If this does not
change the volume, double click the task bar sound indicator
and adjust the volume. Check also whether the sound driver is
installed correctly.
Checkpoint
Cause and Solution
Is the mic correctly adjusted?
Turn the volume control to obtain the correct volume. If the line
jack is connected to the sound source, then check that
connection. If this still does not solve the problem, then double
click the task bar sound indicator and adjust the volume.
LCD panel does not close.
Checkpoint
Is something caught in the
LCD display panel?
Cause and Solution
Forcing the LCD display panel closed can damage it. Check for
something caught in the LCD display panel. Also, a metal object
such as a paper clip can cause a breakdown if it gets caught in
between the keys.
The power management function is not executed.
Checkpoint
Cause and Solution
Is Power Savings set to off in
the BIOS setup?
Reset the BIOS setup.
Are you executing a program
that rewrites the screen?
If you are executing a program that rewrites the screen even
when no key is pressed, for example a clock display or screen
save, the power management function is not executed.
79
SECTION 3
Can not record from Mic or Line In jack
Data cannot be read from the CD-ROM drive.
Checkpoint
Cause and Solution
Is the CD-ROM correctly set?
Set the CD-ROM correctly with its label facing upwards.
Is there any dirt,
condensation or water on the
CD-ROM?
Wipe it from the center outwards with a dry, soft cloth.
Is the CD-ROM scratched or
extremely warped?
Replace the CD-ROM.
Are you using a non-standard
CD-ROM?
Use a CD-ROM which conforms to the standards.
The CD cannot be ejected from the CD-ROM.
Checkpoint
Is it in operating mode?
80
Cause and Solution
The CD can only be ejected when the personal computer main
unit is in operating mode because its CD-ROM drive has an
electronic lock. Check that the personal computer main unit is in
operating mode and press the EJECT button. If for some
reason the CD tray does not come out even when you press the
EJECT button, insert a clip or somthing into the hole to the right
of the EJECT button and pull the tray out.
If the tray doesn’t still come out, click the CD-ROM icon in the
“My Computer” window with the right button of the mouse and
then click “EJECT”.
SECTION 3
2 Care and Maintenance
If you use your Fujitsu LifeBook notebook carefully, you will increase its life and reliability. This section
provides some tips for looking after the notebook and its devices.
Caution:
Electrical equipment may be hazardous if misused. Operations of this product or similar products,
must always be supervised by an adult. Do not allow children access to the interior of any electrical
products and do not permit them to handle any cables.
LIFEBOOK NOTEBOOK
Caring for your LifeBook Notebook
• Your LifeBook notebook is a durable but sensitive electronic device. Treat it with care.
• Make a habit of transporting it in a suitable carrying case.
• Do not attempt to service the computer yourself. Always follow installation instructions closely.
• Keep it away from food and beverages.
SECTION 3
• If you accidentally spill liquid on your notebook:
1. Turn it off.
2. Position it so that the liquid can run out.
3. Let it dry out for 24 hours, or longer if needed.
4. If your notebook will not boot after it has dried out, call your support representative.
• Do not use your LifeBook notebook in a wet environment (near a bathtub, swimming pool).
• Always use the AC adapter and batteries that are approved for your notebook.
• Avoid exposure to sand, dust and other environmental hazards.
• Do not expose your LifeBook notebook to direct sunlight for long periods of time as temperatures
above 140°F (60°C) may damage your notebook.
• Keep the covers closed on the connectors and slots when they are not in use.
• Do not put heavy or sharp objects on the computer.
• If you are carrying your LifeBook notebook in a briefcase, or any other carrying case, make sure
that there are no objects in the case pressing on the lid.
• Do not drop your LifeBook notebook.
• Do not touch the screen with any sharp objects.
Cleaning your LifeBook Notebook
• Always disconnect the power plug. (Pull the plug, not the cord.)
• Clean your LifeBook notebook with a damp, lint-free cloth. Do not use abrasives or solvents.
• Use a soft cloth to remove dust from the screen.Never use glass cleaners.
81
Storing your LifeBook Notebook
• If storing your notebook for a month or longer, turn your LifeBook notebook off and remove all
Lithium Ion batteries.
• Store your LifeBook notebook and batteries separately. If you store your notebook with a battery
installed, the battery will discharge, and battery life will be reduced. In addition, a faulty battery
might damage your notebook.
• Store your LifeBook notebook in a cool, dry location. Temperatures should remain between 25°C (13°F) and 60°C (140°F).
Travelling with your LifeBook Notebook
• Do not transport your LifeBook notebook while it is turned on.
• Do not check your LifeBook notebook as baggage. Carry it with you.
• Always bring your System Recovery CD that came with your LifeBook notebook when you
travel. If you experience system software problems while travelling you may need it to correct
any problems.
• Never put your LifeBook notebook through a metal detector. Have your notebook hand-inspected
by security personnel. You can, however, put your LifeBook notebook through a properly tuned
X-ray machine. To avoid problems, place your notebook close to the entrance of the machine
and remove it as soon as possible or have your notebook hand-inspected by security personnel.
Security officials may require you to turn your notebook On. Make sure you have a charged
battery on hand.
Outlet type
Location
United States, Canada, parts of Latin America, Japan, Korea,
the Philippines, Taiwan
Russia and the Commonwealth of Independent States (CIS),
most of Europe, parts of Latin America, the Middle East, parts
of Africa, Hong Kong, India, most of South Asia
Mexico, United Kingdom, Ireland, Malaysia, Singapore, parts of
Africa
China, Australia, New Zealand
82
• When travelling with the hard drive removed, wrap the drive in a non-conducting materials
(cloth or paper). If you have the drive checked by hand, be ready to install the drive if needed.
Never put your hard drive through a metal detector. Have your hard drive hand-inspected by
security personnel. You can however, put your hard drive through a properly tuned X-ray machine.
• Take the necessary plug adapters if you’re travelling overseas. Check the following diagram to
determine which plug adapter you’ll need or ask your travel agent.
BATTERIES
Caring for your Batteries
• Always handle batteries carefully.
• Do not short-circuit the battery terminals (that is, do not touch both terminals with a metal
object). Do not carry lose batteries in a pocket or purse where they may mix with coins, keys, or
other metal objects. Doing so may cause an explosion or fire.
• Recharge batteries only as described in this manual and only in ventilated areas.
• Do not leave batteries in hot locations for more than a day or two. Intense heat can shorten
battery life.
• Do not leave a battery in storage for longer than 6 months without recharging it.
Increasing Battery Life
• Power your LifeBook notebook through the AC or optional auto/airline adapater whenever
possible.
• If your LifeBook notebook is running on battery power all day, connect it to the AC adapater
overnight to recharge the battery.
• Keep brightness to the lowest level comfortable.
• Set the power management for maximum battery life.
• Put your LifeBook notebook in Suspend mode when it is turned on and you are not actually
using it.
• Limit your DVD/CD-RW/CD-ROM access.
• Disable the Windows CD automatic insertion function.
• Always use fully charged batteries.
• Eject PCMCIA cards when not in use.
FLOPPY DISKS AND DRIVES
Caring for your Floppy Disks
• Avoid using the floppy disks in damp and dusty locations.
• Never store a floppy disk near a magnet or magnetic field.
• Do not use a pencil or an eraser on a disk or disk label.
• Avoid storing the floppy disks in extremely hot or cold locations, or in locations subject to severe
temperature changes. Store at temperatures between 50°F (10°C) and 125°F (52°C)
• Do not touch the exposed part of the disk behind the metal shutter.
83
SECTION 3
• Do not drop, puncture, disassemble, mutilate or incinerate the battery.
Caring for your Floppy Disk Drive
• To clean, wipe the floppy disk drive clean with a dry soft cloth, or with a soft cloth dampened
with water or a solution of neutral detergent. Never use benzene, paint thinner or other volatile
material.
• Avoid storing the floppy disk drive in extremely hot or cold locations, or in locations subject to
severe temperature changes. Store at temperatures between 50°F (10°C) and 125°F (52°C)
• Keep the floppy disk drive out of direct sunlight and away from hating equipment.
• Avoid storing the floppy disk drive in locations subject to shock and vibration.
• Never use the floppy disk drive with any liquid, metal, or other foreign matter inside the floppy
disk drive or disk.
• Never disassemble or dismantle your floppy disk drive.
DVD/CD-RW/CDs
Caring for your DVD/CD-RW/CDs
• DVD/CD-RW/CDs are precision devices and will function reliably if given reasonable care.
• Always store your DVD/CD-RW/CDs in its case when it is not in use.
• Always handle DVD/CD-RW/CDs by the edges and avoid touching the surface.
• Avoid storing any DVD/CD-RW/CDs in extreme temperatures.
• Do not bend DVD/CD-RW/CDs or set heavy objects on them.
• Do not spill liquids on DVD/CD-RW/CDs.
• Do not scratch DVD/CD-RW/CDs.
• Do not put a label on DVD/CD-RW/CDs.
• Do not get dust on DVD/CD-RW/CDs.
• Never write on the label surface with a ballpoint pen or pencil. Always use a felt pen.
• If a DVD/CD-RW/CD is subjected to a sudden change in temperature, cold to warm condensation
may form on the surface. Wipe the moisture off with a clean, soft, lint free cloth and let it dry at
room temperature, DO NOT use a hair dryer or heater to dry DVD/CD-RW/CDs.
• If a DVD/CD-RW/CD is dirty, use only a DVD/CD-RW/CD cleaner or wipe it with a clean, soft,
lint free cloth starting from the inner edge and wiping to the outer edge.
84
Caring for your DVD/CD-RW/CD-ROM Drive
Your DVD/CD-RW/CD-ROM drive is durable but you must treat it with care. Please pay attention to
the following points:
• The drive rotates the compact disk at a very high speed. Do not carry it around or subject it to
shock or vibration with the power on.
• Avoid using or storing the drive where it will be exposed to extreme temperatures.
• Avoid using or storing the drive where it is damp or dusty.
• Avoid using or storing the drive near magnets or devices that generate strong magnetic fields.
• Avoid using or storing the drive where it will be subjected to shock or vibration.
• Do not disassemble or dismantle the DVD/CD-RW/D-ROM drive.
Caring for your PC Cards
PC Cards are durable, but you must treat them with care. The documentation supplied with your PC
Card will provide specific information, but you should pay attention to the following points:
• To keep out dust and dirt, store PC Cards in their protective sleeves when they are not installed
in your notebook.
• Avoid prolonged exposure to direct sunlight or excessive heat.
• Keep the cards dry.
• Do not flex or bend the cards, and do not place heavy objects on top of them.
• Do not force cards into the slot.
• Avoid dropping cards, or subjecting them to excessive vibration.
85
SECTION 3
PC CARDS
SECTION 3
3 Glossary
AC Adapter
A device which converts the AC voltage from a wall outlet to the DC voltage needed to power your
notebook.
Active-Matrix Display
A type of technology for making flat-panel displays which has a transistor or similar device for every
pixel on the screen.
APM
Advanced Power Management.
Auto/Airline Adapter
A device which converts the DC voltage from an automobile cigarette lighter or aircraft DC power
outlet to the DC voltage needed to power your notebook.
BIOS
Basic Input-Output System. A program and set of default parameters stored in ROM which tests and
operates your notebook when you turn it on until it loads your installed operating system from disk.
Information from the BIOS is transferred to the installed operating system to provide it with information
on the configuration and status of the hardware.
Bit
An abbreviation for binary digit. A single piece of information which is either a one (1) or a zero (0).
bps
An abbreviation for bits per second. Used to describe data transfer rates.
Boot
To start-up a computer and load its operating system from disk, ROM or other storage media into RAM.
Bus
An electrical circuit which passes data between the CPU and the sub-assemblies inside your notebook.
Byte
8 bits of parallel binary information.
Cache Memory
A block of memory built into the micro-processor which ins much faster to access than your system
RAM and used in specially structured ways to make your overall data handling tine faster.
CardBus
A faster, 32-bit version of the PC Card interface which offers performance similar to the 32-bit PCI
architecture.
CD-ROM
Compact disc read only memory. This is a form of digital data storage which is read optically with a
laser rather than a magnetic head. A typical CD-ROM can contain about 600MB of data and is not
subject to be crashing into the surface and destroying the data when there is a failure nor to wear
from reading.
86
CMOS RAM
Complementary metal oxide semiconductor random access memory. This is a technology for
manufacturing random access memory which requies very low level power to operate.
COMM Port
Abbreviation for communication port. This is your serial interface connection.
Command
An instruction which you give your operating system. Example: run a particular application or format
a floppy disk.
CRT
Cathode Ray Tube. A display device which uses a beam of electronic particles striking a luminescent
screen. It produces a visual image by varying the position and intensity of the beam.
Data
The information a system stores and processes.
DC
Direct current. A voltage or current that does not fluctuate periodically with time.
Default Value
A pre programmed value to be used if you fail to set your own.
DIMM
Dual-in-line memory module.
LAN
Local Area Network. An interconnection of computers and peripherals within a single limited
geographic location which can pass programs and data amongst themselves.
LCD
Liquid Crystal Display. A type of display which makes images by controlling the orientation of crystals
in a crystalline liquid.
Lithium ion Battery
A type of rechargeable battery which has a high power-time life for its size and is not subject to the
memory effect as Nickel Cadmium batteries.
LPT Port
Line Printer Port. A way of referring to parallel interface ports because historically line printers were
the first and latter the most common device connected to parallel ports.
MB
Megabyte.
87
SECTION 3
Configuration
The combination of hardware and software that make up your system and how it is allocated for use.
Megahertz
1,000,000 cycles per second.
Memory
A repository for data and applications which is readily accessible to your notebook CPU.
MHz
Megahertz.
MIDI
Musical Instrument Digital Interface. A standard communication protocol for exchange of information
between computers and sound producers such as synthesizers.
Modem
A contraction for MOdulator-DEModulator. The equipment which connects a computer or other data
terminal to a communication line.
Monaural
A system using one channel to process sound form all sources.
MPU-401
A standard for MIDI interfaces and connectors.
NTSC
National TV Standards Commission. The standard for TV broadcast and reception for the USA.
Operating System
A group of control programs that convert application commands, including driver programs, into the
exact form required by a specific brand and model of microprocessor in order to produce the desired
results from that particular equipment.
Parallel Port
A connection to another device through which data is transferred as a block of bits simultaneously
with a wire for each bit in the block and with other wires only for control of the device not for transfer
of data.
Partition
A block of space on a hard drive which is set aside and made to appear to the operating system as
if it were a separate disk, and addressed by the operating system accordingly.
PCMCIA
PCMCIA is trademark of the Personal Computer Memory Card International Association. The Personal
Computer Memory Card International Association is an organization that sets standards for add-in
cards for personal computers.
Peripheral Device
A piece or equipment which performs a specific function associated with but not integral to a computer.
Examples: a printer, a mode, a CD-ROM.
88
Pitch (keyboard)
The distance between the centers of the letter keys of a keyboard.
Pixel
The smallest element of a display, a dot of color on your display screen. The more pixels screen. The
more pixels per area the clearer your image will appear.
Disk
A spinning platter of magnetic data storage media. If the platter is very stiff it is a hard drive, if it is
highly flexible it is a floppy disk, if it is a floppy disk in a hard housing with a shutter it is commonly
called diskette.
Disk Drive
The hardware which spins the disk and has the heads and control circuitry for reading and writing
the data on the disk.
Diskette
A floppy disk in a hard housing with a shutter.
DMA
Direct Memory Access. Special circuitry for memory to memory transfer of data which do not require
CPU action.
DMI
Desktop Management Interface. A standard that provides PC management applications with a
common method of locally or remotely querying and configuring PC computer systems hardware
and software components, and peripherals.
DOS
Disk Operating System (MS-DOS is a Microsoft Disk Operating System).
Driver
A computer program which converts application and operating system commands to external devices
into the exact from required by a specific brand and model of device in order to produce the desired
results from that particular equipment.
ECP
Extended Capability Port. A set of standards for high speed data communication and interconnection
between electronic devices.
ESD
Electro-Static Discharge. The sudden discharge of electricity form a static charge which has built-up
slowly. Example: the shock you get from a doorknob on a dry day or the sparks you get form brushing
hair on a dry day.
89
SECTION 3
POST
Power On Self Test. A program which part of the BIOS which checks the configuration and operating
condition of your hardware whenever power is applied to your notebook. Status and error messages
may be displayed before the operating system is loaded. If the self test detects failures that are so
serious that operation can not continue, the operating system will not be loaded.
Extended Memory
All memory more than the 640KB recognized by MS-DOS as system memory.
FCC
Federal Communication Commission.
Floppy Disk
A spinning platter of magnetic data storage media which is highly flexible.
GB
Gigabyte.
Hard drive
A spinning platter of magnetic data storage media where the platter is very stiff.
Hexadecimal
A decimal notation for the value of a 4 bit binary number. (0-9, A, B, C, D, E, F) Example: 2F in
hexadecimal = 00101111 = 47 in decimal.
I/O
Input/Output. Data entering and leaving your notebook in electronic form.
I/O Port
The connector and associated control circuits for data entering and leaving your notebook in electronic
form.
IDE
Intelligent Drive Electronics. A type of control interface for a hard drive which is inside the hard drive
unit.
Infrared
Light just beyond the red portion of the visible light spectrum which is invisible to humans.
IR
An abbreviation for infrared.
IrDA
Infrared Data Association. An organization which produces standards for communication using infrared
as the carrier.
IRQ
Interrupt Request. An acronym for the hardware signal to the CPU that an external event has occurred
which needs to be processed.
KB
Kilobyte.
90
Program
An integrated set of coded commands to your computers telling your hardware what to do and how
and when to do it.
PS/2
An IBM series of personal computers which established a number of standards for connecting external
devices such as keyboards and monitors.
RAM
Random Access Memory. A hardware component of your notebook that holds binary information
(both program and data) as long as it has the proper power applied to it.
RAM Module
A printed circuit card with memory and associated circuitry which allows the user to add additional
memory to the computer without special tools.
SECTION 3
Reset
The act of reloading the operating system. A reset erases all information stored in RAM.
Restart
See Reset.
Resume
To proceed after interruption. In your notebook this refers to returning to active operation after having
been in one of the suspension states.
ROM
Read Only Memory. A form of memory in which information is stored by physically altering the
material. Data stored in this way can not be changed by your notebook and does not require power
to maintain it.
SDRAM
Synchronous Dynamic Random Access Memory.
Serial Port
A connection to another device through which data is transferred one bit at a time on a single wire
with any other wires only for control of the device not for transfer of data.
Shadow RAM
A technique of copying data or applications stored in ROM (Read Only Memory) into RAM (Random
Access Memory) for access during actual operation. RAM is much faster to access than ROM,
however ROM contents are not lost when power is removed. Shadowing allows permanently stored
information to be rapidly accessed.
91
SMART
Self-Monitoring, Analysis and Reporting Technology (SMART) is an emerging technology that provides
near-term failure predictions for hard drives. When SMART is enabled the hard drive monitors
predetermined drive attributes that are susceptible to degradation over time. If a failure is likely to
occur. SMART makes a status report available so that the LifeBook can prompt the user to back up
the data on the drive. Naturally not all failures are predictable. SMART predictability is limited to
those attributes which the drive can self-monitor. In those cases where SMART can give advance
warning, a considerable amount of precious data can be saved.
SRAM
Static random access memory. A specific technology of making RAM which does not require periodic
data refreshing.
Status Indicator
A display which reports the condition of some portion of your hardware. On your notebook this is an
LCD screen just above the keyboard.
Stereo (audio)
A system using two channels to process sound from two different sources.
Stroke (keyboard)
The amount of travel of a key when it is pressed from resting to fully depressed.
Suspend
To make inoperative for a period of time. Your notebook uses various suspension states to reduce
power consumption and prolong the charge of your battery.
SVGA
Super VGA.
S-Video
Super Video. A component video system for driving a TV or computer monitor.
System Clock
An oscillator of fixed precise frequency which synchronizes the operation of the system and is
counted to provide time of day and date.
TFT
Thin Film Transistor - A technology for flat display panels which uses a thin film matrix of transistors
to control each pixel of the display screen individually.
UL
Underwriters Laboratories - An independent organization that tests and certifies the electrical safety
of devices.
VGA
Video Graphics Array. A video display standard originally introduced by IBM with the PS/2 series of
personal computers.
92
VRAM
Video Random Access Memory. A memory dedicated to video display data and control.
WFM
Wired for Management is Intel’s broad-based initiative to reduce the total cost of ownership (TCO) of
business computing without sacrificing power and flexibility.
Write Protect
Prevent alteration of the binary state of all bits in a storage media. Example: all information on a
device such as a floppy diskette; a block of space in a storage media such as partition of a hard
drive; a file or directory of floppy diskette or hard drive.
Zip Drive
A 100MB read/rite removable media disk drive.
Zoomed Video
A PC Card port which allows notebook PCs to deliver full screen broadcast quality video through
third party PC Cards, including TV tuners, video capture, and MPEG full-motion video.
93
SECTION 3
XGA
Extended VGA.
">