Imagine Communications BNP 2xr+ Broadcast Network Processor Installation Guide

PDF

ஆவணம்

விளம்பரம்

Installation Guide

Selenio

BNP2xr+ Installation

Guide

January-2016

Revision A

Selenio TM BNP 2xr Installation Guide, 

Document part number: 250-0379-01 Rev. A

Printed 2/20/16

Publication Information

This material is protected by the copyright laws of the United States and other countries. No part of this document may be reproduced, distributed, or altered in any form, by any means, by any entity nor may it be used to make any derivative work

(such as translation, transformation, or adaptation) except in accordance with applicable agreements, contracts, or licensing, without the express written consent of Imagine Communications. All other uses are illegal.

Notice

This publication is designed to assist in the use of the product as it exists on the date of publication of this manual, and may not reflect the product at the current time or an unknown time in the future. This publication does not in any way warrant description accuracy or guarantee the use for the product to which it refers. Imagine Communications reserves the right, without notice to make such changes in equipment, design, specifications, components, or documentation as progress may warrant to improve the performance of the product.

Trademarks

Selenio TM and Telurio TM are trademarks of Imagine Communications. Microsoft® and Windows® are registered trademarks of Microsoft Corporation. All other trademarks and trade names are the property of their respective companies.

Patents

The products described herein are covered by one or more U.S. and foreign patents pending.

U.S. Patents: 6,996,129; 7,046,677; 7,818,355; 8,180,920. Other US and foreign patents pending.

Contact Information

Imagine Communications has office locations around the world. For domestic and international location and contact information see: http://www.imaginecommunications.com/contact-us/

Support Contact Information

For domestic and international support of Selenio VMG, Selenio BNP, Selenio SEP, Selenio MMC, Selenio TAT, Telurio

Packager, Telurio Recording Manager, and Telurio BNP products, contact:

Support Contacts: http://app.imaginecommunications.com/customercommunity

1.866.4.Imagine // (1.866.446.2446) - Inside North America

+1.44.208.339.1900 - Europe & Africa

+971.4.433.8260 - Middle East

+852.2776.0628 - Asia

For domestic and international support of all other Imagine Communications' products not mentioned above, contact:

Support Contacts: http://www.imaginecommunications.com/services/technical-support/

Selenio TM BNP2xr+ Installation Guide 2

Document Change History

BNP 3xr Installation Guide document history

Part Number

250-0379-01 Rev A

230-0307-01 Rev A

Release Date

01/30/2016

11/20/2014

Document Changes

Re-brand for Imagine Communications.

New document for new BNP product.

Selenio TM BNP2xr+ Installation Guide 3

Publication Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Notice. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Patents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Support Contact Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Document Change History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Chapter 1: Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Document Organization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Document Audience . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Document Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Graphics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Chapter 2: Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

In This Chapter: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

BNPFront Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

LED Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Port Mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

BNP Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

BNP Internal Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Chapter 3: Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

In This Chapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Required Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Site Cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Electrostatic Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Rack Mounting the BNP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Installing the BNP into a Rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Grounding the BNP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Connecting the Chassis Ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Installing SFP Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Connecting AC Power to the BNP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Connecting AC power to a BNP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Connecting DC Power to the BNP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Connecting DC power to a BNP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Connecting External Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Installing the Compact Flash Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Chapter 4: Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

In This Chapter: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Selenio TM BNP 2xr+ Installation Guide 4

Table of Contents

LED Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Event Log Analysis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Contacting Customer Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Chapter 5: Field-replaceable Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

In This Chapter: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Replacing a Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Removing a Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Inserting a Power Supply. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Removing a GBP3 Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Replacing a GBP3 Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Replacing a Processor Module (PROC3) or an ASI Module . . . . . . . . . . . . . . . . . . . . . . . . 31

Removing a PROC3 or ASI Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Replacing a PROC3 or ASI Module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Chapter 6: Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

In This Chapter: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Input Interfaces/Output Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

MPEG Processing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Video Formats. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Audio Formats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Elementary Stream Types & Conversions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Digital Broadcast. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Regulatory Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Electrical/Mechanical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Environmental. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Appendix A: Localized Cautions and Warnings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Appendix B: Conformity and Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Declarations of Conformity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

United States. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Canada . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Europe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Japan. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Australia/New Zealand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Selenio TM BNP 2xr+ Installation Guide 5

CHAPTER 1

Introduction

The Selenio™ Broadcast Network Processor (BNP) products deliver the industry's highest density digital video solution for grooming, statistical multiplexing, transrating, digital program insertion (DPI). Based on its proprietary flexible, scalable and modular platform, the BNP simplifies and expedites deployments of advanced video services, simplifies operation and management, and reduces operational and capital costs.

Figure 1.

BNP 2xr+

Receiving input through its Gigabit Ethernet or ASI interfaces, the BNP can statistically multiplex while performing grooming and digital ad and overlay insertion.

The BNP can receive both standard definition (SD) and high definition (HD) program services, and can concurrently groom and insert digital ads within the same box.

The BNP is fully MPEG compliant and interoperable with leading cable industry equipment.

The BNP makes configuration more intuitive and simple by providing a Java-based graphical user interface that can be accessed through a standard Web browser. Configuration can be performed through SNMP using any standard network management application. The SNMP MIBs are readily available from the BNP home page.

This BNP 2xr+ Hardware and Installation Reference describes the BNP system hardware and provides guidelines for physical installation, initial configuration, and basic troubleshooting.

Document Organization

This guide is organized as follows:

•

Chapter 1, Introduction –

(this chapter) describes the contents and conventions used in the BNP

2xr+ Hardware and Installation Reference.

•

Chapter 2, Overview –

provides a hardware description of the BNP 2xr+ features and components.

• Chapter 3, Installation – describes the initial steps and requirements for installing the BNP 2xr+

• Chapter 4, Troubleshooting – provides information about LED indicators and component replacement.

• Chapter 5, Field-replaceable Units – lists the FRUs for the BNP 2xr+ and provides information about handling and replacements.

• Chapter 6, Specifications – includes information about regulatory, environmental, electrical, and mechanical compliances.

Selenio TM BNP 2xr+ Installation Guide 6

Document Audience

• Appendix A, Localized Cautions and Warnings – lists all of this guide’s Caution and Warning statements in French and German.

•

Appendix B, Conformity and Safety Information –

provides regulatory compliance information for the BNP.

• The glossary and index can be used to quickly reference information.

Document Audience

This guide is intended for system administrators who are responsible for installation and maintenance of the BNP 2xr+ at Telco and Cable Headends. Users of this guide should be familiar with general video and networking terminology and should be accustomed to basic network hardware installation.

Most importantly, the user must be familiar with the basics and principles of broadcast network processing.

Document Conventions

Table 1 provides an easy way to recognize information of particular importance in this manual

Table 1. Document Conventions

When you see: It means:

Notes point out information that may not be part of the text but provide tips and other helpful advice.

Cautions let you know that an action may have undesirable consequences if the instructions are not followed correctly. Cautions also indicate that failure to follow guidelines could cause damage to equipment or loss of data.

Les symboles " ATTENTION ", représentés par l'icône de gauche, indiquent qu'une action peut avoir des conséquences indésirables si les instructions ne sont pas suivies correctement.

Les symboles " ATTENTION " indiquent également que le fait de ne pas suivre les instructions peut causer des dommages à l'équipement ou résulter en une perte de données.

Das links abgebildete Symbol Vorsicht weist darauf hin, dass ein Vorgang unerwünschte Konsequenzen haben kann, falls die Anweisungen nicht korrekt befolgt werden.

Das Symbol Vorsicht weist außerdem darauf hin, dass Geräte beschädigt oder Daten verloren gehen können, wenn die Anweisungen nicht befolgt werden.

Warnings indicate that failure to take the necessary precautions or to follow guidelines could cause harm to equipment and personnel.

Les symboles " AVERTISSEMENT ", représentés par l'icône de gauche, indiquent que le fait de ne pas prendre les précautions nécessaires ou de ne pas suivre les instructions peut endommager l'équipement ou provoquer des blessures.

Das links abgebildete Symbol Warnung weist darauf hin, dass Geräte beschädigt oder

Personen verletzt werden können, wenn die notwendigen Vorsichtsmaßnahmen nicht eingehalten oder die Anweisungen nicht befolgt werden.

Graphics

In some cases the line art and screen-shots shown in this manual may differ slightly from what appears on the actual product.

All efforts have been made to ensure that the latest images are used. In all cases, the functionality described is current at the time of writing.

Selenio TM BNP 2xr+ Installation Guide 8

CHAPTER 2

Overview

This chapter describes the physical characteristics of the Selenio™ Broadcast Network Processor (BNP).

Before installing, configuring, or replacing any component of the BNP, please be sure that you understand the chassis and its components.

In This Chapter:

•

“BNPFront Panel,” nest.

•

“BNP Rear Panel” on page 11

•

“BNP Internal Components” on page 12 .

BNPFront Panel

Figure 2

shows the front view of the BNP with the bezel in place. When the front bezel is removed, the

RS-232 serial port is visible, as shown in

Figure 3

Figure 2.

Front panel (with bezel)

DTI Ports - Not Used

10/100 BaseT Ethernet Ports

GigE Ports 1-8 (SFP)

BNP2xr+

System LEDs

10 GigE Port (XFP) - Not Used

Compact Flash Card

Note: The 10 GigE (XFP) and DTI ports are currently not used.

Each BNP has eight GigE ports. These ports can be used for input and output (full-duplex) of video over

IP data streams. The ports, LEDs, and compact flash card are located on the Gigabit Ethernet Processor-

3 (GBP3) module on the front within the chassis enclosure.

For instructions on removing and replacing the GBP3 module, see

“Removing a GBP3 Module” on page 30

Note: The RS-232 serial port is used only by field service personnel. Under normal circumstances you will not need to access this port.

Selenio TM BNP 2xr+ Installation Guide 9

BNPFront Panel

Figure 3.

Front panel (without bezel)

Serial port

LED Indicators

The primary Light Emitting Diodes (LEDs) visible on the front of the BNP chassis are shown in Figure 4 .

These LEDs indicate the general health of the BNP.

Figure 4.

LEDs

Cfg/Pwr Fault Backup

GigE 1-8 Port Status

(SFPs)

Compact Flash 10/100 BaseT

Ethernet Port

Table 2 describes the patterns used by the LED indicators.

Table 2.

LED

CFG/PWR

Fault

Backup

LED indicators

Compact flash

GigE 1-8 a

Color

Off

Solid Green

Solid Red

Indication

No power to chassis

Power is OK

Chassis is powering up and configuration load is in progress

Solid Green

Blinking Green

System main process is in wrong state

System status is OK

Blinking Red/Orange Hardware fault or alarm

Solid Green Active or primary chassis

Solid Red/Orange

Blinking Green

Solid Green

Blinking Red

Solid Red

Solid Green

Standby chassis

FPGA configuration load in progress

Compact flash card is OK

Compact flash card not installed

Compact flash card error is present

SFP installed

Selenio TM BNP 2xr+ Installation Guide 10

BNP Rear Panel

Table 2. LED indicators (Continued)

LED

10/100 BaseT

AC/DC Power On

Indicator

(Rear Panel

Figure 6

)

On-Board DC

Power Status

( Figure 9 )

Color

Solid Green

Blinking Yellow

Solid Green

Off

Solid Green

Solid Yellow

Indication

Autonegotiated link status

Activity

AC/DC Power is on

No input AC/DC Power

On-board DC power OK

On-board DC power fault a. The compact flash card is necessary for BNP functionality.

Port Mapping

Figure 5

shows the SFP port location mapping scheme. These port numbers correspond with the port

LEDs described in “LED Indicators,”

above.

Figure 5.

Port mapping and LED indicators

Port number

2 4 6 8

1 3 5 7

1 2 3 4 5 6 7 8

Port LEDs

BNP Rear Panel

Figure 6

shows the rear view of the BNP with network processor (PROC3) cards and an ASI module installed.

Figure 6.

Rear panel

ASI Module Maximum 3 PROC3s per BNP 2xr+

GOOD

PWR

GOOD

LOCK

100-240V-8.8A,50/60 Hz

Selenio TM BNP 2xr+ Installation Guide 11

BNP Internal Components

Configuration Options for PROC3 Combinations

At least one PROC3 is required and may be combined with ASI modules to populate the four slots. Up to three PROC3 cards are allowed.

The right side of the chassis holds the power supply, including the power connector and fan. The power supply fan is not replaceable, except as part of the power supply. For details about replacing the

modules and power supply, see Chapter 5, “Field-replaceable Units.”

BNP Internal Components

The BNP consists of three main sections:

• One network interface module—called the Gigabit Ethernet Processor (GBP3) module.

• One to three PROC3 cards.

• The power supply assembly.

Selenio TM BNP 2xr+ Installation Guide 12

CHAPTER 3

Installation

This chapter provides the information necessary to install the Selenio™ Broadcast Network Processor

(BNP) into a rack. Read this entire chapter before beginning, and perform the installation in the order described.

After completing this physical installation, you can use guidelines from the System Configuration chapter of the BNP User Guide to perform the software configuration for your system.

In This Chapter

•

“Before You Begin,” next.

•

“Rack Mounting the BNP” on page 15

•

“Grounding the BNP” on page 16

•

“Installing SFP Modules” on page 17

•

“Connecting AC Power to the BNP” on page 18

•

“Connecting DC Power to the BNP” on page 19 .

•

“Connecting External Ports” on page 22

•

“Installing the Compact Flash Card” on page 22 .

Before You Begin

The BNP ships fully assembled, with cables and packaging appropriate for your installation. At the installation site, you must provide some additional tools and materials to complete the installation as described in this chapter.

Topics in this section:

•

“Required Equipment,”

next.

•

“Site Cabling” on page 14

•

“Electrostatic Precautions” on page 14 .

Required Equipment

Be sure that you have the required items listed below before you begin the installation of the BNP. You will need:

• Populated BNP chassis, including:

1 GBP3 module

Up to three PROC3 modules

Selenio TM BNP 2xr+ Installation Guide 13

Before You Begin

AC or DC Power Supply

ASI modules, if ordered

• Compact flash card

• AC power cord, included

• DC connector cables, if DC power supply is used

• Front and rear rack mount brackets, included

• Rack mount bracket screws, included

• Two (2) M4 grounding nuts, included

• Eight (8) rack mount screws, not included

• Phillips and slotted screwdrivers, not included

• 1 ring lug for grounding, included

• Ethernet cable long enough to directly connect the BNP and the management workstation, not included

Site Cabling

Note: The BNP is intended for local (intra-building) connections only and is not designed or evaluated for direct connections to the public telecommunications/cable distribution system. Cable and

Ethernet connections should be made in accordance with the National Electrical Code (NEC).

As a preliminary measure, you should ensure that at least one of the following conditions are met:

• Cable runs are located in the same building as this unit;

• Any copper cables that run through air between buildings are less than 42m (140ft);

• Cable runs between buildings are in underground conduit, where a continuous metallic cable shield or a continuous metallic conduit containing the cable is bonded to each building grounding electrode system.

Electrostatic Precautions

Warning!

Whenever computer components are handled (especially during installation), the equipment can be damaged by the buildup of static electricity. Take precautions before touching any internal components or boards by wearing an ESD wrist strap or working on an antistatic mat. Always hold system modules by the edges and avoid touching any electronic circuitry on the cards.

Caution:

See also “Handling Computer Components” on page 44 and

“Electrostatic Advisory” on page 44 for the localized version of the above advisories.

Selenio TM BNP 2xr+ Installation Guide 14

Rack Mounting the BNP

Rack Mounting the BNP

Caution: Please install the BNP so as to be easily accessible and as close to a power socket outlet as possible.

See also “Power Socket Proximity” on page 45 for the localized version of the above caution.

The BNP requires 1RU of space and is mounted into a standard 19-inch rack using rack mount brackets for both the front and rear of the system.

When choosing the location for the BNP within a rack, make sure that the BNP will be placed within the rack evenly, and that the installation will not cause uneven mechanical loading and weight distribution.

Do not mount the BNP into any rack that obstructs clean air flow either in the front or the rear.

Generally, an aisle of at least 15 inches is the minimum distance to ensure proper air flow.

Caution: Install this equipment only in an operations site that is humidity- and temperaturecontrolled, to ensure compliance with requirements for ambient operational conditions specified in

Table 3 and

Table 15, “Environmental Ranges,” on page 43 .

See also “Operations Environment” on page 45 for the localized version of the above caution.

Table 3. Environmental Requirements

Condition

Storage Temperature

Ambient Operating

Temperature

Ambient Humidity

Limits

-40° to 70° C (-40° to 158° F)

0° to 50° C (32° to 122° F)

5% to 95% (non-condensing)

Installing the BNP into a Rack

Use steps in this section to position and secure the BNP into the operations rack.

Using the provided screws, attach the front rack mount bracket to one side of the chassis, and repeat on the other side of the chassis.

Selenio TM BNP 2xr+ Installation Guide 15

Grounding the BNP

Install the chassis rear rack shelf to the rear mounting rails of the rack, using two screws on each side

Secure shelf to rear rails

Install the BNP chassis in the rack.

The rear edge of the chassis will rest on the rear rack shelf.

Secure the front of the chassis to the rack, using two screws on each side.

Two screws  on each side

Grounding the BNP

Warning!

The BNP must be properly grounded to ensure safe operation. Before you connect power or turn on the BNP, ground the chassis. This section provides one method of grounding. There may be others: check your network configuration for details.

See also “Grounding Equipment” on page 42 for the localized version of the above warning.

Note: For an AC BNP, and if power is to be derived from a rack-mounted AC power strip, ensure that the power strip is properly grounded to the rack and UL compliant for 12 AWG.

Selenio TM BNP 2xr+ Installation Guide 16

Installing SFP Modules

Connecting the Chassis Ground

Using a length of wire, terminate one end with a ring lug.

For use with a DC power supply, the grounding wire must be a minimum of 12 AWG.

Using the provided M4 nut, install the ring lug on the grounding terminal.

The grounding terminal is at the rear of the BNP chassis, located at the lower left of the power supply, just beneath the power supply handle (

Figure 7

Figure 7.

Grounding Terminals

GOOD

PWR

GOOD

LOCK

Grounding terminal (AC power supply)

INPUT

PWR

100-240V-8.8A,50/60 Hz

LOCK

+ +

Input 48V DC 22A

Grounding terminal (DC power supply)

Using wire strippers, strip off 3/8 inch of insulation from the other end of the wire.

Attach the stripped wire into a grounding hole on the equipment rack.

Installing SFP Modules

For optical output, Small Form Factor 1Gbps (SFP) transceivers comply with the current SFP Multi-

Source Agreement (MSA) Specification.

• GigE interfaces that meet 1000 Base SX specifications support 850 nm wavelengths for distances up to 550 meters.

• GigE interfaces that meet 1000 Base LX specifications support 1310 nm and 1550 nm wavelengths for distances up to 70 kilometers.

SFPs approved for use with the BNP are based on the Multi-Source Agreement (MSA) and listed in

Table 4 :

Table 4. Supported SFPs

Manufacturer

Finisar

Fiberdyne

Avago

Part Number

FTLF1519P1BCL

FCMJ-8521-3

FGE-SFP-T

ABCU-5710RZ

Description

SFP 1550nm GigE optical module

1000BaseT Copper SFP Transceiver

SFP 1550nm GigE optical module

Note: For updates on the latest SFPs and XFPs approved for use with products from Imagine

Communications, log in to the Imagine Communications website and search for the following terms: 



Selenio TM BNP 2xr+ Installation Guide 17

Connecting AC Power to the BNP

SFP

-or

XFP

To install an SFP, follow the manufacturer’s instructions. General guidelines to SFP installation include:

Consider your network and cabling requirements and verify that the SFP you are installing is an

approved model as described in Table 4 .

Insert the SFP into the port.

SFPs are keyed so they can only be installed one way.

Slide the SFP into the port until it clicks into place and the LED is activated.

Connecting AC Power to the BNP

Once installed in a rack, you can connect power to the chassis, either from a wall source or a rackmounted AC power strip. However, before you connect power to the chassis, make sure that the circuit, wiring, and connections that you are using to supply the power will not become overloaded by the

BNP(s). For power consumption details, see “Specifications” on page 35 .

Caution: The BNP does not have an on/off power switch. Connection to the power source powers up the BNP immediately.

See also “Equipment On and Off” on page 42 for the localized version of the above caution.

Refer also to the System Shutdown section of your BNP Element Manger User Guide to find out how to properly power off and shut down an operational BNP.

Caution: If the BNP is to be connected to a rack-mounted, properly grounded AC power strip, ensure that the strip is compliant with 12AWG UL Certification.

See also “AC Power Strip Compliance Advisory” on page 41 for the localized version of the above caution.

Note: Before you connect power, check to ensure that all applicable ports are cabled, and all installed modules are properly seated in their slots.

Connecting AC power to a BNP

Locate the AC power cable included with the BNP chassis.

Plug one end of the power cable into the BNP power connector. (

Figure 8

)

Figure 8.

AC Power Supply

Power supply LEDs

GOOD

PWR

GOOD

LOCK

Power connector

100-240V-8.8A,50/60 Hz

Selenio TM BNP 2xr+ Installation Guide 18

Connecting DC Power to the BNP

Plug the other end of the power cable into the input power source.

The BNP should now be powered up. Check the LEDs to verify that power has been applied. The

Cfg/Pwr LED and the PSU1 and PSU2 LEDs should now be solid green.

See also “LED Indicators” on page 10 .

Connecting DC Power to the BNP

This section contains DC power safety advisories and installation procedures in the following topics:

•

“Safety,”

next.

•

“Preparation” on page 19 .

•

“Connecting DC power to a BNP” on page 20 .

Safety

Caution: Only trained personnel should install or replace this equipment.

See also “Qualified Personnel” on page 42 for the localized version of the above caution.

• Remove all jewelry, including rings, necklaces, and watches. Metal objects will heat up when connected to power and ground, and can cause serious injury or weld the metal object to the terminals.

• The protective earth connection should be connected before proceeding with the power connection.

• The power cables should be attached to the breaker.

• Confirm that the DC power source is powered off during installation.

• For a centralized DC power connection, the unit must be installed in a restricted access location in accordance with Articles 110-16, 110-17, and 110-18 of the National Electrical Code, 

ANSI / NFPA 70.

• Damage may occur if the power is connected improperly.

Preparation

Caution: Make sure that the safety screw is in the locked position (turned counterclockwise) after the

power supply is installed, but before connecting power ( Figure 10 ). Note that the locked

position may be different than that of similar units. This ensures that the power supply cannot be accidentally disconnected, causing possible damage.

See also “Safety Screw Lock Advisory” on page 43 for the localized version of the above caution.

Once installed in a rack, connect power to the chassis. However, before you connect power to the chassis, make sure that the circuit, wiring, and connections that you are using to supply the power will not become overloaded by the BNP(s). See “Specifications” on page 35 for power consumption details.

Selenio TM BNP 2xr+ Installation Guide 19

Connecting DC Power to the BNP

Note: The BNP does not have an on/off power switch. Connection to the DC external power source is necessary to power up the system. Please see the System Shutdown section of your BNP Element

Manager User Guide to find out how to properly power off and shut down an operational BNP.

Caution: These are +48V DC power supplies, not -48V. Please connect accordingly.

See also “+48V DC Power Supply Advisory” on page 43 for the localized version of the above caution.

The two inputs to the DC power supply are +48V inputs.

• If you need to set up redundant inputs, connect the inputs to the DC power supply from two different 48V sources. When both 48V inputs are sourced, the power supply will load share across the inputs, each of the inputs drawing half the total power. When one 48V input source fails, the other 48V input will draw the full power.

• If you choose not to have redundant inputs, connect only one of the two inputs to the DC power supply and leave the other disconnected.

The DC power supply is configured so that the black (top) cable connects to a -48VDC input and the red (bottom) cable connects to positive ground. Before connecting any cables, measure the output to make sure that you are connecting a -48VDC input to the black cable of the power supply.

Note: Before you connect power, check to ensure that all applicable ports are cabled, and all installed modules are properly seated in their slots.

Connecting DC power to a BNP

Cut the provided DC connector cables to the correct length to reach the BNP from the power source.

Attach the connector cables from the power source to the BNPpower connectors (

Figure 9

for

connector locations, and Figure 10 for connection result).

Figure 9.

DC Power Supply

INPUT

PWR

LOCK

Power supply LEDs

Power connectors, -48VDC (for black)

Power connectors, positive (for red)

+ +

Input 48V DC 22A

Selenio TM BNP 2xr+ Installation Guide 20

Connecting DC Power to the BNP

Figure 10.

DC Power Supply Connectivity

Lock the safety screw

Power connector cables

Two cables for 48VDC

Two cables for ground

Connect -48VDC input to b

Connect positive ground to red

Attach the other end of the power connector cables into the input power source (

Figure 11 ).

The power cables should be attached to an external UL Listed 20 amp circuit breaker.

Figure 11.

DC Power Cable Connectivity

Connect to the

DC power source

Apply power to the BNP.

Note: The BNP does not have an on/off power switch. To apply power for the DC system, toggle the external circuit breaker to the ON position.

The BNP should now be powered up. Check the LEDs to verify that power has been applied. The

Cfg/Pwr LED and the PSU1 and PSU2 LEDs should now be solid green. See also “LED Indicators” on page 10 .

Selenio TM BNP 2xr+ Installation Guide 21

Connecting External Ports

Connecting External Ports

The BNP chassis has three discrete types of ports. When connecting ports, be sure to use the correct cabling. This section describes the port types and basic cabling, but the actual cabling requirements will depend on your specific network configuration and needs.

Fast Ethernet Management Port 10/100-0

The 10/100BaseT (10/100-0) Ethernet port is used to communicate unencrypted with an external console for SNMP configuration control, maintenance diagnostics, status monitoring, fault notification, and redundancy switching. The external console can be a workstation on the IP network.

Fast Ethernet Management Port 10/100-1

The 10/100BaseT (10/100-1) Ethernet port is used to communicate with an external console for SNMP configuration control, maintenance diagnostics, status monitoring, fault notification, and redundancy switching. The external console can be a workstation on the IP network.

GigE Port

The Ethernet port must be fitted with small-form-factor pluggables (SFPs). See Table 4

for a list of tested and approved SFPs that can be used with the BNP.

ASI Port

The number of ASI ports in your BNP chassis depends on the number of ASI cards that are installed. Up to three ASI cards can be installed, each with six ports.

Installing the Compact Flash Card

The BNP uses a compact flash card to load software and save configuration information. You cannot use your BNP without it.

If the compact flash card was not shipped pre-installed with your BNP, you must install it. Remove the flash card from the shipping container and install it into the compact flash slot located on the front of the BNP chassis.

If your compact flash card fails, contact technical support for details about flash repair or replacement.

See

page 24

for details on contacting technical support.

Caution: Your license is attached to the compact flash (CF); do not discard it. Even if a CF card fails, keep the device and contact Imagine Communications technical support for instructions on repair or obtaining a working replacement.

See also “Compact Flash Advisory” on page 43 for the localized version of the above caution.

Selenio TM BNP 2xr+ Installation Guide 22

CHAPTER 4

Troubleshooting

This chapter guides you through basic troubleshooting and points to resources you can use with you

Selenio™ Broadcast Network Processor (BNP).

In This Chapter:

•

“LED Indicators,” next.

•

“Event Log Analysis” on page 24

•

“Contacting Customer Support” on page 24 .

LED Indicators

The LED indicators are described in

“LED Indicators” on page 10

. These should be your first line of inquiry if any BNP component is not performing correctly.

Figure 12.

LED Indicator Locations

Cfg/Pwr Fault Backup

GigE 1-8 Port Status

(SFPs)

Compact Flash 10/100 BaseT

Ethernet Port

Table 5. LED Indications

Indication

An LED indicator for one of the GigE ports is off.

The LED indicator for the 10/100 BaseT port is off.

The system power LED indicator is off.

Possible Solution

Verify that the module is installed correctly and has power.

Verify that the module is installed correctly and the

10/100 BaseT port cable is connected correctly.

Verify that the power cord is correctly installed and that the power is turned on.

Selenio TM BNP 2xr+ Installation Guide 23

Event Log Analysis

Table 5. LED Indications (Continued)

Indication

The LED indicator for the compact flash is blinking red

The LED indicator for the compact flash is solid red.

Possible Solution

Install a compact flash card.

A flash error has occurred or the flash module is corrupted and needs to be reformatted or replaced.

Event Log Analysis

If asked to do so by technical support, access the event log. You will be instructed on this procedure by the technical support engineer.

Contacting Customer Support

Imagine Communications Customer Support is available 24x7. If, after reviewing this chapter, you require assistance please contact Imagine Communications Customer Support via any of the following methods:

Table 6. Contacting Imagine Communications Customer Support

Method

Internet

Inside North America

Europe and Africa

Middle East

Asia

Contact Information http://app.imaginecommunications.com/customercommunity

1.866.4.Imagine // (1.866.446.2446)

+1.44.208.339.1900

+971.4.433.8260

+852.2776.0628

Selenio TM BNP 2xr+ Installation Guide 24

CHAPTER 5

Field-replaceable Units

This chapter provides information to assist you with replacement of Field-replaceable Units (FRUs) at the Selenio™ Broadcast Network Processor (BNP) . The chassis does not need to be removed from the rack to replace a FRU, but the system must be powered down before beginning any replacement process.

If replaced items need to be configured, see the System Configuration chapter in your BNP User Guide.

Note: The BNP must be shut down/powered off prior to removal of the Network Processor Module, ASI

Module, or GBP3 Module. See “System Shutdown” on page 34 for more information. 



It is not necessary to shut down nor power off the system when servicing hot-swappable modules.

Warning!

Never replace any FRU while the chassis is still connected to the power source.

See also “Power Source Safety Advisory” on page 48 for the localized version of the above warning.

Warning!

Do not replace any component (such as fuses) not specifically described here. For replacement beyond the FRU level, contact your technical support representative for

instructions on returning the component. See “Contacting Customer Support” on page 24 .

See also “FRU Replacement Advisory” on page 48 for the localized version of the above warning.

Warning: Whenever computer components are handled (especially during installation), the equipment can be damaged by the buildup of static electricity. Take precautions before touching any internal components or boards by wearing an ESD wrist strap or working on an antistatic mat. Always hold system modules by the edges and avoid touching any electronic circuitry on the cards.

Caution!

See also “Handling Computer Components” on page 44 and

“Electrostatic Advisory” on page 44 for the localized version of the above advisories.

Selenio TM BNP 2xr+ Installation Guide 25

In This Chapter:

•

“Overview,” next.

•

“Replacing a Power Supply” on page 27 .

•

“Removing a GBP3 Module” on page 30

•

“Replacing a Processor Module (PROC3) or an ASI Module” on page 31

Overview

The four replaceable units on the BNP are shown in Figure 13 . The removal and replacement procedure

is provided for each.

Figure 13.

Top view of chassis, with FRUs visible

Power supply

GBP3 module

PROC3 Modules

The GBP3 module is located underneath the fan trays; its design is shown below in

Figure 14

Selenio TM BNP 2xr+ Installation Guide 26

Replacing a Power Supply

Figure 14.

Gigabit Processor - 3 Module

Replacing a Power Supply

The power supplies are located at the rear of the BNP chassis. Any time that the chassis is not receiving adequate power, as indicated by the system LEDs and performance, verify that power is reaching the chassis.

If power is reaching the power supply but not getting to the system, you might need to replace one or both power supplies.

Note: The BNP operates normally with just one power supply.

Removing a Power Supply

The basic procedure for removing a power supply is similar regardless of whether the power supply is for AC or DC power.

To remove a failed power supply:

Ensure that you have a replacement power supply ready to reinsert.

Ensure that there is no power to the unit:

• AC power supply units - Shut down the unit by removing the power cable from the power supply connector.

• DC power supply units - Toggle the circuit breaker to the OFF position. Disconnect the cables from the power connector.

Loosen the power supply unit by turning the safety screw clockwise.

Note: Turning the screw counterclockwise tightens the screw. Use a slotted screwdriver to tighten or loosen the screw, then use your fingers to further turn the screw, if necessary.

Firmly grasp the power supply by the handle, shown in Figure 15 (AC Power Supply) and Figure 16

(DC Power Supply).

Selenio TM BNP 2xr+ Installation Guide 27

Replacing a Power Supply

Figure 15.

Power supply handle (AC power supply)

Power supply insertion/ removal handle

Safety screw

Power connector

Figure 16.

Power supply handle (DC power supply)

Power supply insertion/ removal handle

Safety screw

Power connector

Disconnect cables from power connector

Pull gently but firmly, sliding the power supply out of the bay as shown in Figure 17 .

Figure 17.

Power supply removal

AC POWER SUPPLY

Rear of Chassis

DC POWER SUPPLY

Rear of Chassis

Selenio TM BNP 2xr+ Installation Guide 28

Replacing a Power Supply

Inserting a Power Supply

Once you have removed the failed power supply, install a replacement:

Remove the replacement power supply from its packing and carefully inspect it for damage.

Do not install a visibly damaged power supply.

Slide the replacement power supply into the slot

Figure 18.

Power supply insertion

AC POWER SUPPLY

Rear of Chassis

DC POWER SUPPLY

Rear of Chassis

Turn the screw counterclockwise to tighten it, securing the power supply to the BNP chassis.

Connect power to the power supply:

•

For AC power supplies, refer to “Connecting AC Power to the BNP” on page 18

• For DC power supplies, refer to

“Connecting DC Power to the BNP” on page 19 .

Selenio TM BNP 2xr+ Installation Guide 29

Removing a GBP3 Module

Ensure that you have a replacement module available, then shut down the unit by removing the power cable from the power supply connector.

Remove all cabling from the module.

Grasping it firmly with your fingers, gently remove the bezel on the front of the chassis (

Figure 19

Figure 19.

Front bezel removal

Front of Chassis

Using a Phillips screwdriver, loosen—but do not remove—the screws that secure both sides of the

GBP3 module to the chassis. They act as handles to assist with the module’s removal.

Figure 20.

Loosen the GBP3 module release screws

Loosen the release screws

Firmly grasping the screws, slide the GBP3 module out of the bay, as shown in Figure 21 .

Figure 21.

GBP3 module removal

Front of Chassis

Selenio TM BNP 2xr+ Installation Guide 30

Replacing a Processor Module (PROC3) or an ASI Module

Replacing a GBP3 Module

After you have removed the failed GBP3 module, replace it with the new one:

Grasp the module firmly by the edges only and slide it into the chassis, using the plastic guide rails to ensure proper seating.

Push until the module is firmly seated.

Using a Phillips screwdriver, tighten the insertion/removal screws to secure the GBP3 module to the

BNP chassis.

Replace the front bezel by snapping it in place.

Restore any cabling and power up the unit.

Replacing a Processor Module (PROC3) or an ASI

Module

Note: The BNP supports both ASI and ASI2 modules.

Removing and replacing either a PROC3 module or an ASI module uses the same procedure.

• If you are adding a new PROC3 or ASI module to an existing but underpopulated chassis, insert the card into the next designated slot.

• If you are replacing a failed unit, simply replace that unit regardless of the slot it occupies.

Removing a PROC3 or ASI Module

Use the Element Manager to perform the following tasks:

Delete all input and output groomings associated with the ASI module to be removed.

Delete all output programs and output TSs associated with the ASI module to be removed.

Shut down the unit by removing the power cable from the power supply connector.

Using a Phillips screwdriver, loosen—but do not remove—the insertion/removal screws, shown in

Figure 22

Selenio TM BNP 2xr+ Installation Guide 31

Replacing a Processor Module (PROC3) or an ASI Module

Figure 22.

Loosen the insertion/removal screws

Loosen the screws

Using the handles on either side of the module as a grip, gently but firmly slide the module out of the chassis, as shown in

Figure 23 .

Figure 23.

Remove the module

Rear of Chassis

Replacing a PROC3 or ASI Module

After a PROC3 module has been removed, replace it as soon as possible, or install a blank slot cover to ensure proper air flow. If you are leaving an empty slot, any empty slot should be fitted with a blank cover.

Caution: ASI modules should always be replaced; no filler should be used.

See also “ASI Module Replacement Advisory” on page 49 for the localized version of the above caution.

To install a PROC3 or ASI module:

Firmly hold the card by the edges or the handles and slide it into the chassis, using the plastic guide rails to ensure proper seating.

Press firmly until the module seats in the chassis.

Selenio TM BNP 2xr+ Installation Guide 32

Replacing a Processor Module (PROC3) or an ASI Module

Figure 24.

Install the ASI or PROC3 module (ASI shown)

Rear of Chassis

Using a Phillips screwdriver, tighten the insertion/removal screws to attach the card to the chassis.

Restore any cabling and power up the unit.

Reboot the BNP.

Selenio TM BNP 2xr+ Installation Guide 33

CHAPTER 6

Specifications

This chapter provides the system specifications for the Selenio™ Broadcast Network Processor (BNP).

In This Chapter:

•

“Input Interfaces/Output Interfaces,”

next.

•

“MPEG Processing” on page 35 .

•

“Video Formats” on page 35 .

•

“Audio Formats” on page 36 .

•

“Regulatory Compliance” on page 37 .

•

“Electrical/Mechanical” on page 37 .

•

“Environmental” on page 38

Input Interfaces/Output Interfaces

Table 7. Input/Output Interfaces

Interface

Gigabit Ethernet

Fast Ethernet

ASI

Type

8 SFP interfaces (copper or optical) configured

2 10/100BaseT control and management interface

Up to 18 ASI ports per chassis

Up to 3 ASI modules with 6 ASI ports each

Software configurable as input or output

213 Mbps data rate/port

Selenio TM BNP 2xr+ Installation Guide 34

MPEG Processing

MPEG Processing

Table 8.

MPEG

Transrating

MPEG Processing

Multiplexing and Table

Processing

DPI

Jitter Tolerance

Supported Format

SD and HD MPEG-2 video streams

VBR and CBR support

QoS - Ability to set priority for the level of transrating desired

MPEG-2 and MPEG-4 H.264/AVC multiplexing and re-multiplexing

MPTS, SPTS, multicast and unicast support

CBR and VBR support

PID filtering and remapping

PCR restamping and de-jitter

Generation and pass-through of PSIP tables

PAT and PMT generation

Seamless SD and HD splicing

SCTE 30 (DVS-380, DVS-638) and SCTE 35 compliant

SCTE 30 to SCTE 35 conversion

Text and graphical crawl messages and graphical logo overlays

SCTE 18 (Emergency Alert Message for cable)

SCTE 21 to SCTE 20 conversion

+/- 100 ms

Video Formats

Table 9.

Video

Video Formats

MPEG Profile and Level

All SD and HD resolutions

Frame Rates

Supported Format

MPEG-2 MP@ML (SD) and MP@HL (HD)

MPEG-4 H.264/AVC (all profiles supported)

SD – 720 x 576, 720 x 480, 704 x 480, 544 x 480, 528 x 480, 352 x 480

HD – 1080i x 1920, 1080i x 1440, 1080i x 1280, 720p x 1280,

480p x 720, 480p x 704, 480p x 640

24, 25, 29.97, 30, 50, 59.94, 60

Selenio TM BNP 2xr+ Installation Guide 35

Audio Formats

Audio Formats

Table 10. Audio Formats

Audio

Audio Format

Supported Format

Dolby AC-3, MPEG-1 Layer 2 (Musicam) and MPEG-2, MPEG-2 AAC,

MPEG-4 HE-AAC

Elementary Stream Types & Conversions

Table 11. Elementary Stream Types & Conversions

Output Transport

Stream (TS) Type

MPEG2

ATSC

SCTE

DVB

Video a

MPEG2 video (0x2)

Converts to 0x2 if input video has type 0x80.

H.264 (0x1B)

MPEG2 video (0x2)

SCTE video (0x80)

H.264 (0x1B)

SCTE video (0x80) 

Converts to 0x80 if input video has type 0x2.

H.264 (0x1B)

MPEG2 video (0x2)

Converts to 0x2 if input video has type 0x80.

H.264 (0x1B)

Audio b

MPEG1 audio (0x3)

MPEG2 audio (0x4)

ATSC AC-audio (0x81)

DVB AC-3 audio (0x6)

AAC (0x0f)

HE-AAC (0x11)

MPEG1 audio (0x3)

MPEG2 audio (0x4)

ATSC AC-audio (0x81)

Converts to 0x81 if input AC-3 audio has type 0x6.

AAC (0x0f)

HE-AAC (0x11)

MPEG1 audio (0x3)

MPEG2 audio (0x4)

ATSC AC-audio (0x81)

Converts to 0x81 if input AC-3 audio has type 0x6.

AAC (0x0f)

HE-AAC (0x11)

MPEG1 audio (0x3)

MPEG2 audio (0x4)

DVB AC-3 audio (0x6)

Converts to 0x6 if input AC-3 audio has type 0x81.

AAC (0x0f)

HE-AAC (0x11) a. For H.264 video, the stream type will be passed through regardless of input or output TS type.

Data

0x5 ~ 0xff

Selenio TM BNP 2xr+ Installation Guide 36

Digital Broadcast b. For AAC and HE-AAC audio, the stream type will be passed through regardless of input or output TS type.

Digital Broadcast

Table 12. Digital Broadcast

DVB

Digital Broadcast

Supported Format

ATSC PSIP, (A/52B, A/53E, A/58, A/65)

DVB (DVB-SI, DVB-SUB, DVB-TXT, CSA and Simulcrypt)

Regulatory Compliance

Table 13. Regulatory Compliance

Regulatory Type

Safety

Electromagnetics

Hazardous Substances

Compliance

UL 60950-1:2007; CAN/CSA-C22.2 No. 60950-1-07; TUV/GS, cTUVus:

IEC 60950-1:2005, EN 60950-1:2006+ A11

FCC - Title 47 CFR Part 15 Subpart B; Canada ICES-003, Issue 2, April

1995

RoHS-compliant (Restricted use of Hazardous Substances)

Electrical/Mechanical

Table 14. Electrical and Mechanical

Specification

Maximum Input Power

Limits

Line Frequency

Power consumption

Dimensions

Weight

Cooling

Limits

AC: 100-240V; 8.8A; 50/60Hz; Class 1

DC: 36-72V;15.7A; Class 1

50-60 Hz

400 W maximum, fully loaded chassis at 110 V AC

2RU (3.5˝ H x 19˝ W x 23.25˝ L) (88 H x 444 W x 590.4 L mm)

38.7 lbs. (17.6 kg)

Front to back; BTU: 2900 BTU/hour maximum

Selenio TM BNP 2xr+ Installation Guide 37

Environmental

Table 15. Environmental Ranges

Condition

Storage Temperature

Ambient Operating

Temperature

Ambient Humidity

Noise Emissions

(In accordance with ISO

9296)

Value Range

-40° C to 70° C (-104° F to 158° F)

0° to 50° C (32° to 122° F)

5% to 95% (non-condensing)

LWAd (iB=10dB) 7.2 B 6.9 B

LpAm (TBD) 58.1 dBA 55.3 dBA

Environmental

Selenio TM BNP 2xr+ Installation Guide 38

APPENDIX A

Localized Cautions and Warnings

The warning and caution statements used in this manual are translated—in this appendix—into equivalent French and German annotations.

Handling Computer Components

Page number Statement type

Page 14

Warning

Avertissement

Warnung

Statement

Lors de la manipulation de composants électroniques ou informatiques (en particulier pendant l'installation) l'équipement peut être endommagé par l'accumulation d'électricité statique.

Prenez des précautions avant de toucher tout circuit ou toute carte interne, soit en portant un bracelet antistatique, soit en travaillant sur un tapis de sol antistatique.

Tenez toujours les modules du système par leurs bords et

évitez de toucher tout circuit électronique sur les cartes.

Bei der Handhabung von Computerbauteilen (insbesondere beim Einbau) können diese durch elektrostatische Aufladung beschädigt werden. Treffen Sie Vorsichtsmaßnahmen, indem

Sie ein Erdungsarmband anlegen oder auf einer antistatischen

Matte arbeiten, bevor Sie Bauteile oder Leiterplatten im

Inneren des Geräts berühren. Halten Sie Systemmodule immer an den Kanten, und berühren Sie die elektronischen Bauteile auf den Leiterplatten nicht.

Electrostatic Advisory

Page number Statement type

Page 14 Caution

Statement

Attention

Vorsicht

EQUIPEMENT SENSIBLE A L'ELECTRICITE STATIQUE

PRENEZ DES PRECAUTIONS

Elektrostatisch empfindliches Gerät

Vorsichtsmaßnahmen beachten

Selenio TM BNP 2xr+ Installation Guide 39

Power Socket Proximity

Page number Statement type

Page 15

Caution

Attention

Vorsicht

Statement

Please install the BNP so as to be easily accessible and as close to a power socket outlet as possible.

Installez le BNP dans un endroit accessible et aussi près que possible d'une prise de courant.

Der BNP muss möglichst leicht zugänglich und in der Nähe einer Netzsteckdose aufgestellt werden.

Operations Environment

Page number Statement type

page 15

Caution

Attention

Vorsicht

Statement

Install this equipment only in an operations site that is humidity- and temperature-controlled, to ensure compliance with requirements for ambient operational conditions specified in

Table 3 and

Table 15, “Environmental Ranges,” on page 38

Afin de garantir le respect des conditions environnementales de fonctionnement, ce matériel doit être installé exclusivement dans un lieu où l’humidité et la température sont contrôlées.(voir les spécifications dans le Tableau 3 et le

Tableau 15 à la page 38).

Installieren Sie die Geräte nur an einem Betriebsort, der feuchtigkeits- und temperaturgeregelt ist, um die Einhaltung erforderlicher Bedingungen für die Umgebung und den

Betrieb zu gewährleisten.(siehe Spezifikationen in Tabelle 3 und Tabelle 15 auf Seite 38).

Selenio TM BNP 2xr+ Installation Guide 40

Grounding Equipment

Page number Statement type

Page 16

Warning

Avertissement

Warnung

Statement

Le BNP doit être correctement relié à la masse pour assurer un fonctionnement sécurisé.

Avant de connecter le courant ou de mettre en marche le

BNP, reliez le châssis à la masse.

Cette section indique une méthode de mise à la masse. Il peut y en avoir d'autres : vérifiez la configuration de votre réseau pour plus de détails.

Für einen sicheren Betrieb muss der BNP vorschriftsmäßig geerdet sein. Erden Sie das Chassis des BNP, bevor Sie das

Gerät an die Stromversorgung anschließen oder einschalten.

Dieser Abschnitt erläutert eine Erdungsmethode. Eventuell gibt es auch andere Möglichkeiten. Prüfen Sie ihre

Netzwerkkonfiguration, um diesbezügliche Einzelheiten festzustellen.

AC Power Strip Compliance Advisory

Page number Statement type

page 18

Caution

Attention

Vorsicht

Statement

If the BNP is to be connected to a rack-mounted, properly grounded AC power strip, ensure that the strip is compliant with 12AWG UL Certification.

Si le système BNP doit être branché sur un bloc d’alimentation secteur avec mise à la terre monté sur rack, s’assurer que le bloc d’alimentation possède la certification 12AWG UL.

Soll der BNP mit einer ordnungsgemäß geerdeten rackmontierten Wechselstrom-Steckdosenleiste verbunden werden, muss sichergestellt werden, dass die

Steckdosenleiste den Anforderungen der 12AWG UL-

Zertifizierung entspricht.

Qualified Personnel

Page number Statement type

Page 19

Caution

Attention

Vorsicht

Statement

Only trained personnel should install or replace this equipment.

Seul un personnel qualifié devrait installer ou remplacer cet

équipement.

Dieses Gerät darf nur von qualifiziertem Personal aufgestellt und ausgetauscht werden.

Selenio TM BNP 2xr+ Installation Guide 41

Equipment On and Off

Page number Statement type

Page 18

Caution

Attention

Vorsicht

Statement

The BNP does not have an on/off power switch. Connection to the power source powers up the BNP immediately.

Le cordon d'alimentation constitue le mécanisme de déconnexion du BNP. Il n'y a pas d'interrupteur : une fois connecté à la prise de courant, le système est immédiatement mis sous tension.

Der BNP wird mit dem Netzkabel ein- und ausgeschaltet. Es gibt keinen Netzschalter. Beim Einstecken des Netzkabels in die Steckdose wird das Gerät unmittelbar eingeschaltet.

Safety Screw Lock Advisory

Page number Statement type

Page 19

Caution

Attention

Vorsicht

Statement

Make sure that the safety screw is in the locked position

(turned counterclockwise) after the power supply is installed, but before connecting power ( Figure 10 ). Note that the locked position may be different than that of similar units.

This ensures that the power supply cannot be accidentally disconnected, causing possible damage.

Assurez-vous que la vis de sécurité est en position bloquée

(tournée dans le sens contraire des aiguilles d'une montre) après avoir installé l'alimentation, mais avant d'avoir connecté le courant (figure 10).

Notez que la position bloquée peut être différente de celle d'unités similaires.

Ceci constitue la preuve que l'alimentation ne peut pas être déconnectée par accident, et ainsi causer de possible dommages.

Vergewissern Sie sich, dass sich die Sicherheitsschraube in der verriegelten Position befindet (gegen den Uhrzeigersinn), nachdem das Netzteil eingebaut wurde, aber bevor das Gerät an die Stromversorgung angeschlossen wird (Abbildung 10).

Beachten Sie, dass die verriegelte Position anders als bei

ähnlichen Einheiten sein kann. So wird sichergestellt, dass das

Netzteil nicht versehentlich getrennt wird, was zu

Beschädigungen führen kann.

Selenio TM BNP 2xr+ Installation Guide 42

+48V DC Power Supply Advisory

Page number Statement type

Page 20

Caution

Attention

Vorsicht

Statement

These are +48V DC power supplies, not -48V. Please connect accordingly.

Il s'agit d'une alimentation +48V, et non -48V. Connectez en fonction.

Die Netzteile weisen Anschlusswerte von +48 V DC

(Gleichstrom) auf, nicht -48 V. Bitte schließen Sie diese entsprechend an.

Compact Flash Advisory

Page number Statement type

Page 22

Caution

Attention

Vorsicht

Statement

Your license is attached to the compact flash (CF); do not discard it. Even if a CF card fails, keep the device and contact

Imagine Communications technical support for instructions on repair or obtaining a working replacement.

Votre licence se trouve sur la carte mémoire Compact Flash.

Ne l'égarez pas.

Au cas où la carte mémoire Compact Flash serait déficiente, conservez-la et contactez le support technique pour obtenir des instructions concernant la réparation ou le remplacement.

Ihre Lizenz ist auf der Compact Flash-Karte enthalten.

Entsorgen Sie diese nicht. Selbst wenn eine CF-Karte ausfällt, bewahren Sie diese auf, und wenden Sie sich an den technischen Kundendienst von , um Anweisungen für die

Reparatur oder den Austausch durch eine funktionsfähige

Karte zu erhalten.

Power Source Safety Advisory

Page number Statement type

Page 25

Warning

Avertissement

Warnung

Statement

Never replace any FRU while the chassis is still connected to the power source.

Ne remplacez jamais une unité remplaçable sur site si le châssis est toujours connecté à l'alimentation.

Tauschen Sie kein vor Ort austauschbares Teil aus, während das Chassis mit der Stromversorgung verbunden ist.

Selenio TM BNP 2xr+ Installation Guide 43

FRU Replacement Advisory

Page number Statement type

Page 25

Warning

Avertissement

Warnung

ASI Module Replacement Advisory

Statement

Do not replace any component (such as fuses) not specifically described here. For replacement beyond the FRU level, contact your technical support representative for instructions on returning the component. See “Contacting Customer

Support” on page 24 .

Ne remplacez aucun composant (tel que les fusibles) qui ne soit pas spécifiquement décrit ici.

Pour des remplacements au-delà des unités remplaçables sur site, contactez le représentant du support technique pour connaître les instructions à suivre si vous souhaitez renvoyer

le composant. (Voir “Contacting Customer Support” on page 24

Tauschen Sie keine Komponenten (wie Sicherungen) aus, die hier nicht ausdrücklich genannt sind. Beim Austausch von

Komponenten, die keine vor Ort austauschbaren Teile sind, wenden Sie sich an den für Sie zuständigen Mitarbeiter des technischen Kundendiensts, um Anweisungen zum

Zurücksenden der Komponente zu erhalten. (Siehe

“Contacting Customer Support” on page 24 .)

Page number Statement type

Page 32

Caution

Attention

Vorsicht

Statement

ASI modules should always be replaced; no filler should be used.

Les modules ASI doivent toujours être remplacés. N'utilisez jamais de bouche-trou.

ASI-Module müssen immer ersetzt werden. Verwenden Sie keine Blindblenden.

Selenio TM BNP 2xr+ Installation Guide 44

Selenio TM BNP 2xr+ Installation Guide 45

APPENDIX B

Conformity and Safety

This appendix contains compliance and regulatory information pertinent to the

Selenio™ Broadcast Network Processor (BNP), in the following topics:

•

“Declarations of Conformity” on page 47 .

•

“Safety” on page 51 .

The BNP has been certified and is in compliance to the requirements below:

• Subpart B of Part 15 of FCC Rules for Class A digital devices

• Industry Canada Interference Causing Equipment Standard ICES-003,

“Information Technology Equipment (ITE) – Limits and methods of measurement”, Issue 5, dated August 2012 (Class A)

• VCCI Regulations For Voluntary Control Measures of radio interference generated by Information Technology Equipment, dated April 2013 (Class A)

• EN 55022:2010, "Information technology equipment – Radio disturbance characteristics – Limits and methods of measurement" (Class A)

• CISPR 22:2008 "Information technology equipment – Radio disturbance characteristics – Limits and methods of measurement" (Class A)

• AS/NZS CISPR 22:2009: "Information technology equipment – Radio disturbance characteristics – Limits and methods of measurement" (Class A)

• EN 55024:2010 "Information technology equipment – Immunity characteristics, Limits and method of measurement."

• CISPR 24:2010 "Information technology equipment – Immunity characteristics,

Limits and method of measurement."

• EN 61000-3-2:2006 +A1:2009 +A2:2009 – AC Current Harmonics

• EN 61000-3-3:2008 – AC Voltage Fluctuations

This product follows the provisions of the EMC Directive 2004 / 108 / EC and carries the CE marking accordingly.

Selenio TM BNP 2xr+ Installation Guide 46

Declarations of Conformity

Declarations of Conformity

Declarations of conformity pertinent to the BNP are provided in the following sections:

•

“United States,” next.

•

“Canada” on page 48 .

•

“Europe” on page 48 .

•

“Japan” on page 50

•

“Australia/New Zealand” on page 50 .

United States

Declaration of Conformity

Responsible Party Name: Imagine Communications

Address: 390 West Java Drive

Sunnyvale, CA 94089, U.S.A.

Telephone:

Declares that product:

(877) 742-6389

Selenio™ Broadcast Network Processor (BNP) 2xr+

Complies with Part 15 of the FCC Rules.

This device complies with Subpart B of Part 15 of FCC Rules for Class A digital devices. Operations are subject to the following two conditions: (1) This device must not be allowed to cause harmful interference; (2) This device must accept any interference received, including interference that may cause undesired operation.

Modifying the equipment without Imagine Communications’ authorization may result in the equipment no longer complying with FCC requirements for Subpart B of Part 15 of FCC Rules for Class

A or Class B digital devices. In that event, your right to use the equipment may be limited by FCC regulations, and you may be required to correct any interference to radio or television communications at your own expense.

For Class A Equipment

Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Selenio TM BNP 2xr+ Installation Guide 47

Declarations of Conformity

Canada

This Class A digital apparatus complies with Industry Canada Interference Causing Equipment Standard

ICES-003, “Information Technology Equipment (ITE)—Limits and methods of measurement”, Issue 5, dated August 2012 (Class A).

Avis de conformité à la réglementation d’Industrie Canada.

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

Europe

Warning!

This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

EN 55024

Imagine Communications declares that the BNP complies with EN 55024:2010 “Information

Technology Equipment—Immunity Characteristics, Limits and method of measurements. EN 55024 references various international and European standards and for clarity, the standards utilized are

provided in Table 16

Table 16. EN55024 Referenced Standards

Referenced Standard Description

IEC 60050-161:1990 International Electrotechnical Vocabulary (IEV)—

Chapter 161: Electromagnetic compatibility.

IEC 6100-4-2:2008

EN 61000-4-2:2009

IEC 6100-4-3:2006

+A1:2007

+A2:2010

EN 61000-4-3:2006

+A1:2008

+A2:2010

Electromagnetic compatibility (EMC) Part 4: Testing and measurement techniques—”Section 2:

Electrostatic discharge immunity test”.

Section 3: Radiated radio-frequency electromagnetic field immunity test.

Section 4: Electrical fast transient/burst immunity test

IEC 6100-4-4:2004

EN 61000-4-4:2004

IEC 61000-4-5:2005

EN 61000-4-5:2006

IEC 61000-4-6: 2008

EN 61000-4-6:2009

IEC 61000-4-8:2009

EN 61000-4-8:2010

IEC 61000-4-

11:2004

EN 61000-4-11:2004

Section 5: Surge immunity test

Section 6: Immunity to conducted disturbances, induced by radio-frequency fields.

Section 8: Power frequency magnetic field immunity text

Section 11: Voltage dips, short interruptions and voltage variations immunity tests.

Standard Used

IEC 60050-161:1990

IEC 6100-4-2:2008

EN 6100-4-2:2009

IEC 61000-4-2:2006

+A1:2007

+A2:2010

EN 61000-4-3:2006

+A1:2008

+A2:2010

IEC 61000-4-4:2012

EN 61000-4-4:2012

IEC 61000-4-5:2005

EN 61000-4-5:2006

IEC 61000-4-6:2008

EN 61000-4-6:2009

IEC 61000-4-8:2009

EN 61000-4-8:2010

IEC 61000-4-11:2004

EN 61000-4011:2004

Selenio TM BNP 2xr+ Installation Guide 48

Declarations of Conformity

Table 16. EN55024 Referenced Standards

Referenced Standard Description

CISPR 16-1-2:2003

+A1:2004

+A2:2006

EN 55016-1-2:2004

+A1:2005

+A2:2006

Specification for radio disturbance and immunity measuring apparatus and methods—Part 1-2 Radio disturbance and immunity measuring apparatus— ancillary equipment - Conducted disturbances.

CISPR 20:2006

EN 55020-2007

CISPR 22:2008

(mod)

EN 55022-2010

Sound and television broadcast receivers and associated equipment—Immunity characteristics—

Limits and methods of measurement

Information technology equipment—Radio disturbance characteristics—Limits and methods of measurement.

Standard Used

CISPR 16-1-2:2003

+A1:2004

+A2:2006

EN55016-1-2:2004

+A1:2005

+A2:2006

CISPR 20-2006

EN 55020:2007

CISPR 22-2008 (mod)

EN 55022:2010

EN 55022

EN 55022:2010 references various internal and European standards and for clarity, the standards

utilized are provided in Table 17

Table 17. EN550-22 Referenced Standards

Referenced Standard Description

CISPR 16-1-1:2006

+A1:2006

EN 55016-1-1:2007

+A1:2007

Specification for radio disturbance and immunity measuring apparatus and methods—Part 1-1:Radio disturbance and immunity measuring apparatus-

Measuring apparatus

CISPR 16-1-2:2003

+A1:2004

+A2:2006

CISPR 16-1-4:2007

EN 55016-1-4: 2007

Specification for radio disturbance and immunity measuring apparatus and methods—Part 1-2:

Radio disturbance and immunity measuring apparatus- Ancillary equipment - Conducted disturbance

Specification for radio disturbance and immunity measuring apparatus and methods – Part 1-4:

Radio disturbance and immunity measuring apparatus - Ancillary equipment - Radiated disturbances

CISPR 16-2-3:2003

+A1:2005

EN 55016-2-3:2004

+A1:2005

CISPR 16-4-2:2003

EN 55016-4-2 2004

Specification for radio disturbance and immunity measuring apparatus and methods – Part 2-3:

Methods of measurement of disturbances and immunity – Radiated disturbance measurements

Specification for radio disturbance and immunity measuring apparatus and methods – Part 4-2:

Uncertainties, statistics and limit modelling -

Uncertainty in EMC measurements

Standard Used

CISPR 16-1 2006

+A1:2006

+A2:2007

CISPR 16-1:2003

+A1:2004

+A2:2006

CISPR 16-1-4:2007

CISPR-2-3:2006

CISPR 16-4-2:2003

Selenio TM BNP 2xr+ Installation Guide 49

Declarations of Conformity

Japan

Warning!

This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adquate measures.

VCCI Regulations for Voluntary Control Measures of radio interference generated by Information

Technology Equipment, dated April 2013 (Class A).

VCCI regulations reference various national and internal standards and for clarity, the standards utilizaed are provided in

Table 18 .

Table 18. VCCI Referenced Standards

Referenced Standard Description

CISPR 22: Ed 6:2008 Information Technology Equipment – Radio disturbance characteristics -

Limits and methods of measurement

CISPR 16-1-1

Ed2.1:2006

CISPR 16-1-2

Ed1.2:2006

Specification for radio disturbance and immunity measuring apparatus and method – Part 1-1: Radio disturbance and immunity measuring apparatus –

Measuring apparatus.

Specification for radio disturbance and immunity measuring apparatus and methods – Part 1-2: Radio disturbance and immunity measuring apparatus

– Measuring apparatus – Ancillary equipment – Conducted disturbances

CISPR 16-1-4

Ed2.0:2007

CISPR 16-2-3

Ed2.0:2006

CISPR 16-4-2

Ed1.0:2003

ANSI C63.4-2003 and ANSI C63-2009

Specification for radio disturbance and immunity measuring apparatus and methods –Part 1-4: Radio disturbance and immunity measuring apparatus –

Ancillary equipment – Radio disturbances

Specification for radio disturbance and immunity measuring apparatus and methods – Part 2-3: Methods of measurement of disturbance and immunity

– Radiated disturbance measurements

Specification for radio disturbance and immunity measuring apparatus and methods – Part 4-2: Uncertainties, statistics and limit modeling –

Uncertainty in EMC measurements

American National Standard for Method of Measurement of Radio Noise

Emissions from Low Voltage Electrical and Electronic Equipment in the

Range 9kHz to 40 GHz.

Australia/New Zealand

Warning!

This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adquate measures.

AS/NZS CISPR 22:2009: "Information technology equipment – Radio disturbance characteristics –

Limits and methods of measurement" (Class A)

Selenio TM BNP 2xr+ Installation Guide 50

Safety

The BNP has been certified and is in compliance to the following requirements:

• IEC 60950-1:2005 (2nd Edition); Am 1:2009

• EN 60950-1:2006 + A11:2009 + A1:2010 + A12:2011

Safety

Selenio TM BNP 2xr+ Installation Guide 51

Index

Numerics

19-inch rack

HRC

AC power

rack-mount power strip

air flow

ambient and controlled operations environment

temperature and humidity

15, 38

antistatic mat

14, 25, 39

applying power

I installation

18, 19

rack mount

requirements

installing

XFPs

B bracket rack mount

LED indicator

23, 24

LEDs

LEDs, defined

Light Emitting Diodes, see LEDs

Caution mounting location and environmental conditions

chassis

compact flash

electrostatic precautions

ESD

14, 25, 39

wrist strap

14, 25, 39

mapping scheme, SFP port

mat, antistatic

14, 25, 39

module

GBP module

module removal

and shutdown/power off 25

noise emissions

nut, M4 17

F fast Ethernet

Field-replaceable Unit see FRU

front bezel

9, 10, 30, 31

front panel

9, 10

FRU

Panel

port mapping scheme

port connection

connecting ports

power cord

power supply

removing and replacing

GBP module

ground

grounding

bracket

reboot

redundancy

regulatory

requirements for installation 13

Selenio TM BNP 2xr+ Installation Guide 52

serial port

SFP

mapping schemes

STP module

12, 32

T temperature operating

15 storage

tools required

V view front

Warning

do not replace fuses 25

replacing FRU while power up

use ESD 14

wire strippers

XFP installation

Selenio TM BNP 2xr+ Installation Guide 53

வணக்கம்! Imagine Communications BNP 2xr+ Broadcast Network Processor Installation Guide உடன் உங்களுக்கு உதவ சிறப்பாகப் பயிற்றுவிக்கப்பட்ட AI சாட்போட் நான். நான் ஆவணத்தை முழுமையாக மதிப்பாய்வு செய்துள்ளேன், மேலும் உங்களுக்குத் தேவையான சரியான தகவலைக் கண்டறிய அல்லது உள்ளடக்கத்தை தெளிவான மற்றும் எளிமையான சொற்களில் விளக்க உதவ முடியும். குறிப்பிட்ட அம்சங்கள், சரிசெய்தல் படிகள் அல்லது பொதுவான பயன்பாடு குறித்த வழிகாட்டுதலை நீங்கள் தேடுகிறீர்களானால், உங்கள் கேள்விகளைக் கேட்க தயங்கவும். உங்கள் கவலைகள் அல்லது தேவைகள் பற்றி நீங்கள் எவ்வளவு அதிகமாக விவரங்களை வழங்குகிறீர்களோ, அவ்வளவு துல்லியமாகவும் эффективноவும் நான் உங்களுக்கு உதவ முடியும்!

உதவியாளர் தட்டச்சு செய்கிறார்

உதவியாளர் விசைப்பலகையில் இல்லை. தயவுசெய்து, பின்னர் மீண்டும் முயற்சிக்கவும்.

உள்ளடக்க அட்டவணை

உங்கள் தாய்மொழி அல்லாத ஒன்று உட்பட, பல மொழிகளில் எழுதப்பட்ட ஆவணத்தை நீங்கள் அடைந்துவிட்டீர்கள் போல் தெரிகிறது. நீங்கள் விரும்பும் மொழி இல்லாத பக்கங்களை தற்காலிகமாக மறைக்க பின்வரும் இணைப்புகளைப் பயன்படுத்தலாம்.

விளம்பரம்

Installation Guide

Selenio

BNP2xr+ Installation

Guide

Publication Information

Notice

Trademarks

Patents

Contact Information

Support Contact Information

Document Change History

Table of Contents

Introduction

Document Organization

Document Audience

Related Documentation

Document Conventions

Graphics

Overview

In This Chapter:

BNPFront Panel

LED Indicators

Port Mapping

BNP Rear Panel

Configuration Options for PROC3 Combinations

BNP Internal Components

Installation

In This Chapter

Before You Begin

Required Equipment

Site Cabling

Electrostatic Precautions

Rack Mounting the BNP

Installing the BNP into a Rack

Grounding the BNP

Connecting the Chassis Ground

Installing SFP Modules

Connecting AC Power to the BNP

Connecting AC power to a BNP

Connecting DC Power to the BNP

Safety

Preparation

Connecting DC power to a BNP

Connecting External Ports

Fast Ethernet Management Port 10/100-0

Fast Ethernet Management Port 10/100-1

GigE Port

ASI Port

Installing the Compact Flash Card

Troubleshooting

In This Chapter:

LED Indicators

Event Log Analysis

Contacting Customer Support

Field-replaceable Units

In This Chapter:

Overview

Replacing a Power Supply

Removing a Power Supply

Inserting a Power Supply

Removing a GBP3 Module

Replacing a GBP3 Module

Replacing a Processor Module (PROC3) or an ASI

Module

Removing a PROC3 or ASI Module

Replacing a PROC3 or ASI Module

Specifications

In This Chapter:

Input Interfaces/Output Interfaces

MPEG Processing

Video Formats

Audio Formats

Elementary Stream Types & Conversions

Digital Broadcast

Regulatory Compliance

Electrical/Mechanical

Environmental

Localized Cautions and Warnings

Conformity and Safety

Declarations of Conformity